Owner`s manual | Fuji Bikes UG230 Series Network Card User Manual

OWNER'S MANUAL
CIWP4206 A
CIWP4206
42 INCH
ANALOG / DIGITAL
PLASMA DISPLAY TV
TO RECEIVE DIGITAL/ANALOG SIGNAL, YOU MUST CONNECT ANTENNA.
HIGH-DEFINITION TELEVISION
By changing the screen display mode from time to time,
you can reduce burn-in on screen.
(Refer to “CHANGING THE SCREEN DISPLAY MODE” on page 21.)
IF YOU NEED ADDITIONAL ASSISTANCE WITH SET-UP OR OPERATING AFTER
READING OWNER’S MANUAL, PLEASE CALL TOLL FREE 1-800-474-0045,
OR VISIT OUR WEB SITE AT http://www.funai-corp.com
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT WITHIN
THIS UNIT.
THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
The important note is located on the rear of the cabinet.
IMPORTANT SAFETY INSTRUCTIONS
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A
grounding-type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11. Only use attachments/accessories specified by
the manufacturer.
2
EN
PORTABLE CART WARNING
12. Use only with the cart, stand,
tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When
a cart is used, use caution
when moving the cart/apparatus combination to avoid injury S3126A
from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or
moisture, does not operate normally, or has
been dropped.
15. Apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such
as vases, shall be placed on the apparatus.
To reduce the risk of fire or electric shock, do
not expose this appliance to rain or moisture.
•
•
•
•
Place your TV in a room with adequate ventilation.
Keep your TV set away from sources of direct heat, such as heat registers or direct sunlight.
Do not place your TV on soft surfaces, such as rugs or blankets.
Leave enough room for air to circulate around the bottom, top and back of the set.
FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications
to this equipment may cause harmful interference unless the modifications are expressly
approved in the manual. The user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground should be
connected to the grounding system of the building as close to the point of cable entry as practical.
The serial number of this product may be found on the back of the TV. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft.
Model No.
Date of Purchase
Serial No.
Dealer Phone No.
Dealer Purchase from
Dealer Address
A NOTE ABOUT RECYCLING:
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
When moving this TV
Optional Accessories
Due to the weight of this TV, two people should be
used when moving it. Both people should make sure
to grasp the top of the TV with one hand and the
base of the TV with the other hand, as in the following illustration.
To mount the TV on a wall, the following accessory
is needed:
IMPORTANT SAFETY INSTRUCTIONS / PRECAUTIONS
PRECAUTIONS
VISIONMOUNT™ Flat Panel TV Wall Mount from
SANUS SYSTEMS, for large flat panel televisions
(32" to 60"). Refer to page 31 for mounting the TV.
NOTE:
• The wall mounts are not supplied with the TV.
# CAUTION
• This TV is for use only with the Sanus Systems
Model VMPL. Wall Mount.
Use with other wall mounts may result in instability, causing possible injury.
• When mounting the TV with the Sanus Systems
wall mount, make sure to mount it on the wood
studs inside the wall, as failure to do so may
result in instability, causing possible injury.
• Refer to the instruction manual included with
the wall mount for details when securing the TV
to the wall.
3
EN
SUPPLIED ACCESSORIES
• Owner’s Manual
(1EMN22014A)
• Quick Set Up
(1EMN22015A)
• Remote control unit
(NF009UD)
• Batteries
(“AA” x 2)
• Power Cable
(WBC0192LW001)
• If you need to replace these accessories, please refer to the PART NO. with the illustrations and call our toll
free customer support line found on the cover of this manual.
• Depending on your antenna system, you may need different types of Combiners (Mixers) or Separator
(Splitters). Contact your local electronics store for these items.
FEATURES
• DTV/TV/CATV
You can use your remote control to select channels which are broadcast in conventional analog, standard
definition, and high definition formats. Also, cable subscribers can access their cable TV channels.
• Program Information Display (DTV only)
You can display the title, contents and other information of the current DTV program on the screen.
• Autoscan
This TV can automatically scan and memorize the channels receivable in your residential area. This feature eliminates the need of a difficult setting procedure.
• V-CHIP
This feature allows you to block children’s access to inappropriate programs.
• Closed Caption Decoder
This TV contains the built-in Closed Caption Decoder that displays text across the screen. It allows you to read
the dialogue of a TV program or other information in the Closed Caption-supported programs.
• MTS/SAP Tuner
This feature allows you to select with the remote control your desired audio language.
• Auto Shut Off Function
If there is no signal input from the antenna terminal and no operation for 15 minutes, the unit will turn itself
off automatically.
• Choices for On-Screen Menu Language
Select your setup menu language: English, Spanish or French.
• Stereo Sound Function
• Full-Function Remote Control
• PLL Frequency Synthesized Tuning
• HDMI Input
This TV accepts 480i / 480p / 720p / 1080i video signals and 32kHz / 44.1kHz / 48kHz audio signals.
• Component VIDEO Input
This TV accepts 480i / 480p / 720p / 1080i video signals.
• S-VIDEO Input
• AV Input
• Analog Audio Output
• Digital Audio Output (Coaxial)
• Resume
This feature will automatically memorize settings if a power failure occurs.
4
EN
IMPORTANT SAFETY INSTRUCTIONS
PRECAUTIONS . . . . . . . . . . . . . . . . . .
SUPPLIED ACCESSORIES . . . . . . . . .
FEATURES . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
2
3
4
4
FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
REMOTE CONTROL, FRONT AND REAR PANEL FUNCTION
INSTALLING THE BATTERIES . . . . . . . . . . . . . . . . . . . . . . . .
BATTERY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . .
REMOTE CONTROL RANGE . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
6
7
7
7
PREPARATION FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
ANTENNA CABLE CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CONNECTION TO CABLE/SATELLITE BOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CONNECTING OTHER DEVICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
COMPONENT CABLE CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
S-VIDEO CABLE CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
VIDEO CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
DIGITAL AUDIO CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
ANALOG AUDIO CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
CONNECTING THE POWER CABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
INITIAL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
INITIAL SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CHANNEL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
AUTOSCAN . . . . . . . . . . . . . .
CHANNEL LIST . . . . . . . . . . .
MANUAL REGISTER . . . . . . .
ANTENNA CONFIRMATION . .
LANGUAGE SELECTION . . . .
SETTING THE PANEL SAVER
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
14
15
15
16
17
17
SUPPLIED ACCESSORIES / FEATURES / CONTENTS
CONTENTS
WATCHING TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
CHANNEL SELECTION . . . . . . . . . . . . . . .
VOLUME ADJUSTMENT . . . . . . . . . . . . . .
STILL MODE . . . . . . . . . . . . . . . . . . . . . . .
SELECTING AUDIO CHANNELS . . . . . . . .
ACCESSING EXTERNAL DEVICES . . . . . .
CHANGING THE SCREEN DISPLAY MODE
SCREEN INFORMATION . . . . . . . . . . . . . .
SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
...
...
...
...
...
...
...
...
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
18
18
19
19
20
21
22
23
OPTIONAL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
SETUP SCREEN . . . . . . .
PICTURE ADJUSTMENT .
CLOSED CAPTION . . . . . .
DTV CLOSED CAPTION . .
CLOSED CAPTION STYLE
V-CHIP . . . . . . . . . . . . . . .
HDMI AUDIO . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
23
24
25
26
26
28
30
ATTACHING A WALL MOUNT BRACKET (SOLD SEPARATELY) . . . . . . . . . . . . . . . . . . . . . .31
MISCELLANEOUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
GLOSSARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back cover
SYMBOLS USED IN THIS MANUAL
The following is the description for the symbols used in this manual.
TV
: Settings only for the analog mode
DTV
: Settings only for the digital mode
• If there is no symbol under the function heading, those are common settings for the analog
mode and digital mode.
5
EN
FUNCTIONS
REMOTE CONTROL, CONTROL AND REAR PANEL FUNCTION
INPUT SELECT button (p20)
Press to access connected external
devices like a DVD recorder or VCR.
SLEEP button (p23)
Press to activate the sleep timer.
INPUT
SLEEP SELECT
POWER
POWER button (p13)
Press to turn the TV on and off.
AUDIO button (p19)
1
2
3
4
5
6
Press to display on-screen menu.
7
8
9
s / B / K / L buttons (p13)
To move left / right / up / down through
the items.
-
0
Number buttons (p18)
Press to select a channel.
SETUP button (p23)
Cycles through audio options.
• Analog mode (TV)
Selects audio mode.
• Digital mode (DTV)
Selects audio language.
AUDIO
STILL button (p19)
STILL
Press to pause screen image.
SCREEN
MODE
SETUP
ENTER button (p13)
Press to confirm your selection.
SCREEN MODE button (p21)
Press to select screen aspect ratio.
INFO button
ENTER
• Analog mode (TV) (p22)
To display channel No., signal type
and TV setting.
• Digital mode (DTV) (p22)
To display channel information, signal
type and TV setting.
• External input mode (p20)
To display external input mode, signal
type and TV setting.
INFO
BACK
BACK button (p22)
Press to return to previous menu operation.
CH RETURN
VOL.
VOL. X/ Y buttons (p18)
MUTE
CH
Press to adjust volume.
MUTE button (p18)
Press to turn sound on and off.
CH RETURN button (p18)
Press to return to previously viewed channel.
CH K/ L buttons (p18/p20)
To select channels and external input
mode.
INPUT SELECT/ENTER
button (p20/p13)
Infrared Sensor Window
Receives infrared rays transmitted from the remote control.
• To access connected external
devices like a DVD recorder or
VCR.
• To decide the command of
setting when the menu is displayed.
STANDBY indicator
Illuminates when TV is in standby mode. Disappears when the
power is ON.
CHANNEL K/ L buttons (p18)
SETUP
VOLUME
CHANNEL
INPUT SELECT /
ENTER
STANDBY ON
POWER
To select channels and move
up/down through the menu items.
Lights up when the power is ON.
POWER button (p13)
VOLUME X/ Y buttons (p18)
To adjust volume and move
right(X)/left(Y) through the
menu items.
