Flymo EM032 Lawn Mower User Manual

VENTURER 32 (VTR32)
VISIMO (VM032)
ROLLERMO (RM032)
EASIMO (EM032)
®
Original Instructions
ROLLERMO
VENTURER 32
EASIMO
VISIMO
RM
INFO
N
AT I O
T
RTA N
I M P O efore use
rence
b
e refe
r
d
u
a
t
e
u
f
R
in for
& reta
Carton Contents
switchbox
start/stop lever
lock off
button
cable clip x 2
grassbox
handle
washer x 4
bolt x 2
wingknob x 4
upper handle
grassbox
upper
grassbox
lower
Easimo
only
grassbox
tongue
electric
cable with
moulded
on plug
safety flap
lower handle x 2
motor cover
deck
instruction
manual
IMPORTANT !
Please check the contents of the carton are correct BEFORE assembling your new Flymo product. The Loose Parts
Pack is packaged underneath the deck of the product.
IF ANY PARTS ARE MISSING CONTACT:Husqvarna UK Ltd. Customer Service Department direct
Telephone : 0844 844 4558
Fax : 01325 302530
Safety
If not used properly this product can be dangerous! This product can cause serious injury to the operator
and others, the warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this product. The operator is responsible for following the warning and safety instructions in
this manual and on the product. Never use the mower unless the grassbox or guards provided by the
manufacturer are in the correct position.
Explanation of Symbols on your product
Warning
Read the user instructions carefully to make
sure you understand all the controls and
what they do.
Beware of sharp blades - remove plug from
mains before maintenance or if cable is
damaged.
Blades continue to rotate after the machine
is switched off.
Always keep the product on the ground when
operating. Tilting or lifting the product may
cause stones to be thrown out.
Keep bystanders away. Do not operate
whilst people especially children or pets are
in the area.
General
1. This product is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or in-
Keep the cable supply away from the cutting
means.
struction concerning the use of the product by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the
product. Local regulations may restrict the age of the
operator.
Never allow children or people unfamiliar with the instructions to use the machine.
Stop using the machine while people, especially children,
or pets are nearby.
4. Only use the product in the manner and for the functions described in these instructions.
5. Never operate the product when you are tired, ill or under
the influence of alcohol, drugs or medicine.
6. The operator or user is responsible for accidents or hazards occurring to other people or their property.
Electrical
1. The British Standards Institute recommend the use of a
Residual Current Circuit Device (R.C.D.) with a tripping
current of not more than 30mA. Even with a R.C.D. installed 100% safety cannot be guaranteed and safe
working practice must be followed at all times. Check
your R.C.D. every time you use it.
2. Before use, examine cable for damage, replace it if
there are signs of damage or ageing.
3. Do not use the product if the electric cables are damaged or worn
4. Immediately disconnect from the mains electricity supply
if the cable is cut, or the insulation is damaged. Do not
touch the electric cable until the electrical supply has
been disconnected. Do not repair a cut or damaged
cable. Replace it with a new one.
5. Your extension cable must be uncoiled, coiled cables can
overheat and reduce the efficiency of your product.
6. Keep cable away from product, always work away from
the power point mowing up and down, never in circles.
7. Do not pull cable around sharp objects.
8. Always switch off at the mains before disconnecting any
plug, cable connector or extension cable.
9. Switch off, remove plug from mains and examine
electric supply cable for damage or ageing before
winding cable for storage. Do not repair a damaged
cable, replace it with a new one. Use only Flymo replacement cable.
10. Always wind cable carefully, avoiding kinking.
11. Never carry the product by the cable.
12. Never pull on the cable to disconnect any of the plugs.
13. Use only on AC mains supply voltage shown on the
product rating label.
14. Flymo Products are double insulated to EN60335.
Under no circumstance should an earth be connected
to any part of the product.
Preparation
1. While using your product always wear substantial
footwear and long trousers.
2. Make sure the lawn is clear of sticks, stones, bones, wire
and debris; they could be thrown by the blade.
3. Before using the machine and after any impact, check for
signs of wear or damage and repair as necessary.
Replace worn or damaged blades together with their
fixings in sets to preserve balance.
