Instruction manual | Frymaster FPD65 Fryer User Manual

FPD65 Series with Built-In Filtration
Frymaster FPD65 Series
Gas Fryers
Installation & Operation Manual
PARTS LIST
INCLUDED
Frymaster, a member of the Commercial Food Equipment Service Association, recommends
using CFESA Certified Technicians.
24-Hour Service Hotline 1-800-551-8633
MARCH 2004
*8196039*
Please read all sections of this manual and retain for future reference.
NOTICE
This appliance is intended for professional use only and is to be operated by qualified
personnel only. A Frymaster/Dean Factory Authorized Service Center (FASC) or other qualified
professional should perform installation, maintenance, and repairs. Installation, maintenance,
or repairs by unqualified personnel may void the manufacturer’s warranty. See Chapter 1 of
this manual for definitions of qualified personnel.
NOTICE
This equipment must be installed in accordance with the appropriate national and local codes of
the country and/or region in which the appliance is installed. See NATIONAL CODE
REQUIREMENTS in Chapter 3 of this manual for specifics.
NOTICE
DANGER
Improper installation, adjustment, maintenance or service, and unauthorized alterations or
modifications can cause property damage, injury, or death. Read the installation, operating and
service instructions thoroughly before installing or servicing this equipment. Only qualified
service personnel may convert this appliance to use a gas other than that for which it was
originally configured. See Chapter 1 of this manual for definition of qualified service personnel.
DANGER
Adequate means must be provided to limit the movement of this appliance without depending
upon the gas line connection. Single fryers equipped with legs must be stabilized by installing
anchor straps. All fryers equipped with casters must be stabilized by installing restraining
chains. If a flexible gas line is used, an additional restraining cable must be connected at all
times when the fryer is in use.
DANGER
The front ledge of the fryer is not a step. Do not stand on the fryer. Serious injury can result
from slips or contact with the hot oil.
DANGER
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance.
DANGER
Instructions to be followed in the event the operator smells gas or otherwise detects a gas leak
must be posted in a prominent location. This information can be obtained from the local gas
company or gas supplier.
DANGER
The crumb tray in fryers equipped with a filter system must be emptied into a fireproof container
at the end of frying operations each day. Some food particles can spontaneously combust if left
soaking in certain shortening material. Additional information can be obtained in the filtration
manual included with the system.
WARNING
No structural material on the fryer should be altered or removed to accommodate placement of
the fryer under a hood. Questions? Call the Frymaster/Dean Service Hotline at 1-800-551-8633.
WARNING
Do not bang fry baskets or other utensils on the fryer’s joiner strip. The strip is present to seal
the joint between the frypot. Banging fry baskets on the strip to dislodge shortening will distort
the strip, adversely affecting its fit. It is designed for a tight fit and should only be removed for
cleaning.
FPD65 Series Gas Fryers
Installation & Operation Manual
TABLE OF CONTENTS
Page #
1.
INTRODUCTION
1-1
1.1
After Purchase
1-1
1.2
Ordering Parts
1-1
1.3
Service Information
1-1
1.4
Computer Information
1-1
1.5
Safety Information
1-2
1.6
Service Personnel
1-3
2.
IMPORTANT INFORMATION
2-1
2.1
Receiving and Unpacking Equipment
2-1
2.2
General
2-2
2.3
Principles of Operation
2-3
2.4
Rating Plate
2-3
2.5
Pre-Installation
2-3
2.6
Air Supply and Ventilation
2-5
2.7
Equipment Installed at High Altitudes
2-5
3.
INSTALLATION
3-1
3.1
Installing the Fryer
3-1
3.2
Gas Connections
3-4
3.3
Adjustments/Adaptation to Different Gases
3-7
3.4
Electrical Connections
3-9
4.
FRYER OPERATIONS
4-1
4.1
Initial Start-up
4-1
4.2
Boil-Out Procedure
4-3
4.3
Final Preparation
4-5
FPD65 Series Gas Fryers
Installation & Operation Manual
TABLE OF CONTENTS (CONT.)
Page #
5.
FILTRATION OPERATION
5-1
5.1
General
5-1
5.2
Filtration Preparation
5-1
5.3
Daily Filtration Operation
5-4
5.4
Operating the Filter
5-6
6.
PREVENTATIVE MAINTENANCE
6-1
6.1
General
6-1
7.
TROUBLESHOOTING
7-1
7.1
General
7-1
7.2
Pilot Burner Malfunction
7-2
7.3
Main Burner Malfunctions
7-2
7.4
Wiring Diagram, Main
7-4
7.5
Wiring Diagram, Filter
7-5
8.
PARTS LIST
8-1
8.1
Cabinetry and Related Components
8-1
8.2
Doors, Topcaps and Related Components
8-3
8.3
Frypots, Burners and Related Components
8-4
8.4
Component Box Components
8-6
8.5
Filter Pan and Related Components
8-7
8.6
Oil-Drain Components
8-8
8.7
Oil-Return Components
8-10
8.8
Suction Tube, Oil-Return Components
8-11
THIS PAGE INTENTIONALLY LEFT BLANK.
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 1: INTRODUCTION
1.1 After Purchase
In order to improve service, have the following chart filled in by the Frymaster/Dean Authorized
Service Technician who installed this equipment.
Authorized Service
Technician/FASC
Address
Telephone/Fax
Model Number
Serial Number
Gas Type
1.2 Ordering Parts
Customers may order parts directly from their local factory authorized service center. For this
address and phone number, contact your factory authorized service center or call the Frymaster/Dean
Service Hotline phone number, 1-800-551-8633.
To speed up your order, provide the model number, serial number, gas type, part needed, item part
number (if known), and quantity needed.
1.3 Service Information
Call the Frymaster/Dean Service Hotline, 1-800-551-8633, for the location of your nearest factory
authorized service center. To assist you more efficiently, always provide the service technician with
the model number, gas type, serial number, and the nature of the problem.
1.4 Computer Information
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. While this device is a verified Class A device, it has been
shown to meet the Class B limits. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of
the equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his/her own expense.
1-1
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 1: INTRODUCTION
1.4 Computer Information (cont.)
The user is cautioned that any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
If necessary, the user should consult the dealer or an experienced radio and television technician for
additional suggestions.
The user may find the following booklet prepared by the Federal Communications Commission
helpful: "How to Identify and Resolve Radio-TV Interference Problems". This booklet is available
from the U.S. Government Printing Office, Washington, DC 20402, Stock No. 004-000-00345-4.
1.5 Safety Information
Before attempting to operate your unit, read the instructions in this manual thoroughly.
Throughout this manual, you will find notations enclosed in double-bordered boxes similar to the
ones below.
CAUTION
CAUTION boxes contain information about actions or conditions that may cause or result in a
malfunction of your system.
WARNING
WARNING boxes contain information about actions or conditions that may cause or result in
damage to your system, and which may cause your system to malfunction.
DANGER
DANGER boxes contain information about actions or conditions that may cause or result in injury
to personnel, and which may cause damage to your system and/or cause your system to malfunction.
1-2
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 1: INTRODUCTION
1.6 Service Personnel
1.6.1 Definitions
A. Qualified and/or Authorized Operating Personnel
1.
Qualified/authorized operating personnel are those who have carefully read the information
in this manual and have familiarized themselves with the equipment functions, or have had
previous experience with the operation of equipment covered in this manual.
B. Qualified Installation Personnel
1.
Qualified installation personnel are individuals, or firms, corporations, or companies, which,
either in person or through a representative are engaged in and are responsible for the
installation of gas-fired appliances. Qualified personnel must be experienced in such work,
be familiar with all gas precautions involved, and have complied with all requirements of
applicable national and local codes.
C. Qualified Service Personnel
1.
Qualified service personnel are those who are familiar with Frymaster/Dean equipment and
have been authorized by Frymaster/Dean to perform service on Frymaster/Dean equipment.
All authorized service personnel are required to be equipped with a complete set of service
parts manuals and stock a minimum amount of parts for Frymaster/Dean equipment. A list
of Frymaster/Dean Factory Authorized Service Centers (FASCs) was included with the fryer
when shipped from the factory. Failure to use qualified service personnel will void the
Frymaster/Dean warranty on your equipment.
1-3
THIS PAGE INTENTIONALLY LEFT BLANK.
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 2: IMPORTANT INFORMATION
2.1 Receiving and Unpacking Equipment
A. Check that the containers are upright. Use an outward prying motion - no hammering - to
remove the cartons. Unpack fryers carefully and remove all accessories from the carton
and/or frypots. Do not discard or misplace accessories, as they will be needed during final
assembly and fryer operation.
B. After unpacking, immediately check the equipment for visible signs of shipping damage. If
damage has occurred, contact the carrier and file the appropriate freight claims. Do not
contact the factory. Shipping damage responsibility is between the carrier and the dealer.
If your equipment arrives damaged:
1. File claim for damages immediately, regardless of extent of damage.
2. Visible loss or damage: Be sure this is noted on the freight bill or express receipt and is
signed by the person making the delivery.
