Extron electronic XPA 1002 Stereo Amplifier User Manual

User’s Manual
XTRA Series: XPA 1002,
XPA 2001–70V, and XPA 2001–100V
Half-Rack 2-Channel and Mono Channel
Audio Power Amplifiers
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
Extron EMEA
Extron Asia
Extron Japan
Extron China
Extron Middle East
+800.633.9876
+800.3987.6673
+800.7339.8766
+81.3.3511.7655
+81.3.3511.7656 FAX
+400.883.1568
+971.4.2991800
+971.4.2991880 FAX
+1.919.863.1794
+1.919.863.1797 FAX
+31.33.453.4040
+31.33.453.4050 FAX
+65.6383.4400
+65.6383.4664 FAX
Inside USA / Canada Only
Inside Europe Only
Inside Asia Only
© 2008 Extron Electronics. All rights reserved.
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
68-1351-01 Rev. A
10 08
Precautions
English
Important Safety
Instructions
C This symbol is intended to alert the
user of important operating and maintenance
(servicing) instructions in the literature provided
with the equipment.
W This symbol is intended to alert the user
of the presence of uninsulated dangerous voltage
within the product’s enclosure that may present a
risk of electric shock. On the product, risk of shock
may be indicated by this symbol:
10. Protect the power cord from being walked
on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories specified
by the manufacturer.
12. Unplug this apparatus during lightning
storms or when unused for long periods of
time.
13. WARNING: To reduce the risk of fire or
electric shock, do not expose this apparatus
to rain or moisture.
This apparatus shall not be exposed to
dripping or splashing and no objects filled
with liquids, such as vases shall be placed
on the apparatus.
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
14. Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or has
been dropped.
8.
Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
15. WARNING: This apparatus is a Class I
product. This product must be connected
to a MAINS socket outlet with a protective
earthing connection.
Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong is provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
16. The mains plug is used as the disconnect
device and shall remain readily operable.
9.
W
Power sources • This equipment should be operated only from the power source indicated on the
product. This equipment is intended to be used with a main power system with a grounded (neutral)
conductor. The third (grounding) pin is a safety feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all power cords from
the rear of the equipment, or the desktop power module (if detachable), or from the power source
receptacle (wall plug).
Extron’s Warranty
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron Electronics 1001 East Ball Road
Anaheim, CA 92805, USA
Asia:
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Europe, Africa, and the Middle East:
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
Japan:
Extron Electronics, Japan
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or nonExtron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que
la documentation fournie avec le matériel
contient des instructions importantes
concernant l’exploitation et la maintenance
(réparation).
Ce symbole sert à avertir l’utilisateur de
la présence dans le boîtier de l’appareil
de  tensions dangereuses non isolées posant
des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes
les consignes de sécurité et d’exploitation avant
d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de
sécurité afin de pouvoir les consulter à l’avenir.
Respecter les avertissements • Observer tous les
avertissements et consignes marqués sur le matériel
ou présentés dans la documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de
pièces de fixation ni d’outils non recommandés par
le fabricant du matériel car cela risquerait de poser
certains dangers.
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im
Lieferumfang enthaltenen Dokumentation
besonders wichtige Hinweise zur Bedienung
und Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer
darauf aufmerksam machen, daß im
Inneren des Gehäuses dieses Produktes
gefährliche Spannungen, die nicht
isoliert sind und die einen elektrischen
Schock verursachen können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum
ersten Mal verwenden, sollten Sie alle Sicherheitsund Bedienungsanleitungen genau durchlesen und
verstehen.
Aufbewahren der Anleitungen • Die Hinweise
zur elektrischen Sicherheit des Produktes sollten
Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle
Warnhinweise und Anleitungen auf dem Gerät oder
in der Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge
oder Zusatzgeräte, die nicht ausdrücklich vom
Hersteller empfohlen wurden, da diese eine
Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al
usuario sobre instrucciones importantes
de operación y mantenimiento (o cambio
de partes) que se desean destacar en el
contenido de la documentación suministrada
con los equipos.
Este símbolo se utiliza para advertir al
usuario sobre la presencia de elementos
con voltaje peligroso sin protección aislante,
que puedan encontrarse dentro de la caja
o alojamiento del producto, y que puedan
representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las
instrucciones de operación y seguridad, antes de usar
el equipo.
Conservar las instrucciones • Conservar las
instrucciones de seguridad para futura consulta.
Obedecer las advertencias • Todas las advertencias
e instrucciones marcadas en el equipo o en la
documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o
accesorios que no sean especificamente recomendados
por el fabricante, ya que podrian implicar riesgos.
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la
source d’alimentation indiquée sur l’appareil. Ce matériel
doit être utilisé avec une alimentation principale comportant
un fil de terre (neutre). Le troisième contact (de mise à la
terre) constitue un dispositif de sécurité : n’essayez pas de la
contourner ni de la désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel
hors tension sans danger, déconnectez tous les cordons
d’alimentation de l’arrière de l’appareil ou du module
d’alimentation de bureau (s’il est amovible) ou encore de la
prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons
d’alimentation de manière à ce que personne ne risque de
marcher dessus et à ce qu’ils ne soient pas écrasés ou pincés
par des objets.
Réparation-maintenance • Faire exécuter toutes les
interventions de réparation-maintenance par un technicien
qualifié. Aucun des éléments internes ne peut être réparé
par l’utilisateur. Afin d’éviter tout danger d’électrocution,
l’utilisateur ne doit pas essayer de procéder lui-même à ces
opérations car l’ouverture ou le retrait des couvercles risquent
de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des
fentes ou des orifices, ceux-ci servent à empêcher les
composants internes sensibles de surchauffer. Ces ouvertures
ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment
incorrect de la batterie. Remplacer uniquement avec une
batterie du meme type ou d’un ype equivalent recommande
par le constructeur. Mettre au reut les batteries usagees
conformement aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem
Produkt angegebene Stromquelle betrieben werden.
