Freestyle 818 Watch User Manual

MONTH format, DATE and Daylight
Savings Time (DST).
The chime setting will start first.
Press S3 to turn the chime on or off.
Press S2 to move on to the next
setting sequence then press S3 or
S4 to adjust. Once the setting is
completed press S1 to exit this mode
and return to normal time.
818 OUTSIDER™
WATCH INSTRUCTIONS
FEATURES:
• TWO TIME ZONES WITH
AUTO CALENDAR
• THERMOMETER RANGE
FROM -20 DEGREES C TO
+60 DEGREES C
• HI AND LO TIDE TIME DATA
FOR THE PRESENT AND
FUTURE TIMES
• TIDE DATA FOR 30 PRESET
AND 5 CUSTOM LOCATIONS
• CHRONOGRAPH MODE
WITH SPLIT FUNCTION
• SEQUENTIAL HEAT TIMER
WITH 4 ADJUSTABLE
PRESET VALUES
• WATER-RESISTANT TO
500 FT./150M
• NIGHT VISION™ ELECTROLUMINESCENT
BACKLIGHTING
KEY REFERENCES
To view the second time zone (T2),
simply press the S4 button.Holding
this down for at least four seconds
will switch you between T1 and T2.
In TIME mode, press the MODE
button once to enter the
TEMPERATURE mode. The
temperature sensor is located on
the right side of the watch case. The
sensor reads ambient temprature,
which is an average of body, air or
water temperature.
The accuracy of this sensor is +/1.8ºF if the reading is between 23ºF
and 122ºF and +/-3.6ºF if the reading
is below 23ºF and over 122ºF.
Pressing S4 shows the offset
temperature reading in row 1. This
can be applied to offset your body
temperature when it is worn on
your wrist.
S1
HI
LO A
A
P
HI
LO A
A
S2
S3
S1- EL/ SET
S2- MODE
S3- RESET/ SCROLL DOWN
S4- START/ SCROLL UP
ROW 1
P
A
HI
LO A
ROW 2
ROW 3
ROW 4
There are seven modes of
operation: TIME, TEMP, TIDE,
BEACH, HEAT, CHRONO and
ALARM.These are sequentially
arranged in a cycle.
HOW TO SET TIME, DATE AND
24-HOUR FORMAT
From TIME mode: press and hold
the EL/SET button for approximately
three seconds to enter the time
setting mode. The setting will be
done in a cycle of sequences
beginning with CHIME, HOUR,
MINUTE, SECOND, 12/24 hour
format, YEAR, MONTH-DAY/ DAY-
HII
P
To adjust the values and offset press
down S1 for at least three seconds
until the temperature unit flashes.
Select between FHT for farenheit
or CEL for celsius. Pressing S2
moves you on to the offset
setting.Press S3 or S4 to adjust the
reading.
The concept of offsetting can be
best explained with an example.
Wear the watch on your wrist and
wait for at least 10 minutes until the
sensor factors out your body heat.If
the temperature reads 10 ºF above
the mercury thermometer then this
means that your body (and other
internal watch components) causes
the watch to be10 ºF warmer. 10ºF
is the value that you would be
offseting.
HEAT TIMER MODE
From TIME mode, press the MODE
button four times to enter the
HEAT timer mode.
There are four sequential countdown
timers and one independent timer
for you to set.There are preset
values on them but this could be
adjusted to suite your needs.
LO A
To select which preset timer you
want to use press S3. To start and
stop the countdown press S4. To
reset to the preset value or 0
press S3.
A
TEMPERATURE MODE
S4
P
To view future tide press S4 button
to advance one day. Hold down the
button to advance the dates faster.
The return to the current date
press S3.
To change the preset values press
S1 for three seconds until the hour
numbers flash. Press S3 or S4 to
adjust to the desired setting.
BEACH MODE
From TIME mode, press S2 three
times to enter the BEACH mode.
This mode shows the current
location of the tide reading as well
as upcoming tide information. You
can select through five different
locations by pressing S4.
