Ford 2006 Freestar Automobile User Manual

IMAGETEAM™ 4410/4710
2D Series Hand Held Imager
™
User’s Guide
Statement of Agency Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC Class B Compliance Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio or television technician for help.
Caution: Any changes or modifications made to this device that are not
expressly approved by Hand Held Products, Inc. may void the user’s authority to
operate the equipment.
Note: To maintain compliance with FCC Rules and Regulations, cables
connected to this device must be shielded cables, in which the cable shield
wire(s) have been grounded (tied) to the connector shell.
Canadian Notice
This equipment does not exceed the Class B limits for radio noise emissions as
described in the Radio Interference Regulations of the Canadian Department of
Communications.
Le present appareil numerique n’emet pas de bruits radioelectriques depassant
les limites applicables aux appareils numeriques de la classe B prescrites dans
le Reglement sur le brouillage radioelectrique edicte par le ministere des
Communications du Canada.
LED Safety Statement
This device has been tested in accordance with EN60825-1 LED safety, and has
been certified to be under the limits of a Class 1 LED device.
The CE mark on the product indicates that the system has been tested
to and conforms with the provisions noted within the 89/336/EEC
Electromagnetic Compatibility Directive and the 73/23/EEC Low
Voltage Directive.
For further information please contact:
Hand Held Products, Inc.
Nijverheidsweg 9
5627 BT Eindhoven
The Netherlands
Hand Held Products shall not be liable for use of our product with equipment (i.e.,
power supplies, personal computers, etc.) that is not CE marked and does not
comply with the Low Voltage Directive.
Patents
Please refer to the product packaging for patent information.
Disclaimer
Hand Held Products, Inc. (“Hand Held Products”) reserves the right to make
changes in specifications and other information contained in this document
without prior notice, and the reader should in all cases consult Hand Held
Products to determine whether any such changes have been made. The
information in this publication does not represent a commitment on the part of
Hand Held Products.
Hand Held Products shall not be liable for technical or editorial errors or
omissions contained herein; nor for incidental or consequential damages
resulting from the furnishing, performance, or use of this material.
This document contains proprietary information that is protected by copyright. All
rights are reserved. No part of this document may be photocopied, reproduced,
or translated into another language without the prior written consent of Hand
Held Products.
© 2005 Hand Held Products, Inc. All rights reserved.
Web Address: www.handheld.com
Table of Contents
Chapter 1 - Introduction and Installation
About the Hand-Held and Fixed Mount 2D Imager............. 1-1
Unpacking the Imager........................................................... 1-2
IT4410 Imager Identification................................................ 1-4
IT4710 Imager Identification................................................ 1-5
Connecting the Scanner in Keyboard Wedge Mode............. 1-6
Connecting the Scanner to a Serial Port ............................... 1-7
Reading Techniques.............................................................. 1-8
Chapter 2 - Programming
Introduction........................................................................... 2-1
Reset Factory Settings .......................................................... 2-2
Status Check ......................................................................... 2-2
All Symbologies ................................................................... 2-2
Revision Selections............................................................... 2-3
Terminal Interface ................................................................ 2-4
Supported Terminals Chart................................................... 2-5
Keyboard Country ................................................................ 2-6
Keyboard Style ..................................................................... 2-7
Keyboard Modifiers.............................................................. 2-8
Keyboard Function Relationships......................................... 2-9
Communication Settings..................................................... 2-10
Parity ............................................................................ 2-10
Baud Rate ..................................................................... 2-11
Word Length Data Bits ................................................ 2-12
Word Length Stop Bits................................................. 2-12
Hardware Flow Control................................................ 2-13
Software Flow Control................................................. 2-13
Serial Triggering .......................................................... 2-14
Trigger Timeout.................................................................. 2-15
Power Saving Mode............................................................ 2-16
Power Hold Mode............................................................... 2-17
LED Power Level ............................................................... 2-17
LED Flashing...................................................................... 2-18
i
Aimer Delay........................................................................ 2-18
Aimer Interval..................................................................... 2-19
Centering............................................................................. 2-20
AutoTrigger ........................................................................ 2-23
Scan Stand .......................................................................... 2-23
Scan Stand Symbol ...................................................... 2-24
Presentation Mode .............................................................. 2-24
Presentation Re-trigger Delay ...................................... 2-24
Presentation Lights....................................................... 2-25
Presentation Default ..................................................... 2-25
Fast Omni Mode ................................................................. 2-26
Beeper Volume ................................................................... 2-26
Power Up Beeper................................................................ 2-27
Output Sequence Beeper..................................................... 2-27
Beep On Decode ................................................................. 2-27
Beeper Default ............................................................. 2-27
Intercharacter, Interfunction,
and Intermessage Delays.................................................. 2-28
Intercharacter Delay .................................................... 2-28
User Specified Intercharacter Delay ........................... 2-28
Interfunction Delay ..................................................... 2-29
Intermessage Delay ..................................................... 2-30
Prefix/Suffix Overview....................................................... 2-31
Adding a Prefix or Suffix............................................. 2-32
Add a Carriage Return Suffix to All Symbologies ..... 2-33
Add a Code I.D. Prefix to All Symbologies ................ 2-33
Add an AIM I.D. Prefix to All Symbologies .............. 2-33
Prefix Entries................................................................ 2-34
Suffix Entries ............................................................... 2-34
Symbology Chart ................................................................ 2-35
Decimal to Hex to ASCII Conversion Chart ...................... 2-36
ii
Data Format Editor Overview............................................. 2-37
Format Editor Commands ............................................ 2-38
Data Format Editor....................................................... 2-40
Data Formatter.............................................................. 2-41
Require Data Format .................................................... 2-41
Show Data Formats ...................................................... 2-41
Alternate Data Formats ................................................ 2-42
Output Sequence Overview ................................................ 2-43
Require Output Sequence............................................. 2-44
Output Sequence Editor................................................ 2-46
Multiple Symbols................................................................ 2-47
No Read .............................................................................. 2-47
Print Weight ........................................................................ 2-48
Function Code Transmit ..................................................... 2-48
Video Reverse..................................................................... 2-49
Chapter 3 - Symbologies
Introduction........................................................................... 3-1
Codabar ................................................................................. 3-2
Start/Stop Characters...................................................... 3-2
Message Length.............................................................. 3-2
Check Character ............................................................. 3-3
Code 39 ................................................................................. 3-4
Start/Stop Characters...................................................... 3-4
Message Length.............................................................. 3-5
Full ASCII ...................................................................... 3-5
Check Character ............................................................. 3-6
Code 11 ................................................................................. 3-7
Message Length.............................................................. 3-7
Check Digits Required ................................................... 3-8
Interleaved 2 of 5 .................................................................. 3-9
Message Length.............................................................. 3-9
Check Digit................................................................... 3-10
IATA 2 of 5......................................................................... 3-11
Message Length............................................................ 3-11
iii
MSI ..................................................................................... 3-12
Message Length ........................................................... 3-12
Check Digit .................................................................. 3-13
Code 93............................................................................... 3-14
Message Length ........................................................... 3-14
Code 128............................................................................. 3-15
Message Length ........................................................... 3-15
ISBT.................................................................................... 3-16
EAN/JAN 8......................................................................... 3-17
Check Digit .................................................................. 3-17
EAN/JAN 8 Addenda................................................... 3-18
EAN/JAN 8 Addenda Required ................................... 3-18
EAN/JAN 8 Addenda Separator .................................. 3-18
EAN/JAN 13....................................................................... 3-19
Check Digit .................................................................. 3-19
EAN/JAN 13 Addenda................................................. 3-20
EAN/JAN 13 Addenda Required ................................. 3-20
EAN/JAN 13 Addenda Separator ................................ 3-20
UPC A................................................................................. 3-21
Check Digit .................................................................. 3-21
Number System............................................................ 3-21
UPC A Addenda........................................................... 3-22
UPC A Addenda Required ........................................... 3-22
UPC A Addenda Separator .......................................... 3-22
UPC E0 ............................................................................... 3-23
Check Digit .................................................................. 3-23
Number System............................................................ 3-23
Version E Expand ........................................................ 3-24
UPC E1 ............................................................................... 3-24
UPC E0/E1 Addenda.................................................... 3-24
UPC E0/E1 Addenda Required.................................... 3-25
UPC E0/E1 Addenda Separator ................................... 3-25
RSS-14................................................................................ 3-26
RSS-14 Limited .................................................................. 3-26
RSS-14 Expanded............................................................... 3-27
Message Length ........................................................... 3-27
iv
Codablock ........................................................................... 3-28
Message Length............................................................ 3-28
PDF417 ............................................................................... 3-29
Message Length............................................................ 3-29
MicroPDF417 ..................................................................... 3-30
Message Length............................................................ 3-30
Code 49 ............................................................................... 3-31
Message Length............................................................ 3-31
EAN•UCC Composite Codes ............................................. 3-32
Message Length............................................................ 3-32
TLC39 ................................................................................. 3-33
U.S. Postal Service POSTNET Code.................................. 3-34
Check Digit................................................................... 3-34
Planet Code ......................................................................... 3-34
Check Digit................................................................... 3-34
British Post Office 4 State Code ........................................ 3-35
Canadian 4 State Code ........................................................ 3-35
Dutch Postal Code............................................................... 3-35
Australian 4 State Code ...................................................... 3-35
Japanese Postal Service....................................................... 3-35
QR Code.............................................................................. 3-36
Message Length............................................................ 3-36
Data Matrix ......................................................................... 3-37
Message Length............................................................ 3-37
MaxiCode............................................................................ 3-38
Message Length............................................................ 3-38
Structured Carrier Message Only ................................. 3-39
Aztec Code.......................................................................... 3-40
Message Length............................................................ 3-40
Test Menu .......................................................................... 3-41
2D PQA (Print Quality Assessment) .................................. 3-41
Chapter 4 - OCR Programming
Introduction........................................................................... 4-1
OCR ...................................................................................... 4-2
OCR Direction................................................................ 4-3
v
Creating OCR Templates...................................................... 4-4
Creating an OCR Template............................................ 4-4
Stringing Together Multiple Formats
(Creating “Or” Statements) ............................................ 4-6
Creating a User-Defined Variable.................................. 4-6
Adding an OCR Check Character .................................. 4-7
OCR Template Codes .................................................... 4-9
Chapter 5 - Default Charts
Communication (RS-232) Selections............................. 5-1
Imager Selections ........................................................... 5-1
Prefix/Suffix Selections................................................. 5-2
Data Formatter Selections .............................................. 5-2
Output Sequence Selections........................................... 5-2
Linear Symbologies ....................................................... 5-2
Postal Symbology Selections ......................................... 5-4
2D Matrix Selections...................................................... 5-4
OCR Selections .............................................................. 5-5
Chapter 6 - Software Development Kit
Software Development Kit (SDK)........................................ 6-1
Features of the SDK.............................................................. 6-1
Chapter 7 - Quick*View
Quick*View Demonstration Software Instructions.............. 7-1
Setting Up the Imager and the Quick*View Software... 7-1
Installing Quick*View from the Web................................... 7-1
Using the Quick*View Software .......................................... 7-3
Load New Imager Software ........................................... 7-8
Serial Programming Commands .................................... 7-9
Query Commands .............................................................. 7-11
Trigger Commands ............................................................. 7-12
Serial Programming Commands ........................................ 7-14
vi
Imaging Commands ........................................................... 7-27
Image Commands Help File......................................... 7-27
Image Ship.................................................................... 7-27
Image Capture/Ship and Image Get Commands .......... 7-28
Image Cropping/Shipping Example ............................. 7-29
Intelligent Signature Capture Commands .................... 7-29
Chapter 8 - Visual Menu
Visual Menu Introduction ..................................................... 8-1
Installing Visual Menu from the Web............................ 8-2
Chapter 9 - Interface Keys
Chapter 10 - Product Specifications & Pinouts
Product Specifications - IT4410 ......................................... 10-1
Product Specifications - IT4710 ......................................... 10-2
Depth of Field Charts.......................................................... 10-4
Cable Pinouts ...................................................................... 10-6
Connector Part Numbers .............................................. 10-7
IT4410 Dimensions............................................................. 10-8
IT4710 Dimensions............................................................. 10-9
Chapter 11 - Maintenance & Troubleshooting
Repairs ................................................................................ 11-1
Maintenance........................................................................ 11-1
Replacing the Interface Cable ...................................... 11-2
Troubleshooting .................................................................. 11-3
Chapter 12 - Customer Support
Product Service and Repair................................................. 12-1
Online Product Service and Repair Assistance ............ 12-2
Technical Assistance........................................................... 12-2
Online Technical Assistance ........................................ 12-2
Limited Warranty................................................................ 12-2
vii
viii
1
Introduction and Installation
About the Hand-Held and Fixed Mount 2D Imager
The hand-held and fixed mount 2D Imager is an economical, durable solution for
a wide variety of data collection applications. The Imager features the following:
• A tough, ergonomic thermoplastic housing for comfort and durability.
• Omni-directional reading of a variety of printed symbols, including the most
popular linear and 2D matrix symbologies.
• RS-232, keyboard wedge, and laser emulation communication outputs.
• The ability to capture and download images to a PC for signature capture
software applications, and PC-based decoding.
• The ability to read OCR fonts.
About this Manual
This user’s guide provides installation instructions for the hand-held Imager. The
chapters contain the following information:
Chapter 1
Chapter 2
Chapter 3
Chapter 4
Chapter 5
Chapter 6
Chapter 7
Unpacking and installing the Imager
Programming selections
Symbology programming selections
OCR programming
Default settings
Software Developers Kit
Quick*View software information and serial programming
commands
Chapter 8 Visual Menu software
Chapter 9 Interface Keys
Chapter 10 Product Specifications & Pinouts
Chapter 11 Maintenance and troubleshooting
Chapter 12 Customer support, service information, and warranty
IMAGETEAM™ 4410/4710 User’s Guide
1-1
Unpacking the Imager
Open the carton. The shipping carton or container should contain:
IMAGETEAM 4410 Convenience Kit:
IMAGETEAM 4410 Hand
Held Imager
Universal Power Supply
and Power Cable
Cable
IMAGETEAM 4710 Convenience Kit:
IMAGETEAM 4710 Hand
Held/Fixed Mount Imager
Universal Power Supply
and Power Cable
Cable
1-2
IMAGETEAM™ 4410/4710 User’s Guide
• Check to make sure everything you ordered is present.
• Save the shipping container for later storage or shipping.
• Check for damage during shipment. Report damage immediately to the
carrier who delivered the carton.
IMAGETEAM™ 4410/4710 User’s Guide
1-3
IT4410 Imager Identification
Model # - 4410XX-XX
Manufactured - August 2002
Serial # = P-12-34567
S/W = 34567001/4410
Enlarged View of Label
Hand Held IT4410 Imager
Bottom View
1-4
IMAGETEAM™ 4410/4710 User’s Guide
IT4710 Imager Identification
Hand Held IT4710 Imager
Bottom View
ITEM # IT4710
DATE / SN:
S / W Rev:
Hand Held Products
Skaneateles Falls, NEW YORK
13153
IMAGETEAM™ 4410/4710 User’s Guide
1-5
Connecting the Scanner in Keyboard Wedge Mode
A scanner can be connected between the keyboard and PC as a “keyboard
wedge,” plugged into the serial port, or connected to a portable data terminal in
non decoded output mode.
Note: Note: The IMAGETEAM 4410 and 4710 scanners are factory
programmed for a keyboard wedge interface to an IBM PC AT with a USA
keyboard.
The following is an example of a keyboard wedge connection:
1. Turn off power to the terminal/computer.
2. Disconnect the keyboard cable from
the back of the terminal/computer.
Disconnect
3. Connect the
appropriate interface
cable to the scanner
and to the terminal/
computer. The
scanner will beep
twice.
4. Connect the power
supply (4 to 9V).
1
3
5. Turn the terminal/
computer power back
on.
6. Verify the scanner
operation by scanning
a bar code. The
scanner will beep
once.
2
4
The scanner is now connected and ready to communicate with your terminal/PC.
You must program the scanner for your interface before bar code data can be
transmitted to your terminal/PC. If you are using the scanner as a keyboard
wedge, see"Terminal Interface" on page 2-4. If the scanner is connected via a
serial port, turn to "Connecting the Scanner to a Serial Port" on page 1-7.
1-6
IMAGETEAM™ 4410/4710 User’s Guide
Connecting the Scanner to a Serial Port
Turn off power to the terminal/computer.
1. Connect the interface cable to the scanner
2. Connect the interface cable to the 4 to 9 volt power supply and plug in the
power supply. The scanner will beep twice.
3. Connect the interface cable to the terminal/computer.
2
Power Supply
3
Interface Cable
1
4. Turn the terminal/computer power back on.
5. Verify the scanner operation by scanning a bar code from the sample bar
code section in the back of this manual. The scanner will beep once.
The scanner is now connected and ready to communicate with your terminal/PC.
Turn to "Communication Settings" on page 2-10 to program the communication
parameters for a serial interface.
IMAGETEAM™ 4410/4710 User’s Guide
1-7
Reading Techniques
The hand-held Imager has a view finder that projects a bright red aiming beam
that corresponds to the Imager’s horizontal field of view. The aiming beam
should be centered over the bar code, but it can be positioned in any direction for
a good read.
Linear bar code
2D Matrix symbol
The aiming beam is smaller when the Imager is closer to the code and larger
when it is farther from the code. Symbologies with smaller bars or elements (mil
size) should be read closer to the unit. Symbologies with larger bars or elements
(mil size) should be read farther from the unit. (see "Depth of Field Charts" on
page 10-4.) To read single or multiple symbols (on a page or on an object), hold
the Imager at an appropriate distance from the target, pull the trigger, and center
the aiming beam on the symbol.
1-8
IMAGETEAM™ 4410/4710 User’s Guide
2
Programming
Introduction
Use this section to program the hand-held or fixed mount Imager.
This programming section contains the following menuing selections:
•
•
•
•
•
•
•
•
•
General Selections
Terminal Interface Selections
Keyboard Selections
Communication Settings
Imager Selections
Output Selections
Prefix/Suffix Selections
Data Formatter Selections
Output Sequence Selections
IMAGETEAM™ 4410/4710 User’s Guide
2-1
Reset Factory Settings
All operating parameters are stored in nonvolatile memory resident in the
Imager, where they are permanently retained in the event of a power interruption.
When you receive your Imager, certain operating parameters have already been
set. These are the factory defaults, indicated by the symbol “✱” on the
programming menu pages (beneath the default programming symbol). Default
charts begin on page 5-1.
Default
Status Check
Read the Show Software Revision symbol to transmit the software revision
level to the host terminal. The software revision will be printed out as
“REV_SW:$ProjectRevision:1.xx$;REV_WA:31204960-xxx.”
Read the Show Data Formats symbol to transmit the existing Data Format
Editor formats. One format per line will be printed out.
Show Software
Revision
Show Data Formats
All Symbologies
If you want to decode all the symbologies allowable for your scanner, scan the
All Symbologies On code.
All Symbologies
On
2-2
All Symbologies
Off
IMAGETEAM™ 4410/4710 User’s Guide
Revision Selections
Both the following programming codes would not normally be needed unless you
have a problem with the unit. An Application Support Representative may
request the boot code or power PC revision information in order to trouble shoot
a problem.
Power PC Revision
IMAGETEAM™ 4410/4710 User’s Guide
Boot Code Revision
2-3
Terminal Interface
IMAGETEAM 4410 and IMAGETEAM 4710 scanners are factory programmed
for a keyboard wedge interface to an IBM PC AT with a USA keyboard. If this is
your interface and you do not need to modify the settings, skip to "Power Saving
Mode" on page 2-16 to begin programming the scanner.
If your interface is not a standard PC AT, refer to the "Supported Terminals
Chart" on page 2-5 and locate the Terminal ID number for your PC. Scan the
Terminal ID bar code below, then scan the numeric bar code(s) on the inside
back cover of this manual to program the scanner for your terminal ID> Scan
Save to save your selection.
For example, an IBM PS/2 terminal has a Terminal ID of 002. You would scan
the Terminal ID bar code, then 0, 0, 2 from the inside back cover, then Save. If
you make an error while scanning the digits (before scanning Save), scan the
Discard code on the back cover and scan the digits and the Save code again.
Note: Factory Default for Keyboard Wedge units = 003
Note: Factory Default for True RS-232 units = 000
Terminal ID
2-4
Save
IMAGETEAM™ 4410/4710 User’s Guide
Supported Terminals Chart
Terminal
Model(s)
DEC
PC433 SE (Portable PC)
DELL
Latitude (Portable PC)
DTK
486 SLC (Portable PC)
Fujitsu
Stylistic (Portable PC)
HHLC (Code 128 Emulation)
IBM
PC XT
IBM
PS/2 25, 30, 77DX2
AT, PS/2 30-286, 50, 55SX, 60, 70,
IBM
70-061, 70-121, 80
AT
Compatibles Keyboard Emulation
IBM
(Non-wedge)
Thinkpad 360 CSE, 34, 750
IBM
(Portable PC)
Thinkpad 365, 755 CV
IBM
(Portable PC)
IBM
AT Thinkpad
Midwest
Micro Elite TS 30 PS (Portable PC)
Mitak
4022 (Portable PC)
Olivetti
M19, M24, M28, M200
Olivetti
M240, M250, M290, M380, P500
Reliasys
TR 175
RS-232 TTL
Televideo
990, 995, 9060
Texas Instruments Extensa 560CD (Portable PC)
Toshiba
2600 (Portable PC)
Toshiba
Satellite T1960, T2130, CS (Portable PC)
Zenith
Z-note (Portable PC)
IMAGETEAM™ 4410/4710 User’s Guide
Terminal
I.D.
003
003
003
003
089
001
002
003
003
097
003
106
003
003
001
003
003
000
002
003
003
003
003
2-5
Keyboard Country
Scan the Program Keyboard Country bar code below, then scan the numeric
bar code(s) from the inside back cover, then the Save bar code to program the
keyboard for your country. As a general rule, the following characters are not
supported by the scanner for countries other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~
Keyboard Country
Country Code
Scan
Belgium..................... 1
Czechoslovakia ........ 15
Denmark ................... 8
Finland...................... 2
France ...................... 3
French Canadian ...... 18
Germany/Austria....... 4
Great Britain ............. 7
Greece...................... 17
Netherlands .............. 11
Hungary .................... 19
Israel......................... 12
Italy ........................... 5
Country Code Scan
Latin America .........14
Norway...................9
Poland....................20
Portugal .................13
Romania ................25
Russia ....................26
Slovakia .................22
Spain......................10
Sweden ..................23
Switzerland ............6
Turkey Q ................24
Turkey F.................27
USA (Default) .........0
Save
2-6
IMAGETEAM™ 4410/4710 User’s Guide
Keyboard Style
This programs keyboard styles, such as Caps Lock and Shift Lock. Default =
Regular.
Regular is used when you normally have the Caps Lock key off.
Caps Lock is used when you normally have the Caps Lock key on.
Shift Lock is used when you normally have the Shift Lock key on. (Not common
to U.S. keyboards.)
