Operating instructions | Ford 2008 Escape Hybrid Automobile User Manual

INSTALLER / CONSUMER
SAFETY INFORMATION
Please read this manual before
installing and using appliance.
WARNING: If the information in this
manual is not followed exactly, a fire
or explosion may result causing
property damage, personal injury or
loss of life.
—Do not store or use gasoline or
other flammable vapors and
liquids in the vicinity of this or
any other appliance.
—WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical
switch; do not use any phone
in your building.
• Immediately call your gas
suppler from a neighbor’s
phone. Follow the gas
suppler’s instructions.
• If you cannot reach your gas
supplier, call the fire department.
Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
UVS27R, UVS27M
Vent Free Gas Heaters
Models 3030, 3031,
3032, 3033
Homeowner’s Installation
and Operating Manual
DE S I GN
This is an unvented gas-fired heater.
It uses air (Oxygen) from the room
in which it is installed. Provisions for
adequate combustion and
ventilation air must be provided.
Refer to Page 7.
CE
RTIFI E D
Tested and listed to
ANSI Z21.11.2a-2001, Unvented Heaters
CFM Specialty Home Products
410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 • 905-670-7777
www.majesticproducts.com • www.vermontcastings.com
INSTALLER: DO NOT DISCARD THIS MANUAL - LEAVE FOR HOMEOWNER
20005004 10/04 Rev. 4
Vermont Castings UVS27 Vent-Free Gas Heater
Table Of Contents
PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING APPLIANCE.
Thank you and congratulations on your purchase of a Vermont Castings stove.
IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these
instructions may result in a possible fire hazard and will void the warranty.
Installation and Operating Instructions
Shell Dimensions ............................................................................................................... 4
Clearance Requirements ................................................................................................... 5
Hearth Requirements ......................................................................................................... 5
Gas Specifications ............................................................................................................. 6
Gas Inlet and Manifold Pressures ...................................................................................... 6
High Elevations .................................................................................................................. 6
Odor During Operation ....................................................................................................... 6
Vent Free Features ............................................................................................................ 7
Fresh Air Requirements ..................................................................................................... 7
Assembly Procedures
Unpack the Firebox ............................................................................................................ 9
Shell / Firebox Assembly .................................................................................................... 9
Install Optional Fan Kit ..................................................................................................... 10
Install ON/OFF Switch ...................................................................................................... 11
Thermostat Connections .................................................................................................. 12
Glass & Catalyst Installation ............................................................................................ 12
Connect the Gas Supply LIne .......................................................................................... 13
Install Log Set .................................................................................................................. 14
Complete the Installation .................................................................................................. 15
Operation
Your First Fire .................................................................................................................. 16
Pilot and Burner Inspection .............................................................................................. 16
Flame & Temperature Adjustment ................................................................................... 16
Flame Characteristics ...................................................................................................... 16
Lighting Instructions ......................................................................................................... 17
Troubleshooting ............................................................................................................... 18
Maintenance
Firebox Cleaning and Inspection ...................................................................................... 20
Cleaning Procedure ......................................................................................................... 20
Glass Replacement .......................................................................................................... 20
Care of Cast Iron .............................................................................................................. 20
Catalytic Combustor ......................................................................................................... 21
Replacement Parts ....................................................................................................................... 22
Optional Accessories
Fan Kits ............................................................................................................................ 24
Glass / Catalyst Kit ........................................................................................................... 24
Remote Controls .............................................................................................................. 24
Warming Shelf .................................................................................................................. 24
Warranty ....................................................................................................................................... 26
2
20005004
Vermont Castings UVS27 Vent-Free Gas Heater
Installation & Operating Instructions
In order to ensure safe and effective installation, this unit
must be installed only by a qualified agency, individual, firm,
corporation or company that is experienced in the installation, repair and servicing of this type of appliance and is
familiar with the building codes and installation techniques
appropriate in your area. Contact your hearth products
dealer or local gas supplier for the name of a qualified
service person.
IMPORTANT: Read this owner's manual carefully and
completely before trying to assemble, operate, or
service this heater. Improper use of this heater can
cause serious injury or death from burns, fire, explosion, electrical shock, and carbon monoxide
poisoning.failure to follow instructions may result in
property damage, bodily injury or loss of life. This
manual contains important user information. Keep this
manual with the heater after installation is complete.
FOR SAFE INSTALLATION AND OPERATION,
PLEASE NOTE THE FOLLOWING:
1. Use only Natural Gas with UVS27RN/MN. Use only
Propane with UVS27RP/MP. Do not use any other
fuels.
2. Install only in accordance with the National Fuel
Gas Code, ANSIZ223.1/NFPA54-latest edition.
(Exception: Do not derate this appliance for
altitude. This appliance has been tested and listed
for use in altitudes up to 10,000 feet.)
3. Use only the installation instructions provided by
the manufacturer for this appliance. Installation
and repair should be done by a qualified service
person. The appliance should be inspected before
use and at least annually by a professional service
person. More frequent cleaning may be required
due to excessive lint from carpeting, bedding
material, etc. It is imperative that control compartments, burners and circulating air passageways of
the appliance be kept clean.
4. Warning: Any change to this heater or its controls
can be dangerous. DO NOT make modifications to
any heater or associated parts.
5. DO NOT install this heater in a bedroom or bathroom.
6. Due to high surface temperatures, DO NOT install
this heater
• in a recreational vehicle,
• where curtains, furniture, clothing or other
flammable objects are less than 36 inches from
the front, top or sides of the heater,
• in high traffic areas,
• in windy or drafty areas.
7. DO NOT place clothing or other flammable material on or near the appliance.
8. DO NOT obstruct the top grille at all. Doing so will
cause high levels of carbon monoxide that will
lead to death.
20005004
CARBON MONOXIDE POISONING
MAY LEAD TO DEATH!
Carbon Monoxide Poisoning: Early signs of carbon
monoxide poisoning resemble the flu, with headaches,
dizziness, or nausea. If you have these signs, the heater
may not be working properly. Get fresh air at once! Have
the heater serviced. Some people are more affected by
carbon monoxide than others. These include pregnant
women, people with heart or lung disease or anemia,
those under the influence of alcohol, and those at high
altitudes.
9. This heater needs fresh, outside air ventilation to
operate properly. See Fresh Air Requirements on
pages 6 and 7.
10. If heater shuts off, heater may not have enough
fresh air ventilation. Provide more fresh air. If
heater keeps shutting off, refer to Troubleshooting.
11. DO NOT operate this heater
• where flammable liquids or vapors are used
or stored
• under dusty conditions.
12. The heater becomes very hot when operating.
Alert children and adults to stay away from hot
surfaces to avoid burns or clothing ignition. The
heater will remain hot for a time after shutdown.
Allow surface to cool before touching.
13. Carefully supervise young children when they are
in the room with the heater.
14. Do not use the heater if any part has been exposed to or under water. Immediately call a
qualified service technician to inspect the room
heater and to replace any part of the control
system and any gas control which has been
under water.
15. DO NOT operate the heater if any log is broken or
damaged.
16. Turn heater off and let cool before servicing. Only
a qualified service person should service and
repair heater.
17. DO NOT operate this appliance with the safety
screen removed. If the safety screen is removed
from the appliance for service or cleaning, it must
be replaced before operating the heater.
NOTE: If any of the original wire as supplied with the
appliance must be replaced, it must be replaced with a
wire of at least 105°F temperature rating.
Proposition 65 Warning: Fuels used in gas,
woodburning or oil fired appliances, and the products of
combustion of such fuels, contain chemicals known to the
State of California to cause cancer, birth defects and other
reproductive harm.
