Ford SK5W7J-19A361-AA Remote Starter User Manual

SK5W7J-19A361-AA
INSTALLATION AND TECHNICAL
REFERENCE MANUAL
WARNING! REMOTE START SYSTEMS ARE ONLY
APPLICABLE TO VEHICLES WITH AUTOMATIC
TRANSMISSION!
BOTH ORIGINAL KEYS ARE REQUIRED FOR ALL
REMOTE START SYSTEMS ON VEHICLES EQUIPPED
WITH SECURILOCK!
EXPERT FITMENT REQUIRED
Subject to Change Without Notice
ALL MODELS 2002
Use Caution Personal Injury
Use Caution Vehicle Damage
Technical Support
See shop manual
(800) FORD-KEY
For French Technical Support
Rock Hebert (514) 973-2846
!
Important note
S
RU ILICO
BB NE
ER
TOOLS REQUIRED
Silicone sealer
D6AZ-19562-AA
9/32”
8mm
7mm
Super Seal
F3AZ-19515-SA
1/4”
101871-2
1/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
TABLE OF CONTENTS
READ ME FIRST ........................................................................................................... 3
KIT CONTENTS ................................................................................................................................... 4
PARTS BAG CONTENTS .................................................................................................................... 5
KIT BILL OF MATERIALS LISTS ........................................................................................................ 6
MODULE PREPARATION ................................................................................................................... 9
VEHICLE PREPARATION ................................................................................................................. 11
DIPOLE ANTENNA MOUNTING ....................................................................................................... 12
STATUS LED ..................................................................................................................................... 13
SECURILOCK INTERFACE KITS - 1L2Z-19G365-AB & 1S4Z-19G365-AB .................................... 14
SECURILOCK INTERFACE KIT - 1L3Z-19G365-AB ....................................................................... 17
SIREN INSTALLATION ..................................................................................................................... 18
HOOD TILT SWITCH INSTALLATION .............................................................................................. 19
MOUNTING THE CONTROL MODULE ............................................................................................ 20
SYSTEM WIRING CONNECTIONS ................................................................................................... 21
WARNING LABEL INSTALLATION .................................................................................................. 21
SYSTEM PROGRAMMING INSTRUCTIONS .................................................................................... 22
TRANSMITTER PROGRAMMING: .............................................................................................. 22
OPTION PROGRAMMING: .......................................................................................................... 22
SHOCK SENSOR SETTING ........................................................................................................ 23
TACH (IDLE SPEED) PROGRAMMING ...................................................................................... 24
REFERENCE SECTION ............................................................................................ 26
SECURILOCK INTERFACE AND RELAY APPLICATION CHART .................................................. 26
OPTION PROGRAMMING CHARTS ................................................................................................. 29
RKE/VSS/RMST OPTION CHART .............................................................................................. 29
RKE/RMST OPTION CHART ....................................................................................................... 31
RMST OPTION CHART ............................................................................................................... 33
DELUXE RKE/VSS OPTION CHART .......................................................................................... 34
RKE/VSS & VSS OPTION CHART .............................................................................................. 35
RKE OPTION CHART .................................................................................................................. 36
LOT MODE ONLY OPTION CHART ............................................................................................ 37
WIRING HARNESS LEGEND ........................................................................................................... 38
CIRCUIT TESTING - IDENTIFYING CIRCUIT POLARITY ................................................................ 39
WIRE CONNECTION PROCEDURES .............................................................................................. 40
VEHICLE SPECIFIC WIRING DIAGRAMS ............................................................... 42
2/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
READ ME FIRST
For convenience this document uses short names when referring to a particular system or kit. The list below identifies the
short names used herein:
Remote Start System with Deluxe Vehicle Security and Keyless Entry —> RKE/VSS/RMST
Remote Start System with Keyless Entry —> RKE/RMST
Remote Start System —> RMST
Deluxe Vehicle Security System with Keyless Entry —> Deluxe RKE/VSS
Vehicle Security System with Keyless Entry —> RKE/VSS
Vehicle Security System for Vehicles Equipped with Factory Keyless Entry —> VSS
Keyless Entry System —> RKE
buttons in the Acrobat toolbar, 2) clicking on the
Navigating this document can be accomplished by: 1) using the
bookmark links in the bookmark pane to the left. (Clicking on the (+) symbols next to a bookmark will expand that bookmark,
revealing additional selections) or 3) clicking on a topic in the table of contents located on page 2.
The most current version of this document can be accessed at www.mcdistributor.com and/or www.fmcdealer.com. As new/
updated material becomes available, this document will be updated and posted on those sites.
This installation instruction covers the installation of all PowerCode based Convenience/Security and Remote start kits,
therefore follow only the steps that apply to the kit that you are installing. For example, the Securilock interface kits are only
used on systems that include remote start (RMST). Therefore, if you are installing a security only kit, skip the steps pertaining
to the Securilock interface kit.
Vehicle wiring is subject to change. All possible efforts have been taken to ensure that the information contained herein is
accurate as of the revision dates indicated. As such, it is critical that vehicle circuits are tested prior to making any
connections, to ensure that the proper vehicle circuit has been located.
Prior to beginning this installation it is recommended that you lower the drivers door window to prevent locking the keys in the
vehicle.
The installation instructions are presented in three sections. The first section (which begins immediately following this page)
contains installation instructions for the systems various components and tips for prepping the systems wiring harnesses.
These steps are presented in a generic format. The procedures for these installation steps are basically the same regardless
of the model vehicle or system that you are working on. The drawings depicted in this section are for reference only and may
not reflect the vehicle on which you may be working.
The second (reference) section contains the system option programming charts and various other reference type information.
The last section presents vehicle specific wiring diagrams for each application. Within the wiring section for each vehicle,
there are separate wiring diagrams for each different system. The vehicle specific wiring drawings are arranged in the
following order:
1. RKE/VSS/RMST & RKE/RMST (in the same drawing) - Typically 4 pages;
2. RMST - 1 page
3. Deluxe RKE/VSS - 3 - 4 pages;
4. RKE/VSS & RKE installation options - 1 page;
5. VSS - Typically 1 page;
6. Pre-load system wiring - 1 page;
7. Fuse placement and vehicle specific programming requirements - 1 page.
Vehicles that are equipped with 100% factory keyless entry will not have the RKE/VSS & RKE drawing. Some drawings will
have blank pages inserted to maintain the page order.
Prior to beginning your first installation of this product it is recommended that you:
1. Thoroughly review and print out the first section;
2. Skim through the reference section to become acquainted with the additional information that is available.
Then, when going through the installation print out the vehicle specific wiring section and use as a reference during the
installation.
3/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
KIT CONTENTS
A
B
PC-12 - 2W7J-19A498-AA
PC-32 - 2W7J-19G367-AA
E
C
SEE KIT BOM
F
I
G
J
H
K
N
2W7J-15K601-BA
2W7J15603-AA
2W7J-19A206-AA
2W7J-19A205-AA
M
2W7J-15K601-BA
2W7J-15K601-AA
2W7J-15K601-AA
D
N/A
L
2W7-J12060-AA
O
N/A
P
WARNING: / AVERTISSEMENT
This vehicle is equipped with a remote controlled engine starter.
To reduce the risk of serious Injury or death, switch engine starter
system into service mode and disconnect the vehicle battery
before performing any service on the vehicle.
Ce véhicule est doté d'un démarreur à distance. Pour réduire les
risques de blessures graves ou mortelles, mettre le démarreur à
distance en mode service et débrancher la batterie du véhicule
avant d'effectuer des travaux d'entretien sur celui-ci.
2W7J-15W593-AA
2W7J-19G366-AA
Q
N/A
N/A
R
Vehicle Security and Remote Start Systems
Remote Start System with Deluxe Vehicle Security
Sistema de encendido por control remoto y seguridad para vehículos de lujo
Système de démarrage à distance avec antivol de voiture de luxe
2 sec.
Owner's Manual
Manual del propietario
Guide de l’utilisateur
5X
2 sec.
30
sec.
