User`s guide | Extron electronic PVT CV Satellite Radio User Manual

User’s Guide
PVT CV, PVT RGB CV,
PVT RGB and PVT SW RGB
PoleVault™ Twisted Pair Transmitters
(Rack Mount Models)
68-1310-01
Rev. C
04 07
Precautions
Safety Instructions • English
This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions in
the literature provided with the equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of
electric shock.
Caution
Read Instructions • Read and understand all safety and operating
instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future
reference.
Follow Warnings • Follow all warnings and instructions marked on the
equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not
recommended by the equipment manufacturer because they may be
hazardous.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation et
la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence
dans le boîtier de l’appareil de tensions dangereuses
non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de
sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir
les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et consignes
marqués sur le matériel ou présentés dans la documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils
non recommandés par le fabricant du matériel car cela risquerait de poser
certains dangers.
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im
Lieferumfang enthaltenen Dokumentation
besonders wichtige Hinweise zur Bedienung und
Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam
machen, daß im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen, die nicht isoliert
sind und die einen elektrischen Schock verursachen
können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,
sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen
und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit
des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und
Anleitungen auf dem Gerät oder in der Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,
die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine
Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario
sobre instrucciones importantes de operación y
mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación
suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre
la presencia de elementos con voltaje peligroso sin
protección aislante, que puedan encontrarse dentro
de la caja o alojamiento del producto, y que puedan
representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y
seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para
futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones marcadas
en el equipo o en la documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no
sean especificamente recomendados por el fabricante, ya que podrian
implicar riesgos.
Warning
Power sources • This equipment should be operated only from the power source
indicated on the product. This equipment is intended to be used with a main power
system with a grounded (neutral) conductor. The third (grounding) pin is a safety
feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all power
cords from the rear of the equipment, or the desktop power module (if detachable),
or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to be
stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no userserviceable parts inside. To prevent the risk of shock, do not attempt to service
this equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are
provided to prevent overheating of sensitive components inside. These openings
must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly
replaced. Replace it only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer’s
instructions.
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation
indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale
comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue
un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,
déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module
d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de
manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas
écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparationmaintenance par un technicien qualifié. Aucun des éléments internes ne peut être
réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit
pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des
couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci
servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures
ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie.
Remplacer uniquement avec une batterie du meme type ou d’un ype equivalent
recommande par le constructeur. Mettre au reut les batteries usagees conformement
aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene
Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit einer
Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte
Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese
sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten
Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen Stomversorgung
(falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im
Weg liegen und niemand darauf treten kann oder Objekte darauf- oder unmittelbar
dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem Servicepersonal
durchgeführt werden. Die internen Komponenten des Gerätes sind wartungsfrei.
Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses
Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines
elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist,
dienen diese zur Vermeidung einer Überhitzung der empfindlichen Teile im
Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt
wird. Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen
vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen Sie
verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo
de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este
equipo debe provenir de un sistema de distribución general con conductor neutro
a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia
ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida
de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación
en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera
independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben
instalar en lugares donde no sean pisados ni apretados por objetos que se puedan
apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal
calificado. En el interior no hay partes a las que el usuario deba acceder. Para evitar
riesgo de electrocución, no intentar personalmente la reparación/mantenimiento
de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes
peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,
es para evitar el sobrecalientamiento de componentes internos sensibles. Estas
aberturas nunca se deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición
incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas siguiendo las
instrucciones del fabricante.
