Specifications | Fluke 52 Series Thermostat User Manual

®
51 & 52 Series II
Thermometer
Users Manual
English
September 1999 Rev.1, 6/01
© 1999-2001 Fluke Corporation, All rights reserved. Printed in USA
All product names are trademarks of their respective companies.
Limited Warranty & Limitation of Liability
This Fluke product will be free from defects in material and workmanship for 3 years from the date of purchase. This warranty does not cover fuses, disposable batteries or damage from accident, neglect, misuse or abnormal conditions of operation or handling. Resellers are not authorized to extend any other warranty on Fluke’s behalf. To obtain service during the
warranty period, send your defective tester to the nearest Fluke Authorized Service Center with a description of the problem.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR
PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some states or countries
do not allow the exclusion or limitation of an implied warranty or of incidental or consequential damages, this limitation of
liability may not apply to you.
Fluke Corporation
Fluke Europe B.V.
P.O. Box 9090
P.O. Box 1186
Everett WA
5602 B.D. Eindhoven
98206-9090
The Netherlands
To register your product, visit www.fluke-warranty.com
10/96
Table of Contents
Title
Introduction ....................................................................................................................
Contacting Fluke .......................................................................................................
Getting Started...............................................................................................................
Components..............................................................................................................
Display Elements ......................................................................................................
Buttons......................................................................................................................
Using the Thermometer .................................................................................................
Changing Setup Options................................................................................................
Entering or Exiting Setup ..........................................................................................
Setup Options ...........................................................................................................
Changing a Setup Option..........................................................................................
Measuring Temperatures...............................................................................................
Connecting a Thermocouple .....................................................................................
Displaying Temperatures ..........................................................................................
Holding the Displayed Readings ...............................................................................
Viewing the MIN, MAX, and AVG Readings..............................................................
Using the Offset to Adjust for Probe Errors....................................................................
i
Page
1
1
4
5
6
7
9
9
9
9
10
11
11
11
12
12
12
51 & 52 Series II
Users Manual
Maintenance...................................................................................................................
Replacing the Batteries .............................................................................................
Cleaning the Case and Holster..................................................................................
Calibration .................................................................................................................
Specifications .................................................................................................................
Environmental............................................................................................................
General......................................................................................................................
80 PK-1 Thermocouple (supplied with thermometer) ................................................
Electrical....................................................................................................................
Replacement Parts and Accessories..............................................................................
ii
13
13
13
13
13
13
14
14
14
15
51 & 52 Series II
Introduction
Contacting Fluke
The Fluke Model 51 and Model 52 Thermometers (“the
thermometer”) are microprocessor-based, digital
thermometers designed to use external J-, K-, T-, and Etype thermocouples (temperature probes) as temperature
sensors.
To order accessories, receive assistance, or locate the
nearest Fluke distributor or Service Center, call:
Use the thermometer only as specified in this manual.
Otherwise, the protection provided by the meter may be
impaired.
Refer to safety information in Table 1 and meter symbols
in Table 2.
1-888-99-FLUKE (1-888-993-5853) in USA
1-800-36-FLUKE (1-800-363-5853) in Canada
+31-402-678-200 in Europe
+81-3-3434-0181 in Japan
+65-738-5655 in Singapore
+1-425-446-5500 from other countries
Address correspondence to:
Fluke Corporation
P.O. Box 9090
Everett, WA 98206-9090
USA
Fluke Europe B.V.
P.O. Box 1186
5602 BD Eindhoven
The Netherlands
Visit us on the World Wide Web at: www.fluke.com
To register your product, visit www.fluke-warranty.com
1
51 & 52 Series II
Users Manual
Table 1. Safety Information
WWarning
A Warning identifies conditions and actions that pose hazards to the user. To avoid electrical shock or
personal injury, follow these guidelines:
• Before using the thermometer inspect the case. Do not use the thermometer if it appears damaged. Look
for cracks or missing plastic. Pay particular attention to the insulation around the connectors.
• Disconnect the thermocouple(s) from the thermometer before opening the case.
• Replace the batteries as soon as the battery indicator (B) appears. The possibility of false readings can
lead to personal injury.
• Do not use the thermometer if it operates abnormally. Protection may be impaired. When in doubt, have the
thermometer serviced.
