Owner`s manual | Frigidaire FASE7074NA Washer/Dryer User Manual

YF00647-120
DIGITAL CAMERA
FINEPIX F80EXR
EN
Before You Begin
First Steps
Owner’s Manual
Thank you for your purchase
of this product. This manual
describes how to use your
FUJIFILM FinePix F80EXR digital
camera and the supplied
software. Be sure that you
have read and understood
its contents before using the
camera.
Basic Photography and Playback
More on Photography
More on Playback
Movies
Connections
Menus
For information on related products, visit our website at
http://www.fujifilm.com/products/digital_cameras/index html
Technical Notes
Troubleshooting
Appendix
Notes and Cautions
IMPORTANT SAFETY INSTRUCTIONS
• Read Instructions: All the safety
and operating instructions should
be read before the appliance is
operated.
• Retain Instructions: The safety and
operating instructions should be
retained for future reference.
• Heed Warnings: All warnings on the
appliance and in the operating
instructions should be adhered to.
• Follow Instructions: All operating
and use instructions should be
followed.
Installation
Power Sources: This video product
should be operated only from the
type of power source indicated on
the marking label. If you are not sure
of the type of power supply to your
home, consult your appliance dealer
or local power company. For video
products intended to operate from
battery power, or other sources,
refer to the operating instructions.
your obsolete outlet. Do not defeat
the safety purpose of the polarized
plug.
Alternate Warnings: This video
product is equipped with a 3-wire
grounding-type plug, a plug having
a third (grounding) pin. This plug
will only fit into a grounding-type
power outlet. This is a safety feature.
If you are unable to insert the
plug into the outlet, contact your
electrician to replace your obsolete
outlet. Do not defeat the safety
purpose of the grounding-type
plug.
manufacturer’s instructions have
been adhered to.
This video product should never
be placed near or over a radiator or
heat register.
Attachments: Do not use
attachments not recommended by
the video product manufacturer as
they may cause hazards.
Water and Moisture: Do not use this
video product near water – for
example, near a bath tub, wash
bowl, kitchen sink, or laundry
tub, in a wet basement, or near a
swimming pool, and the like.
of the appliance should follow the
manufacturer’s instructions, and
should use a mounting accessory
recommended by the manufacturer.
An appliance and
cart combination
should be moved
with care. Quick
stops, excessive
force, and uneven
surfaces may
cause the appliance and cart
combination to overturn.
Antennas
Outdoor Antenna Grounding: If an
Overloading: Do not overload wall
Power-Cord Protection: Power-Supply outside antenna or cable system is
outlets and extension cords as this
connected to the video product, be
cords should be routed so that
can result in a risk of fire or electric
sure the antenna or cable system
they are not likely to be walked
shock.
is grounded so as to provide some
on or pinched by items placed
protection against voltage surges and
upon or against them, paying
Ventilation: Slots and openings
built-up static charges. Section 810
particular attention to cords at
in the cabinet are provided for
plugs, convenience receptacles, and of the National Electrical Code, ANSI/
ventilation and to ensure reliable
NFPA No. 70, provides information
the point where they exit from the
operation of the video product
with respect to proper grounding of
appliance.
and to protect it from overheating,
Grounding or Polarization: This
the mast and supporting structure,
and these openings must not be
Accessories:
Do
not
place
this
video
video product is equipped with a
grounding of the lead-in wire to
blocked or covered.
product
on
an
unstable
cart,
stand,
polarized alternating-current line
an antennadischarge unit, size of
The openings should never be
tripod,
bracket,
or
table.
The
video
plug (a plug having one blade
grounding conductors, location of
blocked by placing the video
product
may
fall,
causing
serious
wider than the other). This plug will product on a bed, sofa, rug, or other
antenna-discharge unit, connection
injury to a child or adult, and
fit into the power outlet only one
to grounding electrodes, and
similar surface.
serious damage to the appliance.
way. This is a safety feature. If you
requirements for the grounding
This video product should not
Use only with a cart, stand, tripod,
are unable to insert the plug fully
electrode.
be placed in a built-in installation
bracket, or table recommended
into the outlet, try reversing the
such as a bookcase or rack unless
plug. If the plug should still fail to fit, proper ventilation is provided or the by the manufacturer, or sold with
the video product. Any mounting
contact your electrician to replace
ii
Notes and Cautions
Power Lines: An outside antenna
system should not be located in the
vicinity of overhead power lines or
other electric light or power circuits,
or where it can fall into such power
lines or circuits. When installing an
outside antenna system, extreme
care should be taken to keep from
touching such power lines or
circuits as contact with them might
be fatal.
EXAMPLE OF ANTENNA GROUNDING AS
PER NATIONAL ELECTRICAL CODE
Ground
Clamp
Electric
Service
Equipment
Ground
Clamps
Power Service Grounding
Electrode System
(NEC ART 250. PART H)
Never spill liquid of any kind on the
video product.
Lightning: For added protection for
this video product receiver during
a lightning storm, or when it is left
unattended and unused for long
periods of time, unplug it from
the wall outlet and disconnect
the antenna or cable system. This
will prevent damage to the video
product due to lightning and
power-line surges.
Service
Antenna Lead
Servicing: Do not attempt to service
in Wire
this video product yourself as
opening or removing covers may
Antenna
expose you to dangerous voltage or
Discharge Unit other hazards. Refer all servicing to
(NEC SECTION
qualified service personnel.
810-20)
Grounding
Damage Requiring Service: Unplug this
Conductors
video product from the wall outlet
(NEC SECTION
and refer servicing to qualified
810-21)
service personnel under the
following conditions:
When the power-supply cord or
Use
Cleaning: Unplug this video product plug is damaged.
from the wall outlet before cleaning. If liquid has been spilled, or objects
Do not use liquid cleaners or aerosol have fallen into the video product.
If the video product has been
cleaners. Use a damp cloth for
exposed to rain or water.
cleaning.
If the video product has been
Object and Liquid Entry: Never push
dropped or the cabinet has been
objects of any kind into this video
damaged.
product through openings as they
If the video product does not
may touch dangerous voltage
operate normally be following the
points or shortout parts that could
operating instructions. Adjust only
result in a fire or electric shock.
those controls that are covered
by the operating instructions as
an improper adjustment of other
controls may result in damage and
will often require extensive work
by a qualified technician to restore
the video product to its normal
operation.
When the video product exhibits
a distinct change in performance
- this indicates a need for service.
Replacement Parts: When
replacement parts are required, be
sure the service technician has used
replacement parts specified by the
manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may
result in fire, electric shock or other
hazards.
Safety Check: Upon completion of
any service or repairs to this video
product, ask the service technician
to perform safety checks to
determine that the video product is
in proper operating condition.
iii
Notes and Cautions
Be sure to read this notes before using
WARNING
Safety Notes
If a problem arises, turn the camera off, remove the battery, disconnect and unplug
the AC power adapter.
Continued use of the camera when it is emitting smoke, is emitting any
unusual odor, or is in any other abnormal state can cause a fire or electric
shock.
• Contact your FUJIFILM dealer.
• Make sure that you use your camera correctly. Read these Safety Notes
and your Owner’s Manual carefully before use.
• After reading these Safety Notes, store them in a safe place.
Unplug
from power
socket
About the Icons
• The icons shown below are used in this document to indicate the
severity of the injury or damage that can result if the information
indicated by the icon is ignored and the product is used incorrectly as a
result.
WARNING
CAUTION
This icon indicates that death or serious injury can result if the information
is ignored.
Do not allow water or foreign objects to enter the camera.
If water or foreign objects get inside the camera, turn the camera off, remove
the battery and disconnect and unplug the AC power adapter.
Continued use of the camera can cause a fire or electric shock.
• Contact your FUJIFILM dealer.
Do not use in
the bathroom
or shower
This icon indicates that personal injury or material damage can result if the
information is ignored.
Do not
disassemble
The icons shown below are used to indicate the nature of the information
which is to be observed.
Triangular icons tell you that this information requires attention (“important”).
Circular icons with a diagonal bar tell you that the action indicated is
prohibited (“Prohibited ).
Filled circles with an exclamation mark tell you an action that must be
performed (“Required”).
Do not use the camera in the bathroom or shower.
This can cause a fire or electric shock.
Never attempt to change or take apart the camera. (Never open the casing.) Do not use
the camera when it has been dropped or the casing is damaged.
This can cause a fire or electric shock.
• Contact your FUJIFILM dealer.
Do not change, heat or unduly twist or pull the connection cord and do not place heavy
objects on the connection cord.
These actions could damage the cord and cause a fire or electric shock.
• If the cord is damaged, contact your FUJIFILM dealer.
Do not place the camera on an unstable surface.
This can cause the camera to fall or tip over and cause injury.
Never attempt to take pictures while in motion.
Do not use the camera while you are walking or driving a vehicle. This can
result in you falling down or being involved in a traffic accident.
Do not touch any metal parts of the camera during a thunderstorm.
This can cause an electric shock due to induced current from the lightning
discharge.
Do not use the battery except as specified.
Load the battery as aligned with the indicator.
iv
Notes and Cautions
WARNING
CAUTION
Do not heat, change or take apart the battery. Do not drop or subject the battery to
impacts. Do not store the battery with metallic products. Do not use chargers other
than the specified model to charge the battery.
Any of these actions can cause the battery to burst or leak and cause fire or
injury as a result.
Keep out of the reach of small children.
This product could cause injury in the hands of a child.
Use only the battery or AC power adapters specified for use with this camera. Do not
use voltages other than the power supply voltage shown.
The use of other power sources can cause a fire.
Do not move the camera while the AC power adapter is still connected. Do not pull on
the connection cord to disconnect the AC power adapter.
This can damage the power cord or cables and cause a fire or electric shock.
If the battery leaks and fluid gets in contact with your eyes, skin or clothing. Flush
the affected area with clean water and seek medical attention or call an emergency
number right away.
Do not use the AC power adapter when the plug is damaged or the plug socket
connection is loose.
This could cause a fire or electric shock.
Do not use the charger to charge batteries other than those specified here.
The Ni-MH battery charger is designed for Fujifilm HR-AA Ni-MH batteries.
Using the charger to charge conventional batteries or other types of
rechargeable batteries can cause the battery to leak fluid, overheat or burst.
Do not cover or wrap the camera or the AC power adapter in a cloth or blanket.
This can cause heat to build up and distort the casing or cause a fire.
When carrying the battery, install it in a digital camera or keep it in the hard case.
When storing the battery, keep it in the hard case. When discarding, cover the battery
terminals with insulation tape.
Contact with other metallic objects or battery could cause the battery to
ignite or burst.
Keep Memory Cards out of the reach of small children.
Because Memory Cards are small, they can be swallowed by children. Be sure
to store Memory Cards out of the reach of small children. If a child swallows a
Memory Card, seek medical attention or call an emergency number.
CAUTION
Do not use this camera in locations affected by oil fumes, steam, humidity or dust.
This can cause a fire or electric shock.
Do not place heavy objects on the camera.
This can cause the heavy object to tip over or fall and cause injury.
When you are cleaning the camera or you do not plan to use the camera for an extended
period, remove the battery and disconnect and unplug the AC power adapter.
Failure to do so can cause a fire or electric shock.
When charging ends, unplug the charger from the power socket.
Leaving the charger plugged into the power socket can cause a fire.
Using a flash too close to a person’s eyes may temporarily affect the eyesight.
Take particular care when photographing infants and young children.
When an xD-Picture Card is removed, the card could come out of the slot too quickly.
Use your finger to hold it and gently release the card.
Request regular internal testing and cleaning for your camera.
Build-up of dust in your camera can cause a fire or electric shock.
• Contact your FUJIFILM dealer to request internal cleaning every 2 years.
• Please note this is not a free of charge service.
Do not leave this camera in places subject to extremely high temperatures.
Do not leave the camera in locations such as a sealed vehicle or in direct
sunlight. This can cause a fire.
v
Notes and Cautions
Power Supply and Battery
* Confirm your battery type before reading
the following descriptions.
The following explains proper use
of batteries and how to prolong
their life. Incorrect use of batteries
can cause shorter battery life, as
well as leakage, excessive heat, fire
or explosion.
take care not to place the battery
directly against the pad. The
camera may not operate if you
use a depleted battery in cold
conditions.
■ Charging the Battery
• You can charge the battery using
the battery charger (included).
• The battery can be charged at
ambient temperatures between
1 Camera uses the Rechargeable
0°C and +40°C (+32°F and
Lithium-ion Battery
+104°F). Refer to the OWNER’S
* When shipped, the battery is not
MANUAL for the time of
fully charged. Always charge the
charging battery.
battery before using it.
• You should charge the battery
* When carrying the battery, install
at an ambient temperature
it in a digital camera or keep it in
between +10°C and +35°C
the soft case.
(+50°F and +95°F). If you charge
■ Battery Features
the battery at a temperature
• The battery gradually loses its
outside this range, charging
charge even when not used. Use
takes longer because the
a battery that has been charged
performance of the battery is
recently (in the last day or two) to
impaired.
take pictures.
• You cannot charge the battery
• To maximize the life of the battery,
at temperatures of 0°C (+32°F) or
turn the camera off as quickly as
below.
possible when it is not being used. • The Rechargeable Lithium-ion
• The number of available frames
Battery does not need to be fully
will be lower in cold locations or
discharged or exhausted flat
at low temperatures. Take along
before being charged.
a spare fully charged battery. You
• The battery may feel warm after it
can also increase the amount of
has been charged or immediately
power produced by putting the
after being used. This is perfectly
battery in your pocket or another
normal.
warm place to heat it and then
• Do not recharge a fully charged
loading it into the camera just
battery.
before you take a picture.
If you are using a heating pad,
vi
■ Battery Life
At normal temperatures, the battery
can be used at least 300 times.
If the time for which the battery
provides power shortens markedly,
this indicates that the battery has
reached the end of its effective life
and should be replaced.
■ Notes on storage
• If a battery is stored for long
periods while charged, the
performance of the battery can
be impaired. If the battery will not
be used for some time, run the
battery out before storing it.
• If you do not intend to use the
camera for a long period of time,
remove the battery from the
camera.
• Store the battery in a cool place.
• The battery should be stored in
a dry location with an ambient
temperature between +15°C and
+25°C (+59°F and +77°F).
• Do not leave the battery in hot
or extremely cold places.
• Dispose of used battery promptly.
• Do not drop the battery or
otherwise subject it to strong
impacts.
• Do not expose the battery to
water.
• Always keep the battery terminals
clean.
• Do not store batteries in hot
places. Also, if you use the battery
for a long period, the camera body
and the battery itself will become
warm. This is normal. Use the AC
power adapter if you are taking
pictures or viewing images for a
long period of time.
2 Camera uses AA-size alkaline
or Ni-MH (nickelmetal hydride)
rechargeable batteries
* For details on the batteries that
you can use, refer to the OWNER’S
MANUAL of your camera.
■ Cautions for Using Battey
• Do not heat the batteries or throw
them into a fire.
• Do not carry or store batteries
■ Handling the Battery
with metal objects such as
Cautions for Your Safety:
necklaces or hairpins.
• Do not carry or store battery with • Do not expose the batteries to
metal objects such as necklaces or
water, and keep batteries from
hairpins.
getting wet or stored in moist
• Do not heat the battery or throw it
locations.
into a fire.
• Do not attempt to take apart or
• Do not attempt to take apart or
change the batteries, including
change the battery.
battery casings.
• Do not recharge the battery with
• Do not subject the batteries to
chargers other those specified.
strong impacts.
Notes and Cautions
• Do not use batteries that are
If any liquid at all leaks from
leaking, deformed, discolored.
the batteries, wipe the battery
• Do not store batteries in warm or
compartment thoroughly and
humid places.
then load new batteries.
• Keep the batteries out of reach of
If any battery fluid comes
babies and small children.
into contact with your hands
• Make sure that the battery polarity
or clothing, flush the area
(E and F) is correct.
thoroughly with water. Note
• Do not use new with used
that battery fluid can cause
batteries. Do not use charged and
loss of eyesight if it gets into
discharged batteries together.
your eyes. If this occurs, do
• Do not use different types or
not rub your eyes. Flush the
brands of batteries at the same
fluid out with clean water and
time.
contact your physician for
• If you do not intend to use the
treatment.
camera for a long period of time,
remove the batteries from the
■ Using the AA-size Ni-MH batteries
camera. Note if the camera is left
correctly
with the batteries removed, the
• Ni-MH batteries left unused in
time and date settings are cleared.
storage for long periods can
• The batteries feel warm right after
become “deactivated”. Also,
being used. Before removing the
repeatedly charging Ni-MH
batteries, turn the camera off
batteries that are only partially
and wait for the batteries to cool
discharged can cause them
down.
to suffer from the “memory
• Since batteries do not work well in
effect”. Ni-MH batteries that
cold weather or locations, warm
are “deactivated” or affected by
the batteries by placing them
“memory” suffer from the problem
inside your garments before use.
of only providing power for a
Batteries do not work well when
short time after being charged. To
cold. They will work again when
prevent this problem, discharge
the temperature returns to normal.
and recharge them several times
• Soil (such as fingerprints) on
using the camera’s “Discharging
the battery terminals makes the
rechargeable batteries” function.
batteries charge less reducing the
Deactivation and memory are
number of images. Carefully wipe
specific to Ni-MH batteries and are
the battery terminals with a soft
not in fact battery faults.
dry cloth before loading.
See OWNER’S MANUAL for the
procedure for “Discharging
rechargeable batteries”.
CAUTION
Do not use the “Discharging
rechargeable batteries” function
when alkaline batteries being used.
• To charge Ni-MH batteries,
use the quick battery charger
(sold separately). Refer to the
instructions supplied with the
charger to make sure that the
charger is used correctly.
• Do not use the battery charger to
charge other batteries.
• Note that the batteries feel warm
after being charged.
• Due to the way the camera is
constructed, a small amount of
current is used even when the
camera is turned off. Note in
particular that leaving Ni-MH
batteries in the camera for a long
period will overdischarge the
batteries and may render them
unusable even after recharging.
• Ni-MH batteries will self-discharge
even when not used, and the time
for which they can be used may
be shortened as a result.
• Ni-MH batteries will deteriorate
rapidly if overdischarged (e.g.
by discharging the batteries in a
flashlight). Use the “Discharging
rechargeable batteries” function
provided in the camera to
discharge the batteries.
• Ni-MH batteries have a limited
service life. If a battery can only be
used for a short time even after
repeated discharge-charge cycles,
it may have reached the end of its
service life.
■ Disposing of Batteries
• When disposing of batteries, do
so in accordance with your local
waste disposal regulations.
3 Notes on both models ( 1 , 2 )
■ AC Power Adapter
Always use the AC Power Adapter
with the camera. The use of an AC
Power adapter other than FUJIFILM
AC Power Adapter can be damaged
to your digital camera.
For details on the AC power adapter,
refer to the OWNER’S MANUAL of
your camera.
• Use the AC power adapter for
indoor use only.
• Plug the connection cord plug
securely into the DC input
terminal.
• Turn off the FUJIFILM Digital
camera before disconnecting the
cord from the DC input terminal.
To disconnect, pull out the plug
gently. Do not pull on the cord.
• Do not use the AC power adapter
with any device other than your
camera.
• During use, the AC power adapter
will become hot to the touch. This
is normal.
vii
Notes and Cautions
• Do not take apart the AC power
adapter. Doing so could be
dangerous.
• Do not use the AC power adapter
in a hot and humid place.
• Do not subject the AC power
adapter to strong shocks.
• The AC power adapter may emit a
humming. This is normal.
• If used near a radio, the AC power
adapter may cause static. If this
happens, move the camera away
from the radio.
purely for personal use. Users are
also asked to note that the transfer
of Memory Card containing images
or data protected under copyright
laws is only permissible within
the restrictions imposed by those
copyright laws.
• IBM PC/AT is a registered
trademark of International
Business Machines Corp. of the
U.S.A.
• Macintosh, Quick-Time, and Mac
OS are trademarks of Apple Inc. in
the U.S.A. and other countries.
• Windows 7, Windows Vista and the
■ Handling Your Digital Camera
Windows logo are trademarks of
To ensure that images are recorded
the Microsoft group of companies.
correctly, do not subject the camera
• IrSimple™ Trademark is owned by
to impact or shock while an image is
the Infrared Data Association®.
being recorded.
