FujiFilm 135V Digital Camera User Manual

fi-5120C / fi-5220C Image Scanner Operator Guide
TROUBLE SHOOTING
CONTENTS MAP
fi-5120C / fi-5220C Image Scanner Operator Guide P3PC-1322-05ENZ2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
INTRODUCTION
Thank you for purchasing the fi-5120C / fi-5220C Duplex Color Scanner product.
This document describes how to handle fi-5120C / fi-5220C Duplex Color and basic operation methods. Before you start
using fi-5120C / fi-5220C Duplex Color be sure to thoroughly read this manual to ensure correct use.
This manual describes the scanning method using ScandAll 21. For users using ScandAll PRO, refer to the manual, "How
to use ScandAll PRO".
CONTENTS
●
●
●
Copying of the contents of this manual in whole or in part and copying of the scanner application is
forbidden under the copyright law.
The contents of this manual are subject to change without notice.
PFU LIMITED. is not liable whatsoever for any damages resulting from use of this scanner and
procedures described in this manual, profit due to defects, and any claims by a third party.
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
Regulatory Information (1)
1
2
FCC Declaration
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
●
●
●
●
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is located.
Consult your dealer or an experienced radio/TV technician.
FCC warning:
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
ATTENTION
The use of a shielded interface cable is required to comply with the Class B limits of Part 15 of
FCC rules. The length of the AC cable must be 2 meters (6.6 feet) or less.
Canadian DOC Regulations
This digital apparatus does not exceed the Class B limit for radio noise emissions from digital apparatus set out in the
Radio interference Regulations of the Canadian Department of Communications.
This Class B digital apparatus complies with Canadian ICES-003.s
Le présent appareil numérique n'émet pas de parasites radioélectriques dépassant les limites applicables aux appareils
numériques de la classe B et prescrites dans le Règlement sur le brouillage radioélectrique dictées par le Ministère des
Communications du Canada.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Bescheinigung des Herstellers / Importeurs
Für den fi-5120C/fi-5220C wird folgendes bescheinigt:
●
●
In Übereinsstimmung mit den Bestimmungen der EN45014(CE) funkentstört
Maschinenlärminformationsverordnung 3. GPSGV: Der höchste Schalldruckpegel beträgt
70 dB (A) oder weniger, gemäß EN ISO 7779.
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
Regulatory Information (2)
1
2
International ENERGY STAR Program
As an ENERGY STAR Partner, PFU LIMITED has determined that this product meets the ENERGY STAR guidelines for energy
efficiency.
The International ENERGY STAR Office Equipment Program is an international program that promotes energy saving
through the penetration of energy efficient computers and other office equipment. The program backs the development
and dissemination of products with functions that effectively reduce energy consumption. It is an open system in which
business proprietors can participate voluntarily. The targeted products are office equipment such as computers, monitors,
printers, facsimiles, copiers, scanners, and multifunction devices.Their standards and logos are uniform among
participating nations.
Use in High-safety Applications
This product has been designed and manufactured on the assumption that it will be used in office, personal, domestic,
regular industrial, and general-purpose applications. It has not been designed and manufactured for use in applications
(simply called "high-safety applications" from here on) that directly involve danger to life and health when a high degree of
safety is required, for example, in the control of nuclear reactions at nuclear power facilities, automatic flight control of
aircraft, air traffic control, operation control in mass-transport systems, medical equipment for sustaining life, and missile
firing control in weapons systems, and when provisionally the safety in question is not ensured. The user should use this
product with adopting measures for ensuring safety in such high-safety applications. PFU LIMITED assumes no liability
whatsoever for damages arising from use of this product by the user in high-safety applications, and for any claims or
compensation for damages by the user or a third party.
About the Use of Mercury
Lamp(s) inside this product contain mercury and must be recycled or disposed of according to
local, state, or federal laws.
To avoid unexpected injury, read the following carefully.
Doing the following actions may result in serious personal injuries:
●
●
●
Do not put the substance contained in the lamp in your mouth as it has mercury.
Do not incinerate, crush, or shred the lamps or scanner parts.
Do not breathe the chemical liquid contained in the scanner lamps.
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
Trademarks
Trademarks
Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation in the United States and/or other
countries.
ISIS and QuickScan are trademarks or registered trademarks of EMC Corporation in the United States.
Adobe, the Adobe logo, and Acrobat are either registered trademarks of Adobe Systems Incorporated in the United States
and/or other countries.
Other product names are the trademarks or registered trademarks of the respective companies.
How Trademarks Are Indicated In This Manual
References to operating systems (OS) and applications are indicated as follows:
Windows 2000
Microsoft® Windows® 2000 Professional operating system
Windows XP
Microsoft® Windows® XP Professional operating system (32/64-bit),
Microsoft® Windows® XP Home Edition operating system
Windows Server 2003
Microsoft® Windows Server® 2003 Standard Edition operating system (32/64-bit)
Windows Vista
Microsoft®
Microsoft®
Microsoft®
Microsoft®
Microsoft®
Windows
Windows
Windows
Windows
Windows
Vista®
Vista®
Vista®
Vista®
Vista®
Home Basic operating system (32/64-bit),
Home Premium operating system (32/64-bit),
Business operating system (32/64-bit),
Enterprise operating system (32/64-bit),
Ultimate operating system (32/64-bit)
Where there is no distinction between the different versions of the above operating system, the general term "Windows" is
used.
Adobe Acrobat
Adobe® Acrobat ®
Where there is no distinction between the different versions of the above application, the general term "Adobe Acrobat" is
used.
The version of Adobe Acrobat provided with this product may change without notice. If the instructions described in this
manual differ from the actual displayed screen, refer to Acrobat's Help.
Manufacturer
PFU LIMITED
International Sales Dept., Imaging Bussines Division, Products Group
Solid Square East Tower, 580 Horikawa-cho, Saiwai-ku, Kawasaki-shi Kanagawa 212-8563, Japan
Phone: (81-44) 540-4538
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
Note, Liability
BEFORE USING THIS PRODUCT, PLEASE READ THIS MANUAL CAREFULLY. IF THIS PRODUCT IS NOT USED CORRECTLY,
UNEXPECTED INJURY CAN OCCUR TO USERS OR BYSTANDERS.
Keep this manual in a safe place so that it can be easily referred to during use of this product.
While all efforts have been made to ensure the accuracy of all information in this manual, PFU assumes no liability to any
party for any damage caused by errors or omissions or by statements of any kind in this manual, its updates or supplements,
whether such errors are omissions or statements resulting from negligence, accidents, or any other cause. PFU further
assumes no liability arising from the application or use of any product or system described herein; nor any liability for
incidental or consequential damages arising from the use of this manual. PFU disclaims all warranties regarding the
information contained herein, whether expressed, implied, or statutory.
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
PREFACE (1)
1
2
Safety Precautions
This manual describes important details for ensuring the safe and correct use of this product. Thoroughly read this manual
before you start to use this product. In particular, be sure to read and fully understand the Safety Precautions described in
this manual before you use this product.
Also, store this manual in a safe place so that it can be easily referred to during use of this product.
Warning Indications Used In This Manual
WARNING
This indication alerts operators to an operation that, if not strictly observed, may result
in severe injury or death.
CAUTION
This indication alerts operators to an operation that, if not strictly observed, may result
in safety hazards to personnel or damage to equipment.
Symbols Used In This Manual
This manual uses the following symbols in the explanations in addition to the warning indications.
This symbol alerts operators to particularly important information. Be sure to read this
information.
This symbol alerts operators to helpful advice regarding operation.
A TRIANGLE symbol indicates that special care and attention is required.
The drawing inside the triangle shows the specific caution.
A CIRCLE with a diagonal line inside shows action which users may not perform.
The drawing inside or under the circle shows the specific action that is not allowed.
Outline characters on a colored background show instructions users should follow.
It may also include the drawing that shows the specific instruction.
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
PREFACE (2)
1
2
Screen Examples In This Manual
The screen examples in this manual are subject to change without notice in the interest of product improvement. If the
actual displayed screen differs from the screen examples in this manual, operate by following the actual displayed screen
while referring to the User's Manual of the scanner application you are using. The screenshots in this manual were
captured from the FUJITSU TWAIN32 scanner driver, ScandAll 21 Image Capturing Utility Software, FUJITSU ISIS scanner
driver, QuickScan™ image capturing software and Adobe® Acrobat®.
Warning Label
The following picture shows the warning label used in this scanner.
High Temperature
The glass surface inside the ADF
becomes hot during the operation. Be
careful not to touch the glass surface
inside the ADF.
ATTENTION
Do NOT remove from the scanner, stain or scratch the warning labels.
About Maintenance
The user must not perform repairs on this scanner.
Contact the store where you purchased the scanner or an authorized FUJITSU Image Scanner service provider to have
repairs done on this product.
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
Safety Precautions (1)
1
2
3
4
WARNING
Do not damage the AC cable.
A damaged AC cable may cause fire or electric shock. Do not place heavy objects on AC cables, or
pull, bend, twist, heat, damage or modify AC cables.
Do not use damaged AC cables or power plugs, or install any cables or power plugs to loose wall
sockets.
Use only specified AC cables and connector cables.
Use only specified AC cables and connector cables. Failure to use the correct cables might cause
electric shock and/or equipment failure.
Please do not use the AC cable provided with this scanner for other devices, since this might cause
equipment failure and other troubles or an electric shock.
Use this scanner only at the indicated power voltage. Do not connect
to multiple-power strips.
Use this scanner only at the indicated power voltage and current. Improper power voltage and
current might cause fire or electric shock. Do not connect to multiple-power strips.
Do not touch the AC cable with wet hands.
Do not touch the power plug with wet hands. Doing so can cause electric shock.
Wipe any dust from the power plug.
Wipe off any dust from metal parts on the power plug or metal fittings with a soft, dry cloth.
Accumulated dust can cause fire or electric shock.
Do not install the device in locations that has oil smoke, steam,
humidity, and dust.
Do not install the scanner in locations subject to oil smoke, steam, humidity, and dust. Doing so
might cause a fire or electric shock.
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
Safety Precautions (2)
1
2
3
4
WARNING
Turn the scanner OFF if it is damaged.
If the scanner is damaged for any reason, turn the scanner off and unplug the power cable. Contact
the store where you purchased the scanner.
Do not use the scanner if there is a strange odor.
If you detect heat coming from the device or detect other problems such as smoke, strange smells or
noises, immediately turn off the scanner and disconnect its power plug. Make sure that any smoke
coming from it has stopped, before contacting the store where you bought the scanner or an
authorized FUJITSU scanner service provider.
Do not put liquids inside the scanner.
Do not insert or drop metal objects in to the scanner. Do not scan wet documents or documents with
paper clips or staples. Do not splash or allow the scanner to get wet.
If foreign objects (water, small metal objects, liquids, etc.) get inside the scanner, immediately turn
off the scanner and disconnect the power plug from the power outlet. Then, contact the store where
you bought the scanner or an authorized FUJITSU scanner service provider. Pay particular attention
to this warning in households where there are small children.
Do not touch the inside of the scanner unless necessary.
Do not take apart or modify the scanner. The inside of the scanner contains high-voltage
components. Touching these components might cause electric shock or fire.
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
Safety Precautions (3)
1
2
3
4
CAUTION
Do not install the scanner on unstable surfaces.
Make sure that the scanner is installed on a flat, level surface and that none of its parts extend
beyond the surface top, such as a desk or table. Do not install the scanner on unstable surfaces.
Install the scanner on a level surface that is free of vibration to prevent it from falling.
Install the scanner on a strong surface that will support the weight of the scanner and other devices.
Firmly insert the power plug.
Firmly insert the power plug as far it can go into the power outlet.
Do not block the ventilation ports.
Do not block the ventilation ports. Blocking the ventilation ports generates heat inside of scanner,
which may result in fire or scanner failure.
Do not place heavy objects or stand on top of the scanner.
Do not place heavy objects on the scanner or use the scanner's surface top to perform other work.
Improper installation might cause injuries and equipment failure.
Do not use the scanner immediately after moving it from a cold place
into a warm room.
Do not use the device immediately after moving it from a cold place into a warm room.
Condensation may occur, which might lead to scanning errors. Let the device dry about one or two
hours before you use it.
Before moving the scanner, disconnect the power plug from the power
outlet.
Do not move the scanner with the power and interface cables connected as this can damage the
cables, which can later cause fire, electric shock as well as injury.
Before moving the scanner, be sure to disconnect the power plug from the power outlet, and all
other data cables. Make sure that the floor is free of any obstructions.