3. Concealed loss or damage: If damage is unnoticed until equipment is unpacked, notify
freight company or carrier immediately, and file a concealed damage claim. This should
be done within 15 days of date of delivery. Be sure to retain container and all packing
materials for inspection.
NOTE: Frymaster/Dean Does Not Assume Responsibility for Damage or Loss Incurred
in Transit.
C. Built-in filtration cabinet: Remove the filter pan from the cabinet before removing system
from pallet.
D. Five- and Six-battery Frying Systems: Units are shipped on two pallets. Casters are preinstalled on the frying system and unloading ramps are furnished to facilitate removal of the
units off the pallets. Remove pallet supports from underneath fryer and carefully roll the unit
down the ramps from the front (cooking side). See assembly instructions shipped with
unit for system assembly.
E. Remove all plastic skin from sides, front, and doors of the fryers. Units are shipped with
plastic skin to protect the stainless components from surface damage during shipping.
Failure to remove the plastic prior to initial fryer operation will make it very difficult to
remove later.
2-1
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 2: IMPORTANT INFORMATION
2.2 General
Qualified, licensed, and/or authorized installation or service personnel only (as defined in
Section 1.6) should perform the following:
•
Installation and service on Frymaster/Dean equipment.
•
Conversion of this appliance from one gas type to another.
Failure to use qualified, licensed, and/or authorized installation or service personnel to install,
convert to another gas type or otherwise service this equipment will void the Frymaster/Dean
warranty and may result in damage to the equipment or injury to personnel.
Where conflicts exist between instructions and information in this manual and local code or
national codes, or regulations, installation and operation shall comply with the codes or
regulations in force in the country in which the equipment is installed.
DANGER
Building codes prohibit a fryer with its open tank of hot oil/shortening from being
installed beside an open flame of any type, including those of broilers and ranges.
Upon arrival, inspect the fryer carefully for visible or concealed damage. (See Receiving and
Unpacking Equipment in Section 2.1.)
2.2.1 Product Description
Frymaster FPD65 Series gas fryers are energy efficient, tube-style, gas-fired units. All units are
shipped completely assembled with accessories packed inside the frypot. Frymaster FPD65 Series
gas fryers are adjusted, tested and inspected at the factory before shipment. The input rates of this
model are listed in this manual.
WARNING
The on-site supervisor is responsible for ensuring that operators are made aware of
the inherent hazards of operating a hot oil frying system, particularly the aspects of
system operation, oil filtration, draining and cleaning procedures.
2-2
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 2: IMPORTANT INFORMATION
2.3 Principles of Operation
The incoming gas flows through orifices and is mixed with air in the burners to create the correct
ratio for proper combustion. The mixture is ignited at the front end of each heat tube by the pilot
light. Internal diffusers slow the flame as it goes through the burner tube. This slower and more
turbulent flame gives much better heat transfer to the walls of the tubes, thereby heating the oil
better.
2.4 Rating Plate
This is attached to the inside front door panel. Information provided includes the model and serial
number of the fryer, BTU/hr input of the burners, outlet gas pressure in inches W.C. and whether the
unit has natural or propane gas orifices.
DANGER
Fryers MUST be connected ONLY to the gas type identified on the attached rating
plate.
2.5 Pre-Installation
DANGER
No structural material on the fryer should be altered or removed to accommodate
placement of the fryer under a hood. Questions? Call the Frymaster/Dean Service
Hotline at 1-800-551-8633.
DANGER
Do not connect this appliance to the gas supply before reviewing all information in
this chapter.
A. General: Only licensed personnel should install any gas-fired equipment.
1.
A manual gas shut-off valve must be installed in the gas supply line ahead of the fryers for
safety and ease of future service.
2.
Frymaster FPD65 Series gas fryers require 120VAC 60 cycle or 230VAC single-phase 50hertz (International/CE) electrical service and are equipped with a 16-3 SJT grounded
flexible power cord for a direct connection to the power supply. Amperage draw for each
unit depends on the accessories supplied with the unit/system.
2-3
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 2: IMPORTANT INFORMATION
2.5 Pre-Installation (cont.)
B. Clearances: The fryer area must be kept free and clear of all combustibles. This unit is designcertified for the following installations:
1.
Commercial installation only (not for household use).
2.
Non-combustible floor installation equipped with factory-supplied 6-inch (15-cm) adjustable
legs or 5-inch (13-cm) casters;
3.
Combustible construction with a minimum clearance of 6-inches (15-cm) side and 6-inches
(15-cm) rear, and equipped with factory-supplied 5-inch (13-cm) casters.
C. Installation Standards
1.
2. Canadian installations must meet:
U.S. installations must meet:
American National Standard Institute
ANSI Z83.11
American Gas Association
8501 E. Pleasant Valley Road
Cleveland, OH 44131
CAN 1-B149 Installation Codes
Canadian Gas Association
55 Scarsdale Road
Don Mills, ONT, M3B 2R3
National Electrical Code
ANSI/NFPA #70
American National Standard Institute
1430 Broadway
New York, NY 10018
Canadian Electric Code c22.1, part 1
Canadian Standards Association
178 Rexdale Blvd.
Rexdale, ONT, M9W 1R3
NFPA Standards #96 and #211
National Fire Protection Association
470 Atlantic Avenue
Boston, MA 02110
2-4
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 2: IMPORTANT INFORMATION
2.6 Air Supply and Ventilation
DANGER
This appliance must be installed with sufficient ventilation to prevent the occurrence
of unacceptable concentrations of substances harmful to the health of personnel in
the room in which it is installed.
Keep the area around the fryer clear to prevent obstruction of combustion and ventilation airflow as
well as for service and maintenance.
A. Do not connect this fryer to an exhaust duct.
B. Correct installation and adjustment will ensure adequate airflow to the fryer system.
C. A commercial, heavy-duty fryer must vent its combustion wastes to the outside of the
building. A deep-fat fryer must be installed under a powered exhaust hood, or an exhaust fan
must be provided in the wall above the unit, as exhaust gas temperatures are approximately
800-1000°F (427-538°C). Check air movement during installation. Strong exhaust fans in
the exhaust hood or in the overall air conditioning system can produce slight air drafts in the
room.
D. Do not place the fryer’s flue outlet directly into the plenum of the hood, as it will affect the
gas combustion of the fryer.
E. Never use the interior of the fryer cabinet for storage or store items on shelving over or
behind the fryer. Exhaust temperatures can exceed 800°F (427°C) and may damage or melt
items stored in or near the fryer.
F. Adequate distance must be maintained from the flue outlet of the fryer(s) to the lower edge
of the filter bank. Per NFPA Standards No. 96, a minimum of 18-inches (45-cm) should be
maintained between the flue(s) and the lower edge of the exhaust hood filter.
G. Filters and drip troughs should be part of any industrial hood, but consult local codes before
constructing and installing any hood. The duct system, the exhaust hood and the filter bank
must be cleaned on a regular basis and kept free of grease.
2.7 Equipment Installed at High Altitudes
A. The fryer input rating (BTU/hr) is for elevations up to 2,000 feet (610-m). For elevations
above 2,000 feet (610-m), the rating should be reduced four percent for each additional 1,000
feet (305-m) above sea level.
B. The correct orifices are installed at the factory if operating altitude is known at time of the
customer’s order.
2-5
THIS PAGE INTENTIONALLY LEFT BLANK.
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 3: INSTALLATION
3.1 Installing the Fryer
Decathlon 65 Series fryer systems are shipped in sections. The fryers are uncrated, removed from
pallets and assembled together. Important aspects during assembly include aligning and connecting
the drain system, oil return system, rinse-line system (where applicable), oil-return switch wiring
harness and fryer cabinets. Slight modifications to connecting hardware may be required when
assembling the system. The instructions below provide step-by-step instructions to assist the
installer in assembly. For this procedure, the fryers are numbered from right to left as follows:
Fryers #1, #2, #3, #4, #5 and #6 (where applicable).
1. Open the doors of the filtration fryer cabinet.
Remove filter pan from the cabinet. Uncrate
fryers and remove the pallet supports. Install
ramps and slowly roll the fryer(s) off the pallets.
Figure 1. Remove pallet supports (arrow)
before removing fryers from pallets.
2. Remove door from fryers to be connected by
lifting the door upward and removing the door
pin from the bottom hinge. Remove slip-nuts
from drain-tees on fryers being connected,
lubricate O-rings with vegetable oil and install
on drainpipe (Fig. 2). Use care not to damage
the slip-nut O-rings when installing slip-nut on
drainpipe. Insert the drainpipe into the fryer
drain-tee (Fig. 3). Screw slip-nut onto the tee
but do not tighten at this time. Position fryers
being connected within 6 inches of each other,
near the permanent installation area. Guide the
drainpipe through the opposite fryer cabinet
opening as the cabinets are positioned.