• IrSS™ Trademark or IrSimpleShot™
■ Liquid Crystal
Trademark is owned by the
Before Using the Camera
If the LCD monitor is damaged,
Infrared Data Association®.
take
particular
care
with
the
liquid
•
SDHC logo is a trademark.
■ Test Shots Prior to Photography
crystal
in
the
monitor.
If
any
of
the
•
HDMI logo is a trademark.
For important photographs (such
following situations arise, take the
• YouTube is a trademark of Google
as weddings and overseas trips),
Inc.
always take a test shot and view the urgent action indicated.
• Other company or product names
image to make sure that the camera • If liquid crystal comes in contact
with your skin:
are trademarks or registered
is working normally.
Wipe the area with a cloth and
trademarks of the respective
• FUJIFILM Corporation cannot
then wash thoroughly with soap
companies.
accept liability for any incidental
and running water.
losses (such as the costs of
■ Notes on Electrical Interference
photography or the loss of income • If liquid crystal gets into your eye: If the camera is to be used in
Flush the affected eye with clean
from photography) incurred as a
hospitals or aircrafts, please
water for at least 15 minutes and
result of faults with this product.
note that this camera may cause
then seek medical assistance.
interference to other equipment in
■ Notes on Copyright
• If liquid crystal is swallowed:
the hospital or aircraft. For details,
Images recorded using your digital
Flush your mouth thoroughly with
please check with the applicable
camera system cannot be used in
water. Drink large quantities of
regulations.
ways that infringe copyright laws
water and induce vomiting. Then
without the consent of the owner,
seek medical assistance.
unless intended only for personal
■ Trademark Information
use. Note that some restrictions
•
and xD-Picture Card™
apply to the photographing of
are trademarks of FUJIFILM
stage performances, entertainments
Corporation.
and exhibits, even when intended
viii
■ Explanation of Color Television
System
NTSC: National Television System
Committee, color television
telecasting specifications
adopted mainly in the U.S.A.,
Canada and Japan.
PAL: Phase Alternation by Line,
a color television system
adopted mainly by European
countries and China.
■ Exif Print (Exif ver. 2.2)
Exif Print Format is a newly revised
digital camera file format that
contains a variety of shooting
information for optimal printing.
About This Manual
Before using the camera, read this manual and the warnings on the Basic Manual. For information on
specific topics, consult the sources below.
✔ Camera Q & A .....................................................pg.
..................................................... pg. x
Know what you want to do but don’t know the
name for it? Find the answer in “Camera Q & A.”
✔ Table of Contents ............................................
............................................pg.
pg. xiii
The “Table of Contents” gives an overview of the
entire manual. The principal camera operations
are listed here.
✔ Troubleshooting ...
............................................pg.
... ... ... ... ... ... ... ... ... ... pg. 105
Having a specific problem with the camera?
Find the answer here.
✔ Warning Messages and Displays ..................... pg. 114
Find out what’s behind that flashing icon or
error message in the monitor or electronic
viewfinder.
✔ Glossary ........................................................
... ... ... ... ... ... ... ... ... ... ... ... ... ... pg.
pg 118
The meanings of some technical terms may be
found here.
✔ Restrictions on Camera Settings
See the Basic Manual for restrictions on the
options available in each shooting mode.
Memory Cards
Pictures can be stored in the camera’s internal memory or on optional SD and SDHC memory cards. In this
manual, SD memory cards are referred to as “memory cards.” For more information, see page 8.
ix
Camera Q & A
Find items by task.
Camera Setup
Question
How do I set the camera clock?
Can I set the clock to local time when I travel?
How do I keep the display from turning off automatically?
How do I make the display brighter or darker?
How do I stop the camera beeping and clicking?
Can I change the sound the shutter makes?
What are the parts of the camera called?
What do the icons in the display mean?
How do I use the menus?
What’s behind that flashing icon or error message?
How much charge is left in the battery?
Key phrase
See page
Date and time
12
Time difference
96
Auto power off
99
LCD brightness
99
Operation and shutter volume
94
Silent mode
19
Shutter sound
94
Parts of the camera
2
Displays
3
Menus
65
Messages and displays
114
Battery level
14
Sharing Pictures
Question
Can I print pictures on my home printer?
Can I copy my pictures to my computer?
x
Key phrase
See page
Printing pictures
54
Viewing pictures on a computer
59
Camera Q & A
Taking Pictures
Question
How many pictures can I take?
Is there a quick and easy way to take snapshots?
How can I avoid blurred pictures?
How can I make good portraits?
Can I choose my own settings for different scenes?
Can the camera automatically adjust settings for different scenes?
Can I choose between clarity, reduced noise, and dynamic range?
How can I take good pictures of dogs or cats?
Can I prioritize to focus the specified person’s face?
How do I shoot close-ups?
How do I keep the flash from firing?
How do I stop my subjects’ eyes glowing red when I use the flash?
How do I “fill-in” shadows on back-lit subjects?
How do I take a series of pictures in a single burst?
How do I turn off the lamp on the front of the camera?
How do I take a group portrait that includes the photographer?
How do I frame pictures with the subject off to one side?
Can I choose shutter speed and aperture?
How do I adjust exposure?
How do I simulate the effects of different types of film?
How do I keep a moving subject in focus?
How do I shoot movies?
Key phrase
Memory capacity
k mode
Dual IS mode
Intelligent Face Detection
Scene position
r mode
s, t, and u modes
Y DOG/T CAT
FACE RECOGNITION
Close-ups (macro mode)
See page
119
21
17
30
23
14
21
25
76
36
Flash mode
37
Continuous shooting mode
AF-assist illuminator
Self-timer mode
Focus lock
P and M modes
Exposure compensation
Film simulation
Tracking
Recording movies
74
34
39
32
27, 28
35
68
76
48
xi
Camera Q & A
Viewing Pictures
Question
How do I view my pictures?
How do I delete the current picture?
Can I select other pictures for deletion?
Can I zoom in on pictures during playback?
How do I view a lot of pictures at once?
How do I find pictures?
Can I protect my pictures from accidental deletion?
Can I hide the icons in the display when viewing my pictures?
Can I view my pictures in a slide show?
Can I add a short voice memo to my pictures?
Can I crop unwanted elements out of my pictures?
Can I make small copies of pictures?
Can I copy pictures from internal memory to a memory card?
How do I view my pictures on TV?
xii
Key phrase
Single-frame playback
The I button
Deleting pictures
Playback zoom
Multi-frame playback
Image search
Protect
Choosing a display format
Slide show
Voice memo
Crop
Resize
Copy
Viewing pictures on TV
See page
41
20
46
42
43
44
85
41
82
90
86
87
89
52
Table of Contents
Notes and Cautions ........................................................................ ii
IMPORTANT SAFETY INSTRUCTIONS ...................................... ii
Safety Notes .................................................................................... iv
About This Manual ......................................................................... ix
Camera Q & A ..................................................................................... x
Before You Begi
Begin
n
Introduction....................................................................................... 1
Symbols and Conventions .......................................................... 1
Supplied Accessories .................................................................... 1
Parts of the Camera ....................................................................... 2
Camera Displays .......................................................................... 3
The Mode Dial .............................................................................. 4
First Steps
Steps
Charging the Battery ..................................................................... 5
Inserting the Battery...................................................................... 6
Inserting a Memory Card ............................................................. 8
Turning the Camera on and off ............................................... 11
Shooting Mode ............................................................................. 11
Playback Mode .............................................................................. 11
Basic Setup .......................................................................................12
Basic Photography and Playbac
Playback
k
Taking Pictures in r (P AUTO) Mode .....................14
Viewing Pictures ............................................................................20
More on Photography
Photography
Shooting Mode ...............................................................................21
k AUTO ..........................................................................................21
O EXR ......................................................................................21
A NATURAL & K .......................................................................22
B NATURAL LIGHT ...................................................................23
SP SCENE POSITION ....................................................................23
M MANUAL .....................................................................................27
P PROGRAM AE/A APERTURE PRIORITY AE........................28
B Intelligent Face Detection ..................................................30
Focus Lock ........................................................................................32
5 Exposure Compensation.....................................................35
L Macro Mode (Close-ups) ......................................................36
K Using the Flash (Super Intelligent Flash) .......................37
J Using the Self-Timer...............................................................39
More on Playback
Playback
Playback Options...........................................................................41
Playback Zoom..............................................................................42
Multi-Frame Playback.................................................................43
V Image Search ............................................................................44
Image Search based on categories .......................................44
Using Playback Menu with Image Search...........................45
M Deleting Pictures ....................................................................46
Moviess
Movie
A Recording Movies ...................................................................48
D Viewing Movies .......................................................................51
Connectionss
Connection
Viewing Pictures on TV ...............................................................52
Printing Pictures via USB ...........................................................54
Connecting the Camera ............................................................54
Printing Selected Pictures ........................................................54
Printing the DPOF Print Order ................................................56
Creating a DPOF Print Order ....................................................57
xiii
Table of Contents
Viewing Pictures on a Computer............................................59
Installing the Software...............................................................59
Connecting the Camera ............................................................63
Menuss
Menu
Using the Menus: Shooting Mode .........................................65
Using the v-Mode Menu .........................................................65
v-Mode Menu Options ............................................................66
n ISO ............................................................................................67
o IMAGE SIZE ...........................................................................67
W FILM SIMULATION ..............................................................68
Using the Shooting Menu.........................................................69
Shooting Menu Options ............................................................70
T IMAGE QUALITY ..................................................................72
U DYNAMIC RANGE ...............................................................72
C WHITE BALANCE .................................................................72
E CONTINUOUS ......................................................................74
B PHOTOMETRY ......................................................................75
F AF MODE ...............................................................................75
S FACE RECOGNITION...........................................................76
Using the Menus: Playback Mode ..........................................81
Using the v-Mode Menu .........................................................81
v-Mode Menu Options ............................................................81
q SLIDE SHOW .........................................................................82
Using the Playback Menu .........................................................83
Playback Menu Options.............................................................84
a RED EYE REMOVAL.............................................................85
O PROTECT ................................................................................85
R CROP .......................................................................................86
j RESIZE .....................................................................................87
N IMAGE ROTATE ....................................................................88
xiv
P COPY .......................................................................................89
Q VOICE MEMO........................................................................90
S ERASE FACE RECOG. ..........................................................92
J DISP ASPECT .........................................................................92
The Setup Menu .............................................................................93
Using the Setup Menu ...............................................................93
Setup Menu Options...................................................................94
p TIME DIFFERENCE...............................................................96
m FORMAT .................................................................................97
a IMAGE DISP. ..........................................................................97
b FRAME NO. ............................................................................98
g PLAYBACK VOLUME...........................................................99
g LCD BRIGHTNESS................................................................99
o AUTO POWER OFF ..............................................................99
c DIGITAL ZOOM ................................................................. 100
m POWER MANAGEMENT ..................................................101
Technical Note
Notess
Optional Accessories ................................................................ 102
Accessories from FUJIFILM .................................................... 103
Caring for the Camera .............................................................. 104
Troubleshooting
Troubleshootin
g
Troubleshooting ......................................................................... 105
Warning Messages and Displays ..........................................114
Appendix
Appendi
x
Glossary ...........................................................................................118
Internal Memory/Memory Card Capacity ........................119
Specifications ................................................................................120
Introduction
Symbols and Conventions
Menus and other text in the camera monitor are shown in bold. In the illustrations in this manual, the
monitor display may be simplified for explanatory purposes.
Before You Begin
The following symbols are used in this manual:
C Caution: This information should be read before use to ensure correct operation.
A Note: Points to note when using the camera.
B Tip: Additional information that may be helpful when using the camera.
Supplied
p
Accessories
The following items are included with the camera:
CD-ROM
NP-50 rechargeable battery
BC-45W battery charger
Attaching the Strap
Attach the strap as shown.
USB cable
• Strap
• Owner’s Manual CD
(contains this manual)
• Basic Manual
A/V cable
1
Introduction
Parts of the Camera
For more information, refer to the page listed to the right of each item.
2
1
21
22
3
9
7
6
10
11
8
12
13
14
20
5
19
4
25
15
Selector button
Move cursor up E
l (exposure compensation)
button (pg. 35)
I (delete) button (pg. 20)
Move cursor left G
L (macro)
button (pg. 36)
Move cursor right H
K (flash) button
(pg. 37)
18 17 16
23
24
Move cursor down F
J (self-timer) button (pg. 39)
1 Shutter button ...........................................18 10 Indicator lamp ............................................19 18
2 n button ......................................... 11 11 Mode dial ........................................................ 4 19
3 AF-assist illuminator ...............................34 12 v (photo mode) button ............65, 81 20
Self-timer lamp ..........................................40 13 Strap eyelet .................................................... 1 21
4 Lens and lens cover
14 Terminal cover............................52, 54, 63
5 Microphone .................................................90 15 DC coupler cable cover..................... 103 22
6 Flash..................................................................37 16 B (Intelligent Face Detection)
23
7 Zoom control......................................16, 42
button .............................................................30 24
8 Monitor ............................................................. 3 17 DISP (display)/BACK button ...........17, 41 25
U (silent mode) button......................19
9 D (playback) button ............................41
2
MENU/OK button
(pg. 12)
Battery-chamber cover .......................... 6
Tripod mount
Speaker ...........................................................91
Connector for USB cable .............54, 63
Connector for A/V cable .....................52
HDMI connector .......................................52
Battery latch ............................................. 6, 7
Battery chamber ......................................... 6
Memory card slot ....................................... 9
Introduction
■ Shooting
*
19
800
F
AF
12 / 31 / 2050 10 : 00 AM
-1 2 3
250
F3.3
* d: indicates that no memory card
is inserted and that pictures will
be stored in the camera’s internal
memory (pg. 8).
1
2
3
4
5
6
7
8
9
10
11
12
Internal memory indicator*
Focus frame .................................................32
Silent mode indicator............................19
Continuous shooting mode .............74
Metering ........................................................75
Intelligent Face Detection indicator
.............................................................................30
Shooting mode .........................................21
Flash mode...................................................37
Macro (close-up) mode........................36
Self-timer indicator .................................39
Focus warning ...........................................18
Blur warning ................................................38
13
14
15
16
17
18
19
20
21
22
23
24
25
Date and time.............................................12
Shutter speed
Aperture
Image size .....................................................67
Number of available frames............119
Sensitivity ......................................................67
Image quality..............................................72
Dynamic range ..........................................72
Film simulation ..........................................68
White balance ............................................72
Battery level .................................................14
Dual IS mode ..............................................17
Exposure compensation .....................35
Before You Begin
Camera Displays
The following indicators may appear during shooting and playback: The indicators displayed vary
with camera settings.
■ Playback
100-0001
400
4:3 F
12 / 31 / 2050 10 : 00 AM
-1 2 3
1/250 F3.3
1 Intelligent Face Detection indicator
8 Gift image .....................................................41
.....................................................................30, 42 9 Red-eye removal indicator ................85
2 Playback mode indicator ............20, 41 10 Pro focus mode, Pro low-light mode
3 Protected image .......................................85
.............................................................................24
4 DPOF print indicator ..............................56 11 Frame number ...........................................98
5 Voice memo indicator...........................90 12 Dynamic range ..........................................72
6 Portrait enhancer .....................................26 13 P mode ..............................................21
7 Silent mode indicator............................19
3
Introduction
The Mode Dial
To select a shooting mode, align the mode icon with the mark next
to the mode dial.
P (PROGRAM AE): Select for full control over
all camera settings except shutter speed
(pg. 28). Choose between program and
aperture-priority AE.
O: Improve clarity, reduce noise,
increase dynamic range, or let the camera
automatically adjust settings to suit the
scene (pg. 21).
k (AUTO): A simple “point-and-shoot”
mode recommended for first-time users
of digital cameras (pg. 21).
M (MANUAL): Select for full control over
camera settings, including shutter speed
and aperture (pg. 27).
A (MOVIE): Record movies with sound
(pg. 48).
SP (SCENE POSITION): Choose a scene suited
to the subject or shooting conditions and
let the camera do the rest (pg. 23).
B (NATURAL LIGHT): Capture natural light
indoors, under low light, or where the
flash can not be used (pg. 23).
A (NATURAL & K): Helps ensure good results
in situations with difficult lighting. Each time
the shutter button is pressed, the camera
takes two shots: one shot without the flash to
preserve natural lighting, followed immediately
by a second shot with the flash (pg. 22).
4
Charging the Battery
The battery is not charged at shipment. Charge
the battery before use.
Batteries
The camera uses an NP-50 rechargeable battery.
charger as shown, making sure that the
battery is in the orientation indicated by the
F B E labels.
Battery
Charging
indicator
E
label
B
Battery charger
F
B
F
Arrow
Elabel
the charger in.
2 Plug
Plug the charger into a power outlet. The
charging indicator will light.
C Cautions
• Unplug the charger when it is not in use.
The Charging Indicator
The charging indicator shows battery charge status
as follows:
Charging indicator Battery status
Action
Battery not
Insert
inserted.
the battery.
Off
Battery fully
Remove
charged.
the battery.
On
Battery charging.
—
Unplug the
charger and
Blinks
Battery fault.
remove the
battery.
First Steps
the battery in the charger.
1 Place
Insert the battery into the supplied battery
• Remove dirt from the battery terminals with
a clean, dry cloth. Failure to observe this
precaution could prevent the battery from
charging.
• Charging times increase at low temperatures.
the battery.
3 Charge
Remove the battery when charging is
complete.
Charging time
See specifications of the battery charger (pg. 124).
5
Inserting the Battery
After charging the battery, insert it in the camera as described below.
1 Open the battery-chamber cover.
A Note
Be sure the camera is off before opening the
battery-chamber cover.
C Cautions
• Do not open the battery-chamber cover
when the camera is on. Failure to observe this
precaution could result in damage to image
files or memory cards.
• Do not use excessive force when handling the
battery-chamber cover.
Insert the battery.
2 Insert
the battery
with the terminals first
and the orange stripe
aligned with the orange
battery latch. Slide the
battery into the camera,
keeping the battery
latch pressed to one
side as shown below. Confirm that the
battery is securely latched.
Orange stripe
Battery latch
C Caution
Insert the battery in the correct orientation. Do
NOT use force or attempt to insert the battery
upside down or backwards. The battery will
slide in easily in the correct orientation.
6
Inserting the Battery
3 Close the battery-chamber cover.
Battery latch
C Caution
Turn the camera off before removing the battery.
First Steps
Removing the Battery
After turning the camera off, open the batterychamber cover, press the battery latch to the side,
and slide the battery out of the camera as shown.
B Tips: Using an AC Adapter
• The camera can be powered by an optional AC
adapter and DC coupler (sold separately). See
manuals provided with the AC adapter and DC
coupler for details.
• If the camera is powered by an AC adapter, demo
mode instructions will be displayed when the
camera is turned on. Selecting this option starts a
slide show. To cancel, press the shutter button.
C Cautions
• Do not affix stickers or other objects to the battery.
Failure to observe this precaution could make it
impossible to remove the battery from the camera.
• Do not short the battery terminals. The battery
could overheat.
• Use only battery chargers designated for use with
the battery. Failure to observe this precaution could
result in product malfunction.
• Do not remove the labels from the battery or
attempt to split or peel the outer casing.
• The battery gradually loses its charge when not in
use. Charge the battery one or two days before use.
7
Inserting a Memory Card
Although the camera can store pictures in internal memory, SD memory cards (sold separately) can
be used to store additional pictures.
When no memory card is inserted, d appears in the monitor and internal memory is used for recording
and playback. Note that because camera malfunction could cause internal memory to become
corrupted, the pictures in internal memory should periodically be transferred to a computer and
saved on the computer hard disk or on removable media such as CDs or DVDs. The pictures in
internal memory can also be copied to a memory card (see page 89). To prevent internal memory
from becoming full, be sure to delete pictures when they are no longer needed.
When a memory card is inserted as described below, the card will be used for recording and playback.
■ Compatible Memory Cards
SanDisk SD and SDHC memory cards have been tested and approved for use in the camera. Use
a card with a class 4 write speed (4 MB/s) or better when shooting HD movies. A complete list of
approved memory cards is available at http://www.fujifilm.com/products/digital_cameras/index.html.