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
Safety Precautions (4)
1
2
3
4
CAUTION
Protect the scanner from static electricity.
Install the scanner away from strong magnetic fields and other sources of electronic noise. Also,
protect the scanner against any static electricity, which can cause the scanner to malfunction.
Do not use aerosol sprays near the scanner.
Do not use aerosol sprays to clean the scanner. Aerosol sprays can blow dirt and dust inside the
scanner, resulting in scanner failure or malfunction.
Avoid any contact when scanner is in use.
Avoid touching any scanner mechanism during scanning since this may cause injuries.
Disconnect the power plug from the power outlet when the scanner is
not used for a long period of time.
When the scanner is not going to be used for a long period of time, be sure to disconnect the power
plug from the power outlet.
Do not install the scanner in direct sunlight.
Do not install the scanner under direct sunlight or near heating apparatus. Doing so might cause
excessive heat to build up inside the scanner, which can cause scanner trouble or even fire. Install
the scanner in a well-ventilated location.
Before moving the scanner, make sure the shipping lock is locked.
When moving the scanner, be sure to lock the shipping lock in order to prevent damages to the
scanner.
Be aware of the pick spring.
When you perform cleaning, make sure that the inside of the scanner is free of any foreign object,
and be careful not to get your hand or the cloth caught on the pick spring (metal part) as a
deformed pick spring (metal part) may cause injury.
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
Chapter 1 NAMAES AND FUNCTIONS OF PARTS
This chapter describes the scanner parts and their functions.
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
1.1 Checking the Contents of the Scanner Package
When you open the scanner package, please handle the main unit and its attachments carefully.
Make sure it contains all the parts listed in the package contents list that is included in the package box.
If any parts are missing or defective, contact the dealer were you purchased the scanner or an authorized FUJITSU
scanner service provider
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
1.2 Names and Functions of Parts (1)
1
2
3
4
This section describes the scanner parts and their functions.
Front
No.
1
2
3
4
5
6
7
Name
Function
ADF
It transports the document to the reading position automatically.
(Automatic Document Feeder)
ADF paper chute
Holds in place the document pages / sheets that are fed into the ADF.
Side Guide
It is adjusted to the width of the paper in order not to scan skewed pages.
ADF button
Puch this button to open the ADF.
This panel consists of a Function No. display, four operating push buttons
Operator panel
and a LED.
Stacker
Scanned documents are ejected from the ADF onto this tray.
Flatbed
For scanning documents not the standard sizes
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
1.2 Names and Functions of Parts (2)
1
2
3
4
Rear
No.
1
2
3
4
5
6
Name
Security Slot
Imprinter connector (fi-5120C only)
SCSI Interface connector
SCSI ID switch
USB Interface connector
DC Inlet
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
1.2 Names and Functions of Parts (3)
1
2
3
4
Inside
(for fi-5220C)
No.
1
2
3
4
Name
Document cover
Document holding pad
Document bed
Shipping lock (located on base)
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
1.2 Names and Functions of Parts (4)
1
2
3
4
Removable Parts
Parts that can be removed from the scanner are displayed below.
No.
1
2
3
4
5
Name
Document cover (fi-5220C only)
Pad ASSY
Pick roller (can be removed)
ADF paper shute
Sheet guide
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
1.3 Functions of the operator panel
The operator panel is located on the right side of the scanner. This panel comprises of a Function Number display,
four buttons and a LED.
No.
1
2
3
4
5
6
Name
Function Number display
Function Button
Send to Button
Scan Button
Power Button
LED
Function
Indicates the function Number and error status.
Changes the Function activated by the Send to button (*).
Launches the linked application software (*).
Turns the scanner ON and OFF.
Lights when the scanner is turned ON.
* About the settings on the launcher, refer to FUJITSU TWAIN32 scanner driver help.
Indications on the Function Number display
Indication
Function
8
Blinks only one time upon turning on the scanner.
P
Indicates that the scanner has been turned ON and is being initialized.
0
Indicates that initialization will soon end.
Indicates that initialization has ended successfully. The scanner is now in "Ready
1
Status".
Indicates that a temporary error occurred when documents were being scanned. A
number appearing in alternation following the U (i.e., 1 or 2, etc.) refers to the type
U
of error.
To return the scanner to the ready status ("1"), press "Scan" or "Send to" button.
Indicates that a device (hardware) alarm has occurred during scanning of
documents. "E" and the alarm Number (0 to 9, A,c,d and F) will appear alternately.
E
To return the scanner to the ready status ("1"), press "Scan" or "Send to" button. If
this alarm occurs, turn the power off and on again. If the alarm continues after
turning the power on again, contact your service engineer.
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
Chapter 2 BASIC SCANNER OPERATIONS
This chapter describes basic scanner operations.
In this chapter Windows XP screenshots are illustrated. The screens and operations may differ slightly if the OS that you
are using is other than Windows XP.
Also, when FUJITSU TWAIN32 or FUJITSU ISIS is updated the screens and operations noted in this chapter will differ slightly.
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.1Turning the Scanner ON (1)
1
2
3
4
5
6
This section describes how to turn the scanner ON.
The following shows the procedure for turning the scanner ON.
1. Press the power button on the operator panel.
The scanner is turned ON, and the green LED on the operator panel lights. Also, while the scanner is being initialized,
the indication of the Function Number display changes as follows: "8" -> "P" -> "0" -> "1" The indication "1" means
that the operator panel is in the ready status.
Power button
HINT
To turn the scanner OFF, hold the power button down for at least two seconds.
About Power ON/OFF Control
You can select to power the scanner on/off either by pressing the Power button, or by connecting / disconnecting the AC
cable.
The procedure is as follows.
1. Open Scanner's Properties.
1) When turning on the power, check that the scanner is connected to your PC.
Refer to "2.2 Connecting the Scanner to a PC in " fi-5120C / fi-5220C Getting Started".
1
2
3
4
5
6
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.1 Turning the Scanner ON (2)
1
2
3
4
5
6
2) Double click the "Printer and Other Hardware" icon on the Control panel of your PC.
The [Printer and Other Hardware] window appears.
3) On the [Printers and Other Hardware] window, double click the [Scanners and Cameras] icon.
The [Scanners and Cameras] window is displayed.
1
2
3
4
5
6
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.1 Turning the Scanner ON (3)
1
4)
2
3
4
5
6
Right click [fi-5120Cdj] or [fi-5220Cdj], and select [Properties] from the menu.
The properties dialogbox of fi-5120C or fi-5220C appears.
5)
Click the "Device Set" tab.
1
2
3
4
5
6
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.1 Turning the Scanner ON (4)
1
2
3
4
5
6
1
2
3
4
5
6
The following screen appears.
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.1 Turning the Scanner ON (5)
1
2
3
4
5
6
2. Click [Power Control] button
The following screen is displayed.
3. Select a power ON/OFF control
●
●
To power on/off the scanner by pressing the Power button:
select "Enable power switch".
To power on/off the scanner by connecting/disconnecting the AC cable:
select "Disable power switch".
1
2
3
4
5
6
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.1 Turning the Scanner ON (6)
1
2
3
4
5
6
Power Save Mode
The Power Save mode keeps the scanner in a low-powered state after it has been turned ON.
If no operation is performed on the scanner for 15 minutes, the scanner automatically switches to the Power Save mode.
In the Power Save mode, the indication of the Function Number display on the operator panel goes out, but the green LED
stays lit.
To return from the Power Save mode, perform one of the following:
●
●
●
Load the document on the ADF paper chute.
Press any button on the operator panel.
The scanner will be turned OFF when pressing down the power button for at least two seconds.
Execute a command from the scanner driver.
1
2
3
4
5
6
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.2 Loading Documents on the ADF for Scanning
(1)
1
2
3
4
1. Align the edges of the documents.
Confirm that all the documents have the same width.
Check the number of sheets in the document stack.
The standard number of sheets that can be loaded on the scanner is as follows:
(For details, see "7.3 Maximum Document Loading Capacity")
●
●
A4-size paper or smaller that makes a document stack of 5mm or less
Maximum 50 sheet at A4, 20 lb, or 80 g/m2
2. Fan the documents as follows:
Lightly grip both ends of the document with both hands, and bend the document as follows.
Firmly holding the document with both hands, bend back the document as follows so that the bent section rises
up in the middle of the document as follows.
Repeat steps 1) to 2) a few times.
Rotate the document 90 degrees, and fan again.
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.2 Loading Documents on the ADF for Scanning
(2)
1
2
3
4
3. Load the document on the ADF paper chute.
Pull out the ADF paper chute extension.
Set the documents face-down in the ADF paper chute (so that the side to be scanned faces towards the ADF
paper chute).
Load the document facing the ADF paper chute.(face down)
ATTENTION
This scanner can scan ID cards through the Automatic Document Feeder with the following
precautions.
●
●
●
●
Place one card at a time into the Auto Document Feeder.
ID card feeding requires the card to be fed through the Auto Document Feeder in
portrait mode as in the following figure.
Smooth cards should be placed face down in the Auto Document Feeder.
Embossed cards (raised lettering) should be placed with the embossed side down.
●
The card to be scanned should be within the ISO7810 compliance, type ID-1.
ISO7810-compliant, Type ID-1 card
Material:
PVC (Poly vinyl chloride) or PVCA (Polyvinyl chloride acetate)
Dimensions:
●
●
●
3.4 inch (height) x 2.1 inch (width) / 86 mm x 54 mm
0.03 ± 0.003inch / 0.76 ± 0.08mm Thickness:
Cards that are excessively rigid or less flexible may not feed smoothly and excessive
noise may occur.
Cards should be clean from oil and without labels.
Cards cannot be scanned when the imprinter is installed.
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.2 Loading Documents on the ADF for Scanning
(3)
1
2
3
4
4. Adjust the side guides to the width of the documents.
Move the side guides so that they touch both sides of the documents. If there is any space between the side guides and
the edges of documents, the scanned image may be skewed.
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.2 Loading Documents on the ADF for Scanning
(4)
1
2
3
4
HINT
The stacker prevents document sheets from dropping after they are scanned.
Lift the paper stop and swing it forward by inserting your fingertips into the indentaitons on
the scanner as shown in the figure below.
5. Start up the scanner application, and scan the document.
For details on how to scan documents using the ScandAll 21 application, refer to "2.4 Scanning Documents".
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.3 Loading Documents on the Flatbed for
Scanning
1. Lift up the document cover.
2. Load the document on the document bed with the scanning face down and the top left corner
aligned with the reference point ( ).
: Reference Point
3. Gently close the document cover.
4. Start up the scanner application, and scan the document.
For details on how to scan documents using the ScandAll 21 application, see "2.4 Scanning Documents".
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.4 Scanning Documents (1)
1
2
1. Load the document on the scanner's ADF paper chute or Flatbed.
For details on how to load documents, see "2.2 Loading Documents on the ADF for Scanning" and "2.3 Loading Documents
on the Flatbed for Scanning".
2. Start up ScandAll 21.
Select [Start] - [Program] - [Scanner Utility for Microsoft Windows] - [ScandAll 21].
This starts up ScandAll 21.
3. Select the scanner to be used.
Select [Select Source] from the [Scan] menu.
The [Select Source] dialog box appears.
Select "FUJITSU fi-5120Cdj" or "FUJITSU fi-5220Cdj" and click the [Select] button.
4. Click the [Scan To View] button on the tool bar.
The [TWAIN Driver] dialog box (screen for setting the scan conditions) appears.
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.4 Scanning Documents (2)
1
2
5. Set the scan resolution, paper size and other scan conditions, and click the [Scan] button.
For details on settings in the [TWAIN Driver] dialog box, refer to "2.5 How to Use the Scanner Driver".
The document is scanned, and an image of the scanned document appears on the ScandAll 21 screen.
For details on scanning other types of documents, refer to "Chapter 3 SCANNING VARIOUS TYPES OF DOCUMENTS".
For details on ScandAll 21 functions and operations, refer to ScandAll 21 Help.
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.5 How to Use the Scanner Driver (1)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
FUJITSU TWAIN32 Scanner Driver
FUJITSU TWAIN32 Scanner Driver is designed for scanning documents with FUJITSU image scanner fi series by using
application software that complies with the TWAIN standard.
The following describes the procedure with examples of ScandAll 21 for ordinary scanning by using this driver software.
1. Procedure for Basic Scanning Operation
Startup the application.
From the [Start] menu, select [Programs]-[Scanner Utility for Microsoft Window] and click [ScandAll 21].