California Health & Safety Code Sec. 25249.6
3
Vermont Castings UVS27 Vent-Free Gas Heater
Shell Dimensions
Freestanding Stove
9"
(229mm)
CL
Valve Inlet
26³⁄₄"
(680mm)
Valve Inlet
CL
3"
(76mm)
25"
(635mm)
Drawing Not to Scale
14¹⁄₂"
(368mm)
15⁵⁄₈"
(379mm)
5004
Fig. 1 UVS27 freestanding shell dimensions.
Hearthmount
5"
(140mm)
CL
25¹⁄₄"
(641mm)
Drawing Not to Scale
26¹⁄₂"
(673mm)
16³⁄₈"
(416mm)
5004
Fig. 2 UVS27 Hearthmount specifications.
4
20005004
Vermont Castings UVS27 Vent-Free Gas Heater
Clearance Requirements
A
Minimum Clearances to
Combustible Materials
B
Maintain clearance, (empty space), between combustible materials and the heater as specified below for
the appropriate firebox shell being installed.
Freestanding Stove
C
E
T
D
U
A
B
D
S
C
F
V
G
W
X
H
Y
Z
ST101
Hearthmount
Ref.
A
B
C
D
E
F
G
H
D
A
B
C
ST102
A:
B:
C:
D:
Mantel/Trim* ......................... 35” (889mm) / 2” (51mm)
Side Wall/Trim* ............................................. 2” (51mm)
Rear Wall ........................................................ 0” (0mm)
Max. Mantel Width .................................... 13” (330mm)
Alcove Clearances
B
D
B
ST599a
Mantel
Shelf Depth
13” (330mm)
11¹⁄₄” (286mm)
9³⁄₈” (241mm)
7¹⁄₂” (191mm)
5³⁄₄” (146mm)
4” (102mm)
2¹⁄₄” (57mm)
1” (25mm)
Ref.
S
T
U
V
W
X
Y
Z
Mantel from
Stove Top
35” (889mm)
30” (762mm)
25” (635mm)
20” (508mm)
15” (381mm)
10” (254mm)
5” (127mm)
2” (51mm)
Hearth Requirements
The Freestanding Stove and Hearthmount Shell must
be installed on rigid flooring. If the appliance is installed on any combustible surface other than wood
flooring, such as carpet or tile, a metal or wood panel
must be installed to extend the full length and width of
the unit.
WARNING
A
ST103
C
A:
B:
C:
D:
Ceiling ....................................................... 35” (889mm)
Side Wall ....................................................... 2” (51mm)
Rear Wall ........................................................ 0” (0mm)
Max. Alcove Depth .................................... 13” (330mm)
20005004
• Do not install this heater in a bathroom or
bedroom.
• Installation of this heater must conform with
local codes or, in the absence of local codes, with
the National Fuel Gas Code, ANSI Z223.1 / NFPA54.
• This heater creates warm air currents. These
currents move heat to wall surfaces next to the
heater. Installing the heater next to vinyl or cloth
wall coverings or operating the heater where
impurities in the air such as tobacco smoke exist,
may discolor walls.
• Do not use a blower insert, heat exchanger
insert or other accessory not approved for use
with this heater.
5
Vermont Castings UVS27 Vent-Free Gas Heater
High Elevations
Gas Specifications
Model
Fuel
Gas Control
Max.
Input
BTU/h
UVS27RN
Nat
Millivolt
28,000
19,500
UVS27RP
Prop
Millivolt
28,000
19,500
UVS27MN
Nat
Millivolt
28,000
19,500
UVS27MP
Prop
Millivolt
28,000
19,500
Firebox weight / shipping
Min.
Input
BTU/h
110 lbs.
Gas Inlet and Manifold Pressures
Inlet Minimum
Natural
5.5” w.c.
LP (Propane)
11” w.c.
Inlet Maximum
14” w.c.
14” w.c.
Manifold Pressure
3.5” w.c.
10” w.c. (MP)
11” w.c. (RP)
UVS27R & UVS27M Vent-Free
Certified to:
ANSI Z21.11.2a-2001
Unvented Heaters
The installation of your Vermont Castings stove must
conform with local codes, or in the absence of local
codes, with the National Fuel Gas Code ANSI
Z223.1 - latest edition. (EXCEPTION: Do not derate
this appliance for altitude up to 4,500 feet (1,370m).
Maintain the manifold pressure at 3.5” w.c. for
Natural Gas and 11.0” w.c. for LP Gas.
This appliance may be installed in an
aftermarket* manufactured (mobile)
home, where not prohibited by state or
local codes.
This appliance is to be used only with the
type of gas specified on the rating plate
which is attached to the rear panel. This
appliance is not convertible for use with
other gases.
Input ratings are shown in BTU per hour and are
certified without deration from elevations up to
4,500 feet (1,370m) above sea level.
Nuisance outages may occur at altitudes above
4,500 feet (1,370m) if dirt, dust, lint and/or cobwebs are allowed to accumulate on burner and/or
ODS pilot. Monthly inspection and cleaning is
recommended for altitudes above 4,500 feet
(1,370m)
For elevations above 4,500 feet (1,370m), installations must be in accordance with the current
ANSI Z223.1 and/or local codes having jurisdiction.
WARNING: Improper installation, adjustment, alteration, service or maintenance can
cause injury or property damage. Refer to
this manual for correct installation and
operational procedures. For assistance or
additional information consult a qualified
installer, service agency, or the gas supplier.
Odor During Operation
Neither natural gas nor propane gas give off an odor
when burned. The nature of a vent free combustion
system, however, is such that odors may occasionally be produced during heater operation when
impurities exist in the immediate area. Cleaning
solutions, paint, solvents, cigarette smoke, candles,
adhesives, new carpet or textiles, etc., all can create
fumes. These fumes may mix with combustion air
and can create odor. Such odors will disappear over
time, however the condition can be alleviated by
opening a window or otherwise providing additional
ventilation to the area.
*Aftermarket: Completion of sale, not for purpose of resale, from
the manufacturer.
6
20005004
Vermont Castings UVS27 Vent-Free Gas Heater
Vent Free Features
The UVS27, Model Nos. 3030 thru 3033, is an
unvented gas heating appliance tested and listed to
the ANSI standard Z21.11.2a-2001. This appliance is
specifically configured to burn either Natural Gas or
Propane fuel, as indicated on the metal rating plate
attached to the rear shroud. The UVS27 is not fuel
convertible.
The firebox is shipped fully assembled and ready for
installation with either the Stardance (SUV) or the
Pinnacle (PUV) shell assemblies.
The firebox assembly is composed of the NG or LP
Burner, a base plalte, firebox and screen. The log set,
burner tube, gas valve and pilot comprise the Burner
assembly. (Fig. 1)
The UVS27M is equipped with an SIT control for
manual use only.
The UVS27R is equipped with a Honeywell control
valve that allows thermostatic control, on/off switch or a
remote switch (not supplied).
Both models incorporate variable regulators that allow
you to adjust burner heat output between HIGH,
(28,000 BTU), and LOW, (19,500 BTU). See the
Operation Section for details.
The standing pilot incorporates an Oxygen Depletion
System (ODS/pilot) designed to shut off the appliance if
enough fresh air is not available.
Fresh Air Requirements for Combustion
and Ventilation
WARNING
This heater must have fresh air for proper operation.
If not, poor fuel combustion could result. Read the
following instructions to insure proper fresh air for
this and other fuel-burning appliances in your
home.
