Operating instructions | Frigidaire FASG7021NW Washer/Dryer User Manual

All about the
Use & Care
of your
Wall Oven
TA B L E O F C O N T E N T S
Setting Oven Controls.............................................8
Important Safety Instructions..................................3
Care & Cleaning...................................................10
Features at a Glance...............................................6
Before You Call ...................................................14
Before Setting Oven Controls..................................7
Major Appliance Warranty.....................................16
www.frigidaire.com USA 1-800-944-9044
www.frigidaire.ca Canada 1-800-265-8352
318200965 (October 2009) Rev. A
Welcome & Congratulations....................................2
Welcome & Congratulations
Product Registration
Register Your Product
The PRODUCT
REGISTRATION
CARD should be filled in
completely, signed and
returned to Electrolux
Major Appliances.
Serial Plate Location
Congratulations on your purchase of a new appliance!
At Electrolux Major Appliances, we are very proud of
our product and are completely committed to providing
you with the best service possible. Your satisfaction is our
number one priority.
We know you’ll enjoy your new appliance and Thank You
for choosing our product. We hope you consider us for
future purchases.
Please CAREFULLY read and save these
instructions
This Use & Care Manual contains general operating
instructions for your appliance and feature information
for several models. Your product may not have
all the described features. The graphics shown are
representative. The graphics on your appliance may not
look exactly like those shown. These instructions are not
meant to cover every possible condition and situation
that may occur. Common sense and caution must be
practiced when installing, operating and maintaining any
appliance.
 NOTE
Please attach sales receipt here for future reference.
Please record your model and serial numbers
below for future reference.
Model Number:
Serial Number:
Purchase Date:
© 2009 Electrolux Canada Corp.
All rights reserved
Printed in United States
2
WARNING
If the information in this manual is not followed
exactly, a fire or explosion may result causing
property damage, personal injury or death.
FOR YOUR SAFETY:
— Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
— WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire
department.
— Installation and service must be performed by a
qualified installer, servicer or the gas supplier.
Important Safety Instructions
Read all instructions before using this appliance.
Save these instructions for future reference.
Definitions
This is the safety alert symbol. It is used to alert you to
potential personal injury hazards. Obey all safety messages
that follow this symbol to avoid possible injury or death.
WARNING
This symbol will help alert you to situations that may
cause serious bodily harm, death or property damage.
CAUTION
This symbol will help alert you to situations that
may cause bodily injury or property damage.
IMPORTANT
IMPORTANT indicates installation, operation or maintenance
information which is important but not hazard-related.
•Remove all tape and packaging wrap before using
the appliance. Destroy the carton and plastic
bags after unpacking the appliance. Never allow
children to play with packaging material. Do not remove
the wiring label and other literature attached to the
appliance. Do not remove model/serial number plate.
•Proper Installation. Be sure your appliance is
properly installed and grounded by a qualified
technician in accordance with the National Fuel
Gas Code ANSI Z223.1/NFPA 54 latest edition,
and National Electrical Code ANSI/NFPA No.70latest edition and local code requirements. Install
only per installation instructions provided in the literature
package for this appliance.
Ask your dealer to recommend a qualified technician and
an authorized repair service. Know how to disconnect the
electrical power to the appliance at the circuit breaker or
fuse box in case of an emergency.
CAUTION
Electronic controllers can be damaged by cold
temperatures. When you use your appliance for
the first time, or if it has not been used for a long
period of time, make sure that it has been exposed
to a temperature above 0°C/32°F for at least 3
hours before connecting it to the power supply.
•User Servicing. Do not repair or replace any part
of the appliance unless specifically recommended
in the manuals. All other servicing should be done only
by a qualified technician to reduce the risk of personal
injury and damage to the appliance.
•Never modify or alter the construction of an
appliance such as removal of panels, wire covers
or any other permanent part of the appliance.
WARNING
• All appliance can tip.
•Injury to persons could result.
•Install anti-tip bracket packed with
your appliance.
•See Installation Instructions.
To reduce the risk of tipping, the
appliance must be secured by properly
installed anti-tip screws provided
with the unit. Refer to the Installation
Instructions for proper anti-tip bracket
installation.
•Storage in or on Appliance. Flammable materials
should not be stored in the oven, or in the broiler
drawer (if equipped). This includes paper, plastic and
cloth items, such as cookbooks, plasticware and towels, as
well as flammable liquids. Do not store explosives, such as
aerosol cans, in or near the appliance. Flammable materials
may explode and result in fire or property damage.
•Remove the oven door from any unused appliance
if it is to be stored or discarded.
WARNING
Stepping, leaning, sitting or pulling down on the
door of this appliance can result in serious injuries
and may also cause damage to the appliance. Do not
allow children to climb or play around the appliance.
