Friedrich US10C10 Air Conditioner User Manual

www.sylvane.com 1-800-934-9194
Uni- Fit
R
Thru-the-Wall Series
Service and Parts
Manual
Thru-the-Wall Series
115 Volts US08C10 US10C10 US12C10
230 Volts US10C30 US12C30 US14C30
Unifit Cool Svc Parts 2010 (05/10)
Unifit. Cool (03/07)
www.sylvane.com 1-800-934-9194
CONTENTS
2.4 REFRIGERATION CYCLE.................................14
2.4.1 CONDENSER ......................................14
2.4.2 EVAPORATOR ....................................14
2.4.3 CAPILLARY TUBE...............................14
1. PREFACE
1.1 SAFETY PRECAUTIONS ...............................2
1.2 INSULATION RESISTANCE TEST.................2
1.3 SPECIFICATIONS ..........................................3~8
1.4 FEATURES .....................................................9
1.5 CONTROL LOCATIONS .................................9
3. TROUBLESHOOTING GUIDE
3.1 OUTSIDE DIMENSIONS...............................17
3.2 PIPING SYSTEM ..........................................17
3.3 TROUBLESHOOTING GUIDE......................18
2. DISASSEMBLY INSTRUCTIONS
2.1 MECHANICAL PARTS....................................10
2.1.1 FRONT GRILLE .....................................10
2.1.2 CABINET................................................10
2.1.3 CONTROL BOX .....................................10
2.2 AIR HANDLING PARTS..................................11
2.2.1 ORIFICE, HEATER ASSY AND TURBO FAN .........11
4. SCHEMATIC DIAGRAM
4.1 CIRCUIT DIAGRAM ......................................23
5. EXPLODED VIEW ..................................24
6. REPLACEMENT PARTS LIST .......25~30
2.2.2 FAN ........................................................11
2.2.3 SHROUD................................................12
2.3 ELECTRICAL PARTS .....................................12
2.3.1 MOTOR..................................................12
2.3.2 COMPRESSOR .....................................12
2.3.3 CAPACITOR ..........................................12
2.3.4 POWER CORD ......................................13
2.3.5 THERMISTOR .......................................13
1. PREFACE
This SERVICE MANUAL provides various service information, including the mechanical and electrical
parts etc. This room air conditioner was manufactured and assembled under a strict quality control system.
The refrigerant is charged at the factory. Be sure to read the safety precautions prior to servicing the unit.
1.1 SAFETY PRECAUTIONS
1.2 INSULATION RESISTANCE TEST
1. When servicing the unit, turn off the air conditioner
and unplug the power cord.
2. Observe the original lead dress.
If a short circuit is found, replace all parts which
have been overheated or damaged by the short
circuit.
3. After servicing the unit, make an insulation
resistance test to protect the customer from being
exposed to shock hazards.
1. Unplug the power cord and connect a jumper
between 2 pins (black and white).
2. The grounding conductor (green or green & yellow)
is to be open.
3. Measure the resistance value with an ohm meter
between the jumpered lead and each exposed
metallic part on the equipment.
4. The value should be over 1MΩ.
—2—
www.sylvane.com 1-800-934-9194
1.3 SPECIFICATIONS
MODELS
US08C10
ITEMS
POWER SUPPLY
REMARK
1Ø, 115V, 60Hz
COOLING CAPACITY (Btu/h)
INPUT
8,000
(W)
830
RUNNING CURRENT (A)
7.5
E.E.R
9.6
(Btu/w.h)
REFRIGERANT (R410A) CHARGE
400g(14.1OZ)
OPERATING
INDOOR (°F)
80(DB) 67(WB)
TEMPERATURE
OUTDOOR (°F)
95(DB) 75(WB)
EVAPORATOR
2 ROW 12STACKS
Ø5 2ROW 18STACKS, L-BENDING TYPE
CONDENSER
FAN, INDOOR
LOUVERED-FIN TYPE
TURBO FAN
FAN, OUTDOOR
PROPELLER TYPE FAN WITH SLINGER-RING
FAN SPEEDS, FAN/COOLING
3/3
6 POLES
