Frigidaire 241666500 Refrigerator User Manual

All about the
Use & Care
of your
Wine Cooler
TA B L E O F C O N T E N T S
Important Safety Instructions..................................2
Temperature Controls.............................................6
Installation............................................................4
Care and Cleaning................................................. 7
Door Reversal Instructions......................................5
Before you Call...................................................... 8
Energy Saving Tips.................................................6
Major Appliance Warranty.....................................10
242101800 (March 2010)
www.frigidaire.com USA 1-800-944-9044
www.frigidaire.ca Canada 1-800-265-8352
SERIAL/MODEL #’S - Important Safety Instructions
Read and Save These Instructions
This Owner’s Guide provides specific operating
instructions for your model. Use your Wine Cooler only
as instructed in this guide. These instructions are not
meant to cover every possible condition and situation
that may occur. Common sense and caution must be
practiced when installing, operating, and maintaining any
appliance.
Record Your Model and Serial Numbers
Record the model and serial numbers in the space
provided below. The serial plate is located on the upper
left wall inside the Wine Cooler.
Model Number:
Serial Number:
WARNING
Please read all instructions before using this wine
cooler.
Definitions
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible injury
or death.
DANGER
DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious
injury.
Purchase Date:
WARNING
WARNING indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury.
CAUTION
CAUTION indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury.
IMPORTANT
IMPORTANT indicates installation, operation or
maintenance information which is important but not
hazard-related.
WARNING
For Your Safety
Do not store or use gasoline, or other flammable
vapors and liquids in the vicinity of this or any other
appliance. Read product labels for flammability and
other warnings.
2
Important Safety Instructions
WARNING
Electrical Information
WARNING
Child Safety
• The wine cooler must be plugged into its
own dedicated 115 Volt, 60 Hz., 15 Amp,
AC only electrical outlet. The power cord of
the appliance is equipped with a three-prong
grounding plug for your protection against
electrical shock hazards. It must be plugged
directly into a properly grounded three prong
receptacle. The receptacle must be installed in
accordance with local codes and ordinances.
Consult a qualified electrician. Avoid connecting
refrigerator to a Ground Fault Interruptor (GFI)
circuit. Do not use an extension cord or
adapter plug.
• Destroy carton, plastic bags, and any exterior
wrapping material immediately after the wine
cooler is unpacked. Children should never use
these items to play. Cartons covered with rugs,
bedspreads, plastic sheets or stretch wrap may
become airtight chambers, and can quickly cause
suffocation.
• If the power cord is damaged, it should be
replaced by an authorized service technician to
prevent any risk.
• Remove the door(s) of any appliance that is not in
use, even if it is being discarded.
• Never unplug the wine cooler by pulling on the
power cord. Always grip the plug firmly, and
pull straight out from the receptacle to prevent
damaging the power cord.
• Unplug the wine cooler before cleaning and before
replacing a light bulb to avoid electrical shock.
• Performance may be affected if the voltage varies
by 10% or more. Operating the wine cooler with
insufficient power can damage the compressor.
Such damage is not covered under your warranty.
• Do not plug the unit into an electrical outlet
controlled by a wall switch or pull cord to prevent
the wine cooler from being turned off accidentally.
• Remove all staples from the carton. Staples can
cause severe cuts, and destroy finishes if they
come in contact with other appliances or furniture.
• An empty, discarded wine cooler is a very
dangerous attraction to children.
WARNING
Proper Disposal of your Wine Cooler
Risk of child entrapment
Child entrapment and suffocation are not problems of
the past. Junked or abandoned wine coolers are still
dangerous – even if they will sit for “just a few days”.
If you are getting rid of your old wine cooler, please
follow the instructions below to help prevent accidents.
We strongly encourage responsible appliance recycling/
disposal methods. Check with your utility company or
visit www.recyclemyoldfridge.com for more information
on recycling your old wine cooler.
Before you throw away your old wine cooler:
• Remove doors.
• Leave shelves in place so children may not easily
climb inside.
• Have refrigerant removed by a qualified service
technician.
3
Installation
This Use & Care Guide provides general operating
instructions for your model. Use the refrigerator only as
instructed in this Use & Care Guide. Before starting the
wine cooler, follow these important first steps.
Location
• Choose a place that is near a grounded electrical
outlet. Do Not use an extension cord or an adapter
plug.
• For optimal performance, it is recommended that
you install the wine cooler where the ambient
temperature is between 70 and 78 degrees
fahrenheit.