• Do not operate the thermometer around explosive gas, vapor, or dust.
• Do not apply more than the rated voltage, as marked on the thermometer, between the thermocouple(s), or
between any thermocouple and earth ground.
2
51 & 52 Series II
Introduction
Table 1. Safety Information (cont.)
WWarning (cont.)
• Model 52: Measurement errors may occur if voltages on the measurement surfaces result in potentials
greater than 1 V between the two thermocouples. When potential differences are anticipated between the
thermocouples, use electrically insulated thermocouples.
• When servicing the thermometer, use only specified replacement parts.
• Do not use the thermometer with any part of the case or cover removed.
Caution
A Caution identifies conditions and actions that may damage the meter or the equipment under test.
• Use the proper thermocouples, function, and range for your thermometer.
• Do not attempt to recharge the batteries.
• To prevent explosion, do not throw batteries into a fire.
• Follow local laws or regulations when disposing of batteries.
• Match the + and − polarities of the battery with the battery case.
3
51 & 52 Series II
Users Manual
Table 2. International Symbols
W
Refer to the manual for information about this
feature.
M
Battery.
P
Complies with European Union directives.
Complies with relevant Canadian Standards
Association directives.
Getting Started
•
Figure 1 and Table 3 describe the components.
Everything in this Users Manual applies both to Models
51 and 52 unless otherwise indicated.
•
Figure 2 and Table 4 describe the display.
•
Table 5 describes the functions of the buttons.
To become familiar with the thermometer, study the
following:
4
Then read the following sections.
51 & 52 Series II
Getting Started
Components
Table 3. Components
xx
3
2
5
1
4
A
Thermocouple T1 input
B
Model 52: Thermocouple T2 input
C
Holster
D
Display
E
Buttons
F
Battery door
G
Batteries
6
7
aas01f.eps
Figure 1. Components
5
51 & 52 Series II
Users Manual
Display Elements
Table 4. Display Elements
xx
2
3
4
1
5
6
7
10
The thermocouple measurement includes an
offset. See "Changing Setup Options."
B
The displayed readings do not change.
C
A shift function is in progress.
D
Setup is in progress.
E
Low battery. Replace the batteries.
F
Primary Display.
8
9
aas02f.eps
Figure 2. Display Elements
6
A
Model 51: T1 reading.
Model 52: T1, T2, or T1-T2 reading.
G
The temperature unit.
H
Secondary Display: MAX, MIN, AVG, or offset.
Model 52: T1or T2 reading.
I
The thermocouple type.
J
Time Display: The elapsed time.
51 & 52 Series II
Getting Started
Buttons
Table 5. Buttons
A
Press A to turn the thermometer on or off.
G
Press G, M (CANCEL) to stop displaying the minimum, maximum, and average readings in the
secondary display.
(Shift
function)
Q
Press Q to turn the backlight on and off. The backlight turns off after 2 minutes without any button
presses. If the battery is low, the backlight is disabled.
M
Press M to step through the maximum, minimum, and average readings. When viewing logged
readings, shows the maximum, minimum, and average of the logged readings.
Press G, M (CANCEL) to turn off this display.
C
Press C to switch between Celsius ( C), Fahrenheit ( F), and Kelvin (K).
h
Press h to freeze or unfreeze the displayed readings.
o
o
Press h when turning on the thermometer to test the display. All display elements appear.
T
Model 52: Press T to toggle showing the T1, T2, and T1-T2 (differential temperature measurement) in the
primary or secondary display.
7
51 & 52 Series II
Users Manual
Table 5. Buttons (cont.)
D
Press D to start or exit Setup. (See "Changing Setup Options.")
K
Press K to scroll to the Setup option you want to change.
Press K to increase the displayed setting.
N
Press N to scroll to the Setup option you want to change.
Press N to decrease the displayed setting.
E
Press E to enter a Setup option.
Press E again to store the displayed setting in memory.
8
51 & 52 Series II
Using the Thermometer
Using the Thermometer
Entering or Exiting Setup
1.
Plug the thermocouple(s) into the input connector(s).
When the thermometer is in Setup mode, the display
shows s.
2.
Press A to turn on the thermometer.
•
After 1 second the thermometer displays the first reading.