FAN MOTOR
OPERATION CONTROL
ELECTRIC
ROOM TEMP. CONTROL
THERMISTOR
VERTICAL LOUVER(RIGHT & LEFT)
AIR DIRECTION CONTROL
HORIZONTAL LOUVER(UP & DOWN)
TOP-DOWN
CONSTRUCTION
PROTECTOR
COMPRESSOR
FAN MOTOR
EXTERNAL OVERLOAD PROTECTOR
INTERNAL THERMAL PROTECTOR
3WIRES WITH GROUNDING
POWER CORD
ATTACHMENT PLUG(CORD-CONNECTED TYPE, LCDI)
SPLASHED BY FAN SLINGER
DRAIN SYSTEM
NET WEIGHT
73/33
(lbs/kg)
DIMENSION
(inch)
24 x 1413/32 x 20 3/32
(W x H x D)
(mm)
610 x 366 x 499
SLEEVE DIMESION
(inch)
25 7/8 x 15 17/32 x 16 23/32
(W x H x D)
(mm)
656 x 394 x 425
SLEEVE DEPTH
(inch)
20 1/2
WITH FRONT GRILLE
(mm)
521
—3—
OPTIONAL
PART
www.sylvane.com 1-800-934-9194
1.3 SPECIFICATIONS
MODELS
US10C10
ITEMS
POWER SUPPLY
REMARK
1Ø, 115V, 60Hz
COOLING CAPACITY (Btu/h)
INPUT
9,800
(W)
1,040
RUNNING CURRENT (A)
9.6
E.E.R
9.4
(Btu/w.h)
REFRIGERANT (R-410A) CHARGE
445g(15.7OZ)
OPERATING
INDOOR (°F)
80 (DB) 67(WB)
TEMPERATURE
OUTDOOR (°F)
95(DB) 75 (WB)
EVAPORATOR
2 ROW 12STACKS
Ø5 .0 3ROW 18STACKS, L-BENDING TYPE
CONDENSER
FAN, INDOOR
LOUVERED-FIN TYPE
TURBO FAN
FAN, OUTDOOR
PROPELLER TYPE FAN WITH SLINGER-RING
FAN SPEEDS, FAN/COOLING
3/3
FAN MOTOR
6 POLES
OPERATION CONTROL
ELECTRIC
ROOM TEMP. CONTROL
THERMISTOR
VERTICAL LOUVER(RIGHT & LEFT)
AIR DIRECTION CONTROL
HORIZONTAL LOUVER(UP & DOWN)
TOP-DOWN
CONSTRUCTION
PROTECTOR
COMPRESSOR
FAN MOTOR
EXTERNAL OVERLOAD PROTECTOR
INTERNAL THERMAL PROTECTOR
3WIRES WITH GROUNDING
POWER CORD
ATTACHMENT PLUG(CORD-CONNECTED TYPE, LCDI)
SPLASHED BY FAN SLINGER
DRAIN SYSTEM
NET WEIGHT
73/33
(lbs/kg)
DIMENSION
(inch)
24 x 1413/32 x 20 3/32
(W x H x D)
(mm)
610 x 366 x 499
SLEEVE DIMESION
(inch)
25 7/8 x 15 17/32 x 16 23/32
(W x H x D)
(mm)
656 x 394 x 425
SLEEVE DEPTH
(inch)
20 1/2
WITH FRONT GRILLE
(mm)
521
—4—
OPTIONAL
PART
www.sylvane.com 1-800-934-9194
MODELS
US10C30
ITEMS
REMARK
1Ø, 230V/208V, 60Hz
POWER SUPPLY
10,000/9,800
COOLING CAPACITY (Btu/h)
INPUT
(W)
1060/1040
RUNNING CURRENT (A)
4.7/5.2
E.E.R
9.4/9.4
(Btu/w.h)
REFRIGERANT (R410A) CHARGE
460g(16.2 OZ)
OPERATING
INDOOR (°F)
80(DB) 67(WB)
TEMPERATURE
OUTDOOR (°F)
95(DB) 75(WB)
2 ROW 12STACKS
EVAPORATOR
Ø 5.0 3ROW 18STACKS, L-BENDING TYPE
CONDENSER
FAN, INDOOR
LOUVERED-FIN TYPE
TURBO FAN
FAN, OUTDOOR
PROPELLER TYPE FAN WITH SLINGER-RING
FAN SPEEDS, FAN/COOLING
3/3
FAN MOTOR
6 POLES
OPERATION CONTROL
ELECTRIC
ROOM TEMP. CONTROL
THERMISTOR
VERTICAL LOUVER(RIGHT & LEFT)
AIR DIRECTION CONTROL
HORIZONTAL LOUVER(UP & DOWN)
TOP-DOWN
CONSTRUCTION
PROTECTOR
COMPRESSOR
FAN MOTOR
EXTERNAL OVERLOAD PROTECTOR
INTERNAL THERMAL PROTECTOR
3WIRES WITH GROUNDING
POWER CORD
ATTACHMENT PLUG(CORD-CONNECTED TYPE, LCDI)
SPLASHED BY FAN SLINGER
DRAIN SYSTEM
NET WEIGHT
73/33
(lbs/kg)
DIMENSION
(inch)
24 x 1413/32 x 20 3/32
(W x H x D)
(mm)
610 x 366 x 499
SLEEVE DIMESION
(inch)
25 7/8 x 15 17/32 x 16 23/32
(W x H x D)
(mm)
656 x 394 x 425
SLEEVE DEPTH
(inch)
20 1/2
WITH FRONT GRILLE
(mm)
521
—5—
OPTIONAL
PART
www.sylvane.com 1-800-934-9194
MODELS
US12C10
ITEMS
POWER SUPPLY
1Ø, 230V/208V, 60Hz
COOLING CAPACITY (Btu/h)
11500/11200
INPUT
(W)
REMARK
1220/1190
RUNNING CURRENT (A)
5.6/6.0
E.E.R
9.4/9.4
(Btu/w.h)
REFRIGERANT (R-410A) CHARGE
525g(18.0 OZ)
OPERATING
INDOOR (°F)
80(DB) 67(WB)
TEMPERATURE
OUTDOOR (°F)
95(DB) 75(WB)
EVAPORATOR
2 ROW 12STACKS
CONDENSER
3ROW 18STACKS, L-BENDING TYPE, 1 ROW
FAN, INDOOR
LOUVERED-FIN TYPE
TURBO FAN
FAN, OUTDOOR
PROPELLER TYPE FAN WITH SLINGER-RING
FAN SPEEDS, FAN/COOLING
3/3
6 POLES
FAN MOTOR
OPERATION CONTROL
ELECTRIC
ROOM TEMP. CONTROL
THERMISTOR
VERTICAL LOUVER(RIGHT & LEFT)
AIR DIRECTION CONTROL
HORIZONTAL LOUVER(UP & DOWN)
TOP-DOWN
CONSTRUCTION
PROTECTOR
COMPRESSOR
FAN MOTOR
EXTERNAL OVERLOAD PROTECTOR