• Allow space around the unit for good air circulation. Leave a 2 inch space on the back and sides of the wine cooler for adequate circulation.
• Be sure the wine cooler stays in the upright position during transport.
• Keep the wine cooler from any hazardous or
combustible agents.
 NOTE
The exterior walls of the wine cooler may become quite
warm as the compressor works to transfer heat from
the inside. Temperatures as much as 30° F warmer
than room temperature can be expected. For this
reason it is particularly important in hotter climates to
allow enough space for air circulation around your wine
cooler.
Leveling The wine cooler must have all bottom corners resting
firmly on solid floor. The floor must be strong enough
to support a fully loaded wine cooler. NOTE: It is Very
Important for your wine cooler to be level in order to
function properly. If the wine cooler is not leveled during
installation, the door may be misaligned and not close
or seal properly, causing cooling, frost, or moisture
problems.
To Level Your Wine Cooler:
After removing all interior and exterior packaging
materials, use a carpenter’s level to level the wine cooler
from front-to-back. Adjust the leveling legs in front, ½
bubble higher, so that the door closes easily when left
halfway open.
4
Cleaning
• Wash any removable parts of the wine cooler interior, and exterior with mild detergent and warm water.
Wipe dry. Do not use harsh cleaners on these
surfaces.
• Do not use razor blades or other sharp instruments, which can scratch the appliance surface when
removing adhesive labels. Any glue left from the tape
can be removed with a mixture of warm water and
mild detergent, or touch the residue with the sticky
side of tape already removed. Do not remove the
serial plate.
Important Safeguards: Do not store food in your wine
cooler as interior temperature may not get cool enough
to prevent spoilage. In summer months or areas of high
humidity, the glass door may build up moisture. To
remove the moisture, wipe it away.
INSTALLATION
Reversing the door swing
The glass door can be opened from left to right and vice
versa. Should you desire to change the opening direction,
please follow these instructions.
 NOTE
All parts removed must be saved to do the
reinstallation of the door.
Step 11:Loosen the bolt� and bottom hinge�ˈthen replace the parts on the
left and right sideˈthen assemble the parts,see chart 6.
1. Remove top cap. Remove the three screws that hold
the upper hinge (right side) to the top of the cabinet.
See Fig. 1.
Fig. 2
2. Carefully remove top hinge (See Fig. 1.), then lift the
door up off of bottom hinge and place it on a padded
surface to prevent scratching it. See Fig. 2.
Step 11:Loosen the bolt� and bottom hinge�ˈthen replace the parts on the
ĸ
left and right sideˈthen assemble
the parts,see chart 6.
Chart 2
3. Remove the three button plugs from the upper left
Step 7:Remove the bolt on the bottom of the door by screwdriver�(see chart
corner of the cabinet and transfer them to the holes
3)
ŀ
on the opposite side. Be sure to press the button
Step 8:Remove the screw� and the block �,then set them on the left side.(see
ĺ
Chart 5
plugs firmly into the holes. See Fig. 1.
chart 3)
4. Remove three screws that hold the bottom hinge to
lower end of cabinet. Remove the three button plugs
from lower LH corner and transfer to holes where
bottom hinge was just removed. See Fig. 3.
Ľ
ľ
Step 11:Loosen the bolt� and bottom hinge�ˈthen replace the parts on the
Button
plugs
left
and ĸ
right
sideˈthen assemble the parts,see chart 6.
5. Unscrew pins from both hinges and transfer to
threaded hole on opposite side. See Fig. 4. Re-install
Hinge
Screws
Fig. 3
ŀ
bottom hinge in LH corner of cabinet using same
Chart 3
� Handle
Chart 6
three
screws
removed
in
Step
4.
Step 9:Change the hinge
axis� from
the
right
leftdoor
hole(see
chartĺ4)
Step 12:Revolve
the hinge
axis
on
bottomto
of the
to the left hole,see
Chart
5 thehole
ĸ Wooden Shelf Made of Beech
chart 7.
6.
On Panel
bottom
Ĺ
Control
edge of door, transfer door stop bracket
and
� Glass
Doorbushing to holes on opposite side. See Fig. 6.
�7.
Control
of Lampof
OnSwitch
top edge
door, transfer the button plugs and
� Adjustment
Leg to hole on opposite side. See Fig. 7.
bushing
Door Reversal Instructions:
You
reverse
the door LH
swing
if you change
the position
of the hinge(�)
8.canPlace
bottom
corner
of door
onto lower
hinge,,pls
follow the
steps
below:
then install top hinge to cabinet. Make sure door
Step 1:Close the door and use the knife carefully to remove the parts�ǃ�(see
is level and it seals properly against cabinet, then
chart 1)
securely
three screws.
