Fortinet 100 Network Card User Manual

LED
Power
Display Panel LEDs:
1, 2, 3, 4
5/HA, INT, EXT
Port 1
Internal, External
State
Description
Green
The FortiGate unit is on.
Off
The FortiGate unit is off.
Green
The correct cable is in use and the connected equipment has power.
Flashing
Green
Network activity at this interface.
Off
No link established.
Amber
The link is up.
Flashing
Amber
Network activity at this interface.
Green
Link speed is 100Mb/s
Off
Link speed is 10Mb/s
Amber
The link is up.
Flashing
Amber
Network activity at this interface.
Green
Link speed is 1000Mb/s
Off
Link speed is 100Mb/s
Esc
POWER
1
2
3
Hi-Temp
4
5/HA
INT
Enter
2
1
3
4
5/HA
INTERNAL
EXT
EXTERNAL
FortiGate-3600
© Copyright 2009 Fortinet Incorporated. All rights reserved.
Products mentioned in this document are trademarks or registered trademarks of their respective holders.
Regulatory Compliance
FCC Class A Part 15 CSA/CUS
23 January 2009
01-30006-0041-20090123
Checking the Package Contents
Front
Connector
Type
Speed
Protocol
Description
Internal
SC
1000Base-SX
Ethernet
Copper gigabit connection to the internal
network.
External
SC
1000Base-SX
Ethernet
Copper gigabit connection to the internet.
Port 1
RJ-45
10/100Base-T
Ethernet
Optional connection to a 10/100Base-T network.
Port 2 to 4
SC
1000Base-SC
Ethernet
Optional multimode fiber optic connections to
other networks.
Port 5/HA
SC
1000Base-SC
Ethernet
Optional multimode fiber optic connection to another network, or to other FortiGate-3600 units
for high availability (HA).
CONSOLE
DB-9
9600 bps
RS-232
serial
Esc
POWER
1
2
3
Hi-Temp
4
5/HA
INT
Ethernet Cables:
Orange - Crossover
Grey - Straight-through
Enter
2
1
3
4
5/HA
INTERNAL
EXT
EXTERNAL
Null-Modem Cable
(RS-232)
LCD
Display
Control
Buttons
1, 2, 3, 4, 5/HA Internal External
Interfaces
Interface Interface
Power Cables (2)
Back
Rack-Mount Brackets
Power
Supply
LEDs
Optional connection to the management computer. Provides access to the command line
interface (CLI).
QuickStart Guide
Esc
POWER
1
Hi-Temp
4
2
3
5/HA
INT
Enter
1
2
3
4
5/HA
INTERNAL
EXT
EXTERNAL
FortiGate-3600
Alarm
Cancel
RS-232 Serial Button Redundant
Hot Swappable
Connection
Power Supplies
Redundant
Hot-Swappable
Fan Assemblies
Copyright 2006 Fortinet Incorporated. All rights reserved.
Trademarks
Products mentioned in this document are trademarks.
Documentation
Connecting
Connect the FortiGate unit to a power outlet and to the internal and external networks.
•
Place the unit on a stable surface.
•
The FortiGate unit requires 1.5 inches (3.75 cm) clearance above and on each side to
allow for cooling.
Optional null modem cable connects
to serial port on management computer
Esc
1
•
Make sure the power switch on the back of the unit is turned off before connecting the
power and network cables.
•
MAIN MENU appears when the unit is up and running.
•
If only one power supply is connected, an audible alarm sounds to indicate a failed
power supply. To stop this alarm, press the red alarm cancel button.
POWER
1
2
3
Hi-Temp
4
5/HA
INT
Enter
2
3
Straight-through Ethernet cable connects
to another network
4
5/HA
INTERNAL
or
EXT
EXTERNAL
Straight-through Ethernet cable connects
to Internet (public switch, router or modem)
SC fiber optic cables connect to other networks
Power cables connect to power outlets
Crossover Ethernet cable connects to management computer on internal network
Straight-through Ethernet cable connects to LAN or switch on internal network
Planning the Configuration
Before beginning to configure the FortiGate unit, you need to plan how to integrate the unit into your network. Your configuration plan is dependent upon the operating mode that you select:
NAT/Route mode (the default) or Transparent mode. Refer to the Documentation CD-ROM for information on how to control traffic, and how to configure HA, antivirus protection, FortiGuard,
Web content filtering, Spam filtering, intrusion prevention (IPS), and virtual private networking (VPN).
