Freestyle 789 Watch User Manual

789 SHARK™
INSTRUCTIONS
FEATURES:
• CURRENTTIME (HR., MIN.,
& SEC.)
• DAY/MONTH/DATE
• CHRONOGRAPH WITH SPLIT
& LAP TIMES
• DUALALARMS ( 1 DAILY
REPEATING, 1 NONREPEATING REMINDER.)
• COUNTDOWN, COUNTDOWN
REPEAT, COUNTDOWN
CHRONO
LAP & COUNTDOWN CHRONO
SPLITTIMERS
• DUAL TIME
• HOURLY CHIME
• OPTIONAL24-HR. TIME
(MILITARYTIME. )
• WATER RESISTANT TO
300 FT.
• NIGHT VISION™ ELECTROLUMINESCENT
BACKLIGHTING
NORMAL TIME MODE
( The term “Mode” means the function status of the watch.) Normal
time mode shows hours, minutes,
seconds, day and date. To set time,
see operating instructions on How
to Set Normal Time.
LT
RT
LB
RB
NORMAL TIME MODE
KEY TO SYMBOLS
LT - Left Top (Light/Set)
LB - Left Bottom (Mode)
RT - Right Top (Start/Stop)
RB - Right Bottom (Lap/Reset)
HOW TO SETNORMAL TIME,
DATE AND 24-HOUR FORMAT
Note: While in the setting mode,
the Night Vision™ backlight will
remain illuminated. If no buttons
are pressed for approximately ten
seconds, the watch will exit the
setting mode.
From Normal Time mode, press
and hold the light/set button LT for
approximately three seconds; the
seconds digits will flash. Pressing
the Start/Stop button RT will reset
the seconds digits to 0. If seconds
are greater than 30, one will be
added to the minutes digit.
LT
RT
LB
RB
To set minutes, press Mode button
LB; single minutes digit will flash. To
advance flashing minutes digit, press
Start/Stop button RT;hold for rapid
advance.
LT
LB
RT
LB
LT
RT
LB
RB
RB
To set tens of minutes, press Mode
button LB; tens of minutes will flash.
To advance flashing tens of minutes
LT
(“LAP” flag will be displayed for lap
mode and “SPL” flag will be
displayed for split time mode.)
Split time is the time elapsed since
the start of the chronograph. To use
the split time feature, “SPL” flag
must be displayed. Press
Start/Stop button RT to start
chronograph. “SPL” flag will begin
flashing. Press Lap/Reset button
RB to view split time. Chronograph
will continue to count while split
time is displayed. To release split
time and return to running chronograph, press Lap/Reset button RB.
RT
RB
press Start/Stop button RT; hold for
rapid advance.
Continuing through the setting
mode, the setting sequence is a
continuous loop of: seconds • single
minutes • tens of minutes • hours •
day/month/date • 12/24-hour mode,
and looping back to seconds. When
setting is complete, press Light/Set
button LT to return to normal time
mode.
HOW TO OPERATE
CHRONOGRAPH/STOPWATCH
The chronograph will record a
maximum of 99 hours, 59 minutes
and 59 seconds. Press Mode
button LB once from normal time
mode to enter the chronograph
mode. Normal time will remain on
LT
RT
LB
RB
the lower row, chronograph on the
upper row. “CH” flag will be displayed.
Reset the chronograph to zero by
pressing Lap/Reset button RB.
Press the Light/Set button LT to
switch between Lap and Split
mode.
Each press of Lap/Reset button RB
will display a split time.
To stop chronograph, press Start/Stop
button RT. Reset the chronograph to
zero by pressing the Lap/Reset button
RB. Lap time is the time elapsed since
the previous lap. To use the lap time
feature, “LAP” flag must be displayed.
Reset the chronograph to zero by
pressing the Lap/Reset button RB.
Enter LAPmode by pressing Light/Set
button LT. Press Start/Stop button RT
to start chronograph. “LAP” flag will
begin flashing. Press Lap/Rest button
RB to view lap time. Chronograph will
start counting next lap while lap time is
displayed. To release lap time and
return to running chrono, press
Lap/Reset button RB. Each press of
Lap/Reset button RB will display a lap
time.
LT
RT
LB
RB
To stop chronograph, press
Start/Stop button RT. Reset the
chronograph to zero by pressing
the Lap/Reset button RB.