Dieses Gerät wurde für eine Verwendung mit einer
Hauptstromleitung mit einem geerdeten (neutralen) Leiter
konzipiert. Der dritte Kontakt ist für einen Erdanschluß,
und stellt eine Sicherheitsfunktion dar. Diese sollte nicht
umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom
Netz zu trennen, sollten Sie alle Netzkabel aus der Rückseite
des Gerätes, aus der externen Stomversorgung (falls dies
möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt
werden, daß sie nicht im Weg liegen und niemand darauf
treten kann oder Objekte darauf- oder unmittelbar
dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von
qualifiziertem Servicepersonal durchgeführt werden. Die
internen Komponenten des Gerätes sind wartungsfrei. Zur
Vermeidung eines elektrischen Schocks versuchen Sie in
keinem Fall, dieses Gerät selbst öffnen, da beim Entfernen
der Abdeckungen die Gefahr eines elektrischen Schlags
und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder
Löcher im Gehäuse aufweist, dienen diese zur Vermeidung
einer Überhitzung der empfindlichen Teile im Inneren. Diese
Öffnungen dürfen niemals von anderen Objekten blockiert
werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht
richtig ersetzt wird. Ersetzen Sie verbrauchte Batterien
nur durch den gleichen oder einen vergleichbaren
Batterietyp, der auch vom Hersteller empfohlen wird.
Entsorgen Sie verbrauchte Batterien bitte gemäß den
Herstelleranweisungen.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse
únicamente a la fuente/tipo de alimentación eléctrica
indicada en el mismo. La alimentación eléctrica de este
equipo debe provenir de un sistema de distribución general
con conductor neutro a tierra. La tercera pata (puesta a tierra)
es una medida de seguridad, no puentearia ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar
con seguridad la acometida de alimentación eléctrica al
equipo, desenchufar todos los cables de alimentación en
el panel trasero del equipo, o desenchufar el módulo de
alimentación (si fuera independiente), o desenchufar el cable
del receptáculo de la pared.
Protección del cables de alimentación • Los cables de
alimentación eléctrica se deben instalar en lugares donde no
sean pisados ni apretados por objetos que se puedan apoyar
sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios
técnicos de personal calificado. En el interior no hay partes
a las que el usuario deba acceder. Para evitar riesgo de
electrocución, no intentar personalmente la reparación/
mantenimiento de este equipo, ya que al abrir o extraer las
tapas puede quedar expuesto a voltajes peligrosos u otros
riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios
en su caja/alojamiento, es para evitar el sobrecalientamiento
de componentes internos sensibles. Estas aberturas nunca se
deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería
se coloca en la posición incorrecta. Cambiar esta batería
únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas
siguiendo las instrucciones del fabricante.
Table of Contents
安全须知 • 中文
警告
Chapter One • Introduction ................................................... 1-1
这个符号提示用户该设备用户手册中
有重要的操作和维护说明。
电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备
必须使用有地线的供电系统供电。 第三条线
(地线)是安全设施,不能不用或跳过。
About this Manual..................................................................... 1-2
这个符号警告用户该设备机壳内有暴
拔掉电源 • 为安全地从设备拔掉电源,请拔掉所有设备后
或桌面电源的电源线,或任何接到市电系统的电源线。
Features......................................................................................... 1-2
露的危险电压,有触电危险。
电源线保护 • 妥善布线, 避免被踩踏,或重物挤压。
注意
阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理
解所有安全和使用说明。
保存说明书 • 用户应保存安全说明书以备将来使
用。
遵守警告 • 用户应遵守产品和用户指南上的所有安
全和操作说明。
维护 • 所有维修必须由认证的维修人员进行。 设备内部
没有用户可以更换的零件。为避免出现触电危险不要自
己试图打开设备盖子维修该设备。
通风孔 • 有些设备机壳上有通风槽或孔,它们是用来防止
机内敏感元件过热。 不要用任何东西挡住通风孔。
锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用
与厂家推荐的相同或相近型号的电池。 按照生产厂的
建议处理废弃电池。
避免追加 • 不要使用该产品厂商没有推荐的工具或
追加设备,以避免危险。
Terms used in this manual...................................................... 1-2
Chapter Two • Installation ...................................................... 2-1
Application Examples. .............................................................. 2-2
Mounting the XPA 1002 and XPA 2001............................... 2-3
Tabletop use............................................................................ 2-3
UL rack mounting guidelines................................................. 2-3
Rack mounting........................................................................ 2-4
Rack mounting ventilation recommendations......................2-5
Flexible conduit adapter kit installation............................... 2-6
FCC Class B Notice
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
the interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
N
Installing the flexible conduit kit...........................................2-7
Chapter Three • Operation ..................................................... 3-1
Front Panel Features and Operation.................................... 3-2
Rear Panel Features and Operation..................................... 3-4
Remote volume control........................................................ 3-11
Bridged mono output........................................................... 3-11
Appendix A • Reference ...........................................................A-1
Specifications...............................................................................A-2
Included Parts..............................................................................A-6
Optional Accessories.................................................................A-7
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used
with the unit to ensure compliance.
XTRA Series • Table of Contents
TOC-i
Table of Contents, cont’d
XTRA Series
1
Chapter One
Introduction
About this Manual
Features
All trademarks mentioned in this manual are the properties of their respective owners.
68-1351-01 Rev. A
10 08
TOC-ii XTRA Series • Table of Contents
Introduction
About this Manual
This manual contains information about the Extron's XTRA
Series of power amplifiers: the XPA 1002 two-channel stereo
audio power amplifier and the XPA 2001 mono audio power
amplifier. The XPA 1002 outputs 60 watts per channel at 8 ohms
and 100 watts per channel at 4 ohms. The XPA 2001 offers two
models: the XPA 2001-70V and the XPA 2001-100V. The XPA
2001-70V outputs 200 watts (70 V line mono), and the XPA 2001100V outputs 200 watts (100 V line mono).
Terms used in this manual
The terms “amplifier” and “power amplifier” are used
interchangeably in this manual to refer to all of the XPA
models. XPA 2001 refers to both the XPA 2001-70V and the XPA
2001-100V.
Features
Inputs — Balanced or unbalanced stereo on a captive screw
connector.
Speaker Outputs — Screw-lock, 5 mm captive screw connector.
