Operating instructions | Frigidaire 134533800A Washer User Manual

Owner's Guide
Manual del Usuario
Important Safety Instructions ... ..............................................2
Washing Procedures ................ ...........................................3-5
Stain Removal ........................ ...........................................5-6
Common Washing Problems ... ..............................................7
Care and Cleaning ................. ..............................................8
Avoid Service Checklist ........... ......................................... 9-10
Warranty........................................................................... 11
Español........................................................................ 12-20
Instrucciones Importantes de Seguridad..................................12
Procedimientos para el Lavado.........................................13-15
Cómo Remover Manchas................................................15-16
Problemas Comunes del Lavado........................................
Limpieza y Cuidado............................................................18
Lista de Control de Averías..............................................19-20
Product Registration
Thank you for choosing this
washer. This owner's guide will
explain proper operation and care.
Register Your Product
The self-addressed PRODUCT
filled in completely, signed and
Registro del Producto
Le agradecemos que haya seleccionado esta lavadora. En este manual
del usuario encontrará las intrucciones
apropiadas para su funcionamiento y
Registre su Producto
PRODUCTO ya dirigida debe ser
llenada, firmada y enviada.
Read and Save These Instructions
Record Your Model and Serial Numbers
Record below the model and serial numbers found on the washer
serial plate located on the underside of the washer lid. Keep these
numbers for future reference.
Anote su Número de Modelo y de Serie
Anote a continuación los números de serie y de modelo que se
encuentran en la placa de series de la lavadora ubicada en el reverso
de la tapa de la lavadora. Guarde estos números para futura
Model Number:
Número de Modelo:
Serial Number:
Número de Serie:
Purchase Date:
Fecha de compra:
P/N 134533800A (0504)
This Owner's Guide provides general
operating instructions for your washer. It
also contains information about features
for several other models. Your washer
may not have every feature included
here. Use the washer only as instructed in
this Owner's Guide and the Operating
Instructions card included with your
Avoid fire hazard or
electrical shock. Do not use an adaptor
plug or extension cord or remove
grounding prong from electrical power
cord. Failure to follow this warning can
type fire or death.
serious injury,
wall receptacle
Grounding type
wall receptacle
Do not
not under
any circumstances
cut, remove,
or bypass
the grounding
grounding prong
from this
this plug
Power supply
with 3-prong
cord withplug
grounding plug
Use this way ONLY
Do not use or mix liquid
chlorine bleach with other household
chemicals such as toilet cleaners, rust
removers, acid or products containing
ammonia. These mixtures can produce
dangerous fumes which can cause serious
injury or death.
Important Safety Instructions
Read all instructions before using this washer.
To reduce the risk of fire, electrical shock, or injury to persons when using this washer,
comply with the basic warnings listed below.
Failure to comply with these warnings could result in serious personal injuries.
Prevent Fire
Do not wash items that have been previously cleaned in, soaked in, or spotted with
gasoline, cleaning solvents, kerosene, cooking oils, waxes, etc. Do not store these items on or near the
washer. These substances give off vapors or chemical reactions that could ignite or explode.
Do not put oily or greasy rags or clothing on top of the washer. These substances give
off vapors that could ignite the materials.
Do not add gasoline, cleaning solvents, or other flammable or explosive substances to the
wash water. These substances give off vapors that could ignite or explode.
Under certain conditions, hydrogen gas may be produced in a hot water system that has
not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has
not been used for such a period, before using the washer, turn on all hot water faucets and let the
water flow from each for several minutes. This will release any accumulated hydrogen gas. Hydrogen
gas is flammable; do not smoke or use an open flame during this time.
Failure to comply with these warnings could result in fire, explosion, serious bodily injury and/or
damage to the rubber or plastic parts of the washer.
Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this
or any other appliance.
Protect Children
Do not allow children to play on or in the washer. Close supervision of children is necessary
when the washer is used near children. As children grow, teach them the proper, safe use of all
Destroy the carton, plastic bag and other packing materials after the washer is unpacked.