Properly align the drainpipe evenly between the
two drain-tees using the "blue" marks on the tube
ends to prevent leaks and/or blocked drain
valves.
Figure 2. Slip-nut/drainpipe detail.
NOTE: When the slip nuts are tightened, the
"blue" marks on each end of the drainpipe
should align to the outside edge of each slip
nut.
Figure 3. Insert drainpipe section into fryer
drain-tee before pushing fryers together
(arrow). Do this as required for all cabinets
being assembled.
3-1
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 3: INSTALLATION
3.1 Installing the Fryer (cont.)
3. Connect red/white or red/yellow wires (Figure 4,
left) between fryer sections being assembled
(Figure 4, right, arrow). Oil-return will not
operate properly if these wires are not connected.
NOTE: On systems shipped in three or more
sections, additional wiring between cabinets
will exist. Ensure all wires are connected
before completing cabinet assembly.
4. Remove the lower back panel-strips on fryers
being assembled to gain access to the oil return
and rinse-line connections (Figure 5, arrows).
Back removal may not be required on some
systems.
5. Slowly push the two cabinets together. Ensure
the drainpipe and slip-nut are aligned with the
drain-tee on the opposite fryer section. Ensure
the oil-return and rinse-hose connections (where
applicable) on each fryer section are aligned.
Ensure oil-return switch wires between cabinet
sections are not pinched when the cabinets are
brought together. Pull excess wire through the
opposite fryer side as the cabinets are brought
together. Secure excess wire inside cabinet with
a wire tie.
6.
Figure 4. Oil return wires between sections
must be connected for oil-return operation.
Figure 5. Oil return and rinse-line (where
applicable) connections.
With the cabinets together, insert the drainpipe
into the opposite fryer drain-tee and position it
evenly between the fryers being connected.
Connect the oil-return and rinse-lines by
accessing the oil return union through the lower
fryer-back openings. Connect all fittings, but do
not tighten at this time.
7. Align the cabinet connection holes, front and
back (Figure 6, arrow). Connection hardware is
included in the accessories pack. Insert bolts and
install nuts, but do not tighten. If holes do not
align, use a 3/16" drill-bit and drill through the
misaligned hole.
Figure 6. Cabinet connection locations
inside cabinet sections (front shown).
8. Install the frypot joiner strip between cabinet
sections (Figure 7; also see factory-installed
strips on two-battery cabinet sections).
Figure 7. Install joiner strip(s) after fryers
are connected.
3-2
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 3: INSTALLATION
3.1 Installing the Fryer (cont.)
9. Install the front connecting post on the connected
cabinets (Figure 8; see factory-installed posts on
two-battery fryer sections).
10. Complete installation of topcap battering strips
after the front connecting post has been installed
(Figure 9).
Figure 8. Installing front connecting post
on connected fryer sections.
NOTE: Systems shipped in three or more
sections will require the installation of topcaps
and other components prior to installing
topcap-battering strips.
See Topcap
Installation Instructions for these systems.
11. Install the rear connecting plate (Figure 10).
Remove four screws from the cabinet backs
(Figure 10, arrows), install connecting plate and
replace screws. Connection strips vary from
system to system.
12. At the fryer front: Tighten the drain manifold
slip-nuts. Install doors removed at the beginning
of assembly. At the fryer back: Tighten the oilreturn line and rinse-line (where applicable)
union(s).
Figure 9. Complete installation of topcap
battering strips (arrow) after installing
front connecting post(s) on connected
fryers.
13. Reinstall filter pan after fryer start-up has been
performed (boil-out, burner adjustment, etc.)
NEVER ALLOW WATER OR BOILOUT
SOLUTION INTO FILTER SYSTEM.
Check all connections for leaks.
components operate properly.
Ensure all
Figure 10. Install rear connecting plate.
3-3
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 3: INSTALLATION
3.1 Installing the Fryer (cont.)
DANGER
Fryers must be at room temperature and empty of oil during movement to avoid
damage and possible bodily injury.
DANGER
Hot shortening can cause severe burns. Avoid contact. Under all circumstances, oil
must be removed from the fryer before attempting to move it to avoid oil spills, and
the falls and severe burns that could occur. This fryer may tip and cause personal
injury if not secured in a stationary position.
3.2 Gas Connections
DANGER
Before connecting new pipe to this appliance the pipe must be blown out thoroughly
to remove all foreign material. Foreign material in the burner and gas controls will
cause improper and dangerous operation.
NATIONAL CODE REQUIREMENTS
This equipment is to be installed in compliance with the Basic Plumbing Code of the Building
Officials and Code Administrators International, Inc. (BOCA) and the Food Service Sanitation
Manual of the U.S. Food and Drug Administration.
This equipment is manufactured to use the type of gas specified on the rating plate attached to the
door. Connect equipment stamped "NAT" only to natural gas and that stamped "PRO" only to LP
(Propane) gas.
Notice
Installation shall be made with a gas connector that complies with national and local codes.
Quick disconnect devices, if used, shall likewise comply with national and local codes.
DANGER
The fryer MUST be connected to the gas supply specified on the rating and serial
number plate located on the back of the fryer door.
3-4
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 3: INSTALLATION
3.2 Gas Connections (cont.)
DANGER
If gas odors are detected, the gas supply MUST be shut off at the main shut-off
valve. The local gas company or FASC should be contacted immediately to rectify
the problem.
A. The gas supply (service) line must be the same size or greater than the fryer inlet line. This
fryer system is equipped with three 1" (28 mm) female inlets (one inlet per two fryers). The
gas supply line must be sized to accommodate all the gas-fired equipment that may be
connected to that gas supply. Consult your contractor, gas company, supplier, or other
knowledgeable authorities.
Recommended Gas Supply Line Sizes
Gas Types
Number of Fryers
1
2 to 3
4 or more (*)
Natural Gas
3/4" (22 mm)
1" (28 mm)
1-1/4" (35 mm)
Propane Gas
1/2" (15 mm)
3/4" (22 mm)
1" (28 mm)
(*) When exceeding 18 feet for a configuration of more than four fryers, it is necessary to provide
a 1-1/4" (35 mm) rigid gas connection.
DANGER
All connections must be sealed with a joint compound suitable for the gas being
used and all connections must be tested with a solution of soapy water before
lighting any pilots.
Never use matches, candles, or any other ignition source to check for leaks. If gas
odors are detected, shut off the gas supply to the appliance at the main shut-off
valve and immediately contact the local gas company or an authorized service
agency for service.
DANGER
"Dry-firing" your unit will cause damage to the frypot and can cause a fire. Always
ensure that melted shortening, cooking oil or water is in the frypot before firing the
unit.
B. Rigid Connections: Check any installer-supplied intake pipe(s) visually and clean threading
chips, or any other foreign matter before installing into a service line. If the intake pipes are
not clear of all foreign matter, the orifices will clog when gas pressure is applied. Seal pipe
joints with a sealant resistive to LP gas. When using thread compound on gas piping, use
very small amounts and only on male threads. Use a pipe thread compound that is not
affected by the chemical action of LP gases. DO NOT apply thread compound to the first
two pipe threads—doing so will cause clogging of the burner orifices and control valve.
3-5
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 3: INSTALLATION
3.2 Gas Connections (cont.)
C. Manual shut-off valve: This gas service supplier-installed valve must be installed in the gas
service line ahead of the fryers in the gas stream and in a position where it can be reached
quickly in the event of an emergency.
D. Regulating Gas Pressure: The fryer and shut-off valve must be disconnected from the gas
supply during any pressure testing of the system.
1. External gas regulators are not normally required on this fryer. A safety control valve
protects the fryer against pressure fluctuations. If the incoming pressure is in excess of
½" PSI (3.45 kPa/35 mbar), a step-down regulator will be required.
DANGER
When pressure-testing incoming gas supply lines, disconnect the fryer from the gas
line if the test pressure is ½" PSI [3.45 kPa (14 inches W.C.)] or greater to avoid
damage to the fryer’s gas piping and gas valve(s).
E. Manifold Pressure: Your local service technician should check the manifold pressure with a
manometer.
3-6
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 3: INSTALLATION
3.2 Gas Connections (cont.)
I.
Flexible Couplings, Connectors and Casters:
1. If the fryer is to be installed with flexible couplings and/or quick-disconnect fittings, the
installer must use a heavy-duty AGA design-certified commercial flexible connector of
at least 1" NPT (with suitable strain reliefs), in compliance with the Standard for
Connectors for Movable Gas Appliances, ANSI Z21.69-(latest edition) and Addenda
Z21.69a-(latest edition). Quick disconnect devices must comply with the Standard for
Quick-Disconnect Devices for Use with Gas Fuel, ANSI Z21.41-(latest edition).
WARNING
Do not attach accessories to this fryer unless fryer is secured from tipping.
Personal injury may result.
2. The fryer must be restrained by means independent of the flexible coupling or
connector in order to limit the movement of the fryer. Clips are located on the back
panel of the fryer for the attachment of restraints.
