Fetco Home Decor CBS-31AAP Coffeemaker User Manual

Contents
Before driving
Introduction
2
Instrumentation
4
Controls and features
16
Seating and safety restraints
63
Starting and driving
Starting
83
Driving
88
Roadside emergencies
108
Servicing
Maintenance and care
126
Capacities and specifications
177
Reporting safety defects
185
Index
186
All rights reserved. Reproduction by any means, electronic
or mechanical including photocopying, recording or by any
information storage and retrieval system or translation in
whole or part is not permitted without written
authorization from Ford Motor Company.
Copyright r 1998 Ford Motor Company
1
Introduction
ICONS
Indicates a safety alert.
Read the following
section on Warnings.
Indicates vehicle
information related to
recycling and other
environmental
concerns will follow.
Correct vehicle usage and the authorized disposal of
waste cleaning and lubrication materials are
significant steps towards protecting the
environment.
Indicates a message
regarding child safety
restraints. Refer to
Seating and safety
restraints for more information.
Indicates that this
Owner Guide contains
information on this
subject. Please refer to
the Index to locate the appropriate section which
will provide you more information.
WARNINGS
Warnings provide information which may reduce the
risk of personal injury and prevent possible damage
to others, your vehicle and its equipment.
BREAKING-IN YOUR VEHICLE
There are no particular breaking-in rules for your
vehicle. During the first 1 600 km (1 000 miles) of
driving, vary speeds frequently. This is necessary to
give the moving parts a chance to break in.
2
Introduction
INFORMATION ABOUT THIS GUIDE
The information found in this guide was in effect at
the time of printing. Ford may change the contents
without notice and without incurring obligation.
SPECIAL NOTICES
Notice to owners of Cobra vehicles
Before you drive your vehicle, be sure to read the
“SVT Cobra Owner’s Guide Supplement.” This book
contains important operation and maintenance
information.
3
Instrumentation
Instrument
cluster
(pg. 6)
Headlamp control
(pg. 16)
60
50
40
C
H
30
70 80 90 100
20
10
3
130
220
240
20
km/h
MPH
150
L
7
0
SELECT/RESET
SERVICE
ENGINE
SOON
H
8
0 0 0 0 0 0 .0
L
F
AIR THEFT
BAG
LOW
FUEL
HI
LO
OFF
4
6
140
REAR DEF
Turn signal and
wiper/washer
control
(pg. 43)
5
2
1
FUEL DOOR
E
4
RPMX1000
120 140
110
100
160
80
180 120
200
60
40
Driver side air
bag
(pg. 71)
O/D
OFF
ABS
BRAKE
P
!
H
Instrumentation
Electronic
sound system
(pg. 21)
VENT OFF FLOOR
MIX
LO
NORM
A/C
MAX
A/C
HI
FM1
REW
AUTOMATIC
DNR CrO2
ST
FF
PLAY EJCT
PROG
POWER
AUDIO
VOLUME
AM/FM
1
2
3
4
5
CLOCK
AUTO
PRESET
SCAN
TUNE
SEEK
Climate control
systems
(pg. 18)
5
Instrumentation
WARNING LIGHTS AND CHIMES
Base instrument cluster
60 70
50
40
C
H
80 100 120
2
100
160
40
20
RPMX1000
5
SELECT/RESET
7
1
120
MPH
km/h
L
6
180110
20
10
0
H
0 0 0 0 0 0 .0
FUEL DOOR
E
4
3
80
90
140
60
30
F
L
AIR THEFT
BAG
SERVICE
ENGINE
SOON
LOW
FUEL
O/D
OFF
H
BRAKE
!
P
ABS
Optional instrument cluster
60
50
40
C
H
30
70 80 90
60
200
40
220
20
10
130
240
20
MPH
km/h
5
RPMX1000
2
6
1
7
L
H
140
150
0
SELECT/RESET
8
0 0 0 0 0 0 .0
FUEL DOOR
E
4
3
100
120 140
110
100
160
80
180 120
F
L
AIR THEFT
BAG
SERVICE
ENGINE
SOON
LOW
FUEL
O/D
OFF
ABS
H
BRAKE
!
P
Turn signal
Illuminates when the
left or right turn signal
or the hazard lights are
turned on. If one or
both of the indicators stay on continuously or flash
faster, check for a burned-out turn signal bulb. Refer
to Exterior bulbs in the Maintenance and care
chapter.
6
Instrumentation
High beams
Illuminates when the
high beam headlamps
are turned on.
Safety belt
Momentarily illuminates
when the ignition is
turned to the ON
position to remind you
to fasten your safety belts. For more information,
refer to the Seating and safety restraints chapter.
Charging system
Illuminates when the
ignition is turned to
the ON position and
the engine is off. The
light also illuminates when the battery is not
charging properly, requiring electrical system
service.
Air bag readiness
Momentarily
AIR
illuminates when the
BAG
ignition is turned ON.
If the light fails to
illuminate, continues to flash or remains on, have
the system serviced immediately.
Anti-theft system
Refer to SecuriLocky
passive anti-theft
system in the Controls
and features chapter.
THEFT
7
Instrumentation
Service engine soon
Your vehicle is
SERVICE
ENGINE
equipped with a
SOON
computer that monitors
the engine’s emission
control system. This
system is commonly known as the On Board
Diagnostics System (OBD II). The OBD II system
protects the environment by ensuring that your
vehicle continues to meet government emission
standards. The OBD II system also assists the
service technician in properly servicing your vehicle.
The Service Engine Soon indicator light illuminates
when the ignition is first turned to the ON position
to check the bulb. If it comes on after the engine is
started, one of the engine’s emission control systems
may be malfunctioning. The light may illuminate
without a driveability concern being noted. The
vehicle will usually be drivable and will not require
towing.
What you should do if the Service Engine Soon
light illuminates
Light turns on solid:
This means that the OBD II system has detected a
malfunction.
Temporary malfunctions may cause your Service
Engine Soon light to illuminate. Examples are:
1. The vehicle has run out of fuel. (The engine may
misfire or run poorly.)
2. Poor fuel quality or water in the fuel.
3. The fuel cap may not have been properly installed
and securely tightened.
These temporary malfunctions can be corrected by
filling the fuel tank with good quality fuel and/or
properly installing and securely tightening the gas
cap. After three driving cycles without these or any
other temporary malfunctions present, the Service
Engine Soon light should turn off. (A driving cycle
8
Instrumentation
consists of a cold engine startup followed by mixed
city/highway driving.) No additional vehicle service is
required.
If the Service Engine Soon light remains on, have
your vehicle serviced at the first available
opportunity.
Light is blinking:
Engine misfire is occurring which could damage your
catalytic converter. You should drive in a moderate
fashion (avoid heavy acceleration and deceleration)
and have your vehicle serviced at the first available
opportunity.
Under engine misfire conditions, excessive
exhaust temperatures could damage the
catalytic converter, the fuel system, interior floor
coverings or other vehicle components, possibly
causing a fire.
Low fuel
Illuminates as an early
LOW
reminder of a low fuel
condition indicated on
FUEL
the fuel gauge. The
light comes on when there is approximately 1/16th
of a tank indicated on the fuel gauge (refer to Fuel
Gauge in this chapter for more information). The
ignition must be in the ON position for this lamp to
illuminate. The lamp will also illuminate for several
seconds after the ignition is turned to the ON
position regardless of the fuel level.
O/D off (if equipped)
Illuminates when the
O/D
transmission control
OFF
switch has been
pushed. When the light
is on, the transmission does not shift into overdrive.
If the light does not come on when the transmission
9
Instrumentation
control switch is depressed or if the light flashes
when you are driving, have your vehicle serviced.
Traction ControlY active
This light momentarily
illuminates when the
ignition is turned to
ON. It also illuminates
when the Traction Controly system begins applying
and releasing the brakes and adjusting the engine
characteristics to limit a wheelspin condition. It will
be lit for a minimum of four seconds or for the
duration of the Traction Controly event.
For more information, refer to the Driving chapter.
Anti-lock brake system (ABS)
Momentarily illuminates
when the ignition is
ABS
turned to the ON
position and the engine
is off. If the light remains on, continues to flash or
fails to illuminate, have the system serviced
immediately. With the ABS light on, the anti-lock
brake system is disabled and normal braking is still
effective unless the brake warning light also remains
illuminated with parking brake released.
Brake system warning
Momentarily illuminates
BRAKE
when the ignition is
!
P
turned to the ON
position and the engine
is off. If brake warning lamp does not illuminate at
this time, seek service immediately. Also illuminates
when the parking brake is engaged. Illumination
after releasing the parking brake indicates low brake
fluid level and the brake system should be inspected
immediately.
10
Instrumentation
Check coolant
Illuminates when the
coolant level in the
coolant reservoir is low
and more needs to be
added. This lamp will also illuminate when the
ignition is turned to ON and the engine is off. For
more information on adding engine coolant, refer to
Engine coolant in the Maintenance and care
chapter.
Safety belt warning chime
Chimes to remind you to fasten your safety belts.
For information on the safety belt warning chime,
refer to the Seating and safety restraints chapter.
Supplemental restraint system (SRS) warning
chime
For information on the SRS warning chime, refer to
the Seating and safety restraints chapter.
Key-in-ignition warning chime
Sounds when the key is left in the ignition in the
OFF/LOCK or ACC position and the driver’s door is
opened.
Headlamps on warning chime
Sounds when the headlamps or parking lamps are
on, the ignition is off (and the key is not in the
ignition) and the driver’s door is opened.
11
Instrumentation
GAUGES
Base instrument cluster gauges
50
40
C
H
60 70
80 100 120
100
160
40
20
2
RPMX1000
5
SELECT/RESET
7
1
6
180110
20
10
120
MPH
0
km/h
L
H
0 0 0 0 0 0 .0
FUEL DOOR
E
4
3
80
90
140
60
30
F
L
AIR THEFT
BAG
SERVICE
ENGINE
SOON
LOW
FUEL
O/D
OFF
H
BRAKE
!
P
ABS
Optional instrument cluster gauges
60
50
40
H
30
70 80 90
60
200
40
220
20
10
130
240
20
MPH
km/h
4
3
100
5
RPMX1000
120 140
110
100
160
80
180 120
2
6
1
7
L
H
140
150
0
SELECT/RESET
8
0 0 0 0 0 0 .0
FUEL DOOR
F
L
AIR THEFT
BAG
SERVICE
ENGINE
SOON
LOW
FUEL
O/D
OFF
ABS
H
BRAKE
!
P
Fuel gauge
Displays approximately
F
how much fuel is in the
fuel tank (when the
key is in the ON
position). The fuel gauge may vary slightly when the
vehicle is in motion. The ignition should be in the
OFF position while the vehicle is being refueled.
When the gauge first indicates empty, there is a
small amount of reserve fuel in the tank. When
refueling the vehicle from empty indication, the
amount of fuel that can be added will be less than
the advertised capacity due to the reserve fuel.
12
Instrumentation
Engine coolant temperature gauge
Indicates the
C
H
temperature of the
engine coolant. At
normal operating
temperature, the needle remains within the normal
area (the area between the “H” and “C”). If it enters
the red section, the engine is overheating. Stop the
vehicle as soon as safely possible, switch off the
engine immediately and let the engine cool. Refer to
Engine coolant in the Maintenance and care
chapter.
Never remove the coolant reservoir cap
while the engine is running or hot.
This gauge indicates the temperature of the engine
coolant, not the coolant level. If the coolant is not at
its proper level the gauge indication will not be
accurate.
Speedometer
Indicates the current vehicle speed.
• Base instrument
60
cluster
50
40
70
100 120
80
90
140
60
30
20
80
100
160
40
180 110
20
10
120
MPH
km/h
FUEL DOOR
• Optional instrument
cluster
70 80 90 100
50 100120 140 160 110
60
80
40
30
60
180 120
200
130
40
20
10
220
240
20
MPH
km/h
140
150
FUEL DOOR
13
Instrumentation
Odometer
Registers the total
kilometers (miles) of
the vehicle.
4
3
5
RPMX1000
2
6
0
8
1
7
SELECT/RESET
0 0 0 0 0 0 .0
Tachometer
Indicates the engine speed in revolutions per
minute.
Driving with your tachometer pointer at the top of
the scale or in the red zone may damage the engine.
• Base instrument
4
3
cluster
RPMX1000
2
5
1
6
0
SELECT/RESET
7
0 0 0 0 0 0 .0
• Standard instrument
cluster
3
4
5
RPMX1000
6
2
1
7
0
SELECT/RESET
0 0 0 0 0 0 .0
14
8
Instrumentation
Trip odometer
Registers the
kilometers (miles) of
individual journeys.
Press the reset button
until a “T” appears in
the display (this
represents the trip
mode). Press and hold
the button for
2.5 seconds to reset.
3
4
5
RPMX1000
2
6
0
8
1
7
SELECT/RESET
0 0 0 0 0 0 .0
Battery voltage gauge
This gauge shows the
L
H
battery voltage when
the ignition is in the
ON position. If the
pointer moves and stays outside the normal
operating range (as indicated), have the vehicle’s
electrical system checked as soon as possible.
Engine oil pressure gauge
This shows the engine
L
H
oil pressure in the
system. Sufficient
pressure exists as long
as the needle remains in the normal range (the area
between the “L” and “H”).
If the gauge indicates low pressure, stop the vehicle
as soon as safely possible and switch off the engine
immediately. Check the oil level. Add oil if needed
(refer to Engine oil in the Maintenance and care
chapter). If the oil level is correct, have your vehicle
checked at your dealership or by a qualified
technician.
15
Controls and features
HEADLAMP CONTROL
• Pull the headlamp
control toward you
to the first position
to turn on the
parking lamps, tail
lamps, license plate
lamps and marker
lamps.
• Pull the headlamp control toward you to the outer
position to turn on the headlamps (in addition to
the previous lamps).
Daytime running lamps (DRL) (if equipped)
Turns the headlamps on with a reduced output. To
activate:
• the ignition must be turned on
• the headlamp control is in the OFF or Parking
lamps position
• the high beam headlamps must be turned off
• the parking brake is released
Always remember to turn on your
headlamps at dusk or during inclement
weather. The Daytime Running Light (DRL)
System does not activate your tail lamps and
generally may not provide adequate lighting during
these conditions. Failure to activate your
headlamps under these conditions may result in a
collision.
16
Controls and features
PANEL DIMMER CONTROL
To adjust the
brightness of the
instrument panel:
• Rotate clockwise/
counterclockwise
when the headlamp
control is in the
parking lamp or low-beam position.
To turn on the courtesy lamps:
• Rotate fully counterclockwise.
REAR WINDOW DEFROSTER (IF EQUIPPED)
The rear defroster
REAR DEF
control is located on
the instrument panel.
Press the rear defroster control to clear the rear
window of thin ice and fog.
• The small LED will illuminate when the rear
defroster is activated.
The ignition must be in the ON position to operate
the rear window defroster.
The defroster turns off automatically after
10 minutes or when the ignition is turned to the
OFF position. To manually turn off the defroster
before ten minutes have passed, push the control
again.
17
Controls and features
CLIMATE CONTROL SYSTEM
Manual heating and air conditioning system
VENT OFF FLOOR
MIX
LO
NORM
A/C
HI
MAX
A/C
Fan speed control
Controls the volume of
air circulated in the
vehicle.
LO
HI
Temperature control knob
Controls the
temperature of the
airflow inside the
vehicle.
Mode selector control
Controls the direction
of the airflow to the
inside of the vehicle.
VENT OFF FLOOR
MIX
NORM
A/C
MAX
A/C
The air conditioning compressor will operate in all
modes except VENT and FLR. However, the air
conditioning will only function if the outside
temperature is about 10°C (50°F) or above.
Since the air conditioner removes considerable
moisture from the air during operation, it is normal
if clear water drips on the ground under the air
conditioner drain while the system is working and
even after you have stopped the vehicle.
18
Controls and features
Under normal conditions, your vehicle’s climate
control system should be left in any position other
than MAX A/C or OFF when the vehicle is parked.
This allows the vehicle to “breathe” through the
outside air inlet duct.
• MAX A/C-Uses recirculated air to cool the vehicle.
MAX A/C is noisier than NORM A/C but more
economical and will cool the inside of the vehicle
faster. Airflow will be from the instrument panel
registers. This mode can also be used to reduce
undesirable odors from entering the vehicle.
• NORM A/C-Uses outside air to cool the vehicle. It
is quieter than MAX A/C but not as economical.
Airflow will be from the instrument panel
registers.
• VENT-Distributes outside air through the
instrument panel registers. However, the air will
not be cooled below the outside temperature
because the air conditioning does not operate in
this mode.
• OFF-Outside air is shut out and the fan will not
operate. For short periods of time only, use this
mode to prevent undesirable odors from entering
the vehicle.
• FLR-Allows for maximum heating by distributing
outside air through the floor ducts. However, the
air will not be cooled below the outside
temperature because the air conditioning does not
operate in this mode.
• MIX-Distributes outside air through the
windshield defroster ducts and the floor ducts.
Heating and air conditioning capabilities are
provided in this mode. For added customer
comfort, when the temperature control knob is
anywhere in between the full hot and full cold
positions, the air distributed through the floor
ducts will be slightly warmer than the air sent to
the windshield defroster ducts. If the temperature
19
Controls and features
is about 10°C (50°F) or higher, the air conditioner
will automatically dehumidify the air to reduce
fogging.
•
- Distributes outside air through the
windshield defroster ducts. It can be used to clear
ice or fog from the windshield. If the temperature is
about 10°C (50°F) or higher, the air conditioner will
automatically dehumidify the air to reduce fogging.
Operating tips
• In humid weather, select
before driving. This
will prevent your windshield from fogging. After a
few minutes, select any desired position.
• To reduce humidity buildup inside the vehicle,
don’t drive with the climate control system in the
OFF position.
• Don’t put objects under the front seat that will
interfere with the airflow to the back seats.
• Remove any snow,
ice or leaves from
the air intake area
(at the bottom of
the windshield).
• If your vehicle has been parked with the windows
closed during hot weather, the air conditioner will do
a much faster job of cooling if you drive for two or
three minutes with the windows open. This will force
most of the hot, stale air out of the vehicle. Then
operate your air conditioner as you would normally.
• When placing objects on top of your instrument
panel, be careful to not place them over the
defroster outlets. These objects can block airflow
and reduce your ability to see through your
windshield. Also, avoid placing small objects on top
of your instrument panel. These objects can fall
down into the defroster outlets and block airflow
and possibly damage your climate control system.
20
Controls and features
USING YOUR AUDIO SYSTEM
AM/FM Stereo/Cassette/Premium Sound
FM 1
ST
DOLBY SYSTEM
POWER
AUDIO
AM/FM
1
2
3
–
VOLUME
+
4
5
CLOCK
Power control
Press the control to
turn the audio system
on or off.
SCAN
AMS
SEEK
POWER
Volume control
Press the control to
–
+
VOLUME
raise or lower volume.
If the volume is set
above a certain level and the ignition is turned off,
the volume will come back on at a “nominal”
listening level when the ignition switch is turned
back on. If you wish to maintain your preset volume
level, turn the audio system off with the power
control before switching off the ignition.
AM/FM select
The AM/FM select
AM/FM
control works in radio
mode and allows you
to select AM or FM
frequency bands.
Press the control to switch between AM, FM1 or
FM2 memory preset stations.
Tune adjust in radio mode
Tune adjust allows you
to tune in a particular
radio station. You can
manually locate the
AMS
21
Controls and features
station by using the Automatic Music Search (AMS)
button.
• Press the AMS control until the display shows
TUNE.
• Press and release
SEEK
either
or
on
the SEEK control to
change to the next frequency up or down.
• Press and hold down
or
to quickly move
through the frequencies.
Seek function
The seek function control works in radio or tape mode.
Seek function in radio mode
• Press
to find the
SEEK
next listenable
station down the
frequency band.
• Press
to find the next listenable station up the
frequency band.
Seek function in tape mode
The Automatic Music
Search (AMS) feature
AMS
allows you to quickly
locate the beginning of
the tape selection being played or to skip to the
next selection.
• Press the AMS control.
• Press
to listen
to the previous
selection on the
tape.
to listen to the next selection on the
• Press
tape.
The tape deck stops and returns to play mode when
the AMS circuit senses a blank section on the tape.
22
Controls and features
In order to ensure proper operation of the AMS
feature, the tape MUST have a blank section of at
least 4 seconds duration between programs.
Scan function
The scan function
works in radio mode.
SCAN
• Press the SCAN button to activate the scan mode.
The radio scans up the frequency band, stopping
on each listenable station for approximately a
five-second sampling.
• Press the SCAN button a second time to
deactivate the feature.
Radio station memory preset
The radio is equipped with five station memory
preset controls. These controls can be used to select
up to five preset AM stations and ten FM stations
(five in FM1 and five in FM2).
Setting memory preset stations
1. Select the frequency
AM/FM
band with the AM/FM
select control.
2. Select a station. Refer to Tune adjust or Seek
function for more information on selecting a station.
3. Press and hold a
1
2
3
memory preset control
4
5
until the sound returns,
indicating the station is
held in memory on the control you selected.
Repeat the steps for each station memory preset
button you want to set.
If the battery is disconnected, the memory preset
stations will need to be reset.
23
Controls and features
Bass adjust
The bass adjust control allows you to increase or
decrease the audio system’s bass output.
• Push the AUDIO
control repeatedly
AUDIO
until the display
reads BASS.
• Press (+) or (−) on
–
+
VOLUME
the volume control
to increase or
decrease bass output.
Treble adjust
The treble adjust control allows you to increase or
decrease the audio system’s treble output.
• Push the AUDIO
control repeatedly
AUDIO
until the display
reads TREB.
• Press (+) or (−) on
–
+
VOLUME
the volume control
to increase or
decrease treble output.
Speaker balance adjust
Speaker sound distribution can be adjusted between
the right and left speakers.
• Push the AUDIO
control repeatedly
AUDIO
until the display
reads BAL.
• Press the (+) side of
–
+
VOLUME
the volume control
to shift sound to the
right speakers.
• Press the (−) side of the volume control to shift
sound to the left speakers.
24
Controls and features
Speaker fade adjust
Speaker sound distribution can be adjusted between
the front and rear speakers.
• Push the AUDIO
control repeatedly
AUDIO
until the display
reads FADE.
• Press the (+) side of
–
+
VOLUME
the volume control
to shift sound to the
front speakers.
• Press the (−) side of the volume control to shift
sound to the rear speakers.
Tape play select
Insert a tape to begin tape play.
Push only slightly when inserting a cassette tape
(with the open edge to the right). A cassette deck
loading mechanism pulls the tape in the rest of the
way.
Rewind/fast forward
The rewind and fast forward controls work in tape
mode.
Rewind/fast forward function in tape mode
• Press
to
rewind the tape.
Play will continue
once the beginning
of the tape is reached or rewind is stopped.
to fast forward the tape. Once the end
• Press
of the tape is reached, tape direction reverses and
the opposite side of the tape plays.
25
Controls and features
Tape eject
Press the control to
stop and eject a tape.