Precautions
ᅝܼ乏ⶹ噝Ё᭛
䖭Ͼヺোᦤ⼎⫼᠋䆹䆒໛⫼᠋᠟‫ݠ‬Ё
ⱘ᪡԰੠㓈ᡸ䇈ᯢDŽ
䖭Ͼヺো䄺ਞ⫼᠋䆹䆒໛ᴎ໇‫ݙ‬ᲈ
䴆ⱘॅ䰽⬉य़ˈ᳝㾺⬉ॅ䰽DŽ
⊼ᛣ
䯙䇏䇈ᯢк噝⫼᠋Փ⫼䆹䆒໛ࠡᖙ乏䯙䇏ᑊ⧚㾷
᳝ᅝܼ੠Փ⫼䇈ᯢDŽ
ֱᄬ䇈ᯢк噝⫼᠋ᑨֱᄬᅝܼ䇈ᯢкҹ໛ᇚᴹՓ⫼DŽ
䙉ᅜ䄺ਞ噝⫼᠋ᑨ䙉ᅜѻક੠⫼᠋ᣛफϞⱘ᠔᳝
ᅝܼ੠᪡԰䇈ᯢDŽ
䙓‫ܡ‬䗑ࡴ噝ϡ㽕Փ⫼䆹ѻકॖଚ≵᳝᥼㤤ⱘᎹ‫៪݋‬
䗑ࡴ䆒໛ˈҹ䙓‫ॅܡ‬䰽DŽ
䄺ਞ
⬉⑤噝䆹䆒໛া㛑Փ⫼ѻકϞᷛᯢⱘ⬉⑤DŽ䆒໛ᖙ⫼᳝
ഄ㒓կ⬉㋏㒳կ⬉DŽ㄀ϝᴵ㒓˄ഄ㒓˅ᰃᅝ䆒ᮑˈϡ㛑ϡ
⫼៪䏇䖛DŽ
ᢨᥝ⬉⑤噝ЎᅝܼഄҢ䆒໛ᢨᥝ⬉⑤ˈ䇋ᢨᥝ᠔᳝
໛ৢ៪Ḡ䴶⬉⑤ⱘ⬉⑤㒓ˈ៪ӏԩ᥹ࠄᏖ⬉㋏㒳
⬉⑤㒓DŽ
⬉⑤㒓ֱᡸ噝ཹ୘Ꮧ㒓ˈ䙓‫ܡ‬㹿䏽䏣ˈ៪䞡⠽᣸य़DŽ
㓈ᡸ噝᠔᳝㓈ׂᖙ乏⬅䅸䆕ⱘ㓈ׂҎਬ䖯㸠DŽ䆒໛
䚼≵᳝⫼᠋ৃҹ᳈ᤶⱘ䳊ӊDŽЎ䙓‫⦄ߎܡ‬㾺⬉ॅ
ϡ㽕㞾Ꮕ䆩೒ᠧᓔ䆒໛Ⲫᄤ㓈ׂ䆹䆒໛DŽ
䗮亢ᄨ噝᳝ѯ䆒໛ᴎ໇Ϟ᳝䗮亢ῑ៪ᄨˈᅗӀᰃ⫼
䰆ℶᴎ‫ݙ‬ᬣᛳ‫ܗ‬ӊ䖛⛁DŽϡ㽕⫼ӏԩϰ㽓ᣵԣ䗮亢ᄨDŽ
䫖⬉∴噝ϡℷ⹂ⱘ᳈ᤶ⬉∴Ӯ᳝⟚⚌ⱘॅ䰽DŽᖙ乏Փ
Ϣॖᆊ᥼㤤ⱘⳌৠ៪Ⳍ䖥ൟোⱘ⬉∴DŽᣝ✻⫳ѻॖⱘ
䆂໘⧚ᑳᓗ⬉∴DŽ
This page was deliberately left blank.
Table of Contents
Chapter One • Introduction..................................................... 1-1
About the PVT Transmitters.................................................... 1-2
Transmission distance. ........................................................... 1-2
About the PVT CV................................................................... 1-3
About the PVT RGB ................................................................ 1-3
About the PVT RGB CV........................................................... 1-4
About the PVT SW RGB.......................................................... 1-4
Application Diagram................................................................. 1-5
Chapter Two • Installation....................................................... 2-1
UL/Safety Requirements.......................................................... 2-2
Important safety instructions................................................ 2-2
Installing the PVT Twisted Pair Transmitters..................... 2-3
Tabletop use............................................................................ 2-3
UL requirements for rack mounted devices.......................... 2-3
Rack mounting........................................................................ 2-3
Furniture mounting................................................................ 2-5
Connections and Settings........................................................ 2-6
Front panel features............................................................... 2-6
Rear panel features................................................................. 2-8
Cable termination for composite video and audio
transmission...................................................................... 2-9
Cable termination for RGB video and
audio transmission.......................................................... 2-11
Appendix A • Reference Material ......................................A-1
Specifications...............................................................................A-2
Part Numbers...............................................................................A-4
Included parts.........................................................................A-4
Optional Accessories.................................................................A-5
All trademarks mentioned in this manual are the properties of their respective owners.
68-1310-01
Rev. C
04 07
PVT Series (Rack Mount Models) • Table of Contents
i
Table of Contents, cont'd
ii
This page was deliberately left blank.
PVT Series (Rack Mount Models) • Table of Contents
PVT Series (Rack Mount Models)
1
Chapter One
Introduction
About the PVT Transmitters
Application Diagram
Introduction
About the PVT Transmitters
The Extron ����������������������
PVT Series (PoleVault™ Twisted Pair Transmitters)
are a series of cost effective twisted pair transmitters that work
exclusively with the PVS 204SA, a four-input twisted pair
switcher with a built in power amplifier.
