Force10 Networks 100-00055-01 Network Card User Manual

LED
Power
Status
Port 1 to 8
(Right LED)
Port 1 to 8
(Left LED)
Port 9 and 10
State
Description
Green
The FortiGate unit is on.
Off
The FortiGate unit is running abnormally.
Green
The FortiGate unit is running normally.
Flashing Green
The FortiGate unit is running abnormally.
Off
The FortiGate unit is off.
Green
The correct cable is in use and the connected equipment has power.
Flashing
Green
Network activity at this interface.
Off
No link established.
Green
Connection at 1000 Mb
Amber
Connection at 100 Mb
Off
Connection at 10 Mb
Green
The correct cable is in use and the connected equipment has power.
Flashing Green
Network activity at this interface.
QuickStart Guide
FortiGate-3810A-LENC
ASM1
ADM1
3810A-LENC
ASM2
Esc
ADM2
USB
Enter
CONSOLE
1
AUX
2
3
4
5
6
7
9
8
10
STATUS
POWER
Visit these links for more information and documentation for your Fortinet product.
• Technical Documentation - http://docs.forticare.com
• Fortinet Knowledge Center - http://kc.forticare.com
• Fortinet Technical Support - http://support.fortinet.com
© Copyright 2008 Fortinet Incorporated. All rights reserved.
Products mentioned in this document are trademarks or registered trademarks
of their respective holders.
Regulatory Compliance
FCC Class B Part 15 CSA/CUS
6 June 2008
01-30006-0478-20080606
Package Contents
Connector
Type
Speed
Protocol
Description
Ports 1 to 8
RJ-45
1000 Base-T
Ethernet
Copper gigabit connection to 10/100/1000 copper networks.
Ports 9 and 10
LC SFP
1000Base-SX
Ethernet
Multimode fiber optic connections to gigabit optical networks for small packet performance
required for voice, video and other multimedia streaming applications.
CONSOLE
RJ-45
9600 bps
8/N/1
RS-232
serial
Optional connection to the management computer. Provides access to the command line
interface (CLI).
USB
USB
USB
Optional connection to a USB key for firmware backup and installation.
ASM1
ADM1
3810A-LENC
ASM2
Esc
ADM2
USB
Enter
CONSOLE
AUX
1
2
3
4
5
6
7
8
9
QuickStart Guide
10
STATUS
POWER
FortiGate-30B
x2 SFP
Transceivers
Optional RJ-45 to DB-9 cable connects
to serial port on management computer
ASM1
Straight-through Ethernet cables
connect to the Internet or other
networks
ADM1
3810A-LENC
ASM2
Esc
Fiber optic cable connects
to internal network or Internet
ADM2
USB
Enter
CONSOLE
AUX
1
2
3
4
5
6
7
8
9
10
STATUS
POWER
RJ-45 to
DB-9 Serial Cable
Straight-through
and cross over
Ethernet cables
Tools and Documenation
FortiGate
Copyright 2008 Fortinet Incorporated. All rights reserved.
Trademarks
Products mentioned in this document are trademarks.
Power alarm
reset button
Welcome | Bienvenue | Willkommen | ?迎 | 歓迎 | Bienvenido | Benvenuto
Rack-Mount Brackets
Power Cable
Power cables connect
to power outlets
Connecting
Connect the following to the FortiGate unit. Ensure the FortiGate unit is placed on a stable
surface or install in a standard 19 inch rack.
ASM1
ADM1
3810A-LENC
ASM2
Esc
ADM2
USB
Enter
CONSOLE
AUX
1
2
3
4
5
6
7
8
9
10
STATUS
POWER
•
Insert a network cable to port 1. Insert the other end to the router connected to the Internet, or to the modem.
•
Connect a network cable to the Internal port. Insert the other end to a computer or
switch.
•
Connect the AC Power Cord to the Power Supply.
•
Connect the redundant DC Power Supply to the FortiGate unit if applicable.
•
Connect the Power Cord to a surge protected power bar or power supply.
Optional RJ-45 to DB-9 cable connects
to serial port on management computer
Straight-through Ethernet cables
connect to the Internet or other
networks
Fiber optic cable connects
to internal network or Internet
Power alarm
reset button
Power cables connect
to power outlets
Configuration Tools
Web-based manager
Command Line Interface (CLI)
The FortiGate web-based manager is an easy to use management tool.
Use it to configure the administrator password, the interface and default gateway addresses,
and the DNS server addresses.
The CLI is a full-featured management tool. Use it to configure the administrator password,
the interface addresses, the default gateway address, and the DNS server addresses. To
configure advanced settings, see the Tools and Documentation CD included with the
FortiGate unit.
Requirements:
•
An Ethernet connection between the FortiGate unit and management computer.
•
A web browser such as FireFox or Internet Explorer on the management computer.
Requirements:
•
The RJ-45 to DB9 serial connection between the FortiGate unit and management computer.
•
A terminal emulation application (HyperTerminal for Windows) on the management
computer.
Collecting Information
NAT/Route Mode
Port
Port
Port
Port
Port
General settings
IP:
____.____.____.____
Administrator password:
Netmask:
____.____.____.____
Network Settings:
Default Gateway:
____.____.____.____
IP:
____.____.____.____
Primary DNS Server:
____.____.____.____
Netmask:
____.____.____.____
Secondary DNS Server:
____.____.____.____
IP:
____.____.____.____
Netmask:
____.____.____.____
IP:
____.____.____.____
Netmask:
____.____.____.____
IP:
____.____.____.____
Netmask:
____.____.____.____
The internal interface IP address and netmask must be valid for the internal network.
