Day/Night DNS Fixed
Dome Camera
NTSC / PAL
HD4D
HD4DX
User Guide
Document 800-00023 – Rev D – 05/07
Revisions
Issue
Date
Revisions
A
04/07
New document.
B
05/07
Increase line weight of illustrations.
C
05/07
Corrected specifications.
D
06/07
Changes:
Page 14, LL switch is on power supply board.
Page 18, corrected Day/Night mode explanation.
Page 24, corrected Vertical Phase Adjustment to 0 - 359°.
2
Warnings
Installation and servicing should be performed only by qualified and experienced technicians
to conform to all local codes and to maintain your warranty.
WARNING!
12 VDC/24 VAC models require the use of CSA Certified/UL Listed
Class 2 power adapters to ensure compliance with electrical safety
standards.
WEEE (Waste Electrical and Electronic Equipment). Correct disposal of
this product (applicable in the European Union and other European
countries with separate collection systems). This product should be
disposed of, at the end of its useful life, as per applicable local laws,
regulations, and procedures.
Explanation of Graphical Symbols
RISK OF
ELECTRIC SHOCK
DO NOT OPEN
THIS SYMBOL INDICATES
THAT DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
THE COVER. NO USER-SERVICEABLE
PARTS INSIDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL
THIS SYMBOL INDICATES
THAT IMPORTANT OPERATING
AND MAINTENANCE
INSTRUCTIONS ACCOMPANY
THIS UNIT.
CAUTION
Document 800-00023 Rev D
05/07
3
FCC Compliance Statement
Information to the User: This equipment has been tested and found to comply with the limits
for a Class A digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Caution
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Manufacturer’s Declaration of Conformance
The manufacturer declares that the equipment supplied with this guide is compliant with the
essential protection requirements of the EMC directive 89/336/EEC and the Low Voltage
Directive LVD 73/23 EEC, conforming to the requirements of standards EN 55013 for
emissions, EN 50130-4 for immunity, and EN 60065 for Electrical Equipment safety.
4
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Unpack Everything. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Equipment Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Mounting the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Connecting Cables Through the Housing Base . . . . . . . . . . . .8
Connecting Cables Through the Side Conduit . . . . . . . . . . . . .9
Electrical Box Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Connecting the Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Adjusting the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Line Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Adjusting the Lens Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Camera Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Camera Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
OSD Menu Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SETUP Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
SPECIAL Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Adding a Camera Title Display . . . . . . . . . . . . . . . . . . . . . . . 19
Sync Control Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Motion Detection Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Privacy Mode Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installing the Enclosure Cover . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Solving Common Technical Issues . . . . . . . . . . . . . . . . . . . . . . . . 22
Warranty and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Cable Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Document 800-00023 Rev D
05/07
5
Introduction
The unobtrusive, low-profile design of the HD4D CCTV Camera is ideal for indoor and outdoor
installations in commercial and residential venues.
Before You Begin
Please read this guide carefully before you install the HD4D CCTV Camera.
Keep this guide for future reference.
Unpack Everything
Check that the items received match those listed on the order form and packing slip. The
HD4D packing box should include, in addition to this User Guide:
•
•
•
•
One fully-assembled HD4D camera, including factory-installed pigtail power and video
connections
One HD4D hardware kit
One bag containing mounting screws
One Product warranty
If any parts are missing or damaged, contact the dealer you purchased the camera from or call
Honeywell Customer Service (see Warranty and Service).
Equipment Required
You will require the following tools to complete the installation:
•
•
•
6
Phillips screwdriver
Tools supplied in the hardware kit (three Allen keys): one for the security screw on the lid
one for the conduit plug locking screw, and one for the lens locking screw
Side-cutters
Installation
The HD4D is weather-sealed for indoor or outdoor locations. The HD4D is a fully-integrated
enclosure with camera and lens. The wiring can be completely concealed to reduce the risk of
tampering.
Figure 1
Installation Components
HD4D dome
enclosure
Document 800-00023 Rev D
05/07
7
Mounting the Camera
The HD4D Camera is designed to be surface mounted on a wall or ceiling. Before you
mount the camera, use the mounting template provided to mark and pre-drill the holes.
