Instruction manual | Fisher-Price V4340 Baby Monitor User Manual

®
Original Instructions
Multimo 340XC
Multimo 360
Multimo 360XC
Multimo 420
Multimo 420XC
Multimo 360XC
Multimo 420XC
Multimo 340XC
Multimo 360
Multimo 420
N
MATIO
R
O
F
IN
TANT e
R
O
P
s
IM
efore u
ference
Read bn for future re
& retai
Carton Contents
lock off
button
switchbox
Multimo 340XC
cable clip x 2
start/stop
lever
grassbox
handle
washer
x4
Easi-Reel
cable spool
cam lock x 4
bolt
barrel
nut x 4
grassbox
upper
upper
handle
roller
half x 2
lower handle x 2
grassbox
half x 2
pivot block x 2
spring x 2
electric cable
with moulded
on plug
instruction
manual
mulching
plug
lock off
button
switchbox
Multimo 360
Multimo 420
cable clip x 2
start/stop
lever
grassbox
handle
washer
x4
cam lock x 4
bolt
barrel
nut x 4
grassbox
upper
upper
handle
roller
half x 2
lower handle x 2
grassbox
half x 2
pivot block x 2
spring x 2
electric cable
with moulded
on plug
mulching
plug
PAGE 1
instruction
manual
Carton Contents
lock off
button
switchbox
Multimo 360XC
Multimo 420XC
cable clip x 2
start/stop
lever
washer
x4
grassbox
handle
cam lock x 4
bolt
upper
handle
barrel
nut x 4
lower handle x 2
Easi-Reel
cable spool
grassbox
upper
roller
half x 2
grassbox
half x 2
pivot block x 2
spring x 2
electric cable
with moulded
on plug
instruction
manual
mulching
plug
IMPORTANT !
Please check the contents of the carton are correct BEFORE assembling your new Flymo product.
The Loose Parts Pack is packaged underneath the deck of the product.
IF ANY PARTS ARE MISSING CONTACT:Husqvarna UK Ltd. Customer Service Department direct
Telephone : 0844 844 4558 UK
1800 882 350 ROI
Fax : 01325 302530
Safety
If not used properly this product can be dangerous! This product can cause serious injury to the
operator and others, the warnings and safety instructions must be followed to ensure reasonable safety
and efficiency in using this product. The operator is responsible for following the warning and safety
instructions in this manual and on the product. Never use the product unless the grassbox or guards
provided by the manufacturer are in the correct position.
Explanation of Symbols on your product
Warning
Read the user instructions carefully to
make sure you understand all the controls
and what they do.
Beware of sharp blades - remove plug from
mains before maintenance or if cable is
damaged.
Blades continue to rotate after the machine
is switched off.
Always keep the product on the ground when
operating. Tilting or lifting the product may cause
stones to be thrown out.
Keep the cable supply away from the
blade.
Keep bystanders away. Do not mow whilst
people especially children or pets are in
the area.
PAGE 2
Safety
General
1. This product is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they have
been given supervision or instruction concerning
the use of the product by a person responsible
for their safety. Children should be supervised
to ensure that they do not play with the product.
Local regulations may restrict the age of the
operator.
2. Never allow children or people unfamiliar with
the instructions to use the machine.
3. Stop using the machine while people, especially
children, or pets are nearby.
4. Only use the product in the manner and for the
functions described in these instructions.
5. Never operate the product when you are tired, ill
or under the influence of alcohol, drugs or
medicine.
6. The operator or user is responsible for accidents
or hazards occurring to other people or their
property.
Electrical
1. The British Standards Institute recommend the
use of a Residual Current Circuit Device
(R.C.D.) with a tripping current of not more than
30mA. Even with a R.C.D. installed 100% safety
cannot be guaranteed and safe working practice
must be followed at all times. Check your R.C.D.
every time you use it.
2. Before use, examine cable for damage, replace
it if there are signs of damage or ageing.
3. Do not use the product if the electric cables are
damaged or worn
4. Immediately disconnect from the mains
electricity supply if the cable is cut, or the
insulation is damaged. Do not touch the electric
cable until the electrical supply has been
disconnected. Do not repair a cut or damaged
cable. Replace it with a new one.
5. Your extension cable must be uncoiled, coiled
cables can overheat and reduce the efficiency of
your product.
6. Keep cable away from product, always work
away from the power point mowing up and
down, never in circles.