Featuring PowerCode Technology
TM
N/A
4/42
FortheUltimateinComfort,ConvenienceandSecurity
N/A
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
PARTS BAG CONTENTS
S
T
750 OHM
U
V
1800 OHM
1X
W
X
Y
2X
AA
2X
1X
Z
10X
5X
BB
6X
1X
DD
CC
15A
5A
2X
7X
1X
PC-12 - 4X
PC-32 - 7X
NOTE: Part bag contents are not available as
service items
5/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
KIT BILL OF MATERIALS LISTS
2W7Z-19G364-AA
Remote Start System w/Deluxe Vehicle Security and Keyless Entry Kit
(RKE/VSS/RMST)
REF
A
B
C
I
J
K
L
G
M
N
S - BB
CC, DD
R
S
O
P
DESCRIPTION
PC-32 MODULE ASSEMBLY
RKE/VSS/RMST DNA ASSEMBLY (2W7J-19G367-BA)
4 BUTTON POWERCODE TRANSMITTER W/REMOTE START ICONS
24-WAY WIRING HARNESS (BASE)
16-WAY WIRING HARNESS (ADVANCE FUNCTIONS)
10-WAY WIRING HARNESS (CAR START FUNCTIONS)
STATUS INDICATOR ASSEMBLY
DIPOLE ANTENNA
HOOD SAFETY SWITCH ASSEMBLY
125 DB SIREN ASSEMBLY
INSTALLATION PARTS BAG
FUSE PARTS BAG
OPERATORS INSTRUCTION
OPERATORS QUICK REFERENCE WALLET CARD
VSS WINDOW WARNING DECAL
UNDERHOOD WARNING LABEL
QTY
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
2W7Z-19G364-BA
Remote Start System w/Keyless Entry Kit (RKE/RMST)
REF
A
B
C
I
J
K
L
G
M
S - BB
CC, DD
R
S
P
6/42
DESCRIPTION
PC-32 MODULE ASSEMBLY
RKE/RMST DNA ASSEMBLY (2W7J-19G367-DA)
4 BUTTON POWERCODE TRANSMITTER W/REMOTE START ICONS
24-WAY WIRING HARNESS (BASE)
16-WAY WIRING HARNESS (ADVANCE FUNCTIONS)
10-WAY WIRING HARNESS (CAR START FUNCTIONS)
STATUS INDICATOR ASSEMBLY
DIPOLE ANTENNA
HOOD SAFETY SWITCH ASSEMBLY
INSTALLATION PARTS BAG
FUSE PARTS BAG
OPERATORS INSTRUCTION
OPERATORS QUICK REFERENCE WALLET CARD
UNDERHOOD WARNING LABEL
2W7Z-16A901-AA
SK5W7J-19A361-AA
QTY
1
1
2
1
1
1
1
1
1
1
1
1
1
1
© Copyright Ford 2005
Rev Date- 8/29/05
2W7Z-19G364-CA
Remote Start System Kit (RMST)
REF
A
B
F
I
K
L
G
M
S - BB
CC, DD
R
S
P
DESCRIPTION
PC-32 MODULE ASSEMBLY
RMST DNA ASSEMBLY (2W7J-19G367-CA)
2 BUTTON POWERCODE TRANSMITTER W/REMOTE START ICON
24-WAY WIRING HARNESS (BASE)
10-WAY WIRING HARNESS (CAR START FUNCTIONS)
STATUS INDICATOR ASSEMBLY
DIPOLE ANTENNA
HOOD SAFETY SWITCH ASSEMBLY
INSTALLATION PARTS BAG
FUSE PARTS BAG
OPERATORS INSTRUCTION
OPERATORS QUICK REFERENCE WALLET CARD
UNDERHOOD WARNING LABEL
QTY
1
1
2
1
1
1
1
1
1
1
1
1
1
2W7Z-19A361-DA
Deluxe Vehicle Security and Keyless Entry Kit (Deluxe RKE/VSS)
REF
A
B
D
I
J
L
G
N
S - BB
CC, DD
R
S
O
7/42
DESCRIPTION
PC-12 MODULE ASSEMBLY
Deluxe RKE/VSS DNA ASSEMBLY (2W7J-19A498-DA)
4 BUTTON POWERCODE TRANSMITTER W/HEADLIGHT ICONS
24-WAY WIRING HARNESS (BASE)
16-WAY WIRING HARNESS (ADVANCE FUNCTIONS)
STATUS INDICATOR ASSEMBLY
DIPOLE ANTENNA
125 DB SIREN ASSEMBLY
INSTALLATION PARTS BAG
FUSE PARTS BAG
OPERATORS INSTRUCTION
OPERATORS QUICK REFERENCE WALLET CARD
VSS WINDOW WARNING DECAL
2W7Z-16A901-AA
SK5W7J-19A361-AA
QTY
1
1
2
1
1
1
1
1
1
1
1
1
2
© Copyright Ford 2005
Rev Date- 8/29/05
2W7Z-19A361-CA
Vehicle Security and Keyless Entry Kit (RKE/VSS)
REF
A
B
C
I
L
H
S - BB
CC, DD
R
S
O
DESCRIPTION
PC-12 MODULE ASSEMBLY
RKE/VSS DNA ASSEMBLY (2W7J-19A498-CA)
2 BUTTON POWERCODE TRANSMITTER W/LOCK, UNLOCK ICONS
24-WAY WIRING HARNESS (BASE)
STATUS INDICATOR ASSEMBLY
WHIP ANTENNA
INSTALLATION PARTS BAG
FUSE PARTS BAG
OPERATORS INSTRUCTION
OPERATORS QUICK REFERENCE WALLET CARD
VSS WINDOW WARNING DECAL
QTY
1
1
2
1
1
1
1
1
1
1
2
2W7Z-19A361-BA
Vehicle Security Kit (VSS)
REF
A
B
I
L
H
S - BB
CC, DD
R
S
O
DESCRIPTION
PC-12 MODULE ASSEMBLY
VSS DNA ASSEMBLY (2W7J-19A498-CA)
24-WAY WIRING HARNESS (BASE)
STATUS INDICATOR ASSEMBLY
WHIP ANTENNA
INSTALLATION PARTS BAG
FUSE PARTS BAG
OPERATORS INSTRUCTION
OPERATORS QUICK REFERENCE WALLET CARD
VSS WINDOW WARNING DECAL
QTY
1
1
1
1
1
1
1
1
1
2
2W7Z-19A361-AA
Keyless Entry Kit (RKE)
REF
A
B
I
L
H
S - BB
CC, DD
R
S
8/42
DESCRIPTION
PC-12 MODULE ASSEMBLY
RKE DNA ASSEMBLY (2W7J-19A498-BA)
24-WAY WIRING HARNESS (BASE)
STATUS INDICATOR ASSEMBLY
WHIP ANTENNA
INSTALLATION PARTS BAG
FUSE PARTS BAG
OPERATORS INSTRUCTION
OPERATORS QUICK REFERENCE WALLET CARD
2W7Z-16A901-AA
SK5W7J-19A361-AA
QTY
1
1
1
1
1
1
1
1
1
© Copyright Ford 2005
Rev Date- 8/29/05
MODULE PREPARATION
PK LIGHTS
DOME LIGHT
DOOR LOCKS
5
15
15
15
2
+
15
15
15
-
15
5
15
15
15
+
DRIVER DOOR UNLOCK/
TRUNK RELEASE
15
Place the supplied fuses into the power distribution
block on the control module. Refer to the fuse
placement drawing for the specific vehicle that you are
working on. Fuse placement drawings are located in
vehicle specific wiring sections.
In this diagram, the parking light fuse is shown in the
positive polarity position and the Dome light fuse is
shown in the negative polarity position.
Note: The HVAC1, HVAC2 and IGNITION fuses are only
used on systems including remote car start (requires
PC-32 module).
15
1
HVAC 1
MAIN B+
HVAC 2
IGNITION
Place the software cartridge (DNA) onto the control
module as shown.
3
Plug the wiring harness(es) into the module.
Harness A: 24-way, used on all systems;
Harness B: 10-way, used on all systems with car start;
Harness C: 16-way, used on systems with convenience
features (i.e. Headlight control, memory seat control)
along with some preload system installations in vehicles
without factory equipped RKE.
If you are installing a system that uses the whip
antenna (RKE, RKE/VSS or Preload), plug the whip
antenna into the module at this time.
9/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
C
A
B
© Copyright Ford 2005
Rev Date- 8/29/05
MODULE PREPARATION (Cont’t)
4
Referring to the vehicle specific wiring section for the
system being installed, gather all individual wires that
will be routed to the same areas of the vehicle into
groups. Cover each wire group with tape for
approximately 18”. Depending upon the vehicle, there
will be 2 - 5 different wire groups.
Trim the unused wires approximately 6 - 8” from the
module. Do not cut the override/programming button off
of the harness, it is used for all installations.
Unused wires
Driver kick panel harness
Steering column harness
5
Tape the harness sections together, making sure to cover all of the unused wires.
3” - 4”
2” - 3”
10/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
VEHICLE PREPARATION
1
A.
B.
2
3
To allow access to the necessary vehicle circuits,
remove the interior panels as required.
Identify the control module mounting location and
appropriate vehicle circuit connection points. Plan
wire harness routings that will be free and clear of
all moving underdash components (i.e. accelerator
pedal, adjustable position brake pedal assembly
and parking brake mechanism.
All models except LS, T-Bird, Escort, Econoline and
Super-Duty Pick-ups, remove the steering column
shroud to allow access to the PATS transceiver antenna
ring around the ignition switch lock cylinder.
Test for Factory Perimeter Alarm (vehicles equipped with factory RKE only):
1. Roll down the driver’s door window and then close all doors, hood, trunk or hatch;
2. Lock the doors using the factory RKE transmitter;
3. Wait one minute, then reach in the driver door window and open the drivers door (do not unlock doors with the factory
RKE remote).
€ If the vehicle’s horn begins sounding when the door is opened, the vehicle is equipped with factory perimeter alarm.
Unlock the doors with the factory RKE remote to turn off the alarm. In this case, wire the systems factory perimeter
alarm disarm wire to the vehicle’s perimeter alarm disarm input (See the vehicle specific wiring section). Skip the test
for door trim switch disable below.
€ If the horn does not begin sounding when the door is opened, the vehicle is not equipped with factory installed
perimeter alarm. Follow the test procedure below for door trim switch disable.
Test for Door Trim Switch Disable option (vehicles equipped with factory RKE only):
1. Roll down the driver door window and close all doors, hood, trunk or hatch;
2. Lock the doors using the factory RKE transmitter;
3. Wait one minute, then reach in the driver door window and press the door trim unlock switch.
€ If the doors unlock, the door trim disable feature is not enabled and no further action is required.
€ If the doors do not unlock, connect the system’s factory alarm disarm output as shown in the vehicle specific wiring
section or disable the door trim switch disable feature using the NGS or WDS testers.
11/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
DIPOLE ANTENNA MOUNTING
1
!
•
•
•
•
A.
B.
The optimum operating range for this system is
dependant upon proper selection of the mounting
location for the Dipole antenna.
Never mount the antenna behind (or on) any metal
film or metal film window tint on the windshield.
Never mount the antenna so that one of the antenna
elements touches or crosses any vehicle wiring and/
or metal.
On vehicles with no metal film in the windshield
around the mirror and a non-electronic mirror, mount
the di-pole antenna between the headliner and
rearview mirror.
On vehicles equipped with an “Electronic” mirror or
vehicles with metal film in the windshield near the
mirror, mount the di-pole antenna approximately 3”
below the mirrors attachment point to the windshield
and/or any mirror electronics;
Clean the selected mounting location using a
alcohol based glass cleaning solution.