ON indicator
SETUP
VOLUME
CHANNEL
INPUT SELECT /
ENTER
STANDBY
ON
POWER
To turn TV on/off.
SETUP button (p23)
To display on-screen menu.
NOTE:
• With buttons [VOL. X/Y] or [MUTE], you can only adjust the volume of the main unit. You cannot adjust the volume of the external
devices with these buttons.
About Interference to Infrared Devices
Please note in advance that using other infrared devices
(such as infrared cordless headphones) near the plasma
display may cause infrared interference to occur.
About Pixel Defects
A plasma display is created by using a collection of miniature
pixels. It is possible to display more than 99.99% of valid pixels, however a small fraction of pixels over the life of the
product may not illuminate or may constantly be illuminated.
This is not to be considered a defect in the plasma panel.
6
EN
Preventing Image Burn on the plasma display
Fixed images displayed on the plasma display for an
extended period of several hours may cause uneven pixel
aging causing damage to the plasma display. You should
try to avoid displaying fixed images for extended periods
on the plasma display.
Images of high luminance displayed on the plasma display
for more than 60 seconds may cause lingering images to
remain on the screen. These images will automatically disappear, but may take time depending on the luminance of the
images and how long they were displayed on the screen.
DIGITAL AUDIO OUT
(COAXIAL) jack
Digital audio coaxial
cable connection for
decoder or audio
receiver. Connect
cable to DIGITAL
AUDIO IN jack of
external device.
from underneath
HDMI
ANT. IN
AUDIO OUT
HDMI IN jack
HDMI cable connection for external
video equipment (i.e.DVD recorder).
AUDIO
L
DIGITAL
AUDIO OUT
(COAXIAL)
by side
AUDIO OUT jacks
Audio cable connection for external
audio equipment. Use AUDIO IN jacks
of external equipment.
L
HDMI IN
R
R
Rear of this TV
R
AUDIO
L
VIDEO2 and AUDIO
jacks
Video and audio cable
connection for external
equipment.
VIDEO2
COMPONENT2
HDMI
ANT. IN
COMPONENT1
Y
AUDIO OUT
DIGITAL
AUDIO OUT
(COAXIAL)
S-VIDEO2
COMPONENT2
S-VIDEO2 jack
S-Video cable and audio
(VIDEO2) cable connection for
external video equipment.
Pb
Pr
L
R
HDMI IN
L
AUDIO
R
Pb
Pr
L
AUDIO
R
VIDEO1
L
AUDIO
R
Pr
S-VIDEO1
COMPONENT1
Y
L
AUDIO
R
AC IN
Y
Pb
AUDIO
L
R
L
AUDIO
R
Y
VIDEO1
Pb
L
AUDIO
R
Pr
S-VIDEO1
from underneath
COMPONENT2 and AUDIO
jacks
Component cable connection
for external audio/video
devices. Use component and
audio out jacks of external
device.
COMPONENT1 and AUDIO
jacks
Component cable connection for
external audio/video devices.
Use component and audio out
jacks of external device.
AUDIO jacks (for DVI connection)
Audio cable connection for
external audio/video
devices with DVI jack. Use
AUDIO OUT jacks of external equipment when using
an HDMI-DVI conversion
cable.
VIDEO1 and AUDIO
jacks
Video and audio cable
connection for external
equipment.
FUNCTIONS
ANT. IN jack
Coaxial cable connection for your
antenna or cable box.
S-VIDEO1 jack
S-Video cable and audio
(VIDEO1) cable connection for external video
equipment.
INSTALLING THE BATTERIES
Install two AA batteries (included) matching the polarity (++ / – –) indicated inside battery compartment of
the remote control.
[BATTERY PRECAUTIONS]
• Be sure to follow the correct polarity as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries with fresh
ones.
• If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury
from possible battery leakage.
• Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
REMOTE CONTROL RANGE
Operate the remote control within a 30 degree angle on both sides of the infrared sensor on the main unit.
You can operate the remote control from a distance of several yards away from the main unit.
NOTE:
• Other devices which use infrared beams,
Within 30 degrees
Approximately 5.5 yds (5 m)
Within 30 degrees
Approximately 5.5 yds (5 m)
Approximately
7.6 yds (7 m)
sunlight, fluorescent lights, etc., may affect
the range and effectiveness of the remote
control. Make sure the TV is positioned in a
place which minimizes interference from
them.
7
EN
PREPARATION FOR USE
CONNECTION
This section describes how to connect your TV to an antenna, cable box, etc.
MAKE SURE YOU HAVE AN ANTENNA.
As DTV is only available over the air, you need an antenna to receive a digital signal.
NOTE:
• Be sure your antenna or other source is connected properly before plugging in the power cord.
[ANTENNA CABLE CONNECTION]
1) When connecting your TV to an antenna
Connect the Coaxial cable on your home outlet to the ANT. IN jack of this TV.
2) When connecting TV to cable TV company (without box)
Connect the Coaxial cable on your home outlet to the ANT. IN jack of this TV.
Rear of this TV
VHF / UHF
antenna
Coaxial cable
(not included)
or
ANT. IN
Coaxial cable
Cable TV
company
(not included)
*Once connections are completed, turn on the TV and begin initial setup.
Channel scanning is necessary for the TV to memorize all available channels in your area.
(Refer to “INITIAL SETUP” on page 13.)
NOTES:
• For your safety and to avoid damage to equipment, please unplug the coaxial cable from the ANT.IN jack before moving the unit.
• If you use an antenna in order to receive analog TV, the same antenna generally will work for DTV reception.
Outdoor or attic antennas will be more effective than set-top versions.
• To easily switch between antenna and cable wires, you can purchase an “Antenna Selector” commercially available.
• If you connect a cable system directly, contact the CATV installer.
[CONNECTION TO CABLE/SATELLITE BOX]
1) Connect the coaxial cable on your home outlet to the input jack of the CABLE/SATELLITE box.
2) Use another coaxial cable to connect the ANT. IN jack of your TV to the output jack of the CABLE/SATELLITE box.
*Required cables in 2) and connecting methods differ depending on the CABLE/SATELLITE box. For more information, please contact your cable/satellite provider.
Rear of this TV
Satellite
dish
Cable box or
Satellite box
or
Cable TV
company
8
EN
Coaxial cable
Coaxial cable
(not included)
(not included)
ANT. IN
CONNECTING OTHER DEVICES
[HDMI]
1) High Definition Multimedia Interface (HDMI) uses the latest technology to ensure the signal maintains the
highest degree of integrity from source to TV. Both video and audio travel through a single cable.
PREPARATION FOR USE
HDMI cable (not included)
To HDMI IN jack
HDMI
ANT. IN
HDMI OUT
AUDIO OUT
To HDMI output jack
DIGITAL
AUDIO OUT
(COAXIAL)
DVD Player with the HDMI output jack
AUDIO
L
L
R
R
HDMI IN
Rear of this TV
NOTES:
• This TV accepts 480i / 480p / 720p / 1080i video signals, and 32kHz / 44.1kHz / 48kHz audio signals.
• This TV accepts only 2 channel audio signal (LPCM).
• You need to select “PCM” for the digital audio output of the device you connect or the HDMI audio setting. Audio sometimes makes
no sound if you select “Bitstream”, etc.
• This TV only accepts signals corresponding EIA861.
2) When your video device has a DVI output jack, connect the HDMI conversion cable (not included) from the
DVI output jack.
HDMI-DVI conversion cable (not included)
To DVI output jack
To HDMI IN jack
DVI OUT
HDMI
ANT. IN
AUDIO OUT
Cable Box or Satellite Box
with the DVI output jack
AUDIO OUT
R
L
L
R
R
HDMI IN
DIGITAL
AUDIO OUT
(COAXIAL)
To audio
output jacks
AUDIO
L
To AUDIO Rear of this TV
input jacks
Audio cable (not included)
NOTES:
• This TV accepts 480i / 480p / 720p / 1080i video signals.
• An HDMI conversion cable requires a separate audio cable connection as well.
• Audio signals are converted from digital to analog if you make the connection in paragraph 2) above.
• DVI does not show image if the 480i does not accept EIA/CEA-861/861B.
“HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.”
9
EN
[COMPONENT CABLE CONNECTION]
Offers better picture quality for video devices connected to your TV.
Use a component video cable (not included) to connect your TV to external video devices equipped with
component video jacks.
If you connect to your TV’s COMPONENT1 input jack, connect audio cables to the AUDIO L/R jacks of COMPONENT1.
If you connect to your TV’s COMPONENT2 input jack, connect audio cables to the AUDIO L/R jacks of COMPONENT2.
Component video cable (not included)
To component video
output jacks
COMPONENT2
To COMPONENT1
input jacks
COMPONENT1
Y
L
AUDIO
R
DVD Player with the component
video output jacks
Pb
Pr
L
AUDIO
R
Y
VIDEO1
Pb
L
AUDIO
R
Pr
Rear of this TV
To AUDIO
input jacks
To audio
output jacks
S-VIDEO1
Audio cable (not included)
NOTE:
• This TV accepts 480i / 480p / 720p / 1080i video signals.
[S-VIDEO CABLE CONNECTION]
Offers good picture quality for video devices connected to your TV.
Use an S-video cable (not included) to connect your TV to external video devices equipped with S-video connectors.
If you connect to your TV’s S-VIDEO1 input jack, connect audio cables to the AUDIO L/R jacks of VIDEO1.
If you connect to your TV’s S-VIDEO2 input jack, connect audio cables to the AUDIO L/R jacks of VIDEO2.
Side of this TV
To AUDIO input jacks
R
AUDIO
L
VIDEO2
To S-VIDEO2 input jack
S-VIDEO2
S-video cable (not included)
To S-VIDEO1
input jack
VIDEO S-VIDEO
OUT
OUT
COMPONENT2
COMPONENT1
Y
AUDIO
OUT
To S-video
output jack
DVD/VCR with
the S-video output jack
L
AUDIO
R
Pb
Pr
L
AUDIO
R
Y
VIDEO1
Pb
L
AUDIO
R
Pr
To AUDIO
input jacks
To audio
output jacks
Audio cable (not included)
NOTE:
• If you connect to the S-VIDEO jack and the VIDEO jack at the same time, the S-Video connection will have priority.