Select your scanner on the window below. Select [Select Source] from the [Scan] menu.
Select the scanner to use, then click the [Select] button.
Select
●
"FUJITSU fi-5120C" or "FUJITSU fi-5220C"
1
2
3
4
5
6
7
8
9
10
11
12
13
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
14
15
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.5 How to Use the Scanner Driver (2)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Load the documents on the scanner.
For details on loading documents, refer to "2.2 Loading Documents on the ADF for Scanning".
Open the TWAIN Driver window.
Select [Scan To View] from the [Scan] menu.
HINT
ScandAll 21 provide scanning methods as follows:
●
●
●
●
●
●
[To View...]: Displays scanned images on the window.
[To File...:]: Saves scanned images as files (*.BMP, *.TIF, *.JPG).
[To FTP...:]: Transfers scanned images to a FTP server.
[To Adobe PDF...:]: Saves scanned images as PDF files.
(*Adobe Acrobat must be installed beforehand.)
[To Microsoft SharePoint Portal Server...]:
Transfers scanned images to Microsoft Share Point Portal Server.
[To Mail...]: Launches mailer software and attaches scanned images to e-mail.
For details, refer to "ScandAll 21 Help".
Configure settings for scanning and click the [Scan] button.
For details about the settings on this window, refer to "Setting Window for FUJITSU TWAIN32 Scanner Driver".
1
2
3
4
5
6
7
8
9
10
11
12
13
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
14
15
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.5 How to Use the Scanner Driver (3)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
The images of scanned documents are displayed on the [ScandAll 21] window.
Depending on the settings of the application software, images may not be displayed.
For details, refer to the documentation or Help file of your application.
e.x.) When you select [To File...] from the [Scan] menu of ScandAll 21, images of scanned documents are not displayed on
the window.
Save the scanned images.
Select [Save As...] from the [File] menu to save the scanned images.
If you wish to start another scanning, return to procedure 4.
End the application.
Select [Exit] from the [File] menu.
1
2
3
4
5
6
7
8
9
10
11
12
13
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
14
15
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.5 How to Use the Scanner Driver (4)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
2. Setting Window for FUJITSU TWAIN32 Scanner Driver
You can configure settings for the FUJITSU TWAIN32 Scanner Driver on this window.
The following describes the main setting items.
●
●
For details on each functions, refer to "FUJITSU TWAIN32 Scanner Driver Help"
(appears by pressing [Help] or [F1] button).
Depending on the type of your scanner, available setting items or range of setting values vary.
Resolution
Specifies the resolution of scanning.
It can be specified by selecting a default value from the list or customizing (specify any resolution in 1 dpi unit).
By marking the [Predefine] checkbox, you can select one from three predefined settings as [Normal], [Fine], [Super
Fine] to scan documents instead of setting details by yourself.
Otherwise, you can change the details of the predefined settings on the [Resolution Setting] window, which appears
when you click on the [...] button.
Scan Type
Specifies the feeding method, the side(s) to be scanned (Front Side, Back Side, Duplex, flatbed[fi-5220C only]) or
details of Long page (the size of documents longer than A4).
Paper Size
Selects the size of documents to be scanned from this list.
Windows for customizing the paper size will appear when you click on [...] besides the list. You can save any
document size as a customized setting (up to three) or for changing the order of the paper size in the list.
1
2
3
4
5
6
7
8
9
10
11
12
13
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
14
15
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.5 How to Use the Scanner Driver (5)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Image Mode
Specifies the image type for the scanned documents
Black & White Documents are scanned in binary (black and white).
Halftone
Documents are scanned through halftone processing in black and white.
Grayscale
Documents are scanned in gradations from black to white. For this mode you can select
256 gradations or 4 bit (16 gardations).
Color
Documents are scanned in color. For this mode, you can select 24 bit Color, 256 Color or
8 Color.
[Scan] button
Starts scanning documents with the current settings.
[Preview] button
Documents are scanned preliminarily before the actual scanning.
You can confirm the image of the documents in the preview window.
[Close] button
Saves the current settings and closes this window.
[Reset] button
Used to undo changes of settings.
[Help] button
Opens the "FUJITSU TWAIN32 Scanner Driver Help" window. The window also opens by pushing the [F1] key.
[About...] button
Opens an information window about the FUJITSU TWAIN32 Scanner Driver's version.
1
2
3
4
5
6
7
8
9
10
11
12
13
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
14
15
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.5 How to Use the Scanner Driver (6)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
[Option...] button
You can set up the details of optional functions on the window below.
[Rotation] tab
Selects this tab when setting image rotation, detection of document size, etc.
[Job/Cache] tab
Selects this tab when setting cache mode, multi feed detection, blank page skipping, etc.
[Generic] tab
Selects this tab to change the unit displayed on the Setting Window for the FUJITSU TWAIN32 Scanner Driver. (Millimeters,
Inches, and Pixels are available)
[Startup] tab
Selects this tab for setting the Scanner Operation Panel.
[Filter] tab
Selects this tab for setting the image processing filter(s).
Page Edge Filler: Fills up the margins of the scanned documents with a selected color.
Digital Endoser: A character string, such as the alphabet and numbers, can be added in the scanned document.
[Compression] tab
Selects this tab for setting the compression rate of JPEG Transfer.
[Advance...] button
Click this button for settings of the advanced image processing.
You can set Edge Extract, Gamma Pattern, White Level Follower, Dropout Color, Reverse, etc.
[Config...] button
Click this button for configuring the Setting Files.
You can save the changed settings as a Setting File. From next scanning, the settings are quickly changed by using these
Setting Files.
For details of each function, refer to the "FUJITSU TWAIN32 Scsnner Driver Help".
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.5 How to Use the Scanner Driver (7)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
FUJITSU ISIS Scanner Driver
FUJITSU ISIS Scanner Driver is designed for scanning documents with FUJITSU image scanner fi series by using application
software that complies with the ISIS standard.
The following describes the procedure with examples of QuickScan for ordinary scanning by using this driver software.
The procedure may vary depending on your application. If you use an application other than QuickScan, please refer to its
Guide or Help for further information.
1. Procedure for Basic Scanning Operation
Startup the application.
From the [Start] menu, select [Programs] - [QuickScan] and click [QuickScan].
Select your scanner on the window below.
Select [Scan] - [Select Scanner] on the menu bar.
Select the scanner to use (fi-5120C or fi-5220C) then click the [OK] button.
Select [Scan] - [New Batch] on the menu bar.
1
2
3
4
5
6
7
8
9
10
11
12
13
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
14
15
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.5 How to Use the Scanner Driver (8)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Select the profile for scanning.
●
●
●
When creating a new profile
Select one from already existing profiles and click [Add Profile...] button.
A new profile will be created based on the profile you select.
When changing the settings of already existing profiles
Select one from already existing profiles and click [Edit Profile...] button.
The settings of the selected profile can be changed.
When using an existing profile
Select one from an already existing profiles.
Scanning will be started according to the settings of the selected profile.
Go to procedure 9.
Open the window of ISIS Driver.
Select the [Scan] tab and click the [Scanner Settings] on the [Profile Editor] window.
The configuration window of FUJITSU ISIS driver appears.
15
1
2
3
4
5
6
7
8
9
10
11
12
13
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
14
15
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.5 How to Use the Scanner Driver (9)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Configure settings for scanning and click the [OK] button.
For details on this dialog box, refer to "Configuration Window of FUJITSU ISIS Scanner Driver".
The [Profile Editor] window appears. Click the [OK] button to return to [New batch] dialog.
Load the documents on the scanner.
Click the [Scan] button.
Scanned images are displayed on the window.
Refer to the "QuickScan Overview" or the "QuickScan Help" for further information on functions and operations of
QuickScan. After the installation of QuickScan, it is registered in the [Start] menu.
1
2
3
4
5
6
7
8
9
10
11
12
13
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
14
15
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.5 How to Use the Scanner Driver (10)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
2. Configuration Window of FUJITSU ISIS Scanner Driver
Image Mode
Selects a color mode suitable for the purpose from the menu.
Black & White
Scans data in binary (black and white). Distinguishes black from white according to
the fixed threshold. This scanning mode is suitable for scanning line drawings and
text documents.
16-level Grayscale
Scans data by 14 shades of gray plus black and white. This mode uses 4 bits per
pixel.
256-level
Grayscale
Scans data by 254 shades of gray plus black and white. This mode uses 8 bits per
pixel. This mode is switable for scanning monochrome photographs.
24-bit Color
Scans data as full-colored image using 24 bits per pixel. This mode is suitable for
scanning color photographs.
Image Processing
Binary processing is applied to the scanned images This mode is available only
when Image Processing Software Option (separately sold) is installed. Please refer
to the "Userfs Guide of Image Processing Software Option" for details.
Resolution
Specifies the number of pixels (dots) per inch.
Select a fixed resolution from the list or enter any value (from 50 to 600) manually. A higher resolution produces finer
image, but requires much more memory.
1
2
3
4
5
6
7
8
9
10
11
12
13
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
14
15
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.5 How to Use the Scanner Driver (11)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Halftone
Selects the halftone pattern for halftone scanning. This setting is available when "Black & White" is selected in the
"Image Mode".
Dither Pattern 0 This setting is suitable for scanning dark photographs.
Dither Pattern 1 This setting is suitable for scanning dark-colored documents containing both text and
photographs.
Dither Pattern 2 This setting is suitable for scanning light photographs.
Dither Pattern 3 This setting is suitable for scanning light-colored documents containing both text and
photographs.
Error Diffusion
This function minimizes differences of color levels due to subtractive color process by
diffusing the difference to the adjacent pixels. This mode is suitable for scanning images
of photographs, etc.
Download
Executes processing with the dithered download pattern specified in the dithered
download file.
Brightness
Sets the brightness of the entire image. Specify the brightness as a number within the range of 1 (dark) to 255 (bright).
To brighten the entire image, increase the value of the setting. To darken the entire image, decrease the value.
Contrast
Sets the contrast between light and shadow of the scanned image. Specify the contrast as a number within the range of
1 (low [soft]) to 255 (high [sharp]). Increasing this value makes the contrast sharper.
Scan Type
Selects the scanning method.
Automatic
Detects the document loaded onto the scanner and determines automatically whether to
scan from the ADF, or from the Flatbed. (fi-5220C only)
Flatbed
Scans the document placed on the flatbed. (fi-5220C only)
ADF (Front Side) Scans only the front sides of documents.
ADF (Back Side) Scans only back sides of documents.
ADF (Duplex)
Scans both front and the back sides of documents. When this option is selected, the both
sides of documents are scanned simultaneously. This option can be used only for the
models that support duplex scanning.
1
2
3
4
5
6
7
8
9
10
11
12
13
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
14
15
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.5 How to Use the Scanner Driver (12)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Paper Size
Selects a paper size according to the size of the document to be scanned. Select a standard paper size from the list.
Paper Layout
Specifies orientation of the documents as portrait or landscape.
Automatic Size and Skew detection
This option will adjust the output to the detected page size, and it will detect and automatically correct the skew of the
document.
With [Priority] slider control, you can change accuracy of Automatic Page Size Detection. Move the slider to the right
when improving the detection accuracy.
[Area...] button
Opens the Scan Area dialog box.
Specify scan area for the document size.
The size can be set by dragging the frame with mouse.
Otherwise, enter any value for the setting.
1
2
3
4
5
6
7
8
9
10
11
12
13
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
14
15
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.5 How to Use the Scanner Driver (13)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
[JPEG...] button
Opens the JPEG Settings dialog box. Used for setting the compression rate of JPEG transfer.
[About...] button
This button displays the version information.
1
2
3
4
5
6
7
8
9
10
11
12
13
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
14
15
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.5 How to Use the Scanner Driver (14)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
[More...] button
Opens [More Settings] window. Used for setting advanced features.
End of Page Detection
Scans the edge (bottom) of the documents and outputs data adjusted to the document length. When any page shorter
than specified "Paper Size" is included, the output size is adjusted to the detected short size.
Overscan
This function makes the scanned images larger than the original documents by adding margins.
Backing
With this function, the outside of document paper becomes black / white by selecting [black] / [white] background.
Gamma
Specifies Gamma correction. Correction patterns are: "Normal", "Soft", "Sharp", "Custom", or "Download".
DTC Variance
This option specifies the value for adjusting the variance based on the brightness of the image.
1
2
3
4
5
6
7
8
9
10
11
12
13
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
14
15
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
2.5 How to Use the Scanner Driver (15)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Edge Processing
This option specifies the sharpness of contour extraction.
