Fuel Fitness FT94 Treadmill User Manual

FT94
OWNER’S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR NEW TREADMILL!
Table of Contents
Product Registration
...2
Important Safety Instructions
3
Important Electrical Information
.4
Important Operation Instructions
5
Assembly instructions
..6
Folding Instructions
.11
Operation of Your New Treadmill
.12
Programmable Features
.16
General Maintenance.
17
Service Checklist - Diagnosis Guide
.20
Manufacturer s Limited Warranty
...
-1-
21
FT94
CONGRATULATIONS ON YOUR
NEW TREADMILL AND WELCOME
TO THE SOLE FAMILY!
Thank you for your purchase of this quality treadmill from FUEL. Your new treadmill
has been manufactured by one of the leading fitness manufacturers in the world and
is backed by one of the most comprehensive warranties available. FUEL will do all
we can to make your ownership experience as pleasant as possible for many years
to come.
If you have a problem that requires service, call FUEL at: 866-545-3835,or send an
email to: service@fuelfitnessusa.com
Please take a moment at this time to record below the name of the dealer, their
telephone number, and the date of purchase for easy contact in the future. We
appreciate your confidence in FUEL and we will always remember that you are the
reason that we are in business. Please complete and mail your registration card
today and enjoy your new treadmill.
Yours in Health,
FUEL Fitness
Name of Dealer______________________________________
Telephone Number of Dealer___________________________
Purchase Date_______________________________________
Product Registration
RECORD YOUR SERIAL NUMBER
Please record the Serial Number of this fitness product in the space provided below.
Serial Number_______________________________________
REGISTER YOUR PURCHASE
The self-addressed product registration card must be completed in full and returned to FUEL, or
to register online go to: www.fuelfitnessusa.com
FT94 / 2008 ver.B
-2-
FT94
Important Safety Instructions
WARNING - Read all instructions before using this appliance.
DANGER - To reduce the risk of electric shock disconnect your FUEL treadmill from the
electrical outlet prior to cleaning and/or service work.
WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install
the treadmill on a flat level surface with access to a 120-volt, 15-amp grounded outlet with
only the treadmill plugged into the circuit..
DO NOT USE AN EXTENSION CORD UNLESS IT IS 14AWG OR BETTER, WITH ONLY ONE
OUTLET ON THE END. The treadmill should be the only appliance in the electrical circuit.
DO NOT ATTEMPT TO DISABLE THE GROUNDED PLUG BY USING IMPROPER
ADAPTERS, OR IN ANY WAY MODIFY THE CORD SET. A serious shock or fire hazard may
result along with computer malfunctions.
Do not operate treadmill on deeply padded, plush or shag carpet. Damage to both carpet and
treadmill may result.
Do not block the rear of the treadmill. Provide a minimum of 3 1/2 feet clearance between the
rear of the treadmill and any fixed object.
Keep children away from the treadmill. There are obvious pinch points and other caution
areas that can cause harm.
Keep hands away from all moving parts.
Never operate the treadmill if it has a damaged cord or plug. If the treadmill is not working
properly, call your dealer.
Keep the cord away from heated surfaces.
Do not operate where aerosol spray products are being used or where oxygen is being
administered. Sparks from the motor may ignite a highly gaseous environment.
Never drop or insert any object into any openings.
Do not use outdoors.
To disconnect, turn all controls to the off position, remove tether cord, then remove the
plug from the outlet.
Do not attempt to use your treadmill for any purpose other than for the purpose it is
intended.
The pulse sensors are not medical devices. Various factors, including the user s movement,
may affect the accuracy of heart rate readings. The pulse sensors are intended only as
exercise aids in determining heart rate trends in general.
Use handrails provided; they are for your safety.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use on
your treadmill. Quality athletic shoes are recommended to avoid leg fatigue.
Remove tether cord after use to prevent unauthorized treadmill operation. SAVE
THESE INSTRUCTIONS - THINK SAFETY!
-3-
FT94
Important Electrical Information
WARNING!
NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. Large
switching currents of the drive motor will trip GFCI type outlets, as with any appliance with a
large motor. Route the power cord away from any moving part of the treadmill including the
elevation mechanism and transport wheels.
NEVER remove any cover without first disconnecting AC power.
If voltage varies by ten percent (10%) or more, the performance of your treadmill may be
affected. Such conditions are not covered under your warranty. If you suspect the voltage
is low, contact your local power company or a licensed electrician for proper testing.
NEVER expose this treadmill to rain or moisture. This product is NOT designed for use outdoors,
near a pool or spa, or in any other high humidity environment. The operating environmental
specification is 40 to 120 degrees Fahrenheit, and humidity limit is 95%, non-condensing (no
water drops forming on surfaces).
Grounding Instructions
This product must be grounded. If the treadmill should malfunction or breakdown, grounding
provides a path of least resistance for electric current, reducing the risk of electric shock. This
product is equipped with a cord having an equipment-grounding plug. The plug must be plugged
into an appropriate outlet that is properly installed and grounded in accordance with all local
codes and ordinances.
DANGER - Improper connection of the equipment-grounding conductor can result in a
risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt
as to whether the product is properly grounded. Do not modify the plug provided with the
product if it will not fit the outlet; have a proper outlet installed by a qualified electrician.
This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the
plug illustrated below. A temporary adapter that looks like the adapter illustrated below may be
used to connect this plug to a 2-pole receptacle as shown below if a properly grounded outlet is
not available. The temporary adapter should be used only until a properly grounded outlet,
(shown below) can be installed by a qualified electrician. The green colored rigid ear-lug, or the
like, extending from the adapter, must be connected to a permanent ground such as a properly
grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal
screw.
Adapter
Grounded Outlet
Metal Screw
Grounding Pin
Tab of
Grounding
Screw
Grounded Outlet Box
-4-
FT94
Important Operation Instructions
NEVER operate this treadmill without reading and completely understanding the results of any
operational change you request from the computer.
Understand that changes in speed and incline do not occur immediately. Set your desired
speed on the computer console and release the adjustment key. The computer will obey the
command gradually.
NEVER use your treadmill during an electrical storm. Surges may occur in your household
power supply that could damage treadmill components.
Use caution while participating in other activities while walking on your treadmill; such as
watching television, reading, etc. These distractions may cause you to lose balance or stray
from walking in the center of the belt; which may result in serious injury.
NEVER mount or dismount the treadmill while the belt is moving. FUEL treadmills start at a very
low speed and it is unnecessary to straddle the belt during start up. Simply standing on the belt
during slow acceleration is proper after you have learned to operate the unit.
Always hold on to a handrail or hand bar while making control changes (incline, speed, etc.).
Do not use excessive pressure on console control keys. They are precision set to function
properly with little finger pressure. Pushing harder is not going to make the unit go faster or
slower. If you feel the buttons are not functioning properly with normal pressure contact your
FUEL dealer.
Safety Tether Cord
A safety tether cord is provided with this unit. It is a simple magnetic design that should be used
at all times. It is for your safety should you fall or move too far back on the tread-belt.
Pulling this safety tether cord will stop tread-belt movement.
To Use:
1. Place the magnet into position on the console control head. Your treadmill will not start and
operate without this. Removing the magnet also secures the treadmill from unauthorized use.
2. Fasten the plastic clip onto your clothing securely to assure good holding power. Note: The
magnet has strong enough power to minimize accidental, unexpected stopping. The clip should
be attached securely to make certain it does not come off. Be familiar with its function and
limitations. The treadmill will stop, depending on speed, with a one to two step coast anytime the
magnet is pulled off the console. Use the red Stop / Pause switch in normal operation.
-5-
FT94
Assembly Instructions (FT94)
!!ATTENTION: IMPORTANT UNPACKING INSTRUCTIONS. PLEASE
READ BEFORE UNPACKING YOUR FOLDING TREADMILL!!