Operation is not guaranteed with other cards. The camera can not be used with MultiMediaCard
(MMC) or xD-Picture Cards.
C Caution
SD memory cards can be locked, making it impossible to format the card or to record or
delete images. Before inserting an SD memory card, slide the write-protect switch to the
unlocked position.
Write-protect switch
8
Inserting a Memory Card
■ Inserting a Memory Card
Turn the camera off, and open the
battery-chamber cover.
1
Click
3 Close the battery-chamber cover.
First Steps
2
Insert the memory card firmly until you
hear (feel) a click.
Holding the memory card in the orientation
shown below, slide it all the way in. Press
firmly until it clicks into place.
C Caution
Be sure card is in correct orientation; do not
insert at an angle or use force. If the memory
card is not inserted correctly, d will appear
in the monitor and images will be recorded to
internal memory.
Battery
9
Inserting a Memory Card
Removing Memory Cards
After confirming that the camera
is off, press the card in and then
release it slowly. The card can
now be removed by hand.
C Cautions
• The memory card may spring out if you remove
your finger immediately after pushing the card in.
• Memory cards may be warm to the touch after
being removed from the camera. This is normal
and does not indicate a malfunction.
C Cautions
• Do not turn the camera off or remove the memory card
while the memory card is being formatted or data are being
recorded to or deleted from the card. Failure to observe
this precaution could damage the card.
• Format SD memory cards before first use, and be
sure to reformat all memory cards after using them
in a computer or other device. For more information
on formatting memory cards, see page 97.
• Memory cards are small and can be swallowed;
keep out of reach of children. If a child swallows a
memory card, seek medical assistance immediately.
10
• miniSD or microSD adapters that are larger or smaller
than the standard dimensions of an SD card may not
eject normally; if the card does not eject, take the
camera to an authorized service representative. Do
not forcibly remove the card.
• Do not affix labels to memory cards. Peeling labels
can cause camera malfunction.
• Movie recording may be interrupted with some
types of SD memory card.
• The data in internal memory may be erased or
corrupted when the camera is repaired. Please note
that the repairer will be able to view pictures in
internal memory.
• Formatting a memory card or internal memory
in the camera creates a folder in which pictures
are stored. Do not rename or delete this folder or
use a computer or other device to edit, delete, or
rename image files. Always use the camera to delete
pictures from memory cards and internal memory;
before editing or renaming files, copy them to a
computer and edit or rename the copies, not the
originals.
Turning the Camera on and off
Shooting Mode
Playback
y
Mode
Press the n button to turn the camera on.
The lens will extend and the lens cover will open.
To turn the camera on and begin playback, press
the D button for about a second.
B Tip: Switching to Playback Mode
Press the D button for about a second to start
playback. Press the shutter button halfway to return
to shooting mode.
Press the n button to turn the camera off.
First Steps
Press n again to turn the camera off.
B Tip: Switching to Shooting Mode
To exit to shooting mode, press the shutter button
halfway. Press the D button to return to playback.
C Cautions
• Forcibly preventing the lens from extending could
cause damage or product malfunction.
• Pictures can be affected by fingerprints and other
marks on the lens. Keep the lens clean.
• The n button does not completely disconnect
the camera from its power supply.
B Tip: Auto Power Off
The camera will turn off automatically if no operations are performed for the length of time selected in the
o AUTO POWER OFF menu (pg. 99). To turn the camera on, use the n button or press the D button
for about a second.
11
Basic Setup
A language-selection dialog is displayed the first time the camera is turned on. Set up the camera as
described below (for information on resetting the clock or changing languages, see page 96).
1 Choose a language.
2 Set the date and time.
DATE / T ME NOT SET
START MENU
2012
2011
ENGLISH
FRANCAIS
DEUTSCH
ESPAÑOL
PORTUGUÊS
SET
YY. MM. DD
NO
1.1 Press the selector up or down
to highlight a language.
1.2 Press MENU/OK.
SET
1. 1
12 : 00
AM
NO
2.1 Press the selector left or right
to highlight the year, month,
day, hour, or minute and press
up or down to change. To change the
order in which the year, month, and day
are displayed, highlight the date format
and press the selector up or down.
2.2 Press MENU/OK.
12
2010
2009
2008
Basic Setup
3 Choose power management options.
POWER MANAGEMENT
POWER SAVE
QUICK AF
CLEAR DISPLAY
SET
NO
3.1 Press the selector up or
down to highlight one of the
following options:
• v POWER SAVE: Save battery power.
• w QUICK AF: Reduce focusing time,
ensuring a quick shutter response.
• x CLEAR DISPLAY: Choose this option for
a brighter, higher quality display.
First Steps
Power saving for longer
battery life
B Tip: The Camera Clock
If the battery is removed for an extended period, the
camera clock will be reset and the language-selection
dialog will be displayed when the camera is turned
on. Set up the camera again. If the battery is left in
the camera or an optional AC adapter connected
for about four days, the battery can be removed for
about seven days without resetting clock, language
selection, or power management options.
3.2 Press MENU/OK.
13
Taking Pictures in r (P AUTO) Mode
This section describes how to take pictures in r (P AUTO) mode.
the camera on.
1 Turn
Press the n button to turn the
the battery level.
3 Check
Check the battery level in the display.
camera on.
q
Basic Photography and Playback
14
O mode.
2 Select
Rotate the mode dial to O.
B Tip: r (P AUTO)
The camera automatically selects the scene and
P mode according to shooting conditions.
Indicator
Q
(white)
P
(white)
O
(red)
N
(blinks red)
w
e
r
Description
Battery partially discharged.
Battery more than half discharged.
Low battery. Charge as soon as
possible.
Battery exhausted. Turn camera off
and charge battery.
Taking Pictures in r (P AUTO) Mode
a picture using the zoom control.
4 Frame
In this mode, the camera automatically
Display when
portrait subject is
detected.
Mode
Type of subject or scene detected
H PORTRAIT: Human portrait subject.
LANDSCAPE: Man-made or natural
I
landscape.
J NIGHT: Poorly lit landscape.
K MACRO: Subject close to camera.
T BACKLIT PORTRAIT: Back-lit portrait subject.
Z NIGHT PORTRAIT: Poorly lit portrait subject.
A Notes
• L (AUTO) will be selected if the subject does not
match the scenes listed above.
• I appears on the display while in r. The
camera continuously analyzes the scene, always
trying to detect faces.
• The camera focuses continuously, increasing the
drain on the battery. The sound of the camera
focusing may be audible.
Basic Photography and Playback
analyzes the composition and selects the
appropriate scene mode according to
the subject and shooting conditions. The
selected mode is displayed as shown below.
When the shutter button is pressed halfway,
the camera selects the optimal P
mode, which is displayed next to the scene
mode icon.
o IMAGE SIZE
If S is selected for o IMAGE SIZE in r mode,
the camera will automatically select the optimal
image size (pg. 67).
15
Taking Pictures in r (P AUTO) Mode
How to use the zoom control
Select B to zoom out
1.6x
Select A to zoom in
7.6x
Holding the Camera
Hold the camera steady
with both hands and brace
your elbows against your
sides. Shaking or unsteady
hands can blur your shots.
Zoom indicator
The zoom speed can be
changed by adjusting
the position of the zoom
control.
16
To prevent pictures that
are out of focus or too dark
(underexposed), keep your
fingers and other objects
away from the lens and
flash.
Taking Pictures in r (P AUTO) Mode
Framing Guideline and Post-Shot Assist Window
In shooting mode, press DISP/BACK to select a
shooting display format. The selection changes
each time DISP/BACK is pressed.
INFORMATION ON
INFORMATION OFF
SET UP
3 /4
LCD B
AUTO
CONTINUOUS
SHOOTING ONLY
DUAL
RED E OFF
DIGIT
AF LL
B Tip
When using the camera with a tripod, Z DUAL IS
MODE is recommended to be OFF.
HD FRAMING
BEST FRAMING
• BEST FRAMING: To use the best framing, position the
main subject at the intersection of two lines or
align one of the horizontal lines with the horizon.
• HD FRAMING: Displays the High Definition (HD) 16 : 9
crop.
A Note
Sensitivity is raised when dual IS is in effect. Note
that blurring may still occur depending on the scene
or shooting conditions.
Basic Photography and Playback
Avoiding Blurred Pictures
If the subject is poorly lit,
blurring caused by camera
shake can be reduced by
activating the Z DUAL IS
MODE. k CONTINUOUS,
l SHOOTING ONLY or OFF
can be set in the setup menu
(pg. 93).
17
Taking Pictures in r (P AUTO) Mode
Focus.
5 Press
the shutter button halfway
to focus.
A Note
The lens may make a noise when the camera
focuses. This is normal.
If the camera is able to focus, it will beep twice
and the indicator lamp will glow green.
If the camera is unable to focus, the red colored
focus frame and R will appear in the
monitor, and the indicator lamp will blink
green. Change the composition or use
focus lock (pg. 32).
Shoot.
6 Smoothly
press the shutter
button the rest of the way down
to take the picture.
B Tip: The Shutter Button
The shutter button has two positions. Pressing the
shutter button halfway (q) sets focus and exposure;
to shoot, press the shutter button the rest of the way
down (w).
Double
beep
q
Press halfway
Click
w
Press the rest of
the way down
A Note
If the subject is poorly lit, the flash may fire when the
picture is taken. For information on using the flash
when lighting is poor, see page 37.
18
Taking Pictures in r (P AUTO) Mode
U Silent Mode
In situations in which camera sounds or lights may
be unwelcome, hold the DISP/BACK button down
until U is displayed (note that silent mode is not
available during movie or voice memo playback).
Indicator lamp
The indicator lamp shows camera status as follows:
Indicator lamp
Camera status
Glows green Focus locked.
Blur, focus, or exposure warning.
Blinks green
Picture can be taken.
Blinks green Recording pictures. Additional
and orange pictures can be taken.
Glows
Recording pictures. No additional
orange
pictures can be taken at this time.
Flash charging; flash will not fire
Blinks orange
when picture is taken.
Lens or memory error (internal
memory or memory card full or not
Blinks red
formatted, format error, or other
memory error).
Basic Photography and Playback
The camera speaker, flash, and AF-assist illuminator/
self-timer lamp turn off and flash and volume
settings can not be adjusted (note that the flash will
still fire in A mode). To restore normal operation,
press the DISP/BACK button until the U icon is no
longer displayed. Silent mode can also be set from
the setup menu (pg. 93).
The Indicator Lamp
B Tip: Warnings
Detailed warnings appear in the display. See pages
114–117 for more information.
19
Viewing Pictures
Pictures can be viewed in the monitor. When taking important photographs, take a test shot and
check the results.
1 Press the D button.
Deleting Pictures
To delete the picture currently displayed
in the monitor, press the selector up (I).
The following dialog will be displayed.
ERASE OK?
The most recent picture will be displayed in
the monitor.
OK
CANCEL
SET
100 0001
100-0001
400
4:3 N
12 / 31 / 2050 10 : 00 AM
1/250 F3.3
additional pictures.
2 View
Press the selector right to view
pictures in the order recorded, left
to view pictures in reverse order.
Press the shutter button to exit to shooting
mode.
20
To delete the picture, highlight OK and
press MENU/OK. To exit without deleting
the picture, highlight CANCEL and press
MENU/OK.
B Tip: The Playback Menu
Pictures can also be deleted from the playback
menu (pg. 46).
Shooting Mode
Choose a shooting mode according to the scene or type of subject. To choose a shooting mode,
rotate the mode dial to the desired setting (pg. 4). The following modes are available:
k AUTO
2 Highlight A P MODE.
Choose for crisp, clear snapshots. This mode is
recommended in most situations.
the selector right to display
3 Press
the following menu.
O EXR
MENU/OK to display the
1 Press
shooting menu.
SHOOTING MENU
1/2
MODE
ISO
IMAGE SIZE
IMAGE QUAL TY
DYNAMIC RANGE
FILM SIMULATION
AUTO
4:3
N
AUTO
AUTO
RESOLUTION PRIOR TY
HIGH ISO & LOW NOISE
D RANGE PR ORITY
Selects EXR mode
and camera settings
for each scene.
SET
CANCEL
More on Photography
To let the camera automatically
optimize settings for your current
subject, or to improve clarity, reduce
noise, or enhance dynamic range, rotate the
mode dial to O and follow the steps below:
EXIT
21
Shooting Mode
the selector up or down to
4 Press
highlight one of the following
options.
Option
Description
The camera automatically
selects the scene and P
rP AUTO
mode according to shooting
conditions (pg. 14).
s RESOLUTION
Choose for crisp, clear shots.
PRIORITY
t HIGH ISO & Reduce noise in pictures taken
LOW NOISE at high sensitivities.
Increase the amount of
detail visible in highlights.
u D-RANGE
U DYNAMIC RANGE is set to
PRIORITY
D (800%).
MENU/OK to select the
5 Press
highlighted option.
DISP/BACK to exit from the
6 Press
menu.
22
A NATURAL
L&K
This mode helps ensure good results with backlit
subjects and in other situations with difficult
lighting. Each time the shutter button is pressed,
the camera takes two shots: one shot without
the flash to preserve natural lighting, followed
immediately by a second shot with the flash. Do
not move the camera until shooting is complete.
A Notes
• Do not use where flash photography is prohibited.
The flash will fire even in silent mode.
• Only available if memory remains for two pictures.
Shooting Mode
B NATURAL
LL
LIGHT
G
3 Highlight A SCENE POSITION.
Capture natural light indoors,
under low light, or where the
flash can not be used. The
flash turns off and sensitivity is
raised to reduce blur.
the selector right to display
4 Press
shooting mode options.
the selector up or down to
5 Press
highlight a scene (pg. 26).
SP SCENE POSITION
1 Rotate the mode dial to SP.
PORTRAIT
Portrait with soft
overall tone and
beautiful skin tones
SET
CANCEL
MENU/OK to select the
6 Press
highlighted option.
MENU/OK to display the
2 Press
following menu.
SHOOTING MENU
1/2
SCENE POSITION
ISO
IMAGE SIZE
IMAGE QUAL TY
DYNAMIC RANGE
FILM SIMULATION
AUTO
4:3
N
AUTO
More on Photography
The camera offers a choice of “scenes,” each
adapted to particular shooting conditions or a
specific type of subject, which can be assigned
to the SP position on the mode dial:
DISP/BACK to exit from the
7 Press
menu.
Until the setting is changed as described above,
the chosen scene will be selected whenever the
mode dial is rotated to SP.
EXIT
23
Shooting Mode
G PRO FOCUS MODE
Choose for soft focusing the background of a
subject such as a portrait or a flower to make it
impressive. When the shutter button is pressed,
the camera automatically takes up to 3 pictures
and creates one image with a sharp focused
subject that has a soft focused background. The
camera provides you with a soft focus effect like
an SLR camera. Press the selector left or right to
select SOFTNESS in 3 steps before shooting.
A Notes
• When a subject is too close to the background, the
camera may not create effect to a picture. When
the message 5 CANNOT CREATE EFFECT appears
during focus lock, take a little distance from your
subject and use the zoom control to adjust.
• When shooting a moving subject, the function may
not work.
• When the camera fails to create effect, the message
5 PLAYBACK TO CHECK IMAGE appears. Take a
picture again.
C Cautions
• Hold the camera firmly while you shoot.
• Frame coverage is reduced in this mode.
24
B Tip: H SAVE ORIGINAL IMAGE
Select ON for the H SAVE ORIGINAL IMAGE option
in the setup menu (pg. 93) to save unprocessed
copies of pictures.
F PRO LOW-LIGHT MODE
Choose for shooting a subject under low light
or a still subject by using the telephoto zoom.
When the shutter button is pressed, the camera
automatically takes up to 4 pictures and merges
the pictures together. Blurring caused by camera
shake can be reduced and pictures with low
noise can be taken even with high sensitivity.
A Notes
• When shooting a moving subject, the function may
not work.
• Pictures may be saved without merged, depending
on the shooting condition, or when moving the
camera a lot during shooting.
C Cautions
• Hold the camera firmly while you shoot.
• Frame coverage is reduced in this mode.
Shooting Mode
B Tip: H SAVE ORIGINAL IMAGE
Select ON for the H SAVE ORIGINAL IMAGE option
in the setup menu (pg. 93) to save unprocessed
copies of pictures.
Y DOG/T CAT
When Y DOG or T CAT is selected, the
camera detects and focuses the front face of a
dog or cat.
More on Photography
When Y DOG or T CAT is selected for
SCENE POSITION, 5 AUTO RELEASE is
available in Self-Timer options. When the camera
detects and focuses the face of a dog or cat in
5 AUTO RELEASE, the camera automatically
releases the shutter.
The detected faces can be used with following
functions.
• SLIDE SHOW (pg. 82)
• IMAGE DISP. > ZOOM(CONTINUOUS) (pg. 97)
• PRINT ORDER(DPOF) (pg. 56)
• CROP (pg. 86)
C Cautions
• Although the camera detects faces of many kinds
of dogs or cats in Y DOG or T CAT, some kinds
of dogs or cats may not be detected. Also, some
shooting conditions may prevent the camera from
detecting the face of a dog or cat.
• If no face is detected when the shutter button
is pressed halfway, the camera will focus on the
subject at the center of the display.
• When a face is not detected, place the subject in the
center of a frame.
• If the face of a dog or cat is not detected, face zoom
will not be available even when the B button is
pressed during playback.
• Y DOG and T CAT may not be effective under
following conditions:
- kinds of dogs or cats whose whole faces are black.
- kinds of dogs or cats whose whole faces are
covered with long hair.
25
Shooting Mode
Scene
Description
Choose for soft focusing the background of a subject such as a portrait or a flower to make it
G PRO FOCUS
impressive.
Choose for shooting a subject under low light or a still subject by using the telephoto zoom.
F PRO LOW-LIGHT
Choose for soft-toned portraits with natural skin tones.
U PORTRAIT
V PORTRAIT ENHANCER Choose for a smooth skin effect in soft-focus portraits.
Choose for shooting a dog. The mode optimizes to focus on faces of dogs.
Y DOG
Choose for shooting a cat. The mode optimizes to focus on faces of cats.
T CAT
Choose for crisp, clear daylight shots of buildings and landscapes.
K LANDSCAPE
Choose when photographing moving subjects. w QUICK AF is automatically selected for
L SPORT
m POWER MANAGEMENT and priority is given to faster shutter speeds.
Choose this mode for poorly lit twilight or night scenes. Sensitivity is automatically raised to reduce
D NIGHT
blur caused by camera shake.
Choose this mode for slow shutter speeds when shooting at night. Use a tripod to prevent blur.
U NIGHT (TRIPOD)
Slow shutter speeds are used to capture the expanding burst of light from a firework. Use a tripod
W FIREWORKS
to prevent blur.
Record the vivid colors in sunrises and sunsets.
E SUNSET
Choose for crisp, clear shots that capture the brightness of scenes dominated by shining white snow.
F SNOW
Choose for crisp, clear shots that capture the brightness of sunlit beaches.
G BEACH
Choose for vivid blues when using an optional waterproof case to take photographs underwater.
X UNDERWATER
Capture indoor background lighting under low-light conditions.
I PARTY
Choose for vivid close-ups of flowers. The camera focuses in the macro range.
O FLOWER
Take clear pictures of text or drawings in print. The camera focuses in the macro range.
P TEXT
26
Shooting Mode
M MANUAL
In this mode, you choose both shutter speed and aperture. If desired, exposure can be altered from
the value suggested by the camera.
1 Rotate the mode dial to M.
the l button. Shutter speed
2 Press
and aperture will be displayed.
the selector left or right to
4 Press
choose the shutter speed.
C Caution
Noise in the form of randomly-spaced bright pixels
may occur in long exposures.
Shutter speed
SET
200
6 Take pictures.
F3. 3
Aperture
the selector up or down to
3 Press
choose the aperture.
The Exposure Indicator
The amount the picture will
be under- or over-exposed at
current settings is shown by the
exposure indicator.
More on Photography
MENU/OK to return to shooting
5 Press
mode.
