Operating instructions | Franke Consumer Products FLAT 604 Convection Oven User Manual

Gas
Range
Visit the Frigidaire Web Site at: http://www.frigidaire.com
ES100 Control with Gas Sealed Burners
& Broiler Drawer
Welcome.......................................... 2
Important Safety Instructions .....2-4
Setting Surface Controls ............... 5
Before Setting Oven Controls ....... 6
Oven Control Functions .............6-7
Setting Oven Controls .................8-9
Adjusting Your Oven
Temperature (some models) .......... 10
General Care & Cleaning ........ 11-13
Before You Call
Solutions to Common Problems ........................ 14
Warranty ......................... Back Page
Questions or for Service Call:
1-800-944-9044 (U.S.)
1-800-668-4606 (Canada)
READ AND SAVE THESE INSTRUCTIONS
p/n 316417139 (0803)
Welcome & Congratulations
Congratulations on your purchase of a new range! At Electrolux Home
Products, we are very proud of our product and are completely committed to
providing you with the best service possible. Your satisfaction is our number
one priority.
We know you’ll enjoy your new range and Thank You for choosing our product.
We hope you consider us for future purchases.
PLEASE CAREFULLY READ AND SAVE THESE INSTRUCTIONS
This Use & Care Manual provides specific operating instructions for your model.
Use your appliance only as instructed in this manual. These instructions are
not meant to cover every possible condition or situation that may occur.
Common sense & caution must be practiced when installing, operating &
maintaining any appliance.
Please record your model and serial numbers below for future
reference.
Model Number:
Serial Number:
Serial plate is located behind the broil or
storage drawer on the lower right side of
the appliance frame.
Purchase Date:
This Use & Care Manual contains general operating instructions for your
appliance and feature information for several models. Your range may not have
all the described features. The graphics shown are representative. The graphics
on your range may not look exactly like those shown.
Product Registration
Be sure to register your product. The self-addressed PRODUCT
REGISTRATION CARD should be filled in completely, signed and returned to
Electrolux Home Products.
Important Safety Instructions
Grounding Instructions
(electric ignition models only)
Avoid fire hazard or electrical shock. Do not use an adapter plug,
an extension cord, or remove grounding prong from electrical power cord. Failure
to follow this warning can cause serious injury, fire or death.
This appliance is equipped with a 3-prong grounding plug for your
protection against shock hazard and should be plugged directly into a properly
grounded receptacle. DO NOT cut or REMOVE the grounding prong from this plug.
For personal safety this appliance must be properly grounded. For maximum
safety, the power cord must be plugged into an electrical outlet that is correctly
polarized and properly grounded.
If a 2-prong wall receptacle is the only available outlet, it is the personal
responsibility of the consumer to have it replaced with a properly grounded 3-prong
wall receptacle installed by a qualified electrician.
© 2008 Electrolux Home Products, Inc.
All rights reserved.
2
See the INSTALLATION
INSTRUCTIONS packaged with this
appliance for complete installation &
grounding instructions.
Important Safety Instructions
Read all instructions before using this appliance.
Save these instructions for future reference.
This manual contains important safety symbols and instructions. Please pay attention to these symbols and follow all instructions given.
This symbol will help alert you to situations that may cause serious bodily harm, death or property damage.
This symbol will help alert you to situations that may cause bodily injury or property damage.
If the information in this manual is not
followed exactly, a fire or explosion may result causing
property damage, personal injury or death.
FOR YOUR SAFETY:
— Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
— WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phone in your building.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the fire
department.
— Installation and service must be performed by a
qualified installer, servicer or the gas supplier.
• Remove all tape and packaging before using the range.
Destroy the carton and plastic bags after unpacking the
range. Never allow children to play with packaging material.
• Proper Installation—Be sure your appliance is properly
installed and grounded by a qualified technician in
accordance with the National Fuel Gas Code ANSI
Z223.- latest edition, or in Canada CAN/CGA B149.1, and
CAN/CGA B149.2, and the the National Electrical Code
ANSI/NFPA No.70-latest edition, or in Canada CSA
Standard C22.1, Canadian Electrical Code, Part 1, and
local code requirements. Install only per installation
instructions provided in the literature package for this range.
Ask your Sears dealer to recommend a qualified technician
and an authorized Sears repair service. Know how to disconnect
the power to the range at the circuit breaker or fuse box in
case of an emergency.
• User servicing—Do not repair or replace any part of the
appliance unless specifically recommended in the
manuals. All other servicing should be done only by a
qualified technician, This may reduce the risk of personal
injury and damage to the range.
• Never modify or alter the construction of a range by
removing leveling legs, panels, wire covers, anti-tip
brackets/screws, or any other part of the product.