10
EN
S-VIDEO1
Rear of this TV
[VIDEO CONNECTION]
Offers standard picture quality for video devices connected to your TV.
When the audio jack of the video device is monaural, connect the audio cable to the audio L input jack.
Side of this TV
To AUDIO input jacks
R
AUDIO
VIDEO2
PREPARATION FOR USE
L
To VIDEO2 input jack
S-VIDEO2
Video cable (not included)
To VIDEO1
input jack
To video
output jack
AUDIO
OUT
Camcorder
COMPONENT2
COMPONENT1
Y
VIDEO
OUT
L
AUDIO
R
Video Game
Pb
Pr
L
AUDIO
R
Y
VIDEO1
Pb
L
AUDIO
R
Pr
To audio
output jacks
VCR
To AUDIO
input jacks
S-VIDEO1
Rear of this TV
Audio cable (not included)
[DIGITAL AUDIO CONNECTION]
If you connect this TV to an external digital audio device, you can enjoy multi-channel audio like 5.1ch digital
broadcasting sound. Required digital audio coaxial cable not included.
Rear of this TV
MD deck, DAT deck, etc.
To coaxial digital
audio input jack
HDMI
ANT. IN
AUDIO OUT
AUDIO
COAXIAL
DIGITAL
AUDIO OUT
(COAXIAL)
Dolby Digital decoder
L
L
R
R
HDMI IN
To DIGITAL AUDIO
OUT jack
Digital audio coaxial cable
(not included)
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
11
EN
[ANALOG AUDIO CONNECTION]
If you connect this TV to an external analog audio device, you can enjoy stereophonic (2 channel) audio
sound. Required audio cable not included.
To audio input jacks
HDMI
ANT. IN
AUDIO OUT
AUDIO
IN
DIGITAL
AUDIO OUT
(COAXIAL)
AUDIO
L
L
R
R
HDMI IN
Stereo system
Audio cable
(not included)
To AUDIO
OUT jacks
Rear of this TV
CONNECTING THE POWER CABLE
Connect the power cord (included) to the TV before connecting it to the power source.
HDMI
ANT. IN
COMPONENT2
COMPONENT1
Y
AUDIO OUT
DIGITAL
AUDIO OUT
(COAXIAL)
AC IN
Y
VIDEO1
Pb
L
AUDIO
R
AUDIO
L
L
R
R
HDMI IN
L
AUDIO
R
Pb
Pr
L
AUDIO
R
Pr
S-VIDEO1
AC IN
2
1
1
Connect the power cable to this TV first.
2
Connect the power cable to an AC outlet.
12
EN
# CAUTION
• Do not connect the power cable to a power
supply outside the indicated voltage of this TV
(AC 120V). Connecting the power cable to a
power supply outside of this range may result in
fire or electrical shocks.
• Always use the power cable included with this
TV. Do not use any other cable.
For safety, make sure to always connect the
power cable to a three pronged AC outlet.
INITIAL SETTINGS
4
INITIAL SETUP
Select source of ANT. IN jack using [K /L], press
[ENTER].
This section will guide you through your TV’s initial
set up which includes selecting a language for your
on-screen menu and AUTOSCAN, which automatically scans and memorizes viewable channels.
Initial Setup
Or
Cable
ANT IN
2
3
4
5
6
7
8
9
-
0
5
AUDIO
ENTER
Enter
BACK
SETUP
Back
Exit
PREPARATION FOR USE / INITIAL SETTINGS
Select
1
Cable
Air
INPUT
SLEEP SELECT
POWER
Air
Make sure the antenna is connected to "ANT IN" jack.
Select the destination of "ANT IN" jack.
Autoscan will start automatically.
Initial Setup
STILL
Now the system is scanning for channels,please wait.
SCREEN
MODE
SETUP
5%
ENTER
Analog channels
1ch
Digital channels
0ch
SETUP
INFO
BACK
1
After making all the necessary connections, turn
on your TV.
2
Press [POWER]. Initial Setup menu will appear.
• This operation may take a few moments.
• If Initial Setup menu does not appear, press
and hold [ENTER] for 3 seconds, initial setup
will appear then proceed to step 3.
• If initial set up has already been completed,
refer to “LANGUAGE SELECTION” on page 17.
3
When you first turn on your TV, the following
screen is displayed. Use [K /L] to select the
on-screen menu language from the choices on
the right side of the screen.
Exit
• When scanning has completed, the lowest
memorized channel will be displayed.
NOTES:
• If you do not operate your TV for more than 45 seconds during the initial setup, the message boxes start to move to the
lower left-hand corner of the screen to prevent burn-in. This
is to save your screen from burn-in. Press any key except
[POWER] to cancel it.
• The initial Autoscan function can be executed for either “Air”
or “Cable” only once. When you change the connection
(Air/Cable), set the “Autoscan” again. (Refer to page 14.)
• If you connect a cable system directly, contact the CATV
installer.
• When the scanning is not completed, Helpful Hint will be
displayed every time you turn on the power. If you have
previously registered channels when this screen appears
you can select a channel with [the Number buttons].
2-0
Initial Setup
Select the language for setup display.
English
Elija idioma de preparación.
Español
Sélectionner langue écran config.
Français
No channel is registered.
Press and hold "ENTER" key for 3 seconds.
Contact support hotline provided on manual or back of unit.
Sin canal registrado.
Mantenga oprimida la tecla "ENTER" durante 3 segundos.
Llame teléfono de apoyo en manual o atrás de TV.
Select
ENTER
Enter
SETUP
Exit
The Antenna Confirmation menu on step 4 will
be displayed in the selected language after you
press [ENTER].
Pas de chaîne consign.
Maintenir la touche "ENTER" pressée 3 secondes.
Contacter numero d'urgence dans manuel ou arrière appareil.
• Toll free customer support line can be found on the cover
of this manual.
13
EN
CHANNEL SETTINGS
3
AUTOSCAN
For TV channels, using [K /L], select “Air”.
For CATV channels, select “Cable”.
With AUTOSCAN, your TV automatically scans and
memorizes your area’s viewable channels. Activate
AUTOSCAN when you turn on your TV for the first
time, change broadcast sources (e.g. from antenna
to CATV), or move your TV to a different broadcast
area.
Autoscan
Back
Autoscan will rescan all channels.
This may take a while to complete.
Air
Select the destination of "ANT IN" jack.
Cable
Air
Cable
1hour
Cable
Or
ANT IN
STILL
-
0
SCREEN
MODE
SETUP
• Press [ENTER].
Scanning and memorizing the channels automatically starts.
ENTER
INFO
BACK
Now the system is scanning for channels, please wait.
72%
CH RETURN
Analog channels
VOL.
MUTE
CH
SETUP
NOTE:
• Make sure the TV is connected to antenna or cable.
1
Display the setup screen.
• Press [SETUP].
The following setup screen appears.
2
Select “CHANNEL” and press [ENTER] to confirm.
• Using [K /L], select “Autoscan”.
Channel
Autoscan
Channel List
Manual Register
Antenna
• Press [ENTER].
14
EN
10ch
Digital channels
6ch
Exit
• When the scanning and memorizing are completed, the lowest memorized channel in the
broadcasting will be displayed.
NOTES:
• If you do not operate this TV for more than 45 seconds
during initial setup, the message boxes start to move to
the lower left-hand corner of the screen. This is to save
your screen from burn-in. Press any key except
[POWER] to cancel it.
• If you connect a cable system directly, contact the CATV
installer.
• If you press [POWER] or [SETUP] during Autoscan, this
setting will be canceled.
• If there is no reception connected or a poor signal is detected, a Hint will appear on screen once scanning stops.
CHANNEL LIST
MANUAL REGISTER
This function lets you remove undesired channels
from the Channel Registration List.
This function lets you manually add channels not
memorized due to poor broadcast strength during
AUTOSCAN.
STILL
0
SCREEN
MODE
SETUP
1
2
3
4
5
6
7
8
9
-
0
AUDIO
ENTER
INFO
BACK
STILL
CH RETURN
1
SETUP
Display the setup screen.
ENTER
• Press [SETUP].
The following setup screen appears.
2
SCREEN
MODE
CHANNEL SETTINGS
-
INFO
BACK
1
Display the setup screen.
• Press [SETUP].
The following setup screen appears.
2
Select “CHANNEL” and press [ENTER] to confirm.
• Using [K /L], select “Manual Register”.
Select “CHANNEL” and press [ENTER] to confirm.
• Using [K /L], select “Channel List”.
Channel
Autoscan
Channel List
Manual Register
Antenna
Channel
Autoscan
Channel List
Manual Register
Antenna
• Press [ENTER].
3
Select the channel you want to remove.
• Using [K/L], select the channel.
Channel List
Highlight channels for
Ch Up/Down key selection.
DTV
6
DTV
8
DTV
48
DTV
67
• Press [ENTER].
3
9
27
Select the channel you want to add.
• Using [the Number buttons], select your
desired channel.
58
Ch Select
ENTER
Watch/Skip
BACK
• Press [ENTER] to highlight the channel selected for removal. You will not be able to select the
channel again using [CH K/L].
• To reactivate the removed channel, highlight it
and press [ENTER].
• When you remove a major channel, you
remove its minor channels, too.
NOTE:
• The channel with “DTV” indicated on the display is ATSC,
otherwise the channel is NTSC.
4
11
Back
To exit the setup, press [SETUP].
Manual Register
For Analog channels,
select a channel to register
using number keys.
For Digital channels,
you must perform Autoscan function.
BACK
Ch Change
Register
Back
• Select “Register” with [ENTER].
4
To exit the setup, press [SETUP].
NOTES:
• If set up completes successfully, “Registered to the Channel
List” is displayed.
• If Video 1 is being used, set up will not be completed successfully and “Unavailable” will be displayed on the screen.
15
EN
• If the channel is set to external input, you cannot confirm the antenna situation.
ANTENNA CONFIRMATION
Displays signal strength for each channel.
Video1
Antenna
INPUT
SLEEP SELECT
POWER
Back
1
2
3
4
5
6
7
8
9
Indicator is available
for antenna signal only.