Children might use them for play. Cartons covered with rugs, bedspreads or plastic sheets can become
airtight chambers.
Keep laundry products out of children's reach. To prevent personal injury, observe all
warnings on product labels.
Before the washer is removed from service or discarded, remove the washer lid to prevent
accidental entrapment.
Failure to comply with these warnings could result in serious personal injuries.
Note: The instructions appearing in this
Owner's Guide are not meant to cover
every possible condition and situation that
may occur. Common sense and caution
must be practiced when installing, operating
and maintaining any appliance.
Prevent Injury
To prevent shock hazard and assure stability during operation, the washer must be
installed and electrically grounded by a qualified service person in accordance with local codes.
Installation instructions are packed in the washer for installer's reference. Refer to INSTALLATION
INSTRUCTIONS for detailed grounding procedures. If the washer is moved to a new location, have it
checked and reinstalled by a qualified service person.
To prevent personal injury or damage to the washer, the electrical power cord of the
washer must be plugged into a properly grounded and polarized 3-prong outlet. The third grounding
prong must never be removed. Never ground the washer to a gas pipe. Do not use an extension
cord or an adaptor plug.
Follow package directions when using laundry products. Incorrect usage can produce
poisonous gas--resulting in serious injury or death.
Do not combine laundry products for use in 1 load unless specified on the label.
Do not mix chlorine bleach with ammonia or acids such as vinegar.
To prevent serious personal injury and damage to the washer:
All repairs and servicing must be performed by an authorized servicer unless specifically
recommended in this Owner's Guide. Use only authorized factory parts.
Do not tamper with controls.
Do not install or store the washer where it will be exposed to the weather.
ALWAYS disconnect the washer from the electrical supply before attempting any service
or cleaning. Failure to do so can result in electrical shock or injury.
To prevent injury, do not reach into the washer while parts are moving. Before loading,
unloading or adding items, push in the cycle selector knob and allow the tub to coast to a complete stop
before reaching inside.
Failure to comply with these warnings could result in serious personal injuries.
This washer is equipped with an electrical overload protector. The motor will stop if it becomes
overheated. The washer will automatically restart after a cool down period of up to 30 minutes, if the
washer has not been manually turned off during this time.
Printed in U.S.A.
Washing Procedures
Follow the guidelines below for preparing the wash load.
Read the Operating Instructions card for operating your specific model.
Always read and follow fabric care and laundry product labels.
To reduce the risk of fire, electrical shock, or injury to persons, read
Important Safety Instructions, pages 2-3, before operating this washer.
1. Sort laundry into loads that can be washed together.
Sort laundry into loads that can be
washed together.
Sort items by recommended water temperatures, wash time, and agitate/spin
• Separate white, light, and colorfast items from dark and noncolorfast items.
• Separate items which shed lint from items which attract lint. Permanent
press, synthetic, knit and corduroy items will pick up lint from towels, rugs
and chenille bedspreads.
• Separate heavily soiled items from lightly soiled items.
• Separate lacy, sheer and loosely knit items from sturdy items.
2. Prepare items for washing.
Empty pockets.
Brush off lint and dirt. Shake out rugs and beach towels.
Close zippers, fasten hooks, tie strings and sashes, and remove nonwashable
trims and ornaments.
Remove pins, decorative buttons, belt buckles, and other objects which
could be damaged. This also helps protect other items in the wash load.
Mend rips and tears to prevent further damage during washing.
Place delicate items such as bras, shoulder pads, hosiery, and belts in a mesh
bag to prevent tangling during the wash cycle.
Turn knit items inside out to prevent pilling.
Empty pockets.
3. Pretreat stains and heavy soil.
See Stain Removal, pages 6-7, for details.
4. Add a measured amount of detergent to the wash tub
before adding the laundry load.
Follow detergent manufacturer's directions. The amount required depends on
type of detergent, load size and soil level, and water hardness.
5. If desired, add liquid bleach to Bleach Dispenser (some models).
Before adding the wash load, add liquid bleach to bleach dispenser located
in left front corner under the lid:
• 3/4 cup (180 ml) for small loads
• 1 cup (240 ml) for large loads
• 1-1/4 cups (300 ml) for extra-large loads.
