BL01292-200
DIGITAL CAMERA
FINEPIX HS20EXR
Owner’s Manual
Thank you for your purchase of this
product. This manual describes how
to use your FUJIFILM FinePix HS20EXR
digital camera and the supplied software. Be sure that you have read and
understood its contents before using
the camera.
EN
Before You Begin
First Steps
Basic Photography and Playback
More on Photography
More on Playback
Movies
Connections
For information on related products, visit our website at
http://www.fujifilm.com/products/digital_cameras/index.html
Menus
Technical Notes
Troubleshooting
Appendix
For Your Safety
IMPORTANT SAFETY INSTRUCTIONS
• Read Instructions: All the safety and
operating instructions should be
read before the appliance is operated.
• Retain Instructions: The safety and
operating instructions should be
retained for future reference.
• Heed Warnings: All warnings on the
appliance and in the operating instructions should be adhered to.
• Follow Instructions: All operating
and use instructions should be followed.
Installation
Power Sources: This video product
should be operated only from the
type of power source indicated on
the marking label. If you are not sure
of the type of power supply to your
home, consult your appliance dealer
or local power company. For video
products intended to operate from
battery power, or other sources, refer
to the operating instructions.
Grounding or Polarization: This video
product is equipped with a polarized alternating-current line plug (a
plug having one blade wider than
the other). This plug will fit into the
power outlet only one way. This is a
safety feature. If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should
still fail to fit, contact your electrician
to replace your obsolete outlet. Do
ii
not defeat the safety purpose of the This video product should never be
placed near or over a radiator or heat
polarized plug.
register.
Alternate Warnings: This video
product is equipped with a 3-wire Attachments: Do not use attachments
grounding-type plug, a plug having not recommended by the video
a third (grounding) pin. This plug will product manufacturer as they may
only fit into a grounding-type power cause hazards.
outlet. This is a safety feature. If you
Water and Moisture: Do not use this
are unable to insert the plug into
video product near water – for exthe outlet, contact your electrician
ample, near a bath tub, wash bowl,
to replace your obsolete outlet. Do
kitchen sink, or laundry tub, in a wet
not defeat the safety purpose of the
basement, or near a swimming pool,
grounding-type plug.
and the like.
Overloading: Do not overload wall
Power-Cord Protection: Power-Supoutlets and extension cords as this
ply cords should be routed so that
can result in a risk of fire or electric
they are not likely to be walked on
shock.
or pinched by items placed upon
Ventilation: Slots and openings in the or against them, paying particular
cabinet are provided for ventilation attention to cords at plugs, conveand to ensure reliable operation of nience receptacles, and the point
the video product and to protect it where they exit from the appliance.
from overheating, and these openAccessories: Do not place this video
ings must not be blocked or covproduct on an unstable cart, stand,
ered.
tripod, bracket, or table. The video
The openings should never be
product may fall, causing serious inblocked by placing the video prodjury to a child or adult, and serious
uct on a bed, sofa, rug, or other simidamage to the appliance. Use only
lar surface.
with a cart, stand, tripod, bracket, or
This video product should not be
table recommended by the manuplaced in a built-in installation such
facturer, or sold with the video prodas a bookcase or rack unless proper
uct. Any mounting of the appliance
ventilation is provided or the manshould follow the manufacturer’s inufacturer’s instructions have been
structions, and should use a mountadhered to.
ing accessory recommended by the
manufacturer.
An
appliance
and cart combination should
be moved with
care. Quick stops,
excessive force,
and uneven surfaces may cause the appliance and
cart combination to overturn.
Antennas
Outdoor Antenna Grounding: If an
outside antenna or cable system is
connected to the video product, be
sure the antenna or cable system
is grounded so as to provide some
protection against voltage surges
and built-up static charges. Section
810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with respect to proper grounding
of the mast and supporting structure, grounding of the lead-in wire
to an antenna-discharge unit, size of
grounding conductors, location of
antenna-discharge unit, connection
to grounding electrodes, and requirements for the grounding electrode.
For Your Safety
Power Lines: An outside antenna system should not be located in the
vicinity of overhead power lines or
other electric light or power circuits,
or where it can fall into such power
lines or circuits. When installing an
outside antenna system, extreme
care should be taken to keep from
touching such power lines or circuits
as contact with them might be fatal.
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
Ground Clamp
Electric
Service
Equipment
Ground
Clamps
Power Service
Grounding Electrode
System (NEC ART 250.
PART H)
Antenna
Lead in Wire
Antenna
Discharge Unit
(NEC SECTION
810-20)
Grounding
Conductors
(NEC SECTION
810-21)
Use
Cleaning: Unplug this video product
from the wall outlet before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth
for cleaning.
Object and Liquid Entry: Never push
objects of any kind into this video
product through openings as they
may touch dangerous voltage
points or short out parts that could
result in a fire or electric shock. Never
spill liquid of any kind on the video
product.
Lightning: For added protection for
this video product receiver during
a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna
or cable system. This will prevent
damage to the video product due to
lightning and power-line surges.
Replacement Parts: When replacement parts are required, be sure
the service technician has used
replacement parts specified by the
manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may
result in fire, electric shock or other
Damage Requiring Service: Unplug this hazards.
video product from the wall outlet
and refer servicing to qualified ser- Safety Check: Upon completion of any
vice personnel under the following service or repairs to this video product, ask the service technician to
conditions:
When the power-supply cord or perform safety checks to determine
that the video product is in proper
plug is damaged.
If liquid has been spilled, or objects operating condition.
have fallen into the video product.
If the video product has been exposed to rain or water.
If the video product has been
dropped or the cabinet has been
damaged.
If the video product does not operate normally be following the
operating instructions. Adjust only
those controls that are covered by
the operating instructions as an improper adjustment of other controls
may result in damage and will often
require extensive work by a qualified
technician to restore the video product to its normal operation.
When the video product exhibits a
distinct change in performance - this
indicates a need for service.
Service
Servicing: Do not attempt to service
this video product yourself as opening or removing covers may expose
you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
iii
For Your Safety
Be sure to read this notes before using
Safety Notes
• Make sure that you use your camera correctly. Read these Safety Notes and
your Owner’s Manual carefully before use.
• After reading these Safety Notes, store them in a safe place.
WARNING
Do not allow water or foreign objects to enter the camera.
If water or foreign objects get inside the camera, turn the camera
off, remove the battery and disconnect and unplug the AC power
Avoid
adapter.
exposure to
Continued use of the camera can cause a fire or electric shock.
water
• Contact your FUJIFILM dealer.
About the Icons
The icons shown below are used in this document to indicate the severity of
the injury or damage that can result if the information indicated by the icon
is ignored and the product is used incorrectly as a result.
WARNING
CAUTION
This icon indicates that death or serious injury can result if the information is ignored.
This icon indicates that personal injury or material damage can result
if the information is ignored.
The icons shown below are used to indicate the nature of the information
which is to be observed.
Triangular icons tell you that this information requires attention (“important”).
Circular icons with a diagonal bar tell you that the action indicated is
prohibited (“Prohibited”).
Filled circles with an exclamation mark tell you an action that must be
performed (“Required”).
WARNING
If a problem arises, turn the camera off, remove the battery, disconnect and
unplug the AC power adapter.
Continued use of the camera when it is emitting smoke, is emitting
Unplug
any unusual odor, or is in any other abnormal state can cause a fire
from power
or electric shock.
socket.
• Contact your FUJIFILM dealer.
iv
Do not use in
the bathroom
or shower.
Do not disassemble
Do not use the camera in the bathroom or shower.
This can cause a fire or electric shock.
Never attempt to disassemble or modify (never open the case).
Failure to observe this precaution can cause fire or electric shock.
Should the case break open as the result of a fall or other accident, do not
touch the exposed parts.
Failure to observe this precaution could result in electric shock or in
Do not touch injury from touching the damaged parts. Remove the battery iminternal
mediately, taking care to avoid injury or electric shock, and take the
parts
product to the point of purchase for consultation.
Do not change, heat or unduly twist or pull the connection cord and do not
place heavy objects on the connection cord.
These actions could damage the cord and cause a fire or electric
shock.
• If the cord is damaged, contact your FUJIFILM dealer.
Do not place the camera on an unstable surface.
This can cause the camera to fall or tip over and cause injury.
Never attempt to take pictures while in motion.
Do not use the camera while you are walking or driving a vehicle. This
can result in you falling down or being involved in a traffic accident.
Do not touch any metal parts of the camera during a thunderstorm.
This can cause an electric shock due to induced current from the
lightning discharge.
Do not use the battery except as specified.
Load the battery as aligned with the indicator.
For Your Safety
WARNING
Do not heat, change or take apart the battery. Do not drop or subject the battery to impacts. Do not store the battery with metallic products. Do not use
chargers other than the specified model to charge the battery.
Any of these actions can cause the battery to burst or leak and cause
fire or injury as a result.
Use only the battery or AC power adapters specified for use with this camera.
Do not use voltages other than the power supply voltage shown.
The use of other power sources can cause a fire.
If the battery leaks and fluid gets in contact with your eyes, skin or clothing.
Flush the affected area with clean water and seek medical attention or call an
emergency number right away.
Do not use the charger to charge batteries other than those specified here.
The Ni-MH battery charger is designed for FUJIFILM HR-AA Ni-MH
batteries. Using the charger to charge conventional batteries or other
types of rechargeable batteries can cause the battery to leak fluid,
overheat or burst.
When carrying the battery, install it in a digital camera or keep it in the hard
case. When storing the battery, keep it in the hard case. When discarding,
cover the battery terminals with insulation tape.
Contact with other metallic objects or battery could cause the battery to ignite or burst.
Keep Memory Cards out of the reach of small children.
Because Memory Cards are small, they can be swallowed by children.
Be sure to store Memory Cards out of the reach of small children. If
a child swallows a Memory Card, seek medical attention or call an
emergency number.
CAUTION
CAUTION
Do not place heavy objects on the camera.
This can cause the heavy object to tip over or fall and cause injury.
Do not move the camera while the AC power adapter is still connected. Do not
pull on the connection cord to disconnect the AC power adapter.
This can damage the power cord or cables and cause a fire or electric
shock.
Do not use the AC power adapter when the plug is damaged or the plug socket
connection is loose.
This could cause a fire or electric shock.
Do not cover or wrap the camera or the AC power adapter in a cloth or blanket.
This can cause heat to build up and distort the casing or cause a fire.
When you are cleaning the camera or you do not plan to use the camera for
an extended period, remove the battery and disconnect and unplug the AC
power adapter.
Failure to do so can cause a fire or electric shock.
When charging ends, unplug the charger from the power socket.
Leaving the charger plugged into the power socket can cause a fire.
Using a flash too close to a person’s eyes may temporarily affect the eyesight.
Take particular care when photographing infants and young children.
When a memory card is removed, the card could come out of the slot too quickly. Use your finger to hold it and gently release the card.
Request regular internal testing and cleaning for your camera.
Build-up of dust in your camera can cause a fire or electric shock.
• Contact your FUJIFILM dealer to request internal cleaning every 2
years.
• Please note this is not a free of charge service.
Do not use this camera in locations affected by oil fumes, steam, humidity or
dust.
This can cause a fire or electric shock.
Do not leave this camera in places subject to extremely high temperatures.
Do not leave the camera in locations such as a sealed vehicle or in
direct sunlight. This can cause a fire.
Keep out of the reach of small children.
This product could cause injury in the hands of a child.
v
For Your Safety
Power Supply and Battery
* Confirm your battery type before reading the following descriptions.
The following explains proper use of
batteries and how to prolong their
life. Incorrect use of batteries can
cause shorter battery life, as well as
leakage, excessive heat, fire or explosion.
1 Camera uses the Rechargeable
Lithium-ion Battery
* When shipped, the battery is not
fully charged. Always charge the
battery before using it.
* When carrying the battery, install it
in a digital camera or keep it in the
soft case.
■ Battery Features
• The battery gradually loses its
charge even when not used. Use
a battery that has been charged
recently (in the last day or two) to
take pictures.
• To maximize the life of the battery,
turn the camera off as quickly as
possible when it is not being used.
• The number of available frames will
be lower in cold locations or at low
temperatures. Take along a spare
fully charged battery. You can also
increase the amount of power produced by putting the battery in
your pocket or another warm place
to heat it and then loading it into
the camera just before you take a
picture.
vi
■ Battery Life
At normal temperatures, the battery can be used at least 300 times.
If the time for which the battery
provides power shortens markedly,
this indicates that the battery has
■ Charging the Battery
• You can charge the battery using reached the end of its effective life
and should be replaced.
the battery charger (included).