Automatic Caps Lock is used if you change the Caps Lock key on and off. The
software tracks and reflects if you have Caps Lock on or off (AT and PS/2 only).
This selection can only be used with systems that have an LED which notes the
Caps Lock status.
* Regular
Caps Lock
Shift Lock
Automatic
Caps Lock
Emulate External Keyboard should be scanned if you do not have an external
keyboard (IBM AT or equivalent). To connect to a laptop, you must scan the
Emulate External Keyboard bar code below, then scan "Automatic Direct
Connect Mode On" on page 2-8. After scanning these codes, you must re-boot
your laptop.
Emulate External
Keyboard
IMAGETEAM™ 4410/4710 User’s Guide
2-7
Keyboard Modifiers
This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo
Mode.
Control + ASCII Mode On - The scanner sends key combinations for ASCII
control characters for values 00-1F. Refer to "Keyboard Function
Relationships" on page 2-9 for CTRL+ ASCII Values. Default = Off
Control + ASCII
Mode On
* Control + ASCII
Mode Off
Turbo Mode - The scanner sends characters to an IBM AT terminal faster. (For
use with IBM AT only.) If the terminal drops characters, do not use Turbo Mode.
Default = Off
Turbo Mode On
* Turbo Mode Off
Numeric Keypad Mode - Sends numeric characters as if entered from a
numeric keypad. Default = Off
Numeric Keypad
Mode On
* Numeric
Keypad Mode Off
Automatic Direct Connect - Use this selection if you are using a laptop whose
keyboard is disabled when you plug in the scanner. This selection can also be
used if you have an IBM AT style terminal and the system is dropping characters.
After scanning these codes, you must re-boot your computer. Default = Off
Automatic Direct
Connect Mode On
2-8
* Automatic Direct
Connect Mode Off
IMAGETEAM™ 4410/4710 User’s Guide
Keyboard Function Relationships
The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII
“CTRL”+ relationships apply to all terminals that can be used with the scanner.
Function Code
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
US
HEX/ASCII Value
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
Full ASCII “CTRL” +
2
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
6
-
IMAGETEAM™ 4410/4710 User’s Guide
2-9
Communication Settings
<Default All RS-232 Communication Settings>
Parity
Parity provides a means of checking character bit patterns for validity. The
Imager can be configured to operate under Mark, Space, Odd, Even, or No
(None) parity options. The host terminal must be set up for the same parity as
the Imager, to ensure reliable communication.
Mark
Space
Odd
Even
* None
2 - 10
IMAGETEAM™ 4410/4710 User’s Guide
Baud Rate
This sets the baud rate from 300 bits per second to 115,200 bits per second (see
next page). Programming baud rate causes the data to be sent at the specified
rate. The host terminal must be set to the same baud rate as the Imager to
ensure reliable communication.
300
600
1200
2400
4800
9600
19200
* 38400
IMAGETEAM™ 4410/4710 User’s Guide
2 - 11
Baud Rate, continued
57600
115200
Word Length Data Bits
You can set the Word Length at 7 or 8 bits of data per character. If an application
requires only ASCII Hex characters 0 through 7F decimal (text, digits, and
punctuation), select 7 data bits. For applications requiring use of the full ASCII
set, select 8 data bits per character.
7 Data Bits
* 8 Data Bits
Word Length Stop Bits
Word Length can be set to one or two stop bits.
* 1 Stop Bit
2 - 12
2 Stop Bits
IMAGETEAM™ 4410/4710 User’s Guide
Hardware Flow Control
When hardware flow control is On, the software checks for a CTS signal before
sending data. This option is useful when your application supports the CTS
signal.
On
* Off
Software Flow Control
This allows control of data transmission from the Imager using software
commands from the host device. When this feature is turned Off, no data flow
control is used. When Data Flow Control is turned On, the host device suspends
transmission by sending the XOFF character (DC3, hex 13) to the Imager. To
resume transmission, the host sends the XON character (DC1, hex 11). Data
transmission continues where it left off when XOFF was sent.
On
IMAGETEAM™ 4410/4710 User’s Guide
* Off
2 - 13
Serial Triggering
This provides a means of sending a serial trigger command to start and stop
decoding. When this feature is turned Off, the Imager will not respond to serial
trigger commands. When serial triggering is turned On, the Imager requires a
serial trigger character to activate scanning and decoding. The unit continues to
scan and decode until the Trigger Off character turns off the scanner, a time out
occurs, or a bar code is decoded.
On the "Decimal to Hex to ASCII Conversion Chart" on page 2-36, find the hex
characters you want to use to turn the trigger on and off. Locate the decimal
values for those characters and scan the 2 digits for each one from the
Programming Chart in the back of this manual.
When Serial Triggering is On, the default Trigger On decimal character is 18 (hex
12, DC2), and the default Trigger Off decimal character is 20 (hex 14, DC4).
On
* Off
Trigger On ‡
Trigger Off ‡
* Trigger Defaults
2 - 14
IMAGETEAM™ 4410/4710 User’s Guide
Note: ‡
A one to three digit decimal number and
Save are required after reading this programming symbol. See "Decimal
to Hex to ASCII Conversion Chart" on page 2-36, and the Programming
Chart (inside back cover).
Trigger Timeout
Use this selection to set a timeout (in quarter seconds) of the Imager’s trigger.
Once the imager has timed out, it must be triggered again either serially (see
"Serial Triggering" on page 2-14), or manually. Set the Trigger Timeout to 00 if
you don’t want a Trigger Timeout. Default setting = 120 seconds
Set Timeout ‡
IMAGETEAM™ 4410/4710 User’s Guide
2 - 15
Note: ‡
A one- to three digit number and Save are
required after reading this programming symbol. Refer to the
Programming Chart (inside back cover).
Power Saving Mode
This provides control of the Imager’s power consumption, as follows:
Low Power draws low (50%) LED current during image capture, allowing one
read attempt only for each trigger pull. The Imager is less tolerant of hand
movement during the read attempt, and powers down after the image capture is
complete.
Medium Power draws a normal LED current during image capture which
enhances motion tolerance. Medium Power attempts to read as long as the
trigger is pulled, going into a “doze” (low power) state after each read attempt.
The Imager powers down ten seconds after the image capture is complete.
Normal Power draws a normal LED current, attempting to read as long as the
trigger is pulled or a decode is in process. The Imager doesn’t go into a “doze”
state after each read attempt, but will power down after two minutes if Power
Hold Mode is turned Off.
Low Power
Medium Power
* Normal Power
2 - 16
IMAGETEAM™ 4410/4710 User’s Guide
Power Hold Mode
Power Hold On keeps the Imager in a ready to read state. To conserve power,
this selection may be turned Off and the unit will power down if not used within
two minutes. When you are ready to use the Imager again, restore power by
pressing the trigger.
On
* Off
LED Power Level
This selection allows you to adjust LED brightness.
Off is used when no illumination is needed. Low is used if low illumination is
sufficient. High (the default) is the brightest setting.
Off
Low
* High
IMAGETEAM™ 4410/4710 User’s Guide
2 - 17
LED Flashing
When LED Flashing is On, the LEDs and aiming light alternately flash until a
symbol is decoded or the trigger is released.
If LED Flashing is turned Off, the average current draw is increased and the
aiming light won’t illuminate while the scanner reads a bar code. The LEDs
remain on while the scanner is reading.
Off
* On
Aimer Delay
The aimer delay allows a delay time for the operator to aim the scanner before
the picture is taken. Use these codes to set the time between when the trigger
is pulled and when the picture is taken. During the delay time, the aiming light
will appear, but the LEDs won’t turn on until the delay time is over.
200 milliseconds
400 milliseconds
* Off (no delay)
2 - 18
IMAGETEAM™ 4410/4710 User’s Guide
Aimer Interval
Aimer Interval turns off the aiming light, or programs the aimer to come on at
certain intervals when reading symbols with the scanner. You may program the
scanner to use the aimer Every Read, Every Second Read, or Every Third
Read. You may also program the scanner to use the aimer every “x” reads, by
entering a number from 0 to 999 to indicate “x.”
Off
* Every Read
Every Third Read
Every Second Read
Every “x” Reads ‡
Note: ‡
A one- to three digit number and Save are
required after reading this programming symbol. Refer to the
Programming Chart (inside back cover).
IMAGETEAM™ 4410/4710 User’s Guide
2 - 19
Centering
Use the centering feature to narrow the imager’s field of view to make sure that
the imager reads only those bar codes intended by the user. For instance, if
multiple codes are placed closely together, centering will insure that only the
desired codes are read. When centering is turned on, the imager only reads
codes that intersect the centering window set up by the user. The centering
window must intersect the center of the image. If a bar code is not within the
predefined window, it will not be decoded or output by the scanner.
If centering is turned on by scanning the On bar code below, the default centering
window is a 60 pixel square area in the center of the imager’s field of view. The
position of the window may be changed by scanning the top, bottom, left, and
right centering bar codes that follow and the appropriate pixel value, if other than
the default, from the Programming Chart in the back of this manual. The defaults
are listed in the table below.
Window Position
Default
Minimum
Maximum
Serial Command
Top of centering
window
210
000
239
DECTPYxxx
Bottom of centering window
270
240
479
DECBTYxxx
Left of centering
window
290
0
319
DECTPXxxx
Right of centering
window
350
320
639
DECBTXxxx
The centering function can be used in conjunction with the Aimer Delay feature
(page 2-18) for the most error-free operation in applications where multiple
codes are spaced closely together. Using the Aimer Delay and Centering
features, the imager can emulate the operation of older systems, such as linear
laser bar code scanners.
On
* Off
The figure below illustrates the default top, bottom, left, and right pixel positions.
The position of the pixels is measured from the top and the left side of the
2 - 20
IMAGETEAM™ 4410/4710 User’s Guide
imager’s field of view with the field of view being 640 by 480 pixels.
290
350
0
640
Top
210
Bottom
Default
Center
270
Left
Right
480
IMAGETEAM™ 4410/4710 User’s Guide
2 - 21
Top of Centering
Window
Top of Centering Window
Default (210)
Bottom of Centering
Window
Bottom of Centering
Window Default (270)
Left of Centering
Window
Right of Centering
Window
2 - 22
Left of Centering
Window Default (290)
Right of Centering
Window Default (350)
IMAGETEAM™ 4410/4710 User’s Guide
In the example below, the gray area is the full imager field of view and the white
area is the centering window. Bar Code 1 will not be read, while Bar Code 2 will
be.
Bar Code 1
Bar Code 2
AutoTrigger
Two AutoTrigger Modes are available: Scan Stand and Presentation Mode.
When a unit is in Scan Stand mode, it remains idle as long as it sees the Scan
Stand symbol. (See Scan Stand Symbol that follows.) When a different code is
presented, the Imager is triggered to read the new code.
Note: The scanner automatically adjusts the illumination LEDs to the lowest
light level possible to maintain a good lock on the Scan Stand symbol.
Presentation mode is for those applications where a scan stand will not work, i.e.,
when large packages must be scanned. To program the device for presentation
mode, refer to "Presentation Mode" on page 2-24.
Scan Stand
This selection programs the Imager to work in a Scan Stand.
* Off
IMAGETEAM™ 4410/4710 User’s Guide
On
2 - 23
Scan Stand Symbol
Note: Scan Stand mode does not work when scanner is programmed for the
HHLC interface.
When a unit is in Scan Stand mode, the LEDs shine at the Scan Stand symbol
on the base of the stand which tells it to remain idle. When the Scan Stand
symbol is covered, the imager turns the LEDs on at the configured power level
(Default High) and attempts to find and decode bar codes in its field of view.
Scan Stand
Symbol
Presentation Mode
Note: Presentation Mode does not work when scanner is programmed for the
HHLC interface.
This programs the scanner to work in Presentation Mode.
* Off
On
Presentation Re-trigger Delay
This sets the time period before the scanner can re-trigger for another read
attempt. Setting a re-trigger delay protects against accidental rereads of the
same bar code. Longer delays are effective in minimizing accidental rereads at
POS (point of sale). Use shorter delays in applications where repetitive bar code
scanning is required. Entries are in milliseconds, from 1 to 10,000. Scan the
Presentation Re-trigger Delay bar code below, then scan the number of
milliseconds and the Save bar code from the inside back cover.
Default = 200.
Presentation Re-trigger Delay
2 - 24
IMAGETEAM™ 4410/4710 User’s Guide
Presentation Lights
When using the scanner in presentation mode, the illuminating LEDs can be
programmed on or off. If there is sufficient ambient light, the LEDs can be turned
off by scanning the Lights Off bar code below. When a bar code is presented to
the scanner, the illuminating LEDs turn on to scan the bar code and then turn off
when the bar code has been read. Default = Presentation Mode Lights On.
* On
Off
Presentation Default
Defaults all presentation mode settings. Defaults = Presentation Mode Off,
Presentation Reread Delay 200 ms.
Presentation Default
IMAGETEAM™ 4410/4710 User’s Guide
2 - 25
Fast Omni Mode
Normally, the imager searches throughout its whole field of view to determine if
a bar code is present. Fast omni-directional mode provides a reduced search
pattern that increases the scan rate of the imager. When fast omni mode is
enabled, the imager only tries to locate bar codes in the center area of the image.
Consequently, the user is required to center the aiming line over the bar code he
wants to read. When a portion of the bar code is in the center area of the image,
the imager locates and decodes the bar code. The entire bar code does not need
to be in the center area, only a portion of it. Bar codes that are not in the center
area of the image will not be found.
Note: Fast Omni Mode is not recommended when scanning Data Matrix codes.
* Normal, Full
Search Mode
Reduced Omnidirectional Mode
Beeper Volume
2 - 26
Off
Low
Medium
* High
IMAGETEAM™ 4410/4710 User’s Guide
Power Up Beeper
* On
Off
Output Sequence Beeper
If you are using an Output Sequence (see "Output Sequence Overview" on page
2-43), you may want to hear a beep after each bar code as it is read. Scan
Output Sequence Beeper On to enable this feature, or Off to disable it.
Off
* On
Beep On Decode
If you want the scanner to beep each time it reads a bar code, leave this setting
On. If you don’t want it to beep on each read, but do want it to beep for other
events, such as error conditions, set this selection to Off.
Off
* On
Beeper Default
Defaults all beeper settings. Defaults = Beeper Volume High, Power Up Beeper
On, Output Sequence Beeper On, Beep On Read On.
Beeper Default
IMAGETEAM™ 4410/4710 User’s Guide
2 - 27
Intercharacter, Interfunction,
and Intermessage Delays
Some terminals drop information (characters) if data comes through too quickly.
Intercharacter, interfunction, and intermessage delays slow the transmission of
data increasing data integrity.
Each delay is composed of a 5 millisecond step. You can program up to 99 steps
(of 5 ms each).
Intercharacter Delay
Note: This selection is valid for keyboard wedge interfaces only.
This is a delay of up to 495 milliseconds (in multiples of 5) placed between the
transmission of each character of scanned data. You can program up to 99 steps
(of 5 ms each). Scan the Intercharacter Delay bar code below, then scan the
number of steps, and the Save bar code from the inside back cover.
Note: If you make an error while scanning the digits (before scanning Save),
scan Discard on the back cover and scan the correct digits and Save
again.
Prefix
Scanned Data
1
2
3
4
Suffix
5
Intercharacter Delay
Intercharacter Delay
To remove this delay, scan the Intercharacter Delay bar code, then set the
number of steps to 00. Scan the Save bar code from the inside back cover.
User Specified Intercharacter Delay
Note: This selection is valid for keyboard wedge interfaces only.
This is a delay of up to 495 milliseconds (in multiples of 5) placed after the
transmission of a particular character of scanned data. You can program up to
99 steps (of 5 ms each) to follow the character you specify. Scan the Delay
Length bar code below, then scan the number of steps for the delay, and the
Save bar code from the inside back cover.
2 - 28
IMAGETEAM™ 4410/4710 User’s Guide
Next, scan the Character to Trigger bar code, then the 2 digit hex value for the
ASCII character that trigger the delay (refer to the "Decimal to Hex to
ASCII Conversion Chart" on page 2-36).Note:If you make an error while
scanning the digits (before scanning Save), scan Discard on the back
cover and scan the correct digits and Save again.
Delay Length
Character to Trigger Delay
To remove this delay, scan the Delay Length bar code, then set the number of
steps to 00. Scan the Save bar code from the inside back cover.
Interfunction Delay
Note: This selection is valid for keyboard wedge interfaces only.
This is a delay of up to 495 milliseconds (in multiples of 5) placed between the
transmission of each segment of the message string. You can program up to 99
steps (of 5 ms each). Scan the Interfunction Delay bar code below, then scan
the number of steps, and the Save bar code from the inside back cover.
Note: If you make an error while scanning the digits (before scanning Save),
scan Discard on the back cover and scan the correct digits and Save
again.
Prefix
STX
1
Scanned Data
HT
2 3 4 5
Suffix
CR
LF
Interfunction Delays
Interfunction Delay
To remove this delay, scan the Interfunction Delay bar code, then set the
number of steps to 00. Scan the Save bar code from the inside back cover.
IMAGETEAM™ 4410/4710 User’s Guide
2 - 29
Intermessage Delay
Note: This selection is valid for keyboard wedge interfaces only.
This is a delay of up to 495 milliseconds (in multiples of 5) placed between each
scan transmission. You can program up to 99 steps (of 5 ms each). Scan the
Intermessage Delay bar code below, then scan the number of steps, and the
Save bar code from the inside back cover.
Note: If you make an error while scanning the digits (before scanning Save),
scan Discard on the back cover and scan the correct digits and Save
again.
1st Scan Transmission
2nd Scan Transmission
Intermessage Delay
Intermessage Delay
To remove this delay, scan the Intermessage Delay bar code, then set the
number of steps to 00. Scan the Save bar code from the inside back cover.
2 - 30
IMAGETEAM™ 4410/4710 User’s Guide
Prefix/Suffix Overview
When a bar code is scanned, additional information is sent to the host computer
along with the bar code data. This group of bar code data and additional,
user-defined data is called a “message string.” The selections in this section are
used to build the user-defined data into the message string.
Prefix and Suffix characters are data characters that can be sent before and after
scanned data. You can specify if they should be sent with all symbologies, or
only with specific symbologies. The following illustration shows the breakdown
of a message string:
Prefix
1-10
alpha
numeric
characters
Scanned Data
variable
length
Suffix
1-10
alpha
numeric
characters
Points to Keep In Mind
• It is not necessary to build a message string. The selections in this chapter
are only used if you wish to alter the default settings. Default prefix = None.
Default suffix = CR/LF.
• A prefix or suffix may be added or cleared from one symbology or all
symbologies.
• You can add any prefix or suffix from the "Decimal to Hex to ASCII
Conversion Chart" on page 2-36, plus Code I.D. and Aim I.D.
• You can string together several entries for several symbologies at one time.
• Enter prefixes and suffixes in the order in which you want them to appear on
the output.
IMAGETEAM™ 4410/4710 User’s Guide
2 - 31
Adding a Prefix or Suffix
1. Scan the Add Prefix (page 2-34) or Add Suffix symbol (page 2-34).
2. Determine the 2 digit Hex value from the "Symbology Chart" on page 2-35
for the symbology to which you want to apply the prefix or suffix.
3. Scan the 2 hex digits from the Programming Chart inside the back cover or
scan 9, 9 for all symbologies.
4. Determine the hex value from the "Decimal to Hex to ASCII Conversion
Chart" on page 2-36 for the prefix or suffix you wish to enter.
5. Scan the 2 digit hex value from the Programming Chart inside the back
cover.
Note: Repeat Steps 4 and 5 for every prefix or suffix character.
Note: To add the Code I.D., scan 5, C, 8, 0.
To add AIM I.D., scan 5, C, 8, 1.
To add a backslash (\), scan 5, C, 5, C.
6. Scan Save to exit and save, or scan Discard to exit without saving.
Repeat Steps 1-6 to add a prefix or suffix for another symbology.
Example: Add a Suffix to a specific symbology
To send a CR (carriage return)Suffix for UPC only:
1. Scan Add Suffix.
2. Determine the 2 digit hex value from the "Symbology Chart" on page 2-35 for
UPC.
3. Scan 6, 3 from the Programming Chart (inside back cover).
4. Determine the hex value from the "Decimal to Hex to ASCII Conversion
Chart" on page 2-36 for the CR (carriage return).
5. Scan 0, D from the Programming Chart (inside back cover).
6. Scan Save, or scan Discard to exit without saving.
Clearing One or All Prefixes or Suffixes
You can clear a single prefix or suffix, or clear all prefixes/suffixes for a
symbology. When you Clear One Prefix (Suffix), the specific character you
select is deleted from the symbology you want. When you Clear All Prefixes
(Suffixes), all the prefixes or suffixes for a symbology are deleted.
1. Scan the Clear One Prefix symbol.
2. Determine the 2 digit Hex value from the "Symbology Chart" on page 2-35
for the symbology from which you want to clear the prefix or suffix.
3. Scan the 2 digit hex value from the Programming Chart inside the back cover
or scan 9, 9 for all symbologies.
Your change is automatically saved.
2 - 32
IMAGETEAM™ 4410/4710 User’s Guide
Add a Carriage Return Suffix to All Symbologies
Scan the following bar code if you wish to add a Carriage Return/Line Feed Suffix
to all symbologies at once. This action first clears all current suffixes, then
programs a carriage return suffix for all symbologies.
Add CR/LF Suffix
All Symbologies
Add a Code I.D. Prefix to All Symbologies
This selection allows you to turn on (or off) transmission of a Code I.D. before the
decoded symbology. (See the "Symbology Chart" on page 2-35 for the single
character code that identifies each symbology.) This action first clears all current
prefixes, then programs a Code I.D. prefix for all symbologies.
Add Code ID Prefix
All Symbologies
Add an AIM I.D. Prefix to All Symbologies
This selection allows you to turn on (or off) transmission of an AIM I.D. before the
decoded symbology. (See the "Symbology Chart" on page 2-35 for the single
character code that identifies each symbology.) This action first clears all current
prefixes, then programs an AIM I.D. prefix for all symbologies.
Add AIM ID Prefix
All Symbologies
(See AIM Guidelines on Symbology Identifiers for more information on the AIM
symbology ID characters.)
IMAGETEAM™ 4410/4710 User’s Guide
2 - 33
Prefix Entries
Clear One Prefix †
Add Prefix †
Clear All Prefixes
Suffix Entries
Add Suffix †
Clear One
Suffix †
Clear All Suffixes
† One or more two digit numbers and Save are required after reading this
programming symbol. Refer to the Programming Chart (inside back cover).