WARNING
Do not use the oven for storage.
CAUTION
Do not store items of interest to children in the
cabinets above the appliance. Children climbing on
the cooktop to reach items could be seriously injured.
•Do not leave children alone. Children should not
be left alone or unattended in the area where an
appliance is in use. They should never be allowed to
sit or stand on any part of the appliance.
•DO NOT TOUCH INTERIOR OVEN BURNER OR
INTERIOR SURFACES OF THE WALL OVEN UNTIL
THEY HAVE COOLED. The oven heating burners may
be hot even though the flames are not visible. Areas near
the burners may become hot enough to cause burns.
During and after use, do not touch, or let clothing or
other flammable materials touch these areas until they
have had sufficient time to cool. Among these areas
are the oven vent openings, the surfaces near these
openings, oven door window and broiler drawer.
3
Important Safety Instructions
•Wear Proper Apparel. Loose-fitting or hanging
garments should never be worn while using the
appliance. Do not let clothing or other flammable
materials contact hot surfaces.
WARNING
Never use this appliance as a space heater to heat
or warm the room. Doing so may result in carbon
monoxide poisoning and overheating of the oven.
•Do Not Use Water or Flour on Grease Fires.
Smother the fire with a pan lid, or use baking
soda, a dry chemical or foam-type extinguisher.
•When heating fat or grease, watch it closely. Fat
or grease may catch fire if allowed to become too hot.
•Use Only Dry Pot Holders. Moist or damp pot
holders on hot surfaces may result in burns from
steam. Do not let the pot holders touch hot surface
units. Do not use a towel or other bulky cloth instead of
a pot holder.
•Do Not Heat Unopened Food Containers. Buildup
of pressure may cause the container to burst and
result in injury.
IMPORTANT
Do not attempt to operate the appliance during
a power failure. If the power fails, always turn
off the unit. If the unit is not turned off and the power
resumes, the appliance will not operate and an error
message will be displayed. Food left unattended could
catch fire or spoil.
IMPORTANT SAFETY INSTRUCTIONS FOR
USING YOUR OVEN
•Use Care When Opening an Oven Door—Stand to
the side of the appliance when opening the door of a hot
oven. Let hot air or steam escape before you remove or
replace food in the oven.
•Keep Oven Vent Ducts Unobstructed. The wall oven
is vented at the center trim under the control panel.
Touching the surfaces in this area when the oven is
operating may cause severe burns. Also, do not place
plastic or heat-sensitive items near the oven vent. These
items could melt or ignite.
•Placement of Oven Racks. Always place oven racks in
desired location while oven is cool. Remove all utensils
from the rack before removing rack. If rack must be
moved while oven is hot, use extreme caution. Use pot
holders and grasp the rack with both hands to reposition.
Do not let pot holders contact the oven burner flame or
interior of the oven or broiler drawer. Remove all utensils
from the rack before removing the rack.
4
•Do not use a broiler pan without its insert. Broiler
pan and grid allow dripping fat to drain and be kept away
from the high heat of the broiler.
WARNING
Never cover any slots, holes or passages in
the oven bottom or cover an entire rack with
materials such as aluminum foil. Doing so blocks air
flow through the oven and may cause carbon monoxide
poisoning. Aluminum foil linings may trap heat, causing
a fire hazard.
•Do not cover the broiler grid or oven bottom with
aluminum foil. Exposed fat and grease could ignite.
•Do not touch a hot oven light bulb with a damp
cloth. Doing so could cause the bulb to break.
Disconnect the appliance or shut off the power to the
appliance before removing and replacing the bulb.
IMPORTANT SAFETY INSTRUCTIONS FOR
CLEANING YOUR OVEN
•Clean the appliance regularly to keep all parts
free of grease that could catch fire. Exhaust fan
ventilation hoods and grease filters should be kept clean.
Do not allow grease to accumulate. Greasy deposits in
the fan could catch fire. Refer to the hood manufacturer’s
instructions for cleaning.
•Cleaners/Aerosols—Always follow the manufacturer’s
recommended directions for use. Be aware that excess
residue from cleaners and aerosols may ignite causing
damage and/or injury.
IMPORTANT SAFETY NOTICE
The California Safe Drinking Water and Toxic
Enforcement Act requires the Governor of California
to publish a list of substances known to the state to
cause cancer, birth defects or other reproductive harm,
and requires businesses to warn customers of potential
exposure to such substances.
Important Safety Instructions
Grounding instructions
Oven Ignition
For personal safety, the cooktop must be properly
grounded. For maximum safety, the power cord must be
plugged into an electrical outlet that is correctly polarized
and properly grounded.