- The battery can be charged ■ Notes on storage
at ambient temperatures be- • If a battery is stored for long periods
tween 0°C and +40°C (+32°F
while charged, the performance of
and +104°F). Refer to the Owner’s
the battery can be impaired. If the
Manual for the time of charging
battery will not be used for some
battery.
time, run the battery out before
- You should charge the battery
storing it.
at an ambient temperature be- • If you do not intend to use the
tween +10°C and +35°C (+50°F
camera for a long period of time,
and +95°F). If you charge the
remove the battery from the cambattery at a temperature outside
era.
this range, charging takes longer • Store the battery in a cool place.
because the performance of the
- The battery should be stored in
battery is impaired.
a dry location with an ambient
- You cannot charge the battery
temperature between +15°C and
at temperatures of 0°C (+32°F) or
+25°C (+59°F and +77°F).
below.
- Do not leave the battery in hot or
• The Rechargeable Lithium-ion Batextremely cold places.
tery does not need to be fully dis■ Handling the Battery
charged or exhausted flat before
Cautions for Your Safety:
being charged.
• Do not carry or store battery with
• The battery may feel warm after it
metal objects such as necklaces or
has been charged or immediately
hairpins.
after being used. This is perfectly • Do not heat the battery or throw it
normal.
into a fire.
• Do not recharge a fully charged • Do not attempt to take apart or
battery.
change the battery.
If you are using a heating pad, take
care not to place the battery directly against the pad. The camera
may not operate if you use a depleted battery in cold conditions.
• Dispose of used battery promptly.
• Do not drop the battery or otherwise subject it to strong impacts.
• Do not expose the battery to water.
• Always keep the battery terminals
clean.
• Do not store batteries in hot places. Also, if you use the battery for
a long period, the camera body
and the battery itself will become
warm. This is normal. Use the AC
power adapter if you are taking
pictures or viewing images for a
long period of time.
2 Camera uses AA-size alkaline or Ni-MH
(nickel-metal hydride) rechargeable
batteries
* For details on the batteries that
you can use, refer to the Owner’s
Manual of your camera.
■ Cautions for Using Battery
• Do not heat the batteries or throw
them into a fire.
• Do not carry or store batteries with
metal objects such as necklaces or
hairpins.
• Do not expose the batteries to water, and keep batteries from getting
wet or stored in moist locations.
• Do not attempt to take apart or
change the batteries, including
battery casings.
• Do not subject the batteries to
strong impacts.
• Do not recharge the battery with
• Do not use batteries that are leakchargers other those specified.
ing, deformed, discolored.
For Your Safety
• Do not store batteries in warm or
If any liquid at all leaks from
humid places.
the batteries, wipe the battery
• Keep the batteries out of reach of
compartment thoroughly and
babies and small children.
then load new batteries.
• Make sure that the battery polarity
If any battery fluid comes into
(C and D) is correct.
contact with your hands or
• Do not use new with used batterclothing, flush the area thories. Do not use charged and disoughly with water. Note that
charged batteries together.
battery fluid can cause loss
• Do not use different types or
of eyesight if it gets into your
brands of batteries at the same
eyes. If this occurs, do not rub
time.
your eyes. Flush the fluid out
• If you do not intend to use the
with clean water and contact
camera for a long period of time,
your physician for treatment.
remove the batteries from the
camera. Note if the camera is left ■ Using the AA-size Ni-MH batteries
with the batteries removed, the
correctly
time and date settings are cleared. • Ni-MH batteries left unused in
• The batteries feel warm right afstorage for long periods can beter being used. Before removing
come “deactivated”. Also, repeatthe batteries, turn the camera off
edly charging Ni-MH batteries
and wait for the batteries to cool
that are only partially discharged
down.
can cause them to suffer from the
• Since batteries do not work well in
“memory effect”. Ni-MH batteries
cold weather or locations, warm
that are “deactivated” or affected
the batteries by placing them inby “memory” suffer from the probside your garments before use.
lem of only providing power for a
Batteries do not work well when
short time after being charged. To
cold. They will work again when
prevent this problem, discharge
the temperature returns to normal.
and recharge them several times
• Soil (such as fingerprints) on the
using the camera’s “Discharging
battery terminals makes the batrechargeable batteries” function.
teries charge less reducing the
Deactivation and memory are spenumber of images. Carefully wipe
cific to Ni-MH batteries and are not
the battery terminals with a soft
in fact battery faults.
dry cloth before loading.
See Owner’s Manual for the procedure for “Discharging rechargeable
batteries”.
CAUTION
Do not use the “Discharging rechargeable batteries” function when
alkaline batteries being used.
• To charge Ni-MH batteries, use the
quick battery charger (sold separately). Refer to the instructions
supplied with the charger to make
sure that the charger is used correctly.
• Do not use the battery charger to
charge other batteries.
• Note that the batteries feel warm
after being charged.
• Due to the way the camera is constructed, a small amount of current
is used even when the camera is
turned off. Note in particular that
leaving Ni-MH batteries in the
camera for a long period will overdischarge the batteries and may
render them unusable even after
recharging.
• Ni-MH batteries will self-discharge
even when not used, and the time
for which they can be used may be
shortened as a result.
• Ni-MH batteries will deteriorate
rapidly if over-discharged (e.g.
by discharging the batteries in a
flashlight). Use the “Discharging rechargeable batteries” function provided in the camera to discharge
the batteries.
• Ni-MH batteries have a limited
service life. If a battery can only
be used for a short time even after
repeated discharge-charge cycles,
it may have reached the end of its
service life.
■ Disposing of Batteries
• When disposing of batteries, do
so in accordance with your local
waste disposal regulations.
3 Notes on both models ( 1 , 2 )
■ AC Power Adapter
Always use the AC Power Adapter
with the camera. The use of an AC
Power adapter other than FUJIFILM
AC Power Adapter can be damaged
to your digital camera.
For details on the AC power adapter,
refer to the Owner’s Manual of your
camera.
• Use the AC power adapter for indoor use only.
• Plug the connection cord plug securely into the DC input terminal.
• Turn off the FUJIFILM Digital camera before disconnecting the cord
from the DC input terminal. To disconnect, pull out the plug gently.
Do not pull on the cord.
• Do not use the AC power adapter
with any device other than your
camera.
• During use, the AC power adapter
will become hot to the touch. This
is normal.
vii
For Your Safety
• Do not take apart the AC power
adapter. Doing so could be dangerous.
• Do not use the AC power adapter
in a hot and humid place.
• Do not subject the AC power
adapter to strong shocks.
• The AC power adapter may emit a
humming. This is normal.
• If used near a radio, the AC power
adapter may cause static. If this
happens, move the camera away
from the radio.
Before Using the Camera
Do not aim the camera at extremely
bright light sources, such as the sun
in a cloudless sky. Failure to observe
this precaution could damage the
camera image sensor.
■ Test Shots Prior to Photography
For important photographs (such as
weddings and overseas trips), always
take a test shot and view the image to make sure that the camera is
working normally.
• FUJIFILM Corporation cannot accept liability for any incidental
losses (such as the costs of photography or the loss of income from
photography) incurred as a result
of faults with this product.
■ Notes on Copyright
Images recorded using your digital
camera system cannot be used in
ways that infringe copyright laws
without the consent of the owner,
viii
Although the LCD panel is produced ■ Explanation of Color Television
System
with highly sophisticated technologies, there may be black spots or NTSC: National Television System
Committee, color television
permanently lit spots. This is not a
telecasting
specifications
malfunction, and does not affect readopted mainly in the U.S.A.,
corded images.
Canada and Japan.
■ Trademark Information
xD-Picture Card and E are trade- PAL: Phase Alternation by Line, a
color television system admarks of FUJIFILM Corporation. The
opted mainly by European
typefaces included herein are solely
countries and China.
developed by DynaComware Tai■ Handling Your Digital Camera
wan Inc. Macintosh, QuickTime, and
To ensure that images are recorded Mac OS are trademarks of Apple Inc. ■ Exif Print (Exif ver. 2.3)
correctly, do not subject the camera in the U.S.A. and other countries. Exif Print Format is a newly revised
to impact or shock while an image is Windows 7, Windows Vista, and the digital camera file format that conbeing recorded.
Windows logo are trademarks of tains a variety of shooting informathe Microsoft group of companies. tion for optimal printing.
■ Liquid Crystal
Adobe and Adobe Reader are either
If the LCD monitor is damaged, take
IMPORTANT NOTICE: Read Before
trademarks or registered trademarks
particular care with the liquid crystal
Using the Software
of Adobe Systems Incorporated in
in the monitor. If any of the followthe U.S.A. and/or other countries. Direct or indirect export, in whole or
ing situations arise, take the urgent
The SDHC and SDXC logos are trade- in part, of licensed software without
action indicated.
marks of SD-3C, LLC. The HDMI logo the permission of the applicable
• If liquid crystal comes in contact
is a trademark. YouTube is a trade- governing bodies is prohibited.
with your skin:
mark of Google Inc. All other trade
Wipe the area with a cloth and
names mentioned in this manual are
then wash thoroughly with soap
the trademarks or registered tradeand running water.
marks of their respective owners.
• If liquid crystal gets into your eye:
Flush the affected eye with clean ■ Notes on Electrical Interference
water for at least 15 minutes and If the camera is to be used in hosthen seek medical assistance.
pitals or aircrafts, please note that
• If liquid crystal is swallowed:
this camera may cause interference
Flush your mouth thoroughly with to other equipment in the hospital
water. Drink large quantities of wa- or aircraft. For details, please check
ter and induce vomiting. Then seek with the applicable regulations.
medical assistance.
unless intended only for personal
use. Note that some restrictions apply to the photographing of stage
performances, entertainments and
exhibits, even when intended purely
for personal use. Users are also asked
to note that the transfer of Memory
Card containing images or data protected under copyright laws is only
permissible within the restrictions
imposed by those copyright laws.
About This Manual
Before using the camera, read this manual and the warnings on pages ii–viii. For information on specific topics, consult the sources below.
✔ Table of Contents ............................................... P x
The “Table of Contents” gives an overview of the
entire manual. The principal camera operations
are listed here.
✔ Troubleshooting ............................................ P 102
Having a specific problem with the camera? Find
the answer here.
✔ Warning Messages and Displays ..................... P 109
Find out what’s behind that flashing icon or error
message in the display.
Temperature Warning
The camera will turn off automatically before its temperature or the temperature of the battery rise above safe
limits. Pictures taken when a temperature warning is displayed may exhibit higher levels of “noise” (mottling).
Turn the camera off and wait for it to cool before turning it on again (P 105, 110).
