Owner`s manual | Franke Consumer Products FPL 606 Cooktop User Manual

R
CLASSIC BAY 1200 PELLET STOVE
Owner’s Manual
Installation and Operation
Model:
CB1200
Beaverton
Oregon USA
Tested and
Listed by
US
C
OMNI- Test Laboratories, Inc.
CAUTION
DO NOT DISCARD THIS MANUAL
• Important operating and • Read, understand and • Leave this manual with
party responsible for use
follow these instructions
maintenance instrucand operation.
for safe installation and
tions included.
operation.
WARNING
OT
DO N ARD
C
DIS
WARNING
Please read this entire manual
before installation and use of this
pellet fuel-burning room heater.
Failure to follow these instructions
could result in property damage,
bodily injury or even death.
• Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
• Do not overfire - If any external part starts to
glow, you are overfiring. Reduce feed rate.
Overfiring will void your warranty.
HOT! DO NOT TOUCH.
SEVERE BURNS MAY RESULT.
CLOTHING IGNITION MAY RESULT.
Glass and other surfaces are hot
during operation and cool down.
• Keep children away.
• CAREFULLY SUPERVISE children in same room
as appliance.
• Alert children and adults to hazards of high
temperatures.
• Do NOT operate with protective barriers open or
removed.
• Comply with all minimum clearances to combustibles as specified. Failure to comply may
cause house fire.
• Keep clothing, furniture, draperies and other
combustibles away.
CAUTION
Check building codes prior to installation.
• Installation MUST comply with local, regional, state
and national codes and regulations.
• Consult local building, fire officials or authorities
having jurisdiction about restrictions, installation
inspection, and permits.
CAUTION
Tested and approved for wood pellets and shelled
field corn fuel only. Burning of any other type of fuel
voids your warranty.
www.quadrafire.com
7014-082B
September 21, 2006
CB 1200 Pellet Stove
R
and Welcome to the Quadra-Fire Family!
Hearth & Home Technologies welcomes you to our tradition of excellence! In choosing a Quadra-Fire appliance,
you have our assurance of commitment to quality, durability, and performance.
meticulously fabricated and gold and nickel surfaces are
hand-finished for lasting beauty and enjoyment. Our pledge
to quality is completed as each model undergoes a quality
control inspection. From design, to fabrication, to shipping:
Our guarantee of quality is more than a word, it’s QuadraFire tradition, and we proudly back this tradition with a Limited Lifetime Warranty.
This commitment begins with our research of the market,
including ‘Voice of the Customer’ contacts, ensuring we
make products that will satisfy your needs. Our Research
We wish you and your family many years of enjoyment in the
and Development facility then employs the world’s most
warmth and comfort of your hearth appliance. Thank you for
advanced technology to achieve the optimum operation of
choosing Quadra-Fire.
our stoves, inserts and fireplaces. And yet we are oldfashioned when it comes to craftsmanship. Each unit is
With warm regards,
___________________________
___________________________
Dan Henry
Vice President
Advanced Technolgies
Alan Trusler
t
Senior
Vice President
Dealer Channel
_________________________
Jason Olmstead
Vice President &
General Manager
___________________________
Steve Tate
Quadra-Fire
Brand Manager
SAMPLE SERIAL NUMBER / SAFETY LABEL LOCATION:
Behind left side curtain on outside of hopper wall.
CAUTION: HOT WHILE IN OPERATION DO NOT TOUCH. KEEP CHILDREN, CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE
SKIN BURNS. SEE NAMEPLATE AND INSTRUCTIONS. Operate this unit with fuel hopper lid closed. Failure to do so may result in emissions
products' combustion from the hopper under certain conditions. Maintain hopper seal in good condition. Do no over fill the hopper.
CHAUD LORS DE L'OPÉRATION. NE PAS TOUCHER. GARDEZ LES ENFANTS ET LES VÊTEMENTS LOIN DE L'ESPACE DÉSIGNÉ DE L'INSTALLATION. LE
CONTACT PEUT CAUSER DES BRÛLURES À LA PEAU. VOIR L'ÉTIQUETTE ET LES INSTRUCTIONS. Opérez cet appareil avec le couvercle de la trémie fermé. Le défaut de ne
pas suivre les instructions peut résulter, sous certaines conditions, en une combustion des émissions des produits venant de la trémie. Ne pas remplir la trémie trop pleine.
ATTENTION:
O-T L
Listed by
Report Rapport
061-S-21-4
Beaverton
Oregon USA
C
OMNI-Test Laboratories, Inc.
Testing Lab &
Report Number
SERIAL NO. NUMÉRO DU
CB 1200 Pellet Stove 007C
R
Appareil de chauffage inséré de combustible solide/de type de boulettes. Accepté dans l'installation dans les maisons mobiles. Cet
appareil a été testé et enregistré pour l'usage dans les Maisons Mobiles en accord avec OAR 814-23-9000 jusqu'à 814-23-909.
Testé à: ASTM #1509-95, ORD-C 1482-M1990 Room Heating. Pellet Burning Type, APFI, (UM) 84-HUD POUR
USAGE AVEC LES BOULETTES DE BOIS OU DE COMBUSTIBLE DE MAIS ÉCOSSÉ DES CHAMPS.
Puissance de Rendement: 40,000 Btu's/hr
Puissance Électrique: 115 VAC, 60 Hz, Début 4.6 Amps, Courir 1.6 Amps,
Éloignez le fil électrique de l'appareil. Ne pas faire passer le fil électrique au dessus ou en dessous de l'appareil.
DANGER: Il y a risque de décharge électrique. Déconnectez le fil électrique de la prise de contact avant le service.
Remplacez la vitre seulement avec une vitre céramique de 5 mm disponible chez votre fournisseur.
Pour allumer, monter la température du thermostat au dessus de la température de la pièce, le poêle s'allumera
automatiquement. Pour éteindre, descendre la température du thermostat en dessous de la température de la pièce. Pour des
instructions supplémentaires, référez vous au manuel du propriétaire. Gardez la porte d'ouverture et la porte des cendres
fermées hermétiquement durant l'opération.
Serial Number
Model
E
Listed Solid Fuel Room Heater/Pellet Type Insert. Also suitable for Mobile Home Installation. This appliance has
been tested and listed for use in Manufactured Homes in accordance with OAR 814-23-9000 through 814-23-909.
Tested to: ASTM E1509, ORD-C-1482-M1990 Room Heating Pellet Burning Type, APFI, (UM) 84-HUD FOR
USE ONLY WITH PELLETIZED WOOD OR SHELLED FIELD CORN FUEL.
Input Rating: 40,000 Btu's/hr
Electrical Rating: 115 VAC, 60 Hz, Start 4.6 Amps, Run 1.6 AMPS.
Route power cord away from unit. Do not route cord under or in front of appliance.
DANGER: Risk of electrical shock. Disconnect power supply before servicing. Replace glass only with 5mm
ceramic available from your dealer. To start, set thermostat above room temperature, the stove will light
automatically. To shutdown, set thermostat to below room temperature. For further instruction refer to owner's
manual.Keep viewing and ash removal doors tightly closed during operation.
C
B
E
D
B
C
PL
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS / ESPACES LIBRES MINIMUM DES MATÉRIAUX COMBUSTIBLES:
A
C
A
C
B
E
M
Note 1: In residential installations, when using Parts 811-0580, (3" - 3" Top Vent Adapter) and
812-2690 (3" - 6" Top Vent Adapter Collar) 24 gauge 6" single wall flue connector may be used.
F
Note 1: Dans les installations résidentielles, lorsque les pièces 811-0580, (dessus de l'adapteur de
ventilation 3" - 3") et 812-2690 (collier de l'adapteur de ventilation 3" - 6"), un tuyau connecteur de 6"
pour mur simple de calibre 24 peut être utilisé.
D
SA
A
Note 2: In manufactured home installation, when using Part 811-0580, (3" - 3" Top Vent Adapter) and
812-2690 (3' - 6" Top Vent Adapter Collar), use listed double wall flue connector. An Outside Air Kit
(Part 811-0560 rear or 811-0570 floor), must be used with manufactured home installation.
Note 2: Pour l'installation dans les maisons préfabriquées, lorsque les pièces 811-0580 (dessus de
l'adapteur de ventilation 3" - 3") et 812-2690 (collier de l'adapteur de ventilation 3" - 6"), utilisez un
tuyau connecteur enregistré pour mur double. Un assemblage d'air extérieur (pièce 811-0560 arrière
au 811-0570 la plancer), doit être utilisé pour l'installation dans les maisons préfabriquées.
G
I
G = 2"/51mm
H* = 2"/51mm
I = 6"/152mm
*Non-combustible floor protection must extend beneath the flue pipe when installed with
horizontal venting or under the Top Vent Adapter with vertical installation.
RECOMMENDED IN USA; REQUIRED IN CANADA
Floor protector must be noncombustible material, extending beneath heater and to the
front/sides/rear as indicated. Measure front distance (I) from the surface of the glass door.
2"/51mm
3"/76mm
6"/152mm
2"/51mm
36"/914mm
2"/51mm
6"/152mm
2" (51mm)
12.5"/318mm
3"/76mm
*Un protecteur incombustible de plancher doit s'étendre sous le conduit de cheminée pour une
installation de ventilation horizontale ou sous un adapteur de ventilation de dessus pour une
installation verticale. ÉTATS-UNIS - RECOMMANDÉ; CANADA - REQUIRENT
Le poêle doit être placé sur une assise non combustible s’étendant tout autour de lui, comme les
schémas l’indiquent. Mesurez la distance du devant (I) de la surface de la porte vitrée.
U.S. ENVIRONMENTAL PROTECTION AGENCY This model is exempt from EPA certification under 40 CFR 60.531 by definition [Wood Heater (A) "Air-to-Fuel Ratio"].
1445 Highway North
Colville, WA 99114
www.quadrafire.com
Page 2"/51mm
6"/152mm
FLOOR PROTECTION / PROTECTION DU SOL
H*
G
A
Back Wall to stove / Mur Arrière du poêle
B
Side Wall to Cast Top / Mur De Côté du haut
CORNER INSTALLATION / NSTALLATION DU COIN :
C
Side Wall / Mur De Côté
VERTICAL ADAPTER KIT INSTALLATION:
UN ASSEMBLAGE POUR ADAPTEUR POUR INSTALLATION VERTICALE:
D
Back Wall to Flue Pipe / Mur Arrière tuyau rigide
B
Side Wall to Cast Top / Mur De Côté du haut
CORNER INSTALLATION WITH VERTICAL ADAPTER KIT:
INSTALLATION DU COIN AVEC UN ASSEMBLAGE D'ADAPTEUR VERTICAL:
E
Side Wall / Mur De Côté
ALCOVE INSTALLATION / INSTALLATION DE L' ALCÔVE:
Max. Alcove Depth: / La profondeur maximum de l'alcôve
A
Back Wall to stove / Mur Arrière du poêle
B
Side Wall to Cast Top / Mur De Côté du haut
C
Unit corner to diagonal wall /
F
Top of Unit to Combustibles / Du poêle du haut combustibles
Alcove vertical installation / Installation verticale de l'alcôve
D
Back Wall to Flue Pipe / Mur Arrière tuyau rigide
2006
2007
2008
JAN
FEB
MAR
DO NOT REMOVE THIS LABEL / NE PAS ENLEVER L'ÉTIQUETTE
APR
MAY
JUNE JULY AUG
Made in China/Fait Aux Chine
7014-082B
SEPT OCT
NOV DEC
250-3182
Mfg Date
September 21, 2006
R
CB 1200 Pellet Stove
R
TABLE OF CONTENTS
Section 1: Listing and Code Approvals
A.
B.
C.
D.
E.
Appliance Certifications.......................4
Mobile Home Approved.......................4
Glass Specifications.............................4
Electrical Rating...................................4
BTU & Efficiency Specifications...........4
Section 2: Getting Started
A.
B.
C.
D.
E.
Design, Installation & Location
Considerations.....................................5
Fire Safety...........................................5
Tools & Supplies Needed....................6
Measuring Standards..........................6
Inspect Appliance & Components.......6
Section 3: Dimensions & Clearances
A. Appliance Dimensions.........................7
B. Clearances to Combustibles................8
C. Hearth Requirements..........................9
A.