Mount the Di-pole antenna as shown. Remove the
protective backing from the adhesive. Use care not
to touch the adhesive backing. Firmly press on the
body of the antenna to ensure good glass to
adhesive bond.
NON-ELECTRONIC
MIRROR
Metal Film in windshield
ELECTRONIC MIRROR
2
Route the antenna cable to the control module mounting
location. Make sure that the antenna cable is routed free
and clear of all moving assemblies such as the
emergency brake and/or the adjustable brake pedal
assembly.
The antenna cable can generally be “tucked” behind the
headliner and “A-pillar” trim panel(s) without the need to
loosen or remove any of the trim panels. If it is
necessary to loosen or remove any of the interior trim
panels to run the antenna cable, proceed with caution as
these trim pieces are sometimes easily damaged. Also
note that some interior trim fasteners are “one-time” use
and must be replaced if removed.
12/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
STATUS LED
1
3
5
Identify a suitable mounting location for the status LED.
Make sure that there is at least 3/4” clearance behind
the selected mounting location.
4
Drill a 9/32” mounting hole.
If necessary, reinstall any interior trim panels removed
during this procedure.
13/42
2W7Z-16A901-AA
2
6
SK5W7J-19A361-AA
If necessary, remove the selected trim panel
Insert status LED into drilled hole.
The LED will plug into the main wiring harness during
the wiring steps. Make sure to leave the LED pigtail
accessible.
© Copyright Ford 2005
Rev Date- 8/29/05
SECURILOCK INTERFACE KITS - 1L2Z-19G365-AB & 1S4Z-19G365-AB
1
Route the loop end of Securilock interface antenna ( B )
up along steering column to the area around the PATS
transceiver antenna coil. Then using the supplied small
tie wraps, secure the antenna harness to existing vehicle
wiring harnesses along the steering column allowing
enough slack for the antenna loop to go around the
PATS transceiver antenna.
SECURILOCK KIT
COMPONENTS
A
D
NOTE: On LS and T-Bird, the ignition switch is mounted
on the dash to the right of the steering column. On those
vehicles, route the securilock interface antenna loop to
the ignition switch.
E
B
C
2
Following the directions on the supplied ampule of
adhesive primer ( D ), apply a thin coating primer to
entire transceiver antenna coil. Allow the primer to dry
for 5 minutes before proceeding with the next step.
D
3
Remove backing from one side of supplied two-way tape
( E ) and apply tape around transceiver antenna coil.
E
14/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
SECURILOCK INTERFACE KITS - 1L2Z-19G365-AB & 1S4Z-19G365-AB (Con’t)
4
B
Carefully unwrap four (4) inches of the twisted red wire
away from the Securilock PATS antenna loop ( B ).
5
Remove backing on tape ( E ) and position antenna
loop ( B ) on tape around antenna coil.
Make sure to align stripe (Black or Red) on antenna loop
directly over the PATS antenna coil. The antenna is
located near the outer edge (key side) of the transceiver
housing. Press on antenna loop wire to ensure initial
bond between tape and wire.
B
Stripe
6
A.
Use a tie wrap ( Y ) to complete the bottom of the
antenna loop as shown. Make sure that the
Securilock PATS antenna loop ( B ) is as close to
the PATS antenna as possible.
CORRECT
INCORRECT
Y
15/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
SECURILOCK INTERFACE KITS - 1L2Z-19G365-AB & 1S4Z-19G365-AB (Con’t)
7
A. Using the unwrapped red lead wire make an
additional wrap around the Securilock PATS antenna
loop as close as possible to the stripe (red or Black)
on the Securilock PATS antenna loop.
Y
B. Use a tie strap ( Y ) to secure the additional wrap
around the PATS antenna.
8
A.
B.
Mount the Securilock Interface Module ( A ) to an
underdash wiring harness using one of the supplied
long tie wraps (X) as shown. DO NOT mount the
Securilock Interface Module: 1) To or within 3” of a
metal surface, including any underdash brackets, or
2) In the knee bolster area.
Route the harness and connector ( C ) to module
mounting location.
Vehicle wiring harness
X
A
16/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
SECURILOCK INTERFACE KIT - 1L3Z-19G365-AB
1
Route the loop end of PATS interface antenna ( B ) lead
up along steering column to area around transceiver
antenna coil.
SECURILOCK KIT
COMPONENTS
A
B
C
2
Slip antenna loop ( B ) over PATS transceiver.
B
3
A.
B.
Mount the Securilock Interface Module ( A ) to an
underdash wiring harness using one of the supplied
long tie wraps (X) as shown. DO NOT mount the
Securilock Interface Module: 1) To or within 3” of a
metal surface, including any underdash brackets, or
2) In the knee bolster area.
Route the harness and connector ( C ) to module
mounting location.
Vehicle wiring harness
A
17/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
X
© Copyright Ford 2005
Rev Date- 8/29/05
SIREN INSTALLATION
1
Locate a suitable mounting location that away from hot
and/or moving vehicle/engine components.
2
BB
BB
Mount siren using screws provided (BB). Apply
rustproofing compound (Super Seal #F3AZ-19515-SA)
to drilled holes and mounting screws.
Locate a vehicle grommet to route wire through
bulkhead panel.
4
A
S
RU ILICO
BB NE
ER
3
B
C
Pass wires into vehicles interior compartment. Use
silicone sealer (P/N D6AZ-19562-AA) as necessary to
seal grommet.
18/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
HOOD TILT SWITCH INSTALLATION
1
2
Locate an easy to access area near the drivers side
hood hinge.
Mount the hood safety switch using the supplied sheet
metal screws (BB) so that the switch will be biased
downward when the hood is closed. Route the wire
carefully avoiding any moving parts or excessive heat.
2x
BB
3
Select a proper grounding point and clean surface of
paint, grease and dirt. Attach ground lug to connection
point using the sheet metal screw provided (BB). Torque
ground screw to 10 in / lbs. Apply rustproofing compound
(Super Seal #F3AZ-19515-SA) to drilled hole.
Note: Ground connection must be tight and secure.
Failure of ground connection can prevent proper
operation of system.
The remaining hood switch wire will be connected during
the wiring steps. Refer to the siren installation steps for
directions on routing this wiring through the bulkhead
panel.
10 in / lbs
BB
M
19/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
MOUNTING THE CONTROL MODULE
1
Plug the connectors for the Securilock interface and
antenna (if not already done) into the control module as
shown.
Trim and tape off
To Securilock
module
WHITE
2
Plug the Status LED into the main wiring harness.
To Status LED
Main wire
harness
3
A.
B.
!
20/42
RF Antenna
Using the supplied long tie wraps (X), mount the
control module to underdash wiring harnesses and/
or dash mounting brackets. Module mounting
locations are provided on the last page of the
vehicle specific wiring sections. DO NOT mount the
control module in the knee bolster area. To ensure
best performance of the built-in shock sensor,
securely tie wrap the control module at three points
to the vehicle.
Route the different sections of the wiring harness to
the appropriate underdash areas of the vehicle.
Neatness in this area is very important in ensuring a
quality finished installation. Wherever possible, route
the PowerCode system wires along with existing
vehicle wiring harnesses and tie wrap the
PowerCode wiring harnesses to existing vehicle
wiring harnesses.
Make sure to route the PowerCode system wiring so
that it is free and clear of all moving underdash
components (i.e. accelerator pedal, adjustable brake
pedal assembly and/or parking brake mechanism).
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
SYSTEM WIRING CONNECTIONS
1
A.
B.
Finish routing the systems wiring harnesses to their destination points and secure all system wiring using the supplied tie
wraps (Y).
Make the wiring connections as shown. Vehicle specific wiring diagrams begin on page 42.
Make sure to test each vehicle circuit prior to making any connections - All vehicle wiring is subject to
change.
Instructions on proper wiring connection methods and circuit testing can be found in the reference section of this
manual.
C.
After completing all the system wiring, follow the instructions beginning on the next page to program and test the systems
functionality.
NOTE: The system will not function properly if not programmed.
WARNING LABEL INSTALLATION
1
2
WARNING: / AVERTISSEMENT
This vehicle is equipped with a remote controlled engine starter.
To reduce the risk of serious Injury or death, switch engine starter
system into service mode and disconnect the vehicle battery
before performing any service on the vehicle.
Ce véhicule est doté d'un démarreur à distance. Pour réduire les
risques de blessures graves ou mortelles, mettre le démarreur à
distance en mode service et débrancher la batterie du véhicule
avant d'effectuer des travaux d'entretien sur celui-ci.
RMST SYSTEMS ONLY - Install the Orange
warning label on the radiator shroud (or similar
area).
21/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
VSS SYSTEMS ONLY - Install the window decals on
both the driver and passenger side windows.
© Copyright Ford 2005
Rev Date- 8/29/05
System Programming Instructions
1
Transmitter programming:
A.
Open the driver’s door (press and hold in brake pedal on Remote Start only system);
!
NOTE: On vehicles with negative polarity door ajar switch input circuits (Refer to the vehicle specific
programming section), the door is closed during this step unless the door ajar switch input polarity option
has been previously changed to negative.
B. Turn the ignition key to the ON or RUN position;
C. Press and hold the programming/override button;
After 10 seconds the horn will chirp 3 times, indicating the system is now in the transmitter learn mode.
D. Release the programming/override button;
on all, except RMST system which is
) on the on the remote control transmitter to
E. Press transmitter button 1(
be programmed.
The horn will chirp one time to indicate that the transmitter has been learned.
Notes:
A. Up to a total of 8 transmitters can be programmed at this time
B. Transmitters shipped with complete kits or personality kits are pre-programmed to the DNA and do not need to be
programmed at this time.
C. If the vehicle is equipped with memory seats/functions, the last two transmitters programmed will activate the memory
seats/functions.