PVT transmitters can transmit composite video and stereo audio
or high resolution video (RGB) and stereo audio to the
PVS 204SA switcher over CAT 5 twisted pair cable, up to a
distance of 100 feet. All transmitters are remotely powered
via the twisted pair cable when connected to the PVS 204SA
switcher.
N
This manual covers the rack mount models only.
For Decora® and AAP models, refer to the manual (part
number 68-1259-01) for those devices.
N
PVT series of transmitters are compatible ONLY
with the PVS 204SA switcher.
N
For PVS 204SA installation and operation information,
refer to the manual supplied with the device.
The PVT transmitter rack mount models can be mounted on 1U
19" or standard rack shelves, or mounted under or on desks.
The PVT series rack mount models are as follows:
PVT CV — Transmits composite video and stereo audio.
PVT RGB, PVT SW RGB — Transmits computer (RGB) video
and stereo audio.
PVT RGB CV — Transmits composite video, computer video
and two stereo audio signals.
See the "About the PVT xx" sections in this chapter for details.
The PVT transmitters are part of a system for distribution of
composite or computer video and audio, over Extron Enhanced
Skew-Free™ A/V UTP Cable, or any CAT 5, 5e, or 6 shielded
twisted pair (STP), unshielded twisted pair (UTP), or foil
shielded twisted pair (FTP) cable.
Transmission distance
The maximum distance is determined by the frequency and
resolution of the signal that is input to the transmitter. However,
all PVT models can transmit signals to the PVS 204SA switcher
if it is located not more than 100 feet away. The optimum
distance is between 50 and 75 feet.
1-2
PVT Series (Rack Mount Models) • Introduction
About the PVT CV
The PVT CV Twisted Pair Transmitter is a 1/8 rack mounting
model that can transmit composite video and stereo audio to the
PVS 204SA switcher. This model can also be mounted under a
desk or shelf, or on certain projector poles.
AUDIO
IN
VIDEO
IN
L
R
PVT CV
VIDEO OUT
Figure 1-1 — PVT CV face and rear panel
About the PVT RGB
The PVT RGB Twisted Pair Transmitter is a 1/4 rack mounting
model that can transmit high resolution (RGB) video and an
associated stereo audio signal to the PVS 204SA switcher. It has
a local monitor output for image monitoring. This model can
also be mounted under a desk or shelf, or on certain projector
poles.
PVT RGB
PVT RGB
RGB A OUT
INPUT
MONITOR OUT
RGB B OUT
Figure 1-2 — PVT RGB face and rear panel
PVT Series (Rack Mount Models) • Introduction
1-3
Introduction, cont’d
About the PVT RGB CV
The PVT RGB CV Twisted Pair Transmitter is a 1/4 rack
mounting model that can transmit high resolution (RGB) video
and composite video, and two associated stereo audio signals to
the PVS 204SA switcher. This model can also be mounted under
a desk or shelf, or on certain projector poles.
RGB
VIDEO
PVT RGB CV
RGB A OUT
AUDIO
IN
VIDEO
IN
AUDIO IN
L
COMPUTER IN
R
VIDEO OUT
RGB B OUT
Figure 1-3 — PVT RGB CV face and rear panel
About the PVT SW RGB
The PVT SW RGB Twisted Pair Transmitter is a 1/4 rack
mounting model with two input connectors, a local monitor
output, and a remote contact closure connector. It transmits
high resolution (RGB) video and stereo audio signals to the
PVS 204SA, and switches between the two inputs by front
panel, remote, or auto switching. In addition, the local monitor
output can be set to accept only the input 1 signal, or to follow
the current active input signal. This model can also be mounted
under a desk or shelf, or on certain projector poles.
AUTO
SWITCH
AUTO ON
1
2
FOLLOW
MONITOR
MANUAL
INPUT 1
PVT SW RGB
REMOTE
INPUT 1
PIN1 - IN 1
PIN 4 - IN 2
PIN 5 - GND
INPUT 2
RGB A OUT
CONTACT
MONITOR OUT
RGB B OUT
Figure 1-4 — PVT SW RGB face and rear panel
1-4
PVT Series (Rack Mount Models) • Introduction
Application Diagram
Extron
SI 26X
Extron
SI 26X
Two-way, Open Back
Ceiling Speakers – 1 Pair
Option
Two-way, Open Back
Ceiling Speakers – 1 Pair
Extron
SPK 18 - 25'
Cable
Included
Extron
PCM 240
Projector Drop
Ceiling Mount
Extron
PMP
Projector
Mount Pole
Extron
PVS 204SA
PoleVault ™
Switcher
D
Ohms
4/8
OUTPUTS
AMPLIFIE
R
L
GROUND
NOTSHORT
DO OR OUTPUTS!