SET
200
F3. 3
27
Shooting Mode
P PROGRAM AE/A APERTURE PRIORITY AE
Mode P offers a choice of program AE (autoexposure), in which the camera sets exposure
automatically, and aperture priority AE, in which you adjust aperture to soften background details or
bring both background and foreground into focus while letting the camera control shutter speed for
optimal exposure. To take pictures in program and aperture priority AE:
1 Rotate the mode dial to P.
MENU/OK to display the
2 Press
shooting menu.
the selector up or down to
3 Press
highlight A SHOOTING MODE.
the selector right to display
4 Press
shooting mode options.
28
the selector up or down to
5 Press
highlight an option.
SHOOTING MENU
1/2
SHOO
1600
4
N
AUTO
PROGRAM AE
APERTURE PR ORITY AE
MENU/OK to select the
6 Press
highlighted option.
DISP/BACK to exit from the
7 Press
menu.
Shooting Mode
MENU/OK to return to shooting
10 Press
mode.
the selector up (l) to display
8 Press
exposure compensation (program
AE) or aperture (aperture priority
AE).
P
11 Take pictures.
A
SET
SET
0
F3. 3
0
Aperture
(aperture priority AE)
the selector button to choose exposure
9 Press
compensation (program AE) or aperture
(aperture priority AE). If the correct exposure
can not be achieved at the aperture selected
for aperture priority AE, the shutter speed will
be displayed in red.
More on Photography
Exposure compensation
(program AE)
C Caution
If the subject is outside the metering range of the
camera, the shutter speed and aperture displays
will show “---”. Press the shutter button halfway to
measure exposure again.
29
B Intelligent Face Detection
Intelligent Face Detection allows the camera to automatically detect human faces and set focus and
exposure for a face anywhere in the frame for shots that emphasize portrait subjects. Choose for
group portraits (in vertical or horizontal orientations) to prevent the camera from focusing on the
background. Intelligent Face Detection also offers a red-eye removal option for removing “red-eye”
effects caused by the flash.
Intelligent Face Detection on.
1 Turn
Press the B button to turn Intelligent Face
Detection on. The selection changes each
time the B button is pressed.
A Note
When removing red-eye effect, select ON for
a RED EYE REMOVAL in the setup menu (pg.
93).
30
the picture.
2 Frame
If a face is detected, it will
be indicated by a green
border. If there is more
than one face in the
frame, the camera will
Green border
select the face closest
to the center; other faces are indicated by
white borders.
Focus.
3 Press
the shutter button halfway
to focus on the subject in the
green border. Note that, in some
shooting modes, exposure is
adjusted for the current shooting mode
and may not be optimized for the selected
subject.
B Intelligent Face Detection
C Caution
If no face is detected when the shutter button is
pressed halfway (pg. 108), the camera will focus
on the subject at the center of the display and
red-eye will not be removed.
Shoot.
4 Press
the shutter button all the
way down to shoot.
B Tip: Red-Eye Removal
Select ON for the H SAVE ORIGINAL IMAGE
option in the setup menu (pg. 93) to save
unprocessed copies of pictures created with
a RED EYE REMOVAL.
7
The following functions can be used with Intelligent
Face Detection.
RED EYE REMOVAL (pg. 95)/IMAGE SEARCH
(pg. 44)/SLIDE SHOW (pg. 82)/IMAGE DISP. >
ZOOM(CONTINUOUS) (pg. 100)/PRINT ORDER
(DPOF) (pg. 56)/CROP (pg. 86)
More on Photography
C Caution
If the subject moves as the shutter button
is pressed, their face may not be in the area
indicated by the green border when the picture
is taken.
Intelligent Face Detection
Intelligent Face Detection is
recommended when using the
self-timer for group- or selfportraits (pg. 39).
If a face has been registered,
the camera prioritizes focus
and exposure to that face when
there are several faces detected.
31
Focus Lock
To compose photographs with off-center subjects:
1 Position the subject in the focus frame.
the picture.
3 Recompose
Keeping the shutter button pressed
halfway, recompose the picture.
Focus.
2 Press
the shutter button halfway to set
focus and exposure. Focus and exposure
will remain locked while the shutter button
is pressed halfway (AF/AE lock).
Press
halfway
250
F3.3
Repeat steps 1 and 2 as desired to refocus
before taking the picture.
32
250
F3 3
F3.3
Shoot.
4 Press
the shutter-release button the rest of
the way down to take the picture.
Press the rest of
the way down
Focus Lock
Autofocus
Although the camera boasts a high-precision autofocus system, it may be unable to focus on the subjects
listed below. If the camera is unable to focus using autofocus, use focus lock (pg. 32) to focus on another
subject at the same distance and then recompose the photograph.
• Very shiny subjects such as mirrors or car bodies.
•
•
•
•
Subjects photographed through a window or other reflective object.
Dark subjects and subjects that absorb rather than reflect light, such as hair or fur.
Insubstantial subjects, such as smoke or flame.
Subjects that show little contrast with the background (for example, subjects in clothing that is the same
color as the background).
• Subjects positioned in front of or behind a high-contrast object that is also in the focus frame (for example, a
subject photographed against a backdrop of highly contrasting elements).
More on Photography
• Fast-moving subjects.
33
Focus Lock
The AF-Assist Illuminator
If the subject is poorly lit, the AF-assist illuminator will light to assist the focus operation when the shutter
button is pressed halfway.
AF-assist
illuminator
A Notes
• Avoid shining the AF-assist illuminator directly into your subject’s eyes. See page 93 for information on
disabling the AF-assist illuminator.
• The camera may be unable to focus using the AF-assist illuminator in some cases. If the camera is unable to
focus in macro mode (pg. 36), try increasing the distance to the subject.
• The AF-assist illuminator is not available in silent mode.
34
5 Exposure Compensation
Use exposure compensation when photographing very bright, very dark, or high-contrast subjects.
the selector up (l).
1 Press
The exposure indicator will be displayed.
to shooting mode.
3 Return
Press MENU/OK to return to
shooting mode.
A
4 Take pictures.
SET
F3. 3
0
visible in the display.
Choose positive (+) values
to increase exposure
More on Photography
a value.
2 Choose
Press the selector button. The effect is
A Note
A 5 icon and exposure indicator are displayed at
settings other than ±0. Exposure compensation is not
reset when the camera is turned off; to restore normal
exposure control, choose a value of ±0.
Choose negative (–) values
to reduce exposure
35
L Macro Mode (Close-ups)
For close-ups, press the selector left (L). The selection changes each time the selector is pressed.
OFF
MACRO
When macro mode is in effect, the camera focuses on subjects near the center of the frame. Use the
zoom control to compose pictures.
To exit macro mode, press the selector left (L) and select OFF. Macro mode can also be cancelled by
turning the camera off or selecting another shooting mode.
A Notes
• Use of a tripod is recommended to prevent blur caused by camera shake.
• The flash may fail to light the entire subject at very short ranges. Increase the distance to the subject and try
again.
36
K Using the Flash (Super Intelligent Flash)
When the flash is used, the camera’s Super Intelligent Flash system instantly analyzes the scene based
on such factors as the brightness of the subject, its position in the frame, and its distance from the
camera. Flash output and sensitivity are adjusted to ensure that the main subject is correctly exposed
while preserving the effects of ambient background lighting, even in dimly-lit indoor scenes. Use the
flash when lighting is poor, for example when shooting at night or indoors under low light.
a flash mode.
1 Choose
Press the selector right (K). The flash mode changes each time the
Mode
Description
4 (AUTO FLASH) The flash fires when required. Recommended in most situations.
The flash fires whenever a picture is taken. Use for backlit subjects or for natural
K (FORCED FLASH)
coloration when shooting in bright light.
The flash does not fire even when the subject is poorly lit. 0 will appear in the
W (SUPPRESSED
monitor at slow shutter speeds to warn that pictures may be blurred. Use of a
FLASH)
tripod is recommended.
Capture both the main subject and the background under low light (note that
T (SLOW SYNCHRO)
brightly lit scenes may be overexposed).
More on Photography
selector is pressed; in modes other than 4, the current mode
is indicated by an icon in the display. Choose from the following
options:
37
K Using the Flash (Super Intelligent Flash)
Focus.
2 Press
the shutter button halfway to focus. If the flash will fire, X will be displayed
when the shutter button is pressed halfway. At slow shutter speeds, 0 will appear in
the display to warn that pictures may be blurred; use of a tripod is recommended.
Shoot.
3 Press
the shutter button the rest of the way down to shoot.
C Caution
The flash may fire several times with each shot. Do not move the camera until shooting is
complete.
Red-Eye Removal
When Intelligent Face Detection is active (pg. 30), and ON is selected for a RED EYE REMOVAL
in the setup menu (pg. 93), red-eye removal is available in V, U, and Z. Red-eye removal
minimizes “red-eye” caused when light from the flash is reflected from the subject’s retinas as
shown in the illustration at right.
38
J Using the Self-Timer
The camera offers a ten-second timer that allows photographers to appear in their own photographs,
and a two-second timer that can be used to avoid blur caused by the camera moving when the
shutter button is pressed. The self-timer is available in all shooting modes.
the timer.
1 Set
Press the selector down (J). The selection changes each time the selector is pressed. The
current self-timer mode is displayed in the monitor.
Choose from y (self-timer off),
c (10 s delay), or b (2 s delay)
OFF
OFF
More on Photography
Focus.
2 Press
the shutter button halfway to focus.
C Caution
Stand behind the camera when using the shutter button. Standing in front of the lens can
interfere with focus and exposure.
the timer.
3 Start
Press the shutter button the rest of the way down to start the timer.
The display in the monitor shows the number of seconds remaining
until the shutter is released. To stop the timer before the picture is
taken, press DISP/BACK.
9
39
J Using the Self-Timer
The self-timer lamp on the front of the camera will blink
immediately before the picture is taken. If the twosecond timer is selected, the self-timer lamp will blink
as the timer counts down.
Intelligent Face Detection
Because it ensures that the faces of portrait subjects will be in focus, Intelligent Face Detection (pg. 30) is
recommended when using the self-timer for group portraits or self-portraits. To use the self-timer with
Intelligent Face Detection, turn Intelligent Face Detection on, set the timer as described in Step 1, and then
press the shutter button all the way down to start the timer. The camera will detect faces while the timer is
counting down and adjust focus and exposure immediately before the shutter is released. Be careful not to
move until the picture has been recorded.
A Note
The self-timer turns off automatically when the picture is taken, a different shooting mode is selected, playback
mode is selected, or the camera is turned off.
40
Playback Options
To view the most recent picture in the monitor,
press the D button.
100 0001
100-0001
Choosing a Display Format
In playback mode, press DISP/BACK to select a
playback display format.
400
4:3 N
12 / 31 / 2050 10 : 00 AM
1 250 F3.3
1/250
F3 3
The selection changes each time DISP/BACK is
pressed.
INFORMATION ON
INFORMATION OFF
100 0001
100-0001
400
4:3 N
12 / 31 / 2050 10 : 00 AM
1/250 F3.3
F3 3
More on Playback
Press the selector right to view pictures
in the order recorded, left to view
pictures in reverse order. Keep the
selector pressed to scroll rapidly to the desired
frame.
A Note
Pictures taken using other cameras are indicated by a e (“gift image”) icon during playback.
41
Playback Options
Playback
y
Zoom
Select A to zoom in on pictures displayed in
single-frame playback; select B to zoom out.
When the picture is zoomed in, the selector can
be used to view areas of the image not currently
visible in the display.
Zoom indicator
Navigation window shows
portion of image currently
displayed in monitor
Press DISP/BACK to exit zoom.
A Note
Playback zoom is not available with cropped or
resized copies saved at a size of t.
42
Intelligent Face Detection
Pictures taken with Intelligent
Face Detection (pg. 30) are
indicated by a B icon. Press
the B button to zoom in
ZOOM
BACK
on the subject selected with
Intelligent Face Detection. You
can then use the zoom control to zoom in and out.
Playback Options
Multi-Frame Playback
y
To change the number of images displayed,
select B when a picture is shown full-frame in
the monitor.
12 / 31 / 2050
B Tip: Two-Frame Display
Two-frame display can be used
to compare pictures taken in A
mode.
10 : 00 AM
Select A to
reduce the
number of images
displayed.
More on Playback
Select B to
increase the
number of
pictures displayed
to one frame with
previous and next,
two, nine, and a
hundred.
Use the selector to highlight images and press
MENU/OK to view the highlighted image full frame.
In the nine- and hundred-frame displays, press
the selector up or down to view more pictures.
43
V Image Search
Image Search based on categories
Search for pictures by date, subject, scene, and
file type.
MENU/OK to display the
1 Press
playback menu.
the selector up or down to
2 Press
highlight V IMAGE SEARCH.
MENU/OK to display the search
3 Press
category.
the selector up or down
4 Press
to highlight the desired search
category.
Option
BY DATE
BY FACE
BY SCENE
BY TYPE
OF DATA
44
Description
Show images based on the
specified date.
Show images based on specified
face information.
Show images based on the
specified scene mode.
Show images based on whether
still pictures or movies.
MENU/OK to select the
5 Press
highlighted search category.
A detailed search list will be
displayed.
a category in the list.
6 Select
Specified images will be displayed.
V Image Search
Using
g Playback
y
Menu with Image
g Search
Three playback menus can be performed with
image search mode.
MENU/OK while the search
1 Press
results are displayed.
The playback menu will be
displayed.
the selector up or down to
2 Press
highlight the desired menu item.
B Tips
• For each operation, refer to the page listed.
Option
See Page
46
MERASE
85
OPROTECT
82
qSLIDE SHOW
More on Playback
MENU/OK to select the
3 Press
highlighted menu.
• Select EXIT SEARCH to go back to the normal
playback mode.
45
M Deleting Pictures
The ERASE option in the playback menu can be used to delete still pictures and movies, increasing
the amount of space available on the memory card or in internal memory (for information on
deleting pictures in single-frame playback, see page 20). Note that deleted pictures can not be
recovered. Copy important pictures to a computer or other storage device before proceeding.
MENU/OK to display the
1 Press
playback menu.
PLAYBACK MENU
the selector up or down to
4 Press
highlight FRAME or ALL FRAMES.
1 /3
MENU/OK to display options for
5 Press
the selected item (see following
IMAGE SEARCH
ERASE
SLIDE SHOW
RED EYE REMOVAL
PROTECT
CROP
page).
EXIT
2
Press the selector up or down to
highlight M ERASE.
the selector right to display
3 Press
delete options.
PLAYBACK MENU
IMAG
BACK
ERAS
SLIDE FRAME
RED E ALL FRAMES
PROT
CROP
46
1 /3
B Tips: Deleting Pictures
• When a memory card is inserted, pictures will be
deleted from the memory card; otherwise, pictures
will be deleted from internal memory.
• Protected pictures can not be deleted. Remove
protection from any pictures you wish to delete (pg.
85).
• If a message appears stating that the selected
images are part of a DPOF print order, press MENU/OK
to delete the pictures.
M Deleting Pictures
■ FRAME: Deleting Selected Images
Selecting FRAME displays the
dialog shown at right.
■ ALL FRAMES: Deleting All Images
ERASE ALL OK?
Selecting ALL FRAMES
IT MAY TAKE A WHILE
displays the confirmation
OK
shown at right.
CANCEL
ERASE OK?
YES
SET
CANCEL
Press DISP/BACK to exit when all the desired
pictures have been deleted.
Highlight OK and press MENU/
OK to delete all unprotected
pictures.
The dialog shown at right is
displayed during deletion.
Press DISP/BACK to cancel
before all pictures have been
CANCEL
deleted (any pictures deleted
before the button was pressed can not be
recovered).
More on Playback
Press the selector left or right
to scroll through pictures and
press MENU/OK to delete the
current picture (the picture
is deleted immediately; be
careful not to delete the
wrong picture).
47
A Recording Movies
Shoot short movies with sound. Sound is recorded via the built-in microphone; do not cover the
microphone during recording.
Rotate the mode dial to A (movie
1 mode).
12s
STAN BY
Display shows time
available
the scene using the zoom
2 Frame
control.
Movies
48
12s
STANDBY
Zoom indicator
the shutter button all the way
3 Press
down to start recording.
REC
EC
12s
z REC and time
remaining are
displayed
B Tip
There is no need to keep the shutter button pressed
during recording.
A Recording Movies
A Notes
• Focus, exposure and white balance are adjusted
automatically throughout recording. The color
and brightness of the image may vary from that
displayed before recording begins.
• Movies are recorded as motion JPEG files.
• If the subject is poorly lit, the AF-assist lamp
may light to assist the focus operation. To turn
the AF-assist lamp off, select OFF for the b AF
ILLUMINATOR option in the setup menu (pg. 93).
• Vertical or horizontal streaks may appear in movies
containing very bright subjects. This is normal and
does not indicate a malfunction.
4
B Tip: B Intelligent Face Detection
The camera automatically detects faces and optimizes
focus and exposure. Press the B button to turn the
function on and off.
Choosing the Frame Size
SHOOTING MENU
1
To choose the frame size,
press MENU/OK and select
QUAL
1280
5m00s
AUTO
10m59s
o QUALITY.
Choose a pixel size in the
following:
• )1280 (1280 × 720) for high definition movies.
• ! (640 × 480) for standard definition movies.
Press DISP/BACK to return to movie recording mode.
2
Movies
Press the shutter button halfway
to end recording. Recording ends
automatically when the movie
reaches maximum length or
memory is full.
C Caution
The indicator lamp lights while movies are being
recorded. Do not open the battery chamber card
during shooting or while the indicator lamp is lit.
Failure to observe this precaution could prevent the
movie from being played back.
49
A Recording Movies
Matching the light source
Select C WHITE BALANCE in the shooting menu
to display the list below.
Option
Description
AUTO White balance adjusted automatically.
p
q
s
t
u
r
g
50
For subjects in direct sunlight.
For subjects in the shade.
Use under “daylight” fluorescent lights.
Use under “warm white” fluorescent lights.
Use under “cool white” fluorescent lights.
Use under incandescent lighting.
For underwater photography.
Selecting focus mode
Select F AF MODE in the shooting menu.
• w CENTER: When zooming in or out, the camera
refocus on the subject in the center of the frame.
• T CONTINUOUS: The camera continuously
adjusts focus to reflect changes in the distance to
the main subject.
A Note
While B Intelligent Face Detection is on, the
camera always adjusts focus continuously.
D Viewing Movies
During playback, movies are
displayed in the monitor as
shown at right. The following
operations can be performed
while a movie is displayed:
Operation
Start/pause
playback
End
playback/
delete
100 006
100-006
Progress is shown in the monitor during
playback.
15s
12 / 31 / 2050
PLAY
10 : 00 AM
Progress bar
STOP
PAUSE
B Tip: Viewing Movies on a Computer
Copy movies to the computer before viewing.
C Caution
Do not cover the speaker during playback.
Movies
Description
Press the selector down to start playback.
Press again to pause.
Press the selector up to end playback. If
playback is not in progress, pressing the
selector up will delete the current movie.
Press the selector right to advance, left to
Advance/ rewind. If playback is paused, the movie
rewind will advance or rewind one frame each
time the selector is pressed.
Press MENU/OK to pause playback and
display volume controls. Press the
Adjust
selector up or down to adjust the
volume
volume; press MENU/OK again to resume
playback.
51
Viewing Pictures on TV
Connect the camera to a TV and tune the television to the video channel to show pictures to a group.
Connect the A/V cable, as shown below. Be sure that the camera is off before connecting the cable.
Insert into A/V cable
connector
Connect yellow plug
to video-in jack
Connect white plug
to audio-in jack
Connecting the Camera to High Definition (HD) TVs
An HDMI cable (available from third-party suppliers) can be used to connect the camera to High Definition
(HD) devices (playback only).
HDMI Micro
Connector (Type D)
Connections
52
Insert into
HDMI connector
A Note
The USB cable and A/V cable cannot be used while an HDMI cable is connected.
Viewing Pictures on TV
Press D for about a second to turn the camera on. The camera monitor turns off and pictures and
voice memos are played back on the TV. Note that the camera volume controls have no effect on
sounds played on the TV; use the television volume controls to adjust the volume.
A Note
Image quality drops during movie playback.
C Caution
When connecting the cable, be sure the connectors are fully inserted.