Serious injury could occur if this folding treadmill is not unpacked properly.
There is a Velcro strap installed around the treadmill base that prevents the treadmill from unfolding
accidentally during shipping. If this strap is not removed properly the treadmill could spring open
unexpectedly and cause injury if someone is standing near the treadmill when the strap is removed.
To ensure your personal safety during removal of the shipping strap please make sure the treadmill
is positioned flat on the ground, in the orientation it would be in if you were using the treadmill. Do
not turn the treadmill up on its side while removing the shipping strap. This could cause the
treadmill’s folding mechanism to spring open. If the end of the Velcro strap (that you need to grab to
remove it) happens to be under the treadmill deck, reach under the deck to grab it, but do not tilt the
treadmill up to gain access to the strap end.
-6-
FT94
ASSEMBLY PACK CHECK LIST
#96. M5 x 10 m/m
#95. 5/16 x19x1.5T
Phillips Head Screw (6pcs)
Curved Washer (8pcs)
#94. 5/16 x15m/m
#90. 3.5x12 m/m
Self Tapping Screw (4pcs)
Button Head Socket Bolt
(14pcs)
#93.Lubricant (1pc)
#102. Safety Key
(1pc)
#98. M6 Allen Wrench (1pc)
#97. Combination M5 Allen
Wrench
& Phillips Head Screw Driver(1 pc)
-7-
FT94
Step 1.
Remove the treadmill from the carton and lay it aside on a smooth level surface.
Step 2.
Connect the Lower Computer Cable (38) with the Middle Computer Cable (37).
37
38
Step 3.
Insert the Upright tubes (4,5) into the Frame Base with the eight 5/16 x15mm Button Head
Socket Bolts (94) and four 5/16" x 19 x 1.5T Curved Washers (95) - on the bolts for the side of
the tubes - using the M5 Allen Wrench (97). Be careful not to pinch the computer cable while
installing the right Upright tube.
95
94
94
94
94
97
95
-8-
FT94
Step 4.
Install the Left Handrail Cover (41) onto the Left Upright tube (4), Right Handrail Cover (40) onto
the Right Upright tube (5). Make sure they are facing the correct direction and allow them to slide
down and sit at the bottom of the tubes.
40
41
4
5
Step 5.
Connect the middle Computer Cable (37) with the upper Computer Cable (36).
36
37
Step 6.
Install the Console Assembly (39) into the Upright tubes (4,5) with the six 5/16 x15mm Button
Head Socket Bolts (94) and four 5/16" x 19 x 1.5T Curved Washers (95) using the M5 Allen
Wrench (97). The two bolts in the front do not require washers.
39
95
94
97
94
95
94
94
5
95
4
-9-
FT94
Step 7.
Install the Left and Right Handrail Covers (41, 40) onto the Console Assembly (39) with the four
3.5x12mm Self Tapping Screws (90).
39
40
41
90
97
90
Step 8
Install the Frame Base Caps (44,43) onto the Frame Base with six M5x10mm Phillips Head
Screws (96).
43
96
44
97
96
Please Ensure All Screws are tightened After All Components Assembly Complete.
-10-
FT94
Folding Instructions
Do not attempt to move the unit unless it is in the folded and locked position. Be sure the power
cord is secured to avoid possible damage. Use both handrails to maneuver the unit to the
desired position.
UNFOLDING
Hold the treadmill running board with your left hand. Pull the locking knob with your right hand
and slowly lower the treadmill running board.
FOLDING
Ensure the incline angle of the treadmill is at its lowest position. Lift the treadmill running board up
until locking knob pops into the hole in the telescoping tube.
-11-
FT94
W
Operation of Your Treadmill
Getting familiar with the control panel
FT94 Console
Initial Display:
When the power is turned on, the main display will light up showing all characters. The console
will be performing an internal test to make sure the console is operational. The display will then
scroll through three numbers, the first showing the current software version, second is how many
hours the treadmill has been in use and third is how many virtual miles the treadmill has gone.