D. All programmed transmitters can be erased from memory by pressing the door trim switch “unlock button” while in
transmitter learn mode (requires that the Disarm input and Unlock sense input wires be connected)
2
Each system has several user programmable options which can be changed to accommodate different vehicle options and/
or consumers desires. Virtually every installation will require that some option(s) to be changed. Charts listing the options
for each system and the factory default settings are located on the following pages.
Option programming:
A. Follow the instructions above to enter transmitter learn mode;
B. Press and release the programming/override button.
The horn will chirp four times indicating the system has entered the first option bank.
Note:
Depending upon the system that you are working with, there will be anywhere from 2 – 5 option programming banks. Each
option bank contains anywhere from 2 – 8 options.
To change the setting of an option (Remote control systems):
A. Press button 3 (see chart to the right) to advance to the desired option (refer to
the programming charts on the following pages for the specific system that you
are programming;
The horn will chirp a number of times to indicate which option is selected (i.e. Two
chirps indicates that option number two has been selected).
B. Press the button 1 to change the setting of the option
The status LED indicates the setting of the option: LED ON indicates that the
option is on, LED OFF indicates that the option is off.
Note:
Pressing transmitter button 2 while in any option bank will reset all options, except for
the “Installer” options and the shock sensor to their factory settings. The system will
respond by chirping the horn 4 times.
22/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
Press both
buttons together
3
1
2
3
4 Button
Transmitter
1
2
2 Button
Transmiter
© Copyright Ford 2005
Rev Date- 8/29/05
System Programming Instructions (Con’t)
2
CONTINUED
To change the setting of an option (VSS system):
A.
Press the door trim “Lock” switch to advance to the desired option (refer to the programming charts on the following
pages for the specific system that you are programming;
The horn will chirp a number of times to indicate which option is selected (i.e. Two chirps indicates that option number two
has been selected).
B.
Press the door trim “Unlock” switch to change the setting of the option
The status LED indicates the setting of the option: LED ON indicates that the option is on, LED OFF indicates that the
option is off.
Note:
Pressing the door trim switch “lock button” while in transmitter learn mode will reset all options to their factory default settings,
except for the installer options and shock sensor settings. The system will respond by chirping the horn 4 times.
To advance to the next option bank:
A. At any point while in option programming, press and release the programming/override button to advance to the next
option bank.
The horn will chirp a number of times, indicating which option bank the system has entered (i.e. 5 chirps indicates that
the system is in option programming bank #2. Refer to the option programming chart to correlate the horn chirps to option
bank).
3
Shock sensor setting (not applicable to RKE or RKE/RMST systems)
The “Lite-touch” and “Full shock” sensor settings are always the first and second options, respectively, in the
first option bank. To change a shock sensor setting, follow these steps:
Remote control systems:
A. Enter option learn mode, option bank 1, as shown in step 2 of this section.
B. Go to option #1 for Lite-touch or option #2 for Full shock.
C. After the desired option is selected, pressing transmitter button 1 will increase sensitivity and pressing transmitter
button 2 will decrease sensitivity.
The system will chirp the horn each time a impact is detected that is greater than the current setting while the system is
in shock sensor setting mode.
VSS System
A. Make sure that the drivers window is rolled down.
B. Enter option learn mode, option bank 1, as shown in step 2 of this section.
C. Go to option #1 for Lite-touch or option #2 for Full shock.
D. Select the desired option and close all doors.
E. Press the door trim “Unlock” switch to increase sensitivity and pressing the door trim “Lock” switch to decrease sensitivity.
The system will chirp the horn each time a impact is detected that is greater than the current setting while the system is
in shock sensor setting mode.
F. Once the desired sensitivity is achieved, open a door to advance to the next option.
All Security Sytems:
A. The Full trigger shock sensor setting must be set within 10 increments of the least sensative setting and the “lite-touch”
setting must be set to within 30 increments of the least sensative setting.
B. Deviation from this setting recomendation introduces the potential of false alarm triggers, due to electrical or mechanical
interference.
23/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
System Programming Instructions - Remote Start Systems
4
Tach (Idle speed) programming - Remote Start Systems Only
A.
Make sure that the hood is closed before proceeding.
B.
Enter option learn mode as described in step 2 of this section.
C.
€ RKE/VSS/RMST & RKE/RMST systems - Advance to option bank # 5 (8 chirps)
€ RMST system - Advance to option bank #2 (5 chirps) .
D.
€ RKE/VSS/RMST & RKE/RMST system - Advance to option #6;
€ RMST system - Advance to option #2.
E.
Press and hold in the brake pedal and start the engine using the ignition key.
Allow the engine to settle to a normal idle speed. The system will chirp the horn every three (3) seconds if a valid tach signal is
detected.
F.
After the engine has settled to a normal idle speed, press and release the programming/override button (the horn will honk four (4)
times) and turn the ignition key off.
NOTE:
5
If the system is not chirping the horn every three (3) seconds after the engine has started, the system is not seeing a valid tach
signal. Check your tach connection (refer to the appropriate vehicle specific wiring diagram)
Securilock (PATS) Interface Programming and Remote Start Operation Test
(two programmed PATS ignition keys are required for this step)
NOTE: This step does not apply to Econoline, SuperDuty Pick-ups and Escort
A.
Sitting in the driver seat, be prepared to press the brake pedal to shut down the remote starter system.
B.
Using the first key, turn the ignition on, wait for the THEFT light to turn off, then turn the ignition off and remove key from the ignition
switch.
C.
Using the second key, turn the ignition on, wait for the THEFT light to turn off, then turn the ignition off and remove key from the ignition
switch.
D.
Activate the remote start function using the PowerCode remote control transmitter.
E.
After the engine is started. Press the brake pedal to shutdown the engine.
The Securilock interface is now programmed. If the theft light begins flashing rapidly and/or the engine does not crank or cranks but
will not start, refer to the troubleshooting information below.
The system should flash the parking lights and chirp the horn one time, pause for four seconds then start then start the engine.
F.
Open the hood.
G.
Sitting in driver’s seat, be prepared to press the brake pedal, activate the start function.
H.
Close the hood.
The system should chirp the horn two (2) times and abort the start sequence.
I.
Place ignition key in the ignition cylinder.
J.
Again, Sitting in driver’s seat, be prepared to press the brake pedal and activate a start sequence.
The system should chirp the horn one (1) time pause four seconds, then chirp the horn two (2) times and abort the start sequence.
!
A.
In steps G and J above, the engine MUST NOT start! If the system starts the engine in either steps G or J, check your hood tilt switch
installation and key-in-sense connection.
Troubleshooting steps:
If the Securilock interface fails to program (theft light flashing), check the following:
When programming the Securilock Interface timing is important, make sure that you:
1.
Turn the ignition on with the second key within 5 seconds of the theft light going out on the first key;
2.
Engage the remote start within 5 seconds of the theft going out on the second key;
3.
Remove the second ignition key before engaging the remote starter.
NOTE: If a third (or more) PATS ignition key has been programmed to the vehicle using either the Ford NGS or WDS programmers, the “Add
Key” mode described in the installation manual may have been disabled. If this is the case, use the NGS or WDS programmer to either reenable the “add key” mode or program the Securilock Interface kit following the NGS or WDS procedure in the vehicle service manual for
adding a new PATS key.
B.
If the theft light is solid and engine cranks but will not start:
Check all Ignition (Hot through run and crank circuits) and Heater (Run circuits). Make sure that the correct outputs from the
PowerCode module are connected to the correct vehicle circuits. Reversing the heater and ignition circuits from the PowerCode
system will not permanently damage the vehicle but may cause the remote start function to not work and/or set a PCM error codes
(which will cause the check engine light to stay on). If the check engine light stays on, use the NGS or WDS testers to identify which
fault code has been set. The fault code will help identify which circuit is not properly connected.
24/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
System Programming Instructions - Security/Convenience Function Test
1
Refer to the Operators manual as necessary and check out the following functions. If any of the functions below, fail to
operate, first refer to the vehicle specific wiring diagrams and check the wiring and system programming.