AUDIO
CH
Ch Change
STILL
-
0
3
SCREEN
MODE
SETUP
ENTER
INFO
BACK
CH RETURN
VOL.
1
CH
MUTE
Display the setup screen.
• Press [SETUP].
The following setup screen appears.
2
Select “CHANNEL” and press [ENTER] to confirm.
• Using [K /L], select “Antenna”.
Channel
Autoscan
Channel List
Manual Register
Antenna
• Press [ENTER].
• Using [the Number buttons] or [CH K /L],
select the channel for which you want to check
signal strength.
11
Antenna
Back
Now
70 Peak
CH
16
EN
80
Ch Change
To exit the setup, press [SETUP].
LANGUAGE SELECTION
SETTING THE PANEL SAVER
You can choose English, Spanish, or French as
your on screen language.
Panel saver prevents the display from being etched
by an unchanging image. You can specify a setting
for it.
STILL
-
0
STILL
SCREEN
MODE
SETUP
-
0
SCREEN
MODE
SETUP
ENTER
INFO
BACK
ENTER
INFO
BACK
VOL.
MUTE
CH RETURN
CH
VOL.
1
CH
MUTE
Display the setup screen.
• Press [SETUP].
The following setup screen appears.
2
CHANNEL SETTINGS
CH RETURN
Select “LANGUAGE” and press [ENTER] to confirm.
• Using [K /L], select “English”, “Español” or
“Français”.
1
Display the setup screen.
• Press [SETUP].
The following setup screen appears.
2
Select “DETAIL” and press [ENTER] to confirm.
• Using [K /L], select “Panel Saver” and press
[ENTER] to confirm.
Detail
Language
Closed Caption
Select the language for setup display.
English
Elija idioma de preparación.
Español
Sélectionner langue écran config.
Français
• Press [ENTER].
3
V–chip
3
To exit the setup, press [SETUP].
HDMI Audio
Auto
Panel Saver
Off
Switch the Panel Saver mode.
• Using [K /L], select “Strong”, “Weak” or “Off”
and press [ENTER] to confirm.
Panel Saver
This function is useful for
Strong
burn-in reduction of the display
Weak
panel by shifting the picture
Off
element.
Select the level for effect.
NOTE:
• "Weak" moves 1 pixel every 5 minutes and "Strong" moves
1 pixel every minute. This prevents burn-in.
4
To exit the setup, press [SETUP].
17
EN
WATCHING TV
CHANNEL SELECTION
Select channels by pressing [CH K/L] found on
remote control or on the TV’s control panel, or by
pressing [the Number buttons] found on the remote
control.
1
2
3
4
5
6
7
8
9
ATSC
18:00
CH4-1 No signal No signal
18:30
CH4-1
CH4-2
CH4-3
19:00
CH4
CH4-1 No signal CH4-3
INPUT
SLEEP SELECT
POWER
19:30
CH4-1
CH4-2 No signal
20:00
AUDIO
STILL
-
NTSC
: change automatically
: change manually by pressing [CH
on your remote control
/ ]
0
SCREEN
MODE
SETUP
NOTE:
• “No Signal” will appear on the screen after the minor
ENTER
INFO
BACK
CH RETURN
VOL.
MUTE
VOLUME ADJUSTMENT
CH
[CH K/L]
• Use [CH K/L] to change the channel.
• Same operation is also available with [CHANNEL
K/L] on the control panel of the main unit.
[the Number buttons]
• Press the channel number with [the Number
buttons] to select a channel you want to watch,
then press [ENTER].
- When selecting analog channel 12
1
2
ENTER
- When selecting digital channel 12-1
Be sure to press [–] before entering the minor
channel number.
1
2
-
1
NOTE:
• In DTV broadcasting, one channel sometimes broadcasts
multiple programs depending on the air time. In this case,
the main channel is called major channel and the minor
channel is called minor channel.
About minor channel broadcasting:
There may be different programs being broadcast on minor channels through a single channel from ATSC. You can watch each minor
channel program being broadcast by selecting
one of the minor channels.
EN
This section describes how to adjust the volume.
The mute function, which turns the sound off and
on, will also be described.
INFO
BACK
CH RETURN
VOL.
MUTE
CH
[VOL. X/Y]
• Use [VOL. X/Y] to adjust the audio volume.
• The same operation is available with [VOLUME
X/Y] on the control panel of the main unit.
• The volume bar will be displayed at the bottom
of the screen when adjusting the volume.
Volume
20
ENTER
• If the channel broadcasts NTSC and ATSC both
and you don't press [–], you will receive the
NTSC channel only. The moment you press [–],
the lowest memorized digital channel will be displayed.
• Press [CH RETURN] to return to the previously
viewed channel.
18
channel broadcast is over.
You will need to change the channel to continue
watching another TV program.
• The volume bar display will automatically disappear in a few seconds.
[MUTE]
• Press [MUTE] to turn off and on the sound.
Mute
• “Mute” is displayed on the screen for a few seconds.
• Press [MUTE] again or [VOL. X/Y] ([VOLUME
X/Y]) to release the Mute status.
Press [AUDIO] to cycle through available audio
channels.
STILL MODE
You can freeze the image shown on the screen.
1
2
3
4
5
6
7
8
9
When the broadcasting has all audio...
SAP / STEREO
SAP / MONO
SAP / STEREO
AUDIO
STILL
0
SCREEN
MODE
1
When the broadcasting has stereo audio and
monaural audio...
MONO / STEREO
Pause the image.
• When you press [STILL], the image shown on
the screen is paused.
MONO / STEREO
When the broadcasting has SAP and monaural
audio...
SAP / MONO
WATCHING TV
SETUP
SAP / MONO
Still
• The audio is not paused and keeps on reading
out.
• If the digital signal is gone or protected, the
image will remain paused and the audio will be
muted.
• The Still function will be released after 5
minutes.
2
Canceling Still function.
• The Still function will be canceled by pressing
any button while Still function is working.
When the broadcasting is having only monaural
audio...
MONO
(cannot be switched.)
STEREO : Outputs stereo-audio
SAP
: Outputs second audio program
MONO : Outputs mono-audio
DTV
When you press [AUDIO], the currently selected
language and the number of available languages
will be displayed on the screen.
NOTE:
6-1
• Press any key except [POWER] to cancel still mode.
English 1/3
SELECTING AUDIO CHANNELS
This section describes how to switch the audio in
the analog mode and how to switch the audio language in the digital mode.
Press [AUDIO] to cycle through available audio
languages.
English 1/3
Other 3/3
AUDIO
7
8
-
0
9
STILL
SETUP
SCREEN
MODE
Spanish 2/3
• Available languages differ depending on the
broadcast.
• The information display will automatically disappear in one minute.
TV
NOTE:
When you press [AUDIO], the currently selected
audio mode will be displayed on the screen
• Pressing [AUDIO] does not control external audio source.
6
SAP / STEREO
19
EN
ACCESSING EXTERNAL DEVICES
Use your remote control to access DVD recorders,
home audio systems and other external devices
when they are connected to your television.
INPUT
SLEEP SELECT
POWER
1
2
3
4
5
6
7
8
9
• When you press [INFO], the current external
input mode, the type of resolutions for video
signal, TV aspect ratio, CC and TV rating will
be displayed at the top-right of the screen.
• The information display will automatically disappear in 1 minute.
1) When using VIDEO1 or S-VIDEO1 input jack
AUDIO
Video1
480i
STILL
-
SD
TV-PG DLSV CC
0
SCREEN
MODE
SETUP
ENTER
INFO
BACK
2) When using VIDEO2 or S-VIDEO2 input jack
Video2
CH RETURN
480i
VOL.
MUTE
CH
Use your remote control to select external component.
• When you press [INPUT SELECT] or [CH L]
on the remote control, the input mode will be
switched as below.
SD
TV-PG DLSV CC
3) When using COMPONENT1 input jacks
Component1
1080i
HD
NONE
TV/DTV channel
Video1
4) When using COMPONENT2 input jacks
Component2
1080i
Video2
HD
NONE
Component1
5) When using HDMI IN jack
Component2
HDMI
1080i
HD
NONE
HDMI
• Pressing [CH K] on the remote control reverses
direction.
• To use the VIDEO1 or S-VIDEO1 input jack on
the TV, select “Video1”.
• To use the VIDEO2 or S-VIDEO2 input jack on
the TV, select “Video2”.
• To use the COMPONENT1 input jacks on the
TV, select “Component1”.
• To use the COMPONENT2 input jacks on the
TV, select “Component2”.
20
EN
• To use the HDMI IN jack on the TV,
select “HDMI”.
16:9
CHANGING THE SCREEN DISPLAY MODE
Each of 4 display modes can be selected in either
4:3 or 16:9 aspect ratios.
AUDIO
8
9
STILL
-
2
Press [SCREEN MODE] repeatedly until the
normal screen displays.
0
NOTES:
SCREEN
MODE
SETUP
• Some programs may not offer all display mode options.
• By changing the screen display mode from time to time, you
can reduce burn-in on screen.
ENTER
BACK
Press [SCREEN MODE], to switch the TV
aspect ratio.
INFO
When the broadcast is sending 4:3 video
signal...
When the broadcast is sending 16:9 video
signal...
Sidebar
(normal)
Full
Full
(normal)
Zoom
Wide
Cinema
Expand
Cinema
[Sidebar]
Sidebar displays a 4:3 picture at its standard
4:3 size. Sidebars will be displayed on the right
and left edges of the screen.
[Full]
Full displays a 4:3 picture at a 16:9 size, with
horizontal elongation necessary to fill the
screen.
[Cinema]
Cinema displays a 4:3 picture at a 16:9 size,
with less horizontal elongation necessary to fill
the screen because a little bit of the top and
bottom edge of the screen will be cut off.
[Wide]
Wide displays the center of the picture as original
size and the outer sides of the picture will be
elongated. The size of the picture will depend on
the original signal.
WATCHING TV
7
1
[Full]
A picture is displayed at 16:9 size as it is.
[Zoom]
Zoom displays a 16:9 picture without changing
its horizontal and vertical ratio, at its maximum
size.
[Cinema]
Cinema displays a 16:9 picture with vertical
elongation.