B.
C.
D.
Chimney & Exhaust Connection..........10
Venting Termination Requirements.....10
Equivalent Feet of Pipe........................11
Pipe Selection Chart.............................11
Starting Your First Fire.........................23
Fire Characteristics..............................23
Feed Rate Adjustment ........................23
Ignition Cycles.....................................24
Frequently Asked Questions...............24
Section 9: Troubleshooting.............................25-27
Section 10: Maintaining & Servicing Appliance
A.
B.
C.
D.
E.
F.
G.
Proper Shutdown Procedures..............28
General Maintenance & Cleaning........28-31
High Ash Fuel Content Maintenance...31
Blower Replacement............................31-32
Igniter Replacement.............................32
Baffle Removal.....................................32
Glass Replacement..............................33
Section 11: Reference Material
Section 4: Vent Information
E.
F. G.
H.
I.
A.
B.
C.
D.
E.
F.
G.
Component Functions & Locations......34-35
Component Locations (Drawings).......36
Exploded Drawings..............................37-39
Service Parts & Accessories...............40-41
Service & Maintenance Log.................42
Warranty Policy....................................43
Contact Information..............................44
Section 5: Venting Systems
A. Alcove..................................................12
B. Through the Wall..................................13
C. Vertical.................................................14
D. Through the Wall & Vertical.................14
E. Masonry...............................................15
F. Alternate Masonry................................15
Section 6: Mobile Home. .................................16
Section 7: Appliance Set-Up
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
Section 8: Operating Instructions
A.
B.
C.
D.
Outside Air Kit, Rear & Floor...............17
Top Vent Adapter . ..............................18
Rear Vent & Rear to Top Vent Adapter..18
Brick Set . ............................................19
Brick Clip .............................................19
Log Set Placement...............................20
Grille Assembly....................................20
Logo Installation...................................20
Door Installation...................................21
Thermostat Installation.........................21
Fuel Size & Material.............................22
General Operation Information............22
Before Your First Fire..........................23
Fuel Adjustment Rod...........................23
September 21, 2006
7014-082B
Page CB 1200 Pellet Stove
1
R
Listing and Code Approvals
A. Appliance Certification
E. BTU & Efficiency Specifications
Model
CB1200 Pellet Stove
Emissions Rating
Laboratory
OMNI Test Laboratories, Inc.
*BTU Output
0. 9 grams/hr
.
14,000 - 40,000 / hr
Report No.
061-S-21-4
Heating Capacity
up to 2,500 sq. ft.
Type
Solid Fuel Room Heater/Pellet Type
Hopper Capacity
80 lbs
Standard
ASTM E1509, ULC S627 and ULC/
ORD-C1482 Room Heater Pellet Fuel
Burning type and (UM) 84-HUD, Mobile
Home Approved.
Fuel
Wood Pellets or Shelled Corn
Shipping Weight
349 lbs
State Listing
Colorado, Listed 09-13-05
*BTU output will vary, depending on the brand of fuel you
use in your stove. Consult your Quadra-Fire dealer for
best results.
B. Mobile Home Approved
This appliance is approved for mobile home installations
when not installed in a sleeping room and when an outside
combustion air inlet is provided. The structural integrity of
the mobile home floor, ceiling, and walls must be maintained.
The appliance must be properly grounded to the frame of
the mobile home and use only listed pellet vent Class “L” or
“PL” connector pipe. A Quadra-Fire Outside Air Kit must be
installed in a mobile home installation.
NOTE: Hearth & Home Technologies, manufacturer of
this appliance, reserves the right to alter its products,
their specifications and/or price without notice.
C. Glass Specifications
This appliance is equipped with 5mm ceramic glass. Replace
glass only with 5mm ceramic glass. Please contact your
dealer for replacement glass.
NOTE: This installation must conform with local codes.
In the absence of local codes you must comply with the
ASTM E1509, (UM) 84-HUD, ULC/ORD-C-1482
D. Electrical Rating
115 VAC, 60 Hz, Start 4.1 Amps, Run 1.1 Amps
Page 7014-082B
September 21, 2006
2
R
CB 1200 Pellet Stove
R
Getting Started
A. Design, Installation & Location
Considerations
B. Fire Safety
1. Appliance Location
Consideration must be given to safety, convenience, traffic
flow, and the fact that the appliance will need a chimney and
chimney connector. It is a good idea to plan your installation
on paper, using exact measurements for clearances and
floor protection, before actually beginning the installation. If
you are not using an existing chimney, place the appliance
where there will be a clear passage for a factory-built listed
chimney through the ceiling and roof.
Check with your local building code agency before you
begin your installation. Be sure local building codes do not
supersede UL specifications and always obtain a building
permit so that insurance protection benefits cannot be
unexpectedly cancelled. If any assistance is required during
installation, please contact your local dealer.
Maintain the designated clearances to combustibles. Insulation must not touch the chimney. You must maintain the
designated air space clearance around the chimney. This
space around a chimney is necessary to allow natural heat
removal from the area. Insulation in this space will cause
a heat buildup, which may ignite wood framing. NOTE:
Clearances may only be reduced by means approved
by the regulatory authority having jurisdiction.
To provide reasonable fire safety, the following should be
given serious consideration:
1. Install at least one smoke detector on each floor of
your home to ensure your safety. They should be
located away from the heating appliance and close
to the sleeping areas. Follow the smoke detector
manufacturer’s placement and installation instructions,
and be sure to maintain regularly.
We recommend that a qualified building inspector and your
insurance company representative review your plans before
and after installation.
2.
A conveniently located Class A fire extinguisher
to contend with small fires resulting from burning
embers.
2. Thermostat Location
3.
A practiced evacuation plan, consisting of at least 2
escape routes.
4.
A plan to deal with a hopper fire as follows:
In the event of a hopper fire:
The thermostat’s location will have some effect on the
appliance’s operation. When the thermostat is located close
to the appliance, it may require a slightly higher temperature
setting to keep the rest of the house comfortable. If the
thermostat location is in an adjacent room or on a different
floor level, you will notice higher temperatures near the
appliance.
a.
b.
c.
d.
e.
CAUTION
• Do NOT connect this unit to a chimney flue servicing
another appliance.
• Do NOT connect to any air distribution duct or system.
f.
Notify fire department
Prepare occupants for immediate evacuation.
Close all openings into the appliance.
Unplug appliance.
While awaiting fire department, watch for ignition
of adjacent combustibles from overheated vent
pipe, hot embers or sparks from the chimney.
Pour a bucket of water into the appliance
hopper.
WARNING
Fire Hazard.
• Do not operate appliance before reading
and understanding operating instructions.
• Failure to operate appliance properly may
cause a house fire.
September 21, 2006
7014-082B
Page CB 1200 Pellet Stove
R
C. Tools And Supplies Needed
E. Inspect Appliance & Components and
Pre-Use Check List
Tools and building supplies normally required
for installation, unless installing into an existing
masonry fireplace:
Reciprocating Saw
Safety Glasses
Channel Locks
Framing Square
Hammer
Electric Drill & Bits (1/4”)
Phillips Screwdriver
1/4” Self-Tapping Screws
Tape Measure
Plumb Line
May also need:
Level
Vent Support Straps
Framing Material
Venting Paint
Hi-temp Caulking Material
Gloves
D. Measuring Standards
1. Pipe measurements are from center line to center line.
2. Vertial terminations are measured to top of pipe.
Measure vertical
clearances from
this surface
1.
Place the appliance in a location near the
final installation area and follow the procedures below:
2.
Open the appliance and remove all the parts
and articles packed inside the Component
Pack. Inspect all the parts and glass for shipping damage. Contact your dealer if any irregularities are noticed.
3.
All safety warnings have been read and followed.
4.
This Owner’s Manual has been read.
5.
Floor protection requirements have been met.
6.
Venting is properly installed.
7.
The proper clearances from the appliance and
chimney to combustible materials have been
met.
8.
The masonry chimney is inspected by a professional and is clean, or the factory built metal
chimney is installed according to the manufacturer’s instructions and clearances.
9.
The chimney meets the required minimum
height.
10.
All labels have been removed from the glass
door.
11.
Plated surfaces have been wiped clean, if
applicable.
12.
Thermostat or remote has been installed.
13.
A power outlet is available nearby.
Measure horizontal
clearances from
this surface
WARNING
Fire Risk.
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be
voided by, the following actions:
Figure 6.1
WARNING
Inspect appliance and components for
damage. Damaged parts may impair safe
operation.
• Do NOT install damaged components.
• Do NOT install incomplete components.
• Do NOT install substitute components.
Report damaged parts to dealer.
Page • Installation and use of any damaged appliance.
• Modification of the appliance.
• Installation other than as instructed by Hearth & Home
Technologies.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
• Operating appliance without fully assembling all
components.
• Operating appliance without legs attached (if supplied
with unit).
• Do NOT Overfire
Or any such action that may cause a fire hazard.
7014-082B
September 21, 2006
R
3
CB 1200 Pellet Stove
R
Dimensions and Clearances
A. Appliance Dimensions
4-5/8 in
(118mm)
8-1/6 in. (205mm) 20- 7/16 in. (519mm)
CL
12-/8 in
(14mm)
5.0 in
(127mm)
14-1/4 in
(62mm)
2-1/2 in
(64mm)
CL
25-/4 in.
(654mm)
27-5/8 in.
(692mm)
28-1/2 in. (724mm)
Figure 7.2 - Top View with Top Vent Adapter
Figure 7.1 - Top View
28-1/2 in.
(724mm)
25-/4 in.
(629mm)
1-5/8 in.
(80mm)
CL
10-/4 in.
(27mm)
8-1/16 in.
(205mm)
24-/4 in.
(629mm)
Figure 7.3 - Side View
September 21, 2006
26-1/2 in.
(67mm)
Figure 7.4 - Front View
7014-082B
Page CB 1200 Pellet Stove
R
B. Clearances to Combustibles (UL and ULC)
C
A
Alcove Installation
Inches
Millimeters
Minimum Alcove Height
44
1117
Minimum Alcove Width
40-1/2
1029
Maximum Alcove Depth
36
915
Minimum Alcove Side Wall
6
152
Top of Unit to Combustibles
12-1/2
318
B
C
WARNING
Straight Back Against
Wall
A Back Wall to Appliance
B Side Wall to Appliance
Inches
Millimeters
2
51
6
152
Corner Installation
C Walls to Appliance
Inches
Millimeters
2
51
Fire Risk.
Comply with all minimum clearances to
combustibles as specified.
Failure to comply may cause house fire.
NOTE:
• Illustrations reflect typical installations and are FOR
DESIGN PURPOSES ONLY.
• Illustrations/diagrams are not drawn to scale.
• Actual installation may vary due to individual design
preference.
Installations with:
3 to 3 inch Top Vent Adapter and
3 to 6 inch Offset Adapter Kit
D
G
F
E
G
Vertical Installation
D Back Wall to Flue Pipe
Side Wall to Top
E
Back Wall to Appliance
F
Inches
Millimeters
3
76
6
152
7.5
191
Corner Installation
G Walls to Appliance
Inches
Millimeters
2
51
Page 7014-082B
September 21, 2006
R
CB 1200 Pellet Stove
R
C. Hearth Pad Requirements (UL and ULC)
Use a non-combustible floor protector, extending beneath
appliance and to the front, sides and rear as indicated.
Measure front distance “M” from the surface of the glass
door.
L*
K
K
M
Figure 9.1
Hearth Pad Requirements
K Sides
L* Back
M Front
Inches
Millimeters
2
51
2
51
6
152
*L Exception for Horizontal Installations:
USA INSTALLATIONS: A non-combustible floor protection is recommended extending beneath the flue pipe
when installed with horizontal venting or under the top
vent adapter with vertical installation.
CANADA INSTALLATIONS: A non-combustible floor
protection extending beneath the flue pipe is required
with horizontal venting or under the top vent adapter with
vertical installation.