Then add 1 cup (240 ml) water to flush the dispenser.
Do not use powdered bleach in the bleach dispenser.
Place delicate items in a mesh bag.
For models without a bleach dispenser, dilute the recommended amount of
liquid chlorine bleach in 1 quart (.95 L) water. Add it to wash water after
a few minutes of agitation. Do not pour bleach directly on wash load.
Bleach Dispenser (some models)
Washing Procedures
Do not load items above
top row of holes in wash tub.
6. Add laundry load to washer.
Dry load level should not be higher than top row of holes in wash tub.
Do not overload washer.
Do not put items on top of agitator or wrap them around it. Load items
Combine large and small items in a load. Load large items first. Large items
should not be more than half the total wash load.
When washing a single heavy item, add 1 or 2 towels to balance the load.
7. If desired, add liquid fabric softener to Fabric Softener
Dispenser (some models).
For models with a built-in dispenser (see picture to the left):
1. Add liquid softener to the dispenser, following fabric softener label directions.
2. Add water to bring liquid level to fill line on dispenser cap.
3. Remove the dispenser from the agitator after each use. Rinse both cap and
cup with warm water. Replace dispenser in the agitator.
NOTE: To separate cap from cup, put thumb into dispenser and push against side
of cup (see picture to the left). After cleaning, push cap and cup firmly together.
Replace dispenser by lining up the ribs and grooves and snapping it into position.
Built-In Fabric Softener Dispenser
(some models)
Fabric softener will be flushed from area under the built-in fabric softener
dispenser when Large Load Water Level is selected. If a build-up of fabric softener
occurs, clean with hot water. DO NOT REMOVE SERVICE CAP.
For models with a removable dispenser (see picture below to the left):
1. Attach fabric softener dispenser to top of agitator by pressing down gently.
2. Add softener to the dispenser, following fabric softener label directions.
3. Add water to bring liquid level to top of the peg in the center of the cup.
4. Remove the dispenser from the agitator after each use. Rinse both lid and
bowl thoroughly with warm water. Reassemble and place dispenser on
agitator or store it nearby.
For models without a fabric softener dispenser, follow fabric softener label
directions. Add diluted fabric softener to the final rinse. Do not pour fabric
softener directly on the wash load.
Built-In Fabric Softener Dispenser
(some models)
8. Set cycle selector knob and washer controls according to
type, size, and soil level of each load, and detergent used.
See Operating Instructions card for your specific model controls.
Removable Fabric Softener Dispenser
(some models)
Washing Procedures
9. Start the washer.
Close the washer lid and pull out the cycle selector knob. The washer will not
agitate or spin with the lid open.
To stop the washer, push in the cycle selector knob.
Do not stop and restart washer during a spin when using the fabric softener
To change a cycle, push in the cycle selector knob. Turn it clockwise to the
desired setting. Pull out the knob to restart the washer.
10. Remove items when the cycle is completed.
For your safety, the lid locks when the tub is spinning. It will remain locked for
about 1 minute after the tub stops spinning.
To open the lid during a spin, push in the cycle selector knob and wait about
1 minute for the lid lock to release. Do not force open the locked lid.
Place washed items in automatic dryer, line dry, or dry flat as directed by fabric
care label. Excess wrinkling, color transfer or odors may develop in items left in
the washer after the cycle has ended.
To avoid serious personal injury, do not operate washer if safety lid
lock is missing or damaged.
Stain Removal
Safe Stain Removal Procedures
To reduce the risk of fire or serious injury to persons or property,
comply with the basic warnings listed below:
Read and comply with all instructions on stain removal products.
Keep products in their original labeled containers and out of children's
Thoroughly wash any utensil used.
Do not combine stain removal products, especially ammonia and chlorine
bleach. Dangerous fumes may result.
Never wash items which have been previously cleaned in, washed in,
soaked in or spotted with gasoline, dry cleaning solvents or other flammable
or explosive substances because they give off vapors that could ignite or
Never use highly flammable solvents, such as gasoline, inside the home.