Convenience Functions
All Door Lock / All Door Unlock
Driver door unlock (if installed)
Parking light flash
Trunk or hatch release
Illuminated entry
Ignition triggered lock/unlock (if enabled)
Illuminated exit
Panic alarm
Memory Seat activation (if equipped)
Power Side Sliding door activation (if equipped - Windstar only)
Power Tonneau cover activation (Blackwood only)
Express window down (LS only)
Headlight illumination (if installed)
Security Functions
Security System Arm / Disarm
Using PowerCode remote control transmitters
Using Factory RKE Keyfobs
Verify interior door trim unlock switch DOES NOT disarm system
All entry points trip alarm cycle
Status indicator flashes when armed
Siren (if installed)
Shock sensor settings (lite-touch & full shock)
Remote start convenience functions
Heater & A/C operation during remote start
Rear defroster (if installed)
Remote start safety functions
No remote start activation with the ignition key inserted into the ignition switch
No remote start activation with the vehicle’s hood open
No remote start activation with the vehicle’s brake pedal depressed
25/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
SECURILOCK INTERFACE AND RELAY APPLICATION CHART
Note: Application information is also located in the
vehicle specific wiring section
Relay Requirements
Securilock
Rear Driver Door
Headlight Defroster Unlock
Interface Kit
2002
Crown Victoria/Grand Marquis 1L3Z-19G365-AB
1
Econoline
Not Equipped
1
1
Escort
Not Equipped
1
Escape
1S4Z-19G365-AB
1
1
1
F-150 (Includes Supercrew) 1L3Z-19G365-AB
1
1
F-250/350 (Super-Duty)
Not Equipped
1
1
Expedition/Navaigator
1L3Z-19G365-AB
1
1
Excursion
1L3Z-19G365-AB
1
1
LS-6/8
1S4Z-19G365-AB
1
Focus
1
1S4Z-19G365-AB
Mustang
1
1
1L3Z-19G365-AB
1
Ranger
1
1
1L2Z-19G365-AB
1
Explorer/Mountaineer
1L2Z-19G365-AB
1
1
Explorer Sport/Sport Trac
1L2Z-19G365-AB
1
1
Town Car
1L3Z-19G365-AB
1
Taurus/Sable
1L2Z-19G365-AB
1
1
Windstar
1L2Z-19G365-AB
1
T-Bird
1
1S4Z-19G365-AB
2003
1
1
Aviator
1L2Z-19G365-AB
1
Crown Victoria/Grand Marquis 1L2Z-19G365-AB
Econoline
Not Equipped
1
1
Escort
Not Equipped
1
Escape
1S4Z-19G365-AB
1
F-150 (Includes Supercrew) 1L3Z-19G365-AB
1
1
F-250/350 (Super-Duty)
Not Equipped
1
1
1
Expedition/Navaigator
1L2Z-19G365-AB
1
Excursion
1L3Z-19G365-AB
1
1
1
LS-6/8
1
1L2Z-19G365-AB
Focus
1S4Z-19G365-AB
1
1
Mustang
1L3Z-19G365-AB
1
1
1
Ranger
1
1
1L2Z-19G365-AB
Explorer/Mountaineer
1L2Z-19G365-AB
1
1
Explorer Sport/Sport Trac
1L2Z-19G365-AB
1
1
1
Town Car
1L2Z-19G365-AB
1
Taurus/Sable
1L2Z-19G365-AB
1
1
Windstar
1L2Z-19G365-AB
1
T-Bird
1
1L2Z-19G365-AB
Model Year / Model
26/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
Other
E, F
E
A, E
B
A
Relay’s are available by
ordering part numbers:
Single: YL3Z-19G390-AA
10 Pack:YL3Z-19G390-BA
A
B
B, F
D
E,F
E
A, E
A
C
A
A - Trim switchdisable,
requires 1 relay
B - Memory seats,
requires 2 relays
C - Parking lights,
requires 1 relay
D - Key latch
release - 1 relay
E- Door Lock/Unlock,
requires 2 relays for
vehicles w/o factory RKE
F- Remote Start Systems
requires 2 relays
B
B, F
© Copyright Ford 2005
Rev Date- 8/29/05
SECURILOCK INTERFACE AND RELAY APPLICATION CHART
Note: Application information is also located in the
vehicle specific wiring section
Relay Requirements
Securilock
Rear Driver Door
Other
Headlight Defroster Unlock
Interface Kit
2004
Aviator
1L2Z-19G365-AB
1
D
Crown Victoria/Grand Marquis 1L2Z-19G365-AB
E, F
Econoline
Not Equipped
1
1
E, G
Escape
1S4Z-19G365-AB
1
1
E
F-150 (Classic Body)
1L3Z-19G365-AB
1
1
F-150 (New Body)
1L2Z-19G365-AB
1
F-250/350 (Super Duty)
Not Equipped
1
1
A, E, G
1
Expedition/Navaigator
1L2Z-19G365-AB
1
1
Excursion
1L3Z-19G365-AB
1
A, G
LS-6/8
1L2Z-19G365-AB
H
Focus
1
1S4Z-19G365-AB
Freestar/Monterey
1L2Z-19G365-AB
1
1
C
Mustang
1
1
1L3Z-19G365-AB
1
Ranger
1
1
1L2Z-19G365-AB
1
Explorer/Mountaineer
1L2Z-19G365-AB
1
1
Explorer Sport/Sport Trac
1L2Z-19G365-AB
1
1
Town Car
1L2Z-19G365-AB
1
B, F
Taurus/Sable
1L2Z-19G365-AB
1
1
T-Bird
1
1L2Z-19G365-AB
2005
1
1
Aviator
1L2Z-19G365-AB
D
Crown Victoria/Grand Marquis 1L2Z-19G365-AB
1
E
Econoline
Not Equipped
1
1
E, G
Escape
1L2Z-19G365-AB
1
1
F-250/350 (Super Duty)
A, E, G
1
Not Equipped
F-150 (New Body)
1L2Z-19G365-AB
1
1
1
Expedition/Navigator
1L2Z-19G365-AB
1
Excursion
1L3Z-19G365-AB
1
A, G
1
1
Five Hundred/Freestyle
1L2Z-19G365-AB
Focus
1S4Z-19G365-AB
1
Freestar/Monterey
1L2Z-19G365-AB
1
1
1
C
LS-6/8
1L2Z-19G365-AB
H
1
C
Mustang (New)
1L2Z-19G365-AB
Explorer/Mountaineer
1L2Z-19G365-AB
1
1
Explorer Sport/Sport Trac
1L2Z-19G365-AB
1
1
1
1
Ranger
Not Equipped
T-Bird
1L2Z-19G365-AB
1
Town Car
1L2Z-19G365-AB
B
1
Taurus/Sable
1L2Z-19G365-AB
1
1
Model Year / Model
27/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
Relay's are available by
ordering part numbers:
Single: YL3Z-19G390-AA
10 Pack:YL3Z-19G390-BA
A - Trim switchdisable,
requires 1 relay
B - Memory seats,
requires 2 relays
C - Parking lights,
requires 1 relay
D - Key latch
release - 1 relay
E- Door Lock/Unlock,
requires 2 relays for
vehicles w/o factory RKE
F- Remote Start Systems
requires 2 relays
G- Tach Inverter required
for vehicles with 6.0Liter
diesel engines
H- Parking lights,
requires 2 relays
© Copyright Ford 2005
Rev Date- 8/29/05
SECURILOCK INTERFACE AND RELAY APPLICATION CHART
Note: Application information is also located in the
vehicle specific wiring section
Model Year / Model
2006
Crown Victoria/Grand Marquis
Econoline
Escape
F-250/F-350 (Super Duty)
F-150
Expedition
Explorer
Five Hundred
Focus
Freestar
Freestyle
Fusion
Grand Marquis
LS-6/8
Milan
Marauder
Montego
Monterey
Mustang
Navigator
Ranger
Taurus
Town Car
Zephyr
28/42
2W7Z-16A901-AA
Securilock
Interface Kit
1L2Z-19G365-AB
Not Equipped
1S4Z-19G365-AB
Not Equipped
1L2Z-19G365-AB
1L2Z-19G365-AB
1L2Z-19G365-AB
1L2Z-19G365-AB
1L2Z-19G365-AB
1L2Z-19G365-AB
1L2Z-19G365-AB
1L2Z-19G365-AB
1L2Z-19G365-AB
1L2Z-19G365-AB
1L2Z-19G365-AB
1L2Z-19G365-AB
1L2Z-19G365-AB
1L2Z-19G365-AB
1L2Z-19G365-AB
1L2Z-19G365-AB
1L2Z-19G365-AB
1L2Z-19G365-AB
1L2Z-19G365-AB
1L2Z-19G365-AB
Relay Requirements
Rear
Driver Door
Headlight Defroster Unlock
1
1
1
1
1
1
1
Other
D
D, E
A, D, E
1
1
1
1
1
1
1
1
1
1
1
SK5W7J-19A361-AA
Relay's are available by
ordering part numbers:
Single: YL3Z-19G390-AA
10 Pack:YL3Z-19G390-BA
1
1
1
1
1
1
1
1
1
C
F
D
F
F
D
C
C
A - Trim switchdisable,
requires 1 relay
B - Memory seats,
requires 2 relays
C - Parking lights,
requires 1 relay
D- Door Lock/Unlock,
requires 2 relays for
vehicles w/o factory RKE
E- Tach Inverter required
for vehicles with 6.0Liter
diesel engines
F- Parking lights,
requires 2 relays
B
F
© Copyright Ford 2005
Rev Date- 8/29/05
RKE/VSS/RMST OPTION CHART
Option Bank 1 – 4 chirps
Factory setting
1 – Lite-touch adjustment
2 – Full shock adjustment
3 – Optional alarm disable
Disables security functionality. .................................................................................................................... Off
4 – Passive starter Interrupt
Starter interrupt activates 1 minutes after key off event. ............................................................................ Off
5 – Passive arming
Security system activates 1 minutes after key off event. ............................................................................ Off
6 – Passive door locks
All doors lock automatically 1 minutes after key off event. ......................................................................... Off
7 – Selectable chirps
Enables arming/disarming confirmation chirps (uses horn). ...................................................................... On
8 – Silent choice
On – Confirmation chirp on second press of transmitter button
Off – Confirmation chirp on first press of transmitter button.
Requires option #7 (above) to be ON. ........................................................................................................ On
Option Bank 2 – 5 chirps
Factory setting
1 – Drivers door priority unlock
Drivers door only unlocks on first press of Disarm/Unlock,
All doors unlock on second press within 5 seconds. .................................................................................. Off
2 – Ignition lock
All doors lock when ignition key is turned to on (run). ................................................................................ Off
3 – Ignition unlock
All doors are unlocked when ignition key is turned to off. .......................................................................... Off
4 – Delayed door lock for ignition lock
Waits 3 seconds after key on event before activating ignition lock.
Used on vehicles with theater dimming interior lights. ............................................................................... Off
5 – Illuminated exit
Activates dome light output for one minute when ignition key is turned off ................................................ On
6 – Horn used for alarm
Horn sounds during alarm/panic cycles ..................................................................................................... On
7 – Noise control
Limits alarm trips to 5 per zone .................................................................................................................. On
8 – Factory RKE system does not arm alarm
Prevents factory RKE from arming security system. Still allows
factory RKE to disarm security system. ...................................................................................................... Off
Option Bank 3 – 6 chirps
Factory setting
1 – Tach diagnostic mode
This feature should only be used for troubleshooting purposes only!
Car start function ignores tach input and cranks starter one time for one second.