Low, Mid, High Emphasizes contour of images. Available settings are: Low, Mid,
High
Smoothing
Smoothes jaggy images.
Dropout Color
This option excludes selected color (the three primary colors of light i.e. green, red, blue) from scanned images. For
example, if the document contains black text in a red frame and when the red color is selected, the scanner reads only the
text and eliminate (drop out) the red frame.
If you do not wish to have any colors dropped out select "None".
Reverse
Colors of scanned images are reversed.
Multi feed Detection
Detects Multi feeds (phenomena that two or more sheets are accidentally fed). You can set conditions for detecting Multi
feeds so that the scanner should stop and display error messages. Multi feeds are scanned by the differences in document
lengths or thicknesses.
1
2
3
4
5
6
7
8
9
10
11
12
13
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
14
15
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
Chapter 3 SCANNING VARIOUS TYPES OF DOCUMENTS
This chapter describes how to scan various types of documents.
In this chapter Windows XP screenshots are illustrated.
The screens and operations may differ slightly if the OS that you are using is other than Windows XP.
Also, when FUJITSU TWAIN32 or FUJITSU ISIS is updated the screens and operations noted in this chapter will differ slightly.
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.1 Scanning Double Sided Docments (1)
1
2
The following shows the procedure for reading the double sided documents.
1. Load the document on the ADF paper chute.
For details on how to load documents, see "2.2 Loading Documents on the ADF for Scanning".
Load the doccument facing the ADF paper chute (face down).
2. Adjust the side guides to the width of the documents.
3. Start up ScandAll 21.
From [Start] menu, select [Program] - [Scanner Utility for Microsoft Windows] - [ScandAll 21]. This starts up ScandAll 21.
4. Select fi-5120C or fi-5220C.
From the [Scan] menu, select [Select Source]. Then select the scanner to use and click the [Select] button.
5. Click [Scan To View] on the tool bar. The [TWAIN Driver] dialogbox appears.
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.1 Scanning Double Sided Docments (2)
1
2
6. Select [ADF (Duplex)] from [Scan Type].
7. Click the [Scan] button.
For [TWAIN Driver] dialog box setting, refer to "2.5 How to Use the Scanner Driver".
The document is scanned, and an image of the scanned document appears on the ScandAll 21 screen. For ScandAll
functions and operation, refer to [ScandAll 21 Help].
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.2 Scanning Books [fi-5220C only] (1)
1
2
CAUTION
Never look directly the light source during scanning.
1. Open the document cover.
2. Remove the document cover as shown in the figure below.
3. Read the document on the document bed face down.
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.2 Scanning Books [fi-5220C only] (2)
1
2
4. Refer to "2.4 Scanning Documents" and perform the scanning.
ATTENTION
Do not move the document during scanning.
5. When scanning ends, re-attach and gently close the document cover.
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.3 Scanning Large Documents with Flatbed [fi-5220C only]
1. Remove the document cover as shown in the figure below.
2. Load the document on the document bed face down.
3. Refer to "2.4 Scanning Documents" and perform the scanning.
ATTENTION
Do not move the document during scanning.
4. When scanning ends, re-attach and gently close the document cover.
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.4 Scanning Documents longer than A4 size (1)
2
1
3
1. Load the documents on the ADF paper chute.
For details on loading documents, refer to "2.2 Loading Documents on the ADF for Scanning".
Load the document facing the ADF paper chute. (face down)
2. Adjust the side guides to the document width.
3. Start up ScandAll 21.
For starting up ScandAll 21, select [Programs] - [Scanner Utility for Microsoft Windows] - [ScandAll 21] from [Start].
4. Select fi-5120C or fi-5220C.
From the [Scan] menu, select [Select Source]. Then select the scanner to use and click the [Select] button.
5. Click [Scan To View] on the tool bar.
The [TWAIN Driver] dialogbox appears.
1
2
3
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.4 Scanning Documents longer than A4 size (2)
1
2
3
6. Select [Long page (Front Side)] or [Long page (Duplex)] from [Scan Type].
7. Specify the length of documents and then click the [OK] button.
1
2
3
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.4 Scanning Documents longer than A4 size (3)
1
2
3
8. Click the [Scan] button.
For settings in the [TWAIN Driver] dialogbox, refer to "2.5 How to Use the Scanner Driver" .
Images of scanned documents are displayed on the window of ScandAll 21.
For details on functions and operations of ScandAll 21, refer to "ScandAll 21 Help".
1
2
3
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.5 Scanning Different-width Documents
When you scan a batch of documents with different widths by using the ADF, you may get skewed images from smaller
sized documents.
Be sure to scan only documents of the same width together.
The following shows the procedure for scanning a batch of mixed size documents.
1. Sort out the batch into stacks of the same width.
2. Adjust the side guides to the width of each document stack.
3. Scan the batches of the same widths separately one by one.
For details on how to scan documents, see "2.4 Scanning Documents".
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.6 Saving Scanned Images in PDF Format (1)
1
2
3
4
5
6
7
8
To save scanned images in PDF format, Adobe Acrobat must be installed on your PC. Adobe Acrobat can be installed from
the provided Adobe Acrobat CD-ROM.
There are 2 ways for saving scanned images in PDF format.
1. Using ScandAll 21
This method is recommended for color or grayscale scanning and when smaller PDF file size is required.
The benefits are:
●
●
Reduced PDF data size
Simplified method for creating PDF files with no troublesome operations
2. Using Adobe Acrobat
This method is recommended for faster creation of PDF files and for black and white scanning.
The benefits are:
●
●
Quick creation of PDF files with the original scan resolution
Flexibile creation of PDF files by changing the PDF compression rates
Grayscale or color scanning creates larger file sizes than black and white scanning.
If the file size is very large, you can reduce the file size by configuring the properties of Acrobat Distiller before saving
scanned images.
For details, please refer to the hints.
ATTENTION
Notes for using Adobe Acrobat
●
●
●
Acrobat's default settings overrides the previous settings for "Resolution", "Scan Type" and "Image Mode".
The following functions cannot be used:
❍
"256 Color" or "8 Color"
❍
"Rotation Degree" selection when "End of Page Detection" is selected
❍
Long Page Scanning
When scanning a paper document and converting the image to PDF using Acrobat, unexpected images
may be output when:
1. Setting "Edge Shadow Removal" in Acrobat, and setting "Digital Endorser" or "Black Background"
options in the TWAIN driver at the same time. Letter strings embedded in the image or the
background may be missed.
Solution 1: Set "Edge shadow removal" to "OFF" or set any option other than "Adaptive" for
"Color/Grayscale" and/or "Monochrome" under "Compression" by selecting [File] - [Create PDF] [From Scannerc] - [Image Settingsc] in Acrobat.
Solution 2: Adjust the scanning density in the TWAIN driver.
2. Setting "Adaptive" for "Color/Grayscale" and/or "Monochrome" under "Compression" in Acrobat
and scanning in a resolution lower than the resolution recommended for Acrobat.
Solution: Set OPTION to something other than "Adaptive" under "Compression."
3. Scanning a document longer than the double letter (11x17) or A3 size, when setting "Overscan" in
the TWAIN driver, the scan may fail.
Solution: When scanning a double letter (11x17) or A3 size of document, do not set "Overscan" in
TWAIN driver.
*As for detailed usage and information of Acrobat, refer to "Create a PDF file from a scanned document"
in Acrobat Help.
1
2
3
4
5
6
7
8
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.6 Saving Scanned Images in PDF Format (2)
1
2
3
4
5
6
7
8
Using ScandAll 21
1. Load the documents on the ADF paper chute or flatbed.
2. Start up ScandAll 21..
From [Start] menu, select [Program] - [Scanner Utility for Microsoft Windows] [ScandAll 21]. This starts up ScandAll 21.
3. From the menu bar select [Scan] and then [To Adobe PDF] from the pull down menu.
"TWAIN Driver" dialog box is displayed.
4. Select the scan resolution, document size and other scan conditions, and then click the [Scan]
button.
1
2
3
4
5
6
7
8
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.6 Saving Scanned Images in PDF Format (3)
1
2
3
4
5
6
7
8
5. To end scanning, click the [Close] button.
6. Enter the file name and select the destination to save the scanned image.
For details, refer to ScandAll 21 Help.
1
2
3
4
5
6
7
8
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.6 Saving Scanned Images in PDF Format (4)
1
2
3
4
5
6
7
8
Using Adobe Acrobat
1. Load the documents on the ADF paper chute or flatbed.
2. Start up Adobe Acrobat.
Select [All Programs] - [Adobe Acrobat] from the [Start] menu. This starts up Adobe Acrobat.
3. From the [File] menu select [Create PDF] - [From Scanner].
"Acrobat Scan Plug-in"dialog box is displayed.
4. Select "FUJITSU fi-5120Cdj or "FUJITSU fi-5220Cdj" at [Scanner] and click [Scan] button.
ATTENTION
The image may be generated in poor quality when scanning with the default settings.
It is recommended to change the settings with the following procedure.
1. Uncheck "Recognize Text Using OCR".
2. Click the [Image Settings...] button.
The "Image Settings" dialog box appears.
3. Change the following items as showing below.
●
●
●
●
Color/Grayscale: none
Monochrome: JBIG2 or CCITT Group 4
Background removal: Off
Edge shadow removal: Off
TWAIN driver" dialog box is displayed.
1
2
3
4
5
6
7
8
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.6 Saving Scanned Images in PDF Format (5)
1
2
3
4
5
6
7
8
5. Select the scan resolution, document size and other scan conditions, and click the [Scan] button.
6. To end scanning, click the [Done] button.
1
2
3
4
5
6
7
8
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.6 Saving Scanned Images in PDF Format (6)
1
2
3
4
5
6
7
8
The scanned image is displayed.
7. Select [Save as...] or [Save] from [File] menu to save the scanned image.
For the details on Adobe Acrobat operations, refer to the Adobe Acrobat manual and Help.
1
2
3
4
5
6
7
8
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.6 Saving Scanned Images in PDF Format (7)
1
2
3
4
5
6
7
8
HINT
If you save scanned documents using this procedure, the file size may increase. For reducing the file
size, please follow the procedure below. (It may take more time than usual)
1. Select [File] - [Print...].
2. On the following dialog specify [Adobe PDF] for [Name].
3. Click the [Properties] button.
4. Click the [Adobe PDF settings] tab.
1
2
3
4
5
6
7
8
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.6 Saving Scanned Images in PDF Format (8)
1
2
3
4
5
6
7
8
HINT
5. Select one from [Default Settings].
The following shows an example of [Smallest File Size].
6. Click [OK] button.
7. Enter a file name and click the [Save] button on the [Save PDF File As] dialogbox.
1
2
3
4
5
6
7
8
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.7 Excluding a Color in the Image (dropout color)
A selected color (primary colors: red, green or blue) can be removed (dropped out) from the scanned image data.
For example, if the document contains black text in a green frame, you can set the scanner to read only the text
and eliminate (drop out) the green frame.To set the scanner to drop out a color, change the settings in the [TWAIN
Driver] dialogbox before scanning.
1. Click the [Advance...] button in the [TWAIN Driver] dialogbox.
The [Advance] dialogbox appears.
2. Select the color to be drop out from [Dropout Color] under "More".
For example, if the document contains black text in green frame, select [Green] so that the scanner only reads the text
and eliminates the frames. If you do not wish to have any colors dropped out select [None].
3. Click the [OK] button.
The [TWAIN Driver] dialog box will be redisplayed. Continue scanning from this dialog box.
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.8 Skipping blank pages (1)
1
2
Change settings in the [TWAIN Driver] dialog box for skipping blank pages at scanning documents.
1. Click [Option] button in the [TWAIN Driver] dialogbox.
The [Option] dialogbox appears.
2. Click the [Job/Cache] tab.
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.8 Skipping blank pages (2)
1
2
3. Check the [Blank Page Skip] box.
If an item other than "Ram cache" or "Use Both Memory" has been selected in the [Cache Mode:] and this check box is
marked, it will change to "Ram cache".
4. With the slider control under [Blank Page Skip], specify the Blank Page Skip degree.
In Binary/Halftone mode
For white pages, use the [Black Dots Ratio] slider bar to set the skip condition. For black pages, use the [White Dots
Ratio] scroll bar to set the skip condition.
The value displayed to the right of the scroll bar displays the noise ratio(*1). If a scanned document is below this value, it
is recognized as a blank page. The setting range is OFF(- -) and 0.2% to 3.0% (in increments of 0.2%).