Must extend 2 inches (51mm) beyond each
side of pipe (shaded area)
Figure 9.2
September 21, 2006
7014-082B
Page CB 1200 Pellet Stove
4
R
Vent Information
B. Venting Termination Requirements
A. Chimney and Exhaust Connection
1. Chimney & Connector: Use 3 or 4 inch (76-102mm)
diameter type "L" or "PL" venting system. It can be
vented vertically or horizontally.
2. Mobile Home: Approved for all listed pellet vent. If using
the 3 inch (76mm) vertical top vent adapter Kit or the 3
to 6 inch (76-152mm) top vent offset adapter, use listed
double wall flue connector. A Quadra-Fire outside air kit
must be used with manufactured home installations.
3. Residential: The 3 inch (76mm) vertical top vent
adapter kit and the 3 to 6 inch (76-152mm) top vent
offset Adapter are tested to use 24 gauge single wall flue
connector or listed double wall flue connector to Class
A listed metal chimneys, or masonry chimneys meeting
national and/or local codes for solid fuel appliances.
CAUTION
Do not terminate vent in any enclosed or semi-enclosed
area such as a carport, garage, attic, crawl space, under a
sun deck or porch, narrow walkway or closely fenced area,
or any location that can build up a concentration of fumes
such as a stairwell, covered breezeway, etc.
1. Termination must exhaust above air inlet elevation. It is
recommended that at least 60 inches (1524mm) of vertical pipe be installed when appliance is vented directly
through a wall. This will create a natural draft, which
will help prevent the possibility of smoke or odor venting
into the home during a power outage. It will also keep
exhaust from causing a nuisance or hazard by exposing
people or shrubs to high temperatures. The safest and
preferred venting method is to extend the vent vertically
through the roof.
4. Install vent at clearances specified by the
vent manufacturer.
5. Secure exhaust venting system to the appliance with at
least 3 screws. Also secure all connector pipe joints with
at least 3 screws through each joint.
2. Distance from doors and opening windows, or gravity or
ventilation air inlets into building:
a. Not less than 48 inches (1219mm) below;
b. Not less than 48 inches (1219mm) horizontally
from;
c. Not less than 12 inches (305mm) above.
NOTE: All pipe must be welded seam pipe whenever
possible. Seal pipe joints with high temperature silicone
(500°F [260°C] minimum rated only).
NOTE: If burning shelled field corn, you must use
approved venting specifically designed for corn. Follow
the instructions from the venting manufacturer.
WARNING
Fire Hazard.
• Only LISTED venting components may be
used.
• NO OTHER vent components may be used.
Substitute or damaged vent components may
impair safe operation.
3. Distance from permanently closed windows:
a. Not less than 12 inches (305mm) below, horizontally
from or above.
4. Distance between bottom of termination and grade
should be 12 inches (305mm) minimum. This is conditional upon plants in the area, and nature of grade
surface. The grade surface must be a non-combustible
material (i.e., rock, dirt). The grade surface must not be
lawn. Distance between bottom of termination and public
walkway should be 84 inches (2134mm) minimum.
5. Distance to combustible materials must be 24 inches
(610mm) minimum. This includes adjacent buildings,
fences, protruding parts of the structure, roof overhang,
plants and shrubs, etc.
6. Termination Cap Location (Home Electrical Service)
WARNING
Vent surfaces get HOT, can cause burns if
touched. Noncombustible shielding or guards
may be required.
• Side-to-side clearance is to be the same as minimum
clearance to vinyl inside corners.
• Clearance of a termination cap below electrical service
shall be the same as minimum clearance to vinyl soffits.
• Clearance of a termination cap above electrical service
will be 12 inches (305mm) minimum.
• Location of the vent termination must not obstruct or
interfere with access to the electrical service.
Page 10
7014-082B
September 21, 2006
R
CB 1200 Pellet Stove
R
WARNING
C. Equivalent Feet of Pipe
The table below can help you calculate the equivalent feet
of pipe which is a method used to determine pellet vent size.
See Figure 11.1
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. Refer
to the owner’s information manual provided with this appliance. For assistance or additional information consult a
qualified installer, service agency or your dealer.
Example of 3 Elbow-Rear Vent Termination Calculaton
2 ft.
Pellet Venting
Component
90o Elbow or Tee
ft.
# of
Elbows
Multipled
By
Equivalent
Feet
Equivalent Feet
X
5
15
X
3
3
45o Elbow
2 ft.
Feet of
Pipe
Horizontal Pipe
7
X
1
Vertical Pipe
2
X
0.5
Components
7
1
23
Total Equivalent Feet
Note: This is a generic example and is not
intended to represent any specific fuel type.
2 ft.
Figure 11.1
D. Pipe Selection Chart
30
The chart will help you in determining proper
venting size according to the equivalent feet of
pipe calculated above and the altitude above sea
level of this installation. See Figure 11.2.
20
Equivalent Pipe
Length In Feet
Locate the calculated equivalent feet of pipe on
the vertical left side of the chart. Move to the
right horizontally on the chart until you reach
your altitude above sea level.
10
0
If you fall below the diagonal line, 3 or 4 inch (76
to 102mm) pipe may be used. If it is anywhere
above the diagonal line, a 4 inch (102mm) diameter pipe is required.
The chart reveals that a 90° elbow is 5 times as
restrictive to the flow of exhaust gases under
positive pressure as 1 foot of horizontal pipe, and
a foot of horizontal pipe is twice as restrictive as
a foot of vertical pipe.
Do NOT pack insulation or other
combustibles between firestops.
• ALWAYS maintain specified clearances
around venting and firestop systems.
September 21, 2006
2
3
4
5
6
7
8
9
10
Figure 11.2
Fire Risk.
Failure to keep insulation or other material
away from vent pipe may cause fire.
3 in. or 4 in. (76mm or 102mm) Diameter Pipe
1
ALTITUDE IN THOUSANDS OF FEET
WARNING
• Install firestops as specified.
4 in. (102mm) Diameter Pipe Only
CAUTION
Follow Chimney Connector Manufacturer’s Instructions
for Proper Installation.
ONLY use connector:
• Within the room, between appliance and ceiling or
wall.
Connector shall NOT pass through:
• Attic or roof space
• Closet or similar concealed space
• Floor or ceiling
Maintain minimum clearances to combustibles.
7014-082B
Page 11
CB 1200 Pellet Stove
5
R
Venting Systems
A. Alcove
A
C
D
B
Figure 12.1
Alcove Installation
A
B
C
D
not shown
Inches
Millimeters
Minimum Alcove Height
44
1117
Minimum Alcove Width
40-1/2
1029
Maximum Alcove Depth
36
915
Minimum Alcove Side Wall
6
152
Top of Unit to Combustibles
12-1/2
318
All minimums listed are to a combustible surface.
NOTE:
• Illustrations reflect typical installations and are FOR
DESIGN PURPOSES ONLY.
• Illustrations/diagrams are not drawn to scale.
• Actual installation may vary due to individual design
preference.
Page 12
7014-082B
September 21, 2006
R
CB 1200 Pellet Stove
R
B. Through The Wall
Horizontal termination cap must be a minimum of 12 inches.
(305mm) from the wall. Approved for mobile home installations. Must use 3 or 4 inch (76-102mm) “L” or “PL” listed
pellet venting or listed double wall pipe and a Quadra-Fire
outside air kit in mobile homes.
NOTE:
In Canada, where passage through a wall or partition of
combustible construction is desired, the installation shall
conform to CAN/CSA-B365
2 in.
(51mm)
Minimum
Straight Out
6 in.
(152mm)
Minimum
From Glass
Wall
Thimble
Horizontal
Termination
Cap
12 in.
(05mm)
Minimum
Non-combustible Hearth Pad
Figure 13.1
45 Degree
Illustration shows venting going in both directions.
Choose which one is best for your installation.
12 in. (05mm)
Minimum
Wall
Thimble
2 in. (51mm)
Minimum
12 in.
(05mm)
Minimum
2 in. (51mm)
Minimum
Figure 13.2
September 21, 2006
7014-082B
Page 13
CB 1200 Pellet Stove
R
c. Vertical
We recommend a minimum of 60 in.
(1524mm) vertical, however above the eave
is preferred.
Rain Cap
Flashing
Both installations are approved for mobile
home installations. Must use 3 or 4 inch (76
to 102mm) “L” or “PL” listed pellet venting or
listed double wall pipe and Quadra-Fire outside air kit in mobile homes. Single wall pipe
is approved for residential installations only.
24 in. (610mm)
minimum
Firestop
Ceiling Support
6 in.
(152mm)
Min.
Non-combustible Hearth Pad
Class A Chimney
Connector Adapter
in. (76mm)
Min.
Top Vent Kit
Clean-out
Cover
Figure 14.1
Rain Cap
d. Through The Wall & Vertical
Flashing
24 in. (610mm)
Minimum
2 in. (51mm) Minimum
6 in. (152mm)
Minimum
Support Bracket
every 60 in. (1524mm)
Wall Thimble
Tee
Clean-out Cover
Non-Combustible Hearth Pad
Figure 14.2
Page 14
7014-082B
September 21, 2006
R
CB 1200 Pellet Stove
R
WARNING
Fire Hazard
Inspection of Chimney:
• Masonry chimney must be in good condition.
• Meets minimum standard of NFPA 211
• Factory-built chimney must be 6 in. (152mm) UL103 HT.
e. Masonry
Concrete Cap
Fireclay Flue
Liner with Airspace
Flashing
1 in. (25mm) Clearance
with Firestop
1 in. (25mm) Clearance
in. (76mm) Minimum
6 in. (152mm)
Minimum
Sheathing
Cleanout Cover
Non-Combustible Hearth Pad
Airtight
Clean-out Door
Figure 15.1
F. Alternate Masonry
Concrete Cap
Fireclay Flue Liner
with Airspace
Flashing
1 in. (25mm) Clearance
with Firestop
1 in. (25mm)
Clearance
2 in. (51mm) Minimum
6 in. (152mm)
Minimum
Sheathing
Airtight Clean-out Door
Non-Combustible Hearth Pad
Figure 15.2
September 21, 2006
7014-082B
Page 15
CB 1200 Pellet Stove
6
R
Mobile Home
A. Mobile Home Installation
You must use a Quadra-Fire Outside Air Kit
for installation in a mobile home.
1.
An outside air inlet must be provided for the combustion
air and must remain clear of leaves, debris, ice and/or
snow. It must be unrestricted while the appliance is
in use to prevent room air starvation which causes
smoke spillage. Smoke spillage can also set off smoke
alarms.
2.
The combustion air duct system must be made of
metal. It must permit zero clearance to combustible
construction and prevent material from dropping into
the inlet or into the area beneath the dwelling and
contain a rodent screen.
3.
The appliance must be secured to the mobile home
structure by bolting it to the floor (using lag bolts).
Use the same holes that secured the appliance to the
shipping pallet.
4.
The appliance must be grounded with #8 solid copper
grounding wire or equivalent, terminated at each end
with an NEC approved grounding device.
5.
Refer to Clearances to Combustibles and floor protection requirements on pages 8 & 9 for listings to
combustibles and appropriate chimney systems.
6.
Use silicone to create an effective vapor barrier at
the location where the chimney or other component
penetrates to the the exterior of the structure.
7.
Follow the chimney manufacturer’s instructions when
installing the vent system for use in a mobile home.
8.
Installation shall be in accordance with the Manufacturers Home & Safety Standard (HUD) CFR 3280, Part
24.
CAUTION
Maintain structural integrity of mobile home:
• Floor, wall, ceiling and/or roof.
Do NOT cut through:
• Floor joist, wall, studs or ceiling trusses.
• Any supporting material that would affect the structural
integrity.
CAUTION
Never draw outside combustion air from:
• Wall, floor or ceiling cavity
• Enclosed space such as an attic or garage
Spark Arrestor Cap
Storm Collar
Roof Flashing
Joist Shield/Firestop
Double Wall
Pellet Vent
WARNING
Installation must comply with Manufactured Home and
Safety Standard (HUD), CFR 3280, Part 24.
Figure 16.1
WARNING
Never install in a sleeping room.