Transparent mode
Management IP:
IP:
____.____.____.____
Netmask:
____.____.____.____
The management IP address and netmask must be valid for the network from which you will
manage the FortiGate unit.
A default gateway is required for the FortiGate unit to route connections to the Internet.
Factory default settings
NAT/Route mode
Transparent mode
Port 1 interface
192.168.1.99
Management IP
Port 2 interface
192.168.100.99
Administrative account settings
0.0.0.0
Port 3 to 10 interface
0.0.0.0
User name
admin
DHCP server on Internal
interface
192.168.1.110
– 192.168.1.210
Password
(none)
To reset the FortiGate unit to the factory defaults, in the CLI type the command
execute factory reset
Configuring
NAT/Route mode
Transparent mode
You would typically use NAT/Route mode when the FortiGate unit is deployed as a gateway
between private and public networks. In its default NAT/Route mode configuration, the unit
functions as a firewall. Firewall policies control communications through the FortiGate unit.
You would typically use the FortiGate unit in Transparent mode on a private network behind
an existing firewall or behind a router. In its default Transparent mode configuration, the unit
functions as a firewall.
Upgrading to High Encryption
This FortiGate unit has a factory installed low encryption feature set. You can purchase a high encryption upgrade within 90 days of shipment from Fortinet. Fortinet Technical Support can
provide a high encryption license key once you have provided suitable documentation that the necessary export licenses have been granted for your region, and our legal department has
authorized the use of high encryption.
When you receive the high encryption license key, in the CLI, enter the command exec crypto-license <high-enc-key>.
Fortinet does not guarantee that the customer will receive a export license upon purchase of the product or license key.
Web-based Manager
Command Line Interface
1.
1.
2.
3.
4.
Connect the FortiGate internal interface to a management computer Ethernet interface.
Use a cross-over Ethernet cable to connect the devices directly. Use straight-through
Ethernet cables to connect the devices through a hub or switch.
Configure the management computer to be on the same subnet as the internal interface
of the FortiGate unit. To do this, change the IP address of the management computer to
192.168.1.2 and the netmask to 255.255.255.0.
To access the FortiGate web-based manager, start Internet Explorer and browse to
https://192.168.1.99 (remember to include the “s” in https://).
Type admin in the Name field and select Login.
NAT/Route mode
2.
3.
4.
NAT/Route mode
1.
Configure the FortiGate internal interface.
config system interface
edit internal
set ip <intf_ip>/<netmask_ip>
end
2.
Repeat to configure each interface, for example, to configure the Port 1 interface.
config system interface
edit port1
...
3.
Configure the primary and secondary DNS server IP addresses.
config system dns
set primary <dns-server_ip>
set secondary <dns-server_ip>
end
4.
Configure the default gateway.
config router static
edit 1
set gateway <gateway_ip>
end
To change the administrator password
1. Go to System > Admin > Administrators.
2. Select Change Password for the admin administrator and enter a new password.
To configure interfaces
1. Go to System > Network > Interface.
2. Select the edit icon for each interface to configure.
3. Set the addressing mode for the interface. (See the online help for information.)
•
For manual addressing, enter the IP address and netmask for the interface.
•
For DHCP addressing, select DHCP and any required settings.
•
For PPPoE addressing, select PPPoE, and enter the username and password and
any other required settings.
To configure the Primary and Secondary DNS server IP addresses
1. Go to System > Network > Options, enter the Primary and Secondary DNS IP addresses that you recorded above and select Apply.
To configure a Default Gateway
1. Go to Router > Static and select Edit icon for the static route.
2. Set Gateway to the Default Gateway IP address you recorded above and select OK.
Transparent mode
Transparent Mode
1.
Change from NAT/Route mode to Transparent mode and configure the Management IP
address.
config system settings
set opmode transparent
set manageip <mng_ip>/<netmask>
set gateway <gateway_ip>
end
2.
Configure the DNS server IP address.
config system dns
set primary <dns-server_ip>
set secondary <dns-server_ip>
end
To switch from NAT/route mode to transparent mode
1. Go to System > Config > Operation Mode and select Transparent.
2. Set the Management IP/Netmask to 192.168.1.99/24.
3. Set a default Gateway and select Apply.
To change the administrator password
1. Go to System > Admin > Administrators.
2. Select Change Password for the admin administrator and enter a new password.
To change the management interface
1. Go to System > Config > Operation Mode.
2. Enter the Management IP address and netmask that you recorded above and select
Apply.
Use the RJ-45 to DB9 serial cable to connect the FortiGate Console port to the management computer serial port.
Start a terminal emulation program (HyperTerminal) on the management computer. Use
these settings:
Baud Rate (bps) 9600, Data bits 8, Parity None, Stop bits 1, and Flow Control None.
At the Login: prompt, type admin and press Enter twice (no password required).
To configure the Primary and Secondary DNS server IP addresses
1. Go to System > Network > Options, enter the Primary and Secondary DNS IP addresses that you recorded above and select Apply.
Refer to the Tools and Documentation CD for information on how to control traffic, and how to configure HA, antivirus protection, FortiGuard, Web content filtering, Spam filtering, intrusion
prevention (IPS), and virtual private networking (VPN).