Frigidaire 154768201 Dishwasher User Manual

Standard Dry Air Flow
Exploded View of Wash System
When the control advances to the “dry” portion of
the cycle, a vent actuation solenoid is closed.
This opens the vent valve and starts the vent fan
both located in the top right rear corner of the tub.
The fan draws in the air from outside the tub,
forcing the hot, humid air down and out the
T
U
B
Delivery
Tube
bottom of the outer door panel. This outside,
cooler, dryer air helps to speed evaporation of
water from the hot dishes. At the same time the
heating element is continually cycled on and off.
On some models the dry portion of the cycle can
be extended to improve drying performance.
3rd Level
Spray Arm
Assy.
Middle
Spray Arm
Assy.
Lower
Spray Arm
Soil
Director
Spray Arm
Support
Soil
Filter
Volute
Cover
Check
Ball
Filter
Personal Injury Hazard
Always disconnect the dishwasher from the electrical power source before adjusting or
replacing components.
Symptom
Check the Following
Remedy
Dishwasher will not operate when
turned on.
1. Fuse (blown or tripped).
2. 120 VAC supply wiring connection
faulty.
3. Electronic control board defective.
4. No 12 VAC power to control.
5. Motor (inoperative).
6. Door switch (open contacts).
7. Door latch not making contact with
door switch.
8. Touch pad circuit defective.
9. No indicator lamps illuminate when
START or OPTIONS are pressed.
1. Replace fuse or reset breaker.
2. Repair or replace wire fasteners at
dishwasher junction box.
3. Replace control board.
4. Replace control board.
5. Replace motor/impeller assembly.
6. Replace latch assembly.
7. Replace latch assembly.
Motor hums but will not start or run.
1. Motor (bad bearings).
2. Motor stuck due to prolonged
non-use.
1. Replace motor assembly.
2. Rotate motor impeller.
Motor trips out on internal thermal
overload protector.
1. Improper voltage.
2. Motor windings shorted.
3. Glass or foreign items in pump.
1. Check voltage.
2. Replace motor/impeller assembly.
3. Clean and clear blockage.
Dishwasher runs but will not heat.
1.
2.
3.
4.
Heater element (open).
Electronic control board defective.
Wiring or terminal defective.
Hi-Limit thermostat defective.
1.
2.
3.
4.
Replace heater element.
Replace control board.
Repair or replace.
Replace thermostat.
Detergent cover will not latch or
open.
1.
2.
3.
4.
5.
Latch mechanism defective.
Electronic control board defective.
Wiring or terminal defective.
Broken spring(s).
Defective actuator.
1.
2.
3.
4.
5.
Replace dispenser.
Replace control board.
Repair or replace.
Replace dispenser.
Replace dispenser.
Dishwasher will not pump out.
1.
2.
3.
4.
5.
6.
Drain restricted.
Electronic control board defective.
Defective drain pump.
Blocked impeller.
Open windings.
Wiring or terminal defective.
1.
2.
3.
4.
5.
6.
Clear restrictions.
Replace control board.
Replace pump.
Check for blockage, clear.
Replace pump assembly.
Repair or replace.
Dishwasher will not fill with water.
1. Water supply turned off.
2. Defective water inlet fill valve.
3. Check fill valve screen for
obstructions.
4. Defective float switch.
5. Electronic control board defective.
6. Wiring or terminal defective.
7. Float stuck in “UP” position.
1. Turn water supply on.
2. Replace water inlet fill valve.
3. Disassemble and clean screen.
1. Drain hose (high) loop too low.
1. Repair to proper 32-inch minimum
height.
2. Install air gap at counter top.
Detergent and Rinse Aid Dispenser
The detergent and rinse aid dispenser is a one
piece component consisting of a molded
detergent cup and a built-in rinse aid dispenser.
Glass
Trap
Trouble Shooting Tips
Sump
Housing
To replace dispenser:
•
•
•
The detergent cup has a spring loaded cover
•
and the rinse aid dispenser has a removable
•
cover.
•
Liquid rinse aid is added to the dispenser up to •
the fill line indicator. The amount of rinse aid
released can be adjusted by turning the arrow
indicator from one, being the least amount, to
four, being the greatest amount.
shut off electricity to dishwasher,
remove outer door panel assembly,
disconnect wiring to the actuator,
remove the six screws,
remove the dispenser,
replace and reinstall screws,
rewire actuator.