Modern construction standards have resulted in homes
that are highly energy-efficient and that allow little heat
loss. Your home needs to breathe, however, and all
fuel-burning appliances within it require fresh air in
order to function properly and safely. Exhaust fans,
clothes dryers, fireplaces, and other fuel burning
appliances all use the air inside the building. If the
available fresh air is insufficient to meet the demands
of these appliances, problems can result.
The UVS27R/M Unvented heater has specific fresh air
requirements. You must determine that these fresh
air requirements will be met within the space where
the appliance will be installed. The following information will help you insure that adequate fresh air is
available for the heater to function properly.
20005004
Provide For Adequate Ventilation
Any space within a home can be classified in the
following categories:
1) Unusually Tight Construction
2) Confined Space
3) Unconfined Space
First, determine which classification defines the
intended space.
Unusually Tight Construction
You must provide additional fresh air if the space falls
into this classification. Unusually Tight Construction is
defined as construction wherein:
a. walls and ceilings exposed to the outside
atmosphere have a continuous water vapor retarder
with a rating of one perm or less with openings
gasketed or sealed and
b. weather stripping has been added on openable
windows and doors and
c. caulking or sealants are applied to areas such as
joints around window and door frames, between sole
plates and floors, between wall-ceiling joints, between
wall panels, at penetrations for plumbing, electrical,
and gas lines, and at other openings.
If your home meets all of the three criteria above, you
must provide supplemental fresh air for the appliance
from outside the home as detailed on page 7, B.
If your home does not meet the above criteria, follow
the procedure below.
Determine if You Have a Confined or
Unconfined Space
Use the following formula to determine if you have a
confined or unconfined space.
Space is defined as the room in which you will install
the heater plus any adjoining rooms with doorless
passageways or ventilation grilles between the rooms.
The National Fuel Gas Code defines a confined space
as a space whose volume is less than 50 cubic feet per
1,000 BTU per hour, (4.8 m3 per kw), of the aggregate
input rating of all appliances installed in that space and
an unconfined space as a space whose volume is not
less than 50 cubic feet per 1,000 BTU per hour, (4.8
m3 per kw), of the aggregate input rating of all appliances installed in that space. Rooms communicating
directly with the space in which the appliances are
installed, through openings not furnished with doors,
are considered a part of the unconfined space.
1. Determine the volume of space, (length x width x
height). Include adjoining rooms connected by doorless
passageways or ventilating grilles.
7
Vermont Castings UVS27 Vent-Free Gas Heater
Example:
A room that is 18' x 12' x 8' has a volume of 1728
cubic feet, ( length x width x height). An adjoining open
kitchen that is 10' x 12' x 8' has a volume of 960 cubic
feet. An adjoining open dining room is 12' x 12' x 8'
with a volume of 1152 cubic feet. The total space
volume is 3840 cubic feet. (1728 + 960 + 1152).
2. Divide the volume of space by 50 cubic feet. The
result is the maximum BTU/Hr that the space can
support.
Example:
3840 divided by 50 = 76.8 or 76,800 BTU/Hr.
3. Add the BTU/Hr ratings of all fuel-burning appliances installed in the same space, including the
following:
Gas Water Heater
Gas Furnace
Gas Fireplace Logs
Unvented Gas Heater
Vented Gas Heater*
Other Gas Appliances*
* Do not include Direct Vent appliances as these
utilize outside air for combustion and vent to the
outdoors.
Example:
Gas Range
55,000 BTU/Hr
Unvented Heater
+33,000 BTU/Hr
Total
88,000 BTU/Hr
4. Compare the maximum BTU/Hr rating the space can
support with the total BTU/Hr used by the appliances.
Example:
76,800 BTU/Hr - max. the space can support
88,000 BTU/Hr - total used by appliances
In this example, the maximum BTU/Hr that the space
can support is less than the total used by the appliances, the space is considered to be Confined space.
Additional air must be provided to meet the requirements of the Unvented heater.
A confined space may be ventilated in two ways:
A) Open up or provide at least two ventilating grilles
to an adjoining unconfined space. Use any of the
options illustrated in Figure 8.
Each of the two grilles must provide an opening of
at least 50 square inches, with all opening dimensions
being at least 3". One grille must be located within 12"
of the ceiling; the other within 12" of the floor. (If the
total exceeds 100,000 BTU/Hr, additional grilles will be
required.)
B) Vent the room directly to the outdoors. (Provide
one square inch of opening for each 4,000 BTU/hr.
If the total BTU/Hr used by the appliances is less than
the maximum BTU/Hr the space is able to support, the
room meets the Unconfined space criteria and no
further ventilation is required.
For further information on ventilation guidelines and
sizing specifications follow the National Fuel Gas Code
NFPA 54/ANSI Z223.1 Section 5.3.
WA R N I N G
This heater shall not be installed in a confined
space or unusually tight construction unless
provisions are made for adequate combustion
and ventilation air.
WA R N I N G
If the area in which the heater may be operated
is smaller than that defined as an unconfined
spaceof if the building is of unusually tight
constructins, provide adequate combustion and
ventilation air by one of the methods described
in the National Fuel Gas Code, ANSI Z223.1,
NFPA 54, Section 5.3 or applicable codes.
12”
Option 1
Vents to
Adjoining
Room
Option 3 Vents to
Adjoining
Room
Option 2 Remove
Door to
Adjoining
Rooms
12”
VO370-2
Fig. 8 Vent options to provide additional air.
8
20005004
Vermont Castings UVS27 Vent-Free Gas Heater
Assembly Procedures
Refer to the specific assembly instructions for the shell
appropriate to your UVS27R or UVS27M Heater
installation.
NOTE: If you intend to hard-plumb the gas supply line
to the burner, you may wish to install the union or elbow
at the burner control valve inlet before installing the
firebox within the shell.
CAUTION
Porcelain enamelled surfaces are fragile. Handle
porcelain enamelled castings tenderly. Familiarize
yourself with the assembly steps before you begin
and proceed with deliberation and care. If possible,
have assistance available.
Place enamelled castings on a soft, cushioned
surface until you are ready to assembly.
Unpack the Firebox
Remove the firebox assembly from the shipping carton
and inspect it for loose or damaged parts. The burner,
firebox and base plate should all be secured as a unit.
Do not install this appliance if any parts are loose or if
there is any visual or suspected damage resulting from
shipping or handling. Report damage to your dealer/
distributor immediately. The log set is packaged in the
box shipped inside the firebox.
To remove the packaged log set from the firebox,
remove the screen frame, remove box and set aside.
Contact your dealer if the burner is loose or damaged
in any way.
Avoid contact between the castings and other hard
surfaces or objects.
Shell / Firebox Assembly
1. Attach the Back Panel to the Left Side Plate by
aligning the key holes in the Shroud with the bolts in
the side. (Fig. 5) Slide the shroud panel downward
to engage it behind the washers on the side plate
and then tighten the upper and lower wingbolt.
2. Attach the Right Side Plate to the Back Panel in a
similar manner. Tighten the upper and lower
wingbolt. (Fig. 6) Move this assembly into the final
position and align the two side plates perpendicular
to the back panel as in Figure 7.
3. The Firebox is completely assembled. The Burner
and Valve assembly require no adjustment. However, be sure to remove the packaged logs from
within the firebox. Remove the screen frame by
lifting up and away from the firebox. Remove the box
of logs from inside the unit and set aside for later log
placement.
Regulator
Valve Control
Piezo Ignitor
ST100
Fig. 4 UVS27 firebox and controls.