Connecting Cables Through the Housing Base
For installations requiring pulling cables through the grommet located in the bottom of the
base:
1.
2.
3.
Use a sharp knife to cut an ! opening in the base gasket (see the figure below). Be
careful. The opening should only be big enough to feed the cable assembly through.
Pull the cabling through the opening.
Apply appropriate sealant around the opening to prevent moisture from entering the
housing.
!
8
Base gasket opening
Connecting Cables Through the Side Conduit
1.
2.
3.
4.
5.
Peel back the bottom flat gasket below the side conduit just enough to expose the security
screw.
Use the Allen key supplied to loosen and remove the security screw (see below).
Use a flat screwdriver to unscrew the conduit plug.
Pull the cabling through the hole.
Apply appropriate sealant around the opening to prevent moisture from entering the
housing.
security screw
supplied
allen key
Document 800-00023 Rev D
05/07
9
Electrical Box Installations
Figure 2 illustrates how to mount the HD4D directly to a 4S electrical box or directly to wall
or ceiling. For 4S electrical box installations, the optional adapter plate can be used to
cover ceiling or wall imperfections around the electrical box opening.
Figure 2
4S Electrical Box Installation
Electrical box
(not supplied)
Ceiling/wall
Secure the optional
adapter plate to the
4S electrical box
using appropriate
screws (not supplied)
Secure the HD4D base with
screws appropriate to your
installation (supplied)
Adapter plate
(use is optional)
HD4D base
For surface mount
installations (without an
electrical box), use
#6-1 7/16 inch slotted Type
A screws (x4) supplied
Note
10
Honeywell recommends that you orient the conduit plug facing downwards
(wall mount installations) to prevent moisture from entering the housing.
Figure 3 illustrates how to mount the HD4D directly to a double gang or single gang
electrical box.
Figure 3
Double Gang/Single Gang Electrical Box Installation (Single Gang Shown)
Electrical box
(not supplied)
Ceiling/wall
Secure the HD4D base with
screws appropriate to your
installation (not supplied)
HD4D base
For surface mount
installations (without an
electrical box), use
#6-1 7/16 inch slotted Type
A screws (x4) supplied
Document 800-00023 Rev D
05/07
11
Connecting the Wiring
Follow Figure 4 for the wiring connection.
Figure 4
Wiring Connection
Note
Video: female BNC
(yellow)
+ Red
Power: 12 VDC
or 24 VAC
12
- Black
For secure installations, surface
mounted cables should be
protected by plastic or metal
cable covers.
Adjusting the Camera
To adjust the HD4D Camera:
1.
2.
3.
4.
Apply 12 VDC or 24 VAC power to the camera and monitor the video signal.
Loosen the screws that lock the gimbal assembly in place (see Figure 5).
Adjust the camera carrier to the desired view.
Tighten the screws to lock the gimbal assembly in place.
Note
Orient the camera as shown in Figure 5 to maintain the correct picture
orientation.
Figure 5
Gimbal Adjustment
Top view
Angle view
Locking screw. Loosen to
adjust Horizontal (B).
Setscrews (x2). Loosen to
adjust Pan (C). Other
setscrew located on
opposite side.
Locking screw
B
C
Legend
Set focal length
(bottom)
Line Lock switch Set focus
must be left in (top)
ON position.
A = Tilt rotation
B = Horizontal rotation
C = Pan rotation
A
Document 800-00023 Rev D
05/07
13
Line Lock
The Line Lock switch on the power supply board must be left in the ON position. To switch
between Line Lock and Internal Lock, use the OSD menu (see Sync Control Setup, page 19).
Adjusting the Lens Focus
Lenses are pre-focused at the factory but may require a final adjustment after installation in the
unlikely event the optical effect of the dome causes a slight defocusing of the lens.
TECH TIP! To check the focus, hold the dome over the lens while making any adjustments.
