Friedrich CP24F30 Air Conditioner User Manual

CP15F10A
/
Table of Contents
Air Conditioner Safety ......................................................................................................................................................1
Installation Requirements ...............................................................................................................................................3
Tools and Parts....................................................................................................................................................................3
Location Requirements .......................................................................................................................................................3
Electrical Requirements ......................................................................................................................................................4
Installation Instructions..................................................................................................................................................6
Unpacking ...........................................................................................................................................................................6
Window Installation (on some models)...............................................................................................................................7
Through-the-Wall Cabinet Installation ...............................................................................................................................9
Complete Installation ........................................................................................................................................................ 10
Air Conditioner Use ......................................................................................................................................................... 11
Starting Your Air Conditioner—Digital Control ..............................................................................................................12
Remote Control Operation ................................................................................................................................................ 13
Normal Sounds.................................................................................................................................................................. 13
Air Conditioner Care........................................................................................................................................................ 14
Cleaning the Air Filterr ...................................................................................................................................................... 14
Cleaning the Front Panel................................................................................................................................................... 14
Repairing Paint Damage ................................................................................................................................................... 14
Annual Maintenance......................................................................................................................................................... 14
Troubleshooting............................................................................................................................................................... 14
Assistance or Service...................................................................................................................................................... 15
Warranty........................................................................................................................................................................... 16
1
General Instructions
This Installation and Operation Manual has been designed to insure maximum satisfaction in the performance of your unit. For
years of trouble-free service, please follow the installation instructions closely. We cannot overemphasize the importance of
proper installation. We have added new information to the basic instructions to help you achieve success.
WARNING
WARNING
Refrigeration system under high pressure.
Please read this manual thoroughly prior to equipment
installation or operation.
Do not puncture, heat, expose to flame or incinerate.
R410A systems operate at higher pressures than R22
equipment. Appropriate safe service and handling
practices must be used.
It is the installer’s responsibility to properly apply and
install the equipment.
Installation must be in
conformance with the NFPA 70-2008 National Electric
Code or current edition, International Mechanic Code
2009 or current edition and any other applicable local
or national codes.
Only use gauge sets designed for use with R410A. Do
not use standard R22 gauge sets.
Failure to do so can result in property damage,
personal injury and / or death.
Only certified refrigeration technicians should service
this equipment.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual
and on your appliance. Always read and obey all safety messages.
This is a safety Alert symbol. This symbol alerts you
to potential hazards that can kill or hurt you and
others.
All safety messages will follow the safety alert
symbol with the word “WARNING” or “CAUTION”.
These words mean:
WARNING
Indicates a hazard which, if not
avoided, can result in severe
personal injury or death and damage
to product or other property.
CAUTION
Indicates a hazard which, if not
avoided, can result in personal injury
and damage to product or other property.
All safety messages will tell you what the potential hazard is, tell you
how to reduce the chance of injury, and tell you what will happen if
the instructions are not followed.
NOTICE
followed.
Indicates property damage can
occur if instructions are not
2
K
K.
pan-head Phillips screws(2)
Window installation
Electrical Requirements
Window opening measurements:
27"min. to 42" max. (76.2 cm to 101.6 cm) opening width (A).
20" min. (50.8 cm) opening height (B).
A
B
A.27" min. (76.2 cm)
B . 20" min. (50.8 cm)
Ground wire must be connected to ground screw located in lower
right corner of air conditioner when air conditioner is in cabinet.
The electrical ratings for your air conditioner are listed on the
model and serial number (nameplate) label. The model and serial
number label is located behind the front panel on the flange below
the control panel area.
Specific electrical requirements are listed in the chart below.
Follow the requirements for the type of plug on the power supply
cord.
Through-the-wall installation
The wall opening measurements should be:
Height (A): 17 ¼" plus twice thickness of wood used to build
frame
Width (B): 26 ¼"
Depth (D): 4" minimum to 8" maximum.
Power supply
cord
Wiring requirements
CP15
■
115-volt (103.5 min. - 126.5 max.)
■
0-12 amps
■
15-amp time-delay fuse or circuit breaker
■
Use on single outlet circuit only.
■
230-volt (207 min. - 253 max.)
■
0-12 amps
■
15-amp time-delay fuse or circuit breaker
■
Use on single outlet circuit only.
C
A
B
D
CP18 / CP24
¹⁄₄"
(0.6 cm)
C
A. 17 ¼"
B. 26 ¼"
C. Wood thickness
D. 4" minimum to
8" maximum.