Left
Side
Back
Panel
WARNING
Failure to position the parts in accordance with these
diagrams or failure to use only parts specifically
approved for use with this heater may result in
property damage or personal injury.
Wingbolt
ST104
Fig. 5 Secure left side to the back panel.
20005004
9
Vermont Castings UVS27 Vent-Free Gas Heater
5. Lift the firebox assembly as a unit and slide it back
to position it within the shell. The base of the firebox
should rest on the side support shelves as in Figures
7 and 9. The side plates interlock with the firebox by
use of a pair of steel tabs that engage with the ribs
on the base of the firebox. (Fig. 9) Properly positioned, the firebox will be level and locked in place. If
not, adjust the levelling screws as required to keep
the entire assembly level.
Right
Side
Steel Tab
Wingbolt
Side Plate
ST105
Fig. Secure right side to the back panel.
ST105
Screw & Washer Shell assy
4/15/99 djt
Support Shelf
ST125
Fig. 9 Install the firebox assembly,. Be sure steel tabs
engage ribs on base of firebox.
Back Panel
ST125
Install
Optional Fan Kit
Firebox washer align
1. Attach the fan to the firebox by engaging the upper
10/15/99
flange of the fan
skirt underdjt
the lower edge of the
Side
Plate
shroud and secure the skirt with the four screws and
one star washer provided. (Fig. 10, 11)
ST106
2. Feed the snapstat wire lead up between the inner
and outer rear shroud panels and secure the
snapstat to the upper right side of the inner shroud.
(Fig. 12)
Fig. 7 The sides must be at right angles to the back panel in
order for the firebox to fit properly.
3. Secure the snapstat wire harness to the shroud
panel using the wire tie provided.
4. Connect the gas supply line to the burner control
valve before you install the firebox. This may be a
flexible line, (not supplied), or hard plumbing.
4. Route the rheostat control switch and wire forward
under the stove. Use the wire tie to secure the fan
and rheostat wire harnesses together to the tubing
under the bottom heat shield.
1/2” Gas Supply
1/2” NPT x 1/2” Flare Shutoff
Valve
3/8” Flex Line
(from Valve)
5. Install the rheostat onto the bracket to the left of the
valve. (Fig. 13)
FP297a
Fig. 8 Typical gas supply installation.
10
20005004
Vermont Castings UVS27 Vent-Free Gas Heater
BLK
Upper
Flange
BLK
MOTOR
BLK
SNAPSTAT
WHT
GRN
WHT
BLK
ON/OFF
RHEOSTAT
ST344
ST236
Fig. 10 Place upper flange behind lower edge of shroud.
Fig. 14 Fan wiring diagram.
Install ON/OFF Switch
The switch assembly parts are found in the parts bag.
1. Attach switch assembly to left rear side of stove
shroud using two screws and existing holes in
shroud. (Fig. 15)
2. Run wires down back of stove, under bottom of rear
shroud to valve.
3. Attach wires to valve terminals. (Fig. 16)
Switch
Assembly
Existing
Holes
ST345
Fig. 11 Correct position of fan skirt installation.
Screws
ST315
ST346
TPTH
TP
Fig. 12 Attach snapstat to inner shroud.
TH
Fig. 15 Attach switch assembly to rear shroud.
ST228
Fig. 16 Attach switch wires to valve.
Retaining Nut
Rheostat
Control Knob
FK104
Fig. 13 Attach rheostat to bracket.
20005004
11
Vermont Castings UVS27 Vent-Free Gas Heater
Glass & Catalyst Installation
On/Off Switch Wiring
TP/TH
ON
CAUTION: Air shutter on Natural Gas units
must be adjusted when installing glass
and catalyst for proper operation. LP units
do not use an air shutter.
1. Remove screen. (Fig. 18) Remove rear, left and right
log bracket assembly by unfastening the two screws
which hold the burner in place.
Thermopile
Black
OFF
Screen Hooks
TP
Black
TH
ST124b
Optional Thermostat/Remote Wiring
ST713
TP/TH
Fig. 18 Remove screen.
2. Hold the burner at the right hand side and lift to clear
the right burner leg. Then pull to the right to clear the
injectors on the left hand side.
Thermopile
Black
Thermostat/Remote
(Optional)
3. Turn burner upside down and remove air shutter.
Turn air shutter upside down and replace on burner.
(Fig. 19)
TP
TH
Black
ST124c
Fig. 17 ON/OFF switch and optional Thermostat/Remote
wiring.
Thermostat Connection (Optional)
4. Replace burner. Slide the burner in at an angle with
left side lower than the right side. Slide the left side
onto the injectors, making sure the burner leg
remains at a 90° angle to the base. (Fig. 20) Lower
the right hand side down in to place. Make sure the
burner is as far left as possible and the injector
Air Shutter as Shipped from Factory
Use only a thermostat rated for 500 - 750 millivolts.
Do not use low voltage (24V) thermostats.
Check the table below for the appropriate gauge
thermostat wire to use for the length of lead required in
your installation.
Thermostat Wire / Gauge
18
20
22
Maximum Run
40 feet
25 feet
16 feet
Bottom of Burner Pan
Air Shutter Turned Upside Down
1. Install the wall thermostat in the desired location and
run the wires to the stove location. Terminate these
leads with 1/4” female connectors.
2. Connect the thermostat wires to the valve. (Fig. 17)
ST667
Fig. 19 Remove air shutter, turn upside down and replace.
12
20005004
Vermont Castings UVS27 Vent-Free Gas Heater
Connect the Gas Supply Line
Left Burner Leg
Check the Rating Plate attached by a steel cable to the
firebox, to confirm that you have the appropriate firebox
for the type of fuel to be used.
Injector Orifices
The appliance should have a main gas valve provided
in an accessible location for turning on or shutting off
the gas to the main burner.
90¡
ST353a
Fig. 20 Be sure injector orifices remain at 90° to the base.
shoulders are inside the burner.
5. Replace rear, left and right log bracket assembly and
replace logs.
6. Shoulder bolts provided in catalyst kit must be
installed on top of firebox. Use nut to secure in
place. (Fig. 21)
7. Set catalyst on top plate. Secure with two screws
and washers as shown in Figure 21.
8. Install glass frame assembly by resting the bottom
edge of the frame on support brackets below the
front opening of the firebox. Rotate the top edge of
the assembly toward the firebox, and center it.
Fasten by “rotating” the cams over the top left and
right edges of the frame. (Fig. 22)
Shoulder
Bolts
Apply nut
and
washer to
underside
Catalytic Combustor
This appliance should only be connected by a
qualified gas technician. Test to confirm manifold
pressures as specified below.
The UVS27 and its individual shutoff valve must be
disconnected from the gas supply piping during
any pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa).
The UVS27 must be isolated from the gas supply
piping system by closing its individual manual
shutoff valve during any pressure testing of the gas
supply piping system at test pressure equal to or
less than 1/2 psig.
There must be a gas shutoff between the stove and
the supply.
In order to connect Natural Gas, use a fitting with
3/8” NPT nipple on the valve side and 1/2” natural
gas supply line with an input of 28,000 BTUs at a
manifold pressure of 3.5” and minimum inlet supply
for adjustment of 5.5” w.c.
In order to connect Propane, use a fitting with 3/8”
NPT nipple on the valve side and 1/2” propane gas
supply line with an input of 28,000 BTUs at a manifold pressure of 11.0” and minimum inlet supply for
adjustment of 11.0” w.c.
Gas connection should be made in accordance with
current National Fuel Gas Code, ANSI Z223.1. Since
some municipalities have additional local codes, be
sure to consult you local authority.