Step 2:Remove
thefasten
hinge coverĹ(see
chart 1) See Fig. 7. Snap top
Step 3:Remove
the onto
screws hinge.
by cross-screwdriverĺ(see chart 1)
cap back
Step
Step 4:Remove the top hingeĻ(see chart 1)
Step 5:Remove the bolt by screwdriverļ(see chart 1)
ĸ
ķButton plugs
Ĺ
Top cap
ĺ
Screws
Move pin
to
ŋ
opposite hole
(upper and
lower hinges)
ĸ
Fig. 4
Ŀ
Chart 7
Step 13:Assemble the door on the bottom hinge�ˈthen reset the door bolt�
Chart 1
Step 6:Open the door and lift it up carefully then remove it,see chart 2.
ŀ
ĺ
Chart 5- 9 -
Chart 4
10:Use knife to remove the parts�,see chart 5.
Chart 6
Step 12:Revolve the hinge axis on the bottom of the door to the left hole,see
-8chart 7.
Screws
ŋ
Fig. 5
Button plugs
Hinge
Ļ
Bushing
ļ
ļ
Chart 6
Step 12:Revolve the hinge axis on the bottom of the door to the left hole,see
Chart 7
chart 7.
Step 13:Assemble the door on the bottom hinge�ˈthen reset the door bolt�
-9-
ŋ
5
Chart 7
Step 13:Assemble the door on the bottom hinge�ˈthen reset the door bolt�
International or other national or regional standards:
UL 250 BULLETINS-2003 U.S.A. household fridge safety requirements
IEC 61000-3-4-1998
ENERGY SAVING TIPS
Electromagnetic compatibility (EMC) - Limits -
FEATURES
Limitation of emission of harmonic currents in low-voltage power supply
systems for equipment with rated current greater than 16 A
• Install the wine cooler in the coolest part of a dry and
Adjustable Interior Shelves
U.S.A. household fridge safety
ventilated room, out of direct sunlight and away from UL 250 BULLETINS2-2003
Multi-position
adjustable
interior
shelves can be moved
heating ducts or registers. Do not place the wine
requirements
to
any
position
for
larger
or
smaller
bottles. The shipping
cooler next to heat-producing appliances such as aEnterprise Standard
spacers
that
stabilize
the
shelves
for
shipping should be
range, oven or dishwasher.
removed
and
discarded.
Q/MB 004-2007
Wine Cooler
• Level the wine cooler so the door closes tightly.
Interior Light (Some models)
• Do not overcrowd the wine cooler or block cold air
The light comes on automatically when the door is
vents. Doing so causes the wine cooler to run longer
opened. To replace the light bulb, turn the temperature
and use more energy. Shelves should not be lined
control to OFF and unplug the electrical cord. Replace the
with aluminum foil, wax paper or paper toweling.
old bulb with a bulb of the same wattage.
Liners interfere with cold air circulation, making the
wine cooler less efficient.
Know About Wine Cooler
ķ
1
• Wipe bottles and containers dry before placing them
in the wine cooler. This cuts down on moisture buildup inside the unit.
2
ĸ
• Organize the wine cooler to reduce door openings.
Remove as many items as needed at one time and
close the door as soon as possible.
3
Ĺ
ĺ
4
TEMPERATURE CONTROLS
Cool Down Period
5Ļ
For best performance, allow 4 hours for the wine cooler
to cool down completely. The wine cooler will run
continuously for the first several hours.
Temperature Control
ļ
6
1
Lamp assembly
Fig. 1
Glassfrom
door
The illustration might be2 different
the actual products.
• Adjust temperature gradually: move the knob in small
increments, allowing the temperature to stabilize.
3
Steel wire racks
• For colder temperatures, turn the knob towards
Colder.
4
- 6 - knob
Temperature
5
Lamp control switch
6
Adjustable leg
• For warmer temperatures, turn the knob towards
Cold.
The temperature range MIN and MAX is 41° - 64° F,
which is ideal for wine storage.
Note that by turning the temperature control knob to
OFF, it only stops the cooling cycle but does NOT turn off
the wine cooler.
If the wine cooler is unplugged from the power supply,
you must wait 3 to 5 minutes before restarting the wine
Cooler.