INTERNAL THERMAL PROTECTOR
3WIRES WITH GROUNDING
POWER CORD
ATTACHMENT PLUG(CORD-CONNECTED TYPE, LCDI)
SPLASHED BY FAN SLINGER
DRAIN SYSTEM
NET WEIGHT
73/33
(lbs/kg)
DIMENSION
(inch)
24 x 1413/32 x 20 3/32
(W x H x D)
(mm)
610 x 366 x 499
SLEEVE DIMESION
(inch)
25 7/8 x 15 17/32 x 16 23/32
(W x H x D)
(mm)
656 x 394 x 425
SLEEVE DEPTH
(inch)
20 1/2
WITH FRONT GRILLE
(mm)
521
—6—
OPTIONAL
PART
www.sylvane.com 1-800-934-9194
MODELS
US12C30
ITEMS
POWER SUPPLY
REMARK
1Ø, 230/208V, 60Hz
COOLING CAPACITY (Btu/h)
INPUT
11,500/11,200
(W)
1,220/1,190
RUNNING CURRENT (A)
5.6/6.0
E.E.R
9.4/9.4
(Btu/w.h)
510g(18.0OZ)
REFRIGERANT (R-410A) CHARGE
OPERATING
INDOOR (°F)
80(DB) 67(WB)
TEMPERATURE
OUTDOOR (°F)
95(DB) 75(WB)
2 ROW 12STACKS
EVAPORATOR
CONDENSER
3ROW 18STACKS, L-BENDING TYPE 1 ROW
FAN, INDOOR
LOUVERED-FIN TYPE
TURBO FAN
FAN, OUTDOOR
PROPELLER TYPE FAN WITH SLINGER-RING
FAN SPEEDS, FAN/COOLING
3/3
6 POLES
FAN MOTOR
OPERATION CONTROL
ELECTRIC
ROOM TEMP. CONTROL
THERMISTOR
AIR DIRECTION CONTROL
VERTICAL LOUVER(RIGHT & LEFT)
HORIZONTAL LOUVER(UP & DOWN)
CONSTRUCTION
PROTECTOR
TOP-DOWN
COMPRESSOR
FAN MOTOR
POWER CORD
EXTERNAL OVERLOAD PROTECTOR
INTERNAL THERMAL PROTECTOR
3WIRES WITH GROUNDING
ATTACHMENT PLUG(CORD-CONNECTED TYPE, LCDI)
DRAIN SYSTEM
NET WEIGHT
SPLASHED BY FAN SLINGER
(lbs/kg)
73/33
DIMENSION
(inch)
24 x 1413/32 x 20 3/32
(W x H x D)
(mm)
610 x 366 x 499
SLEEVE DIMESION
(inch)
25 7/8 x 15 17/32 x 16 23/32
(W x H x D)
(mm)
656 x 394 x 425
SLEEVE DEPTH
(inch)
20 1/2
WITH FRONT GRILLE
(mm)
521
—7—
OPTIONAL
PART
www.sylvane.com 1-800-934-9194
MODELS
US14C30
ITEMS
POWER SUPPLY
1Ø, 230/208V, 60Hz
COOLING CAPACITY (Btu/h)
13,000/12,600
INPUT
(W)
REMARK
1,530/1,480
RUNNING CURRENT (A)
7.0/7.5
E.E.R
8.5/8.5
(Btu/w.h)
510g(18.0OZ)
REFRIGERANT (R-410A) CHARGE
OPERATING
INDOOR (°F)
80(DB) 67(WB)
TEMPERATURE
OUTDOOR (°F)
95(DB) 75(WB)
2 ROW 12STACKS
EVAPORATOR
CONDENSER
3ROW 18STACKS, L-BENDING TYPE,1ROW
FAN, INDOOR
LOUVERED-FIN TYPE
TURBO FAN
FAN, OUTDOOR
PROPELLER TYPE FAN WITH SLINGER-RING
FAN SPEEDS, FAN/COOLING
3/3
6 POLES
FAN MOTOR
OPERATION CONTROL
ELECTRIC
ROOM TEMP. CONTROL
THERMISTOR
AIR DIRECTION CONTROL
VERTICAL LOUVER(RIGHT & LEFT)
HORIZONTAL LOUVER(UP & DOWN)
CONSTRUCTION
PROTECTOR
TOP-DOWN
COMPRESSOR
FAN MOTOR
POWER CORD
EXTERNAL OVERLOAD PROTECTOR
INTERNAL THERMAL PROTECTOR
3WIRES WITH GROUNDING
ATTACHMENT PLUG(CORD-CONNECTED TYPE, LCDI)
DRAIN SYSTEM
NET WEIGHT
SPLASHED BY FAN SLINGER
(lbs/kg)
73/33
DIMENSION
(inch)
24 x 1413/32 x 20 3/32
(W x H x D)
(mm)
610 x 366 x 499
SLEEVE DIMESION
(inch)
25 7/8 x 15 17/32 x 16 23/32
(W x H x D)
(mm)
656 x 394 x 425
SLEEVE DEPTH
(inch)
20 1/2
WITH FRONT GRILLE
(mm)
521
—8—
OPTIONAL
PART
www.sylvane.com 1-800-934-9194
1.4 FEATURES
• Designed for cooling only.
• Built in adjustable THERMOSTAT.
• Powerful and quiet.
• Slide out chassis for the simple installation and service.
• Washable one-touch filter.
• Compact size.
1.5 CONTROL LOCATIONS
1.5.1 COOLING ONLY MODEL
• OPERATION
• VENTILATION
Push the lever to the "CLOSE" position to cool, heat or recirculate room air only.
Pull the lever to the "OPEN" position to exhaust smoke or stale air from the room.
This feature is best used in conjunction with the FAN ONLY position.
CAUTION
When the air conditioner has been operating in the
cooling and is turned off or set to the fan only position,
wait at least 3 minutes before resetting to the cooling
operation again.
PULL OPEN / PUSH CLOSE
—9—
www.sylvane.com 1-800-934-9194
2. DISASSEMBLY INSTRUCTIONS
— Prior to disassembling the unit, make sure that the POWER is off and the power cord is unplugged from the
wall receptacle.