Use
1. Use the product only in daylight or good artificial light.
2. Avoid operating your product in wet grass, where feasible.
3. Take care in wet grass, you may lose your footing.
4. On slopes, be extra careful of your footing and wear
non-slip footwear.
5. Mow across the face of slopes, never up and down.
6. Exercise extreme caution when changing direction on
slopes. Walk never run.
7. Mowing on banks and slopes can be dangerous. Do
not mow on banks or steep slopes.
8. Do not walk backwards when mowing, you could trip.
9. Never cut grass by pulling the product towards you.
10. Switch off before pushing the product over surfaces
other than grass.
11. Never operate the product with damaged guards or
without guards in place.
12. Keep hands and feet away from the cutting means at all
times and especially when switching on the motor.
13. Do not tilt product when the motor is running, except
when starting and stopping. In this case, do not tilt
more than absolutely necessary and lift only the part
which is away from the operator. Always ensure that
both hands are in the operating position before returning the appliance to the ground.
14. Do not put hands near the grass discharge chute.
15. Never pick up or carry a product when it is operating
or still connected to the mains supply.
16. Remove the plug from the mains :
before leaving the product unattended for any period;
before clearing a blockage;
before checking, cleaning or working on the appliance;
if you hit an object. Do not use your product until you
are sure that the entire product is in a safe operating
condition.;
if the product starts to vibrate abnormally. Check immediately. Excessive vibration can cause injury.
Maintenance and storage
1. Keep all nuts, bolts and screws tight to be sure the
lawnmower is in safe working condition.
2. Check the grassbox frequently for wear or deterioration.
3. Replace worn or damaged parts for safety.
4. Only use the replacement blade, and blade bolt specified for this product.
5. Be careful during adjustment of the product to prevent
entrapment of the fingers between moving blades and
fixed parts of the machine.
6. Store in a cool dry place and out of reach of children.
Do not store outdoors.
CABLES - IMPORTANT
• Use only 1.00mm2 size cable up to 40 metres length
maximum.
Maximum rating :
1.00mm2 size cable, 10 amps 250 volts AC.
• YOUR PRODUCT IS SUPPLIED WITH CABLE
WIRED DIRECTLY INTO THE PRODUCT.
1. Flymo Mains Cables and Extension Cables are available
from your local Approved Service Centre.
2. Do not wire an extension cable directly to your product
yourself. Please contact your local Approved Service
Centre for further information on the connectors and
kits available.
3. Only use extension cables specifically designed for
outdoor use.
CONNECTORS - IMPORTANT
• Flymo connectors are suitable for use with 2 core
cable only. Under no circumstances should these connectors be used for earthed products.
• All Flymo connectors and cables are of splashproof
construction. They are not waterproof and must not be
left outside permanently nor should they be submerged
or immersed in water. Do not let cable lay or trail
through pools of water or splashed with water from
hose pipes.
MAINS PLUG REPLACEMENT - IMPORTANT
• If the plug supplied is cut off it should be destroyed.
There is an electric shock hazard if a cut off plug is inserted into a 13 amp socket.
1. No earth required. Flymo products are double insulated to
EN60335 and under no circumstances should an earth be
connected to any part of the product.
2. Ensure the mains voltage suits your product
3. IMPORTANT!
The wires in the mains lead are coloured in accordance with the following code:
BLUE
NEUTRAL
BROWN LIVE
The wire which is coloured BLUE must be connected
to the Terminal which is marked with the letter 'N' or
coloured BLACK.
The wire which is coloured BROWN must be connected to the Terminal which is marked with the letter
'L' or coloured RED.
4. It is important that the outer sheath is clamped correctly into the 3-pin plug.
5. If in doubt consult your local Service Repairer or qualified electrician before the machine is used.
6. A 13 Amp fuse must be fitted to the Mains Plug.
7. The normal plug fuse and household fuse only protect
the electrical equipment and are not a safeguard
against electrocution.
2.
3.
4.
If your product is hard wired i.e. non-detachable
mains electric cable, a conversion kit and extension cable is available from all Approved Service
Centres which can be found in your local Yellow
Pages.