Dolby T noise reduction
Dolbyt noise reduction
manufactured under
license from Dolby
Laboratories Licensing
Corporation operates only in tape mode. Dolbyt
reduces the amount of hiss and static during tape
playback.
Press the
button to activate (and deactivate)
Dolbyt noise reduction.
Setting the clock
Press the CLOCK
control while
simultaneously
depressing the SEEK control.
• Press
to set the
hours.
to set the
• Press
minutes.
26
CLOCK
SEEK
Controls and features
AM/FM Stereo/Cassette/MACH 460 Sound
SystemT with Premium AM/FM Stereo Cassette
FM1
REW
AUTOMATIC
DNR CrO2
ST
FF
PLAY EJCT
PROG
POWER
AUDIO
VOLUME
AM/FM
1
2
3
4
5
CLOCK
Power control
Press the control to
turn the audio system
on or off.
AUTO
PRESET
SCAN
TUNE
SEEK
POWER
Volume control
Press the control to
VOLUME
raise or lower volume.
If the volume is set
above a certain level and the ignition is turned off,
the volume will come back on at a “nominal”
listening level when the ignition switch is turned
back on. If you wish to maintain your preset volume
level, turn the audio system off with the power
control before switching off the ignition.
AM/FM select
The AM/FM select
AM/FM
control works in radio
mode and allows you to
select AM or FM
frequency bands.
Press the control to switch between AM, FM1 or
FM2 memory preset stations.
27
Controls and features
Tune adjust
Tune adjust works in
SCAN
radio mode and allows
TUNE
you to manually tune in
a particular radio
station.
• Press the SCAN/TUNE button twice.
• The display reads TUNE.
Press the SEEK control
SEEK
to move up or down
through the
frequencies.
to move down or
to move up the
• Press
frequency band.
• Press and hold down
or
to quickly move
through the frequencies.
Seek function
The seek function control works in radio or tape
mode.
Seek function in radio mode
This feature allows you
SEEK
to automatically select
listenable stations up
or down the frequency band.
• Press
to find the next listenable station down
the frequency band.
• Press
to find the next listenable station up the
frequency band.
Seek function in tape mode
This feature allows you
SEEK
to locate the beginning
of the tape selection
being played or to skip to the next selection.
• Press
to listen to the previous selection on the
tape.
28
Controls and features
• Press
tape.
to listen to the next selection on the
Scan function
The scan function works in radio, tape and CD mode
(if equipped).
Scan function in radio mode
This feature allows you
SCAN
to scan the frequency
TUNE
band, stopping on each
listenable station for
approximately a five-second sampling.
• Press the SCAN/TUNE button to enter the scan
mode.
• This display reads SCN.
Use the SEEK button
SEEK
to scan up or down the
frequency band.
to find the next listenable station down
• Press
the frequency band.
• Press
to find the next listenable station up the
frequency band.
Scan function in tape mode
This feature allows you
SCAN
to scan the tape
TUNE
currently playing,
stopping on each
selection for approximately an eight-second
sampling.
• Press the SCAN/TUNE button to enter the scan
mode.
• The display reads SCN.
Use the SEEK button
SEEK
to scan the desired
direction on the tape.
to scan previous selections.
• Press
29
Controls and features
• Press
to scan forward selections.
Press the SCAN/TUNE button again to stop the scan
mode on the current selection.
Radio station memory preset
The radio is equipped with five station memory
preset controls. These controls can be used to select
up to five preset AM stations and ten FM stations
(five in FM1 and five in FM2).
Setting memory preset stations
1. Select the frequency
AM/FM
band with the AM/FM
select control.
2. Select a station. Refer to Seek function for more
information on selecting a station.
3. Press and hold a
1
2
3
memory preset control
until the sound returns,
4
5
indicating the station is
held in memory on the control you selected.
If the battery is disconnected, the memory preset
stations will need to be reset.
Bass adjust
The bass adjust control allows you to increase or
decrease the audio system’s bass output.
• Push the AUDIO
AUDIO
control repeatedly
until the display
reads BASS.
• Press (+) or (−) on
VOLUME
the volume control
to increase or
decrease bass output.
Treble adjust
The treble adjust control allows you to increase or
decrease the audio system’s treble output.
30
Controls and features
• Push the AUDIO
control repeatedly
until the display
reads TREB.
• Press (+) or (−) on
the volume control
to increase or
decrease treble output.
AUDIO
VOLUME
Speaker balance adjust
Speaker sound distribution can be adjusted between
the right and left speakers.
• Push the AUDIO
AUDIO
control repeatedly
until the display
reads BAL.
• Press the (+) side of
VOLUME
the volume control
to shift sound to the
right speakers.
• Press the (−) side of the volume control to shift
sound to the left speakers.
Speaker fade adjust
Speaker sound distribution can be adjusted between
the front and rear speakers.
• Push the AUDIO
AUDIO
control repeatedly
until the display
reads FADE.
• Press the (+) side of
VOLUME
the volume control
to shift sound to the
front speakers.
• Press the (−) side of the volume control to shift
sound to the rear speakers.
Tape play select
Insert a cassette tape into the cassette deck.
31
Controls and features
Push only slightly when inserting a cassette tape
(with the open edge to the right). A cassette deck
loading mechanism pulls the tape in the rest of the
way.
Press PLAY to begin
PLAY
cassette tape play.
PROG
Rewind/fast forward function in tape mode
Press the control to
rewind the tape.
REW
Play will continue once
the beginning of the
tape is reached or rewind is stopped.
Press the control to
fast forward the tape.
FF
Once the end of the
tape is reached, tape
direction reverses and the opposite side of the tape
plays.
Tape eject
Press the control to
stop and eject a tape.
EJCT
Dolby T noise reduction
Dolbyt noise reduction
manufactured under
license from Dolby
Laboratories Licensing
Corporation operates only in tape mode. Dolbyt
reduces the amount of hiss and static during tape
playback.
button to activate (and deactivate)
Press the
Dolbyt noise reduction.
32
Controls and features
Setting the clock
Press the CLOCK
control while
simultaneously
depressing the SEEK
control.
• Press
to set the
hours.
• Press
to set the
minutes.
CLOCK
SEEK
Premium AM/FM Stereo Single CD
Radio/Premium Sound or MACH 460 Sound
SystemT with Single CD Radio
POWER
DISC
EJECT
COMP
AM/FM
REV
FF
AUDIO
AUTO
PLAY
SCAN
+
VOL
–
AUTOMATIC DNR
PRESET
1
2
Power control
Press the control to
turn the audio system
on or off.
3
4
STOP
5
TUNE
SEEK
CLOCK
POWER
Volume control
Press the control to
+
raise or lower volume.
VOL
If the volume is set
above a certain level
–
and the ignition is
turned off, the volume
will come back on at a “nominal” listening level
when the ignition switch is turned back on. If you
wish to maintain your preset volume level, turn the
audio system off with the power control before
switching off the ignition.
33
Controls and features
AM/FM select
The AM/FM select
AM/FM
control works in radio
mode and allows you
to select AM or FM
frequency bands.
Press the control to switch between AM, FM1 or
FM2 memory preset stations.
Tune adjust
The tune control works in radio mode.
Tune adjust in radio mode
• Press the SCAN/
TUNE control twice.
• Within approximately
five seconds, press
and release either
or
on the
SEEK button to
change to the next
frequency up or
down.
• Press and hold down
or
through the frequencies.
SCAN
TUNE
SEEK
to quickly move
Seek function
The seek function control works in radio mode.
Seek function in radio mode
• Press
to find the
next listenable
station down the
frequency band.
to find the
• Press
next listenable
station up the frequency band.
34
SEEK
Controls and features
Scan function
The scan function
works in radio mode.
SCAN
TUNE
Scan function with compact disc radio
• Press the SCAN/
SCAN
TUNE control once.
TUNE
on the
• Push
SEEK control to
hear a brief sampling
of listenable stations
SEEK
up the frequency
band.
to hear a
• Push
brief sampling of
listenable stations down the frequency band.
Setting memory preset stations
1. Select the frequency
AM/FM
band with the AM/FM
select control.
2. Select a station. Refer to Tune adjust or Seek
function for more information on selecting a station.
1
2
3
4
5
CLOCK
3. Press and hold a memory preset control until the
sound returns, indicating the station is held in
memory on the control you selected.
If the battery is disconnected, the memory preset
stations will need to be reset.
Automatic memory store (if equipped)
Automatic memory store allows you to set strong
radio stations without losing your original manually
35
Controls and features
set preset stations. This feature is helpful on trips
when you travel between cities with different radio
stations.
Starting automatic memory store
1. Select a frequency
AM/FM
using the AM/FM select
control.
2. Press the AUTO
PRESET control.
AUTO
PRESET
3. When the first six strong stations are filled, the
station stored in memory preset control 1 will start
playing.
If there are less than six strong stations available on
the frequency band, the remaining memory preset
controls will all store the last strong station
available.
Deactivating automatic memory store
To deactivate automatic memory store and return to
your audio system’s manually set memory stations,
press the AUTO PRESET control again.
Speaker balance adjust
Speaker sound distribution can be adjusted between
the right and left speakers.
• Push the AUDIO
control repeatedly
AUDIO
until the display
reads BAL.
• Press the (+) side of
+
the volume control
to shift sound to the
VOL
right speakers.
–
• Press the (−) side of
the volume control
to shift sound to the left speakers.
36
Controls and features
Speaker fade adjust
Speaker sound distribution can be adjusted between
the front and rear speakers.
• Push the AUDIO
control repeatedly
AUDIO
until the display
reads FADE.
• Press the (+) side of
+
the volume control
to shift sound to the
VOL
front speakers.
–
• Press the (−) side of
the volume control
to shift sound to the rear speakers.
Reverse/fast forward in CD mode
• Press the control for
REV
less than three
seconds for slow
reverse.
• Press the control for more than three seconds for
fast reverse.
• Press the control for
FF
less than three
seconds for slow
forward action.
• Press the control for more than three seconds for
fast forward action.
CD eject
Press the control to
EJECT
stop and eject a CD.
If a disc is ejected from
the CD player but is
not removed within approximately 10 seconds, the
player will automatically reload the disc for storage
(unless the disc is automatically ejected because it
was inserted upside down, in which case the disc
will not be automatically reloaded).
37
Controls and features
Compression feature
Compression adjust brings soft and loud CD
passages together for a more consistent listening
level.
Press the COMP control to activate and deactivate
compression adjust.
The effect of the feature varies with the music
content.
Setting the clock
Press the CLOCK
control while
simultaneously
depressing the SEEK control.
to set the
• Press
hours.
• Press
to set the
minutes.
CLOCK
SEEK
Single Disc CD Player (if equipped)
EJECT
DISC
COMPRESS
SHUFFLE
AMS
SCAN
PLAY/STOP
REV/FF
Power and volume control
The compact disc player operates when the audio
system is on and a CD is inserted (label side up).
The volume is controlled by the VOLUME control on
the audio system.
38
Controls and features
Play function
The system enters the
PLAY/STOP
PLAY mode when a CD
is loaded, label side up,
into the disc opening.
The PLAY indicator will illuminate. The CD
automatically loads into the unit and begins play at
the beginning of the first track. When the CD
reaches the end, the disc player automatically
returns to the beginning of the CD and resumes
play.
Stop function
Press the PLAY/STOP
PLAY/STOP
control to temporarily
stop CD play. The stop
indicator illuminates
and operation returns to the radio or tape mode.
Press the control again to resume CD play.
Scan function
Press the SCAN control
SCAN
to enter the scan
mode. The CD player
will begin scanning the
CD, stopping on each listenable track for
approximately eight seconds. This continues until
you press the SCAN control a second time or eject
the CD. While in the scan mode, the display flashes
SCAN.
Reverse/fast forward
To quickly
REV/FF
search for
a particular
point in a selection, press the right side of the
REV/FF control (to fast forward) or the left side (to
reverse). If you hold down the desired function for
longer than a few seconds, the process will speed
up. Release the button when you have reached the
desired point of the CD.
39
Controls and features
If you hold down the fast forward control until the
end of the CD is reached, the display will show the
end time of the last track and the sound will be
muted. When the fast forward control is released,
the player will resume play at the beginning of the
first track.
AMS control
The AMS (Automatic
AMS
Music Search) control
on your CD player
allows you to quickly find a particular selection on
the disc. Press the left side of the AMS control to
locate a previous selection, or the right side to
locate a later selection.
Compression feature
Press the COMPRESS
COMPRESS
control to activate (and
deactivate) compression
adjust. Compression
adjust brings soft and loud CD passages together for
a more consistent listening level.
Shuffle feature
The shuffle feature
SHUFFLE
plays all tracks on the
current CD in random
order.
Press the SHUFFLE control to start this feature.
Random order play will continue until the control is
pressed again.
Eject
Push the EJECT
control to stop CD play,
eject the CD, and
resume radio or tape
operation.
40
EJECT
Controls and features
Troubleshooting the CD player (if equipped)
The laser beam used in the compact disc
player is harmful to the eyes. Do not
attempt to disassemble the case.
If sound skips:
• You may be traveling on a rough road, playing
badly scratched discs or the disc may be dirty.
Skipping will not scratch the discs or damage the
player.
If your changer does not work, it may be that:
• A disc is already loaded where you want to insert
a disc.
• The disc is inserted with the label surface
downward.
• The disc is dusty or defective.
• The player’s internal temperature is above 60°C
(140°F). Allow the player to cool down before
operating.
• A disc with format and dimensions not within
industry standards is inserted.
Cleaning compact discs
Inspect all discs for contamination before playing. If
necessary, clean discs only with an approved CD
cleaner and wipe from the center out to the edge.
Do not use circular motion.
CD and CD player care
• Handle discs by their edges only. Never touch the
playing surface.
• Do not expose discs to direct sunlight or heat
sources for extended periods of time.
• Do not insert more than one disc into the slot of
the CD player.
41
Controls and features
Cleaning cassette player (if equipped)
Clean the tape player head with a cassette cleaning
cartridge after ten to twelve hours of play in order
to maintain the best sound and operation.
Cassette and cassette player care
• Use only cassettes that are 90 minutes long or
less.
• Do not expose tapes to direct sunlight, high
humidity, extreme heat or extreme cold. Allow
tapes that may have been exposed to extreme
temperatures to reach a moderate temperature
before playing.
• Tighten very loose tapes by inserting a finger or
pencil into the hole and turning the hub.
• Remove loose labels before inserting tapes.
• Do not leave tapes in the cassette player for a
long time when not being played.
Radio frequency information
The Federal Communications Commission (FCC)
and the Canadian Radio and Telecommunications
Communications (CRTC) establish the frequencies
AM and FM stations may use for their broadcasts.
Allowable frequencies are:
AM 530, 540–1600, 1610 kHz
FM 87.9, 88.1–107.1, 107.9 MHz
Not all frequencies are used in a given area.
Radio reception factors
Three factors can affect radio reception:
• Distance/strength. The further an FM signal
travels, the weaker it is. The listenable range of
the average FM station is approximately 40 km
(24 miles). This range can be affected by “signal
modulation.” Signal modulation is a process radio
stations use to increase their strength/volume
relative to other stations.
42
Controls and features
• Terrain. Hills, mountains and tall buildings
between your vehicle’s antenna and the radio
station signal can cause FM reception problems.
Static can be caused on AM stations by power
lines, electric fences, traffic lights and
thunderstorms. Moving away from an interfering
structure (out of its “shadow”) returns your
reception to normal.
• Station overload. Weak signals are sometimes
captured by stronger signals when you pass a
broadcast tower. A stronger signal may
temporarily overtake a weaker signal and play
while the weak station frequency is displayed.
The audio system automatically switches to single
channel reception if it will improve the reception of
a station normally received in stereo.
Audio system warranties and service
Refer to the “Warranty Guide” for audio system
warranty information.
If service is necessary, see your dealer or a qualified
technician.
TURN SIGNAL CONTROL
• Push down to
activate the left turn
signal.
• Push up to activate
the right turn signal.
HI
LO
OFF
WINDSHIELD WIPER/WASHER CONTROLS
Rotate the windshield
wiper control to the
desired interval, low or
high speed position.
HI
LO
OFF
43
Controls and features
The bars of varying length are for intermittent
wipers. When in this position rotate the control
upward for fast intervals and downward for slow
intervals.
Push the control on
the end of the stalk to
activate washer. Push
and hold for a longer
wash cycle. The washer will automatically shut off
after ten seconds of continuous use.
HI
LO
OFF
Mist Function
To operate the Mist
function of the
windshield wipers,
push and release the
windshield washer control quickly. The wipers will
cycle one or two times.
HI
LO
OFF
HIGH BEAMS
Push forward to
activate.
HI
LO
OFF
FLASH TO PASS
Pull toward you to
activate and release to
deactivate.
44
HI
LO
OFF
Controls and features
POSITIONS OF THE IGNITION
1. ACCESSORY, allows
3
2
the electrical
accessories such as the
radio to operate while
the engine is not
1
running.
2. LOCK, locks the
steering wheel,
automatic transmission gearshift lever and allows
key removal.
3. OFF, shuts off the engine and all accessories
without locking the steering wheel.
4. ON, all electrical circuits operational. Warning
lights illuminated. Key position when driving.
5. START, cranks the engine. Release the key as
soon as the engine starts.
4
5
TILT STEERING WHEEL (IF EQUIPPED)
Pull the tilt steering
control toward you to
move the steering
wheel up or down.
Hold the control while
adjusting the wheel to
the desired position,
then release the
control to lock the
steering wheel in
position.
Never adjust the steering wheel when the
vehicle is moving.
45
Controls and features
SPEED CONTROL
To turn speed control on
• Press ON.
Vehicle speed cannot
be controlled until the
vehicle is traveling at
or above 48 km/h
(30 mph).
ON
OFF
Do not use the speed control in heavy traffic
or on roads that are winding, slippery, or
unpaved.
Do not shift the gearshift lever into N
(Neutral) with the speed control on.
To turn speed control off
• Press OFF or
• Turn off the vehicle
ignition.
ON
OFF
Once speed control is switched off, the previously
programmed set speed will be erased.
To set a speed
• Press SET/SET ACC/
SET ACCEL. For
speed control to
operate, the speed
control must be ON
and the vehicle
speed must be
greater than 48 km/h
(30 mph).
46
RSM
SET
ACC
COAST
Controls and features
If you drive up or down a steep hill, your vehicle
speed may vary momentarily slower or faster than
the set speed. This is normal.
Speed control cannot reduce the vehicle speed if it
increases above the set speed on a downhill. If your
vehicle speed is faster than the set speed while
driving on a downhill, you may want to shift to the
next lower gear or apply the brakes to reduce your
vehicle speed.
If your vehicle slows down more than 16 km/h
(10 mph) below your set speed on an uphill, your
speed control will disengage. This is normal.
Pressing RES/RSM/RESUME will re-engage it.
Do not use the speed control in heavy traffic
or on roads that are winding, slippery, or
unpaved.
To set a higher set speed
• Press and hold SET/
SET ACC/SET
RSM
ACCEL. Release the
SET
control when the
ACC
desired vehicle
COAST
speed is reached or
• Press and release
SET/SET ACC/SET
ACCEL. Each press will increase the set speed by
1.6 km/h (1 mph) or
• Accelerate with your accelerator pedal. When the
desired vehicle speed is reached, press and
release SET/SET ACC/SET ACCEL.
You can accelerate with the accelerator pedal at any
time during speed control usage. Releasing the
accelerator pedal will return your vehicle to the
previously programmed set speed.
47
Controls and features
To set a lower set speed
• Press and hold CST/
COAST. Release the
RSM
control when the
SET
desired speed is
ACC
reached or
COAST
• Press and release
CST/COAST. Each
press will decrease
the set speed by 1.6 km/h (1 mph) or
• Depress the brake
pedal. When the
RSM
desired vehicle
SET
speed is reached,
ACC
press SET/SET ACC/
COAST
SET ACCEL.
To disengage speed control
• Depress the brake
pedal or
• Depress the clutch
pedal (if equipped)
Disengaging the speed
control will not erase
the previously
programmed set speed.
48
Controls and features
Pressing OFF will erase
the previously
programmed set speed.
ON
OFF
To return to a previously set speed
• Press RES/RSM/
RESUME. For RES/
RSM
RSM/RESUME to
SET
operate, the vehicle
ACC
speed must be faster
COAST
than 48 km/h
(30 mph).
INTERIOR LAMPS
Map lamps (if equipped)
If equipped with a
convertible top the
map lamps and
controls are located on
the rearview mirror.
Press the controls on
either side of each map
lamp to activate the lamps.
READING LAMP
S
49
Controls and features
POWER WINDOWS (IF EQUIPPED)
Press and hold the rocker switches to open and
close windows.
• Press the top portion
of the rocker switch
to close.
• Press the bottom
portion of the rocker
switch to open.
Express down
To make the driver
window open fully
without holding the
window control, press
the driver window
control completely down
and release quickly.
Depress again to stop
window operation.
Window lock
The window lock
feature allows only the
driver to operate the
power windows.
LOCK
To lock out all the
window controls except
for the driver’s press the control. Press the control
again to restore the window controls.
50
Controls and features
POWER DOOR LOCKS
Press U to unlock all
doors and L to lock all
doors.
U
L
POWER SIDE VIEW MIRRORS (IF EQUIPPED)
To adjust your mirrors:
1. Select
to adjust the left mirror or
to adjust
the right mirror.
2. Move the control in
the direction you wish
to tilt the mirror.
3. Return to the center position to lock mirrors in
place.
POSITIVE RETENTION FLOOR MAT
(IF EQUIPPED)
Position the floor mat so
that the eyelet is over the
pointed end of the
retention post and rotate
forward to lock in. Make
sure that the mat does not
interfere with the operation
of the accelerator or the
brake pedal. To remove the
floor mat, reverse the installation procedure.
51
Controls and features
CENTER CONSOLE
Your vehicle may be equipped with a variety of
console features. These include:
• dual cupholders
• auxiliary power point
• coin holder slots (if equipped)
• foglamp control (if equipped)
• convertible top control (if equipped)
Use only soft cups in the cupholder. Hard
objects can injure you in a collision.
Foglamp control (if equipped)
Turn on the parking
lamps or the low-beam
headlamps. Press the
top portion of the
foglamp control,
located on the center
console, to activate the
foglamps. The foglamp
LED will illuminate when the foglamps are on.
Press the bottom portion of the foglamp control to
deactivate the foglamps.
Auxiliary power point
The power point is an
additional power
source for electrical
accessories.
52
Controls and features
Convertible (If equipped)
Do not store articles behind rear seat. Articles
stored in the convertible top stowage compartment
may break the rear glass window when the top is
lowered.
Lowering the convertible top
The convertible top can be lowered with the side
windows either up or down.
The convertible top will not operate unless the
parking brake is engaged. Do not lower the top while
the vehicle is moving because the top may be
severely damaged. Also, do not lower the top when
the top material is wet.
To lower the convertible top:
1. Bring vehicle to a complete stop. Engage the
parking brake. Key must be in the ON position.