Page 16
7014-082B
September 21, 2006
7
R
CB 1200 Pellet Stove
R
Appliance Set-Up
A. Outside Air Kit Instructions
Included in Kit: 1 piece of 2 inch x 3 foot flex hose, 2 hose
clamps, 1 collar assembly, termination cap assembly, 1
trim ring, 12 screws.
Tools Needed: Phillips head screw driver; wire cutters;
hole saw or jig saw.
2. Floor Installation
a. Remove rear screen and set aside.
b. Install cover plate over hole in right rear floor.
c. Cut a 2 inch minimum hole in the floor to accommodate
flex hose.
d. Attach hose to termination cap.
1. Rear Installation
a. Measure distance from floor to air vent opening in appliance and mark location on wall.
Use saw to cut opening in wall. Cut a 2-1/2 to 3 inch
(64-76mm) opening on inside wall and a 3 to 3-1/2 inch
(76-89mm) opening on outside of house.
e. Place rope under pedestal to close off air leaks.
Screen
b. Use hose clamp to secure flex pipe to collar assembly.
c. Slide trim ring over flex pipe and run pipe through wall.
d. Attach hose to outside termination cap with second
hose clamp.
Install Cover Plate
e. Secure termination cap to outside surface.
f. Secure trim ring to interior wall.
Seal Pedestal with 26 in. Rope
g. Snip corners and remove plate. Figure 17.1.
h. Align and secure collar assembly with 2 of the 4 holes
as shown. Figure 17.2
Figure 17.3
Termination
Cap Assembly
Hose Clamp
Trim Ring
Snip Corners
and remove
plate
Figure 17.1
Secure Collar
O
N
Flex Hose
O
N
Figure 17.2
Hose Clamp
CAUTION
Never draw outside combustion air from:
• Wall, floor or ceiling cavity
• Enclosed space such as an attic or garage
September 21, 2006
Collar Assembly
Figure 17.4
7014-082B
Page 17
CB 1200 Pellet Stove
R
C. Rear Vent and Rear Vent to Top Vent
Adapter Installation
B. Top Vent Adapter Installation
3 to 3 inch Top Vent Adapter
3 to 6 inch Top Vent Offset Adapter
Installing the Top Vent Adapter
1.
Put a layer of high temperature silicone on the 3 inch
(76mm) exhaust outlet.
2.
Slide the top vent adapter onto the rear exhaust outlet
and adjust the assembly to a vertical position.
3.
Drill 4 holes with #26 drill bit (provided) into the back of
the appliance using the outer shield as a pattern (make
sure the assembly is vertical). Figure 18.1
4.
Install the 4 mounting screws.
5.
Install the vent pipe into the top vent adapter (be sure
to silicone all joints).
6
To clean the top vent adapter, open the clean-out cover.
See Figure 18.1
" - 6"
Offset
Adapter
Clean-Out Cover
Figure 18.2 - Rear Vent Adapter
Drill holes in back of
stove and secure with 4
screws, 2 on each side.
Clean-Out Cover
Figure 18.3 - Rear to Top Vent Adapter - 90o
Clean Out
Cover
" - "
Top Vent
Adapter
1.
Put a layer of high temperature silicone on the 3 inch
(76mm) exhaust outlet.
2.
Slide the adapter onto the rear exhaust outlet and adjust
the assembly to the appropriate position.
3.
Install the vent pipe into the adapter (be sure to silicone
all joints)
Figure 18.1
Page 18
7014-082B
September 21, 2006
R
CB 1200 Pellet Stove
R
E. Brick Clip Installation
D. Brick Set Installation
WARNING
1. Remove the baffle first, follow instructions on page 32.
2. Slide bottom of left rear brick in first; rotate top edge
toward rear of appliance and then rotate outer edge
toward rear of appliance, until brick slides into place.
Figure 19.1.
Risk of Injury.
• Brick may have small wires protruding from
the back of brick.
3. Repeat with right rear brick.
4. Place left side brick along left side of firebox, making sure
chamfered (beveled) back edge of brick fits snugly next
to rear brick. Figure 19.2.
1. After the brick set has been installed, 2 brick clips need
to be installed on the outer edge of each baffle to hold
the brick set in place.
5. Repeat with right side panel.
2. Remove 2 baffles from the appliance. Slide the baffle up
and the bottom edge should fall down and then lift the
baffle out.
6. Complete brick set, correctly installed. Figure 19.3.
3. Using pliers, bend the brick clip slightly past 90° in the
direction shown in Figure 19.4.
4. Position the brick clip as shown in Figure 19.4 and use
pliers to crimp around the outside edge of the baffle as
shown in Figure 19.5.
Note: Figure 19.5 shows the finished shape of the brick
clip, after being bent around the outside edge of
the baffle.
1
5. Slide the baffle back into place making sure that the brick
clip holds the side brick toward the wall of the firebox.
Push back on the sides so they will keep the rear bricks
in place. Repeat for opposite side.
Figure 19.1
Approximately
1 inch from corner
1
2
Outside edge
of Baffle
Top outside
corner of Baffle
Figure 19.2
Use pliers to crimp
Brick Clip around edge
Figure 19.4
Figure 19.3
September 21, 2006
1
2
4
Installed Clip
Figure 19.5
7014-082B
Page 19
CB 1200 Pellet Stove
R
F. Optional Log Set Placement Instructions
G. Optional Gold or Nickel Grille Assembly
CAUTION
CAUTION
Do not open top all the way back so the weight of the
top is supported by the hinges. It will damage the
hinges. It will be necessary to prop the top up with
a supporting brace. You can use the shipping box as
shown in Figure 1.
Logs are FRAGILE. Use extreme care when handling or
cleaning logs.
1. Place the front log in first as shown in Figure 20.1. Place
log between firepot and face of appliance with charred
area surrounding firepot.
2. Set the left and right twigs onto the log, placing the holes
in the base of twigs over the locating pins in log. See
Figure 20.2. Ensure that the charred ends are facing
the firepot.
1. Remove grille from packaging.
2. Lift top up and place shipping box in vertically.
3. Place 1 flap of the box lid into opening for stability.
4. Align the 3 holes in the stove with the holes in the grille.
5. Use a Phillips screwdriver to secure in place.
6. Remove shipping box and lower top.
Align the 3 hoes in the stove
with the holes in the grille and
secure in place.
Place 1 flap of
box lid into
opening for
stability
LOCATING PINS
CAUTION: Do not open top all the way back so the weight is
supported by the hinges. It will damage the hinges. Prop the
top up with supporting brace or use shipping box as shown.
Figure 20.1
Figure 20.3
Charred Areas in the Back
H. Installing Logo (Nickel Only)
1. Remove logo from packaging.
2. The logo has 2 studs on the back.
Left Twig
3.Install the logo on the lower left side of the center
panel by pressing the 2 studs into the pre-drilled
holes. See Figure 20.4.
Right Twig
Front Log
Figure 20.2
NOTE:
Due to the abrasive nature of a pellet appliance fire, the
logs are not covered under warranty. Any placement variation other than shown here can cause excessive heat and
shall void the appliance warranty.
Page 20
7014-082B
Install Logo
Figure 20.4
September 21, 2006
R
CB 1200 Pellet Stove
R
I. Door Installation
J. Thermostat Installation
To install door:
1.
A 12 volt AC thermostat is required to operate this pellet
appliance. You may use the included wall mount thermostat or purchase an optional programmable thermostat
or remote control. It is equipped with an adjustable
heat anticipator. The current rating is .05 amps. The
anticipator needs to be adjusted to the lowest setting
available.
2.
When mounting a thermostat on a wall, be sure to follow
your thermostat installation instructions carefully.
NOTE: Thermostat must be mounted level for
accurate readings. The thermostat should be
mounted on an inside wall and not in direct line
with the appliance convection air.
NOTE: If the thermostat is located too close to the
appliance, you may need to set the temperature
setting slightly higher to maintain the desired
temperature in your home.
3.
There is a 4 screw terminal block located on the back
lower left corner of the stove directly above the power
cord inlet. The center 2 screws are for the thermostat
wires.
1. Carefully remove door from packaging.
2. Line up hinges with hinge pins on appliance body, and slide
door down until it sits securely on pins. Figure 21.1.
3. If door is plated, be sure to clean all plated surfaces and
glass with a glass cleaner to ensure all oils are removed
before your first burn.
4. Remove all labels from glass before burning appliance.
To adjust latches:
1. Close door securely.
2. Place rod in slot on the bracket on the door and close
latch.
3. Latch must close tightly enough to ensure an airtight
seal between the door and the body of the appliance. To
increase tension on the latch, turn the rod clockwise a few
turns, then attempt to close the latch, until it is snug. Do not
overtighten; you should be able to close the latch with your
hand. Figure 21.2.
4. After adjusting the latch, place a Phillips head screw driver
in the end of the rod, and tighten the nut with a wrench.
This will maintain the correct tension on the rod and latch.
Hinge Pin
Hinge
Power Outlet
Figure 21.1
Rod and nut
Terminal Block.
Center 2 screws for
Thermostat Wires
Figure 21.3
Caution
Shock hazard.
• Do NOT remove grounding prong from plug.
• Plug directly into properly grounded 3 prong
receptacle.
• Route cord away from appliance.
• Do NOT route cord under or in front of appliance.
Rod and nut
Figure 21.2
September 21, 2006
7014-082B
Page 21
CB 1200 Pellet Stove
8
R
Operating Instructions
A. Fuel Size And Material
B. General Operating Information
1. Wood Pellets
1. Thermostat Calls For Heat
Fuel pellets are made from sawdust or wood by-products. If the
source material is hardwood, they can have a higher mineral
content, creating more ash. Fuels containing bark will also have
higher ash content. Minerals and other noncombustible materials
such as sand will turn into a hard, glass-like substance called
a clinker when heated to the extreme temperatures our firepot
reaches. This is what forms clinkers in the bottom of the firepot.
Trees from different areas will vary in mineral content. That is
why some fuels produce more clinkers than others. Pellets are
manufactured in either 1/4 inch or 5/16 inch (6-8mm) diameter and
should be no more than 1-1/2 inches (38mm) in length. Pellet
lengths may even vary by lot from the same manufacturer which
is why the feed rate may need to be adjusted occasionally. If you
burn pellets longer than 1-1/2 inches (38mm) you may have
an inconsistent fuel feed rate and/or missed ignitions.
The appliance is like most modern furnaces; when the
thermostat calls for heat, your appliance will automatically
light and deliver heat. When the room is up to temperature
and the thermostat is satisfied, the red call light will go off
and the appliance will shut down.
Pellet fuel quality can greatly fluctuate. We recommend using
premium grade fuel with ash content less than 1%. Even in some
fuel labeled “premium” ash content can vary from bag to bag and
possibly exceed 1%. High ash fuel, or lack of maintenance, can
cause the firepot to fill up and thus create a potential for smoking,
sooting and possible hopper fires.
Always burn dry fuel. Burning fuel with high moisture content takes
heat from the fuel and tends to cool the appliance, robbing heat
from your home. Damp pellet fuel can clog the feed system.
2. Heat Output Controls
This appliance is equipped with a heat output control
switch that has three settings or burn rates; low, medium
and high. The appliance will turn on and off as the
thermostat demands. When the thermostat calls for heat,
the appliance will start up on the high setting for the first 4
minutes and 15 seconds, then automatically switch to the
burn rate for which it is set. If the appliance is set at one
of the lower settings, it will run quieter but take longer to
heat up an area than if it were set at a higher burn rate.
Regardless of the burn rate, when the area is warm enough
to satisfy the thermostat, the appliance will shut off.
3. Fan Speed Switch
This switch will adjust the speed of the room distribution air
fan or convection blower on all three settings. This means
you have six different blower speeds available as there is
a high and low on each setting.
Heat
Output
We recommend that you buy fuel in multi-ton lots whenever
possible. Buying large quantities of fuel at once will greatly
reduce the number of times the feed adjustments will need to be
made. However, we do recommend trying various brands before
purchasing multi-ton lots to ensure your satisfaction.
Fan
Speed
HIGH
HIGH
MED
LOW
LOW
Reset Button
Call Light
WARNING
Fire Risk.