DO NOT operate the cooktop using a 2-prong adapter or
an extension cord. If a 2-prong wall receptacle is the only
available outlet, it is the personal responsibility of the
consumer to have it replaced with a properly grounded
3-prong wall receptacle installed by a qualified electrician.
See the installation instructions packaged
with this cooktop for complete installation and grounding
instructions.
When you turn the oven on, the glow bar igniter begins to
heat. When the lighter is hot enough, in less than 1 minute,
the gas flows into the burner and is ignited.
WARNING
This appliance is equipped with a 3-prong grounding
plug for your protection against shock hazard and
should be plugged directly into a properly grounded
receptacle. DO NOT cut or remove the grounding
prong from this plug.
Grounding
type wall
receptacle
Do not, under any
circumstances,
cut, remove,
or bypass the
grounding prong.
Power supply cord with
3-prong grounding plug
WARNING
Avoid fire hazard or electrical shock. DO NOT use an
adapter plug, an extension cord, or remove grounding
prong from electrical power cord. Failure to follow this
warning can cause serious injury, fire or death.
The igniter glows bright orange when hot. It cycles on and
off with the thermostat and will glow whenever the burner
is on.
WARNING
Do not attempt to light the oven burners during a power
failure. The oven burner valves will not open up and will
prevent the gas from flowing through the burner valves
to the burners. In the event of a power failure, turn the
Temperature Control knob to OFF. When power resumes,
turn the Temperature Control knob back to desired
temperature.
Conversion to liquefied petroleum gas
(or L.P. gas)
This natural gas range is designed to allow for conversion
to Liquefied Petroleum (L.P.) Gas.
If L.P. conversion is needed, contact the service center
for assistance. The L.P. Conversion Kit is provided with
this cooktop and is located in the literature envelope.
Before installing the kit be sure to follow the L.P.
Installation Instructions carefully.
WARNING
Personal injury or death from electrical shock may
occur if the range is not installed by a qualified installer
or electrician.
CAUTION
Any additions, changes or conversions required in order
for this appliance to satisfactorily meet the application
needs must be made by an authorized Service Center.
5
FEATURES AT A GLANCE
Your Gas Wall-Oven
Features:
1. Electronic oven control with
kitchen timer.
2. Oven light switch.
3. Oven vent.
4. Manual clean oven interior.
5. Oven interior light with removable
cover.
6. Adjustable interior oven rack(s).
7. Large 1-piece oven door handle.
8. Oven door with window.
9. Broiler Oven Cavity.
10. Bottom trim.
 NOTE
The features shown for your appliance may
vary according to model type & color.
6
BEFORE SETTING OVEN CONTROLS
Oven Vent Location
Arranging Oven Racks
The oven is vented at the upper trim. When the oven is
on, warm air is released through the vent. This venting is
necessary for proper air circulation in the oven and good
baking results. DO NOT block the vents. Doing so may
cause baking failures, fire or damage to the wall oven.
Always arrange oven racks when THE oven is
cool (Prior to operating the oven). Always use
oven mitts when using the oven.
To remove an oven rack, pull the rack forward until it
stops. Lift up front of rack and slide out.
To replace an oven rack, fit the rack onto the guides
on the oven walls. Tilt the front of the rack upward and
slide the rack back into place.
Air Circulation in the Oven
If using 1 rack, place in center of oven. If using multiple
racks, stagger cookware as shown.
For best air circulation and baking results allow 2-4"
(5-10cm) around the cookware for proper air circulation
and be sure pans and cookware do not touch each other,
the oven door, sides or back of the oven cavity. The hot
air must circulate around the pans and cookware in the
oven for even heat to reach around the food.
7
Setting OVEN controls
Control pad features
READ THE INSTRUCTIONS CAREFULLY BEFORE USING THE OVEN. For satisfactory use of your oven, become
familiar with the various features and functions of the oven as described below. Detailed instructions for each
feature and function follow later in this Use & Care Guide.
1. Bake pad—Use to select the bake cooking feature.
2. Broil pad—Use to select the broil cooking feature.
3. Timer on-off pad—Use to set or cancel the Timer.
The Timer does not start or stop cooking.
4. Clock pad—Use to set the time of day.
5. Clear off pad—Use to cancel any oven feature
previously entered except the time of day and minute
timer.
6. Down arrow pad—Used along with the function pads
to select oven temperature, time of day and minute timer.
7. Up arrow pad—Used along with the function pads to
select oven temperature, time of day and minute timer.
To Set the Clock
To Set the Minute Timer
When the appliance is first plugged in, or when the
power supply to the range has been interrupted, the
display will flash "12:00".
1. Press CLOCK pad.
2. Within 4 seconds, press and hold the UP or DOWN
ARROW pad until the correct time of day appears in
the display.