7. Do not pull cable around sharp objects.
8. Always switch off at the mains before
disconnecting any plug, cable connector or
extension cable.
9. Switch off, remove plug from mains and
examine electric supply cable for damage or
ageing before winding cable for storage. Do not
repair a damaged cable, replace it with a new
one. Use only Flymo replacement cable.
10. Always wind cable carefully, avoiding kinking.
11. Never carry the product by the cable.
12. Never pull on the cable to disconnect any of the
plugs.
13. Use only on AC mains supply voltage shown on
the product rating label.
14. Flymo Products are double insulated to
EN60335. Under no circumstance should an
earth be connected to any part of the product.
Preparation
1. While using your product always wear
substantial footwear and long trousers.
2. Make sure the lawn is clear of sticks, stones,
bones, wire and debris; they could be thrown by
the blade.
3.
4.
Before using the product and after any impact,
check for signs of wear or damage and repair as
necessary.
Replace worn or damaged blades together with
their fixings in sets to preserve balance.
Use
1. Use the product only in daylight or good artificial
light.
2. Avoid operating your product in wet grass,
where feasible.
3. Take care in wet grass, you may lose your
footing.
4. On slopes, be extra careful of your footing and
wear non-slip footwear.
5. Use across the face of slopes, never up and
down.
6. Exercise extreme caution when changing
direction on slopes. Walk never run.
7. Using on banks and slopes can be dangerous.
Do not use on banks or steep slopes.
8. Do not walk backwards when operating, you
could trip.
9. Never cut grass by pulling the product towards
you.
10. Switch off before pushing the mower over
surfaces other than grass.
11. Never operate the product with damaged guards
or without guards in place.
12. Keep hands and feet away from the blade at all
times and especially when switching on the
motor.
13. Do not tilt product when the motor is running,
except when starting and stopping. In this case,
do not tilt more than absolutely necessary and
lift only the part which is away from the operator.
Always ensure that both hands are in the
operating position before returning the product
to the ground.
14. Do not put hands near the grass discharge
chute.
15. Never pick up or carry a product when it is
operating or still connected to the mains supply.
16. Remove the plug from the mains :
before leaving the product unattended for any
period;
before clearing a blockage;
before checking, cleaning or working on the
appliance;
if you hit an object. Do not use your product
until you are sure that the entire product is in a
safe operating condition.;
if the product starts to vibrate abnormally.
Check immediately. Excessive vibration can
cause injury.
Maintenance and storage
1. Caution: Do not touch rotating blade(s)
2. Keep all nuts, bolts and screws tight to be sure
the lawnmower is in safe working condition.
3. Check the grassbox frequently for wear or
deterioration.
4. Replace worn or damaged parts for safety.
5. Only use the replacement blade, and blade bolt
specified for this product.
6. Be careful during adjustment of the product to
prevent entrapment of the fingers between
moving blades and fixed parts of the machine.
7. Store in a cool dry place and out of reach of
children. Do not store outdoors.
8. Allow the product to cool for at least 30 minutes
before storing.
PAGE 3
Cables
CABLES - IMPORTANT
• Use only 1.00mm2 size cable up to 40 metres
length maximum.
Maximum rating :
1.00mm2 size cable, 10 amps 250 volts AC.
• YOUR PRODUCT IS SUPPLIED WITH AN
ELECTRIC MAINS CABLE FITTED WITH A FEMALE
CONNECTOR.
1. Flymo Mains Cables and Extension Cables are
available from your local Approved Service
Centre.
2. Do not wire an extension cable directly to your
product yourself. Please contact your local
Approved Service Centre for further information
on the connectors and kits available.
3. Only use extension cables specifically designed
for outdoor use.
CONNECTORS - IMPORTANT
• Flymo connectors are suitable for use with 2 core
cable only. Under no circumstances should these
connectors be used for earthed products.
• All Flymo connectors and cables are of
splashproof construction. They are not waterproof
and must not be left outside permanently nor
should they be submerged or immersed in water.
Do not let cable lay or trail through pools of water
or splashed with water from hose pipes.
MAINS PLUG REPLACEMENT - IMPORTANT
• If the plug supplied is cut off it should be
destroyed. There is an electric shock hazard if a
cut off plug is inserted into a 13 amp socket.