To adjust the camera direction, view angle and focus, connect the service monitor cable
(supplied) to the video monitor output.
14
Camera Settings
Camera Functions
Figure 6
Camera Controller
Legend
2
# Description
1 Video-test monitor output connector
2 Camera OSD control (four position plus center push)
LF
DN
Press this control To do this
RT
UP, DOWN
Select a new item
LEFT, RIGHT
Select a menu item
SETUP (MENU)
(CENTER PUSH)
Enter SETUP MENU,
access a submenu
1
Document 800-00023 Rev D
05/07
15
OSD Menu Structure
The HD4D camera menu system consists of one main setup menu for easy programming.
Main MENU
SETUP MENU
Sub-Menus
1
2
3
4
5
6
7
8
LENS
SHUTTER
WHITE BAL.
↵
DC
VIDEO
MANUAL
FLK (FLICKERLESS)
ESC
MANUAL
↵
ATW
MANUAL
AWC
↵
BACKLIGHT
AGC
DNR
SENS-UP
SPECIAL
EXIT MENU
16
Options
↵
↵
OFF
LOW
MIDDLE
HIGH
OFF
LOW
MIDDLE
HIGH
↵
↵
↵
OFF
LOW
MIDDLE
HIGH (with AGC in OFF mode)
OFF
AUTO! (with LENS in MANUAL
mode or SHUTTER in FLX mode)
CAMERA ID
DAY/NIGHT
SYNC
MOTION DET
PRIVACY
MIRROR
SHARPNESS
RESET
SETUP Menu
Menu Item
Option
Description
LENS
DC!
VIDEO
MANUAL
Selects Lens type. Only DC mode is supported at this time.
Caution
Selecting VIDEO or MANUAL adversely affects camera operation.
FLK
MANUAL!
ESC!
Adjusts shutter settings.
WHITE BAL
(White Balance)
ATW
MANUAL!
AWC!
Controls color on the screen.
BACKLIGHT
OFF
LOW
MIDDLE
HIGH
Provides light level control to overcome severe backlighting conditions.
AGC
OFF
LOW!
MIDDLE!
HIGH!
Adjusts value of AGC (Automatic Gain Control). Increase the GAIN level to
brighten the picture (noise/distortion may develop).
SHUTTER
FLK (Flickerless) reduces on-screen flickering.
MANUAL adjusts the shutter speed from 1/60-1/120,000 of a second (NTSC)
or 1/50-120,000 of a second (PAL). Not available in DC lens mode.
ESC (Electronic Shutter Control) adjusts the brightness level on screen. Not
available in DC lens mode.
Select ATW (Auto Tracing White Balance) when the color temp is 2400°K 12000°K; for example, under a fluorescent light, or outdoors.
MANUAL mode allows you to increase or decrease the red or blue factor on
the screen.
AWC (Auto White Balance Control) automatically adjusts the white balance to
your specific environment.
DNR (Digital
OFF
Noise Reduction) LOW
MIDDLE
HIGH
Reduces noise/distortion on the screen. Increasing the DNR level reduces
noise but may introduce video artifacts. DNR is deactivated if AGC is turned
off.
SENS-UP
(Sensitivity Up)
Automatically provides a clear image under low-light conditions. You can
control the maximum low-light magnification from 2x to 128x. Increasing
magnification may cause noise/distortion.
OFF
AUTO!
EXIT
Document 800-00023 Rev D
05/07
Exits the SETUP menu and returns to video monitoring.
17
SPECIAL Menu
On the main SETUP menu:
1.
2.
Press UP or DOWN and then select SPECIAL.
Push SETUP (MENU) to access the SPECIAL menu.
Menu Item
Option
Description
1 CAMERA ID
OFF
ON
Turns ID display off and on. To add a camera title (name and/or number) to
be displayed on the screen, see Adding a Camera Title Display.
2 DAY/NIGHT
AUTO
COLOR
BW
When set to AUTO , the camera automatically switches to Night mode
(B/W) when the light level is low.
When set to COLOR, the camera stays in Day mode (Color).