• Air curtain or other overhead range hoods, which
operate by blowing a downward air flow on to a range,
shall not be used in conjunction with gas ranges other
than when the hood and range have been designed,
tested and listed by an independent test laboratory for
use in combination with each other.
Stepping, leaning or sitting on the doors
or drawers of this range can result in serious injuries
and also cause damage to the range. Do not allow
children to climb or play around the range. The weight of a child
on an open door may cause the range to tip, resulting in
serious burns or other injury.
NEVER use this appliance as a space
heater to heat or warm the room. Doing so may result in
carbon monoxide poisoning.
NEVER cover any slots, holes or passages
in the oven bottom or cover an entire rack with materials
such as aluminum foil. Doing so blocks air flow through the
oven and may cause carbon monoxide poisoning. Aluminum foil
linings may trap heat, causing a fire hazard.
Do not use the oven or warmer drawer
(if equipped) for storage.
• Storage in or on Appliance—Flammable materials
should not be stored in an oven, warmer drawer, near
surface burners or in the storage drawer. This includes
paper, plastic and cloth items, such as cookbooks, plasticware
and towels, as well as flammable liquids. Do not store
explosives, such as aerosol cans, on or near the range.
Do not store items of interest to children
in the cabinets above a range or on the backguard of
a range. Children climbing on the range to reach items could
be seriously injured.
3
Important Safety Instructions
• Never Leave Surface Burners Unattended at High Heat
Settings—Boilovers cause smoking and greasy spillovers
that may ignite, or a pan that has boiled dry may melt.
• Protective Liners—Do not use aluminum foil to line surface
burner pans, or oven bottom, except as suggested in this
manual. Improper installation of these liners may result in risk
of electric shock, or fire.
• Glazed Cooking Utensils—Only certain types of glass,
glass/ceramic, ceramic, earthenware, or other glazed utensils
are suitable for cooktop service without breaking due to the
sudden change in temperature. Check the manufacturer’s
recommendations for cooktop use.
IMPORTANT INSTRUCTIONS FOR USING YOUR OVEN
• Use Care When Opening Oven Door or Warmer Drawer—
Stand to the side of the range when opening the door of a hot
oven. Let hot air or steam escape before you remove or
replace food in the oven.
• Keep Oven Vent Ducts Unobstructed. The oven vent is
located below the backguard. Touching the surfaces in this
area when the oven is operating may cause severe burns.
Also, do not place plastic or heat-sensitive items on or near
the oven vent. These items could melt or ignite.
• Placement of Oven Racks. Always place oven racks in
desired location while oven is cool. If rack must be moved
while oven is hot use extreme caution. Use potholders and
grasp the rack with both hands to reposition. Do not let
potholders contact the hot heating elements in the oven.
Remove all utensils from the rack before moving.
• Do not use the broiler pan without its insert. The broiler
pan and its insert allow dripping fat to drain and be kept away
from the high heat of the broiler.
• Do not cover the broiler insert with aluminum foil.
Exposed fat and grease could ignite.
• Cold temperatures can damage the electronic control. When
using the appliance for the first time, or when the appliance
has not been used for an extended period of time, be certain
the unit has been in temperatures above 32°F (0°C) for at least
3 hours before turning on the power to the appliance.
IMPORTANT INSTRUCTIONS FOR CLEANING YOUR
RANGE
• Clean the range regularly to keep all parts free of
grease that could catch fire. Pay particular attention to the
area underneath each surface element. Do not allow grease
to accumulate. Refer to the range manufacturer’s instructions
for cleaning.
• Kitchen cleaners and aerosols—Always follow the
manufacturer’s recommended directions for use. Be
aware that excess residue from cleaners and aerosols may
ignite causing damage and injury.
• Do Not Leave Children Alone—Children should not be
left alone or unattended in the area where appliance is
in use. They should never be allowed to sit or stand on any
part of the appliance.
• DO NOT TOUCH SURFACE BURNERS, AREAS NEAR
THESE BURNERS, OVEN BURNERS OR INTERIOR
SURFACES OF THE OVEN. Both surface and oven burners
may be hot even though flames are not visible. Areas near
surface burners may become hot enough to cause burns.
During and after use, do not touch, or let clothing or other
flammable materials touch these areas until they have had
sufficient time to cool. Among these areas are the cook top,
surfaces facing the cook top, the oven vent openings and
surfaces near these openings, oven door and window.
• Wear Proper Apparel—Loose-fitting or hanging garments
should never be worn while using the appliance. Do not
let clothing or other flammable materials contact hot surfaces.
• Do Not Use Water or Flour on Grease Fires—Smother
the fire with a pan lid, or use baking soda, a dry
chemical or foam-type extinguisher.
• When heating fat or grease, watch it closely. Fat or
grease may catch fire if allowed to become too hot.
• Use Only Dry Potholders—Moist or damp potholders on
hot surfaces may result in burns from steam. Do not let
potholders touch hot heating burners. Do not use a towel or
other bulky cloth instead of a potholder.