Continuous power output for larger rooms —
• XPA 1002: 60 watts rms per channel at 8 ohms; 100
watts rms per channel at 4 ohms.
• XPA 2001-70V: 200 watts rms for 70 volt speaker
systems.
• XPA 2001-100V: 200 watts rms for 100 volt speaker
systems.
Professional grade amplifier design —
• Less than 0.05% Total Harmonic Distortion plus Noise
• Better than 100 dB Signal-to-Noise
ENERGY STAR® qualified amplifier — The XTRA Series of
amplifiers are energy efficient products to help meet green
building requirements for low power consumption and
reduced operating costs.
Highly efficient Class D amplifier design — The XTRA
Series of amplifiers generate substantially less heat than
conventional amplifier designs, making them ideal for
installation in equipment racks and lecterns with very
limited ventilation. They consumes 10 watts when idle
and less than 1 watt in standby mode.
1-2
XTRA Series • Introduction
Extron Patented CDRS™ - Class D Ripple Suppression
— A patented, exclusive technology from Extron that
eliminates the high frequency switching ripple and EMI
emissions found in typical Class D amplifiers. CDRS
enables Extron power amplifiers to be situated near
wireless A/V devices without RF interference.
Convection cooled — The XTRA Series of amplifiers are
convection cooled without the need for fans, ensuring
quiet, reliable operation.
Plenum rated when used with optional Flexible Conduit
Adapter Kit, part # 70-228-02 — The amplifiers meet UL
2043 for smoke and heat release for installation within a
plenum airspace above a drop ceiling.
Auto-standby with fast power-up — The amplifiers
automatically enter into a standby mode after one hour of
inactivity, dramatically reducing power consumption. It
quickly returns to full power status upon signal detection.
Rear panel level controls — Provide attenuation of input
signals for setting proper audio system gain staging
as well as two-zone applications. They are located on
the rear panel to prevent unauthorized or accidental
tampering of the level adjustments.
Multiple protection circuits — Activate during excessive
clipping, thermal overload, or DC faults to prevent
damage to the amplifier and speakers.
Remote standby port — Enables the amplifiers to be remotely
powered down when not in use, reducing operating cost.
Remote volume and mute control port — This port allows the
amplifiers to be remotely controlled using the optional
Extron VCM 100 Series volume and mute or VC 50
volume controllers.
Screw lock, 5 mm captive screw speaker connectors — Enables
simple, secure connections with 22 to 14 AWG speaker
cables.
Front and rear-mounted signal and protection indication LEDs
— Provide convenient indication of amplifier operation
from both sides of an equipment rack.
Internal international power supply — The 100-240VAC, 50-60
Hz, universal power supply provides worldwide power
compatibility.
XTRA Series • Introduction
1-3
Introduction, cont’d
XTRA Series
2
Chapter Two
Installation
Application Examples
Mounting the XPA 1002 and XPA 2001
1-4
XTRA Series • Introduction
Installation
W Installation and service must be performed
Extron
XPA 2001
by authorized personnel only. See “UL rack
mounting guidelines”, on the following page.
Audio Power
Amplifier
A
HP
01
10
Extron
SI 26CT
ING
2 WIR
SS
CLA T
TPU
OU70V
Application Examples
OTE
REM
E
W
MUT
UTS
INP
US
T
17T
EO
TED
LIS /VID S
DIO ATU
AU PAR LEVEL
AP
O)
HFP
80
100
VOL/
10V
R
DBY
STAN
L(MON
Hz
Two-way Ceiling
Speakers
C
0
The following illustrations are application examples for the
XPA 1002 and the XPA 2001.
R/
ITE T
LIMTEC
PRO NAL
0Hz
, 50-6
1.3A
SIG
240V
100-
Remote Monitoring
and Control
TCP/IP
Network
Extron
SI 28
Extron
XPA 1002
Surface-mount
Speakers
Audio Power
Amplifier
2
A
HP
50
Extron
MPX 423
Media Presentation
Matrix
2
-23
RS
LE
RIB
VA
O
IDE
S-V
ING
2 WIR
SS T
CLA TPU 2
OU
1
1
1
2
L
50W
E
MUT
T
17T
EO
TED
LIS /VID S EL 2
DIO ATU LEV
AU AR
APP
EO
VID
x2
OTE
REM
4/8
VOL/
10V
UTS
INP
US
OHM
L
ER
UT
MP
CO
DBY
STAN
L
0
T
OU
C
2
1
0
R/
ITE T
LIMTEC
PRO NAL
SIG
0Hz
, 50-6
1.3A
240V
O IN
IDE
S-V 11
100-
T
OU
T
OU
IN
2
9
I
N
P
U
T
S
L
L
1
2
R
L
3
4
L
R
L
1
2
R
L
L
3
4
R
L
1
2
R
L
3
4
R
R
3
4
R
R
O
U
T
P
U
T
S
C
O
N
T
T
SE
RE
R
K
LIN
O
L ACT
R
R
R
R
Video
R
12
1
EO
VID 7
ER
UT
MP
CO
1
O
I
U L
N
T
P
P
L
U
U
T
T
S
S
S-video
10
2
5
8
6
1
ER
UT
MP
CO
V
-240
100
0.3A
1
IN
3
VGA
2
4
Video
2
0 Hz
50/6
RS-232
Control
S-video
PC (2)
Projector
VGA
UT
TP
OU
A
B
L
R
L
6
DIO3
T
INPU 4
5
8
R
7
AU
Plasma Monitor
2
1
UT
TP
L
OU
ED
LIST
1T23.
U S I.T.E
Y,
B
RG, R-Y
B-Y
R
C
6
I
B
DV
RG
DVD (4)
7
B
RG
3 YC
R-Y
1 VID
0Hz
B-Y
I
50-6
240V
Extron
IN1508
N
P
U
5
Y
VID
100-
4
2
T
Laptop (2)
Scaling Presentation
Switcher
LCD Projector
PC
DVI Input
Laptop
VCR
Document
Camera
DVD Player
PC
XPA 1002 application example
VCR (4)
XPA 2001 Series application example
Mounting the XPA 1002 and XPA 2001
The XPA 1002 and XPA 2001 audio amplifiers can be set on a
table; mounted on a rack shelf; or mounted in the plenum space
above a ceiling-mounted projector.