1. Press TIMER ON/OFF pad.
2. Press the UP ARROW pad to increase the time
in one minute increments. Press and hold the UP
ARROW pad to increase the time faster. The timer
can be set for any amount of time from 1 minute to
11 hours and 59 minutes.
Note: If you press the DOWN ARROW pad first,
the timer will advance to 11 hours and 59 minutes.
3. The display shows the timer count down in minutes
until one minute remains. Then the display will count
down in seconds.
4. When the set time has run out, the timer will sound a
3 seconds beep. 0:00 will appear in the display until
TIMER ON/OFF pad is pressed.
To Change the Temperature Display Mode
The electronic oven control temperature display mode
was factory preset to display (Fahrenheit) °F oven
temperatures. Note: Oven cooking temperatures may be
set from 170°F to 500°F (76°C to 260°C).
To change the Temperature Display Mode to °C
(Celsius) or from °C to °F (do not use Bake or Broil
while changing the Temperature Display Mode):
1. Press & hold the BROIL pad for 7 seconds until F
or C appears in the display. Note: At this time the
display will show the current Temperature Display
Mode whether set for F or C.
2. Within 4 seconds, press the UP or DOWN ARROW
pad once to toggle between the °F (Fahrenheit) and
°C (Celsius).
3. To accept the change, wait 5 more seconds until the
oven control beeps once. To complete the change
skip step 4 below, OR;
4. If at any time during the process of changing the
Temperature Display Mode (F or C) you decide the
change is not desired, press the CLEAR OFF pad before
the oven control beeps once to cancel the process.
5. The display will then return to the time of day with
any temperature display mode change you may have
requested.
8
Note: While the minute timer is counting down, the
“:” will flash. The minute timer does not start or stop
cooking. It serves as an extra timer in the kitchen that
will beep when the set time has run out. The minute
timer can be used alone or during any of the other oven
functions. When the minute timer is in use with any other
function, the minute timer will be shown in the display. To
view other functions, press the pad for that function.
To Change the Minute Timer while it is in use:
While the timer is active and shows in the display, press
and hold the UP or DOWN ARROW pad to increase or
decrease the time.
To Cancel the Minute Timer before the set time
has run out: Press TIMER ON/OFF.
Setting OVEN controls
To Set or Change the Temperature for
Baking
The oven can be programmed to bake at any
temperature from 170°F to 500°F (76°C to 260°C).
To Set the Controls for Baking:
1. Press BAKE pad. "— — —°" appears in the display.
2. Within 5 seconds, press the UP or DOWN ARROW
pad. The display will show "350°F." By pressing
and holding the UP or DOWN ARROW pad, the
temperature can then be adjusted in 5°F increments.
3. When the UP or DOWN ARROW pad is released,
the oven will begin heating to the selected
temperature. When the displayed temperature
reaches the desired baking temperature, the control
will beep once (1 time).
4. To cancel the baking function, press CLEAR OFF
pad.
To Change the Oven Temperature after Baking has
Started:
1. Press BAKE pad and make sure the bake
temperature is displayed.
2. Press the UP or DOWN ARROW pad to increase or
decrease the set temperature.
To Broil
1. Arrange oven rack while oven is still cool.
2. Press BROIL pad.
3. Press and hold the UP or DOWN ARROW pad until
the desired broil setting level appears in the display.
Press the UP ARROW pad for HI broil or the DOWN
ARROW pad for LO broil. Most foods can be broiled
at the HI broil setting. Select the LO broil setting to
avoid excess browning or drying of foods that should
be broiled to the well-done stage.
4. Place the insert on the broiler pan, then place the
food on the insert. DO NOT use the broiler pan
without the insert or cover the insert with aluminum
foil. The exposed grease could ignite.
5. Place the pan on the oven rack in the lower oven.
Close the oven door when broiling.
6. Broil on one side until food is browned; turn and cook
on the second side. Note: Always pull the rack out to
the stop position before turning or removing food.
7. When broiling is finished, press CLEAR OFF pad.
CAUTION
Should an oven fire occur, close the oven door
and turn off the oven. If the fire continues, use a
fire extinguisher. DO NOT put water or flour on
the fire. Flour may be explosive.
Adjusting Your Oven Temperature
Your new oven has been factory calibrated and tested
to ensure an accurate baking temperature. For the first
few uses, follow your recipe times and temperature
recommendations carefully. If you feel your oven is too
hot or too cool from your baking experience, the oven
temperature may be adjusted to your liking.
 NOTE
DO NOT adjust your oven temperature based on oven
thermometers, such as those found in grocery stores,
they may not be accurate.