• Do Not Heat Unopened Food Containers—Buildup of
pressure may cause container to burst and result in
injury.
• Remove the oven door from any unused range if it is to
be stored or discarded.
IMPORTANT—ELECTRIC IGNITION MODELS ONLY: Do not
attempt to operate the oven during a power failure. If the power
fails, always turn off the oven. If the oven is not turned off and
the power resumes, the oven will begin to operate again. Once
the power resumes, reset the clock and oven function.
IMPORTANT INSTRUCTIONS FOR USING YOUR COOKTOP
Use Proper Flame Size—Adjust flame size
so it does not extend beyond the edge of the utensil. The use
of undersized utensils will expose a portion of the burner flame
to direct contact and may result in ignition of clothing. Proper
relationship of utensil to flame will also improve efficiency.
• Know which knob controls each surface burner. Place a
pan of food on the burner before turning it on, and turn the
burner off before removing the pan.
•Always turn knob to the full LITE position when igniting
top burners. Visually check that burner has lit. Then adjust
the flame so it does not extend beyond the edge of the utensil.
• Utensil Handles Should Be Turned Inward and Not
Extend Over Adjacent Surface Burners—To reduce the
risk of burns, ignition of flammable materials, and spillage due
to unintentional contact with the utensil, the handle of the
utensil should be positioned so that it is turned inward, and
does not extend over adjacent surface burners.
IMPORTANT SAFETY NOTICE
The California Safe Drinking Water and Toxic Enforcement Act
requires the Governor of California to publish a list of substances
known to the state to cause cancer, birth defects or other
reproductive harm, and requires businesses to warn customers
of potential exposure to such substances.
4
Setting Surface Controls
Do not place plastic
items such as salt and pepper
shakers, spoon holders or plastic
wrappings on top of the range when
it is in use. These items could melt or
ignite. Potholders, towels or wood
spoons could catch fire if placed too
close to a flame.
In the event of an electrical power
outage, the surface burners can be lit
manually. To light a surface burner, hold
a lit match to the burner head, then
slowly turn the Surface Control knob to
LITE. After burner lights push in and turn
knob to desired setting. Use CAUTION
when lighting surface burners manually.
Setting Surface Controls
Your range may be equipped with different sized surface burners. The ability to
heat food quicker and in larger volumes increases as the burner size increases.
The simmer burner (if equipped) is best used for simmering delicate sauces,
etc. The standard burners can be used for most surface cooking needs. The
Power Plus™ burners (if equipped) are best used for bringing large quantities
of liquid to temperature and when preparing larger quantities of food.
Regardless of size, always select cookware that is suitable for the amount and
type of food being prepared. Select a burner and flame size appropriate to the
pan. Never allow flames to extend beyond the outer edge of the pan.
Each burner lights automatically from an electric ignitor each time a control
knob is turned to the LITE position.
Operating the Surface Burners
1. Place cooking utensil on surface burner.
2. Push the surface control knob in and turn counterclockwise out of the
OFF position.
3. Release the knob and rotate to the LITE position. Note: All four electronic
surface ignitors will spark at the same time. However, only the burner you
are turning on will ignite.
3. Visually check that the burner has lit.
4. Push the control knob in and turn counterclockwise to the desired flame
size. The control knobs do not have to be set at a particular setting. Use
the guides and adjust the flame as needed. DO NOT cook with the surface
control knob in the LITE position. (The electronic ignitor will continue to
spark if the knob is left in the LITE position.)
Setting Proper Surface Burner Flame Size
Proper
Flame
Size
Improper
Flame
Size
Never extend the flame beyond the outer
edge of the utensil. A higher flame
simply wastes heat and energy, and
increases your risk of being being burned
by the flame.
For most cooking: Start on the highest control setting and then turn to a
lower one to complete the process. Use the recommendations below as a
guide for determining proper flame size for various types of cooking. The size
and type of utensil used and the amount of food being cooked will influence the
setting needed for cooking.
For deep fat frying: Use a thermometer & adjust the surface control knob
accordingly. If the fat is too cool, the food will absorb the fat and be greasy. If
the fat is too hot, the food will brown so quickly that the center will be
undercooked. Do not attempt to deep fat fry too much food at once as the food
will neither brown nor cook properly.
*Flame Size
High Flame
Medium Flame
Low Flame
Type of Cooking
Start most foods; bring water to a boil; pan broiling.
Maintain a slow boil; thicken sauces, gravies; steaming.
Keep foods cooking; poach; stewing.
*These settings are based on using medium-weight metal or aluminum
cookware with lids. Settings may vary when using other types of
cookware. The color of the flame is the key to proper burner adjustment. A
good flame is clear, blue & nearly invisible in a well-lighted room. Each cone of
flame should be steady & sharp. Adjust or clean burner if flame is yelloworange.