3. If disconnection of the restraint is necessary, this restraint must be reconnected after the
fryer has been returned to its originally installed position.
J. After hook-up, bleed the gas line of air to ensure that the pilot light will ignite quickly.
3.3 Adjustments/Adaptation To Different Gases
A. Proper operation of Frymaster/Dean gas fryers requires operator to inspect the following
adjustments in terms of:
1. Gas inputs and pressures.
2. Voltage and polarities of electrical power supplies.
B. Frymaster/Dean gas fryers are manufactured to use the type of gas and pressure specified on
the rating plate. When changing to a different gas, adaptation must be performed by
qualified personnel. Failure to use qualified personnel will void the Frymaster/Dean
warranty.
3-7
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 3: INSTALLATION
3.3.1 Specifications
3.3.1.1 Adjustments to Different Gas Types
Gas Adjustments
Gas Type
Natural
LP
4" W.C.*/10 mbar*
11" W.C.*/27.5 mbar*
Orifice Diameter
Model Specific
Model Specific
Burner Marking
None
None
26N (P/N 810-0811)
16LP (P/N 810-2400)
Manifold Pressure†
Pilot Marking
* Gas pressure may vary per fryer model and altitude. Check the rating plate for specific
gas pressures.
NOTE: Outlet gas pressure must be adjusted strictly within the above requirements 5 to 10 minutes
after the appliance is operating.
† For controls and adjustments, please refer to the "gas valve" illustration on page 3-9. (Pilot Flame
Adjustment: Turn the pilot adjustment screw clockwise/counter-clockwise until the desired flamevolume is achieved.)
3.3.2 Gas Conversion Procedures
DANGER
This appliance was configured at the factory for a specific type of gas. Converting
from one gas type to another requires the installation of specific gas-conversion
components.
Switching to a different type of gas without installing the proper conversion
components may result in fire or explosion. NEVER ATTACH THIS APPLIANCE TO A
GAS SUPPLY FOR WHICH IT IS NOT CONFIGURED!
Conversion of this appliance from one type of gas to another should only be
performed by qualified, licensed, and authorized installation or service personnel, as
defined in Section 1.6 of this manual.
3-8
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 3: INSTALLATION
3.3.2 Gas Conversion Procedures (cont.)
Contact factory with the following information when performing conversions:
•
•
•
•
Fryer Serial Number
Fryer Model Number
Gas Type
Operating Altitude
Conversions can only be executed by qualified, factory-authorized personnel.
Pilot pressure adjustment
(remove cover screw to access)
Pressure flow adjustment
(remove cover screw to access)
Typical gas valve
Regulator Vent
Pilot gas supply connection.
ON/OFF Gas-Cock Knob
3.4 Electrical Connections
The fryer when installed must be electrically grounded in accordance with local codes, or in the
absence of local codes, with the National Electrical Code, ANSI/NFPA 70-(latest edition).
DANGER
This fryer is equipped with three-prong (grounding) plugs for protection against
electrical shock and must be plugged directly into a properly grounded, three-prong
receptacle. DO NOT CUT, REMOVE, OR OTHERWISE BYPASS THE GROUNDING
PRONGS ON THESE PLUGS!
The rating plate and wiring diagram are located inside the front door. The fryer is equipped with a
120VAC single-phase 60-hertz system (Domestic), or 230VAC single-phase 50-hertz system
(International/CE). Do not cut or remove the ground prong from any of the power cord plugs. Do
not attempt to use the fryer during a power outage.
DANGER
This appliance requires electrical power for operation. Place the gas control valve in
the OFF position in case of a prolonged power outage. Do not attempt to operate
this appliance during a power outage.
3-9
THIS PAGE INTENTIONALLY LEFT BLANK.
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 4: FRYER OPERATIONS
4.1 Initial Start-up
WARNING
The on-site supervisor is responsible for ensuring that operators are made aware of
the inherent hazards of operating a hot oil frying system, particularly the aspects of
system operation, oil filtration, draining and cleaning procedures.
Cleaning: New units are wiped clean with solvents at the factory to remove any visible signs of dirt,
oil, grease, etc. remaining from the manufacturing process, then coated lightly with oil. Before any
food preparation, wash thoroughly with hot, soapy water to remove any film residue and dust or
debris then rinse out and wipe dry. Also wash any accessories shipped with the unit. Close the drain
valve completely and remove the crumb screen covering the heating tubes. Ensure the screws
holding the thermostat and high-limit control sensing bulbs into the frypot are tight.
Typical high-limit/sensor probe locations and mounting hardware.
WARNING
Do not bang fry baskets or other utensils on the fryer’s joiner strip. The strip is
present to seal the joint between the frypot. Banging fry baskets on the strip to
dislodge shortening will distort the strip, adversely affecting its fit. It is designed for
a tight fit and should only be removed for cleaning.
DANGER
Never operate this appliance with an empty frypot. The frypot must be filled with
water or cooking oil/shortening before lighting the burners. Failure to do so will
damage the frypot and may cause a fire.
WARNING
When checking for burner ignition or performance, do not get too close to the
burners. Slow ignition can cause possible flashback, increasing the potential for
facial and body burns.
4-1
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 4: FRYER OPERATIONS
4.1.1 Pilot Lighting Procedures, Electronic Ignition Systems
Initial Pilot Lighting: All Frymaster/Dean fryers are tested, adjusted and calibrated to sea level
conditions before leaving the factory. Adjustments to assure proper operation of pilot may be
necessary on installation to meet local conditions, low gas pressure, differences in altitude and
variations in gas characteristics. These adjustments correct possible problems caused by rough
handling or vibration during shipment, and are to be performed only by qualified service personnel.
These adjustments are the responsibility of the customer and/or the dealer and are not covered by the
Frymaster/Dean warranty.
The inlet pipe at the lower rear of the fryer brings incoming gas to the pilot safety control valve, then
to the pilot and main burners. The pilot is located high in the cabinet center, at the base of the
frypot.
WARNING
Never use a match or taper to light pilot on this ignition system.
1. Turn gas "ON".
2. Turn electric power "ON" with the appropriate rocker switch or controller/computer.
3. The ignition module will energize the pilot gas supply and the ignitor. The ignitor spark will
ignite the pilot gas. The presence of the pilot flame is then proved by a flame sensor, which
sends a signal to the main gas supply, opening the valve. The operating thermostat or
computer/controller controls the fryer after ignition.
WARNING
In the event of prolonged power failure, the ignition module will shut down and lock
out the system. Turn the unit power "OFF" and them back "ON" after power has
been re-established.
4. If the pilot flame fails, the ignition module will shut down and lock out the system. To restart,
turn the electric power "OFF", wait approximately 5 minutes for the system to recycle itself, then
turn the power "ON" again. Repeat Steps 1-3.
4-2
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 4: FRYER OPERATIONS
4.2 Boil-Out Procedure
DANGER
Never leave the fryer unattended during the boil-out process. If the boil-out solution
boils over, turn the fryer off immediately and let the solution cool for a few minutes
before resuming the process. To lessen the chance of boil over, turn the fryer’s gas
valve knob to the PILOT position occasionally.
WARNING
Do not drain boil-out solution into a shortening disposal unit, a built-in filtration unit,
or a portable filter unit. These units are not intended for this purpose, and will be
damaged by the solution.
DANGER
Remove all drops of water from the frypot before filling with cooking oil or
shortening. Failure to do so will cause spattering of hot liquid when the oil or
shortening is heated to cooking temperature and may cause injury to nearby
personnel.
A. Pour cleaning solution into the frypot and add water to the bottom OIL LEVEL line scribed
in the back of the frypot.
B. Operating thermostat-equipped fryers: Set dial/temperature controller to 225°F (107ºC), just
above that of boiling water.
C. Filtration/Boil-Mode equipped fryers: Turn fryer power switch to "ON". Press the fryerreset switch (if applicable). Turn the boil-out switch "ON".
CAUTION
If the pilot and main burner go out, the fryer(s) MUST be left completely shut down at
least 5 minutes before lighting.
D. The main burner will ignite.
E. When the solution nears boiling point, reset the temperature controller to 200°(93ºC).
F.
The burners should shut off just as the water starts to boil.
CAUTION
Do not leave fryer unattended. The boil-out solution may foam and overflow if fryer is
left unattended. Press ON/OFF switch to the "OFF" position (Filtration/Boil-Mode
equipped fryers) or reduce temperature (Operating Thermostat equipped fryers) to
control this condition.
4-3
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 4: FRYER OPERATIONS
4.2 Boil-Out Procedure (cont.)
G. The burners will heat the boil-out solution to a simmer. Simmer the solution for
approximately 45 minutes. Wearing protective gloves, scrub the sides of the frypot and the
tubes with the L-shaped Teflon brush, being careful not to disturb the temperature sensing
probes and the high-limit thermostat.
H. Do not allow the water level to decrease below the bottom OIL LEVEL line in frypot during
boil-out operation.