Assembly Instructions
A
3
2
1
B
1
2
C
1
3
4
5
2
D
E
• The Loose Parts Pack is packaged underneath the deck.
Assembly of Lower Handles to Deck
1. Place the bolt (A2) through the hole in the lower handle
(A1) until the lower handle fits into the recess (A3)
2. Place the washer (B1) and the wing knob (B2) on to
the bolt and tighten the wing knob.
3. Repeat on the other side.
Assembly of Upper Handles to Lower Handles.
1. Ensure the upper handle is located correctly with the
lock-off button on the switchbox uppermost.
2. Ensure the upper handle (C1) and the lower handle
(C2) are aligned correctly.
4. Fit the bolts (C3), washers (C4) and wing knobs (C5).
Tighten the wing knob.
5. Fit the cable to the handles with the clips provided.
Make sure the cable is not trapped between the upper
and lower handles.
Grassbox Assembly
1. Slide the grassbox tongue into the slots in the grassbox
lower until it clicks securely into position (D)
2. Push the grassbox handle into the slots in the grassbox
upper until it clicks securely into position. (E)
3. Starting at the rear of the grassbox, locate the grassbox upper into the grassbox lower by aligning the
clips (F1). Ensure all clips are correctly located.(F2)
before clicking into position.
4. Clip the two halves together, ensuring all clips are securely connected.
F1
F2
Grassbox
G
1
Fitting Fully Assembled Grassbox to Lawnmower.
1.
2.
3
3.
2
4.
H
J
•
IMPORTANT !
AFTER FITTING ENSURE NO GAP REMAINS BETWEEN THE SAFETY FLAP AND THE GRASSBOX.
•
•
Removal is the reverse procedure.
For larger areas of grass where grass collection is
not required you can use your lawnmower without
the grassbox. Ensure the Safety Flap is fully
closed. The design of the safety flap permits the cut
grass to be discharged downward behind the machine.
Visimo Only
grassbox
empty
grassbox
full
Lift safety flap (G1)
Make sure the discharge chute is clean and free
from debris (G2)
Locate fully assembled grassbox onto 2 location
points (G3) at the rear of the deck as illustrated in
pic. H
Locate safety flap onto the top of the grassbox. Ensure the grassbox is securely located.
Grassbox Full Window (Visimo Only)
•
As the grassbox fills up, grass will be visible through
the window (J).
•
When the window/grassbox is full it is time to empty
the grassbox.
Cutting Height Adjustment
K
L
2cm
4cm
6cm
Cutting Height Adjustment (K) & (L)
• Height of cut is adjusted by raising or lowering the
Front and Rear Wheels.
• There are five heights of cut on this product.
• NOTE
A medium height of cut is recommended for most
lawns.
The quality of your lawn will suffer and collection will
be poor if you cut too low.
HEIGHT OF CUT
Low
Low to Medium
Medium
Medium to High
High
WHEELS POSITION
Front position 2cm
Rear position 2cm
Front position 2cm
Rear position 4cm
Front position 4cm
Rear position 4cm
Front position 4cm
Rear position 6cm
Front position 6cm
Rear position 6cm
Starting and Stopping
M
N
P
Q
1
R
To Start your Lawnmower
1. Form loop in mains cable and push the loop through
the slot. (M)
2. To secure, position loop over the hook and pull the
cable back through the slot (N).
3. Connect plug to mains and switch on.
4. Tilt the handle downwards to slightly raise the front of
the lawnmower and to reduce the risk of lawn damage
whilst starting.
The switchbox is provided with a lock-off button (P1)
to prevent accidental starting.
5. Press and hold the lock-off button (P) on the switchbox, then squeeze one of the Start/Stop levers towards the upper handle (Q).
6. Continue to squeeze the start/stop lever towards the
upper handle and release the lock-off button (R).
7. Lower the lawnmower to its proper operating position
and commence mowing.
• NOTE - There are two start/stop levers fitted. Either one can be used for starting the lawnmower.