2.1 MECHANICAL PARTS
2.1.1 FRONT GRILLE
1. Open the inlet grille downward.
2. Remove the screw which fastens the front grille.
3. Pull the front grille from the right side.
4. Remove the front grille. (See Fig. 1)
5. Re-install the component by referring to the
removal procedure.
Figure 1
2.1.2 CABINET
1. After disassembling the FRONT GRILLE, remove
the 6 screws which fasten the cabinet at the both
sides and the top. (See Fig. 2)
Keep these for later use.
Figure 2
2.1.3 CONTROL BOX
1. Remove the front grille. (Refer to section 2.1.1)
2. Remove the screw which fasten the control
box. (See Fig. 3)
3. Pull the control box from the barrier.(See Fig.3)
4. Discharge the capacitor by placing a 20,000 ohm
resistor across the capacitor terminals.
5. Disconnect two wire housings in the control box.
6. Pull the control box forward completely.
7. Re-install the components by referring to the
removal procedure. (See Fig. 3)
(Refer to the circuit diagram found on page 19 in
this manual and on the control box.)
Figure 3
—10—
www.sylvane.com 1-800-934-9194
2.2 AIR HANDLING PARTS
2.2.1 ORIFICE, AND TURBO FAN
1. Remove the front grille. (Refer to section 2.1.1)
2. Remove the cabinet. (Refer to section 2.1.2)
3. Remove the 2 screws which fasten the
evaporator at the left side and the right side.
(See Fig. 4)
4. Move the evaporator to the side carefully.
Figure 4
5. Remove the orifice. (See Fig. 5)
Figure 5
8. Using handheld pliers, remove the clamp which
secures the turbo fan. (See Fig. 6)
Figure 6
9. Remove the turbo fan with pliers or your hand,
without touching blades. (See Fig. 7)
10. Re-install the components by referring to the
removal procedures, above.
Figure 7
2.2.2 FAN
1. Remove the cabinet. (Refer to section 2.1.2)
2. Remove the brace.
(Refer to section 2.2.1)
3. Remove the 7 screws which fasten the condenser.
4. Move the condenser to the side carefully.
5. Using handheld pliers, remove the clamp which
secures the fan.
6. Remove the fan. (See Fig. 8)
7. Re-install the components by referring to the
removal procedures, above.
Figure 8
—11—
www.sylvane.com 1-800-934-9194
2.2.3 SHROUD
1. Remove the fan. (Refer to section 2.2.2)
2. Remove the shroud. (See Fig. 9)
3. Re-install the components by referring to the
removal procedures, above.
2.3 ELECTRICAL PARTS
2.3.1 MOTOR
1. Remove the cabinet. (Refer to section 2.1.2)
2. Remove the clamp cord and disconnect the wire
housing in control box. (Refer to section 2.1.3)
3. Remove the turbo fan. (Refer to section 2.2.2)
4. Remove the fan. (Refer to section 2.2.2)
5. Remove the 4 or 2 screws which fasten the motor.
(See Fig. 10)
6. Remove the motor.
7. Re-install the components by referring to the
removal procedures, above.
Figure 9
2.3.2 COMPRESSOR
1. Remove the cabinet. (Refer to section 2.1.2)
2. Discharge the refrigerant system using a FreonTM
Recovery System.
Install a valve for recovery before venting the
Freon. Remove the valve when finished.
3. Disconnect the 3 leads from the compressor.
4. After purging the unit completely, unbraze the
suction and discharge tubes at the compressor
connections.
5. Remove the 3 nuts and the 3 washers which
fasten the compressor. (See Fig. 11)
6. Remove the compressor.
7. Re-install the components by referring to the
removal procedures, above.
Figure 10
2.3.3 CAPACITOR
Figure 11
1. Remove the control box. (Refer to section 2.1.3)
2. Remove the 1 screw
3. Open the control box
4. Disconnect all the leads on the capacitor terminals.
5. Re-install the components by referring to the
removal procedures, above.
Figure 12
—12—
www.sylvane.com 1-800-934-9194
2.3.4 POWER CORD
1. Remove the control box. (Refer to section 2.1.3)
2. Unfold the control box. (Refer to section 2.3.3)
3. Disconnect the grounding screw from the Base
pan.
4. Disconnect 2 receptacles.
5. Remove a screw which fastens the clip cord.
6. Pull the power cord. (See Fig. 13)
7. Re-install the components by referring to the
removal procedure, above.
(Use only one ground-marked hole, , for ground
connection.)
8. If the supply cord of this appliance is damaged, it
must be replaced with the factory-authorized and
specified cord.
Figure 13
2.3.5 ELECTRONIC CONTROL BOARD
1. Remove the control box. (Refer to section 2.1.3)
2. Unfold the control box. (Refer to section 2.3.3)
3. Disconnect all the leads of Electronic control board
terminals.
4. Remove the Electronic control board. (See Fig. 14)
5. Re-install the components by referring to the
removal procedures, above.
Figure 14
—13—
www.sylvane.com 1-800-934-9194
2.4 REFRIGERATION CYCLE
CAUTION
Discharge the refrigerant system using a FreonTM
Recovery System.
Install a valve for the recovery, before venting
the Freon, remove the valve when finished.
2.4.1 CONDENSER
1. Remove the cabinet. (Refer to section 2.1.2)
2. Remove the brace.
(Refer to section 2.2.1)
3. Remove the 7 screws which fasten the condenser.
4. After discharging the refrigerant completely into a
FreonTM Recovery System, unbraze the
interconnecting tube at the condenser
connections.