To Adjust the Oven Temperature (do not use Bake
or Broil while adjusting the oven temperature):
Note: Your oven control was factory set in the
(Fahrenheit) °F Temperature Display Mode. To change for
(Celsius) °C, see appropriate section.
1. Press & hold the BAKE key pad and release after the
display shows the factory temperature setting of 00.
Note: If the oven temperature has been previously
adjusted from the factory setting, the current
temperature adjusted value will appear in the display
instead.
2. You may increase the oven temperature in 5°F (1°C)
increments with each press of the UP ARROW pad
to a maximum oven adjustment of +35°F (+18°C).
You may also adjust the oven temperature downward
in 5°F (1°C) increments with each press of the
DOWN ARROW pad (total range of -35°F to +35°F
(-18°C to +18°C).
3. If you do not want to keep the display adjustment,
press the CLEAR OFF pad before the oven control
beeps. This will cancel the temperature adjustment
procedure. To start this procedure over again begin
with step 1 above OR;
4. If you want to keep the adjustment, wait until the
oven control beeps once.
5. The oven temperature adjustment has be accepted
by the oven control and the display will return to the
time of day.
Failure Modes
All failure modes give a visual and audible alarm. When
display shows F10 (temperature runaway), F30-F31 (oven
sensor circuit fault) or any other F error codes, the electronic oven control has detected a fault condition. Note
that code and push the CLEAR OFF pad to clean the display and stop the beeping. Reprogram the oven. If fault
recurs, push CLEAR OFF pad, disconnect the appliance to
prevent damage and contact an authorized servicer.
9
CARE & CLEANING
Cleaning Various Parts of Your Range
Before cleaning any part of the range, be sure all controls are turned OFF and the range is COOL. Remove spillovers and
heavy soiling as soon as possible. Regular cleaning will reduce the number of major cleaning later.
Surface type
Recommendation
• Aluminum & Vinyl
Use hot, soapy water and a cloth. Dry with a clean cloth.
• Painted and plastic control
knobs
• Painted body parts
• Painted decorative trims
Using a soft cloth, clean with mild dish detergent and water or a 50/50 solution of
vinegar and water. Follow by rinsing the area with clean water; dry and polish with
a soft cloth. Glass cleaners may be used if sprayed on a soft cloth first. DO NOT
spray liquids directly on the control pad and display area. Do not use large amounts
of water on the control panel - excess water on the control area may cause damage
to the appliance. Do not use other liquid cleaners, abrasive cleaners, scouring pads,
or paper towels - they will damage the finish. To remove control knobs, turn to the
OFF position; grasp firmly and pull straight off the shaft. To replace knobs after
cleaning, line up the flat sides of both the knob and the shaft; then push the knob
into place.
• Stainless Steel (some
models) Oven Door &
Drawer Front Panel and
Decorative Trim
Clean stainless steel with hot, soapy water and a dishcloth. Rinse with clean
water and a cloth. Do not use cleaners with high concentrations of chlorides or
chlorines. Do not use harsh scrubbing cleaners. Only use kitchen cleaners that
are especially made for cleaning stainless steel. Always be sure to rinse the
cleaners from the surface as bluish stains may occur during heating that cannot
be removed.
• Porcelain enamel broiler
pan and insert (available by
mail order)
• Door liner & body parts
Gentle scouring with a soapy scouring pad will remove most spots. Rinse with a
1:1 solution of clear water and ammonia. If necessary, cover difficult spots with an
ammonia-soaked paper towel for 30 to 40 minutes. Rinse with clean water and a
damp cloth, and then scrub with a soap-filled scouring pad. Rinse and wipe dry with
a clean cloth. Remove all cleaners or the porcelain may become damaged during
future heating. DO NOT use spray oven cleaners on the cooktop.
• Oven racks
Oven racks must be removed from oven cavity. Clean by using a mild, abrasive
cleaner following manufacturer’s instructions. Rinse with clean water and dry.
• Oven door
Use soap & water to thoroughly clean the top, sides and front of the oven door. Rinse
well. You may use a glass cleaner on the outside glass of the door. Do not immerse
the door in water. Do not spray or allow water or the glass cleaner to enter
the door vents. Do not use oven cleaners, cleaning powders or any harsh abrasive
cleaning materials on the outside of the oven door.
Do not clean the oven door gasket. On self-clean models, the oven door gasket is
made of a woven material which is essential for a good seal. Care should be taken
not to rub, damage or remove this gasket.
10
Care & Cleaning
Non Self-Clean Oven
Porcelain has a smooth finish and is a type of glass fused
to metal. Oven cleaners can be used on all interior oven
surfaces.
Remove spillovers and heavy soiling as soon as
possible. Regular cleaning will reduce the number
of major cleaning later.
Adhere to the following cleaning precautions:
•Allow the oven to cool before cleaning.