17TT
SPEAKER
LISTED
AUDIO/VIDEO
US APPARATUS
MLC/IR
12V
IR
RS-232
Rx
Tx
DC
VOL
E
10V
VOL/MUT
®
A
B
C
IN
RGB
O
U
T
P
U
T
S
VIDEO
3A
AUX/MIX
2A
RGB
1A
VIDEO
3B
I
N
P
U
T
S
POWER
2B
1B
Extron
PMK 350
12V MAX
3A
Multi-product Projector
Mounting Kit
Hardwired IR Cable
to Switcher Included
Extron
UPB 25
Universal Projector
Mounting Bracket
DI
SP
Y
LA
OF
F
ON
PC
RS-232 Cable
to Projector
Included
UTP Cable
Included
VO
L
VO
VID
EO
L
ML
C 52
Extron
MLC 52 RS
Basic MediaLink
Controller
Extron
PVT RGB CV
Line Level
Audio
VGA, Composite Video
W/Audio UTP Transmitter
ACT
IVE
MUT
MIC
E
IN
AU
VID
EO
IN
DIO
IN
L
AU
DIO
R
IN
RG
CO
VID
MP
EO
B
UT
OU
ER
T
A OU
IN
RG
B
B OU
Extron
MLP 101 D
T
T
Mic to Line Preamplifier
Option
Extron
PVT CV
DVD/VCR Combo
Composite Video
w/ Audio UTP
Transmitter
Option
Laptop
w/ Audio
VID
EO
IN
AU
DIO
IN
L
R
VID
EO
OU
T
Aux. Video Source
Figure 1-5 — Typical PVT series system application
using PVT RGB CV and PVT CV transmitters with the
PVS 204SA and other Extron devices
PVT Series (Rack Mount Models) • Introduction
1-5
Introduction, cont'd
1-6
This page was deliberately left blank.
PVT Series (Rack Mount Models) • Introduction
PVT Series (Rack Mount Models)
2
Chapter Two
Installation
UL/Safety Requirements
Installing the PVT Twisted Pair Transmitters
Connections and Settings
Installation
UL/Safety Requirements
The Underwriters Laboratories (UL) requirements listed below
pertain to the safe installation and operation of the transmitters.
Important safety instructions
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with a dry cloth.
7.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9.
Do not defeat the safety purpose of the polarized or
grounding type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
2-2
PVT Series (Rack Mount Models) • Installation
Installing the PVT Twisted Pair Transmitters
The PVT CV is a 1/8 rack shelf mountable transmitter, and
the PVT RGB, PVT RGB CV, and PVT SW RGB are 1/4 rack
shelf mountable transmitters. Each of the four models can
be mounted under a desk or shelf, or on to certain projector
mounts, and are also suitable for tabletop use.
Tabletop use
The PVT comes with self-adhesive rubber feet attached to the
four corners of the bottom. Set the PVT on a horizontal surface.
UL requirements for rack mou��������������
nted devices
The following Underwriters Laboratories (UL) requirements
pertain to the safe installation of the PVT transmitter in a rack.
1.
Elevated operating ambient temperature — If installed in
a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater than
room ambient temperature. Therefore, install the device
in an environment compatible with the maximum ambient
temperature (Tma = +122 °F, +50 °C) specified by Extron.
2.
Reduced air flow — Install the equipment in a rack so that
the amount of air flow required for safe operation of the
equipment is not compromised.
3.
Mechanical loading — Mount the equipment in the rack
so that a hazardous condition is not achieved due to
uneven mechanical loading.
4.
Circuit overloading — Connect the equipment to
the supply circuit and consider the effect that circuit
overloading might have on overcurrent protection and
supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this
concern.
5.
Reliable earthing (grounding) — Maintain reliable
grounding of rack-mounted equipment. Pay particular
attention to supply connections other than direct
connections to the branch circuit (e.g., use of power strips).
Rack mounting
For rack mounting, mount the PVT on a VersaTools® 19" 1U
rack shelf (RSF 123, part #60-190-20 or RSB 123, #60-604-20)
(figure 2-1) or on a standard 1U rack shelf (RSU 129, part #60190-01 or RSB 129, #60-604-01) (figure 2-2). On standard rack
shelves, the PVT CV can be mounted in one of eight locations to
the rear or the front of the rack, and the PVT RGB and RGB CV
in one of four locations to the rear or front of the rack.
PVT Series (Rack Mount Models) • Installation
2-3
Installation, cont’d
To rack mount a PVT transmitter, do the following:
1.