5
Before Setting Oven Controls
Oven Vent Location
The oven vent is located below the backguard. When the oven is on, warm air is
released through this vent. This venting is necessary for proper air circulation in the oven
and good baking results. DO NOT BLOCK THE OVEN VENT.
Arranging Oven Racks
ALWAYS ARRANGE OVEN RACKS WHEN THE OVEN IS COOL (PRIOR TO
OPERATING THE OVEN). Always use oven mitts when using the oven.
Removing & Replacing Oven Racks
To remove, pull the rack forward until it stops. Lift up front of rack and slide out. To replace, fit the rack onto the guides
on the oven walls. Tilt the front of the rack upward and slide the rack back into place.
Arranging Oven Racks with 6 Rack Positions
To bake on a single rack, place the rack on position 2 or 3. To bake on 2 racks,
place the racks on positions 1 & 3.
Recomended Rack Positions for Broiling, Baking & Roasting:
Rack Position
Food
4 or 5
Broiling meats, chicken or fish.
2 or 3
Cookies, cakes, pies, biscuits & muffins.
1
Frozen pies, angel food cake, yeast, bread, casseroles, small
cuts of meat or poultry.
1 or Roasting Shelf
Turkey, roast or ham.
Oven Control Functions
Note: The time of day must first be set in order to operate the oven.
READ THE INSTRUCTIONS CAREFULLY BEFORE USING THE OVEN. For satisfactory use of your oven, become familiar with
the various functions of the oven as described below.
UP & DOWN ARROW PADS— Used
along with the function pads to
select oven temperature, time of
day, clean time & minute timer.
BAKE PAD—Used to
select the bake
function.
BROIL PAD—
Used to select
the variable
broil function.
TIMER ON/OFF PAD— Used to set or cancel the
minute timer. The minute timer does not start or
stop cooking.
CLOCK SET PAD— Used
to set the time of day.
6
CLEAR/OFF — Used to clear any function previously
entered except the time of day and minute timer. Press
CLEAR/OFF to stop cooking.
Oven Control Functions
Note: The time of day must first be set in order to operate the oven.
To Set the Clock
When the range is first plugged in, or when the power supply to the range has been interrupted, the display will flash "12:00".
1. Press
.
2. Within 5 seconds, press and hold the
or
until the correct time of day appears in the display.
To Set the Minute Timer:
1. Press
2. Press the
.
to increase the time in one minute increments. Press and hold the
to increase the time in 10
minute increments. The timer can be set for any amount of time from 1 minute to 11 hours and 59 minutes.
Note: If you press the
first, the timer will advance to 11 hours and 59 minutes.
3. The display shows the timer count down in minutes until one minute remains. Then the display will count down in
seconds.
4. When the set time has run out, the timer will sound a 3 second beep. 0:00 will appear in the display until
is
pressed.
Note: While the minute timer is counting down, the “:” will flash. The minute timer does not start or stop cooking. It serves
as an extra timer in the kitchen that will beep when the set time has run out. The minute timer can be used alone or during
any of the other oven functions. When the minute timer is in use with any other function, the minute timer will be shown in
the display. To view other functions, press the pad for that function.
To Change the Minute Timer while it is in use:
While the timer is active and shows in the display, press and hold the
To Cancel the Minute Timer before the set time has run out: Press
or
to increase or decrease the time.
.
Changing the Temperature Display Mode (some models)
The electronic oven control temperature display mode was factory preset to display (Fahrenheit) °F oven tempertaures.
Note: Oven cooking temperatures may be set from 170°F to 550°F (77°C to 287°C).
To change the Temperature Display Mode to °C (Celsius) or from °C to °F (do not use Bake or Broil while changing
the Temperature Display Mode):
1. Press & hold the
key pad for 6-8 seconds until F or C appears in the display. Note: At this time the display will
show the current Temperature Display Mode whether set for F or C .
2. Press the
key pad once to choose the (Fahrenheit) °F mode; or press the
key pad once to choose the
(Celsius) °C mode.
3. After 5 seconds, the display will flash. To accept the change, wait 5 more seconds until the oven control beeps once.
To complete the change skip step 4 below, OR;
F or C ) you decide the change is not
4. If at any time during the process of changing the Temperature Display Mode (F
desired, press the
key pad before the oven control beeps once to cancel the process.
5. The control will beep once. The display will then return to the time of day with any temperature display mode change
you may have requested.
7
Setting Oven Controls
Note: The time of day must first be set in order to operate the oven.
To Set or Change the Temperature for Baking
The oven can be programmed to bake at any temperature from 170°F to 500°F.
To Set the Controls for Baking:
1. Press
. "— — —°" appears in the display.
2. Within 5 seconds, press the
or
. The display will show "350°F." By pressing and holding the
or
the temperature can then be adjusted in 5°F increments.