8. Replace console assembly.
9. Replace console assembly.
Sump
Gasket
Heating
Element
Tub and Door Seal
T
U
B
Water
Bottle
Water
Inlet Tube
Motor
Bracket
Water
Valve
Circulation
Motor
Drain
Pump
The door seal is pressed into the tub channel for
an interference fit. To install the seal, locate the
center mark on the seal back and press into
place. Next, install the bottom of the seal by
creating a short turn at the bottom of the tub
channel and ensuring the seal extends to the
locator ridge at the bottom of the tub. Then align
and gently press the seal into the channel in only
a few spots. Next, close and latch the door to
allow the gasket to seat properly into the channel.
Gasket Cross Section
Pump Assembly
The pump assembly is driven by a synchronous
motor. Rotation is in the counterclockwise
direction at 3600 RPM. The motor drives a pump
which supplies 100 percent filtered water at a
rate of approximately 12 GPM to one spray arm
at a time. The spray arm’s operation is alternated
by small “pauses” of the motor during the wash
cycle.
is attached by a worm gear clamp to the discharge
end of the drain pump.
The drain hose must have a loop at a minimum
height of 32 inches in order to insure proper
drainage.
The main pump can easily be removed by
disconnecting the upper spray arm supply tube
hose, the drain pump connector hose, the wiring
Draining is accomplished by using a small
harness connections made at the circulation
separate synchronous drain pump mounted to
motor, the water heat thermistor located on the
the side of the sump. The drain pump is
bottom of the pump and rotating the four sump
connected to the main pump by a small rubber
retainers toward the middle of the sump.
Product Specifications
hose. The drain check valve is located at the
Electrical
discharge end of the drain pump. The drain hose
Rating ................................... 120 Volts, 60Hz
Separate Circuit..15 amp min.- 20 amp max.
Motor (Amps) ........................................... 1.8
Heater Wattage ....................................... 900
Total Amps (load rated) ......................... 10.0
TempAssure .............................. 140°F ±5°F
(60°C±3°C) [with outer door in place]
TempBoost ............. 145°F ±5°F (63°C ±3°C)
Heated Wash/Heated Rinse
Sanitize .................. 150°F ±5°F (66°C ±3°C)
Hi-Limit Thermostat ................ 200°F (93°C)
Mounting
Rib
Tub
Interior
Dishwasher water siphons out.
Short Turn
2. Drain line connected to a floor drain
not vented.
Detergent left in dispenser.
Water Supply
Suggested minimum incoming water
temperature ............................. 120°F (49°C)
Pressure (PSI) min./max. ................... 20/120
Connection (NPT) ..................................... 3/8"
Consumption (Normal Cycle) .......................
............. 4.9 - 9.7 U.S. gal., 18.5 - 36.7 liters
Water valve flow rate (U.S. GPM) ........... .83
Water recirculation rate (U.S. GPM) ..............
.................................................... approx. 12
Water fill time ..................................... 87 sec.
1. Detergent allowed to stand too long in
dispenser.
2. Dispenser wet when detergent was
added.
3. Detergent cover held closed or blocked
by large dishes.
4. Improper incoming water
temperature to properly dissolve
detergent.
5. See "Detergent cover will not open."
4.
5.
6.
7.
Repair or replace.
Replace control board.
Repair or replace.
Clean float.
1. Instruct customer/user.
2. Instruct customer/user.
3. Instruct customer/user on proper
loading of dishes.
4. Incoming water temperature of
120°F is required to properly
dissolve dishwashing detergents.
020905
Y-BK.............Yellow/Black
Cycle Selection Options
P3-6
P1
W
W
NEUT W
BK
L1
BK
P3-5
DOOR
SWITCH
BK
P2-2
P2-1
P2-3
BK
R
TURBIDITY SENSOR/
THERMISTOR
120VAC
60HZ
HEATER W
W
W
WATER VALVE
Th
UF
RA
W
P1
HI-LIMIT
THERMOSTAT R
FLOAT
SWITCH PK
P3- 1
P6
DISPLAY
ELECTRONIC
CONTROL
BOARD
P2- 4
P2- 5
P2- 6
R
W
BK
P3- 3
R-Y
P2- 8
BK
P2- 7
BK
P3-7
P3-8
Tu
HS
HALL SENSOR
Thermistor
0 0 0 0 0 0 Fan speed
0 0 0 1 0 0 Rinse aid
0 0 1 0 1 0
X - denotes selectable option
CLEAN LED stays on until door is opened or cycle is started.