4
Recommended grounding method
This air conditioner must be grounded. This air conditioner is
equipped with a power supply cord having a grounded 3 prong
plug. To minimize possible shock hazard, the cord must be
plugged into a mating, grounded 3 prong outlet, grounded in
accordance with all local codes and ordinances. If a mating outlet
is not available, it is the customer' s responsibility to have a
properly grounded 3 prong outlet installed by a qualified electrical
component installer.
It is the customer' s responsibility:
To contact a qualified electrical installer, and
To assure that the electrical installation is adequate and in
conformance with National Electrical Code, ANSI/NFPA 70 latest edition, and all local codes and ordinances.
Copies of the standards listed may be obtained from:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269
To test your power supply cord:
1. Plug power supply cord into a grounded 3 prong outlet.
2. Press RESET.
3. Press TEST (listen for click; Reset button will trip and pop
out).
4. Press and release RESET (listen for click; Reset button will
latch and remain in). The power supply cord is ready for
operation.
NOTES:
The Reset button must be pushed in for proper operation.
Power Supply Cord
NOTE: Your unit’s device may differ from the ones shown.
A
B
RESET
TEST
The power supply cord must be replaced if it fails to trip when
the test button is pressed or if it fails to reset.
Do not use the power supply cord as an off/on switch. The
power supply cord is designed as a protective device.
RESET
TEST
A damaged power supply cord must be replaced with a new
power supply cord obtained from the product manufacturer
and must not be repaired.
The power supply cord contains no user serviceable parts.
Opening the tamper-resistant case voids all warranty and
performance claims.
B
A
A. Reset button
B. Test button
This room air conditioner is equipped with a power supply cord
required by UL. This power supply cord contains state-of-t he-art
electronics that sense leakage current. If the cord is crushed, the
electronics detect leakage current and pow er will be
disconnected in a fraction of a second.
5
Window Installation (on some models)
NOTES:
■ Handle air conditioner carefully and gently.
■
Be sure your air conditioner cabinet does not fall out of the
opening during installation or removal.
■
The place where the power cord exits the air conditioner
should be no more than 4 ft (122 cm) from a grounded
3 prong power outlet.
■
Do not block the louvers on the front panel.
■
Do not block the louvers on the outside of the air conditioner.
Bottom view
A
B
A. Curtain housing
B. Curtain bottom channel on air conditioner
Attach Top Channel
3. Extend right-hand curtain outward so you may insert the
first screw through the middle hole of the curtain. Using #10 x
¹⁄₄" pan-head Phillips screw, screw curtain to middle hole in
air conditioner cabinet.
NOTE: This screw is required to correctly attach curtain (top
to bottom) to the air conditioner cabinet.
NOTE: Attach top channel and side curtains to air conditioner
cabinet before placing cabinet in window.
1. Locate provided bag of screws.
2. Place top channel on top of air conditioner cabinet, lining up
the 4 holes in top channel with the 4 holes on top of air
conditioner cabinet.
3. Using 4 - #10 x ³⁄₈" washer-head Phillips thread-cutting
screws, attach top channel to air conditioner cabinet.
A
B
4. While the right-hand curtain is still extended, insert #10 x ¹⁄₄"
pan-head Phillips screws into the top and bottom slots of
curtain. Screw curtain to the top and bottom holes in the air
conditioner cabinet side.
5. Slide the curtain housing into the curtain channels as far as it
will go.
6. Repeat above steps for the left-hand curtain.
A. Top channel
B. #10 x ³⁄₈" washer-head Phillips thread-cutting screws
Attach Side Curtains
Attach foam adhesive seal
1. Locate provided bag of screws.
2. Insert top and then bottom of right-hand curtain housing in
top and bottom curtain channels on air conditioner.
Attach foam adhesive seal along the bottom of the curtain
bottom channel.
Top view
A
B
A
B
A. Curtain housing
B. Foam adhesive seal
A. Curtain housing
B. Curtain top channel on air conditioner
7
7
12
■
3. Insert cabinet into the framed wall opening. the top of the cbine
should extend ¾" (19.1 mm) into the room. If there is trim, the
cabinet should extend ¾" (19.1 mm) past the trim.
Use 2" x 4" or thicker lumber for wood frame.
A
B
B
A
C
A. Outside width
B. Outside height
C. Depth
4. Apply wood preservative to the outside exposed surface.
5. Insert the frame in the wall opening. Square and level frame.
6. Attach frame securely to the wall.
A. ³⁄₄ " (19.1 mm) extending into room
B. Trim
Install Cabinet into Wood Frame
1. Remove top channel and both side channels using a ¹⁄₄" nut
driver or socket wrench. Discard top channel and both side
channels.