•Wear rubber gloves when cleaning the appliance
manually.
General Cleaning
Remove soils using hot, soapy water. Do not allow food
spills with a high sugar or acid content (such as milk,
tomatoes, saukerkraut, fruit juices or pie filling) to remain
on the surface as they may cause a dull spot even after
cleaning.
To Remove Heavy Soil:
1. Allow a dish of ammonia to sit in the oven overnight
or for several hours with the oven door closed. Clean
softened spots using hot, soapy water. Rinse well with
water and a clean cloth.
2. If soil remains, use a soap-filled scouring pad or a
nonabrasive cleaner. If necessary, use an oven cleaner
following manufacturer's instructions. DO NOT mix
ammonia with other cleaners.
3. Clean any soil from the oven frame, the door liner
outside the oven door gasket and the small area at the
front center of the oven bottom. Clean with hot, soapy
water. Rinse well using clean water and a cloth.
CAUTION
• Ammonia must be rinsed before operating the oven.
Provide adequate ventilation.
• DO NOT line the oven walls, bottom, racks or any other
part of the appliance with aluminum foil. Doing so will
destroy heat distribution, produce poor baking results and
cause permanent damage to the oven interior (aluminum
foil will melt to the interior surface of the oven).
Cleaning the Oven Bottom
The oven bottom in non self-clean oven models can be
removed for cleaning. See "To Remove and Replace Oven
Bottom" under General Cleaning.
Clean using hot, soapy water, a mild abrasive cleanser,
a soap-filled abrasive pad or oven cleaner following
manufacturer's instructions.
Adhere to the following precautions when using
oven cleaners:
1. DO NOT spray on the electrical controls or switches
because it could cause a short circuit and result in
sparking or fire.
2. DO NOT allow a film from the cleaner to build up on
the temperature sensing bulb; it could cause the oven
to heat improperly. (The bulb is located in the rear
of the oven.) Carefully wipe the bulb clean after each
oven cleaning, being careful not to move the bulb. A
change in its position could affect how the oven bakes.
Avoid bending the bulb and capillary tube.
3. DO NOT spray any cleaner on the oven door trim or
gasket, handles or any exterior surfaces of the range,
wood or painted surfaces. The cleaner can damage
these surfaces.
11
CARE & CLEANING
To Remove and Replace Oven Bottom
To Remove the Oven Bottom (upper oven):
1.Remove racks, broiler pan (some models) and wire
guides.
2.Using the finger openings on each side of the oven
bottom, pull out and lift up the oven bottom.
To Replace the Oven Bottom (upper oven):
1.Grasp the oven bottom and position the front tabs in
place in the slots at the rear of the oven bottom.
2.Lower the front of the oven bottom and slide into place.
3.Replace wire guides.
caution
If oven bottom fits too tightly, place your hand under
the bottom through the lower cavity and push up on
each side of the front end.
Lower Oven
Changing oven light
CAUTION
Be sure the oven is unplugged and all parts are COOL
before replacing the oven light. Wear a leather-faced glove
for protection against possible broken glass.
Use the rocker switch located on the control panel to turn
the oven light on or OFF. On some models, the oven light
automatically will turn automatically on when the oven
door is opened.
Upper Oven
Use the finger openings along the outside edges of the
oven bottom to remove the oven bottom.
To Remove the Oven Bottom (lower oven):
1.Remove utensils, racks and wire guides.
2.Pull out and lift up the oven bottom.
To Change the Oven Light
1. Turn electrical power off at the main source or unplug
the oven.
2. Replace bulb with a new 40 watt appliance bulb.
3. Turn power back on again at the main source (or plug
the oven back in).
4. The clock will then need to be reset.
To Replace the Oven Bottom (lower oven):
1.Lower the front of the oven bottom and slide into
place.
2.Replace wire guides.
Double Oven Models
Upper Oven Only
12
Care & Cleaning
Care and cleaning of stainless steel
Some models are equipped with stainless steel exterior
parts. Special care and cleaning are required for
maintaining the appearance of stainless parts. Refer to
the General Care & Cleaning table for detailed cleaning
instructions.
Removing and replacing the lift-off oven
door
CAUTION
Around
Oven door
Hinge
Figure 3
Figure 4
Special door care instructions - Most oven
The door is heavy. For safe, temporary storage, lay the
door flat with the inside of the door facing down.
To Remove Oven Door:
1. Open oven door completely (horizontal with floor See Figure 1).
2. Pull the door hinge locks on both left and right
door hinges down from the oven frame completely
towards the oven door (See Figure 2). A tool such as
a small flat-blade screwdriver may be required.
3. Firmly grasp both sides of oven door along the door
sides (Do not use the oven door handle - See Figure 3).