Connections
53
Printing Pictures via USB
If the printer supports PictBridge, the camera can be connected directly to the printer and
pictures can be printed without first being copied to a computer. Note that depending on
the printer, not all the functions described below may be supported.
Connecting the Camera
Printing Selected Pictures
the supplied USB cable as shown
1 Connect
and turn the printer on.
the selector left or right to
1 Press
display a picture you wish to print.
A Note
To print one copy of the current picture, proceed
directly to Step 3.
the selector up or down to
2 Press
choose the number of copies (up
the D button for about a second
2 Press
to turn the camera on. w USB will be
displayed in the monitor, followed by the
PictBridge display shown below at right.
USB
to 99). Repeat steps 1–2 to select
additional pictures.
MENU/OK to display a
3 Press
confirmation dialog.
PRINT THESE FRAMES
TOTAL: 9 SHEETS
PICTBRIDGE
TOTAL: 00000
00 SHEETS
FRAME
OK
YES
CANCEL
SET
4 Press MENU/OK to start printing.
54
Printing Pictures via USB
B Tip: Printing the Date of Recording
To print the date of recording on pictures, press
DISP/BACK in steps 1–2 to display the PictBridge menu
(see “Printing the DPOF Print Order,” on pg. 56).
Press the selector up or down to highlight PRINT
WITH DATE y and press MENU/OK to return to the
PictBridge display (to print pictures without the date
of recording, select PRINT WITHOUT DATE). To
ensure that the date is correct, set the camera clock
before taking pictures. Note that the PRINT WITH
DATE y option is only available with printers that
support date printing.
PRINTING
CANCEL
If printing is interrupted, press D to turn the camera
off and then on again.
Disconnecting the Camera
Confirm that the above message is not displayed
and turn the camera off. Disconnect the USB cable.
Connections
A Notes
• Use an optional AC adapter and DC coupler to
power the camera for extended periods.
• Print pictures from internal memory or a memory
card that has been formatted in the camera.
• When pictures are printed via direct USB connection,
page size, print quality, and border selections are
made using the printer.
During Printing
The message shown at right is
displayed during printing. Press
DISP/BACK to cancel before all
pictures are printed (depending
on the printer, printing may end
before the current picture has
printed).
55
Printing Pictures via USB
Printing the DPOF Print Order
To print the print order created with r PRINT
ORDER (DPOF) in the playback menu (pg. 54):
In the PictBridge display, press DISP/
1 BACK
to open the PictBridge menu.
MENU/OK to display a
3 Press
confirmation dialog.
PRINT DPOF OK?
TOTAL: 9 SHEETS
PICTBRIDGE
PRINT WITH DATE
PRINT WITHOUT DATE
PRINT DPOF
YES
CANCEL
4 Press MENU/OK to start printing.
the selector up or down to
2 Press
highlight x PRINT DPOF.
56
Printing Pictures via USB
Creating a DPOF Print Order
The r PRINT ORDER (DPOF) option in the
playback menu can be used to create a digital
“print order” for PictBridge-compatible printers
(pg. 54) or devices that support DPOF.
DPOF
DPOF (Digital Print Order Format) is
standard that allows pictures to be printed
from “print orders” stored in internal
memory or on a memory card. The information in
the order includes the pictures to be printed and the
number of copies of each picture.
PLAYBACK MENU
RESI
IMAG WITH DATE
COPY WITHOUT DATE
VOIC RESET ALL
ERAS
PR N
23
WITH DATE y: Print date of
recording on pictures.
WITHOUT DATE: Print pictures without
date.
the selector left or right to
1 Press
display a picture you wish to
include in or remove from the print
order.
the selector up or down to
2 Press
choose the number of copies (up
to 99). To remove a picture from
the order, press the selector down until the
number of copies is 0.
PRINT ORDER (DPOF)
DPOF: 00001
Total number of prints
Number of copies
01 SHEETS
FRAME
SET
B Tip: Intelligent Face Detection
If the current picture was created with Intelligent
Face Detection, pressing B sets the number of
copies to the number of faces detected.
Connections
■ WITH DATE y / WITHOUT DATE
To modify the DPOF print order, select r PRINT
ORDER (DPOF) in the playback menu and press
the selector up or down to highlight WITH
DATE y or WITHOUT DATE.
Press MENU/OK and follow the steps below.
57
Printing Pictures via USB
steps 1–2 to complete the
3 Repeat
print order. Press MENU/OK to save
the print order when settings
are complete, or DISP/BACK to exit without
changing the print order.
total number of prints is
4 The
displayed in the monitor. Press
MENU/OK to exit.
The pictures in the current
print order are indicated by a
x icon during playback.
A Notes
• Remove the memory card to create or modify a print
order for the pictures in internal memory.
• Print orders can contain a maximum of 999 pictures.
RESET DPOF OK?
• If a memory card is inserted
containing a print order
created by another camera, the
message shown at right will be
YES
CANCEL
displayed. Pressing MENU/OK
cancels the print order; a new
print order must be created as described above.
• Whether WITH DATE y/WITHOUT DATE is
available may depend on the printer setting. Check
the printer.
■ RESET ALL
RESET DPOF OK?
To cancel the current print
order, select RESET ALL in the
r PRINT ORDER (DPOF)
menu. The confirmation
YES
CANCEL
shown at right will be
displayed; press MENU/OK to remove all pictures
from the order.
58
Viewing Pictures on a Computer
The supplied software can be used to copy pictures to a computer, where they can be stored,
viewed, organized, and printed. Before proceeding, install the software as described below. Do NOT
connect the camera to the computer until installation is complete.
Installing the Software
Two applications are supplied: MyFinePix Studio for Windows and FinePixViewer for the Macintosh.
Installation instructions for Windows are on pages 59–60, those for the Macintosh on pages 61–62.
Windows: Installing MyFinePix Studio
Confirm that the computer meets the following system requirements:
1
CPU
RAM
Free disk space
Video
Other
•
•
•
•
Windows 7*
Windows Vista*
Windows XP*
3 GHz Pentium 4 or better
2 GHz Pentium 4 or better
1 GB or more
512 MB or more
15 GB or more
2 GB or more
1,024 × 768 pixels or more with 24-bit color or better
A graphics processing unit (GPU) that supports DirectX 7 or later
Built-in USB port recommended. Operation is not guaranteed other USB ports.
Internet connection (56 kbps or faster recommended) required to use FinePix Internet Service; Internet
connection and e-mail software required to use e-mail option.
Connections
* Other versions of Windows are not supported. Only pre-installed operating systems are supported; operation is not
guaranteed on home-built computers or computers that have been upgraded from earlier versions of Windows.
59
Viewing Pictures on a Computer
2 Start the computer. Log in to an account with administrator privileges before proceeding.
3 Exit any applications that may be running and insert the installer CD in a CD-ROM drive.
Windows 7/Windows Vista
If an AutoPlay dialog is displayed, click SETUP.EXE. A “User Account Control” dialog will then be displayed;
click Yes (Windows 7) or click Allow (Windows Vista).
The installer will start automatically; click Installing MyFinePix Studio and follow the on-screen
instructions to install MyFinePix Studio.
If the Installer Does Not Start Automatically
If the installer does not start automatically, select Computer or My Computer from the Start menu, then
double-click the FINEPIX CD icon to open the FINEPIX CD window and double-click SETUP or SETUP.EXE.
prompted to install Windows Media Player or DirectX, follow the on-screen instructions to
4 Ifcomplete
installation.
the installer CD from the CD-ROM drive when installation is complete. Store the installer
5 Remove
CD in a dry location out of direct sunlight in case you need to re-install the software. The
version number is printed at the top of the CD label for reference when updating the software or
contacting customer support.
Installation is now complete. Proceed to “Connecting the Camera” on page 63.
60
Viewing Pictures on a Computer
Macintosh: Installing FinePixViewer
Confirm that the computer meets the following system requirements:
1
CPU
PowerPC or Intel
Pre-installed versions of Mac OS X version 10.3.9–10.6 (for the latest information, visit http://www.fujifilm.
OS
com/)
RAM
256 MB or more
Free disk space A minimum of 200 MB required for installation with 400 MB available when FinePixViewer is running
Video
800 × 600 pixels or more with thousands of colors or better
• Built-in USB port recommended. Operation is not guaranteed other USB ports.
Other
• Internet connection (56 kbps or faster recommended) required to use FinePix Internet Service; Internet
connection and e-mail software required to use e-mail option.
starting the computer and quitting any applications that may be running, insert the installer
2 After
CD in a CD-ROM drive and double-click Installer for Mac OS X.
installer dialog will be displayed; click Installing FinePixViewer to start installation. Enter
3 An
an administrator name and password when prompted and click OK, then follow the on-screen
instructions to install FinePixViewer. Click Exit to quit the installer when installation is complete.
Connections
61
Viewing Pictures on a Computer
the installer CD from the CD-ROM drive. Note that you may be unable to remove the CD
4 Remove
if Safari is running; if necessary, quit Safari before removing the CD. Store the installer CD in a dry
location out of direct sunlight in case you need to re-install the software. The version number
is printed at the top of the CD label for reference when updating the software or contacting
customer support.
OS X 10.5 or earlier: Open the “Applications” folder, start Image Capture, and select
5 Mac
Preferences… from the Image Capture application menu. The Image Capture preferences dialog
will be displayed. Choose Other… in the When a camera is connected, open menu, then
select FPVBridge in the “Applications/FinePixViewer” folder and click Open. Quit Image Capture.
Mac OS X 10.6: Connect the camera and turn it on. Open the “Applications” folder and start
Image Capture. The camera will be listed under DEVICES; select the camera and choose
FPVBridge from the Connecting this camera opens menu and click Open. Quit Image
Capture.
Installation is now complete. Proceed to “Connecting the Camera” on page 63.
62
Viewing Pictures on a Computer
Connecting the Camera
pictures you wish to copy are stored
1 Ifonthea memory
card, insert the card into the
camera (pg. 8). If no card is inserted, pictures
will be copied from internal memory.
A Note
Windows users may require the Windows CD
when starting the software for the first time.
C Caution
Loss of power during transfer could result in loss of
data or damage to internal memory or the memory
card. Charge the battery before connecting the
camera.
the camera off and connect the supplied
2 Turn
USB cable as shown, making sure the
MyFinePix Studio or FinePixViewer will
start automatically; follow the on-screen
instructions to copy pictures to the computer.
To exit without copying pictures, click Cancel.
C Caution
If the software does not start automatically,
the software may not be correctly installed.
Disconnect the camera and reinstall the software.
For more information on using the supplied
software, start the application and select the
appropriate option from the Help menu.
Connections
connectors are fully inserted. Connect the
camera directly to the computer; do not use a
USB hub or keyboard.
the D button for about a
3 Press
second to turn the camera on.
63
Viewing Pictures on a Computer
C Cautions
• If a memory card containing a large number of
images is inserted, there may be a delay before the
software starts and you may be unable to import or
save images. Use a memory card reader to transfer
pictures.
• Make sure that the computer does not display a
message stating that copying is in progress and that
the indicator lamp is out before turning the camera
off or disconnecting the USB cable (if the number of
images copied is very large, the indicator lamp may
remain lit after the message has cleared from the
computer display). Failure to observe this precaution
could result in loss of data or damage to internal
memory or the memory card.
• Disconnect the camera before inserting or removing
memory cards.
• In some cases, it may not be possible to access
pictures saved to a network server using
the supplied software in the same way as on a
standalone computer.
• The user bears all applicable fees charged by the
phone company or Internet service provider when
using services that require an Internet connection.
64
Disconnecting the Camera
After confirming that the indicator lamp is out,
follow the on-screen instructions to turn the camera
off and disconnect the USB cable.
Uninstalling the Supplied Software
Only uninstall the supplied software when it is no
longer required or before beginning reinstallation.
After quitting the software and disconnecting
the camera, drag the “FinePixViewer” folder from
“Applications” into the Trash and select Empty Trash
in the Finder menu (Macintosh), or open the control
panel and use “Programs and Features” (Windows 7/
Windows Vista) or “Add or Remove Programs”
(Windows XP) to uninstall MyFinePix Studio. Under
Windows, one or more confirmation dialogs may be
displayed; read the contents carefully before clicking
OK.
Using the Menus: Shooting Mode
The v-mode and shooting menus contain settings for a wide range of shooting conditions.
Using the v-Mode Menu
the v button to display the
1 Press
v-MODE menu.
MODE MENU
ISO
IMAGE S ZE
FILM SIMULATION
800
4:3
the selector right to display
3 Press
options for the highlighted item.
MODE MENU
12800
6400
ISO
3200
1600
4:
800
400
EXIT
the selector up or down to
2 Press
highlight the desired menu item.
the selector up or down to
4 Press
highlight the desired option.
MENU/OK to select the
5 Press
highlighted option.
DISP/BACK to exit from the
6 Press
menu.
Menus
65
Using the Menus: Shooting Mode
v-Mode
od Menu
u Options
o s
Menu item
Descr ption
Description
n ISO
Adjust ISO sensitivity (pg. 67). Choose higher
values when the subject is poorly lit.
o IMAGE SIZE
Choose image size and aspect ratio (pg. 67).
W FILM SIMULATION
Simulate the effects of different types of film
(pg. 68).
A Note
Some options are not available in all shooting modes.
66
Options
Default
AUTO / AUTO (1600) /
AUTO (800) / AUTO (400) /
AUTO
12800 / 6400 / 3200 / 1600 /
800 / 400 / 200 / 100
o 4 : 3 / o 3 : 2 / o 16 : 9 /
p 4 : 3 / p 3 : 2 / p 16 : 9 /
o 4:3
q 4 : 3 / q 3 : 2 / q 16 : 9
c PROVIA/STANDARD /
c PROVIA/
d Velvia/VIVID / e ASTIA/SOFT /
STANDARD
N B&W / f SEPIA
Using the Menus: Shooting Mode
n ISO
Control the camera’s sensitivity to light. Higher
values can be used to reduce blur when lighting
is poor; note, however, that mottling may appear
in pictures taken at high sensitivities, particularly
at settings above 1600. If AUTO or an option
such as AUTO (1600) is selected, the camera will
adjust sensitivity automatically in response to
shooting conditions. In the case of AUTO
(1600), AUTO (800), and AUTO (400), the value
in parentheses is the maximum sensitivity that
will be selected when the subject is poorly lit.
Settings other than AUTO
are shown by an icon in the
display.
o IMAGE SIZE
Choose the size and aspect ratio at which still
pictures are recorded. Large pictures can be
printed at large sizes with no drop in quality;
small pictures require less memory, allowing
more pictures to be recorded.
Option
o 4:3
o 3:2
o 16 : 9
p 4:3
p 3:2
p 16 : 9
q 4:3
q 3:2
q 16 : 9
Prints at sizes up to
34 × 25 cm (13.5 × 10 in.)
34 × 23 cm (13.5 × 9 in.)
34 × 19 cm (13.5 × 7.5 in.)
24 × 18 cm (9.5 × 7 in.)
24 × 16 cm (9.5 × 6 in.)
24 × 13 cm (9.5 × 5.5 in.)
17 × 13 cm (7 × 5 in.)
17 × 12 cm (7 × 4.5 in.)
17 × 9 cm (7 × 3.5 in.)
Menus
The number of pictures that can be taken at
current settings (pg. 119) is displayed to the top
right in the monitor.
67
Using the Menus: Shooting Mode
Aspect Ratio
Pictures with an aspect ratio of 4 : 3 have the same
proportions as the camera display. Pictures with an
aspect ratio of 3 : 2 have the same proportions as a
frame of 35-mm film, while an aspect ratio of 16 : 9 is
suited to display on High Definition (HD) devices.
16 : 9
A Note
Image quality is not reset when the camera is turned
off or another shooting mode is selected.
68
Option
c PROVIA/
STANDARD
d Velvia/
VIVID
e ASTIA/
SOFT
N B&W
f SEPIA
4:3
3:2
W FILM SIMULATION
Simulate the effects of different types of film,
including sepia and black-and-white.
Description
Standard color reproduction. Suited
to a wide range of subjects, from
portraits to landscapes.
A high-contrast palette of saturated
colors, suited to nature photographs.
A soft-toned palette of less saturated
colors.
Take pictures in black and white.
Take pictures in sepia.
Using the Menus: Shooting Mode
Using the Shooting Menu
the selector up or down to
4 Press
highlight the desired option.
MENU/OK to display the
1 Press
shooting menu.
SHOOTING MENU
1/2
MODE
ISO
IMAGE SIZE
IMAGE QUAL TY
DYNAMIC RANGE
FILM SIMULATION
AUTO
4:3
N
AUTO
EXIT
the selector up or down to
2 Press
highlight the desired menu item.
MENU/OK to select the
5 Press
highlighted option.
DISP/BACK to exit from the
6 Press
menu.
the selector right to display
3 Press
options for the highlighted item.
SHOOTING MENU
4:3
3:2
16:9
4:3
3:2
16:9
AUTO
IMAG
N
AUTO
255 FRAMES
Menus
AUTO (L/M)
1/2
255
287
336
396
445
529
69
Using the Menus: Shooting Mode
Shooting Menu Options
Menu item
70
Description
A SCENE POSITION
Choose a scene for SP mode (pg. 23).
A SHOOTING MODE
(P/A)
A P MODE
Choose program or aperture priority AE for P
mode (pg. 28).
Choose options for O mode (pg. 21).
n ISO
Adjust ISO sensitivity (pg. 67). Choose higher
values when the subject is poorly lit.
o IMAGE SIZE
Choose image size and aspect ratio (pg. 67).
T IMAGE QUALITY
Choose image quality (pg. 72).
U DYNAMIC RANGE
Enhance details in highlights for natural contrast
(pg. 72).
W FILM SIMULATION
Simulate the effects of different types of film
(pg. 68).
Options
G/F/U/V/Y/T/K/L/D/
U/W/E/F/G/X/I/O/P
Default
P/A
P
r/s/t/u
AUTO / AUTO (1600) /
AUTO (800) / AUTO (400) /
12800 / 6400 / 3200 / 1600 /
800 / 400 / 200 / 100
o 4 : 3 / o 3 : 2 / o 16 : 9 /
p 4 : 3 / p 3 : 2 / p 16 : 9 /
q 4 : 3 / q 3 : 2 / q 16 : 9
FINE / NORMAL
AUTO / A 100% /
b 200% / C 400% /
D 800%
c PROVIA/STANDARD /
d Velvia/VIVID /
e ASTIA/SOFT /
N B&W / f SEPIA
r
G
AUTO
o 4:3
NORMAL
AUTO
c PROVIA/
STANDARD
Using the Menus: Shooting Mode
Menu item
C WHITE BALANCE
E CONTINUOUS
B PHOTOMETRY
F AF MODE
Description
Adjust color for different light sources (pg. 72).
Shoot a series of pictures (pg. 74).
Choose how the camera meters exposure (pg.
75).
Choose how the camera selects a focus area
(pg. 75).
Options
AUTO/Q/p/q/s/t/u/r/g
R/S/o/m/ OFF
Default
AUTO
OFF
N/O/P
N
w/x/T/X
w
A Note
Some options are not available in all shooting modes.
Menus
71
Using the Menus: Shooting Mode
T IMAGE QUALITY
Choose how much image files are compressed.
Select FINE (low compression) for higher image
quality, NORMAL (high compression) to increase
the number of pictures that can be stored.
U DYNAMIC RANGE
Control contrast. Higher values are
recommended for scenes that include both
sunlight and deep shade or for increased
contrast when photographing such subjects as
sunlight on water, brightly-lit autumn leaves, and
portraits taken against a blue sky; note, however,
that mottling may appear in pictures taken at
higher values. If AUTO is selected, the camera
will automatically select values between 100%
and 400% in response to shooting conditions.
A Note
D 800% is available only when U DYNAMIC
RANGE is selected in O mode and an option
other than d Velvia/VIVID or e ASTIA/SOFT is
selected for W FILM SIMULATION.
72
C WHITE BALANCE
For natural colors, choose a setting that matches
the light source (for an explanation of “white
balance,” see the Glossary on page 118).
Option
Description
AUTO White balance adjusted automatically.
Q
p
q
s
t
u
r
g
Measure a value for white balance.