The treadmill will then enter idle mode and show P0 on the display, which is the starting point for
operation.
-12-
FT94
WINDOW DISPLAY DATA:
SCAN:
SPEED:
When lit, will scan through all the display information; each one for 5 seconds.
Displays the current belt speed from starting at 1.0Mph to 10.0Mph.
TIME:
Accumulates total workout time from 00:00 to 99:59.
DISTANCE:
Accumulates total workout distance from 0.00 to 99.99 miles.
CALORIES: Accumulates the user s calorie consumption during exercise. Max. Value is 9999
calories.
PULSE:
Displays your current heart rate in beats per minute from 40 to 240.
♥ Icon:
The heart icon blinks when a pulse is detected.
INCLINE LED:
When lit, the display will be showing the elevation position from 0 to 10.
LUBE LED:
Reminds the user to apply silicon lubricant between the belt and deck. To turn
off the light press and hold the SELECT button for 5 seconds.
FUNCTION BUTTON:
START:
STOP:
Press START button to start training.
Press STOP button to stop training and press for 3 seconds to reset.
FAST:
Press FAST button to increase your speed.
SLOW:
Press SLOW button to decrease your speed.
UP:
DOWN:
Press UP button to increase elevation position.
Press DOWN button to decrease elevation position.
ENTER:
Press ENTER button to select different setting parameters in STOP mode.
SELECT:
Press SELECT button to scroll through the display workout information.
PROGRAM UP/DOWN: Press PROGRAMUP/DOWN buttons to scroll through workout programs.
RAPID SPEED KEYS:
10 preset speed buttons to jump to a desired speed quickly. You can also
press the any of the 10 buttons to start treadmill from the start-up screen.
The treadmill will automatically start and slowly increase speed to the
RAPID INCLINE KEYS:
preset number.
10 preset incline buttons to jump to a desired incline setting quickly.
Quick-Start Operation:
STEP 1: Attach the Safety key to wake display up (if not already on). The main window will
show the initial display: P0.
STEP 2: Press the START button to begin belt movement after a three second count down. Use
the FAST/SLOW keys to adjust the desired speed (on console) at any time during
training. Using the UP/DOWN keys to adjust the Incline at any time during training. To
-13-
FT94
set the time to count down, see STEP 7.
STEP 3: Press the SELECT button to scroll through your workout data. The initial screen will
be showing the SPEED. Pressing the SELECT button will show the TIME then
DISTANCE, CALORIES, PULSE, INCLINE and SCAN. In scan mode each data will
be displayed for 5 seconds.
STEP 4: To get a pulse reading, simply grasp both stainless steel pick-ups. Make sure the
display is set to show Pulse, or Scan. When the ♥ Icon is flashing that means the
console is receiving a pulse. It may take a few seconds for the display to reach the
actual number.
STEP 5: While training, you can press STOP button to stop your workout or pull safety key
away from its position to shut down the computer. If you want to resume your workout,
you can press START button and all previous data will resume counting.
STEP 6: At the end of a program you can press FAST/SLOW to display the accumulated data
for speed, time, distance and calories that are memorized during training.
STEP 7: To set a TARGET: Before training, press the ENTER button to be able to program the
time clock to count down. Use the up and down keys to set the time then press Start
or Enter to program the Distance or Calories. If you set multiple parameters, the first
one to reach zero ends the program.
-14-
FT94
To Select a Program:
Step 1:
Step 2:
Press the ^ or v button to choose P1 ~ P5, each program has a preset speed value.
Press the ENTER button to set the count down time from 10:00 to 99:00; the preset
value is 20:00. You can adjust the value by pressing FAST/SLOW or press START
button to start training immediately.
Step 3:
Press STOP button to stop your workout or pull safety key away from its position to shut
down the computer.
Pulse Feature:
The Pulse (Heart Rate) window will display your current heart rate in beats per minute during the
workout. You must use both stainless steel sensors on the front cross bar to display your pulse.