4. Close the door to the broil stop position (the oven
door will stop into this position just before fully
closing).
5. With the oven door in the broil stop position, lift the
oven door hinge arms over the roller pins located on
each side of the oven frame (See Figure 4).
doors contain glass that can break.
Read the following recommendations:
1. Do not close the oven door until all the oven racks are
fully in place.
2. Do not hit the glass with pots, pans, or any other object.
3. Scratching, hitting, jarring or stressing the glass may
weaken its structure causing an increased risk of
breakage at a later time.
To Replace Oven Door:
1. Firmly grasp both sides of oven door along the door
sides (Do not use the oven door handle - See Figure 3).
2. Holding the oven door at the same angle as the
removal position, seat the hook of the hinge arm over
the roller pins located on each side of the oven door
frame (See Figure 4). The hook of the hinge arms
must be fully seated onto the roller pins.
3. Fully open the oven door (horizontal with floor - See
Figure 1).
4. Push the door hinge locks up towards and into the
oven frame on both left and right oven door hinges
(See Figure 2) to the locked position.
5. Close the oven door.
Door Hinge locations
with oven door fully open
Figure 1
Figure 2
13
Before you call - Solutions to Common Problems
Oven Baking
For best cooking results, heat the oven before baking cookies, breads, cakes, pies or pastries, etc. There is no need to
preheat the oven for roasting meat or baking casseroles.
The cooking times and temperatures needed to bake a product may vary slightly from your previously owned
appliance.
Baking Problems and Solutions Chart
Baking
Problems
Cookies and
biscuits burn on
the bottom.
Causes
Corrections
• Cookies and biscuits put into
the oven before the preheating
time is completed.
• Oven rack overcrowded.
• Allow oven to preheat to the selected temperature
before placing food in oven.
• Dark pan absorbs heat too fast.
• Choose pan sizes that will permit 5.1cm to 10.2cm
(2” to 4”) of air space on all sides when placed in
the oven.
• Use a medium-weight aluminum baking sheet.
Cakes too dark on
top or bottom.
• Cakes put into the oven before
preheating time is completed.
• Rack position too high or low.
• Oven too hot.
• Allow oven to preheat to the selected temperature
before placing food in the oven.
• Use proper rack position for baking needs.
• Set oven temperature 25°F/12°C lower than
recommended.
Cakes not done in
the center.
• Oven too hot.
• Set oven temperature 25°F/12°C lower than
recommended.
• Use pan size suggested in recipe.
• Use proper rack position and place pan so there is
5.1cm to 10.2cm (2” to 4”) of space on all sides of
pan.
Cakes not level.
• Incorrect pan size.
• Pan not centered in oven.
• Range not level.
• Pan too close to oven wall or
rack overcrowded.
• Pan warped.
Foods not done
when cooking time
is up.
• Oven too cool.
• Oven overcrowded.
• Oven door opened too
frequently.
14
• Place a marked glass measuring cup filled with
water on the center of the oven rack. If the water
level is uneven, refer to the installation instructions
for leveling the range.
• Be sure to allow 5.1cm to 10.2cm (2” to 4”) of
clearance on all sides of each pan in the oven.
• Do not use pans that are dented or warped.
• Set oven temperature 25°F/12°C higher than
suggested and bake for the recommended time.
• Be sure to remove all pans from the oven except
the ones to be used for baking.
• Open oven door only after shortest recommended
baking time.
Before you call - Solutions to Common Problems
IMPORTANT
Before you call for service, review this list. It may save you time and expense. The list includes common
occurrences that are not the result of defective workmanship or materials in this appliance.
OCCURRENCE
POSSIBLE CAUSE/SOLUTION
Oven Control Beeps
and Displays an “F”
Error Code
Electronic control has detected a fault condition. Push CANCEL pad to clear the display and stop the
display from beeping. Reprogram the oven. If a fault reoccurs, record the fault number, push the CANCEL
pad and contact an authorized servicer.
Faulty Installation
Place oven rack in center of oven. Place a level on the oven rack. Contact installing agent if rack and
cabinet cutout flooring are not level.
Kitchen cabinet misalignment may make oven appear to be not level. Be sure cabinets are square and
level. Contact cabinet maker to correct problem.
Entire Oven Does Not
Operate
Be sure electrical cord is securely connected into the electrical outlet.
Cord/plug is not installed and/or connected. Contact your dealer, installing agent or authorized servicer.
Service wiring not complete. Contact your dealer, installing agent or authorized servicer.
Power outage. Check house lights to be sure. Call your local electric company.
Short in cord/plug. Replace cord/plug.
Controls are not set properly. See instructions in this Use & Care Guide.