ix
Table of Contents
For Your Safety ................................................................................. ii
IMPORTANT SAFETY INSTRUCTIONS ...................................... ii
Safety Notes .................................................................................... iv
About This Manual ......................................................................... ix
Before You Begi
Begin
n
Introduction....................................................................................... 1
Symbols and Conventions .......................................................... 1
Supplied Accessories .................................................................... 1
Parts of the Camera ....................................................................... 2
Camera Displays .......................................................................... 5
First Steps
Steps
The Strap and Lens Cap ................................................................ 7
Inserting the Batteries .................................................................. 8
Inserting a Memory Card ...........................................................10
Turning the Camera on and Off ..............................................13
Basic Setup .......................................................................................14
Basic Photography and Playbac
Playback
k
Taking Pictures in R (E AUTO) Mode......................15
Viewing Pictures ............................................................................20
More on Photography
Photography
Shooting Mode ...............................................................................21
O (E AUTO/E Priority) ..................................22
B AUTO ..........................................................................................23
Adv. ADVANCED...........................................................................23
SP1/SP2 SCENE POSITION ........................................................25
N MOTION PANORAMA 360 ............................................27
P: PROGRAM AE ............................................................................28
S: SHUTTER PRIORITY AE ...........................................................29
x
A: APERTURE PRIORITY AE ........................................................29
M: MANUAL ....................................................................................30
C: CUSTOM MODE ........................................................................30
Focus Lock ........................................................................................31
The AE/AF LOCK Button ....................................................................32
Locking Exposure......................................................................32
Locking Focus .............................................................................32
F Macro and Super Macro Modes (Close-ups) ...............33
N Using the Flash (Super-Intelligent Flash) ......................34
J Using the Self-Timer...............................................................36
d Exposure Compensation.....................................................37
Sensitivity .........................................................................................38
Metering ............................................................................................39
Autofocus Mode.............................................................................40
Focus Mode ......................................................................................41
White Balance .................................................................................43
I Continuous Shooting (Burst Mode)................................44
b Intelligent Face Detection ..................................................48
n Face Recognition ....................................................................49
Adding New Faces .......................................................................49
Viewing, Editing, and Deleting Existing Data ...................50
Adding Faces Automatically ....................................................50
More on Playback
Playback
Playback Options...........................................................................52
Continuous Shooting .................................................................52
I Favorites: Rating Pictures ....................................................52
Playback Zoom..............................................................................53
Multi-Frame Playback.................................................................54
A Deleting Pictures ....................................................................55
Viewing Photo Information ......................................................56
Table of Contents
Image Search ...................................................................................57
X PhotoBook Assist ...................................................................58
Creating a PhotoBook ................................................................58
Viewing PhotoBooks ..................................................................59
Editing and Deleting PhotoBooks .........................................59
Viewing Panoramas......................................................................60
Moviess
Movie
Recording Movies..........................................................................61
Movie Frame Size .........................................................................62
a Viewing Movies .......................................................................63
Connectionss
Connection
Viewing Pictures on TV ...............................................................64
Printing Pictures via USB ...........................................................66
Connecting the Camera ............................................................66
Printing Selected Pictures ........................................................66
Printing the DPOF Print Order ................................................67
Creating a DPOF Print Order ....................................................69
Viewing Pictures on a Computer............................................72
Installing the Software...............................................................72
Connecting the Camera ............................................................76
Menuss
Menu
Using the Menus: Shooting Mode .........................................78
Using the Shooting Menu.........................................................78
Shooting Menu Options ............................................................78
A E MODE ..........................................................................78
A Adv. MODE ..............................................................................78
A SCENE POSITION ....................................................................78
N ISO ...............................................................................................78
O IMAGE SIZE...............................................................................78
T IMAGE QUALITY .....................................................................79
U DYNAMIC RANGE ..................................................................80
P FILM SIMULATION .................................................................80
d WB SHIFT ..................................................................................81
f COLOR........................................................................................81
e TONE...........................................................................................81
H SHARPNESS..............................................................................81
h NOISE REDUCTION................................................................81
Z ADVANCED ANTI BLUR ........................................................81
b FACE DETECTION...................................................................81
n FACE RECOGNITION..............................................................81
F MOVIE AF MODE ....................................................................82
W MOVIE MODE ..........................................................................82
J AE BKT EV STEPS ....................................................................82
I FLASH.........................................................................................82
g EXTERNAL FLASH ..................................................................83
K CUSTOM SET............................................................................83
2 ELECTRONIC LEVEL ..............................................................83
Using the Menus: Playback Mode ..........................................84
Using the Playback Menu .........................................................84
Playback Menu Options.............................................................84
X PHOTOBOOK ASSIST............................................................84
x ERASE .........................................................................................84
j MARK FOR UPLOAD TO .......................................................84
I SLIDE SHOW ............................................................................85
B RED EYE REMOVAL ................................................................86
D PROTECT ...................................................................................86
G CROP ..........................................................................................87
O RESIZE ........................................................................................87
C IMAGE ROTATE........................................................................88
xi
Table of Contents
E COPY...........................................................................................88
F VOICE MEMO ...........................................................................89
n ERASE FACE RECOG. .............................................................89
K PRINT ORDER (DPOF) ...........................................................89
J DISP. ASPECT ...........................................................................90
The Setup Menu .............................................................................91
Using the Setup Menu ...............................................................91
Setup Menu Options...................................................................92
F DATE/TIME ...............................................................................92
N TIME DIFFERENCE ..................................................................92
L a .................................................................................92
o SILENT MODE ..........................................................................92
R RESET .........................................................................................93
K FORMAT ....................................................................................93
A IMAGE DISP. .............................................................................93
B FRAME NO. ...............................................................................94
G OPERATION VOL. ...................................................................94
H SHUTTER VOLUME ................................................................94
e SHUTTER SOUND...................................................................94
I PLAYBACK VOLUME ..............................................................95
J LCD BRIGHTNESS ...................................................................95
E EVF/LCD MODE ......................................................................95
M AUTO POWER OFF .................................................................95
1 QUICK START MODE.............................................................95
L DUAL IS MODE ........................................................................95
B RED EYE REMOVAL ................................................................96
C AF ILLUMINATOR ...................................................................96
k AE/AF-LOCK MODE ...............................................................96
v AE/AF-LOCK BUTTON ..........................................................96
j RAW ............................................................................................96
j FOCUS CHECK .........................................................................97
xii
t SAVE ORG IMAGE ...................................................................97
m AUTOROTATE PB ....................................................................97
O BACKGROUND COLOR .........................................................97
c GUIDANCE DISPLAY..............................................................97
Q VIDEO SYSTEM........................................................................97
S CUSTOM RESET ......................................................................98
T BATTERY TYPE.........................................................................98
P DISCHARGE (Ni-MH Batteries Only) ...............................98
Technical Note
Notess
Optional Accessories ...................................................................99
Accessories from FUJIFILM .................................................... 100
Caring for the Camera ...............................................................101
Troubleshooting
Troubleshootin
g
Troubleshooting ......................................................................... 102
Warning Messages and Displays ......................................... 109
Appendix
Appendi
x
Internal Memory/Memory Card Capacity ........................113
Specifications ................................................................................114
Introduction
Symbols and Conventions
Menus and other text in the camera monitor are shown in bold. In the illustrations in this manual, the
monitor display may be simplified for explanatory purposes.
Before You Begin
The following symbols are used in this manual:
3 Caution: This information should be read before use to ensure correct operation.
1 Note: Points to note when using the camera.
2 Tip: Additional information that may be helpful when using the camera.
Supplied Accessories
The following items are included with the camera:
AA alkaline (LR6) batteries
(×4)
Lens cap
USB cable
A/V cable
• Strap
• Basic Manual
Lens hood
CD-ROM
1
Introduction
Parts of the Camera
For more information, refer to the page listed to the right of each item.
Command dial ...........................28, 38, 44 8 d (exposure compensation) button .........37
Mode dial ......................................................21 9 R (continuous shooting) button .............. 44
Hot shoe .............................................83, 100 10 Memory card slot cover ....................... 11
AF-assist illuminator ...............................96 11 Strap eyelet .................................................... 7
Self-timer lamp ..........................................36 12 Memory card slot ..................................... 11
5 Lens
13 Flash..................................................................34
6 ON/OFF switch ..............................................13 14 Microphone ......................................... 61, 89
7 Shutter button ...........................................17 15 N (flash pop-up) button ..............................34
1
2
3
4
2
16
17
18
19
20
21
22
Speaker ...................................................63, 89
Terminal cover
Focus ring .....................................................41
Zoom ring .....................................................16
Connector for HDMI cable ................ 64
USB cable connector .....................66, 76
A/V cable connector ............................ 64
Introduction
Monitor ............................................................. 5
Tripod mount
Battery-chamber cover .......................... 8
Diopter adjustment control ................ 4
Indicator lamp ............................................19
ISO (sensitivity) button ................................38
k (playback zoom in) button .....................53
29 AE (autoexposure) button ............................39
n (playback zoom out) button ..................53
30 AF (autofocus) button...................................40
g (Intelligent Face Detection) button ...53, 70
31 AF C-S-M (focus mode) button ...................41
info button....................................................56
32 WB (white balance) button ..........................43
H (image search) button...........................57
33 Electronic viewfinder .............................. 4
34 Eye sensor ....................................................... 4
35 EVF/LCD (display selection) button.............. 4
36 ● (movie record) button .............................61
37 AE/AF LOCK (autoexposure/autofocus lock)
button .............................................................32
38 Selector button (see below)
39 a (playback) button ..................................52
40 DISP (display)/BACK button ..............18, 52
Before You Begin
23
24
25
26
27
28
The Selector Button
Move cursor up
RAW button (P 18)/
b (delete) button (P 20)
MENU/OK button (P 14)
Move cursor left
F (macro) button (P 33)
Move cursor right
N (flash) button (P 34)
Move cursor down
h (self-timer) button (P 36)
3
Introduction
The Electronic Viewfinder (EVF)
The electronic viewfinder provides the same information as the monitor, and
can be used when bright lighting conditions make the display in the monitor
difficult to see. Press EVF/LCD button to select from the auto switch, monitor, or
electric view finder mode. When the auto switch mode is set, the electric view
finder turns on automatically when you put your eye to the view finder, and the
monitor turns on when you take your eye away (note that the eye sensor may not
respond if you are wearing glasses or your head is an angle to the camera).
EVF
LCD
Eye sensor
The camera is equipped with diopter adjustment to accommodate individual
differences in vision. Slide the diopter adjustment control up and down until the
viewfinder display is in sharp focus.
4
Introduction
■ Shooting
1 Shooting mode .........................................21
2 Intelligent Face Detection
indicator .........................................................48
800
N
3 Metering ........................................................39
4 Continuous shooting mode ............ 44
5 Silent mode indicator....................18, 92
6 Focus warning .................................17, 109
12/31/2050
10 : 00 AM
7 Internal memory indicator *
250
F4.5
8 Movie mode ................................................61
9 Temperature warning .............. 105, 110
* a: indicates that no memory card
10 Number of available frames............113
is inserted and that pictures will
11 Sensitivity ......................................................38
be stored in the camera’s internal
12 Image size/quality ...........................78, 79
memory (P 10).
13 Dynamic range ..........................................80
P
9
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Film simulation ..........................................80
White balance ............................................43
Battery level ................................................... 6
Dual IS mode ..............................................95
Exposure indicator ..................................37
Exposure compensation .....................37
Aperture
Shutter speed
Date and time.............................................14
Blur warning .....................................34, 109
Focus frame .................................................31
Self-timer indicator .................................36
Macro (close-up) mode........................33
Flash mode...................................................34
8
9
10
11
12
13
14
15
E mode ..............................................22
Portrait enhancer .....................................25
Mark for upload to.................................. 84
Photobook assist ......................................58
Voice memo indicator...........................89
DPOF print indicator ..............................67
Protected image .......................................86
Favorites .........................................................52
Before You Begin
Camera Displays
The following indicators may appear during shooting and playback. The indicators displayed vary with
camera settings.
■ Playback
100-0001
400
N
YouTube
12/31/2050
10 : 00 AM
1 / 250
F4.5
1 Playback mode indicator ............20, 52
2 Intelligent Face Detection
indicator .................................................48, 86
3 Red-eye removal indicator ................86
4 Pro focus mode, pro low-light
mode........................................................23, 24
5 Gift image .....................................................52
6 Frame number ...........................................94
7 Dynamic range ..........................................80
5
Introduction
Battery Level
Battery level is shown as follows:
Indicator
Description
NO ICON
Batteries are partially discharged.
Batteries are low. Replace as soon as
B (red)
possible.
A (blinks red) Batteries are exhausted. Turn camera
off and replace batteries.
1 Note
A battery warning may not be displayed before the
camera turns off, particularly if batteries are reused
after having once been exhausted. Power consumption varies greatly from mode to mode; the low battery warning (B) may not be displayed or may be
displayed only briefly before the camera turns off in
some modes or when switching from shooting to
playback mode.
6
Hiding and Viewing Indicators
To choose the shooting information and guides displayed, press the DISP/BACK button.
The Strap and Lens Cap
Attaching the Strap
Attach the strap to the two strap eyelets as shown
below.
The Lens Cap
Attach the lens cap as shown.
First Steps
To avoid losing the lens cap, pass the supplied
string through the eyelet (q) and secure the lens
cap to the strap (w).
3 Caution
To avoid dropping the camera, be sure the strap is correctly secured.
7
Inserting the Batteries
The camera takes four AA alkaline, lithium, or rechargeable Ni-MH batteries. A set of four alkaline batteries is supplied with the camera. Insert the batteries in the camera as described below.
the battery-chamber cover.
1 Open
Slide the battery-chamber latch in the direction shown and open
the battery-chamber
cover.
1 Note
Be sure the camera is off before opening the battery-chamber cover.
3 Cautions
• Do not open the battery-chamber cover when
the camera is on. Failure to observe this precaution could result in damage to image files or
memory cards.
• Do not use excessive force when handling the
battery-chamber cover.
8
Insert the batteries.
2 Insert
the batteries
in
the orientation shown
by the “+“ and “–“ marks
inside the battery chamber.
3 Cautions
• Insert the batteries in the correct orientation.
• Never use batteries with peelBattery casing
ing or damaged casing or mix
old and new batteries, batteries with different charge levels,
or batteries of different types.
Failure to observe these
precautions could result
in the batteries leaking or
overheating.
• Never use manganese or Ni-Cd batteries.
• The capacity of alkaline batteries varies with the
manufacturer and drops at temperatures below
10 °C/50 °F; Ni-MH batteries are recommended.
• Fingerprints and other soil on the battery terminals can shorten battery life.
Inserting the Batteries
the battery-chamber cover.
3 Close
Close the battery-cham-
3 Caution
Do not use force. If the
battery-chamber cover does not close, check
that the batteries are in the correct orientation
and try again.
First Steps
ber cover and slide it in
until the latch clicks into
place.
Choosing the Battery Type
SET-UP
After replacing the batteries
with batteries of a different
LITHIUM
ALKALINE
type, select the battery type usBATTERY TYPE
NI-MH
ing the T BATTERY TYPE option in the setup menu (P 91)
to ensure that the battery level
is displayed correctly and the camera does not turn
off unexpectedly.
2 Tip: Using an AC Power Adapter
The camera can be powered by an optional AC
power adapter and DC coupler (sold separately).
9
Inserting a Memory Card
Although the camera can store pictures in internal memory, optional SD, SDHC and SDXC memory
cards (sold separately) can be used to store additional pictures.
