Field Controls UV-500C Air Cleaner User Manual

UV-AIRE™ AIR PURIFYING SYSTEM
Model: UV-500C
*For best results, operate
the UV-500 continuously
24 hours a day.
ITEMS INCLUDED IN SYSTEM:
1-UV-Aire™ UV-500C unit
1-Ultra Violet Lamp Individually Boxed
1-Instruction Sheet
4-10” x 10” x 1” Filters
1-Bagged Parts: containing lamp
connector, alcohol swab and
access door screw
The high intensity ultraviolet light attacks airborne mold, bacteria, and viruses. The high efficiency filter traps
allergens, dust, and pollen. The carbon filter removes odors and attacks VOC’s (volatile organic compounds).
READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE PROCEEDING WITH THE INSTALLATION
LEAVE THE INSTALLATION INSTRUCTIONS WITH THE OWNER/OPERATOR OF THE DEVICE
AFTER OPENING THE CARTON, UNPACK AND INSPECT THE UNIT AND LAMP FOR DAMAGE.
DO NOT INSTALL THIS UNIT IF ANY DAMAGE IS NOTICEABLE.
SAFETY CONSIDERATIONS
WARNING: Never expose eyes or skin to UVC light from any source.
• Looking directly at the UVC light may cause permanent eye damage or blindness.
• Never operate the UV-Aire™ Air Purifying System with the UV lamp access door open.
WARNING: DO NOT mount this unit outdoors.
• This product is designed for indoor installation only.
WARNING: To avoid electrical shock hazard, do not operate in wet environment.
I.
INDICATION FOR USE
This product is not sold as a medical device and is not for the purpose of diagnosis of any disease or condition nor for
use in the mitigation, treatment, or prevention of any disease or condition.
II.
GENERAL INFORMATION
Model
Volts
Amps
Hz
Watts
Lamp Intensity
at 1 meter
Recommended
Max Sq. Feet
Weight
UV-500C
120
.4
60
38
15 μW/cm2
500
11 Lbs
Width
Height
Depth
(Inches)
(Inches)
(Inches)
12
15
13
FEATURES
1. The UV-500C is equipped with a three speed control to allow the user to adjust the airflow through the unit
from 30 cfm to 70 cfm. Any speed is effective in rooms up to 500 square feet.
2. The UV-500C is equipped with a circuit board to monitor the operation of the UV lamp and the operation time
until the filter or lamp needs to be changed.
III.
UV-500C SET UP PROCEDURE
1.
Remove the lamp from the top carton pad.
2.
Remove the lamp connector from the bagged parts provided.
3.
Remove the UV-500C from its protective plastic bag.
WARNING: DO NOT PLUG INTO WALL OUTLET!
4.
Connect the UV lamp to the lamp connector knob (See Figure 1)
5.
Clean the lamp with the alcohol swab provided. (See Figure 2)
Figure 1
NOTE: Dirt and fingerprints will reduce lamp output and effectiveness.
6.
Open the lamp access door on the back of the unit.
Figure 2
7.
Insert the ceramic tip of the lamp into the UV port and twist the lamp connector
clockwise to lock in place. (See Figure 3)
Figure 3
8.
With unit still UNPLUGGED, insert the lamp power connector into the recessed
receptacle on the unit. (See Figure 4)
Figure 4
9.
Close the access door and install the access door screw provided in the bagged parts.
(See Figure 5)
Figure 5
WARNING: Never expose eyes or skin to UVC light from any source. Looking directly at the UVC light may cause permanent eye damage or
blindness. Never operate the UV-Aire™ Air Purifying System with the UV chamber door open. Avoid touching the glass portion of the
Page 2
lamp with your hands.
10. Slide the filter drawer out of the base. Remove one the four filters from its plastic bag
and place it in the drawer with arrow/carbon side up. (See Figure 6)
11. Slide the filter drawer with filter back into the base unit. Press firmly until drawer
catches.
NOTE: The positive catch eliminates vibration and ensures proper function of the filter.
12. Unwind the power cord from underneath the unit and insert plug into any standard 120volt outlet.
Figure 6
13. Turn the speed control knob clockwise to turn the unit on. After the fan has started, the LED lights will show a
continuous “GREEN” color and the LCD will indicate 365 days left for the lamp and 90 days for the filter. See
Figure 7)
Motor Fan
Speed Control
Knob
Lamp LED
Filter LED
Figure 7
NOTE: If the LCD display reads differently use the point of a pen or paper clip to press the “reset” button beside
the LED for either the lamp or the filter to reset the days as shown above.
IV.
OPERATION
1. Place the UV-500C in the desired area; plug the power cord into a standard 120-volt wall receptacle.
2. Turn the speed control knob clockwise to turn on the unit and to adjust the motor/fan speed to the desired airflow.
(Refer to Figure 7)
3. After the fan has started, the LED light for the lamp and filter will show a continuous “GREEN” color indicating
proper unit operation.
IV.