If installed, remove the feet from the bottom of the PVT.
2.
Mount the PVT using two 4-40 x 3/16" screws in opposite
(diagonal) corners to secure the PVT to the shelf.
3.
Install blank panel(s) or other unit(s) to the rack shelf.
VersaTools
Rack Shelf
Eighth Rack
Width Device
Quarter Rack
Width Device
Quarter and Eighth
Rack Width False
Front Face Plate
(2) 4-40 x 3/16"
Screws
Figure 2-1 — Mounting the PVT on a VersaTools rack
shelf
Quarter Rack
Width Device
Eighth Rack
Width Device
DIS
MDA
TR
IBU
SE
RIES
TIO
N AM
PL
IFIE
R
Figure 2-2 — Mounting the PVT on a standard rack
shelf
2-4
PVT Series (Rack Mount Models) • Installation
Furniture mounting
Use the optional mounting kit (MBU 123, under desk mounting
kit, part #70-212-01) to mount the PVT as follows:
1.
If installed, remove the feet from the bottom of the PVT.
2.
Attach the mounting brackets to the PVT with the machine
screws provided (figure 2-3).
Figure 2-3 — Mounting the PVT under a desk
3.
Hold the PVT with the attached brackets against the
underside of the mounting surface. Mark the bracket
screw hole locations on the mounting surface.
4.
Drill four 3/32" (2 mm) diameter pilot holes, 1/4" (6.3 mm)
deep in the mounting surface at the marked locations.
5.
Insert #8 wood screws into the pilot holes. Tighten the
screws until just less than 1/4" of the head protrudes.
6.
Align the mounting screws with the slots in the brackets
and place the PVT against the surface, with the screws
through the bracket slots.
7.
Slide the PVT slightly forward or back, then tighten all
four screws to secure the PVT in place.
PVT Series (Rack Mount Models) • Installation
2-5
Installation, cont’d
Connections and Settings
Do not connect these devices to a computer data
or telecommunications network. Do not connect
these devices to an MTP system.
N
Front panel features
The front panel features are the same for the PVT CV, PVT RGB,
and PVT RGB CV. The PVT SW RGB features are unique to that
model.
1
PVT CV
PVT CV
1
PVT RGB
PVT RGB
1
RGB
VIDEO
PVT RGB CV
PVT RGB CV
2
AUTO
SWITCH
3
1
4
2
AUTO
ON
FOLLOW
MONITOR
MANUAL
INPUT 1
PVT SW RGB
PVT SW RGB
Figure 2-4 — PVT series front panel features
2-6
PVT Series (Rack Mount Models) • Installation
a
b
c
d
Dual color power LED — This LED lights amber when
power only (no signal) is applied to the PVT, and green
when power and a signal are both present.
Auto switch LED (PVT SW RGB only) — This LED
lights green when the unit is in auto switch mode.
Input selection button with LED (PVT SW RGB only) —
Press these buttons to select (switch) between inputs
1 and 2. The associated LEDs lights green when
the input has an active video signal connected, and
amber when there is no signal present.
1
Dual configuration dual DIP switch (PVT SW RGB only) —
The left DIP switch allows the user to
FOLLOW
AUTO ON
select the switching mode, and the right
MONITOR
DIP switch allows the user to configure
INPUT 1
MANUAL
the local monitor output from the rear
panel.
Switching mode (left DIP switch):
Set the switch up to Auto for automatic switching of the inputs
with an active signal.
N
AUTO
SWITCH
When turning off auto switching, the PVT goes back to
the input that was selected prior to turning the autoswitching on.
Set the switch down to Manual for front panel input switching
or input switching by contact closure control.
N
In Auto mode, if both inputs have an active signal, Input 1 has priority.
Local monitor output (right DIP switch):
Set the switch up to Follow for automatic switching of the local
monitor output to the current selected input.
Set the switch down to Input 1 for local monitor output of the
signal from input 1 only.
PVT Series (Rack Mount Models) • Installation
2-7
Installation, cont’d
Rear panel features
For all PVT rack mount models, the input connectors and the
output connectors are on the rear panel (see figure 2-5).
1
2
AUDIO
IN
L
VIDEO
IN
R
VIDEO OUT
PVT CV
3
2
4
AUDIO
IN
AUDIO IN
1
RGB A OUT
6a
L
VIDEO
IN
COMPUTER IN
6b
6a
R
VIDEO OUT
PVT RGB CV
3
RGB B OUT
5
PVT RGB
RGB A OUT
6a
MONITOR OUT
INPUT
6b
6a
RGB B OUT
PVT RGB
5
5
4
7
8
4
REMOTE
INPUT 1
PIN1 - IN 1
PIN 4 - IN 2
PIN 5 - GND
RGB A OUT
6a
CONTACT
6b
6a
INPUT 2
PVT SW RGB
5
MONITOR OUT
4
RGB B OUT
7
Figure 2-5 — PVT rear panel features
2-8
PVT Series (Rack Mount Models) • Installation
a
b
Composite video input (CV and RGB CV models) —
To input a composite video signal from a suitable source,
connect a male RCA plug to this yellow female RCA jack.