3. When the
or
is released, the oven will begin heating to the selected temperature. When the displayed
temperature reaches the desired baking temperature, the control will beep once.
4. To cancel the baking function, press
.
To Change the Oven Temperature after Baking has Started:
1. Press
2. Press the
and make sure the bake temperature is displayed.
or
to increase or decrease the set temperature.
8
,
Setting Oven Controls
Note: The time of day must first be set in order to operate the oven.
To Broil
1.
2.
3.
4.
Slide broiler drawer out to the stop position.
Remove broiler pan & insert (See Fig. 1).
Position rack before setting control; while range is cool.
Position rack by tilting front of rack up & pulling rack out
from locating holes in rear of broiler drawer. Reposition
back of rack in the desired locating holes & allow front
of rack to slide down into the corresponding slots in
front of broiler drawer (See Fig. 2). NOTE: For mediumrare meats, position the rack closer to the burner (upper
position). For medium foods use middle position. For
well-done foods such as chicken, lobster tails or thick
cuts of meat, position the rack further from the burner
(lower position).
Fig. 2
5. Place insert on broiler pan, then place meat on insert.
DO NOT use the broiler pan without the insert. DO
NOT cover the insert with aluminum foil. The exposed
fat could ignite.
6. Place broiler pan on rack; make sure the broiler pan
with the insert is positioned as shown (See Fig.1). Be
sure front of pan is positioned correctly in rack.
7. Slide the broiler drawer all the way into the range. Press
Fig. 1
Fig. 3
NOTE: The broiler pan & insert allows grease to drain and be kept
away from the high heat of the broiler (See Fig. 3). DO NOT use the
pan without the insert. DO NOT cover the insert with foil; the
exposed grease could ignite.
on Oven Control.
8. Press and hold the
broil or the
or
until the desired broil setting level appears in the display. Press the
for HI (high)
for LO (low) broil. Most foods can be broiled at the HI broil setting. Select the LO broil setting to avoid
excess browning or drying of foods that should be broiled to the well-done stage.
9. Broil on one side until food is browned; turn and cook on the second side. Note: Always pull the rack out to the stop
position before turning or removing food.
10. When broiling is finished, press
.
11. When removing broiler pan from broiler drawer always use pot holders.
DO NOT use the broiler drawer for storage. Items placed in the broiler drawer will catch fire.
Should an oven fire occur, close the oven door and turn off the oven. If the fire continues, use a fire
extinguisher. DO NOT put water or flour on the fire. Flour may be explosive.
9
Adjusting Your Oven Temperature
(some models)
Your new oven has been factory calibrated and tested to ensure an accurate baking temperature. For the first few uses, follow
your recipe times and temperature recommendations carefully. If you feel your oven is too hot or too cool from your baking
experience, the oven temperature may be adjusted to your liking.
Note: DO NOT adjust your oven temperature based on oven thermometers, such as those found in grocery stores, they may
not be accurate.
To Adjust the Oven Temperature (do not use Bake or Broil while adjusting the oven temperature):
1. Press & hold the
key pad and release after the display begins flashing the factory temperature setting of 00.
Note: If the oven temperature has been previously adjusted from the factory setting, the current temperature adjusted value
will flash in the display instead.
2. You may increase the oven temperature in 5°F increments with each press of the
key pad to a maximum oven adjustment
of +35°F. You may also adjust the oven temperature downward in 5°F increments with each press of the
key pad ( total
adjustment range of -35 to +35 F. Note: Your oven control was factory set in the (Fahrenheit) °F Temperature Display Mode.
To change for (Celsius) °C, see Changing the Temperature Display Mode in the Oven Control Functions section of this
Use & Care Manual.
3. If no other key pad is pressed after 5 seconds the display will begin to flash.
4. If you do not want to keep the display adjustment, press the
key pad before the oven control beeps. This will cancel
the temperature adjustment procedure. To start this procedure over again begin with step 1 above OR;
5. If you want to keep the adjustment, wait until the display quits flashing and the oven control beeps once.
6. The oven temperature adjustment has be accepted by the oven control and the display will return to the time of day.
Notes: The oven temperature adjustment may be made if your oven control has been set to operate in the (Celsius) °C
Temperature Display Mode. In this case each press of the
or
key will adjust in 1°C increments upward (maximum
+18°C) or downward (maximum -18°C), depending on which arrow key pad is pressed.
10
General Care & Cleaning
(Cleaning Chart)
Surfaces
How to Clean
Aluminum (Trim
Pieces) & Vinyl
Glass, Painted
Plastic Body Parts &
Control Knobs
Use hot, soapy water and a cloth. Dry with a clean cloth.