MAINTENANCE
1. Replace 10”x 10” intake filter every 90 days. The LED beside the filter indicator will turn
“RED” and the display will say “FILTER: CHANGE” when it is time to replace the filter.
2. Replace your UV-Aire™ Air Purifying System lamp once a year to maintain the lamps
maximum output intensity. The lamp should operate continuously for maximum lamp life
and light effectiveness. The LED beside the lamp indicator will turn “RED” and the
display will say “LAMP: CHANGE” when it is time to replace the filter.
VI.
REPLACEMENT PROCEDURES
Figure 8
REPLACING THE UV LAMP
VERY IMPORTANT: Turn the speed control switch on unit to ‘OFF’ position and unplug
unit from outlet or turn off power to the unit before replacing the UV lamp.
1. Loosen the screw on the lamp access door on the back of the UV-500C. (See Figure 8)
2. Open the door to expose the lamp connection. (See Figure 9)
Figure 9
WARNING: Never expose eyes or skin to UVC light from any source. Looking directly at the UVC light may cause permanent eye damage or
blindness. Never operate the UV-Aire™ Air Purifying System with the UV lamp access door open. Avoid touching the glass portion of the
Page 3
lamp with your hands.
3. Disconnect the lamp connection, then rotate lamp-mounting knob counter-clockwise and
pull the lamp out of the unit. (See Figure 10 & 11)
4. Remove lamp carefully, by un-plugging the lamp from the lamp-mounting knob. (See
Figure 12)
NOTE: When replacing the lamp, always wipe off lamp with the supplied alcohol wipe before
installing.
Figure 10
5. Plug the new lamp onto the lamp-mounting knob. (See Figure 12)
6. Guide the other end of the lamp through the hole in the UV chamber. (See Figure 11)
7. Secure the lamp into position by rotating the lamp-mounting knob clockwise.
8. Plug the lamp power leads back into the power connection. (See Figure 10)
NOTE: UV lamps contain a small amount of mercury, like a typical fluorescent lamp.
According to the EPA’s Universal Waste Rule, these types of lamps may be disposed of into
household waste. Check with your local waste management authority for local disposal or
recycling requirements.
Figure 11
9. Close the access door and install the access door screw. (See Figure 8)
10. Plug the power cord back into the wall receptacle or restore power to the UV-500C.
11. Use the point of a pen or paper clip to press the “reset” button beside the lamp LED. (See
Figure 13)
12. Lamp LED will turn from “RED” to “GREEN” and the display will say “LAMP: 365 DAYS”.
Figure 12
REPLACING AIR FILTERS
1. Pull the drawer out at the base of the unit and remove the old filter.
2. Remove the filter from its plastic bag and place the filter into the tray of the drawer with the
black carbon facing up.
3. Use the point of a pen or paper clip to press the “reset” button beside the filter LED.
Figure 13
4. Filter LED will turn from “RED” to “GREEN” and the display will say “FILTER: 90 DAYS”.
VII.
REPLACEMENT PARTS KIT
For replacement parts, contact your local heating service company. Any
questions, please contact Field Controls at:
PHONE: 252-522-3031
FAX: 252-522-0214 EMAIL:
SALES@FIELDCONTROLS.COM
Limited Warranty
Field Controls, L.L.C. warrants that the following Field Controls, L.L.C. products sold hereunder, shall be free from defects in material and workmanship under
normal use for eighteen (18) months from date of manufacturing by the consumer excepting the provisions numbered below. UV-LAMPS/BULBS
Field Controls, L.L.C. warrants that the following Field Controls, L.L.C. products sold hereunder, shall be free from defects in material and
workmanship under normal use for ninety (90) days from date of installation by the consumer excepting the provisions numbered below.
Provisions: 1. Field Controls shall have no obligation in the event the customer is unable to provide receipt showing the date the customer purchased the product(s)
or accurate date code information. 2. The product must be properly installed, maintained and operated under normal conditions. 3. Field Controls shall not be liable for any consequential and incidental damages, resulting from failure of a Field Controls, L.L.C. product, failure to
deliver, delay in delivery, delivery in nonconforming condition, or for any breech of contract or duty between Field Controls, L.L.C. and the customer. 4. Field Controls, L.L.C. products are often intended for use in specific applications. Field Controls, L.L.C. makes no warranty if a Field Controls, L.L.C.
product is used in applications other than intended. 5. Field Controls, L.L.C. makes no warranty of any kind in regard to any other manufacturer’s products distributed by Field Controls, L.L.C. Field Controls,
L.L.C. will pass on all warranties made by the manufacturer and where possible, will expedite the claim on behalf of the customer, but ultimately,
responsibility for disposition of the warranty claim lies with the manufacturer.
The health aspects associated with the use of these products and their ability to aid in disinfecting of environmental air have not been investigated by UL.
WARNING: Never expose eyes or skin to UVC light from any source. Looking directly at the UVC light may cause permanent eye damage or
Page
blindness. Never operate the UV-Aire™ Air Purifying System with
the4UV chamber door open. Avoid touching the glass portion of the lamp
with your hands.
Download PDF

advertising