NAT/Route mode
Transparent mode
In NAT/Route mode, each FortiGate unit is visible to the network that it is connected to. All
of its interfaces are on different subnets. Each interface connected to a network must be
configured with an IP address that is valid for that network.
In Transparent mode, the FortiGate unit is invisible to the network. All of its interfaces are on
the same subnet. You only have to configure a management IP address so that you can make
configuration changes.
You would typically use NAT/Route mode when the FortiGate unit is deployed as a gateway
between private and public networks. In its default NAT/Route mode configuration, the unit
functions as a firewall. Firewall policies control communications through the FortiGate unit.
No traffic can pass through the FortiGate unit until you add firewall policies.
You would typically use the FortiGate unit in Transparent mode on a private network behind
an existing firewall or behind a router. In its default Transparent mode configuration, the unit
functions as a firewall. No traffic can pass through the FortiGate unit until you add firewall
policies.
In NAT/Route mode, firewall policies can operate in NAT mode or in Route mode. In NAT
mode, the FortiGate unit performs network address translation before IP packets are sent to
the destination network. In Route mode, no translation takes place.
You can connect up to four network segments to the FortiGate unit to control traffic between
these network segments.
DMZ network
Internal Network
192.168.1.3
Web Server
Routing policies controlling
traffic between internal
networks.
Internal
192.168.1.99
External
204.23.1.5
Internet
Port 1
10.10.10.1
Internal
network
Router
Port 1
External
Internet
Router
Internal
Hub or switch
10.10.10.2
NAT mode policies controlling
traffic between internal
and external networks.
Mail Server
Internal
network
Choosing a Configuration Tool
Web-based manager
Command Line Interface (CLI)
The FortiGate web-based manager is an easy to use management tool.
Use it to configure the administrator password, the interface and default gateway addresses,
and the DNS server addresses.
The CLI is a full-featured management tool. Use it to configure the administrator password,
the interface addresses, the default gateway address, and the DNS server addresses. To
configure advanced settings, see the Documentation CD-ROM.
Requirements:
•
An Ethernet connection between the FortiGate unit and management computer.
•
Internet Explorer 6.0 or higher on the management computer.
Requirements:
•
The DB-9 serial connection between the FortiGate unit and management computer.
•
A terminal emulation application (HyperTerminal for Windows) on the management
computer.
Collecting Information
NAT/Route Mode
Internal
External
Port 1
Port 2
Port 3
Port 4
Port 5/HA
Transparent mode
IP:
____.____.____.____
Netmask:
____.____.____.____
IP:
____.____.____.____
Netmask:
____.____.____.____
IP:
____.____.____.____
Netmask:
____.____.____.____
IP:
____.____.____.____
Netmask:
____.____.____.____
IP:
____.____.____.____
Netmask:
____.____.____.____
IP:
____.____.____.____
Netmask:
____.____.____.____
IP:
____.____.____.____
Netmask:
____.____.____.____
The internal interface IP address and netmask must be valid for the internal network.
Management IP
IP:
____.____.____.____
Netmask:
____.____.____.____
The management IP address and netmask must be valid for the network from which you will
manage the FortiGate unit.
General settings
Administrator password
Network Settings
Default Gateway:
____.____.____.____
Primary DNS Server:
____.____.____.____
Secondary DNS Server:
____.____.____.____
A default gateway is required for the FortiGate unit to route connections to the Internet.