■ Compatible Memory Cards
FUJIFILM and SanDisk SD, SDHC and SDXC memory cards have been approved for use in the camera. A
complete list of approved memory cards is available at http://www.fujifilm.com/support/digital_cameras/
compatibility/. Operation is not guaranteed with other cards. The camera can not be used with xDPicture Cards or MultiMediaCard (MMC) devices.
3 Caution
Memory cards can be locked, making it impossible to format the card or to record or delete
images. Before inserting a memory card, slide the write-protect switch to the unlocked position.
Write-protect
switch
Memory Cards
Pictures can be stored in the camera’s internal memory or on optional SD, SDHC, and SDXC memory cards,
referred to in this manual as “memory cards.”
10
Inserting a Memory Card
■ Inserting a Memory Card
Open the memory card slot cover.
1
the memory card.
2 Insert
Holding the memory card in the orientation
shown below, slide it in until it clicks into
place at the back of the slot.
Click
First Steps
1 Note
Be sure the camera is off
before opening the memory card slot cover.
Be sure card is in the correct
orientation; do not insert at
an angle or use force. If the
memory card is not correctly
inserted or no memory card
is inserted, a will appear in
the LCD monitor and internal memory will be used for
recording and playback.
3 Close the memory card slot cover.
Removing Memory Cards
After confirming that the camera
is off, press the card in and then
release it slowly. The card can
now be removed by hand.
3 Cautions
• The memory card may spring out if you remove
your finger immediately after pushing the card in.
• Memory cards may be warm to the touch after being removed from the camera. This is normal and
does not indicate a malfunction.
11
Inserting a Memory Card
3 Cautions
• Do not turn the camera off or remove the memory card while the memory card is being formatted or data are being recorded to or
deleted from the card. Failure to observe this precaution could damage the card.
• Format SD/SDHC/SDXC memory cards before first use, and be sure to reformat all memory cards after using
them in a computer or other device. For more information on formatting memory cards, see “K FORMAT”
(P 93).
• Memory cards are small and can be swallowed; keep out of reach of children. If a child swallows a memory card,
seek medical assistance immediately.
• miniSD or microSD adapters that are larger or smaller than the standard dimensions of an SD/SDHC/SDXC card
may not eject normally; if the card does not eject, take the camera to an authorized service representative. Do
not forcibly remove the card.
• Do not affix labels to memory cards. Peeling labels can cause camera malfunction.
• Movie recording may be interrupted with some types of SD/SDHC/SDXC memory card. Use a G card or
better when shooting HD or high-speed movies.
• The data in internal memory may be erased or corrupted when the camera is repaired. Please note that the
repairer will be able to view pictures in internal memory.
• Formatting a memory card or internal memory in the camera creates a folder in which pictures are stored. Do
not rename or delete this folder or use a computer or other device to edit, delete, or rename image files. Always
use the camera to delete pictures from memory cards and internal memory; before editing or renaming files,
copy them to a computer and edit or rename the copies, not the originals.
12
Turning the Camera on and Off
Rotate the ON/OFF switch to ON to turn the camera
on.
b Tip: Switching to Playback Mode
Press the a button to start playback. Press a button
again or press the shutter button halfway to return to
shooting mode.
b Tip: Auto Power Off
The camera will turn off automatically if no operations
are performed for the length of time selected in the
M AUTO POWER OFF menu (P 95). To reactivate
the camera after it has turned off automatically, turn
the ON/OFF switch to OFF and then back to ON.
First Steps
Select OFF to turn the camera off.
c Cautions
• Pictures can be affected by fingerprints and other
marks on the lens. Keep the lens clean.
• The ON/OFF switch does not completely disconnect
the camera from its power supply.
13
Basic Setup
A language-selection dialog is displayed the first time the camera is turned on. Set up the camera as
described below (for information on resetting the clock or changing languages, see page 93).
1 Highlight a language and press MENU/OK.
START MENU
ENGLISH
FRANCAIS
DEUTSCH
ESPAÑOL
PORTUGUÊS
SET
1 Note
Press DISP/BACK to skip the current step. Any steps you skip will be displayed
the next time the camera is turned on.
NO
The date and time will be displayed. Press the selector left or right to
2 highlight
the year, month, day, hour, or minute and press up or down
DATE / TIME NOT SET
2013
2012
YY. MM. DD
SET
2011
2010
2009
1. 1
NO
12 : 00
AM
to change. To change the order in which the year, month, and day
are displayed, highlight the date format and press the selector up or
down. Press MENU/OK when settings are complete.
battery type message will be displayed; if the type differs from the
3 Atype
inserted in the camera, use the setup menu T BATTERY TYPE
option (P 9) to specify the correct type.
2 Tip: The Camera Clock
If the batteries are removed for an extended period, the camera clock and battery type will be reset and the
language-selection dialog will be displayed when the camera is turned on.
14
Taking Pictures in R (E AUTO) Mode
This section describes how to take pictures in R (E AUTO) mode.
O mode.
1 Select
Turn the camera on and rotate the mode dial to O. The R display will appear in the LCD
monitor.
EXR Icons (P 23)
The camera analyses the scene and
selects the preferred E mode.
RESOLUTION PRIORITY
HIGH ISO & LOW NOISE
D-RANGE PRIORITY
S
T
U
Scene Icons
The camera automatically selects the appropriate scene.
Scene
AUTO
Main subject
Non-portrait (landscape)
a
Normal lighting ab
Portrait
Back lighting
ag
LANDSCAPE
c
cb
cg
NIGHT
MACRO
BEACH
SUNSET
SNOW
SKY
GREENERY
d*
fb*
—
e
—
—
u
ub
ug
v
vb
vg
w
wb
wg
x
xb
xg
y
yb
yg
SKY &
GREENERY
z
zb
zg
Basic Photography and Playback
The o Icon
In R mode, the camera continuously adjusts focus and searches for faces, increasing the drain on the
battery. o is displayed in the LCD monitor.
* If n is displayed, the camera will take a series of shots (Advanced anti blur; P 22).
3 Caution
The mode selected may vary with shooting conditions. If the mode and subject do not match, select
B mode (P 23) or choose SP1/SP2 (P 25) and select a scene manually.
15
Taking Pictures in R (E AUTO) Mode
the picture.
2 Frame
Use the zoom ring
to
frame the picture in the
display.
Zoom ring
Rotate left to zoom out
Zoom indicator
Rotate right to zoom in
2 Tip: Focus Lock
Use focus lock (P 31) to focus on subjects that are not
in the focus frame.
16
Holding the Camera
Hold the camera steady with
both hands and brace your
elbows against your sides.
Shaking or unsteady hands
can blur your shots.
To prevent pictures that are
out of focus or too dark (underexposed), keep your fingers and other objects away
from the lens and flash.
Taking Pictures in R (E AUTO) Mode
Focus.
3 Press
the shutter button halfway
to focus.
2 Tip: The Shutter Button
The shutter button has two positions. Pressing the
shutter button halfway (q) sets focus and exposure;
to shoot, press the shutter button the rest of the way
down (w).
If the camera is able to focus, it will beep twice
and the indicator lamp will glow green.
Shoot.
4 Smoothly
press the shutter button the rest of the way down to
take the picture.
q
Press halfway
Click
w
Press the rest of
the way down
1 Note
If the subject is poorly lit, the AF-assist illuminator may
light to assist focus (P 96). For information on using
the flash when lighting is poor, see page 34.
Basic Photography and Playback
If the camera is unable to focus, the focus frame
will turn red, s will be displayed, and the
indicator lamp will blink green. Change the
composition or use focus lock (P 31).
Double
beep
17
Taking Pictures in R (E AUTO) Mode
Silent Mode
In situations in which camera sounds or lights may
be unwelcome, hold the DISP/BACK button down until
o is displayed (note that silent mode is not available
during movie or voice memo playback).
The camera speaker, flash, and AF-assist illuminator/
self-timer lamp turn off and flash and volume settings
can not be adjusted (note that the flash will still fire
when C is selected in scene mode). To restore normal operation, press the DISP/BACK button until the o
icon is no longer displayed.
18
RAW button
Press the RAW button to temporarily change the recording format. After shooting a picture, the recording format will be back to the option selected for
j RAW in the setup menu (P 96).
RAW button pressed
j options
JPEG
RAW+JPEG
JPEG
RAW
OFF
RAW+JPEG
Taking Pictures in R (E AUTO) Mode
The Indicator Lamp
Indicator lamp
Basic Photography and Playback
The indicator lamp shows camera status as follows:
Indicator lamp
Camera status
Glows green Focus locked.
Blur, focus, or exposure warning. PicBlinks green
ture can be taken.
Blinks green Recording pictures. Additional picand orange tures can be taken.
Glows
Recording pictures. No additional picorange
tures can be taken at this time.
Flash charging; flash will not fire when
Blinks orange
picture is taken.
Lens or memory error (memory card
Blinks red full or not formatted, format error, or
other memory error).
2 Tip: Warnings
Detailed warnings appear in the display. See pages
109–112 for more information.
19
Viewing Pictures
Pictures can be viewed in the monitor. When taking important photographs, take a test shot and
check the results.
1 Press the a button.
Deleting Pictures
To delete the picture currently displayed
in the monitor, press the selector up (b).
The following dialog will be displayed.
ERASE OK?
The most recent picture will be displayed in
the monitor.
100-0001
2
View additional pictures.
Press the selector right to view
pictures in the order recorded, left
to view pictures in reverse order.
Press the shutter button to exit to shooting
mode.
20
OK
CANCEL
SET
To delete the picture, highlight OK and
press MENU/OK. To exit without deleting
the picture, highlight CANCEL and press
MENU/OK.
2 Tip: The Playback Menu
Pictures can also be deleted from the playback menu
(P 55).
Shooting Mode
Choose a shooting mode according to the scene or type of subject. To
choose a shooting mode, rotate the mode dial to the desired setting. The
following modes are available:
P, S, A, M: Select for full control over camera settings, including
aperture (M and A) and/or shutter speed (M and S) (P 28).
C (CUSTOM): Recall stored settings for
modes P, S, A, M and all O modes
except R (P 30).
B (AUTO): A simple “point-and-shoot”
mode recommended for first-time users
of digital cameras (P 23).
N (MOTION PANORAMA 360): Select for
taking a panorama (P 27).
Adv. (ADVANCED): Sophisticated techniques made easy (P 23).
More on Photography
O: Improve clarity, reduce noise, increase dynamic range, or let the camera
automatically adjust settings to suit the
scene (P 22).
SP1, SP2 (SCENE POSITION): Choose a scene suited to the subject
or shooting conditions and let the camera do the rest (P 25).
21
Shooting Mode
O ((E
E AUTO/
AUTO/E
E Priority)
Optimize settings for your current subject or improve clarity, reduce noise, or
enhance dynamic range. Rotate the
mode dial to O and choose one
of the following E modes in the
shooting menu.
■ R ((E
E AUTO)
The camera automatically selects the scene and
E mode according to shooting conditions
(P 15).
1 Note
If S is selected for O IMAGE SIZE in R mode, the
camera will automatically select the optimal image
size.
22
Advanced Anti Blur
When n is displayed, the camera will take a series of
exposures and combine them to form a single image,
reducing “noise” (mottling) and blur.
1 Note
n is available when ON is selected in the shooting
menu (P 81) and the flash (P 34) is off or set to
auto.
3 Cautions
• Some time may be required to combine the exposures into a single image. A single combined image
may not be created if the subject or camera moves
during shooting. Keep the camera steady during
shooting and do not move the camera until shooting is complete.
• Frame coverage is reduced.
Shooting Mode
■ i PRO FOCUS
The camera takes up to three
shots each time the shutter
button is pressed, softening
the background to emphasize
the main subject. The amount
of softening can be adjusted before shooting by
rotating the command dial. Use for portraits or
photos of flowers similar to those produced by
SLR cameras.
B AUTO
1 Note
Softening can not be applied to background objects
that are too close to the main subject. If a message
stating that the camera can not create the effect is
displayed when the camera focuses, try backing away
from your subject and zooming in. The camera may
also be unable to soften the background if the subject is moving; if prompted, check the results and try
again.
Choose for crisp, clear snapshots. This mode is
recommended in most situations.
Adv. ADVANCED
This mode combines “point-and-shoot”
simplicity with sophisticated photographic techniques. The A Adv. MODE option in the shooting menu can be used
to choose from the following advanced
modes:
More on Photography
■ E Priority
Choose from the following options:
• S (RESOLUTION PRIORITY): Choose for crisp, clear
shots.
• T (HIGH ISO & LOW NOISE): Reduce noise in pictures taken at high sensitivities.
• U (D-RANGE PRIORITY): Increase the amount of
detail visible in highlights.
U DYNAMIC RANGE (P 80) can be set to
M (1600%) and D (800%).
23
Shooting Mode
■ j PRO LOW-LIGHT
Each time the shutter button
is pressed, the camera makes
four exposures and combines
them into a single photograph.