•
High ash fuels, or lack of maintenance,
can cause the firepot to fill with ash
and clinker. If the firepot fills to the top,
immediately shut down the unit and clean.
•
Failure to do so could result in smoking,
sooting and possible hopper fires.
Figure 22.1
WARNING
2. Shelled Field Corn
Extensive factory and field testing has demonstrated shelled
field corn to be an efficient and very economical fuel. We
recommend the use of a 50-50 blend of corn and wood pellets.
The only change in operation is that the feed rate may require
a slight adjustment. The BTU output of the appliance varies
slightly compared to pellets, depending on the quality of the
corn used. In cases where it is acceptable for the appliance to
run full time, 100% corn will work after the fire has been started
using wood pellets.
Page 22
•
•
•
•
7014-082B
Fire Hazard.
Keep combustible materials, gasoline
and other flammable vapors and liquids
clear of appliance.
Do NOT store flammable materials in the appliance’s
vicinity.
Do NOT use gasoline, lantern fuel, kerosene, charcoal
lighter fluid or similar liquids to start or “freshen up” a
fire in this heater.
Keep all such liquids well away from the heater while
it is in use.
Combustible materials may ignite.
September 21, 2006
R
CB 1200 Pellet Stove
R
C. Before Your First Fire
F. Fire Characteristics
1. First, make sure your appliance has been properly
installed and that all safety requirements have been met.
Pay particular attention to the fire protection, venting and
thermostat installation instructions.
A properly adjusted fire with the heat output control switch set
on “high” has a short active flame pattern that extends out of
the firepot approximately 4 to 6 inches (102 to 152mm). If
the fire has tall flames with black tails and seems somewhat
lazy, the feed rate will need to be reduced. This is done by
sliding the fuel adjustment control rod down, which will reduce
the feed. If the fire is not 4 to 6 inches (102 to 152mm) tall,
slide the fuel adjustment control rod up to increase the feed.
A medium and low setting will give a shorter flame. The flame
will rise and fall somewhat. This is normal.
2. Double check that the ash drawer and firebox are
empty!
3. Check the position of the thermocouple, located above
the firepot, and make sure that it protrudes approximately
3/4 inch (19mm) into the firepot.
4. Close the front door.
IMPORTANT DETAIL: The tip of the thermocouple must
be in contact with the inside end of the thermocouple
cover.
D. Fuel Adjustment Rod
The set screw is located at the bottom of the hopper and set
loose at the factory so the fuel adjustment control rod will slide
up and down by only loosening the thumb screw at the top.
See Figure 23.1. Do not re-tighten bottom set screw.
E. Starting Your First Fire
1. A thermostat is required for proper operation of this
appliance, except for corn. At this time, fill the hopper
with pellets, set the thermostat to its lowest setting. Plug
the power cord into nearby outlet.
G. Feed Rate Adjustment Instructions
The feed adjustment control rod is factory set, and should
be adequate for most fuels. However, if the flame height is
too high or too low, you will need to adjust the feed rate. Wait
until the appliance has been burning for 15 minutes before
making your adjustments and allow 15 minutes for feed
adjustment to take effect.
1. Loosen the thumb screw. Figure 23.1
2. Adjust the fuel adjustment control rod towards the "+"
symbol to increase the feed rate and flame height or
towards the "-" symbol, to decrease the feed rate and
flame height.
3. Re-tighten the thumb screw.
2. The exhaust blower will stay on for approximately 10
minutes even though the thermostat is not calling for
heat. This is normal.
3. Locate the heat output control switch mounted on the
upper right corner of the right side panel. Switch it to
the high setting by pushing the top of the switch in, then
adjust the thermostat to its highest setting. The red call
light located on the upper right corner of the right side
panel will be on. This indicates the thermostat is calling
for heat.
Fuel Adjustment
Rod
Thumb
Screw
Set Screw
4. The fuel feed system and the igniter should now be on.
5. For your first fire it will be necessary to press the reset
button every two minutes until pellets start to drop into
the firepot, then press button 1 more time. This will fill the
feed system and allow the appliance to begin dropping
pellets. The appliance will continue to run as long as the
thermostat is calling for heat.
Figure 23.1
6. Once the appliance has ignited, let the it burn for
approximately 15 minutes, then set the thermostat to the
desired room temperature. Adjust the heat output control
switch to the desired setting.
September 21, 2006
7014-082B
Page 23
CB 1200 Pellet Stove
R
H. Ignition Cycles
WARNING
Fire Risk
Do NOT operate appliance:
• With appliance door open.
• Firepot floor open.
• Cleaning slide plates open.
Do NOT store fuel:
• Closer than required clearances to combustibles to appliance
• Within space required for loading or ash
removal.
1. During each ignition cycle, it is normal to see some
smoke in the firebox. The smoke will stop once the
fire starts.
2. The convection blower will automatically turn on after
your appliance has reached the set temperature on
the “high” setting. This blower transfers heat from your
appliance into the room, and will continue to run after
the thermostat has stopped calling for heat until the
appliance has cooled down.
3. Occasionally the appliance may run out of fuel and shut
itself down. When this happens, the red call light will
be on. To restart it, fill the hopper and press the reset
button. (See Figure 22.1, page 22). When you press
the reset button the red call light will go out. Release
the button and the light will come back on. You should
see a fire shortly. If not, follow the instructions on page
23, of “Starting Your First Fire”.
CAUTION
Back side of Firepot
Odors and vapors released during initial operation.
• Curing of high temperature paint.
• Open windows for air circulation.
Odors may be irritating to sensitive individuals.
Firepot floor left open
Figure 24.1 - DO NOT LEAVE FIREPOT FLOOR OPEN
I. Frequently Asked Questions
ISSUES
SOLUTIONS
1. Metallic noise.
1. Noise is caused by metal expanding and contracting as
it heats up and cools down, similar to the sound produced by a furnace or heating duct. This noise does not
affect the operation or longevity of your insert.
2. Ash buildup on glass.
2. This is normal. Clean the glass.
3. Glass has turned dirty.
3. Excessive build up of ash. The lower burn settings will
produce more ash, the higher burn settings produce
less. The more it burns on low the more frequent cleaning of the glass is required.
4. Fire has tall flames with black tails and is lazy.
4. The feed rate needs to be reduced or the firepot needs
cleaning. Heat exchanger of exhaust blower needs
cleaning.
5. Smokey start-up or puffs of smoke from the airwash. 5. Either the firepot is dirty or there is too much fuel at
start-up and not enough air. Close down feed rate 1/4
inch at a time until this no longer happens.
6. Large flame at start-up.
Page 24
6. This is normal. Flame will settle down once the fire is
established.
7014-082B
September 21, 2006
R
9
CB 1200 Pellet Stove
R
With proper installation, operation, and maintenance your appliance will provide years
of trouble-free service. If you do experience a problem, this troubleshooting guide
will assist a qualified service person in the diagnosis of a problem and the corrective
action to be taken. This troubleshooting guide can only be used by a qualified service
technician.
Troubleshooting
Symptom
Plug in appliance - No
response.
Call light on. No fire.
No fuel in firepot.
Call light on. No fire.
Partially burned fuel in
firepot.
Possible Cause
Corrective Action
No current to outlet.
Check circuit breaker at service panel.
.7 amp fuse defective.
Replace fuse.
#3 snap disc tripped or defective.
Reset or replace snap disc.
Control box defective.
Replace control box.
Out of fuel.
Check hopper. Fill with fuel.
#2 snap disc may be defective.
Replace snap disc.
Vacuum switch not closing, no vacuum.
Check exhaust blower is plugged in and
operating.
Check vacuum switch is plugged in.
Check vacuum hose is in good condition,
clear and connected at both ends.
Check thermocouple is in good condition
and plugged in properly.
Make sure venting system is clean.
Make sure front door is closed.
Control box defective.
Replace control box.
Firepot clean-out plate not closed.
Check that firepot clean-out plate is fully
closed.
Firepot is dirty (missed ignition).
Clean firepot. Make sure there is no clinker
in the firepot.
Clinkers may have to be broken up with
firepot scraper tool or other means.
Call light on. No fire.
Unburned pellets in
firepot.
Firepot clean-out plate not closed.
Firepot is dirty.
Clean firepot. Make sure there is not a
clinker in the firepot. Clinkers may have to
be pushed out of firepot with firepot scraper
tool or other means.
Scrape with solid piece of wire.
Ignition hole blocked.
Remove ash drawer to see if igniter is
glowing red on start-up.
Check igniter wires for good connection.
Replace igniter using 1/4 inch male /female
spade connectors.
Igniter not working.
Slow or smoky start-up.
September 21, 2006
Check that firepot clean-out plate is fully
closed.
Control box defective.
Replace control box.
Firepot clean-out plate not closed.
Check that firepot clean-out is fully closed.
Firepot is dirty.
Clean firepot. Make sure there is not a
clinker in the firepot. Clinkers may have to
pushed out of firepot with firepot scraper
tool or other means.
Excessive amount of fuel at start-up.
Reduce feed rate using feed rate adjustment control rod located inside hopper.
7014-082B
Page 25
CB 1200 Pellet Stove
R
Symptom
Possible Cause
Corrective Action
Slow or smoky start-up
(Cont’d)
Dirty exhaust and/or venting system.
Check for ash build up in unit, including behind rear panels, firebox, heat
exchanger, exhaust blower and venting.
Feed system fails to
start.
Out of fuel.
Check hopper, fill with fuel.
#2 snap disc may be defective.
Replace snap disc. Firebox door must be
closed securely.
Vacuum switch not closing. No vacuum.
Check exhaust blower is plugged in and
operating.
Check vacuum switch is plugged in.
Check vacuum hose is in good condition,
clear and connected at both ends.
Check thermocouple is in good condition
and plugged in properly.
Make sure venting system is clean.
NOTE: High winds blowing into the venting system can pressurize the firebox
causing loss of vacuum.
Feed system jammed or blocked.
Empty hopper of fuel. Use a wet/dry
vacuum cleaner to remove remaining fuel,
from hopper, including feed tube.
Check feed chute for obstructions.
Loosen 2 screws and jiggle feed assembly.
Feed spring not turning with feed motor.
Check that set screw is tight on feed
spring shaft at end of feed motor.
Feed motor defective or not plugged in.
Check connections on feed motor, replace
if defective.
Thermostat not set to a high enough temperature.
Adjust thermostat above room temperature.
Snap Disc #3 tripped.
Reset snap disc.
No power.
Connect to power.
Fuse blown.
Replace fuse.
No call light. Unit
does not begin start
sequence.
Connections at thermostat and/or appliance not Check connections at thermostat and
making proper contact.
appliance.
Unit fails to shut off.
Page 26
Defective thermostat or thermostat wiring.
Replace thermostat or wiring.
NOTE: To test thermostat and wiring, use
a jumper wire at the thermostat block on
the unit to by-pass thermostat and wiring.
Control box defective.
Replace control box.
Call light on.
Turn thermostat off.
If call light does not go out, disconnect
thermostat wires from unit. If call light
does go out, thermostat or wires are
defective.
7014-082B
September 21, 2006
R
CB 1200 Pellet Stove
R
Symptoms
Convection blower fails to
start.
Exhaust blower fails to
start or does not shut off.
Large, lazy flame, orange
color. Black ash on glass.
Nuisance shutdowns.
Appliance calls for heat.
Call light illuminates.
Exhaust blower starts.
No feed or igniter.
September 21, 2006
Possible Cause
Corrective Action
#1 snap disc defective.
Replace snap disc.
Blower not plugged in.
Check that blower is plugged into wire harness.
Blower is defective.
Replace blower.
Control box is defective.
Replace control box.
Blower not plugged in.
Check that blower is plugged into wire harness.
Blower is clogged with ash.
Clean exhaust system.
Blower is defective.
Replace blower.
Control box is defective.
Replace control box.
Dirty appliance.
Poor fuel quality, high ash content.
Clean unit, including firepot, heat exchangers and venting system. Remove stainless
steel baffle from firebox to clean ash from
on top of baffle. Clean behind rear brick
panels. Change fuel brand to premium.
Firepot clean-out plate not completely
closed.