Exit Selections
Save
2 - 34
Discard
IMAGETEAM™ 4410/4710 User’s Guide
Symbology Chart
Symbology
Code AIM Hex
ID
ID
ID
Symbology
Code AIM
ID
ID
Hex
ID
Australian 4 State
A
]X
41
Interleaved 2 of 5
e
]l
65
Aztec Code
z
]z
7A
Japanese Postal
J
]X
4A
BC412**
g
]X
67
Kix (Dutch) Postal
K
]X
4B
BPO 4 State
B
]X
42
Maxicode
x
]U
78
Canadian 4 State
C
]X
43
Micro PDF417
R
]L
52
Codabar
a
]F
61
MSI
g
]M0
67
Codablock-F
q
]O
71
No Read
Code 11
h
]H0
68
OCR
o
]Y
6F
Code 39
b
]A
62
PDF417
r
]L
72
Code 49
l
]T
6C
Planet Code
L
]X
4C
Code 93
i
]G
69
Postnet
P
]X
50
Code 128
j
]C
6A
QR Code
s
]Q
73
Code Z**
u
]X
75
RSS/Composites
y
]e
79
Data Matrix
w
]d
77
UPC
c
]E
63
EAN
d
]E
64
Vericode**
v
]V
IATA 2 of 5
f
]R
66
All Symbologies †
9C
76
99
Note: Prefix/Suffix entries for specific symbologies override the universal (All
Symbologies, 99) entry.
Note: † All Symbologies: Prefix/Suffix programming only!
Note: ** Not available in standard product. Only available when ordered in
custom firmware
IMAGETEAM™ 4410/4710 User’s Guide
2 - 35
Decimal to Hex to ASCII Conversion Chart
Dec.
Hex
ASCII
Dec.
Hex
ASCII
Dec.
Hex
ASCII
Dec.
Hex
ASCII
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
US
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
SP
!
“
#
$
%
&
‘
(
)
*
+
,
.
/
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
@
A
B
C
D
E
F
G
H
l
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
‘
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
DEL
2 - 36
IMAGETEAM™ 4410/4710 User’s Guide
Data Format Editor Overview
The Data Format Editor selections are used to edit scanned data. For example,
you can use the Data Format Editor to insert characters at certain points in bar
code data as it is scanned.
It is not necessary to use the Data Format Editor. A set of defaults for the data
format is already programmed in the scanner. The selections in the following
pages are used only if you wish to alter the default settings. Default Data Format
setting = none.
If you have changed data format settings, and wish to clear all formats and return
to the defaults, scan the Default Data Format code.
To Add a Data Format
1. Scan the Enter Data Format symbol (page 2-40).
2. Primary/Alternate Format
Determine if this will be your primary data format, or one of 3 alternate
formats. (Alternate formats allow you “single shot” capability to scan one bar
code using a different data format. After the one bar code has been read,
the scanner reverts to the primary data format. See "Alternate Data
Formats" on page 2-42.) If you are programming the primary format, scan 0.
If you are programming an alternate format, scan 1, 2, or 3, depending on
the alternate format you are programming.
3. Terminal Type
Refer to the "Supported Terminals Chart" on page 2-5 and locate the
Terminal ID number for your PC. Scan three numeric bar codes on the
inside back cover to program the scanner for your terminal ID (you must
enter 3 digits). For example, scan 0 0 3 for an AT wedge.
Note: The wildcard for all terminal types is 099.
4. Code I.D.
On page 2-35, find the symbology to which you want to apply the data
format. Locate the Hex value for that symbology and scan the 2 digit hex
value from the Programming Chart.
5. Length
Specify what length (up to 9999 characters) of data will be acceptable for this
symbology. Scan the four digit data length from the Programming Chart.
(Note: 50 characters is entered as 0050. 9999 is a universal number,
indicating all lengths.)
6. Editor Commands
Refer to the "Format Editor Commands" on page 2-38. Scan the symbols
that represent the command you want to enter. 94 alphanumeric characters
may be entered for each symbology data format.
7. Scan Save to save your entries.
IMAGETEAM™ 4410/4710 User’s Guide
2 - 37
Other Programming Selections
• Clear One Data Format
This deletes one data format for one symbology. If you are clearing the
primary format, scan 0. If you are clearing an alternate format, scan 1, 2, or
3, depending on the alternate format you are clearing. Scan the Terminal
Type (refer to the "Supported Terminals Chart" on page 2-5), Code I.D. and
the length of the format you want to delete. That length data format for that
symbology is deleted and all other formats are unaffected.
• Save
This exits, saving any Data Format changes.
• Discard
This exits without saving any Data Format changes.
Format Editor Commands
Send Commands
F1 Send all characters followed by “xx” key or function code, starting from
current cursor position. Syntax = F1xx (xx stands for the hex value for an
ASCII code, see "Decimal to Hex to ASCII Conversion Chart" on page 236.)
F2 Send “nn” characters followed by “xx” key or function code, starting from
current cursor position. Syntax = F2nnxx (nn stands for the numeric
value (00-99) for the number of characters and xx stands for the hex value
for an ASCII code. See "Decimal to Hex to ASCII Conversion Chart" on
page 2-36.)
F3 Send up to but not including “ss” character (Search and Send) starting
from current cursor position, leaving cursor pointing to “ss” character
followed by “xx” key or function code. Syntax = F3ssxx (ss and xx both
stand for the hex values for ASCII codes, see "Decimal to Hex to ASCII
Conversion Chart" on page 2-36.)
F4 Send “xx” character “nn” times (Insert) leaving cursor in current cursor
position. Syntax = F4xxnn (xx stands for the hex value for an ASCII code,
see "Decimal to Hex to ASCII Conversion Chart" on page 2-36, and nn is
the numeric value (00-99) for the number of times it should be sent.)
E9 Send all but the last “nn” characters, starting from the current cursor
position. Syntax = E9nn (nn is the numeric value (00-99) for the number
of characters that will not be sent at the end of the message.)
Move Commands
F5 Move the cursor ahead “nn” characters from current cursor position.
Syntax = F5nn (nn stands for the numeric value (00-99) for the number
of characters the cursor should be moved ahead.)
F6 Move the cursor back “nn” characters from current cursor position.
Syntax = F6nn (nn stands for the numeric value (00-99) for the number
of characters the cursor should be moved back.)
F7 Move the cursor to the beginning of the data string. Syntax = F7.
EA Move the cursor to the end of the data string. Syntax = EA
2 - 38
IMAGETEAM™ 4410/4710 User’s Guide
Search Commands
F8 Search ahead for “xx” character from current cursor position, leaving
cursor pointing to “xx” character. Syntax = F8xx (xx stands for the hex
value for an ASCII code, see "Decimal to Hex to ASCII Conversion
Chart" on page 2-36.)
F9 Search back for “xx” character from current cursor position, leaving cursor
pointing to “xx” character. Syntax = F9xx (xx stands for the hex value for
an ASCII code, see "Decimal to Hex to ASCII Conversion Chart" on page
2-36.)
E6 Search ahead for the first non “xx” character from the current cursor
position, leaving cursor pointing to non ”xx” character. Syntax = E6xx (xx
stands for the hex value for an ASCII code, see "Decimal to Hex to ASCII
Conversion Chart" on page 2-36.)
E7 Search back for the first non “xx” character from the current cursor
position, leaving cursor pointing to non ”xx” character. Syntax = E7xx (xx
stands for the hex value for an ASCII code, see "Decimal to Hex to ASCII
Conversion Chart" on page 2-36.)
Miscellaneous Commands
FB Suppress all occurrences of up to 15 different characters, starting at the
current cursor position, as the cursor is advanced by other commands.
When the FC command is encountered, the suppress function is
terminated. The cursor is not moved by the FB command. Syntax =
FBnnxxyy . .zz where nn is a count of the number suppress characters in
the list and xxyy .. zz is the list of characters to be suppressed. (xx stands
for the hex value for an ASCII code, see "Decimal to Hex to ASCII
Conversion Chart" on page 2-36.)
FC Disable suppress filter and clear all suppressed characters. Syntax = FC.
E4 Replaces up to 15 characters in the data string with user specified
characters. Replacement continues until the E5 command is
encountered. Syntax = E4nnxx1xx2yy1yy2...zz1zz2 where nn is the total
count of both characters to be replaced plus replacement characters; xx1
defines characters to be replaced and xx2 defines replacement
characters, continuing through zz1 and zz2.
E5 Terminates character replacement. Syntax = E5.
FE Compare character in current cursor position to the character “xx.” If
characters are equal, increment cursor. If characters are not equal, no
format match. Syntax = FExx (xx stands for the hex value for an ASCII
code, see "Decimal to Hex to ASCII Conversion Chart" on page 2-36.)
EC Check to make sure there is an ASCII number at the current cursor
position. If character is not numeric, format is aborted. Syntax = EC.
ED Check to make sure there is a non-numeric ASCII character at the current
cursor position. If character is numeric, format is aborted. Syntax = ED.
IMAGETEAM™ 4410/4710 User’s Guide
2 - 39
Data Format Editor
See page 2-37 through page 2-39 for a description of Data Format selections and
commands.
Enter Data Format †
Default
Data Format
(none)
Clear One
Data Format †
Clear All
Data Formats
Exit Selections
Save Current
Data Format Changes
Discard Current
Data Format Changes
† One or more two digit numbers and Save are required after reading this
programming symbol. Refer to the Programming Chart (inside back cover).
2 - 40
IMAGETEAM™ 4410/4710 User’s Guide
Data Formatter
When Data Formatter is turned off, the bar code data is output to the host as read
(including prefixes and suffixes).
* On/Not Required
Off
Require Data Format
When Data Formatter is Required, all input data must conform to an edited
format or the scanner does not transmit the input data to the host device.
Required
Show Data Formats
Read the Show Data Formats bar code to transmit the existing data formats.
One format per line is printed out.
Show Data Formats
IMAGETEAM™ 4410/4710 User’s Guide
2 - 41
Alternate Data Formats
Alternate formats allow you “single shot” capability to scan one bar code using a
different data format than your primary format. When data formats are
programmed (see page 2-37), you must input whether you are programming the
primary format, or an alternate format numbered 1, 2, or 3.
An alternate format is initiated by scanning one of the 3 alternate format bar
codes below. The scanner will scan the next bar code, formatting the data with
the selected alternate format, then revert immediately to the primary format.
Alternate
Data Format 1
Alternate
Data Format 2
Alternate Data Format 3
2 - 42
IMAGETEAM™ 4410/4710 User’s Guide
Output Sequence Overview
Output Sequence Editor
This programming selection allows you to program the Imager to output data
(when scanning more than one symbol) in whatever order your application
requires, regardless of the order in which the bar codes are scanned. Reading
the Default Sequence symbol programs the Imager to the Universal values,
shown below. These are the defaults. Be certain you want to delete or clear all
formats before you read the Default Sequence symbol.
Note: To make Output Sequence Editor selections, you’ll need to know the code
I.D., code length, and character match(es) your application requires. Use
the Alphanumeric symbols (inside back cover) to read these options.
To Add an Output Sequence
1. Scan the Enter Sequence symbol (see "Output Sequence Editor" on page
2-46).
2. Code I.D.
On the "Symbology Chart" on page 2-35, find the symbology to which you
want to apply the output sequence format. Locate the Hex value for that
symbology and scan the 2 digit hex value from the Programming Chart
(inside back cover).
3. Length
Specify what length (up to 9999 characters) of data output will be acceptable
for this symbology. Scan the four digit data length from the Programming
Chart. (Note: 50 characters is entered as 0050. 9999 is a universal number, indicating all lengths.)
4. Character Match Sequences
On the "Decimal to Hex to ASCII Conversion Chart" on page 2-36, find the
Hex value that represents the character(s) you want to match. Use the Programming Chart to read the alphanumeric combination that represents the
ASCII characters. (99 is the Universal number, indicating all characters.)
5. End Output Sequence Editor
Scan F F to enter an Output Sequence for an additional symbology, or Save
Current Output Sequence Changes to save your entries.
Other Programming Selections
• Discard Current Output Sequence Changes
This exits without saving any Output Sequence changes.
Output Sequence Example
In this example, you are scanning Code 93, Code 128, and Code 39 bar codes,
but you want the scanner to output Code 39 1st, Code 128 2nd, and Code 93
3rd, as shown below.
IMAGETEAM™ 4410/4710 User’s Guide
2 - 43
Note: Code 93 must be enabled to use this example.
A - Code 39
B - Code 128
C - Code 93
You would set up the sequence editor with the following command line:
SEQBLK62999941FF6A999942FF69999943FF
The breakdown of the command line is shown below:
SEQBLKsequence editor start command
62 code identifier for Code 39
9999 code length that must match for Code 39, 9999 = all lengths
41 start character match for Code 39, 41h = “A”
FF termination string for first code
6A code identifier for Code 128
9999 code length that must match for Code 128, 9999 = all lengths
42 start character match for Code 128, 42h = “B”
FF termination string for second code
69 code identifier for Code 93
9999 code length that must match for Code 93, 9999 = all lengths
43 start character match for Code 93, 43h = “C”
FF termination string for third code
Require Output Sequence
When an output sequence is Required, all output data must conform to an edited
sequence or the scanner will not transmit the output data to the host device.
When it’s On/Not Required, the scanner will attempt to get the output data to
conform to an edited sequence, but if it cannot, the scanner transmits all output
data to the host device as is.
2 - 44
IMAGETEAM™ 4410/4710 User’s Guide
When the output sequence is Off, the bar code data is output to the host as the
scanner decodes it.
Note: This selection is unavailable when the Multiple Symbols Selection is
turned on.
Required
On/Not Required
Off
IMAGETEAM™ 4410/4710 User’s Guide
2 - 45
Output Sequence Editor
Enter Sequence †
Default Sequence
Exit Selections
Save Current
Output Sequence Changes
Discard Current
Output Sequence Changes
Note: If you want the scanner to beep after each bar code is read, please see
"Output Sequence Beeper" on page 2-27.
† One or more two digit numbers and Save are required after reading this
programming symbol. Refer to the Programming Chart (inside back cover).
2 - 46
IMAGETEAM™ 4410/4710 User’s Guide
Multiple Symbols
Note: This feature does not work when the Imager is in Low Power mode.
When this programming selection is turned On, it allows you to read multiple
symbols with a single pull of the Imager’s trigger. If you press and hold the
trigger, aiming the Imager at a series of symbols, it reads unique symbols once,
beeping (if turned on) for each read. Data is output as the imager finds and
decodes the symbols. The imager attempts to find and decode new symbols as
long as the trigger is pulled. When this programming selection is turned Off, the
Imager will only read the symbol closest to the aiming beam.
On
* Off
No Read
With No Read turned On, the Imager notifies you if a code cannot be read. In
the Quick*View Scan Data Window (see "Scan Data Window" on page 7-4), an
“NR” appears when a code cannot be read. If No Read is turned Off, the “NR”
will not appear.
On
* Off
If you want a different notation than “NR,” for example, “Error,” or “Bad Code,”
you can edit the output message using the Data Formatter (see page 2-37). The
hex code for the No Read symbol is 9C.
IMAGETEAM™ 4410/4710 User’s Guide
2 - 47
Print Weight
Print Weight is used to adjust the way the scanner reads Matrix symbols. If a
scanner will be seeing consistently heavily printed matrix symbols, then a print
weight of 6 may improve the reading performance. For consistently light printing,
a print weight of 2 may help. A value from 0 to 7 may be used to adjust the print
weight. The default print weight is 4.
† Set Print Weight
* Default
† A one digit number from 1 to 7 is required after reading this programming
symbol. Refer to the Programming Chart (inside back cover).
Function Code Transmit
When this selection is enabled and function codes are contained within the
scanned data, the scanner transmits the function code to the terminal. Charts of
these function codes are provided in Chapter 9, Supported Interface Keys.
When the scanner is in keyboard wedge mode, the scan code is converted to a
key code before it is transmitted.
* On
2 - 48
Off
IMAGETEAM™ 4410/4710 User’s Guide
Video Reverse
Video Reverse is used to allow the imager to read bar codes that are inverted.
The “Off” bar code below is an example of this type of bar code. If additional
menuing is required, Video Reverse must be disabled to read the menu bar
codes and then re-enabled after menuing is completed.
Note: Images downloaded from the unit will not be reversed. This is a setting
for decoding only.
On
* Off
IMAGETEAM™ 4410/4710 User’s Guide
2 - 49
2 - 50
IMAGETEAM™ 4410/4710 User’s Guide
3
Symbologies
Introduction
Use this section to program the hand-held Imager.
This programming section contains the following menuing selections:
•
•
•
•
•
Linear Symbology Selections
Stacked Symbology Selections
Postal Symbology Selections
2D Matrix Symbology Selections
Diagnostics
IMAGETEAM™ 4410/4710 User’s Guide
3-1
Linear Symbologies
Codabar
<Default All Codabar Settings>
Codabar
* On
Off
Start/Stop Characters
Start/Stop characters identify the leading and trailing ends of the bar code. You
may either transmit, or not transmit Start/Stop characters.
Start/Stop Transmit
* Don’t Transmit
Start/Stop
Message Length
The message length selection is used to set the valid reading length of the bar
code. If the data length of the scanned bar code doesn’t match the valid reading
length, the scanner will not read the symbol. You may wish to set the same value
for minimum and maximum length to force the scanner to read fixed length bar
code data. This helps reduce the chances of a misread.
3-2
IMAGETEAM™ 4410/4710 User’s Guide
Linear Symbologies
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.
Min. length = 09
Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15
Max. length = 15
Maximum
Message Length
Minimum
Message Length
The desired message length and Save must be input after reading this
programming symbol. Refer to the Programming Chart (inside back cover).
Codabar, continued
Check Character
No Check Character indicates that the scanner reads and transmits bar code
data with or without a check character.
When Check Character is set to Validate, But Don’t Transmit, the unit will only
read Codabar bar codes printed with a check character, but will not transmit the
check character with the scanned data.
When Check Character is set to Validate, And Transmit, the scanner will only
read Codabar bar codes printed with a check character, and will transmit this
character at the end of the scanned data.
* No Check Character
Validate,
But Don’t Transmit
IMAGETEAM™ 4410/4710 User’s Guide
Validate,
And Transmit
3-3
Linear Symbologies
Code 39
< Default All Code 39 Settings >
Code 39
* On
Off
Start/Stop Characters
Start/Stop characters identify the leading and trailing ends of the bar code. You
may either transmit, or not transmit Start/Stop characters.
Transmit
3-4
* Don’t Transmit
IMAGETEAM™ 4410/4710 User’s Guide
Linear Symbologies
Message Length
The message length selection is used to set the valid reading length of the bar
code. If the data length of the scanned bar code doesn’t match the valid reading
length, the scanner will not read the symbol. You may wish to set the same
value for minimum and maximum length to force the scanner to read fixed length
bar code data. This helps reduce the chances of a misread.
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.
Min. length = 09
Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15
Max. length = 15
Minimum
Message Length
Maximum
Message Length
The desired message length and Save must be input after reading this
programming symbol. Refer to the Programming Chart (inside back cover).
Code 39, continued
Full ASCII
If Full ASCII Code 39 decoding is turned on, certain character pairs within the
bar code symbol will be interpreted as a single character. For example: $V will
be decoded as the ASCII character SYN, and /C will be decoded as the ASCII
character #.
NUL %U
DLE $P
SP
SPACE 0
0
@
%V
P
P
‘
W
p
+P
SOH $A
DC1 $Q
!
/A
1
1
A
A
Q
Q
a
+A
q
+Q
STX $B
DC2 $R
“
/B
2
2
B
B
R
R
b
+B
r
+R
ETX $C
DC3 $S
#
/C
3
3
C
C
S
S
c
+C
s
+S
EOT $D
DC4 $T
$
/D
4
4
D
D
T
T
d
+D
t
+T
ENQ $E
NAK $U
%
/E
5
5
E
E
U
U
e
+E
u
+U
ACK $F
SYN $V
&
/F
6
6
F
F
V
V
f
+F
v
+V
BEL $G
ETB $W
‘
/G
7
7
G
G
W
W
g
+G
w
+W
BS
$H
CAN $X
(
/H
8
8
H
H
X
X
h
+H
x
+X
HT
$I
EM
$Y
)
/I
9
9
I
I
Y
Y
i
+I
y
+Y
LF
$J
SUB $Z
*
/J
:
/Z
J
J
Z
Z
j
+J
z
+Z
VT
$K
ESC %A
+
/K
;
%F
K
K
[
%K
k
+K
{
%P
FF
$L
FS
%B
,
/L
<
%G L
L
\
%L
l
+L
|
%Q
CR
$M
GS
%C
-
-
=
%H
M
M
]
%M m
+M
}
%R
SO
$N
RS
%D
.
.
>
%I
N
N
^
%N
n
+N
~
%S
SI
$O
US
%E
/
/O
?
%J
O
O
_
%O o
+O
DEL %T
IMAGETEAM™ 4410/4710 User’s Guide
3-5
Linear Symbologies
Character pairs /M and /N decode as a minus sign and period respectively.
Character pairs /P through /Y decode as 0 through 9.
Full ASCII On
* Full ASCII Off
Code 39, continued
Check Character
No Check Character indicates that the scanner reads and transmits bar code
data with or without a check character.
When Check Character is set to Validate, But Don’t Transmit, the unit will only
read Code 39 bar codes printed with a check character, but will not transmit the
check character with the scanned data.
When Check Character is set to Validate, And Transmit, the scanner will only
read Code 39 bar codes printed with a check character, and will transmit this
character at the end of the scanned data.will transmit this character at the end of
the scanned data.
* No Check Character
Validate,
But Don’t Transmit
3-6
Validate,
And Transmit
IMAGETEAM™ 4410/4710 User’s Guide
Linear Symbologies
Code 11
< Default All Code 11 Settings >
Code 11
On
* Off
Message Length
The message length selection is used to set the valid reading length of the bar
code. If the data length of the scanned bar code doesn’t match the valid reading
length, the scanner will not read the symbol. You may wish to set the same
value for minimum and maximum length to force the scanner to read fixed length
bar code data. This helps reduce the chances of a misread.
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.
Min. length = 09
Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15
Max. length = 15
Minimum
Message Length
Maximum
Message Length
The desired message length and Save must be input after reading this
programming symbol. Refer to the Programming Chart (inside back cover).
IMAGETEAM™ 4410/4710 User’s Guide
3-7
Linear Symbologies
Code 11, continued
Check Digits Required
This option sets whether 1 or 2 check digits are required with Code 11 bar codes.
One Check Digit
3-8
* Two Check Digits
IMAGETEAM™ 4410/4710 User’s Guide
Linear Symbologies
Interleaved 2 of 5
< Default All Interleaved 2 of 5 Settings >
Interleaved 2 of 5
* On
Off
Message Length
The message length selection is used to set the valid reading length of the bar
code. If the data length of the scanned bar code doesn’t match the valid reading
length, the scanner will not read the symbol. You may wish to set the same
value for minimum and maximum length to force the scanner to read fixed length
bar code data. This helps reduce the chances of a misread.
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.
Min. length = 09
Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15
Max. length = 15
Minimum
Message Length
Maximum
Message Length
The desired message length and Save must be input after reading this
programming symbol. Refer to the Programming Chart (inside back cover).
IMAGETEAM™ 4410/4710 User’s Guide
3-9
Linear Symbologies
Interleaved 2 of 5, continued
Check Digit
When Check Digit is set to Validate, But Don’t Transmit, the unit will only read
Interleaved 2 of 5 bar codes printed with a check digit, but will not transmit the
check digit with the scanned data.