WARNING
Water or boil-out solution MUST not be allowed to drain into the filter pan or filter
system. Irreversible damage will result if water is allowed into the system.
I.
After boil out is complete, turn the computer off. Drain the solution from the frypot. Place
a metal stockpot of sufficient size to safely hold the entire contents of the frypot under the
drain port to collect the water/boil-out solution. Do not allow water or boil-out solution to
drain into the filter pan. The filter pump is not designed for water operation, and will be
irreparably damaged (see warning statement above).
J.
Close the drain, add fresh water (without boil-out solution) and wash all surfaces of the
frypot. Drain again.
K. Refill the frypot with fresh water and vinegar to neutralize any residual boil-out solution.
Wash all surfaces of the frypot. Drain completely and wipe down all surfaces of the frypot
to completely remove all water.
Computer-equipped fryers: See computer manual for boil-out programming and follow the
above procedures for boil-out.
DANGER
Do not go near the area directly over the flue outlet while the fryer is operating.
Always wear oil-proof, insulated gloves when working with the fryer filled with hot
oil.
Always drain hot oil into a metal stockpot of sufficient size to safely hold the entire
contents of the frypot.
4-4
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 4: FRYER OPERATIONS
4.3 Final Preparation
WARNING
NEVER set a complete block of solid shortening on top of heating tubes. To do so
will damage the heating tubes and frypot, and void the warranty.
4.3.1 Filling Fryer with Cooking Oil/Shortening
A. When using a liquid shortening (cooking oil), fill the fryer to the bottom OIL LEVEL line
scribed into the back of the frypot.
B. When using a solid shortening, cut it into small pieces and pack it below the heat tubes,
between the tubes and on top of the tubes, leaving no air spaces around the tubes. Do not
disturb or bend the probe sensing bulbs.
C. Press the computer on/off switch to "ON". The burners will initially operate in the MELT
CYCLE mode until the shortening reaches 180°F. It will then automatically switch to
normal operation.
D. When the frypot is filled and the shortening is melted, carefully replace the crumb screen
over the heat tubes. Wear oil-proof insulated gloves to avoid the potential for burn injury
when placing crumb screen in frypot.
For additional computer instructions, see computer manual that came with
frying system.
4-5
THIS PAGE INTENTIONALLY LEFT BLANK.
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 5: FILTRATION OPERATION
WARNING
Drawings and photos used in this manual are intended to illustrate operational,
cleaning and technical procedures and may not conform to on-site management
operational procedures.
5.1 General
Frymaster FPD65 Series gas fryer filter systems come equipped with a filter-leaf assembly, which
eliminates the need for filter paper. Filter powder is used to enhance the filtration process.
5.2 Filtration Preparation
On initial installation and before each use, remove all loose parts from the filter, wash the filter pan
and all accessories in hot, soapy water and dry thoroughly.
5.2.1 Assembling the Filter
Frymaster FPD65 Series filter systems incorporate a filter-leaf assembly, in which a fine mesh
screen is used to filter impurities and debris from the oil. The oil is pumped through the screen and
then returned to the frypot.
Assemble the filter pan as follows (see illustration below):
1. Filter pan assembly.
2. Filter-leaf assembly.
3. Crumb screen.
5
4
4. Front filter pan cover.
5. Rear filter pan cover.
2
3
1
5-1
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 5: FILTRATION OPERATION
5.2.1 Assembling the Filter (cont.)
Assemble the filter as follows:
1. Remove the filter pan covers.
Filter pan with covers removed.
2. Place the filter leaf assembly in the bottom of
the filter pan, ensuring the filter disconnect is
properly placed in the filter pan slot. Support
the screen assembly by holding the supply
pipe during installation.
The bracket fits into a slot in the pan.
3. Ensure the filter screen lies flat in the bottom
of the pan and the supply connection bracket
is properly positioned in the pan slot before
proceeding.
Filter leaf properly positioned in filter pan.
5-2
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 5: FILTRATION OPERATION
5.2.1 Assembling the Filter (cont.)
4. Place the crumb tray in filter pan.
Crumb screen placement in filter pan.
5. Replace the pan covers and install the filter
pan into the cabinet. Ensure the connections
are fully engaged. Ensure the filter pan
opening is directly under the drain tubes to
avoid splashing hot oil. The fryer is ready for
filtering.
The filter pan slides under the
fryer (above), connecting with a
slip fitting (right). The slip fitting
is located between the drain
tubes (above, arrow).
5-3
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 5: FILTRATION OPERATION
5.3 Daily Filtration Operation
WARNING
Use caution and wear proper protective clothing. The oil to be filtered is at or near
350°F (177°C). Ensure all hoses are connected properly and drain handles are in
their proper position prior to operating any switches or valves. Failure to do this can
result in severe burns.
WARNING
Drawings and photos used in this manual are intended to illustrate operational,
cleaning and technical procedures and may not conform to on-site management
operational procedures.
5.3.1 General Overview
The filter pump is turned on only after the oil is brought to operating temperature and drained into
the prepared filter pan. The filter motor is then engaged and oil is drawn through the filter leaf
assembly and pumped back into the frypot. The frypot drain valve remains open during the filtering
process. The oil is cycled through the filter leaf assembly for approximately 10 minutes (see
computer section for specific instructions). At the end of 10 minutes, the drain valve is closed,
allowing the oil to pump back into the frypot. The pump should run for 15-30 seconds after bubbles
appear in the frypot to ensure all oil or shortening is pumped from the drain pan and the oil-return
lines. The frypot oil level should return to the top OIL LEVEL line. If not, add fresh oil or
shortening to obtain the proper level. Remember, the oil is at operating temperature during all
filtration procedures.
The filter pump can be activated with a manual On/Off switch located under the fryer control panel
if the oil-return, drain-flush or wand/dispose valves fail to activate the pump when opened. Contact
an authorized service technician immediately for repair.
Refer to specific store procedures for correct filter operation. Additional information can be found
in the computer section of this manual.
NOTICE
Procedures explained in this chapter are specific to the CM4-S programmed filter
procedure.
5-4
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 5: FILTRATION OPERATION
5.3.2 Filtering Tools
Assemble tools to be used for filtering. These are supplied with the filter starter kit included with
the fryer/filter system:
•
•
Frypot/Filter Brush– used to clean frypot and filter pan sides and bottom, heating tubes, and
to dislodge sediment during filtration or shortening change.
Clean-Out Rod– used to dislodge heavy debris in the drain tube (when needed).
The following tools are not required, but are recommended:
•
•
Measuring Cup– used to measure filter powder.
Fine Mesh Skimmer– used to remove large debris.
Note: Prior to proceeding, put on safety goggles, neoprene gloves and heavy
vinyl apron.
NOTICE
Follow specific store procedures when filtering the fryer. In the event store
procedures are not available, the following instructions can be followed until specific
store procedures are obtained.
WARNING
Filter ONLY one frypot at a time. The filter pan is designed to hold the contents of
one frypot ONLY.
5-5
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 5: FILTRATION OPERATION
5.4 Operating the Filter
5.4.1 Filter Operation
CAUTION
NEVER operate the filter unit unless cooking oil is at operating temperature [~350°F
(~177°C)].
1. Remove fry baskets from frypot. Prior to
filtering, skim any large debris from the oil
with the fine mesh skimmer. Use extreme
caution, as oil is at or near operating
temperature [~350°F (~177°C)]. Use a metal
scraper to gently remove debris from frypot
walls above shortening level.
Prior to filtering, skim any large debris from oil in
frypot.
2. Pour 12 ounces by volume of filter powder
into the vat. Carefully stir the powder into
the oil with the fine mesh skimmer.
Adding filter powder to vat prior to filtering.
3. Ensure the oil is at operating temperature
(~350°F/177°C). Open the fryer drain valve.
Allow the oil to drain into the filter pan. The
computer will display OPEN DRAIN.
Pull red handle to open drain valve and allow hot
shortening to drain into filter pan.
5-6
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 5: FILTRATION OPERATION
5.4.1 Filter Operation (cont.)
4. When all the oil has drained from the frypot,
connect the hose-wand assembly to the
disconnect valve in the fryer cabinet. DO
NOT ACTIVATE FILTER PUMP UNTIL
THE HOSE HAS BEEN PROPERLY
CONNECTED. Ensure the hose-disconnect
is properly connected before proceeding.
Remove the frypot wire rack prior to rinsing
frypot.
Hose/wand disconnect properly connected to
disconnect valve in fryer cabinet (orientation of
disconnect may vary according to system).
5. Place the hose wand into the frypot being
filtered and activate the rinse valve by turning
the blue handle to "WAND" (where
applicable), or by pressing the manual bypass
switch (systems without oil disposal system).
The filter pump will activate and oil will start
flowing through the rinse hose.
After the hose wand end is properly positioned in
the frypot, activate the filter pump by turning the
blue handle to "WAND" (where applicable).