Use to reduce noise and blur
when photographing poorly lit subjects or static
subjects at high zoom ratios.
1 Note
A single combined photograph may not be created
with some scenes or if the subject or camera moves
during shooting. Do not move the camera until shooting is complete.
24
PRO FOCUS/PRO LOW-LIGHT
To save unprocessed copies of pictures taken in these
modes, select ON for the t SAVE ORG IMAGE option in the setup menu (P 97).
3 Cautions
• Keep the camera steady during shooting.
• Frame coverage is reduced.
Shooting Mode
SP1/SP2 SCENE POSITION
The camera offers a choice of “scenes,” each adapted to particular shooting conditions or
a specific type of subject. Use the A SCENE POSITION option in the shooting menu to
choose the scene assigned to the SP1/SP2 position on the mode dial.
Scene
Description
The camera takes two shots: one without the flash and one with.
Capture natural lighting under low-light conditions.
Choose for portraits.
Choose for a smooth skin effect when shooting portraits.
Choose when photographing dogs.
Choose when photographing cats.
Choose for daylight shots of buildings and landscapes.
Choose when photographing moving subjects.
Choose this mode for poorly lit twilight or night scenes.
Choose this mode for slow shutter speeds when shooting at night.
Slow shutter speeds are used to capture the expanding burst of light from a firework.
Choose this mode to record the vivid colors in sunrises and sunsets.
Choose for crisp, clear shots that capture the brightness of scenes dominated by shining white snow.
Choose for crisp, clear shots that capture the brightness of sunlit beaches.
Capture indoor background lighting under low-light conditions.
Choose for vivid close-ups of flowers.
Take clear pictures of text or drawings in print.
More on Photography
C NATURAL & N
D NATURAL LIGHT
L PORTRAIT
Z PORTRAIT ENHANCER
T DOG
m CAT
M LANDSCAPE
N SPORT
O NIGHT
H NIGHT (TRIPOD)
U FIREWORKS
Q SUNSET
R SNOW
V BEACH
U PARTY
V FLOWER
W TEXT
25
Shooting Mode
T DOG/m CAT
The camera focuses on the faces of dogs or cats that are facing the camera, and the self-timer menu offers a
n AUTO RELEASE option that releases the shutter automatically when a pet is detected (P 36). During playback, image search (P 57) can be used to search for pictures taken in either mode.
1 Note
Although camera can detect many different breeds of dogs and cats, results may vary with the breed and
shooting conditions. The camera may fail to detect pets with dark-colored faces or long hair covering their
entire face. If a dog or cat is not detected, the camera focuses on the subject at the center of the frame.
26
Shooting Mode
N MOTION PANORAMA 360
Follow an on-screen guide
to take photos that will
automatically be joined to
form a panorama.
3
4
5
down. Press the selector left or right to highlight an angle and press MENU/OK.
Press the selector right to view a choice of pan
directions. Press the selector left or right to
highlight a pan direction and press MENU/OK.
Press the shutter button all the way down to
start recording. There is no need to keep the
shutter button pressed during recording.
Pan the camera in the di120
rection shown by the arrow.
Shooting ends automatically when the progress bar
is full and the panorama is
Progress bar
complete.
3 Cautions
• Panoramas are created from multiple frames. The
camera may in some cases record a greater or lesser
angle than selected or be unable to stitch the frames
together perfectly. The last part of the panorama
may not be recorded if shooting ends before the
panorama is complete.
• Shooting may be interrupted if the camera is panned
too quickly or too slowly. Panning the camera in a
direction other than that shown cancels shooting.
• The desired results may not be achieved with moving subjects, subjects close to the camera, unvarying
subjects such as the sky or a field of grass, subjects
that are in constant motion, such as waves and waterfalls, or subjects that undergo marked changes in
brightness. Panoramas may be blurred if the subject
is poorly lit.
More on Photography
the zoom ring until the zoom indicator
1 Rotate
turns white.
select the angle through which you will pan
2 To
the camera while shooting, press the selector
1 Note
Shooting ends if the shutter button is pressed all the
way down during shooting. No panorama will be recorded if the shutter button is pressed before the camera has been panned through 120 °.
27
Shooting Mode
For Best Results
For best results, move the camera in a small circle at
a steady speed, keeping the camera horizontal and
being careful only to pan in the direction shown by
the guides. If the desired results are not achieved, try
panning at a different speed.
P: PROGRAM AE
In this mode, the camera sets exposure
automatically. If desired, you can choose
different combinations of shutter speed
and aperture that will produce the same
exposure (program shift).
3 Caution
If the subject is outside the metering range of the camera, the shutter speed and aperture displays will show
“---”. Press the shutter button halfway to measure exposure again.
28
Program Shift
Rotate the command dial to choose the desired combination of shutter speed and aperture. The default
values can be restored by raising the flash, rotating
the mode dial to another setting, turning the camera off, or selecting playback mode. The flash must
be off for Program shift to be available. Furthermore,
an option other than AUTO must be selected for
U DYNAMIC RANGE and N ISO.
Shutter speed
250
F4.5
Aperture
Shooting Mode
S: SHUTTER PRIORITY AE
A: APERTURE PRIORITY AE
You choose the shutter speed using
the command dial, while the camera
adjusts aperture for optimal exposure.
You choose the aperture using the command dial, while the camera adjusts
shutter speed for optimal exposure.
Shutter speed
1000
F3.5
3 Caution
If the correct exposure can not be achieved at the selected aperture, shutter speed will be displayed in red.
Adjust aperture until the correct exposure is achieved.
If the subject is outside the metering range of the camera, the shutter speed display will show “---”. Press the
shutter button halfway to measure exposure again.
More on Photography
3 Cautions
• If the correct exposure can not be achieved at the
selected shutter speed, aperture will be displayed in
red. Adjust shutter speed until the correct exposure
is achieved. If the subject is outside the metering
range of the camera, the aperture display will show
“F---”. Press the shutter button halfway to measure
exposure again.
• The shutter speed is restricted depending on the ISO
setting.
Aperture
29
Shooting Mode
M: MANUAL
C: CUSTOM MODE
In this mode, you choose both shutter
speed and aperture. If desired, exposure can be altered from the value suggested by the camera.
Rotate the command dial to M
set the shutter speed. Press
and hold the d button and Shutter speed
rotate the command dial to set 250 F4.5
the aperture value.
In P, S, A, M and all O modes except R, the K CUSTOM SET option
in the shooting menu (P 83) can be
used to save current camera and menu
settings. These settings are recalled
whenever the mode dial is rotated to C
(custom mode).
Aperture
3 Cautions
• Noise in the form of randomly-spaced bright pixels
may occur in long exposures.
• The shutter speed is restricted depending on the ISO
setting.
The Exposure Indicator
The amount the picture will be under- or over-exposed at current settings is shown by the exposure
indicator.
250
30
F4.5
Menu/setting
Settings saved
N ISO, O IMAGE SIZE, T IMAGE QUALITY, U DYNAMIC RANGE, P FILM SIMULATION, d WB SHIFT, f COLOR, e TONE,
Shooting H SHARPNESS, h NOISE REDUCTION,
menu
b FACE DETECTION, n FACE RECOGNITION, F MOVIE AF MODE, W MOVIE
MODE, 2 ELECTRONIC LEVEL, J AE BKT
EV STEPS, I FLASH, g EXTERNAL FLASH
Setup menu C AF ILLUMINATOR, j RAW
ISO, metering, autofocus mode, focus mode,
white balance, burst mode, macro mode, flash
Other
mode, exposure compensation, monitor display options (DISP/BACK button)
Focus Lock
To compose photographs with off-center subjects:
1 Position the subject in the focus frame.
Focus.
2 Press
the shutter button
the picture.
3 Recompose
Keeping the shutter button pressed halfway, recompose the picture.
4 Shoot.
More on Photography
halfway to set focus and
exposure. Focus and exposure will remain locked
while the shutter button
is pressed halfway (AF/AE
lock).
Autofocus
Although the camera boasts a high-precision autofocus system, it may be unable to focus on the subjects
listed below. If the camera is unable to focus using
autofocus, use focus lock to focus on another subject
at the same distance and then recompose the photograph.
• Very shiny subjects such as mirrors or car bodies.
• Fast-moving subjects.
• Subjects photographed through a window or other
reflective object.
• Dark subjects and subjects that absorb rather than
reflect light, such as hair or fur.
• Insubstantial subjects, such as smoke or flame.
• Subjects that show little contrast with the background (for example, subjects in clothing that is the
same color as the background).
• Subjects positioned in front of or behind a highcontrast object that is also in the focus frame (for
example, a subject photographed against a backdrop of highly contrasting elements).
31
The AE/AF LOCK Button
The AE/AF LOCK button can be used to lock exposure or focus.
Locking Exposure
Meter exposure.
Position the subject in the
focus frame and press the
AE/AF LOCK button to meter exposure.
1
Focus.
2 Keeping
the AE/AF LOCK
+
button pressed, press the
shutter button halfway
to focus. Focus and exposure will remain locked while the shutter
button is pressed halfway, even if you later
release the AE/AF LOCK button.
Repeat steps 1 and 2 as desired to refocus
before taking the picture.
32
the picture.
3 Recompose
Keeping the shutter button pressed halfway,
recompose the picture.
c Caution
Adjusting zoom ends AE lock. AE lock is not available with Intelligent Face Detection.
4 Shoot.
Locking Focus
If AF LOCK ONLY is selected for v AE/AF-LOCK
BUTTON in the setup menu (P 96), pressing the
AE/AF LOCK button locks focus. If AE/AF LOCK is
selected, both focus and exposure will be locked.
a Note
If AE&AF ON/OFF SWITCH is selected for k AE/AFLOCK MODE in the setup menu (P 96), exposure
and/or focus will lock when the AE/AF LOCK button is
pressed and remain locked until the button is pressed
again.
F Macro and Super Macro Modes (Close-ups)
For close-ups, press the selector left (F) to choose from the macro options shown below.
OFF
OFF
Choose from F (macro mode),
G (super macro mode), or
OFF (macro mode off)
When macro mode is in effect, the camera focuses on subjects near the center of the frame. Use the
zoom ring to compose pictures. The following restrictions apply in super macro mode: the lens must
be zoomed all the way out (at other zoom positions, o is displayed) and the flash can not be used.
More on Photography
1 Notes
• Use of a tripod is recommended to prevent blur caused by camera shake.
• Flash compensation may be required when using the flash (P 82).
• Using the flash at close range may cast a lens shadow. Zoom a little or have more distance from the subject.
33
N Using the Flash (Super-Intelligent Flash)
When the flash is used, the camera’s Super-Intelligent Flash system instantly analyzes the scene based
on such factors as the brightness of the subject, its position in the frame, and its distance from the
camera. Flash output and sensitivity are adjusted to ensure that the main subject is correctly exposed
while preserving the effects of ambient background lighting, even in dimly-lit indoor scenes. Use the
flash when lighting is poor, for example when shooting at night or indoors under low light.
the flash.
1 Raise
Press the flash pop-up button to raise the flash.
Turning the Flash Off
Lower the flash where flash photography is prohibited or to capture natural lighting
under dim light. At slow shutter speeds, k will be displayed to warn that pictures
may be blurred; use of a tripod is recommended.
a flash mode.
2 Choose
Press the selector right (N). The flash mode changes each time the selector is pressed.
Mode
A/K
(AUTO FLASH)
N/L
(FORCED FLASH)
O/M
(SLOW SYNCHRO)
34
Description
The flash fires when required. Recommended in most situations.
The flash fires whenever a picture is taken. Use for backlit subjects or for natural
coloration when shooting in bright light.
Capture both the main subject and the background under low light (note that
brightly lit scenes may be overexposed).
N Using the Flash (Super-Intelligent Flash)
3 Caution
The flash may fire several times with each shot. Do not move the camera until shooting is complete.
1 Note
The peripheral part of an image may be dark when using the flash.
Red-Eye Removal
When Intelligent Face Detection is active (P 48), and ON is selected for B RED EYE REMOVAL in
the setup menu (P 96), red-eye removal is available in K, L, and M.
Red-eye removal minimizes “red-eye” caused when light from the flash is reflected from the subject’s
retinas as shown in the illustration at right.
More on Photography
35
J Using the Self-Timer
To use the self-timer, press the selector down (h) and choose from the following options:
OFF
OFF
Option
T (OFF)
Description
Self-timer off.
The shutter is released automatically when the camera detects a human portrait subject
o (AUTO RELEASE)
facing the camera. Use for portraits of babies.
The shutter is released ten seconds after the shutter button is pressed. Use for self-portraits.
The self-timer lamp on the front of the camera lights when the timer starts and begins to
S (10 SEC)
blink shortly before the photo is taken.
The shutter is released two seconds after the shutter button is pressed. Use to reduce blur
caused by the camera moving when the shutter button is pressed. The self-timer lamp will
R (2 SEC)
blink as the timer counts down.