2. Check the convertible top stowage compartment
behind the rear seat to be sure it is empty and ready
to receive the top.
3. Unclamp the top from the windshield header at
both the right and left sides by pulling each clamp
rearward until the hook in the windshield header is
free. The clamps are flush with the header when in
the closed position.
4. Close the windshield header clamps immediately
after disengagement, to avoid cutting the top
material and to permit installation of the vinyl boot.
5. If the top has not
been lowered for some
time and sticks to the
windshield header,
push the front of the
top up slightly with
your hand to loosen it.
53
Installation of the boot
1. Insert boot tongue
into groove located on
rear seat.
2. Push boot forward
until rear attachment
engages under
molding.
3. Push forward flap of
boot until both clips
engage under trim
panel edge. Repeat on
other side of vehicle.
54
T
PARK BRAK
E
6. Push the convertible
top switch on the
console in front of the
armrest and hold until
the top is completely
stored.
7. Disengage the
parking brake.
SE
Controls and features
Controls and features
4. Tuck side
attachments under
molding. Repeat on
other side of vehicle.
5. Push and pull front
of boot to ensure
tongue is engaged into
groove.
6. Removal
Raising the convertible top
The convertible top will not operate unless the
parking brake is engaged. Do not raise the top while
the vehicle is moving because the top may be
severely damaged.
To raise the convertible top:
1. Bring the vehicle to a complete stop. Engage the
parking brake. Key must be in the ON position.
2. Remove the boot cover and store it in the luggage
compartment.
3. Lower the front and rear side windows.
4. Push the convertible top button, holding it until
the top unfolds and moves forward toward the
windshield header.
55
Controls and features
5. Open both top clamps before the top meets the
windshield header
6. Continue to use the top motor to raise the top
until it has reached the fully closed position flush to
the header.
7. The two pins under the forward edge of the top
should seat themselves in the matching holes in the
header.
8. To fasten both clamps securely, push the clamp
handles into the header on the top until they are
flush with the header. Pulling down on the header at
the center grip while closing the latches may assist
in fastening the clamps.
9. Raise the front and rear side windows.
10. Disengage the parking brake.
REMOTE ENTRY SYSTEM
The remote entry system allows you to:
• lock or unlock all vehicle doors without a key.
• open the trunk.
• activate the panic alarm.
• confirms that the vehicle is locked with a short
“beep” from the horn.
The remote entry features only operate with the
ignition in the OFF position.
Unlocking the doors
Press this control to
unlock the driver’s
door. The interior
lamps will illuminate.
With the all-door
remote entry system,
press the control a
second time within
three seconds to unlock the passenger door.
56
Controls and features
Locking the doors
Press this control to
lock all doors.
To confirm all doors
are closed and locked,
press the control a
second time within
three seconds. The
doors will lock again,
the horn will chirp and the lamps will flash.
If any of the doors are ajar, the horn will make two
quick chirps and the chime may sound, reminding
you to properly close all doors.
Opening the trunk
Press the control once
to open the trunk.
Ensure that the trunk
is closed and latched
before driving your
vehicle. Failure to latch
the trunk may cause
objects to fall out of
the trunk or block the rear view.
Sounding a panic alarm
Press this control to
activate the alarm.
To deactivate the alarm,
press the control again
or turn the ignition to
ACC or ON.
This device complies
with part 15 of the
FCC rules and with RS-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) This device must accept any interference
received, including interference that may cause
undesired operation.
57
Controls and features
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
Illuminated entry
The interior lamps illuminate when the remote entry
system is used to unlock the door(s) or sound the
personal alarm.
The system automatically turns off after 25 seconds
or when the ignition is turned to the START/RUN or
ACC position. The dome lamp control (if equipped)
must not be set to the OFF position for the
illuminated entry system to operate.
The inside lights will not turn off if:
• they have been turned on with the dimmer
control or
• any door is open.
The battery saver will shut off the interior lamps
30 minutes after the ignition has been turned to the
OFF position, 10 minutes after if the door is left
open, and 30 minutes after if the trunk is left open
or the dome lamp switch is left on.
Replacing lost transmitters
Take all your vehicle’s
transmitters to your
dealer if service is
required.
If you purchase
additional transmitters
(up to four may be
programmed), perform
the following procedure:
To reprogram the transmitters, place the key in the
ignition and turn from OFF to ON eight times in
rapid succession (within 10 seconds) ending in ON.
58
Controls and features
After doors lock/unlock, press any control on all
transmitters (up to four). With each control press of
the transmitters, the door should cycle (lock/unlock)
to confirm programming. When completed, turn the
ignition to OFF. The door locks should cycle
(lock/unlock) one last time to confirm completion of
programming.
All transmitters must be programmed at the same
time.
Replacing the batteries
The transmitter is powered by two coin type
three-volt lithium batteries. Typical operating range
will allow you to be up to 10 meters (33 feet) away
from your vehicle. A decrease in operating range can
be caused by:
• weather conditions
• nearby radio towers
• structures around the vehicle
• other vehicles parked next to the vehicle
To replace the
batteries:
1. Twist a thin coin
between the two halves
of the transmitter near
the key ring. DO NOT
TAKE THE FRONT
PART OF THE
TRANSMITTER
APART.
2. Place the positive
(+) side of new batteries down. Refer to the diagram
inside the transmitter unit.
3. Snap the two halves back together.
59
Controls and features
SECURILOCKY PASSIVE ANTI-THEFT SYSTEM
The SecuriLocky passive anti-theft system provides
an advanced level of vehicle theft protection. Your
vehicle’s engine can only be started with the two
special SecuriLocky electronically coded keys
provided with your vehicle. Each time you start your
vehicle, the SecuriLocky key is read by the
SecuriLocky passive anti-theft system. If the
SecuriLocky key identification code matches the
code stored in the SecuriLocky anti-theft system,
the vehicle’s engine is allowed to start. If the
SecuriLocky key identification code does not match
the code stored in the system or if a SecuriLocky
key is not detected (vehicle theft situation), the
vehicle’s engine will not operate.
The SecuriLocky passive anti-theft system is not
compatible with aftermarket remote start systems.
Use of these systems may result in vehicle starting
problems and a loss of security protection. Large
metallic objects or devices such as the Mobil
Speedpassy on the same key ring as your
SecuriLocky key may cause vehicle starting
problems. These objects and devices cannot damage
the SecuriLocky key, but can cause a momentary
problem if they are too close to the key when
starting the engine. If a problem occurs. turn
ignition off and restart the engine with all other
objects on the key ring held away from the
SecuriLocky ignition key.
Spare SecuriLocky keys can be purchased from
your dealership and programmed to your
SecuriLocky passive anti-theft system. Refer to
Programming spare SecuriLocky keys for more
information.
If one or both of your SecuriLocky keys are lost or
stolen and you want to ensure the lost or stolen key
will not operate your vehicle, bring your vehicle and
all available SecuriLocky keys to your dealership for
reinitialization.
60
Controls and features
Theft indicator
The theft indicator on the instrument cluster will
operate as follows:
• When the ignition is OFF, the theft indicator will
flash briefly every 2 seconds to indicate the
SecuriLocky system is protecting your vehicle.
• When the ignition is turned to RUN or START, the
theft indicator will light for 3 seconds and then go
out. If the theft indicator stays on for an extended
period of time or flashes rapidly, have the system
serviced by your dealership or a qualified technician.
Programming spare SecuriLockY keys
Spare SecuriLocky keys can be purchased from
your dealership and programmed to your
SecuriLocky passive anti-theft system (up to a total
of 8 keys). Your dealership can program your new
SecuriLocky key(s) to your vehicle or you can do it
yourself using the following simple procedure. To
program a new SecuriLocky key yourself, you will
need two previously programmed SecuriLocky keys
(keys that already operate your vehicle’s engine). If
two previously programmed SecuriLocky keys are
not available (one or both of your original keys were
lost or stolen), you must bring your vehicle to your
dealership to have the spare SecuriLocky key(s)
programmed.
Procedure to program spare SecuriLockY keys
to your vehicle
New SecuriLocky keys must have the correct
mechanical key cut for your vehicle.
Conventional (non-SecuriLocky) keys cannot be
programmed to your vehicle.
You will need to have two previously programmed
SecuriLocky keys and the new unprogrammed
SecuriLocky key readily accessible for the
procedure. Please read and understand the entire
procedure before you begin.
61
Controls and features
1. Insert the first previously programmed
SecuriLocky key into the ignition and turn the
ignition from OFF to RUN (maintain ignition in RUN
for at least one second).
2. Turn ignition to OFF and remove the first
SecuriLocky key from the ignition.
3. Within five seconds of turning the ignition to OFF,
insert the second previously programmed
SecuriLocky key into the ignition and turn the
ignition from OFF to RUN (maintain ignition in RUN
for at least one second but no more than 5 seconds).
4. Turn the ignition to OFF and remove the second
SecuriLocky key from the ignition.
5. Within 10 seconds of turning the ignition to OFF,
insert the unprogrammed SecuriLocky key (new
key) into the ignition and turn the ignition from OFF
to RUN (maintain ignition in RUN for at least one
second). This step will program your new
SecuriLocky key.
6. To program additional SecuriLocky key(s), repeat
this procedure from step 1.
If the programming procedure was successful, the
new SecuriLocky key(s) will start the vehicle’s
engine. The theft indicator (located on the
instrument cluster) will light for three seconds and
then go out.
If the programming procedure was not successful,
the new SecuriLocky key(s) will not operate the
vehicle’s engine. The theft indicator will flash on and
off. Wait at least one minute and then repeat the
procedure from step 1. If failure repeats, bring your
vehicle to your dealership to have the spare
SecuriLocky key(s) programmed.
62
Seating and safety restraints
SEATING
Adjustable head restraints (if equipped)
Your vehicle’s seats may be equipped with head
restraints which are vertically adjustable. The
purpose of these head restraints is to help limit head
motion in the event of a rear collision. To properly
adjust your head restraints, lift the head restraint so
that it is located directly behind your head or as
close to that position as possible. Refer to the
following to raise and lower the head restraints.
The head restraints can
be moved up and
down.
Adjusting the front manual seat
Never adjust the driver’s seat or seatback
when the vehicle is moving.
Do not pile cargo higher than the seatbacks
to avoid injuring people in a collision or
sudden stop.
Always drive and ride with your seatback
upright and the lap belt snug and low across
the hips.
63
Seating and safety restraints
Lift handle to move
seat forward or
backward.
Pull lever up to adjust
seatback.
Adjusting the front power seat (if equipped)
Never adjust the driver’s seat or seatback
when the vehicle is moving.
Do not pile cargo higher than the seatbacks
to avoid injuring people in a collision or
sudden stop.
Always drive and ride with your seatback
upright and the lap belt snug and low across
the hips.
64
Seating and safety restraints
Press to raise or lower
the front portion of the
seat cushion.
Press to raise or lower
the rear portion of the
seat cushion.
Press the control to
move the seat forward,
backward, up or down.
Rear seat entry/exit
Use the seatback release to fold the back of the
front seat forward for rear seat passenger entry or
exit. This release handle is located on the lower
outboard back of the seat. The seatback locks
automatically when returned to the normal position.
Using the power lumbar support (if equipped)
The power lumbar
control is located on
the outboard side of
the seat.
Press one side of the control to adjust firmness.
Press the other side of the control to adjust
softness.
65
Seating and safety restraints
Using the manual lumbar support (if equipped)
The lumbar control is
located on the inboard
side of the driver’s
seatback.
Move the control up to
increase firmness and
down to decrease
firmness.
2nd seat/Split-folding rear seat (if equipped)
One or both rear seatbacks can be folded down to
provide additional cargo space.
To lower the
seatback(s) from inside
the vehicle, pull tab to
release seat back and
then fold seatback
down.
When raising the seatback(s), make sure you hear
the seat latch into place.
SAFETY RESTRAINTS
Safety restraints precautions
Always drive and ride with your seatback
upright and the lap belt snug and low across
the hips.
66
Seating and safety restraints
To prevent the risk of injury, make sure
children sit where they can be properly
restrained.
Never let a passenger hold a child on his or
her lap while the vehicle is moving. The
passenger cannot protect the child from injury in a
collision.
All occupants of the vehicle, including the
driver, should always properly wear their
safety belts, even when an air bag SRS is provided.
It is extremely dangerous to ride in a cargo
area, inside or outside of a vehicle. In a
collision, people riding in these areas are more
likely to be seriously injured or killed. Do not allow
people to ride in any area of your vehicle that is
not equipped with seats and safety belts. Be sure
everyone in your vehicle is in a seat and using a
safety belt properly.
Each seating position in your vehicle has a
specific safety belt assembly which is made
up of one buckle and one tongue that are designed
to be used as a pair. 1) Use the shoulder belt on
the outside shoulder only. Never wear the shoulder
belt under the arm. 2) Never swing the safety belt
around your neck over the inside shoulder.
3) Never use a single belt for more than one
person.
67
Seating and safety restraints
Combination lap and shoulder belts
1. Insert the belt tongue
into the proper buckle
(the buckle closest to
the direction the tongue
is coming from) until
you hear a snap and feel
it latch. Make sure the
tongue is securely
fastened in the buckle.
2. To unfasten, push
the release button and
remove the tongue
from the buckle.
The front and rear outboard safety restraints in the
vehicle are combination lap and shoulder belts. The
front and rear seat passenger outboard safety belts
have two types of locking modes described below:
Vehicle sensitive mode
The vehicle sensitive mode is the normal retractor
mode, allowing free shoulder belt length adjustment
to your movements and locking in response to
vehicle movement. For example, if the driver brakes
suddenly or turns a corner sharply, or the vehicle
receives an impact of 8 km/h (5 mph) or more, the
combination safety belts will lock to help reduce
forward movement of the driver and passengers.
Automatic locking mode
In this mode, the shoulder belt is automatically
pre-locked. The belt will still retract to remove any
slack in the shoulder belt.
The automatic locking mode is not available on the
driver safety belt.
68
Seating and safety restraints
When to use the automatic locking mode
• When a tight lap/shoulder fit is desired.
• Anytime a child safety seat is installed in a
passenger front or outboard rear seating position
(if equipped). Refer to Safety Restraints for
Children or Safety Seats for Children later in
this chapter.
How to use the automatic locking mode
• Buckle the
combination lap and
shoulder belt.
• Grasp the shoulder
portion and pull
downward until the
entire belt is
extracted.
• Allow the belt to retract. As the belt retracts, you
will hear a clicking sound. This indicates the
safety belt is now in the automatic locking mode.
How to disengage the automatic locking mode
Disconnect the combination lap/shoulder belt and
allow it to retract completely to disengage the
automatic locking mode and activate the vehicle
sensitive (emergency) locking mode.
69
Seating and safety restraints
Safety belt extension assembly
If the safety belt assembly is too short, even when
fully extended, 20 cm (8 inches) can be added to
the safety belt assembly by adding a safety belt
extension assembly (part number 611C22). Safety
belt extension assemblies can be obtained from your
dealer at no cost.
Use only extensions manufactured by the same
supplier as the safety belt. Manufacturer
identification is located at the end of the webbing on
the label. Also, use the safety belt extension only if
the safety belt is too short for you when fully
extended. Do not use extensions to change the fit of
the shoulder belt across the torso.
Safety belt warning light and indicator chime
The seat belt warning light illuminates in the
instrument cluster and a chime sounds to remind
the occupants to fasten their safety belts.
Conditions of operation
If...
The driver’s safety belt
is not buckled before
the ignition switch is
turned to the ON
position...
The driver’s safety belt
is buckled while the
indicator light is
illuminated and the
warning chime is
sounding...
The driver’s safety belt
is buckled before the
ignition switch is turned
to the ON position...
70
Then...
The safety belt warning
light illuminates for one
to two minutes and the
warning chime sounds
for four to eight
seconds.
The safety belt warning
light and warning chime
turn off.
The safety belt warning
light will turn on for
three seconds and then
turn off. The indicator
chime will remain off.
Seating and safety restraints
Safety belt maintenance
Inspect the safety belt systems periodically to make
sure they work properly and are not damaged.
Inspect the safety belts to make sure there are no
nicks, wears or cuts, replacing if necessary. All
safety belt assemblies, including retractors, buckles,
front seat belt buckle assemblies (slide bar)(if
equipped), shoulder belt height adjusters (if
equipped), child safety seat tether bracket
assemblies (if equipped), and attaching hardware,
should be inspected after a collision. Ford
recommends that all safety belt assemblies used in
vehicles involved in a collision be replaced. However,
if the collision was minor and a qualified technician
finds that the belts do not show damage and
continue to operate properly, they do not need to be
replaced. Safety belt assemblies not in use during a
collision should also be inspected and replaced if
either damage or improper operation is noted.
Failure to inspect and if necessary replace
the safety belt assembly under the above
conditions could result in severe personal injuries
in the event of a collision.
Refer to Cleaning and maintaining the safety
belts in the Maintenance and care section.
AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM
(SRS)
71
Seating and safety restraints
Important supplemental restraint system (SRS)
precautions
The supplemental
restraint system is
designed to work with
the safety belt to help
protect the driver and
right front passenger
from certain upper
body injuries.
Air bags DO NOT
inflate slowly or gently
and the risk of injury
from a deploying air bag is greatest close to the trim
covering the air bag module.
All occupants of the vehicle including the
driver should always properly wear their
safety belts even when air bag SRS is provided.
Always transport children 12 years old and
under in the back seat and always use
appropriate child restraints.
NHTSA recommends a minimum distance of
at least 25 cm (ten [10] inches) between an
occupant’s chest and the air bag module.
Steps you can take to properly position yourself
away from the airbag:
• Move your seat to the rear as far as you can while
still reaching the pedals comfortably.
• Recline the seat slightly (one or two degrees)
from the upright position.
72
Seating and safety restraints
Do not put anything on or over the air bag
module. Placing objects on or over the air
bag inflation area may cause those objects to be
propelled by the air bag into your face and torso
causing serious injury.
Do not attempt to service, repair, or modify
the Air Bag Supplemental Restraint System
or its fuses. See your Ford or Lincoln-Mercury
dealer.
Children and air bags
For additional
important safety
information, read all
information on safety
restraints in this guide.
Children must always
be properly restrained.
Accident statistics
suggest that children
are safer when
properly restrained in
the rear seating
positions than in the front seating position. Failure
to follow these instructions may increase the risk of
injury in a collision.
Air bags can kill or injure a child in a child
seat. NEVER place a rear-facing child seat
in front of an active air bag. If you must use a
forward-facing child seat in the front seat, move
the seat all the way back.
73
Seating and safety restraints
How does the air bag supplemental restraint
system work?
The air bag SRS is
designed to activate
when the vehicle
sustains sufficient
longitudinal
deceleration sufficient
to cause the sensors to
close an electrical
circuit that initiates air
bag inflation.
The fact that the air bags did not inflate in a
collision does not mean that something is wrong
with the system. Rather, it means the forces were
not of the type sufficient to cause activation. Air
bags are designed to inflate in frontal and
near-frontal collisions, not rollover, side-impact, or
rear-impacts.
The air bags inflate and
deflate rapidly upon
activation. After air bag
deployment, it is
normal to notice a
smoke-like, powdery
residue or smell the
burnt propellant. This
may consist of
cornstarch, talcum
powder (to lubricate
the bag) or sodium
compounds (e.g., baking soda) that result from the
combustion process that inflates the air bag. Small
amounts of sodium hydroxide may be present which
may irritate the skin and eyes, but none of the
residue is toxic.
While the system is designed to help reduce serious
injuries, it may also cause minor burns, abrasions,
swelling or temporary hearing loss. Because air bags
must inflate rapidly and with considerable force,
74
Seating and safety restraints
there is the risk of death or serious injuries such as
fractures, facial and eye injuries or internal injuries,
particularly to occupants who are not properly
restrained or are otherwise out of position at the
time of air bag deployment. Thus, it is extremely
important that occupants be properly restrained as
far away from the air bag module as possible while
maintaining vehicle control.
Several air bag system components get hot
after inflation. Do not touch them after
inflation.
If the air bag is deployed, the air bag will
not function again and must be replaced
immediately. If the air bag is not replaced, the
unrepaired area will increase the risk of injury in a
collision.
The SRS consists of:
• driver and passenger air bag modules (which
include the inflators and air bags),
• one or more impact and safing sensors,
• a readiness light and tone
• and the electrical wiring which connects the
components.
The diagnostic module monitors its own internal
circuits and the supplemental air bag electrical
system warning (including the impact sensors), the
system wiring, the air bag system readiness light, the
air bag back up power and the air bag ignitors.
Determining if the system is operational
The SRS uses a readiness light in the instrument
cluster or a tone to indicate the condition of the
system. Refer to the Air bag readiness section in
the Instrumentation chapter. Routine maintenance
of the air bag is not required.
75
Seating and safety restraints
A difficulty with the system is indicated by one or
more of the following:
• The readiness light
AIR
will either flash or
BAG
stay lit.
• The readiness light
will not illuminate immediately after ignition is
turned on.
• A series of five beeps will be heard. The tone
pattern will repeat periodically until the problem
and light are repaired.
If any of these things happen, even intermittently,
have the SRS serviced at your dealership or by a
qualified technician immediately. Unless serviced,
the system may not function properly in the event of
a collision.
Disposal of air bags and air bag equipped
vehicles
For disposal of air bags or air bag equipped vehicles,
see your local dealership or qualified technician. Air
bags MUST BE disposed of by qualified personnel.
SAFETY RESTRAINTS FOR CHILDREN
See the following sections for directions on how to
properly use safety restraints for children. Also see
Air Bag Supplemental Restraint System (SRS) in
this chapter for special instructions about using air
bags.
Important child restraint precautions
You are required by law to use safety restraints for
children in the U.S. and Canada. If small children
ride in your vehicle (generally children who are four
years old or younger and who weigh 18 kg [40 lbs]
or less), you must put them in safety seats made
especially for children. Check your local and state or
provincial laws for specific requirements regarding
the safety of children in your vehicle.
76
Seating and safety restraints
Never let a passenger hold a child on his or
her lap while the vehicle is moving. The
passenger cannot protect the child from injury in a
collision.
Always follow the instructions and warnings that
come with any infant or child restraint you might
use.
When possible, place children in the rear seat of
your vehicle. Accident statistics suggest that
children are safer when properly restrained in the
rear seating positions than in the front seating
position.
Children and safety belts
If the child is the proper size, restrain the child in a
safety seat.
Children who are too large for child safety seats (as
specified by your child safety seat manufacturer)
should always wear safety belts.
Follow all the important safety restraint and air bag
precautions that apply to adult passengers in your
vehicle.
If the shoulder belt portion of a combination lap and
shoulder belt can be positioned so it does not cross
or rest in front of the child’s face or neck, the child
should wear the lap and shoulder belt. Moving the
child closer to the center of the vehicle may help
provide a good shoulder belt fit.
Do not leave children, unreliable adults, or
pets unattended in your vehicle.