• IMPORTANT - Do not use the start/stop levers intermittently
To Stop your Lawnmower
1. Release the pressure on the Start/Stop lever.
How to Mow
1. Start mowing the edge of the lawn nearest to the power point so the cable is laid out on the lawn you have already
cut. (S)
2. Mow twice a week during the growing season, your lawn will suffer if more than a third of its length is cut at one time and
this may also result in poor collection.
Do Not Overload Your Mower
Mowing long thick grass may cause the motor speed to drop, you will hear a change in the motor sound. If the motor speed
drops you may overload your lawnmower which may cause damage. When mowing in long thick grass a first cut with the
cutting height set higher will help reduce the load. See Cutting Height Adjustment.
Safety Cut-Out
The Motor is protected by a Safety Cut-Out which is activated when the blade becomes jammed or if the motor is overloaded.
When this occurs, stop and remove the plug from the power supply. The Safety Cut-Out will only reset when the start/stop lever is
released. Clear any obstruction and wait for a few minutes for the Safety Cut-Out to reset before continuing to use the mower.
Removing and Fitting the Blade
S
Switch off, wait until the blade has stopped rotating
and disconnect from the mains electricity supply BEFORE attempting to remove or refit the blade.
Always handle the blade with care - sharp edges
could cause injury. USE GLOVES.
Removing the Blade
1. To remove the blade bolt, hold the blade firmly with a
gloved hand and with a spanner, loosen the blade bolt
by turning it anti-clockwise (S).
2. Remove the blade bolt, washer and blade.(S)
3. Inspect for damage and clean as necessary.
4. In the event of a blade becoming difficult to remove,
insert a screwdriver (T1) into the hole (T2) to lock the
drive, then use a spanner (13mm A/F) to loosen the
blade bolt by turning the spanner anti-clockwise. Ensure the screwdriver is removed before atempting to
turn on the machine.
Renew your metal blade after 50 hours mowing or 2
years whichever is the sooner - regardless of condition. If the blade is cracked or damaged replace it
with a new one.
Fitting the Blade
1. Fit the blade to the shaft with the sharp edges of the
blade pointing away from the shaft and you are able
to read the text on the blade ʻThis side to grassʼ
2. Re-assemble blade bolt through the washer and the blade.
3. Hold the blade firmly with a gloved hand and tighten the
blade bolt firmly with a spanner . Do not over tighten.
blade bolt
washer
blade
T
1
2
Caring for your Lawnmower
V1
Cleaning
• USE GLOVES
• IMPORTANT:- It is very important that you keep your lawnmower clean. Grass clippings left in any of the air intakes or
under the deck could become a potential fire hazard.
1. Remove grass from under the deck with brush. (V1)
2. Using a soft brush - remove grass clippings from all
air intakes (V2), the discharge chute (V3) and the
grass box (V4).
3. Visimo Only - Using a soft brush, remove grass clippings from the vision window (V5).
4. Wipe over the surface of your lawnmower with a dry
cloth (V6).
• IMPORTANT:- Never use water for cleaning your lawnmower. Do not clean with chemicals, including petrol, or
solvents - some can destroy critical plastic parts.
Storing your Cable (Visimo & Rollermo only)
• Your electric cable can be wrapped around the cable
wrap wing knobs to enable tidy and safe storage (W1).
Storing your Lawnmower:
• Loosen the wing knobs to enable the handles to be
folded over the product (W2).
• Store in a dry place where your lawnmower is protected from damage
At the End of the Mowing Season
1. Replace blade, bolts, nuts or screws, if necessary.
2. Clean your lawnmower thoroughly.
3. Make sure that the electric cable is stored correctly to
prevent damage.
V3
V5
V2
V4
Visimo Only
V6
W2
W1
Fault Finding Hints
Fails to Operate
1. Is the correct Starting procedure being followed? See ʻTo
Start your Lawnmowerʼ
2. Is the Power Turned On?
3. Check the fuse in the plug, if blown replace.
4. Fuse continues to blow?
Immediately disconnect from the mains electricity supply and consult your local approved Service Centre.
Poor Grass Collection
1. Disconnect from the mains electricity supply.
2. Clean the outside of the air intakes, the discharge chute
and the underside of the deck.