Audio (left and right) input (CV and RGB CV models) —
For unbalanced left and right audio input, insert male RCA
plugs from the audio source, into these two female RCA jacks
(white = left, red = right).
Tip (Signal)
Right Channel
(Red Jacket)
Sleeve (Gnd )
Left Channel
(White Jacket)
Tip (+)
Sleeve ( )
Figure 2-6 — RCA audio connectors
video/audio output (CV and RGB CV models) —
c Composite
For composite video and audio output, using TP cable, connect
this RJ-45 female output port to one of the two composite
video RJ-45 input connectors (labeled 3 and 4), on the rear panel
of the PVS 204SA switcher (see figure 2-8).
Cable termination for composite video and audio transmission
N
The PVT cable termination method is specific for PVT
transmitters working with the PVS 204SA switcher.
DO NOT connect these devices to an MTP system.
N
RJ-45 termination with CAT 5, CAT 5e, CAT 6, and
Skew-Free A/V UTP cable must comply with the
TIA/EIA T 568A wiring standards for all connections.
N
For composite video signals, the RJ-45 connector must
be wired exactly as shown in figure 2-7, so that the input
video and audio signals are transmitted correctly.
PVT Series (Rack Mount Models) • Installation
2-9
Installation, cont’d
Clip Down
Side
Pins 1 2 3 4 5 6 7 8
TP Cable and
CAT 5 connector
Composite
Video and Audio signal
568A
Wire color
Pin
RJ-45
connector
1
White-green
Video +
2
Green
Video –
3
White-orange
+ 5 VDC
4
Blue
Audio L +
5
White-blue
Audio L –
6
Orange
GND
7
White-brown
Audio R +
8
Brown
Audio R –
12345678
Twisted
pairs
1&2
3&6 4&5 7&8
Figure 2-7 — Wiring the twisted pair composite
video and audio cable
PVT CV
VIDEO
IN
PVT RGB CV
PVS 204SA
AUDIO
IN
L
R
VIDEO OUT
RGB A OUT
AUDIO
IN
VIDEO
3
VIDEO
IN
AUDIO IN
L
COMPUTER IN
R
TP cable from
PVT Output
VIDEO OUT
RGB B OUT
Rear Panel
Rear Panel
4
TP cable from
PVT Output
Composite Video Input Connectors
on Rear Panel of PVS 204SA
Figure 2-8 — Connecting the PVT composite video
outputs to the PVS 204SA switcher
d
Audio input (RGB CV, RGB and SW RGB models) —
Plug a 3.5 mm stereo audio plug into this jack for
unbalanced audio input. Wire the plug as shown in
figure 2-9.
N
Figure 2-9 shows a typical audio connector, which
consists of tip, ring, and sleeve.
Tip (L)
Ring (R)
Sleeve ( )
Figure 2-9 — 3.5 mm stereo audio plug
2-10
AUDIO IN
PVT Series (Rack Mount Models) • Installation
e
RGB video input (RGB CV, RGB, and SW RGB models) —
Connect a computer video source to this 15-pin HD
connector for high resolution RGB video input.
ä
RGB cable A output (RGB CV, RGB, and SW RGB models) —
ã
RGB cable B output (RGB CV, RGB, and SW RGB models) —
Using TP cable, connect this RJ-45 female output port,
labeled "RGB A out", to one of the two input ports
(labeled 1A and 2A) on the PVS 204SA switcher.
Using TP cable, connect this RJ-45 female output port,
labeled "RGB B out", to one of the two input ports
(labeled 1B and 2B) on the PVS 204SA switcher.
Cable termination for RGB video and audio transmission
N
The PVT cable termination method is specific for PVT
transmitters working with the PVS 204SA switcher.
DO NOT connect these devices to an MTP system.
N
RJ-45 termination with CAT 5, CAT 5e, CAT 6, and
Skew-Free A/V UTP cable must comply with the
TIA/EIA T 568A wiring standards for all connections.
N
For RGB signals, the RJ-45 connectors must be wired
exactly as shown in the figure 2-10, using the same
wiring table for both ends, so that the correct input
signal (video on cable A and audio on cable B) is carried.