When Check Digit is set to Validate, And Transmit, the scanner will only read
Interleaved 2 of 5 bar codes printed with a check digit, and will transmit this digit
at the end of the scanned data.
* No Check Digit
Validate,
But Don’t Transmit
3 - 10
Validate,
And Transmit
IMAGETEAM™ 4410/4710 User’s Guide
Linear Symbologies
IATA 2 of 5
< Default All IATA 2 of 5 Settings >
IATA 2 of 5
On
* Off
Message Length
The message length selection is used to set the valid reading length of the bar
code. If the data length of the scanned bar code doesn’t match the valid reading
length, the scanner will not read the symbol. You may wish to set the same
value for minimum and maximum length to force the scanner to read fixed length
bar code data. This helps reduce the chances of a misread.
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.
Min. length = 09
Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15
Max. length = 15
Minimum
Message Length
Maximum
Message Length
The desired message length and Save must be input after reading this
programming symbol. Refer to the Programming Chart (inside back cover).
IMAGETEAM™ 4410/4710 User’s Guide
3 - 11
Linear Symbologies
MSI
< Default All MSI Settings >
MSI
On
* Off
Message Length
The message length selection is used to set the valid reading length of the bar
code. If the data length of the scanned bar code doesn’t match the valid reading
length, the scanner will not read the symbol. You may wish to set the same value
for minimum and maximum length to force the scanner to read fixed length bar
code data. This helps reduce the chances of a misread.
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.
Min. length = 09
Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15
Max. length = 15
Minimum
Message Length
Maximum
Message Length
The desired message length and Save must be input after reading this
programming symbol. Refer to the Programming Chart (inside back cover).
3 - 12
IMAGETEAM™ 4410/4710 User’s Guide
Linear Symbologies
MSI, continued
Check Digit
This selection allows you to specify whether the check digit should be
transmitted at the end of the scanned data.
Transmit
Check Digit
IMAGETEAM™ 4410/4710 User’s Guide
* Don’t Transmit
Check Digit
3 - 13
Linear Symbologies
Code 93
< Default All Code 93 Settings >
Code 93
On
* Off
Message Length
The message length selection is used to set the valid reading length of the bar code.
If the data length of the scanned bar code doesn’t match the valid reading length, the
scanner will not read the symbol. You may wish to set the same value for minimum
and maximum length to force the scanner to read fixed length bar code data. This
helps reduce the chances of a misread.
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.
Min. length = 09
Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15
Max. length = 15
Minimum
Message Length
Maximum
Message Length
The desired message length and Save must be input after reading this
programming symbol. Refer to the Programming Chart (inside back cover).
3 - 14
IMAGETEAM™ 4410/4710 User’s Guide
Linear Symbologies
Code 128
< Default All Code 128 Settings >
Code 128
* On
Off
Message Length
The message length selection is used to set the valid reading length of the bar
code. If the data length of the scanned bar code doesn’t match the valid reading
length, the scanner will not read the symbol. You may wish to set the same
value for minimum and maximum length to force the scanner to read fixed length
bar code data. This helps reduce the chances of a misread.
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.
Min. length = 09
Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15
Max. length = 15
Minimum
Message Length
Maximum
Message Length
The desired message length and Save must be input after reading this
programming symbol. Refer to the Programming Chart (inside back cover).
IMAGETEAM™ 4410/4710 User’s Guide
3 - 15
Linear Symbologies
ISBT
Scan the On code below if you wish to decode ISBT bar codes. (ISBT codes are
a combination of multiple linear symbols used to mark blood bags.)
On
3 - 16
* Off
IMAGETEAM™ 4410/4710 User’s Guide
Linear Symbologies
EAN/JAN 8
< Default All EAN/JAN 8 Settings >
EAN/JAN 8
On
* Off
Check Digit
This selection allows you to specify whether the check digit should be
transmitted at the end of the scanned data.
Transmit
Check Digit
IMAGETEAM™ 4410/4710 User’s Guide
* Don’t Transmit
Check Digit
3 - 17
Linear Symbologies
EAN/JAN 8 Addenda
You can add 2 or 5 digits to the end of all scanned EAN/JAN 8 data.
2 Digit Addenda On
* 2 Digit
Addenda Off
5 Digit Addenda On
* 5 Digit
Addenda Off
EAN/JAN 8 Addenda Required
When Addenda Required is used, the scanner will only read EAN/JAN 8 bar
codes that have addenda.
Required
* Not Required
EAN/JAN 8 Addenda Separator
When this feature is On, there is a space between the data from the bar code and
the data from the addenda. When turned Off, there is no space.
Space
3 - 18
* No Space
IMAGETEAM™ 4410/4710 User’s Guide
Linear Symbologies
EAN/JAN 13
< Default all EAN/JAN 13 Settings >
EAN/JAN 13
* On
Off
Check Digit
This selection allows you to specify whether the check digit should be
transmitted at the end of the scanned data.
Transmit
Check Digit
IMAGETEAM™ 4410/4710 User’s Guide
* Don’t Transmit
Check Digit
3 - 19
Linear Symbologies
EAN/JAN 13 Addenda
You can add 2 or 5 digits to the end of all scanned EAN/JAN 13 data.
2 Digit Addenda On
* 2 Digit
Addenda Off
5 Digit Addenda On
* 5 Digit
Addenda Off
EAN/JAN 13 Addenda Required
When Addenda Required is used, the scanner will only read EAN/JAN 13 bar
codes that have addenda.
Required
* Not Required
EAN/JAN 13 Addenda Separator
When this feature is On, there is a space between the data from the bar code and
the data from the addenda. When turned Off, there is no space.
Space
3 - 20
* No Space
IMAGETEAM™ 4410/4710 User’s Guide
Linear Symbologies
UPC A
< Default All UPC A Settings >
UPC A
* On
Off
Check Digit
This selection allows you to specify whether the check digit should be
transmitted at the end of the scanned data.
Transmit
Check Digit
* Don’t Transmit
Check Digit
Number System
The numeric system digit of a UPC symbol is normally transmitted, but the unit
can be programmed so it will not transmit it.
* Transmit
Number System
IMAGETEAM™ 4410/4710 User’s Guide
Don’t Transmit
Number System
3 - 21
Linear Symbologies
UPC A Addenda
You can add 2 or 5 digits to the end of all scanned UPC A data.
2 Digit Addenda On
* 2 Digit
Addenda Off
5 Digit Addenda On
* 5 Digit
Addenda Off
UPC A Addenda Required
When Addenda Required is used, the scanner will only read UPC A bar codes
that have addenda.
Required
* Not Required
UPC A Addenda Separator
When this feature is On, there is a space between the data from the bar code and
the data from the addenda. When turned Off, there is no space.
Space
3 - 22
* No Space
IMAGETEAM™ 4410/4710 User’s Guide
Linear Symbologies
UPC E0
< Default All UPC E0 Settings >
UPC E0
Most UPC bar codes lead with the 0 number system. For these codes, use the
UPC E0 selection. If you need to read codes that lead with the 1 number system,
use the UPC E1 selection (see "UPC E1" on page 3-24).
UPC E0
On
* UPC E0
Off
Check Digit
This selection allows you to specify whether the check digit should be
transmitted at the end of the scanned data.
Transmit
Check Digit
* Don’t Transmit
Check Digit
Number System
The numeric system digit of a UPC symbol is normally transmitted, but the unit
can be programmed so it will not transmit it.
Transmit
Number System
IMAGETEAM™ 4410/4710 User’s Guide
* Don’t Transmit
Number System
3 - 23
Linear Symbologies
UPC E0, continued
Version E Expand
Version E Expand, expands the UPC-E code to the 12 digit, UPC-A format.
Expand
* Don’t Expand
UPC E1
Most UPC bar codes lead with the 0 number system. For these codes, use the
UPC E0 selection (see "UPC E0" on page 3-23). If you need to read codes that
lead with the 1 number system, use the UPC E1 selection.
UPC E1
On
* UPC E1
Off
UPC E0/E1 Addenda
You can add 2 or 5 digits to the end of all scanned UPC E0 and E1 data.
2 Digit Addenda On
* 2 Digit
Addenda Off
5 Digit Addenda On
* 5 Digit
Addenda Off
3 - 24
IMAGETEAM™ 4410/4710 User’s Guide
Linear Symbologies
UPC E0/E1 Addenda Required
When Addenda Required is used, the scanner will only read UPC E0 and E1
bar codes that have addenda.
Required
* Not Required
UPC E0/E1 Addenda Separator
When this feature is On, there is a space between the data from the bar code
and the data from the addenda. When turned Off, there is no space.
Space
IMAGETEAM™ 4410/4710 User’s Guide
* No Space
3 - 25
Linear Symbologies
RSS-14
< Default All RSS-14 Settings >
RSS-14
Reduced Space Symbology (RSS) is a family of linear bar codes which meets
restricted space requirements, while still providing full product identification.
RSS-14 On
* RSS-14
Off
RSS-14 Limited
< Default All RSS-14 Limited Settings >
RSS-14 Limited
RSS-14 Limited On
3 - 26
* RSS-14 Limited
Off
IMAGETEAM™ 4410/4710 User’s Guide
Linear Symbologies
RSS-14 Expanded
< Default All RSS-14 Expanded Settings >
RSS-14 Expanded
RSS Expanded On
* RSS Expanded
Off
Message Length
The message length selection is used to set the valid reading length of the bar
code. If the data length of the scanned bar code doesn’t match the valid reading
length, the scanner will not read the symbol. You may wish to set the same
value for minimum and maximum length to force the scanner to read fixed length
bar code data. This helps reduce the chances of a misread.
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.
Min. length = 09
Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15
Max. length = 15
Minimum
Message Length
Maximum
Message Length
The desired message length and Save must be input after reading this
programming symbol. Refer to the Programming Chart (inside back cover).
IMAGETEAM™ 4410/4710 User’s Guide
3 - 27
Stacked Symbologies
Codablock
< Default All Codablock Settings >
Codablock
On
* Off
Message Length
The message length selection is used to set the valid reading length of the bar
code. If the data length of the scanned bar code doesn’t match the valid reading
length, the scanner will not read the symbol. You may wish to set the same value
for minimum and maximum length to force the scanner to read fixed length bar
code data. This helps reduce the chances of a misread.
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.
Min. length = 09
Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15
Max. length = 15
Minimum
Message Length
Maximum
Message Length
The desired message length and Save must be input after reading this
programming symbol. Refer to the Programming Chart (inside back cover).
3 - 28
IMAGETEAM™ 4410/4710 User’s Guide
Stacked Symbologies
PDF417
< Default All PDF417 Settings >
PDF417
* On
Off
Message Length
The message length selection is used to set the valid reading length of the bar
code. If the data length of the scanned bar code doesn’t match the valid reading
length, the scanner will not read the symbol. You may wish to set the same
value for minimum and maximum length to force the scanner to read fixed length
bar code data. This helps reduce the chances of a misread.
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.
Min. length = 09
Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15
Max. length = 15
Minimum
Message Length
Maximum
Message Length
The desired message length and Save must be input after reading this
programming symbol. Refer to the Programming Chart (inside back cover).
IMAGETEAM™ 4410/4710 User’s Guide
3 - 29
Stacked Symbologies
MicroPDF417
< Default All MicroPDF417 Settings >
MicroPDF417
* On
Off
Message Length
The message length selection is used to set the valid reading length of the bar
code. If the data length of the scanned bar code doesn’t match the valid reading
length, the scanner will not read the symbol. You may wish to set the same value
for minimum and maximum length to force the scanner to read fixed length bar
code data. This helps reduce the chances of a misread.
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.
Min. length = 09
Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15
Max. length = 15
Minimum
Message Length
Maximum
Message Length
The desired message length and Save must be input after reading this
programming symbol. Refer to the Programming Chart (inside back cover).
3 - 30
IMAGETEAM™ 4410/4710 User’s Guide
Stacked Symbologies
Code 49
< Default All Code 49 Settings >
Code 49
On
* Off
Message Length
The message length selection is used to set the valid reading length of the bar
code. If the data length of the scanned bar code doesn’t match the valid reading
length, the scanner will not read the symbol. You may wish to set the same
value for minimum and maximum length to force the scanner to read fixed length
bar code data. This helps reduce the chances of a misread.
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.
Min. length = 09
Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15
Max. length = 15
Minimum
Message Length
Maximum
Message Length
The desired message length and Save must be input after reading this
programming symbol. Refer to the Programming Chart (inside back cover).
IMAGETEAM™ 4410/4710 User’s Guide
3 - 31
Stacked Symbologies
EAN•UCC Composite Codes
Linear codes are combined with a unique 2D composite component to form a
new class called EAN•UCC Composite symbology. EAN•UCC Composite
symbologies allow for the co-existence of symbologies already in use.
On
* Off
Message Length
The message length selection is used to set the valid reading length of the bar
code. If the data length of the scanned bar code doesn’t match the valid reading
length, the scanner will not read the symbol. You may wish to set the same value
for minimum and maximum length to force the scanner to read fixed length bar
code data. This helps reduce the chances of a misread.
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.
Min. length = 09
Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15
Max. length = 15
Minimum
Message Length
Maximum
Message Length
The desired message length and Save must be input after reading this
programming symbol. Refer to the Programming Chart (inside back cover).
3 - 32
IMAGETEAM™ 4410/4710 User’s Guide
Stacked Symbologies
TLC39
TLC39 stands for TCIF Linked Code 39 (where TCIF stands for
Telecommunications Industry Forum). This code is a composite code since it
has a Code 39 linear component and a MicroPDF417 stacked code component.
All bar code readers are capable of reading the Code 39 linear component. In
fact, the linear component may be decoded as Code 39 even if TLC39 is
disabled. The MicroPDF417 component can only be decoded if TLC39 is
enabled.
On
IMAGETEAM™ 4410/4710 User’s Guide
* Off
3 - 33
Postal Symbologies
Note: Note:
For best performance
when reading a postal symbology, all other postal symbologies should be
turned off.
U.S. Postal Service POSTNET Code
On
* Off
Check Digit
This selection allows you to specify whether the check digit should be transmitted
at the end of the scanned data.
Transmit
Check Digit
* Don’t Transmit
Check Digit
Planet Code
On
* Off
Check Digit
This selection allows you to specify whether the check digit should be transmitted
at the end of the scanned data.
Transmit
Check Digit
3 - 34
* Don’t Transmit
Check Digit
IMAGETEAM™ 4410/4710 User’s Guide
Postal Symbologies
British Post Office 4 State Code
On
* Off
Canadian 4 State Code
On
* Off
Dutch Postal Code
On
* Off
Australian 4 State Code
On
* Off
Japanese Postal Service
On
IMAGETEAM™ 4410/4710 User’s Guide
* Off
3 - 35
2D Matrix Symbologies
QR Code
< Default All QR Code Settings >
QR Code
On
* Off
Message Length
The message length selection is used to set the valid reading length of the bar
code. If the data length of the scanned bar code doesn’t match the valid reading
length, the scanner will not read the symbol. You may wish to set the same value
for minimum and maximum length to force the scanner to read fixed length bar
code data. This helps reduce the chances of a misread.
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.
Min. length = 09
Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15
Max. length = 15
Minimum
Message Length
Maximum
Message Length
The desired message length and Save must be input after reading this
programming symbol. Refer to the Programming Chart (inside back cover).
3 - 36
IMAGETEAM™ 4410/4710 User’s Guide
2D Matrix Symbologies
Data Matrix
< Default All Data Matrix Settings >
Data Matrix
* On
Off
Message Length
The message length selection is used to set the valid reading length of the bar
code. If the data length of the scanned bar code doesn’t match the valid reading
length, the scanner will not read the symbol. You may wish to set the same
value for minimum and maximum length to force the scanner to read fixed length
bar code data. This helps reduce the chances of a misread.
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.
Min. length = 09
Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15
Max. length = 15
Minimum
Message Length
Maximum
Message Length
The desired message length and Save must be input after reading this
programming symbol. Refer to the Programming Chart (inside back cover).
IMAGETEAM™ 4410/4710 User’s Guide
3 - 37
2D Matrix Symbologies
MaxiCode
< Default All MaxiCode Settings >
MaxiCode
On
* Off
Message Length
The message length selection is used to set the valid reading length of the bar
code. If the data length of the scanned bar code doesn’t match the valid reading
length, the scanner will not read the symbol. You may wish to set the same value
for minimum and maximum length to force the scanner to read fixed length bar
code data. This helps reduce the chances of a misread.
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.
Min. length = 09
Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15
Max. length = 15
Minimum
Message Length
Maximum
Message Length
The desired message length and Save must be input after reading this
programming symbol. Refer to the Programming Chart (inside back cover).
3 - 38
IMAGETEAM™ 4410/4710 User’s Guide
2D Matrix Symbologies
MaxiCode, continued
Structured Carrier Message Only
A MaxiCode is made up of a primary and secondary message. The primary
portion, also known as the “structured carrier message,” contains information of
primary importance, such as package destination. The secondary portion
contains less important data, such as package weight. If your application
requires only the primary data from MaxiCodes, turn Structured Carrier Message
Only On. Turn this feature on if you are trying to read a damaged Maxicode.
The scanner may be able to extract just the structured carrier message if the
center portion of the code is intact.
On
IMAGETEAM™ 4410/4710 User’s Guide
* Off
3 - 39
2D Matrix Symbologies
Aztec Code
< Default All Aztec Code Settings >
Aztec Code
* On
Off
Message Length
The message length selection is used to set the valid reading length of the bar
code. If the data length of the scanned bar code doesn’t match the valid reading
length, the scanner will not read the symbol. You may wish to set the same value
for minimum and maximum length to force the scanner to read fixed length bar
code data. This helps reduce the chances of a misread.
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.
Min. length = 09
Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15
Max. length = 15
Minimum
Message Length
Maximum
Message Length
A one- to two-digit number and Save are required after reading this programming
symbol. Refer to the Programming Chart (inside back cover).
3 - 40
IMAGETEAM™ 4410/4710 User’s Guide
Diagnostics
Test Menu
When you scan the Test Menu On code then scan a programming code in this
manual, the scanner displays the content of a programming code. The
programming function will still occur, but in addition, the content of that
programming code is output to the terminal. You may wish to use this feature in
conjunction with Quick*View (see page 7-1).
Note: Note: This feature should not be used during normal scanner operation.
Note:
On
* Off
2D PQA (Print Quality Assessment)
Two-dimensional Print Quality Assessment (2D PQA) is a feature of Hand Held
Products’s image readers where the data from the successful read of a 2D bar
code symbol is augmented with lines of text both identifying the symbol and also
reporting graded measurement parameters obtained from it.
To utilize 2D PQA, you need to have an IT4410/4710 with revision 1.91.2.18 or
higher. To see displayed results, Microsoft® Notepad, a word processor/editing
program, or Quick*View (see page 7-1) is recommended.
For additional information on interpreting your read results, please refer to the
Quick Check 2D Print Assessment User’s Guide.
IMAGETEAM™ 4410/4710 User’s Guide
3 - 41
3 - 42
IMAGETEAM™ 4410/4710 User’s Guide
4
OCR Programming
Introduction
Use this section to program the hand-held Imager to read machine readable
fonts used in optical character recognition (OCR). The IT4410 reads 6 to 60
point OCR typeface.
The IT4410/4710 will read the following fonts:
• OCR-A
0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ
()<>/\+-*$
• OCR-B
• U.S. Currency Serial Number (Money)
*
You can either select an OCR default, or create your own custom template for
the type of OCR format you intend to read. See "OCR" on page 4-2 for
programming codes that will enable your scanner to read OCR-A, OCR-B or U.S.
Currency fonts. See "Creating OCR Templates" on page 4-4 if you want to
create a custom “template,” or character string that defines the length and
content of OCR strings that will be read with your scanner.
IMAGETEAM™ 4410/4710 User’s Guide
4-1
OCR
Default All OCR Settings turns off all OCR capability in the scanner, so the
scanner will be able to scan linear, stacked, matrix, and composite bar codes, but
not OCR fonts. In addition, any OCR templates you have created are erased.
The 8 digit default templates are reinstated for any future use of the OCR On
codes listed below.
< Default All OCR Settings >
OCR
OCR-A On allows you to scan characters in the OCR-A font. The default setting
allows you to scan any 8 digit combination. If you have created an OCR
template, character combinations that fit the template can be scanned (see
"Creating an OCR Template" on page 4-4).
OCR-A On
OCR-B On allows you to scan characters in the OCR-B font. The default setting
allows you to scan any 8 digit combination. If you have created an OCR
template, character combinations that fit the template can be scanned (see
"Creating an OCR Template" on page 4-4).
OCR-B On
U.S. Currency On allows you to scan characters in the font used on U.S.
currency. The default setting allows you to scan any 8 digit combination. If you
have created an OCR template, character combinations that fit the template can
be scanned (see "Creating an OCR Template" on page 4-4).
U.S. Currency On
4-2
IMAGETEAM™ 4410/4710 User’s Guide
All OCR Off turns off all OCR capability in the scanner, so the scanner will be
able to scan linear, stacked, matrix, and composite bar codes, but not OCR fonts.
However, any OCR templates you have created will be retained in memory.
* All OCR Off
OCR Direction
This setting can be used to prevent misreads of character strings that could be
interpreted differently in different orientations when you know the orientation of
the characters that are being read in relation to the scanner (e.g., 80086996
could read as 80086996 or 96698008) This feature is generally used with a fixed
mount scanner. Scan the appropriate bar code to set the direction. Default =
Left-to-Right.
* Left-to-Right
Top-to-Bottom
Right-to-Left
Bottom-to-Top
IMAGETEAM™ 4410/4710 User’s Guide
4-3
Creating OCR Templates
You can create a custom “template,” or character string that defines the length
and content of OCR strings that will be read with your scanner. There are several
choices when creating a custom template for your application. You can create a
template for a single format, you can string together several formats, and you can
create a template for a user-defined variable. These choices are described in
detail below.
Creating an OCR Template
A single template allows you to program the scanner to read any combination of
characters in the order you specify. Refer to examples that follow the Template
Characters table below.
Template Characters
a
represents any alphanumeric character (digit or letter)
c
represents a check character position
d
represents any digit
e
represents any available OCR character
g
represents character from user-defined variable “g”
h
represents character from user-defined variable “h”
l
represents any uppercase letter
t
marks the start of a new template
r
multi row indicator
All other characters represent themselves. Spaces can be used.
To Add an OCR Template
1. Begin building the template.
Scan the Enter OCR Template symbol (page 4-9).
2. Scan the characters for the string.
Use the Template Characters chart above to determine what characters you
need to create your format. Use the OCR Programming Chart (after the
Sample Codes in the back of this manual) to scan the characters for your
template.