Vapors can explode on contact with flames or sparks.
Do not combine stain removal products.
For successful stain removal:
• Remove stains promptly.
Follow fabric care label instructions.
Determine the kind of stain, then follow recommended treatment in the
stain removal chart on the next page.
To pretreat stains, use a prewash product, liquid detergent, or a paste made
from granular detergent and water.
Use cold water on unknown stains because hot water can set stains.
Check care label instructions for treatments to avoid on specific fabrics.
Check for colorfastness by testing stain remover on an inside seam.
Rinse and wash items after stain removal.
Stain Removal
Adhesive tape, chewing gum, Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or
nonflammable dry cleaning fluid.
rubber cement
Baby formula, dairy products,
Use product containing enzymes to pretreat or soak stains. Soak for 30 minutes or more. Wash.
Beverages (coffee, tea, soda,
juice, alcoholic beverages)
Pretreat stain. Wash using cold water and bleach safe for fabric.
Rinse with cold water. Rub with bar soap. Or, pretreat or soak with product containing enzymes. Wash using
bleach safe for fabric.
Candle wax, crayon
Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed.
Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning
fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.
Collar or cuff soil, cosmetics
Pretreat with prewash stain remover or rub with bar soap.
Dye transfer on white fabric
Use packaged color remover. Wash using bleach safe for fabric.
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.
Grease, oil, tar (butter, fats,
salad dressing, cooking oils,
car grease, motor oils)
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply
nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse thoroughly. Wash
using hottest water safe for fabric.
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured
alcohol or nonflammable dry cleaning fluid.
Mildew, scorch
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and hot water before washing. Badly
mildewed fabrics may be permanently damaged.
Brush off dry mud. Pretreat or soak with product containing enzymes.
Mustard, tomato
Pretreat with prewash stain remover. Wash using bleach safe for fabric.
Nail polish
May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.
Repeat, replacing paper towels frequently. Do not use on acetate fabrics.
Paint, varnish
WATER BASED: Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed. OIL
BASED AND VARNISH: Use solvent recommended on can label. Rinse thoroughly before washing.
Use prewash stain remover or rub with bar soap. Rinse. Wash using nonchlorine bleach in hottest water safe for
Rust, brown or yellow
For spots, use rust remover safe for fabric. For discoloration of an entire load, use nonchlorine bleach. Do not use
chlorine bleach because it may intensify discoloration.
Shoe polish
LIQUID: Pretreat with a paste of granular detergent and water. PASTE: Scrape residue from fabric. Pretreat with
prewash stain remover or nonflammable dry cleaning fluid. Rinse. Rub detergent into dampened area. Wash using
bleach safe for fabric.
Urine, vomit, mucus, feces
Pretreat or soak in product containing enzymes. Wash using bleach safe for fabric.
Common Washing Problems
Many washing problems involve poor soil and stain removal, residues of lint and scum, and fabric damage. For satisfactory washing
results, follow these suggestions provided by The Soap and Detergent Association.
Blue stains
•Detergent or liquid fabric softener
did not dissolve or disperse.
•If caused by detergent, mix 1 cup (240 ml)
white vinegar with 1 quart (.95 L) water
in a plastic container. Soak item 1 hour.
•If caused by fabric softener, rub stains
with bar soap. Wash.
•Add detergent before wash load. Then
start washer.
•Dilute fabric softener with water.
•Not enough detergent.
•Wash water temperature too low.
•Incorrect sorting.
•Rewash with correct amount of
detergent and hottest water safe for
fabric. Add bleach safe for fabric.
•Sort items by soil level and color.
•Use correct amount of detergent, hottest
water and bleach safe for fabric.
Greasy, oily stains
•Not enough detergent.
•Undiluted liquid fabric softener
poured directly on fabric.
•Treat with prewash stain remover or
liquid detergent.
•Increase detergent and water
temperature. Rewash.
•Rub fabric softener stains with bar soap.
•Use correct amount of detergent and
hottest water safe for fabric.