Painted Control
Panels
Before cleaning the control panel, turn all controls to OFF and remove the control knobs. To
remove, pull each knob straight off the shaft. Clean as instructed above. Squeeze excess water
from the cloth before wiping the panel; especially when wiping around the controls. Excess water
in or around the controls may cause damage to the appliance. To replace knobs after cleaning,
line up the flat sides of both the knob and the shaft, then push the knob(s) into place.
Porcelain Enamel,
Broiler Pan & Insert
(some models),
Broiler Drawer, Door
Liner & Oven Bottom
Gentle scouring with a soapy scouring pad will remove most spots. Rinse with a 1:1 solution of
clean water and ammonia. If necessary, cover difficult spots with an ammonia-soaked paper
towel for 30 to 40 minutes. Rinse with clean water and a damp cloth, then scrub with a soapfilled scouring pad. Rinse and wipe dry with a clean cloth. Remove all cleaners or the porcelain
may become damaged during future heating. DO NOT use spray oven cleaners on the range top.
Oven Racks
Remove racks. See "Removing & Replacing Oven Racks" under Before Setting Oven Controls.
Use a mild, abrasive cleaner, following the cleaner’s recommendations. Rinse with clean water &
let dry. After cleaning the racks, rub the sides of the racks with wax paper or a cloth containing a
small amount of salad oil (this will make the racks glide easier into the oven rack positions).
Oven Door
Use soap & water to thoroughly clean the top, sides & front of the oven door. Rinse well. You
may use a glass cleaner on the outside glass of the oven door. DO NOT immerse the door in
water. DO NOT spray or allow water or the glass cleaner to enter the door vents. DO NOT
use oven cleaners, cleaning powders or any harsh abrasive cleaning materials on the outside of
the oven door. DO NOT clean the oven door gasket. The oven door gasket is made of a woven
material, on Self-Cleaning models, which is essential for a good seal. Care should be taken not
to rub, damage or remove this gasket.
For cooktop, burners
caps, burner heads
and grates
See "Cleaning the Cooktop" later in this section
Stainless Steel (some
models)
Clean stainless steel with a dishcloth using hot, soapy water. Rinse with clean water & a cloth.
Do not use cleaners with high concentrations of chlorides or chlorines. Do not use harsh
scrubbing cleaners. Only use kitchen cleaners that are especially made for cleaning stainless
steel. Always be sure to rinse the cleaners from the surface as bluish stains may occur during
heating that cannot be removed.
For general cleaning, use hot, soapy water and a cloth. For more difficult soils and built-up
grease, apply a liquid detergent directly onto the soil. Leave on soil for 30 to 60 minutes. Rinse
with a damp cloth and dry. DO NOT use abrasive cleaners on any of these materials; they can
scratch.
11
General Care & Cleaning
Cleaning the Cooktop
The cooktop is designed to make cleaning easier. Since the four burners are sealed, cleanups are easy when spillovers
are cleaned up immediately. To clean, wipe with a clean, damp cloth and wipe dry. DO NOT attempt to clean the cooktop
when the cooktop or burner heads are still hot. The contoured well areas and burner drip pans (some models) should be
routinely cleaned. Keeping the burner head ports and slots clean will prevent improper ignition and an uneven flame. Refer
to the following sections for further instructions.
DO NOT attempt to clean the cooktop when
the cooktop or burner heads are still hot. Touching hot
cooktop areas, burner grates and burner caps can cause
burns.
Any additions, changes or conversions
required in order for this appliance to satisfactorily meet the
application needs must be made by an authorized
Electrolux Distributor or Qualified Agency.
To clean the burner head ignition ports - Each burner head has a small
ignition port located as illustrated. Should you experience ignition problems it
may be that this port hole is partially blocked with soil. With the burner head in
place, use a small wire gauge needle or the end of a paper clip to clear the
ignition port.
To Clean the Surface Burner Heads - For proper gas flow it may be necessary
to clean the burner head and slots. To clean, first use a clean DAMP cloth to
soak up any spills. Remove any food from between the burner slots using a small
non-abrasive brush like a toothbrush and afterwards wipe up using a damp cloth.
For stubborn soils located in the slots, use a small-gauge wire or needle to clean
the slots.
slots
ignition port
orifice port
Cooktop Burner Head
Please Note: The surface burner heads are secured to the cooktop and must be
cleaned in place on the cooktop.
For proper flow of gas and ignition of the burner — DO NOT ALLOW SPILLS, FOOD, CLEANING AGENTS OR ANY
OTHER MATERIAL TO ENTER THE GAS ORIFICE HOLDER OPENING. ALWAYS keep the surface burner cap and
surface burner head in place whenever a surface burner is in use.
To Clean the Recessed and Contoured Well Areas of the Cooktop - If a spill occurs on or in the recessed or contoured
areas, blot up spill with an absorbent cloth. Rinse with a clean, damp cloth and wipe dry.