N
Cable B carries the audio signal, the vertical sync
information, and 5 VDC to power the PVT transmitters.
Side
Clip Down
Pins 1 2 3 4 5 6 7 8
TP Cable and
CAT 5 Connector
568A
Pin Wire Color
Cable A
Cable B
1
White-green
Red +
V. sync +
2
Green
Red –
V. sync –
3
White-orange
H. sync +
+ 5 VDC
4
Blue
Green +
Audio L +
5
White-blue
Green –
Audio L –
6
Orange
H. sync –
GND
7
White-brown
Blue +
Audio R +
8
Brown
Blue –
Audio R –
RJ-45
Connector
12345678
Twisted
Pairs
1&2
3&6 4&5 7&8
Figure 2-10 — Wiring twisted pair cables A and B
PVT Series (Rack Mount Models) • Installation
2-11
Installation, cont’d
PVT SW RGB
PVT RGB
TP Cable from
output A
PVS 204SA
RGB A OUT
INPUT 2
RGB
1A
MONITOR OUT
POWER
RGB B OUT
TP Cable from
output B
PIN 1 — IN 1
PIN 4 — IN 2
PIN 5 — GND
RGB A OUT
CONTACT
2A
I
N
P
U
T
S
MONITOR OUT
RGB B OUT
Rear
Panel
1B
Rear Panel
REMOTE
TPINPUT
Cable1 from
output A
2B
12V
3A MAX
TP Cable from
output B
RGB Input Connectors on
Rear Panel of PVS 204SA
Figure 2-11 — Connecting RGB outputs A and B to
the PVS 204SA switcher
g
Monitor output (RGB and SW RGB models) —
Connect a local monitor device to this 15-pin HD
connector to view the video input.
N
h
2-12
MONITOR OUT
The PVT SW RGB allows the user to view the image
from input 1 only or, by adjusting the front panel DIP
switch, to view the image from either input 1 or input 2.
Remote contact closure connector (SW RGB model only) —
Connect a contact closure device to this 15-pin HD connector
to switch between input 1 and input 2 video signals. The
connector has the pin assignments as shown in the table below.
Pin
Function
1
2
3
4
5
6
7
8
9
Input #1
Not used
Not used
Input #2
Ground
Not used
Not used
Not used
Not used
REMOTE
PIN 1 — IN 1
PIN 4 — IN 2
PIN 5 — GND
PVT Series (Rack Mount Models) • Installation
CONTACT
PVT Series (Rack Mount Models)
A
Appendix A
Reference Material
Specifications
Part Numbers
Optional Accessories
Reference Material
Specifications
N
These transmitters are compatible only with the Extron
PVS 204SA. They are not compatible with other models of
twisted pair receivers.
Video — RGB (RGB models)
Gain ................................................. Unity
Video input and loop-through — RGB (RGB models)
Number/signal type...................... 1 VGA-UXGA RGBHV, RGBS
(2 for PVT SW RGB, and 1 buffered loop
through)
Connectors...................................... 1 female 15-pin HD (2 for PVT SW RGB)
Nominal level................................. 0.7 Vp-p for RGB
Minimum/maximum levels......... Analog: 0.3 V to 1.5 Vp-p with no offset
Impedance . .................................... 75 ohms
Horizontal frequency..................... 15 kHz to 130 kHz
Vertical frequency........................... 30 Hz to 150 Hz
Return loss ..................................... <-30 dB @ 5 MHz
DC offset (max. allowable)........... 250 mV
Video output — RGB (RGB models)
Number/signal type...................... 2 analog proprietary signals
Connectors ..................................... 2 female RJ‑45
Sync — RGB (RGB models)
Input type . ..................................... RGBHV, RGBS
Input level ...................................... 3.5 V to 5.5 Vp-p, unterminated
Input impedance ........................... 510 ohms
Max. input voltage......................... 5.5 Vp-p
Video — composite video (CV models)
Gain ................................................. Unity
Differential phase error ................ <1.0º at 3.58 MHz and 4.43 MHz
Differential gain error . ................. <1.0% at 3.58 MHz and 4.43 MHz
Video input — composite video (CV models)
Number/signal type...................... 1 composite video
Connectors ..................................... 1 female RCA
Nominal level................................. 1 Vp-p for composite video
Minimum/maximum levels......... Analog: 0.3 V to 1.5 Vp-p with no offset
A-2
PVT Series (Rack Mount Models) • Reference Material
Impedance . .................................... 75 ohms
Return loss ..................................... <-30 dB @ 10 MHz
DC offset (max. allowable)........... 100 mV
Video output — composite video (CV models)
Number/signal type...................... 1 analog proprietary signal
Connectors ..................................... 1 female RJ‑45
Sync — composite video (CV models)
Standards......................................... NTSC 3.58, NTSC 4.43, PAL, SECAM
Audio input
Number/signal type...................... 1 stereo, unbalanced (2 for PVT SW RGB)
Connectors
RGB models........................ (1) 3.5 mm mini audio jack (tip, ring,
sleeve), (2 for PVT SW RGB)
CV models........................... 1 pair female RCA
Impedance . .................................... >10k ohms unbalanced, AC coupled
Nominal level................................. -10 dBV (316 mVrms)
Maximum level ............................. +11 dBV, (unbalanced) at 1% THD+N
N
0 dBu = 0.775 Vrms, 0 dBV =1 Vrms, 0 dBV ≈ 2 dBu
Audio output to a PVS 204SA
Number/signal type . ................... 1 analog proprietary signal
Connectors ..................................... 1 female RJ‑45
General
External power supply.................. Remote power from PVS 204SA
Power input requirement.............. 5 VDC, TBD A
Rack mount
PVT CV
PVT RGB
PVT SW RGB
PVT RGB CV....................... Yes, with optional 1U rack shelf,
part # 60-190-01, or Versa Tools rack shelf,
part # 60-190-02 or 60-604-20.