WARNING – Over rev and stall detection is disabled when this option is enabled. ................................... Off
2 – Car start run time
LED On – 15 minutes, LED Off – 10 minutes ............................................................................................ Off
3 – Lock after start
(Re)locks doors after remote start. ............................................................................................................. Off
4 – One button start
Activates remote start by press and hold of start button. ........................................................................... Off
5 – Diesel timer
Delays crank attempt 30 seconds after ignition on. .................................................................................... Off
6 – Rear Defrost output activation
LED On- Activation only after remote start, LED Off- Activation anytime .................................................... On
29/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
RKE/VSS/RMST OPTION CHART (Cont’t)
Option Bank 4 – 7 chirps
1 – Headlight Output Time (used only when option #5 below is in the LED Off position)*
LED On – 20 seconds, LED Off – .5 seconds ........................................................................................... On (20 sec.)
2 – Rear Defrost Output Time
LED On – 10 minutes, LED Off – .5 seconds ............................................................................................ Off (.5 sec.)
3 – Auxilliary Output Time
LED On – .5 seconds, LED Off – Time held .............................................................................................. On (.5 sec.)
4 – Power Sliding Door Output Time (used only when option #5 below is in the LED On position)*
LED On – .5 seconds, LED Off – Time held .............................................................................................. On (.5 sec.)
5 – Convert headlight output to act as the power sliding door output ..............................................................
(controlled by pressing Find/Panic and Start buttons simultaneously)
LED On- Power Sliding Door Output, LED Off- Headlight Output ............................................................. Off
* The Headlight Output and Power Sliding Door Output both use the C-10 Red/White wire
Option Bank 5 – 8 chirps
1 – Door ajar switch input polarity
LED On – Positive, LED Off – Negative ..................................................................................................... On (Positive)
2 – Unlock switch sense input polarity
LED On – Positive, LED Off – Negative ..................................................................................................... On (Positive)
3 – Key-in sense input polarity
LED On – Positive, LED Off – Negative ..................................................................................................... Off (Negative)
4 – Door Ajar Input Entry Delay
5 Second entry delay. Used for vehicles with external door mounted RKE keypads ................................. Off
5 – Use trunk relay as Driver door unlock
Switches Trunk release and Drivers door unlock outputs ........................................................................... Off
6 – Learn tachometer
With hood open or brake pedal pressed start engine. System will chirp horn
every five seconds if a valid tach signal is present.
30/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
RKE/RMST OPTION CHART
Option Bank 1 – 4 chirps
Factory setting
1 – Passive starter Interrupt
Starter interrupt activates 1 minutes after key off event. ............................................................................ Off
2 – Passive door locks
All doors lock automatically 1 minutes after key off event. ......................................................................... Off
3 – Selectable chirps
Enables arming/disarming confirmation chirps (uses horn). ...................................................................... On
4 – Silent choice
On – Confirmation chirp on second press of transmitter button
Off – Confirmation chirp on first press of transmitter button.
Requires option #7 (above) to be ON. ........................................................................................................ On
Option Bank 2 – 5 chirps
Factory setting
1 – Drivers door priority unlock
Drivers door only unlocks on first press of Disarm/Unlock,
All doors unlock on second press within 5 seconds. .................................................................................. Off
2 – Ignition lock
All doors lock when ignition key is turned to on (run). ................................................................................ Off
3 – Ignition unlock
All doors are unlocked when ignition key is turned to off. .......................................................................... Off
4 – Delayed door lock for ignition lock
Waits 3 seconds after key on event before activating ignition locked.
Used on vehicles with theater dimming interior lights. ............................................................................... Off
5 – Illuminated exit
Activates dome light output for one minute when ignition key is turned off ................................................ On
6 – Horn used for alarm
Horn sounds during alarm/panic cycles ..................................................................................................... On
7 – Factory RKE system does not arm alarm
Prevents factory RKE from arming security system. Still allows
factory RKE to disarm security system. ...................................................................................................... Off
Option Bank 3 – 6 chirps
Factory setting
1 – Tach diagnostic mode
This feature should only be used for troubleshooting purposes only!
Car start function ignores tach input, cranks starter one time for one second.
WARNING – Over rev and stall detection is disabled. ................................................................................ Off
2 – Car start run time
LED On – 15 minutes, LED Off – 10 minutes ............................................................................................ Off
3 – Lock after start
(Re)locks doors after remote start. ............................................................................................................. Off
4 – One button start
Activates remote start by press and hold of start button. ........................................................................... Off
5 – Diesel timer
Delays crank attempt 30 seconds after ignition on. .................................................................................... Off
6 – Rear defrost output activation
LED On-Activation after remote start, LED Off-Activation anytime ............................................................. On
31/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
RKE/RMST OPTION CHART (Cont’t)
Option Bank 4 – 7 chirps
1 –Headlight Output Time (used only when option #5 below is in the LED Off position)*
LED On – 20 seconds, LED Off – .5 seconds ........................................................................................... On (20 sec.)
2 –Rear Defrost Output Time
LED On – 10 minutes, LED Off – .5 seconds ............................................................................................ Off (.5 sec.)
3 – Auxillary Output Time
LED On – .5 seconds, LED Off – Time held .............................................................................................. On (.5 sec.)
4 –Power Sliding Door Output Time (used only when option #5 below is in the LED On position)*
LED On – .5 seconds, LED Off – Time held .............................................................................................. On (.5 sec.)
5 –Converts headlight to act as power sliding doors .......................................................................................
(controlled by pressing Find/Panic and Start buttons simultaneously)
LED On- Power Sliding Door Output ......................................................................................................... Off
* The Headlight Output and Power Sliding Door Output use the C-10 Red/White wire.
Option Bank 5 – 8 chirps
1 – Door switch input polarity
LED On – Positive, LED Off – Negative ..................................................................................................... On (Positive)
2 – Unlock switch sense input polarity
LED On – Positive, LED Off – Negative ..................................................................................................... On (Positive)
3 – Key-in sense input polarity
LED On – Positive, LED Off – Negative ..................................................................................................... Off (Negative)
4 – Use trunk relay as Driver door unlock
Switches Trunk release and Drivers door unlock outputs ........................................................................... Off
5 – Learn tachometer
With hood open or brake pedal pressed start engine. System will chirp horn
every five seconds if a valid tach signal is present.
32/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
RMST OPTION CHART
Option Bank 1 – 4 chirps
Factory setting
1 – Selectable chirps
Enables arming/disarming confirmation chirps (uses horn). ...................................................................... On
2 – Horn used for alarm
Horn sounds during alarm/panic cycles ..................................................................................................... On
3 – Tach diagnostic mode
This feature should only be used for troubleshooting purposes only!
Car start function ignores tach input, cranks starter one time for one second.
WARNING – Over rev and stall detection is disabled. ................................................................................ Off
4 – Car start run time
LED On – 15 minutes, LED Off – 10 minutes ............................................................................................ Off
5 – One button start
Activates remote start by press and hold of start button. ........................................................................... Off
6 – Diesel timer
Delays crank attempt 30 seconds after ignition on. .................................................................................... Off
Option Bank 2 – 5 chirps
Factory setting
1 – Key-in sense input polarity
LED On – Positive, LED Off – Negative ..................................................................................................... Off (Negative)
2 – Learn tachometer
With hood open start engine. System will chirp horn
every five seconds if a valid tach signal is present.
33/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
Deluxe RKE/VSS OPTION CHART
Option Bank 1 – 4 chirps
Factory setting
1 – Lite-touch adjustment
2 – Full shock adjustment
3 – Optional alarm disable
Disables security functionality. .................................................................................................................... Off
4 – Passive starter Interrupt
Starter interrupt activates 1 minutes after key off event. ............................................................................ Off
5 – Passive arming
Security system activates 1 minutes after key off event. ............................................................................ Off
6 – Passive door locks
All doors lock automatically 1 minutes after key off event. ......................................................................... Off
7 – Selectable chirps
Enables arming/disarming confirmation chirps (uses horn). ...................................................................... On
8 – Silent choice
On – Confirmation chirp on second press of transmitter button
Off – Confirmation chirp on first press of transmitter button.
Requires option #7 (above) to be ON. ........................................................................................................ On
Option Bank 2 – 5 chirps
Factory setting
1 – Drivers door priority unlock
Drivers door only unlocks on first press of Disarm/Unlock,
All doors unlock on second press within 5 seconds. .................................................................................. Off
2 – Ignition lock
All doors lock when ignition key is turned to on (run). ................................................................................ Off
3 – Ignition unlock
All doors are unlocked when ignition key is turned to off. .......................................................................... Off
4 – Delayed door lock for ignition lock
Waits 3 seconds after key on event before activating ignition locked.
Used on vehicles with theater dimming interior lights. ............................................................................... Off
5 – Illuminated exit
Activates dome light output for one minute when ignition key is turned off ................................................ On
6 – Horn used for alarm
Horn sounds during alarm/panic cycles ..................................................................................................... On
7 – Noise control
Limits alarm trips to 5 per zone .................................................................................................................. On
8 – Factory RKE system does not arm alarm
Prevents factory RKE from arming security system. Still allows
factory RKE to disarm security system. ...................................................................................................... Off
Option Bank 3 – 6 chirps
Factory setting
1 – Headlight Output time (used only when option #4 below is in the LED Off position)
LED On – 20 seconds, LED Off – .5 seconds ........................................................................................... On (20 sec.)
2 –Auxilliary Output Time
LED On – .5 seconds, LED Off – Time held .............................................................................................. On (.5 sec.)
3 – Power sliding Door Output Time (used only when option #4 is in the LED On position)
LED On – .5 seconds, LED Off – Time held .............................................................................................. On (.5 sec.)