1. No earth required. Flymo products are double
insulated to EN60335 and under no
circumstances should an earth be connected to
any part of the product.
2. Ensure the mains voltage suits your product
3. IMPORTANT!
The wires in the mains lead are coloured in
accordance with the following code:
BLUE
NEUTRAL
BROWN LIVE
The wire which is coloured BLUE must be
connected to the Terminal which is marked with
the letter 'N' or coloured BLACK.
The wire which is coloured BROWN must be
connected to the Terminal which is marked with
the letter 'L' or coloured RED.
4. It is important that the outer sheath is clamped
correctly into the 3-pin plug.
5. If in doubt consult your local Service Repairer or
qualified electrician before the machine is used.
6. A 13 Amp fuse must be fitted to the Mains Plug.
7. The normal plug fuse and household fuse only
protect the electrical equipment and are not a
safeguard against electrocution.
IMPORTANT INFORMATION
A
When received from the
Manufacturer, the wheels are in a
raised position.
Do not switch on the product
before removing from the raised
position into position 5.
Roller Assembly
B1
B2
1. Turn product over.
2. Place both halves of the roller over the location pegs
as illustrated in fig.B1
3. Clip the roller together to secure it into position.(B2)
• Do not clip the roller together before placing over the
location pegs
PAGE 4
Assembly of Lower Handles to Lawnmower
C1
C2
C3
1. Pull the lower handle bolt until it locks into position as
illustrated in fig C1.
2. Place the Spring over the Bolt (C2)
D1
D2
D4
lower handle
cam lock
Insert the Lower Handle, Washer and Cam Lock on to
the Bolt (D3) and turn the Cam Lock 3 times
clockwise, as illustrated in fig D4.
4. Insert the Barrel Nut into the Cam Lock as illustrated
in fig D1.
5. Ensuring the lower handle is in the correct position (D2)
D3
3. Insert the Pivot Block on to the Bolt (C3)
Repeat for the other side.
pivot block
x3
washer
7. Ensuring the raised markings on the Pivot Block and
the deck are aligned (D5), fold down the Cam Lock
towards the Handle as illustrated in fig D6, and
continue to turn clockwise (D7) until tightened.
Repeat for the other side.
D5
D7
D6
8. The Cam Lock can be unlocked and locked as
illustrated in fig D8.
PAGE 5
D8
Assembly of Upper Handles to Lower Handles
E1
E2
E3
x3
1. Insert the Barrel Nut into the Cam Lock as illustrated
in fig E1.
2. Attach the Upper Handle to the Lower Handle with the
Round Headed Bolt, Washer and Cam Lock as
E4
illustrated in fig E2
3. Turn the Cam Lock 3 times clockwise, as illustrated in
fig E3.
E5
E6
5. The Cam Lock can be unlocked and locked as
illustrated in fig E6.
Repeat for the other side.
4. Fold down the Cam Lock towards the Handle as
illustrated in fig E4, and continue to turn clockwise
(E5) until tightened.
Grassbox Assembly
F1
F2
G1
Grassbox Handle Assembly
1. Locate the grassbox handle into the slots in the grassbox
upper and push until it clicks into position. (F1)
2. Looking at the underside of the lid (F2), ensure the
clips of the grassbox handle are securely located.
Grassbox Assembly
1. Locate the the grassbox halves together by aligning the
clips Ensure all clips are correctly located before clicking
into position. (G1)
2. Locate the grassbox lid onto the assemble grassbox by
aligning the clips. Ensure all clips are correctly located
before clicking into position (G2)
Fitting Fully Assembled Grassbox to Lawnmower.
1. Lift safety flap (H1)
2. Make sure the discharge chute is clean and free from
debris (H2)
3. Locate fully assembled grassbox onto 2 location points
(H3) at the rear of the deck as illustrated in pic. J
4. Locate safety flap onto the top of the grassbox. Ensure
the grassbox is securely located.
• IMPORTANT ! AFTER FITTING ENSURE NO GAP
REMAINS BETWEEN THE SAFETY FLAP AND THE
GRASSBOX.
• Removal is the reverse procedure.
• For larger areas of grass where grass collection is not
required you can use your lawnmower without the
grassbox. The design of the safety flap permits the cut
grass to be discharged downward behind the machine.