Pulse value displays anytime the upper display is receiving a Pulse signal.
There is an Audio Input Jack on the front of the console and built-in speakers. You may plug any
low-level audio source signal into this port. Audio sources include MP3, Ipod, portable radio, CD
player or even a TV or computer audio signal.
ERROR MESSAGE:
1. LS:
Treadmill doesn t receive the speed signal for 8 seconds.
2. E1:
Memory of console malfunction or CPU accessing problem.
3. Err:
Incline position error.
-15-
FT94
Programmable Features
Speed
Incline
P1
P2
P3
P4
P5
-16-
FT94
General Maintenance
Belt and Bed - Your treadmill uses a very high-efficient low-friction bed. Performance is
maximized when the bed is kept as clean as possible. Use a soft, damp cloth or paper towel to
wipe the edge of the belt and the area between the belt edge and frame. Also reach as far as
practical directly under the belt edge. This should be done once a month to extend belt and bed
life. Use water only - no cleaners or abrasives. A mild soap and water solution along with a nylon
scrub brush will clean the top of the textured belt. Allow to dry before using.
Belt Dust - This occurs during normal break-in or until the belt stabilizes. Wiping excess off with a
damp cloth will minimize buildup.
General Cleaning - Dirt, dust, and pet hair can block air inlets and accumulate on the running
belt. On a monthly basis, vacuum underneath your treadmill to prevent buildup. Once a year, you
should remove the black motor hood and vacuum out dirt that may accumulate. UNPLUG
POWER CORD BEFORE THIS TASK.
BELT ADJUSTMENTS:
Treadbelt Tension Adjustment - Belt tension is not critical for most users. It is very important for
joggers and runners in order to provide a smooth, steady running surface. Adjustment must be
made from the right side of the rear roller in order to adjust tension with the 6 mm Allen wrench
provided in the parts package. The adjustment bolt is located at the end of the right side rail as
noted in diagram below.
Tracking / Tension
Adjustment
Tracking / Tension
Adjustment
Note: Adjustment is through small hole in end cap.
Tighten the rear roller only enough to prevent slippage at the front roller. Turn the treadbelt
tension adjusting bolt in increments of 1/4 turn and inspect for proper tension. When an
adjustment is made to the belt tension, you must also make a tracking adjustment to
compensate for the change in belt tension. This is accomplished by turning both the tension
and tracking Allen bolts an equal amount. This adjustment should be made by turning both bolts
clockwise by no more than a 1/4 turn at a time.
DO NOT OVERTIGHTEN Over tightening will cause belt damage and premature bearing
failure.
-17-
FT94
TREADBELT TRACKING ADJUSTMENT:
The performance of your treadmill is dependent on the frame running on a reasonably level
surface. If the frame is not level, the front and back roller cannot run parallel, and constant belt
adjustment may be necessary.
The treadmill is designed to keep the treadbelt reasonably centered while in use. It is normal for
some belts to drift near one side while the belt is running with no one on it. After a few minutes of
use, the treadbelt should have a tendency to center itself. If, during use, the belt continues to
move toward one side, adjustments are necessary.
TO SET TREADBELT TRACKING:
A 6 mm Allen wrench is provided to adjust the rear roller. Make tracking adjustments from the
left side only. Set belt speed at
approximately 2 to 3 mph. A small adjustment can
make a dramatic difference. Turn the bolt only a 1/4
turn and wait a few minutes for the belt to adjust
itself. Continue to make 1/4 turns until the belt
stabilizes in the center of the running deck. The belt
may require
periodic tracking adjustment depending on use
and walking/running characteristics. Some users
will affect tracking differently. Expect to make adjustments as required to center the treadbelt.
Adjustments will become less of a maintenance concern as the belt is used. Proper belt tracking
is an owner responsibility common with all treadmills.
ATTENTION:
DAMAGE TO THE RUNNING BELT RESULTING FROM IMPROPER TRACKING /
TENSION ADJUSTMENTS IS NOT COVERED UNDER THE FUEL WARRANTY.