If no thermocouple is plugged into the selected input or the
thermocouple is "open," the display shows "- - - -"
Changing Setup Options
Use Setup to change the thermocouple type, offset, sleep
mode, and line frequency settings.
The thermometer stores the settings in its memory. Setup
settings reset only when the batteries are removed for
more than 2 minutes.
Press D to start or exit Setup.
Setup Options
Option
Menu
Item
Settings
Thermocouple
Type
TYPE
J, K, T, or E
Offset
O
T1 or T2 (Model 52)
Sleep Mode
SLP
on (sleep mode on)
or 0FF (sleep mode
off)
Line Frequency
Li ne
50 H (50 Hz)
or 60 H (60 Hz)
9
51 & 52 Series II
Users Manual
Changing a Setup Option
1.
Press K or N to scroll to the setup option you
want to change.
2.
Press E to indicate that you want to change this
setting.
3.
Press K or N until the setting you want to use
appears on the display.
4.
Press E to store the new setting in memory.
Notes
Setup is disabled in MIN MAX mode.
Offset:
The primary display shows the temperature plus
the offset and the secondary display shows the
offset. Remember to reset the offset to 0.0 when
it is no longer needed. The offset automatically
resets to 0.0 when you change the thermocouple
type. Model 52: You can store individual offsets
for T1 and T2.
10
Sleep mode:
The thermometer enters sleep mode if no button
press occurs for 20 minutes. Pressing any button
wakes the thermometer and returns it to its
previous state. Sleep mode becomes enabled
each time you turn on the thermometer and is
automatically disabled in MIN MAX mode.
Line frequency:
For optimum rejection of line noise, the
thermometer must be set for the local line
frequency.
51 & 52 Series II
Measuring Temperatures
Notes
Measuring Temperatures
Connecting a Thermocouple
The display shows "- - - -" when a thermocouple
is not connected.
To change the thermocouple type, see “Changing Setup
Options.” The North American ANSI Color Code is:
The display shows 0L (overload) when the
temperature being measured is outside the
thermocouple’s valid range.
Type
J
K
E
T
N
Color
Black
Yellow
Purple
Blue
Orange
1.
Plug a thermocouple into the input connector(s).
(Make sure that the polarity is correct.)
2.
Set the thermometer for the correct thermocouple
type.
Model 52: If only thermocouple T2 is connected,
the T2 reading appears in the primary display.
Displaying Temperatures
1.
Press C to select the correct temperature scale.
2.
Hold or attach the thermocouple(s) to the
measurement location.
The temperature reading appears in the primary
display.
3.
T
Model 52: Press
to toggle between showing the
T1, T2, and T1-T2 readings in the primary or
secondary display.
11
51 & 52 Series II
Users Manual
Holding the Displayed Readings
1.
Press h to freeze the readings on the display.
The display shows H.
2.
3.
Model 52: Press T to toggle showing the T1, T2, or
T1-T2 readings in the primary or secondary display.
Press h again to turn off the HOLD function.
Viewing the MIN, MAX, and AVG Readings
1.
2.
12
Using the Offset to Adjust for Probe
Errors
Use the offset option in Setup to adjust the thermometer’s
readings to compensate for the errors of a specific
thermocouple.
The allowable adjustment range is ± 5.0 C or K, and
o
± 9.0 F.
o
1.
Plug the thermocouple into the input connector.
Press M to step through the maximum (MAX),
minimum (MIN), or the average (AVG) readings.
2.
The elapsed time since entering MIN MAX mode, or
the time at which the minimum or maximum occurred,
appears on the display.
Place the thermocouple in a known, stable
temperature environment (such as an ice bath or a
dry well calibrator).
3.
Allow the readings to stabilize.
4.
In Setup change the offset until the primary display
reading matches the calibration temperature. (See
"Changing Setup Options.")
Press G, M (CANCEL) to exit MIN MAX mode.
51 & 52 Series II
Maintenance
Maintenance
Calibration
Replacing the Batteries
To ensure that the thermometer performs to its accuracy
specifications, Fluke recommends that you calibrate the
thermometer annually, starting one year after purchase.
Refer to the safety information in Table 1 before replacing
the batteries.
1.
Turn off the thermometer if necessary.
2.
Loosen the screw and remove the battery door.