Tabletop use
Four self-adhesive rubber feet are included with the audio
amplifier.
For tabletop use, attach one foot at each corner of the bottom
side of the unit and place the unit in the desired location.
UL rack mounting guidelines
The following Underwriters Laboratories (UL) guidelines
pertain to the safe installation of the equipment in a rack.
2-2
XTRA Series • Installation
XTRA Series • Installation
2-3
Installation, cont’d
1.
Elevated operating ambient temperature — If installed
in a closed or multi-unit rack assembly, the operating
ambient temperature of the rack environment may be
greater than room ambient temperature. Therefore, install
the equipment in an environment compatible with the
maximum ambient temperature (Tma = +122 °F, +50 °C)
specified by Extron.
2.
Reduced air flow — Install the equipment in a rack so that
the amount of air flow required for safe operation of the
equipment is not compromised.
3.
Mechanical loading — Mount the equipment in the rack
so that a hazardous condition is not achieved due to
uneven mechanical loading.
4.
Circuit overloading — Connect the equipment to
the supply circuit and consider the effect that circuit
overloading might have on overcurrent protection and
supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this
concern.
5.
Reliable earthing (grounding) — Maintain reliable
grounding of rack-mounted equipment. Pay particular
attention to supply connections other than direct
connections to the branch circuit (e.g. use of power strips).
1U Universal Rack Shelf
1/2 Rack Width Front False
Faceplate
Front false
faceplate
uses 2
screws.
(2) 4-40 x 3/16"
Screws
NOTE: Using screws longer
than 3/16” will damage the
unit and void the warranty.
Use 2 mounting holes on
opposite corners.
Rack mounting of the amplifier
4.
Attach the false front panel (provided with rack shelf part
#60-190-01) to the unoccupied side of the rack (as shown
above), or install a second half-rack-width device in that
side by repeating steps 1 through 3.
5.
Attach the rack shelf to the rack using four 10-32 x ¾" bolts
(provided). Insert the bolts through #10 beveled washers,
then through the holes in the rack, as shown above.
Rack mounting
The XPA 1002 or XPA 2001 can be mounted in a rack shelf using
the optional RSU 129 1U Universal rack shelf (Extron part
#60-190-01) or the 1U Basic rack shelf (Extron part #60-604-01),
as follows.
2-4
1.
If feet were installed on the bottom of the amplifier,
remove them.
2.
Place the amplifier on one half of the rack shelf. Align the
front of the amplifier with the front of the shelf, and align
the threaded holes on the bottom of the amplifier with the
holes in the rack shelf.
3.
Attach the amplifier to the rack shelf with the two
provided 4-40 x 3/16” machine screws. Insert the screws
from the underside of the shelf, and securely fasten them
into diagonally-opposite corners.
See the following illustration.
XTRA Series • Installation
Rack mounting ventilation recommendations
Excessive heat can decrease the optimal lifetime of the power
amplifier. An over temp indicator LED on the front panel of
the amplifier lights red whenever the recommended ambient
temperature has been exceeded (see "Front Panel Features and
Operation" in chapter 3).
To reduce the chances for an over temp condition, the XPA(s)
should be arranged in a rack environment so that adequate
airflow is available both above and below the XPA whenever
possible. No more than two XPAs should be arranged oneon-top-of-the-other in a rack without an open space between
them, as shown in the following illustration. An XPA can also
be arranged above or below another non-XPA device, but there
must be an open space both above and below those devices.
XTRA Series • Installation
2-5
Installation, cont’d
Ven
t
Ven
t
Ven
t
Ven
t
The kit provides a convenient means to replace the XPA's IEC
power cord with conduit, where required by local codes.
C
Sp
ace
Sp
ace
Ven
t
Sp
ace
Ven
t
Sp
ace
Make sure that the source device and the XPA are
turned off and disconnected from the power source
before you begin.
UL requirements
Sp
ace
Sp
ace
Allow sufficient spacing for adequate ventilation
The Underwriters Laboratories (UL) requirements listed below
pertain to the installation of the flexible conduit onto a XPA 1002
or XPA 2001.
• This unit is not to be used beyond its rated voltage range.
• This unit must be wired to a UL listed distribution box.
N The UL approved electrical distribution box is not included
with either the XPA or the Flexible Conduit Adapter Kit;
the installer is responsible for obtaining and installing the
box.
Flexible conduit adapter kit installation
W
The circuit breaker used for this connection should
be rated no lower than 20 amps and no greater than
30 amps.
W
This unit must be installed in accordance with the
National Electrical Code and with all local codes.
An ALL-POLE MAINS SWITCH with a contact
separation of at least 3 mm in each pole shall be
incorporated in the electrical installation of the
building. The installation shall be carried out in
accordance with all applicable installation rules.
W
Installation and service must be performed by a
qualified electrician only.
C
A UL listed electrical distribution box is
recommended for the termination of the conduit
opposite the XPA. See the following "UL
requirements" section.
Installing the flexible conduit kit
Install flexible conduit to the XPA by following the steps below.
1.
Unplug the IEC power cord from the power amplifier.
2.
Remove the 8 screws from the top and sides of the XPA
and lift off the cover. See the following illustration.
C Electrostatic discharge (ESD) can damage IC chips even though you cannot feel it. You must be electrically grounded before touching anything inside the XPA. A grounding wrist strap is recommended.
The optional Flexible Conduit Adapter Kit (Extron part
#70-228-02) consists of
• One EMT adapter plate
• One 6-foot long electrical conduit
• Three 7.5 feet, 18-gauge spade connector power wires
• One UL rated zip tie wrap
• Three auxiliary crimp style spade connectors designed for
14- to 16-gauge wires
N If needed, Extron recommends using a UL-rated crimp
tool to terminate the spade connectors. One recommended
choice is the Molex crimp tool (Molex part #19285-0008).