To set your location press S1 for at
least three seconds until the wave
graph turns off. Press S3 to toggle
between the preset and custom
location settings. Under preset
mode, press S4 to select from the
30 preset locations stored. Once
this is set press S2 to move on to
setting the time difference. Since a
formula is used to predict the
tide times, they are average data
which are not affected by more
recent weather conditions. Compare
this tide data with more recent and
certified versions like that provided
by NOAA (National Oceanic and
Atmospheric Administration). If there
is a great variance between the tide
datas you can adjust the time
difference by pressing S3 or S4.You
can adjust this up to +/- 99 minutes.
If you want to choose a custom
beach setting toggle S3 until Custom
1 shows on the screen. There are
five spaces available for custom
location. You would need to find the
high tide time and date of the specific
location you want to input. Press S2
to enter the tide setting mode. The
setting will be done in a sequence
of: HOUR, MINUTE, YEAR,
MONTH, DAY and LOCATION. To
type in the location name press S4
to select the letter and press S3 to
move to the next space. To move
back select the arrow symbol then
press S3. Once everything is set
press S1.This process can be
repeated to set the rest of
the locations.
To proceed to the next HEAT press
S1. After you have confirm all preset
values you can adjust the number
of repititions (RP) in HEAT 4. Press
S1 to exit the setting mode.
To start or stop the countdown,
press S4 button to reset press S3.
CHRONOGRAPH MODE
In TIME mode, press MODE button
five times to enter the
CHRONOGRAPH mode.
To measure elapsed time, press the
S4 ST/STP button to start and stop
the counter. To get split times press
S3 while the counter is running.
To reset the chronograph, press the
S3 button when the counter is
stopped.
ALARM MODE
In TIME mode, press MODE button
six times to enter the ALARM mode.
This watch has two daily, two weekly
and one scheduled alarm.
You can turn each alarm on or off
individually by pressing S4 and scroll
through them by pressing S3.
To set the daily alarm press and
hold S1 for at least 2 seconds.The
setting sequence starts with the hour
then minutes. Once you are done
press S1 to exit the setting mode.
To set the weekly alarm press and
hold S1 for at least 2 seconds.The
setting sequence is: hour, minute,
day and preset. Presets are
common events that help remind
you what the alarm is for. The
available presets are: PARTY,
DATE, SURF, CALL, MEETING,
REMINDER.
In TIME mode, the fin logo and bell
symbol would indicate that an alarm
is activated.
TIDE MODE
HII
P
From TIME mode, press S2 twice
to go to TIDE mode. Rows 2 and 3
indicates the tide times for the day
including the ones that have past.
The wave graphic in row 4
corresponds to the tide times in
row 3.
A
LO A
HOW TO OPERATE THE NIGHT
VISION™ ELECTROLUMINESCENT BACKLIGHT
Press the EL/SET button to activate
the Night Vision™ electroluminescent backlight. The light will
remain illuminated for approximately
five seconds.
TIDE LOCATIONS:
Below is the list of preset locations
with tide data up to the year 2099:
1. BODEGA BAY, CA
2. SANTA CRUZ POINT, CA
3. RINCON, CA
4. SAN CLEMENTE, CA
5. SAN DIEGO, CA
6. PENSACOLA, FLA
7. VIRGINIA BEACH, VA
8. CAPE HATTERAS, N
9. SEBASTIAN INLET, FLA
10. SAN JUAN, PUERTO RICO
11. RECIFE, BRAZIL
12. RIO DE JANIERO, BRAZIL
13. CAP FERRET, FRANCE
14. CORPUS CHRISTI, TX
15. DURBAN, SOUTH AFRICA
16. REUNION ISLAND, INDIAN
OCEAN
17. COLOMBO, SRI LANKA
18. BALI, INDONESIA
19. GOLD COAST AUSTRALIA
20. SYDNEY, AUSTRALIA
21. SENDAI, JAPAN
22. ENOSHIMA, JAPAN
23. MIYAZAKI, JAPAN
24. HILO, HAWAII
25. LAHAINA, MAUI
26. HONOLULU, OAHU
27. HANAPEPE BAY, KAUAI
28. CABO SAN LUCAS, MEXICO
29. PUERTO ESCONDIDO, MX
30. DOMINICAL, COSTA RICA
CARE AND MAINTENCE
1. Back case cover should only be
removed by an authorized watch
repair specialist.