Factory default settings
NAT/Route mode
Transparent mode
Internal interface
192.168.1.99
Management IP
External interface
192.168.100.99
Administrative account settings
Ports 1 to 5
0.0.0.0
User name
admin
Password
(none)
DHCP server on Internal interface
0.0.0.0
192.168.1.110 – 192.168.1.210
Configuring the FortiGate Unit
Web-based Manager
Command Line Interface
1.
1.
2.
3.
4.
Connect the FortiGate internal interface to a management computer Ethernet interface.
Use a cross-over Ethernet cable to connect the devices directly. Use straight-through
Ethernet cables to connect the devices through a hub or switch.
Configure the management computer to be on the same subnet as the internal
interface of the FortiGate unit. To do this, change the IP address of the management
computer to 192.168.1.2 and the netmask to 255.255.255.0.
To access the FortiGate web-based manager, start Internet Explorer and browse to
https://192.168.1.99 (remember to include the “s” in https://).
Type admin in the Name field and select Login.
NAT/Route mode
To change the administrator password
1. Go to System > Admin > Administrators.
2. Select Change Password for the admin administrator and enter a new password.
To configure interfaces
1. Go to System > Network > Interface.
2. Select the edit icon for each interface to configure.
3. Set the addressing mode for the interface. (See the online help for information.)
•
For manual addressing, enter the IP address and netmask for the interface.
•
For DHCP addressing, select DHCP and any required settings.
•
For PPPoE addressing, select PPPoE, and enter the username and password
and any other required settings.
To configure the Primary and Secondary DNS server IP addresses
1. Go to System > Network > Options, enter the Primary and Secondary DNS IP addresses that you recorded above and select Apply.
To configure a Default Gateway
1. Go to Router > Static and select Edit icon for the static route.
2. Set Gateway to the Default Gateway IP address you recorded above and select OK.
Transparent mode
To switch from NAT/route mode to transparent mode
1. Go to System > Config > Operation Mode and select Transparent.
2. Set the Management IP/Netmask to 192.168.1.99/24.
3. Set a default Gateway and select Apply.
To change the administrator password
1. Go to System > Admin > Administrators.
2. Select Change Password for the admin administrator and enter a new password.
To change the management interface
1. Go to System > Config > Operation Mode.
2. Enter the Management IP address and netmask that you recorded above and select
Apply.
To configure the Primary and Secondary DNS server IP addresses
1. Go to System > Network > Options, enter the Primary and Secondary DNS IP addresses that you recorded above and select Apply.
7
2.
3.
4.
Use the DB9 serial cable to connect the FortiGate Console port to the management
computer serial port.
Start a terminal emulation program (HyperTerminal) on the management computer. Use
these settings:
Baud Rate (bps) 9600, Data bits 8, Parity None, Stop bits 1, and Flow Control None.
At the Login: prompt, type admin and press Enter twice (no password required).
NAT/Route mode
1.
2.
3.
4.
Configure the FortiGate internal interface.
config system interface
edit internal
set ip <intf_ip>/<netmask_ip>
end
Repeat to configure each interface, for example, to configure the WAN1 interface.
config system interface
edit wan1
...
Configure the primary and secondary DNS server IP addresses.
config system dns
set primary <dns-server_ip>
set secondary <dns-server_ip>
end
Configure the default gateway.
config router static
edit 1
set gateway <gateway_ip>
end
Transparent Mode
1.
2.
Change from NAT/Route mode to Transparent mode and configure the Management IP
address.
config system settings
set opmode transparent
set ip <mng_ip>/<netmask>
set gateway <gateway_ip>
end
Configure the DNS server IP address.
config system dns
set primary <dns-server_ip>
set secondary <dns-server_ip>
end
Completing the Configuration
Congratulations!
You have finished configuring the basic settings. Your network is now protected from Internetbased threats. To explore the full range of configuration options, see the online help or the
Documentation CD-ROM.
Visit these links for more information and documentation for your Fortinet product.
• Technical Documentation - http://docs.forticare.com
• Fortinet Knowledge Center - http://kc.forticare.com
• Fortinet Technical Support - http://support.fortinet.com
Download PDF

advertising