To improve the fit of lap and shoulder belts on
children who have outgrown child safety seats, Ford
recommends use of a belt-positioning booster seat
that is labelled as conforming to all Federal motor
vehicle safety standards. Belt-positioning booster
77
Seating and safety restraints
seats raise the child and provide a shorter, firmer
seating cushion that encourages safer seating
posture and better fit of lap and shoulder belts on
the child.
A belt-positioning booster should be used if the
shoulder belt rests in front of the child’s face or
neck, or if the lap belt does not fit snugly on both
thighs, or if the thighs are too short to let the child
sit all the way back on the seat cushion when the
lower legs hang over the edge of the seat cushion.
You may wish to discuss the special needs of your
child with your pediatrician.
SAFETY SEATS FOR CHILDREN
Child and infant or child safety seats
Use a safety seat that is recommended for the size
and weight of the child. Carefully follow all of the
manufacturer’s instructions with the safety seat you
put in your vehicle. If you do not install and use the
safety seat properly, the child may be injured in a
sudden stop or collision.
78
Seating and safety restraints
When installing a child safety seat:
• Review and follow
the information
presented in the Air
Bag Supplemental
Restraint System
section in this
chapter.
• Use the correct
safety belt buckle for that seating position.
• Insert the belt tongue into the proper buckle until
you hear a snap and feel it latch. Make sure the
tongue is securely fastened in the buckle.
• Keep the buckle release button pointing up and
away from the safety seat, with the tongue
between the child seat and the release button, to
prevent accidental unbuckling.
• Place seat back in upright position.
• Put the safety belt in the automatic locking mode.
Refer to Automatic locking mode (passenger
side front and outboard rear seating positions)(if
equipped).
Ford recommends the use of a child safety seat
having a top tether strap. Install the child safety seat
in a seating position which is capable of providing a
tether anchorage. For more information on top
tether straps, refer to Attaching safety seats with
tether straps.
Carefully follow all of the manufacturer’s
instructions included with the safety seat
you put in your vehicle. If you do not install and
use the safety seat properly, the child may be
injured in a sudden stop or collision.
79
Seating and safety restraints
Installing child safety seats in combination lap
and shoulder belt seating positions
1. Position the child
safety seat in a seat
with a combination lap
and shoulder belt.
An air bag can kill or injure a child in a child
seat. If you must use a forward-facing child
seat in the front seat, move seat all the way back.
Children 12 and under should be properly
restrained in the rear seat whenever
possible.
2. Pull down on the
shoulder belt and then
grasp the shoulder belt
and lap belt together.
3. While holding the
shoulder and lap belt
portions together, route
the tongue through the
child seat according to
the child seat
manufacturer’s
instructions. Be sure
the belt webbing is not
twisted.
80
Seating and safety restraints
4. Insert the belt
tongue into the proper
buckle (the buckle
closest to the direction
the tongue is coming
from) for that seating
position until you hear
a snap and feel the
latch engage. Make
sure the tongue is
latched securely by
pulling on it.
5. To put the retractor
in the automatic
locking mode, grasp
the shoulder portion of
the belt and pull
downward until all of
the belt is extracted
and a click is heard.
6. Allow the belt to retract. The belt will click as it
retracts to indicate it is in the automatic locking mode.
7. Pull the lap belt
portion across the child
seat toward the buckle
and pull up on the
shoulder belt while
pushing down with
your knee on the child
seat.
8. Allow the safety belt
to retract to remove
any slack in the belt.
9. Before placing the
child in the seat,
forcibly tilt the seat
forward and back to
make sure the seat is
securely held in place.
81
Seating and safety restraints
10. Try to pull the belt out of the retractor to make
sure the retractor is in the automatic locking mode
(you should not be able to pull more belt out). If the
retractor is not locked, unbuckle the belt and repeat
steps two through nine.
Check to make sure the child seat is properly
secured before each use.
Attaching safety seats with tether straps
Some manufacturers make safety seats that include
a tether strap that goes over the back of the vehicle
seat and attaches to an anchoring point. Other
manufacturers offer the tether strap as an accessory.
Contact the manufacturer of your child safety seat
for information about ordering a tether strap.
Tether anchorage hardware
Attachment holes (at each rear seating position)
have been provided in your vehicle to attach anchor
hardware, if required. Tether anchorage hardware
kits (part number 613D74) including instructions,
may be obtained at no charge from any Ford or
Lincoln-Mercury dealer. All vehicles built for sale in
Canada include a tether anchor hardware kit.
Be sure to follow the child safety seat
manufacturer’s instructions.
Tighten the anchor according to
specifications. Otherwise, the safety seat
may not be properly secured and the child may be
injured in a sudden stop or collision.
82
Starting
PREPARING TO START YOUR VEHICLE
Engine starting is controlled by the ignition system.
This system meets all Canadian Interference-Causing
Equipment standard requirements regulating the
impulse electrical field strength of radio noise.
When starting a fuel-injected engine, avoid pressing
the accelerator before or during starting. Only use
the accelerator when you have difficulty starting the
engine. For more information on starting the vehicle,
refer to Starting the engine in this chapter.
Extended idling at high engine speeds can
produce very high temperatures in the
engine and exhaust system, creating the risk of
fire or other damage.
Do not park, idle, or drive your vehicle in
dry grass or other dry ground cover. The
emission system heats up the engine compartment
and exhaust system, which can start a fire.
Do not start your vehicle in a closed garage
or in other enclosed areas. Exhaust fumes
can be toxic. Always open the garage door before
you start the engine. See Guarding against
exhaust fumes in this chapter for more
instructions.
If you smell exhaust fumes inside your
vehicle, have your dealer inspect your
vehicle immediately. Do not drive if you smell
exhaust fumes.
83
Starting
Important safety precautions
A computer system controls the engine’s idle
revolutions per minute (RPM). When the engine
starts, the idle RPM runs faster to warm the engine.
If the engine idle speed does not slow down
automatically, have the vehicle checked. Do not
allow the vehicle to idle for more than ten minutes
at high engine RPM.
Before starting the vehicle:
1. Make sure all vehicle occupants have buckled
their safety belts. For more information on safety
belts and their proper usage, refer to the Seating
and safety restraints chapter.
2. Make sure the headlamps and vehicle accessories
are off.
If starting a vehicle with an automatic transmission:
• Make sure the
parking brake is set.
•
If
•
•
Make sure the gearshift is in P (Park).
starting a vehicle with a manual transmission:
Make sure the parking brake is set.
Push the clutch
pedal to the floor.
84
Starting
3. Turn the key to 4
(ON) without turning
the key to 5 (START).
4
3
5
2
1
50
40
C
60 70
80 100 120
2
100
160
40
20
120
MPH
5
SELECT/RESET
7
1
L
6
0
km/h
H
0 0 0 0 0 0 .0
FUEL DOOR
F
L
AIR THEFT
BAG
60
50
40
C
H
30
SERVICE
ENGINE
SOON
LOW
FUEL
70 80 90 100
40
220
130
240
20
MPH
km/h
ABS
4
3
200
10
O/D
OFF
H
BRAKE
!
P
5
RPMX1000
120 140
110
100
160
80
180 120
60
20
2
6
0
8
1
7
L
H
140
150
SELECT/RESET
0 0 0 0 0 0 .0
FUEL DOOR
E
RPMX1000
180110
20
10
E
4
3
80
90
140
60
30
H
F
L
AIR THEFT
BAG
SERVICE
ENGINE
SOON
LOW
FUEL
O/D
OFF
ABS
H
BRAKE
!
P
Make sure the corresponding lights illuminate briefly.
If a light fails to illuminate, have the vehicle
serviced.
light
• If the driver’s safety belt is fastened, the
may not illuminate.
85
Starting
STARTING THE ENGINE
1. Turn the key to 5
(START) without
pressing the
accelerator pedal and
release as soon as the
engine starts. The key
will return to 4 (ON).
4
3
5
2
1
2. If the temperature is above –12°C (10°F) and the
engine does not start within five seconds on the first
try, turn the key to OFF, wait ten seconds and try
again.
3. If the temperature is below –12°C (10°F) and the
engine does not start in fifteen seconds on the first
try, turn the key OFF and wait ten seconds and try
again. If the engine does not start in two attempts,
depress the accelerator and start the engine while
holding the accelerator down to the floor. Release
the accelerator when the engine starts.
4. After idling for a few seconds, apply the brake
and release the parking brake.
Using the engine block heater (if equipped)
An engine block heater warms the engine coolant,
which improves starting, warms up the engine faster
and allows the heater-defroster system to respond
quickly. Use of an engine block heater is strongly
recommended if you live in a region where
temperatures reach –23°C ( –10°F) or below.
For best results, plug the heater in at least three
hours before starting the vehicle. Using the heater
for longer than three hours will not harm the engine,
so the heater can be plugged in the night before
starting the vehicle.
To prevent electrical shock, do not use your
heater with ungrounded electrical systems
or two-pronged (cheater) adapters.
86
Starting
Guarding against exhaust fumes
Although odorless and colorless, carbon monoxide is
present in exhaust fumes. Take precautions to avoid
its dangerous effects.
If you ever smell exhaust fumes of any kind
inside your vehicle, have your dealer inspect
and fix your vehicle immediately. Do not drive if
you smell exhaust fumes. These fumes are harmful
and could kill you.
Have the exhaust and body ventilation systems
checked whenever:
• the vehicle is raised for service.
• the sound of the exhaust system changes.
• the vehicle has been damaged in a collision.
Engine exhaust, some of its constituents,
and certain vehicle components contain or
emit chemicals known to the State of California to
cause cancer, and birth defects or other
reproductive harm.
Important ventilating information
If the engine is idling while the vehicle is stopped in
an open area for long periods of time, open the
windows at least 2.5 cm (one inch).
Adjust the heating or air conditioning (if equipped)
to bring in fresh air.
Improve vehicle
ventilation by keeping
all air inlet vents clear
of snow, leaves and
other debris.
87
Driving
BRAKES
Your service brakes are self-adjusting. Refer to the
scheduled maintenance guide for scheduled
maintenance.
Occasional brake noise is normal and often does not
indicate a performance concern with the vehicle’s
brake system. In normal operation, automotive brake
systems may emit occasional or intermittent squeal
or groan noises when the brakes are applied. Such
noises are usually heard during the first few brake
applications in the morning; however, they may be
heard at any time while braking and can be
aggravated by environmental conditions such as
cold, heat, moisture, road dust, salt or mud. If a
“metal-to-metal,” “continuous grinding” or
“continuous squeal” sound is present while braking,
the brake linings may be worn-out and should be
inspected by a qualified service technician.
Anti-lock brake system (ABS) (if equipped)
On vehicles equipped with an anti-lock braking
system (ABS), a noise from the hydraulic pump
motor and pulsation in the pedal may be observed
during ABS braking events. Pedal pulsation coupled
with noise while braking under panic conditions or
on loose gravel, bumps, wet or snowy roads is
normal and indicates proper functioning of the
vehicle’s anti-lock brake system. The ABS performs a
self-check at 17 km/h (10 mph) after you start the
engine and begin to drive away. A brief mechanical
noise may be heard during this test. This is normal.
If a malfunction is found, the ABS warning light will
come on. If the vehicle has continuous vibration or
shudder in the steering wheel while braking, the
vehicle should be inspected by a qualified service
technician.
88
Driving
The ABS operates by
detecting the onset of
wheel lockup during
brake applications
and compensating for
this tendency. The
wheels are prevented
from locking even
when the brakes are firmly applied. The
accompanying illustration depicts the advantage of
an ABS equipped vehicle (on bottom) to a non-ABS
equipped vehicle (on top) during hard braking with
loss of front braking traction.
ABS warning lamp
The ABS warning lamp in the instrument cluster
momentarily illuminates when the ignition is turned
on and the engine is off. If the light does not
illuminate momentarily at start up, remains on or
continues to flash, the ABS needs to be serviced.
With the ABS light on,
BRAKE
the anti-lock brake
!
P
system is disabled and
normal braking is still
effective unless the brake warning light also remains
illuminated with parking brake released. (If your
brake warning lamp illuminates, have your vehicle
serviced immediately).
Using ABS
• In an emergency or when maximum efficiency
from the ABS is required, apply continuous full
force on the brake. The ABS will be activated
immediately, thus allowing you to retain full
steering control of your vehicle and, providing
there is sufficient space, will enable you to avoid
obstacles and bring the vehicle to a controlled
stop.
• The Anti-Lock system does not decrease the time
necessary to apply the brakes or always reduce
89
Driving
stopping distance. Always leave enough room
between your vehicle and the vehicle in front of
you to stop.
• We recommend that you familiarize yourself with
this braking technique. However, avoid taking any
unnecessary risks.
Hydraulic brake booster system (Hydroboost)
The Hydroboost system receives fluid pressure from
the power steering pump to provide power assist
during braking.
The sound of the pump operating may be heard by
the driver, but this is a normal characteristic of the
system.
For Hydroboost-equipped vehicles operating under
normal conditions, the noise of the fluid flowing
through the booster may be heard whenever the
brake is applied. This condition is normal. Vehicle
service is not required.
If braking performance or pedal response becomes
very poor, even when the pedal is strongly
depressed, it may indicate the presence of air in the
hydraulic system or leakage of fluid. Stop the vehicle
safely as soon as possible and seek service
immediately.
Parking brake
Apply the parking
brake whenever the
vehicle is parked. To
set the parking brake,
apply the brake pedal
and pull the handle up
as far as possible.
The BRAKE warning
BRAKE
lamp in the instrument
!
P
cluster illuminates and
remains illuminated
(when the ignition is turned ON) until the parking
brake is released.
90
Driving
The parking brake is not recommended to stop a
moving vehicle. However, if the normal brakes fail,
the parking brake can be used to stop your vehicle
in an emergency. Since the parking brake applies
only the rear brakes, the vehicle’s stopping distance
will increase greatly and the handling of your vehicle
will be adversely affected.
Always set the parking brake fully and make
sure that the gearshift is securely latched in
P (Park) (automatic transmission) or in 1 (First)
(manual transmission).
Your brake handle may
need to be pulled up
slightly to release
pressure before
pushing in the button.
Push the button on the
end of the parking
brake and push the handle down as far as possible
to release the brake. Driving with the parking brake
on will cause the brakes to wear out quickly and
reduce fuel economy.
TRACTION CONTROLY (IF EQUIPPED)
Your vehicle may be equipped with the optional
Traction Controly system. This system helps you
maintain the stability and steerability of your
vehicle. It is especially useful on slippery and/or hilly
road surfaces. The system operates by detecting and
controlling wheel spin. The system borrows many of
the electronic and mechanical elements already
present in the anti-lock braking system (ABS).
Wheel-speed sensors allow excess rear wheel spin to
be detected by the Traction Controly portion of the
ABS computer. Any excessive wheel spin is
controlled by automatically applying and releasing
the rear brakes in conjunction with engine torque
reductions. Engine torque reduction is realized via
91
Driving
the fully electronic spark and fuel injection systems.
This process is very sensitive to driving conditions
and very fast acting. The rear wheels “search” for
optimum traction several times a second and
adjustments are made accordingly.
The Traction Controly system will allow your
vehicle to make better use of available traction on
slippery surfaces. The system is a driver aid which
makes your vehicle easier to handle primarily on
snow, ice covered and gravel roads.
During Traction Controly operation, the traction
control active light will illuminate, you may hear an
electric motor type of sound coming from the engine
compartment and the engine will not “rev-up” when
you push further on the accelerator. This is normal
system behavior.
The Traction Controly on/off switch, located in front
of the gearshift, illuminates when the system is OFF.
The Traction Controly system will revert to the ON
position every time the ignition is turned OFF and
ON.
If you should become stuck in snow or ice or on a
very slippery road surface, try switching the Traction
Controly system off. This may allow excess wheel
spin to “dig” the vehicle out and enable a successful
“rocking” maneuver.
STEERING
Your vehicle is equipped with power steering. Power
steering uses energy from the engine to help steer
the vehicle.
To prevent damage to the power steering pump:
• Never hold the steering wheel to the extreme
right or the extreme left for more than a few
seconds when the engine is running.
• Do not operate the vehicle with a low power
steering pump fluid level.
92
Driving
If the power steering system breaks down (or if the
engine is turned off), you can steer the vehicle
manually, but it takes more effort.
If the steering wanders or pulls, the condition could
be caused by any of the following:
• underinflated tire(s) on any wheel(s)
• high crown in center of road
• high crosswinds
• wheels out of alignment
• loose or worn components in steering linkage
AUTOMATIC TRANSMISSION OPERATION
(IF EQUIPPED)
Brake-shift interlock
This vehicle is equipped with a brake-shift interlock
feature that prevents the gearshift from being moved
from P (Park) unless the brake pedal is depressed.
If you cannot move the gearshift out of P (Park)
with the brake pedal depressed:
1. Apply the parking brake, turn ignition key to
LOCK, then remove the key.
2. Insert the key and turn it to OFF. Apply the brake
pedal and shift to N (Neutral).
3. Start the vehicle.
If it is necessary to use the above procedure to
move the gearshift, it is possible that a fuse has
blown or the vehicle’s brakelamps are not operating
properly. Refer to Fuses and relays in the Roadside
emergencies chapter.
Do not drive your vehicle until you verify
that the brakelamps are working.
If your vehicle gets stuck in mud or snow it may be
rocked out by shifting from forward and reverse
gears, stopping between shifts, in a steady pattern.
93
Driving
Press lightly on the accelerator in each gear.
Do not rock the vehicle for more than a few
minutes. The transmission and tires may be
damaged or the engine may overheat.
Always set the parking brake fully and make
sure the gearshift is latched in P (Park).
Turn off the ignition whenever you leave your
vehicle.
If the parking brake is fully released, but the
brake warning lamp remains illuminated, the
brakes may not be working properly. See your
dealer or a qualified service technician.
Driving with a 4–speed automatic transmission
(if equipped)
Understanding gearshift positions
Pull the gearshift lever towards you and downward
to move the automatic gearshift.
Hold the brake pedal down while you move
the gearshift lever from P (Park) to another
position. If you do not hold the brake pedal down,
your vehicle may move unexpectedly and injure
someone.
94
Driving
P (Park)
Always come to a
complete stop before
shifting into P (Park).
Make sure the gearshift
is securely latched in P
(Park). This position
locks the transmission
and prevents the rear
wheels from turning.
Always set the parking brake fully and make
sure the gearshift is securely latched in P
(Park).
Never leave your vehicle unattended while it
is running.
R (Reverse)
With the gearshift in R
(Reverse), the vehicle
will move backward.
Always come to a
complete stop before
shifting into and out of
R (Reverse).
95
Driving
N (Neutral)
With the gearshift in N
(Neutral), the vehicle
can be started and is
free to roll. Hold the
brake pedal down while
in this gear.
(Overdrive)
The normal driving
position for the best
fuel economy.
Transmission operates
in gears one through
four.
(Overdrive) can be
deactivated by pressing
the transmission
control switch on the
end of the gearshift
lever.
The transmission control
O/D
indicator light (TCIL)
OFF
will illuminate on the
instrument cluster.
Drive – Not shown on the display. Activate by
pressing the transmission control switch on the end
of the gearshift lever with the gearshift in the
position. The O/D OFF indicator will illuminate
on the instrument cluster. Transmission operates in
96
Driving
gears one through three.
(Drive) provides more
engine braking than
(Overdrive) and is useful
when:
• driving with a heavy load
• towing a trailer up or down steep hills
• additional engine braking is desired. If towing a
trailer, refer to Driving while you tow in the
Trailer Towing chapter.
(Overdrive) mode, press the
To return to
transmission control switch. The O/D OFF indicator
will no longer be illuminated.
Each time the vehicle is started, the transmission
will automatically return to normal overdrive mode.
Every time the vehicle is shut off and restarted, you
must press the transmission control switch to cancel
overdrive operation if driving in overdrive is not
desired.
2 (Second)
Use 2 (Second) to
start-up on slippery
roads or to provide
additional engine
braking on downgrades.
1 (First)
Use 1 (Low) to provide
maximum engine
braking on steep
downgrades. Upshifts
can be made by
shifting to 2 (Second)
(Overdrive).
or to
Selecting 1 (Low) at
higher speeds causes the transmission to shift to a
lower gear, and will shift to 1 (Low) after vehicle
decelerates to the proper speed.
97
Driving
MANUAL TRANSMISSION OPERATION
(IF EQUIPPED)
Using the clutch
Vehicles equipped with a manual transmission have a
starter interlock that prevents cranking the engine
unless the clutch pedal is fully depressed.
When starting a vehicle with a manual transmission,
you must:
1. Put gearshift in N
(Neutral).
1 3 5
2. Hold down brake
2 4 R
pedal.
3. Depress clutch
pedal.
4. Turn ignition to
position 5 (START) to
start the engine, let the
engine idle for a few
seconds, then shift into
gear.
5. Release the brake
pedal.
6. Release clutch slowly
while pressing down
slowly on the
accelerator pedal.
4
3
5
2
1
• Do not drive with your foot resting on the clutch
pedal and do not use the clutch to hold your
vehicle at a standstill while waiting on a hill.
These actions will seriously reduce clutch life.
98
Driving
Recommended shift speeds
Do not downshift into 1 (first) when your
vehicle is moving faster then 24 km/h (15 mph).
This will damage the clutch.
Upshift and downshift according to the following
chart:
Upshifts when accelerating
(recommended for best fuel economy)
Shift from:
1-2
18 km/h (11 mph)
2-3
31 km/h (19 mph)
3-4
48 km/h (30 mph)
4-5
64 km/h (40 mph)
Parking your vehicle
1. Disengage the
clutch, apply brake
and shift into N
(Neutral).
1
3 5
2
4
R
2. Set parking brake.
3. Shift into 1 (First).
99
Driving
4. Turn the ignition key
to position 3 (OFF).
4
3
5
2
1
Do not park your vehicle in Neutral, it may
move unexpectedly and injure someone. Use
1 (First) gear and set the parking brake fully.
Reverse
You can shift into R (Reverse) only by moving the
gearshift to the right of 5 (Fifth) gear before you
shift into R (Reverse). This is a feature that protects
you from accidentally shifting into R (Reverse) when
you downshift from 5 (Fifth).
Make sure that your vehicle is at a complete
stop before you shift into R (Reverse). Failure
to do so may damage the transmission.
To shift into R
(Reverse):
1 3 5
1. Bring your vehicle to
2 4 R
a complete stop.
2. Push the clutch
pedal all the way to the
floor.
3. Move the gearshift
all the way to the right
and pull it back into R
( Reverse).
4. Slowly release the
clutch pedal.
If R (Reverse) is not
engaged, continue to
push the clutch pedal in while you put the
100
Driving
gearshift back into Neutral. Then, release the
clutch pedal for a moment and repeat steps 2
through 4.
Removing key from ignition
• Turn the ignition key
to position 3 (OFF).
• Push the release
lever forward and
rotate the key
towards you and
remove.
TRACTION-LOK AXLE (IF EQUIPPED)
This axle provides added traction on slippery
surfaces, particularly when one wheel is on a poor
traction surface. Under normal conditions, the
Traction-Lok axle functions like a standard rear axle.