*1: Ratio of black dots included in the scanning area. (for white pages)
In Color/Grayscale mode
Use the slider bar to set the skip condition in five stages from 1 to 5. To make the blank pages easy to skip, increase the
value of the setting.
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.9 Detecting Multi feeds (1)
1
2
3
4
5
6
"Multi feed" is a feeding error that occurs when two or more sheets in the ADF paper chute are fed simultaneously into
the scanner.
You can set the scanner to detect multi feed, stop scanner operation, and display an error message.
To set the scanner to detect multi feed, change the settings in the [TWAIN Driver] dialogbox.
1. Click the [Option...] button in the [TWAIN Driver] dialogbox.
The [Option] dialog box appears.
2. Click the [Job/Cache] tab.
3. Select the detection conditions from "Multi Feed Detection" under "ADF Option".
1
2
3
4
5
6
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.9 Detecting Multi feeds (2)
1
3
2
4
5
6
The following detection conditions are provided:
None
Check overlapping
Multi feed detection is not performed.
The scanner monitors the overlapping of documents. The scanner detects a multi
feed by the differences in ultrasonic propagation.
Check length
The scanner monitors the length of documents. It detects a multi feed by the
differences in the document length.
Check overlapping and length: The scanner monitors both document overlapping and length to detect multi feed.
Furthermore, see " 7.5 Multi feed Detection Conditions" for detailed information about the document for multi feed
detection.
4. Click the [OK] button.
The display returns to the [TWAIN Driver] dialogbox. Continue scanning from this dialogbox.
To Specify the Area for Multi feed Detection
By default multi feed detection will monitor paper overlap over the central column (width: 35mm) of the document to be
scanned (See "Multi feed detection monitoring area" illustration on section 7.5.). This may cause to certain documents,
such as resumes and postcards which are partially pasted with photographs or stamps, to be accidently recognized as
being multi fed.
When scanning these kinds of documents, you can specify an exact detection or non-detection area (excluding the area
containing the photograph or stamp) to prevent mis-detections. The procedure is as follows.
1. Open Scanner's Properties.
1)
When turning on the power, check that the scanner is connected to your PC.
Refer to "2.2 Connecting the Scanner to a PC" in fi-5120C/fi-5220C Getting Started.
2)
Double click the "Printer and Other Hardware" icon on the Control panel of your PC.
The [Printer and Other Hardware] window appears.
1
2
3
4
5
6
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.9 Detecting Multi feeds (3)
1
2
3
4
5
6
3) On the [Printers and Other Hardware] window, double click the [Scanners and Cameras] icon.
The [Scanners and Cameras] window is displayed.
4) Right click [fi-5120Cdj] or [fi-5220Cdj], and select [Properties] from the menu.
1
2
3
4
5
6
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.9 Detecting Multi feeds (4)
1
2
3
4
5
6
The properties dialogbox of fi-5120Cdj or fi-5220Cdj appears.
5)
Click the "Device Set" tab.
The following screen appears.
1
2
3
4
5
6
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.9 Detecting Multi feeds (5)
1
2
3
4
6
5
2. Click the [Multi feed] button.
The following screen is displayed.
1
2
3
4
5
6
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.9 Detecting Multi feeds (6)
1
2
3
4
5
6
3. Specify the settings on the "Area for Multi feed Detection..." screen.
1) Mark the "Enable" check box.
HINT
●
●
You can select an area meassured from the top of the document, for which
the multi feed detection will be conducted (or not).
If you do not mark the "Enabled" checkbox, multi feed detection will monitor
the paper overlap over the central column (width: 35mm) of the document to
be scanned (For details, see the illustration "Multi feed detection monitoring
area" on section 7.5.). In this case, the settings for "Select Area to enable
Multi feed Detection" / " Select Area to disable Multi feed Detection" will not
be available.
2) Select if the Multi Feed Detection shall be applied or not for a set area.
●
To specify an area for which the Multi Feed Detection will be conducted:
check "Select area for applying Multi feed Detection."
●
To specify an area for which the Multi Feed Detection will NOT be conducted:
check "Select area for not applying Multi feed Detection."
3) Specify the "Start" of the area.
Enter the position from where the detection shall be started, meassured from the document's top edge.
(Possible values: 0 through 510mm; value of the even number)
4) Specify the "End" of the area.
Enter the position where the detection shall end, meassured from the document's top edge.
(Possible values: 0 through 510mm; value of the even number)
ATTENTION
The value for "End" must be larger than the value for "Start."
1
2
3
4
5
6
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.10 Correcting skewed documents (1)
1
2
You can set the scanner so that skew of documents are detected and corrected automatically when skewed documents are
fed into the ADF. Change the setting in the [TWAIN Driver] dialog box to enable this function. The following shows
the procedure for changing the setting in the dialogbox:
1. Click [Option] button in the [TWAIN Driver] dialogbox.
The [Option] dialog box appears.
2. Click the [Rotation] tab.
Select the [Automatic page size detection ] from the [Automatic Size and Skew Detection] menu.
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
3.10 Correcting skewed documents (2)
1
2
3. Select the [Automatic Page Size Detection] from the "Automatic Size and Skew Detection" menu.
4. Click the [OK] button.
The display returns to [TWAIN Driver] dialogbox.
HINT
With [Priority] slider control, you can change accuracy of Automatic Page Size Detection. Move
the slider to the right when improving the detection accuracy. (Note that higher accuracy setting
requires much more processing time and scanning speed becomes slower.)
ATTENTION
When using either of the following documents, the Automatic Page Size Detection may not
function correctly:
●
Paper of weight 52g/m2 or less
●
Not rectangular documents
●
Documents which their margins are filled with dark colors
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
Chapter 4 DAILY CARE
This chapter describes how to clean the scanner.
WARNING
When operating the scanner, the ADF's glass becomes very hot.
Before you clean inside the scanner, turn off its power and unplug the AC adapter from the
outlet. Wait for at least 15 minutes.
Do not turn off the scanner when you clean the Feed rollers
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
4.1 Cleaning Materials and Locations requiring Cleaning
Cleaning Materials
The table below shows the cleaning materials that are used on this scanner.
Cleaning Materials Part No.
Remarks
Cleaner F1
PA03950-0352(*1)
1 bottle (100 ml)
Moisten cloth with this fluid and wipe the scanner
clean.
Cleaning Wipe
PA03950-0419
24 sheets/pack
Pre-moistened with Cleaner F1, Cleaning Wipes are
used instead of moistened cloths.
Soft, dry cloth
Commercially available. Any lint-free cloth can be used.
*1) It may take long before the cleaner vaporizes if a large quantity is used. When cleaning the scanner
parts, dampen a cloth with modest quantities of the cleaner. In addition, wipe off the cleaner completely
with a soft lint-free cloth to leave no residue on the surface of the cleaned parts.
For details on Cleaner F1, consult the agent where you bought your scanne or an authorized FUJITSU service providerr.
Locations and Cycle for Cleaning
Location
Standard Cleaning Cycle
Pad ASSY
Pick roller
Feed roller
Plastic roller
Clean every 1,000 scanned sheets.
Glass
Document holding pad
Document bed
ATTENTION
The scanner must be cleaned more frequently when the following documents are used:
●
●
●
●
●
●
Documents of coated paper
Documents with printed text or graphics almost covering the entire surface
Chemically treated documents such as carbonless paper
Documents containing a large amount of calcium carbonate
Documents written by pencil
Documents on which the toner is not fused sufficiently
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
4.2 Cleaning the Flatbed [fi-5220C only] (1)
1
2
ATTENTION
Detergent for cleaning windows or glass cleaner can be used instead of cleaner F1. However, do not use
paint thinner or other organic solvents.
Cleaning the Flatbed
The following parts needs to be cleaned in the Flatbed area:
:Document holding pad
:Document bed
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
4.2 Cleaning the Flatbed [fi-5220C only] (2)
1
2
1. Open the document cover.
2. Clean the following locations using a soft cloth moistened with cleaner F1.
: Document holding pad.
: Document bed.
ATTENTION
●
●
Do not allow moisture to get inside the device during cleaning.
It may take long before the cleaner vaporizes if a large quantity is
used. When cleaning the scanner parts, dampen a cloth with modest
quantities of the cleaner. In addition, wipe off the cleaner completely
with a soft lint-free cloth to leave no residue on the surface of the
cleaned parts.
3. Wait for cleaned parts to dry.
4. Gently close the document cover.
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
4.3 Cleaning the ADF (1)
1
2
3
4
As a Guideline, clean the ADF every 1,000 scanned sheets. Note that this guideline varies according to the type of
documents you scan. For example, it may be necessary to clean the ADF more frequently if documents are scanned
when the toner is not sufficiently fixed on the printout.
CAUTION
●
●
The glass surface of the ADF becomes hot during the operation of the scanner.
Before you start to clean the inner parts of the scanner, disconnect the AC adapter from the
power outlet, and wait at least 15 minutes to let the glass cool down.
When you perform cleaning, make sure that the inside of the scanner is free of any foreign
object, and be careful not to get your hand or the cloth caught on the pick spring (metal part) as
a deformed pick spring (metal part) may cause injury.
Cleaning the ADF
1. Open the ADF by pushing on the ADF button and turning the ADF cover to the front.
ADF button
CAUTION
Be careful, the ADF cover may close and pinch your finger.
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
4.3 Cleaning the ADF (2)
1
2
3
4
2. Clean the following locations with a soft, dry cloth moistened with Cleaner F1.
No.
Item
1
Pad ASSY (x 1)
2
Feed rollers (x4)
3
Pick roller (x1)
4
Plastic rollers (x 4)
5
Glass (x 2)
6
Ultrasonic sensors (x 2)
ATTENTION
●
●
To avoid damaging the document sensors, take care that the cloth does not get hooked into
them when cleaning the inside of the ADF.
It may take long before the cleaner vaporizes if a large quantity is used. When cleaning the
scanner parts, dampen a cloth with modest quantities of the cleaner. In addition, wipe off the
cleaner completely with a soft lint-free cloth to leave no residue on the surface of the cleaned
parts.
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
4.3 Cleaning the ADF (3)
1
2
3
4
Pad ASSY
Wipe the pad assy downwards. When cleaning the pad assy, be careful not to get your hand or the cloth caught on the pick
spring (metal part).
Pick spring (metal part)
*Gray part
The portion to clean
Pick roller
Lightly clean the Pick roller taking care not to scratch the roller surface and the Mylar sheet. Take particular care in
cleaning this roller as black debris on it adversely affects the pickup performance.
Mylar sheet
Plastic roller
Clean lightly taking care not to damage the surface of these rollers. Take particular care when cleaning these rollers as
black debris matter on it affects document pick performance. Be careful no to damage the sponges beside the rollers.
Glass
Clean lightly.
HINT
If the glass is dirty, vertical black streaks may apper in the scanned images.
Ultra sonic sensor
Clean lightly with a dry cloth.
With the movie below, review the procedure to clean the Pad ASSY, Pick roller, ADF glass surfaces and the Plastic rollers:
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
4.3 Cleaning the ADF (4)
1
2
3
4
Feed roller
Clean lightly taking care not to roughen the surface of the rollers. Take particular care in cleaning the feed rollers since
black debris on the rollers adversely affect the pickup performance.
1. Open the ADF when the indication of the Function Number display is not "P" or "0".
If you open the ADF when the indication of the Function Number display is "P" or "0", the Feed rollers will not rotate
even you perform the operation of step 2 below.
2. Simultaneously hold down the "Send to" and "Scan" buttons on the operator panel.
The Feed rollers start to rotate slowly.
3. Hold a soft, cloth moistened with cleaning fluid against the surface of the rotating Feed rollers so that it lightly
cleans the surface of the rollers. As a guideline, seven presses of the "Send to" and "Scan" buttons make the Feed
rollers to rotate one full turn.
:Button "Send to"
:Button "Scan"
CAUTION
In step 2, all the Feed rollers turn at the same time. When cleaning the Feed rollers
positioned in the lower part of the ADF, be caereful not to touch the other Feed rollers.
With the movie below, review the procedure to clean the Feed rollers:
3. Press down on the center of the ADF to return it to its original position until the ADF button locks.
Press center of ADF
ATTENTION
When the ADF has returned to its original position, make sure that it is completely closed.
Paper jams or feeding errors may occur if the ADF is not closed completely.
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
Chapter 5 REPLACING CONSUMABLES
This chapter describes how to replace scanner consumables.