[Expand]
Expand displays a 16:9 picture with horizontal
elongation.
21
EN
DTV
SCREEN INFORMATION
You can display the currently selected channel or
other information such as the audio mode on the
screen.
1
AUDIO
7
8
9
-
0
SCREEN
MODE
• The following information is displayed.
ENTER
(1) Program title
INFO
BACK
(2) Broadcast station
CH RETURN
VOL.
MUTE
Display the detailed information for the channel.
• Press [INFO] on the remote control.
The currently selected program details are displayed on the screen.
STILL
SETUP
In the digital mode, the detailed information for the
current channel such as the Program guide is displayed.
(3) Program guide (max. 4 lines displayed)
CH
(4) Channel number
TV
In the analog mode, the current channel and the
audio mode are displayed.
1
(5) Audio language (“Other” is displayed when
the audio language cannot be acquired, or
the acquired languages are other than
English, Spanish or French.)
Display the channel number and the audio
mode.
(6) Effective scanning lines and scan mode
• Press [INFO] on the remote control.
The current channel number, audio mode, type
of resolutions for video signal, TV aspect ratio,
CC and TV rating are displayed at the top-right
of the screen.
(8) Program aspect ratio
(7) Program definition
(9) Program rating
(10) CC (Not available if the CC set to “Off”)
(1)
Buffy Vampire Slayer
6
SAP / STEREO
480i
480i
SD
SD
4:3
4:3
(2)
(4)
HDTV
A quarter-century ago,which may now qualify as the
good old days of newspapering,run-of-paper sales
accounted for 80 percent of the industry's advertising
revenues.Department stores and supermarket were
6-1
(5)
English 1/2
1080i
1080i
HD
HD
16:9
16:9
TV-PG DLSV CC
CC
(6), (7), (8)
TV-PG DLSV CC
CC
(3)
• To clear the display, press [BACK] or [INFO]
again.
(9) (10)
NOTES:
• When the program guide is displayed in more than 4 lines,
use [ K/ L] to scroll.
• “No description provided” is displayed when the program
guide is not provided.
• The following screen is displayed when connecting to external devices:
e.g.) When using VIDEO1 input jack for connection
Video1
480i
480i
SD
SD
TV-PG DLSV CC
CC
22
EN
OPTIONAL SETTINGS
SLEEP TIMER
SETUP SCREEN
The Sleep Timer can be set to automatically turn
off your television after an incremental period of
time.
This section describes the overview of the setup
screen displayed when you press [SETUP].
For more details, see the reference page for each
item.
INPUT
SLEEP SELECT
POWER
1
2
3
4
5
6
The setup screen consists of the function setting
items below.
•
AUDIO
7
8
-
0
To exit settings.
9
STILL
•
SCREEN
MODE
You can adjust the picture quality (Picture Mode,
Brightness, Contrast, Color, Tint, Sharpness,
Color Temp.).
(Refer to “PICTURE ADJUSTMENT” on page 24.)
ENTER
1
Press [SLEEP] on the remote control to set the
Sleep Timer.
•
• The setting display for Sleep Timer is shown on
the screen.
Sleep
WATCHING TV / OPTIONAL SETTINGS
SETUP
You can automatically scan the viewable channels
and remove those that are undesired.
(Refer to “AUTOSCAN” on page 14.)
Off
•
2
You can change closed captioning display formats
and font styles. (Refer to “CLOSED CAPTION” on
page 25.)
Block children’s access to inappropriate programming. (Refer to “V-CHIP” on page 28.)
And select HDMI Audio if your TV is connected to
a digital external device like a DVD recorder.
(Refer to “HDMI AUDIO” on page 30.)
You can set your TV to turn off after a set period
of time (from 10 to 90 minutes). After set up, you
can display the remaining time before shut off by
pressing [SLEEP] again.
• To cancel the sleep timer, press [SLEEP]
repeatedly until “Sleep Off” is displayed.
Sleep
Off
• The Sleep Timer setting display will automatically disappear in a few seconds.
NOTE:
• When you disconnect your TV from its power source or
when a power failure occurs, the sleep timer setting will be
canceled.
•
You can change the language (English, Spanish,
French) displayed on the setup screen.
(Refer to “LANGUAGE SELECTION” on page 17.)
NOTES:
• To cancel the setup screen, press [SETUP].
• If you do not operate this TV for more than 45 seconds during initial setup, the message boxes start to move to the
lower left-hand corner of the screen. This is to save your
screen from burn-in. Press any key except [POWER] to cancel it.
23
EN
Contrast
Using [s / B], adjust to increase or decrease
contrast.
s: To decrease contrast
B: To increase contrast
PICTURE ADJUSTMENT
You can select from four default picture color settings. You can also adjust brightness, contrast,
color, tint, sharpness and color temperature settings.
Contrast
SCREEN
MODE
SETUP
INFO
Color
1
Display the setup screen.
Enter
Adjust
60
36
Tint
0
Sharpness
0
ENTER
Enter
Move
ENTER
Enter
Reset Settings
Using [K /L], select “Reset”.
You can reset setting of the Picture Mode you select.
Dynamic
30
Move
Sharpness 0
Picture
Color
Enter
Sharpness
Using [s / B], adjust the detail of the picture.
s: To soft
B: To clear
Select “PICTURE”, and press [ENTER] to confirm.
• Using [K /L], select your desired item and
press [ENTER] to confirm.
Contrast
ENTER
R2
Adjust
Brightness
Move
Tint
Using [s / B], adjust to obtain natural skin tones.
s: To red
B: To green
Tint
Picture Mode
ENTER
36
Adjust
• Press [SETUP].
The following setup screen appears.
2
Move
Color
Using [s / B], adjust to be brilliant or pale color.
s: To pale
B: To brilliant
ENTER
BACK
60
Adjust
Reset Settings
This function resets the
Cancel
"Dynamic" setting for Picture Mode
Reset
to factory default.
Reset Settings
Neutral
Color Temp.
3
Adjust the picture quality.
• Using [K/L], select the picture quality you want
to adjust.
Color Temp.
Using [K/L], adjust Color Temperature from the selection, then press [ENTER]. (Cool, Neutral and Warm)
Picture Mode
Using [K /L], adjust Picture Mode from the
selection, then press [ENTER]. (Standard,
Dynamic, Movie and News)
Picture
Picture Mode
Brightness
Contrast
Color
Tint
Picture
Sharpness
Picture Mode
Standard
Brightness
Dynamic
Contrast
Movie
Color
News
Cool
Reset Settings
Neutral
Color Temp.
Warm
Tint
• The adjustment bar for picture quality item is
displayed on the screen.
Sharpness
Reset Settings
Color Temp.
Brightness
Using [s / B], adjust until the darkest parts of
the picture are as bright as you prefer.
s: To decrease brightness
B: To increase brightness
Brightness
30
Adjust
24
EN
Move
ENTER
Enter
NOTE:
• To move to the normal screen, press [SETUP].
4
To exit the setup, press [SETUP].
[Caption Mode]
CLOSED CAPTION
CC1 and Text1:
are the primary caption and text services.
The captioning or text is displayed in the same
language as the program’s dialogue
You can view closed captioning (cc) for TV programs, movies, news, and prerecorded tapes.
Closed captions refer to text of dialogue or descriptions displayed on-screen for the hearing impaired.
(up to 4 lines of script on the screen, where it
does not obstruct relevant parts of the picture).
STILL
-
0
SCREEN
MODE
SETUP
CC3 and Text3:
serve as the preferred data channels.
The captioning or text is often a secondary language translation, simplified English or displayed
at a slower rate.
ENTER
INFO
BACK
CH RETURN
Display the setup screen.
• Press [SETUP].
The following setup screen appears.
OPTIONAL SETTINGS
1
CC2, CC4, Text2 and Text4:
are rarely available and broadcasters use them
only in special conditions, such as when CC1
and CC3 are not available or Text1 and Text3 are
not available.
• There are three display modes according to
programs:
2
Select “DETAIL” and press [ENTER] to confirm.
• Using [K /L], select “Closed Caption” and press
[ENTER] to confirm.
5
Detail
Closed Caption
V–chip
3
HDMI Audio
Auto
Panel Saver
Off
Select “Conventional CC” and press [ENTER] to
confirm.
Conventional CC
Off
DTV CC
Off
To exit the setup, press [SETUP].
NOTES:
Closed Caption
CC Style
4
Paint-on mode: Displays input characters on the
screen immediately.
Pop-on mode : Once characters are stored in
memory, they are displayed all
at once.
Roll-up mode : Displays the characters continuously by scrolling (max. 4 lines).
Select the Closed Caption mode.
• Closed captions must be broadcast or included in your
recorded content to appear on your TV.
• If the closed caption is not broadcasted, nothing is displayed.
• The closed caption is not displayed when you use HDMI
connection.
• When your TV receives a special effects playback signal
(i.e., Search, Slow and Still) from a VCR’s video output
channel (CH3 or CH4), the TV may not display the correct
caption or text.
• Captions and texts may not match the TV voice exactly.
• Interference may cause the closed caption system not to
function properly.
• The caption or text characters will not be displayed while the
menu display or functions display is shown.
• If a black box appears on the screen, this means that the
TV is set to TEXT mode. To clear screen, select CAPTION
“CC1”, “CC2” , “CC3”, “CC4”or “Off”.
Closed Caption
Conventional CC
Off
DTV CC
CC1
CC Style
CC2
CC3
CC4
Text1
Text2
Text3
Text4
• Using [K /L], select the desired closed caption,
then press [ENTER].
25
EN
DTV CLOSED CAPTION
CLOSED CAPTION STYLE
DTV
DTV
Apart from closed captions, DTV has its own closed
captions called DTV CC. Use this menu to change
the settings for DTV CC.
1
1
Display the setup screen.
• Press [SETUP].
The following setup screen appears.
Display the setup screen.
• Press [SETUP].
The following setup screen appears.
2
2
Select “DETAIL” and press [ENTER] to confirm.
• Using [K /L], select “Closed Caption” and press
[ENTER] to confirm.
Select “DETAIL” and press [ENTER] to confirm.