6. Hold the wand inside the frypot at a 45degree angle while the rinse valve is opened.
7. Use the wand to rinse debris from the frypot
for approximately 3 minutes. At the end of 3
minutes, the computer display will alternate
from OPEN DRAIN to the timed
countdown cycle (10 minutes). Turn the blue
handle or the manual bypass switch to "OFF",
and then close the drain valve (red handle).
Disconnect and drain the hose of all
shortening or oil. Hang hose upright to
ensure no shortening remains in hose.
5-7
Use the wand to rinse debris from the frypot into
the filter pan. Maintain a firm grip on the wand
handle at all times.
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 5: FILTRATION OPERATION
5.4.1 Filter Operation (cont.)
8. Begin the filtering process by pulling the
yellow handle to open the oil-return valve
(this activates the filter pump automatically).
Begin the filtering process by pulling yellow handle
to open oil return valve. Leave the drain valve
(red handle) open during the filtering process.
9. Oil will begin to pump from the filter pan
into the frypot. Allow the oil to circulate
through the frypot for the remainder of the
timed
countdown
(approximately
10
minutes).
This process is known as
"polishing".
Polishing the oil removes suspended particles,
which increases the life of the oil.
10. The computer will display FILL at the end
of the timed countdown. Replace the frypot
grid rack. Close the red drain valve handle to
begin refilling the frypot.
When the computer displays FILL, close the
drain valve to begin refilling the frypot.
5-8
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 5: FILTRATION OPERATION
5.4.1 Filter Operation (cont.)
11. After all shortening is pumped back into the
frypot, bubbles will form, indicating air in the
oil return lines. Allow the shortening to
bubble for 15-30 seconds to ensure all
shortening is cleared from the return lines.
An audible alarm will sound, indicating that
the frypot is full. Push the yellow handle to
close the oil return valve and deactivate the
filter pump.
Allow the oil to bubble for 15-30 seconds to
ensure evacuation of all oil in the return lines.
12. If the shortening level is low, add fresh
shortening until the level is at the top OIL
LEVEL line (the shortening is at operating
temperature).
Add fresh shortening until the level is at the top
OIL LEVEL line.
DO NOT OVERFILL THE
FRYPOT.
13. Do not allow crumbs to accumulate in the
crumb tray. The crumb tray MUST be
emptied into a fireproof container at the end
of frying operations EACH day.
Empty the filter pan crumb tray into a fire-proof
container at the end of frying operations each day.
DO NOT ALLOW CRUMBS TO ACCUMULATE IN
TRAY.
5-9
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 5: FILTRATION OPERATION
5.4.1 Filter Operation (cont.)
14. OPTIONAL EQUIPMENT: Drain-flushes
are included on 5-battery and larger
Frymaster FPD65 Series fryers.
After
filtering frypot farthest from the filter system
for 10 minutes, close the oil return valve to
stop the filtering process. Do not refill the
frypot. Close the drain valve (red handle) on
the frypot being filtered. Ensure all other
valves (red and yellow handles) are closed.
Pull the blue handle to open the flush valve
(6-battery systems have two). After the drain
line is clear of sediment (approximately 2
minutes), push the blue handle to close flush
valve. Open the oil-return valve (yellow
handle) to refill the frypot.
Left drain-flush handle location (arrow) for frypot
#6.
15. OPTIONAL EQUIPMENT: Shortening
Disposal: Follow store procedures when
disposing of spent shortening. Ensure the
Shortening Disposal System is properly
connected and working properly before
proceeding. Turn the blue handle on the
wand/dispose valve to "DISPOSE" to start
the disposal process. Turn the blue handle to
"OFF" when the disposal process for that
frypot is complete.
Blue handle in "DISPOSE" position. Turn handle
to "OFF" after spent shortening is disposed of.
DANGER
The crumb tray in fryers equipped with a filter system must be emptied into a
fireproof container at the end of frying operations each day. Some food particles
can spontaneously combust if left soaking in certain shortening material.
WARNING
Do not bang fry baskets or other utensils on the fryer’s joiner strip. The strip is
present to seal the joint between the frypots. Banging fry baskets on the strip to
dislodge shortening will distort the strip, adversely affecting its fit. It is designed for
a tight fit and should only be removed for cleaning.
5-10
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 6: PREVENTATIVE MAINTENANCE
6.1 General
DANGER
Never attempt to clean the fryer during the cooking process or when the frypot is
filled with hot oil/shortening. If water comes in contact with oil/shortening heated to
cooking temperature, it will cause spattering of the oil/shortening, which can result
in severe burns to nearby personnel.
Any equipment works better and lasts longer when maintained properly and kept clean. Cooking
equipment is no exception. Frymaster FPD65 Series gas fryers should be kept clean during the
working day, and thoroughly cleaned at the end of each day. Below are recommendations for daily,
weekly and periodic preventative maintenance.
6.1.1 Daily
WARNING
Use a commercial grade cleaner formulated to effectively clean and sanitize foodcontact surfaces. Read the directions and precautionary statements for use.
Particular attention must be paid to the concentration of cleaner and the length of
time the cleaner remains on the food-contact surfaces.
A. Remove and wash all removable parts.
B. Clean all exterior surfaces of the cabinet. Do not use cleaners, steel wool, or any other
abrasive material on stainless steel.
C. Filter the cooking oil and replace if necessary. The oil should be filtered more frequently
when under heavy use.
D. Clean filter pan, as well as, crumb tray as discussed on page 5-9.
6.1.2 Weekly
A. Completely drain the oil from the fryer into a metal stockpot of sufficient size to safely hold
the entire contents of the frypot for disposal. Do not use a glass or plastic container.
B. Clean the frypot by following boil-out procedures in Chapter 4.2.
WARNING
Never allow water to boil down and expose the heating tubes. Frypot damage will
result.
6-1
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 6: PREVENTATIVE MAINTENANCE
6.1.3 Periodic/ Annual
The fryer should be inspected and adjusted periodically by qualified service personnel as part
of a regular kitchen maintenance program.
Frymaster/Dean recommends that the fryer be inspected at least annually by a Factory
Authorized Service Technician as follows:
•
Inspect fryer cabinet inside and out, front and rear, for excessive oil build-up and/or oil
migration. Verify that burners and associated components (i.e. gas valves, pilot assemblies,
ignitors, etc.) are in good condition and functioning properly. Inspect all gas connections for
leaks and ensure all connections are properly tightened.
•
Verify that temperature and high-limit probes are properly connected, tightened and functioning
properly.
•
Verify all component box components (i.e. computer/controller, relays, transformers, interface
boards, etc.) are in good condition and free from oil migration build-up and other debris. Inspect
component box wiring and ensure all connections are tight and all wiring is in good condition.
Ensure all safety features (i.e. drain safety switches, reset switches, etc.) are present and
functioning properly.
•
Verify that frypot is in good condition and free of leaks. Verify that frypot tube diffusers are
present and in good condition (i.e. no visible deterioration or damage).
•
Verify that all wiring and connections are tight and in good condition.
Built-in Filtration:
•
Inspect all oil-return and drain lines for leaks and verify that all connections are tight.
•
Inspect the filter pan for leaks and cleanliness. If there is a large accumulation of crumbs in the
crumb basket, advise the owner/operator that the crumb basket should be emptied into a fireproof
container and cleaned daily.
•
Verify that all O-rings and seals (including those on quick-disconnect fittings) are present and in
good condition. Replace O-rings and seals if worn or damaged.
6-2
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 6: PREVENTATIVE MAINTENANCE
6.1.3 Periodic/ Annual (cont.)
•
Check filtration system integrity as follows:
− With the filter pan empty, place each oil return handle, one at a time, in the "ON" position.
Verify that the pump activates and that bubbles appear in the cooking oil/shortening of the
associated frypot.
− Close all oil return valves (i.e., place all oil return handles in the "OFF" position). Verify proper
functioning of each oil return valve by activating the filter pump using the lever on one of the oil
return handle microswitches. No air bubbles should be visible in any frypot.
− Verify that the filter pan is properly prepared for filtering, then drain a frypot of oil heated to
350°F (177°C) into the filter pan and close the frypot drain valve. Place the oil return handle in
the "ON" position. Allow all cooking oil/shortening to return to the frypot (indicated by bubbles
in the cooking oil/shortening. Return the oil return handle to the "OFF" position. The frypot
should refill in no more than 2 minutes and 30 seconds.
To ensure good fryer health and a safe environment, the fryer should be checked and adjusted
periodically by qualified service personnel as part of a regular kitchen maintenance program.
6.1.4 Stainless Steel Care
DANGER
DO NOT let water splash into the tank of hot oil. It will splatter and can cause severe
burns.
All stainless steel fryer cabinet parts should be wiped regularly with hot, soapy water during the day,
and with a liquid cleanser designed for stainless steel at the end of each day.
A. Do not use steel wool, abrasive cloths, cleansers or powders.
B. Do not use a metal knife, spatula or any other metal tool to scrape stainless steel! Scratches
are almost impossible to remove.