In this chapter Windows XP screenshots are illustrated.
The screens and operations may differ slightly if the OS that you are using is other than Windows XP.
Also, when FUJITSU TWAIN32 or FUJITSU ISIS is updated the screens and operations noted in this chapter will differ slightly.
WARNING
When operating the scanner, the ADFfs inside glass becomes very hot.
Before you replace the consumables, turn off its power and unplug the AC adapter from
the outlet. Wait for at least 15 minutes.
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
5.1 Consumable and Replacement Cycle (1)
1
2
3
4
The following table shows the specifications of consumables and their standard replacement cycle.
Description
P/N
Standard Replacement Cycle
PAD ASSY
PA03289-0111
50,000 sheets or one year
PA03289-0001
100,000 sheets or one year
Pick roller
The replacement cycles above are rough guidelines for the case of using A4/Letter woodfree or wood containing paper 64 g/
m2 (17 lb). This cycle varies according to the type of the used paper and how frequently the scanner is used and cleaned.
ATTENTION
Use only the consumables specified by PFU LIMITED. Do not use
consumables and parts made by other manufacturers.
To purchase the consumables, contact the FUJITSU scanner dealer where you purchased the scanner or an authorized
FUJITSU scanner service provider.
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
5.1 Consumable and Replacement Cycle (2)
1
2
3
4
Guidelines for Consumable Replacement Cycle
With this product, you can learn how many times the consumables are used so that you can estimate the right timing for
the replace
1. When turning on the power, check that the scanner is connected to the PC.
Refer to "3.2 Connecting the Scanner to a PC" in fi-5120C / fi-5220CGetting Started on the Setup CD-ROM for
information about connecting the scanner to a personal computer.
2. Double click the "Printer and Other Hardware" icon on the operator panel of the PC.
The [Printer and Other Hardware] screen is displayed.
3. In the [Printer and Other Hardware] screen, double click the "Scanners and Cameras" icon.
The [Scanners and Cameras] screen is displayed.
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
5.1 Consumable and Replacement Cycle (3)
1
2
3
4
4. Right click on "fi-5120Cdj" or "fi-5220Cdj" icon, and select [Properties] (for Windows XP), or
double click (for Windows 2000)
The properties dialogbox of fi-5120Cdj or fi-5220Cdj appears.
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
5.1 Consumable and Replacement Cycle (4)
1
2
3
4
5. Click the "Device Set" tab.
The following screen is displayed.
You can confirm the following information in this panel:
●
●
●
Total number of scans
Pad counter (approximate number of scans after resetting the pad counter)
Pick roller counter (approximate number of scans after resetting the Pick roller counter)
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
5.2 Replacing the Pad Assy (1)
1
2
1. Remove any documents on the ADF paper chute.
2. Open the ADF by pushing the ADF button.
CAUTION
Be careful, the ADF cover may close and pinch your finger.
3. Remove the Pad ASSY.
Press the knobs on both ends of the Pad ASSY, and pull the Pad ASSY upwards and towards you.
When doing this, take care not to catch the pick springs.
4. Attach the new Pad ASSY.
Hold both ends of the new Pad ASSY and attach it to its installation location.
When doing this, take care not to catch the pick springs.
ATTENTION
Make sure that the Pad ASSY is firmly attached. When the Pad ASSY is not
correctly attached, document jams or other feeding errors may occur.
5. Press down on the center of the ADF to return it into its original position.
You should hear the ADF click when it returns to its original position.
With the movie below, review the replacement procedure of the Pad ASSY:
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
5.2 Replacing the Pad Assy (2)
1
2
6. Reset the Pad Counter.
When turning on the power, check that the scanner is connected to your PC.
Open the [Scanners and Cameras] from the [Control Panel] of your PC.
Open the properties dialogbox of fi-5120Cdj or fi-5220Cdj from the [Scanners and Cameras].
The properties dialogbox of fi-5120C or fi-5220C appears.
Click the "Device Set" tab.
The following screen is displayed.
After clicking the [Clear] button beside "Pad" in "Page Counter", click the [OK] button.
The following screen is displayed.
Click the [OK] button. The Pad counter returns to "0".
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
5.3 Replacing the Pick Roller (1)
1
2
3
4
1. Remove any documents on the ADF Paper Chute.
2. Remove the ADF paper chute.
3. Open the ADF by pulling the ADF Open Lever.
ATTENTION
Be careful, the ADF may close and pinch your finger.
4. Remove the Pick roller from the scanner.
1. Grip the knobs on the sheet guide with your fingers, and lift it up to remove.
2. Rotate the Pick roller bushing in the direction of the arrow.
Pick Roller Bushing
Pick Roller Shaft
3. Remove the Pick roller while lifting it up in the direction of the arrow.
CAUTION
The Pick roller Bushing is hard. Do not turn this bearing with your fingernails.
Use a paper clip for turning the roller bushing if you can not rotate it with your finger.
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
5.3 Replacing the Pick Roller (2)
1
2
3
4
5. Remove the Pick roller from the shaft while lifting up the tab on the Pick roller.
Pull out the shaft from the pick roller while lifting up its tab.
ATTENTION
If you push up the pick roller tab using your fingernail, it may heart
or get chipped your fingernail. If you worry about that, you push up
the pick roller tab using a paper clip.
6. Attach the new Pick roller.
Insert the new Pick roller aligning the protrusion on the shaft with the slot for the screw in the Pick roller.
: Pick Roller Shaft
: Protusion
: Pick Roller
ATTENTION
Make sure that the Pick roller is completely attached. An incompletely
attached Pick roller might cause document jams or other feedings errors.
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
5.3 Replacing the Pick Roller (3)
1
2
3
4
7. Attach the Pick roller to the scanner.
Attatch the Pick roller to the scanner in reverse order of the procedure for removing.
1. Turn the Pick roller bushing in the direction indicated by the arrow.
Pick Roller Bushing
Pick Roller Shaft
2. Move the sheet guide claws in the direction indicated by the arrow to fix the sheet guide.
8. Press down the center of the ADF to return it to its original position.
You should hear the ADF click when it returns to its original position.
9. Attach the ADF paper chute.
With the movie below, review the replacement procedure of the Pick roller:
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
5.3 Replacing the Pick Roller (4)
1
2
3
4
10. Reset the Pick Roller Counter.
When turning on the power, check that the scanner is connected to your PC.
Open the [Scanners and Cameras] from the [Control Panel] of your PC.
Open the properties dialogbox of fi-5120Cdj or fi-5220Cdj from the [Scanners and Cameras].
The properties dialogbox of fi-5120C or fi-5220C appears.
Click the "Device Set" tab.
The following screen is displayed.
After clicking the [Clear] button beside "Pick Roller" in "Page Counter", click the [OK]
button.
The following screen is displayed.
Click the [OK] button. This returns the pick counter to "0".
1
2
3
4
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
Chapter 6 TROUBLESHOOTING
This chapter describes how to remedy document jams, other trouble, items to check before contacting the agent where
you bought the scanner, and how to check device labels.
ATTENTION
About troubles that are not described here, and the details of the errors, refer to the FUJITSU
TWAIN32 Scanner Driver Help.
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
6.1 Removing Jammed Documents (1)
1
2
3
If a document jam occurred, follow the procedure below to remove the jammed documents.
CAUTION
●
●
●
Take care not to get injured when removing jammed documents.
Be careful not to get neckties, necklaces, etc. entangled in the scanner when
removing the jammed documents
The surface of the glass may become hot during operation. Take care not to get
burned.
1. Remove any documents on the ADF paper chute.
2. Open the ADF by pushing on the ADF button.
ADF button
CAUTION
Be careful, the ADF cover may close and pinch your finger.
3. Remove the jammed document.
ATTENTION
●
●
Staples, paper clips, etc. cause document jams. Be sure to fully check the document
and feed path, and remove any small metal objects such as these.
Also, before you start scanning, be sure to remove any staples, clips, etc. from the
document.
Take care not to pull the pick springs when removing jammed documents.
1
2
3
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
6.1 Removing Jammed Documents (2)
1
2
3
4. Press down on the center of the ADF to return it to its original position and lock the ADF button.
Press center of ADF
ATTENTION
●
●
Make sure that the ADF is completely closed. When it is not completely closed,
document jams or feeding errors may occur.
When the scanning is completed or canceled, the documents might remain inside the
ADF even though any error message is not displayed.
Follow
1.
2.
3.
4.
the procedure below to remove the documetns remaining in the ADF.
Remove all documents from the ADF paper chute.
Open the ADF by pushing down the ADF button.
Remove the remaining documents.
Push in the center of the ADF to close it until the ADF button is locked.
1
2
3
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
6.1 Removing Jammed Documents (3)
1
2
3
If a document jam or Multi Feed errors occur frequenlty, follow the procedures below .
1. Align the edges of the document sheets.
2. Hold both the left and right sides of the document with both hands, and, as shown below, bend the
document, bring back and release one side of the stack.
3. The document edges will be slightly misaligned, as shown in the picture.
4. Load the documents into the ADF chute, as shown in the picture.
1
2
3
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
6.2 Error Indications in the Operator Panel (1)
1
2
When any error occurrs, the operator panel indicates "U" followed by a number for temporary errors or "E" followed by
a number for device alarms (permanent error). Temporary errors can be resolved by the operator, but the device
alarm requires recovery works by support engineers.
When the Error Recovery Guide is installed on your PC, its window appears when Windows is started up. If any error or
device alarm occurred, this software displays information such as error names and error codes regarding the error/
alarm. Record the information and click [Details] on its window to learn detailed information for trouble shooting.
Temporary Errors :
Indication
Meaning
Remedy
Confirm that the shipping lock is released. For
details refer toA[fi-5120C/fi-5220C Getting Start
section 2.1 Installing the Scanner].
U0
Shipping lock error(fi-5220C only)
U1
Paper Feed Error
U2
Multi Feed Error
U4
The ADF has been opened during
scanning.
U6
This is a temporary error related withthe
Imprinter option (sold separately). For details
The print cartridge is not set.(fi-5120C only)
refer to 553PR Operator's Guide, chapter "5
Error Message".
Remove the jammed documents. Refer to " 6.1
Removing JammedDocuments".
Confirm that the documents meet the paper
conditions for scanning. Refer to "7.2
Document Quality".
Close the ADF cover completely. For the
details, refer to "6 TROUBLESHOOTING".
HINT
The Error Recover Guide is stored in Setup CD-ROM. When installing the application
software, refer to "2.1 Installing the Scanner Application" in fi-5120C/fi-5220C Getting
Started.
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
6.2 Error Indications in the Operator Panel (2)
1
2
Device alarms:
Indication
Meaning
Remedy
E0
Flatbed motor malfunction.
E1
Trouble in the optical system (Flatbed).
E2
Trouble in the optical system (front).
E3
Trouble in the optical system (back).
E4
The motorfs fuse has blown out.
E6
Trouble in the operator panel.
E7
Trouble occurred in the EEPROM.
E8
The SCSI interface fuse has blown out.
E9
An error in the image memory.
EA
Trouble with the imprinter.
Ec
An alarm in the memory.
Ed
Trouble with the SCSI interface controller.
EF
Trouble with the background switching
mechanism.
1
When you encounter any alarm on the
display, turn
the scanner off and on. If the alarm is
still displayed
on the Function Number display, contact
the store
where you purchased the scanner or an
authorized
FUJITSU scanner service provider.
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
6.3 Remedying Typical Troubles
This section describes troubles that may occur during scanning and how to remedy that trouble.
Before you ask for repair, check the following flowcharts. If the remedies in these flowcharts do not solve the problem,
check the items in "6.4 Items to Check Before Contacting the Agent Where You Bought the Scanner" and then contact
the agent where you bought the scanner or an authorized FUJITSU scanner service provider.
Scanner cannot be turned On.
Indication on Function No. display goes out.
The scanning does not start.
Quality of scanned pictures or photos is not satisfactory.
Quality of scanned text of lines is unsatisfactory.
Images are distorted or blurred.
Vertical lines appear in the scanned image.
The Function No. display indicates alarm after the scanner is turned ON.
Multi feed errors occur frequently.
Pickup errors occurs frequently.
Paper jams occur frequently.
The scanned images are elongaled.
There is a shadow on the leading edge of the scanned images.
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
6.3 Remedying Typical Troubles
Symptom: Scanner cannot be turned ON.
Back
Are power cable and AC adapter correctly
connected?
Correctly connect power cable.
NO
YES
Are you using the correct AC cable and AC
adapter supplied with the scanner from the
manufacturer?