For subjects in direct sunlight.
For subjects in the shade.
Use under “daylight” fluorescent lights.
Use under “warm white” fluorescent lights.
Use under “cool white” fluorescent lights.
Use under incandescent lighting.
For underwater photography.
If AUTO does not produce the desired results (for
example, when taking close-ups), select Q and
measure a value for white balance or choose the
option that matches the light source.
Using the Menus: Shooting Mode
A Notes
• At settings other than Q, auto white balance is
used with the flash. Turn the flash off (pg. 37) to take
pictures at other settings.
• Results vary with shooting conditions. Play pictures
back after shooting to check colors in the monitor.
■ Q: Custom White Balance
CUSTOM WB
Choose Q to adjust white
balance for unusual lighting
conditions. The options at
NEW WB
right will be displayed; frame a SHUTTER
NOT CHANGE
CANCEL
white object so that it fills the
monitor and press the shutter button all the way
down to measure white balance.
If “OVER” is displayed, lower exposure
compensation and try again.
B Tip
To give a deliberate color cast to your photographs,
measure a value for custom white balance using a
colored instead of a white object.
Menus
If “COMPLETED!” is displayed, press MENU/OK to
set white balance to the measured value. This
value is stored even when the battery is removed
and can be reselected by pressing MENU/OK when
custom white balance options are displayed.
If “UNDER” is displayed, raise exposure
compensation (pg. 35) and try again.
73
Using the Menus: Shooting Mode
E CONTINUOUS
Capture motion in a series of pictures.
A Notes
• The flash turns off automatically. The previouslyselected flash mode is restored when OFF is
selected for E CONTINUOUS.
• Frame rate varies with shutter speed.
■R/o
While the shutter button is pressed, the camera
takes up to 40 pictures, but only the last 23 shots
(R) or 5 shots (o) are recorded.
Up to 40 shots
Shutter button
pressed
Shutter button
released
Last 23 (R) or 5 (o) shots recorded
74
■S/m
The camera takes up to 23 (S) or 5 (m) pictures
while the shutter button is pressed.
A Notes: S / R / m / o
• Focus and exposure are determined by the first
frame in each series.
• The number of pictures that can
STORING
be recorded depends on the
memory available. Additional
time may be required to record
pictures when shooting ends.
The pictures are displayed in the
monitor while recording is in progress.
A Note: The Self-Timer
If the self-timer is used, only one picture will be taken
when R or o is selected.
Using the Menus: Shooting Mode
B PHOTOMETRY
Choose how the camera meters exposure when
Intelligent Face Detection is off.
• N MULTI: Automatic scene recognition is used
to adjust exposure for a wide range of shooting
conditions.
• O SPOT: The camera meters lighting conditions
at the center of the frame. Recommended
when the background is much brighter or
darker than the main subject. Can be used
with focus lock (pg. 32) to meter off-center
subjects.
• P AVERAGE: Exposure is set to the average for
the entire frame. Provides consistent exposure
across multiple shots with the same lighting,
and is particularly effective for landscapes and
portraits of subjects dressed in black or white.
F AF MODE
This option controls how the camera selects the
focus area. Regardless of the option selected,
the camera will focus on the subject in the
center of the monitor when macro mode is on
(pg. 36).
• w CENTER: The camera
focuses on the subject in
the center of the frame. This
option can be used with
focus lock.
• x MULTI: When the shutter button is pressed
halfway, the camera detects high-contrast
subjects near the center of the frame and
selects the focus area automatically (if the focus
frame is not displayed, select w CENTER and
use focus lock; pg. 32).
Menus
Press
halfway
250
F3.3
Focus frame
75
Using the Menus: Shooting Mode
• T CONTINUOUS: While the
shutter button is pressed
halfway, the camera
continuously adjusts focus to
reflect changes in the
distance to the main subject in the focus frame
(note that this increases the drain on the
battery and that the sound of the camera
focusing will be audible). Choose this option
when photographing moving subjects.
• X TRACKING: When X is set, the focus frame
is displayed in the center of the monitor as
shown. Place the subject in the focus frame
and press the G button to set TRACKING.
The focus frame will track the moving subject,
keeping it in focus.
S FACE RECOGNITION
Once personal information is registered with
a face, the camera recognizes the registered
face and prioritizes focus and exposure to that
face. When playing back the face, the registered
information (name, birthday, etc.) can be
displayed.
■ Activating S FACE RECOGNITION
S FACE RECOGNITION from
1 Select
shooting menu to display options.
FACE RECOGNITION
FACE RECOGNITION
REGISTER
VIEW & ED T
ERASE
AUTO REGISTRATION
ON
ON
BACK
the selector up or down to
2 Press
highlight FACE RECOGNITION.
START TRACKING
CANCEL
A Note
TRACKING may not work depending on the subject.
76
3 Press MENU/OK to display options.
Using the Menus: Shooting Mode
the selector up or down to
4 Press
highlight ON.
MENU/OK to display PERSONAL
4 Press
INFO.
PERSONAL INFO
MENU/OK to activate S FACE
5 Press
RECOGNITION.
NAME
BIRTHDAY
CATEGORY
■ REGISTER
BACK
Shooting
REGISTER from S FACE
1 Select
RECOGNITION.
MENU/OK to turn to shooting
2 Press
mode.
3
2050. 12. 31
NONE
Press the shutter button to shoot.
Capture a front face.
REGISTER FACE
A Note
When the message !CANNOT REGISTER is displayed,
the camera has failed to register the face. Take a shot
again.
Registering a name
the selector up or down to
1 Press
highlight NAME in PERSONAL
INFO.
NAME
CAPTURE THE FACE
ALONG WITH THE GUIDL NE
Menus
MENU/OK to display NAME
2 Press
window.
CANCEL
SET
INPUT
CANCEL
77
Using the Menus: Shooting Mode
the selector left, right, up or
3 Press
down to highlight a letter.
4 Press MENU/OK to input the letter.
from step 2 to step 4 to input a
5 Repeat
name.
the selector left, right, up or
6 Press
down to highlight SET.
7 Press MENU/OK to register.
A Notes
• Highlight DEL and press MENU/OK to erase a letter.
• Highlight g and press MENU/OK to put a space.
• Up to 14 letters can be displayed.
Registering a birthday
the selector up or down to
1 Press
highlight BIRTHDAY in PERSONAL
INFO.
78
2 Press MENU/OK to display BIRTHDAY.
the date of birthday in the same way
3 Input
as setting e DATE/TIME (pg. 12).
4 Press MENU/OK to register.
A Note
If shooting date matches the birthday of the peson
with the green border during face zoom, Happy
Birthday! will be displayed with the name.
Registering a category
the selector up or down
1 Press
to highlight CATEGORY in
PERSONAL INFO.
FAMILY
FRIEND
NAME
PARTNER
BIRTHD
NONE
CATEGO
the selector up or down to
2 Press
highlight a category.
Using the Menus: Shooting Mode
3 Press MENU/OK to register.
the registration or edit as the same
4 View
way of REGISTER (pg. 77).
■ VIEW & EDIT
A Note
Select REPLACING IMAGE to take another face image
and replace the registered image with it.
VIEW & EDIT from S FACE
1 Select
RECOGNITION to display REGISTERED
FACE.
REGISTERED FACE
SET
2
■ ERASE
1 Select ERASE from S FACE RECOGNITION.
the selector left or right to
2 Press
highlight a face to erase.
TARO
BACK
Press the selector left or right to
highlight a face to view or edit.
MENU/OK to display PERSONAL
3 Press
INFO.
MENU/OK to display ERASE
3 Press
window.
ERASE THE INFO OK?
TAKU
2050. 12. 31
FAMILY
OK
CANCEL
SET
NAME
BIRTHDAY
2050. 12. 31
CATEGORY
NONE
REPLACING IMAGE
the selector up or down to
4 Press
highlight OK.
Menus
PERSONAL INFO
BACK
79
Using the Menus: Shooting Mode
MENU/OK to delete a
5 Press
registration.
■ AUTO REGISTRATION
Select AUTO REGISTRATION from S FACE
RECOGNITION and set it to ON. After
shooting the same face several times with
3 FACE DETECTION turned on, the camera
automatically recognizes the face.
A Notes
• When the camera recognizes a face that has
been shot many times, the message REGISTER
THIS PERSON? appears. Press MENU/OK to display
PERSONAL INFO so that you can register the face
and its personal information.
• Using only AUTO REGISTRATION may be difficult
to recognize a face. In that case, register a face and
its personal information from REGISTER.
80
S FACE RECOGNITION
• Up to 8 people’s information can be registered. If
8 people’s information has already been registered,
the confirmation window appears when trying to
add a new one. Delete a registered person from
VIEW & EDIT and register the new person.
• When 8 people’s information has already been
registered, AUTO REGISTRATION does not
function.
• If the camera detects two or more faces registered
by S FACE RECOGNITION, a green border and
orange border(s) will be displayed on the faces
when to shoot. A registered name will appear only
on the face with the green border. White borders
will be displayed on faces which have not been
registered. When no name has been registered,
“---” is displayed.
C Caution
S FACE RECOGNITION may not function in the
following:
• the subject does not face front.
• the face is not positioned within a frame.
• the feature of the face varies (because of age or
expression).
Using the Menus: Playback Mode
The v-MODE and playback menus are used to manage the pictures in internal memory or on the
memory card.
Using the v-Mode Menu
the D button to enter
1 Press
playback mode (pg. 11).
MENU/OK to select the
6 Press
highlighted option.
the v button to display the
2 Press
v-MODE menu.
v-Mode Menu Options
MODE MENU
SLIDE SHOW
PRINT ORDER (DPOF)
Option
Description
q SLIDE SHOW View pictures in a slide show (pg. 82).
r PRINT ORDER Select pictures for printing on DPOF- and
PictBridge-compatible devices (pg. 57).
(DPOF)
EXIT
the selector up or down to
3 Press
highlight the desired menu item.
the selector up or down to
5 Press
highlight the desired option.
Menus
the selector right to display
4 Press
options for the highlighted item.
81
Using the Menus: Playback Mode
q SLIDE SHOW
View pictures in an automated slide show.
Choose the type of show and press MENU/OK
to start. Press DISP/BACK at any time during
the show to view on-screen help. When a
movie is displayed, movie playback will begin
automatically, and the slide show will continue
when the movie ends. The show can be ended
at any time by pressing MENU/OK.
Option
Displayed in
Press selector left or right to go back or
skip ahead one frame. Select FADE-IN
FADE-IN for fade transitions between frames.
As above, except that camera
NORMAL B
automatically zooms in on faces
selected with Intelligent Face
FADE-IN B
detection.
MULTIPLE Display several pictures at once.
NORMAL
A Note
The camera will not turn off automatically while a
slide show is in progress.
82
Using the Menus: Playback Mode
Using the Playback
y
Menu
D to enter playback mode
1 Press
(pg. 11).
PLAYBACK MENU
MENU/OK to display the
2 Press
playback menu.
PLAYBACK MENU
the selector right to display
4 Press
options for the highlighted item.
1 /3
IMAGE SEARCH
ERASE
SLIDE SHOW
RED EYE REMOVAL
PROTECT
CROP
EXIT
the selector up or down to
3 Press
highlight the desired menu item.
1 /3
IMAG
BACK
ERAS
SLIDE FRAME
RED ALL FRAMES
PROT
CROP
the selector up or down to
5 Press
highlight the desired option.
MENU/OK to select the
6 Press
highlighted option.
Menus
83
Using the Menus: Playback Mode
Playback
y
Menu Options
The following options are available:
Option
V IMAGE SEARCH
M ERASE
q SLIDE SHOW
a RED-EYE REMOVAL
O PROTECT
R CROP
j RESIZE
N IMAGE ROTATE
P COPY
Q VOICE MEMO
S ERASE FACE RECOG.
r PRINT ORDER (DPOF)
J DISP ASPECT
84
Description
Search images based on categories (pg. 44).
Delete all or selected pictures (pg. 46).
View pictures in a slide show (pg. 82).
Create copies with reduced red eye (pg. 85).
Protect pictures from accidental deletion (pg. 85).
Create cropped copies of pictures (pg. 86).
Create small copies of pictures (pg. 87).
Rotate pictures (pg. 88).
Copy pictures between internal memory and a memory card (pg. 89).
Add voice memos to pictures (pg. 90).
Erase personal information registered with a face that has been selected (pg. 92).
Select pictures for printing on DPOF- and PictBridge-compatible devices (pg. 57).
Choose a display mode for viewing photographs on an HDTV (pg. 52; available when an HDMI
cable is connected) (pg. 92).
Using the Menus: Playback Mode
a RED EYE REMOVAL
If the current picture is marked with a B icon
to indicate that it was taken with Intelligent Face
Detection, this option can be used to remove
red-eye. The camera will analyze the image; if
red-eye is detected, the image will be processed
to create a copy with reduced red-eye.
REMOV NG
O PROTECT
Protect pictures from accidental deletion. The
following options are available.
■ FRAME
Protect selected pictures.
the selector left or right to
1 Press
display the desired picture.
PROTECT OK?
YES
CANCEL
Picture not protected
YES
CANCEL
Protected picture
MENU/OK to protect the
2 Press
picture. If the picture is already
protected, pressing MENU/OK will
remove protection from the image.
steps 1–2 to protect
3 Repeat
additional images. Press DISP/BACK
Menus
A Notes
• Red eye may not be removed if the camera is unable
to detect a face or the face is in profile. Results may
differ depending on the scene. Red eye can not
be removed from pictures that have already been
processed using red-eye removal or pictures created
with other devices.
• The amount of time needed to process the image
varies with the number of faces detected.
• Copies created with a RED EYE REMOVAL are
indicated by a l icon during playback.
UNPROTECT OK?
to exit when the operation is
complete.
85
Using the Menus: Playback Mode
■ SET ALL
Press MENU/OK to protect all
pictures, or press DISP/BACK to
exit without changing picture
status.
■ RESET ALL
Press MENU/OK to remove
protection from all pictures, or
press DISP/BACK to exit without
changing picture status.
SET ALL OK?
IT MAY TAKE A WHILE
YES
CANCEL
RESET ALL OK?
IT MAY TAKE A WHILE
YES
CANCEL
If the number of pictures
affected is very large, the
display at right will appear
in the monitor while the
CANCEL
operation is in progress.
Press DISP/BACK to exit before the operation is
complete.
C Caution
Protected pictures will be deleted when the memory
card or internal memory is formatted (pg. 97).
86
R CROP
To create a cropped copy of a picture, play
the picture back and select R CROP in the
playback menu.
the zoom control to zoom in and out and
1 Use
use the selector to scroll the picture until the
desired portion is displayed (to exit to singleframe playback without creating a cropped
copy, press DISP/BACK).
CROP
YES
Zoom indicator
CANCEL
Navigation window
shows portion of
image currently
displayed in monitor
If the size of the final copy will be t, OK
will be displayed in yellow.
Using the Menus: Playback Mode
B Tip: Intelligent Face Detection
If the picture was shot with
Intelligent Face Detection (pg.
30), B will be displayed in the
monitor. Press the B button
to zoom in on the selected
face.
j RESIZE
To create a small copy of a picture, play the
picture back and select j RESIZE in the
playback menu.
CROP
CROP
YES
CANCEL
MENU/OK. A confirmation
2 Press
dialog will be displayed.
the selector up or down to
1 Press
highlight p, q, or t.
MENU/OK to select the
2 Press
highlighted option.
REC OK?
MENU/OK to copy the picture at
3 Press
the selected size.
REC
CANCEL
Copy size is shown at the top. Larger crops
produce larger copies; all copies have an
aspect ratio of 4 : 3.
Available resized file size varies depending on the
size of an original file.
Original file size
Available resized file size
o
p, q, t
p
q, t
t
q
Menus
MENU/OK to save the cropped
3 Press
copy to a separate file.
A Note
87
Using the Menus: Playback Mode
N IMAGE ROTATE
IMAGE ROTATE
By default, pictures taken in
tall orientation are displayed
in wide orientation. Use this
option to display pictures in
SET
CANCEL
the correct orientation in the
monitor. It has no effect on pictures displayed
on a computer or other device.
the selector down to
1 Press
rotate the picture 90 ° clockwise,
up to rotate the picture 90 °
counterclockwise.
A Notes
• Protected pictures can not be rotated. Remove
protection before rotating pictures (pg. 85).
• The camera may not be able to rotate pictures
created with other devices.
To rotate a picture, play the picture back and
select N IMAGE ROTATE in the playback menu.
MENU/OK to confirm the
2 Press
operation (to exit without rotating
the picture, press DISP/BACK).
The next time the picture is played back, it will
automatically be rotated.
88
Using the Menus: Playback Mode
P COPY
Copy pictures between internal memory and a
memory card.
the selector up or down to
1 Press
highlight d INTERNAL MEMORY
g x CARD (copy pictures from
internal memory to the memory card) or
x CARD g d INTERNAL MEMORY (copy
pictures from a memory card to internal
memory).
the selector right to display
2 Press
options for the highlighted item.
COPY
NTE FRAME
CAR ALL FRAMES
■ FRAME
Copy selected frames.
COPY OK?
100 0001
YES
CANCEL
the selector left or right to
1 Press
display the desired picture.
2 Press MENU/OK to copy the picture.
steps 1–2 to copy additional
3 Repeat
images. Press DISP/BACK to exit
when the operation is complete.
Menus
3
Press the selector up or down to
highlight FRAME or ALL FRAMES.
B Tip: Copying Pictures Between Memory Cards
To copy pictures between two memory cards, insert
the source card and copy the pictures to internal
memory, then remove the source card, insert the
destination card, and copy the pictures from internal
memory.
4 Press MENU/OK.
89
Using the Menus: Playback Mode
■ ALL FRAMES
Press MENU/OK to copy all
pictures, or press DISP/BACK to
exit without copying pictures.
COPY ALL OK?
100 0001
IT MAY TAKE
A WHILE
YES
CANCEL
C Cautions
• Copying ends when the destination is full.
• DPOF print information is not copied (pg. 56).
Q VOICE MEMO
To add a voice memo to a
still picture, select Q VOICE
MEMO after displaying the
picture in playback mode.
30s
REC STANDBY
START
CANCEL
A Note
Voice memos can not be added to movies or
protected pictures. Remove protection from pictures
before recording voice memos (pg. 85).
the camera at a distance of about 20 cm
1 Hold
(8 in.) and face the microphone.
Microphone
2 Press MENU/OK to start recording.
28s
RECORDING
Time remaining
Blinks red
REC
90
RE REC
Using the Menus: Playback Mode
MENU/OK again to end
3 Press
recording. Recording ends
automatically after 30 seconds.
F NISH
REC
RE REC
A Notes
PLAYBACK MENU
1
• If a voice memo already
RESIZ
exists for the current picture,
IMAG
BACK
COPY
RE REC
VOIC
the options at right will be
ERAS
PRINT
displayed. Select RE-REC to
replace the existing memo.
• Voice memos are recorded as PCM-format WAV files.
/3
Playing Voice Memos
Pictures with voice memos are indicated by a h
icon during playback. To play the voice memo, press
the selector down. To pause, press the selector
down again; to end playback, press the selector up.
Press the selector left to rewind, right to fast forward.
Volume controls can be displayed by pressing the
MENU/OK button; press the selector up or down
to adjust the volume, and press MENU/OK again to
resume playback.
15s Progress is shown
in the monitor.
STOP
PAUSE
Progress bar
A Note
The camera may not play voice memos recorded
with other devices.
Menus
C Caution
Do not cover the speaker during playback.
Speaker
91
Using the Menus: Playback Mode
S ERASE FACE RECOG.
While playing back an image
including faces registered with
personal information, select
NEXT
S ERASE FACE RECOG.
ERASE
CANCEL
to enlarge a registered face.
Press MENU/OK to erase the personal information.
A Note
Personal information cannot be erased when the
image size is t.
92
J DISP ASPECT
Choose the aspect ratio used when photographs
with at a 4 : 3 aspect ratio (pg. 68) are viewed on
a High Definition device (pg. 52). This option is
available when an HDMI cable is connected.
• 16 : 9: The image fills the screen, with the top
and bottom cropped out.
• 4 : 3: The entire image is displayed, with black
bands at the right and left sides.