4. Use a level to check that cabinet is level side to side.
2. Cut two pieces
i
off standard
t d d 1" lumber
l b (supplied
(
li d by
b installer)
i t
to the
length and width required. Place in front and back of bottom sill
channel. Secure with nails (supplied by installer).
A
¾" Minim
mum
Front edge of louvers must alwayss
be outside of exterior wall surface
A. Level
Cabinet front
5. Check that air conditioner cabinet is tilted to the outside so that
water will run to the outside.
1" Thick lumbe
er
6. Reuse the insulation to seal opening between cabinet and
frame.
1" Minim
mum
Inside wall
Exterior wall
wa
¼" Slope down.
Position and secure cabinet
downward. Slope outside for
drainage.
7. Use existing holes in sides and top of cabinet and 7 - #10 x 1"
wood screws (not provided) to attach cabinet to frame.
NOTE: Do not overtighten screws or cabinet will distort and
provide a poor air seal between cabinet and air conditioner.
Max. Wall thickness allowed 8 ½"
8. Caulk all outside wall openings around cabinet.
Complete Installation
NOTE: Handle air conditioner carefully and gently.
1. Make sure the free end of the ground wire is outside of the
cabinet.
2. Insert air conditioner into cabinet.
to move and install
A
10
A
A. Make sure the free end of the ground wire is outside of the cabinet.
and 2-#9.5X
3/8”pan-head Phillips screws, attach front of panel
to chassis.
Starting Your Air Conditioner—Digital Control
Temperature
Money
Saver®
Auto Swing
Press, or press and hold, the plus button to raise the
temperature 1º until it reaches 90ºF (32.2ºC).
Timer
F
0
F
0
Temp/Hour
Temp/Hour
Hr.
POWER
Hr.
High
Cool
Mode
Med
Fan Speed
Low
Fan Only
Press, or press and hold, the minus button to lower the
temperature 1º until it reaches 60ºF (15.5ºC).
1. Press POWER to turn on air conditioner.
Timer Delay
To set the Timer for a 1- to 24-hour delay until the air
conditioner turns off (the air conditioner must be On):
POWER
1. Press TIMER. Indicator light will flash.
NOTE: When the unit is turned on, it will display the previous
settings for the Mode, Fan Speed and temperature.
Timer
2. Choose mode. See “Mode.”
3. Choose fan speed. See “Fan Speed.”
4. Choose temperature. See “Temperature.”
2. Press the plus or minus button to change the delay time from
1 to 24 hours.
3. Press TIMER or wait 10 seconds. Indicator light will remain
on.
Mode
1. Press and hold MODE.
2. Choose Cool or Fan mode
Cool—Cools room. Press FAN SPEED to choose fan
speed. Then adjust the temperature by pressing the up or
down arrow buttons.
To set the Timer delay for a 1- to 24-hour delay until the air
conditioner turns on, keeping previous settings:
1. Turn off air conditioner.
2. Press TIMER. Indicator light will flash.
3. Press the plus or minus button to change the delay time from
1 to 24 hours.
4. Press TIMER or wait 10 seconds. Indicator light will remain
on.
Fan—Operates the fan at High speed, without cool ing.
The display shows “FO” (fan only).
Money Saver®
To set the Timer delay for a 1- to 24-hour delay until the air
conditioner turns on, changing previous settings:
Money Saver — Cycles fan with compressor when
room temperature reaches the temperature setting
on the thermostat.
Cool
Mode
Fan Only
1.
2.
3.
4.
5.
6.
7.
Turn on air conditioner.
Adjust MODE to desired setting.
Adjust FAN SPEED to Low, Medium or High.
Adjust temperature between 60ºF (15.5ºC) and 90ºF (32.2ºC).
Turn off air conditioner.
Press TIMER. Indicator light will flash.
Press the plus or minus button to change delay time from 1 to
24 hours.
8. Press TIMER or wait 10 seconds.
Money
Saver®
Fan Speed
NOTE: The Fan Speed button will operate when the Cool,
Money Saver or Fan Only mode has been selected.
1. Press the Fan Speed button until you see the indicator light
for the desired setting.
2. Choose Low, Medium or High.
To clear Timer delay program
NOTE: Air conditioner can be either on or off.
Press TIMER. Indicator light will turn off.