Check that firepot clean-out plate is fully
closed.
Excessive amount of fuel.
Reduce feed rate using feed rate adjustment
control rod located inside hopper.
Low flame.
Increase feed by opening feed rate adjustment control rod located inside hopper.
Sawdust buildup in hopper.
Clean hopper, see page 30.
Feed motor is reversing.
Check for good connections between feed
motor and wire harness.
Defective thermocouple.
Replace thermocouple.
Defective control box.
Replace control box.
Firepot more than 1/2 full.
See page 31 for detailed instructions for
“High Ash Fuel Content Management”
Thermocouple is defective or not properly
plugged in.
Check connections on thermocouple or
replace if defective.
A flashing yellow light on the control box
indicates a problem with the thermocouple.
Defective control box
Replace control box.
7014-082B
Page 27
CB 1200 Pellet Stove
R
10
Maintaining & Servicing Your Appliance
3. Cleaning Firepot with Cleaning Rod & Firepot
Scraper (Cont’d)
A. Proper Shutdown Procedure
Caution
Shock and Smoke Hazard
• Turn down thermostat, let appliance completely
cool and exhaust blower must be off. Now you
can unplug appliance before servicing.
• Smoke spillage into room can occur if appliance
is not cool before unplugging.
• Risk of shock if appliance not unplugged before
servicing appliance.
B. General Maintenance
b.Pull firepot cleaning rod OUT a couple of times to help
shake debris loose. If rod is hard to pull, it may be
necessary to use your firepot scraper to chip away
material that has built up on the bottom plate of the
firepot and to push out any clinkers. Larger clinkers
may have to be removed from the top of the firepot.
Corn clinkers can be especially difficult to break up.
c.The firepot floor plate must be fully closed when
finished.
4. Cleaning Ash Drawer
•
•
•
Frequency: As needed
By: Homeowner
Task:
1. Types of Fuel
The ash drawer is located in the pedestal. To remove
and empty the ash drawer, open both the left and right
side pedestal access doors. They are hinged in the back
and held closed magnetically. Pull out on the back of the
over-center style latch and then pivot the holding rod out
of the drawer notch on both sides. Pull the ash drawer
straight out of the pedestal and empty into a metal or
non-combustible container. Place the container in a
safe area, away from combustible materials. Re-install
the ash drawer and check that both latches are secure
and tight.
Depending on the type of fuel you are burning will dictate how
often you have to clean your firepot. If the fuel you are burning
has a high dirt or ash content or you are burning shelled field
corn, it may be necessary to clean the firepot more than once
a day. Dirty fuel will cause clinkers to form in the firepot. A
clinker is formed when dirt, ash or a non-burnable substance
is heated to 2000°F (1093°C) and becomes glass-like. See
“C” in this section for more details on fuels with high ash
content.
5. Ash Removal from Firebox
Clinker
•
•
•
Frequency: Weekly or as needed
By: Homeowner
Task:
a.There must not be any hot ashes in the firebox during
cleaning so allow the appliance to completely cool. The
firebox ash should be removed every time the firepot
is cleaned. Frequent cleaning of the ash in the firebox
will help slow down the build-up of ash in the exhaust
blower and vent system.
Figure 26.1 - Large Clinker
2. Cleaning Firepot with Cleaning Rod & Firepot
Scraper
•
•
•
Frequency: Daily or more often as needed
By: Homeowner
Task:
a.The appliance must be in complete shutdown and cool
and the exhaust blower off.
NOTE: Remove optional log set if installed.
b.Plug in your appliance, if unplugged, and turn the
thermostat on and immediately shut it off to start the
exhaust blower on its cycle time. It will pull fly ash out
the exhaust instead of into the room.
WARNING
WARNING
Fire Hazard.
Disposal of Ashes
• NEVER pull firepot cleaning rod when appliance is operating. Hot pellets may fall into
ashpan and may start a fire or you may experience mis-starts due to lack of vacuum.
Page 28
• Ashes should be placed in metal container
with tight fitting lid.
• Ashes should be retained in closed container
until all cinders have thoroughly cooled.
7014-082B
September 21, 2006
R
CB 1200 Pellet Stove
R
6. Ash Removal from Firebox (Cont’d)
9. Cleaning Beneath Heat Exchanger
c.See Cleaning Ash Drawer for instructions to remove
the ash drawer.
d. This ash is deposited in the same ash drawer as the
firepot debris. The ash drawer should be emptied every
time you clean the firebox. Remember to place the ash
and debris into a metal or non-combustible container.
• Frequency: Monthly or after burning 1 ton of fuel
• By: Homeowner
• Task:
A more thorough cleaning is needed to remove the excess
ash that is left behind from the use of the cleaning rods
for the heat exchanger tubes. Open the right side curtain
and the right pedestal access door. Remove 4 screws and
remove the exhaust clean-out plate and thoroughly vacuum
out the excess ash.
7. Disposal of Ashes
•
•
•
NOTE: There are heavy duty vacuum cleaners specifiically
designed for solid fuel appliance cleaning.
Frequency: As needed
By: Homeowner
Task:
Ashes should be placed in a metal container with a
tight-fitting lid. The closed container of ashes should
be placed on a non-combustible floor or on the ground,
well away from all combustible materials, pending final
disposal. If the ashes are disposed of by burial in soil
or otherwise locally dispersed, they should be retained
in the closed container until all cinders have been
thoroughly cooled.
WARNING
Heat exchanger cleaning rods may be warm
to the touch. For safety purposes wear
gloves.
Do not pull heat exchanger cleaning rods
while appliance is operating.
Exhaust Plenum
Clean-Out Plate
8. Cleaning Heat Exchanger Chambers
•
•
•
Figure 29.1
Frequency: Weekly or as needed
By: Homeowner
Task:
The amount of ash buildup in the firepot will be a good
guide to determine how often you should clean the heat
exchangers.
a. Allow the appliance to completely cool down before
pulling the cleaning rods. Turn the thermostat on and
then immediately off to start the exhaust blower on its
cycle time. It will pull fly ash out the exhaust instead
of into the room. Lift the stove top up from the front to
access the 2 cleaning rods. See Figure 29.2.
b. Locate the 2 rods along bottom edge of the heat
exchanger tubes. Lift the stove top up by the front.
Both rods are bent at a 90° angle for easy handling.
c.To clean, pull the rods straight out unit it stops,
approximately 20 inches (508mm). Slide the rods OUT
and IN a couple of times.
Cleaning Rods
Heat Exchanger Tubes
Figure 29.2
September 21, 2006
7014-082B
Page 29
CB 1200 Pellet Stove
R
10. Cleaning the Glass
13. Door Latch Inspection
•
•
•
Frequency: As needed
By: Homeowner
Task:
•
•
•
a. Appliance must be completely cool before cleaning
glass.
b.Use a damp paper towel or any non-abrasive glass
cleaner. Wipe off with dry towel.
The same latch is used on both the front door and the ash
drawer. To adjust, open the latch and pivot the holding
rod out. Loosen the jam nut on the rod. With a Phillips
head screw driver, turn the rod clockwise to tighten. The
latch handle should snap securely in place when adjusted
properly. After adjusting the latch, be sure to tighten the jam
nut on the rod to hold the adjustment.
CAUTION
Handle glass assembly with care.
Frequency: Periodically
By: Homeowner
Task:
14. Cleaning Convection Blower - Requires No
Lubrication
When cleaning glass:
• Avoid striking, scratching or
slamming glass.
• Do NOT clean glass when hot.
•
•
•
• Do NOT use abrasive cleaners.
• Use a hard water deposit glass cleaner on white film.
• Refer to maintenance instructions.
Frequency: Yearly or as needed
By: Qualified Service Technician
Task: Contact your local dealer.
15. Soot and Fly Ash: Formation & Need for Removal
in Exhaust Venting System.
•
•
•
WARNING
Handle glass with care.
• Inspect the gasket to ensure it is
undamaged.
• Do NOT strike, slam or scratch glass.
• Do NOT operate appliance with glass
assembly removed.
• Do NOT operate with glass cracked, broken or
scratched.
Frequency: Yearly or as needed
By: Qualified Service Technician/Homeowner
Task:
The products of combustion will contain small particles
of fly ash. The fly ash will collect in the exhaust venting system and restrict the flow of the flue gases. At
start-up if there is incomplete combustion, or if there
is a shutdown or incorrect operation of the appliance it
will lead to some soot formation. This will collect in the
exhaust venting system.
The venting system may need to be cleaned at least
once a year or more often depending upon the quality
of your fuel or if there is a lot of horizontal pipe sections. Ash will build up more quickly in the horizontal
sections.
11. Cleaning the Hopper
•
•
•
Frequency: Monthly or after burning 1 ton of fuel
By: Homeowner
Task:
After burning approximately 1 ton of fuel you will need to
clean the hopper to prevent sawdust build-up. A combination of sawdust and pellets on the auger reduces the
amount of fuel supply to the firepot. This can result in
nuisance shutdowns and mis-starts.
a. The appliance must be in complete shutdown. Allow the
appliance to completely cool down and then unplug it.
b Empty the hopper of any remaining pellets.
16. Cleaning the Top Vent Adapter
a.
The appliance must be in complete shutdown and the
exhaust blower should be off. Allow the appliance to
completely cool down.
b.
Open the clean-out cover. See Figure 28.1.
c.
Sweep out any ash build-up.
NOTE: There are heavy duty vacuum cleaners specifiically
designed for solid fuel appliance cleaning.
c. Vacuum the hopper and feed tube.
12. Cleaning Exhaust Blower - Requires No Lubrication
•
•
•
Frequency: Yearly or as needed
By: Quality Service Technician/Homeowner
Task:
a. Locate the blower on the left side of the appliance by
opening both the left side curtain and the left pedestal
access door. To clean the impeller it is easier to access
through the right side curtain.
Clean Out
Cover
Figure 28.1
Page 30
7014-082B
September 21, 2006
R
CB 1200 Pellet Stove
R
C. High Ash Fuel Content Maintenance
•
•
•
Frequency: As needed
By: Homeowner
Task:
Pellets Back Up
In Feed Tube
Firepot Overfills
Poor quality pellet fuel, or lack of maintenance, can create
conditions that make the firepot fill quickly with ashes and
clinkers. This condition makes the appliance susceptible to
overfilling the firepot with pellets which may result in smoking, sooting and possible hopper fires. Figure 31.1 shows an
example where the firepot overfills, pellets back up into the
feed tube and ash has accumulated in the firebox. Figure
31.2 illustrates an inefficient and non-economical method of
burning of fuel caused by poor quality pellet fuel. Figure 31.3
is showing the correct flame size when good quality, premium
pellet fuel is burned.
Ash Build Up in Firebox
Figure 31.1
Incorrect
If the ash buildup exceeds the half way point in the firepot
IMMEDIATE ATTENTION AND CLEANING IS REQUIRED.
Follow the detailed instructions found in this section for each
step listed below.
•Shut down the unit by turning down the thermostat and
allow unit to completely cool down. (Do not unplug the unit, it
can cause smoke spillage in the room).
•Pull the heat exchanger cleaning rods. Section 10.7
•Empty the firepot. Section 10.2
•Clean the firebox. Section 10.4
•Empty the ash drawer. Section 10.3
•Dispose of the ashes. Section 10.6
• Restart the appliance with premium grade fuel.
Tall, Lazy Flame, Orange in Color
Figure 31.2
Correct
Correct Flame Size, Yellow/White in Color
Figure 31.3
D. Blower Replacement
1. Convection Blower Replacement
a. Use proper shut down procedures to shut down the
appliance and let it completely cool.
b. The convection blower is located at the bottom rear
of the appliance. If an outside air kit is also installed,
depending on your particular installation you may or
may not have to remove the outside air flange. If you
do, remove the 2 screws using a Phillips head screwdriver. You do not need to remove the flex pipe from
the flange.
Remove
c. Remove the lower rear screen by removing the 4
screws securing the screen to the unit.
Remo
ve 4 S
e. Disconnect the wires from the blower. The wires coming
from the wiring harness are white, red and tan and the
wires coming from the blower are black, white and red.