Extended use of other than the manufacturer’s
specified size tires on a Traction-Lok rear axle could
result in a permanent reduction in effectiveness.
This loss of effectiveness does not affect normal
driving and should not be noticeable to the driver.
To avoid injury, never run the engine with
one wheel off the ground, such as when
changing a tire.
VEHICLE LOADING
Before loading a vehicle, familiarize yourself with the
following terms:
• Base Curb Weight: Weight of the vehicle
including any standard equipment, fluids,
lubricants, etc. It does not include passengers or
aftermarket equipment.
101
Driving
• Payload: Combined maximum allowable weight of
cargo, passengers and optional equipment. The
payload equals the gross vehicle weight rating
minus base curb weight.
• GVW (Gross Vehicle Weight): Base curb weight
plus payload weight. The GVW is not a limit or a
specification.
• GVWR (Gross Vehicle Weight Rating):
Maximum total weight of the base vehicle,
passengers, optional equipment and cargo. The
GVWR is specific to each vehicle and is listed on
the Safety Compliance Label on the driver’s door
pillar.
• GAWR (Gross Axle Weight Rating): Carrying
capacity for each axle system. The GAWR is
specific to each vehicle and is listed on the Safety
Compliance Label on the driver’s door pillar.
• GCW (Gross Combined Weight): The combined
weight of the towing vehicle (including passengers
and cargo) and the trailer.
• GCWR (Gross Combined Weight Rating):
Maximum combined weight of towing vehicle
(including passengers and cargo) and the trailer.
The GCWR indicates the maximum loaded weight
that the vehicle is designed to tow.
• Maximum Trailer Weight Rating: Maximum
weight of a trailer the vehicle is permitted to tow.
The maximum trailer weight rating is determined
by subtracting the vehicle curb weight for each
engine/transmission combination, any required
option weight for trailer towing and the weight of
the driver from the GCWR for the towing vehicle.
• Maximum Trailer Weight: Maximum weight of a
trailer the loaded vehicle (including passengers
and cargo) is permitted to tow. It is determined
by subtracting the weight of the loaded trailer
towing vehicle from the GCWR for the towing
vehicle.
102
Driving
• Trailer Weight Range: Specified weight range
that the trailer must fall within that ranges from
zero to the maximum trailer weight rating.
Remember to figure in the tongue load of your
loaded trailer when figuring the total weight.
Do not exceed the GVWR or the GAWR
specified on the Safety Compliance
Certification Label.
Do not use replacement tires with lower load
carrying capacities than the originals because they
may lower the vehicle’s GVWR and GAWR
limitations. Replacement tires with a higher limit
than the originals do not increase the GVWR and
GAWR limitations.
The Certification Label, found on the inside pillar of
the driver’s door, lists several important vehicle
weight rating limitations. Before adding any
additional equipment, refer to these limitations. If
you are adding weight to the front of your vehicle,
(potentially including weight added to the cab), the
weight added should not exceed the Front Axle
Reserve Capacity (FARC). Additional frontal weight
may be added to the front axle reserve capacity
provided you limit your payload in other ways (i.e.
restrict the number of passengers or amount of
cargo carried).
You may add equipment throughout your vehicle if
the total weight added is equal to or less than the
Total Axle Reserve Capacity (TARC) weight. You
should NEVER exceed the Total Axle Reserve
Capacity.
Always ensure that the weight of passengers, cargo
and equipment being carried is within the weight
limitations that have been established for your
vehicle including both Gross Vehicle Weight and
Front and Rear Gross Axle Weight Rating limits.
Under no circumstance should these limitations be
exceeded. Exceeding any vehicle weight rating
103
Driving
limitation could result in serious damage to the
vehicle and/or personal injury.
TRAILER TOWING
Your vehicle is capable of towing a trailer up to
454 kg (1 000 lbs.) gross trailer weight with a
maximum tongue load of 45 kg (100 lbs.). Do not
tow a trailer until your vehicle has been driven at
least 800 km (500 miles).
Towing a trailer places an additional load on your
vehicle’s engine, transmission, axles, brakes, tires
and suspension. Inspect these components carefully
after towing.
Do not exceed the GVWR or the GAWR
specified on the Safety Compliance
Certification Label.
Towing trailers beyond the maximum
recommended gross trailer weight could
result in engine damage, transmission/axle damage,
structural damage, loss of control, and personal
injury.
Preparing to tow
Use the proper equipment for towing a trailer, and
make sure it is properly attached to your vehicle.
See your dealer or a reliable trailer dealer if you
require assistance.
Safety chains
Always connect the trailer’s safety chains to the
vehicle. To connect the trailer’s safety chains, cross
the chains under the trailer tongue and allow slack
for turning corners.
If you use a rental trailer, follow the instructions that
the rental agency gives to you.
Do not attach safety chains to the bumper.
104
Driving
Trailer brakes
Electric brakes and manual, automatic or surge-type
brakes are safe if installed properly and adjusted to
the manufacturer’s specifications. The trailer brakes
must meet local and Federal regulations.
Do not connect a trailer’s hydraulic brake
system directly to your vehicle’s brake
system. Your vehicle may not have enough braking
power and your chances of having a collision
greatly increase.
The braking system of the tow vehicle is rated for
operation at the GVWR not GCWR.
Trailer lamps
Trailer lamps are required on most towed vehicles.
Make sure your trailer lamps conform to local and
Federal regulations. See your dealer or trailer rental
agency for proper instructions and equipment for
hooking up trailer lamps.
Driving while you tow
Do not drive faster than 88 km/h (55 mph) when
towing a trailer.
Speed control may shut off if you are towing on
long, steep grades.
When towing a trailer:
• Use a lower gear when towing up or down steep
hills. This will eliminate excessive downshifting
and upshifting for optimum fuel economy and
transmission cooling.
• Anticipate stops and brake gradually.
Exceeding the GCWR rating may cause internal
transmission damage and void your warranty
coverage.
105
Driving
Servicing after towing
If you tow a trailer for long distances, your vehicle
will require more frequent service intervals. Refer to
your Scheduled Maintenance guide for more
information.
Trailer towing tips
• Practice turning, stopping and backing up in an
area before starting on a trip to get the feel of the
vehicle trailer combination. When turning, make
wider turns so the trailer wheels will clear curbs
and other obstacles.
• Allow more distance for stopping with a trailer
attached.
• The trailer tongue weight should be 10% of the
loaded trailer weight.
• After you have traveled 80 km (50 miles),
thoroughly check your hitch, electrical
connections and trailer wheel lug nuts.
• When stopped in traffic for long periods of time in
hot weather, place the gearshift in P (Park) and
increase idle speed. This aids engine cooling and
air conditioner efficiency.
• Vehicles with trailers should not be parked on a
grade. If you must park on a grade, place wheel
chocks under the trailer’s wheels.
DRIVING THROUGH WATER
Do not drive quickly through standing water,
especially if the depth is unknown. Traction or brake
capability may be limited and if the ignition system
gets wet, your engine may stall. Water may also
enter your engine’s air intake and severely damage
your engine.
If driving through deep or standing water is
unavoidable, proceed very slowly. Never drive
through water that is higher than the bottom of the
hubs.
106
Driving
Once through the water, always try the brakes. Wet
brakes do not stop the vehicle as effectively as dry
brakes. Drying can be improved by moving your
vehicle slowly while applying light pressure on the
brake pedal.
Driving through deep water where the
transmission is submerged may allow water
into the transmission and cause internal
transmission damage.
107
Roadside emergencies
HAZARD FLASHER
Use only in an emergency to warn traffic of vehicle
breakdown, approaching danger, etc. The hazard
flashers can be operated when the ignition is off.
• The hazard lights
control is located on
top of the steering
column.
• Depress hazard lights
control to activate all
hazard flashers
simultaneously.
• Depress control again to turn the flashers off.
FUEL PUMP SHUT-OFF SWITCH
After a collision, if the engine cranks but does not
start, the fuel pump shut-off switch may have been
activated. The shut-off switch is a device intended to
stop the electric fuel pump when your vehicle has
been involved in a substantial jolt.
1. Turn the ignition to the OFF position.
2. Check the fuel system for leaks.
3. If no fuel leak is apparent, reset the fuel pump
shut-off switch by pushing in the reset button.
4. Turn the ignition to the ON position. Pause for a
few seconds and return the key to the OFF position.
5. Make a further check for leaks in the fuel system.
108
Roadside emergencies
The fuel pump shut-off
switch is located on
the left side of the
trunk behind the trunk
liner.
FUSES AND RELAYS
Fuses
If electrical
components in the
vehicle are not
15
working, a fuse may
have blown. Blown
fuses are identified by a broken wire within the fuse.
Check the appropriate fuses before replacing any
electrical components.
Always replace a fuse with one that has the
specified amperage rating. Using a fuse with
a higher amperage rating can cause severe wire
damage and could start a fire.
109
Roadside emergencies
Standard fuse amperage rating and color
COLOR
CarFuse
tridge Link
Maxi
CarFuses tridge
Grey
Grey
—
—
—
Violet Violet
—
—
—
Pink
Pink
—
—
—
Tan
Tan
—
—
—
Brown Brown
—
—
—
Red
Red
—
—
—
Blue
Blue
—
—
—
Yellow Yellow Yellow
Blue
Blue
Natural Natural
—
—
—
Green Green Green
Pink
Pink
—
—
Orange Green Orange
—
—
Red
Red
Red
—
—
Blue
—
Yellow
—
—
Tan
—
Brown
—
—
Natural
—
Black
Fuse Mini
Rating Fuses
2A
3A
4A
5A
7.5A
10A
15A
20A
25A
30A
40A
50A
60A
70A
80A
Standard
Fuses
Maxi
Fuses
Passenger compartment fuse panel
The fuse panel is located below and to the left of
the steering wheel by the brake pedal. Remove the
panel cover to access the fuses.
To remove a fuse use the fuse puller tool provided
on the fuse panel cover.
110
1
2
3
4
5
7
8
9
10
11
OWNERS
MANUAL
FOR
FUSE
INFO
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
44
43
6
SEE
42
Roadside emergencies
The fuses are coded as follows:
Fuse/Relay Fuse Amp
Location
Rating
1
20A
2
20A
3
—
4
10A
5
15A
6
7
8
9
10
20A
15A
20A
—
10A
11
12
13
14
15A
—
15A
—
Description
Cigar Lighter
Engine Controls
Not Used
RH Low Beam
Headlamp
Instrument Cluster,
Traction Control Switch
Starter Motor Relay
GEM, Interior Lamps
Engine Controls
Not Used
LH Low Beam
Headlamp
Back-up Lamps
Not Used
Electronic Flasher
Not Used
111
Roadside emergencies
Fuse/Relay Fuse Amp
Description
Location
Rating
15
15A
Power Lumbar
16
—
Not Used
17
15A
Speed Control Servo,
Shift Lock Actuator
18
15A
Electronic Flasher
19
15A
Power Mirror Switch,
GEM, Anti-Theft Relay,
Power Door Locks,
Door Ajar Switches
20
15A
Convertible Top Switch
21
5A
Instrument Cluster and
Engine Control Memory
22
—
Not Used
23
15A
A/C Clutch, Defogger
Switch
24
30A
Climate Control Blower
Motor
25
25A
Luggage Compartment
Lid Release
26
30A
Wiper/Washer Motor,
Wiper Relays
27
25A
Radio
28
15A
GEM, Overdrive Cancel
Switch
29
15A
ABS Module
30
15A
DRL Module
31
10A
Data Link Connector
32
15A
Radio, CD Player, GEM
33
15A
Stop Lamp Switch,
Speed Control
Deactivation Switch
112
Roadside emergencies
Fuse/Relay Fuse Amp
Description
Location
Rating
34
20A
Instrument Cluster,
CCRM, Data Link
Connector, Securilock
Transciever Module
35
15A
Shift Lock Actuator,
PCM, Speed Control
Servo, ABS Module
36
15A
Airbag Control Module
37
10A
Adjustable Illumination
38
20A
Highbeams
39
5A
GEM
40
—
Not Used
41
15A
Brake Lamp
42
—
Not Used
43
20A CB
Power Windows
44
—
Not Used
Power distribution box
The power distribution box is located in the engine
compartment. The power distribution box contains
high-current fuses that protect your vehicle’s main
electrical systems from overloads.
Always disconnect the battery before
servicing high current fuses.
113
Roadside emergencies
14
MINI
13
MINI
15 16
MINI MINI
17 18
MINI MINI
21
22
MINI MINI
19
20
MINI MINI
25
MAXI
23
24
MINI MINI
26
MAXI
27
MAXI
28
CB
12
MAXI
11
MAXI
10
MAXI
9
MAXI
8
MAXI
7
MAXI
6
MAXI
5
MAXI
4
MAXI
3
MAXI
2
MAXI
1
MAXI
29
DIODE
Always replace the cover to the Power
Distribution Box before reconnecting the
battery or refilling fluid reservoirs.
1
RELAY
2
RELAY
3
RELAY
4
RELAY
CONSULTER LA GUIDE
5
RELAY
SEE OWNERS MANUAL
The high-current fuses are coded as follows.
Fuse/Relay Fuse Amp
Location
Rating
Relay 1
—
Relay 2
—
Relay 3
—
Relay 4
—
Relay 5
—
1
50A**
(4.6L), 30A
CB (3.8L)
2
30A**
3
40A**
4
5
6
114
40A**
40A**
40A**
Description
Fog Lamp Interrupt
Int. Wiper
Wiper HI/LO
Starter
Fog Lamps
Electric Cooling Fan
Motor
Headlamps
Starter Motor Relay,
Ignition Switch
Ignition Switch
Ignition Switch
Instrument Cluster, PCM
Roadside emergencies
Fuse/Relay Fuse Amp
Description
Location
Rating
7
30A**
Secondary Air Injection
(3.8L only)
8
50A**
ABS Module
9
20A**
Auxiliary Power Point
10
30A**
Parklamps
11
30A**
Rear Window Defrost
Control
12
40A**
Power Windows, Power
Locks
13
—
Not Used
14
20A*
Fuel Pump
15
10A*
Radio
16
20A*
Horn
17
20A*
Anti-Lock Brake System
18
25A*
Power Seats
19
—
Not Used
20
20A*
Generator
21
—
Not Used
22
—
Not Used
23
—
Not Used
A/C Pressure (3.8L only)
24
20A*
25
—
Not Used
26
30A**
PCM
27
20A**
DRL Module, Foglamp
Relay
28
25A CB
Convertible Top
* Mini Fuses ** Maxi Fuses
CHANGING THE TIRES
If you get a flat tire while driving, do not apply the
brake heavily. Instead, gradually decrease your
speed. Hold the steering wheel firmly and slowly
move to a safe place on the side of the road.
115
Roadside emergencies
Temporary spare tire information
Your vehicle may have a temporary spare tire. The
temporary spare tire for your vehicle is labeled as
such. It is smaller than a regular tire and is designed
for emergency use only. Replace this tire with a
full-size tire as soon as possible.
If you use the temporary spare tire
continuously or do not follow these
precautions, the tire could fail, causing you to lose
control of the vehicle, possibly injuring yourself or
others.
When driving with the temporary spare tire do not:
• exceed 80 km/h (50 mph) under any
circumstances
• load the vehicle beyond maximum vehicle load
rating listed on the Safety Compliance Label
• tow a trailer
• use tire chains
• drive through an automatic car wash, because of
the vehicle’s reduced ground clearance
• try to repair the temporary spare tire or remove it
from its wheel
• use the wheel for any other type of vehicle
Tire change procedure
To prevent the vehicle from moving when
you change a tire, be sure the parking brake
is set, then block (in both directions) the wheel
that is diagonally opposite (other side and end of
the vehicle) to the tire being changed.
If the vehicle slips off the jack, you or
someone else could be seriously injured.
116
Roadside emergencies
1. Park on a level
surface, activate hazard
flashers and set
parking brake.
2. Place gearshift lever
in P (Park) or R (manual transmission), turn engine
OFF, and block the diagonally opposite wheel.
3. Remove the spare
tire, jack and lug
wrench.
4. Loosen each wheel
lug nut one-half turn
counterclockwise but
do not remove them
until the wheel is
raised off the ground.
5. Put the jack in the
jack notch next to the
tire you are changing.
Turn the jack handle
clockwise until the
wheel is completely off
the ground.
117
Roadside emergencies
Never use the rear
differential as a
jacking point.
To lessen the
risk of personal
injury, do not put any
part of your body
under the vehicle
while changing a tire.
Do not start the
engine when your
vehicle is on the jack.
The jack is only
meant for changing
the tire.
6. Remove the lug nuts with the lug wrench.
7. Replace the flat tire with the spare tire, making
sure the valve stem is facing outward. Reinstall lug
nuts until the wheel is snug against the hub. Do not
fully tighten the lug nuts until the wheel has been
lowered.
If you are using a temporary tire, the lug nut
washers will not appear to be flush with the rim.
This is normal when using the temporary spare tire
only.
8. Lower the wheel by turning the jack handle
counterclockwise.
1
9. Remove the jack and
fully tighten the lug
nuts in the order
3
4
shown.
10. Put flat tire, jack
and lug wrench away.
5
2
Make sure jack is
fastened so it does not
rattle when you drive.
11. Unblock the wheels.
118
Roadside emergencies
12. If using a mini-spare tire, turn off the traction
control switch.
Anti-theft lug nuts (if equipped)
If your vehicle is
equipped with this
feature, one of the lug
nuts on each wheel
must be removed and replaced with a special key.
The key and registration card are attached to the lug
wrench and stored with the spare tire. If you lose
the key, send the registration card to the
manufacturer (not the dealer) to get a replacement
key. If the lug wrench/lug nut key assembly is lost,
see your nearest Ford or Lincoln/Mercury dealer
who has access to the master set of keys. Do not
use an impact wrench with the anti-theft key.
Removing the anti-theft lug nut
1. Insert the key over the locking lug nut. Make sure
you hold the key square to the lug nut. If you hold
the key at an angle, you could damage the key and
the lug nut.
2. Place the lug nut wrench over the lug nut key and
apply pressure on the key with the wrench.
3. Turn the wrench in a counterclockwise direction
to remove the lug nut.
Reinstalling the anti-theft lug nut
1. Insert the key over the locking lug nut.
2. Place the lug nut wrench over the lug nut key and
apply pressure on the key with the wrench.
3. Install the lug nut.
119
Roadside emergencies
JUMP STARTING YOUR VEHICLE
The gases around the battery can explode if
exposed to flames, sparks, or lit cigarettes.
An explosion could result in injury or vehicle
damage.
Do not push start your vehicle. You could
damage the catalytic converter.
Batteries contain sulfuric acid which can
burn skin, eyes, and clothing, if contacted.
Do not attempt to push start your vehicle.
Automatic transmissions do not have
push-start capability.
Preparing your vehicle
1. Use only a 12–volt supply to start your
vehicle.
2. Do not disconnect the battery of the disabled
vehicle as this could damage the vehicle’s electrical
system.
3. Park the booster vehicle close to the hood of the
disabled vehicle making sure the two vehicles do
not touch. Set the parking brake on both vehicles
and stay clear of the engine cooling fan and other
moving parts.
4. Check all battery terminals and remove any
excessive corrosion before you attach the battery
cables. Ensure that vent caps are tight and level.
5. Turn the heater fan on in both vehicles to protect
any electrical surges. Turn all other accessories off.
120
Roadside emergencies
Connecting the jumper cables
+
+
–
–
1. Connect the positive (+) booster cable to the
positive (+) terminal of the discharged battery.
Note: In the illustrations, lightning bolts are used
to designate the assisting (boosting) battery.
+
+
–
–
2. Connect the other end of the positive (+) cable to
the positive (+) terminal of the assisting battery.
+
+
–
–
3. Connect the negative (-) cable to the negative (-)
terminal of the assisting battery.
121
Roadside emergencies
+
+
–
–
4. Make the final connection of the negative (-)
cable to an exposed metal part of the stalled
vehicle’s engine, away from the battery and the
carburetor.
The preferred locations of an exposed metal part (to
ground the circuit) are the alternator mounting
brackets or an engine lifting eye. Do not use fuel
lines, engine rocker covers or the intake manifold as
grounding points.
Do not connect the end of the second cable
to the negative (-) terminal of the battery to
be jumped. A spark may cause an explosion of the
gases that surround the battery.
5. Be sure that the cables are clear of fan blades,
belts and other moving parts of both engines.
Jump starting
1. Start the engine of the booster vehicle and run
the engine at moderately increased speed.
2. Start the engine of the disabled vehicle.
3. Once the disabled vehicle has been started, run
both engines for a further three minutes before
disconnecting the jumper cables.
122
Roadside emergencies
Removing the jumper cables
+
–
–
+
Remove the jumper cables in the reverse order
that they were connected.
1. Remove the jumper cable from the ground metal
surface.
+
+
–
–
2. Remove the jumper cable on the negative (-)
connection of the booster vehicle’s battery.
+
+
–
–
3. Remove the jumper cable from the positive (+)
terminal of the booster vehicle’s battery.
123
Roadside emergencies
+
+
–
–
4. Remove the jumper cable from the positive (+)
terminal of the disabled vehicle’s battery.
After the disabled vehicle has been started and the
jumper cables removed, allow it to idle for several
minutes so the engine computer can relearn its idle
conditions.
WRECKER TOWING
If you need to have your vehicle towed, contact a
professional towing service or, if you are a member,
your roadside assistance center.
124
Roadside emergencies
It is recommended that your vehicle be towed with a
wheel lift or flatbed equipment.
However, on Mustang and Mustang GT models, a
slingbelt with T-hooks can also be used.
Do not tow Cobra or Convertible models with a
slingbelt. Ford Motor Company has not approved a
slingbelt towing procedure for these vehicles.
If your vehicle is to be towed from the rear using
wheel lift equipment or a slingbelt, the front wheels
must be placed on a dolly to prevent damage to the
front fascia (bumper).
A towing manual is available from Ford Motor
Company for all authorized tow truck operators.
Have your tow truck driver refer to this manual for
proper hook-up and towing procedures for your
vehicle.
125
Maintenance and care
SERVICE RECOMMENDATIONS
To help you service your vehicle:
• We highlight do-it-yourself items in the engine
compartment for easy location.
• We provide a Scheduled Maintenance Guide which
makes tracking routine service easy.
If your vehicle requires professional service, your
dealership can provide necessary parts and service.
Check your “Warranty Guide” to find out which parts
and services are covered.
Use only recommended fuels, lubricants, fluids and
service parts conforming to specifications. Motorcraft
parts are designed and built to provide the best
performance in your vehicle.
PRECAUTIONS WHEN SERVICING YOUR
VEHICLE
Be especially careful when inspecting or servicing
your vehicle.
• Do not work on a hot engine.
• When the engine is running, keep loose clothing,
jewelry or long hair away from moving parts.
• Do not work on a vehicle with the engine running
in an enclosed space, unless you are sure you
have enough ventilation.
• Keep all lit cigarettes, open flames and other lit
material away from the battery and all fuel related
parts.