When set to BW, the camera stays in Night mode (B/W).
3 SYNC
INT
L/L
Synchronizes the vertical interval sync pulse of your camera with other
equipment to reduce the effect of picture roll on the monitor.
Select L/L (Line Lock) mode to adjust the phase from 0° to 359°.
4 MOTION DET
OFF
ON!
Detects moving objects on screen and displays MOTION DETECTED along
with the number of movements counted. Allows you to select the area on
screen you want to observe (see Motion Detection Setup).
5 PRIVACY
OFF
ON!
Allows you to mask up to 4 areas of the screen from video monitoring.
6 MIRROR
OFF
ON
Produces a horizontal mirror image on screen.
7 SHARPNESS
ON!
OFF
Sharpens the image on screen. You can adjust the sharpness level from 0 31 (excessive sharpening may cause picture noise to develop).
8 RESET
RETURN!
18
Restores all factory default settings.
Returns to the main SETUP menu.
Adding a Camera Title Display
On the SPECIAL menu, select CAMERA ID, then press SETUP (MENU)..
1.
2.
3.
4.
Press the menu control UP, DOWN, LEFT, or RIGHT
to select a character, then press (SETUP) MENU to
accept it. The character is saved and the title cursor
at the bottom of the screen moves to the next
position. Use the # $ symbols to go backward or
forward in the title name/number to make changes.
Select CLR to delete the entire title and start again.
Repeat step 1 until your camera title is complete.
Select POS to position the camera title on the
screen. Select the position using the menu control,
then press (SETUP) MENU to confirm the position.
Select END when you are finished.
CAMERA ID
ABCDEFGHIJKLM
NOPRQSTUVWXYZ
a b c d e f g h i j k l m
n o p q r s t u v w x y z
– . 0 1 2 3 4 5 6 7 8 9
# $ CLR POS END
_______________
Sync Control Setup
On the SPECIAL menu, select SYNC, then press SETUP (MENU).
Menu Item
Description
INTERNAL
When line lock is not required.
LINELOCK
Adjust the vertical phase (VPH):
RETURN
Press MENU to return to the SETUP menu.
<SYNC. CONTROL>
SYNC
INT (L/L)
VPH: 000 - 359 (factory default is 0).
Document 800-00023 Rev D
05/07
RETURN!
19
Motion Detection Setup
On the SPECIAL menu, select MOTION DET, then press SETUP (MENU).
Menu Item Option
Description
AREA SEL
AREA 1
AREA 2
AREA 3
AREA 4
Select which of the four motion
detection grids top left, top right,
bottom left, bottom right) you would
like to modify.
AREA
STATE
ON
OFF
Choose whether to activate or
deactivate the selected grid.
Press LEFT or RIGHT control to alter
the dimensions of the selected grid.
TOP
DOWN
LEFT
RIGHT
MOTION DETECTION
AREA SEL
AREA STATE
TOP
DOWN
LEFT
RIGHT
AREA 1
ON
|..|................| 10
|........|..........| 25
|...|...............| 20
|........|..........| 40
Press SET to Return
Privacy Mode Setup
On the SPECIAL menu, select PRIVACY, then press SETUP (MENU).
Menu Item
AREA SEL
Description
AREA 1
AREA 2
AREA 3
AREA 4
Select which of the four masking
grids (top left, top right, bottom
left, bottom right) you would like to
modify.
AREA STATE ON
OFF
Choose whether to activate or
deactivate the selected grid.
AREA TONE
Press LEFT or RIGHT menu
control to change the shade of the
masking grids.
TOP
DOWN
LEFT
RIGHT
Press LEFT or RIGHT menu
control to alter the dimensions of
the selected grid.
20
PRIVACY
AREA SEL
AREA STATE
AREA TONE
TOP
DOWN
LEFT
RIGHT
AREA 1
ON
|...............|...| 80
|..|................| 10
|........|..........| 25
|...|...............| 20
|........|..........| 40
Press SET to Return
Installing the Enclosure Cover
To install the enclosure cover, use the Allen key (supplied) to secure the HD4D dome
enclosure to the base with four #8-32 security screws.