5. Remove the condenser.
6. Re-install the components by referring to the notes
– on pages 11-13. (See Fig. 15)
Figure 15
2.4.2 EVAPORATOR
1. Remove the cabinet. (Refer to section 2.1.2)
2. Discharge the refrigerant completely – into a
FreonTM Recovery System.
3. Remove the 2 screws which fasten the evaporator
at the left side and the right side.
4. Move the evaporator to the side carefully and then
unbraze the interconnecting tube at the evaporator
connectors.
5. Remove the evaporator.
6. Re-install the components by referring to the notes
– on pages 11-13. (See Fig. 16)
Figure 16
2.4.3 CAPILLARY TUBE
1. Remove the cabinet. (Refer to section 2.1.2)
2. After discharging the refrigerant completely – into
a FreonTM Recovery System, unbraze the
interconnecting tube at the capillary tube.
3. Remove the capillary tube.
4. Re-install the components by referring to the notes
– on page 11-13.
—14—
www.sylvane.com 1-800-934-9194
NOTES
— Replacement of the refrigeration cycle.
1. When replacing refrigeration components, be sure
to discharge the refrigerant system using a FreonTM
recovery System.
Install a valve for the recovery, before venting the
Freon, remove the valve when finished.
2. After discharging the unit completely, remove the
desired component, and unbraze the pinch-off
tubes.
3. Solder service valves into the pinch-off tube ports,
leaving the valves open.
4. Solder the pinch-off tubes with Service valves.
5. Evacuate as follows.
1) Connect the vacuum pump, as illustrated Fig.
17A.
2) Start the vacuum pump, slowly open manifold
valves A and B with two full turns
counterclockwise and leave the valves closed.
The vacuum pump is now pulling through valves
A and B up to valve C by means of the manifold
and entire system.
CAUTION
If high vacuum equipment is used, just crack
valves A and B for a few minutes, then open
slowly with the two full turns counterclockwise.
This will keep oil from foaming and being
drawn into the vacuum pump.
3) Operate the vacuum pump for 20 to 30 minutes,
until 600 microns of vacuum is obtained. Close
valves A and B, and observe vacuum gauge for
a few minutes. A rise in pressure would
indicate a possible leak or moisture remaining in
the system. With valves A and B closed, stop
the vacuum pump.
4) Remove the hose from the vacuum pump and
place it on the charging cylinder. See Fig. 17B.
Open valve C.
Discharge the line at the manifold connection.
5) The system is now ready for final charging.
6. Recharge as follows :
1) Refrigeration cycle systems are charged from the
High-side. If the total charge cannot be put
in the High-side, the balance will be put in the
suction line through the access valve which you
installed as the system was opened.
2) Connect the charging cylinder as shown in Fig. 17B.
With valve C open, discharge the hose at the
manifold connection.
3) Open valve A and allow the proper charge to
enter the system. Valve B is still closed.
4) If more charge is required, and the high-side will
not
take it. Close valve A.
5) With the unit running, open valve B and add the
balance of the charge.
a. Do not add the liquid refrigerant to the Lowside.
b. Watch the Low-side gauge; allow pressure to
rise to 39 lbs.
c. Turn off valve B and allow pressure to drop.
d. Repeat steps B and C until the balance of the
charge is in the system.
6) When satisfied the unit is operating correctly,
use the pinch-off tool with the unit still running
and clamp on to the pinch-off tube. Using a tube
cutter, cut the pinch-off tube about 2 inches from
the pinch-off tool. Use sil-fos solder and solder
pinch-off tube closed. Turn off the unit, allow it to
set for a while, and then test for leakage add the
pinch-off connection.
—15—
www.sylvane.com 1-800-934-9194
Equipment needed: Vacuum pump, Charging cylinder, Manifold gauge, Brazing equipment, Pinch-off tool
capable of making a vapor-proof seal, Leak detector, Tubing cutter, Hand Tools to remove components, Service
valve.
COMPOUND GAUGE
CONDENSER
(HIGH PRESSURE SIDE)
MANIFOLD
GAUGE
A
B
CAPILLARY TUBE
SEE INSETS
BELOW
EVAPORATOR
(LOW PRESSURE SIDE)
COMPRESSOR
LOW
HI
A
B
B
A
EXTERNAL
VACUUM PUMP
CHARGING
CYLINDER
C
Figure 17A-Pulling Vacuum
Figure 17B-Charging
—16—
www.sylvane.com 1-800-934-9194
3. TROUBLESHOOTING GUIDE
3.1 OUTSIDE DIMENSIONS
20-3/32"
(499mm)
14-3/8"
(366mm)
24"
(610mm)
3.2 PIPING SYSTEM
CONDENSER COILS
FAN
CAPILLARY TUBE
MOTOR
COMPRESSOR
TURBO FAN
EVAPORATOR COILS
: REFRIGERANT FLOW
Following is a brief description of the important components and their functions in the refrigeration system.
Refer to Fig. 18 to follow the refrigeration cycle and the flow of the refrigerant in the cooling cycle.
ROOM AIR CONDITIONER
CYCLE OF REFRIGERATION
EVAPORATOR COILS
CONDENSER COILS
COMPLETE LIQUID
BOIL OFF POINT
COOLED
AIR
SUCTION LINE
COOL LOW PRESSURE VAPOR
VAPOR INLET
HOT
DISCHARGED
AIR
ROOM AIR HEAT LOAD
MOTOR
OUTSIDE COOLING
AIR FOR REFRIGERANT
PASS THROUGH
COMPRESSOR
OIL
LIQUID
PRESSURE
DROP
LIQUID OUTLET
(LIQUID REFRIGERANT)
HIGH PRESSURE VAPOR
LIQUID REFRIGERANT
CAPILLARY TUBE
Figure 18
—17—
LOW PRESSURE VAPOR
www.sylvane.com 1-800-934-9194
3.3 TROUBLESHOOTING GUIDE
In general, possible trouble is classified in two causes.