2-6
XTRA Series • Installation
XTRA Series • Installation
2-7
Installation, cont’d
Lift Cover Straight Up
Remove (8)
screws
A
XP
02
OTE
G
IN
G
E
SS
UT
LE
1
US
-60H
, 50
1.3A
0V
0-24
z
TT
C
17
D EO
/
TE ID
ER
LIS IO/V TUS MIT CT
D A
LI TE
AU PAR
O
PR NAL
AP
SIG
1
2
1
following illustration shows the location of the hot
(L) and neutral (N) terminals.
IRIN
REM
2W
CLA
L/M
VO
V
10
TS
PU
IN
L
W Ensure that you observe correct wire polarity. The
10
IR
2W
SS T
CLA TPU 2
OU
1
VE
10. Connect the black hot (line) and white neutral wires to
the terminal block on the PCB using the 2 screws that
were removed in step . Use the included zip tie wrap to
secure the two wires together close to the terminals. See
the following illustration.
2
Y
DB
AN
ST
2
Zip-Tie
0
10
3.
LINE
L
NEUTRAL
N
Remove the 2 screws holding the hot (line) and neutral
wires from the terminal block on the PCB.
240V
1.3A
50-6
0H
z
N
Neutral
Terminal (White)
Conduit Nut
EMT Adapter Plate
L
Remove nut
Remove screws
(both sides) to release
IEC connector plate.
4.
Remove the ground wire nut from the grounding stud on
the bottom of the enclosure, as shown above.
5.
Remove the 2 screws from the IEC plate, and remove the
IEC connector plate and the attached wires through the
rear panel of the XPA, as shown above.
6.
Thread the 18-gauge power wires through the length of the
electrical conduit tube.
7.
Install the EMT adapter plate with conduit attached into
the opening from which the IEC connector was removed.
in step 5.
8.
Slide the conduit nut over the bundle of wires exiting the
conduit and onto the conduit itself. Hand tighten the
conduit nut to the conduit.
9.
Attach the EMT adapter plate assembly to the XPA using
the 2 screws that were removed in step 5.
XTRA Series • Installation
Hot
Terminal (Black)
Ground
Wire Nut
Blue Wire
Brown Wire
100-
2-8
Terminal Block
0
11. Connect the ground wire, as shown above, to the
grounding stud on the bottom of the enclosure using the
nut that was removed in step 4.
12. Replace the cover of the XPA by attaching the 8 screws that
were removed in step 2.
XTRA Series • Installation
2-9
Installation, cont’d
XTRA Series
3
Chapter Three
Operation
Front Panel Features and Operation
Rear Panel Features and Operation
2-10
XTRA Series • Installation
Operation
Front Panel Features and Operation
2
1
OVER
TEMP
XPA 1002
Front Panel
1
1
LIMITER/PROTECT
• When the output wiring is shorted together
• When audio clipping occurs, the corresponding channel’s
LED blinks once per clip occurrence.
• When the amplifier overheats, both LEDs are lit. The LEDs
are not lit after the amplifier recovers from the overheated
condition.
• When DC output is detected, the amplifier is malfunctioning
and the LED for the corresponding channel is lit. The
amplifier requires servicing when this event occurs.
2
LIMITER/PROTECT
SIGNAL
XPA 1002
4a
2 3b
1
a
N These LEDs are also located on the rear panel.
OVER
TEMP
XPA 2001-70V,
XPA 2001-100V
Front Panel
LIMITER/PROTECT
SIGNAL
XPA 2001
Ö
Power indicator LED — This LED lights:
• Green when the amplifier is receiving full power.
• Amber when the amplifier is in Standby mode. Standby
mode turns off all outputs from the amplifier, although the
amplifier is still receiving power.
Over Temp indicator LED — This LED lights red when the
amplifier exceeds the recommended ambient temperature for
optimal lifetime. The LED will turn off after the amplifier has
cooled down sufficiently.
Limiter/Protect indicator LED — This LED (representing the
output channel) lights red under four circumstances:
• When the output wiring is shorted together
• When audio clipping occurs, the LED blinks once per clip
occurrence.
• When the amplifier overheats, the LED is lit. The LED is not
lit after the amplifier recovers from the overheated condition.
• When DC output is detected, the amplifier is malfunctioning
and the LED is lit. The amplifier requires servicing when this
event occurs.
4b
See f of “Rear Panel Features” in this chapter.
b
2
3a
N This LED is also located on the rear panel.
Ü
Signal indicator LEDs (channels 1 and 2) — These LEDs
(representing input channels 1 and 2) light green only when an
input signal is detected on the corresponding channel.
1
2
Should the LED light, check the following:
• Verify that the placement of the amplifier allows for adequate
ventilation and airflow.
• Avoid placing other equipment on top of the amplifier.
• Verify that the operating temperature is within the specified
range.
Ñ
3-2
Limiter/Protect indicator LEDs (channels 1 and 2) — These
LEDs (representing output channels 1 and 2) light red under
four circumstances:
XTRA Series • Operation
SIGNAL
N These LEDs are also located on the rear panel.
á
Signal indicator LED — This LED (representing the input
channel) lights green only when an input signal is detected.
N This LED is also located on the rear panel.
XTRA Series • Operation
3-3
Operation, cont’d
Rear Panel Features and Operation
• When the amplifier overheats, both LEDs are lit. The LEDs
are not lit after the amplifier cools down and recovers from
the overheated condition.
• When DC output is detected, the amplifier is malfunctioning
and the LED for the corresponding channel is lit. When a
malfunction occurs, power down the amplifier and power it
back up. If the LED still remains lit, the amplifier requires
servicing.
2a
100-240V
0.5A, 50-60Hz
C
1
US
LIMITER/
PROTECT
1
XPA 1002
LISTED 17TT
AUDIO/VIDEO
APPARATUS
LEVEL
2
SIGNAL
CLASS 2 WIRING
INPUTS
2
1
0
REMOTE
10V
2
1
OUTPUT
1
2
50 mA
VOL/MUTE
0
STANDBY
XPA 1002
Rear Panel
3a
4
5a
6
See step Ñ of "Front Panel Features and Operation" in this
chapter.