3. Raise to a higher height of cut. See Cutting Height Adjustment.
4. If poor collection persists.
Immediately disconnect from the mains electricity supply and consult your local approved Service Centre.
Excessive Vibration
1. Disconnect from the mains electricity supply.
2. Check that the blade is fitted correctly?
3. If the blade is damaged or worn, replace it with a new one.
4. If vibration persists?
Immediately disconnect from the mains electricity supply and consult your local approved Service Centre.
Lawnmower becomes heavy to push
1. Disconnect from the mains electricity supply.
2. In long grass or uneven ground, the height of cut should
be raised to a higher position. See Cutting Height Adjustment.
3. Check that the wheels and rollers can rotate freely.
4. If problem persists?
Immediately disconnect from the mains electricity supply and consult your local approved Service Centre.
Service Recommendations
1. We strongly recommend that your product is serviced at
least every twelve months, more often in a professional
application.
2. Always use genuine Spare Parts.
3. Prepacked spares are available from most Husqvarna UK
Ltd. stockists.
4. Your product is uniquely identified by a silver and black
product rating label
5. If you have a problem with your machine contact your
local Approved Service Centre ensuring you have full details of your product as described on the product rating
label.
6. Should it be necessary for work to be carried out by your
Service Centre, it is important to take your complete machine including cable and any extension cables used.
A network of specialist dealers can be found in your local
Yellow Pages.
To obtain service on your product simply telephone or visit
your local Service Centre.
Should you require service under the terms of our guarantee
the Service Centre will require proof of purchase.
All of the centres listed stock genuine Spare Parts.
NOTE: Our Service Repairers act on their own behalf and
are not empowered to commit or legally bind Husqvarna
UK Ltd. in any manner whatsoever.
Guarantee & Guarantee Policy
If any part is found to be defective due to faulty manufacture
within the guarantee period, Husqvarna UK Ltd., through its
Authorised Service Repairers will effect the repair or replacement to the customer free of charge providing:
(a) The fault is reported directly to the Authorised Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty adjustment by the user.
(d) The failure has not occurred through fair wear and tear.
(e) The machine has not been serviced or repaired, taken
apart or tampered with by any person not authorised by
Husqvarna UK Ltd..
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used commercially.
*
This guarantee is additional to, and in no way diminishes the customers statutory rights.
Failures due to the following are not covered, therefore it is important that you read the instructions contained in this Operator's Manual and understand how to operate and maintain your
machine:
Failures not covered by guarantee
*
Replacing worn or damaged blades.
*
Failures as a result of not reporting an initial fault.
*
Failures as a result of sudden impact.
*
Failures as a result of not using the product in accordance with the instructions and recommendations contained in this Operator's Manual.
*
Machines used for hire are not covered by this guarantee.
*
The following items listed are considered as wearing
parts and their life is dependent on regular maintenance
and are, therefore not normally subject to a valid warranty claim: Blades, Electric Mains cable
*
Caution!
Husqvarna UK Ltd. does not accept liability under the
warranty for defects caused in whole or part, directly or
indirectly by the fitting of replacement parts or additional
parts that are not either manufactured or approved by
Husqvarna UK Ltd., or by the machine having been
modified in any way.
Environmental Information
•
•
Awareness of the environment must be considered
when disposing of ʻend-of-lifeʼ product.
If necessary, contact your local authority for disposal
information.
The symbol
on the product or on its packaging indicates that this product may not be treated as household
waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic
equipment.
By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the environment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
For more detailed information about recycling of this
product, please contact your local council office, your
household waste disposal service or the shop where you
purchased the product.
EC Declaration of Conformity
Husqvarna UK Ltd., Aycliffe Industrial Park
Newton Aycliffe, Co. Durham, DL5 6UP, England
Declare under our sole responsibility that the product(s);
Category........................................ Electric Rotary Lawnmower
Model(s)......................................... VTR32, VM032, RM032, EM032
Identification of Series................... See Product Rating Label
Year of Construction...................... See Product Rating Label
Complies with the essential requirements & provisions of the following EC Directives:
98/37/EC (until 31.12.09), 2006/42/EC (from 01.01.10), 2004/108/EC, 2000/14/EC
based on the following EU harmonized standards applied:
EN60335-1, EN60335-2-77, EN836, EN50366, EN55014-1, EN61000-3-2, EN61000-3-3
The maximum A weighted sound pressure level LpA at the operatorʼs position, recorded on a sample of the above
product(s) corresponds to the Level given in the table.