One is called Starting Failure which is caused from an electrical defect, and the other is Ineffective Air Conditioning
caused by a defect in the refrigeration circuit and/or improper application.
Unit is running but cooling is ineffective
Ineffective Cooling
Check cold air circulation
for smooth flow.
Check outdoor coil
(heat exchanger) & the fan
operation.
Dirty indoor coil
(Heat exchanger)
Check gas leakage.
Malfunction of fan
Repair gas leak.
Clogged air filter
Replacement of unit if the
unit is beyond repair.
Check heat load increase.
Unexpected residue
Overloaded Circuit
Check inside gas pressure.
Obstruction at air outlet
Adjusting of refrigerant
charge
Correct above troubles
Malfunction of compressor
Check for a clog in
refrigeration circuit.
Repair for a clog in
refrigeration circuit.
Satisfactory operation with
temperature difference of
inlet & outlet air ; 18-26°F
—18—
Replacement of
compressor
www.sylvane.com 1-800-934-9194
Fails to Start
Check power source.
Check circuit breaker
and fuse.
Check control switch
setting.
Check control board
Only compressor fails to
start.
Only fan fails to start.
Improper wiring.
Drop in power voltage.
Improper thermostat setting
Defect of fan motor
capacitor.
Defective compressor
capacitor.
Loose terminal connection.
Check capacitor.
Irregular motor resistance
( ).
Irregular motor insulation
( ).
Improper wiring
Replacement.
Replacement of fan motor
Irregular motor resistance ( )
Regular but fails to start
Irregular motor insulation ( )
Replacement of compressor
(locking of rotor, metal)
Replacement of compressor
(Motor damaged)
—19—
www.sylvane.com 1-800-934-9194
COMPLAINT
Fan motor will not run.
CAUSE
REMEDY
No power
Check voltage at outlet. Correct if none.
Wire disconnected or
connection loose
Connect wire. Refer to wiring diagram for terminal
identification. Repair or replace loose terminal.
Capacitor (Discharge
capacitor before testing.)
Test capacitor.
Replace if not within ±10% of manufacturer's
rating. Replace if shorted, open, or damaged.
Will not rotate
Fan blade hitting shroud or blower wheel hitting
scroll. Realign assembly.
Units using slinger ring condenser fans must
have 1/4 to 5/16 inch clearance to the base. If it is
hitting the base, shim up the bottom of the fan
motor with mounting screw(s).
Check fan motor bearings; if motor shaft will not
rotate, replace the motor.
Fan motor runs
intermittently
Cycles on overload.
Check voltage. See limits on page 17. If not within
limits, call an electrician.
Test capacitor.
Check bearings. Does the fan blade rotate freely?
If not, replace fan motor.
Pay attention to any change from high speed to
low speed. If the speed does not change, replace
the motor.
Fan motor noise.
Grommets
Check grommets; if worn or missing, replace them.
Fan
If cracked, out of balance, or partially missing,
replace it.
Turbo fan
If cracked, out of balance, or partially missing,
replace it.
Loose set screw
Tighten it.
Worn bearings
If knocking sounds continue when running or
loose, replace the motor. If the motor hums or
noise appears to be internal while running,
replace motor.
—20—
www.sylvane.com 1-800-934-9194
COMPLAINT
Compressor will not run,
but fan motor runs.
CAUSE
REMEDY
Voltage
Check voltage. See the limits on the preceding.
page. If not within limits, call an electrician.
Wiring
Check the wire connections, if loose, repair or
replace the terminal. If wires are off, refer to wiring
diagram for identification, and replace. Check wire
locations. If not per wiring diagram, correct.
Capacitor (Discharge
capacitor before
servicing.)
Check the capacitor.
Replace if not within ±10% of manufacturers
rating. Replace if shorted, open, or damaged.
Compressor
Check the compressor for open circuit or
ground. If open or grounded, replace the
compressor.
Check the compressor overload, if externally
mounted. Replace if open. (If the compressor
temperature is high, remove the overload, cool it,
and retest.)
Overload
ROOM AIR CONDITIONER VOLTAGE LIMITS
NAME PLATE RATING
MINIMUM
MAXIMUM
115V
103.5V
126.5V
208/230V
187V
253V
—21—
www.sylvane.com 1-800-934-9194
COMPLAINT
Compressor cycles
on overload.
Insufficient cooling or
heating
Excessive noise.
REMEDY
CAUSE
Voltage
Check the voltage. See the limits on the preceding page. If not within limits, call an electrician.
Overload
Check overload, if externally mounted.
Replace if open. (If the compressor temperature
is high, remove the overload, cool, and retest.)
Fan motor
If not running, determine the cause. Replace if
required.
Condenser air flow
restriction
Remove the cabinet. Inspect the interior surface
of the condenser; if restricted, clean carefully
(do not damage fins). Clean the interior base before
reassembling.
Condenser fins
(damaged)
If condenser fins are closed over a large area
on the coil surface, head pressures will increase,
causing the compressor to cycle. Straighten the
fins or replace the coil.
Test capacitor.
Check the terminals. If loose, repair or replace.
Check the system for a restriction.
If restricted, clean or replace.
Close if open.
Determine if the unit is properly sized for the area to
be cooled.
Check the set screw or clamp. If loose or missing,
correct. If the blower or fan is hitting air guide,
rearrange the air handling parts.
Remove the cabinet and carefully rearrange tubing
not to contact cabinet, compressor, shroud, and
barrier.