•Do not pour liquid fabric softener
directly on fabric. See package directions
or Washing Procedures for proper
Holes, tears, or
•Incorrect use of chlorine bleach.
•Unfastened zippers, hooks,
•Rips, tears and broken threads.
•Overloading the washer.
•Degradation of fabric.
•May be irreversible if rips, tears and seams •Never pour chlorine bleach directly on
cannot be mended.
•Check condition of items before washing.
See Washing Procedures for preparing
and loading the wash load.
•Incorrect sorting.
•Tissues left in pocket.
•Overloading the washer.
•Not enough detergent.
•Undissolved detergent has left
•Static cling is attracting lint.
•Load washed too long.
•Reduce load size. Rewash using correct
water temperature, water level, and
amount of detergent.
•Add nonprecipitating water conditioner
to wash water.
• Add liquid fabric softener to final rinse.
•Dry load in dryer.
•Remove lint with lint brush or roller.
•See Washing Procedures for sorting and
preparing the wash load.
•Do not overload washer.
•Use correct amount of detergent, water
temperature and water level.
(Fibers break off,
ball up and cling to
•Pilling is normal with synthetic and
permanent press fabrics. This is due
to abrasion from normal wear.
•Use a lint brush or shaver to remove pills.
•Use fabric softener in the washer to
lubricate fibers.
•When ironing, use spray starch or fabric
finish on collars and cuffs.
•Turn items inside out to reduce abrasion.
Residue or powder •Undissolved detergent.
on dark items;
•Some nonphosphate granular
Stiff, harsh fabrics. detergents can combine with hard
water minerals to form a residue.
•Reduce load size.
•Add dissolved detergent to tub . Rewash
•Mix 1 cup (240 ml) white vinegar to 1
gallon (3.8 L) warm water in plastic
container. Soak item. Rinse and rewash.
•Increase water temperature using hottest
water safe for fabric.
•Do not overload washer.
•Use liquid detergent or use nonprecipitating
water conditioner with nonphosphate
granular detergent.
•Reduce load size.
•Rinse in cold water with liquid fabric
•Do not overload washer.
•Remove items from washer as soon as cycle
is completed.
•Use liquid fabric softener.
Yellow buildup of •Agitation time too short.
body soil on
•Wash water temperature too low.
synthetic fabrics
•Not enough detergent.
•Soak in detergent booster or product
containing enzymes.
•Wash in hot water (120°F/49°C) using full
permanent press cycle. Increase
Add bleach safe for fabric.
•Or, treat with color remover.
•Wash synthetics frequently using water at
least 100°F (37°C ) and correct water level.
Yellow or brown
rust stains
•To restore discolored load of whites, use
rust remover safe for fabric.
Do not use chlorine bleach to remove
rust stains. It may intensify
•Use nonprecipitating water softener.
•Before washing, run hot water for a few
minutes to clear lines.
•Drain water heater occasionally.
•For an ongoing problem, install an iron filter
in your water supply system.
•Overloading the washer.
•Iron or manganese in water supply,
water pipes, or water heater.
Care and Cleaning
Use care with laundry
products. They can damage finish on
the washer.
Remove items from the washer as soon as the cycle ends. Excess wrinkling, color
transfer, and odors may develop in items left in the washer.
Dry the washer top, the area around the lid opening, and the underside of the
lid. These areas should always be dry before the lid is closed.
Before cleaning the washer interior, unplug the electrical power cord to avoid
electrical shock hazards.
When extremely soiled items have been washed, a dirty residue may remain on
the tub. Remove this by wiping the tub with a nonabrasive household cleanser.
Rinse thoroughly with water.
The agitator or tub may become stained from fabric dye. Clean these parts with
a nonabrasive household cleanser. This prevents dye transfer to future loads.
When washing is completed, wipe top and sides of washer with a damp cloth.
Turn water faucets off to prevent pressure build-up in the hoses.