36
d Exposure Compensation
Use exposure compensation when photographing very bright, very dark, or high-contrast subjects.
Press the d button and rotate the command dial
until the exposure indicator shows the desired
value.
P
+
1 Note
A d icon and exposure indicator are displayed at settings other than ±0. Exposure compensation is not
reset when the camera is turned off; to restore normal
exposure control, choose a value of ±0.
Exposure indicator
250
F4.5
More on Photography
The effect is visible in the display.
Choose negative values Choose positive values to
to reduce exposure
increase exposure
(“–” sign turns yellow)
(“+” sign turns yellow)
37
Sensitivity
The camera’s sensitivity to light can be adjusted by pressing the ISO button and rotating the command
dial until the desired value is highlighted in the display.
ISO
+
100
200 400 800 1600 3200
100
ISO
Higher values can reduce blur; note, however, that mottling may appear in pictures taken at high sensitivities.
100
Bright
Less noticeable
Option
AUTO
AUTO (3200) / AUTO (1600) /
AUTO (800) / AUTO (400)
12800 / 6400 / 3200 / 1600 /
800 / 400 / 200 / 100
38
ISO
Scene
Noise (mottling)
12800
Dark
More noticeable
Description
Sensitivity is adjusted automatically in response to shooting conditions.
As above, except that sensitivity will not be raised above the value in parentheses.
Sensitivity is set to the specified value, which is shown in the display.
Metering
To choose how the camera meters exposure when Intelligent Face Detection is off, press the AE button
and rotate the command dial.
PHOTOMETRY
+
MULTI
Description
Automatic scene recognition is used to adjust exposure for a wide range of shooting conditions.
The camera meters lighting conditions at the center of the frame. Recommended when the background is much brighter or darker than the main subject.
Exposure is set to the average for the entire frame. Provides consistent exposure across multiple
q
shots with the same lighting, and is particularly effective for landscapes and portraits of subjects
(AVERAGE)
dressed in black or white.
More on Photography
Option
o
(MULTI)
p
(SPOT)
39
Autofocus Mode
To choose how the camera selects the focus area
when K is selected for focus mode (P 41), press
the AF button and rotate the command dial. Note
that regardless of the option selected, the camera will focus on the subject in the center of the
monitor when macro mode is on (P 33).
AF MODE
+
CENTER
The following options are available:
• r (CENTER): The camera fo- M
cuses on the subject in the
center of the frame. This option can be used with focus 250
lock.
• s (MULTI): When the shutter
button is pressed halfway,
the camera detects highcontrast subjects near the
center of the frame and selects the focus area automatically.
40
F4.5
Focus frame
• t (AREA): The focus position SELECT AF AREA
can be chosen manually by
pressing the selector up,
down, left, or right and pressSET Focus
CANCELtarget
ing MENU/OK when the focus
brackets are in the desired position. Choose for
precise focus when the camera is mounted on a
tripod.
• x (TRACKING): Position the M
subject in the focus target
and press the selector left.
TRACKING
The camera will track the 250STARTF4.5
subject and adjust focus as it
moves through the frame.
Focus Mode
To choose how the camera focuses, press the AF C-S-M button and rotate the command dial.
FOCUSING
+
CONTINUOUS AF
The following options are available:
Description
Focus locks while the shutter button is pressed halfway. Choose for stationary subjects.
The camera continually adjusts focus to reflect changes in the distance to the subject even
when the shutter button is not pressed halfway (note that this increases the drain on the
J
batteries). r (CENTER) is automatically selected for autofocus mode (P 40); if Intelligent
(CONTINUOUS AF)
Face Detection is on, the camera will continually adjust focus for the selected face. Choose
for moving subjects.
Focus manually using the focus ring. Rotate the ring left to reduce the focus distance, right
to increase. The manual focus indicator indicates how closely the focus distance matches
the distance to the subject in the focus brackets. Choose for manual control of focus or in
situations in which the camera is unable to focus using autofocus (P 31). Intelligent Face
Detection turns off automatically.
j
P
Manual focus
(MF)
More on Photography
Mode
K
(SINGLE AF)
mode icon
Reduce focus
distance
Increase focus
distance
Manual focus
indicator
41
Focus Mode
a Notes: Manual Focus
• Use of a tripod is recommended. Focus may be affected if the camera moves.
• If ON is selected for j FOCUS CHECK in the setup menu (P 97), the whole image will be magnified to assist
focus when the focus ring is rotated.
• The camera will not focus when the focus ring is rotated all the way to the right. To focus at infinity, focus on a
distant object.
• To focus using autofocus (P 40), press the AE/AF LOCK button. This can be used to quickly
focus on a chosen subject in manual focus mode.
42
White Balance
For natural colors, press the WB button and rotate the command dial until a setting that matches the light source is highlighted in the display.
Description
White balance adjusted automatically.
Measure a value for white balance.
For subjects in direct sunlight.
For subjects in the shade.
Use under “daylight” fluorescent lights.
Use under “warm white” fluorescent lights.
Use under “cool white” fluorescent lights.
Use under incandescent lighting.
h: Custom White Balance
Choose h to adjust white balance for unusual lighting conditions. White balance measurement options will
be displayed; frame a white object so that it fills the LCD monitor and press the shutter button all the way down
to measure white balance.
• If “COMPLETED!” is displayed, press MENU/OK to set white balance to the measured value.
• If “UNDER” is displayed, raise exposure compensation (P 37) and try again.
• If “OVER” is displayed, lower exposure compensation and try again.
More on Photography
Option
AUTO
h
i
j
k
l
m
n
+
1 Note
For greater precision, adjust P FILM SIMULATION, N ISO, and U DYNAMIC RANGE before measuring
white balance.
1 Notes
• At settings other than h, auto white balance is used with the flash.
• Results vary with shooting conditions. Play pictures back after shooting to check colors in the LCD monitor.
43
I Continuous Shooting (Burst Mode)
Capture motion or automatically vary selected settings over a series of pictures.
Press the I button and rotate the command dial
to choose from the options below:
+
CONTINUOUS
OFF
44
OFF
OFF: OFF
I: TOP
P: BEST FRAME CAPTURE
O: AE BKT
X: FILM SIMULATION BKT
Y: DYNAMIC RANGE BKT
1 Notes
• Focus and exposure are determined by the first frame
in each series. The flash turns off automatically; the
previously-selected flash mode is restored when continuous shooting is turned off.
• Frame rate varies with shutter speed.
• The number of pictures that can be taken in a single
burst varies with the scene and camera settings. The
number of pictures that can be recorded depends on
the memory available.
I Continuous Shooting (Burst Mode)
■ I TOP n
The camera takes photographs while the shutter
button is pressed. To choose the frame rate and
maximum number of shots per burst:
the selector right
1 Press
when the camera is in
shooting mode.
CONTINUOUS SHOOTING SETUP
SHOOTING SPEED
NUMBER OF FRAMES
4
Highlight the current frame rate and press the
2 selector
right, then press selector up or down
to choose a new value and press MENU/OK to
select.
3 Caution
Some frame rates may reduce the number of shots
available in Step 3.
Highlight the number of
3 shots
Highlight the current frame
2 rate
and press the selecor number of shots and press the selector
DISP/BACK to return to shooting mode
3 Press
when settings are complete.
■ P BEST FRAME CAPTURE
The camera takes a series of pictures, starting
before and ending after the shutter button is
pressed. To choose the frame rate and number
of shots:
CONTINUOUS SHOOTING SETUP
tor right. Press the selector
16
8 FRAMES
up or down to choose the
number of shots in each
SET
CANCEL
burst and left or right to
choose their distribution Distribution
(the number on the left is taken before and the
number on the right after the shutter button
is pressed). Press MENU/OK when settings are
complete.
–1S
SHUTTER
1S
More on Photography
right, then press selector up or down to choose
a new value and press MENU/OK to select.
Shots per burst
Press the selector right when the camera is in
1 shooting
mode.
45
I Continuous Shooting (Burst Mode)
4 Press DISP/BACK to return to shooting mode.
photographs. The camera begins record5 Take
ing while the shutter button is pressed halfway, and completes the burst when the shutter button is pressed all the way down. The
illustration shows a burst of eight shots, three
before the shutter button is pressed and four
after.
Shutter button
Shutter button pressed all the
way down
pressed halfway
“Before”
shots
46
“After”
shots
3 Cautions
• If the shutter button is pressed all the way down before the number of frames selected for the “before”
portion is recorded, the remaining frames will be
taken after the shutter button is pressed all the way
down.
• If the shutter button is pressed halfway for an extended period, the camera may record the burst before
the shutter button is pressed all the way down.
■ O AE BKT
Each time the shutter button is pressed, the camera takes three shots: one using the metered value for exposure, the second overexposed by the
amount selected for J AE BKT EV STEPS in the
shooting menu (P 82), and the third underexposed by the same amount (the camera may not
be able to use the selected bracketing increment
if the amount of over- or under- exposure exceeds
the limits of the exposure metering system).
I Continuous Shooting (Burst Mode)
■ X FILM SIMULATION BKT
Each time the shutter button is pressed, the
camera takes three shots at different P FILM
SIMULATION settings (P 80): c PROVIA/
STANDARD for the first, d Velvia/VIVID for the
second, and e ASTIA/SOFT for the third.
R CONTINUOUS
I TOP n
P BEST FRAME
CAPTURE
O AE BKT
X FILM SIMULATION BKT
Y DYNAMIC
RANGE BKT
RAW+JPEG
Up to 6
j RAW
RAW
Up to 6
OFF (JPEG)
Up to 32
Up to 6
Up to 6
Up to 16
3
3
3
—
—
3
—
—
3
More on Photography
■ Y DYNAMIC RANGE BKT
Each time the shutter button is pressed, the camera takes three shots at different U DYNAMIC
RANGE settings (P 80): A 100% for the first,
B 200% for the second, and C 400% for
the third (N ISO can not exceed 3200; values less
than 400 are not available when O is selected for
O IMAGE SIZE).
j RAW
The number of pictures that can be recorded in a single burst varies with the option selected for j RAW
in the setup menu.
47
b Intelligent Face Detection
Intelligent Face Detection allows the camera to automatically detect human faces and set focus and
exposure for a face anywhere in the frame for shots that emphasize portrait subjects. Choose for group
portraits (in horizontal or vertical orientations) to prevent the camera from focusing on the background.
To use Intelligent Face Detection, press MENU/OK to display
the shooting menu and select ON for b FACE DETECTION. Faces can be detected
Green border
with the camera in vertical or
horizontal orientation; if a face is detected, it will be
indicated by a green border. If there is more than
one face in the frame, the camera will select the
face closest to the center; other faces are indicated
by white borders.
3 Cautions
• In some modes, the camera may set exposure for the
frame as a whole rather than the portrait subject.
• If the subject moves as the shutter button is pressed,
their face may not be in the area indicated by the
green border when the picture is taken.
48
Intelligent Face Detection
Intelligent Face Detection is
recommended when using
the self-timer for group- or
self-portraits (P 36).
7
When a picture taken with Intelligent Face Detection
is displayed, the camera can automatically select faces
for red-eye removal (P 86), playback zoom (P 53),
slide shows (P 85), image search (P 57), image disp.
(P 93), printing (P 66), and cropping (P 87).
n Face Recognition
The camera can store information on the face
and personal details (name, relationship, and
birth date) of portrait subjects and assign these
subjects priority for Intelligent Face Detection or
display their names and other information during
playback.
Adding New Faces
Select REGISTER.
1 Select
REGISTER for n FACE RECOGNITION in the shooting menu.
1 Note
To disable face recognition, select OFF.
a photograph.
2 Take
After checking that
the
subject is facing the camera, frame the subject using the guides and take
the photograph.
REGISTER FACE
face recognition data.
3 Enter
Press MENU/OK to display face recognition
data and enter the following information:
• NAME: Enter a name of up to 14 characters
and press MENU/OK.
• BIRTHDAY: Enter the subject’s date of birth
and press MENU/OK.
• CATEGORY: Choose the option that describes
your relationship to the subject and press
MENU/OK.
1 Note
If you attempt to zoom in on the face of a person indicated by a green border in the face recognition database on their birthday, the camera will display their
name and the message “Happy Birthday!”.
More on Photography
Follow the steps below to add faces to the face
recognition database.
1 Note
If an error is displayed, take the photograph
again.
CAPTURE THE FACE
ALONG WITH THE GUIDLINE
CANCEL
49
n Face Recognition
Viewing, Editing, and Deleting Existing Data
Adding Faces Automatically
Follow the steps below to view, edit, or delete
face recognition data.
To automatically add frequently-photographed
subjects to the face recognition database, select
ON for AUTO REGISTRATION in the face recognition menu. If the camera detects a face that has
been photographed many times without being
added to the database, it will display a message
prompting you to create a new face recognition
entry. Press MENU/OK and enter face recognition
data.