High
Med
Fan Speed
Low
12
To raise the temperature:
To operate air conditioner with remote control
Press the plus button to raise the temperature. Each time you
press or hold the plus button, the temperature will go up 1º until it
reaches 90°F (32.2°C).
NOTE: Remote control may vary in appearance.
To lower the temperature:
Press the minus button to lower the temperature. Each time you
press or hold the minus button, the temperature will go down 1º
until it reaches 60°F (15.5°C).
To set Timer for a 1- to 24-hour delay before air conditioner
is turned off (air conditioner must be On):
1. Press TIMER. Indicator light on air conditioner control panel
will flash.
2. Press the plus or minus button to change the delay time from
1 to 24 hours.
3. Press TIMER again or wait 10 seconds. Indicator light on air
conditioner control panel will remain on.
NOTE: Two AAA batteries (included) power the remote control.
Replace batteries after 6 months of use, or when the remote
control starts to lose power.
To set Timer to turn on air conditioner, keeping previous
settings:
1. Turn off air conditioner.
2. Press TIMER. Indicator light on air conditioner control panel
will flash.
3. Press the plus or minus button to change delay time (1 to
24 hours).
4. Press TIMER again or wait 10 seconds. Indicator light on air
conditioner control panel will remain on.
To turn the air conditioner on or off:
Press POWER.
To select the mode:
Press COOL, FAN or $ SAVER
To set Timer to turn on air conditioner, changing the
previous settings:
1.
2.
3.
4.
5.
6.
Turn on air conditioner.
Adjust Mode to Cool, Fan Only, or Power Saver.
Adjust Fan Speed to High, Medium or Low.
Adjust temperature between 60°F (15.5ºC) and 90°F (32.2 ºC).
Turn off air conditioner.
Press TIMER. Indicator light on air conditioner control panel
will flash.
7. Press the plus or minus button to change delay time (1 to
24 hours).
8. Press TIMER again or wait 10 seconds. Indicator light on air
conditioner control panel will remain on.
To select the fan speed:
Press FAN SPEED for Low, Medium or High.
13
Air Conditioner Care
Your new air conditioner is designed to give you many years of
dependable service. This section tells you how to clean and care
for your air conditioner properly. Call your local authorized dealer
for an annual checkup. Remember… the cost of this service call
is your responsibility.
Cleaning the Front Panel
1. Turn off air conditioner.
2. Remove the air filter and clean it separately. See “Cleaning
the Air Filter.”
3. Wipe the front panel with a soft, damp cloth.
4. Air dry front panel comp letely.
Cleaning the Air Filter
The air filter is removable for easy cleaning. A clean filter helps
remove dust, lint, and other particles from the air and is important
for best cooling and operating efficiency. Check the filter every
2 weeks to see whether it needs cleaning.
NOTE: Do not operate the air conditioner without the filter in
place.
1. Turn off air conditioner.
2. Remove filter from unit.
Repairing Paint Damage
Check once or twice a year for paint damage. This is very
important, especially in areas near oceans or where rust is a
problem. If needed, touch up with a good grade enamel paint.
Annual Maintenance
3. Use a vacuum cleaner to clean air filter. If air filter is very dirty,
wash it in warm water with a mild detergent. Do not wash air
filter in the dishwasher or use any chemical cleaners. Air dry
filter completely before replacing to ensure maximum
efficiency.
4. Slide air filter down into the filter door. Close filter door.
Your air conditioner needs annual maintenance to help ensure
steady, top performance throughout the year. Call your local
authorized dealer to schedule an annual checkup. The expense
of an annual inspection is your responsibility.
Troubleshooting
Before calling for service, try the suggestions below to see whether you can solve your problem without outside help.
Air conditioner will not operate
Air conditioner blows fuses or trips circuit breakers
Too many appliances are being used on the same circuit.
Unplug or relocate appliances that share the same circuit.
Time-delay fuse or circuit breaker of the wrong capacity
is b eing used. Replace with a time-d elay fuse or circuit
breaker of the correct capacity. See “Electrical
Requirements.”
An extension cord is being used. Do not use an extension
cord with this or any other appliance.
You are trying to restart the air conditioner too soon after
turning the unit off. Wait at least 3 minutes after turning the
unit off before trying to restart the air conditioner.
.
Normal Sounds
When your air conditioner is operating normally, you may hear
sounds such as:
Droplets of water hitting the condenser, causing a pinging or
clicking sound. The water droplets help cool the condenser.
The power supply cord is unplugged. Plug into a grounded
3 prong outlet. See “Electrical Requirements.”
Air movement from the fan.