The white connects to white, the red to red and black to
the tan color wire.
September 21, 2006
7014-082B
s
Outside Air
Flex Hose
d. The motor is mounted on a removable bracket. Remove the
2 screws just above the motor and the whole assembly will tilt
down and pull out.
2 Screw
crews
Convection Blower
Figure 31.4
Page 31
CB 1200 Pellet Stove
R
E. Igniter Replacement
2. Exhaust Blower Replacement
Remove existing blower:
a. Use proper shut down procedures to shut down the appliance and let it completely cool and then unplug it.
b. Use an 11/32" wrench or nut driver to loosen and remove
the (6) nuts holding motor mount plate to the blower
housing on your stove.
c. Remove washer from beneath the terminal ring on the
grounding wire.
d. Pull motor/mounting plate from blower housing.
Igniter Bracket
e. Scrape off old gasketing material from blower housing.
Thumb Screw
Install new blower:
Figure 32.1
f. The blower and blower housing is shipped as a unit. It
is necessary to separate them at this point if you are
using the existing blower housing already installed on
the appliance:
g. Follow steps 2 and 3 above. Discard or set aside the new
blower housing.
h. Carefully remove gasketing from new housing and set
onto the blower housing.
1.
Use proper shut down procedures to shut down the
appliance and let it completely cool down and then
unplug it and remove the ash drawer.
2.
Follow instructions to remove the ash drawer found on
page 28. Remove the access plate directly above it
by removing the 2 screws just below the ash catcher.
3.
The wire leads to the igniter are connected to the wire
harness with 1/4 inch male / female spade connectors.
These wires will pull forward approximately 4 to 5
inches (102mm to 127mm). Disconnect the spade
connections and remove the igniter from the chamber.
Loosen the thumb screw and slide igniter out.
4.
Install new igniter into the chamber and tighten the
thumb screw. Re-connect the wires to the 2 leads with
the spade connectors.
5.
Remove right side panel and pull wire leads back
toward the rear of the appliance to take-up the 4 to 5
inches (102mm to 107mm) previously pulled out. This
will keep the wires out of the way of the ash drawer.
Double check that the igniter wires are clear of any
movement, i.e. ash drawer, firepot cleaning rod, etc.
6.
Re-install the ash drawer and side panel and re-connect
the power.
Re-install blower to blower housing:
i.
Igniter
Install blower on housing ensuring that wiring exits facing
the 8 o’clock position. Place the washer and then the
grounding wire on nearest mounting plate stud.
j. Use nuts removed in step b to secure blower to housing.
k. Re-connect wiring (use jumper wire if necessary). Reconnect power supply.
F. Baffle Removal
1. Use proper shut down procedures to shut down the
appliance and let it completely cool down.
2. Open right side panel and then open the door.
3. The 2 baffles are located at the top inside of firebox.
4. Place your hand on the baffle and slide it up and the
bottom edge will fall down and then you can lift the baffle
out. Repeat for the other side.
Page 32
7014-082B
September 21, 2006
R
CB 1200 Pellet Stove
R
G. Glass Replacement
WARNING
Door Latch
• Glass is 5mm thick high temperature heatresistant ceramic glass.
Top & Bottom Frame
• DO NOT REPLACE with any other material.
• Alternate material may shatter and cause
injury.
Center Posts
•
Remove door from appliance and place face down on
a protected surface to avoid scratching the door.
•
Remove all door rope.
Glass
Side
Frame
Replacing Center Glass
NOTE: DO NOT LET Air Wash Spacers fall down from
top frame when removing and replacing center
glass.
1. Using a nut driver remove the (5) bottom nuts and
remove the bottom glass frame. Figure 33.2.
2. Slightly bend up and out of the way the 2 center posts
and slide the glass out the bottom.
3. Slide new glass in, reposition the 2 center posts and
re-install bottom glass frame.
Figure 33.1
Remove Door Latch First
and then Side Frame
4. Re-rope the door.
Door Frame
shown with no
Glass or Glass
Frames
Replacing Side Glass
NOTE: When removing the side glass with the door
latch, you must remove the door latch first
before removing the side frame. Use a powered Phillips head screw driver to remove the
4 screws.
1. Remove side glass frame.
Remove 5 nuts from Bottom Frame
2. Loosen the top and bottom frame and slightly bend up
and out of the way.
3. Slide glass out the side and slide new glass in.
Figure 33.2
4. Re-install the side glass frame and tighten the top and
bottom frames.
5. Re-install the door latch, if applicable, and re-rope the
door.
September 21, 2006
7014-082B
Page 33
CB 1200 Pellet Stove
11
R
Reference Materials
A. Component Function & Location
1. Control Box
E
When describing the location of a component,
it is always AS YOU FACE THE FRONT OF
THE APPLIANCE.
a. The control box is located under a small cover in the
right rear corner of the inside of the hopper.
b.There is a light located inside of the control box. The
internal light will turn green when the appliance has
reached a temperature of 200oF (93°C) in the firepot
and will turn red when it reaches 600oF (315°C).
The heat exchangers transfer hot air from the exhaust system
into convection air. Lift the stove top to access the heat
exchangers. There are 2 clean out rods located under the
heat exchangers.
c. There is also an internal blue light located in the upper
left corner of the control box. When you plug in the
appliance the blue light will automatically start blinking
1 blink every 10 seconds for the first 60 seconds and
then will stop.
The heat output switch is located on the upper right side panel.
The function of the heat ouput switch is to regulate the burn
rates; low, medium, and high settings.
NOTE:
Do NOT open the control box. This will void the
warranty. If you need to plug in or remove the control
box you must first unplug the appliance.
2. Convection Blower
The convection blower is mounted at the bottom rear of the
appliance. There are 2 impellers, one on each side of the
motor. The convection blower pushes heated air through the
heat exchange system into the room.
3. Exhaust Blower
The exhaust blower is mounted on the lower left side on
rear of appliance. The exhaust blower is designed to pull
the exhaust from the appliance and push it out through the
venting system.
4. Feed System
The feed system is located in the hopper under the feed
motor cover box on the left side of the appliance and can
be removed as an entire assembly. The assembly includes
the feed motor, mounting bracket, bearing and feed spring
(auger). The hollow feed spring (auger) pulls pellets up the
feed tube from the hopper area and drops them down the
feed chute into the firepot.
5. Firepot
The firepot is made of high quality ductile iron and has a
cleaning pull-out rod. The floor of the firepot opens for
cleaning when you pull out the rod. Be sure that the floor
returns to a completely closed position or your appliance will
not operate properly.
6. Fuse
The fuse is located on the front of the junction box on the
right side of the appliance. The fuse will blow should a short
occur and shut off power to the appliance.
Page 34
7. Heat Exchangers
8. Heat Output Switch
9. Igniter
The igniter is mounted on the base of the firepot. Combustion
air travels over the red hot igniter creating super heated air
that ignites the pellets.
10. Junction Box And Wiring Harness
The junction box is located on the right side of the appliance,
behind the interior shield. The junction box and wiring harness
are replaced as one component.
11. Power Supply
The power outlet is located on the back of the appliance,
lower right corner. Check the wall receptacle for 120 volt,
60 Hz (standard current). Make sure the outlet is grounded
and has the correct polarity. A good surge protector is
recommended.
12. Red Call Light
The red call light is on the front of the junction box, next to the
reset button. The function of the red call light is to indicate
that the thermostat is calling for heat.
13. Reset Button
The reset button is located on the right side of the apppliance
next to the red call light. The function of the button is to
momentarily open the thermostat circuit, which restarts the
system.
14. Thermocouple
The thermocouple is located on top of the firepot inside
the thermocouple cover (ceramic protection tube). The
thermocouple sends a millivolt signal to the control box
indicating the preset temperatures of the green and red lights
have been obtained.
15. Thermostat
The appliance is designed to run on a 12 volt AC thermostat.
The heat anticipator should be set on the lowest setting
available.
7014-082B
September 21, 2006
R
CB 1200 Pellet Stove
R
16. Snap Disc #1 (Convection Blower) 145°F
Snap disc #1 is located on the right side of the appliance on
the top of the heat exchanger box. There are 2 purple wires
connected to it. This snap disc turns the convection blower
on and off as needed. Power is always present at snap disc
#1.
17. Snap Disc #2 (Thermostat Override) 200°F
Snap disc #2 is also located on the right side of the appliance
between snap disc #1 and convection blower. There are 2
yellow wires connected to it. This snap disc will turn off the
feed system, which will turn off the appliance if an overfire
condition should occur or if the convection blower should fail
to operate.
18. Snap Disc #3 (Back Burn Protector) 250°F
box from inside the hopper. If the fire tries to burn back
into the feed system or push exhaust up the feed tube, this
snap disc will shut the entire system off. This disc must be
manually reset.
19. Vacuum Switch
The vacuum switch is located on the left side of the appliance
behind the inner shield. This switch turns the feed system on
when vacuum is present in the firebox. The vacuum switch
is a safety device to shut off the feed motor if the exhaust
or the heat exchanger system is dirty or plugged or if the
firebox door is open.
20.Wiring Harness
See Figure 35.1 below.
Snap disc #3 is mounted on the back of the auger tube in the
right side of the appliance just below the feed motor and has
a red reset button. To access it remove the feed motor cover
Female
Male
Blue
Gray
White
Thermostat
Block
Yellow
Heat
Output
Switch
Yellow
Thermocouple
Vacuum
Switch
Capacitor
Blower
Speed
Snap
Disc #2
Yellow
Purple
Red
Orange
White
Blue
Black
Black
Yellow
Red
Purple
Gray
Blue
High Temp
High Temp
Feed
Motor
Snap
Disc #1
Convection
Blower
Exhaust
Blower
Call Light
Reset
Button
Snap
Disc #
Fuse
Igniter
Figure 35.1
September 21, 2006
7014-082B
Page 35
CB 1200 Pellet Stove
R
B. Component Locations
Cleaning Rods
Heat
Output
Fan
Speed
HIGH
HIGH
MED
LOW
LOW
Reset Button
Call Light
Heat Exchanger Tubes
Figure 36.3
Figure 36.1
Power Outlet
Outside Air
Flex Hose
Terminal Block.