Example A: You need to read any combination of 8 digits. The template
would be:
dddddddd
4-4
IMAGETEAM™ 4410/4710 User’s Guide
To create this template, you would scan the Enter OCR Template symbol
(page 4-9), then scan the d from the OCR Programming Chart after the
Sample Codes in the back of this manual 8 times. Scan Save OCR Template
(page 4-9). This would let you read any string of 8 digits, for example:
37680981
3. Character Match Sequences
On the "Decimal to Hex to ASCII Conversion Chart" on page 2-36, find the
Hex value that represents the character(s) you want to match. Use the
Programming Chart (inside the back cover) to scan the numbers that
represent these characters.
Example B: You need to read 3 digits, 3 specific characters (ABC), 3 digits.
The template would be:
}
ddd414243ddd
hex codes for
letters A, B, and C
To create this template, you would scan the Enter OCR Template symbol
(page 4-9), scan the d from the OCR Programming Chart after the Sample
Codes in the back of this manual 3 times, scan 414243 from the Programming
Chart inside back cover (the hex characters for “A,” “B,” and “C”), then scan
the d from the inside back cover 3 more times. Scan Save OCR Template
(page 4-9). This would let you read any string of 3 digits, “ABC,” then any
string of 3 digits, for example:
551ABC983
4. Adding Spaces
You may also need to put spaces in your template.
Example C: You need to read 3 digits, space, 3 specific characters (ABC),
space, 3 digits. The template would be:
ddd2041424320ddd
hex code for a space
To create this template, you would scan the Enter OCR Template symbol
(page 4-9), scan the d from the OCR Programming Chart after the Sample
Codes in the back of this manual 3 times, scan 2041424320 from the
Programming Chart inside back cover (the hex characters for “space,” “A,”
“B,” “C,” “space”), then scan the d from the inside back cover 3 more times.
Scan Save OCR Template (page 4-9). This would let you read any string of
3 digits, space, “ABC,” space, then any string of 3 digits, for example:
551 ABC 983
IMAGETEAM™ 4410/4710 User’s Guide
4-5
Note: Note:
If using Quick*View to program, use the
space bar to designate a space and not the hex value of 20.
5. Exit OCR Template Editor
Scan Save OCR Template to save your entries. Discard OCR Template
exits without saving any OCR Template changes.
Stringing Together Multiple Formats
(Creating “Or” Statements)
You may want to program the scanner to accept many OCR formats. To do this,
you would string together each format with a “t.” This tells the scanner to read
optical characters that match any one of the formats in the template.
Example D: You need to read any combination of 8 digits, or a combination
of 4 digits, 2 uppercase letters, and 2 digits. The template would be:
ddddddddtddddlldd
To create this template, you would scan the Enter OCR Template symbol
(page 4-9), scan the d from the OCR Programming Chart after the Sample
Codes in the back of this manual 8 times, then scan the t to create the “or”
statement. Then you would scan the characters for the 2nd template. Scan
the d 4 times, scan l 2 times, then scan d 2 more times. Scan Save OCR
Template (page 4-9). This would let you read either type of format, for
example:
99028650
or
9902XZ50
You can string together as many templates as you need.
Creating a User-Defined Variable
You can create up to two of your own user variables for an OCR template. These
variables will represent any OCR readable characters. The user-defined
variables are stored under the letters “g” and “h.” Creating a user variable follows
the same steps as creating a template, but instead of scanning the Enter OCR
Template symbol, you scan the Enter User-Defined Variable symbol (page 49). The letters g and h can then be used in an OCR template to define the
variable you specified.
4-6
IMAGETEAM™ 4410/4710 User’s Guide
Example E: You need a variable to represent the letters “A,” “B,” or “C.” The
template for this variable would be:
414243
To create this template, you would scan the Enter User-Defined Variable g
symbol (page 4-9). Scan 414243 from the inside back cover (the hex
characters for “A,” “B,” and “C”). Scan Save OCR Template (page 4-9). This
will let you read either A or B or C in any position where you place the g. For
example, you could create the following template:
ddddddggg
This template would then let you read data that began with 6 digits, and had
an A, B, or C trailing. So you would be able to read:
654321ABC
or
654321BAC
or
654321CCC
Adding an OCR Check Character
You may want to program the scanner to read OCR strings that have a check
character. The IT4410/4710 reads and strips out the OCR check character
created using a modulo 10 or modulo 36 table. (Modulo 10 being digits 0-9,
modulo 36 being digits 0-9 and characters A-Z.)
Scan the Modulo 10 or Modulo 36 Check Character bar code to specify the
type of check character used in the OCR strings you’re scanning. The scanner
will then only read OCR character strings with a valid check character. The
IT4410/4710 transmits the OCR data without the check character data. You
must specify the location of the check character in the template with a c.
Example F: You need to read any combination of 6 digits, with a modulo 10
check character in the 7th position. The template would be:
ddddddc
To create this template, you would scan the Modulo 10 Check Character
symbol (page 4-9). Then scan the Enter OCR Template symbol, scan the d
from the inside back cover 6 times, and scan the c once. Scan Save OCR
Template (page 4-9). This template will let you read any combination of 6
digits with a correct check character after. (If the check character is invalid,
the scanner will issue an error beep.) For example, the following string could
be scanned:
0123455
and the output would be:012345
IMAGETEAM™ 4410/4710 User’s Guide
4-7
Reading Multi-Row OCR
The IT4410/4710 is capable of decoding multi-row OCR text. Consider the
following example. This example shows serial commands as would be entered
using Quick*View.
Example G: You need to read multiple rows of OCR data as shown below:
12345678
ABCDEFGH
To read the first row of OCR data, you would menu the following template:
OCRTMP"dddddddd".
This template is the default OCR template. If you wanted to read the second
line of data, you would use the following template:
OCRTMP"llllllll".
To read both lines of OCR at one time, use the variable r to indicate the start
of a new row. All of the other templating variables for the individual rows work
the same as previously described. For instance, in the above example, you
would use the following template to read both rows:
OCRTMP"ddddddddrllllllll".
To read the three rows below, you would use the template command
"OCRTMP"ddddddddrllllllllrlllldddd".
12345678
ABCDEFGH
ABCD1234
Note: Note: Reading more than three rows of OCR is not recommended.
Contact the factory if you have an application that requires reading 4 or
more rows of OCR.
4-8
IMAGETEAM™ 4410/4710 User’s Guide
OCR Template Codes
Enter OCR Template †
Enter UserDefined Variable
“g”†
Enter UserDefined Variable
“h”†
OCR Modulo 10
Check
Character
OCR Modulo 36
Check
Character
† One or more two-digit numbers and Save are required after reading this
programming symbol. Refer to the Programming Chart (inside back cover).
Exit Selections
Save OCR Template
Discard OCR Template
IMAGETEAM™ 4410/4710 User’s Guide
4-9
4 - 10
IMAGETEAM™ 4410/4710 User’s Guide
5
Default Charts
The following chart lists the factory default settings (indicated by a “✱” on the
programming menu pages).
Parameter
Default Setting
Page
Terminal ID - Keyboard Wedge
003
page 2-4
Terminal ID - True RS-232
000
page 2-4
Keyboard Country
0
page 2-6
Keyboard Style
Regular
page 2-7
Control + ASCII Off
page 2-8
Keyboard Modifiers
Turbo Mode Off
page 2-8
Numeric Keypad Off
page 2-8
Auto Direct Connect Off
page 2-8
Communication (RS-232) Selections
Parity
None
page 2-10
Baud Rate
38400
page 2-11
Word Length Data Bits
8
page 2-12
Word Length Stop Bits
1
page 2-12
Hardware Flow Control
Off
page 2-13
Software Flow Control
Off
page 2-13
Serial Triggering
On = 18, Off = 20
page 2-14
Trigger Timeout
60 seconds
page 2-15
Imager Selections
Power Saving Mode
Normal Power
page 2-16
Power Hold Mode
Off
page 2-17
LED Power Level
High
page 2-17
LED Flashing
On
page 2-18
Aimer Delay
Off (no delay)
page 2-18
Aimer Interval
Centering
Every Read
page 2-19
Off
page 2-20
Top of Centering Window = 210
page 2-22
Bottom of Centering Window = 270
page 2-22
Left of Centering Window = 290
page 2-22
Right of Centering Window = 350
page 2-22
Scan Stand
Off
page 2-23
Presentation Mode
Off
page 2-24
IMAGETEAM™ 4410/4710 User’s Guide
5-1
Parameter
Default Setting
Page
Presentation Re-Trigger Delay
200 ms
page 2-24
Presentation Lights
On
page 2-25
Beeper Volume
High
page 2-26
Power Up Beeper
On
page 2-27
Output Sequence Beeper
On
page 2-27
Beep On Decode
On
page 2-27
Intercharacter Delay
0
page 2-28
User Specified Intercharacter
Delay
0
page 2-28
Interfunction Delay
0
page 2-29
Intermessage Delay
0
page 2-30
Prefix/Suffix Selections
Prefix
None
page 2-34
Suffix
CR/LF
page 2-34
Data Formatter Selections
Data Format
None
Data Formatter
On
page 2-40
page 2-41
Require Data Format
Not Required
page 2-41
Output Sequence Selections
Multiple Symbols
Off
Require Output Sequence
Don’t Require
page 2-47
page 2-45
No Read
Off
page 2-47
Print Weight
4
page 2-48
Video Reverse
Off
page 2-49
Function Code Transmit
On
page 2-48
Linear Symbologies
Codabar
On
page 3-2
Start/Stop Characters
Don’t Transmit
page 3-2
Message Length
Min = 2, Max = 60
page 3-2
Check Character
No Check Character
page 3-3
Code 39
On
page 3-4
Start/Stop Characters
Don’t Transmit
page 3-4
Message Length
Min = 2, Max = 48
page 3-5
Full ASCII
Off
page 3-5
Check Character
No Check Character
page 3-6
5-2
IMAGETEAM™ 4410/4710 User’s Guide
Parameter
Default Setting
Page
Code 11
Off
page 3-7
Message Length
Min = 1, Max = 80
page 3-7
Check Digits Required
Two Check Digits
page 3-8
Interleaved 2 of 5
On
page 3-9
Message Length
Min = 4, Max = 80
page 3-9
Check Digit
No Check Character
page 3-10
IATA 2 of 5
Off
page 3-11
Message Length
Min = 4, Max = 80
page 3-11
MSI
Off
page 3-12
Message Length
Min = 4, Max = 48
page 3-12
Check Digit
Don’t Transmit
page 3-13
Code 93
Off
page 3-14
Message Length
Min = 0, Max = 80
page 3-14
Code 128
On
page 3-15
Message Length
Min = 0, Max = 80
page 3-15
ISBT
Off
page 3-16
page 3-17
EAN/JAN 8
Off
Check Digit
Don’t Transmit
page 3-17
EAN/JAN 8 Addenda
Off
page 3-18
EAN/JAN 8 Addenda Required
Off
page 3-18
EAN/JAN 8 Addenda Separator
No Space
page 3-18
EAN/JAN 13
On
page 3-19
Check Digit
Don’t Transmit
page 3-19
EAN/JAN 13 Addenda
Off
page 3-20
EAN/JAN 13 Addenda Required
Off
page 3-20
EAN/JAN 13 Addenda Separator
No Space
page 3-20
UPC A
On
page 3-21
Check Digit
Don’t Transmit
page 3-21
Number System
Transmit
page 3-21
UPC A Addenda
Off
page 3-22
UPC A Addenda Required
Off
page 3-22
UPC A Addenda Separator
No Space
page 3-22
UPC E0
Off
page 3-23
Check Digit
Don’t Transmit
page 3-23
Number System
Don’t Transmit
page 3-23
IMAGETEAM™ 4410/4710 User’s Guide
5-3
Parameter
Default Setting
Page
Version E Expand
Don’t Expand
page 3-24
UPC E1
Off
page 3-24
UPC E0/E1 Addenda
Off
page 3-24
UPC E0/E1 Addenda Required
Off
page 3-25
UPC E0/E1 Addenda Separator
No Space
page 3-25
page 3-26
RSS-14
Off
RSS-14 Limited
Off
page 3-26
RSS-14 Expanded
Off
page 3-27
RSS-14 Expanded
Message Length
Min = 1, Max = 80
page 3-27
Codablock
Off
page 3-28
Message Length
Min = 0, Max = 2048
page 3-28
PDF417
On
page 3-29
Message Length
Min = 1, Max = 2750
page 3-29
MicroPDF417
On
page 3-30
Message Length
Min = 1, Max = 2750
page 3-30
Code 49
Off
page 3-31
Message Length
Min = 1, Max = 81
page 3-31
EAN•UCC Composite
Codes
Off
page 3-32
Message Length
Min = 1, Max = 300
page 3-32
Postal Symbology Selections
POSTNET Code (USPS)
Off
page 3-34
Planet Code
Off
page 3-34
BPO 4 State Code
Off
page 3-35
Canadian 4 State Code
Off
page 3-35
Dutch Code
Off
page 3-35
Australian 4 State Code
Off
page 3-35
Japanese Postal Service
Off
page 3-35
2D Matrix Selections
QR Code
Off
page 3-36
Message Length
Min = 1, Max = 3500
page 3-36
Data Matrix
On
page 3-37
Message Length
Min = 1, Max = 1500
page 3-37
MaxiCode
Off
page 3-38
5-4
IMAGETEAM™ 4410/4710 User’s Guide
Parameter
Default Setting
Page
Message Length
Min = 1, Max = 150
page 3-38
SCM Only
Off
page 3-39
Aztec Code
On
page 3-40
Message Length
Min = 1, Max = 3750
page 3-40
OCR-A
Off
page 4-2
OCR-B
Off
page 4-2
U.S. Currency
Off
page 4-2
OCR Selections
IMAGETEAM™ 4410/4710 User’s Guide
5-5
5-6
IMAGETEAM™ 4410/4710 User’s Guide
6
Software Development Kit
Software Development Kit (SDK)
The IMAGETEAM™ Software Development Kit (SDK) provides a set of libraries,
tools, and sample source code to help software developers create an interface
between their host system and a Hand Held Products image/data capture
device. The SDK consists of:
• The API Definition and Documentation
• API Libraries
• Sample Code
Features of the SDK
• The SDK contains software libraries that interact with image/data capture
engines using a documented API (Application Programmers Interface).
• The image/data capture engine is easily integrated into a variety of host
platforms.
• The SDK captures images and saves them to standard .bmp file format.
Captured images can then be easily imported into a variety of common tools
and applications.
• Libraries are available for MS-DOS and 32-bit MS Windows®. This includes
Windows CE 2.x, Windows 95, 98, NT 4.0, and Win 2000. Additional libraries
can be created for custom embedded platforms upon request.
Refer to the Software Development Kit User’s Guide for complete information on
using the SDK.
IMAGETEAM™ 4410/4710 User’s Guide
6-1
6-2
IMAGETEAM™ 4410/4710 User’s Guide
7
Quick*View
Quick*View Demonstration Software Instructions
Quick*View is a Microsoft Windows® program that displays decoded symbol
messages and captures images (for instance, ID photographs) from the
IMAGETEAM 4410/4710 Imager. Bar code information and images are
displayed in the Quick*View window.
Setting Up the Imager and the Quick*View Software
1. Connect the Imager to the PC’s com port (com port 1 or com port 2) via the
appropriate interface cable (see "Unpacking the Imager" on page 1-2).Connect the appropriate power supply to the Imager. (The Imager cannot get its
power from the PC’s com port.)
For Microsoft Windows 95 or NT 4.0
2. Insert the Quick*View diskette labelled “32 Bit Release” into Drive A or B.
3. From the Start Menu, click on Run. Type “x:\setup” in the command line
box, where “x” represents a drive letter, typically “A” for the 3.5" floppy drive
on most PCs. Click on OK.
4. Follow the instructions in the setup screens.
5. To start the Quick*View program, from the Start Menu click on Programs,
Quickview, QuickView (32 Bit).
Installing Quick*View from the Web
1. Access the Hand Held Products web site at www.handheld.com.
2. Click in the Quick Search text box and enter Quick*View.
3. Click on Search Now.
4. Click on the entry for Quick*View.
5. When prompted, select Save File, and save the files to the
c:\windows\temp directory.
6. Once you have finished downloading the file, exit the web site.
7. Using Explorer, go to the c:\windows\temp file.
8. Double click on the Quickview.exe file. Follow the screen prompts to install
the Quick*View program.
9. To start Quick*View, from the Start Menu click on Programs, Quick*View,
Quick*View.
IMAGETEAM™ 4410/4710 User’s Guide
7-1
Note: f you wish, you can create a shortcut to the Quick*View executable on
your desktop.
Temporary Quick*View Configuration
For a quick download communication configuration, scan the Quick*View bar
code and the scanner will be temporarily configured for Quick*View settings.
Note: If you have a unit capable of keyboard wedge mode, scan the bar code
below and the unit will communicate in RS-232 mode, allowing it to work
with Quick*View. To convert the scanner back to keyboard wedge
communication, cycle the power.
Quick*View
7-2
IMAGETEAM™ 4410/4710 User’s Guide
Using the Quick*View Software
Upon startup, the Quick*View splash screen appears for approximately three
seconds. Quick*View will then attempt to establish communications with the
Imager.
If Communication Cannot Be Established
This message appears if communication cannot be established:
Quick*View defaults to com 1 as the communications port. If you have plugged
the Imager into another com port, you must Cancel out of this message.
Click on File - Preferences. This popup appears:
Click on the
radio button for
the appropriate
com port, then
click on OK.
Quick*View
should now be
able to locate
the Imager.
You may also need to pull the Imager’s trigger to establish communications
between the PC and the Imager.
If you want Quick*View to search for the Imager and establish communication,
click on Device - Auto Baud Detect.
IMAGETEAM™ 4410/4710 User’s Guide
7-3
Scan Data Window
Once successful communication has been established, you can scan codes and
display the bar code data in a window. Select View - Scan Data Window.
As you scan bar codes, the data appears in the Serial Scan Data Window.
You can alter the font in this window by using the Font button, or clear all data in
the window with the Clear button.
If you wish to see the mnemonic for any embedded control characters, you
should put a check in the checkbox for Expand Control Chars (the default
setting). If you wish to see the ASCII control character rather than the mnemonic,
turn off this checkbox.
Note: The ASCII control character that is displayed is dependent on the font you
are using.
7-4
IMAGETEAM™ 4410/4710 User’s Guide
Snapshot
You may also use the IMAGETEAM 4410/4710 to capture an image. Click on
Device - Snapshot, or click on the camera icon in the button bar to activate this
feature.
Resolution Snapshot
icons
icon
Select the resolution you wish to use for this image, either Full, Half or Quarter
Resolution. (These can also be selected by clicking on the 1, 1/2, or 1/4 buttons
in the button bar.)
Note: The higher resolution, the sharper the image, and the larger the size of
the resulting file. Higher resolution images also take longer to process.
You must also select whether you wish to capture the image in Gray Scale or in
Black & White.
Black & Gray Scale
White
Note: If you need to see exactly what the Imager sees (for example, if you are
diagnosing a bar code), you should set the image to Black & White.
If you want the Imager to display illuminated aiming brackets, click on Device Snapshot Properties - Use Aimer During Image Capture, or click on the aimer
icon in the button bar.
Aimer
icon
IMAGETEAM™ 4410/4710 User’s Guide
7-5
Snapshot, continued
Pull the Imager’s trigger to capture an image. Captured images appear in the
Quick*View window.
As you move the mouse over the image, the cursor changes to a magnifying
glass. Left click to zoom in to the image, right click to zoom out.
Saving an Image File
If you wish to save the file as a bitmap, click on File - Save As. Enter the location
and file name you wish to use for this file. Click on Save and a bitmap file will be
saved.
7-6
IMAGETEAM™ 4410/4710 User’s Guide
Open Com Port
If you wish to open a com port which does not have a device attached, you can
do so by selecting File - Open Com Port.
This dialog box appears:
Click on the arrows to select the Baud
Rate, Parity, and Data Bits for the
com port you wish to open. Click on
Open Port and Quick*View opens the
com port whether or not there is a
device attached. This feature may be
beneficial when troubleshooting a
device.
Reporting Firmware Revision
To find out what software version the Imager is using, click on Device - Report
Device Firmware Revision, or click on the Imager icon in the button bar.
Imager
icon
This popup lists the
firmware information:
IMAGETEAM™ 4410/4710 User’s Guide
7-7
Load New Imager Software
If you need to upgrade the Imager’s software, you can load a new software file
into the Imager’s ROM. Click on Device - Load Firmware File into ROM or click
on the lightning flash icon in the button bar.
Flash
icon
You will be
prompted for the
name of the hex file:
Select the hex file
and click on Open.
Quick*View will
flash the new
software into your
Imager’s ROM.
Imager Power Settings
By default, the Imager will power down after 2 minutes of inactivity. If you wish
to keep the Imager powered up indefinitely, click on Device - Hold Power. To
reset the Imager to the default power setting, click on Device - Remove Power
Hold.
Trigger Settings
If you wish to control the Imager’s trigger with the software, you can select
Device - Trigger On, or Device - Trigger Off. These settings turn the trigger on
and off just as if you were holding the trigger or releasing it manually. This
feature may be necessary when working with a fixed device that has no trigger.
7-8
IMAGETEAM™ 4410/4710 User’s Guide
RS-232 Serial Commands
Click on View - Serial Command Window to display the Command Center
window which allows you to enter serial commands to the Imager. Click on View
- Scan Data Window to open a window which displays serial data in a text
format.
Serial commands are used to program the Imager and to query the Imager about
programming parameters. The serial programming commands are listed
beginning on page 7-14. Information about performing queries is listed on page
page 7-11.
Serial Programming Commands
The serial programming commands can be used in place of the programming bar
codes listed in Chapter 3. Both the serial commands and the programming bar
codes will program the Imager. For complete descriptions and examples of each
programming command, refer to Chapter 3.
To enter a serial command, click in the Enter Menu Command text box and type
in the command(s) you wish to use. If you are typing in more than one command,
separate the commands with a semicolon (;). Click on Send Command to send
the command(s) to the Imager.
IMAGETEAM™ 4410/4710 User’s Guide
7-9
Responses
The Imager responds to serial commands with one of three responses:
ACK Indicates a good command which has been processed.
ENQ Indicates a bad command.
NAK Indicates the command was good, but the entry was out of the allowable
range, e.g., an entry for a minimum message length of 100 when the field
will only accept 2 characters.
Command Center Buttons
Display All Settings displays the settings currently
saved for the Imager.
Display Setting Ranges displays all the possible
serial commands and the allowable data field
parameters.
Display Firmware Rev displays the software version
being used by the Imager.
Build Command Bar Code is used to create an Aztec
code from a command or set of commands entered in
the Serial Window. (The size of the Aztec code can be
altered using the File - Preferences selection.) This
bar code can then be printed out and used to program
other Imagers.
Build Clone Bar Code is used to capture the settings from one Imager, and
input them to another Imager. When the Build Clone Bar Code button is clicked,
Quick*View captures the settings from the attached Imager and creates an Aztec
code which can be printed. (The size of the Aztec code can be altered using the
File - Preferences selection.) Any Imager that scans the resulting clone bar
code will be programmed to the same settings as the original Imager.
7 - 10
IMAGETEAM™ 4410/4710 User’s Guide
Query Commands
Several special characters can be used to query the Imager about its settings.