HOW TO SET AND OPERATE THE
ALARMS AND HOURLY CHIME
From normal time mode, press
Mode button LB twice to enter the
alarm mode. Normal time remains
on the lower row, alarm time on the
upper row. Pressing Lap/Reset button RB will toggle between alarm 1,
indicated by “A1” flag, and alarm 2,
indicated by “A2” flag. Alarm 1 is a
daily, repeating alarm,and alarm 2
LT
RT
LT
RT
LB
RB
LB
RB
is a one time only reminder alarm.
Press and hold Light/Set button LT
for approximately three seconds to
enter alarm setting mode. The minutes digit will flash. Press Start/Stop
button RT to advance the flashing
minutes digit.
LT
RT
LB
RB
Press Mode button LB to advance
tens of minutes. Press Start/Stop
button RT to advance the flashing
tens of minutes digit.
LT
RT
LB
RB
Press mode button LB to advance the
hours digit. Press Start/Stop button
RT to advance the flashing hours
digit. While setting the flashing hours
digit, “A” or “P” is displayed next to
alarm. “A” designates a.m. and “P”
designates p.m.
LT
RT
LB
RB
Press Light/Set button LT to exit
the alarm setting mode. To activate
the alarm while in alarm mode:
Press Start/Stop button RT to
activate the alarm ((•)) and/or
hourly chime .
LT
RT
LB
RB
Note the setting sequence is: alarm
on, chime on, both alarms on, both
alarms andchime off.
Again, press Lap/Reset button RB
to toggle between alarm 1 and
alarm 2. Alarm 2 is set and
activated the same way as alarm 1.
A1 ((•)) = alarm 1 set.
A2 ((•)) = alarm 2 set.
A1 A2 ((•)) = alarm 1 & 2 set.
= hourly chime on.
HOW TO OPERATE THE
COUNTDOWN TIMER
Press Mode button LB three times
from the normal time mode to enter
the countdown timer mode. Normal
time will remain in the lower row
and the timer will appear on the
continued...
upper row. “TR” flag will be
displayed. (Minimum time setting is
one minute; maximum time setting
is 99 hours, 59 minutes).
*Note: there are four timer functions
in this mode. To select between
these features, press Lap/Reset
button RB until the desired function
(noted by its respective flag) is displayed.
TIMER COUNTDOWN - “TR” flag
will be displayed. This function will
countdown from a preset time.
When the countdown time is reached,
the timer will beep and will automatically reset to the preset time.
LT
LB
LT
RT
LB
RB
and hold the Light/Set button LT
for three seconds. The minutes digit
will flash. To advance the flashing
minutes digit, press Start/Stop button
RT.
Press Mode button LB to advance
to the tens of minutes digits, and
LT
RT
LB
RB
RB
hours digits. Press Start/Stop
button RT to advance the flashing
digit. When desired timer time is
set, press Light/Set button LT to
exit the setting mode. To start or
stop timer, press Start/Stop button
RT. To reset a stopped timer, press
Lap/Reset button RB.
LT
LB
RB
HOW TO OPERATE THE NIGHT
VISION ™ ELECTROLUMINESCENT
BACKLIGHT
Press Light/Set button LT to activate
the Night Vision™ electroluminescent
backlight. This light will remain illuminated for approximately four seconds.
RB
RT
RB
TIMER COUNTDOWN CHRONO
SPLIT- Press Lap/Reset button
RB; “CH,” “SPL” and “TR” flags will
be displayed. This function will
countdown from a preset time. When
the countdown time is reached, the
timer will beep and automatically
start a chronograph. This chronograph has a chrono split timer,
identical to that in the
chronograph/stopwatch “SPL” mode.
To set the countdown time, press
CARE AND MAINTENANCE
1. Back case cover should only be
removed by an authorized watch
repair specialist.
2. Always rinse your watch in fresh
water after immersion in salt or chlorinated water.
3. Do not expose watch or band to
chemicals such as gasoline, aerosol
sprays, paint or solvents.
4. Periodically clean with a soft cloth
and fresh water.