The maximum hand / arm vibration weighted value measured according to EN ISO 5349 on a sample of the above
product(s) corresponds to the Value given in the table.
2000/14/EC: The Measured Sound Power LWA & Guaranteed Sound Power LWA values are according to the tabulated
figures.
Conformity Assessment Procedure.................. Annex VI
Notified Body.................................................... Intertek, Cleeve Road
Leatherhead, Surrey
KT22 7SB, England
Newton Aycliffe, 03/04/2009
M. Bowden,
Research & Development Director
Husqvarna UK Ltd.
Keeper of technical documentation
Type
Width of Cut (cm)
Speed of Rotation of Cutting Device (RPM)
Power (W)
Measured Sound Power LWA (dB(A))
Guaranteed Sound Power LWA (dB(A))
Level (dB(A))
Value (m/s )
Weight (Kg)
2
VTR32
32
3,600
1000
95
96
80.2
2.08
8.69
VM032
32
3,600
1100
95
96
80.2
2.08
9.09
VM032+
32
3,600
1200
95
96
80.2
2.08
9.09
RM032
32
3,600
1000
95
96
80.2
2.08
8.97
EM032
32
3,600
900
95
96
80.2
2.08
8.74
EM032+
32
3,600
1000
95
96
80.2
2.08
8.74
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.
Copyright © 2008 Flymo S.A. All rights reserved. Flymo® and other product and feature names are registered or unregistered
trademarks of Flymo S.A.
Husqvarna UK Ltd.
Aycliffe Industrial Park
NEWTON AYCLIFFE
Co.Durham DL5 6UP
ENGLAND
Telephone - 01325 302 302 Fax - 01325 310339
5054853-02
Download PDF
Similar pages
IPL, Flymo, Power Compact 330, PC330, 964330401, 964330467
OM, Flymo, Chevron 34C, Chevron 34VC, Chevron 37C, Chevron 37VC, 9666185-01, 9666186-01, 9667745-01, 9667746-01, 2014
OM, Flymo, Chevron 34 C, Chevron 34 VC, 966618501, 966618601, 2010
OM, Flymo, Venturer 32, Visimo, Rollermo, Easimo, 964322301, 964322401, 964322501, 966855101, 2007
OM, Flymo, Venturer 32, Visimo, Rollermo, Easimo, RE320, 966855101, 964322301, 964322401, 964322501, 966516527, 2009
OM, Flymo, Venturer 32, Visimo, Rollermo, Easimo, RE320
OM, Flymo, Chevron 34VC, Chevron 37C, 966618699, 966774599, 2013
OM, Flymo, Chevron 32V, 966608401, 966608428, 966608432, 2015-10
OM, Flymo, Chevron 32 VC, 966608501, 2010
OM, Flymo, Speedi-Mo, Chevron 32 V, 966608301, 966608401, 2010
OM, Flymo, Speedi-Mo, Chevron 32 V, 966608301, 966608401, 2011
OM, Flymo, Multimo 340, 966953701, 2008
Philips 28PT842A/32 CRT Television User Manual
OM, Flymo, Hover Vac 2800, 963257401, 2008
OM, Flymo, Multimo 360, Multimo 360 XC, 964336201, 964336199, 2007
Flymo EM032 Lawn Mower User Manual
OM, Flymo, Visimo, 964322025, 964322525, 964322325, 2008
OM, Flymo, Multimo 340 XC, Multimo 360, Multimo 360 XC, Multimo 420, Multimo 420 XC, 966953801, 966839001, 966957601, 966959101, 966959299, 2008
Fisher-Price V4340 Baby Monitor User Manual
Worx WG701E Technical data
OM, Flymo, Hover Vac, Mow n Vac 28, 963257401, 966671201, 2011
Dodge 2008 Ram 3500 Automobile User Manual