6
CARE AND CLEANING
WARNING
Before removing the light bulb, disconnect the wine
cooler from the power supply. Failure to do so could
result in electrical shock or personal injury.
1. Unplug power cord.
2. Remove the light bulb cover by gently pulling on the bottom end of the cover.Unscrew the bulb.
3. Replace with a 10 watt bulb of the same shape and
size.
4. Replace the light cover.
5. Plug power cord back in.
Cleaning the wine cooler
• Before cleaning, turn the temperature control to OFF, unplug the wine cooler and remove the bottles.
• Clean your wine cooler once every two months.
Inside: Wash inside surfaces of the wine cooler
with a solution of two tablespoons of baking soda in
one quart (1.136 litres) warm water. Rinse and dry.
Wring excess water out of the sponge or cloth when
cleaning in the area of the controls, or any electrical
parts.
Vacation and Moving Tips
Vacations:
If the wine cooler will not be used for several months:
• Remove all wine bottles and unplug the power cord.
• Clean and dry the interior thoroughly.
• Leave the wine cooler door open slightly, blocking it
open if necessary, to prevent odor and mold growth.
Moving: When moving the wine cooler, follow these
guidelines to prevent damage:
• Disconnect the power cord plug from the wall outlet.
• Remove wine bottles and clean the wine cooler.
• Secure all loose items by taping them securely in
place to prevent damage.
• In a moving vehicle, secure the wine cooler in an
upright position to prevent movement. Also, protect
the outside of the wine cooler with a blanket or
similar item.
WARNING
If leaving the wine cooler door open while on vacation,
make certain that children cannot get into the wine
cooler and become entrapped.
Wash the removable parts with the baking soda
solution mentioned above, or mild detergent and
warm water. Rinse and dry. Never use metallic
scouring pads, brushes, abrasive cleaners, or alkaline
solutions on any surface. Do not wash removable
parts in a dishwasher.
Outside: Wash the cabinet with warm water and
mild liquid detergent. Rinse well and wipe dry with a
clean soft cloth.
Care of plastic parts
• Be sure and protect the door gasket. It should be
kept clean at all times.
• If the plastic parts in the wine cooler remain
contaminated by oil (animal or vegetable) for a long period of time, they will age and crack easily. Please clean them on a regular basis.
7
Before You Call
1-800-944-9044 (United States)
Visit our web site at
www.frigidaire.com.
1-800-265-8352 (Canada)
PROBLEM
CAUSE
CORRECTION
WINE COOLER OPERATION
Wine Cooler does not
run.
•
•
•
•
•
Wine Cooler runs too
much or too long.
•
•
•
•
•
•
•
Wine cooler is plugged into a
circuit that has a ground fault
interrupt.
Temperature control is in the
OFF position.
Wine cooler may not be
plugged in, or plug may be
loose.
House fuse blown or tripped
circuit breaker.
Power outage.
•
Use another circuit. If you are unsure about the outlet,
have it checked by a certified technician.
•
See Setting the Temperature Control section.
•
Ensure plug is tightly pushed into outlet.
•
Check/replace fuse with a 15 amp time-delay fuse. Reset
circuit breaker.
Check house lights. Call local Electric Company.
Room or outside weather is
hot.
Wine Cooler has recently been
disconnected for a period of
time.
Large amounts of warm or hot
food has been stored recently.
Door is opened too frequently
or too long.
Wine Cooler door may be
slightly open.
Temperature control is set too
low.
Wine Cooler gasket is dirty,
worn, cracked, or poorly fitted.
•
•
•
•
•
•
•
•
It’s normal for the Wine Cooler to work harder under these
conditions.
It takes 4 hours for the Wine Cooler to cool down
completely.
Warm food will cause Wine Cooler to run more until the
desired temperature is reached.
Warm air entering the Wine Cooler causes it to run more.
Open doors less often.
See “DOOR PROBLEMS” section.
Turn control knob to a warmer setting. Allow several hours
for the temperature to stabilize.
Clean or change gasket. Leaks in the door seal will cause
Wine Cooler to run longer in order to maintain desired
temperature.
Interior Wine Cooler
temperature is too
cold.
•
Temperature control is set too
low.
•
Turn the control to a warmer setting. Allow several hours
for the temperature to stabilize.
Interior Wine Cooler
temperature is too
warm.
•
Temperature control is set too
warm.
Door is opened too frequently
or too long.
Door may not be seating
properly.
Large amounts of warm or hot
food has been stored recently.
Wine Cooler has recently been
disconnected for a period of
time.