-18-
FT94
Belt/deck lubrication procedure:
Do not lubricate with other than FUEL approved lubricant. Your treadmill comes with one tube of
lubricant and extra tubes can be ordered directly from FUEL. There are commercially available lube
kits, but the only one currently approved by FUEL is Lube-N-Walk. These kits come with an
application wand that makes applying the lubrication easier. The kits can be purchased directly from
Lube-N-Walk here: http://www.jadfitness.com/.
Keeping the deck lubricated at the recommended intervals ensures the longest life possible for your
treadmill. If the lubricant dries out, the friction between the belt and deck rises and places undue
stress on the drive motor, drive belt and electronic motor control board, which could result in
catastrophic failure of these expensive components. Failure to lubricate the deck at regular intervals
may void the warranty.
The deck comes pre-lubricated and subsequent lubrication should be performed every 180 hours of
use. The console has a built in lubrication reminder indicator that lights every 180 hours of use. To
lubricate the deck with the tube of lubricant supplied it will be necessary to loosen the walking belt.
Using the 6 mm Allen wrench supplied, loosen the two rear roller adjustment bolts -- located in the
rear end caps enough to get your hand under the belt (5 10 turns). Make sure to loosen both
bolts the same amount of turns and also remember how many turns, because when finished you
will need to tighten the bolts back to the point they were before.
Once the belt is loose, wipe the deck with a clean lint free cloth to remove any dirt. Apply the whole
tube of lubricant onto the deck surface about 18 inches from the motor cover. Squeeze out the
contents of the tube across the deck (parallel to the motor cover) in about a one-foot line, like
toothpaste on a toothbrush. The one-foot line should be in the middle of the deck at approximately
equal distance from both side edges of the belt. You want the lubricant to be applied about the spot
that your feet would hit the belt as you are walking. This should be about 18 inches from the motor
cover, but you may want to walk on the treadmill before loosening the belt to note where your feet
land on the belt. If you mostly run on the treadmill the spot where your feet land may be different
from walking.
Once the lubricant is applied, tighten the rear roller bolts the same amount of turns as when you
loosened them. Run the treadmill at about 6 mph without walking on it for about a minute or two to
make sure the belt stays in the middle of the deck. If the belt tracks to one side then follow the belt
tracking instructions to remedy. Now the deck is lubricated and you should walk, not run, on the
treadmill immediately for at least 5 minutes to ensure the lubricant is evenly distributed. If you
purchase a Lube-N-Walk kit, follow the instructions that come with it to apply the lubrication.
-19-
FT94
Service Checklist - Diagnosis Guide
Before contacting your dealer for aid, please review the following information. It may save you
both time and expense. This list includes common problems that may not be covered under the
treadmill s warranty.
PROBLEM
Display does not light
SOLUTION/CAUSE
Tether cord not in position.
Circuit breaker on front grill tripped. Push circuit breaker in until
it locks.
Plug is disconnected. Make sure plug is firmly pushed into
AC household wall outlet.
Household circuit breaker may be tripped.
Treadmill defect. Contact your FUEL dealer.
Treadbelt does not stay centered
Treadmill belt hesitates when walked/run on
Motor is not responsive / Display is lit
Treadmill will only achieve approximately
7 mph but shows higher speed on display
Treadbelt stops quickly/suddenly when
tether cord is pulled
Treadmill trips on board 15 amp circuit
Computer shuts off when console is
touched (on a cold day) while walking/running
A user may be walking while favoring or
putting more weight on either the left or right
foot. If this walking pattern is natural, track the
belt slightly off-center to the side opposite from
the belt movement. See General Maintenance
section on Treadbelt Tension. Adjust as
necessary.
Make certain clock is running.
This indicates motor should be receiving power to
operate. Low AC voltage to treadmill. Do not use an
extension cord. If an extension cord is required
it should be as short as possible and heavy
duty 16 gauge minimum. Low household
voltage. Contact an electrician or your FUEL
dealer. A minimum of 110 volt AC current is
required.