Photographs with an aspect ratio of 16 : 9 are
displayed full screen, those with an aspect ratio
of 3 : 2 in a black frame.
The Setup Menu
Using the Setup Menu
the setup menu.
1 Display
1.1 Press MENU/OK to display the
Adjust settings.
2 2.1
Press the selector right to
menu for the current mode.
activate the setup menu.
1.2 Press the selector left to
highlight a left tab.
2.2 Press the selector up or down
to highlight a menu item.
1.3 Press the selector up or down
to select 4.
The setup menu appears.
SET UP
1 /4
SET UP
IMAGE DISP.
FRAME NO.
OPERATION VOL.
SHUTTER VOLUME
SHUTTER SOUND
PLAYBACK VOLUME
2 /4
1.5 SEC
CONT.
EXIT
DATE/TIME
TIME DIFFERENCE
SILENT MODE
RESET
FORMAT
EXIT
ENGLISH
OFF
2.3 Press the selector right
to display options for the
highlighted item.
2.5 Press MENU/OK to select the
highlighted option.
2.6 Press DISP/BACK to exit from the
menu.
Menus
2.4 Press the selector up or down
to highlight an option.
93
The Setup Menu
Setup Menu Options
Menu item
e DATE/TIME
p TIME DIFFERENCE
nw
7 SILENT MODE
1/4
s RESET
m FORMAT
a IMAGE DISP.
b FRAME NO.
d OPERATION VOL.
2/4
e SHUTTER VOLUME
f SHUTTER SOUND
g PLAYBACK VOLUME
94
Description
Set the camera clock.
Set the clock to local time (pg. 96).
Choose a language.
Turn off the speaker, flash, and AF-assist illuminator/selftimer lamp.
Reset all settings except DATE/TIME, TIME DIFFERENCE,
BACKGROUND COLOR, and VIDEO SYSTEM to default values. A
confirmation dialog will be displayed, press the selector
left or right to highlight OK and press MENU/OK.
Format internal memory or memory cards (pg. 97).
Choose how long pictures are displayed after shooting
(pg. 97).
Choose how files are named (pg. 98).
Adjust the volume of camera controls.
Adjust the volume of the shutter sound.
Choose the sound made by the shutter.
Adjust the volume for movie and voice memo playback
(pg. 99).
Options
—
k/j
See page 122
Default
—
k
ENGLISH
ON / OFF
OFF
—
—
—
—
3 SEC / 1.5 SEC /
1.5 SEC
ZOOM (CONTINUOUS) / OFF
CONTINUOUS / RENEW
CONTINUOUS
q (high) / m (mid) /
m
n (low) / EOFF (mute)
2
2/3
—
7
The Setup Menu
Menu item
g LCD BRIGHTNESS
o AUTO POWER OFF
Description
Control the brightness of the display (pg. 99).
Choose the auto power off delay (pg. 99).
Reduce blur. Choose whether the function is performed
at all times when the camera is in the shooting mode
Z DUAL IS MODE
(k CONTINUOUS), only when the shutter button is
3/4
pressed halfway (l SHOOTING ONLY) or OFF.
Remove “red-eye” effects caused by the flash.
a RED EYE REMOVAL
Enable or disable digital zoom (pg. 100).
c DIGITAL ZOOM
Turn the AF-assist illuminator on or off (pg. 34).
b AF ILLUMINATOR
Choose whether to save unprocessed copies of
pictures taken using a RED EYE REMOVAL, F PRO
H SAVE ORG IMAGE
LOW-LIGHT, or G PRO FOCUS. Select ON to save
unprocessed copies.
Choose ON to automatically rotate “tall” (portraitZ AUTOROTATE PB
orientation) pictures during playback.
4/4
q BACKGROUND COLOR Choose a color scheme for menus and cursors.
Choose whether to display tool tips.
u GUIDANCE DISPLAY
Choose a video mode for connection to a TV (pg. 52).
r VIDEO SYSTEM
Optimize camera performance for increased battery life,
m POWER MANAGEMENT
quick focus, or display quality (pg. 101).
Options
—
5 MIN / 2 MIN / OFF
Default
0
2 MIN
k CONTINUOUS /
l SHOOTING ONLY /
OFF
k
ON / OFF
ON / OFF
ON / OFF
ON
OFF
ON
ON / OFF
OFF
ON / OFF
ON
—
ON / OFF
NTSC / PAL
BLUE
ON
—
v/w/x
v
Menus
95
The Setup Menu
p TIME DIFFERENCE
When traveling, use this option to switch the camera clock instantly from your home time zone to the
local time at your destination.
the difference between local time
1 Specify
and your home time zone.
1.1 Press the selector up or down
to highlight j LOCAL.
1.2 Press the selector right to
display the time difference.
TIME DIFFERENCE
12 / 31 / 2050 10:00 AM
12 / 31 / 2050 10:00 AM
01
00
between local time and your
2 Switch
home time zone.
To set the camera clock to local time,
highlight j LOCAL and press MENU/OK.
To set the clock to the time in your home
time zone, select k HOME. If j LOCAL
is selected, j will be displayed in the
monitor for three seconds after the camera
enters shooting mode, and the date will be
displayed in yellow.
00
23
SET
CANCEL
1.3 Press the selector left or right
to highlight +, –, hours, or
minutes; press up or down to
edit. The minimum increment
is 15 minutes.
1.4 Press MENU/OK when settings
are complete.
96
2 / 31 / 2050
10 : 00 AM
After changing time zones, check that the
date and time are correct.
The Setup Menu
m FORMAT
FORMAT
Format internal memory or a
FORMAT OK?
ERASE ALL DATA
memory card. If a memory
OK
card is inserted in the camera,
CANCEL
x will be displayed in the
SET
dialog shown at right and
this option will format the memory card. If no
memory card is inserted, d will be displayed
and this option will format internal memory.
Highlight OK and press MENU/OK to begin
formatting.
C Cautions
• All data—including protected pictures—will be
deleted. Be sure important files have been copied to
a computer or other storage device.
• Do not open the battery cover during formatting.
Menus
a IMAGE DISP.
Choose how long pictures are displayed in the
monitor after shooting.
• 3 SEC: Pictures are displayed for about 3 s before
being recorded to the memory card.
• 1.5 SEC: Pictures are displayed for about 1.5 s
before being recorded to the memory card.
• ZOOM (CONTINUOUS): Pictures are displayed until
the MENU/OK button is pressed. Pictures can be
zoomed in to check fine details.
When the picture is zoomed in, the selector
can be used to view areas of the image not
currently visible in the display.
When the picture was taken with 3 FACE
DETECTION turned on, or taken in the
Y DOG or T CAT mode, a detected face is
zoomed. When two or more faces have been
detected, you can move to the next face by
pressing B.
97
The Setup Menu
ZOOM (CONTINUOUS) is disabled in the following
case:
- A, G or F is selected in the shooting
mode.
- An option other than OFF is selected for
E CONTINUOUS.
A Notes
• Pictures taken in continuous shooting modes are
always displayed after shooting.
• The colors displayed at settings of 1.5 SEC and
3 SEC may differ from those in the final picture.
98
b FRAME NO.
New pictures are stored in
Frame number
100 0001
image files named using
a four-digit file number
Directory
File
assigned by adding one to
number
number
the last file number used.
The file number is displayed during playback as
shown at right. FRAME NO. controls whether
file numbering is reset to 0001 when a new
memory card is inserted or the current memory
card or internal memory is formatted.
• CONTINUOUS: Numbering continues from the
last file number used or the first available file
number, whichever is higher. Choose this
option to reduce the number of pictures with
duplicate file names.
• RENEW: Numbering is reset to 0001 after
formatting or when a new memory card is
inserted.
The Setup Menu
A Notes
• If the frame number reaches 999-9999, the shutter
release will be disabled (pg. 116).
• Selecting s RESET (pg. 94) resets b FRAME
NO. to CONTINUOUS but does not reset frame
numbering.
• Frame numbers for pictures taken with other
cameras may differ.
g PLAYBACK VOLUME
Press the selector up or down
to choose volume for movie
and voice memo playback and
press MENU/OK to select.
g LCD BRIGHTNESS
Press the selector up or down
to choose display brightness
and press MENU/OK to select.
VOLUME
7
SET
CANCEL
o AUTO POWER OFF
Choose the length of time before the camera
turns off automatically when no operations
are performed. Shorter times increase battery
life; if OFF is selected, the camera must be
turned off manually. Note that regardless of the
option selected, the camera will not turn off
automatically when connected to a printer (pg.
54) or computer (pg. 59) or when a slide show is
in progress (pg. 82).
B Tip: Reactivating the Camera
To reactivate the camera after it has turned off
automatically, use the n button or press the D
button for about a second (pg. 11).
LCD BRIGHTNESS
0
CANCEL
Menus
SET
99
The Setup Menu
A Note
Although OFF is selected for o AUTO POWER OFF,
the camera will turn off automatically if no operations
are performed for five minutes in the following case:
• w QUICK AF or x CLEAR DISPLAY is selected for
m POWER MANAGEMENT.
• r is selected in P MODE.
• STANDBY is displayed in A.
• B is displayed in the shooting mode.
• G, V, Y, or T is selected in the shooting
mode.
c DIGITAL ZOOM
If ON is selected, selecting A at the maximum
optical zoom position will trigger digital zoom,
further magnifying the image. To cancel digital
zoom, zoom out to the minimum digital zoom
position and select B.
Zoom
indicator
Zoom indicator,
DIGITAL ZOOM off
B
Zoom indicator,
DIGITAL ZOOM on
A B
Optical zoom
Optical zoom
A
Digital
zoom
C Caution
Digital zoom produces lower quality images than
optical zoom.
100
The Setup Menu
m POWER MANAGEMENT
Optimize camera performance for increased
battery life, quick focus response, or improved
display quality. The following options are
available:
• v POWER SAVE: Monitor refresh rate is reduced.
If no operations are performed for 10 s,
the monitor will dim automatically to save
power. This option is recommended when
the camera is used for extended periods at
high temperatures to prevent mottled vertical
streaks from appearing in photographs.
• w QUICK AF: Reduces focusing time, ensuring a
quick shutter response.
• x CLEAR DISPLAY: Choose this option for a
brighter, higher quality display.
A Notes
• v POWER SAVE does not take effect when
Intelligent Face Detection is on.
• At settings other than v POWER SAVE, the
monitor will dim automatically if no operations are
performed for 30 s.
Menus
101
Optional Accessories
The camera supports a wide range of accessories from FUJIFILM and other manufacturers.
■ Computer Related
■ Audio/Visual
TV*
USB
Audio/visual
output
HDTV*
Computer*
HDMI
cable*
HD player
SD/SDHC
memory card
Technical Notes
HDMI
cable*
■ Printing
Printer*
USB
PictBridge-compatible printer*
* Available from third-party suppliers.
102
SD card slot or card reader
Optional Accessories
Accessories from FUJIFILM
The following optional accessories are available from FUJIFILM. For the latest information on the
accessories available in your region, check with your local FUJIFILM representative or visit http://www.
fujifilm.com/products/digital_cameras/index.html.
Rechargeable
Li-ion battery
NP-50 (supplied)
Additional NP-50 large-capacity batteries can be
purchased as required.
Battery charger
BC-45W (supplied)
Replacement battery chargers can be purchased
as required. The BC-45W charges an NP-50
battery in about 150 minutes at +20 °C (+68 °F).
Use for extended playback or when copying
pictures to a computer (shape of adapter and
plug vary with region of sale).
DC coupler
CP-50
Connect the AC-5VX to the camera.
HD player
HDP-L1
Still pictures and movies in SD card can be
viewed by HDTV (requires HDMI cable, available
from third-party suppliers).
Waterproof case
WP-FXF80
Allows the camera to be used at depths of up to
40 m (131 ft.). Camera controls can be adjusted
and the flash can be used without removing the
camera from the case.
Technical Notes
AC power adapter AC-5VX (requires
CP-50)
103
Caring for the Camera
To ensure continued enjoyment of the product, observe the following precautions.
Storage and Use
If the camera will not be used for an extended
period, remove the battery and memory card. Do
not store or use the camera in locations that are:
• exposed to rain, steam, or smoke
• very humid or extremely dusty
• exposed to direct sunlight or very high
temperatures, such as in a closed vehicle on a
sunny day
• extremely cold
• subject to strong vibration
• exposed to strong magnetic fields, such as
near a broadcasting antenna, power line, radar
emitter, motor, transformer, or magnet
• in contact with volatile chemicals such as
pesticides
• next to rubber or vinyl products
■ Water and Sand
Exposure to water and sand can also damage the
camera and its internal circuitry and mechanisms.
When using the camera at the beach or seaside,
avoid exposing the camera to water or sand. Do
not place the camera on a wet surface.
104
■ Condensation
Sudden increases in temperature, such as occur
when entering a heated building on a cold day,
can cause condensation inside the camera. If
this occurs, turn the camera off and wait an hour
before turning it on again. If condensation forms
on the memory card, remove the card and wait
for the condensation to dissipate.
Cleaning
Use a blower to remove dust from the lens and
monitor, then gently wipe with a soft, dry cloth.
Any remaining stains can be removed by wiping
gently with a piece of FUJIFILM lens-cleaning
paper to which a small amount of lens-cleaning
fluid has been applied. Care should be taken to
avoid scratching the lens or monitor. The camera
body can be cleaned with a soft, dry cloth.
Do not use alcohol, thinner, or other volatile
chemicals.
Traveling
Keep the camera in your carry-on baggage.
Checked baggage may suffer violent shocks that
could damage the camera.
Troubleshooting
Power and Battery
Problem
Possible cause
The battery is exhausted.
The battery is not in the correct
The camera does orientation.
not turn on.
The battery-chamber cover is not latched.
The AC adapter and DC coupler are not
connected properly.
Power
supply
Page
5, 14
6
7
—
—
—
21
—
—
75
5, 14
—
Troubleshooting
Solution
Insert a fresh or fully-charged spare battery.
Re-insert the battery in the correct
orientation.
Latch the battery-chamber cover.
Make sure that the AC adapter and DC
coupler are properly connected.
Warm the battery by placing it in a pocket
The battery is cold.
or other warm place and re-insert it in the
camera immediately before taking a picture.
There is dirt on the battery terminals.
Clean the terminals with a soft, dry cloth.
Select another shooting mode.
The camera is in r mode.
The battery runs
The battery has reached the end of its
down quickly.
The battery has been charged many times.
charging life. Purchase a new battery.
w QUICK AF or x CLEAR DISPLAY is
Select v POWER SAVE to reduce the drain
selected for m POWER MANAGEMENT. on the battery.
T CONTINUOUS or X TRACKING is
Select a different AF mode.
selected for F AF MODE.
The battery is exhausted.
Insert a fresh or fully-charged spare battery.
The camera turns
The AC adapter or DC coupler has been
Make sure that the AC adapter and DC
off suddenly.
disconnected.
coupler are properly connected.
105
Troubleshooting
Problem
Battery
charger
Possible cause
The battery is not correctly inserted.
Charging does
The battery is not in the correct
not start.
orientation.
Charging is slow. The temperature is low.
There is dirt on the battery terminals.
Solution
Re-insert the battery in the charger.
Re-insert the battery in the correct
orientation.
Charge the battery at room temperature.
Clean the terminals with a soft, dry cloth.
The battery has reached the end of its
The charging
charging life. Purchase a new battery. If
lamp lights, but The battery has been charged many times.
the battery still fails to charge, contact your
the battery does
FUJIFILM dealer.
not charge.
The charger is not correctly plugged into a Plug the charger correctly into the power
power outlet.
outlet.
Page
5
5
—
—
—
—
Menus and Displays
Problem
Menus and displays are
not in English.
106
Possible cause
English is not selected for the
n w option in the setup menu.
Solution
Select ENGLISH.
Page
12, 94
Troubleshooting
Shooting
Problem
Possible cause
Memory is full.
Memory is not formatted.
No picture is
taken when the There is dirt on the memory card contacts.
shutter button is The memory card is damaged.
Taking
pressed.
The battery is exhausted.
pictures
The camera has turned off automatically.
The monitor
goes dark after The flash has fired.
shooting.
The subject is close to the camera.
The camera does
Focus
The subject is far away from the camera.
not focus.
The subject is not suited to autofocus.
Image size varies
EXR AUTO
S is selected for o IMAGE SIZE.
from shot to shot.
Solution
Page
Insert a new memory card or delete pictures. 8, 46
Format the memory card or internal memory. 97
Clean the contacts with a soft, dry cloth.
—
Insert a new memory card.
8
Insert a fresh or fully-charged spare battery.
6
Turn the camera on.
11
The monitor may darken while the flash
charges. Wait for the flash to charge.
Select macro mode.
Cancel macro mode.
Use focus lock.
37
36
32
Select another image size or shooting mode. 21, 67
Troubleshooting
107
Troubleshooting
Problem
Face detection
not available.
Intelligent
Face
Detection No face is
detected.
Wrong subject
selected.
Macro mode is
Close-ups
not available.
108
Possible cause
Solution
Page
Intelligent Face Detection is not available
Choose a different shooting mode.
21
in the current shooting mode.
X TRACKING is selected for F AF
Select a different AF mode.
75
MODE.
The subject’s face is obscured by
Remove the obstructions.
sunglasses, a hat, long hair, or other objects.
The subject’s face occupies only a small
Change the composition so that the subject’s
30
area of the frame.
face occupies a larger area of the frame.
The subject’s head is at an angle or the
Ask the subject to face the camera and hold
subject is not facing the camera.
their head straight.
The camera is tilted.
Hold the camera straight.
16
The subject’s face is poorly lit.
Shoot in bright light.
—
The selected subject is closer to the center Recompose the picture or turn face detection
30, 32
of the frame than the main subject.
off and frame the picture using focus lock.
Macro mode is not available in the current
Choose a different shooting mode.
21
shooting mode.
Troubleshooting
Problem
Flash
AC adapter
Possible cause
The flash is charging.
The flash is not available in the current
shooting mode.
The flash does
not fire.
The battery is exhausted.
An option other than OFF is selected for
E CONTINUOUS.
The desired flash mode is not available in
Flash mode not
the current shooting mode.
available.
The camera is in silent mode.
The subject is not in range of the flash.
The flash does
not fully light the The flash window is obstructed.
subject.
Fast shutter speed selected.
Help text is
displayed.
The camera was turned on while being
powered by an AC adapter.
Solution
Wait for the flash to charge.
Page
37
Choose a different shooting mode.
21
Insert a fresh or fully-charged spare battery.
6
Turn E CONTINUOUS off.
74
Choose a different shooting mode.
21
Turn silent mode off.
Position the subject in range of the flash.
Hold the camera correctly.
Choose a slower shutter speed.
Follow the on-screen instructions to enter
demo mode or press the shutter button to
cancel.
19
122
16
27
—
Troubleshooting
109
Troubleshooting
Problem
Pictures are
blurred.
Problem
images
Pictures are
mottled.
Vertical lines
appear in
pictures.
Possible cause
The lens is dirty.
The lens is blocked.
R is displayed during shooting and the
focus frame is displayed in red.
0 is displayed during shooting.
Slow shutter speed selected and the
subject is poorly lit.
Recording
Pictures are not
recorded.
Continuous
Only one picture The self-timer is on and R or o is
is taken.
selected for E CONTINUOUS.
Power was interrupted during shooting.
Page
104
16
Check focus before shooting.
18
Use the flash or a tripod.
38
Choose a faster shutter speed.
27
The camera has been used continuously at Turn the camera off and wait for it to cool
high temperatures.
down.
Smear appears in The sun or another bright object was in
pictures.
the frame.
110
Solution
Clean the lens.
Keep objects away from the lens.
White or purple vertical lines may appear
when a very bright object is framed in the
display. This is normal and does not indicate
a malfunction. Smear is not recorded in
photographs but may appear in movies. If
possible, avoid shooting movies with bright
objects in or close to the frame.
Turn the camera off before connecting the
AC adapter/DC coupler. Leaving the camera
on can result in corrupted files or damage to
the memory card or internal memory.
Turn the self-timer off.
—
48
—
39
Troubleshooting
Movie
Problem
Possible cause
T CONTINUOUS is selected for F AF
The sound of
MODE.