Figure 7
Enclosure Cover Installation
HD4D dome enclosure
#8-32 security screws (x4)
Routine Maintenance
Use regular liquid cleaners to remove dirt and grime from the HD4VC4HR dome.
Caution
Do not use harsh or abrasive cleaners which can scratch the
polycarbonate dome and reduce visibility for the camera.
If the camera view is obstructed by scratches, remove the front plate and rotate to find an
unscratched part of the dome.
Document 800-00023 Rev D
05/07
21
Solving Common Technical Issues
No Video
❐
Check that the power supply voltage is within the operating
specifications for your camera model. See Specifications for
details.
❐
Check the video signal connections are correct.
❐
Check for a loose connection.
Fuzzy Video
❐
Check the video ground connections.
❐
Check for ground loops.
Call Honeywell Technical Support for additional assistance (see Warranty and Service).
22
Warranty and Service
Subject to the terms and conditions listed on the Product warranty, during the warranty period
Honeywell will repair or replace, at its sole option, free of charge, any defective products
returned prepaid.
In the event you have a problem with any Honeywell product, please call Customer Service at
1.800.796.CCTV for assistance or to request a Return Merchandise Authorization (RMA)
number.
Be sure to have the model number, serial number, and the nature of the problem available for
the technical service representative.
Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped to
Honeywell without a clearly identified Return Merchandise Authorization (RMA) number
may be refused.
Document 800-00023 Rev D
05/07
23
Specifications
Video Signal Specifications
Pickup device:
1/3 in. Sony Interline CCD sensor
Synchronization system:
12 VDC: Internal / 24 VAC: (Internal or Line lock)
Vertical phase adjustment:
Adjustable, 0° - 359°, OSD control
Horizontal resolution:
540 TV lines
Lens type:
3.3 - 12 mm Vari-focal Auto Iris, IR Corrected F1.5,
DC Drive
Minimum illumination response: 0.3 lux @ F1.5 (Color)
0.03 lux @ F1.5 (B/W) - Sens Up
Signal to noise ratio:
Better than 50 dB (AGC Off)
Gain control:
Automatic, selectable
Lens iris control:
DC Auto Iris type
White balance:
Selectable: ATW/AWB
Gamma:
0.45
BLC:
Low/Middle/High/Off
DNR:
High/Medium/Low
DSS:
Off/Auto (selectable limit 2X - 128X)
Privacy Function
On/Off (4 Programmable Zones)
Video output:
1 V p-p composite
Video output impedance:
75 Ohms
24
Format Specifications
NTSC
PAL
Color video signal format:
Standard
Standard
Effective picture elements:
768 (H) x 494 (V)
752 (H) x 582 (V)
Scanning system (2:1 interlace): 525 lines, 60 fields/sec.
Electronic shutter:
625 lines, 50 fields/sec.
1/60 - 1/120,000 second 1/50 - 1/120,000 second
General Specifications
Construction:
Die cast (housing) Polycarbonate (dome)
Finish:
Gray/off white powder coating
Dimensions (D) x (H):
5.5 in. x 3.6 in.(140.2 mm x 91.5 mm)
Weight:
2.5 lb. (1.1 kg) max
Power supply auto switching:
12 VDC @ 4.8 watts max.
24 VAC, 60 Hz @ 3.8 watts max.
Temperature:
Storage: -49°F to +167°F (-45°C to +75°C)
Operating: -13°F to +131°F (-25°C to +55°C)
Relative humidity:
0% to 95% RH non-condensing
Regulatory
Emissions:
FCC, CE (EN55013)
Immunity:
CE (EN50130-4)
Safety:
EU: 73/23/EEC LVD)
Environmental:
Meets IP66
Document 800-00023 Rev D
05/07
25
Cable Guidelines
Maximum Power Supply Cable Length (feet/meters)
Cameras With AC/DC Power Supplies
Wire gauge
Total load
Optional
Power supply
2.5 W
15 VDC
260/79
415/126
1055/322
1680/512
2.5 W
24 VAC
608/185
980/299
2515/767
3930/1198
3.5 W
15 VDC
180/55
290/88
730/220
1170/352
3.5 W
24 VAC
470/143
760/232
1926/587
3065/934
24 AWG
22 AWG
18 AWG
16 AWG
Note Calculations are based on an unregulated linear power supply, which
would be the worst case. Using a regulated or switching power supply
can increase the cable distance. Honeywell recommends using a CSA
Certified/UL listed Class 2 power adapter to ensure compliance with
electrical safety standards.