As needed, clean the cabinet with mild soap and water. Never use harsh, gritty
or abrasive cleansers. If top or lid becomes stained, clean with diluted chlorine
bleach [1/2 cup (120 ml) in 1 quart (.95 L) water]. Rinse several times with clear
Remove glue residue from tape or labels with a mixture of warm water and mild
detergent. Or, touch residue with the sticky side of the tape or label.
Before moving the washer, place a strip of cardboard or thin fiberboard under
the front leveling legs to prevent floor damage.
Winterizing Instructions
If the washer is stored in an area where freezing can occur or moved in freezing
temperatures, follow these winterizing instructions to prevent damage to the washer:
Follow Winterizing
Instructions for cold
weather care.
Turn off water supply faucets.
Disconnect hoses from water supply and drain water from hoses.
Plug electrical cord into a properly grounded electrical outlet.
Add 1 gallon nontoxic recreational vehicle (RV) antifreeze to empty wash tub.
Close lid.
Set cycle selector knob at a spin setting. Pull out knob and let washer spin for
1 minute to drain out all water. Not all of the RV antifreeze will be expelled.
Push in knob, unplug electrical power cord, dry tub interior, and close lid.
Store washer in an upright position.
To remove antifreeze from washer after storage, run empty washer through a
complete cycle using detergent. Do not add wash load.
Avoid Service
Before calling for service, review this list. It may save both time and expense. The list includes
common concerns that are not the result of defective workmanship or materials in this washer.
A certain amount of "clunking" or gear
sounds are normal in a heavy-duty
This is normal.
Rattling and clanking
Foreign objects such as coins or safety
pins may be in tub or pump.
Stop washer and check tub. If noise continues after
washer is restarted, objects may be in pump. Call your
authorized servicer.
Belt buckles and metal fasteners are
hitting wash tub.
To prevent unnecessary noise and damage to tub,
fasten fasteners and turn items inside out.
Squealing sound or hot
rubber odor.
Washer is overloaded.
Do not overload washer. Stop washer and reduce
Thumping sound.
Heavy wash loads may produce a
thumping sound.
This is usually normal. If sound continues, washer is
probably out of balance. Stop washer and redistribute
wash load.
Vibrating noise.
Washer is not resting firmly on floor.
Move washer so it rests firmly on floor. Adjust leveling
Shipping bolt and block have not been
removed during installation.
shipping bolt and block.
Wash load unevenly distributed in tub.
Stop washer and rearrange wash load.
Electrical power cord may not be plugged
in or connection may be loose.
Make sure plug fits tightly in wall outlet.
House fuse blown, circuit breaker tripped,
or a power outage has occurred.
Reset circuit breaker or replace fuse. Do not increase
fuse capacity. If problem is a circuit overload, have it
corrected by a qualified electrician. If problem is a
power outage, call local electric company.
Water supply faucets are not turned on.
Turn on water supply faucets.
Cycle selector is not in correct position.
Move indicator clockwise slightly. Pull out knob.
Motor is overheated.
Washer motor will stop if it becomes overheated. It
will automatically restart after a cool down period of
up to 30 minutes (if washer has not been manually
turned off).
Lid is not completely closed.
Close lid completely.
Heavily soiled items.
Wipe tub with a nonabrasive household cleanser, then
rinse. Shake or brush excess dirt and sand from items
before washing.
Washer does not start.
Washer won't spin.
Washer is overloaded.
Load is out of balance.
Do not overload washer. See Washing
Rearrange load to allow proper spinning.
Drain hose is kinked.
Straighten drain hose.
Water supply is not adequate in area.
Check another faucet in the house. Wait until
water supply and pressure increase.
Water supply faucets are not completely
Fully open hot and cold faucets.
Water is being used elsewhere in the house.
Water pressure must be at least 30 psi (260 kPa).
Avoid running water elsewhere while washer is
Water inlet hoses are kinked.
Straighten hoses.
Improper water level selection (for models
with water level/load size control).
Select higher water level/load size.
Washer is overloaded.
Do not overload washer. When control is set at
highest fill level, dry load level should not be
higher than top row of circular holes in wash tub.
Hot water heater is set too low or is a distance
from washer.