Recording camera focusing
Zoom in or out while recording a movie.
is heard.
Intelligent Face Detection is on.
Solution
Page
Select w CENTER for F AF MODE.
50
Stop zoom operation.
Turn off Intelligent Face Detection.
48
49
Playback
Problem
Pictures are
grainy.
Solution
Page
—
—
—
—
Turn silent mode off.
Adjust playback volume.
Hold the camera correctly during recording.
Hold the camera correctly during playback.
Remove protection using the device with
which it was originally applied.
Turn the camera off before opening the
battery-chamber cover.
19
99
90
91
85
6, 98
Troubleshooting
Possible cause
The pictures were taken with a different
make or model of camera.
The pictures were taken with a different
Pictures
Playback zoom make or model of camera.
unavailable.
The pictures were cropped or resized to
the size of t.
The camera is in silent mode.
No sound in
Playback volume is too low.
Audio
voice memo and
The microphone was obstructed.
movie playback.
The speaker is obstructed.
Selected pictures Some of the pictures selected for deletion
Deletion
are not deleted. are protected.
File numbering
The battery-chamber cover was opened
Frame no. is unexpectedly
while the camera was on.
reset.
111
Troubleshooting
Connections
Problem
Prob
em
Poss ble cause
Possible
Monitor is off. The camera is connected to a TV.
The camera is not properly connected.
An A/V cable was connected during movie
playback.
No picture or
Input on the television is set to “TV”.
sound.
TV
The camera is not set to the correct video
standard.
The volume on the television is too low.
The camera is not set to the correct video
No color.
standard.
The computer
does not
The camera is not properly connected.
Computer
recognize the
camera.
The camera is not properly connected.
Pictures can
not be printed. The printer is off.
Only one copy
PictBridge
is printed.
The printer is not PictBridge-compatible.
The date is not
printed.
112
Solution
View pictures on the TV.
Connect the camera correctly.
Connect the camera once movie playback
has ended.
Set input to “VIDEO”.
Match the camera r VIDEO SYSTEM
setting to the TV.
Adjust the volume.
Match the camera r VIDEO SYSTEM
setting to the TV.
Page
52
52
51, 52
—
93
—
93
Connect the camera correctly.
63
Connect the camera correctly.
Turn the printer on.
54
—
—
—
Troubleshooting
Miscellaneous
Prob em
Problem
Nothing happens
when the shutter
button is pressed.
Poss ble cause
Possible
Temporary camera malfunction.
The battery is exhausted.
The camera does not
Temporary camera malfunction.
function as expected.
Solution
Remove and reinsert the battery or
disconnect and reconnect the AC adapter/
DC coupler.
Insert a fresh or fully-charged spare battery.
Remove and reinsert the battery or
disconnect and reconnect the AC adapter/
DC coupler. If the problem persists, contact
your FUJIFILM dealer.
Page
6
6
6
Troubleshooting
113
Warning Messages and Displays
The following warnings are displayed in the monitor:
Warning
O (red)
N (blinks red)
0
Description
The battery is low.
The battery is exhausted.
Slow shutter speed. Picture may be blurred.
R
(displayed in red The camera can not focus.
with red focus frame)
Aperture or shutter
speed shown in red
FOCUS ERROR
TURN OFF THE CAMERA
AND TURN ON AGAIN
NO CARD
The subject is too bright or too dark. The
picture will be over- or under-exposed.
Camera malfunction.
The lens barrel is touched.
No memory card inserted when P COPY is
selected in the playback menu.
The memory card or internal memory is not
formatted or the memory card was formatted
in a computer or other device.
CARD NOT INITIALIZED
The memory card contacts require cleaning.
PROTECTED CARD
BUSY
114
Camera malfunction.
The memory card is locked.
The memory card is incorrectly formatted.
Solution
Insert a fresh or fully-charged spare battery.
Use the flash or mount the camera on a tripod.
• Use focus lock to focus on another subject at the
same distance, then recompose the picture (pg. 32).
• If the subject is poorly lit, try focusing at a distance of
about 2 m (6.6 ft.).
• Use macro mode to focus when taking close-ups.
If the subject is dark, use the flash.
Turn the camera off and then on again, taking care not
to touch the lens. If the message persists, contact a
FUJIFILM dealer.
Insert a memory card.
Format the memory card or internal memory using
the m FORMAT option in the camera setup menu
(pg. 97).
Clean the contacts with a soft, dry cloth. If the
message is repeated, format the memory card (pg. 97).
If the message persists, replace the memory card.
Contact a FUJIFILM dealer.
Unlock the memory card (pg. 8).
Use the camera to format the memory card (pg. 97).
Warning Messages and Displays
Warning
CARD ERROR
Descript on
Description
The memory card is not formatted for use in
the camera.
Format the memory card (pg. 97).
Clean the contacts with a soft, dry cloth. If the
The memory card contacts require cleaning or
message is repeated, format the memory card (pg. 97).
the memory card is damaged.
If the message persists, replace the memory card.
Incompatible memory card.
Use a compatible memory card.
Camera malfunction.
Contact a FUJIFILM dealer.
x MEMORY FULL
The memory card or internal memory is full;
d MEMORY FULL
INTERNAL MEMORY IS FULL pictures can not be recorded or copied.
INSERT A NEW CARD
Not enough memory remaining to record
additional pictures.
The memory card or internal memory is not
formatted.
WRITE ERROR
Delete pictures or insert a memory card with more
free space.
Delete pictures or insert a memory card with more
free space.
Format the memory card or internal memory (pg. 97).
Re-insert the memory card or turn the camera off
and then on again. If the message persists, contact a
FUJIFILM dealer.
The file is corrupt or was not created with the
The file can not be played back.
camera.
Clean the contacts with a soft, dry cloth. If the
The memory card contacts require cleaning. message is repeated, format the memory card (pg. 97).
If the message persists, replace the memory card.
Camera malfunction.
Contact a FUJIFILM dealer.
Troubleshooting
Memory card error or connection error.
READ ERROR
Solution
115
Warning Messages and Displays
Warning
FRAME NO. FULL
Descript on
Description
The camera has run out of frame numbers
(current frame number is 999-9999).
An attempt was made to execute IMAGE
SEARCH over too many pictures.
CANNOT EXECUTE
Red-eye removal cannot be applied to the
A CANNOT EXECUTE selected picture or movie.
An attempt was made to delete, rotate, or add
PROTECTED FRAME
a voice memo to a protected picture.
Voice memo file is corrupt.
5 ERROR
Camera malfunction.
x NO IMAGE
The source device selected in the playback
P COPY menu contains no pictures.
d NO IMAGE
t CAN NOT CROP An attempt was made to crop a t picture.
The picture selected for cropping is damaged
CAN NOT CROP
or was not created with the camera.
An attempt was made to resize a p, q, or
p CANNOT EXECUTE
t picture to the size of p.
An attempt was made to resize a q, or t
q CANNOT EXECUTE
picture to the size of q.
An attempt was made to resize a t picture
t CANNOT EXECUTE
to the size of t.
TOO MANY FRAMES
116
Solution
Format the memory card and select RENEW for the
b FRAME NO. option in the G SET-UP menu.
Take a picture to reset frame numbering to 100-0001,
then return to the b FRAME NO. menu and select
CONTINUOUS.
IMAGE SEARCH cannot process 30,000 pictures or
more.
—
Remove protection before deleting, rotating, or
adding voice memos to pictures.
The voice memo can not be played back.
Contact a FUJIFILM dealer.
Select a different source.
These pictures can not be cropped.
j RESIZE is not available in these cases.
Warning Messages and Displays
Warning
Descript on
Description
The DPOF print order on the current memory
DPOF FILE ERROR
card contains more than 999 images.
CAN NOT SET DPOF
The picture can not be printed using DPOF.
A CAN NOT SET DPOF Movies can not be printed using DPOF.
CAN NOT ROTATE
The picture is protected.
A CAN NOT ROTATE Movies can not be rotated.
PRESS AND HOLD
An attempt was made to choose a flash mode
THE DISP BUTTON TO or adjust the volume with the camera in silent
DEACTIVATE SILENT MODE mode.
A connection error occurred while pictures
COMMUNICATION ERROR were being printed or copied to a computer or
other device.
PRINTER ERROR
CAN NOT BE PRINTED
An attempt was made to print a movie, a
picture not created with the camera, or a
picture in a format not supported by the
printer.
Exit silent mode before choosing a flash mode or
adjusting the volume.
Confirm that the device is turned on and that the USB
cable is connected.
Check printer (see printer manual for details). To
resume printing, turn the printer off and then turn it
back on.
Check printer (see printer manual for details). If
printing does not resume automatically, press MENU/OK
to resume.
Movies and some pictures created with other devices
can not be printed. If the picture was created with the
camera, check the printer manual to confirm that the
printer supports the JFIF-JPEG or Exif-JPEG format. If it
does not, the pictures can not be printed.
Troubleshooting
PRINTER ERROR
RESUME?
Printer out of paper or ink, or other printer
error.
Solution
Copy the pictures to internal memory and create a
new print order.
—
—
Remove protection before rotating pictures (pg. 85).
—
117
Glossary
Digital zoom: Unlike optical zoom, digital zoom does not increase the amount of visible detail. Instead, details
visible using optical zoom are simply enlarged, producing a slightly “grainy” image.
DPOF (Digital Print Order Format): A standard that allows pictures to be printed from “print orders”
stored in internal memory or on a memory card. The information in the order includes the pictures to
be printed and the number of copies of each picture.
EV (Exposure Value): The exposure value is determined by the sensitivity of the image sensor and the amount
of light that enters the camera while the image sensor is exposed. Each time the amount of light doubles, EV
increases by one; each time the amount of light is halved, EV decreases by one. The amount of light entering
the camera can be controlled by adjusting aperture and shutter speed.
HDMI (High-Definition Multimedia Interface): An interface standard for the transmission of images and sound
that adds audio input to the DVI interface used to connect computers to displays.
Motion JPEG: An AVI (Audio Video Interleave) format that stores sound and JPEG images in a single file. Motion
JPEG files can be played in Windows Media Player (requires DirectX 8.0 or later) or QuickTime 3.0 or later.
Smear: A phenomenon specific to CCDs which causes white streaks to appear when very bright light sources,
such as the sun or reflected sunlight, appear in the frame.
White balance: The human brain automatically adapts to changes in the color of light, with the result that objects
that appear white under one light source still appear white when the color of the light source changes. Digital
cameras can mimic this adjustment by processing images according to the color of the light source. This
process is known as “white balance.”
Appendix
118
Internal Memory/Memory Card Capacity
The following table shows the recording time or number of available frames at different image
qualities. All figures are approximate; file size varies with the scene recorded, producing wide
variations in the number of files that can be stored. The number of exposures or length remaining
may not diminish at an even rate.
Still Pictures (FINE) 4 : 3
p
o
Internal memory
(approx. 40 MB)
1 GB
2 GB
4 GB
8 GB
16 GB
Movies
) 1280 *1*2
q
8
13
25
200
410
830
1,680
3,330
330
670
1,340
2,700
5,370
620
1,230
2,480
4,980
9,880
—
! *1
30 sec.
5 min.
10 min.
21 min.
42 min.
83 min.
12 min.
25 min.
50 min.
100 min.
200 min.
*1 Individual movies cannot exceed 2GB in size, regardless of capacity of memory card.
*2 Use a card with a class 4 write speed (4 MB/s) or better when shooting HD movies.
Appendix
119
Specifications
System
Model
Effective pixels
CCD
Storage media
File system
Digital Camera FinePix F80EXR
12 million
1/2 -in. Super CCD EXR
• Internal memory (approx. 40 MB)
• SD/SDHC memory cards (see page 8)
Compliant with Design Rule for Camera File System (DCF), Exif 2.2, and Digital Print Order Format
(DPOF)
File format
• Still pictures: Exif 2.2 JPEG (compressed)
• Movies: AVI-format Motion JPEG
• Audio: WAV
Image size (pixels)
• o 4 : 3: 4,000 × 3,000 • o 3 : 2: 4,000 × 2,664 • o 16 : 9: 4,000 × 2,248
• p 4 : 3: 2,816 × 2,112 • p 3 : 2: 2,816 × 1,864 • p 16 : 9: 2,816 × 1,584
• q 4 : 3: 2,048 × 1,536 • q 3 : 2: 2,048 × 1,360 • q 16 : 9: 1,920 × 1,080
Lens
Fujinon 10 × optical zoom lens, F3.3 (wide angle) – F5.6 (telephoto)
Focal length
f=5.0 mm–50.0 mm (35-mm format equivalent: 27 mm–270 mm)
Digital zoom
• o/p: Approx. 4.0 × (up to 40 × when combined with optical zoom)
• q: Approx. 4.4 × (up to 44 × when combined with optical zoom)
Aperture
F3.3/F9.0 (wide angle), F5.6/F16.0 (telephoto), uses Neutral Density (ND) filter
Focus range (distance from Approx. 45 cm (1.5 ft.)–infinity (wide angle); 2 m (6.6 ft.)–infinity (telephoto)
front of lens)
Macro: approx. 5 cm–2.5 m/2 in.–8.2 ft. (wide angle); 90 cm–2.5 m/3 ft.–8.2 ft. (telephoto)
Quick AF: approx. 1 m (3.3 ft.)–infinity (wide angle); 4 m (13.1 ft.)–infinity (telephoto)
Sensitivity
Standard output sensitivity equivalent to ISO 100, 200, 400, 800, 1600, 3200*1, 6400*2, 12800*2;
AUTO, AUTO (400), AUTO (800), AUTO (1600)
*1 image size p or q, *2 image size q only
Metering
256-segment through-the-lens (TTL) metering; MULTI, SPOT, AVERAGE
Exposure control
Program and 2-stop aperture-priority autoexposure; manual exposure
Exposure compensation
–2 EV – +2 EV in increments of 1/3 EV
120
Specifications
System
Scene modes
A (NATURAL AND FLASH LIGHTING), B (NATURAL LIGHT), G (PRO FOCUS),
F (PRO LOW-LIGHT), U (PORTRAIT), V (PORTRAIT ENHANCER), Y (DOG), T (CAT),
K (LANDSCAPE), L (SPORT), D (NIGHT), U (NIGHT (TRIPOD)), W (FIREWORKS), E (SUNSET),
F (SNOW), G (BEACH), X (UNDERWATER), I (PARTY), O (FLOWER), P (TEXT)
Picture stabilization
Optical stabilization (CCD shift)
Intelligent Face Detection Available
Shutter speed (combined • D: 1/4 s–1/1,000 s
mechanical and electronic • U: 3 s–1/1,000 s
shutter)
• W: 4 s–1/2 s
• Manual selection: 8 s–1/2,000 s
• Other modes: 1/4 s–1/2,000 s
Continuous
• m: up to 1.6 fps; max. 5 frames
• o: up to 1.6 fps; last 5 frames recorded
• S*: up to 4.2 fps; max. 23 frames
• R*: up to 4.2 fps; last 23 frames recorded
* image size q only
Focus
• Mode: Center AF, Multi AF, Continuous AF, Tracking AF
• Autofocus system: Contrast-detect TTL AF
White balance
Automatic scene detection; seven manual preset modes for direct sunlight, shade, daylight
fluorescent, warm white fluorescent, cool white fluorescent, incandescent, and underwater
lighting; custom white balance
Self-timer
Off, 2 sec., 10 sec.
Appendix
121
Specifications
System
Flash
Flash modes
Monitor
Frame coverage
Movies
Shooting options
Playback options
Other options
Input/output terminals
A/V OUT (audio/video output)
Digital input/output
HDMI output
122
Auto flash; effective range when sensitivity is set to ISO 800 is approx. 30 cm–4.2 m/1 ft.–13.8 ft. (wide
angle), 90 cm–2.4 m/3 ft.–7.9 ft. (telephoto)
Auto, forced flash, off, slow synchro (red-eye removal off); auto with red-eye removal, forced flash with
red-eye removal, off, slow synchro with red-eye removal (red-eye removal on)
3.0-in., 230k-dot color LCD monitor
Approx. 100%
Frame size 1,280 × 720 (24 fps) or 640 × 480 (30 fps); monaural sound; AF mode; white balance;
Intelligent Face Detection
EXR mode (EXR AUTO, RESOLUTION PRIORITY, HIGH ISO & LOW NOISE, D-RANGE PRIORITY), FACE
RECOGNITION, Dynamic range, Intelligent Face Detection with red-eye removal, PRO LOW-LIGHT,
PRO FOCUS, Dog/Cat detection, power management, framing guideline, frame number memory,
and film simulation
Intelligent Face Detection, red-eye removal, micro thumbnail, multi-frame playback, image search,
crop, resize, slide show, image rotation, and voice memo
PictBridge, Exif Print, language selection (Japanese / English / French / German / Spanish / Italian /
Simplified Chinese / Korean / Dutch / Portuguese / Russian / Thai / Turkish / Traditional Chinese /
Czech / Hungarian / Polish / Swedish / Slovak / Danish / Norwegian / Finnish / Arabic / Farsi /
Greek / Lithuanian / Ukraine), time difference, silent mode
8-pin multi-connector for NTSC or PAL output with monaural sound
USB 2.0 High Speed; shares A/V OUT connector
HDMI Micro Connector (Type D)
Specifications
Power supply/other
Power supply
Guide to the number of
available frames for battery
operation
Camera dimensions
(W × H × D)
Camera weight
Shooting weight
Operating conditions
NP-50 rechargeable battery; optional AC power adapter AC-5VX and DC coupler CP-50
Battery Type NP-50 Number of frames Approx. 230 frames (AUTO mode)
According to the CIPA (Camera & Imaging Products Association) standard procedure for measuring
digital still camera battery consumption (extract):
When using a battery, use the battery supplied with the camera. The storage media should be SD
memory card.
Note that the number of shots that can be taken with a fully-charged battery varies with
temperature and shooting conditions.
99.3 mm × 58.9 mm × 28.4 (22.9*) mm/3.9 in. × 2.3 in. × 1.1 (0.9*) in.
* excluding projecting parts, measured at the thinnest part
Approx. 183 g/6.5 oz., excluding batteries, accessories, and memory cards
Approx. 203 g/7.2 oz., including batteries and memory card
Temperature: 0 °C to +40 °C (+32 °F to +104 °F)
80% humidity or less (no condensation)
Appendix
123
Specifications
NP-50 rechargeable battery
Nominal voltage
Nominal capacity
Operating temperature
Dimensions (W × H × D)
Weight
DC 3.6 V
1000 mAh
0 °C – +40 °C/+32 °F – +104 °F
35.4 mm × 40.0 mm × 6.6 mm/1.4 in. × 1.6 in. × 0.3 in.
Approx. 18 g/0.6 oz.
BC-45W battery charger
Rated input
Input capacity
Rated output
Supported batteries
Charging time
Dimensions (W × H × D)
Weight
Operating temperature
100 V–240 V AC, 50/60 Hz
8.0 VA (100 V) 12 VA (240 V)
4.2 V DC, 550 mA
NP-50 rechargeable batteries
Approx. 150 minutes (+20 °C/+68 °F)
91 mm × 62 mm × 23 mm/3.6 in. × 2.4 in. × 0.9 in.
Approx. 67 g/2.4 oz., excluding battery
0 °C – +40 °C/+32 °F – +104 °F
The weight and dimensions vary with the country or region of sale.
124
Specifications
Color Television Systems
NTSC (National Television System Committee) is a color television telecasting specification adopted mainly in
the U.S.A., Canada, and Japan. PAL (Phase Alternation by Line) is a color television system adopted mainly in
European countries and China.
Notices
• Specifications subject to change without notice. FUJIFILM shall not be held liable for damages resulting from
errors in this manual.
• Although the monitor is manufactured using advanced high-precision technology, small bright points and
anomalous colors (particularly in the vicinity of text) may appear. This is normal for this type of monitor and
does not indicate a malfunction; images recorded with the camera are unaffected.
• Digital cameras may malfunction when exposed to strong radio interference (e.g., electric fields, static
electricity, or line noise).
• Due to the type of lens used, some distortion may occur at the periphery of images. This is normal.
Appendix
125
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN
http://www.fujifilm.com/
Download PDF

advertising