C. If it is necessary to scrape the stainless steel to remove any encrusted materials, soak the area
first to soften the deposit, then use a wood or nylon scraper only.
6-3
THIS PAGE INTENTIONALLY LEFT BLANK.
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 7: TROUBLESHOOTING
7.1 General
DANGER
Hot cooking oil/shortening will cause severe burns. Never attempt to move this
appliance when filled with hot cooking oil/shortening or to transfer hot cooking
oil/shortening from one container to another.
DANGER
This equipment should be unplugged when servicing, except when electrical circuit
tests are required. Use extreme care when performing such tests.
This appliance may have more than one electrical power supply connection point.
Disconnect all power cords before servicing.
Inspection, testing and repair of electrical components should be performed by an
authorized service agent only.
The problems and possible solutions covered are those most commonly encountered. To
troubleshoot, perform the test set-up at the beginning of each condition. Follow each step in
sequence.
7.2 Pilot Burner Malfunction
A. Pilot will not ignite; no evidence of gas at pilot burner.
1. Check that gas valve is open and gas is present at the gas valve.
2. Check pilot burner orifice for dirt or lint.
3. Authorized Service Agent Only: Remove pilot burner gas-supply line and check for
contamination; blow out if necessary, then reinstall.
B. Pilot burner ignites but will not remain lit when gas valve manual knob is released.
1. Check that thermopile lead is properly connected at the terminal block on the gas valve.
2. Authorized Service Agent Only: Pilot flame may be too high or too low. Adjust pilot
flame adjustment screw so that pilot flame extends about 3/4-inch (19-mm) above the top
of the pilot burner.
7-1
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 7: TROUBLESHOOTING
7.2 Pilot Burner Malfunction (cont.)
3. Check all connections for cleanliness and security.
C. Pilot flame of proper size, but is unstable.
thermopile completely at all times.
Flame wavers and does not envelop the
1. Check for drafts that might be caused by air conditioning equipment or make-up air
apparatus. Turn air-moving equipment off and recheck the pilot.
7.3
Main Burner Malfunctions
A. Main burner will not come "ON"; gas not detected at main burner.
1.
Check that the gas valve is open.
2.
Check that the pilot is ignited and is operating properly.
3.
Authorized Service Agent Only: Check the high-limit switch for continuity.
4.
Authorized Service Agent Only: Check the combination gas valve and replace if
defective.
B. Main burner flames are small and appear lazy; shortening does not come up to temperature
quickly.
1.
Authorized Service Agent Only: Check gas pressure at the pressure tap of the gas valve.
Use dial type or standard water-type U-gauge manometer. With burner in operation, the
pressure should be 4" W.C. (10 mbar) for natural gas, and 11" W.C. (27.5 mbar) for
propane. If not, remove the pressure regulator adjustment cover. Use screwdriver to
turn the adjusting screw for proper pressure. Replace cover, re-check pressure and reinstall pressure tap plug.
C. Signs of excessive temperature; shortening scorches and quickly becomes discolored.
1.
Check operating thermostat. May be out of adjustment or calibration. Recalibrate if
necessary.
2.
Check gas pressure as outlined above.
3.
Shortening used is of inferior quality and/or shortening has been used too long. Replace
shortening.
4.
Ensure frypot is clean when refilling with new shortening.
7-2
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 7: TROUBLESHOOTING
7.3
Main Burner Malfunctions (cont.)
D. Fryer will not reach the temperature setting and/or runs erratically.
1.
Incorrect location of sensor probe or defective temperature sensor.
2.
Loose wiring/wire connection
E. Fryer shortening temperature cannot be controlled; fryer runs at high-limit temperature.
1.
Defective temperature probe; Call Authorized Service Agent.
7-3
FUSE
BLU
BLU
GND
WHT
WHT
BLK
FUSE
WHT
BLK
WHT
LINE VOLTAGE
7-4
1
2
SPEAKER
1
2
RED
BLU
J3
TO J2 COMPUTER INTERFACE BOARD
1
2
TO CM4-S COMPUTER
CM4-S COMPUTER
1 2 3 4 5 6 7 8 9
1 2 3 4 5 6 7 8 9
BLU
1
2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
HI LIMIT
BLU
24 VAC
GAS
VALVE
IGNITER
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
J2
BLK
BLK
BLK
YEL
COMPUTER INTERFACE
BOARD
1 2 3 4 5 6 7 8 9 10 11 12
1 2 3 4 5 6 7 8 9 10 11 12
RED
YEL
RED
SOUND
GRD
A
BLK
WHT
12V
LINE
YEL
BLU
RED
24V
LINE
WHT
YEL
BLK
TRANSFORMER
SENSOR
HI TENSION
PV
MV
MV/PV
CND
IGN
TR
SEN
TH
C
8051481A
NO
NC
SAFETY
DRAIN SWITCH
BLU
BRN
WHT
WHT
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 7: TROUBLESHOOTING
7.4 Wiring Diagram, Main
7-5
BLK
CB
30C
WHT
P1
41C
MOTOR
82C
12C
8C
27C
FOR CHANGE OF ROTATION INTERCHANGE
LEADS T5 AND T8 ON THE MOTOR
P1
P2
T3
T2
P2
T8
T3
T2
T4
T8
T5
T4
LOW VOLTAGE SHOWN
24V
120V
T5
HIGH VOLTAGE SHOWN
5 AMP-480V
CIRCUIT BREAKER
7 AMP-120V
WHT#1
BLK
INPUT
115V
CIRCUIT
COM
82C
33C
NC
NO
2
4
OIL RETURN
LH ADD-0N(S)
86C
1
3
OIL RETURN
TRANSFORMER/RELAY ASSY
NC
NO
33C
MICRO SWITCH
SHOWN IN
OFF POSITION
OIL RETURN
FRYER
COM
35C
31C
NC
NO
OIL RETURN
RH ADD-ON(S)
COM
35C
BY-PASS SWITCH
9C
8051428A
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 7: TROUBLESHOOTING
7.5 Wiring Diagram, Filter
THIS PAGE INTENTIONALLY LEFT BLANK.
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 8: PARTS LIST
8.1 Cabinetry and Related Components
8-1
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 8: PARTS LIST
8.1 Cabinetry and Related Components (cont.)
ITEM
1
2
3
4
5
6
*
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
*
*
23
24
25
* Not Illustrated
PART #
810-0357
810-0356
823-3248
202-1182
201-1182
200-1463
200-2493
200-1198
823-3352
200-1493
200-1611
200-4241
200-2308
200-1393
200-1471
202-1299
201-4775
202-4775
201-4237
202-4237
201-1299
823-3826
200-3696
200-3694
200-1376
200-1425
200-4238
210-3700
COMPONENT
Caster, 5" Swivel – With Brake
Caster, 5" Swivel – Without Brake
Support, Caster- Channel Base
Gusset, Side Panel- Left
Gusset, Side Panel- Right
Channel, Base- Front & Rear- 2-Battery (FPD565 & FPD665)
Channel, Base- Front & Rear- 1-Battery (FPD565 Only)
Channel, Base- UFF Filter
Support, Caster- UFF Base
Frame, Base Lower Plate- UFF
Base, Upper- UFF
Plate, Motor Support- Offset
Post, Door- UFF Cabinet
Channel, Lower Joiner
Duct, Door Access
Panel, Side- Painted- Right
Panel, Inner- Left
Panel, Inner- Right
Panel, Inner UFF- Left
Panel, Inner UFF- Right
Panel, Side- Painted- Left
Fluecap
Back, Upper Structural (FPD665)
Back, Upper Structural (FPD565)