3.
Replace the three AA batteries.
4.
Replace the battery door and tighten the screw.
Cleaning the Case and Holster
Use soap and water or a mild commercial cleaner.
Wipe with a damp sponge or soft rag.
To calibrate the thermometer, contact Fluke for the
Service Center nearest you or follow the calibration
procedure in the service manual listed in "Replacement
Parts and Accessories."
Specifications
Environmental
Operating
−10 C to 50 C
o
o
Temperature
(14 F to 122 F)
o
o
Storage
−40 C to +60 C
o
o
Temperature
(−40 F to +140 F)
o
Humidity
o
o
o
Non condensing <10 C (<50 F)
o
o
o
o
95% RH: 10 C to 30 C (50 F to 86 F)
o
o
o
o
75% RH: 30 C to 40 C (86 F to 104 F)
o
o
o
o
45% RH: 40 C to 50 C (104 F to 122 F)
13
51 & 52 Series II
Users Manual
General
Weight
280 g (10 oz)
Dimensions
(without
holster)
2.8 cm × 7.8 cm × 16.2 cm
(1.1 in × 3 in × 6.4 in)
Battery
3 AA batteries
Certification
P, ) s
Safety
CSA C22.2 No. 1010.1 1992
EN 61010 Amendments 1, 2
CAT I
OVERVOLTAGE (Installation)
CATEGORY I, Pollution Degree 2
per IEC1010-1*
* Refers to the level of Impulse Withstand Voltage protection
provided. Equipment of OVERVOLTAGE CATEGORY I is
equipment for connection to circuits in which measures are
taken to limit the transient over voltages to an appropriate low
level. Example include protect electronic circuits.
14
80 PK-1 Thermocouple (supplied with
thermometer)
Type
Type K, Chromel Alumel, bead style
Temperature
Range
−40 C to +260 C
o
o
(−40 F to +500 F)
Accuracy
± 1.1 C (± 2.0 F)
o
o
o
o
Electrical
Measurement
Range
J-type: −210 C to +1200 C
o
o
(−346 F to + 2192 F)
o
o
K-type: −200 C to +1372 C
o
o
(−328 F to +2501 F)
o
o
T-type: −250 C to +400 C
o
o
(−418 F to +752 F)
o
o
E-type: −150 C to +1000 C
o
o
(−238 F to +1832 F)
o
Display
Resolution
o
0.1 C / F / K < 1000
o
o
o
1.0 C / F / K ≥ 1000
o
o
o
51 & 52 Series II
Replacement Parts and Accessories
Electrical (cont.)
Measurement
Accuracy, T1,
T2, or T1-T2
(Model 52)
Temperature
Coefficient
Electromagnetic
Compatibility
Maximum
Differential
Common Mode
Voltage
Temperature
Scale
Replacement Parts and Accessories
J-, K-, T-, andoE-type:o±[0.05 % of
reading + 0.3
C (0.5o F)]
o
[below −100 C (−148 F): add 0.15 %
of reading for J-, K-, E-, and N-type;
and 0.45 % of reading for T-type]
0.01 %o of reading
+ 0.03 C per C
o
(0.05 F per F)
outsideo the o
o
specified
+18 C to 28 C (+64 F
o
to +82 F) range
o
o
[below −100 C (−148 F): add
0.04 % of reading for J-, K-, E-, and
N-type; and 0.08 % of reading for
T-type]
o
o
Susceptibility: ±2 C (±3.6 F) for 80
MHz to 200 MHz in 1.5 V/m field, for
200 MHz to 1000 MHz in 3 V/m field.
Emmisions: Commercial Limits per
EN50081-1
1 V (Maximum voltage difference
between T1 and T2)
o
o
Accessory
Part Number
Holster and Flex Stand Assembly
1272438
AA NEDA 15A IEC LR6 batteries
376756
80PK-1 K-Type Bead Thermocouple
773135
CD-ROM
1276106
Service Manual
1276123
ITS-90
Applicable
NIST-175
Standards
Accuracy is specified
for ambient
temperatures
o
o
o
o
between 18 C (64 F) and 28 C (82 F) for a period of
1 year. The above specifications do not include
thermocouple error.
15
51 & 52 Series II
Users Manual
16
Download PDF

advertising