High belt/deck friction. See General Maintenance
section on lubrication.
High belt/deck friction. See General Maintenance
Treadmill is not grounded. Static electricity is crashing the
computer. Refer to Grounding Instructions on
page 4.
-20-
FT94
Manufacturer’s Limited Warranty
Effective January 1, 2007
TREADMILL WARRANTY
FUEL warrants parts for the FT94 treadmill for a period of time listed below from the date of retail sale, as determined by
sale receipt or in the absence of a receipt eighteen (18) months from the original factory shipping date. FUEL s responsibilities include providing
new or remanufactured parts, at FUELs option, and technical support to our independent dealers and servicing organizations. In the absence of
a dealer or service organization, these warranties will be administered by FUEL directly to a consumer. The warranty period applies to the
following components:
Drive Motor & frame
Parts
Labor
Lifetime
1 Year
1 Year
NORMAL RESPONSIBILITIES OF THE CONSUMER
This warranty applies only to products in ordinary household use, and the consumer is responsible for the items listed below:
1. The warranty registration card must be completed and returned to the address listed on the card within 10 days of the original purchase to
validate the manufacturer s limited warranty.
2. Proper use of the treadmill in accordance with the instructions provided in this manual, including belt tracking.
3. Proper installation in accordance with instructions provided with the treadmill and with all local electric codes.
4. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose connections or defects in
house wiring.
5. Expenses for making the treadmill accessible for servicing, including any item that was not part of the treadmill at the time it was shipped
from the factory.
6. Damages to the treadmill finish during shipping, installation or following installation.
EXCLUSIONS
This warranty does not cover the following:
1. CONSEQUENTIAL, COLLATERAL, OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES
RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY.
Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may
not apply to you.
2. Service call reimbursement to the consumer. Service call reimbursement to the dealer that does not involve malfunction or defects in
workmanship or material, for units that are beyond the warranty period, for units that are beyond the service call reimbursement period,
for treadmills not requiring component replacement, or treadmills not in ordinary household use.
3. Damages caused by services performed by persons other than authorized FUEL servicers; use of parts other than original FUEL parts; or
external causes such as alterations, modifications, abuse, misuse, accident, improper maintenance, inadequate power supply, or acts of
God.
4. Products with original serial numbers that have been removed or altered.
5. Products that have been sold, transferred, bartered, or given to a third party.
6. Products that do not have a warranty registration card on file at FUEL. FUEL reserves the right to request proof of purchase if
no warranty record exists for the product.
7. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, INCLUDING THE WARRANTIES
OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE.
SERVICE
Keep your bill of sale. Twelve (12) months from the date on the bill of sale or eighteen (18) months from the date of factory shipping as
determined by the serial number establishes the warranty period should service be required. If service is performed, it is in your best interest to
obtain and keep all receipts. This written warranty gives you specific legal rights. You may also have other rights that vary from state to state.
Service under this warranty must be obtained by following these steps, in order:
1. Contact your selling authorized FUEL dealer. OR
2. Contact your local authorized FUEL service organization.
3. If there is a question as to where to obtain service, contact our service department at 866-545-3835.
4. If no local service is available, FUEL will repair or replace the parts, at FUELs option, within the warranty period at no charge for parts. All
transportation costs, both to our factory and upon return to the owner, are the responsibility of the owner. The owner is responsible for
adequate packaging upon return to FUEL. FUEL is not responsible for damages in shipping. Make all freight damage claims with the
appropriate freight carrier. DO NOT SHIP ANY UNIT TO OUR FACTORY WITHOUT A RETURN AUTHORIZATION NUMBER. All units arriving
without a return authorization number will be refused.
5. For any further information, or to contact our service department by mail, send your correspondence to:
FUEL Fitness
P.O. Box 2037
Jonesboro, AR 72402-2037
Product features or specifications as described or illustrated are subject to change without notice. All warranties are made by
FUEL.
-21-
FT94