• Using [K /L], select “Closed Caption” and press
[ENTER] to confirm.
Detail
Closed Caption
V–chip
HDMI Audio
Auto
Panel Saver
Off
Detail
Closed Caption
V–chip
HDMI Audio
Auto
Panel Saver
Off
3
Select “CC Style” and press [ENTER] to confirm.
Closed Caption
3
Select “DTV CC” and press [ENTER] to confirm.
Conventional CC
Off
DTV CC
Off
CC Style
Closed Caption
Conventional CC
Off
DTV CC
Off
CC Style
4
Switch the Closed Caption Style.
CC Style
User Setting
4
Font Style
Switch the DTV Closed Caption mode.
Closed Caption
Conventional CC
Off
Font0
Font Size
Middle
Font Color
White
Font Opacity
Solid
Back Color
Black
Back Opacity
Solid
DTV CC
Off
Edge Color
Black
CC Style
Service1
Edge Type
None
Service2
Service3
• Using [K /L], select the desired Closed Caption
Style.
Service4
Service5
Service6
• Using [K /L], select the desired DTV Closed
Caption, then press [ENTER].
Off:
Select if you do not want DTV CC. This is the
default.
Service 1 to Service 6:
Select one of these before changing any other
item in the Closed Caption menu. Choose
Service 1 under normal circumstances.
5
Use “User Setting”.
• The “User Setting” function lets you change CC
style.
• Using [K /L], select “User Setting”.
• Press [ENTER] and set “User Setting” to “On”.
CC Style
User Setting
On
Font Style
Off
Font Size
Font Color
Font Opacity
Back Color
5
26
EN
Back Opacity
To exit the setup, press [SETUP].
Edge Color
Edge Type
[Font Opacity]
Font opacity of the displayed caption can be
switched as below.
Set each item.
• When “User Setting” is set to “On”, you can set
the following items.
• CC style set by “User Setting” will be displayed.
• Using [K /L], select the item you want to set.
• You can switch the setting for each item with
[K /L].
CC Style
Closed Caption
User Setting
Font Style
Font Size
Font Color
Font Opacity
Solid
Back Color
Flash
Back Opacity
Translucent
Edge Color
Transparent
Edge Type
Picture display
[Back Color]
Background color of the displayed caption can
be switched as below.
ABCDEF
GHIJKL
ABCDEFGHIJKL
CC Style
Edge
(Edge Color and Edge Type)
Closed Caption
User Setting
Font
(Font Style, Font Size, Font Color and Font Opacity)
Back
(Back Color and Back Opacity)
• The setting description for each item is shown
below.
Font Style
White
Font Size
Black
Font Color
Red
Font Opacity
Green
Back Color
Blue
Back Opacity
Yellow
Edge Color
Magenta
Edge Type
Cyan
OPTIONAL SETTINGS
6
[Back Opacity]
Background opacity of the displayed caption can
be switched as below.
[Font Style]
Closed Captioning font style can be changed as
below.
CC Style
Closed Caption
User Setting
CC Style
Closed Caption
Font Style
User Setting
Font Size
Font Style
Font Color
Font Opacity
Font Size
Font Color
Back Color
Solid
Font Opacity
Back Opacity
Flash
Back Color
Edge Color
Translucent
Back Opacity
Edge Type
Transparent
Edge Color
Edge Type
[Edge Color]
Edge color of the displayed caption can be
switched as below.
[Font Size]
Font size of the displayed caption can be
switched as below.
CC Style
Closed Caption
User Setting
CC Style
Closed Caption
Font Style
White
Font Size
Black
Font Color
Red
Font Size
Large
Font Opacity
Green
Font Color
Middle
Back Color
Blue
Small
Back Opacity
Yellow
Back Color
Edge Color
Magenta
Back Opacity
Edge Type
Cyan
User Setting
Font Style
Font Opacity
Edge Color
Edge Type
[Edge Type]
Edge type of the displayed caption can be
switched as below.
[Font Color]
Font color of the displayed caption can be
switched as below.
CC Style
Closed Caption
User Setting
CC Style
Closed Caption
Font Style
Font Size
User Setting
Font Style
White
Font Size
Black
Font Color
Red
Font Opacity
Green
Back Color
Blue
Back Opacity
Yellow
Edge Color
Magenta
Edge Type
Cyan
7
Font Color
None
Font Opacity
Raised
Back Color
Depressed
Back Opacity
Uniform
Edge Color
L.Shadow
Edge Type
R.Shadow
To exit the setup, press [SETUP].
27
EN
V-CHIP
3
You can block certain programming inappropriate for
children. This block can be released by entering a
password.
Enter the password.
• Use [the Number buttons] and enter the
4-digit number.
V-Chip
INPUT
SLEEP SELECT
POWER
Enter password.
1
2
3
4
5
6
BACK
PIN Code
AUDIO
7
8
• When you have not set up your password,
enter 0000.
• When the password is correct, the following
“V-Chip” screen is displayed.
9
STILL
-
0
SCREEN
MODE
SETUP
Back
A MPAA Rating
V-Chip
ENTER
MPAA Rating
B TV Rating
TV Rating
INFO
BACK
New Password
C New Password
1
Display the setup screen.
• Press [SETUP].
The following setup screen appears.
See the following description for setting each
item.
A MPAA Rating
4
Display the “MPAA Rating” screen.
• Using [K /L], select “MPAA Rating”.
V-Chip
2
Select “DETAIL” and press [ENTER].
• Using [K /L], select “V-chip”.
MPAA Rating
TV Rating
New Password
Detail
Closed Caption
V–chip
HDMI Audio
Auto
Panel Saver
Off
• Press [ENTER].
V-Chip
X
NC-17
R
PG-13
PG
G
NR
• Press [ENTER].
The password entry screen is displayed.
V-Chip
Select
Enter password.
PIN Code
28
EN
BACK
Back
ENTER
View/Block
BACK
Back
Set “MPAA Rating”.
• Using [K /L], select the rating.
• Press [ENTER] and set to “View” or “Block”.
5
• Press [ENTER] and set to “View” or “Block” for
the rating without sub categories.
V-Chip
X
NC-17
R
PG-13
PG
G
NR
Select
6
V-Chip
FV V
ENTER
View/Block
BACK
Back
PG-13 :
PG :
G:
NR :
<Rating Category Explanations>
Mature audience only
No one under 17 admitted
Restricted; under 17 requires
accompanying parent or adult
guardian
Unsuitable for children under 13
Parental Guidance suggested
General Audience
No Rating
NOTES:
• When you select a rating and set it to “Block”, the higher
ratings will be blocked automatically. The lower ratings will
be available for viewing.
• When you set “X” to “View”, all ratings turn to “View”
automatically.
B TV Rating
Display the “TV Rating” screen.
• Using [K /L], select “TV Rating”.
V-Chip
MPAA Rating
TV Rating
New Password
L
D
Select
ENTER
View/Block
BACK
Back
• For the rating with sub categories,
press [K /L / s / B] and select the rating. Then
press [ENTER] and set to “View” or “Block”.
V-Chip
FV V
S
L
D
TV-MA
TV-14
TV-PG
TV-G
TV-Y7
TV-Y
Select
6
ENTER
View/Block
BACK
Back
To exit the setup, press [SETUP].
<Selection>
TV-MA :
TV-14 :
TV-PG :
TV-G :
TV-Y7 :
TV-Y :
<Rating Category Explanations>
Mature audience only
Unsuitable for children under 14
Parental Guidance suggested
General Audience
Appropriate for children 7 and
older
Appropriate for all children
<Selection>
FV :
V:
S:
L:
D:
<Rating Sub Category Explanations>
Fantasy Violence
Violence
Sexual Situation
Coarse Language
Suggestive Dialogue
NOTES:
• Press [ENTER].
V-Chip
FV V
S
L
D
TV-MA
TV-14
TV-PG
TV-G
TV-Y7
TV-Y
Select
S
TV-MA
TV-14
TV-PG
TV-G
TV-Y7
TV-Y
To exit the setup, press [SETUP].
<Selection>
X:
NC-17 :
R:
4
Set “TV Rating”.
• Using [K /L], select the rating.
OPTIONAL SETTINGS
5
ENTER
View/Block
BACK
• When you select a rating and set it to “Block”, the higher
ratings will be blocked automatically. The lower ratings will
be available for viewing.
• When you set “TV-MA” to “View”, all ratings turn to “View”
automatically.
Back
29
EN
C New Password
HDMI AUDIO
4
Set the method of sound input for HDMI jack.
Display the “New Password” screen.
• Using [K /L], select “New Password”.
STILL
-
0
SCREEN
MODE
SETUP
V-Chip
MPAA Rating
TV Rating
New Password
ENTER
INFO
BACK
1
• Press [ENTER].
5
Display the setup screen.
• Press [SETUP].
The following setup screen is displayed.
Change the password.
• Use [the Number buttons] on the remote control and enter the NEW 4-digit password.
• Enter password again in “Confirm password”
space.
V-Chip
Enter password.
2
Confirm password.
PIN Code
BACK
Back
Select “DETAIL” and press [ENTER] to confirm.
• Using [K /L], select “HDMI Audio” and press
[ENTER] to confirm.
Detail
6
Closed Caption
To exit the setup, press [SETUP].
V–chip
HDMI Audio
Auto
Panel Saver
Off
NOTES:
• Make sure to enter the exact same new password as the
“Confirm password.”. If they are different, the space is
cleared for reentering.
• Your password will be erased and return to the default
(0000) when a power failure occurs or when you turn off the
power using a wall switch. If you forget the password,
unplug the power cord for 10 seconds to restore the password to 0000.
3
Switch the HDMI Audio.
• Using [K /L], select the desired HDMI Audio,
then press [ENTER].
Detail
Closed Caption
V–chip
HDMI Audio
Auto
Panel Saver
Digital
Analog
• Select “Auto” if you connected to both digital
device with HDMI jack and analog device for
audio sources. Digital audio input signal has
priority in this setting.
• Select “Digital” if you connected to digital
device with HDMI jack for digital audio input
signal.
• Select “Analog” if you connected to analog
device with analog jacks for analog audio input
signal.
4
30
EN
To exit the setup, press [SETUP].