The power supply cord has tripped (Reset button has
popped out). Press and release RESET (listen for click; Reset
button will latch and remain in) to resume operation.
Clicks from the thermostat cycle.
Vibrations or noise due to poor wall or window cons truction.
A household fuse has blown, or a circuit breaker has
tripped. Replace the fuse or reset the circuit breaker. If the
problem continues, call an electrician. See “Electrical
Requirements.”
A high-pitched hum or pulsating noise caused by the modern
high-efficiency comp ressor cycling on and off.
Depending on model, the Power button has not been
pressed or the Fan control is turned to Off. Press POWER
or turn the Fan control to an active setting.
The local power has failed. Wait for power to be restored.
14
Air conditioner power supply cord trips (Reset button
pops out)
■
Disturbances in your electrical current can trip (Reset
button will pop out) the power supply cord. Press and
release RESET (listen for click; Reset button will latch and
remain in) to resume operation.
■
Electrical overloading, overheating, cord pinching or
aging can trip (Reset button will pop out) the power
supply cord. After correcting the problem, press and release
RESET (listen for click; Reset button will latch and remain in)
to resume operation.
NOTE: A damaged power supply cord must be replaced with a
new power supply cord obtained from the product manufacturer
and must not be repaired.
Air conditioner seems to run too much
■
The current air conditioner replaced an older model. The
use of more efficient components may cause the air
conditioner to run longer than an older model, but the total
energy consumption will be less. Newer air conditioners do
not emit the “blast” of cold air you may be accustomed to
from older units, but this is not an indication of lesser cooling
capacity or efficiency. Refer to the efficiency rating (EER) and
capacity rating (in BTU/hr.) marked on the air conditioner.
■
The air conditioner is in a heavily occupied room, or heatproducing appliances are in use in the room. Use exhaust
vent fans while cooking or bathing and try not to use heatproducing appliances during the hottest part of the day. A
higher capacity air conditioner may be required, depending
on the size of the room being cooled.
■
There is excessive heat or moisture (open container
cooking, showers, etc.) in the room. Use a fan to exhaust
heat or moisture from the room. Try not to use heatproducing appliances during the hottest part of the day.
■
The louvers are blocked. Install the air conditioner in a
location where the louvers are free from curtains, blinds,
furniture, etc.
■
The outside temperature is below 65°F (18°C). Do not try to
operate your air conditioner in the cooling mode when the
outside temperature is below 65°F (18°C).
■
The temperature of the room you are trying to cool is
extremely hot. Allow extra time for the air conditioner to cool
off a very hot room.
■
Windows or doors to the outside are open. Close all
windows and doors.
■
The Vent control is set to OPEN (on some models). Push
the Vent control to CLOSED for maximum cooling and/or
heating.
■
The temperature set point or Thermostat control is not at
a cool enough setting. Adjust the temperature set point to a
cooler setting by pressing the minus button to reduce the
temperature or adjust the Thermostat control to a cooler
setting by turning the knob clockwise. Turn the Fan control to
Turbo Cool.
■
The air contitioner in the heating mode has insufficient
BTU/hr for the heating requirements of the room. Do not
use the air conditioner as a primary source of heat.
Temperature on display does not match room
temperature
■
Air conditioner cycles on and off too much, or does not
cool/heat room in cooling/heating mode
When the compressor and fan motor turn off during
Power Saver mode, or after you turn off the unit, a lower
temperature reading than the actual room temperature
may be displayed for a short period of time. This lower
temperature reading is caused by the temperature sensor
being located close to the cold evaporator coil. The actual
room temperature will display within a few minutes.
■
The Mode or Fan control is set to Power Saver (on some
models). Use Power Saver only when you are asleep or away
from home, since the fan does not circulate the room air
continuously. Use Low Cool, Medium Cool or High Cool for
your best comfort.
■
The air conditioner is not properly sized for your room.
Check the cooling capabilities of your room air conditioner.
Room air conditioners are not designed to cool multiple
rooms.
■
The filter is dirty or obstructed by debris. Clean the filter.
The air conditioner is not properly leveled. The air
conditioner should slope slightly downward toward the
outside. Level the air conditioner to provide a downward
slope toward the outside to ensure proper drainage. See the
Installation Instructions.
■
The inside evaporator and outside condenser coils are
dirty or obstructed by debris. See “Annual Maintenance.”
NOTE: Do not drill a hole into the bottom of the metal base
and condensate pan.