NO
You must use the AC adapter and cable
supplied with your scanner by the anufacturer.
Please get the correct AC adapter and cable to
connect to your scanner.
YES
Did you pushed the power button?
Press power button.
NO
YES
If you cannot solve the problem after taking
measures, check the items in "6.4 Items to
check before contacting the dealer where you
bought the scanner" and contact the dealer or
an authorized FUJITSU scanner service
provider .
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
6.3 Remedying Typical Troubles
Symptom: Indication on Function No. display goes out.
Back
Does the display remain blank even after you
push any button on the operator panel?
The scanner operation is normal.
NO
YES
Does the display remain blank even after
running ON the scanner again?
The scanner operation is normal.
NO
YES
If you cannot solve the problem after taking
measures, check the items in "6.4 Items to
check before contacting the dealer where you
bought the scanner" and contact the dealer or
an authorized FUJITSU scanner service
provider.
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
6.3 Remedying Typical Troubles
Symptom: The scanning does not start.
Back
Did you unlock the shipping lock of the
flatbed?
(fi-5220C only)
Turn OFF the scanner and unlock the shipping
lock. (*1)
NO
YES
Are the document loaded correctly on the ADF
paper chute?
Load document correctly on ADF paper chute.
NO
YES
Is the ADF closed completely?
Close the ADF completely.
NO
YES
Is the interface cable connected correctly?
Connect interface cable correctly. (*2)
NO
YES
Use a new interface cable and correctly
connect it.
Is the connector of interface cable broken?
YES
Yes
(when using scanner on SCSI interface)
Is the SCSI ID set correctly?
NO
Turn OFF the scanner and set the SCSI ID
correctly, then turn ON the scanner again.
(*2)
YES
Does the scanning start after running ON the
scanner again?
The scanner operation is normal.
YES
NO
If you cannot solve the problem after taking
measures, check the items in "6.4 Items to
check before contacting the dealer where you
bought the scanner" and contact the dealer or
an authorized FUJITSU scanner service
provider.
*1) For details, refer to "Getting Started" 2.1 Installing the Scanner.
*2) For details, refer to "Getting Started" 2.2 Connecting the scanner to your PC.
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
6.3 Remedying Typical Troubles
Symptom: Quality of scanned pictures or photos is not satisfactory.
Back
Did you select halftoning or dithering?
Select halftoning or dithering on your PC.
NO
YES
Are the upper/lower glasses inside the ADF,
the document bed, and the document holding
pad clean?
Clean dirty locations. (*)
NO
YES
If you cannot solve the problem after taking
measures, check the items in "6.4 Items to
check before contacting the dealer where you
bought the scanner" and contact the dealer or
an authorized FUJITSU scanner service
provider.
*)For details on how to clean dirty locations, see "Chapter 4 DAILY CARE".
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
6.3 Remedying Typical Troubles
Symptom: Quality of scanned text or lines is unsatisfactory.
Back
Are the upper/lower glasses inside the ADF,
the document bed, and the document holding
pad clean?
Clean dirty locations. (*)
NO
YES
If you cannot solve the problem after taking
measures, check the items in "6.4 Items to
check before contacting the dealer where you
bought the scanner" and contact the dealer or
an authorized FUJITSU scanner service
provider.
*)For details on how to clean dirty locations, see "Chapter 4 DAILY CARE".
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
6.3 Remedying Typical Troubles
Symptom: Images are distorted or blurred.
Back
Are the upper/lower glasses inside the ADF, the
document bed, and the document holding pad clean?
Clean dirty locations. (*)
NO
YES
Is the ADF cover pressed down or heavy object
placed on the ADF during scanning?
Do not press down the ADF or place heavy object on
the ADF during scanning.
YES
NO
Is something causing the scanner to vibrate during
scanning?
Do not allow anything to cause the scanner to
vibrate while scanning.
YES
NO
Is the scanner installed on a flat, level surface?
Install the scanner on a flat, level surface.
NO
YES
If you cannot solve the problem after taking
measures, check the items in "6.4 Items to check
before contacting the dealer where you bought the
scanner" and contact the dealer or an authorized
FUJITSU scanner service provider.
*)For details on how to clean dirty locations, see "Chapter 4 DAILY CARE".
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
6.3 Remedying Typical Troubles
Symptom: Vertical lines appear in the scanned image.
Back
Did you scan the document with the Flatbed?
(fi-5220C only)
Clean the document bed of the Flatbed. (*1)
YES
NO
Clean the upper/lower glasses inside the ADF.
(*2)
Is the glasses of the ADF Dirty?
YES
NO
Do the lines disappear on images with low
resolution settings?
Scan the documents with low resolution
settings.
YES
NO
If you cannot solve the problem after taking
measures, check the items in "6.4 Items to
check before contacting the dealer where you
bought the scanner" and contact the dealer or
an authorized FUJITSU scanner service
provider.
*1) For cleaning the Flatbed, refer to " 4.2 Cleaning the Flatbed".
*2) For cleaning the inside ADF, refer to " 4.3 Cleaning the ADF".
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
6.3 Remedying Typical Troubles
Symptom: The Function No. display indicates alarm after the scanner is
turned ON.
Back
(When the scanner is just installed on the
place) Did you unlock the shipping lock of the
flatbed?
Turn OFF the scanner and unlock the shipping
lock, then turn ON the scanner again.(*)
NO
YES
Does the Function No. display indicate any
alarm after turning ON the scanner again?
The scanner operation is normal.
NO
YES
If you cannot solve the problem after taking
measures, check the items in "6.4 Items to
check before contacting the dealer where you
bought the scanner" and contact the dealer or
an authorized FUJITSU scanner service
provider.
*) For details, refer to "Getting Started" 2.1 Installing the Scanner.
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
6.3 Remedying Typical Troubles
Symptom: Multi feed errors occur frequently.
Back
Do the documents satisfy the conditions
described in "7.2 Document Quality"?
Use documents that satisfy the requirements.
(*1)
NO
YES
When the multi feed detection is ON, are the
multi feed detection conditions satisfied?(*2)
Satisfy the multi feed detection conditions. (*2)
NO
YES
Were the documents fanned before loaded
onto the ADF paper chute?
Fan the document before loading, or reduce
the number of sheets of the documents.
NO
YES
Have you scanned a very thick paper or plastic
document?
When scanning documents like this, disable
the multifeed detection.
YES
NO
Have the documents just been printed out on a
copier or laser printer?
Fan the documents 3 or 4 times to remove
static electricity from the paper.
YES
NO
Reduce the number of sheets of the document.
(*3)
Is the document stack 5 mm or less?
NO
YES
Are all the consumables (Pick roller and Pad
ASSY) installed correctly?
Correctly install the consumables if needed.
NO
YES
Is any of consumables (Pick roller and Pad
ASSY) dirty?
Clean the dirty consumables.(*4)
YES
NO
Is any of consumables (Pick roller and Pad
ASSY) worn out? (Check the consumable
counter)
Replace the consumable, if needed. (*5)
YES
NO
If you cannot solve the problem after taking
measures, check the items in "6.4 Items to
check before contacting the dealer where you
bought the scanner" and contact the dealer or
an authorized FUJITSU scanner service
provider.
*1)For
*2)For
*3)For
*4)For
*5)For
details
details
details
details
details
on
on
on
on
on
requirements, see "7.2 Document Quality".
multi feed, see "7.5 Multi feed Detection Conditions".
requirements, see "7.3 Maximum Document Loading Capacity".
how to clean the consumables, see "4.3 Cleaning the ADF".
how to replace and attach consumables, see "5 REPLACING CONSUMABLES".
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
6.3 Remedying Typical Troubles
Symptom: Pickup errors occurs frequently.
Back
Do the documents satisfy the conditions
described on "7.2 Document Quality"?
Use documents that satisfy the quirements.
(*1)
NO
YES
Were the documents fanned before loading on
ADF paper chute?
Fan the document before loading, or reduce
the number of sheets of the documents.
NO
YES
Are all the consumables (Pick roller and Pad
ASSY) installed correctly?
Correctly install the consumable(Pick roller and
Pad ASSY), if needed. (*2)
NO
YES
Is any of consumables (Pick roller, Pad ASSY)
dirty?
Clean the dirty consumable. (*3)
YES
NO
Is any of consumables (Pick roller and Pad
ASSY) worn out? (Check the consumable
counter)
Replace the consumable, if needed. (*4)
YES
NO
If you cannot solve the problem after taking
measures, check the items in "6.4 Items to
check before contacting the dealer where you
bought the scanner" and contact the dealer or
an authorized FUJITSU scanner service
provider.
*1)
*2)
*3)
*4)
For
For
For
For
details
details
details
details
on
on
on
on
requirements, see "7.2 Document Quality".
how to install the consumables, see "5 REPLACING CONSUMABLES".
how to clean the consumables, see "4.3 Cleaning the ADF".
how to replace the consumables, see "5 REPLACING CONSUMABLES".
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
6.3 Remedying Typical Troubles
Symptom: Paper jams occur frequently.
Back
Do the documents satisfy the conditions
described on "7.2 Document Quality"?
Use documents that satisfy the quirements.
(*1)
NO
YES
Clean the ADF or remove debris from the ADF.
(*2)
Is there any debris in the ADF?
YES
NO
Are all the consumables (Pick roller and Pad
ASSY) installed correctly?
Correctly install the consumables (Pick roller
and Pad ASSY), if needed. (*3)
NO
YES
Is any of consumables (Pick roller, Pad ASSY)
dirty?
Clean the dirty consumable. (*2)
YES
NO
Is any of consumables (Pick roller and Pad
ASSY) worn out? (Check the consumable
counter)
Replace the consumable, if needed. (*3)
YES
NO
If you cannot solve the problem after taking
measures, check the items in "6.4 Items to
check before contacting the dealer where you
bought the scanner" and contact the dealer or
an authorized FUJITSU scanner service
provider.
*1) For details on requirements, see "7.2 Document Quality".
*2) For details on how to clean the ADF, see "4.3 Cleaning the ADF".
*3) For details on how to attach the consumables, see "5 REPLACING CONSUMABLES".
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
6.3 Remedying Typical Troubles
Symptom: The scanned images are elongated
Back
Have you cleaned all the rollers?
Clean all the rollers. (*)
NO
YES
Have you adjusted the scan scale?
YES
Check the items in "6.4 Items to check before
contacting the dealer where you bought the
scanner" and contact the dealer or an
authorized FUJITSU scanner service provider.
NO
Set the scan scale.
Display the properties of the scanner that you
are
using on "Scanners and Cameras" in the
control
panel, then adjust the scan scale.
*) For details on how to clean the rollers, see "4.3 Cleaning the ADF".
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
6.3 Remedying Typical Troubles
Symptom: There is a shadow on the leading edge of the scanned images.
Back
Did you adjust the offset (starting position for
scanning the document)?
YES
Check the items in "6.4 Items to check before
contacting the dealer where you bought the
scanner" and contact the dealer or an
authorized FUJITSU scanner service provider..
NO
Adjust the offset.
Display the properties of the scanner that you
are
using on "Scanners and Cameras" in the
control
panel, then adjust the [Sub-scan Setting].
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
6.4 Items to Check Before Contacting the Agent Where You Bought
the Scanner
Check the following items before you contact the dealer where you bought the scanner.
Print
General Details
Item
Model
Serial No.
findings
(Example) fi-5120C
For details on model, see "6.5 Checking Labels on the Scanner".
(Example) 000001
For details on serial No., see "6.5 Checking Labels on the Scanner".
2006
Production date
Date of purchase
Symptom
Frequency of trouble
Total number of scanned page
(ADF)
Year 1
Month 1
2006-05 (May, 2006)
For details on production date, see "6.5 Checking Labels on the Scanner".
2006
Year 1
Month 1
Installation or PC connection issues
Problem at the time of personal computer connection
Item
OS
iWindowsj
findings
Windows Vista
Displayed
error
message
Application
(Example) SCSI interface
Interface
controllers (Example) made by Adaptec
SCSI Card 2940AU
Feed system trouble
Item
findings
Document type
Main purpose of use
Last cleaning date
2006
Year 1
Month 1
Last consumables
replacement date
2006
Year 1
Month 1
Operator panel status at
trouble
Imaging system trouble
Item
findings
Type and
version of
scanner
driver
Type of
interface
controller
OS
(Windows)
(Example) made by Adaptec
SCSI Card 2940AU
Windows Vista
Application
software
(Example) ScandAll 21, Acrobat
Other
Item
findings
Can both the original document and scanner image be sent by e-mail or Fax?