^
?
*
What is the default value for the setting(s).
What is the Imager’s current value for the setting(s).
What is the range of possible values for the setting(s). (The Imager’s
response uses a dash (-) to indicate a continuous range of values. A pipe (|)
separates items in a list of non-continuous values.)
Examples of Query Commands
Example #1:What is the range of possible values for Codabar Coding Enable?
Enter:
cbrena*.
Response: CBRENA0-1[ACK]
This response indicates that Codabar Coding Enable (CBRENA) has a range of
values from 0 to 1 (off and on).
Example #2: What is the default value for Codabar Coding Enable?
Enter:
cbrena^.
Response: CBRENA1[ACK]
This response indicates that the default setting for Codabar Coding Enable
(CBRENA) is 1, or on.
Example #3: What is the Imager’s current setting for Codabar Coding Enable?
Enter:
cbrena?.
Response: CBRENA1[ACK]
This response indicates that the Imager’s Codabar Coding Enable (CBRENA) is
set to 1, or on.
IMAGETEAM™ 4410/4710 User’s Guide
7 - 11
Example #4: What are the Imager’s settings for all Codabar selections?
Enter:
cbr?.
Response: CBRENA1[ACK],
CHK0[ACK],
CKX0[ACK],
SSX0[ACK],
MIN2[ACK],
MAX60[ACK],
DFT[ACK].
This response indicates that the Imager’s Codabar Coding Enable (CBRENA) is
set to 1, or on;
the Check Character (CHK and CKX) is set to 0, or No Check Character;
the Start/Stop Character is set to 0, or Don’t Transmit;
the Minimum Message Length (MIN) is 2 characters;
the Maximum Message Length (MAX) is 60 characters;
and the Default setting (DFT) has no value.
Trigger Commands
You can activate and deactivate the scanner with the serial trigger commands.
First, the scanner must be programmed for accepting serial commands by
scanning the Serial Triggering On bar code on page 2-14, or by sending the
serial command (TRGSER1.) on page 7-15. When the serial trigger factory
default settings are used and serial triggering is enabled, the trigger is activated
and deactivated by sending the following commands:
Activate
Deactivate
SYN T CR
SYN U CR
The scanner scans until a bar code has been read, until the deactivate command
is sent, or until the serial timeout has been reached. See "Trigger Timeout" on
page 2-15 for a description and the serial command on page 7-15.
7 - 12
IMAGETEAM™ 4410/4710 User’s Guide
Button Bar
The Quick*View button bar and the button functions are shown below.
Full HalfQuarter
Resolution
Capture gray scale image
Capture black & white image
Zoom out image
Zoom in image
Capture an image
Cancel image capture
Display Quick*View information
Display aimer
Print active file
Save file
Open file
Flash a hex file into ROM
Display firmware revision
Start Visual Menu software*
Note: *This icon only appears if you have Visual Menu software installed. Visual
Menu is available free of charge from the Hand Held Products website at
www.handheld.com.
IMAGETEAM™ 4410/4710 User’s Guide
7 - 13
Serial Programming Commands
Selection
Factory Default Settings
Setting
* Indicates Default Setting
Default
Serial Command
DEFALT.
Status Check
Show Software Revision
REV?.
Show Data Formats
DFMBK3?.
Enable All Symbologies
ALLENA1.
Disable All Symbologies
ALLENA0.
Output Selections
Power PC Revision
REVMPC.
Boot Code Revision
REV_BT.
Terminal ID
TERMID.
Keyboard Country
Keyboard Style
Keyboard Modifiers
KBDCTY.
Regular
KBDSTY0.
Caps Lock
KBDSTY1.
Shift Lock
KBDSTY2.
Emulate External
Keyboard
KBDSTY5.
Automatic Caps Lock
KBDSTY6.
*Control + ASCII Off
KBDCAS0.
Control + ASCII On
KBDCAS1.
*Turbo Mode Off
KBDTMD0.
Turbo Mode On
KBDTMD1.
*Numeric Keypad Off
KBDNPS0.
Numeric Keypad On
KBDNPS1.
*Auto Direct Conn. Off
KBDADC0.
Auto Direct Conn. On
KBDADC1.
Communication Settings
*Default All RS-232
Communication Settings
Parity
7 - 14
232DFT.
*None
232PARN.
Mark
232PARM.
Space
232PARS.
Odd
232PARO.
Even
232PARE.
IMAGETEAM™ 4410/4710 User’s Guide
Selection
Baud Rate
Word Length Data Bits
Word Length Stop Bits
Hardware Flow Control
Software Flow Control
Serial Triggering
Trigger Timeout
Hardware Triggering2
Setting
* Indicates Default Setting
Serial Command
*38400 BPS
232BDR38400.
300 BPS
232BDR300.
600 BPS
232BDR600.
1200 BPS
232BDR1200.
2400 BPS
232BDR2400.
4800 BPS
232BDR4800.
9600 BPS
232BDR9600.
19200 BPS
232BDR19200.
57600 BPS
232BDR57600.
115200 BPS
232BDR115200.
*8 Data Bits
232LEN8.
7 Data Bits
232LEN7.
*1 Stop Bit
232STP1.
2 Stop Bits
232STP2.
*Off
232CTS0.
On
232CTS1.
*Off
232SFL0.
On
232SFL1.
*Off
TRGSER0.
On
TRGSER1.
*Trigger Defaults
TRGDFT.
Set Trigger On value
1
TRG_ONXX.
Set Trigger Off value
1
TRGOFFXX.
Set Timeout
TRGSTO.
Trigger Mode
HWTRIG1.
Power Hold Mode
HWTRIG0.
*Normal Power
PWRDFT;
SCNLEDHIGH;
HSTSSS0.
Low Power
PWRTIM0;
SCNLEDLOW;
HSTSSS1.
Medium Power
PWRTIM10000;
SCNLEDHIGH;
HSTSSS0.
Imager Selections
Power Saving Mode
IMAGETEAM™ 4410/4710 User’s Guide
7 - 15
Selection
Power Hold Mode
LED Power
LED Flashing
Aimer Delay
Aimer Interval
Centering
Scan Stand
Presentation Mode
Presentation Re-Trigger Delay
Presentation Lights
Setting
* Indicates Default Setting
On
Serial Command
PWR_ON1.
*Off
PWR_ON0.
*High
SCNLEDHIGH.
Off
SCNLEDOFF.
Low
SCNLEDLOW.
*On
HSTLED0.
Off
HSTLED1.
*Off (no delay)
HSTAIM0.
200 milliseconds
HSTAIM200.
400 milliseconds
HSTAIM400.
*Every Read
HSTINT1.
Every 2nd Read
HSTINT2.
Every 3rd Read
HSTINT3.
Every “x” Read
HSTINT.
Off
HSTINT0.
On
DECWIN1.
*Off
DECWIN0.
Top of Centering Window
DECTPY.
Bottom of Centering Window
DECBTY.
Left of Centering Window
DECTPX.
Right of Centering Window
DECBTX.
*Off
SSTMOD0.
On
SSTMOD1.
On
PRSMOD1.
*Off
PRSMOD0.
*200 ms
PRSTIM.
*On
PRSLON1.
Off
PRSLON0.
Presentation Default
PRSDFT.
Output Selections
Beeper Volume
7 - 16
*High
BEPVOL50.
Medium
BEPVOL25.
Low
BEPVOL5.
Off
BEPVOL0.
IMAGETEAM™ 4410/4710 User’s Guide
Selection
Power Up Beeper
Setting
* Indicates Default Setting
Serial Command
*Enable
BEPRST1.
Disable
BEPRST0.
*On
BEPCLK1.
Off
BEPCLK0.
Beep On Decode
*On
BEPDEC1.
Beeper Volume
Off
Output Sequence Beeper
Beeper Default
Intercharacter Delay
User Specified Intercharacter
Delay
BEPDEC0.
BEPDFT.
DLYCHR.
Character to Trigger Delay
DLY_XX.
Delay Length
DLYCRX.
Interfunction Delay
DLYFNC.
Intermessage Delay
DLYMSG.
Prefix/Suffix Selections
Add CR Suffix to All Symbologies
SUFBK2990D.
Add Code I.D. Prefix to All Symbologies
PREBK2995C80.
Add AIM I.D. Prefix to All Symbologies
PREBK2995C81.
Prefix
Add Prefix
PREBK2.
Clear One Prefix
PRECL2.
Clear All Prefixes
PRECA2.
Save Current Prefix Changes
MNUSAV.
Discard Current Prefix Changes
MNUABT.
Suffix
Add Suffix
SUFBK2.
Clear One Suffix
SUFCL2.
Clear All Suffixes
SUFCA2.
Save Current Suffix Changes
MNUSAV.
Discard Current Suffix Changes
MNUABT.
Data Formatter Selections
Data Format Editor
*No Format
DFMDF3.
Enter Format
DFMBK3.
Clear One Format
DFMCL3.
Clear All Formats
DFMCA3.
Save Current Data Format Changes
MNUSAV.
Discard Current Data Format Changes
MNUABT.
IMAGETEAM™ 4410/4710 User’s Guide
7 - 17
Selection
Data Formatter
Require Data Format
Setting
* Indicates Default Setting
*On
DFM_EN1.
Off
DFM_EN0.
Require
DFM_EN2.
Show Data Formats
Alternate Data Formats
Serial Command
DFMBK3?.
1
VSAF_1.
2
VSAF_2.
3
VSAF_3.
Output Sequence Selections
Require Output Sequence
Output Sequence Editor
Require
SEQ_EN2.
On/Not Required
SEQ_EN1.
Off
SEQ_EN0.
*Default Sequence
SEQDFT.
Enter Sequence
Save Current Sequence Changes
Discard Current Sequence Changes
Multiple Symbols
No Read
Print Weight
MNUABT.
*Off
SHOTGN0.
On
SHOTGN1.
*Off
SHWNRD0.
On
SHWNRD1.
Default
Set Print Weight
Video Reverse
Function Code Transmit
SEQBLK.
MNUSAV.
PRTWGT4.
PRTWGT.
*Off
VIDREV0.
On
VIDREV1.
Off
RMVFNC0.
*On
RMVFNC1.
Linear Symbology Selections
Codabar
Codabar
Codabar Start/Stop Char.
Codabar Message Length
7 - 18
*Default All Codabar
Settings*
CBRDFT.
*On
CBRENA1.
Off
CBRENA0.
*Don’t Transmit
CBRSSX0.
Transmit
CBRSSX1.
Minimum
CBRMIN.
Maximum
CBRMAX.
IMAGETEAM™ 4410/4710 User’s Guide
Selection
Codabar Check Char.
Code 39
Code 39
Code 39 Start/Stop Char.
Code 39 Full ASCII
Code 39 Message Length
Code 39 Check Char.
Code 39 Mesa Composite
Code 11
Code 11
Code 11 Message Length
Code 11 Check Digits
Required
Interleaved 2 of 5
Interleaved 2 of 5
Interleaved 2 of 5 Message
Length
Setting
* Indicates Default Setting
Serial Command
*No Check Char.
CBRCK20.
Validate, But
Don’t Transmit
CBRCK21.
Validate,
and Transmit
CBRCK22.
*Default All Code 39
Settings*
C39DFT.
*On
C39ENA1.
Off
C39ENA0.
*Don’t Transmit
C39SSX0.
Transmit
C39SSX1.
*Off
C39ASC0.
On
C39ASC1.
Minimum
C39MIN.
Maximum
C39MAX.
*No Check Char.
C39CK20.
Validate, But Don’t
Transmit
C39CK21.
Validate,
and Transmit
C39CK22.
On
3MSENA1.
*Off
3MSENA0.
*Default All Code 11
Settings*
C11DFT.
On
C11ENA1.
*Off
C11ENA0.
Minimum
C11MIN.
Maximum
C11MAX.
1 Check Digit
C11CK20.
*2 Check Digits
C11CK21.
*Default All Interleaved
2 of 5 Settings*
I25DFT.
*On
I25ENA1.
Off
I25ENA0.
Minimum
I25MIN.
Maximum
I25MAX.
IMAGETEAM™ 4410/4710 User’s Guide
7 - 19
Selection
Interleaved 2 of 5 Check Digit
Interleaved 2 of 5 Mesa Composite
IATA 2 of 5
IATA 2 of 5
IATA 2 of 5 Message Length
MSI
MSI
MSI
MSI Check Digit
Code 93
Code 93
Code 93 Message Length
Code 93 Mesa Composite
Code 128
Code 128
Code 128 Message Length
Code 128 ISBT
7 - 20
Setting
* Indicates Default Setting
Serial Command
*No Check Char.
I25CK20.
Validate, But Don’t
Transmit
I25CK21.
Validate,
and Transmit
I25CK22.
On
IMSENA1.
*Off
IMSENA0.
*Default All IATA
2 of 5 Settings*
A25DFT.
On
A25ENA1.
*Off
A25ENA0.
Minimum
A25MIN.
Maximum
A25MAX.
*Default All MSI Settings*
MSIDFT.
On
MSIENA1.
*Off
MSIENA0.
Minimum
MSIMIN.
Maximum
MSIMAX.
Transmit
MSICKX1.
*Don’t Transmit
MSICKX0.
*Default All Code 93
Settings*
C93DFT.
On
C93ENA1.
*Off
C93ENA0.
Minimum
C93MIN.
Maximum
C93MAX.
On
9MSENA1.
*Off
9MSENA0.
*Default All Code 128
Settings*
128DFT.
*On
128ENA1.
Off
128ENA0.
Minimum
128MIN.
Maximum
128MAX.
*Off
ISBENA0.
On
ISBENA1.
IMAGETEAM™ 4410/4710 User’s Guide
Selection
Code 128 Mesa Composite
EAN/JAN 8
EAN/JAN 8
EAN/JAN 8 Check Digit
EAN/JAN 8 2 Digit Addenda
EAN/JAN 8 5 Digit Addenda
EAN/JAN 8 Addenda Required
EAN/JAN 8 Addenda
Separator
EAN/JAN 13
EAN/JAN 13
EAN/JAN 13 Check Digit
EAN/JAN 13 2 Digit Addenda
EAN/JAN 13 5 Digit Addenda
Setting
* Indicates Default Setting
Serial Command
On
1MSENA1.
*Off
1MSENA0.
*Default All EAN/
JAN 8 Settings*
EA8DFT.
On
EA8ENA1.
*Off
EA8ENA0.
*Don’t Transmit
EA8CKX0.
Transmit
EA8CKX1.
*Off
EA8AD20.
On
EA8AD21.
*Off
EA8AD50.
On
EA8AD51.
*Not Required
EA8ARQ0.
Required
EA8ARQ1.
*No Space
EA8ADS0.
Space
EA8ADS1.
*Default All EAN/
JAN 13 Settings*
E13DFT.
*On
E13ENA1.
Off
E13ENA0.
*Don’t Transmit
E13CKX0.
Transmit
E13CKX1.
*Off
E13AD20.
On
E13AD21.
*Off
E13AD50.
On
E13AD51.
EAN/JAN 13 Addenda
Required
*Not Required
E13ARQ0.
Required
E13ARQ1.
EAN/JAN 13 Addenda
Separator
*No Space
E13ADS0.
Space
E13ADS1.
EAN Mesa Composite
UPC A
UPC A
On
EMSENA1.
*Off
EMSENA0.
*Default All
UPC A Settings*
UPADFT.
*On
UPAENA1.
Off
UPAENA0.
IMAGETEAM™ 4410/4710 User’s Guide
7 - 21
Selection
UPC A Check Digit
UPC A Number System
UPC A 2 Digit Addenda
UPC A 5 Digit Addenda
UPC A Addenda Required
UPC A Addenda
Separator
UPC E0
UPC E0
UPC E0 Check Digit
UPC E0 Number System
UPC E0 Version E Expand
UPC E1
UPC E0/E1 2 Digit Addenda
UPC E0/E1 5 Digit Addenda
UPC E0/E1 Addenda Required
UPC E0/E1 Addenda
Separator
UPC Mesa Composite
RSS-14
7 - 22
Setting
* Indicates Default Setting
*Don’t Transmit
Serial Command
UPACKX0.
Transmit
UPACKX1.
Don’t Transmit
UPANSX0.
*Transmit
UPANSX1.
*Off
UPAAD20.
On
UPAAD21.
*Off
UPAAD50.
On
UPAAD51.
*Not Required
UPAARQ0.
Required
UPAARQ1.
*No Space
UPAADS0.
Space
UPAADS1.
*Default All UPC E0
Settings*
UE0DFT.
On
UE0ENA1.
*Off
UE0ENA0.
*Don’t Transmit
UE0CKX0.
Transmit
UE0CKX1.
*Don’t Transmit
UE0NSX0.
Transmit
UE0NSX1.
*Don’t Expand
UE0EXP0.
Expand
UE0EXP1.
On
UE1ENA1.
*Off
UE1ENA0.
*Off
UPEAD20.
On
UPEAD21.
*Off
UPEAD50.
On
UPEAD51.
*Not Required
UPEARQ0.
Required
UPEARQ1.
*No Space
UPEADS0.
Space
UPEADS1.
On
UMSENA1.
*Off
UMSENA0.
*Default All
RSS-14 Settings*
RSSDFT.
IMAGETEAM™ 4410/4710 User’s Guide
Selection
RSS-14
RSS-14 Limited
RSS-14 Limited
RSS-14 Limited
RSS Expanded
RSS Expanded Msg. Length
Setting
* Indicates Default Setting
Serial Command
On
RSSENA1.
*Off
RSSENA0.
*Default All RSS-14
Limited Settings*
RSLDFT.
On
RSLENA1.
*Off
RSLENA0.
*Default All RSS-14
Expanded Settings*
RSEDFT.
On
RSEENA1.
*Off
RSEENA0.
Minimum
RSEMIN.
Maximum
RSEMAX.
Stacked Symbology Selections
Codablock
Codablock
Codablock
Msg. Length
PDF417
PDF417
PDF417 Message Length
MicroPDF417
MicroPDF417
MicroPDF417
Message Length
Code 49
Code 49
*Default All Codablock Settings*
CBFDFT.
On
CBFENA1.
*Off
CBFENA0.
Minimum
CBFMIN.
Maximum
CBFMAX.
*Default All PDF417
Settings*
PDFDFT.
*On
PDFENA1.
Off
PDFENA0.
Minimum
PDFMIN.
Maximum
PDFMAX.
*Default All Micro PDF
Settings*
MPDDFT.
*On
MPDENA1.
Off
MPDENA0.
Minimum
MPDMIN.
Maximum
MPDMAX.
*Default All Code 49
Settings*
C49DFT.
On
C49ENA1.
*Off
C49ENA0.
IMAGETEAM™ 4410/4710 User’s Guide
7 - 23
Selection
Code 49 Msg. Length
EAN•UCC Composite Codes
EAN•UCC Composite Msg.
Length
TLC39
Setting
* Indicates Default Setting
Minimum
Serial Command
C49MIN.
Maximum
C49MAX.
On
COMENA1.
*Off
COMENA0.
Minimum
COMMIN.
Maximum
COMMAX.
On
T39ENA1.
*Off
T39ENA0.
Postal Symbology Selections
POSTNET Code (USPS)
POSTNET Check Digit
BPO 4 State Code (BPO)
Canadian 4 State Code
Dutch Code
Australian 4 State Code
Japanese Postal Code
Planet Code
Planet Check Digit
On
NETENA1.
*Off
NETENA0.
*Don’t Transmit
NETCKX0.
Transmit
NETCKX1.
On
BPOENA1.
*Off
BPOENA0.
On
CANENA1.
*Off
CANENA0.
*Off
KIXENA0.
On
KIXENA1.
On
AUSENA1.
*Off
AUSENA0.
On
JAPENA1.
*Off
JAPENA0.
On
PLNENA1.
*Off
PLNENA0.
*Don’t Transmit
PLNCKX0.
Transmit
PLNCKX1.
2D Matrix Symbology Selections
QR Code Settings
QR Code
QR Code Message Length
7 - 24
*Default All QR Code
Settings*
QRCDFT.
On
QRCENA1.
*Off
QRCENA0.
Minimum
QRCMIN.
Maximum
QRCMAX.
IMAGETEAM™ 4410/4710 User’s Guide
Selection
Data Matrix Settings
Data Matrix
Data Matrix Msg. Length
MaxiCode Settings
MaxiCode
MaxiCode Msg. Length
SCM Only
Aztec Code Settings
Aztec Code
Aztec Code Msg. Length
Test Menu
Print Quality Assessment
Setting
* Indicates Default Setting
*Default All Data
Matrix Settings*
Serial Command
IDMDFT.
*On
IDMENA1.
Off
IDMENA0.
Minimum
IDMMIN.
Maximum
IDMMAX.
*Default All MaxiCode
Settings*
MAXDFT.
On
MAXENA1.
*Off
MAXENA0.
Minimum
MAXMIN.
Maximum
MAXMAX.
*Off
MAXSCM0.
On
MAXSCM1.
*Default All Aztec
Code Settings*
AZTDFT.
*On
AZTENA1.
Off
AZTENA0.
Minimum
AZTMIN.
Maximum
AZTMAX.
*Off
TSTMNU0.
On
TSTMNU1.
*Off
2D_PQA0.
On
2D_PQA1.
IMAGETEAM™ 4410/4710 User’s Guide
7 - 25
Selection
OCR
Setting
* Indicates Default Setting
Serial Command
*Default All OCR Settings*
OCRDFT.
*All OCR Off
OCRENA0.
OCR-A On
OCRENA1.
OCR-B On
OCRENA2.
U.S. Currency On
OCRENA3.
Enter OCR Template
OCRTMP.
Enter User-Defined Variable “g”
OCRGPG.
Enter User-Defined Variable “h”
OCRGPH.
OCR Modulo 10 Check
Character
OCRCHK”0123456789”.
OCR Modulo 36 Check
Character
OCRCHK”0123456789A
BCDEFGHIJKLM
NOPQRSTUVWXYZ”.
*Direction – left-to-right
ORCDIR0.
Direction – top-to-bottom
ORCDIR1.
Direction – right-to-left
ORCDIR2.
Direction – bottom-to-top
ORCDIR3.
Save OCR Template
MNUSAV.
Discard OCR Template
MNUABT.
1. XX = decimal value. Trigger on is defaulted to 18 and trigger off is defaulted to 20.
2. See the SDK User’s Guide for the commands needed to utilize Hardware Triggering.
7 - 26
IMAGETEAM™ 4410/4710 User’s Guide
Imaging Commands
Image Commands Help File
If you send the IMGCMD command to the imager, the imager sends out an ASCII
“help file” that describes the available imager capture commands. Explanations
of the most commonly used imager capture commands follow.
Image Ship
An image is taken whenever the trigger of the IT4410/4710 is depressed. The
last image is always stored in memory. You may “ship” the image by using the
IMGSHP command. The image ship command has many different modifiers that
can be used to change the look of the image that is output by the scanner. The
default image file format used by IMGSHP is a gray scale KIM.