•
Turn control to a colder setting. Allow several hours for the
temperature to stabilize.
Warm air entering the Wine Cooler causes it to run more.
Open doors less often.
See “DOOR PROBLEMS” section.
•
The external Wine Cooler walls
can be as much as 30°F warmer than room temperature.
•
This is normal while the compressor works to transfer heat
from inside the Wine Cooler cabinet.
•
Modern wine coolers have
increased storage capacity and
more stable temperatures.
They require a high efficiency
compressor
•
This is normal. When the surrounding noise level is low,
you might hear the compressor running while it cools the
interior.
•
•
•
•
Wine Cooler external
surface temperature is
warm.
•
•
•
•
Warm food will cause Wine Cooler to run more until the
desired temperature is reached.
It takes 4 hours for the Wine Cooler to cool down
completely.
SOUND AND NOISE
Louder sound levels
when wine cooler is
on.
8
Before You Call (continued)
PROBLEM
CAUSE
CORRECTION
SOUND AND NOISE (continued)
Longer sound levels
when compressor
comes on.
•
Wine Cooler operates at higher
pressures during the start of the
ON cycle.
•
This is normal. Sound will level off or disappear as wine
cooler continues to run.
Fan runs when room
temperature is below
45°.
•
Exterior thermostat has activated the heater or fan.
•
This is normal.
Popping or cracking
sound when compressor comes on.
•
Metal parts undergo expansion •
and contraction, as in hot water
pipes.
This is normal. Sound will level off or disappear as Wine
Cooler continues to run.
Boiling or gurgling
sound, like water boiling.
•
Refrigerant (used to cool Wine
Cooler) is circulating throughout the system.
•
This is normal.
Vibrating or rattling
noise.
•
Wine Cooler is not level. It
rocks on the floor when it is
moved slightly.
•
Level the unit. Refer to leveling instructions in the
“Installation” section.
Snapping sound.
•
Cold control turning the Wine
Cooler OFF and ON.
•
This is normal.
•
•
This is normal.
See “DOOR PROBLEMS” section.
•
Open the door less often.
WATER/MOISTURE/FROST INSIDE WINE COOLER
Moisture forms on
inside of Wine Cooler
walls.
•
•
•
Weather is hot and humid.
Door may not be seating
properly.
Door is kept open too long, or
opened too frequently.
WATER/MOISTURE/FROST OUTSIDE WINE COOLER
Moisture forms on outside of Wine Cooler.
•
Door may not be seating properly, causing the cold air from
inside the wine cooler to meet
warm moist air from outside.
•
See “DOOR PROBLEMS” section.
•
Interior needs to be cleaned.
•
Clean interior with sponge, warm water, and baking soda.
•
Wine Cooler is not level. It
rocks on the floor when it is
moved slightly.
•
This condition may force the cabinet out of square and
misalign the door. Refer to “Leveling’ in the “Installation”
section.
•
Light bulb is burnt out.
•
•
No electric current is reaching
the Wine Cooler.
•
Follow instructions under “Interior Light” in the
“Features” section.
See “Installation” section.
ODOR IN WINE COOLER
Odors in Wine Cooler.
DOOR PROBLEMS
Door will not close.
LIGHT BULB IS NOT ON
Light bulb is not on.
9
major appliance warranty
Major Appliance Warranty Information
Your appliance is covered by a one year limited warranty. For one year from your original date of
purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove
to be defective in materials or workmanship when such appliance is installed, used and maintained in
accordance with the provided instructions.
Exclusions
This warranty does not cover the following:
1.
Products with original serial numbers that have been removed, altered or cannot be readily determined.
2.
Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.
3.
Rust on the interior or exterior of the unit.
4.
Products purchased “as-is” are not covered by this warranty.
5.
Food loss due to any refrigerator or freezer failures.
6.
Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances
not in ordinary household use or used other than in accordance with the provided instructions.
8.
Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9.
Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,
etc.,which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or
knobs, handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors,
cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or
external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
DIScLAIMER Of IMpLIED WARRAntIES; LIMItAtIOn Of REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT
REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR
OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. ELECTROLUX SHALL NOT
BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL
EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED
WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE
LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
If You Need
Service
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone
numbers below.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp.
Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under
this warranty must be performed by Electrolux or an authorized service company. Product features or specifications as described
or illustrated are subject to change without notice.
uSA
1.800.944.9044
Electrolux Major Appliances
North America
P.O. Box 212378
Augusta, GA 30907
10
Canada
1.800.265.8352
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4