Select VIEW & EDIT for n FACE RECOG1 NITION.
2 Select a face.
or edit face recognition data.
3 View
The name, category, or birth date can be edited as described in Step 3 of “Adding New
Faces” (P 49). To retake the photo, select
REPLACING IMAGE and shoot a new portrait as described above.
1 Note
To delete face recognition data for the selected subject, select ERASE.
50
1 Note
The camera may sometimes fail to recognize new faces
automatically. If necessary, faces can be added manually using the REGISTER option.
n Face Recognition
Face Recognition
The camera can store up to eight faces. If you attempt
to add a ninth face, a confirmation dialog will be displayed; use VIEW & EDIT to make room for new faces
by deleting existing data. AUTO REGISTRATION is
disabled if there are already data for eight faces.
3 Caution
The camera may fail to identify subjects in the face
recognition database if they are not facing the camera or are only partly in the frame, or if details of the
subjects’ faces or expressions differ markedly from
those in the database.
More on Photography
When Intelligent Face Detection (P 48) is on and
the frame contains multiple subjects from the face
recognition database, the camera displays the name
of the subject that will be used to set focus and exposure (the subject shown by the green frame). If no
name is entered, the camera will show “---”. Subjects
identified using face recognition but not used to set
focus and exposure are shown by orange frames,
other subjects by white frames.
51
Playback Options
To view the most recent picture in the monitor,
press the a button.
100-0001
Continuous Shooting
In the case of pictures taken in continuous shooting mode, only the first frame of each series will
be displayed. Press the selector down to view the
other pictures in the series.
I Favorites: Rating Pictures
More on Playback
Press the selector right to view pictures
in the order recorded, left to view pictures in reverse order. Keep the selector
pressed to scroll rapidly to the desired
frame.
To rate the picture currently displayed in full-frame
playback, press DISP/BACK and press the selector
up and down to select from zero to five stars.
1 Note
Pictures taken using other cameras are indicated by a m (“gift image”) icon during playback.
52
Playback Options
Playback Zoom
Press k to zoom in on pictures displayed in single-frame playback; n to zoom out. When the
picture is zoomed in, the selector can be used to
view areas of the image not currently visible in the
display.
Zoom indicator
Intelligent Face Detection
Pictures taken with Intelligent
Face Detection (P 31) are indicated by a g icon. Press the
g button to zoom in on the
ZOOM
BACK
subject selected with Intelligent Face Detection. You can
then use the k and n buttons to zoom in and out.
Navigation window
shows portion of image
currently displayed in
monitor
1 Note
The maximum zoom ratio varies with image size. Playback zoom is not available with cropped or resized
copies saved at a size of a or smaller.
More on Playback
Press DISP/BACK or MENU/OK to exit zoom.
53
Playback Options
Multi-Frame Playback
To change the number of images displayed, press
n in single-frame view.
12/31/2050
2 Tip: Two-Frame Display
Two-frame display can be used
to compare pictures taken in
C mode.
10 : 00 AM
Press k to view
fewer images.
Press n to view
more images.
54
Use the selector to highlight images and press
MENU/OK to view the highlighted image full frame.
In the nine- and hundred-frame displays, press
the selector up or down to view more pictures.
A Deleting Pictures
To delete individual pictures, multiple selected pictures, or all pictures, press MENU/OK, select A ERASE (P 84), and choose from the
options below. Note that deleted pictures can not be recovered. Copy
important pictures to a computer or other storage device before proceeding.
Option
FRAME
SELECT FRAMES
BACK
FRAME
SELECTED FRAMES
ALL FRAMES
SET
Description
Press the selector left or right to scroll through pictures and press MENU/OK to delete the current
picture (a confirmation dialog is not displayed).
Highlight pictures and press MENU/OK to select or deselect (pictures included in the photobook
or print order are shown by S). When the operation is complete, press DISP/BACK to display a
confirmation dialog, then highlight OK and press MENU/OK to delete the selected pictures.
A confirmation dialog will be displayed; highlight OK and press MENU/OK to delete all unprotected pictures (if a memory card is inserted, only the pictures on the memory card will be affected; the pictures in internal memory are only deleted if no memory card is inserted). Pressing
DISP/BACK cancels deletion; note that any pictures deleted before the button was pressed can
not be recovered.
1 Notes
• Protected pictures can not be deleted. Remove protection from any pictures you wish to delete (P 86).
• If a message appears stating that the selected images are part of a DPOF print order, press MENU/OK to delete the
pictures.
More on Playback
ALL FRAMES
PLAYBACK MENU
ERASE
55
Viewing Photo Information
To view or hide the photo information listed below in single-frame playback, press info.
Histograms
Histograms show the distribution of tones in the image. Brightness is shown by the horizontal axis, the
number of pixels by the vertical axis.
No. of
pixels
4:3 N
ISO 400
F4.5
1/250
:
: OFF
:
: -1 2 3
12/31/2050 10 : 00 AM
100-0001
q Dynamic range w Image size and quality
e Sensitivity
r Shutter speed/aperture
t Film simulation y Flash mode u White balance
i Exposure compensation o Frame number
!0 Picture (overexposed areas blink on and off )
!1 Histogram
56
Pixel brightness
Shadows
Highlights
Optimal exposure: Pixels are distributed in an even curve throughout the tone range.
Overexposed: Pixels are clustered
at the right side of the graph.
Underexposed: Pixels are clustered
at the left side of the graph.
Image Search
Search for images by various criteria.
1 Press the H button during playback.
a search condition. Only pictures that
3 Select
match the search condition will be displayed.
To delete or protect selected pictures or to
view the selected pictures in a slide show,
press MENU/OK and choose from the following
options:
Option
one of the following options and
2 Highlight
press MENU/OK:
Option
See page
84
86
85
4 To end the search, select EXIT SEARCH.
More on Playback
Description
Find all pictures taken on a selected
BY DATE
date.
Find all pictures based on specified face
BY FACE
information.
Find all pictures with a specified rating
BY I FAVORITES
(P 52).
Find all pictures that match a selected
BY SCENE
scene.
BY TYPE OF DATA Find all still pictures or all movies.
Find all pictures selected for upload to a
BY UPLOAD MARK
specified destination (P 84).
A ERASE
D PROTECT
I SLIDE SHOW
57
X PhotoBook Assist
Create books from your favorite photos.
Creating a PhotoBook
Select X PHOTOBOOK ASSIST in the play- 5 Scroll through the images and press the selec1 back
tor up to select or deselect the current image
menu.
2 Highlight NEW BOOK.
for inclusion in the book. To display the current
image on the cover, press the selector down.
MENU/OK to display the new
3 Press
book dialog.
1 Note
The first picture selected automatically becomes
the cover image. Press the selector down to select
a different picture for the cover.
pictures for the new book.
4 Choose
• SELECT FROM ALL: Choose from all the
pictures available.
• SELECT BY IMAGE SEARCH: Choose from pictures
matching selected search conditions (P 57).
1 Note
Neither photographs a or smaller nor movies can
be selected for photobooks.
MENU/OK to exit when the book
6 Press
is complete.
7 Highlight COMPLETE PHOTOBOOK.
SELECT IMAGES FOR PHOTOBOOK
SELECT ALL
COMPLETE PHOTOBOOK
EXIT
1 Note
Choose SELECT ALL to select all photos, or all photos matching the specified search conditions, for
the book.
58
X PhotoBook Assist
Press MENU/OK. The new book will be
8 added
to the list in the photobook
assist menu.
3 Cautions
• Photobooks can contain up to 300 pictures.
• Books that contain no photos are automatically
deleted.
PhotoBooks
Photobooks can be copied to a computer using the
supplied MyFinePix Studio software.
Viewing PhotoBooks
Highlight a book in the photobook assist menu
and press MENU/OK to display the book, then press
the selector left and right to scroll through the
pictures. Press DISP/BACK to return to the photobook assist menu.
Editing and Deleting PhotoBooks
Display the photobook and press
1 MENU/OK
to view book edit options.
PhotoBook” on page 58.
• ERASE: Delete the current photobook.
3 Follow the on-screen instructions.
More on Playback
from the following options:
2 Choose
• EDIT: Edit the book as described in “Creating a
59
Viewing Panoramas
To view a panorama, display in single-frame view and press the selector down.
PLAY
STOP
PAUSE
The following operations can be performed during playback:
Operation
Start/pause
playback
End playback
60
Button
Description
Press the selector down to start playback. Press again to pause.
Press the selector up to end playback.
Recording Movies
Press z to shoot a movie. During recording, the following indicators will be displayed and sound will
be recorded via the built-in microphone (be careful not to cover the microphone during recording).
y REC icon
REC
1
999m59s
F
Number of photos that
can be taken during
recording
Time remaining
To end recording, press the z button again. Recording ends automatically when the movie reaches
maximum length or memory is full.
Movies
1 Notes
• Zoom can be adjusted while recording is in progress.
• If the subject is poorly lit, the AF-assist lamp may light to assist the focus operation.
To turn the AF-assist lamp off , select OFF for C AF ILLUMINATOR in the setup menu (P 96).
• Focus, exposure, and white balance are adjusted automatically throughout recording. The color and brightness
of the image may vary from that displayed before recording begins.
• Sounds made by the camera may be recorded.
61
Recording Movies
Taking Photographs During Recording
Press the shutter button to take a photograph during recording.
1 Notes
• If O is selected for O IMAGE SIZE, the picture
will be recorded at size P.
• The photo is saved separately from the movie and
does not appear as part of the movie.
3 Cautions
• Photos can not be taken while a high-speed movie
is being recorded.
• The number of photos that can be taken is limited.
3 Cautions
• The indicator lamp lights while movies are being recorded. Do not open the battery chamber during
shooting or while the indicator lamp is lit. Failure
to observe this precaution could prevent the movie
from being played back.
• Vertical or horizontal streaks may appear in movies
containing very bright subjects. This is normal and
does not indicate a malfunction.
• The temperature of the camera may rise if it is used to
record movies for an extended period or if the ambient temperature is high. This is normal and does not
indicate a malfunction.
62
Movie Frame Size
Before recording, select a frame size using the
W MOVIE MODE option in the shooting menu
(P 82).
Option
Description
i 1920 (1920 × 1080) Full HD (High Definition).
h 1280 (1280 × 720) High Definition.
Standard definition.
f (640 × 480)
High speed movie. Sound is not
Y 640 × 480 (80fps)
recorded, and focus, exposure, and
white balance are not adjusted auY 320 × 240 (160fps)
tomatically. Black bands appear at
the top and bottom of movies reY 320 × 112 (320fps)
corded at Y 320 × 112.
a Viewing Movies
During playback (P 52),
movies are displayed in the
monitor as shown at right.
The following operations
can be performed while a
movie is displayed:
Operation
100-006
12/31/2050
PLAY
10 : 00 AM
STOP
5m42s
PAUSE
2 Tip: Viewing Movies on a Computer
Copy movies to the computer before viewing.
3 Caution
Do not cover the speaker during playback.
Movies
Description
Press the selector down to start playback.
Start/ Press again to pause. While playback is
pause paused, you can press the selector left or
playback right to rewind or advance one frame at
a time.
End
playback/ Press the selector up to end playback.
delete
Adjust Press the selector left or right to adjust playspeed back speed during playback.
Press MENU/OK to pause playback and display volume controls. Press the selector
Adjust
up or down to adjust the volume and
volume
press MENU/OK to exit. Volume can also be
adjusted from the setup menu.
Playback Speed
Arrow
Press the selector left or right to
adjust playback speed. Speed is
shown by the number of arrows
(M or N).
63
Viewing Pictures on TV
Connect the camera to a TV to show pictures to a group.
1 Turn the camera off.
2 Connect the supplied A/V cable as shown below.
Insert into A/V
cable connector
Connect white plug
to audio-in jack
Connect yellow plug
to video-in jack
HDMI
An HDMI cable (available from third-party suppliers; P 99) can be used to connect the camera to High Definition (HD) devices (playback only). The USB cable can not be used while an HDMI cable is connected.
Insert into HDMI
connector
Connections
64
HDMI Mini Connector
Insert into HDMI
connector
Viewing Pictures on TV
Tune the television to the video or HDMI input channel. See the documentation supplied with the
3 television
for details.
the camera on and press the a button. The camera monitor turns off and pictures and mov4 Turn
ies are played back on the TV. Note that the camera volume controls have no effect on sounds
played on the TV; use the television volume controls to adjust the volume.
1 Note
Image quality drops during movie playback.
3 Caution
When connecting the cable, be sure the connectors are fully inserted.
Connections
65
Printing Pictures via USB
If the printer supports PictBridge, the camera can be connected directly to the printer and
pictures can be printed without first being copied to a computer. Note that depending on
the printer, not all the functions described below may be supported.