IMGSHP Modifiers
Compensation: flattens the image to account for variations in illumination
across the image.
0C - compensation disabled
1C - compensation enable, default
Pixel Ship:can be used to decimate the image by shipping only certain regularly
spaced pixels. There is no limit to the number of pixels that can be skipped;
although after a certain point, the image becomes unusable.
1S - ship every pixel
2S - ship every 2nd pixel, both horizontally and vertically, default
3S - ship every 3rd pixel, both horizontally and vertically
Image Cropping: Ship a window of the image
xxxT - top of image with xxx indicating the pixel row at which to start
shipping. Range: 000 - 480.
xxxB - bottom of image with xxx indicating the pixel row at which to stop
shipping. Range: 000 - 480.
xxxL - left of image with xxx indicating the pixel column at which to start
shipping. Range: 000 - 640.
xxxR - right of image with xxx indicating the pixel column at which to stop
shipping. Range: 000 - 640.
Image File Format: Indicates the type of file format in which to save the image
0F - KIM format, default
1F - TIFF Binary
2F - TIFF Binary Group 4 Compressed
3F - TIFF Gray scale
4F - Uncompressed Binary
IMAGETEAM™ 4410/4710 User’s Guide
7 - 27
5F - Uncompressed Gray scale
6F - JPEG image
7F - Outlined image
JPEG Image Quality
xJ (x = 1 - 100)
1J = worst quality
100J = best quality
Pixel Depth:Indicates the number of bits.
8D - 8 bit, gray scale image
1D - 1 bit, black and white image
Image Inversion:Used to invert the image in fix mount applications where the
imager is mounted upside down.
0I - no inversion, default
1I - inversion
Image Capture/Ship and Image Get Commands
Close Image Capture - IMGCAP
The imager command, IMGCAP, sets up the imager to capture and ship an
image the next time the imager’s trigger is pulled. All of the modifiers available
for the IMGSHP command (page 7-27) also are available for the IMGCAP
command to change the look of the image that is output by the scanner. When
using the IMGCAP command, the imager is optimized to capture images of close
objects (e.g., signatures, address labels). The default image file format used by
IMGCAP is a gray scale KIM.
Far Away Image Capture - IMGGET
The imager command, IMGGET, works the same way as the IMGCAP
command, except the imager is set up for capturing images of scenes, similar to
a digital camera. The allowable exposure times that the imager uses are longer
than those for IMGCAP to account for the fact that the imager’s LEDs have little
effect at longer distances. The default image file format used by IMGGET is
JPEG.
7 - 28
IMAGETEAM™ 4410/4710 User’s Guide
Image Cropping/Shipping Example
The figure below illustrates the cropping of an area (shaded) of the image. The
cropped area is shipped and stored as a one bit, black and white JPEG. The
cropped area would be 270 pixels by 290 pixels with the following designations:
Top = 000; Bottom = 270; Left = 350; Right = 640.
The command string would be IMGSHP000T270B350L640R6F1D.
350
0
640
Top
Cropped Area
210
Bottom
Default
Center
270
Left
Right
480
Intelligent Signature Capture Commands
Intelligent signature capture is a method to ship only the part of an image to the
host application. This method is reduces transfer time and file size while making
signature capture easy.
Below is an example of an intelligent signature capture application. In this
example, the operator reads the bar code, which is then transmitted to the host
application. Upon the receipt of the bar code data, the host application sends the
“IMGBOX” command, which tells the scanner to output only the area of the image
corresponding to the signature capture box. The scanner also automatically
adjusts for aspect ratio and distortion issues that arise due to scanner skew with
respect to the bar code.
IMAGETEAM™ 4410/4710 User’s Guide
7 - 29
An important aspect of the intelligent signature capture functionality is that all
dimensions used in the application are measured as multiples of the minimum
element size of the bar code. Using this method, intelligent signature capture
always outputs the correct image size and resolution no matter the distance at
which the scanner is held from the bar code, assuming that the entire signature
capture area is within the scanner’s field of view.
negative
positive
0123456789
The intelligent signature capture for this application is:
IMGBOX40S0X70Y190W100H1R0F
IMGBOX Modifiers
S - Bar Code Aspect Ratio: This is the ratio of the bar code height to the narrow
element width. In the above example, the narrow element width is 10 mil (0.010”)
and the bar code height is 0.400 inches, resulting in a value of S = 0.400/0.010
0 = 40.
X - Horizontal Bar Code Offset: This is the horizontal ratio offset of the center
of the signature capture area in multiples of the minimum bar width. In the above
example, the horizontal offset is 0.
Y - Vertical Bar Code Offset: This is the vertical offset of the center of the
signature capture area in multiples of the minimum bar width. Negative numbers
indicate that the signature capture is above the bar code and positive numbers
indicate that the area is below the bar code. In the above example, the horizontal
offset is 0.70,” resulting in a value for Y = 0.70/0.010 = 70.
H - Height of Signature Capture Area: In the above example, the height of the
area to be captured is 1.00,” resulting in a value of H = 1.00”/0.010 = 100. The
value for H is slightly larger to have some extra image capture area outside of the
signature capture box.
W - Width of Signature Capture Area: In the above example, the width of the
area to be captured is 1.90,” resulting in a value of W = 1.90”/0.010” = 190. The
value for W is slightly larger to have some extra image capture area outside of
the signature capture box.
R - Resolution of Signature Capture Area: This is the number of pixels that the
imager outputs per each minimum bar width. The higher the value for R, the
higher the quality of the image, but also the larger the file size.
D - Pixel Depth:
1D - binarized image
8D - gray scale image
7 - 30
IMAGETEAM™ 4410/4710 User’s Guide
F - File Format:
0F - KIM format, default
1F - TIFF Binary
2F - TIFF Binary Group 4 Compressed
3F - TIFF Gray scale
4F - Uncompressed Binary
5F - Uncompressed Gray scale
6F - JPEG image
7F - Outlined image
IMAGETEAM™ 4410/4710 User’s Guide
7 - 31
7 - 32
IMAGETEAM™ 4410/4710 User’s Guide
IMAGETEAM™ 4410/4710 User’s Guide
7 - 33
7 - 34
IMAGETEAM™ 4410/4710 User’s Guide
8
Visual Menu
Visual Menu Introduction
Visual Menu provides the ability to configure a scanning device by connecting
the scanner to the com port of a PC. Visual Menu allows you to download
upgrades to a scanner’s firmware, change programmed parameters, and create
and print programming bar codes. Using Visual Menu, you can even set up the
configuration for a scanner which is not attached to your PC. This enables one
expert user to establish the configuration settings for all the devices your
company uses, then save these configuration files for others. A configuration file
can be e-mailed or, if you prefer, an expert user can create a bar code (or series
of bar codes) which contains all the customized programming parameters, and
mail or fax the bar code(s) to any location. Users in other locations can scan the
bar code(s) to load in the customized parameters.
To communicate with a scanner, Visual Menu requires that the PC have at least
one available serial communication port and an RS-232 cable to connect the port
to the device. A power supply, which plugs into the cable, is also required.
Visual Menu Operations
The Visual Menu program performs the following operations:
• Displays all configuration data, and saves the information to a file on your PC.
• Configures the device to meet your specific requirements. Visual Menu has
all the programming parameters which are available via programming bar
codes in this User’s Guide.
• Creates and prints a clone bar code which contains the program and
configuration data from one device. This bar code can then be used to
program additional devices with the same parameters.
• Selects a device from a list, then performs offline or online file configuration
for that device.
IMAGETEAM™ 4410/4710 User’s Guide
8-1
Temporary Visual Menu Configuration
For quick download communication configuration, scan the Visual Menu bar
code to temporarily configure the scanner for Visual Menu settings.
Note: If you have a unit capable of keyboard wedge mode, scan the bar code
below and the unit will communicate in RS-232 mode, allowing it to work
with Visual Menu. To convert the scanner back to keyboard wedge
communication, cycle the power.
Visual Menu
Installing Visual Menu from the Web
1. Access the Hand Held Products web site at www.handheld.com.
2. Click on the Quick Search text box and enter Visual Menu.
3. Click on Search Now.
4. Click on the entry for Visual Menu.
5. When prompted, select Save File, and save the files to the
c:\windows\temp directory.
6. Once you have finished downloading the file, exit the web site.
7. Using Explorer, go to the c:\windows\temp file.
8. Double click on the Visualmenu.exe file. Follow the screen prompts to
install the Visual Menu program.
9. To start Visual Menu, from the Start Menu click on Programs, Visual Menu,
Visual Menu.
Note: If you wish, you can create a shortcut to the Visual Menu executable on
your desktop.
8-2
IMAGETEAM™ 4410/4710 User’s Guide
9
Interface Keys
Supported
Interface Keys
IBM AT/XT
and PS/2
Compatibles,
WYSE PC/AT
IBM XTs and
Compatibles
IBM, DDC,
Memorex Telex,
Harris*
NUL
00
Reserved
Reserved
Reserved
SOH
01
Enter (KP)
CR/Enter
Enter
STX
02
Caps Lock
Caps Lock
F11
ETX
03
ALT make
Reserved
F12
EOT
04
ALT break
Reserved
F13
ENQ
05
CTRL make
Reserved
F14
ACK
06
CTRL break
Reserved
F15
BEL
07
CR/Enter
CR/Enter
New Line
BS
08
Reserved
Reserved
F16
HT
09
Tab
Tab
F17
LF
0A
Reserved
Reserved
F18
VT
0B
Tab
Tab
Tab/Field Forward
FF
0C
Delete
Delete
Delete
CR
0D
CR/Enter
CR/Enter
Field Exit/New Line
SO
0E
Insert
Insert
Insert
SI
0F
Escape
Escape
F19
DLE
10
F11
Reserved
Error Reset
DC1
11
Home
Home
Home
DC2
12
Print
Print
F20
DC3
13
Back Space
Back Space
Back Space
DC4
14
Back Tab
Back Tab
Backfield/Back Tab
IMAGETEAM™ 4410/4710 User’s Guide
9-1
Supported
Interface Keys
IBM AT/XT
and PS/2
Compatibles,
WYSE PC/AT
IBM XTs and
Compatibles
IBM, DDC,
Memorex Telex,
Harris*
NAK
15
F12
Reserved
F21
SYN
16
F1
F1
F1
ETB
17
F2
F2
F2
CAN
18
F3
F3
F3
EM
19
F4
F4
F4
SUB
1A
F5
F5
F5
ESC
1B
F6
F6
F6
FS
1C
F7
F7
F7
GS
1D
F8
F8
F8
RS
1E
F9
F9
F9
US
1F
F10
F10
F10
*. IBM 3191/92, 3471/72, 3196/97, 3476/77, Telex (all models)
Supported
Interface Keys
IBM, Memorex
Telex (102)*
Memorex
Telex (88)**
NUL
00
Reserved
Reserved
SOH
01
Enter
Enter
STX
02
F11
PF10
ETX
03
F12
PF11
EOT
04
F13
PF12
ENQ
05
F14
Reserved
ACK
06
F15
Reserved
9-2
IMAGETEAM™ 4410/4710 User’s Guide
Supported
Interface Keys
IBM, Memorex
Telex (102)*
Memorex
Telex (88)**
BEL
07
New Line
New Line
BS
08
F16
Field Forward
HT
09
F17
Field Forward
LF
0A
F18
Reserved
VT
0B
Tab/Field Forward
Field Forward
FF
0C
Delete
Delete
CR
0D
Field Exit
New Line
SO
0E
Insert
Insert
SI
0F
Clear
Erase
DLE
10
Error Reset
Error Reset
DC1
11
Home
Reserved
DC2
12
Print
Print
DC3
13
Back Space
Back Space
DC4
14
Back Tab
Back Field
NAK
15
F19
Reserved
SYN
16
F1
PF1
ETB
17
F2
PF2
CAN
18
F3
PF3
EM
19
F4
PF4
SUB
1A
F5
PF5
ESC
1B
F6
PF6
FS
1C
F7
PF7
GS
1D
F8
PF8
RS
1E
F9
PF9
IMAGETEAM™ 4410/4710 User’s Guide
9-3
Supported
Interface Keys
IBM, Memorex
Telex (102)*
Memorex
Telex (88)**
US
F10
Home
1F
*. IBM 3196/97, 3476/77, 3191/92, 3471/72, Memorex Telex (all models) with 102 key keyboards
**.Memorex Telex with 88 key keyboards
Supported
Interface Keys
Esprit 200, 400
ANSI
Esprit 200, 400
ASCII
Esprit 200, 400
PC
NUL
00
Reserved
Reserved
Reserved
SOH
01
New Line
New Line
New Line
STX
02
N/A
N/A
N/A
ETX
03
N/A
N/A
N/A
EOT
04
N/A
N/A
N/A
ENQ
05
N/A
N/A
N/A
ACK
06
N/A
N/A
N/A
BEL
07
New Line
New Line
New Line
BS
08
N/A
N/A
N/A
HT
09
Tab
Tab
Tab
LF
0A
N/A
N/A
N/A
VT
0B
Tab
Tab
Tab
FF
0C
N/A
N/A
Delete
CR
0D
New Line
New Line
New Line
SO
0E
N/A
N/A
Insert
SI
0F
Escape
Escape
Escape
DLE
10
F11
F11
F11
DC1
11
Insert
Insert
Home
9-4
IMAGETEAM™ 4410/4710 User’s Guide
Supported
Interface Keys
Esprit 200, 400
ANSI
Esprit 200, 400
ASCII
Esprit 200, 400
PC
DC2
12
F13
F13
Print
DC3
13
Back Space
Back Space
Back Space
DC4
14
Back Tab
Back Tab
Back Tab
NAK
15
F12
F12
F12
SYN
16
F1
F1
F1
ETB
17
F2
F2
F2
CAN
18
F3
F3
F3
EM
19
F4
F4
F4
SUB
1A
F5
F5
F5
ESC
1B
F6
F6
F6
FS
1C
F7
F7
F7
GS
1D
F8
F8
F8
RS
1E
F9
F9
F9
US
1F
F10
F10
F10
IMAGETEAM™ 4410/4710 User’s Guide
9-5
9-6
IMAGETEAM™ 4410/4710 User’s Guide
10
Product Specifications & Pinouts
Product Specifications - IT4410
Parameter
Specification
Dimensions
Length
Height
Width
6.1 inches (15.4 cm)
5.6 inches (14.2 cm)
2.5 inches (6.4 cm)
Weight
Less than 7 ounces (198 g), without cable
Illumination Source
660 nm illumination LEDs
Aiming Pattern Source
660 nm illumination LEDs
Focal Point (focus)
LX
7 inches (17.8 cm) from Imager’s nose
Long Range
5 inches (12.7 cm) from Imager’s nose
High Density
2 inches (5.1 cm) from Imager’s nose
High Density10
3 inches (7.62 cm) from Imager’s nose
Field of View
LX
4.3 inches (10.92 cm) by 3.25 inches (8.26 cm) @ 7.0”
Long Range
3 inches (7.6 cm) by 2.25 inches (5.7 cm) @ 5.0”
High Density
1.35 inches (3.4 cm) by 1.0 inches (2.5 cm) @ 2.0”
High Density10
1.9 inches (4.8 cm) by 1.5 inches (3.8 cm) @ 3.0”
Rotational Sensitivity
360° around optical axis
Viewing Angle
±45° at the nominal operating distance
Motion Sensitivity
approx. 2 inches (5 cm) per second of lateral motion
Ambient Light
Total darkness to 100,000 Lux (sunlight)
Video Image
8-bits per pixel
Operating Voltage
4.0 VDC - 9.0 VDC
Power Supply
Peak Current
5 VDC input
550 mA (when illumination LEDs are on)
Current Draw - 4410
Low Power Mode
Medium Power Mode
Normal Power Mode
Average @ 5 VDC - 40mA
Average @ 5 VDC - 125mA
Average @ 5 VDC - 175mA
Temperature Ranges
Operating 32° F to +122° F (-0C to +50C)
Storage -40° F to +158° F (-40C to +70C)
Humidity
95% RH non-condensing, at +50° C
Mechanical Shock
10 drops from 5 feet (1.5 m) to concrete
IMAGETEAM™ 4410/4710 User’s Guide
10 - 1
Parameter
Specification
ESD Sensitivity
15 kV to any external surface
Agency Compliance
FCC Class B
Canadian Class B
CE 55022 Class B
UL/CUL Listed to UL1950 CSA 22.2 950
TUV Certified to EN60950 and EN 60825-1 Class 1
CTick N10410
GS
Product Specifications - IT4710
Parameter
Dimensions
Length
Height
Width
Specification
4.85 inches (12.3 cm)
1.85 inches (4.7 cm)
2.5 inches (6.4 cm)
Weight
Less than 5.5 ounces 198 g), without cable
Illumination Source
660 nm illumination LEDs
Aiming Pattern Source
660 nm illumination LEDs
Focal Point (focus)
LX
7 inches (17.8 cm) from Imager’s nose
Long Range
5 inches (12.7 cm) from Imager’s nose
High Density
2 inches (5.1 cm) from Imager’s nose
High Density10
3 inches (7.62 cm) from Imager’s nose
Field of View
LX
4.3 inches (10.92 cm) by 3.25 inches (8.26 cm) @ 7.0”
Long Range
3 inches (7.6 cm) by 2.25 inches (5.7 cm) @ 5.0”
High Density
1.35 inches (3.4 cm) by 1.0 inches (2.5 cm) @ 2.0”
High Density10
1.9 inches (4.8 cm) by 1.5 inches (3.8 cm) @ 3.0”
Rotational Sensitivity
360° around optical axis
Viewing Angle
±45° at the nominal operating distance
Motion Sensitivity
approx. 2 inches (5 cm) per second of lateral motion
Ambient Light
Total darkness to 100,000 Lux (sunlight)
Video Image
8-bits per pixel
Operating Voltage
4.0 VDC - 9.0 VDC
Power Supply
Peak Current
5 VDC input
550 mA (when illumination LEDs are on)
10 - 2
IMAGETEAM™ 4410/4710 User’s Guide
Parameter
Specification
Current Draw
Low Power Mode
Medium Power Mode
High Power Mode
Average @ 5 VDC - 40mA
Average @ 5 VDC - 125mA
Average @ 5 VDC - 175mA
Temperature Ranges
Humidity
Operating 32° F to +122° F (-0C to +50C)
Storage -40° F to +158° F (-40C to +70C)
95% RH non-condensing, at +50° C
Mechanical Shock
10 drops from 5 feet (1.5 m) to concrete
ESD Sensitivity
15 kV to any external surface
Agency Compliance
FCC Class B
Canadian Class B
CE 55022 Class B
UL/CUL Listed to UL1950 CSA 22.2 950
TUV Certified to EN60950 and EN 60825-1 Class 1
CTick
GS
IMAGETEAM™ 4410/4710 User’s Guide
10 - 3
Depth of Field Charts
All depth of field measurements are made from the IT4410/4710 lens plate,
which is .100” (.25 cm) from the front surface of the IT4410/4710 window.
Depth of Field for High Density Imager (2" Nominal Focus)
Code Size
Near Distance
Far Distance
QR 6.6 mil (0.017 cm)
1.7 inches (4.3 cm)
2.4 inches (6.1 cm)
Data Matrix 6.6 mil (0.017 cm)
1.7 inches (4.3 cm)
2.4 inches (6.1 cm)
Linear 4 mil (0.01 cm)
1.7 inches (4.3 cm)
2.9 inches (7.4 cm)
OCR 6 pt. (20 cpi)
2 inches (5.1 cm)
3.5 inches (8.9 cm)
Depth of Field for High Density10 Imager (3" Nominal Focus)
Code Size
Near Distance
Far Distance
QR 10 mil (0.025 cm)
2.0 inches (5.1 cm)
4.0 inches (10.2 cm)
Data Matrix 10 mil (0.025 cm)
2.2 inches (5.6 cm)
3.8 inches (9.7 cm)
Linear 5 mil (0.013 cm)
2.75 inches (7.0 cm)
3.75 inches (9.5 cm)
OCR 12 pt. (12 cpi)
2 inches (5.1 cm)
5 inches (12.7 cm)
Depth of Field for Long Range Imager (5" Nominal Focus)
Code Size
Near Distance
Far Distance
Linear 5 mil (.0127 cm)
3.0 inches (7.6 cm)
4.3 inches (10.9 cm)
Linear 10 mil (0.025 cm)
2.4 inches (6.1 cm)
8 inches (20.3 cm)
Data Matrix 15 mil (0.038 cm)
2.0 inches (5.1 cm)
5.8 inches (14.7 cm)
UPC 13 mil (0.033 cm)
1.9 inches (4.8 cm)
9.4 inches (23.9 cm)
QR 15 mil (0.038 cm)
1.7 inches (4.3 cm)
6 inches (15.2 cm)
MaxiCode 35 mil (0.089 cm)
2 inches (5.1 cm)
10.5 inches (26.7 cm)
12 pt. OCR-A
1.9 inches (4.8 cm)
8.7 inches (22.1 cm)
16 pt. OCR-A
2.3 inches (5.8 cm)
9.3 inches (23.6 cm)
Linear 15 mil (0.038 cm)
2.2 inches (5.6 cm)
9.9 inches (25.2 cm)
PDF 6.6 mil (0.017 cm)
2.7 inches (6.9 cm)
5.2 inches (13.2 cm)
PDF 10 mil (0.025 cm)
2.4 inches (6.1 cm)
7.7 inches (19.6 cm)
10 - 4
IMAGETEAM™ 4410/4710 User’s Guide
Depth of Field for LX Imager (7" Nominal Focus)
Code Size
Near Distance
Far Distance
MaxiCode 35 mil (0.089 cm)
2 inches (5.1 cm)
15 inches (38.1 cm)
Data Matrix 15 mil (0.038 cm)
3.7 inches (9.4 cm)
5.9 inches (15 cm)
PDF 10 mil (0.025 cm)
2.7 inches (6.9 cm)
9.8 inches ((24.9 cm)
PDF 8 mil (0.020 cm)
3.0 inches (7.6 cm)
8.3 inches (21.1 cm)
PDF 6.6 mil (0.017 cm)
4.0 inches (10.2 cm)
6.3 inches (16.0 cm)
Code 39 15 mil (0.038 cm)
2.1 inches (5.3 cm)
13.8 inches (35.1 cm)
Code 39 10 mil (0.025 cm)
2.8 inches (7.1 cm)
9.5 inches (24.1 cm)
Code 39 8 mil (0.020 cm)
3.5 inches (8.9 cm)
8.0 inches (20.3 cm)
UPC 13 mil (0.033 cm)
2.3 inches (5.8 cm)
13 inches (33.0 cm)
Postnet
3.7 inches (9.4 cm)
6.0 inches (15.2 cm)
12 pt. OCR-A
1.6 inches (4.1 cm)
12.3 inches (31.2 cm)
12 pt. OCR-B
1.5 inches (3.8 cm)
11.2 inches (28.5 cm)
IMAGETEAM™ 4410/4710 User’s Guide
10 - 5
Cable Pinouts
RS-232 Output, External Power
Decoded output data format is provided at the modular connector in the
Imager.Interface cables normally supplied with the Imager are terminated with a
10 pin modular plug (P1) and a 9 pin Type D connector (P3) that is compatible
with all Hand Held Products decoders and terminals. See chart below. (The
power pigtail applies to serial wedge cable, which is not shown.)