Y
P3-2
VIO
P3-4
BU
Uo
W
Fan damper
Turbidity
Hall sensor
RINSE AID
LEVEL SENSE
0
0
0
1
1
1
W
0
0
0
0
0
0
DRAIN MOTOR
0
0
0
0
0
0
Display flashes when
Detection of failure
0
0
0
0
0
0
Device being monitored
FAN UNIT
1
1
1
1
0
0
1
1
1
1
0
0
PUMP MOTOR
0
0
0
0
1
1
1
1
FAN DRY UNIT
0
0
1 0
0 0
0 0
0 0
0 0
1 0
1 0 0 1
1 X 0 1
0
0
0
0
0
0
RINSE LED
0
0
1
0
1
1
DRAIN MOTOR
HEATER
DISPENSER
WATER VALVE
CIRCULATION MOTOR
1
1
0
0
0
0
CLEAN LED
60
27
45
0.4
75
60
90
90
447
DRYING LED
FILL/DISPENSER
FILL
WASH/HEAT
PAUSE
WASH/HEAT
WASH/HEAT/DISP.
DRAIN
DRY
TOTAL
SANITIZED LED
1
2
3
4
5
6
7
8
SENSING LED
WASHING LED
The dishwasher will then step
through the test cycle per the chart.
Pushing the START/CANCEL pad
will advance the dishwasher to the
next step.
STEP
While in power failure or idle
mode - simultaneously press the
DRY/AIR DRY and
START/CANCEL pads for 3
seconds.
TOTAL TIME (SEC)
The water/service test is a
special function initiated from
the power failure mode or idle
mode.
BK.......................... Black
BU............................Blue
PK............................Pink
R...............................Red
R-BK...............Red/Black
W............................White
Wiring Diagram
(Some models)
DISPENSER
For controls
and hold the RINSE ONLY or AIR DRY
lock . . . . . . . . . . Press
.
pad for 3 seconds. To unlock, press and hold the
RINSE ONLY or AIR DRY pad for 3 seconds.
BK
P32-9
R
P32-6
BK-W
P2-11
R-W
P2-12
Y/BL
P2-13
To cancel cycle
SENSING ----------------------Turbidity sensor is checking the condition of the wash/rinse water.
No sensing for LIGHT WASH (UPPER RACK), LIGHT WASH (LOWER RACK) and CHINA/CRYSTAL.
WASHING ----------------------Wash portion of cycle.
SANITIZED --------------------The SANITIZED criteria has been met. Indicator light will switch off when door is opened.
DRYING ------------------------ Drying portion of cycle.
CLEAN ------------------------ Shows completion of cycle. Indicator light will switch off when door is opened.
OPTION LED's Flashing -- HI-TEMP WASH and NO HEAT DRY/POWER DRY OFF LED's flashing indicates power failure has
occurred. Press START/CANCEL pad and reselect desired options and cycle.
STATUS LED's Flashing -- The STATUS LED's that are lit when the door is opened will flash. Close door.
RINSE AGENT LOW ------- The liquid rinse agent is low. Light will switch off after 5 complete wash cycles or dispenser is
(Some models)
filled.
or LO..Low liquid in the rinse aid dispenser
PF..........A power failure has occurred
HO or Hd.........Water heating delay
CL..........Close and latch the door
ER/ER....Switch Failure
ER/CE....Configuration Error
ER/uo.....Vent will not close
ER/uF.....Fan not running
'01-24'....Hour(s) delay before start
Press desired cycle and/or option pad. The indicator
lights will change. Press START/CANCEL within 15
seconds to begin cycle.
Press START/CANCEL. Dishwasher will drain for
90 seconds, then shut off.
Color Code
P-5
Close and latch door. Press DELAY START pad to
select desired delay time.
USER INTERFACE SWITCH
Electronic Series
P/N: 154768201
To delay start
To select a new
cycle or option
Display Codes (LED)
Display Codes (Readout)
Close and latch door. Press START/CANCEL pad.
Water/Service Test
This information is intended for use by
persons having electrical and
mechanical training and a level of
knowledge of these subjects generally
considered acceptable in the appliance
repair trade. Electrolux Home Products
North America cannot be responsible,
nor assume any liability, for injury or
damage of any kind arising from the
use of this Service Data Sheet.
SERVICE DATA SHEET
Operation
To start