RT
RB
RT
LAP- Press Lap/Reset button RB,
“CH,” “LAP” and ”TR” flags will be
displayed. This function will countdown from a preset time. When the
countdown time is reached, the
timer will beep and automatically
start a chronograph. This chronograph
has a chrono lap timer, identical to
that in the chronograph/stopwatch
“LAP” mode.
LT
LB
RT
WARRANTY INFORMATION
LB
LB
LT
RT
TIMER COUNTDOWN REPEATPress Lap/Reset button RB; “TR”
and “RE” flags will be
displayed. This function will
countdown from a preset time.
When the countdown time is
reached, the timer will beep,
automatically reset, and begin
counting down repeatedly until the
Start/Stop button RT is pressed.
TIMER COUNTDOWN CHRONO
LT
flags are visible in this mode,
however, they are set to the normal
time mode.
HOW TO SET DUAL TIME
Press Mode button LB four times to
enter the dual time mode from the
normal time mode. The dual time
mode is indicated by the “T2” flag.
Press and hold the Light/Set button
LT for approximately three seconds;
LT
LB
RT
RB
the minutes digits will flash. Press
Start/Stop button RT to advance.
Continue through the setting
sequence as done in normal time setting by cycling between Mode button
LB and Start/Stop button RT.
Press Light/Set button LT to exit
the setting mode.
LT
RT
LB
RB
Note: Press and hold Start/Stop
button RT to temporarily display the
day and date of the normal time
mode. Note: The alarm and chime
REMEMBER: NEVER INCLUDE A SPECIAL WATCHBAND OR ANYOTHER
ARTICLE OF PERSONAL ARTICLES OF
VALUE IN YOUR SHIPMENT.
Send to the following address and be sure
to mark ATTN: INDIVIDUAL RETURNS.
Freestyle
Attn: Individual Returns
5855 Olivas Park Drive
Ventura, CA 93003
(805) 477-1200 ext.240
Please allow 20 days for return of your
watch.
Neither this warranty, nor any other warranty expressed, is assumed for any incidental or consequential damages, including but not limited to the mathematical
accuracy of the product. Some states do
not allow limitations on how long an
implied warranty lasts, or the exclusions of
or limitations on consequential damages,
so the above limitations may not apply to
you. This warranty gives you specific legal
rights, and you may have other rights
which vary from state to state.
This warranty applies to watches purchased in the United States. For watches
purchased outside the United States,
please contact your authorized Freestyle
dealer for warranty information.
Visit our website at:
w w w. f r e e s t y l e u s a . c o m
Freestyle warrants, to the original purchaser,
that its watches are free from defects in
materials and workmanship for a period of
ten (10) years under normal use. The warranty excludes batteries, crystal, watch case
plating, and strap/bracelet/band. The warranty excludes normal wear and tear and
abuse.
Special note: Freestyle® watches are
designed and engineered to be highly
water-resistant, and to withstand the most
active of lifestyles. The most important
component in keeping your watch waterresistant is the case back O-ring, which prevents water from entering the watch through
the case back.
Water leakage most often occurs after
improper battery replacement. We strongly
recommend having a certified jeweler, watch
repair technician or Freestyle's service center replace your battery. Water leakage due
to improper battery replacement is not covered under warranty.
Should your Freestyle® watch require warranty service, send it along with the following:
1. Acopy of your sales receipt
2. Your printed name and address
3. Your telephone number
4. Abrief description of the problem
5. If your watch was purchased within the
last year, there is no charge for processing and handling; if your watch was purchased more than 12 months ago, please
include $8.00 for processing and handling, using one of the following payment
methods:
-Check
-Money Order
-Credit Card (be sure to include card number and expiration date)
789004-1-2 rev. 3/02
Freestyle
Attn: Individual Returns
5855 Olivas Park Drive
Ventura, CA 93003
PRICE
Battery
Case or Crystal
Bezel
Band(Leather)
Band(Nylon)
Band(Metal)
Band(Polyurethane or
Neoprene)
California residents
add 7.25% sales tax
Processing and handling
TOTAL
$ 4.00
10.00
6.00
10.00
6.00
15.00
10.00
8.00
Total
$_____
❏ Check or money order
❏ Master Card
❏ Visa
___
Account #
Expiration Date
___
Printed Name
___
Address
___
___
Phone Number
___
Email Address
___
Signature (required for credit purchases)
789004-1-2 rev. 3/02