Print
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
available
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
6.5 Checking Labels on the Scanner
This section describes how to check the labels on the scanner.
Positions of Labels on the Scanner
The following shows where the two labels are located on the scanner.
Label A (example): Indicates scanner information.
Label B (example): Indicates various standards that the scanner conforms with.
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
Chapter 7 ADF AND PAPER SPECIFICATION
This chapter describes the required document size and paper quality for ensuring correct operation when scanning
documents on the ADF.
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
7.1 Document Size
The following shows the size of documents that can be scanned on the ADF.
Maximum
A
216 (8.5 in)
Minimum
B
356 (14 in)
A
53 (2.1 in)
B
74 (2.9 in)
(Unit:mm)
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
7.2 Document Quality (1)
1
2
Document Type
The following paper types are recommended for document use:
●
●
Woodfree paper
Wood containing paper
When using documents of paper type other than the above, check whether or not the document can be scanned by testscanning a few sheets before executing the actual document.
Document Thickness
Paper thickness is expressed by "paper weight." The following shows the paper weights that can be used on this scanner:
●
52 g/m2`127 g/m2
Only paper weight of 127 g/m2 is acceptable for A8-size documents.
Precautions
The following documents may not be scanned successfully:
●
●
●
●
●
●
●
●
●
●
●
●
Documents of non-uniform thickness (e.g. envelopes and documents with photographs attached)
Wrinkled or curled documents (See HINT below.)
Folded or torn documents
Tracing paper
Coated paper
Carbon paper
Carbonless paper
Photosensitive paper
Perforated or punched documents
Documents that are not square or rectangular
Very thin documents
Photographs
Do not use the following documents:
●
●
●
●
●
Paper-clipped or stapled documents
Documents on which the ink is still wet
Documents smaller than A8 (Portrait) in size
Documents wider than A4 or Letter size (216mm)
Documents other than paper such as fabric, metal foil, or transparencies
HINT
●
●
When scanning semi-transparent documents, slide the [Brightness] bar to light to avoid bleed
through.
To prevent the rollers from becoming dirty, avoid scanning documents containing large areas
written or filled in pencil. If scanning of such documents is unavoidable, clean the rollers frequently.
ATTENTION
●
Carbonless paper contains chemical substances that may damage the Pad ASSY or rollers (e.g. Pick
roller) when documents are fed. Pay attention to the following:
Cleaning:
If pick errors occur frequently, clean the Pad ASSY and Pick rollers.
For details on cleaning the Pad ASSY and Pick rollers, see "4.3 Cleaning the ADF".
●
●
●
Replacing parts:
The service life of the Pad ASSY and Pick rollers is sometimes shortened when scanning mediumgrade paper documents.
If paper containing wood is scanned, the service life of the Pad and Pick roller may become shorter
than that of the Pad and Pick roller used for scanning only woodfree paper.
The pad or rollers of the scanner could be damaged if photographs or sheets of paper attached to
the scanned document have contact with the pad or rollers during scanning.
Scanning documents of calendered paper such as photographs may damage the surface of them.
HINT
When using the ADF, the leading edge of all document sheets must be evenly aligned. Make sure that
curling at the leading edge is within the following tolerances:
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
7.2 Document Quality (2)
1
2
ATTENTION
This scanner can scan ID cards through the Automatic Document Feeder with the following precautions.
●
●
●
●
●
Place one card at a time into the Auto Document Feeder.
ID card feeding requires the card to be fed through the Auto Document Feeder in portrait mode as in
the following figure.
Smooth cards should be placed face down in the Auto Document Feeder.
Embossed cards (raised lettering) should be placed with the embossed side down.
The card to be scanned should be within the ISO7810 compliance, type ID-1.
ISO7810-compliant, Type ID-1 card
Material:
PVC (Poly vinyl chloride) or PVCA (Polyvinyl chloride acetate)
Dimensions:
●
●
●
3.4 inch (height) x 2.1 inch (width) / 86 mm x 54 mm
0.03 ± 0.003inch / 0.76 ± 0.08mm Thickness:
Cards that are excessively rigid or less flexible may not feed smoothly and excessive noise may
occur.
Cards should be clean from oil and without labels.
Cards cannot be scanned when the imprinter is installed.
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
7.3 Maximum Document Loading Capacity
The maximum number of sheets that can be loaded on the ADF paper chute is determined by the size and weight of
the document. The following graph shows the maximum document loading capacity of ADF according to paper weight.
Unit
g/m2
lb
kg
52
14
45
64
17
55
75
20
64.5
Conversion
80
90
21
24
69
77.5
104
28
90
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
127
34
110
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
7.4 Area not to be perforated
When using the ADF, document trouble might occur if there are punched holes in the shaded area in the following figure.
If hole-punched documents must be scanned, use the Flatbed.
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
7.5 Multi feed Detection Conditions (1)
1
2
There are three multi feed detection modes: document overlapping, document length, and both document thickness
and length. The following conditions must be satisfied in each of these detection modes.
Detection by Document Overlapping
Sheets of the same thickness shall be set in the ADF at a time.
●
●
●
Document thickness: 0.065 to 0.15mm
Punched holes are not allowed within 35mm of the vertical center line of the document.
Other paper shall not be glued within 35 mm (1.4 in) of the vertical centerline of the document.
Detection by Document Length
Sheets of the same length shall be set in the ADF at a time.
●
●
Document length deviation: 1% or less
Punched holes are not allowed within 35mm of the vertical center line of the document.
Detection by Document Overlapping and Length
Sheets of the same thickness and length shall be set in the ADF at a time.
●
●
●
●
Document thickness: 0.065 to 0.15mm
Document length deviation: 1% or less
Punched holes are not allowed within 35mm of the vertical center line of the document.
Other paper shall not be glued within 35 mm (1.4 in) of the vertical centerline of the document.
ATTENTION
Multifeed detection by overlap will often mis-detect very thick paper or plastic document.
When scanning documents like this, please disable the multifeed detection.
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
7.5 Multi feed Detection Conditions (2)
1
2
HINT
The type of document and document conditions sometimes cause the multi feed detection
rate to drop.
Multi feed detection monitoring area
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
Chapter 8 SCANNER SPECIFICATION
This chapter lists the scanner specifications.
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
8.1 Basic Specifications
No.
Item
Specification
Notice
1
Scanner Type
fi-5120C: ADF(Automatic Document Feeder)
fi-5220C: ADF + Flatbed
2
Image sensor
fi-5120C: CCD x 2
fi-5220C: CCD x 3
fi-5120C: Front / Back
fi-5220C: Front / Back /
Flatbed
3
Light source
White cold cathode fluorescent lamp:
x 2 (fi-5120C)
x 3 (fi-5220C)
fi-5120C: Front / Back
fi-5220C: Front / Back /
Flatbed
4
Scanning Minimum
area
A8 (Portrait)
ADF 127 g/m2 paper
(Note (*1))
Maximum
ADF: Legal
(Long page scanning: 216 x 864mm or
(Note (*2))
8.50 x 34in)
Flatbed (fi-5220C): 216 x 297mm (8.50 x 11.69in)
5
Paper Weight
52 g/m2 to 127g/m2 (14 to 34lb)
(Note (*3))
6
Scanning Binary
Speed
(monochrome)
(A4
Portrait) Color
(Note
(*4))
Simplex: 25 sheets/min.
Duplex: 50 sides/min.
200 dpi (Note (*5))
Simplex: 30 sheets /min.
Duplex: 60 sides/min.
150 dpi (Note (*5))
7
Capacity of ADF
50 sheets
A4, 80 g/m2 (20lb) (Note
(*6))
8
Optical Resolution
600 dpi
-
9
Output
Binary
50 ~ 600 dpi
resolution (monochrome)
Scalable in 1 dpi
increments
Grayscale
50 ~ 600 dpi
Scalable in 1 dpi
increments
Color
50 ~ 600 dpi
Scalable in 1 dpi
increments
10
Grayscale level
(internal)
8 bits per color
Internal 10 bits
11
Halftone Patterns
Dither / error diffusion
-
12
Interface
(Note (*7))
Ultra SCSI
Shield-type 50 pin (pintype) halfpich
USB2.0 / 1.1 (Note(*8))
B type
JPEG compression
-
Imprinter Port (fi-5120C only)
-
13
Other function
*1
The minimum size for scanning is A8 when using the ADF. When using the Flatbed (fi-5220C only) to scan the
minimum scanning range is virtually unlimited.
*2
When scanning a "long page", if Automatic Page Size Detection is enabled, the maximum scanning length will be
reduced by an overscan margin.
(Automatic Page Size Detection will overscan (scan at a slightly larger size) the document, which will result in
some part of the document to be left out.)
*3
The document's thicknesses noted are for when using the ADF. When using the Flatbed to scan the document's
thickness is unlimited.
For details, see "Chapter7 ADF AND PAPER SPECIFICATION".
*4
The scanning speed is the maximum speed of the scanner hardware. Software processing time such as data
transfer time is added to the actual scanning time.
*5
The scanning speed noted is the value when using the ADF to scan.
*6
The maximum stacking capacity varies according to the document thickness. For details, see "Chapter7 ADF AND
PAPER SPECIFICATION".
*7
The Ultra SCSI and USB 2.0 / 1.1 interfaces cannot be used at the same time.
*8
If you connect the scanner with USB 2.0, it is required that the USB port and the Hub are compliant with USB 2.0.
The scanning speed may slow down when you connect the scanner with USB 1.1. If your omputer has the
compatible USB 2.0 port, please use it.
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
8.2 Installation Specifications
Item
Specification
Dimensions (mm)
(fi-5120C: Without ADF paper
chute)
Depth
Width
Height
fi-5120C: 168 mm
(6.6 in)
fi-5220C: 569 mm
(22.4 in)
fi-5120C: 301 mm
(11.8 in)
fi-5220C: 302 mm
(11.9 in)
fi-5120C: 158 mm
(6.2 in)
fi-5220C: 229 mm
(9.0 in)
Installation Space (mm)
(D x W x H)
Depth
Width
Height
fi-5120C: 700 mm
(27.6 in)
fi-5220C: 800 mm
(31.5 in)
fi-5120C: 400 mm
(15.8 in)
fi-5220C: 400 mm
(15.8 in)
fi-5120C: 380 mm
(15.0 in)
fi-5220C: 450 mm
(17.8 in)
Weight (kg)
fi-5120C: 3.8 (8.39lb)
fi-5220C: 8.4 (18.54 lb)
Input power
Voltage
AC100V ~ 120V, ±10%
AC220V ~ 240V, ±10%
Phases
Single-phase
Frequency
50/60 ±3 Hz
Power consumption
fi-5120C: 33 W or less
fi-5220C: 38 W or less
ATTENTION
Installation Space is the reference value of an installation space required to read A4 size documents.
Item
Ambient condition
Specification
Device status
Operating
Not operating
Temperature
5 to 35 ºC (41 to 95ºF)
-20 to 60 ºC (-4 to 140ºF)
Humidity
20 to 80 %
8 to 95 %
Calorific value
fi-5120C: 28.38 kcal/H or less
fi-5220C: 32.78 kcal/H or less
Shipping Weight (kg)
fi-5120C: 5.3 (11.7 lb)
fi-5220C: 11.9 (26.27 lb)
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
8.3 External Dimensions
The following shows the external dimensions:
fi-5120C
fi-5220C
(Unit:mm)
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
APPENDIX 1 Before using the [Scan] or the [Send to] button
(1)
1
2
By setting the link of the application software to the [Scan] or [Send to] button, you can launch the linked application
by simply pushing the button.
1. Select [Start]-[Control Panel].
2. Select [Scanners and Cameras]-[Properties].
3. Select the [Events] tab.
4. Select an Event. For Windows XP, select the event for starting up any application from the [Select
an event] menu.
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED
fi-5120C / fi-5220C Image Scanner Operator
Guide
TROUBLE SHOOTING
CONTENTS MAP
TOP
APPENDIX 1 Before using the [Scan] or the [Send to] button
(2)
1
2
The events available for this function are:
●
●
Scan button (When pushing the [Scan] button)
Send to 1-9 (When pushing the [Send] to button)
5. Select the application with its process, excuted by the event. For Windows XP, click [Start this
program] under [Actions] and select the application and process from the menu.
6. Click [OK] button.
HINT
The window and operations may vary depending on your OS.
1
2
All Rights Reserved Copyright 2006-2009 © PFU LIMITED