G2
H
1
3
2
J
PAGE 6
How to Mow
K
Your product can be used to cut grass using the following
methods:1. Grassbox Fitted:- grass is collected effectively and
compacted into the grassbox. (K)
2. Rear Discharge:- Effectively cuts long grass with no
need to empty the grassbox (L)
3. Mulch Plug Fitted:- grass cuttings are finely chopped
to return nutrients to your lawn (M). See ‘Mulching Plug’
on page 7.
L
How to Mow
1. Start mowing the edge of the lawn nearest to the power
point so the cable is laid out on the lawn you have
already cut.
2. Mow twice a week during the growing season, your
lawn will suffer if more than a third of its length is cut at
one time and this may also result in poor collection.
Do Not Overload Your Mower
Mowing long thick grass may cause the motor speed to
drop, you will hear a change in the motor sound. If the
motor speed drops you may overload your lawnmower
which may cause damage. When mowing in long thick
grass a first cut with the cutting height set higher will
help reduce the load. See Cutting Height Adjustment.
M
Grassbox Full Window
N
grassbox
empty
grassbox
full
•
As the grassbox fills up, grass will be visible through
the window (N).
•
When the window/grassbox is full it is time to empty
the grassbox.
Mulching Plug
P1
P2
Using as a mulcher
P3
P4
1. Your lawnmower is supplied with a mulching plug. (P1)
2. Stop your lawnmower as described in Starting and
Stopping.
3. Lift safety flap and insert the mulching plug into rear
discharge chute. (P2) ensuring it is securely fitted. (P3)
4. The mulching plug prevents grass from being collected
by blocking the collection chute on the underside of
the deck. (P4)
PAGE 7
Cutting Height Adjustment
Cutting Height Adjustment
• Height of cut is adjusted by raising or lowering the
wheels using the height adjustment lever (Q)
• There are five heights of cut on this product.
• NOTE
A medium height of cut is recommended for
most lawns.
The quality of your lawn will suffer and
collection will be poor if you cut too low.
Q
Starting and Stopping
To Start your Lawnmower
1. Connect female extension cable connector to the back
of the switchbox. (R)
2. Form loop in mains cable and push the loop through
the slot. (S)
3. To secure, position loop over the hook and pull the
cable back through the slot (T).
4. Connect plug to mains and switch on.
5. Tilt the handle downwards to slightly raise the front of
the lawnmower and to reduce the risk of lawn damage
whilst starting.
The switchbox is provided with a lock-off button (U1) to
prevent accidental starting.
6. Press and hold the lock-off button (U) on the
switchbox, then squeeze one of the Start/Stop levers
towards the upper handle (V).
6. Continue to squeeze the start/stop lever towards the
upper handle and release the lock-off button (W).
7. Lower the lawnmower to its proper operating position
and commence mowing.
• NOTE - There are two start/stop levers fitted. Either
one can be used for starting the lawnmower.
• IMPORTANT - Do not use the start/stop levers
intermittently
To Stop your Lawnmower
1. Release the pressure on the Start/Stop lever.
R
S
T
U
1
V
W
Removing and Fitting the Blade
Switch off, wait until the blade has stopped rotating and
disconnect from the mains electricity supply BEFORE
attempting to remove or refit the blade. Always handle
the blade with care - sharp edges could cause injury.
USE GLOVES.
Removing the Blade
1. To remove the blade bolt, hold the blade firmly with a
gloved hand and with a spanner, loosen the blade bolt
by turning it anti-clockwise (X).
2. Remove the blade bolt, blade and adaptor. (X)
3. Inspect for damage and clean as necessary.
Renew your metal blade after 50 hours mowing or 2
years whichever is the sooner - regardless of condition.
If the blade is cracked or damaged replace it with a new
one.
Fitting the Blade
1. Attach the adaptor to the shaft.
2. Fit the blade to the adaptor ensuring that once it is
fitted you are able to read the text on the blade ‘This
side to grass’
3. Re-assemble blade bolt through the blade and the
adaptor.
4. Hold the blade firmly with a gloved hand and tighten
the blade bolt firmly with a spanner. Do not over
tighten.
X
blade bolt
blade
adaptor
PAGE 8
Caring for your Lawnmower
Z1
Z2
Cleaning
• USE GLOVES
• IMPORTANT:- It is very important that you keep your
lawnmower clean. Grass clippings left in any of the air
intakes or under the deck could become a potential
fire hazard.