Water drips from cabinet into your house
■
Assistance or Service
For further assistance
For assistance, service or replacement parts
If you need further assistance, you can write us at :
For service assistance or to locate factory-authorized parts,
call our Customer Service Center at 1-800-541-6645, or your
nearest authorized service center. You also can visit the "Dealer
Locator" at www.friedrich.com to locate your nearest authorized
Friedrich Service Center.
Friedrich Air Conditioning Co.
Customer Service
10001 Reunion Place, Suite 500
San Antonio, TX 78216
Or email: tac@friedrich.com
15
Please include a daytime phone number in your correspondence.
d
Friedrich Air Conditioning Company
10001 Reunion Place, Suite 500
78216
(800)541-6645
www.friedrich.com
ROOM AIR CONDITIONERS
LIMITED WARRANTY
FIRST YEAR
ANY PART: If any part supplied by FRIEDRICH fails because of a defect in workmanship or material within twelve months from
date of original purchase, FRIEDRICH will repair the product at no charge, provided room air conditioner is reasonably accessible
for service. Any additional labor cost for removing inaccessible units and/or charges for mileage related to travel by a Service
Agency that exceeds 25 miles one way will be the responsibility of the owner. This remedy is expressly agreed to be the exclusive
remedy within twelve months from the date of the original purchase.
SECOND THROUGH FIFTH YEAR
SEALED REFRIGERANT SYSTEM: If the Sealed Refrigeration System (defined for this purpose as the compressor, condenser coil,
evaporator coil, reversing valve, check valve, capillary, filter drier, and all interconnecting tubing) supplied by FRIEDRICH in your
Room Air Conditioner fails because of a defect in workmanship or material within sixty months from date of purchase, FRIEDRICH
will pay a labor allowance and parts necessary to repair the Sealed Refrigeration System; PROVIDED FRIEDRICH will not pay the
cost of diagnosis of the problem, removal, freight charges, and transportation of the air conditioner to and from the Service Agency,
and the reinstallation charges associated with repair of the Sealed Refrigeration System. All such cost will be the sole responsibility
of the owner. This remedy is expressly agreed to be the exclusive remedy within sixty months from the date of the original purchase.
APPLICABILITY AND LIMITATIONS: This warranty is applicable only to units retained within the Fifty States of the U.S.A., District
of Columbia, and Canada. This warranty is not applicable to:
1.
2.
3.
Air filters or fuses.
Products on which the model and serial numbers have been removed.
Products which have defects or damage which results from improper installation, wiring, electrical current
characteristics, or maintenance; or caused by accident, misuse or abuse, fire, flood, alterations and/or misapplication
of the product and/or units installed in a corrosive atmosphere, default or delay in performance caused by war,
government restrictions or restraints, strikes, material shortages beyond the control of FRIEDRICH, or acts of God.
OBTAINING WARRANTY PERFORMANCE: Service will be provided by the FRIEDRICH Authorized Dealer or Service
Organization in your area. They are listed in the Yellow Pages. If assistance is required in obtaining warranty performance, write to:
Room Air Conditioner Service Manager, Friedrich Air Conditioning Co., P.O. Box 1540, San Antonio, TX 78295-1540.
LIMITATIONS:
THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES. Anything in the warranty
notwithstanding, ANY IMPLIED WARRANTIES OF FITNESS FOR PARTICULAR PURPOSE AND/OR MERCHANTABILITY
SHALL BE LIMITED TO THE DURATION OF THIS EXPRESS WARRANTY. MANUFACTURER EXPRESSLY DISCLAIMS AND
EXCLUDES ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGE FOR BREACH OF ANY EXPRESSED OR
IMPLIED WARRANTY.
Performance of Friedrich’s Warranty obligation is limited to one of the following methods:
1. Repair of the unit
2. A refund to the customer for the prorated value of the unit based upon the remaining warranty period of the unit.
3. Providing a replacement unit of equal value
The method of fulfillment of the warranty obligation is at the sole discretion of Friedrich Air Conditioning.
NOTE: Some states do not allow limitations on how long an implied warranty lasts, or do not allow the limitation or exclusion of
consequential or incidental damages, so the foregoing exclusions and limitations may not apply to you.
OTHER: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
PROOF OF PURCHASE: Owner must provide proof of purchase in order to receive any warranty related services.
All service calls for explaining the operation of this product will be the sole responsibility of the consumer.
All warranty service must be provided by an Authorized FRIEDRICH Service Agency, unless authorized by FRIEDRICH prior to
repairs being made.
(10-08)
1-800-541-6645
66129903813
Download PDF

advertising