To Clean the Surface Burner Grates, Caps & Surface Burner Drip Pans (some models) - Use a soap-filled scouring
pad or a mild abrasive cleanser to clean the surface burner caps and surface burner drip pans (if equipped).
Please Note: THE COOKTOP IS NOT REMOVABLE. Do not attempt to remove or lift the cooktop.
12
General Care & Cleaning
Removing & Replacing the Oven Door (all models)
The door is heavy. For safe, temporary storage, lay the door flat
with the inside of the door facing down.
Fig. 1
Fig. 2
Fig. 3
To Remove Oven Door:
1. Open oven door completely (horizontal with floor - See Fig. 1).
2. Remove 2 screws located on the inside of the oven door liner (See A Fig. 2).
3. Insert the 2 screws into the door hinge holes located on the side of the hinge
arm, one into each hinge (See B Fig. 2).
4. Close oven door until the door stops, (Do not force the door to close any
further). The placement of these screws should keep door open in about a 45
degree position.
5. Grasp oven door firmly on both sides and slide door up and off hinges at the
same angle. (See Fig. 3)
6. To clean oven door, follow the instructions provided in the Cleaning Chart at
the beginning of the Care & Cleaning section (See Door Liner).
To Replace Oven Door:
1. Be sure the hinge arms remain at the 45 degree angle position. Be sure the
screws are still locking the hinge arms from moving. If the screws fall out of
the hinge holes, the hinge(s) may snap back against the oven frame and could
pinch fingers or chip the porcelain finish on the oven front frame.
2. Hold door at the sides near the top while resting the lower front of door on your
knee. Insert the door channels at the bottom of door over the door hinges,
(See Fig. 3).
3. Allow the door to slide down into the door hinges evenly at the same 45
degree angle. The hinge arms should be inserted into the bottom corners as
far as they can go.
4. Open door completely (horizontal with floor) and remove both screws from
holes in door hinges.
5. Reinstall the 2 screws into the door liner (See C Fig. 2).
6. If the door is not in alignment with the oven frame, remove door and repeat the
above steps.
Changing the Oven Light (some models)
On some models, the oven light automatically turns on when the door is opened.
Some models have a switch located on the control panel to turn on the light. The
oven light is located at the rear of the oven.
To
1.
2.
3.
4.
replace the oven light:
Turn electrical power off at the main source or unplug the range.
Replace bulb with a new 40 watt appliance bulb.
Turn power back on again at the main source (or plug the range back in).
The clock will then need to be reset. To reset, see “Setting the Clock” and
“Setting the Minute Timer” under Setting Oven Controls in this Use & Care
Manual.
Be sure the range is unplugged and all parts are COOL before
replacing oven light. Wear a leather-faced glove for protection against possible
broken glass.
13
Before You Call
Solutions to Common Problems
Before you call for service, review the following list. It may save you time & expense. The list includes common occurrences
(shown in bold) that are not the result of defective workmanship or materials in this appliance. The possible corrections to these
problems are provided with the problem listed:
Range is not level - (1) Poor installation. Place oven rack in
center of oven. Place a level on the oven rack. Adjust leveling
legs at base of range until the oven rack is level. (2) Be sure
floor is level, strong & stable enough to adequately support
range. (3) If floor is sagging or sloping, contact a carpenter to
correct the situation. (4) Kitchen cabinet alignment may make
range appear not level. Be sure cabinets are square & have
sufficient room for range clearance.
Poor baking results - Many factors affect baking results. Make
sure the proper oven rack position is used. Center food in the
oven & space pans to allow air to circulate. Allow the oven to
preheat to the set temperature before placing food in the oven.
Try adjusting the recipe's recommended temperature or baking
time.
Oven light does not work (some models) - Replace or tighten bulb.
See Changing Oven Light section in this Use & Care Manual.
Cannot move appliance easily. Appliance must be accessible
for service - (1) Cabinets not square or are built in too tightly.
Contact builder or installer to make appliance accessible. (2)
Carpet interferes with range. Provide sufficient space so range
can be lifted over carpet.
Surface Burners do not light - (1) Surface Control knob was
not completely turned to LITE. Push in & turn the Surface
Control knob to LITE until burner ignites and then turn control
knob to desired flame size. (2) Burner ports are clogged. With
the burner OFF, use a small-gauge wire or needle to clean
ports. See “Cleaning the Contoured Well Areas, Burner Caps,
Head & Drip Pans” in the General Care & Cleaning section for
additional cleaning instructions. (3) Range power cord is
disconnected from outlet (electric ignition models only). Be
sure power cord is securely plugged into the outlet. (4)
Electrical power outage (electric ignition models only). Burners
can be lit manually. See section on Setting Surface Controls.