1. Remove grass from under the deck with brush. (Z1)
Z3
Z4
2. Using a soft brush - remove grass clippings from all air
intakes (Z2), the discharge chute (Z3) and the grass
box (Z4).
3. Using a soft brush, remove grass clippings from the
vision window (Z5).
Z5
4. Wipe over the surface of your lawnmower with a dry
cloth (Z6).
Z6
Z7
• IMPORTANT:- Never use water for cleaning your
lawnmower. Do not clean with chemicals, including
petrol, or solvents - some can destroy critical plastic
parts.
Z8
Z9
Cleaning Easi-Reel cable winder (XC Models only)
1. Lift grassbox lid, squeeze together the two catches
(Z7) and remove the cable spool.
2. Clean the cable spool (Z8) and the area it was located
with a soft brush (Z9)
3. Replace the cable spool, ensuring it clicks into place.
Storing your Lawnmower:
• Loosen the wing knobs to enable the handles to be
folded over the product (Z10).
• Store in a dry place where your lawnmower is
protected from damage
At the End of the Mowing Season
1. Replace blade, bolts, nuts or screws, if necessary.
2. Clean your lawnmower thoroughly.
3. Make sure that the electric cable is stored correctly to
prevent damage.
Z10
Replacement Parts
Blade
340XC
360/360XC
420/420XC
Reference no.:
Reference no.:
FLY062
FLY059
Part no.:
Part no.:
Part no.:
PAGE 9
521947390
505492090
5107842-01
Easi-Reel Cable Winder (XC models only)
Y1
Y2
Storing your cable in the Easi-Reel cable winder
1. Insert the female connector into the centre of the
cable winder (Y1)
2. Place the cable under the cable guide (Y2)
3. Turn the cable winder (Y3) until all of the cable is
wound in.(Y4)
Y3
Y4
Unwinding the cable before re-use
1. Pull the cable by the plug and unwind the cable fully.
• Ensure that the cable is released from the cable guide
(Y2) before using your machine.
• Ensure cable is not entangled with any other cables
and that it is not trapped in any parts of the product.
Fault Finding Hints
Fails to Operate
1. Is the correct Starting procedure being followed? See
‘To Start your Lawnmower’
2. Is the Power Turned On?
3. Check the fuse in the plug, if blown replace.
4. Fuse continues to blow?
Immediately disconnect from the mains electricity supply
and consult your local approved Service Centre.
Poor Grass Collection
1. Disconnect from the mains electricity supply.
2. Clean the outside of the air intakes, the discharge
chute and the underside of the deck.
3. Raise to a higher height of cut. See Cutting Height Adjustment.
4. If poor collection persists.
Immediately disconnect from the mains electricity supply
and consult your local approved Service Centre.
Excessive Vibration
1. Disconnect from the mains electricity supply.
2. Check that the blade is fitted correctly?
3. If the blade is damaged or worn, replace it with a new one.
4. If vibration persists?
Immediately disconnect from the mains electricity supply
and consult your local approved Service Centre.
Lawnmower becomes heavy to push
1. Disconnect from the mains electricity supply.
2. In long grass or uneven ground, the height of cut
should be raised to a higher position. See Cutting
Height Adjustment.
3. Check that the wheels and rollers can rotate freely.
4. If problem persists?
Immediately disconnect from the mains electricity supply
and consult your local approved Service Centre.
Service Recommendations
1. We strongly recommend that your product is serviced
at least every twelve months, more often in a
professional application.
2. Always use genuine Spare Parts.
3. Prepacked spares are available from most Husqvarna
Outdoor Products stockists.
4. Your product is uniquely identified by a silver and
black product rating label
5. If you have a problem with your machine contact your local
Approved Service Centre ensuring you have full details of
your product as described on the product rating label.
6. Should it be necessary for work to be carried out by
your Service Centre, it is important to take your
complete machine including cable and any extension
cables used.
A network of specialist dealers can be found in your local
Yellow Pages. To obtain service on your product simply
telephone or visit your local Service Centre. Should you
require service under the terms of our guarantee the Service
Centre will require proof of purchase.
All of the centres listed stock genuine Spare Parts.
NOTE: Our Service Repairers act on their own behalf
and are not empowered to commit or legally bind
Husqvarna UK Ltd. in any manner whatsoever.