4 – Convert headlight output to act as power sliding door output
(controlled by pressing the Find/Panic and Headlight buttons simultaneously)
LED On - Power Sliding Door Output, LED Off - Headlight Output ........................................................... Off
Option Bank 4 – 7 chirps
1 – Door ajar switch input polarity
LED On – Positive, LED Off – Negative ..................................................................................................... On (Positive)
2 – Unlock switch sense input polarity
LED On – Positive, LED Off – Negative ..................................................................................................... On (Positive)
3 – Door ajar input entry delay
5 Second entry delay. Used for vehicles with external door mounted RKE keypads ................................. Off
4 – Use trunk relay as Driver door unlock
Switches Trunk release and Drivers door unlock outputs ........................................................................... Off
34/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
RKE/VSS & VSS OPTION CHART
Option Bank 1 – 4 chirps
Factory setting
1 – Lite-touch adjustment
2 – Full shock adjustment
3 – Optional alarm disable
Disables security functionality. .................................................................................................................... Off
4 – Passive starter Interrupt
Starter interrupt activates 1 minutes after key off event. ............................................................................ Off
5 – Passive arming
Security system activates 1 minutes after key off event. ............................................................................ Off
6 – Passive door locks
All doors lock automatically 1 minutes after key off event. ......................................................................... Off
7 – Selectable chirps
Enables arming/disarming confirmation chirps (uses horn). ...................................................................... On
8 – Silent choice
On – Confirmation chirp on second press of transmitter button
Off – Confirmation chirp on first press of transmitter button.
Requires option #7 (above) to be ON. ........................................................................................................ On
Option Bank 2 – 5 chirps
Factory setting
1 – Drivers door priority unlock
Drivers door only unlocks on first press of Disarm/Unlock,
All doors unlock on second press within 5 seconds. .................................................................................. Off
2 – Ignition lock
All doors lock when ignition key is turned to on (run). ................................................................................ Off
3 – Ignition unlock
All doors are unlocked when ignition key is turned to off. .......................................................................... Off
4 – Delayed door lockfor ignition lock
Waits 3 seconds after key on event before activating ignition locked.
Used on vehicles with theater dimming interior lights. ............................................................................... Off
5 – Illuminated exit
Activates dome light output for one minute when ignition key is turned off ................................................ On
6 – Horn used for alarm
Horn sounds during alarm/panic cycles ..................................................................................................... On
7 – Noise control
Limits alarm trips to 5 per zone .................................................................................................................. On
8 – Factory RKE system does not arm alarm
Prevents factory RKE from arming security system. Still allows
factory RKE to disarm security system. ...................................................................................................... Off
Option Bank 3 – 6 chirps
Factory setting
1 – Door ajar switch input polarity
LED On – Positive, LED Off – Negative ..................................................................................................... On (Positive)
2 – Unlock switch sense input polarity
LED On – Positive, LED Off – Negative ..................................................................................................... On (Positive)
3 – Door ajar input entry delay
5 Second entry delay. Used for vehicles with external door mounted RKE keypads ................................. Off
4 – Use trunk relay as Driver door unlock
Switches Trunk release and Drivers door unlock outputs ........................................................................... Off
35/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
RKE OPTION CHART
Option Bank 1 – 4 chirps
Factory setting
1 – Lite-touch adjustment
2 – Full shock adjustment
3 – Optional alarm disable
Disables security functionality. .................................................................................................................... Off
4 – Passive starter Interrupt
Starter interrupt activates 1 minutes after key off event. ............................................................................ Off
5 – Passive arming
Security system activates 1 minutes after key off event. ............................................................................ Off
6 – Passive door locks
All doors lock automatically 1 minutes after key off event. ......................................................................... Off
7 – Selectable chirps
Enables arming/disarming confirmation chirps (uses horn). ...................................................................... On
8 – Silent choice
On – Confirmation chirp on second press of transmitter button
Off – Confirmation chirp on first press of transmitter button.
Requires option #7 (above) to be ON. ........................................................................................................ On
Option Bank 2 – 5 chirps
Factory setting
1 – Drivers door priority unlock
Drivers door only unlocks on first press of Disarm/Unlock,
All doors unlock on second press within 5 seconds. .................................................................................. Off
2 – Ignition lock
All doors lock when ignition key is turned to on (run). ................................................................................ Off
3 – Ignition unlock
All doors are unlocked when ignition key is turned to off. .......................................................................... Off
4 – Delayed door lock for ignition lock
Waits 3 seconds after key on event before activating ignition locked.
Used on vehicles with theater dimming interior lights. ............................................................................... Off
5 – Illuminated exit
Activates dome light output for one minute when ignition key is turned off ................................................ On
6 – Horn used for alarm
Horn sounds during alarm/panic cycles ..................................................................................................... On
7 – Noise control
Limits alarm trips to 5 per zone .................................................................................................................. On
Option Bank 3 – 6 chirps
Factory setting
1 – Door ajar switch input polarity
LED On – Positive, LED Off – Negative ..................................................................................................... On (Positive)
2 – Use trunk relay as Driver door unlock
Switches Trunk release and Drivers door unlock outputs ........................................................................... Off
36/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
LOT MODE ONLY OPTION CHART
Option Bank 1 – 4 chirps
Factory setting
1 – Lite-touch adjustment
2 – Full shock adjustment
3 – Optional alarm disable
Disables security functionality. .................................................................................................................... Off
4 – Passive starter Interrupt
Starter interrupt activates 1 minutes after key off event. ............................................................................ Off
5 – Passive arming
Security system activates 1 minutes after key off event. ............................................................................ Off
6 – Passive door locks
All doors lock automatically 1 minutes after key off event. ......................................................................... Off
7 – Selectable chirps
Enables arming/disarming confirmation chirps (uses horn). ...................................................................... On
8 – Silent choice
On – Confirmation chirp on second press of transmitter button
Off – Confirmation chirp on first press of transmitter button.
Requires option #7 (above) to be ON. ........................................................................................................ On
Option Bank 2 – 5 chirps
Factory setting
1 – Drivers door priority unlock
Drivers door only unlocks on first press of Disarm/Unlock,
All doors unlock on second press within 5 seconds. .................................................................................. Off
2 – Delayed door lock for ignition lock
Waits 3 seconds after key on event before activating ignition locked.
Used on vehicles with theater dimming interior lights. ............................................................................... Off
3 – Horn used for alarm
Horn sounds during alarm/panic cycles ..................................................................................................... On
4 – Noise control
Limits alarm trips to 5 per zone .................................................................................................................. On
Option Bank 3 – 6 chirps
Factory setting
1 – Tach Diagnostic Mode
Car start function ignores tach input, cranks starter one time for one second.
WARNING – Over rev and stall detection is disabled. ................................................................................ Off
2 – Car start run time
LED On – 15 minutes, LED Off – 10 minutes ............................................................................................ Off
3 – Lock after start
(Re)locks doors after remote start. ............................................................................................................. Off
4 – One button start
Activates remote start by press and hold of start button. ........................................................................... Off
5 – Diesel timer
Delays crank attempt 30 seconds after ignition on. .................................................................................... Off
Factory setting
Option Bank 4 – 7 chirps
1 – Door ajar switch input polarity
LED On – Positive, LED Off – Negative ..................................................................................................... On (Positive)
3 – Key-in sense input polarity
LED On – Positive, LED Off – Negative ..................................................................................................... Off (Negative)
5 – Use trunk relay as Driver door unlock
Switches Trunk release and Drivers door unlock outputs ........................................................................... Off
6 – Learn tachometer
With hood open or brake pedal pressed start engine. System will chirp horn
every five seconds if a valid tach signal is present.
37/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
WIRING HARNESS LEGEND
B
1
2
3
4
5
10 11 12 13
6
7
8
9
14 15 16
B
A
EXTENDED FUNCTION
CAR START
MAIN HARNESS
1
2
3
4
5
6
7
13 14 15 16 17 18
9 10 11 12
1
19 20 21 22 23 24
8
7
2
3
4
5
6
9 10
8
WIRE END VIEWS
Car Start Harness (10-way)
Main Harness (24-way)
Terminal Wire Color
A-1
WHITE
Function
Terminal
Wire Color
Function
Parking Light Output
B-1
BLUE
HVAC2 Feed
RED
HVAC1 Feed
A-2
BLUE
Door Lock Output
B-2
A-3
BLACK/WHITE
Dome Light Output
B-3
PINK/WHITE
Ignition 2 Output
A-4
RED
Battery
B-4
ORANGE
HVAC 1 Output
A-5
BLACK
Ground
B-5
ORANGE/WHITE
HVAC 2 Output
A-6
VIOLET/RED
Starter Interrupt (Key
side)
B-6
Open
-
B-7
BROWN
Brake Input
A-7
PINK
Ignition 1 Input/Output
B-8
BLACK/WHITE
Key-in-sense Input
B-9
VIOLET/WHITE
Tach Sense Input
A-8
VIOLET
Starter Interrupt (Motor
side)
B-10
BLUE/BLACK
Active Out
A-9
BROWN
Disarm Input
Extended Function Harness (16-way)
A-10
YELLOW/WHITE
Door Trigger Input Pullup
Terminal
A-11
WHITE/BLUE
Arm Input
A-12
LT.GREEN
A-13
Wire Color
Function
C-1
BLUE/BLACK
Door Lock Switch Input
C-2
BLACK/GREEN
AUX 3
Unlock Switch Sense
Input
C-3
GREEN/BLACK
Door Unlock Switch
Input
TAN
Trunk Release/Driver
Door Unlock Release
Output
C-4
LT.GREEN/BLACK
Factory Perimeter
Alarm Disarm Output
C-5
Open
-
A-14
GREEN
Door Unlock Output
C-6
Open
-
A-15
RED
Siren Feed
C-7
BROWN/TAN
A-16
BLACK
Siren Output
Trunk Release Disarm
Input
A-17
BROWN
Programming/Override
Button
C-8
BLUE
Trunk Ajar Input
C-9
TAN/RED
Trunk Release/Driver
Door Unlock Switch
Input
A-18
BROWN
Programming/Override
Button
A-19
GRAY
Hood Open Switch
Input
C-10
RED/WHITE
Headlight Output /
AUX 1
A-20
GREEN/VIOLET
Door Ajar Switch Input
C-11
BLUE/WHITE
A-21
BROWN/BLACK
Horn Relay Output
Rear Defroster Output
/ AUX 2
A-22
RED
LED
C-12
GREEN/WHITE
Memory 1 Output
A-23
BLACK
LED
C-13
YELLOW/GREEN
Memory 2 Output
A-24
BLUE/GREEN
(-) Drivers Door
Unlock/Trunk release
Output
C-14
Open
-
C-15
Open
-
C-16
Open
-
38/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
Circuit Testing - Identifying Circuit Polarity
1
Digital Volt Meter (DVM) set to “DC Volts”.