ATTACHING A WALL MOUNT BRACKET (SOLD SEPARATELY)
The following is a description of the method for attaching a wall mount to the TV.
When performing this operation, refer to the instruction manual included with the wall mount kit.
# CAUTION
• Any damage caused by incorrectly attempting to mount the TV is not covered under the terms of the
manufacturer’s warranty.
• This TV is for use only with the Sanus Systems Model VMPL. Wall Mount. Use with other wall mounts
may result in instability causing possible injury.
2
OPTIONAL SETTINGS / ATTACHING A WALL MOUNT BRACKET (SOLD SEPARATELY)
Rear of this TV
1
1
HDMI
ANT. IN
COMPONENT2
COMPONENT1
Y
AUDIO OUT
DIGITAL
AUDIO OUT
(COAXIAL)
AC IN
Y
VIDEO1
Pb
L
AUDIO
R
AUDIO
L
L
R
R
HDMI IN
L
AUDIO
R
Pb
Pr
L
AUDIO
R
Pr
S-VIDEO1
Stands
1
Turn the TV over and place it screen-first onto a
table which has a soft cloth draped over it.
Place the TV in a way so that the stands hang
over the edge of the table.
NOTES:
• Make sure to use a table which can support the
weight of the TV and is larger than the TV.
• Make sure the table is in a stable location.
2
Remove the stands from the TV.
Unscrew the M5 screws indicated by 1 , and
remove the left and right stands.
NOTE:
• The screws and stands you have removed are necessary for reattachment at a later date. Make sure to
keep them in a safe place.
3
NOTES:
• Only use the screw holes indicated by 2 for mounting the TV.
• For instructions on how to attach the TV rails, refer to
the instruction manual included with the mount wall
kit.
4
Attach the TV to the wall.
NOTE:
• Refer to the instruction manual included with the
mount wall when securing the TV to the wall.
* If you want to attach the stands of this TV again,
insert the stand slowly as illustrated below and
drive screws in the 4 threaded holes ( 1 ).
Attach the left and right TV rails to the TV using
the M8 screws included with the wall mount kit.
2 indicates the position of the screw holes on
the TV.
1
31
EN
MISCELLANEOUS
TROUBLESHOOTING GUIDE
Before calling for service, please refer to the following information.
Symptom
32
EN
Remedy
No power
• Be sure the power cord is connected to outlet.
• If a power failure occurs, unplug the power cord for 30 minutes
to allow the unit to reset itself.
No picture or sound
• Check if the power is on.
• Check the outlet connection.
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and
connection.
• View other TV channels. The problem might be limited to the
broadcasting station.
• Turn off the power and wait for about 1 minute, then turn it on
again.
No color
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and
connection.
• View other TV channels. The problem might be limited to the
broadcasting station.
• Adjust the Color in the setup screen.
Sound OK, picture poor
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and
connection.
• Electrical interference from nearby appliances may affect picture
quality.
• Adjust Contrast and Brightness in the setup screen.
• View other TV channels. The problem might be limited to the
broadcasting station.
Picture distorted
• When the outside antenna is used, check the wire condition and
connection.
• View other TV channels. The problem might be limited to the
broadcasting station.
Weak picture
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and
connection.
• Adjust Contrast and Brightness in the setup screen.
• View other TV channels. The problem might be limited to the
broadcasting station.
Lines or streaks in picture
• When the outside antenna is used, check the wire condition and
connection.
• Electrical interference from nearby appliances may affect picture
quality.
• View other TV channels. The problem might be limited to the
broadcasting station.
Picture blurred
• When the outside antenna is used, check the wire condition and
connection.
• View other TV channels. The problem might be limited to the
broadcasting station.
Remedy
Ghosts in picture
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and
connection.
• Electrical interference from nearby appliances may affect picture
quality.
• View other TV channels. The problem might be limited to the
broadcasting station.
Bars on screen
• When the outside antenna is used, check the wire condition and
connection.
• Electrical interference from nearby appliances may affect picture
quality.
Picture rolls vertically
• When the outside antenna is used, check the wire condition and
connection.
• Electrical interference from nearby appliances may affect picture
quality.
• View other TV channels. The problem might be limited to the
broadcasting station.
Different color marks on screen
• Move your TV away from nearby electric appliances. Turn off the
power and wait 30 minutes before turning it back on.
• View other TV channels. The problem might be limited to the
broadcasting station.
Poor reception on some channels
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and
connection.
• Electrical interference from nearby appliances may affect picture
quality.
• View other TV channels. The problem might be limited to the
broadcasting station.
Picture OK, sound poor
• Electrical interference from nearby appliances may affect picture
quality.
• View other TV channels. The problem might be limited to the
broadcasting station.
Burn-in on screen
• Do not continuously display images such as video games, computer graphics, stock market quotations or other fixed patterns.
Those images may cause screen burn-in.
If burn-in occurs, display a movie or TV show to reduce the
problem.
These images can cause permanent damage to your screen.
Burn-in caused by misuse is not covered by your warranty.
No reception of digital signals
• Make sure Autoscan has been completed (Refer to “AUTOSCAN” on
page 14). Autoscan must be completed when you set up your TV for
the first time or move it to a location where previously unavailable
channels are broadcast.
• The selected channel may not be broadcasting.
• When Autoscan is interrupted, some channels will not be
received. Make sure to complete Autoscan in the setup screen.
Channel changes automatically
• Many digital channels have alternate channel numbers. TV changes the
numbers automatically to the ones signifying the broadcasting stations.
These are the numbers used for analog broadcasts.
Remote Control doesn’t work
• Check the antenna or cable connection to the main unit.
• Check the batteries of the remote control.
• Check if there is an obstacle between the sensor and the
remote control.
• Test the signal output. If OK, there might be remote sensor trouble. (Refer to “IR SIGNAL CHECK” on page 36.)
MISCELLANEOUS
Symptom
33
EN
Problems with Closed Caption Feature
Misspelled captions are displayed.
• Closed captioning production companies may broadcast programs without correcting the misspelling in a live broadcast.
Captions are not entirely displayed, or • Captions that are delayed a few seconds behind the actual dialogue
are common for live broadcasts. Most captioning production compacaptions are delayed behind the dianies can display a dialogue to a maximum of 220 words per minute. If
logue.
a dialogue exceeds that rate, selective editing is used to ensure that
the captions remain up-to-date with the current TV screen dialogue.
34
EN
Captions are displayed as a white
box.
No caption is displayed in the Closed
Caption-supported program.
• Interference from buildings or weather conditions may cause
captioning to be incomplete.
• Broadcasting station may shorten the program to insert advertisement. The closed caption decoder cannot read the information of the shortened program.
No caption is displayed when playing
the videotape containing captions.
• The videotape may be illegally copied, or the caption signal
might not have been read during copying.
Black box is displayed in the screen.
• “Text” mode is selected for caption. Select “CC1”, “CC2”, “CC3”,
“CC4” or “Off”.
•IGNITION NOISE:
Black spots or horizontal streaks may appear, picture may flutter or drift.
Usually caused by interference from automobile ignition systems, neon
lamps, electrical drills and other electrical appliances.
•GHOSTS:
Ghosts are caused by the television signal following two paths. One is
the direct path and the other is reflected from tall buildings, hills or some
other objects. Changing the direction or position of the antenna may
improve reception. Ghosting may also be caused by defects in the
antenna system such as unshielded leads or connecting several sets to
the same antenna without using multiple antenna couplers.
Ghosting occurring when the TV is connected to a cable TV system may
indicate a bad cable wire or loose connection. Confirm that the cable wire
is properly connected.
MISCELLANEOUS
•SNOW:
If your receiver is located in the fringe area of a television station where
the signal is weak, your picture may be marred by the appearance of
small dots. When the signal is extremely weak, it may be necessary to
install a special antenna to improve the picture.
Snowing occurring when the TV is connected to a cable TV system may
indicate a bad cable wire or loose connection. Confirm that the cable wire
is properly connected.
•RADIO FREQUENCY INTERFERENCE:
The interference produces moving ripples or diagonal streaks, and in
some cases, causes loss of contrast in the picture.
•PREVENTION OF AN OBSTACLE TO RADIO RECEIVERS:
This TV has been designed pursuant to the FCC class B Rules. This is to
prevent a problem to Radio receivers. lf this TV causes a problem to
Radio receivers, then take the following steps:
- Keep the monitor away from Radio.
- Adjust Radio antennas in order for the TV not to receive
interference.
- The antenna cable of Radio should be kept away from the TV.
- Use a coaxial cable for antenna.
You can check if this TV influences Radio receivers by turning off all
other equipment other than the TV.
If you find a problem receiving Radio when using the TV, check the
instructions mentioned above.
Vertical stripes appear,
depending on the screen
contents.
•The plasma display panel is lighting the phosphors by the discharge of
internal radiation. Depending on the screen contents, in rare cases this
may cause vertical stripes to appear because of failure to light. Please
note that this is not a malfunction.
35
EN
GLOSSARY
ATSC
Acronym that stands for Advanced
Television Systems Committee and
the name of the digital broadcasting
standards.
Aspect ratio
The width of a TV screen relative
to its height. Conventional TVs are
4:3 (in other words, the screen is
almost square); widescreen models are 16:9 (the screen is almost
twice as wide as its height).
Component video
This is a video signal format that
conveys each of three principal
colors of light (red, blue and
green) through different signal
lines. This allows the viewers to
experience picture colors as original as it is. There are several signal formats, including Y / Pb / Pr
and Y / Cb / Cr.
Dolby Digital
The system developed by Dolby
Laboratories to compress digital
sound. It offers stereo sound (2ch)
or multi-channel audio.
HDMI (High-Definition
Multimedia Interface)
Interface that supports all uncompressed, digital audio/video formats
including set-top box, DVD player or
digital television, over a single cable.
High Definition TV (HDTV)
Ultimate digital format that produces
high resolution and high picture quality.
LPCM
(Linear Pulse Code Modulation)
LPCM is a format that can have
up to 8 channels of audio. It is
mainly used in music production.
The format samples and captures
analog signals and transforms
them into digital signals without
compressing the sound data.