Capacitor
Wiring
Refrigerating system
Air filter
Exhaust damper door
Unit undersized
Blower or fan
Copper tubing
—22—
www.sylvane.com 1-800-934-9194
4. SCHEMATIC DIAGRAM
4.1 CIRCUIT DIAGRAM
WIRING DIAGRAM
(SMPS)
250V/T2A
(250V/T3.15A)
MEZ62420710
—23—
www.sylvane.com 1-800-934-9194
Exploded View
Exploded View
C
152302
147581
132100
147582-1
135303
147582-2
131400
149980
135312
359012
W48602
559011
346811
349480
435300
352380
435301
731273
267110
130410
A
264110
268711-2
249950
B
567480
567502
268711-1
Co
ol
En
e
Savrg y
er
Fa
n
MO
DE
Ti m
F1
F2 LOW
F3 MED
HIG
H
er
TE
TIM
ER
W0CZZ
'F
MP
F
SP A N
EE
D
PO
WE
R
238310
550140
237200
—24—
www.sylvane.com 1-800-934-9194
LocNo
Description
US08C10
W0CZZ
CAPACITOR,FILM,BOX
67300709
130410
BASE ASSEMBLY,SINGLE
67302925
130900
CABINET
67303717
132100
FRAME
67308102
135303
GRILLE,INLET
67306106
135312
GRILLE ASSEMBLY,FRONT(SINGLE)
67306012
238310
ESCUTCHEON
67500114
W48602
CLAMP,SPRING
67302500
346811
MOTOR ASSEMBLY,SINGLE
67303021
147581
LOUVER,HORIZONTAL
67306205
147582-1
LOUVER,VERTICAL
67306256
147582-2
LOUVER,VERTICAL
67306257
149980
SHROUD
67500112
550140
DAMPER,COMPRESSOR
67305000
152302
FILTER,AIR
67500113
352380
AIR GUIDE
67302739
359012
FAN,TURBO
67302607
559011
FAN ASSEMBLY,AXIAL
67303202
567480
THERMISTOR ASSEMBLY
67307804
264110
POWER CORD ASSEMBLY
67300027
267110
REMOTE CONTROLLER ASSEMBLY
67302239
567502
OverloadProtect
67301907
268711-2
PWB(PCB) ASSEMBLY,MAIN
67307620
268711-1
PWB(PCB) ASSEMBLY,DISPLAY
67307619
435300
GRILLE,REAR
67304801
237200
PANEL,CONTROL
67305510
731273
INSTALL PART ASSEMBLY,SINGLE
67306311
249950
CASE ASSEMBLY,CONTROL
67305521
435301
GRILLE,REAR
67304801
349480
ORIFICE
67303409
—25—
www.sylvane.com 1-800-934-9194
LocNo
Description
US10C10
W0CZZ
CAPACITOR,FILM,BOX
67300724
130410
BASE ASSEMBLY,SINGLE
67305520
130900
CABINET
67303717
132100
FRAME
67308102
135303
GRILLE,INLET
67306106
135312
GRILLE ASSEMBLY,FRONT(SINGLE)
67306012
238310
ESCUTCHEON
67500114
W48602
CLAMP,SPRING
67302500
346811
MOTOR ASSEMBLY,SINGLE
67303023
147581
LOUVER,HORIZONTAL
67306205
147582-1
LOUVER,VERTICAL
67306256
147582-2
LOUVER,VERTICAL
67306257
349600
BRACKET,MOTOR
67303606
149980
SHROUD
67500112
550140
DAMPER,COMPRESSOR
67305000
152302
FILTER,AIR
67500113
352380
AIR GUIDE
67302741
359012
FAN,TURBO
67302607
559011
FAN ASSEMBLY,AXIAL
67303202
567480
THERMISTOR ASSEMBLY
67307804
264110
POWER CORD ASSEMBLY
67300027
267110
REMOTE CONTROLLER ASSEMBLY
67302239
567502
OverloadProtect
67301905
268711-2
PWB(PCB) ASSEMBLY,MAIN
67307620
268711-1
PWB(PCB) ASSEMBLY,DISPLAY
67307619
435300
GRILLE,REAR
67304801
237200
PANEL,CONTROL
67305510
731273
INSTALL PART ASSEMBLY,SINGLE
67306311
249950
CASE ASSEMBLY,CONTROL
67305522
435301
GRILLE,REAR
67304801
349480
ORIFICE
67303409
—26—
www.sylvane.com 1-800-934-9194
LocNo
Description
US10C30
W0CZZ
CAPACITOR,FILM,BOX
67300709
130410
BASE ASSEMBLY,SINGLE
67302925
130900
CABINET
67303717
132100
FRAME
67308102
135303
GRILLE,INLET
67306106
135312
GRILLE ASSEMBLY,FRONT(SINGLE)
67306012
238310
ESCUTCHEON
67500114
W48602
CLAMP,SPRING
67302500
346811
MOTOR ASSEMBLY,SINGLE
67303024
147581
LOUVER,HORIZONTAL
67306205
147582-1
LOUVER,VERTICAL
67306256
147582-2
LOUVER,VERTICAL
67306257
149980
SHROUD
67500112
550140
DAMPER,COMPRESSOR
67305000
152302
FILTER,AIR
67500113
352380
AIR GUIDE
67302740
359012
FAN,TURBO
67302607
559011
FAN ASSEMBLY,AXIAL
67303202
567480
THERMISTOR ASSEMBLY
67307804
264110
POWER CORD ASSEMBLY
67300026
267110
REMOTE CONTROLLER ASSEMBLY
67302239
567502
OverloadProtect
67301908
268711-2
PWB(PCB) ASSEMBLY,MAIN
67307618
268711-1
PWB(PCB) ASSEMBLY,DISPLAY
67307619
435300
GRILLE,REAR
67304801
237200