ST709
Fig. 21 Install shoulder bolts and set catalytic combustor in
place.
Connect the gas supply and test for leaks. Use a 50/50
solution of liquid soap and water to test for leaks at gas
fittings and joints. NEVER test with an open flame.
Light the pilot according to the directions on Psage 17,
before going to the next step.
ST711
Fig. 22 Rotate cams into place to hold glass frame assembly
in place.
20005004
13
Vermont Castings UVS27 Vent-Free Gas Heater
CAUTION
This appliance should only be
connected by a qualified gas technician. Test to confirm manifold
pressures as specified below.
The UVS27 and its individual shutoff valve must
be disconnected from the gas supply piping
during any pressure testing of that system at test
pressures in excess of 1/2 psig (3.5 kPa).
The UVS27 must be isolated from the gas supply
piping system by closing its individual manual
shutoff valve during any pressure testing of the
gas supply piping system at test pressure equal
to or less than 1/2 psig.
4. Install the left log by placing it on the sheet metal
bracket behind the grate with the left end of the log,
“the thicker end” touching the grate and the left end
of the firebox. Lay the log into the recessed area on
the left branch of the rear log. When the log is in
place, it will rest on the left branch of the rear log
toward the left side of the branch.
5. Loosely sprinkle the lava rocks directly on top of the
burner just behind decorative grate. (Fig. 24) Do not
place lava rocks toward back of burner. The lava
rock is shipped inside the bag assembly.
Left Log
Right Log
There must be a gas shutoff between the stove
and the supply.
In order to connect Natural Gas, use a fitting with
1/2” NPT on the valve side and 1/2” natural gas
supply line with an input of 28,000 BTUs at a
manifold pressure of 3.5” between minimum inlet
supply of 5.5” w.c. and maximum of 14.0” w.c.
In order to connect Propane, use a fitting with 1/2”
NPT on the valve side and 1/2” propane gas supply
line with an input of 28,000 BTUs at a manifold
pressure of 11.0” between a minimum inlet supply
of 11.0” w.c. and maximum of 14.0” w.c.
Install Log Set
1. Remove the logs from their packaging, and inspect
each piece for damage. DO NOT INSTALL DAMAGED LOGS.
2. Install the rear log by placing it on the sheet metal
shelf at the back of the firebox. (Fig. 23) The log
should touch the back wall of the firebox and be
centered.
3. Install the right log by placing it on the sheet metal
bracket behind the grate with the right end of the
log, “the thicker end”, touching the grate and the
right side the firebox. Swing the left end of the log
“painted end”, backward until it comes in contact
with the branch on the rear log. Set the log down
over the bent tab on the right. When the log is in
place it rests on the tab mentioned earlier and the
tip of it comes in contact with the branch on the rear
log. (Fig. 23)
Rear Log
LG223
Fig. 23 Install rear, left and right logs.
LG224
Fig. 24 UVS27 logs in place.
14
20005004
Vermont Castings UVS27 Vent-Free Gas Heater
Complete the Installation
1. Install the screen frame by sliding the hooks over the
top front edge of the firebox and resting the bottom
on the support brackets. If the catalyst has been
installed, place the glass front on the stove by
resting the bottom edge of the frame on support
brackets below the front opening of the firebox.
Rotate the top edge of the assembly toward the
firebox, and center it. Rotate the right and left cams
towards the back of the firebox to secure glass
frame in place.
2. Grasp the front plate by the window bars and lift into
position engaging the two steel tabs behind the
adjacent bosses in the side plates. (Fig. 25) then
seat the front against the sides so the tabs at the
bottom lip engage with the notches in the stove legs.
ST113
Bottom Tabs engage notch
in the base.
Fig. 26 Engage the Hearthmount Front with the notch in the
bse of each side plate.
Engage steel tabs
behind the cast
iron bosses
3. Tilt the top plate to engage its rear rib in front of the
back panel, then carefully lower it onto the sides.
(Fig. 27) The upper edge of the side plates should
seat into the channel in the underside of the top.
4. Lay the screen and top grille in place.
This completes assembly of the Stardance Freestanding and Pinnacle Hearthmount shells.
Grille
Screen
Control Door
Top Plate
Bottom Tabs engage
notch in the leg.
ST112
Fig. 25 Install the Front Plate. Your Front may look different
from that shown.
On the Pinnacle, the front tabs will engage behind the
notched cutouts in the base of either side plate. (Fig.
26)
When properly installed, the bottom of the front plate
cannot be pulled away form the sides without lifting it.
NOTE: Be sure that the control door can swing out. It
should close against the steel tab stop.
If installing the optional warming shelf, you may find it
easiest to attach it to the top plate before placing the
top in position on the stove. Follow the instructions
supplied with the kit.
20005004
Levelling
Screws
ST114
Fig. 27 Install the Top Plate and Grille.
15
Vermont Castings UVS27 Vent-Free Gas Heater
Operation
Each time you light your heater check that the pilot
flame and burner flame patterns are as shown in
Figures 31 and 32. If flame patterns are incorrect, turn
the heater off. Contact your dealer or a qualified gas
technician for assistance. Do not operate the heater
until the pilot flame is correct.
Follow regular maintenance procedures as described
on Page 20.
Turn clockwise
to increase
flame height
HV102
Fig. 29 Flame adjustment knob for Honeywell Valve.
SIT 630
Turn
counterclockwise
to increase
flame height
LO
PIL
OT
Pilot and Burner Inspection
HI
HI
During the first fire, it is not unusual to smell some odor
associated with new logs, paint and metal being
heated. Odors should dissipate within the first eight to
ten hours, however, you can open a window to provide
fresh air to alleviate the condition.
Turn
counterclockwise
to decrease
flame height
OFF
Read these instructions carefully and familiarize
yourself with the burner controls shown on Page 18.
Locate the pilot assembly, Figure 28. Follow the
lighting instructions on Page 17 exactly.
LO
Your First Fire
Turn clockwise
to decrease
flame height
HV117
Fig. 30 Flame adjustment knob for Eurosit Valve.
Flame Characteristics
It is important to periodically perform a visual check of
the pilot and burner flames. Compare them to the
pictorial illustrated below. (Fig. 31, 32) If the flame
patterns appear abnormal contact a qualified service
provider for service and adjustment.
Natural
Pilot
ST198
Fig. 31 Correct pilot flame appearance.
LP Pilot
ST673
Fig. 28 Pilot assembly location.
Flame & Temperature Adjustment
RN/RP Models
For units equipped with ‘HI/LO’ valves the flame
adjustment is accomplished by rotating the ‘HI/LO’
adjustment knob located near the center of the gas
control valve. (Fig. 29, 30)
LG225
Fig. 32 Correct burner flame pattern.
16
20005004
Vermont Castings UVS27 Vent-Free Gas Heater
Lighting and Operating Instructions
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING:If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
A. This heater has a pilot which must be lit manually.
When lighting the pilot follow these
instructions exactly.
B. BEFORE LIGHTING smell all around the heater
area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any fireplace
• Do not touch any electric switch
• Do not use any phone in your building
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
•
If you cannot reach your gas supplier, call the
Fire Department
C. Use only your hand to push in or turn the gas
control knob. Never use tools. If the knob will not
push in or turn by hand, do not try to repair it, call a
qualified service technician. Applying force or any
attempted repair may result in a fire or explosion.
D. Do not use this fireplace if any part has been under
water. Immediately call a qualified service technician to inspect the heater and to replace any part of
the control system and any gas control which has
been under water.