Measure hot water temperature at nearby faucet
with candy or meat thermometer. Water
temperature should be at least 130°F (70°C).
Adjust water heater as necessary.
Hot water is being used elsewhere in the
Avoid using hot water elsewhere before or during
washer use. There may not be enough hot water
available for proper cleaning. If problem persists,
your hot water system may be unable to support
more than 1 use at a time.
Drain hose is kinked or clogged.
Clean and straighten the drain hose.
Fill hose connection at faucet or washer.
Check and tighten hose connections. Install rubber
sealing washers provided.
House drain pipes are clogged.
Unclog drain pipes. Contact plumber if necessary.
Use less detergent.
Incorrect wash and rinse
Hot and cold water hoses are connected to
wrong supply faucets.
Connect hot water hose to hot water faucet and
cold water hose to cold water faucet.
Water is entering washer
but tub does not fill.
Drain hose standpipe is incorrect height.
Standpipe must be a minimum of 33" (83.82 cm)
high to prevent siphoning. See INSTALLATION
Residue left in tub.
Wash load too wet after
Water does not enter
washer or it enters
Water level does not
cover load.
Warm or hot water is not
hot enough.
Water in washer does not
drain or drains slowly.
Water leaks.
Your Frigidaire product is protected by this warranty
One year from original
purchase date.
Pay all costs for repairing or replacing any parts of this appliance
which prove to be defective in materials or workmanship.
Costs of service calls that are listed under NORMAL
Second through fifth years
from original purchase date.
Provide a replacement for a defective or malfunctioning part found
in the washer transmission.
Costs for labor and replacement parts other than
defective transmission parts.
(Excluding Alaska)
25 years from original
purchase date.
Provide a replacement and in-home service labor, without charge,
for an inner wash basket that breaks due to defective materials
or workmanship.
Costs of service calls that are listed under NORMAL
Time periods listed above.
(Applicable to the State
of Alaska)
All of the provisions of the full and limited warranties above and
the exclusions listed below apply.
Costs of the technician's travel to the home and any costs
for pick up and delivery of the appliance required
because of service.
Your appliance is warranted by Frigidaire Company, a division of White Consolidated Industries, Inc. We authorize no person to change or add to any of our
obligations under this warranty. Our obligations for service and parts under this warranty must be performed by Frigidaire Company Consumer Services or
an authorized Frigidaire servicer.
This warranty applies only to products in ordinary household use, and the consumer is responsible for the items listed
1. Proper use of the appliance in accordance with instructions provided with the product.
2. Proper installation by an authorized servicer in accordance with instructions provided with the appliance and in accordance
with all local plumbing, electrical and/or gas codes.
3. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose connections
or defects in house wiring.
4. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc., which are not
a part of the appliance when it was shipped from the factory.
5. Damages to finish after installation.
6. Replacement of light bulbs and/or fluorescent tubes (on models with these features).
This warranty does not cover the following:
Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion
may not apply to you.
2. Service calls which do not involve malfunction or defects in workmanship or material, or for appliances not in ordinary household
use. The consumer shall pay for such service calls.
3. Damages caused by services performed by persons other than authorized Frigidaire servicers; use of parts other than Frigidaire
Company Genuine Renewal Parts; obtained from persons other than such servicers; or external causes such as abuse, misuse,
inadequate power supply or acts of God.
4. Products with original serial numbers that have been removed or altered and cannot be readily determined.
Keep your bill of sale, delivery slip, or some other appropriate payment record. The date on the bill establishes the warranty period
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts. This written warranty
gives you specific legal rights. You may also have other rights that vary from state to state. Service under this warranty must be
obtained by following these steps, in order:
Contact Frigidaire Company Consumer Services or an authorized Frigidaire servicer.
If there is a question as to where to obtain service, contact our Consumer Assistance Center at:
P.O. Box 7181
Dublin, Ohio 43017
(800) 944-9044
Product features or specifications as described or illustrated are subject to change without notice. All warranties are made by White
Consolidated Industries, Inc. This warranty applies only in the 50 states of the U.S.A. and Puerto Rico.
Download PDF