If you disconnect the battery, the engine must
“relearn” its idle conditions before your vehicle will
drive properly, as explained in the Battery section in
this chapter.
126
Maintenance and care
Working with the engine off
• Automatic transmission:
1. Set the parking brake and ensure the gearshift is
securely latched in P (Park).
2. Turn off the engine and remove the key.
3. Block the wheels to prevent the vehicle from
moving unexpectedly.
• Manual transmission:
1. Set the parking brake.
2. Depress the clutch and place the gearshift in 1
(First).
3. Turn off the engine and remove the key.
4. Block the wheels to prevent the vehicle from
moving unexpectedly.
Working with the engine on
• Automatic transmission:
1. Set the parking brake and ensure the gearshift is
securely latched in P (Park).
2. Block the wheels to prevent the vehicle from
moving unexpectedly.
Do not start your engine with the air cleaner
removed and do not remove it while the
engine is running.
• Manual transmission:
1. Set the parking brake, depress the clutch and
place the gearshift in N (Neutral).
2. Block the wheels to prevent the vehicle from
moving unexpectedly.
Do not start your engine with the air cleaner
removed and do not remove it while the
engine is running.
127
Maintenance and care
OPENING THE HOOD
1. Inside the vehicle,
pull the hood release
handle located under
the bottom left corner
of the instrument
panel.
HOOD
2. Go to the front of the vehicle and release the
auxiliary latch that is located under the front center
of the hood.
3. Lift the hood and secure it with the prop rod.
128
Maintenance and care
IDENTIFYING COMPONENTS IN THE ENGINE
COMPARTMENT
3.8L OHV V6 engine
10
1
2
3
4
5
9
8
7
6
1. Engine oil filler cap
2. Engine oil dipstick
3. Brake fluid reservoir
4. Power distribution box
5. Windshield washer fluid reservoir
6. Battery
7. Power steering fluid reservoir
8. Engine coolant reservoir
9. Air filter assembly
10. Automatic transmission fluid dipstick (if
equipped)
129
Maintenance and care
4.6L SOHC V8 engine
10
1
2
3
4
9
8
7
6
5
1. Engine oil dipstick
2. Brake fluid reservoir
3. Power distribution box
4. Windshield washer fluid reservoir
5. Battery
6. Engine coolant reservoir
7. Power steering fluid reservoir
8. Engine oil filler cap
9. Air filter assembly
10. Automatic transmission fluid dipstick (if
equipped)
ENGINE OIL
Checking the engine oil
Refer to the Scheduled Maintenance Guide for the
appropriate intervals for checking the engine oil.
1. Make sure the vehicle is on level ground.
130
Maintenance and care
2. Turn the engine off and wait a few minutes for
the oil to drain into the oil pan.
3. Set the parking brake and ensure the gearshift is
securely latched in P (Park) (automatic
transmissions) or 1 (First) (manual transmissions).
4. Open the hood. Protect yourself from engine heat.
5. Locate and carefully remove the engine oil level
indicator (dipstick).
• 3.8L OHV V6 engine
MIN
MAX
• 4.6L SOHC V8
engine
MIN
MAX
6. Wipe the indicator clean. Insert the indicator fully,
then remove it again.
• If the oil level is between the MIN—MAX
marks, the oil level is acceptable. DO NOT ADD
OIL.
131
Maintenance and care
• If the oil level is
below the MIN mark,
add enough oil to
raise the level within
the MIN—MAX
range.
• Oil levels above the MAX mark may cause engine
damage. Some oil must be removed from the
engine by a service technician.
7. Put the indicator back in and ensure it is fully
seated.
Adding engine oil
1. Check the engine oil. For instructions, refer to
Checking the engine oil in this chapter.
2. If the engine oil level is not within the normal
range, add only certified engine oil of the
recommended viscosity. Remove the engine oil filler
cap and use a funnel to pour the engine oil into the
opening.
3. Recheck the engine oil level. Make sure the oil
level is not above the F in FULL mark on the
dipstick.
132
Maintenance and care
Engine oil and filter recommendations
Look for this
certification mark.
Ford oil specification is WSS-M2C153-G.
Use SAE 5W-30 motor oil certified for gasoline
engines by the American Petroleum Institute.
Do not use supplemental engine oil additives, oil
treatments or engine treatments. They are
unnecessary and could, under certain conditions,
lead to engine damage which is not covered by your
warranty.
Change your engine oil and filter according to the
appropriate schedule listed in the Scheduled
Maintenance Guide.
Ford production and aftermarket (Motorcraft) oil
filters are designed for added engine protection and
long life. If a replacement oil filter is used that does
not meet Ford material and design specifications,
startup engine noises or knock may be experienced.
It is recommended you use the appropriate
Motorcraft oil filter (or another brand meeting Ford
specifications) for your engine application.
BRAKE FLUID
Checking and adding brake fluid
Brake fluid should be checked and refilled as
needed. Refer to the Scheduled Maintenance Guide
for the service interval schedules:
133
Maintenance and care
• 3.8L OHV V6 engine
• 4.6L SOHC V8
engine
1. Clean the reservoir cap before removal to prevent
dirt or water from entering the reservoir.
2. Visually inspect the
fluid level.
3. If necessary, add
brake fluid until the
level reaches MAX. Do
not fill above this line.
4. Use only a DOT 3 brake fluid certified to meet
Ford specifications. Refer to Lubricant
specifications in the Capacities and specifications
chapter.
MAX
Brake fluid is toxic.
134
Maintenance and care
If you use a brake fluid that is not DOT 3,
you will cause permanent damage to your
brakes.
Do not let the reservoir for the master
cylinder run dry. This may cause the brakes
to fail.
CLUTCH ADJUSTMENT (IF EQUIPPED)
Check the clutch
adjustment. Refer to
the Scheduled
Maintenance Guide for
the service interval
schedules.
The clutch on your
vehicle is operated by a
cable. As necessary, adjust the clutch as described
below.
1. Turn the engine off and shift into 1 (First).
2. Put your foot under the clutch pedal and gently
pull it up until the pedal stops.
3. Push the clutch pedal down slowly. You will hear a
click as the clutch adjusts itself.
135
Maintenance and care
WINDSHIELD WASHER FLUID
Checking and adding washer fluid
Check the washer fluid
whenever you stop for
fuel. The reservoir is
highlighted with a
symbol.
If the level is low, add
enough fluid to fill the
reservoir. In very cold
weather, do not fill the
reservoir all the way.
Do not put engine coolant in the container
for the windshield washer fluid.
136
Maintenance and care
ENGINE COOLANT
• 3.8L OHV V6 engine
• 4.6L V8 engine
Check the level of the engine coolant in the
reservoir. Refer to the Scheduled Maintenance Guide
for service interval schedules. Be sure to read and
understand Precautions when servicing your
vehicle in this chapter.
If the engine coolant has not been checked at the
recommended interval, the engine coolant reservoir
may become empty. If this occurs, add engine
coolant to the coolant reservoir. For more
information on engine coolant maintenance, refer to
Adding engine coolant in this chapter.
Automotive fluids are not interchangeable; do not
use engine coolant, antifreeze or windshield washer
fluid outside of its specified function and vehicle
location.
137
Maintenance and care
Adding engine coolant
Do not put engine coolant in the container
for the windshield washer fluid.
Do not mix conventional green coolant, orange
coolant or recycled coolants together in your
vehicle. Use only the type of coolant that your
vehicle was originally equipped with. If you are
unsure which type of coolant your vehicle
requires, contact your local dealer.
If sprayed on the windshield, engine coolant could
make it difficult to see through the windshield.
When the engine is cool, add a 50/50 mixture of
engine coolant and water to the engine coolant
reservoir—DO NOT ADD DIRECTLY TO THE
RADIATOR. Add straight water only in an emergency,
but you should replace it with a 50/50 mixture of
coolant and distilled water as soon as possible.
Check the coolant level in the coolant reservoir the
next few times you drive the vehicle. If necessary, add
enough of a 50/50 mixture of coolant and water to
bring the liquid level to the fill line on the reservoir.
Never remove the coolant reservoir cap
while the engine is running or hot.
If you must remove the coolant reservoir cap, follow
these steps to avoid personal injury:
1. Before you remove the cap, turn the engine off
and let it cool.
2. When the engine is cool, wrap a thick cloth
around the cap. Slowly turn cap counterclockwise
until pressure begins to release.
3. Step back while the pressure releases.
4. When you are sure that all the pressure has been
released, use the cloth to turn it counterclockwise
and remove the cap.
138
Maintenance and care
Change your engine coolant according to the
appropriate schedule listed in the Scheduled
Maintenance Guide.
Before adding engine coolant, check the color of the
coolant in your vehicle.
For vehicles with green coolant, use Ford
Premium Cooling System Fluid E2FZ-19549–AA (in
Canada, Motorcraft CXC-8–B) or an equivalent
premium engine coolant that meets Ford
specification ESE-M97B44–A.
Do not add orange coolant or recycled coolant
to your vehicle originally equipped with
conventional green coolant.
For vehicles with orange coolant, use Ford
Extended Life Engine Coolant F6AZ-19544–AA or a
DEX-COOLt equivalent that meets Ford
specification WSS-M97B44–D.
Do not add conventional green coolant or
recycled coolant to your vehicle originally
equipped with orange coolant.
Do not use alcohol or methanol antifreeze or any
engine coolants mixed with alcohol or methanol
antifreeze. Do not use supplemental coolant
additives in your vehicle. These additives may harm
your engine cooling system. The use of an improper
coolant may void your warranty of your vehicle’s
engine cooling system.
Recycled engine coolant
Ford Motor Company recommends that Ford and
Lincoln-Mercury dealers use recycled engine coolant
produced by Ford-approved processes.
For vehicles with green coolant, not all coolant
recycling processes produce coolant which meets
Ford specification ESE-M97B44–A, and use of such
coolant may harm engine and cooling system
components.
139
Maintenance and care
For vehicles with orange coolant, no recycling
process has been approved at this time and use of
such coolant may harm engine and cooling system
components.
Always dispose of used automotive fluids in a
responsible manner. Follow your community’s
regulations and standards for recycling and disposing
of automotive fluids.
Coolant refill capacity
To find out how much fluid your vehicle’s cooling
system can hold, refer to Refill capacities in the
Capacities and specifications chapter.
Have your dealer check the engine cooling system
for leaks if you have to add more than 1.0 liter
(1.0 quart) of engine coolant per month.
Severe winter climate
If you drive in extremely cold climates (less than
–36°C [–34°F]), it may be necessary to increase the
coolant concentration above 50%. Refer to the chart
on the coolant container to ensure the coolant
concentration in your vehicle is such that the
coolant will not freeze at the temperature level in
which you drive during winter months. Never
increase the engine coolant concentration above
60%. Leave a 50/50 mixture of engine coolant and
water in your vehicle year-round in non-extreme
climates.
CHECKING AND ADDING POWER STEERING
FLUID
Check the power steering fluid. Refer to the
Scheduled Maintenance Guide for the service
interval schedules. If adding fluid is necessary, use
only MERCONtV ATF.
140
Maintenance and care
FILL HOT
If your vehicle is
equipped with the
3.8L V6 engine, check
the power steering
fluid level with the
engine at normal
operating temperature.
1. Start the engine and
let it run until it
reaches normal
operating temperature
(the engine coolant
temperature gauge
indicator will be near
the center of the
normal area between H
and C).
2. While the engine idles, turn the steering wheel
left and right several times.
3. Turn the engine off.
4. Check the fluid level on the dipstick. It should be
within the FULL HOT range. Do not add fluid if the
level is within this range.
5. If the fluid is low, add fluid in small amounts,
continuously checking the level until it reaches the
correct operating range. Be sure to put the cap back
on the reservoir.
141
Maintenance and care
If your vehicle is
equipped with a 4.6L
V8 engine, check the
power steering fluid
level with the engine at
ambient temperature.
Allow at least one-half
hour after driving for
the power steering
fluid to cool.
1. Start the engine and
allow the engine to
idle.
MAX
MIN
2. Turn the steering
wheel left and right
several times.
3. Turn the engine off.
4. Check the fluid level in the reservoir. It should be
between the MIN and MAX lines. Do not add fluid if
the level is within this range.
5. If the fluid is low, add fluid in small amounts,
continuously checking the level until it reaches the
correct operating range. Be sure to put the cap back
on the reservoir.
TRANSMISSION FLUID
Checking automatic transmission fluid
Refer to your Scheduled Maintenance Guide for
scheduled intervals for fluid checks and changes.
Your transmission does not consume fluid. However,
the fluid level should be checked if the transmission
is not working properly, i.e., if the transmission slips
or shifts slowly or if you notice some sign of fluid
leakage.
Automatic transmission fluid expands when warmed.
To obtain an accurate fluid check, drive the vehicle
until it is at normal operating temperature
(approximately 30 km [20 miles]). If your vehicle has
142
Maintenance and care
been operated for an extended period at high
speeds, in city traffic during hot weather or pulling a
trailer, the vehicle should be turned off for about
30 minutes to allow fluid to cool before checking.
1. Drive the vehicle 30 km (20 miles) or until it
reaches normal operating temperature.
2. Park the vehicle on a level surface and engage the
parking brake.
3. With the parking brake engaged and your foot on
the brake pedal, start the engine and move the
gearshift lever through all of the gear ranges. Allow
sufficient time for each gear to engage.
4. Latch the gearshift lever in P (Park) and leave the
engine running.
5. Remove the dipstick, wiping it clean with a clean,
dry lint free rag.
6. Install the dipstick making sure it is fully seated in
the filler tube.
7. Remove the dipstick and inspect the fluid level.
The fluid should be in the designated area for
normal operating temperature (H) or ambient
temperature (C).
Low fluid level
Do not drive the
vehicle if the fluid level
is at the bottom of the
dipstick and the ambient temperature is above 10°C
(50°F).
Correct fluid level
The transmission fluid should be checked at normal
operating temperature 66°C-77°C (150°F-170°F) on
a level surface. The normal operating temperature
can be reached after approximately 30 km
(20 miles) of driving.
You can check the fluid without driving if the
ambient temperature is above 10°C (50°F). However,
if fluid is added at this time, an overfill condition
143
Maintenance and care
could result when the vehicle reaches normal
operating temperature.
The transmission fluid
should be in this range
if at normal operating
temperature (66°C-77°C [150°F-170°F]).
The transmission fluid
should be in this range
if at ambient
temperature (10°C-35°C [50°F-95°F]).
High fluid level
Fluid levels above the
safe range may result
in transmission failure.
An overfill condition of transmission fluid may cause
shift and/or engagement concerns and/or possible
damage.
High fluid levels can be caused by an overheating
condition.
Adjusting automatic transmission fluid levels
Before adding any fluid, make sure the correct type
is used. The type of fluid used is normally indicated
on the dipstick and/or dipstick handle and also in
the Lubricant specifications section in the
Capacities and specifications chapter.
Use of a non-approved automatic transmission
fluid may cause internal transmission
component damage.
If necessary, add fluid in 250 mL (1/2 pint)
increments through the filler tube until the level is
correct.
If an overfill occurs,
excess fluid should be
removed by a qualified
technician.
144
Maintenance and care
An overfill condition of transmission fluid may
cause shift and/or engagement concerns and/or
possible damage.
Checking and adding manual transmission fluid
1. Clean the filler plug.
2. Remove the filler
plug and inspect the
fluid level.
3. Fluid level should be
at bottom of the
opening.
4. Add enough fluid
through the filler
opening so that the
fluid level is at the
bottom of the opening.
5. Install and tighten the fill plug securely.
Use only fluid that meets Ford specifications. Refer
to the Capacities and specifications chapter.
145
Maintenance and care
BATTERY
Your vehicle is
equipped with a
Motorcraft
maintenance-free
battery which normally
does not require
additional water during
its life of service.
However, for severe usage or in high temperature
climates, check the battery electrolyte level. Refer to
the Scheduled Maintenance Guide for the service
interval schedules.
Keep the electrolyte level in each cell up to the
“level indicator”. Do not overfill the battery
cells.
If the electrolyte level in the battery is low, you can
add plain tap water to the battery, as long as you do
not use hard water (water with a high mineral or
alkali content). If possible, however, try to only fill
the battery cells with distilled water. If the battery
needs water often, have the charging system
checked.
If your battery has a cover/shield, make sure it
is reinstalled after the battery has been
cleaned or replaced.
For longer, trouble-free operation, keep the top of
the battery clean and dry. Also, make certain the
battery cables are always tightly fastened to the
battery terminals.
If you see any corrosion on the battery or terminals,
remove the cables from the terminals and clean with
a wire brush. You can neutralize the acid with a
solution of baking soda and water.
146
Maintenance and care
Batteries normally produce explosive gases
which can cause personal injury. Therefore,
do not allow flames, sparks or lighted substances
to come near the battery. When working near the
battery, always shield your face and protect your
eyes. Always provide proper ventilation.
When lifting a plastic-cased battery,
excessive pressure on the end walls could
cause acid to flow through the vent caps, resulting
in personal injury and/or damage to the vehicle or
battery. Lift the battery with a battery carrier or
with your hands on opposite corners.
Keep batteries out of reach of children.
Batteries contain sulfuric acid. Avoid contact
with skin, eyes or clothing. Shield your eyes when
working near the battery to protect against
possible splashing of acid solution. In case of acid
contact with skin or eyes, flush immediately with
water for a minimum of 15 minutes and get
prompt medical attention. If acid is swallowed, call
a physician immediately.
Because your vehicle’s engine is electronically
controlled by a computer, some control conditions
are maintained by power from the battery. When the
battery is disconnected or a new battery is installed,
the engine must relearn its idle and fuel trim
strategy for optimum driveability and performance.
To begin this process:
1. Set your parking brake.
2. Put the gearshift in P (Park) (automatic
transmission) or the neutral position (manual
transmission), turn off all accessories and start the
engine.
3. Let the engine idle for at least one minute.
147
Maintenance and care
AD
LE
RN
TU
RE
4. The relearning process will automatically
complete as you drive the vehicle.
• The vehicle may need to be driven 16 km
(10 miles) or more to relearn the idle and fuel
trim strategy.
• If you do not allow the engine to relearn its idle
trim, the idle quality of your vehicle may be
adversely affected until the idle trim is eventually
relearned.
If the battery has been disconnected or a new
battery has been installed, the clock and the preset
radio stations must be reset once the battery is
reconnected.
• Always dispose of
automotive batteries
in a responsible
manner. Follow your
local authorized
standards for
disposal. Call your
RECYCLE
local authorized
recycling center to find out more about recycling
automotive batteries.
WINDSHIELD WIPER BLADES
Check the wiper blades at least twice a year or when
they seem less effective. Substances such as tree sap
and some hot wax treatments used by commercial
car washes reduce the effectiveness of wiper blades.
Checking the wiper blades
If the wiper blades do not wipe properly, clean both
the windshield and wiper blades using undiluted
windshield wiper solution or a mild detergent. Rinse
thoroughly with clean water. To avoid damaging the
blades, do not use fuel, kerosene, paint thinner or
other solvents.
148
Maintenance and care
Changing the wiper blades
To replace the wiper blades:
1. Pull the wiper arm
away from the
windshield and lock
into the service
position.
2. Turn the blade at an
angle from the wiper
arm. Push the lock pin
manually to release the
blade and pull the
wiper blade down
toward the windshield
to remove it from the arm.
3. Attach the new wiper to the wiper arm and press
it into place until a click is heard.
INFORMATION ABOUT TIRE QUALITY GRADES
New vehicles are fitted
with tires that have
their Tire Quality
Grade (described
below) molded into the
tire’s sidewall. These
Tire Quality Grades are
determined by
standards that the
United States Department of Transportation has set.
Tire Quality Grades apply to new pneumatic tires for
use on passenger cars. They do not apply to deep
tread, winter-type snow tires, space-saver or
temporary use spare tires, tires with nominal rim
diameters of 10 to 12 inches or limited production
tires as defined in Title 49 Code of Federal
Regulations Part 575.104(c)(2).
U.S. Department of Transportation-Tire quality
grades: The U.S. Department of Transportation
requires Ford to give you the following information
149
Maintenance and care
about tire grades exactly as the government has
written it.
Treadwear
The treadwear grade is a comparative rating based
on the wear rate of the tire when tested under
controlled conditions on a specified government test
course. For example, a tire graded 150 would wear
one and one-half (1 1/2) times as well on the
government course as a tire graded 100. The relative
performance of tires depends upon the actual
conditions of their use, however, and may depart
significantly from the norm due to variations in
driving habits, service practices, and differences in
road characteristics and climate.
Traction AA A B C
The traction grades, from highest to lowest are AA,
A, B, and C. Those grades represent the tire’s ability
to stop on wet pavement as measured under
controlled conditions on specified government test
surfaces of asphalt and concrete. A tire marked C
may have poor traction performance.
The traction grade assigned to this tire is
based on straight-ahead braking traction
tests, and does not include acceleration, cornering,
hydroplaning or peak traction characteristics.
Temperature A B C
The temperature grades are A (the highest), B, and
C, representing the tire’s resistance to the
generation of heat and its ability to dissipate heat
when tested under controlled conditions on a
specified indoor laboratory test wheel. Sustained
high temperature can cause the material of the tire
to degenerate and reduce tire life, and excessive
temperature can lead to sudden tire failure. The
grade C corresponds to a level of performance which
all passenger car tires must meet under the Federal
150
Maintenance and care
Motor Vehicle Safety Standard No. 109. Grades B
and A represent higher levels of performance on the
laboratory test wheel than the minimum required by
law.
The temperature grade for this tire is
established for a tire that is properly inflated
and not overloaded. Excessive speed,
underinflation, or excessive loading, either
separately or in combination, can cause heat
buildup and possible tire failure.
SERVICING YOUR TIRES
Checking the tire pressure
• Use an accurate tire pressure gauge.
• Check the tire pressure when tires are cold, after
the vehicle has been parked for at least one hour
or has been driven less than 5 km (3 miles).
• Adjust tire pressure to recommended
specifications found on the tire pressure label
inside the glove compartment door.
Improperly inflated tires can affect vehicle
handling and can fail suddenly, possibly
resulting in loss of vehicle control.
Tire rotation
Because your vehicle’s tires perform different jobs,
they often wear differently. To make sure your tires
wear evenly and last longer, rotate them as indicated
in the Schedule maintenance guide. If you notice
that the tires wear unevenly, have them checked.
151
Maintenance and care
• 15 or 16 inch four
tire rotation
• 17 inch four tire
rotation
Replacing the tires
Replace the tires when
the wear band is
visible through the tire
treads.
Failure to follow these precautions may
adversely affect the handling of the vehicle
and make it easier for the driver to lose control
and roll over.
152
Maintenance and care
Tires that are larger or smaller than your vehicle’s
original tires may also affect the accuracy of your
speedometer.
SNOW TIRES AND CHAINS
Driving too fast for conditions creates the
possibility of loss of vehicle control. Driving
at very high speeds for extended periods of time
may result in damage to vehicle components.
Snow tires must be the same size and grade
as the tires you currently have on your
vehicle.