Center 2 screws for
Thermostat Wires
Figure 36.2
Page 36
Convection Blower
Figure 36.4
7014-082B
September 21, 2006
R
CB 1200 Pellet Stove
R
C. Exploded Views
8
Nbr
7
6
5
9
4
Description
Part Number
1
Door Frame
MBK: 410-6300
Gold: 410-5530
Nickel: 510-1110
2
Glass Assembly, Center
510-5400
3
Glass Assembly, Sides
510-5410
4
Glass Frame Post
410-6240
5
Glass Frame Side
410-4740
6
Door Latch Bracket
410-4912
7
Glass Frame Spacer
410-6250
8
Glass Frame, Top & Bottom
410-4730
9
Hinge, Female
450-2910
2
1
Glass Size Center: 13-7/8” wide x 11” high
Glass Size Sides:
5-1/8” wide x 11” high
Figure 37.1 - Door, Face, Glass & Door Latch Assembly
Nbr
47
14
48
4
42
44
Description
Part Number
42
Firepot Pull Rod (Linkage)
812-3850
44
Igniter Bracket
Not Replaceable
13
Thumb Screw
7000-223
45
Igniter (Heating Element)
812-3811
43
Firepot, EZ Clean
812-3351
48
Thermocouple Holder
812-3171
14
Thermocouple
812-0210
47
Thermocouple Cover
812-1322
1
45
Figure 37.2 - Firepot Assembly
September 21, 2006
7014-082B
Page 37
CB 1200 Pellet Stove
R
6
7
5
29
4
8
0
28
2
9
27
1
48
26
47
42
40
4
44
45
41
46
25
2
24
Figure 38.1
Nbr
Page 38
Description
Nbr
Description
23
Door Assembly
36
Baffle, Left
24
Ash Pan
37
Curtain Mount, Side, Left
25
Panel Access, Front (Firepot)
38
Curtain, Side, Left
26
Latch, Draw
39
Curtain, Pedestal, Left
27
Director, Air, Large
40
Blower, Exhaust
28
Director, Air, Small
41
Gasket, Exhaust Blower
29
Grille, Louvers
42
Firepot Pull Rod Assembly (Linkage)
30
Knob, Heat Exchanger Rods
43
Firepot, EZ Clean
31
Brick, Right Side
44
Igniter Bracket (Thumb Screw)
32
Brick, Right Rear
45
Igniter, Loop
33
Brick, Left Rear
46
Exhaust Plenum Trap Door
34
Brick, Left Side
47
Thermocouple, Cover
35
Baffle, Right
48
Thermocouple Holder
7014-082B
September 21, 2006
R
CB 1200 Pellet Stove
R
68
69
72
66
67
65
71
64
6
70
62
61
60
7
74
75
77
76
56
59
55
54
52
58
5
51
57
Figure 39.1
Nbr
Description
51
Exhaust Plenum Clean-Out Plate
52
Snap Disc, #1, 145-40 degree
53
Blower, Convection
54
Convection Air Plenum
55
Snap Disc, #2, 200 degree
56
Curtain Mount, Side, Right
57
Exhaust Plenum Plate
58
Curtain, Pedestal, Right
59
Curtain, Side, Right
60
Panel Access, Lower Rear Screen
61
Curtain, Air Deflector, Right
62
Latch, Magnet for Side Air Deflector Curtain
63
Panel Access, Upper Rear Screen
64
Vacuum Switch
September 21, 2006
Nbr
7014-082B
Description
65
Control Box
66
Control Box Cover
67
Feed Adjustment Plate with Rod
68
Feed Motor Cover
69
Feed Motor & Spring Assembly
70
Curtain, Air Deflector, Left
71
Hopper Lid
72
Hopper Lid Handle
73
Top Only
74
Hopper Access Plate
75
Heat Shield Extension, Top
76
Snap Disc, #3, 250 degree
77
Junction Box & Wire Harness
Page 39
CB 1200 Pellet Stove
R
D. Service Parts and Accessories
IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on the QuadraFire web site at www.quadrafire.com. When ordering, supply serial and model numbers to ensure
correct service parts.
Item #
Parts (Alphabetical Order)
Part No.
24
Ash Pan
812-4050
36
Baffle Assembly, Left
510-5350
35
Baffle Assembly, Right
510-5360
53
Blower, Convection
812-3370
40
Blower, Exhaust
812-3381
Bolt, Firepot, 1-1/4” long
225-0120
Bracket, Door Hinge
410-4840
Bracket, Door Latch
410-4912
Collar Assembly, Outside Air Kit
7001-045
Component Pack (Includes firepot scrapper, touch-up paint, power cord & wiring harness
to the thermostat and manual, owner’s manual, warranty card, consumer’s view card and
“How-To-Operate” DVD)
812-3630
65
Control Box
SRV7000-205
66
Cover, Control Box
410-6321
68
Cover, Feed Motor
410-5311
37
Curtain Mount, Side, Left
410-5251
56
Curtain Mount, Side, Right
410-5261
61
Curtain, Air Deflector, Left
410-4992
70
Curtain, Air Deflector, Right
410-5105
Curtain, Pedestal, Sides (interchangeable)
410-5391
38
Curtain, Side, Left
812-3840
59
Curtain, Side Right
812-3800
1
Door Frame
MBK: 410-6300
Gold: 410-5530
Nickel: 510-1110
6
Door Latch Bracket
410-4912
51
Exhaust Plenum Clean-Out Plate
410-4871
46
Exhaust Plenum Trap Door
812-4100
67
Feed Adjustment Plate with Rod
812-4170
Feed Motor
812-4421
Feed Motor & Spring Assembly
812-3690
Feed Motor Capacitor Jumper
230-2150
Feed Motor Mount
410-7172
Feed Spring Only
812-3600
Fireboard, Set, 4 pcs
811-0601
39,58
69
31-34
Firepot Floor (Slide Plate)
414-0290
42
Firepot Pull Rod Assembly (Linkage)
812-3850
43
Firepot, EZ Clean
812-3351
Fuse .7 amp, Junction Box
812-0380
Gasket, Ash Pan, 10 ft
834-1460
Gasket, (Rope) Door, cut to size, 7-1/2 ft
842-2350
Gasket, Exhaust Blower
240-0812
Gasket, Firepot
510-0530
Glass Assembly, Center
510-5400
41
2
Page 40
7014-082B
September 21, 2006
R
CB 1200 Pellet Stove
R
Item #
3
Service Parts (Alphabetical Order)
Part No.
Glass Assembly, Left or Right, 1 pc
510-5410
Grille, Bar, Bottom
410-8330
4
Glass Frame Post
410-6240
5
Glass Frame Side
410-4740
7
Glass Frame Spacer
410-6250
8
Glass Frame, Top & Bottom
410-4730
72
Handle, Hopper Lid
200-0110
Heat Output Control Switch, (Rocker Switch), 3 position
812-3500
75
Heat Shield Extension, Top
410-5322
Hinge, Female, Door
450-2910
71
Hopper Lid
410-4901
45
Igniter, Loop (Heating Element)
812-3811
77
Junction Box & Wire Harness
SRV7000-154
Knob, Firepot Pull Rod
200-0831
Latch, Draw
229-0640
Latch, Magnet for Side Air Delfector Curtain
812-3821
Nut, Firepot, 1/4-20
226-0090
Panel Access, Bottom Rear Screen
812-4020
Panel Access, Feed Motor
410-6220
25
Panel Access, Front (Firepot)
410-5161
63
Panel Access, Top Rear Screen
410-4352
Power Cord
812-1180
62
60
Rivnut Repair Kit, 1/4-20
RIVNUT-REPAIR
52
Snap Disc, #1, 145-40 Degree
230-0060
55
Snap Disc, #2, 200 Degree
230-0900
76
Snap Disc, #3, 250 Degree
230-1290
Switch, Rocker (Fan Speed)
812-3910
Termination Cap Assembly, Outside Air
7011-044
16
Thermocouple
812-0210
47
Thermocouple Cover
812-1322
48
Thermocouple Holder with Set Screw
812-3171
12
Thumb Screw
7000-223
Top Assembly with Hopper Lid
812-3940
73
Top Only
410-4980
64
Vacuum Switch
7000-166
Accessories
Part No.
Accessories
Part No.
Brick, Set, 4 pc
811-0601
Outside Air Kit, Floor
811-0570
Log Set, 3 pc
811-0592
Outside Air Kit, Rear
811-0872
Door Assembly, Black
DR-CB12-BK
Rear Vent Adapter
811-0620
Door Assembly, Gold
DR-CB12-GD
Rear to Top Vent Adapter, 90o
811-0610
Door Assembly, Nickel
DR-CB12-NL
Thermostat, Mechanical
811-3760
Grille Assembly, Black
LVGRL-CB12-NL
Thermostat, Programmable
811-0520
Grille Assembly, Gold
LVGRL-CB12-GD
Top Vent Adapter, 3 in x 3 in
811-0580
Grille Assembly, Nickel
LVGRL-CB12-MBK
Top Vent Offset Adapter Collar, 3 in x 6 in
812-3570
September 21, 2006
Appliance
Part No.
Classic Bay 1200 Pellet Stove
CB1200
7014-082B
Page 41
CB 1200 Pellet Stove
R
E. Service And Maintenance Log
Date of Service
Page 42
Performed By
Description of Service
7014-082B
September 21, 2006
R
CB 1200 Pellet Stove
R
F. Warranty Policy
Lifetime Warranty
LIMITED LIFETIME WARRANTY
The Hearth & Home Technologies limited Lifetime Warranty guarantees that the following components will work as designed for the
lifetime of the stove or Hearth & Home Technologies will repair or replace them. These items include but are not limited to steel and
cast iron components, all gas burners, gas logs, combustion chambers, heat exchanger systems, stainless steel firebox components,
plating, doors, glass damaged by thermal breakage, steel baffle supports, steel and ceramic baffles and manifold tubes. Labor is for
the first five years.
THREE YEAR WARRANTY
Our pellet firepots are covered under Hearth & Home Technologies three-year warranty program. Labor is for 3 years.
TWO YEAR WARRANTY
All electrical components such as but not limited to blowers, wiring, vacuum switches, speed controls, control boxes, thermodisc switches, pilot assembly, gas valves, thermostats and remotes are covered under Hearth & Home Technologies two-year warranty program.
Effective April, 2005 igniters are also covered under the two year warranty. Labor is for two years.
ONE YEAR WARRANTY
Porcelain and Powder Coat finishes are warranted against manufacturer defects for one year. Labor to repair or replace these parts is
covered for one year, reimbursed per our warranty service fee schedule.
CONDITIONS
This warranty is non-transferable and is made to the original retail purchaser only provided that the purchase was made through an
authorized dealer of Hearth & Home Technologies. It must be installed and operated at all times in accordance with the Installation and
Operating Instructions furnished with this product, as well as any applicable local and national codes. Any alteration, willful abuse, accident, or misuse of the product shall nullify this warranty.
Labor to repair or replace items covered under the limited Lifetime Warranty will be covered for the first five years per our warranty service fee reimbursement schedule. Parts covered under the limited Lifetime Warranty will be covered for the lifetime of the appliance up
to a maximum of ten (10) years after Hearth & Home Technologies discontinues the model and two (2) years for optional accessories.
Adjustments, regular maintenance, cleaning and temporary repairs do not qualify for a service call fee and will not be covered. The
replacement of consumer replaceable items and installation of upgraded component parts do not quality for a service call fee, and will
not be covered.
This limited Lifetime Warranty does not extend to or include surface finish on the appliance, door gasketing, glass gasketing, glass,
firebrick, pellet logs, kaowool or other ceramic insulating materials. It does not cover installation or operational-related problems such
as overfiring, use of corrosive driftwood, downdrafts or spillage caused by environmental conditions, nearby trees, buildings, hilltops,
mountains, inadequate venting or ventilation, excessive offsets, or negative air pressures caused by mechanical systems such as furnaces, fans, clothes dryers, etc.
Any installation, construction, transportation, or other related costs or expenses arising from defective part(s), repair, replacement, etc.,
will not be covered by this warranty, nor will Hearth & Home Technologies assume responsibility for them. Further, Hearth & Home
Technologies will not be responsible for any incidental, indirect, or consequential damages, except as results in damage to the interior
or exterior of the building in which this appliance is installed. This limited Lifetime Warranty does not apply to the venting components,
hearth components or other accessories used in conjunction with the installation of this product not manufactured by Hearth & Home
Technologies
This warranty is void if the stove has been overfired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging chemicals, the stove is subjected to prolonged periods of dampness or condensation, or there is any damage to the stove or other
components due to water or weather damage which is the result of, but not limited to, improper chimney or venting installation. Hearth
& Home Technologies may, at its discretion, fully discharge all obligations with respect to this warranty by either repairing or replacing
the unit, or refunding the wholesale price of the defective part(s).
This limited Lifetime Warranty is effective on all appliances sold after May 1, 2002 and supersedes any and all warranties currently in
existence.
Policy 250-8620 Rev K
September 21, 2006
7014-082B
Page 43
R
CONTACT INFORMATION:
Hearth & Home Technologies
1445 North Highway
Colville, WA 99114
Division of HNI INDUSTRIES
www.quadrafire.com
Please contact your Quadra-Fire dealer with any questions or concerns.
For the number of your nearest Quadra-Fire dealer
please call 1-800-926-4356
CAUTION
Do NOT discard this manual.
• Important operating and maintenance
instructions included.
• Read, understand and follow these instructions for safe installation and operation.
• Leave this manual with party responsible
for use and operation.
Your Records for Model:
CB1200 PELLET STOVE
WHERE PURCHASED:
SERIAL NUMBER:
__________________
______________________________________
DATE PURCHASED:
__________________
_______________________________________
DATE INSTALLED:
__________________
_______________________________________
TELEPHONE: __________________
This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 4811534,
5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407,
5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099,
6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579,
6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, 6769426, 6774802, 6796302, 6840261, 6848441, 6863064,
6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408,
2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending.
Page 44
7014-082B
September 21, 2006
Download PDF

advertising