2. Always rinse your watch in fresh
water after immersion in salt or
chlorinated water.
3. Do not expose watch or band to
chemicals such as gasoline, aerosol
sprays, paint or solvents.
4. Periodically clean with a soft cloth
and fresh water.
NOTE: Extreme electrostatic
discharge can cause the LCD to
‘freeze up’. In this event you could
reset the watch by pressing all 4
buttons together for 5 seconds.
warranty excludes batteries, crystal,
watch case plating, and strap/
bracelet/ band. The warranty
excludes normal wear and tear
and abuse.
Special note: Freestyle® watches
are designed and engineered to be
highly water-resistant, and to
withstand the most active of
lifestyles. The most important
component in keeping your watch
water-resistant is the case back Oring, which prevents water from
entering the watch through the case
back.
Water leakage most often occurs
after improper battery replacement.
We strongly recommend having a
certified jeweler, watch repair
technician or Freestyle's service
center replace your battery. Water
leakage due to improper battery
replacement is not covered under
warranty.
Should your Freestyle® watch
require warranty service, send it
along with the following:
1. A copy of your sales receipt
2. Your printed name and address
3. Your telephone number
4. A brief description of the problem
5. Please include $8.50 for
processing and handling, using
one of the following payment
methods:
-Check
-Money order
-Credit card (be sure to include
card number and expiration date)
REMEMBER: NEVER INCLUDE A
SPECIAL WATCHBAND OR ANY
OTHER PERSONAL ARTICLES
OF VALUE IN YOUR SHIPMENT.
Send to the following address:
Freestyle
Attn: Individual Returns
47-50 33rd Street
Long Island City, NY 11101
DISCLAIMER ON TIDE DATA
Not for navigation. This program is
furnished in the hope that it will be
useful, without the implied warranty
of merchantability or fitness for a
particular purpose. Do not use this
program as a basis for any decisions
that could result in harm to people,
other organisms, or property. Check
these predictions against officially
sanctioned tables. Agencies like
NOAA exist because there is a need
for certifiably correct tide predictions.
Do not rely on these predictions if
you need guaranteed results.
Neither this warranty, nor any other
warranty expressed, is assumed for
any incidental or consequential
damages, including but not limited
to the mathematical accuracy of the
product. Some states do not allow
limitations on how long an implied
warranty lasts, or the exclusions of
or limitations on consequential
damages, so the above limitations
may not apply to you. This warranty
gives you specific legal rights, and
you may have other rights which
vary from state to state.
Remember that weather conditions
affect tidal ranges and current
speeds, sometimes very strongly.
This warranty applies to watches
purchased in the United States.
For watches purchased outside the
United States, please contact your
authorized Freestyle® dealer for
warranty information.
Freestyle U.S.A. warrants, to the
original purchaser, that its watches
are free from defects in materials
and workmanship for a period of ten
(10) years under normal use. The
Battery
Case
Bezel
Band(Polyurethane)
Band(Leather)
Band(Metal)
Band(Nylon)
Processing and handling
$ 4.00
10.00
6.00
12.00
12.00
20.00
7.00
8.50
Total
________
$
Check or Money Order
Master Card
Visa
__________________________________
Account#
Expiration Date
__________________________________
Printed Name
__________________________________
Address
(718)-729-8890
Please allow 30 days for return of
your watch.
WARRANTY INFORMATION
Attn: Individual Returns
47-50 33rd Street
Long Island City, NY 11101
(718)-729-8890
If your watch requires servicing not
covered under our warranty (battery,
crystal, strap/bracelet/band, watch
case plating), or refurbishing,
complete the return form (next
column) and return with your watch.
__________________________________
__________________________________
__________________________________
Phone Number
__________________________________
Signature
818004-4
Download PDF

advertising