P2
Power Pig Tail
P2 connects to the
external power
supply.
P1
Pin 1
Pin 10
Inner
Outer
P3
View B-B
9 Pin Type D Female
P3 connects to your terminal.
5
10 Pin Modular Plug
9
6
View A-A
P1 connects to the Imager.
P2
P1
1
2
3
4
5
6
7
8
9
10
SH
1
Inner
NC
Ground
+5VDC
Ground
RXD
TXD
+5VDC
RTS
CTS
TRIG
No Connection
Supply Ground
Power Connection
Supply Ground
Receive Data - Serial Data to Imager
Transmit Data - Serial Data from Imager
Power Connection
Request to Send Data
Clear to Send Data
External Trigger1
Drain Wire (Shield)
Outer
|
0
P3
5 Red
3 Black
2 Green
8 Blue
7 Brown
SH
1. The voltage requirements for external trigger signal are Logic Low <= .3 VDC and
Logic Hig >= 1.8 VDC.
10 - 6
IMAGETEAM™ 4410/4710 User’s Guide
Connector Part Numbers
Listed below are the connector descriptions and part numbers. The suggested
supplier for all of the connectors is Molex, Inc. (www.molex.com).
TTL RS-232 and Laser Emulation Connector
P/N: 52559-0890 (straight)
or
P/N: 52746-0890 (right angle)
Decoder Board Output Flex Strip
P/N: 21020-0075 (2” length specified. Various lengths available.)
Optics Connector
P/N: 52559-2290 (straight)
or
P/N: 52437-2291 (right angle)
Optics-to-Decoder Board Flex Strip
P/N: 21020-0229 (2” length specified. Contact Hand Held Products if other
lengths are needed)
IMAGETEAM™ 4410/4710 User’s Guide
10 - 7
IT4410 Dimensions
6.06 in
[15.38 cm]
2.49 in
[6.32 cm]
Top View
1.53 in
[4.01 cm]
5.62 in
[14.28 cm]
Front View
3/4 View
1.07 in
[2.72 cm]
Side View
10 - 8
IMAGETEAM™ 4410/4710 User’s Guide
IT4710 Dimensions
4.83 in.
(12.27 cm)
2.49 in.
(6.32 cm)
Top View
1.83 in.
(4.65 cm)
1.53 in.
(4.01 cm)
Front View
1.63 in.
(4.14 cm)
1.076 in.
(2.73 cm)
Side View
.538 in.
(1.37 cm)
.630 in.
(1.60 cm)
M4 threaded insert
.25 in. (6.35 mm) depth
Bottom View
IMAGETEAM™ 4410/4710 User’s Guide
10 - 9
10 - 10
IMAGETEAM™ 4410/4710 User’s Guide
11
Maintenance & Troubleshooting
Repairs
Repairs and/or upgrades are not to be performed on this product. These
services are to be performed only by an authorized service center. See page 121 for further information.
Maintenance
The IMAGETEAM 4410/IT4710 Imager provides reliable and efficient operation
with a minimum of care. Although specific maintenance is not required, the
following periodic checks ensure dependable Imager operation:
Cleaning the Imager’s Window
Reading performance may degrade if the Imager’s window is not clean. If the
window is visibly dirty, or if the Imager isn’t operating well, clean the window with
a soft cloth or facial tissue dampened with water (or a mild detergent- water
solution). If a detergent solution is used, rinse with a clean tissue dampened with
water only.
The Imager’s housing may also be cleaned the same way.
!
Caution:
Do not submerge the Imager in water. The Imager’s housing is not
water-tight.
Do not use abrasive wipers or tissues on the Imager’s window abrasive wipers may scratch the window.
Never use solvents (alcohol or acetone) on the housing or
window - solvents may damage the finish or the window.
Inspecting Cords and Connectors
Inspect the Imager’s interface cable and connector for wear or other signs of
damage. A badly worn cable or damaged connector may interfere with Imager
operation. Contact your distributor for information about cable replacement.
Cable replacement instructions are on the next page.
IMAGETEAM™ 4410/4710 User’s Guide
11 - 1
Examining the Imager’s Housing
Routinely examine the Imager’s housing for signs of damage. A damaged
housing may cause the internal components to move and may result in a
malfunctioning Imager.
Replacing the Interface Cable
The standard interface cable is attached to the Imager with an 10-pin modular
connector. When properly seated, the connector is held in the Imager’s handle
by a flexible retention tab. The cable is designed to be field replaceable.
• •Order replacement cables from or from an authorized distributor.
• •When ordering a replacement cable, specify the cable part number of the
original interface cable.
To Replace the IT4410 Interface Cable:
1. Turn the power to the host system OFF.
2. Disconnect the Imager’s cable from the terminal or computer.
3. Locate the small hole on the side of
the Imager’s handle near the base
(cable release).
4. Straighten one end of a paper clip.
5. Insert the end of the paper clip into the
small hole and press in. This
depresses the retention tab, releasing
the connector. Pull the connector out
of the Imager’s handle while
maintaining pressure on the paper
clip.
Cable
Release
6. Replace with the new cable.
Insert the connector into the opening
at the base of the Imager’s handle.
Press firmly. The connector is “keyed” to go in only one way, and will click
into place.
11 - 2
IMAGETEAM™ 4410/4710 User’s Guide
To Replace the IT4710 Interface Cable:
1. Turn the power to the host system OFF.
2. Disconnect the Imager’s cable from the terminal or computer.
3. Insert a small, flat head screwdriver into the slot between the cable and the
back end of the housing.
4. Press the screwdriver tip down to
depress the retention tab,
releasing the connector.
5. Pull the connector out of the
Imager while maintaining
pressure on the screwdriver.
Cable
Release
6. Replace with the new cable.
Insert the connector into the
opening at the base of the Imager. Press firmly. The connector is “keyed” to
go in only one way, and will click into place.
Troubleshooting
The Imager automatically performs self-tests whenever you turn it on. If your
Imager is not functioning properly, review the following Troubleshooting Guide to
try to isolate the problem.
Troubleshooting Guide
Is the power on? Are the illumination LEDs on?
If the illumination LEDs in the Imager aren’t illuminated, check that:
1. The cable is connected properly.
2. The host system power is on (if external power isn’t used).
Is the Imager having trouble reading your symbols?
If the Imager isn’t reading symbols well, check that the symbols:
1. Aren’t smeared, rough, scratched, or exhibiting voids.
2. Aren’t coated with frost or water droplets on the surface.
3. Are enabled in the Imager or in the decoder the Imager connects to.
IMAGETEAM™ 4410/4710 User’s Guide
11 - 3
11 - 4
IMAGETEAM™ 4410/4710 User’s Guide
12
Customer Support
Product Service and Repair
Hand Held Products provides service for all its products through service centers
throughout the world. To obtain warranty or non-warranty service, return the unit
to Hand Held Products (postage paid) with a copy of the dated purchase record
attached. Contact the appropriate location below to obtain a Return Material
Authorization number (RMA #) before returning the product.
North America
Hand Held Products Corporate Offices
Telephone: (800) 782-4263, Option 3
Fax: (704) 566-6015
E-mail: naservice@handheld.com
America Latina
Hand Held Products America Latina
Teléfono: (239) 263-7600
Fax: (239) 263-9689
E-mail: laservice@handheld.com
Brazil
Hand Held Products Brazil
Telephone: +55 (21) 2176-0250
Fax: +55 (21) 2176-0249
E-mail: suporte@handheld.com
Europe, Middle East, and Africa
Hand Held Products Europe
Telephone:+ 31 (0) 40 29 01 633
Fax: + 31 (0) 40 2901631
E-mail: euservice@handheld.com
Asia Pacific
Hand Held Products Asia/Pacific
Telephone: +852-2511-3050
Fax: +852-2511-3557
E-mail: apservice@handheld.com
Japan
Hand Held Products Japan
Telephone: +81-3-5770-6312
Fax: +81-3-5770-6313
E-mail: apservice@handheld.com
IMAGETEAM™ 4410/4710 User’s Guide
12 - 1
Online Product Service and Repair Assistance
You can also access product service and repair assistance online at
www.handheld.com.
Technical Assistance
If you need assistance installing or troubleshooting your imager, please call your
Distributor or the nearest Hand Held Products technical support office:
North America/Canada:
Telephone:
Fax number:
E-mail:
(800) 782-4263, option 4 (8 a.m. to 6 p.m. EST)
(315) 685-4960
natechsupport@handheld.com
Europe, Middle East, and Africa:
TelephoneEuropean Ofc: Int+31 (0) 40 29 01 600
U.K. Ofc:
Int+44 1925 240055
E-mail:
eutechsupport@handheld.com
Asia Pacific:
Telephone:
E-mail:
Int+852-3188-3485 or 2511-3050
aptechsupport@handheld.com
America Latina:
Teléfono:
(704) 998-3998, opción 8
E-mail:
latechsupport@handheld.com
Online Technical Assistance
You can also access technical assistance online at www.handheld.com.
Limited Warranty
Hand Held Products, Inc. ("Hand Held Products") warrants its products to be free
from defects in materials and workmanship and to conform to Hand Held
Products’ published specifications applicable to the products purchased at the
time of shipment. This warranty does not cover any Hand Held Products product
which is (i) improperly installed or used; (ii) damaged by accident or negligence,
including failure to follow the proper maintenance, service, and cleaning
schedule; or (iii) damaged as a result of (A) modification or alteration by the
purchaser or other party, (B) excessive voltage or current supplied to or drawn
from the interface connections, (C) static electricity or electro-static discharge,
(D) operation under conditions beyond the specified operating parameters, or (E)
repair or service of the product by anyone other than Hand Held Products or its
authorized representatives.
12 - 2
IMAGETEAM™ 4410/4710 User’s Guide
This warranty shall extend from the time of shipment for the duration published
by Hand Held Products for the product at the time of purchase ("Warranty
Period"). Any defective product must be returned (at purchaser’s expense)
during the Warranty Period to Hand Held Products’ factory or authorized service
center for inspection. No product will be accepted by Hand Held Products
without a Return Materials Authorization, which may be obtained by contacting
Hand Held Products. In the event that the product is returned to Hand Held
Products or its authorized service center within the Warranty Period and Hand
Held Products determines to its satisfaction that the product is defective due to
defects in materials or workmanship, Hand Held Products, at its sole option, will
either repair or replace the product without charge, except for return shipping to
Hand Held Products.
EXCEPT AS MAY BE OTHERWISE PROVIDED BY APPLICABLE LAW, THE
FOREGOING WARRANTY IS IN LIEU OF ALL OTHER COVENANTS OR
WARRANTIES, EITHER EXPRESSED OR IMPLIED, ORAL OR WRITTEN,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Hand Held Products’ RESPONSIBILITY AND PURCHASER’S EXCLUSIVE
REMEDY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR
REPLACEMENT OF THE DEFECTIVE PRODUCT. IN NO EVENT SHALL
Hand Held Products BE LIABLE FOR INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, AND, IN NO EVENT, SHALL ANY LIABILITY
OF Hand Held Products ARISING IN CONNECTION WITH ANY PRODUCT
SOLD HEREUNDER (WHETHER SUCH LIABILITY ARISES FROM A CLAIM
BASED ON CONTRACT, WARRANTY, TORT, OR OTHERWISE) EXCEED
THE ACTUAL AMOUNT PAID TO Hand Held Products FOR THE PRODUCT.
THESE LIMITATIONS ON LIABILITY SHALL REMAIN IN FULL FORCE AND
EFFECT EVEN WHEN Hand Held Products MAY HAVE BEEN ADVISED OF
THE POSSIBILITY OF SUCH INJURIES, LOSSES, OR DAMAGES. SOME
STATES, PROVINCES, OR COUNTRIES DO NOT ALLOW THE EXCLUSION
OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
All provisions of this Limited Warranty are separate and severable, which means
that if any provision is held invalid and unenforceable, such determination shall
not affect the validity of enforceability of the other provisions hereof. Use of any
peripherals not manufactured/sold by Hand Held Products voids the warranty.
This includes but is not limited to: cables, power supplies, cradles, and docking
stations. Hand Held Products, Inc. extends these warranties only to the first endusers of the products. These warranties are nontransferable.
The limited duration of the warranty for the IT4410/4710 is for 3 years.
IMAGETEAM™ 4410/4710 User’s Guide
12 - 3
12 - 4
IMAGETEAM™ 4410/4710 User’s Guide
Index
A
Add AIM I.D. Prefix to All
Symbologies 2-33
Serial Command 7-17
Add Code I.D. Prefix to All
Symbologies 2-33
Serial Command 7-17
Add CR Suffix to All Symbologies 233
Serial Command 7-17
AIM I.D. Prefix
Add to all Symbologies 2-33
Aimer Delay 2-18
Serial Command 7-16
Aimer Interval 2-19
Serial Command 7-16
Aimer Timeout
Serial Command 7-15
Alternate Data Formats 2-42
Serial Command 7-18
ASCII Conversion Chart 2-36
AutoTrigger Selections
Presentation Mode 2-24
Aztec Code Selections 3-40
Serial Commands 7-25
B
Baud Rate 2-11
Serial Command 7-15
Beeper
Power Up 2-27
Volume
Serial Command 7-16
Boot Code Revision 2-3
Serial Command 7-14
C
Cable
Replacing 11-2
Carriage Return Suffix
Add to all Symbologies 2-33
Centering 2-20
Codabar Selections
Serial Commands 7-18, 7-19
Codablock Selections 4-2
Serial Commands 7-23
Code 128 Selections 3-15
Serial Commands 7-20
Code 39 Selections 3-4
Serial Commands 7-19
Code 49 Selections 3-31
Serial Commands 7-23
Code 93 Selections 3-14
Serial Commands 7-20
Code I.D. Prefix
Add to all Symbologies 2-33
Communication Settings 2-10
Connecting the scanner
Keyboard wedge 1-6
Serial port 1-7
Conversion Chart
Decimal to Hex to ASCII 2-36
D
Data Format
Require 2-41
Serial Command 7-18
Data Format Editor 2-40
Commands 2-38
Overview 2-37
Programming codes 2-40
Serial Command 7-17
Index - 1
Data Formats
Show 2-2, 2-41
Serial Command 7-18
Data Formatter 2-41
Serial Command 7-18
Data Matrix Selections 3-37
Serial Commands 7-25
Decimal to Hex to ASCII Conversion
Chart 2-36
Default Settings 5-1
Dimensions 10-8
Disable All Symbologies 2-2
Serial Command 7-14
E
EAN/JAN 13 Selections 3-19
Serial Commands 7-21
EAN/JAN 8 Selections 3-17
Serial Commands 7-21
EAN•UCC Composite Codes 3-32
Enable All Symbologies 2-2
Serial Command 7-14
F
Flow Control
Hardware 2-13
Serial Command 7-15
Software 2-13
Serial Command 7-15
H
Hardware Flow Control 2-13
Serial Command 7-15
Hex Chart 2-36
I
Iata 2 of 5 Selections 3-11
Index - 2
Installation
Keyboard Wedge 1-6
Serial Port 1-7
Intercharacter Delay 2-28
Serial Command 7-17
Interface Keys 9-1
Interfunction Delay 2-29
Serial Command 7-17
Interleaved 2 of 5 Selections 3-9
Serial Commands 7-19, 7-20
Intermessage Delay 2-30
Serial Command 7-17
ISBT Symbology 3-16
Serial Command 7-20
K
Keyboard Country
Serial Command 7-14
Keyboard Modifiers
Serial Command 7-14
Keyboard Style
Serial Command 7-14
L
Labels
Safety and Identification 1-4
LED
Flashing 2-18
Serial Command 7-16
Power Levels 2-17
Serial Command 7-16
Load New Imager Software
Using Quick*View 7-8
M
Maintenance 11-1
MaxiCode Selections 3-38
Serial Commands 7-25
Micro PDF Selections
Serial Commands 7-23
MicroPDF Selections 3-30
Money
reading serial numbers 4-1
Multiple Symbols
Serial Command 7-18
N
No Read 2-47
Serial Command 7-18
O
OCR Programming 4-1
Online Programming 8-1
Open Com Port 7-7
Output Sequence
Descriptions and Examples 4-4
Require 2-44
Serial Command 7-18
Output Sequence Editor 2-46, 4-9
Serial Command 7-18
Overview 1-1
P
Parity 2-10
Serial Command 7-14
PDF 417 Selections 3-29
Serial Commands 7-23
Postal Code Selections
Serial Commands 7-24
Power Hold Mode 2-17
Serial Command 7-16
Power PC Revision 2-3
Serial Command 7-14
Power Saving Mode
Serial Command 7-15
Power Settings
Using Quick*View 7-8
Power Up Beeper 2-27
Serial Command 7-17
Prefix
Programming codes 2-34
Serial Command 7-17
Prefix/Suffix
Adding or removing 2-32
Prefix/Suffix Overview 2-31
Presentation Default
Serial Command 7-16
Presentation Mode
Default 2-25, 2-27
Presentation Lights 2-25
Presentation Reread Delay 2-24
Serial Command 7-16
Print Weight 2-48
Serial Command 7-18
Q
QR Code Selections
Serial Commands 7-24
Query Commands 7-11
Quick*View 7-1
Button Bar 7-13
Imager Power Settings 7-8
Installation 7-1
Load New Imager Software 7-8
Open Com Port 7-7
Query Commands 7-11
Reporting Firmware Revision 77
RS-232 Serial Commands 7-9
Scan Data Window 7-4
Serial Programming Commands
7-9
Snapshot 7-5, 7-6
Trigger Settings 7-8
Index - 3
R
Reporting Firmware Revision
Using Quick*View 7-7
Require Data Format 2-41
Serial Command 7-18
Require Output Sequence 2-44
Serial Command 7-18
Reset Factory Settings 2-2
Revision Selections 2-3
Serial Commands 7-14
RS-232 Communication
Serial Command 7-14
RSS-14 Selections 3-26
Serial Commands 7-22
S
Scan Data Window 7-4
Scan Stand Selections 2-23
Serial Command 7-16
SCM Selections
Serial Commands 7-25
Serial Programming Commands 7-9
Add AIM I.D. Prefix to All
Symbologies 7-17
Add Code I.D. Prefix to All
Symbologies 7-17
Add CR Suffix to All Symbologies 7-17
Aimer Delay 7-16
Aimer Interval 7-16
Aimer Timeout 7-15
Alternate Data Formats 7-18
Aztec Code Selections 7-25
Baud Rate 7-15
Beeper Volume 7-16
Boot Code Revision 7-14
Codabar Selections 7-18, 7-19
Codablock Selections 7-23
Code 128 Selections 7-20
Index - 4
Code 39 Selections 7-19
Code 49 Selections 7-23
Code 93 Selections 7-20
Data Format Editor 7-17
Data Formatter 7-18
Data Matrix Selections 7-25
Disable All Symbologies 7-14
EAN/JAN 13 Selections 7-21
EAN/JAN 8 Selections 7-21
Enable All Symbologies 7-14
Hardware Flow Control 7-15
Intercharacter Delay 7-17
Interfunction Delay 7-17
Interleaved 2 of 5 Selections 719, 7-20
Intermessage Delay 7-17
ISBT 7-20
Keyboard Country 7-14
Keyboard Modifiers 7-14
Keyboard Style 7-14
LED Flashing 7-16
LED Power Levels 7-16
MaxiCode Selections 7-25
Micro PDF Selections 7-23
Multiple Symbols 7-18
No Read 7-18
Output Sequence Editor 7-18
Parity 7-14
PDF 417 Selections 7-23
Postal Code Selections 7-24
Power Hold Mode 7-16
Power PC Revision 7-14
Power Saving Mode 7-15
Power Up Beeper 7-17
Prefix 7-17
Presentation Default 7-16
Presentation Mode 7-16
Presentation Reread Delay 7-16
Print Weight 7-18
QR Code Selections 7-24
Require Data Format 7-18
Require Output Sequence 7-18
RS-232 Communication 7-14
RSS-14 7-22
Scan Stand 7-16
SCM Selections 7-25
Serial Triggering 7-15
Set Print Weight 7-18
Show Data Formats 7-14, 7-18
Show Software Revision 7-14
Software Flow Control 7-15
Suffix 7-17
Terminal ID 7-14
UPC A Selections 7-21
UPC E0 Selections 7-22
UPC E1 Selections 7-22
Word Length Data Bits 7-15
Word Length Stop Bits 7-15
Serial Triggering 2-14
Serial Command 7-15
Service 12-1
Show Data Formats 2-2, 2-41
Serial Command 7-14, 7-18
Show Software Revision 2-2
Serial Command 7-14
Snapshot 7-5, 7-6
Software Flow Control 2-13
Serial Command 7-15
Software Revision
Show 2-2
Serial Command 7-14
Specifications 10-1, 10-2
Status Check 2-2
Suffix
Programming codes 2-34
Serial Command 7-17
Symbology
Enable/Disable All 2-2
Symbology Chart 2-35
T
Terminal ID
Serial Command 7-14
Trigger Settings
Using Quick*View 7-8
Troubleshooting 11-3
U
Unpacking Imager 1-2
UPC A Selections 3-21
Serial Commands 7-21
UPC E0 Selections 3-23
Serial Commands 7-22
UPC E1 Selections 3-24
Serial Commands 7-22
User Specified Intercharacter Delay
2-28
V
Video Reverse 2-49
Visual Menu 8-1
W
Word Length
Data Bits 2-12
Serial Command 7-15
Stop Bits 2-12
Serial Command 7-15
Index - 5
Index - 6
Sample Symbols
UPC A
0 123456 7890
Interleaved 2 of 5
1234567890
Code 128
Code 128
EAN 13
9 780330 290951
Code 39
BC321
Codabar
A13579B
IMAGETEAM™ 4410/4710 User’s Guide
Sample Symbols
PDF417
Car Registration
Postnet
Zip Code
Code 49
1234567890
Data Matrix
OCR-A Sample
Test Symbol
QR Code
55836540
OCR-B Sample
Numbers
IMAGETEAM™ 4410/4710 User’s Guide
Sample Symbols
Aztec
Package Label
Aztec Mesa Code
Test Message
MaxiCode
Test Message
Micro PDF417
Test Message
IMAGETEAM™ 4410/4710 User’s Guide
Programming Chart (OCR)
a
c
d
e
g
h
IMAGETEAM™ 4410/4710 User’s Guide
Programming Chart (OCR)
l
r
t
Save
IMAGETEAM™ 4410/4710 User’s Guide
Discard
Programming Chart
0
1
2
3
4
5
6
7
IMAGETEAM™ 4410/4710 User’s Guide
Programming Chart
8
9
A
B
C
D
E
F
Save
Discard
Hand Held Products, Inc.
700 Visions Drive
P.O. Box 208
Skaneateles Falls, NY 13153-0208
44-4710-UG Rev D
6/05