7a
2b
100-240V
XPA 2001-70V
0.5A, 50-60Hz
C
1
US
LISTED 17TT
AUDIO/VIDEO
APPARATUS
LEVEL
CLASS 2 WIRING
HFP
INPUTS
REMOTE
10V
80 Hz
LIMITER/
PROTECT
SIGNAL
L(MONO)
R
50 mA
VOL/MUTE
3b 4
8
STANDBY
5b
6
INPUTS
REMOTE
7b
2b
100-240V
XPA 2001-100V
0.5A, 50-60Hz
C
1
US
LISTED 17TT
AUDIO/VIDEO
APPARATUS
LEVEL
CLASS 2 WIRING
HFP
10V
80 Hz
LIMITER/
PROTECT
SIGNAL
L(MONO)
R
50 mA
VOL/MUTE
a
Ç
OUTPUT
100 V
0
OFF
XPA 2001-100V
Rear Panel
3b 4
8
5b
6
7b
Ñ
1
2
XTRA Series • Operation
Signal indicator LEDs (channels 1 and 2) — These LEDs
(representing input channels 1 and 2) light green only when an
input signal is detected on the corresponding channel.
1
2
SIGNAL
Limiter/Protect indicator LEDs (channels 1 and 2) — These
LEDs (representing output channels 1 and 2) light red under
four circumstances:
• When the output wiring is shorted together
• When audio clipping occurs, the corresponding channel’s
LED blinks once per clip occurrence.
3-4
See step Ö of "Front Panel Features and Operation" in this
chapter.
STANDBY
AC power connector — Connect a standard IEC AC power cord
here for power input (100 VAC to 240 VAC, 50/60 Hz) to the
internal, autoswitching power supply. This connector may be
replaced by the PS 123 Flexible Conduit Adapter Kit (part
#70-228-02) as described in "Flexible conduit adapter kit
installation" in chapter 2.
LIMITER/
PROTECT
Limiter/Protect indicator LED — This LED (representing the
output channel) lights red under four circumstances:
• When the output wiring is shorted together
• When audio clipping occurs, the LED blinks once per clip
occurrence.
• When the amplifier overheats, the LED is lit. The LED is
not lit after the amplifier cools down and recovers from the
overheated condition.
• When DC output is detected, the amplifier is malfunctioning
and the LED is lit. When a malfunction occurs, power down
the amplifier and power it back up. If the LED still remains
lit, the amplifier requires servicing.
0
OFF
XPA 2001-70V
Rear Panel
É
OUTPUT
70 V
See step Ü of "Front Panel Features and Operation" in this
chapter.
Ö
d
Signal indicator LED — This LED (representing the input
channel) lights green only when an input signal is detected.
Level adjustment (channels 1 and 2) — Use a Tweeker or
small screwdriver to adjust the audio input level for the
corresponding channel. The analog potentiometers control the
level from -= (full attenuation) to 0 dB.
XTRA Series • Operation
3-5
Operation, cont’d
N On the XPA 2001, the single control adjusts the levels
2.
Set the source device's volume to its maximum volume
level. No sound should come out.
3.
Return to the XPA amplifier and raise the level(s) until
sound distortion occurs, then lower the level(s) slightly
until any distortion disappears. This setting ensures that,
whatever the source device volume setting may be, no
clipping occurs.
Unbalanced Mono Input
f
Remote control connector — The 3.5 mm 5-pin captive screw
receptacle is used to remotely control two functions through
contact closure: See the following circuit diagram.
10V
à
Balanced or unbalanced stereo audio input connector — Wire
the 3.5 mm 5-pin captive screw connector for balanced or
unbalanced input.
Balanced Stereo Input
3
STANDBY
1 10 V
MAX
MUTE
2K OHMS
10K OHMS
MIN
Do not tin the wires!
2
R
R
Unbalanced Stereo Input
1
50 mA
VOL/MUTE
L
L
Tip
Sleeve
(high impedance)
• Pins 1, 2, and 3 control volume by varying the DC voltage
from 0 V (full attenuation) to 10 V (maximum volume) with
full muting in effect when pin 2 is connected to ground (pin3).
Use the included 3-pin captive screw connector. See "Remote
volume control" in this chapter.
ensure that the device's volume is set to variable out.
Consult the device's user manual for detailed instructions
on its calibration.
Tip
Ring
Sleeves
Tip
Ring
Balanced Mono Input
Do not tin the wires!
N When setting volume control through a source device,
Tip
Sleeve
R
If connecting to a source device with a volume control
(variable output), ensure that the volume on the source
device is set to its lowest point, then adjust the level(s) of
the XPA fully counterclockwise.
Tip
Ring
Sleeves
Tip
Ring
L
1.
Tip
Sleeve
R
To adjust the XPA amplifier's input level, do the following:
Tip
Sleeve
L
of both channels simultaneously prior to summing them
together.
2 VOL/MUTE
MUTE SWITCH
VOLUME
3 GND
N The XPA 1002's output power can be effectively doubled
by using only one input channel and bridging the output.
The XPA 1002 will output 200 watts @ 8 ohms or 120
watts @ 16 ohms in bridged mode.
See "Bridged mono output" in this chapter for wiring
instructions when bridging the XPA 1002.
â
3-6
Balanced or unbalanced mono audio input connector — Wire
the 3.5 mm 5-pin captive screw connector for balanced or
unbalanced input.
XTRA Series • Operation
XTRA Series • Operation
3-7
Operation, cont’d
• Pin 5 connected to ground (pin 4) places the amplifier in
standby mode. Standby mode turns off all output, although
the amplifier is still receiving power. Use the included 2-pin,
3.5 mm captive screw connector to remotely ground pin 5.
The power indicator LED lights amber when the amplifier is
in standby mode.
10V
Step 1: Strip and insert the speaker wires into the connector and
tighten the captive screws. Be sure to observe the
correct polarity.
Do not tin the wires!
50 mA
VOL/MUTE
1
2
4
5
5
STANDBY
4
3
3
2
STANDBY
1
Step 2: Insert the wired connector into the amplifier output
and secure the locking screws on either side.