Lighting Instructions
1. STOP! Read the safety information above.
2. Turn off all electrical power to the fireplace.
3. For MN/MP/TN/TP appliances ONLY, go on to
Step 4. For RN/RP appliances turn the On/Off
switch to “OFF” position or set thermostat to
lowest level.
4. Open control access panel.
5. Push in gas control knob slightly and turn clockto "OFF".
wise
T
LO
ON
OFF
P
OFF ilot
3/8" - 1/2"
OFF
PI
ON
1 2
3 4 5
Euro SIT
OFF
PILOT
10. Push the control knob all the way in and hold.
Immediately light the pilot by repeatedly depressing the piezo spark ignitor until a flame appears.
Continue to hold the control knob in for about one
(1) minute after the pilot is lit. Release knob and it
will pop back up. Pilot should remain lit. If it goes
out, repeat steps 5 through 8.
SIT NOVA
Honeywell
6. Wait five (5) minutes to clear out any gas. Then
smell for gas, including near the floor. If you
smell gas, STOP! Follow "B" in the safety
information above. If you do not smell gas, go
to the next step.
7. Remove glass door before lighting pilot. (See
Glass Frame Removal section).
8. Visibly locate pilot by the main burner.
9. Turn knob on gas control counterclockwise
to "PILOT".
•
If knob does not pop up when released, stop
and immediately call your service technician or
gas supplier.
•
If after several tries, the pilot will not stay lit,
turn the gas control knob to "OFF" and call your
service technician or gas supplier.
11. Replace glass door.
12. Turn gas control knob to “ON” position.
13. For RN/RP appliances turn the On/Off switch to
“ON” position or set thermostat to desired setting.
14. Turn on all electrical power to the fireplace.
To Turn Off Gas To Heater
1. Turn the On/Off switch to Off position or set the
thermostat to lowest setting. (R Models only)
2. Turn off all electric power to the fireplace if
service is to be performed.
20005004
3. Open control access panel.
4. Push in gas control knob slightly and turn
clockwise
to "OFF". Do not force.
5. Close control access panel.
17
Vermont Castings UVS27 Vent-Free Gas Heater
Troubleshooting
Follow these procedures in the order presented.
WA R N I N G
TURN OFF HEATER AND ALLOW TO COOL
COMPLETELY BEFORE SERVICING.
CONDITION
POSSIBLE CAUSE
SOLUTION
No spark at pilot when Ignitor is
operated.
1. Ignition Electrode is disconnected
from ignition wire, broken or
incorrectly positioned.
2. Ignitor wire is broken.
3. Bad Piezo Ignitor.
1. Inspect and re-connect, replace
or repair as necessary.
1. Gas supply is turned off or supply
line shut-off valve is closed.
2. Control Knob is not in PILOT
position.
3. Control Knob not pressed in while
in PILOT position.
4. Air present in gas lines.
1. Turn on gas supply or open
supply line shut-off valve.
2. Turn Control Knob to PILOT.
The Ignitor Electrode sparks,
but Pilot does not light.
5. Inlet supply pressure is not within
correct settings.
6. Other conditions that should be
identified only by a qualified gas
technician.
2. Replace wire.
3. Replace Piezo Ignitor.
3. Press Control Knob in while in
the PILOT position.
4. Continue holding in Control Knob
and repeat ignition procedure
until air is bled from the lines.
5. Call local gas supplier. Adjust
inlet supply pressure to specification: NG; 5.5” w.c.-14.0”w.c. LP;
11.0” w.c.-14.0”w.c.
6. Call qualified gas technician.
TH
Piezo Ignitor
TP
O H
PILOT
ADJ
TPTH
ON
L
I
PI
LO
T
OFF
Regulator
HV104
Pilot / Main Control
Fig. 33 Honeywell valve assembly.
18
20005004
Vermont Castings UVS27 Vent-Free Gas Heater
Troubleshooting cont’d.
CONDITION
POSSIBLE CAUSE
SOLUTION
Pilot lights but flame goes out
when Control Knob is released.
1. Control Knob not fully depressed
or held in long enough.
2. Gas supply line shut-off valve is
not fully open.
3. Thermocouple connection is
loose at the Control Valve.
1. Depress Control Knob fully and
hold in for a full 30 seconds.
4. Pilot flame does not touch the
Thermocouple. (Figs. 29, 30)
This can be caused by:
A) Incorrect gas pressure, and/or
B) other conditions that should
be identified only by a qualified
service technician.
4. A) Call local gas supplier. Adjust
inlet supply pressure to specification: NG; 5.5” w.c.-14.0”w.c. LP;
11.0” w.c.-14.0”w.c.
B)Call local gas service technician.
5. Thermocouple is damaged.
6. Control Valve is damaged.
5. Call local gas service technician.
6. Call local gas service technician.
Pilot flame is lifting.
Thermopile
Thermocouple
2. Fully open gas supply line shutoff valve.
3. Inspect and tighten securely.
ST121a
Pilot flame is weak - does not touch
Thermocouple.
Correct LP Pilot Flame.
Correct NG Pilot Flame.
Pilot lights but Main Burner does
not.
1. Gas supply line shut-off valve is
not fully open.
2. Foreign material is blocking
Burner ports.
3. Main Burner orifice is clogged.
4. Thermostat or remote switch not
activated on JUVS.
5. Bad Thermopile.
1. Fully open gas supply line shutoff valve.
2. Insptect and clear debris away
from Burner ports.
3. Call local gas service technician.
4. Set thermostat to higher temperature or check remote switch.
5. Call local gas service technician.
Main Burner shuts off and Pilot
flame goes out while in operation.
1. Insufficient fresh air.
1. Determine that adequate ventilation exists to provide sufficient
fresh air. Open a window or
provide additional ventilation.
(See Fresh Air Requirements,
Pages 6-7)
2. Call local gas supplier. Adjust
inlet supply pressure to specification: NG; 5.5” w.c.-14.0”w.c. LP;
11.0” w.c.-14.0”w.c.
2. Incorrect inlet supply pressure.
20005004
19
Vermont Castings UVS27 Vent-Free Gas Heater
Maintenance
The following procedures will help ensure that your
heater continues to perform safely and efficiently.
Screen Hooks
Firebox Cleaning and Inspection
Cleanliness is critical to correct operation of the
heater. The log set, burner, valve controls and air
circulation areas must all be kept free of dust and
unobstructed by debris. Inspect these areas before
each use and clean whenever accumulation is
evident. Follow the simple procedure outlined below.
Frequent cleaning may be necessary in living environments subject to excessive carpet lint or pet hair. For
example, if you live with a dog that sheds continuously,
you will need to inspect the burner area frequently and
clean it as often as the accumulation requires. In
extreme conditions, it may be necessary to clean
the burner and log set monthly or bi-weekly.
This appliance should be inspected and thoroughly
cleaned annually by a qualified gas technician.
Cleaning Procedure
Glass Latch
ST712
Fig. 34 Remove the screen or glass panel.
Glass Replacement
If so equipped, do not operate this appliance with the
glass panel cracked, broken, or removed. Replace
damaged glass only with an approved ceramic glass
panel. Follow the Cleaning Procedure instructions
regarding parts removal.
1. Turn the burner OFF and let the heater cool completely before cleaning.
Care of Cast Iron
2. Lift the Front plate up and then swing the bottom
out to disengage it from the heater shell. (Fig. 25,
Page 15)
An occasional dusting with a dry rag will help keep the
painted surfaces looking new. Use high-temperature
stove paints, available through your local dealer, to
touch-up areas as needed. Clean areas to be painted
with a wire brush and be sure to cover the log set,
burner and valve assembly. Apply the paint sparingly;
two light coats of paint will give better results than a
single heavy coat.