Negative lead (Black) connected to a chassis ground.
Positive lead (Red) connected to circuit under test.
Observe reading from meter.
DC Volts
2
3
Actuate the circuit under test.
Observe reading from meter.
A reading of 0V transiting to +12V when the switch is
pressed, indicates that the circuit under test is a
Positive polarity circuit.
A reading of +12V transiting to 0V when the switch is
pressed, indicates that the circuit under test is a
Negative polarity circuit.
!
0V
12V
0V
NOTE: When testing a Negative polarity circuit,
the stand by voltage will not always be +12V. In
some cases the reading observed prior to
actuating the circuit could be less than one (1)
volt. However, when actuated the observed
voltage will be 0V or very close to it.
POSITIVE
POLARITY
CIRCUIT
39/42
12V
2W7Z-16A901-AA
SK5W7J-19A361-AA
NEGATIVE
POLARITY
CIRCUIT
© Copyright Ford 2005
Rev Date- 8/29/05
Wire Connection Procedures
1
Inline wire splice procedure
Wire From
Powercode
Harness
Cut Target Wire
In Vehicle
Heat Shrint Tubing
Wih Hot Melt Wax
NOTE: TO INSURE PROPER INSTALLATION, USE THE FOLLOWING GUIDELINES:
APPLY FLOCK TAPE TO SHARP OR JAGGED AREAS DURING INSTALLATION OF WIRE HARNESS
APPLY FLOCK TAPE TO WIRENESS IN AREAS WHERE SQUEAK AND RATTLE CONDITIONSMAY OCCUR, i.e. CONNECTORS
SECURE WIREHARNESS AT LEAST 6MM FROM EXISTING SENSORS OR MODULES
SECURE WIRE HARNESS AT LEAST 19MM FROM MOVING PARTS, i.e. VACUUM MOTORS, etc.
NOTE: IF AN UNRELIABLE METHOD OF WIRE SPLICING IS USED WHEN INSTALLING ELECTRICAL ADD-ON EQUIPMENT, IT MAY
CAUSE ELECTRICAL SYSTEMS TO MALFUNCTION BY CREATING VARIABLE RESISTANCE OR A SHORT CIRCUIT. VARIABLE
RESISTANCECAN RESULT FROM OXIDATION/COROSION CAUSED BY AIR WITHIN THE JOINT AND A SHORT CIRCUIT CAN
RESULT FROM THE MOISTURE ON THE JOINT
HEAT SHRINK TUBING MUST CONTAIN HOT MELT WAX. THIS WILL CREATE A WATERPROOF AND AIRTIGHT JOINT.
SOLDER MUST BE ROSIN CORE MILDLY ACTIVATED (RMA). DO NOT USE ACID CORE SOLDER.
DO NOT USE CRIMP-CONNECTORS OF ANY KIND. THEY ARE NOT A ROBUST METHOD FOR SPLICING IN NEW WIRES.
40/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
Wire Connection Procedures
2
Ended Wire Splice Procedure
Wire From
Powercode
Harness
Cut Target Wire
In Vehicle
Heat Shrink Tubing
With Hot Melt Wax
NOTE: TO INSURE PROPER INSTALLATION, USE THE FOLLOWING GUIDELINES:
APPLY FLOCK TAPE TO SHARP OR JAGGED AREAS DURING INSTALLATION OF WIRE HARNESS
APPLY FLOCK TAPE TO WIRENESS IN AREAS WHERE SQUEAK AND RATTLE CONDITIONSMAY OCCUR, i.e. CONNECTORS
SECURE WIREHARNESS AT LEAST 6MM FROM EXISTING SENSORS OR MODULES
SECURE WIRE HARNESS AT LEAST 19MM FROM MOVING PARTS, i.e. VACUUM MOTORS, etc.
NOTE: IF AN UNRELIABLE METHOD OF WIRE SPLICING IS USED WHEN INSTALLING ELECTRICAL ADD-ON EQUIPMENT, IT MAY
CAUSE ELECTRICAL SYSTEMS TO MALFUNCTION BY CREATING VARIABLE RESISTANCE OR A SHORT CIRCUIT. VARIABLE
RESISTANCECAN RESULT FROM OXIDATION/COROSION CAUSED BY AIR WITHIN THE JOINT AND A SHORT CIRCUIT CAN
RESULT FROM THE MOISTURE ON THE JOINT
HEAT SHRINK TUBING MUST CONTAIN HOT MELT WAX. THIS WILL CREATE A WATERPROOF AND AIRTIGHT JOINT.
SOLDER MUST BE ROSIN CORE MILDLY ACTIVATED (RMA). DO NOT USE ACID CORE SOLDER.
DO NOT USE CRIMP-CONNECTORS OF ANY KIND. THEY ARE NOT A ROBUST METHOD FOR SPLICING IN NEW WIRES.
41/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
© Copyright Ford 2005
Rev Date- 8/29/05
SK5W7J-19A361-AA
VEHICLE SPECIFIC WIRING DIAGRAMS
1
2
This section presents Vehicle/Product specific wiring diagrams are provided for all systems. The diagrams are organized by
vehicle (Year/Model) and by Product. For example, to find a specific wiring diagram for installing a RKE/VSS/RMST system in
a 2002 Explorer Sport:
1. In the Bookmarks pane, click on the “+” symbol to the left of the bookmark for “2002MY”.
2. Click on the “+” symbol to the left of the bookmark for for “Explorer Sport/Sport Trac.
3. Select the system that you are installing in the links revealed under Explorer Sport/Sport Trac.
4.
Then using the
A
Title block:
Box 1: Lists applicable vehicle(s) by year/make/model;
Box 2: Lists any vehicle trim level or special equipment required on the vehicle. This will generally be: ALL, w/Factory
RKE or w/o Factory RKE. Note: If you are working on a vehicle with factory RKE, a drawing that lists “w/o RKE”
in this box does not apply to this installation. Conversely, if you are working on a vehicle without factory RKE,
disregard the drawings listing “w/Factory RKE” in this box.;
Box 3: Lists the system or systems covered by this drawing (System name --> Short name used in title block);
• Remote Start System with Deluxe Vehicle Security and Keyless Entry —> RKE/VSS/RMST
• Remote Start System with Keyless Entry —> RKE/RMST
• Remote Start System —> RMST
• Deluxe Vehicle Security System with Keyless Entry —> Deluxe RKE/VSS (shown in graphic below)
• Vehicle Security System with Keyless Entry —> RKE/VSS
• Vehicle Security System for Vehicles Equipped with Factory Keyless Entry —> VSS
• Keyless Entry System —> RKE
Box 4: Page number and total number of pages which make up the complete drawing;
Box 5: Revision date of drawing.
Lists the systems wires by Connector/Terminal, Wire color, and function.
B
C
D
E
buttons in the Acrobat toolbar, you can view the individual pages in the drawing.
Lists the vehicle circuit by the vehicle wire color and circuit polarity - Circuit name (wire color) + or
(indicates
vehicle’s circuit polarity).
List the circuit location in the vehicle. Clicking on the text will open another window showing a color photograph of the
circuit location in the vehicle (internet connection required).
Optional connections - clicking on the “Optional installation feature” text, will jump to a diagram showing the connection
of the optional circuit. Clicking on the “Go to Previous View” button will return to the original page.
Vehicle (Year/Make/Model)
Box 1
Box 2
Box 4
’02/’03 Explorer Sport / Sport Trac
Equipment or Trim level
System(s) applicable to:
w/Factory RKE
Deluxe RKE/VSS
Page
Revision Date
1 of 4
7/30/02
A
Box 3
Box 5
MAKE THIS CONNECTION FIRST!
CHASSIS GROUND POINT
IN DRIVERS KICK PANEL
Dome Light (BLACK/BLUE) +
DRIVERS SIDE KICK PANEL
A-5
A-20
A-3
A-2
A-14
A-12
A-11
C-4
A-9
A-24
Door Lock (PINK/YELLOW)
Color
Function
BLACK
GREEN/VIOLET
BLACK/WHITE
BLUE
GREEN
LT.GREEN
WHITE/BLUE
LT GREEN/BLACK
BROWN
BLUE/GREEN
Ground
Door Ajar Switch Input
Dome Light Output
Door Lock Output
Door Unlock Output
Unlock Switch Sense Input
Arm Input
Factory alarm disarm output
Disarm Input
Driver Door Unlock Output
B
C
Door Unlock (PINK/GREEN)
D
HARNESS UNDER
DRIVERS SIDE
DOOR SILL PLATE
Lock Motor (PINK/BLACK) +
Driver Door Ajar Switch
(YELLOW/BLACK)
Driver Door Unlock Motor
(RED/ORANGE) +
DRIVER DOOR
JAMB BOOT
HARNESS
Optional Installation Feature
See Optional connections page
Cut and tape off if not used
42/42
2W7Z-16A901-AA
SK5W7J-19A361-AA
E
© Copyright Ford 2005
Rev Date- 8/29/05