Environmental Information
Husqvarna UK Ltd. products are manufactured under an
Environmental Management System (ISO 14001) using,
where practical, components manufactured in the most
environmentally responsible manner, according to
company procedures, and with the potential for recycling
at the end of the products’ life.
• Packaging is recyclable and plastic components have
been labelled (where practical) for categorised recycling.
• Awareness of the environment must be considered
when disposing of ‘end-of-life’ product.
• If necessary, contact your local authority for disposal
information.
The symbol
on the product or on its packaging indicates
that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment
and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more detailed
information about recycling of this product, please contact your
local council office, your household waste disposal service or
the shop where you purchased the product.
PAGE 10
Guarantee & Guarantee Policy
If any part is found to be defective due to faulty manufacture
within the guarantee period, Husqvarna UK Ltd., through its
Authorised Service Repairers will effect the repair or replacement
to the customer free of charge providing:
(a) The fault is reported directly to the Authorised Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty
adjustment by the user.
(d) The failure has not occurred through fair wear and tear.
(e) The machine has not been serviced or repaired,
taken apart or tampered with by any person not
authorised by Husqvarna UK Ltd.
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used commercially.
*
This guarantee is additional to, and in no way
diminishes the customers statutory rights.
Failures due to the following are not covered, therefore it
is important that you read the instructions contained in
this Operator's Manual and understand how to operate
and maintain your machine:
Failures not covered by guarantee
* Replacing worn or damaged blades.
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in
accordance with the instructions and
recommendations contained in this Operator's
Manual.
* Machines used for hire are not covered by this
guarantee.
* The following items listed are considered as wearing
parts and their life is dependent on regular
maintenance and are, therefore not normally subject
to a valid warranty claim: Blades, Electric Mains cable
* Caution!
Husqvarna UK Ltd. does not accept liability under the
warranty for defects caused in whole or part, directly
or indirectly by the fitting of replacement parts or
additional parts that are not either manufactured or
approved by Husqvarna UK Ltd., or by the machine
having been modified in any way.
EC Declaration of Conformity
Husqvarna AB, 561 82, Huskvarna, Sweden
Declare under our sole responsibility that the product(s);
Category............................Electric Rotary Lawnmower
Type(s) ............................MM340XC, MM360, MM360XC, MM420, MM420XC
Identification of Series.......See Product Rating Label
Year of Construction..........See Product Rating Label
Conforms to the essential requirements & provisions of the following EC Directives:
98/37/EC (until 28.12.09), 2006/42/EC (from 29.12.09), 2004/108/EC, 2000/14/EC
based on the following EU harmonized standards applied:
EN60335-1, EN60335-2-77, EN836, EN50366, EN55014-1, EN61000-3-2, EN61000-3-3
The maximum A weighted sound pressure level LpA at the operator’s position, recorded on a sample of the above
product(s) corresponds to the Level given in the table.
The maximum hand / arm vibration weighted value measured according to EN ISO 5349 on a sample of the above
product(s) corresponds to the Value ah given in the table.
2000/14/EC: The Measured Sound Power LWA & Guaranteed Sound Power LWA values are according to the tabulated
figures.
Conformity Assessment Procedure.................. Annex VI
Notified Body.................................................... Intertek, Cleeve Road
Leatherhead, Surrey
KT22 7SB, England
Newton Aycliffe 25/11/2009
M.Bowden
Research & Development Director
Husqvarna UK Ltd.
Keeper of technical documentation
Type
Width of Cut (cm)
Speed of Rotation of Cutting Device (rpm)
Power (kW)
Measured Sound Power LWA (dB(A))
Guaranteed Sound Power LWA (dB(A))
Level (dB(A))
Value ah (m/s2)
Uncertainty K of ah (m/s2)
Weight (Kg)
MM340XC
34
3,850
1.5
93
MM360
36
3,850
1.5
93
MM360XC
36
3,850
1.5
93
96
80.4
1.56
1.5
12.8
96
80.4
1.56
1.5
12.4
96
80.4
1.56
1.5
12.8
MM420
42
3,600
1.7
95
96
84.9
1.53
1.5
13.1
MM420XC
42
3,600
1.7
95
96
84.9
1.53
1.5
14.7
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.
Copyright © 2008 Flymo S.A. All rights reserved. Flymo® and other product and feature names are registered or unregistered
trademarks of Flymo S.A.
5100693-02
Husqvarna AB
561 82
Huskvarna
Sweden
Download PDF

advertising