NTSC
Acronym that stands for National
Television Systems Committee
and the name of the current analog broadcasting standards.
Password
A stored 4-digit number that
allows access to parental control
features.
SAP
(Secondary Audio Program)
Second-audio channel delivered
separately from main-audio channel. This audio channel is used as
an alternate in bilingual broadcasting.
Standard Definition TV (SDTV)
Standard digital format that is similar to the NTSC picture quality.
S-Video
Offers higher quality images by
delivering each signal, color (c)
and luminance (y) independently
of each other through separate
cables.
MAINTENANCE
CABINET CLEANING
• Always unplug the TV from the AC outlet before
cleaning.
• Clean the case of the TV with a soft cloth which
has been wet and wrung dry.
• If the screen is dirty or dusty, wipe it clean with a
soft cloth.
NOTES:
• Never use a solvent, alcohol or any other abrasive liquid
to clean the TV.
• Always make sure the area around vents on the TV is
clear and clean. Failure to do this may result in fire or
cause the TV to fail prematurely.
SERVICING
Should your unit become inoperative, do not try to
correct the problem yourself. There are no user serviceable parts inside. Turn off the TV, unplug the
power cord and call our toll free customer support
line found on the cover of this manual to locate an
authorized service center.
36
EN
IR SIGNAL CHECK
If the remote control isn’t working properly, you can
use an AM radio or digital camera (including a cellular phone with built-in camera) to see if it is sending
out an infrared signal.
• With an AM radio:
Tune the AM radio station to a
non-broadcasting frequency.
Point the remote control towards
it, push any button and listen. If
the sound from the radio flutters,
it is receiving the remote control’s
infrared signal.
• With a digital camera (including builtin cell phone cameras):
Point a digital camera towards the
remote control. Push any button on
the remote control and look through
the digital camera. If the infrared light
appears through the camera, the
remote control is working.
SPECIFICATIONS
Closed Caption
System:
ATSC
NTSC-M
TV Standard
§15.119/FCC (Analog CC)
§15.122/FCC (Digital CC)
Channel Coverage (ATSC/NTSC)
VHF:
2 ~ 13
UHF:
14 ~ 69
CATV:
2 ~ 13, A ~ W,
W+1 ~ W+94,
A-5 ~ A-1, 5A
Tuning System:
Channel frequency
synthesized tuning system
Channel Access:
Direct access keyboard,
Programmable scan,
and Up/down
Terminals
Antenna Input:
VHF/UHF/CATV
75 ohm unbalanced
(F-type)
S-Video Input:
Mini DIN 4-pin jack x 2
Video Input:
RCA jack x 2
Audio Input:
RCA jack (L/R) x 4
Component Video/Audio Input:
2 pin jacks (Y) / 1Vpp
4 pin jacks (Pb/Pr) / 700mVpp
4 RCA jacks (L/R)
HDMI / Audio Input:
HDMI jack
2 RCA jacks (L/R)
Coaxial Digital Audio Output:
1 pin jack, 500mVpp
Analog Audio Output:
2 RCA jacks (L/R)
Stereo Sound System Speaker
ELECTRICAL SPECIFICATION
Sound Output:
5W, 8 ohm x 4
OTHER SPECIFICATIONS
Remote Control:
Digital encoded
infrared light system
Operating
Temperature:
5°C to 40°C
(41°F to 104°F)
Power Requirements: AC120V, 60Hz
Power Consumption
(Maximum):
400W
Plasma panel:
42" XGA panel
Dimensions:
H : 30-11/16" (780mm)
W: 41-1/2"
(1054mm)
D : 13"
(330mm)
Weight:
92.4 lbs. (42.0kg)
MISCELLANEOUS / SPECIFICATIONS
GENERAL SPECIFICATIONS
Television System:
• Designs and specifications are subject to change without notice and without our legal obligation.
• If there is a discrepancy between languages, the default language will be English.
37
EN
LIMITED WARRANTY
FUNAI CORP. will repair this product, free of charge in CANADA in the event of defect in materials or workmanship
as follows:
DURATION :
PARTS :
LABOR :
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the
date of original retail purchase. Certain parts and LCD image burn-in are not covered under this
warranty.
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of
original retail purchase.
LIMITS AND EXCLUSIONS :
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT OR
OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PRODUCT TO
OBTAIN SERVICE UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing
or if service was attempted by an unauthorized service center. This limited warranty does not apply to any product
not purchased and used in CANADA.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product
not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling,
misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office
use of this product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE
OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL
OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN CANADA.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE
CENTER.
THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SERVICE CENTER.
THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF
NO PROOF OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIRS COSTS
WILL BE CHARGED.
ATTENTION :
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS:
To obtain warranty service, you must take the product, or deliver the product freight prepaid, in either its original packaging
or packaging affording an equal degree of protection, to any AUTHORIZED SERVICE CENTER. FUNAI CORP. will not
reimburse you for any service done by unauthorized service providers without prior written approval.
To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries,
please contact to us at:
FUNAI CORPORATION
Customer Service
Tel: 1-800-474-0045
http://www.funai-corp.com
19900 Van Ness Avenue, Torrance, CA 90501
Printed in Malaysia
L0703CD / L0701CB
1EMN22014A ★★★
L0703CD_QG.qx4
06.9.26
11:06 AM
Page 1
QUICK SET UP
GUIDE D’INSTALLATION RAPIDE
Some cables here are not included with the plasma display TV.
Certains des câbles présentés ici ne sont pas fournis avec le téléviseur écran plasma.
5
Plasma Display TV rear side
Arrière du téléviseur écran plasma
S-VIDEO (OR VIDEO) CONNECTION
CONNEXION S-VIDÉO (OU VIDÉO)
R
5
AUDIO
L
2
VIDEO2
S-VIDEO2
S-VIDEO (OR VIDEO) CONNECTION
CONNEXION S-VIDÉO (OU VIDÉO)
AUDIO OUTPUT CONNECTION
CONEXION DE SORTIE AUDIO
COMPONENT1
COMPONENT2
HDMI
ANT. IN
Y
AUDIO OUT
L
DIGITAL
AUDIO OUT
(COAXIAL)
1
3
ANTENNA
ANTENNE
1
L
L
AUDIO
R
HDMI IN
R
Y
VIDEO1
Power cord is included.
Pb
L
AUDIO
R
Le cordon d’alimentation
est fourni.
AUDIO
R
HDMI CONNECTION
CONNEXION HDMI
L
AUDIO
R
Pb
Pr
4
Pr
S-VIDEO1
COMPONENT CONNECTION
CONNEXION À COMPOSANTES
ANTENNA
ANTENNE
VHF / UHF antenna
Antenne VHF / UHF
Plasma Display TV rear side
OR
OU
Arrière du téléviseur écran plasma
Cable TV company
OR
Compagnie du câble TV
OR
OU
Satellite dish
2
HDMI
ANT. IN
OU
AUDIO OUT
IN
OUT
Cable box or
Satellite box
L
L
R
R
HDMI IN
DIGITAL
AUDIO OUT
(COAXIAL)
Décodeur de câblodistribution
ou décodeur satellite
AUDIO
Antenne parabolique
AUDIO OUTPUT CONNECTION
CONEXION DE SORTIE AUDIO
Analog Audio Output Connection
Plasma Display TV rear side
CONNEXION DE SORTIE AUDIO/VIDÉO ANALOGIQUE
Arrière du téléviseur écran plasma
HDMI
ANT. IN
AU D I O I N
VIDEO
AUX
AUDIO OUT
TV
L
R
DIGITAL
AUDIO OUT
(COAXIAL)
AUDIO
L
L
R
R
HDMI IN
Stereo system
Chaîne stéréo
Digital Audio Output Connection
Plasma Display TV rear side
CONEXION DE SORTIE AUDIO NUMÉRIQUE
Arrière du téléviseur écran plasma
HDMI
ANT. IN
AU D IO IN
VID EO
DIGITAL
AUDIO IN
(COAXIAL)
AU X
AUDIO OUT
TV
L
R
Dolby Digital decoder
Décodeur Dolby Digital
DIGITAL
AUDIO OUT
(COAXIAL)
AUDIO
L
L
R
R
HDMI IN
L0703CD_QG.qx4
3
06.9.26
11:06 AM
Page 2
HDMI CONNECTION
CONNEXION HDMI
DVR or DVD Player With HDMI Out Jack
Plasma Display TV rear side
DVR ou Lecteur DVD avec prise de sortie HDMI
Arrière du téléviseur écran plasma
HDMI
ANT. IN
AUDIO OUT
HDMI OUT
DIGITAL
AUDIO OUT
(COAXIAL)
4
AUDIO
L
L
R
R
HDMI IN
COMPONENT CONNECTION
CONNEXION À COMPOSANTES
DVD Player With Component Video Out Jack
Lecteur DVD avec prises de sortie vidéo à composantes
Plasma Display TV rear side
Arrière du téléviseur écran plasma
COMPONENT2
COMPONENT1
Y
AUD IO
OUT
R
5
Y
COMPONENT
VIDEO OUT
L
Y
C b/P b
L
AUDIO
R
C r/P r
Pb
Pr
L
AUDIO
R
Pb
Pr
S-VIDEO (OR VIDEO) CONNECTION
CONNEXION S-VIDÉO (OU VIDÉO)
Plasma Display TV (side view)
Camcorder
Côte du téléviseur écran plasma
CAMÉSCOPE
R
AUDIO
L
VIDEO2
R
L
VIDEO S–VIDEO
OR
OU
S-VIDEO2
Plasma Display TV rear side
DVD Player
VCR
LECTEUR DVD
MAGNÉTOSCOPE
Arrière du téléviseur écran plasma
VIDEO1
VIDEO
OUT
S–VIDEO
VIDEO
AU D I O
OUT
R
L
L
AUDIO
R
S-VIDEO1
OR
OU
FOR MORE INFORMATION
POUR PLUS D’INFORMATIONS
1. Owner’s Manual Mode d’emploi
2. http://www.funai-corp.com
3. 1-800-474-0045
Printed in Malaysia
1EMN22015A
L0703CD / L0701CB ★★★★
Download PDF

advertising