Furniture mountable with optional
part # 70-212-01
Enclosure type ............................... Metal
PVT Series (Rack Mount Models) • Reference Material
A-3
Reference Material, cont’d
Enclosure dimensions
PVT CV
1/8 rack Versa Tools..... 1.7" H x 2.2" W x 3.0" D
4.3 cm H x 5.6 cm W x 7.6 cm D
PVT RGB, PVT SW RGB, PVT RGB CV
1/4 rack Versa Tools..... 1.7" H x 4.3" W x 3.0" D
4.3 cm H x 10.9 cm W x 7.6 cm D
(Depths excludes connectors.)
Product weight............................... 1 lbs (0.5 kg).
Shipping weight............................. 2 lbs (1 kg)
Vibration . ....................................... ISTA 1A in carton
(International Safe Transit Association)
Listings............................................ UL, CUL
Compliances.................................... CE, FCC Class A, VCCI, AS/NZS, ICES
MTBF................................................ 30,000 hours
Warranty . ....................................... 3 years parts and labor
N
All nominal levels are at ±10%.
N
Specifications are subject to change without notice.
Part Numbers
Item
Part number
PVT CV
60-827-01
PVT RGB
60-821-01
PVT RGB CV
60-828-01
PVT SW RGB
60-826-01
Included Parts
Included parts
Replacement
part number
Tweeker (small screwdriver)
Rubber feet
User’s manual
A-4
PVT Series (Rack Mount Models) • Reference Material
Optional Accessories
Item
Part number
MBU 123, under desk mounting kit
70-212-01
MBB 100, back of rack mounting kit
70-367-01
RSF 123, 3.5" deep rack shelf mounting kit
60-190-20
RSB 123, 3.5" deep basic rack shelf mounting kit
60-604-20
RSU 129, 9.5" deep rack shelf mounting kit
60-190-01
RSB 129, 9.5" deep basic rack shelf mounting kit
60-604-01
KP 6 Keyboard remote control
60-111-01
Enhanced Skew-Free A/V UTP cables
26-569-xx
Enhanced Skew-free A/V UTP cables-plenum
26-570-xx
CAT 5 cable, 35', plenum
26-637-35
CAT 5 cable, 50', plenum
26-637-50
CAT 5 cable, 75', plenum
26-637-75
CAT 5 cable, 100', plenum
26-637-100
PVT Series (Rack Mount Models) • Reference Material
A-5
Reference Material, cont’d
A-6
This page was deliberately left blank.
PVT Series (Rack Mount Models) • Reference Material
FCC Class A Notice
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his own expense.
Note: This unit was tested with shielded cables on the peripheral devices. Shielded
cables must be used with the unit to ensure compliance.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Extron’s Warranty
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron Electronics 1001 East Ball Road
Anaheim, CA 92805, USA
Asia:
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Europe, Africa, and the Middle East:
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
Japan:
Extron Electronics, Japan
Kyodo Building,
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or nonExtron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
www.extron.com
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
800.633.9876 714.491.1500
FAX 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort, The Netherlands
+800.3987.6673 +31.33.453.4040
FAX +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Rd. #04-01
PM Industrial Bldg., Singapore 368363
+800.7339.8766 +65.6383.4400
FAX +65.6383.4664
© 2007 Extron Electronics. All rights reserved.
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
+81.3.3511.7655 FAX +81.3.3511.7656
Download PDF

advertising