PANEL,CONTROL
67305510
731273
INSTALL PART ASSEMBLY,SINGLE
67306311
249950
CASE ASSEMBLY,CONTROL
67305523
435301
GRILLE,REAR
67304801
349480
ORIFICE
67303409
—27—
www.sylvane.com 1-800-934-9194
LocNo
Description
US12C10
W0CZZ
CAPACITOR,FILM,BOX
67300729
130410
BASE ASSEMBLY,SINGLE
67305520
130900
CABINET
67303717
132100
FRAME
67308102
135303
GRILLE,INLET
67306106
135312
GRILLE ASSEMBLY,FRONT(SINGLE)
67306012
238310
ESCUTCHEON
67500114
W48602
CLAMP,SPRING
67302500
346811
MOTOR ASSEMBLY,SINGLE
67303023
147581
LOUVER,HORIZONTAL
67306205
147582-1
LOUVER,VERTICAL
67306256
147582-2
LOUVER,VERTICAL
67306257
349600
BRACKET,MOTOR
67303606
149980
SHROUD
67500112
550140
DAMPER,COMPRESSOR
67305000
152302
FILTER,AIR
67500113
352380
AIR GUIDE
67302741
359012
FAN,TURBO
67302607
559011
FAN ASSEMBLY,AXIAL
67303202
567480
THERMISTOR ASSEMBLY
67307804
264110
POWER CORD ASSEMBLY
67300025
267110
REMOTE CONTROLLER ASSEMBLY
67302239
567502
OverloadProtect
67301905
268711-2
PWB(PCB) ASSEMBLY,MAIN
67307620
268711-1
PWB(PCB) ASSEMBLY,DISPLAY
67307619
435300
GRILLE,REAR
67304801
237200
PANEL,CONTROL
67305510
731273
INSTALL PART ASSEMBLY,SINGLE
67306311
249950
CASE ASSEMBLY,CONTROL
67305524
435301
GRILLE,REAR
67304801
349480
ORIFICE
67303409
—28—
www.sylvane.com 1-800-934-9194
LocNo·
Description
US12C30
W0CZZ
CAPACITOR,FILM,BOX
67300726
130410
BASE ASSEMBLY,SINGLE
67305520
130900
CABINET
67303717
132100
FRAME
67308102
135303
GRILLE,INLET
67306106
135312
GRILLE ASSEMBLY,FRONT(SINGLE)
67306012
238310
ESCUTCHEON
67500114
W48602
CLAMP,SPRING
67302500
346811
MOTOR ASSEMBLY,SINGLE
67303037
147581
LOUVER,HORIZONTAL
67306205
147582-1
LOUVER,VERTICAL
67306256
147582-2
LOUVER,VERTICAL
67306257
349600
BRACKET,MOTOR
67303606
149980
SHROUD
67500112
550140
DAMPER,COMPRESSOR
67305000
152302
FILTER,AIR
67500113
352380
AIR GUIDE
67302741
359012
FAN,TURBO
67302607
559011
FAN ASSEMBLY,AXIAL
67303202
567480
THERMISTOR ASSEMBLY
67307804
264110
POWER CORD ASSEMBLY
67300026
267110
REMOTE CONTROLLER ASSEMBLY
67302239
567502
OverloadProtect
67301906
268711-2
PWB(PCB) ASSEMBLY,MAIN
67307618
268711-1
PWB(PCB) ASSEMBLY,DISPLAY
67307619
435300
GRILLE,REAR
67304801
237200
PANEL,CONTROL
67305510
731273
INSTALL PART ASSEMBLY,SINGLE
67306311
249950
CASE ASSEMBLY,CONTROL
67305525
435301
GRILLE,REAR
67304801
349480
ORIFICE
67303409
—29—
www.sylvane.com 1-800-934-9194
LocNo·
Description
US14C30
W0CZZ
CAPACITOR,FILM,BOX
67300709
130410
BASE ASSEMBLY,SINGLE
67302926
130900
CABINET
67303717
132100
FRAME
67308102
135303
GRILLE,INLET
67306106
135312
GRILLE ASSEMBLY,FRONT(SINGLE)
67306012
238310
ESCUTCHEON
67500114
W48602
CLAMP,SPRING
67302500
346811
MOTOR ASSEMBLY,SINGLE
67303037
147581
LOUVER,HORIZONTAL
67306205
147582-1
LOUVER,VERTICAL
67306256
147582-2
LOUVER,VERTICAL
67306257
349600
BRACKET,MOTOR
67303606
149980
SHROUD
67500112
550140
DAMPER,COMPRESSOR
67305000
152302
FILTER,AIR
67500113
352380
AIR GUIDE
67302741
359012
FAN,TURBO
67302607
559011
FAN ASSEMBLY,AXIAL
67303202
567480
THERMISTOR ASSEMBLY
67307804
264110
POWER CORD ASSEMBLY
67300026
267110
REMOTE CONTROLLER ASSEMBLY
67302239
268711-2
PWB(PCB) ASSEMBLY,MAIN
67307618
268711-1
PWB(PCB) ASSEMBLY,DISPLAY
67307619
435300
GRILLE,REAR
67304801
237200
PANEL,CONTROL
67305510
731273
INSTALL PART ASSEMBLY,SINGLE
67306311
249950
CASE ASSEMBLY,CONTROL
67305526
435301
GRILLE,REAR
67304801
349480
ORIFICE
67303409
—30—
www.sylvane.com 1-800-934-9194
FRIEDRICH AIR CONDITIONING CO.
Visit our web site at www.friedrich.com
Post Office Box 1540 • 4200 N. Pan Am Expressway • San Antonio, Texas 78295-1540
• (210) 357-4400 • FAX (210) 357-4480
P/NO.:3828A20294U
Printed in the U.S.A
Unifit Cool Svc Parts 2010 (05/10)