Oven smokes excessively during broiling - (1) Control(s) not
set properly. Follow Broil instructions under Setting Oven
Controls. (2) Broiler Drawer is open. The Broiler Drawer should
be closed while broiling. (3) Meat too close to the broil element.
Reposition the broil rack to provide proper clearance between
the meat & the element. Preheat the broil element for searing.
(4) Meat not properly prepared. Remove excess fat from meat.
Cut remaining fatty edges to prevent curling, but do not cut into
lean. (5) Insert on broiler pan wrong side up & grease not
draining. Always place grid on the broiler pan with ribs up &
slots down to allow grease to drip into pan (some models). (6)
Grease has built up on oven surfaces. Regular cleaning is
necessary when broiling frequently. Old grease or food spatters
cause excessive smoking.
Flames inside oven or smoking from oven vent - Excessive
spillovers in oven. This will especially be the case for pie
spillovers or large amounts of grease on the oven bottom. Wipe
up excessive spillovers before starting oven. If flames or
excessive smoke are present see “To Broil” in the Setting Oven
Controls section.
Surface burner flame burns only part way around burner cap
- (1) Burner ports are clogged. With the gas burner OFF, clean
ports with a small-gauge wire or needle. (2) Moisture is
present after cleaning. Lightly fan the flame & allow burner to
operate until flame is full. Dry the burners thoroughly following
the instructions under “Cleaning the Contoured Well Areas,
Burner Caps, Head & Drip Pans” in the General Care &
Cleaning section.
Oven control beeps & displays any F code error (for example
F11; some models) - Electronic control has detected a fault
condition. Press CLEAR/OFF to clear the display & stop
beeping. Try the Bake or Broil function again. If the F code error
repeats, remove power suppy to appliance, wait 5 minutes and
then repower the appliance and set clock time of day. Try the
Bake or Broil function again. If the fault recurs, record fault
number, press CLEAR/OFF & contact an authorized service
agent.
Surface burner flame is orange - (1) Dust particles in gas main
line. Allow the gas burner to operate a few minutes until flame turns
blue in color. (2) In coastal areas a slightly orange flame may be
unavoidable due to salt in air.
Oven does not operate - (1) Be sure the oven controls are set
properly for the desired function. See Setting Oven Controls in
this Use & Care Manual or read the instructions for “Entire
appliance does not operate” listed below. (2) Be sure the Gas
Regulator Valve is in the “ON” position. Refer to the Installation
Instructions to for more information.
Oven control beeps and displays any “F” code error (for
example F3; some models) - Electronic control has detected a
fault condition. Press CLEAR/OFF to clear the display & stop
beeping. Reprogram oven. If fault recurs, record fault number.
Press CLEAR/OFF & contact your authorized service agent.
Poor baking results - Many factors affect baking results. Make
sure the proper oven rack position is used. Center food in the
oven & space pans to allow air to circulate. Allow the oven to
preheat to the set temperature before placing food in the oven.
Try adjusting the recipe's recommended temperature or baking
time. If you feel the oven is too hot or cool, see Adjusting Your
Oven Temperature in this Use & Care Manual (some models).
Entire appliance does not operate - (1) The time of day is not
set. The time of day must first be set in order to operate the
oven. See “To Set the Clock” in the Setting Oven Controls
section.(2) Make sure cord/plug is plugged correctly into outlet.
(3) Service wiring is not complete. Contact your dealer,
installing agent or authorized service agent. (4) Electrical
power outage (electric ignition models only). Check house
lights to be sure. Call your local electric company for service.
Surface gas burners can be lit manually. See Setting Surface
Controls in this Use & Care Manual.
14
Notes
15
Major Appliance Warranty Information
Your appliance is covered by a one year limited warranty. For one year from your original date of
purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be
defective in materials or workmanship when such appliance is installed, used and maintained in
accordance with the provided instructions.
Exclusions
This warranty does not cover the following:
1.
Products with original serial numbers that have been removed, altered or cannot be readily determined.
2.
Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.
3.
Rust on the interior or exterior of the unit.
4.
Products purchased "as-is" are not covered by this warranty.
5.
Food loss due to any refrigerator or freezer failures.
6.
Products used in a commercial setting.
7.
Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances
not in ordinary household use or used other than in accordance with the provided instructions.
8.
Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9.
Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards,
shelves, etc.,which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or
knobs, handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not limited to
floors, cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or
external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT
REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES,
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR.
ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS
PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN
LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE
DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO
YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER
RIGHTS THAT VARY FROM STATE TO STATE.
If You Need
Service
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone
numbers below.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada
Corp. Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and
parts under this warranty must be performed by Electrolux or an authorized service company. Product features or
specifications as described or illustrated are subject to change without notice.
USA
1.800.944.9044
Electrolux Major Appliances
North America
P.O. Box 212378
Augusta, GA 30907
Canada
1.800.668.4606
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4
Download PDF

advertising