House fuse has blown or circuit breaker has tripped immediately following installation. House fuse may
not be fully engaged. Check fuse or engage circuit breaker securely.
House fuse has blown or circuit breaker has tripped after the oven has been installed and previously
operating. Call an authorized servicer.
Wall oven is not properly connected to gas supply. Check connection (see installation instructions).
Oven does not operate
Make sure gas supply shut-off valve is opened before turning on the oven after installingthe wall oven.
Oven Light Does Not
Work
Burned-out or loose bulb. Follow the instructions under Oven Light to replace or tighten the bulb.
Oven Smokes
Excessively During
Broiling
Oven door is opened. Oven door should be closed during broiling.
Meat too close to the broil burner. Reposition the rack to provide more clearance between the meat and
the broiler.
Meat not properly prepared. Remove excess fat from meat. Cut remaining fatty edges to prevent curling,
but do not cut into the lean.
Grid on broiler pan wrong side-up. Grease does not drain into broiler pan. Always place the grid on the
broiler pan with the ribs up and the slots down to allow grease to drip into the pan.
Broiler pan used without grid or grid cover with aluminum foil. DO NOT use the broiler pan without the
grid or cover the grid with aluminum foil.
Oven needs to be cleaned. Grease has built up on oven surfaces. Regular cleaning is necessary when
broiling frequently. Grease or food spatters cause excessive smoking.
Soil Not Completely
Removed After SelfCleaning Cycle is
Completed
Failure to clean bottom, from top of oven, frame of oven or door area outside oven seal. These areas
are not in the self-cleaning area, but get hot enough to burn on residue. Clean these areas before the
self-cleaning cycle is started. Burned on residue can be cleaned with a stiff nylon brush and water or a
nylon scrubber. Be careful not to damage the oven gasket.
Excessive spillovers in oven. Set the self-clean cycle for longer cleaning time.
Poor Baking Results
Many factors affect baking results. See Baking for hints, causes and corrections. See Adjusting Oven
Temperature.
If food items are too dark on the top or bottom, allow the oven to preheat to set temperature before
placing food in oven. Make sure the proper rack position is used when baking. Set temperature 25°F lower
than recommended. If food is not doe after recommended time, increase the set temperature 25°F.
Flames Inside Oven or
Smoke from Vent
Excessive spillovers in oven. This is normal, especially for high oven temperatures, pie spillovers or for
large amounts of grease on bottom of oven. Wipe up excessive spillovers.
15
MAJOR APPLIANCE WARRANTY
Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux
will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or
workmanship when such appliance is installed, used and maintained in accordance with the provided instructions.
Exclusions
This warranty does not cover the following:
1 Products with original serial numbers that have been removed, altered or cannot be readily
determined.
2 Product that has been transferred from its original owner to another party or removed outside the
USA or Canada.
3 Rust on the interior or exterior of the unit.
4 Products purchased "as-is" are not covered by this warranty.
5 Food loss due to any refrigerator or freezer failures.
6 Products used in a commercial setting.
7 Service calls which do not involve malfunction or defects in materials or workmanship, or for
appliances not in ordinary household use or used other than in accordance with the provided
instructions.
8 Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9 Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards,
shelves, etc., which are not a part of the appliance when it is shipped from the factory.
10Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumable, or
knobs, handles, or other cosmetic parts.
11Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry
trip charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12Damages to the finish of appliance or home incurred during installation, including but not limited to
floors, cabinets, walls, etc.
13Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or
external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
DISCLAIMER OF IMPLIES WARRANTIES; LIMITATION OF REMEDIES
Customer’s sole and exclusive remedy under this limited warranty shall be product repair or
replacement as provided herein. Claims based on implied warranties, including warranties of
merchantability or fitness for particular purpose, are limited to one year or the shortest period
allowed by law, but not less than one year. Electrolux shall not be liable for consequential or
incidental damages such as property damage and incidental expenses resulting from any breach
of this written limited warranty or any implied warranty. Some states and provinces do not allow
the exclusion or limitation of incidental or consequential damages, or limitations on the duration of
implied warranties, so these limitations or exclusions may not imply to you. This written warranty
gives you specific legal rights. You may also have other rights that vary from state to state.
If You
Need
Service
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained contacting Electrolux at the addresses or phone numbers below.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major
Appliances North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by
Electrolux Canada Corp. Electrolux authorizes no person to change or add to any obligations under this warranty.
Obligations for service and parts under this warranty must be performed by Electrolux or an authorized service
company. Product features or specifications as described or illustrated are subject to change without notice.
USA
1.800.944.9044
Electrolux Major Appliances
North America
P.O. Box 212378
Augusta, GA 30907
16
Canada
1.800.265.8352
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4
Download PDF

advertising