Maximum Video Coaxial Cable Length (feet/meters)
Cable type
RG-59
RG-6
RG-11
Wire gauge
23 AWG*
18 AWG*
16 AWG*
750/229
1500/457
2000/610
Maximum length (feet/meters)
* Copper clad steel core, 95% braided shield
26
HD4D/HD4DX Mounting Template
Document 800-00023 Rev D
05/07
27
Honeywell Video Systems (Head Office)
2700 Blankenbaker Pkwy, Suite 150
Louisville, KY 40299, USA
www.honeywellvideo.com
℡ +1.800.796.2288
Honeywell Video Systems Northern Europe
Netwerk 121
1446 WV Purmerend, The Netherlands
www.honeywell.com/security/nl
℡ +31.299.410.200
Honeywell Security Australia Pty Ltd.
Unit 5, Riverside Centre, 24-28 River Road West
Parramatta, NSW 2150, Australia
www.honeywellsecurity.com/au
℡ +61.2.8837.9300
Honeywell Video Systems UK Ltd.
Aston Fields Road, Whitehouse Ind Est
Runcorn, Cheshire, WA7 3DL, UK
www.honeywell.com/security/uk
℡ +44 (0) 1928 756999
Honeywell Security Asia Pacific
33/F Tower A, City Center, 100 Zun Yi Road
Shanghai 200051, China
www.asia.security.honeywell.com
℡ +86 21.2527.4568
Honeywell Security South Africa
Unit 6 Galaxy Park, 17 Galaxy Avenue
Linbro Park, P.O. Box 59904
2100 Kengray, Johannesburg, South Africa
www.honeywell.co.za
℡ +27.11.574.2500
Honeywell Security Asia
Flat A, 16/F, CDW Building, 388 Castle Peak Road
Tsuen Wan, N.T., Hong Kong
www.asia.security.honeywell.com
℡ +852.2405.2323
Honeywell Security France
Parc Gutenberg, 8, Voie La Cardon
91120, Palaiseau, France
www.honeywell.com/security/fr
℡ +33.01.64.53.80.40
Honeywell Security Italia SpA
Via Treviso 2 / 4
31020 San Vendemiano
Treviso, Italy
www.security.honeywell.com/it
℡ +39.04.38.36.51
Honeywell Security España
Mijancas 1. 3a Planta
P. Ind. Las Mercedes
28022 Madrid, Spain
www.security/honeywell.com/es
℡ +34.902.667.800
Honeywell Security Deutschland
Johannes-Mauthe-Straße 14
D-72458 Albstadt, Germany
www.honeywell.com/security/de
℡ +49.74 31.8 01.0
Honeywell Security Poland
Chmielewskiego 22a, 70-028
Szczecin, Polska
www.ultrak.pl
℡ +48.91.485.40.60
Honeywell Security Czech Republic
Havránkova 33, Brno
Dolní Heršpice, 619 00, Czech Republic
www.olympo.cz
℡ +420.543.558.111
Honeywell Security Slovakia Republic
Vajnorská 142, 83104 Bratislava
Slovakia
www.olympo.sk
℡ +421.2.444.54.660
www.honeywellvideo.com
+1.800.796.CCTV (North America only)
HVSsupport@honeywell.com
Document 800-00023 – Rev D – 05/07
© 2007 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from
Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However, Honeywell Video Systems cannot
assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice.
Revisions or new editions to this publication may be issued to incorporate such changes.
Download PDF

advertising