3. Remove the screen by lifting up and away from the
unit. Or, if so equipped, remove the glass panel by
rotating the two cams toward the front of the firebox.
Lift the panel up and off of the firebox frame. (Fig.
34)
4. Carefully inspect the log set for damage. Contact
your local dealer if any damage is evident. DO NOT
OPERATE THE HEATER WITH A DAMAGED OR
LOOSE LOG SET.
Use a soft-bristled brush vacuum cleaner attachment to remove dust or debris from the log set, pilot
and burner. Use care as the log set is fragile.
5. Inspect the catalytic combustor at the top of the
firebox. Replace the combustor if any damage or
deterioration is evident.
6. Replace the screen or glass panel and the front
plate. DO NOT OPERATE THE HEATER WITH
THE SCREEN / GLASS PANEL OR FRONT
PLATE REMOVED.
20
Porcelain enamel surfaces should be cleaned with
a soft, damp cloth. Do not use abrasive cleaning
agents. If necessary, use only a cleaning agent formulated specifically for use on porcelain enamel surfaces.
WARNING
Turn the burner Pilot OFF before applying
paint. NEVER paint pilot or around pilot area.
WARNING
Dust and debris accumulation can result in
poor performance. Inspect the Valve
compartment, burner parts and log set
frequently and Clean these parts monthly or as
often as accumulation warrants.
20005004
Vermont Castings UVS27 Vent-Free Gas Heater
Catalytic Combustor
The combustor should be cleaned annually to ensure
optimal performance. Follow the procedure below.
Remove the Combustor Module
1. Be sure the heater is COLD.
2. Remove the top grille, screen and top plate. (Fig. 35)
3. Use the phillips screwdriver to remove the two sheet
metal screws and washers that secure the combustor to the top of the firebox. (Fig. 36)
Clean the Combustor Module
1. Clean the outer surface of the filter with the brush
attachment of your vacuum cleaner to remove loose
dirt.
ST114a
Fig. 35 Remove top plate, grille and screen.
2. Submerge the filter in a mild soapy water solution.
Rinse thoroughly with distilled water.
3. Replace in heater when dry.
Replace The Combustor Module
1. Set combustor on top of flat surface of firebox.
Secure with the two sheet metal screws and washers.
2. Replace the top plate, screen and grille.
ST709a
Fig. 36 Remove the catalytic combustor module.
20005004
21
Vermont Castings UVS27 Vent-Free Gas Heater
8
7
1a
2a,b
6
5
1b
1d
4
3
1c
10a
10b
PILOT
ADJ
12
ON
TPTH
O H
I
L
13
OT
PIL
TP
11
OFF
TH
10c
9a,b
10d
HI
OFF
OT
PIL
LO
17
9c,d
26
25
14a,b
16a,b,c,d
15
22
23
18
24
21
31
30
33
32
27
19
28
20
5004
UVS27
parts
5004
CFM Specialty Home Products reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products
at any time, without notice.
UVS27R, UVS27M Vent Free Gas Heaters
Models 3030, 3031, 3032, 3033
Ref.
1.
1a.
1b.
1c.
1d.
22
Description
Gas Log Assembly - UVS27
Log #V40 Rear UVS27
Log #V42 Left UVS27
Log #V41 Right UVS27
Lava Rocks Burner
UVS27
20005005
20005006
20005008
20005007
57897
20005004
Vermont Castings UVS27 Vent-Free Gas Heater
UVS27R, UVS27M Vent Free Gas Heaters
Models 3030, 3031, 3032, 3033 (continued)
Ref.
2a.
2b.
3.
4.
5.
6.
7.
8.
9a.
9b.
9c.
9d.
10a.
10b.
10c.
10d.
11.
12.
13.
14a.
14b.
15.
16a.
16b.
16c.
16d.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
Description
Manifold Assy. - UVS27R
Manifold Assy. - UVS27M
Damper Steel Handle/Screw (Stardance Operable Door Only)
Handle Package, Ceramic w/Screw (Stardance Operable Door Only)
Trim ON/OFF Switch
Screen UVS27
Glass Frame Assembly - SDV30
Glass w/Gasket (Comes with UVGDCFK)
Valve NG Honeywell - VS84212003
Valve LP Honeywell - VS84212011
Valve MN Eurosit 0.630.564
Valve MP Eurosit 0.630.563
Oxygenerator, NG OP #8204
Oxygenerator, LP OP #8404
Oxygenerator, NG OP #8202
Pilot ODS TP OP #8402
Front, Stardance OP DR (Stardance Only)
Door, Left - Stardance
Door, Right - Stardance
Burner Housing Assy. - JUV NG
Burner Housing Assy. - LP
Bracket, Rear Log - JUV
Orifice Hood #69 (.0292”) - Front - LP
Orifice Hood #54 (.055”) - Front - NG
Orifice Hood #54 (.055”) - Rear - LP
Orifice Hood #44 (.086”) - Rear - NG
Ignitor Piezo - Honeywell #396079
Gasket, Base Pan Inner
Bracket Support Right Log
Bracket Support Left Log
Grate Decorative Burner
Grille, UV30
Mesh, Grille - UV30
Top, Stardance UV/PDV
Front, Stardance
Front, HM-VC
Door, Control - FS/HM
Cover, Valve w/Piezo
Catalyst, RUV (not shown) (Comes with UVGDCFK)
20005004
UVS27
20003739
20004935
5004265
0004342
53606
20005009
30000127
30000523
10000235
10000242
20001354
20001355
55464
55465
20004435
20001357
Refer to Enamel Parts Chart Page 24
Refer to Enamel Parts Chart Page 24
Refer to Enamel Parts Chart Page 24
20003130
20004995
20003274
30000513
20000130
20000130
30000334
20000062
20002566
20004920
20005022
20003022
30000393
30000508
Refer to Enamel Parts Chart Page 24
Refer to Enamel Parts Chart Page 24
Refer to Enamel Parts Chart Page 24
Refer to Enamel Parts Chart Page 24
51851
30000506
23
Vermont Castings UVS27 Vent-Free Gas Heater
UVS27R, UVS27M Vent Free Gas Heaters
Models 3030, 3031, 3032, 3033 (continued)
Shell Enamel Part Numbers - Hearthmount
Color
Top
Left End
Classic
1301083
30001282
Sand
1321083
30001303
Midnight
1341083
30001310
Right End
30001281
30001302
30001309
Shell Enamel Part Numbers - Freestanding
Color
Top
Left End
Right End
Classic
30001278
30001280
30001287
Red
30001285
30001287
30001286
Sand
30001299
30001301
30001300
Midnight
30001306
30001308
30001307
Green
30001292
30001294
30001293
Moonlight
30001319
30001321
30001320
24
Front
1301129
1321129
1341129
Front (Solid)
30001350
30001351
30001352
30001353
30001354
30001355
Control Door
1301087
1321087
1341087
Front (OP)
30001496
30001261
30001267
30001270
30001264
30001314
Left Door
30001139
30001263
30001269
30001272
30001266
30001316
Right Door
30001138
30001262
30001268
30001271
30001265
30001315
20005004
Vermont Castings UVS27 Vent-Free Gas Heater
Optional Accessories Available
Fan Kits
FK28 Fan Assembly
The FK28 fan kit helps distribute heated air from within
the firebox out into the room. The fan is controlled by a
snapstat that turns power on and off as the firebox
temperature rises above and falls below a preset
temperature. A rheostat provides for variable fan
speeds.