The tires on your vehicle have all weather treads to
provide traction in rain and snow. However, in some
climates, you may need to use snow tires and
chains. Use chains on the tires only in an emergency
or if the law requires them.
Follow these guidelines when using snow tires and
chains:
• Chains may damage aluminum wheels.
• Use only Cable Type chains with size P225/55R16
or 245/45ZR17 tires. Use of SAE Class S chains
may damage vehicle.
• SAE Class S chains may be used on P205/65R15
tires.
• Install chains securely, verifying that the chains do
not touch any wiring, brake lines or fuel lines.
• Drive cautiously. If you hear the chains rub or
bang against your vehicle, stop and re-tighten the
chains. If this does not work, remove the chains
to prevent damage to your vehicle.
• If possible, avoid fully loading your vehicle.
• Remove the tire chains when they are no longer
needed. Do not use tire chains on dry roads.
153
Maintenance and care
• The suspension insulation and bumpers will help
prevent vehicle damage. Do not remove these
components from your vehicle when using snow
tires and chains.
WHAT YOU SHOULD KNOW ABOUT
AUTOMOTIVE FUELS
Important safety precautions
Do not overfill the fuel tank. The pressure in
an overfilled tank may cause leakage and
lead to fuel spray and fire.
If you do not use the proper fuel cap, the
pressure in the fuel tank can damage the
fuel system or cause it to work improperly in a
collision.
The fuel system may be under pressure. If
the fuel cap is venting vapor or if you hear a
hissing sound, wait until it stops before completely
removing the cap.
Automotive fuels can cause serious injury or
death if misused or mishandled.
Observe the following guidelines when handling
automotive fuel:
• Extinguish all
smoking materials
and any open flames
before fueling your
vehicle.
• Always turn off the
vehicle before
fueling.
154
Maintenance and care
• Automotive fuels can be harmful or fatal if
swallowed. Fuel such as gasoline is highly toxic
and if swallowed can cause death or permanent
injury. If fuel is swallowed, call a physician
immediately, even if no symptoms are immediately
apparent. The toxic effects of fuel may not be
visible for hours.
• Avoid inhaling fuel vapors. Inhaling too much fuel
vapor of any kind can lead to eye and respiratory
tract irritation. In severe cases, excessive or
prolonged breathing of fuel vapor can cause
serious illness and permanent injury.
• Avoid getting fuel liquid in your eyes. If fuel is
splashed in the eyes, remove contact lenses (if
worn), flush with water for 15 minutes and seek
medical attention. Failure to seek proper medical
attention could lead to permanent injury.
• Fuels can also be harmful if absorbed through the
skin. If fuel is splashed on the skin and/or
clothing, promptly remove contaminated clothing
and wash skin thoroughly with soap and water.
Repeated or prolonged skin contact with fuel
liquid or vapor causes skin irritation.
• Be particularly careful if you are taking
“Antabuse” or other forms of disulfiram for the
treatment of alcoholism. Breathing gasoline
vapors, or skin contact could cause an adverse
reaction. In sensitive individuals, serious personal
injury or sickness may result. If fuel is splashed
on the skin, promptly wash skin thoroughly with
soap and water. Consult a physician immediately
if you experience an adverse reaction.
Fuel Filler Cap
Your fuel tank filler cap has an indexed design with
a one-eighth turn on/off feature.
When fueling your vehicle:
1. Turn the engine off.
155
Maintenance and care
2. Carefully turn the filler cap counterclockwise 1/8
of a turn until it stops.
3. Pull to remove the cap from the fuel filler pipe.
4. To install the cap, align the tabs on the cap with
the notches on the filler pipe.
5. Turn the filler cap clockwise 1/8 of a turn until it
stops.
If the “Service Engine Soon/Check Engine” indicator
comes on and stays on when you start the engine,
the fuel filler cap may not be properly installed.
Turn off the engine, remove the fuel filler cap and
reinstall it being careful to align the cap properly.
If you must replace the fuel filler cap, replace
it with a genuine Ford or Motorcraft part. The
customer warranty may be void for any damage
to the fuel tank or fuel system if a genuine
Ford or Motorcraft fuel filler cap is not used.
The fuel system may be under pressure. If
the fuel filler cap is venting vapor or if you
hear a hissing sound, wait until it stops before
completely removing the fuel filler cap. Otherwise,
fuel may spray out and injure you or others.
If you do not use the proper fuel filler cap,
the pressure in the fuel tank can damage
the fuel system or cause it to work improperly in a
collision.
Choosing the right fuel
Use only UNLEADED FUEL. The use of leaded fuel
is prohibited by law and could damage your vehicle.
Do not use gasolines containing methanol. It can
damage critical fuel systems components.
Vehicles certified to meet California emission
standards (indicated on the underhood Vehicle
156
Maintenance and care
Emissions Control Information label) are designed to
operate on California cleaner-burning, low-sulfur
gasolines. If you have a California-certified vehicle
and California cleaner-burning gasoline is not
available when you refuel, your engine should
perform adequately. However, the performance of
the emission control devices and systems may be
adversely affected. In New York and Massachusetts,
which have adopted California’s emission standards
without requiring the sale of California
cleaner-burning gasoline, repairs to correct the
effects of using non-California fuel may not be
covered by the emissions warranty.
Your vehicle was not designed to use fuel or fuel
additives with metallic compounds, including
manganese-based compounds containing (MMT).
Repairs to correct the effects of using a fuel for
which your vehicle was not designed may not be
covered by your warranty.
Octane recommendations
Your vehicle is
designed to use
“Regular” unleaded
gasoline with an
(R+M)/2 octane rating of 87. We do not recommend
the use of gasolines labeled as “Regular” that are
sold with octane ratings of 86 or lower in high
altitude areas.
Do not be concerned if your engine sometimes
knocks lightly. However, if it knocks heavily under
most driving conditions while you are using fuel with
the recommended octane rating, see your dealer or
a qualified service technician to prevent any engine
damage.
87
(R+M)/2 METHOD
Fuel quality
If you are experiencing starting, rough idle or
hesitation driveability problems during a cold start,
try a different brand of “Regular” unleaded gasoline.
157
Maintenance and care
“Premium” unleaded gasoline is not recommended
(particularly in the United States) because it may
cause these problems to become more pronounced.
If the problems persist, see your dealer or a qualified
service technician.
The American Automobile Manufacturers Association
(AAMA) issued a fuel specification to provide
information on high quality fuels that optimize the
performance of your vehicle. We recommend the use
of fuels that meet the AAMA specification if they are
available.
It should not be necessary to add any aftermarket
products to your fuel tank if you continue to use a
high-quality fuel.
Cleaner air
Ford approves the use of gasolines to improve air
quality, including reformulated gasolines that contain
oxygenates up to 10% ethanol or 15% MTBE.
Running out of fuel
Avoid running out fuel because this situation may
have an adverse affect on modern powertrain
components.
If you have run out of fuel:
• You may need to crank the engine several times
before the system starts to pump fuel from the
tank to the engine.
• Your “Service Engine Soon” light may come on.
For more information on the “Service Engine
Soon” light, refer to the Instrumentation chapter.
Fuel Filter
Your vehicle is equipped with a fuel filter that is
mounted on the underbody.
For fuel filter replacement, see your dealer or a
qualified service technician. Refer to the Scheduled
Maintenance Guide for the appropriate intervals for
changing the fuel filter.
158
Maintenance and care
If you replace the fuel filter, replace it with an
authorized Motorcraft part. The customer
warranty may be void for any damage to the
fuel system if an authorized Motorcraft fuel
filter is not used.
ESSENTIALS OF GOOD FUEL ECONOMY
Measuring techniques
Your best source of information about actual fuel
economy is you, the driver. You must gather
information as accurately and consistently as
possible. Fuel expense, frequency of fillups or fuel
gauge readings are NOT accurate as a measure of
fuel economy. We do not recommend taking fuel
economy measurements during the first 1 600 km
(1 000 miles) of driving (engine break-in period).
You will get a more accurate measurement after
3 000 km–5 000 km (2 000 miles–3 000 miles).
The advertised fuel capacity of the fuel tank on your
vehicle is equal to the rated refill capacity of the fuel
tank as listed in the Refill Capacities chart in this
“Owner Guide.” The advertised capacity is the
amount of the Indicated Capacity and the Empty
Reserve combined. Indicated Capacity is the
difference in the amount of fuel in a full tank and a
tank when the fuel gauge indicates empty. Empty
Reserve is the small amount of usable fuel remaining
in the fuel tank after the fuel gauge indicates empty.
The amount of Empty Reserve varies and
should not be relied upon to increase driving
range. When refueling your vehicle after the
fuel gauge indicates empty, you might not be
able to refuel the full amount of the advertised
capacity of the fuel tank due to the empty
reserve still present in the tank.
159
Maintenance and care
Filling the tank
For consistent results:
• Use the same filling rate setting (low — medium
— high) each time the tank is filled.
• Allow three automatic click-offs when filling.
• Always use the recommended octane rating of a
known quality gasoline, preferably a national
brand.
• Use the same side of the same pump and have
the vehicle facing the same direction each time
you fill up.
• Have the vehicle loading and distribution the
same every time.
Your results will be most accurate if your filling
method is consistent.
Calculating fuel economy
1. Fill the fuel tank completely and record the initial
odometer reading.
2. Each time you fill the tank, record the amount of
fuel added (in liters or gallons).
3. After at least three to five tank fill-ups, fill the
fuel tank and record the current kilometer (mileage)
reading.
4. Follow one of the simple calculations in order to
determine fuel economy:
Multiply liters used by 100, then divide by total
kilometers traveled.
Divide total miles traveled by total gallons used.
Keep a record for at least one month and record the
type of driving (city or highway). This will provide
an accurate estimate of the vehicle’s fuel economy.
Additionally, keeping records during summer and
winter will show how temperature impacts fuel
economy. In general, lower temperatures give lower
fuel economy.
160
Maintenance and care
Driving style — good driving and fuel economy
habits
Give consideration to the lists that follow and you
may be able to change a number of variables and
improve your fuel economy.
Habits
• Smooth, moderate operation can yield up to 10%
savings in fuel.
• Steady speeds without stopping will usually give
the best fuel economy.
• Idling for long periods of time (greater than one
minute) may waste fuel.
• Anticipate stopping; slowing down may eliminate
the need to stop.
• Sudden or hard accelerations may reduce fuel
economy.
• Slow down gradually.
• Drive at reasonable speeds (traveling at 105 km /h
[65 mph] uses 15% more fuel than traveling at
88 km/h [55 mph]).
• Revving the engine before turning it off may
reduce fuel economy.
• Use of the air conditioner or defroster may reduce
fuel economy.
• Use of speed control (if equipped) may improve
fuel economy. Speed control can help maintain a
constant speed and reduce speed changes. You
may want to turn off the speed control in hilly
terrain as unnecessary shifting between third and
fourth gears may occur and could result in
reduced fuel economy.
• Warming up a vehicle on cold mornings is not
required and may reduce fuel economy.
• Resting your foot on the brake pedal while driving
may reduce fuel economy.
161
Maintenance and care
• Combine errands and minimize stop-and-go
driving.
Maintenance
• Keep tires properly inflated and use only
recommended size.
• Operating a vehicle with the wheels out of
alignment will reduce fuel economy.
• Use recommended engine oil. Refer to Lubricant
Specifications.
• Perform all regularly scheduled maintenance
items. Follow the recommended maintenance
schedule and owner maintenance checks found in
your vehicle Scheduled Maintenance Guide.
Conditions
• Heavily loading a vehicle or towing a trailer may
reduce fuel economy at any speed.
• Carrying unnecessary weight may reduce fuel
economy (approximately 2 km/h [1 mpg] is lost
for every 180 kg [400 lb] of weight carried).
• Adding certain accessories to your vehicle (for
example bug deflectors, rollover/light bars,
running boards, ski/luggage racks) may reduce
fuel economy.
• Use of fuel blended with alcohol may lower fuel
economy.
• Fuel economy may decrease with lower
temperatures during the first 12–16 km
(8–10 miles) of driving.
• Flat terrain driving improves fuel economy over
hilly roads.
• Transmissions give their best fuel economy when
operated in the top cruise gear and with steady
pressure on the gas pedal.
• Close windows for high speed driving.
162
Maintenance and care
EPA window sticker
Every new vehicle should have the EPA window
sticker. Contact your dealer if the window sticker is
not supplied with your vehicle. The EPA window
sticker should be your guide for the fuel economy
comparisons with other vehicles.
It is important to note the box in the lower left
corner of the window sticker. These numbers
represent the Range of Km/L (MPG) expected on
the vehicle, depending upon the driver’s method of
operation and conditions.
EMISSION CONTROL SYSTEM
Your vehicle is equipped with various emission
control components and a catalytic converter which
will enable your vehicle to comply with applicable
exhaust emission standards. To make sure that the
catalytic converter and other emission control
components continue to work properly:
• Use only unleaded fuel.
• Avoid running out of fuel.
• Do not turn off the ignition while your vehicle is
moving, especially at high speeds.
• Have the items listed in your Scheduled
Maintenance Guide performed according to the
specified schedule.
The scheduled maintenance items listed in the
Scheduled Maintenance Guide are essential to the
life and performance of your vehicle and to its
emissions system.
If other than Ford, Motorcraft or Ford-authorized
parts are used for maintenance replacements or for
service of components affecting emission control,
such non-Ford parts should be equivalent to genuine
Ford Motor Company parts in performance and
durability.
163
Maintenance and care
Do not park, idle, or drive your vehicle in
dry grass or other dry ground cover. The
emission system heats up the engine compartment
and exhaust system, which can start a fire.
Illumination of the charging system warning light,
“Service Engine Soon” light or the temperature
warning light, fluid leaks, strange odors, smoke or
loss of oil pressure, could indicate that the emission
control system is not working properly.
Exhaust leaks may result in entry of harmful
and potentially lethal fumes into the
passenger compartment.
Do not make any unauthorized changes to your
vehicle or engine. By law, vehicle owners and anyone
who manufactures, repairs, items, sells, leases,
trades vehicles, or supervises a fleet of vehicles are
not permitted to intentionally remove an emission
control device or prevent it from working.
Information about your vehicle’s emission system is
on the Vehicle Emission Control Information Decal
located on or near the engine. This decal identifies
engine displacement and gives some tune up
specifications.
Please consult your “Warranty Guide” for complete
emission warranty information.
Readiness for inspection/maintenance (I/M)
testing
In some localities, it may be a legal requirement to
pass an I/M test of the on-board diagnostic (OBD-II)
system. If your “Check Engine/Service Engine Soon”
light is on, refer to the description in the Warning
Lights and Chimes section of the Instrumentation
chapter. Your vehicle may not pass the I/M test with
the “Check Engine/Service Engine Soon” light on.
164
Maintenance and care
If the vehicle’s powertrain system or its battery has
just been serviced, the OBD-II system is reset to a
“not ready for I/M test” condition. To ready the
OBD-II system for I/M testing, a minimum of
30 minutes of city and highway driving is necessary
as described below:
• First, at least 10 minutes of driving on an
expressway or highway.
• Next, at least 20 minutes driving in stop-and-go,
city-type traffic with at least four idle periods.
Allow the vehicle to sit for at least eight hours
without starting the engine. Then, start the engine
and complete the above driving cycle. The engine
must warm up to its normal operating temperature.
Once started, do not turn off the engine until the
above driving cycle is complete.
EXTERIOR BULBS
Replacing exterior bulbs
Check the operation of the following lamps
frequently:
• Headlamps
• Tail lamps
• Brakelamps
• High-mount brakelamp
• Turn signals
• Backup lamps
• License plate lamp
Do not remove lamp bulbs unless they will be
replaced immediately. If a bulb is removed for an
extended period of time, contaminants may enter
the lamp housings and affect performance.
165
Maintenance and care
Replacing headlamp bulbs
Handle a halogen headlamp bulb carefully
and keep out of children’s reach. Grasp the
bulb only by its plastic base and do not touch the
glass. The oil from your hand could cause the bulb
to break the next time the headlamps are
operated.
To remove the headlamp bulb:
1. Make sure headlamp switch is in OFF position,
then open the hood.
2. At the back of the
headlamp, pull two
retainer pins up to
release the headlamp
assembly.
3. Pull headlamp
assembly forward
disengaging the lamp
from the rear hidden snap retainers to expose the
back of the bulb.
4. Release clip and
disconnect the
electrical connector
from the bulb.
5. Remove the bulb
retaining ring by
rotating it
counterclockwise
(when viewed from the
rear) about 1⁄4 turn to
free it from the bulb socket, and slide the ring off
the plastic base. Keep the ring to retain the new
bulb.
6. Without turning, remove the old bulb from the
lamp assembly by gently pulling it straight out of the
lamp assembly.
166
Maintenance and care
To install the new bulb:
1. With the flat side of
the new bulb’s plastic
base facing upward,
insert the glass end of
the bulb into the lamp
assembly. You may
need to turn the bulb left or right to align the
grooves in the plastic base with the tabs in the lamp
assembly. When the grooves are aligned, push the
bulb into the lamp assembly until the plastic base
contacts the rear of the lamp assembly.
2. Install the bulb retaining ring over the plastic base
until it contacts the rear of the socket by rotating
clockwise until you feel a “stop.”
3. Connect the electrical connector into the plastic
base until it snaps, locking it into position.
4. Install the headlamp on vehicle by aligning the
lamp with the rear snap retainer, push to seat and
secure with two retainer pins.
5. Turn the headlamps on and make sure they work
properly. If the headlamp was correctly aligned
before you changed the bulb, you should not need to
align it again.
Replacing front parking lamp/turn signal bulbs
1. Make sure the headlamp control is in the OFF
position.
2. Open the hood.
3. At the back of the
headlamp, pull two
retainer pins up to
release the headlamp
assembly.
4. Pull headlamp
assembly forward
disengaging the lamp
from the rear snap retainer to expose the back of
the bulb.
167
Maintenance and care
5. Rotate the bulb
socket counterclockwise
about 1⁄4 turn and
remove from lamp
assembly.
6. Carefully pull the
bulb straight out from
the socket and push in
the new bulb.
7. To complete installation, follow the removal
procedure in reverse order.
High-mount brakelamp bulbs
1. Open trunk.
2. Inside trunk, locate
access hole under the
luggage compartment
door.
3. Remove the bulb
socket by rotating it
45 degrees and pulling
it out of the lamp
assembly.
4. Carefully pull bulb straight out of socket and push
in new bulb.
5. To complete installation, follow the removal
procedure in reverse order.
Replacing foglamp bulbs
The halogen bulb contains gas under pressure.
The bulb may shatter if the glass envelope is
scratched or if the bulb is dropped. Handle the
bulb carefully. Grasp the bulb only by its base.
Avoid touching the glass envelope.
168
Maintenance and care
1. Rotate the foglamp
bulb counterclockwise
and remove from
foglamp (the rear side
of the foglamp is
shown).
2. Disconnect the
electrical connector
from the foglamp bulb.
3. Connect the electrical connector to the new
foglamp bulb.
4. Install the foglamp bulb in foglamp by rotating
clockwise.
Replacing license plate lamp bulbs
To change the license plate bulbs:
1. Open trunk and
remove bulb socket
from the trunk lid by
turning
counterclockwise.
2. Pull the bulb straight
out of the socket and
push in the new bulb.
3. Install the bulb socket in trunk lid by turning
clockwise.
Replacing tail lamp/backup bulbs
For bulb replacement, see a dealer or qualified
technician.
Interior bulbs
Check the operation of the following interior bulbs
frequently:
• interior overhead lamp
• map lamp
169
Maintenance and care
Map lamps
For bulb replacement, see a qualified service
technician or your dealer.
Using the right bulbs
Function
Trade Number
Tail lamp, brakelamp, turn lamp 3157K
Park lamp, turn lamp, side
3157NAK
marker (front)
Backup lamp
3156K
License plate lamp
168
High-mount brakelamp
906
Headlamps
9007
Luggage compartment lamp
906
Dome lamp
575
Map lamp
575
Visor vanity lamp
74
Glove compartment
194
Rearview mirror map lamps
192
Fog lamp
899
To replace all instrument panel lights - see your
dealer.
AIMING THE HEADLAMPS
The alignment of your headlamps should be checked
if:
• Oncoming motorists frequently signal you to
deactivate your high beams, and your high beams
are not activated.
• The headlamps do not seem to provide enough
light for clear night vision.
• The headlamp beams are pointed substantially
away from a slightly down and to the right
position.
170
Maintenance and care
Vertical aim adjustment
1. Park the vehicle on
a level surface
approximately
7.6 meters (25 feet)
from a vertical wall or
screen directly in front
of it.
2. Measure the height
from the center of your
headlamp to the
ground and mark an
2.4 meters (8 foot)
horizontal reference line on the vertical wall or
screen at this height (a piece of masking tape works
well). The center of the lamp is marked by a 3.0 mm
circle on the headlamp lens.
3. Turn on the low beam headlamps to illuminate the
wall or screen and open the hood.
4. On the wall or screen you will observe a distinct
line of high intensity light. If this is not centered on
the horizontal reference line, the beam will need to
be adjusted.
5. Locate the vertical adjuster on each headlamp,
then use a 6 mm wrench or screwdriver to turn the
adjuster either counterclockwise (to adjust up) or
clockwise (to adjust down) centering the light on
the horizontal reference line.
6. HORIZONTAL AIM IS NOT REQUIRED FOR THIS
VEHICLE AND IS NON-ADJUSTABLE.
7. Close the hood and turn off the lamps.
CLEANING AND CARING FOR YOUR VEHICLE
Refer to the “Customer Assistance Guide” for a list
of Ford-approved cleaners, polishes and waxes.
171
Maintenance and care
Washing your vehicle
Wash your vehicle
regularly with cold or
lukewarm water. Never
use strong detergents
or soap. If your vehicle
is particularly dirty, use
a quality car wash
detergent. Always use a
clean sponge, washing
glove or similar device and plenty of water for best
results. To avoid spots, avoid washing when the
hood is still warm, immediately after or during
exposure to strong sunlight.
During winter months, it is especially important to
wash the vehicle on a regular basis. Large quantities
of dirt and road salt are difficult to remove and also
cause damage to the vehicle.
Remove any exterior accessories, such as antennas,
before entering a car wash. If you have wax applied
to the vehicle at a commercial car wash, it is
recommended that you clean the wiper blades and
windshield as described in Cleaning the wiper
blades and windshield.
After washing, apply the brakes several times to dry
them.
Waxing your vehicle
Wax when water stops beading on the surface. This
could be every three or four months, depending on
operating conditions.
Use only carnauba or synthetic-based waxes. Use
cleaning fluid or alcohol with a clean cloth to remove
any bugs and tar before waxing vehicle. Use tar
remover to remove any tar spots.
Avoid getting wax on the windshield. If you have
wax applied at a commercial car wash, it is
recommended that you clean the wiper blades and
172
Maintenance and care
windshield as described in Cleaning the wiper
blades and windshield.
Repairing paint chips
Minor scratches or paint damage from road debris
may be repaired with touch-up paint, repair foil or
aerosol paint spray from the Ford accessory line.