Bracket, Restraining
Back, Lower Structural- Right & Left Cabinet
Back, Lower Structural- Middle UFF Cabinet
Hanger, Basket- 2-Battery
8-2
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 8: PARTS LIST
8.2 Doors, Topcaps and Related Components
8-3
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 8: PARTS LIST
8.3 Frypots, Burners and Related Components
8-4
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 8: PARTS LIST
8.3 Frypots, Burners and Related Components (cont.)
ITEM
1
2
3
4
5
*
*
6
7
8
9
10
11
12
13
*
14
15
*
16
17
18
19
20
21
*
*
22
23
*
24
*
*
25
*
26
*
27
28
*
*
*
*
29
30
* Not Illustrated
PART #
823-3948
210-5170
810-2150
810-2149
810-2151
200-2738
200-2746
200-1615
809-0822
809-0823
810-2138
813-0642
813-0705
813-0643
810-2050
810-2324
823-3617
807-3628
807-3552
813-0174
813-0635
813-0066
813-0743
813-0165
813-0670
813-0585
813-0737
810-2043
809-0805
200-1450
807-1553
807-1311
807-1310
810-0703
810-0705
810-2155
810-2032
812-1544
106-2634SP
200-4086
200-4087
200-4088
200-3649
810-2524
106-2897SP
COMPONENT
Frypot- S/S- 65 Series
Diffuser, Burner Tube
Burner, Right
Burner, Center
Burner, Left
Bracket, Burner Mounting
Shield, Burner Heat
Bracket, Manifold Mounting
Bolt, ¼-20 x ½" Hex Head
Nut, Nylock- ¼-20
Valve, Trailing Pilot
Tee, 1/8" NPT
Plug, Brass- 1/8" Square Head
Nipple, 1/8" NPT x Close BM
Orifice, Natural- #44 (2.18 mm)
Orifice, LP- #53 (1.40 mm)
Manifold, Gas
Valve, Gas- LP-24V, Honeywell
Valve, Gas- Natural-24V, Honeywell
Union- ¾" NPT BM
Nipple, ¾ NPT x 2-½" BM
Elbow- ¾" NPT 90° BM
Nipple, ¾ NPT x 3-½" BM
Elbow, Street- ½" NPT 90° BM
Nipple, ½ NPT x 19" BM (Measure To Confirm Length)
Nipple, ½ NPT x 20-½" BM (Measure To Confirm Length)
Nipple, ½ NPT x 21" BM (Measure To Confirm Length)
Clamp, Pipe- ½"
Bolt, Pipe Clamp- ¼-20 x ½" Hex
Bracket, Gas-Supply Clamp Support (UFF-Equipped Systems)
Burner, Pilot- LP- Electronic Ignition
Burner, Pilot- Natural- Electronic Ignition
Sensor, Flame
Gas Line, Main Pilot Supply- ¼ x 17-½"
Gas Line, Main Pilot Supply- ¼ x 23"
Burner, Trailing Pilot- LP
Burner, Trailing Pilot- Natural
Gas Line, Trailing Pilot Supply- ¼ x 12" (Not For Main Pilot)
Flue Assembly, Complete
Shield, Flue Heat
Front, Flue Box
Rear, Flue Box
Deflector, Flue
Grid, Frypot- 65 Series
Cover, Frypot- 65 Series
8-5
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 8: PARTS LIST
8.4 Component Box Components
3
15
17
14
4
6
1
16
7
8
5
12
11
10
9
13
2
CM4-S
18
ITEM
1
2
3
4
5
*
6
7
8
9
10
*
11
12
*
13
14
15
16
17
18
*
* Not Illustrated
PART #
823-3242
210-1364
200-1322
200-1326
807-3563
807-1315
806-4549
807-0833
807-0855
807-0800
807-1321
807-3750
807-3580
807-3577
807-3538
807-3680
806-7179
200-2052
807-3611
106-1541SP
806-8305
106-3028
823-3433
COMPONENT
Control Box (Inside Non-Filter Fryer Cabinets)
Plate, Face (For Item #1)
Bracket, Spark Module
Cover, Spark Module
Module, Ignition (Spark)
Cable, Ignition Module
Board, Interface
Relay, 12VDC 5A 1PDT (Latching)
Transformer, 120VAC 50/60 Hz -12V 20VA
Transformer, 120VAC 50/60 Hz -24V 50VA
Fuse Holder, Buss
Fuse, 5A
Switch, Rocker- Manual Filter Power
Breaker, Circuit- 7-Amp (115VAC Circuits)
Breaker, Circuit- 5-Amp (230VAC Circuits)
High-Limit Thermostat- Manual Reset 450° F (Non-CE Only)
Device, Sound
Bracket, Sound Device
Relay, Filter- 24VAC Coil 24A
Probe, Temperature- Computer
Computer, CM4-S- With Bezel Generic (Segmented Programming)
Computer, CM4-S- With Bezel Church’s Only (Segmented. Prog.)
Bezel, Computer
8-6
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 8: PARTS LIST
8.5 Filter Pan and Related Components
8-7
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 8: PARTS LIST
8.6 Oil-Drain Components
8-8
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 8: PARTS LIST
8.6 Oil-Drain Components (cont.)
ITEM
1
*
2
3
4
5
6
7
8
9
10
11
12
13
14
PART #
823-4189
823-3441
813-0829
809-0884
816-0544
200-1840
813-0749
813-0165
810-1069
810-1057
810-1668
813-0062
813-0096
813-0686
813-0784
15
16
17
18
*
*
*
*
19
20
21
22
23
* Not Illustrated
106-1401
200-1617
210-2029
200-1940
823-3440
809-0885
809-0843
816-0547
807-2104
809-0842
816-0220
200-1257
810-2127
COMPONENT
Pipe, Drain- Right- D665 (With Oil Disposal System)
Pipe, Drain- Right- D565 (No Oil-Disposal System)
Elbow, Drain Pipe- 75°
Nut, Slip Joint- 1-½"
O-ring (Slip-Joint Nut)
Drain Manifold Tube
Tee, 1-½" NPT With Handle
Elbow, Street- ½ x ½" 90°
Flex Line, 5/8" x 29-½ " (Measure To Confirm Length)
Flex Line, 5/8 x 13" (Measure To Confirm Length)
Adapter, 5/8" O.D. x ½"- Male (Use With 810-1057 and 810-1069)
Elbow, ½" NPT BM 90°
Nipple, ½ x 6" NPT BM
Bell Reducer, 1-½ x ½" NPT
Drain Pipe, Left Side
Drain Valve Components
Bracket, Microswitch (Optional On Some Units)
Washer, Drain Valve (Use Without Microswitch)
Bracket, Activator- Microswitch
Handle (Actuator), Drain Valve
Handle, Push/Pull- Drain (With Cap)
Washer, 3/8 x 1 x .083"
Cotter Pin
Cap, Vinyl-Red
Microswitch (Optional On Some Units)
Nut, Nylock- #4-40 (Microswitch To Bracket)
Insulation, Microswitch
Retainer, Nut
Drain Valve, 1-½" Full Port (With Washers & Nut)
8-9
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 8: PARTS LIST
8.7 Oil-Return Components
1
Oil Disposal Plumbing
(Optional)
8-10
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 8: PARTS LIST
8.7 Oil-Return Components (cont.)
ITEM
3
4
5
6
7
8
*
*
*
9
10
*
*
*
*
11
PART #
813-0173
813-0003
813-0165
813-0051
813-0062
810-1003
823-4234
210-4239
816-0549
106-1837SP
810-0278
823-3187
816-0548
823-4174
809-0885
813-0463
12
13
14
15
*
*
16
17
* Not Illustrated
810-1056
823-3996
810-0487
810-1669
810-0278
816-0549
810-2098
810-2100
COMPONENT
Union, ½" NPT BM
Tee, ½" NPT BM
Elbow, Street ½" NPT BM 90°
Coupling, ½" NPT BM
Elbow, ½" NPT BM 90°
Valve, Ball- Three-Way ½" 180°
Handle, Wand/Disposal
Bracket, Wand/Disposal Handle
Cap, Handle- Blue (Cut Length To Fit)
Disconnect Assembly, With Collar
Valve, Ball- Oil-Return ½"
Handle, Oil-Return Valve
Cap, Oil-Return Handle- Yellow
Handle Assembly (Actuator)- Oil-Return Valve
Washer, Actuator- Ball Valve- 3/8 x 1 x 0.083"
Plug, Counter-Sink Hex ½"
Oil Disposal Components
Flexline, Oil Disposal- 5/8 x 52-½"
Nipple Assembly, Oil Disposal
Disconnect, Male- Oil Disposal
Adapter, Female- 5/8 x ½"
Handle, Oil-Return Flush Valve
Cap, Flush Valve Handle- Blue
Pump, Filter- 8GPM
Motor, Filter Pump- 120/230VAC 1/3 HP
8.8 Suction Tube, Oil-Return Components
1
8-11
FRYMASTER FPD65 SERIES GAS FRYERS
CHAPTER 8: PARTS LIST
8.8 Suction Tube, Oil-Return Components (cont.)
ITEM
1
*
2
3
4
5
6
7
8
PART #
810-0697
826-1392
813-0608
823-3188
813-0062
813-0093
813-0173
813-0165
813-0022
813-0156
813-0003
COMPONENT
Disconnect, Male- Suction Tube
O-ring, Suction Tube Connection (Qty: 5)
Coupling, Full- ½" NPT BM
Suction Manifold Assembly
Elbow, ½" x 90° NPT BM
Nipple, ½ NPT x 4" NPT BM
Union, ½" NPT BM
Elbow, Street- ½" x 90° NPT BM
Oil Suction Start Fitting
Nipple- ½" NPT x Close BM
Plug, ½" NPT BM Hex Head
Tee, ½" NPT BM
* Not Illustrated
8-12
THIS PAGE INTENTIONALLY LEFT BLANK.
Frymaster, 8700 Line Avenue, PO Box 51000, Shreveport, Louisiana 71135-1000
Shipping Address: 8700 Line Avenue, Shreveport, Louisiana 71106
TEL 1-318-865-1711
PRINTED IN THE UNITED STATES
FAX (Parts) 1-318-688-2200
SERVICE HOTLINE
1-800-551-8633
FAX (Tech Support) 1-318-219-7135
819-6039
JANUARY 2004
Download PDF

advertising