Specifications
Remote Controls
The remote control allows you to turn the heater on or
off from anywhere in the room. Remote controls are
available for the UVS27R only. Refer to Figure 17,
Page 12 for wiring diagram.
Model
Function/s Controlled
MRC1
MRC2
MRC3
ON/OFF
ON/OFF and Temperature
ON/OFF and Temperature control
with a digital display and a pro
grammable 24 hour clock
Wall mounted thermostat control
115 Volt / 60Hz / .75 Amps
Maintenance
The fan itself does not require regular maintenance,
however periodic cleaning of the fan and the surrounding area is required.
Installation
Refer to Assembly Section, Page 10 for installation
instructions.
Glass / Catalyst Kit UVGODCFK
The glass panel replaces the standard screen. The
catalytic combustor installs easily into the upper manifold above the firebox.
IMT
Warming Shelf
Warming shelves add versatility to your stove. The
warming shelf can be used to keep foods warm at
mealtime.
Model
Pinnacle Stardance
Shell
Shell
2702
n/a
n/a
n/a
2764
2765
2702
2704
2706
2711
2764
2765
Color
Classic Black
Red
Green
Moonlight Blue
Sand
Midnight
The shelf installation is done in three stages. First you
attach the shelf loosely to the stove, leaving the screws
loose enough to allow final adjustments. Then, you
position the shelf and adjust the brackets so the shelf
fits correctly. Finally, you tighten the screws.
Refer to the instructions included with each warming
shelf for complete installation procedures.
20005004
25
Vermont Castings UVS27 Vent-Free Gas Heater
LIMITED LIFETIME WARRANTY
PRODUCT COVERED BY THIS WARRANTY
All Vermont Castings gas stoves, gas inserts, and gas fireplaces, and all Majestic or Northern Flame
brand gas fireplaces equipped with an Insta-Flame Ceramic Burner, or standard steel tube burner.
BASIC WARRANTY
CFM Specialty Home Products (hereinafter referred to collectively as
the Company) warrants that your new Vermont Castings or Majestic
Gas Fireplace/Stove is free from manufacturing and material defects
for a period of one year from the date of purchase, subject to the
following conditions and limitations.
EXTENDED LIFETIME WARRANTY
The heat exchanger, where applicable, and combustion chamber of
every Vermont Castings or Majestic gas product is warranted for life
against through wall perforation. All appliances equipped with an InstaFlame Ceramic Burner have limited lifetime coverage on the ceramic
burner plaque. Warrantees are made to the original owner subject to
proof of purchase and the conditions and limitations listed on this
Warranty Document
•
•
•
•
COMPONENT WARRANTY
CAST IRON: All external and internal cast iron parts are warranted for a
period of three years.
Note: On porcelain enamel finished external parts and accessories
The Company offers no Warranty on chipping of enamel surfaces.
Inspect all product prior to accepting it for any damage to the
enamel.
The salt air environment of coastal areas or a high humidity
environment can be corrosive to the porcelain enamel finish. These
conditions can cause rusting of the cast iron beneath the porcelain
enamel finish, which will cause the finish to flake off.
Dye lot variations with replacement parts and/or accessories can
occur and are not covered by warranty.
GLASS DOORS: Glass doors are covered for a period of one year.
Glass doors are not warranted for breakage due to misuse or accident.
Glass doors are not covered for discoloration or burned in stains due to
environmental issues, or improper cleaning and maintenance.
BRASS PLATED PARTS AND ACCESSORIES: Brass parts should be
cleaned with Lemon oil only. Brass cleaners cannot be used. Mortar
mix and masonry cleaners may corrode the brass finish. The Company
will not be responsible for, nor will it warrant any brass parts which are
damaged by external chemicals or down draft conditions.
•
•
•
•
•
•
GAS VALVES: Gas valves are covered for a period of one year
ELECTRONIC AND MECHANICAL COMPONENTS: Electronic and
mechanical components of the burner assembly are covered for one
year. All steel tube burners are warranted for one year.
ACCESSORIES: Unless otherwise noted all components and CFM
Specialty Home Products company supplied accessories are covered
for a period of one year.
CONDITIONS AND LIMITATIONS
•
•
•
•
This new Vermont Castings or Majestic product must be installed by a
competent, authorized, service contractor. A licensed technician, as
prescribed by the local jurisdiction must perform any installation/
service work. It must be installed and operated at all times in accordance
with the Installation and Operating instructions furnished with the
product. Any alteration, willful abuse, accident, or misuse of the product
shall nullify this warranty.
This warranty is non-transferable, and is made to the original owner,
provided that the purchase was made through an authorized supplier
of the Company.
The customer must pay for any Authorized Dealer in-home travel fees
or service charges for in-home repair work. It is the dealers option
whether the repair work will be done in the customer’s home or in the
dealer’s shop.
If upon inspection, the damage is found to be the fault of the manufacturer,
repairs will be authorized at no charge to the customer parts and/or
labor.
•
Any part and/or component replaced under the provisions of this
warranty is covered for six months or the remainder of the original
warranty, whichever is longest.
This warranty is limited to the repair of or replacement of part(s) found
to be defective in material or workmanship, provided that such part(s)
have been subjected to normal conditions of use and service, after said
defect is confirmed by the Company’s inspection.
The company may, at its discretion, fully discharge all obligations with
respect to this warranty by refunding the wholesale price of the
defective part(s)
Any installation, labor, construction, transportation, or other related
costs/expenses arising from defective part(s), repair, replacement, or
otherwise of same, will not be covered by this warranty, nor shall the
Company assume responsibility for same. Further, the Company will
not be responsible for any incidental, indirect, or consequential damages
except as provided by law.
SOME STATES DO NOT ALLOW FOR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS,
SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOUR
CIRCUMSTANCES. THIS WARRANTY GIVES YOU SPECIFIC
RIGHTS AND YOU MAY HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
All other warranties-expressed or implied- with respect to the product,
its components and accessories, or any obligations/liabilities on the
part of the Company are hereby expressly excluded.
The Company neither assumes, nor authorizes any third party to
assume on its behalf, any other liabilities with respect to the sale of this
Vermont Castings or Majestic product
The warranties as outlined within this document do not apply to
chimney components or other non CFM Specialty Home Products
accessories used in conjunction with the installation of this product..
Damage to the unit while in transit is not covered by this warranty but
is subject to claim against the common carrier. Contact the dealer from
whom you purchased your fireplace/stove (do not operate the appliance
as this might negate the ability to process the claim with the carrier).
The Company will not be responsible for:
a) Down drafts or spillage caused by environmental conditions such
as near-by trees, buildings, roof tops, hills, or mountains.
b) Inadequate ventilation or negative air pressure caused by
mechanical systems such as furnaces, fans, clothes dryers, etc.
This warranty is void if:
a) The fireplace has been operated in atmospheres contaminated by
chlorine, fluorine, or other damaging chemicals.
b) The fireplace has been subjected to prolonged periods of dampness
or condensation
c) Any damages to the fireplace, combustion chamber, heat exchanger
or other components due to water, or weather damage, which is the
result of but not limited to, improper chimney/venting installation.
d) Any alteration, willful abuse, accident, or misuse of the product has
occurred.
IF WARRANTY SERVICE IS NEEDED…
1) Contact your supplier. Make sure you have
your warranty, your sales receipt, and the
model/serial number of your CFM Specialty
Home Products product.
2) DO NOT ATTEMPT TO DO ANY SERVICE
WORK YOURSELF.
© CFM Specialty Home Products
26
20005004
Download PDF

advertising