Remote Switching to Standby Mode
UT
TP 2
OU
1
å
Stereo audio output connector (channels 1 and 2) — Marked
"1" and "2" for the output channels, wire the included 4-pole,
5 mm screw lock captive screw connector to output stereo audio
through either channel. Observe the correct polarities for each
channel. See the following steps. Output is designed to power 4
or 8 ohm speakers and is rated at 50 watts per channel.
N You must use Class 2 wiring for this output to comply
with UL requirements.
ç
OUTPUT
1
2
Mono audio output connector — Marked "+" and "-", wire
the included 2-pole, 5 mm screw lock captive screw connector
for mono audio. See the following steps. Output is designed
to power 70 V (XPA 2001-70V) or 100 V (XPA 2001-100V) line
distribution systems and is rated at 100 watts.
N You must use Class 2 wiring for this output to comply
W Do not tie channel outputs 1 and 2 to each other or
with UL requirements.
to ground. Doing so will short out the outputs and/
or damage the amplifier.
OUTPUT
70V
OUTPUT
100V
N The XPA 1002's output power can be effectively doubled
by using only one input channel and bridging the output.
The XPA 1002 will output 200 watts @ 8 ohms or 120
watts @ 16 ohms in bridged mode.
See "Bridged mono output" in this chapter for wiring
instructions when bridging the XPA 1002.
3-8
XTRA Series • Operation
XPA 2001-70V
XPA 2001-100V
W Do not short out the "+" and "-" connectors with
each other; doing so will damage the amplifier.
XTRA Series • Operation
3-9
Operation, cont’d
Remote volume control
Step 1: Strip and insert the speaker wires into the connector and
tighten the captive screws. Be sure to observe
correct polarity.
Do not tin the wires!
Options for remote control of the XPA amplifiers include the
Extron VCM 100 and VC 50 volume controllers. Third party 10k
potentiometer volume controllers can also be connected to this
port.
As shown in the following illustration, the XPA's pin 1 is 10
VDC reference voltage. Pin 2 is volume control DC voltage,
range is 0 to 10 V, where 0 V is mute and 10 V provides
maximum volume. Pin 3 is ground.
N All nominal levels are at ±10%.
REMOTE
10V
1
T
Extron
STP 22
Cable
50 mA
VOL/MUTE
2
3
4
5
10V
and secure the locking screws on either side.
Red
Black
Ground
VOL/
MUTE
Step 2: Insert the wired connector into the amplifier output
STANDBY
U
TP
OU70V
VOLUME
MUTE
h
High pass filter toggle switch — Use a Tweeker or small
screwdriver to toggle this recessed two-position toggle switch
that alternates between Off and 80 Hz. Setting the switch to
80 Hz prevents the saturation of 70 V/100 V speaker input
transformers by low frequency signals. Saturation may result in
undesired overheating of the speaker transformers.
N Filtering may be unnecessary if filtering is applied to the
source input signal upstream of the amplifier.
VCM 100
Pinout diagram for VCM 100 MAAP connection to
XPA's remote connector
Bridged mono output
The power output of the XPA 1002 can be effectively doubled by
bridging the output. Bridging allows power to be output at 200
watts @ 8 ohms or 120 watts @ 16 ohms.
N The bridging instructions that follow apply only to the
XPA 1002 model.
N The minimum load impedance when bridging is 8 ohms.
To bridge the output, follow the steps and refer to the diagram
below:
3-10
XTRA Series • Operation
1.
Unplug the IEC power cord from the power amplifier.
2.
Wire the output as shown in the following diagram.
XTRA Series • Operation
3-11
Operation, cont’d
3.
Wire the input as shown in the following diagram.
4.
Adjust the input levels of channels 1 and 2 equally.
Refer to step d (level adjustment) of "Rear Panel Features
and Operation" in this chapter for more details.
100-240V
XPA 1002
LISTED 17TT
0.5A, 50-60Hz
C
XTRA Series
US AUDIO/VIDEO
APPARATUS
LEVEL
LIMITER/
PROTECT
1
2
SIGNAL
INPUTS
2
2
1
0
1
REMOTE
VOL/MUTE
10V
0
STANDBY
Input
Levels should be set
identically.
3.5 mm
Captive Screw
Balanced Wiring
1
From
Mono
Source
2
Un-Balanced Wiring
1
2
From
Mono
Source
OUTPUT
1
2
CLASS 2 WIRING
Amplified
Output
A
Appendix A
Reference
5 mm
Captive Screw
Specifications
1
Included Parts
2
To 8/16 Ohm
Speaker Load
3-12
XTRA Series • Operation
Optional Accessories
Specifications, Part Numbers, and Accessories
Specifications
Audio
Voltage gain
XPA 1002����������������������������� 16x (24 dB)
XPA 2001-70V��������������������� 57x (35 dB)
XPA 2001-100V������������������� 81x (38 dB)
Stereo channel separation������������ >75 dB @ 1 kHz
CMRR���������������������������������������������� 75 dB @ 1 kHz (typical)
Audio input
Number/signal type��������������������� 1 stereo or 2 mono,
balanced/unbalanced
Connectors������������������������������������� (1) 3.5 mm captive screw
connector, 5 pole
Impedance�������������������������������������� >10k ohms unbalanced/
balanced, DC coupled
Nominal level�������������������������������� +4 dBu (1.23 Vrms),
balanced
Maximum level������������������������������ +20 dBu (7.75 Vrms),
balanced
Input sensitivity
XPA 1002����������������������������� +4 dBu (1.23 Vrms)
XPA 2001-70V, XPA-2001-100V
+4 dBu (1.23 Vrms) if driven
by one input
-2 dBu (0.615 Vrms) if both
inputs are summed
N 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms,
0 dBV ≈ 2 dBu
Audio output
Number/signal type
XPA 1002����������������������������� 1 stereo, 4- or 8-ohm direct
XPA 2001-70V��������������������� 1 mono, 70 V line
XPA 2001-100V������������������� 1 mono, 100 V line