Observe the application instructions on the
products.
Remove particles such as bird droppings, tree sap,
insect remains, tar spots, road salt and industrial
fallout immediately.
Cleaning the wheels
Wash with the same detergent as the body of your
vehicle. Do not use acid-based or alcohol-based
wheel cleaners, steel wool, fuel or strong detergents.
Never use abrasives that will damage the finish of
special wheel surfaces. Use a tar remover to remove
grease and tar.
Cleaning the engine
Engines are more efficient when they are clean
because grease and dirt buildup keep the engine
warmer than normal. When washing:
• Take care when using a power washer to clean
the engine. The high pressure fluid could
penetrate the sealed parts and cause damage.
• Do not spray with cold water to avoid cracking
the engine block or other engine components.
173
Maintenance and care
• Cover the highlighted areas to prevent water
damage when cleaning the engine.
• Never wash or rinse the engine while it is
running; water in the running engine may cause
internal damage.
Cleaning plastic exterior parts
Use vinyl cleaner for routine cleaning. Clean with a
tar remover if necessary. Do not clean plastic parts
with thinners, solvents or petroleum-based cleaners.
Cleaning the exterior lamps
Wash with the same detergent as the exterior of
your vehicle. Use glass cleaner or tar remover if
necessary.
To avoid scratching the lamps, do not use a dry
paper towel, chemical solvents or abrasive cleaners.
Cleaning the wiper blades and windshield
If the wiper blades do not wipe properly, clean the
wiper blade rubber element with undiluted
windshield washer solution or a mild detergent. To
avoid damaging the blades, do not use fuel,
kerosene, paint thinner or other solvents.
174
Maintenance and care
If the wiper still does not wipe properly, this could
be caused by substances on the windshield such as
tree sap and some hot wax treatments used by
commercial car washes. Clean the outside of the
windshield with a non-abrasive cleanser such as the
non-abrasive Bon-Amit powder. Rinse thoroughly
with clean water. Do not use abrasive cleansers on
glass as they may cause scratches. The windshield is
clean if beads do not form when you rinse it with
water. The windshield and wiper blades should be
cleaned on a regular basis, and blades or rubber
elements replaced when worn.
Cleaning the instrument panel
Clean with a damp cloth, then dry with a dry cloth.
Avoid cleaner or polish that increases the gloss of
the upper portion of the instrument panel. The dull
finish in this area helps protect the driver from
undesirable windshield reflection.
Cleaning the interior fabric
Remove dust and loose dirt with a whisk broom or a
vacuum cleaner. Remove fresh spots immediately. Do
not use household or glass cleaners. These agents
can stain and discolor the fabric. Use a mild soap
and water solution if necessary.
Cleaning leather seats (if equipped)
To clean, simply use a soft cloth dampened with
water and a mild soap. Wipe the leather again with a
damp cloth to remove soap residue. Dry with a soft
cloth. For tougher soiling concerns, Ford
recommends using the leather cleaning kit
F8AJ-19G253–AA, which is available from your Ford
Dealer. This mild cleaner and special pad, cleans the
leather and maintains its natural beauty. Follow the
instructions on the cleaner label. Regular cleaning of
your leather upholstery helps maintain its resiliency
and color.
175
Maintenance and care
Do not use household cleaning products,
alcohol solutions, solvents or cleaners intended
for rubber, vinyl or plastics.
Cleaning and maintaining the safety belts
Clean the safety belts with a mild soap solution
recommended for cleaning upholstery or carpets. Do
not bleach or dye the belts, because these actions
may weaken the belt webbing.
Check the safety belt system periodically to make
sure there are no nicks, wear or cuts. If your vehicle
has been involved in an accident, refer to the Safety
belt maintenance section in the Seating and safety
restraints chapter.
Inside windows
Use glass cleaner for the inside windows if they
become fogged.
Convertible top and padded molding care
To avoid damage to the vinyl top and moldings, use
only an approved Ford cleaner, or equivalent. Do not
use stiff bristle brushes or abrasive materials or
cleaners.
Hot waxes applied by commercial car washes can
affect the cleanability of vinyl material.
Using high water pressure or wand-type car washes
against the convertible top and windows may cause
water leaks and possible seal damage.
Underbody
Flush the complete underside of vehicle frequently.
Keep body drain holes unplugged. Inspect for road
damage.
176
Capacities and specifications
MOTORCRAFT PART NUMBERS
Component
Air filter
Fuel filter
Battery
Oil filter
PCV valve
Spark plugs*
3.8L OHV V6
engine
FA-1611
FG-800A
BXT-59
FL-400S
EV-152
AWSF-42EE**
4.6L SOHC V8
engine
FA-1634
FG-800A
BXT-59
FL-820S
EV-98
AWSF-32PP***
* Refer to Vehicle Emissions Control Information
(VECI) decal for spark plug gap information.
**If a spark plug is removed for inspection, it must
be reinstalled in the same cylinder. Cylinders No. 1,
2 and 3 have an “EG” suffix. Cylinders No. 4, 5 and
6 have an “E” suffix. If a spark plug needs to be
replaced, use only spark plugs with the same service
part number suffix letter as shown on the engine
decal.
*** If a spark plug is removed for inspection, it must
be reinstalled in the same cylinder. Cylinders No. 1,
2, 3 and 4 have a “PG” suffix. Cylinders No. 5, 6, 7
and 8 have a “P” suffix. If a spark plug needs to be
replaced, use only spark plugs with the same service
part number suffix letter “PP” as shown on the
engine decal.
177
Capacities and specifications
REFILL CAPACITIES
Fluid
Ford Part
Name
Brake fluid High Performance
DOT 3
Motor
Vehicle
Brake Fluid
Engine oil Motorcraft
(includes
5W30
filter
Super
change)
Premium
Motor Oil
Engine
See
coolant1
footnote
Power
steering
fluid
Rear axle
lubricant2
178
Application
All
Capacity
All
4.7L
(5.0 quarts)
3.8L OHV
V6 engine
4.6L SOHC
V8 engine
3.8L OHV
V6 engine
Fill to line
on
reservoir
11.2L (11.8
quarts)
13.3L (14.1
quarts)
Motorcraft
Keep in
MERFULL HOT
CONtV
range on
ATF
dispstick
4.6L SOHC Fill to
V8 engine between
MIN and
MAX lines
on
reservoir
Motorcraft Ford 7.5
1.5L (3.25
SAE 80W90 inch conpints)
Premium
ventional
Rear Axle and
Lubricant
TractionLok
Ford 8.8
1.7L (3.75
inch conpints)
ventional
and
TractionLok
Capacities and specifications
Fluid
Fuel tank
Transmission
fluid
Ford Part
Name
N/A
Application
All
Motorcraft
MERCONtV
ATF
Automatic
with 3.8L
OHV V6
engine
Automatic
with 4.6L
SOHC V8
engine
Manual
with 3.8L
OHV V6
engine
Manual
with 4.6L
SOHC V8
engine 3
All
Motorcraft
MERCONt
ATF
Windshield
washer
fluid
Ultra-Clear
Windshield
Washer
Concentrate
Capacity
58.7L (15.5
gallons)
13.1L (13.9
quarts)
12.0L (12.8
quarts)
2.6L
(5.6 pints)
3.1L
(6.6 pints)
Fill to line
on
reservoir
1
If your engine coolant is green in color, use Ford
Premium Cooling System Fluid. If your coolant is
orange in color, use Ford Extended Life Engine
Coolant. Refer to Adding engine coolant, in the
Maintenance and Care chapter.
2
Rear axle lubricants do not need to be checked or
changed unless a leak is suspected, service is required
or the axle assembly has been submerged in water. The
axle lubricant should be changed any time the rear axle
has been submerged in water. Fill 6 mm to 14 mm
(1/4 inch to 9/16 inch) below bottom of fill hole. Add
118 ml (4 oz.) of additive friction modifier
C8AZ-19B546-A, Ford specification EST-M2C118–A for
complete refill of Traction-Lok axles.
3
Service refill capacity is determined by filling the
transmission to the bottom of the filler hole with the
vehicle on a level surface.
179
Capacities and specifications
LUBRICANT SPECIFICATIONS
Item
Ford part
name
Brake fluid High Performance
DOT 3
Motor
Vehicle
Brake Fluid
Door
Silicone
weatherLubricant
strips
Door latch,
hood latch,
auxiliary
hood latch,
door
hinges,
striker
plates, seat
tracks and
fuel filler
door hinge
Engine
coolant
Engine oil
180
MultiPurpose
Grease
Ford
Premium
Engine
Coolant
(green in
color)
Ford Extended Life
Engine Coolant (orange
in color)
Motorcraft
5W30 Super
Premium
Motor Oil
Ford part
number
C6AZ19542-AB
Ford specification
ESAM6C25-A
and DOT 3
F7AZ19G208-BA
and F5AZ19553-AA
D0AZ19584-AA
or F5AZ19G209-AA
ESRM13P4-A
E2FZ19549-AA
ESEM97B44-A
F6AZ19544-AA
ESBM1C93-B or
ESRM1C159-A
WSSM97B44-D
or DEXCOOLt
equivalent
XOWSS5W30-QSP M2C153-G
with API
Certification
Mark
Capacities and specifications
Item
Ford part
name
Lock
Penetrating
cylinders
Lubricant
Power
Motorcraft
steering
MERfluid and
CONtV
convertible ATF
top fluid
(if
equipped)
Rear axle Motorcraft
lubricant
SAE 80W90
Premium
Rear Axle
Lubricant1
Automatic Motorcraft
transmisMERCONtV
sion fluid
ATF
Manual
Motorcraft
transmisMERCONt
sion fluid
ATF
Disc brake Silicone
caliper
Brake
rails
Caliper and
Dielectric
compound
Windshield Ultra-Clear
washer
Windshield
fluid
Washer
Concentrate
Ford part Ford specinumber
fication
E8AZnone
19501-B
XT-5-QM
MERCONtV
XY80W90-QL
WSPM2C197-A
XT-5-QM
MERCONtV
XT-2-QDX
MERCONt
D7AZESE19A331-A M1C171-A
(Motorcraft
WA-10)
C9AZ19550-AC
ESRM17P5-A
1
Add 118 ml (4 oz.) of additive friction modifier
C8AZ-19B546–A, Ford specification EST-M2C118–A
for complete refill of Traction-Lok axles.
Ford design rear axles contain a synthetic lubricant
that does not require changing unless the axle has
been submerged in water.
181
Capacities and specifications
ENGINE DATA
Engine
Cubic inches
Horsepower
Torque
Recommended
fuel
Firing order
Spark plug gap
Ignition system
Compression
ratio
3.8L OHV V6
engine
232
190 @
5250 rpm
220 lb.-ft. @
2750 rpm
87 octane
4.6L SOHC V8
engine
281
260 @
5250 rpm
302 lb.-ft. @
4000 rpm
87 octane
1-4-2-5-3-6
1.3-1.4 mm
(0.05200.056 inch)
EDIS
9.4:1
1-3-7-2-6-5-4-8
1.3-1.4 mm
(0.05200.056 inch)
Coil on plug
9.0:1
VEHICLE DIMENSIONS
Vehicle
dimensions
(1) Overall
length
(2) Overall
width
(3) Overall
height
(4) Wheelbase
(5) Track - Front
(5) Track - Rear
1
2
3
4
1
1
1
1
182
358.9
361.4
521.5
526.5
mm
mm
mm
mm
Coupe
Convertible
mm (in)
mm (in)
4 653.3 (183.2) 4 653.3 (183.2)
1 856.7 (73.1)
1 856.7 (73.1)
1 353.8 (53.3)1
1 356.4 (53.4)2
2 573.0 (101.3) 2 573.0 (101.3)
1 534.2 (60.4)3 1 534.2 (60.4)3
1 539.2 (60.6)4 1 539.2 (60.6)4
(53.5
(53.6
(59.9
(60.1
in)
in)
in)
in)
for
for
for
for
Mustang
Mustang
Mustang
Mustang
GT
GT
GT
GT
Capacities and specifications
3
5
2
4
1
183
Capacities and specifications
IDENTIFYING YOUR VEHICLE
Safety compliance label
The National Highway
MFD. BY FORD MOTOR CO. IN U.S.A.
DATE: XXXXX
GVWR:XXXXX LB/ XXXXX KG
Traffic Safety
FGAWR: XXXXXX/XXXXXXX
RGAWR: XXXXXXX/XXXXXXX
THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL
Administration
MOTOR VEHICLE SAFETY STANDARDS IN EFFECT ON THE
DATE OF MANUFACTURE SHOWN ABOVE.
Regulations require
VIN: XXXXXXXXXXXXXXXXX TYPE: XXXXXXXXXXXXXXX
that a Safety
MAXIMUM LOAD=OCCUPANTS + LUGGAGE=XXXKG/XXXXLB
Compliance
OCCUPANTS: X TOTAL X FR X 2ND X RR OCCUPANTS LUGGAGE
XX XXXKG/XXXXLB
Certification Label be
TIRE: XXXX/XXXXX XXX
X XXXKG/XXXXLB
PRESSURE (FR) XXX kPa/33 PSI COLD
PRESSURE (RR) XXX kPa/33 PSI COLD
affixed to a vehicle and
EXT PNT: XXXXXX XXXXXX RC: XX DSO: XXXX F0000
prescribe where the
BAR INT TR TP/PS R AXLE TR SPR
T0000
X
XX
XXX X
XX
X XXXX
Safety Compliance
UTC ∇FOHT-15294A10-GA
Certification Label may
be located. The Safety Compliance Certification
Label is located on the front door latch pillar on the
driver’s side.
TRAILER TOWING - SEE OWNER GUIDE
Vehicle identification number
The vehicle
AIR
BAG
identification number
XXXXXXXXXXXXXXXXX
is attached to a metal
tag and is located on
the driver side
instrument panel.
Engine number
The engine number (the last eight numbers of the
vehicle identification number) is stamped on the
engine block, transmission, frame and transfer case
(if equipped).
184
Reporting safety defects
REPORTING SAFETY DEFECTS (U.S. ONLY)
If you believe that your
vehicle has a defect
that could cause a
crash, or could cause
injury or death, you
should immediately
inform the National
Highway Traffic Safety
Administration
(NHTSA) in addition to notifying Ford Motor
Company.
If NHTSA receives similar complaints, it may open
an investigation, and if it finds that a safety defect
exists in a group of vehicles, it may order a recall
and remedy campaign. However, NHTSA cannot
become involved in individual problems between
you, your dealer or Ford Motor Company.
To contact NHTSA, you may either call the Auto
Safety Hotline toll-free at 1–800–424–9393
(202–366–0123 in the Washington D.C. area) or
write to:
NHTSA
U.S. Department of Transportation
400 Seventh Street
Washington D.C. 20590
You can also obtain other information about motor
vehicle safety from the Hotline.
185
Index
Air bag supplemental
restraint system ........ 71
and child
safety seats ............. 73
description .............. 72
disposal .................... 76
indicator light ......... 75
passenger air bag ... 74
Automatic transmission
driving an automatic
overdrive .. 94,95,96,97
Axle
refill capacities ...... 178
Battery
voltage gauge .......... 15
Brakes ................... 88,90
anti-lock .............. 88,89
anti-lock brake
system (ABS)
warning light ........... 89
fluid, checking
and adding ............ 133
shift interlock .......... 93
Break-in period ........ 2,3
Child safety seats
attaching with
tether straps ........... 82
in rear seat .............. 80
tether anchorage
hardware ................. 82
Cleaning
your vehicle ............. 171
engine
compartment ......... 173
exterior ........... 173,176
exterior lamps ....... 174
interior ................... 175
plastic parts .......... 174
washing .................. 172
waxing ................... 172
wheels .................... 173
windows ................ 176
186
wiper blades .......... 174
Clutch
fluid ........................ 135
operation
while driving ........... 98
recommended shift
speeds ...................... 99
Console ...................... 52
Controls
power seat ............... 64
Convertible ................ 53
cleaning ................. 176
installation
of the boot .............. 54
lowering the
convertible top ........ 53
raising the
convertible top ........ 55
Coolant ............. 139,140
checking
and adding ............ 138
refill capacities ...... 140
Defrost
rear window ............ 17
Emission
control system ......... 163
Engine
coolant ................... 137
idle speed control . 146
service points . 129,130
starting after a
collision ................. 108
Engine block heater . 86
Engine oil
checking
and adding ............ 132
dipstick .................. 130
specifications . 130,133
Exhaust fumes .......... 87
Floor mats ................. 51
Index
Fuel
choosing
the right fuel ......... 156
comparisons with EPA
fuel economy
estimates ............... 163
detergent in fuel ... 158
filling your vehicle
with fuel ......... 154,155
gauge ....................... 12
quality .................... 157
running
out of fuel ............. 158
safety information
relating to automotive
fuels ....................... 154
Fuses ................. 109,110
Gas mileage (see
Fuel economy) ........ 159
160,161,162
Gauges ....................... 12
engine coolant
temperature gauge . 13
engine oil pressure
gauge ....................... 15
Hazard flashers ....... 108
Head restraints ......... 63
Headlamps
aiming ............. 170,171
bulb
specifications ........ 170
high beam ............ 7,44
warning chime ........ 11
Heating ...................... 18
heating and air
conditioning
system ................ 18,20
Hood ........................ 128
Ignition ..................... 182
Inspection/maintenance
(I/M) testing ............ 164
Instrument panel ........ 6
cleaning ................. 175
Keys
key in ignition
chime ....................... 11
positions of the
ignition .................... 45
removing from the
ignition .................. 101
Lamps
daytime
running light ........... 16
fog lamps ................. 52
headlamps ............... 16
headlamps, flash to
pass .......................... 44
instrument panel,
dimming ................... 17
interior
lamps ......... 49,169,170
replacing bulbs ..... 165
166,167,168,169
Lane change indicator
(see Turn signal) ...... 43
Lights, warning and
indicator
air bag ........................ 7
anti-lock brakes
(ABS) ...................... 10
anti-theft ................... 7
brake ........................ 10
charging system ........ 7
check coolant .......... 11
low fuel ...................... 9
overdrive off .............. 9
safety belt ................. 7
service engine soon .. 8
turn signal indicator . 6
Lumbar support,
seats ...................... 65,66
Manual transmission
reverse ................... 100
187
Index
Mirrors
side view mirrors
(power) ................... 51
Motorcraft parts ...... 158
Octane rating .......... 157
Odometer ................... 14
Panic alarm feature,
remote entry system 57
Parking brake ............ 90
Power distribution box
(see Fuses) ............. 113
Power door locks ...... 51
Power steering .......... 92
fluid, checking and
adding .................... 140
Radio ................ 21,22,23
24,25,26,27,28,29,30
31,32,33,34,35,36,37
38,39,40,41,42,43
Relays ...................... 109
Remote entry
system .............. 56,60,61
illuminated entry .... 58
locking/unlocking
doors ................... 56,57
replacement/additional
transmitters ............. 58
replacing
the batteries ............ 59
Safety belts (see
Safety restraints) ...... 11
Safety restraints
cleaning the safety
belts .................. 71,176
extension assembly 70
for children ........ 76,77
warning light and
chime .................. 11,70
Seat belts (see Safety
restraints) ........ 66,68,69
Seats .......................... 63
child safety seats .... 78
188
cleaning ................. 175
Seats-easy access/
easyout feature ......... 65
Servicing your
vehicle ............... 126,127
Spark plugs,
specifications ........... 177
Special notice .............. 3
Specification chart,
lubricants ................. 180
Speed control ............ 46
Speedometer ............. 13
Starting your
vehicle .............. 83,84,86
jump starting ........ 120
121,122,123
Steering wheel
tilting ....................... 45
Tachometer ............... 14
Tires ........... 149,150,151
changing ......... 115,116
checking
the pressure .......... 151
replacing ................ 152
rotating .................. 151
snow tires
and chains ............. 153
tire grades ............. 150
treadwear .............. 150
Towing
wrecker .................. 124
Traction control ........ 91
active light .............. 10
Traction-lok
rear axle .................. 101
Transmission ........... 142
automatic
operation ................. 93
fluid, checking and
adding
(automatic) ........... 142
143,144
Index
fluid, checking and
adding (manual) ... 145
manual operation .... 98
Trip odometer ........... 15
Trunk ......................... 57
Vehicle dimensions . 182
Vehicle Identification
Number (VIN) ......... 184
Vehicle loading ........ 101
104,105,106
Ventilating
your vehicle ............... 87
Warning chimes ........... 6
Washer fluid ............ 136
reservoir ................ 136
Water,
Driving through ....... 106
Wheels
anti-theft
lug nuts ................. 119
Windows .................... 50
Windshield washer
fluid and wipers
checking
and cleaning .......... 148
operation ................. 43
replacing
wiper blades .......... 149
189
190
Filling station information
Item
Recommended fuel
Fuel tank capacity
Engine oil capacity
(includes filter change)
Tire size and pressure
Hood release
Coolant capacity-3.8L
OHV V6 engine1
Coolant capacity-4.6L
SOHC V8 engine1
Power steering fluid
capacity
Manual transmission
fluid capacity-3.8L OHV
V6 engine
Manual transmission
fluid capacity-4.6L
SOHC V8 engine2
Automatic transmission
fluid capacity-3.8L OHV
V6 engine3
Automatic transmission
fluid capacity-4.6L
SOHC V8 engine3
Information
Unleaded fuel only 87 octane
58.7L (15.5 gallons)
4.7L (5.0 quarts). Use
Motorcraft 5W30 Super
Premium Motor Oil,
Ford specification
WSS-M2C153-G
See label on inside of
glove box door.
Pull handle under the
left side of the
instrument panel.
11.2L (11.8 quarts)
13.3L (14.1 quarts)
Fill to line on reservoir
or dipstick. Use
Motorcraft MERCONtV
ATF.
2.6L (5.6 pints). Use
Motorcraft MERCONt
ATF.
3.1L (6.6 pints). Use
Motorcraft MERCONt
ATF.
13.1L (13.9 quarts). Use
Motorcraft MERCONtV
ATF.
12.0L (12.8 quarts). Use
Motorcraft MERCONtV
ATF.
191
Filling station information
1
If your engine coolant is green in color, use Ford
Premium Cooling System Fluid. If your engine
coolant is orange in color, use Ford Extended Life
Engine Coolant. Refer to Adding engine coolant, in
the Maintenance and Care chapter.
2
Service refill capacity is determined by filling the
transmission to the bottom of the filler hole with the
vehicle on a level surface.
3
Ensure correct automatic transmission fluid is used
for a specific application. Check the container to
verify the fluid is MERCONt and/or MERCONtV
approved. Some fluids have been approved as
meeting both MERCONt and MERCONtV
requirements and will be labeled as such. Fluids
labeled as meeting only MERCONt or only
MERCONtV requirements must not be used
interchangeably. DO NOT mix MERCONt and
MERCONtV. Transmission fluid requirements are
indicated on the dipstick or on the dipstick handle.
Refer to your Scheduled Maintenance Guide to
determine the correct service interval.
192