Connectors
XPA 1002����������������������������� (1) 5 mm screw lock captive
screw connector, 4 pole
XPA 2001-70V, XPA-2001-100V
(1) 5 mm screw lock captive
screw connector, 2 pole
Minimum load impedance
XPA 1002����������������������������� 4 ohms
A-2
XTRA Series • Reference
XPA 2001-70V��������������������� 50 ohms
XPA 2001-100V������������������� 100 ohms
Amplifier type������������������������������� Class D
Output power
XPA 1002����������������������������� 60 watts rms per channel,
8 ohms, 1 kHz, <0.05% THD
100 watts rms per channel,
4 ohms, 1 kHz, <0.05% THD
XPA 2001-70V��������������������� 200 watts rms, 70 V,
1 kHz, <0.1% THD
XPA 2001-100V������������������� 200 watts rms, 100 V,
1 kHz, <0.1% THD
Frequency response���������������������� 20 Hz to 20 kHz, ±1 dB
THD + Noise
XPA 1002����������������������������� 0.05% @ 20 Hz-20 kHz,
8 ohms, at 3 dB below
clipping
XPA 2001-70V, XPA-2001-100V
<0.1% @ 1 kHz at 3 dB
below clipping
S/N�������������������������������������������������� >100 dB
Damping factor
XPA 1002����������������������������� >100 @ 8 ohms
High pass filter
XPA 2001-70V, XPA-2001-100V
80 Hz, 12 dB per octave
rolloff (switch selectable)
Control/remote — amplifier
Control port������������������������������������ (1) 3.5 mm captive screw
connector, 5 pole
Pin configurations
DC volume control (analog) Pin 1 = +10 VDC, 50 mA
(max.), pin 2 = volume/
mute (variable voltage),
pin 3 = GND
Volume control voltage range
0 V (mute) to 10 V
(maximum volume)
Standby power control (contact closure)
Pin 4 = GND,
pin 5 = standby
XTRA Series • Reference
A-3
Specifications, Part Numbers, Accessories, cont’d
General
Power���������������������������������������������� 100 VAC to 240 VAC,
50/60 Hz, internal
Typical��������������������������������� 26 watts (1/8 power [pink
noise] at 8 ohms)
Quiescent���������������������������� 10 watts
Standby������������������������������� <1 watt (triggered by
contact closure or after 1
hour with no signal)
Temperature/humidity���������������� Storage: -40 to +158 °F
(-40 to +70 °C) / 10% to
90%, noncondensing
Operating: +32 to +122 °F
(0 to +50 °C) / 10% to 90%,
noncondensing
Cooling������������������������������������������� Convection, no vents, with
internal heat sinks
Thermal dissipation
Standby������������������������������� <1 watt (3 BTU/hr)
Idle��������������������������������������� 10 watts (34 BTU/hr)
1/8 power (pink noise)����� 4 ohms (x2): 14 watts
8 ohms (x2): 14 watts
(48 BTU/hr)
70 V (XPA 2001-70V):
14 watts (48 BTU/hr)
Protection��������������������������������������� Clip limiting, thermal, short
circuit, DC output
Indication��������������������������������������� Limiter/Protect LED
indicates the onset of clip
limiting, thermal cycling,
short circuit, or DC output
protection
Mounting
Rack mount������������������������ Yes, with optional 1U, 9.5"
deep rack shelf (RSU 129,
#60-190-01; RSB 129, #60-604-01)
Enclosure type������������������������������� Metal
Enclosure dimensions������������������� 1.7" H x 8.7" W x 9.5" D
(1U high, half rack wide)
(4.3 cm H x 22.1 cm W x
24.1 cm D)
Product weight������������������������������ 2.5 lbs (1.1 kg)
A-4
XTRA Series • Reference
Shipping weight���������������������������� 5 lbs (3 kg)
Vibration����������������������������������������� ISTA 1A in carton
(International Safe Transit
Association)
Regulatory compliance
Safety����������������������������������� CE, C-tick, CUL, UL
UL rated for use in plenum
airspaces: meets UL 2043
for heat and smoke release;
meets UL 60065, IEC 60065,
and BSEN 60065 for A/V
equipment.
EMI/EMC�������������������������� CE, CISPR 22 Class B,
C-tick, FCC Class B, ICES,
VCCI Class B
Environmental������������������� Complies with the
appropriate requirements
of CEC, ENERGY STAR®
(ENERGY STAR® qualified
amplifier), EU code of
conduct, RoHS, WEEE
MTBF����������������������������������������������� 250,000 hours
Warranty����������������������������������������� 3 years parts and labor
N All nominal levels are at ±10%.
N Specifications are subject to change without notice.
XTRA Series • Reference
A-5
Specifications, Part Numbers, Accessories, cont’d
Included Parts
Optional Accessories
These items are included in each order of the XPA 1002 or
XPA 2001-70V.
Included parts
XPA 1002 two-channel power
amplifier
Replacement part
number
60-849-01
or
XPA 2001-70V single-channel
power amplifier
60-850-01
or
XPA 2001-100V singlechannel power amplifier
60-850-11
(1) 4-pole screw lock
5.08 mm captive screw plug
(XPA 1002)
10-760-10LF
(1) 2-pole screw lock
5.08 mm captive screw plug
(XPA 2001-70V/100V)
10-760-11LF
(1) 5-pole 3.5 mm captive
screw plug
10-703-12LF
(1) 3-pole 3.5 mm captive
screw plug
10-703-11LF
(1) 2-pole 3.5 mm captive
screw plug
10-703-10LF
Accessory
Part number
RSU 129 9.5" deep 1U universal rack
shelf kit
60-190-01
RSB 129 9.5" deep 1U basic rack shelf
60-604-01
VCM 100 AAP volume and mute control
70-396-11, -21,
-51
VCM 100 MAAP volume and mute
control
70-397-11, -21,
-51
VC 50 volume control wall plate
70-530-02
PS 123 flexible conduit adapter kit
70-228-02
(4) rubber feet (detached)
IEC power cord
User’s manual
A-6
XTRA Series • Reference
XTRA Series • Reference
A-7
Specifications, Part Numbers, Accessories, cont’d
A-8
XTRA Series • Reference
XTRA Series • Reference
A-9
Specifications, Part Numbers, Accessories, cont’d
A-10
XTRA Series • Reference