Connecting the Camera
Printing Selected Pictures
the supplied USB cable as shown and 1 Press the selector left or right to dis1 Connect
play a picture you wish to print.
turn the printer on.
the selector up or down to
2 Press
choose the number of copies (up to
99).
steps 1–2 to select additional
3 Repeat
pictures. Press MENU/OK to display a
the camera on and press the a button.
2 Turn
t USB will be displayed in the monitor, followed by the PictBridge display shown below
at right.
USB
PICTBRIDGE
TOTAL: 00000
66
PRINT THESE FRAMES
TOTAL: 9 SHEETS
YES
CANCEL
4 Press MENU/OK to start printing.
00 SHEETS
FRAME
OK
confirmation dialog when settings
are complete.
SET
Printing Pictures via USB
2 Tip: Printing the Date of Recording
To print the date of recording on pictures, press DISP/
BACK in steps 1–2 to display the PictBridge menu (see
“Printing the DPOF Print Order,” below). Press the selector up or down to highlight PRINT WITH DATE s
and press MENU/OK to return to the PictBridge display
(to print pictures without the date of recording, select
PRINT WITHOUT DATE).
1 Note
If no pictures are selected when the MENU/OK button is
pressed, the camera will print one copy of the current
picture.
Printing the DPOF Print Order
To print the print order created with K PRINT
ORDER (DPOF) in the playback menu (P 89):
In the PictBridge display, press DISP/
1 BACK
to open the PictBridge menu.
PICTBRIDGE
PRINT WITH DATE
PRINT WITHOUT DATE
PRINT DPOF
the selector up or down to
2 Press
highlight u PRINT DPOF.
Press MENU/OK to display a confirma3 tion
dialog.
YES
CANCEL
Connections
PRINT DPOF OK?
TOTAL: 9 SHEETS
67
Printing Pictures via USB
4 Press MENU/OK to start printing.
During Printing
The message shown at right
is displayed during printing.
Press DISP/BACK to cancel before all pictures are printed
(depending on the printer,
printing may end before the
current picture has printed).
PRINTING
CANCEL
If printing is interrupted, turn the camera off and then
on again.
Disconnecting the Camera
Confirm that “PRINTING” is not displayed in the monitor and turn the camera off. Disconnect the USB
cable.
68
1 Notes
• Pictures can be printed from internal memory or a
memory card that has been formatted in the camera.
• If the printer does not support date printing, the
PRINT WITH DATE s option will not be available in
the PictBridge menu and the date will not be printed
on the pictures in the DPOF print order.
• When pictures are printed via direct USB connection,
page size, print quality, and border selections are
made using the printer.
Printing Pictures via USB
Creating a DPOF Print Order
The K PRINT ORDER (DPOF) option in the playback menu can be used to create a digital “print
order” for PictBridge-compatible printers (P 99)
or devices that support DPOF.
■ WITH DATE s// WITHOUT DATE
Select playback mode and press
MENU/OK to display the playback
menu.
DPOF
DPOF (Digital Print Order Format) is a standard that allows pictures to be printed from
“print orders” stored in internal memory or
on a memory card. The information in the
order includes the pictures to be printed, date imprint, and the number of copies of each picture.
Highlight K PRINT ORDER (DPOF)
2 and
press MENU/OK.
1
Highlight one of the following op3 tions
and press MENU/OK:
• WITH DATE s: Print the date of recording on pictures.
• WITHOUT DATE: Do not print the date
of recording on pictures.
or remove from the print order.
Connections
Press the selector left or right to dis4 play
a picture you wish to include in
69
Printing Pictures via USB
the selector up or down to
5 Press
choose the number of copies (up to
99). To remove a picture from the
order, press the selector down until the number of copies is 0.
PRINT ORDER (DPOF)
DPOF: 00001
Total number of prints
Number of copies
steps 4–5 to complete the
6 Repeat
print order. Press MENU/OK to save
the print order when settings are
complete, or DISP/BACK to exit without changing the print order.
The total number of prints is dis7 played
in the monitor. Press MENU/OK
to exit.
01 SHEETS
FRAME
SET
2 Tip: Intelligent Face Detection
If the current picture was created with Intelligent
Face Detection, pressing g sets the number of
copies to the number of faces detected.
1 Note
When pictures are printed via direct USB connection, page size, print quality, and border selections
are made using the printer.
70
The pictures in the current
print order are indicated by a
u icon during playback.
Printing Pictures via USB
1 Notes
• Remove the memory card to create or modify a print
order for the pictures in internal memory.
• Print orders can contain a maximum of 999 pictures.
RESET DPOF OK?
• If a memory card is inserted
containing a print order created by another camera, the
message shown at right will
YES
NO
be displayed. Pressing MENU/
OK cancels the print order; a
new print order must be created as described above.
■ RESET ALL
RESET DPOF OK?
To cancel the current print
order, select RESET ALL
in the K PRINT ORDER
(DPOF) menu. The confirYES
CANCEL
mation shown at right will
be displayed; press MENU/OK to remove all pictures
from the order.
Connections
71
Viewing Pictures on a Computer
The supplied software can be used to copy pictures to a computer, where they can be stored, viewed,
organized, and printed. Before proceeding, install the software as described below. Do NOT connect the
camera to the computer until installation is complete.
Installing the Software
Two applications are supplied: MyFinePix Studio for Windows and FinePixViewer for the Macintosh.
Installation instructions for Windows are on pages 72–73, those for the Macintosh on pages 74–75.
Windows: Installing MyFinePix Studio
Confirm that the computer meets the following system requirements:
1
Windows 7 1
Windows Vista 1
3 GHz Pentium 4 or better
(2.4 GHz Core 2 Duo or better) 2
CPU
RAM
1 GB or more
Free disk space
Video
Other
•
•
•
•
Windows XP 1
2 GHz Pentium 4 or better
(2.4 GHz Core 2 Duo or better) 2
512 MB or more
(1 GB or more) 2
2 GB or more
15 GB or more
1024 × 768 pixels or more with 24-bit color or better
A graphics processing unit (GPU) that supports DirectX 7 or later
Built-in USB port recommended. Operation is not guaranteed with other USB ports.
Internet connection (broadband recommended) required to install .NET Framework (if necessary), to use
auto update feature, and when performing such tasks as sharing pictures on-line or via e-mail.
1 Other versions of Windows are not supported. Only pre-installed operating systems are supported; operation is not
guaranteed on home-built computers or computers that have been upgraded from earlier versions of Windows.
2 Recommended when displaying HD movies.
72
Viewing Pictures on a Computer
2 Start the computer. Log in to an account with administrator privileges before proceeding.
3 Exit any applications that may be running and insert the installer CD in a CD-ROM drive.
Windows 7/Windows Vista
If an AutoPlay dialog is displayed, click SETUP.EXE. A “User Account Control” dialog will then be displayed;
click Yes (Windows 7) or Allow (Windows Vista).
The installer will start automatically; click Install MyFinePix Studio and follow the on-screen instructions to install MyFinePix Studio.
If the Installer Does Not Start Automatically
If the installer does not start automatically, select Computer or My Computer from the Start menu, then
double-click the FINEPIX CD icon to open the FINEPIX CD window and double-click setup or SETUP.EXE.
prompted to install Windows Media Player, DirectX, or .NET Framework, follow the on-screen in4 Ifstructions
to complete installation.
number is printed at the top of the CD label for reference when updating the software or contacting
customer support.
Installation is now complete. Proceed to “Connecting the Camera” on page 76.
Connections
Remove the installer CD from the CD-ROM drive when installation is complete. Store the installer
5 CD
in a dry location out of direct sunlight in case you need to re-install the software. The version
73
Viewing Pictures on a Computer
Macintosh: Installing FinePixViewer
Confirm that the computer meets the following system requirements:
1
CPU
PowerPC or Intel (Core 2 Duo or better) *
Pre-installed versions of Mac OS X version 10.3.9–10.6
OS
(visit http://www.fujifilm.com/support/digital_cameras/compatibility/ for more information)
RAM
256 MB or more (1 GB or more) *
Free disk space A minimum of 200 MB required for installation with 400 MB available when FinePixViewer is running
Video
800 × 600 pixels or more with thousands of colors or better
Other
Built-in USB port recommended. Operation is not guaranteed with other USB ports.
* Recommended when displaying HD movies.
After starting the computer and quitting any applications that may be running, insert the installer
2 CD
in a CD-ROM drive and double-click Installer for Mac OS X.
installer dialog will be displayed; click Installing FinePixViewer to start installation. Enter an
3 An
administrator name and password when prompted and click OK, then follow the on-screen instructions to install FinePixViewer. Click Exit to quit the installer when installation is complete.
74
Viewing Pictures on a Computer
the installer CD from the CD-ROM drive. Note that you may be unable to remove the CD
4 ifRemove
Safari is running; if necessary, quit Safari before removing the CD. Store the installer CD in a dry
location out of direct sunlight in case you need to re-install the software. The version number is
printed at the top of the CD label for reference when updating the software or contacting customer
support.
OS X 10.5 or earlier: Open the “Applications” folder, start Image Capture, and select Preferences…
5 Mac
from the Image Capture application menu. The Image Capture preferences dialog will be displayed;
choose Other… in the When a camera is connected, open menu, then select FPVBridge in the
“Applications/FinePixViewer” folder and click Open. Quit Image Capture.
Mac OS X 10.6: Connect the camera and turn it on. Open the “Applications” folder and start Image
Capture. The camera will be listed under DEVICES; select the camera and choose FPVBridge from
the Connecting this camera opens menu and click Choose. Quit Image Capture.
Installation is now complete. Proceed to “Connecting the Camera” on page 76.
Connections
75
Viewing Pictures on a Computer
Connecting the Camera
If the pictures you wish to copy are stored on a 3 Turn the camera on and press the a button.
1 memory
card, insert the card into the camera
MyFinePix Studio or FinePixViewer will start
(P 11).
1 Note
Windows users may require the Windows CD when
starting the software for the first time.
3 Caution
Loss of power during transfer could result in loss of
data or damage to internal memory or the memory
card. Insert fresh or fully-charged batteries before
connecting the camera.
Turn the camera off and connect the supplied
2 USB
cable as shown, making sure the connectors are fully inserted. Connect the camera directly to the computer; do not use a USB hub
or keyboard.
76
automatically; follow the on-screen instructions to copy pictures to the computer. To exit
without copying pictures, click Cancel.
3 Caution
If the software does not start automatically, it may
not be correctly installed. Disconnect the camera
and reinstall the software.
For more information on using the supplied software, start the application and select the appropriate option from the Help menu.
Viewing Pictures on a Computer
3 Cautions
Disconnecting the Camera
After confirming that the indicator lamp is out, follow
the on-screen instructions to turn the camera off and
disconnect the USB cable.
Uninstalling the Supplied Software
Only uninstall the supplied software when it is no longer required or before beginning reinstallation. After
quitting the software and disconnecting the camera,
drag the “FinePixViewer” folder from “Applications”
into the Trash and select Empty Trash in the Finder
menu (Macintosh), or open the control panel and use
“Programs and Features” (Windows 7/Windows Vista)
or “Add or Remove Programs” (Windows XP) to uninstall MyFinePix Studio. Under Windows, one or more
confirmation dialogs may be displayed; read the contents carefully before clicking OK.
Connections
• If a memory card containing a large number of images
is inserted, there may be a delay before the software
starts and you may be unable to import or save images. Use a memory card reader to transfer pictures.
• Make sure that the computer does not display a message stating that copying is in progress and that the
indicator lamp is out before turning the camera off or
disconnecting the USB cable (if the number of images copied is very large, the indicator lamp may remain
lit after the message has cleared from the computer
display). Failure to observe this precaution could result in loss of data or damage to internal memory or
the memory card.
• Disconnect the camera before inserting or removing
memory cards.
• In some cases, it may not be possible to access pictures
saved to a network server using the supplied software
in the same way as on a standalone computer.
• The user bears all applicable fees charged by the
phone company or Internet service provider when
using services that require an Internet connection.
77
Using the Menus: Shooting Mode
Use the shooting menus to adjust shooting settings. The options available vary with the shooting mode selected.
Using the Shooting Menu
Press MENU/OK to display the shoot1 ing
menu.
the selector up or down to
2 Press
highlight the desired menu item.
Press the selector right to display op3 tions
for the highlighted item.
the selector up or down to
4 Press
highlight the desired option.
MENU/OK to select the high5 Press
lighted option.
Menus
78
DISP/BACK
6 Press
menu.
to exit from the
Shooting Menu Options
Default values are shown in square brackets [ ].
A E MODE
[[R
R]
Choose an option for E mode (P 22).
A Adv. MODE
[[i
i]
Choose an advanced shooting mode (P 23).
A SCENE POSITION
[[SP1:
SP1:L
L] [SP2:
[SP2:M
M]
Choose a scene for SP1/SP2 mode (P 25).
N ISO
[AUTO (800)]
Control the camera’s sensitivity to light (P 38).
O IMAGE SIZE
[[O
O 4 : 3]
3]
Choose the image size and
O 4:3
aspect ratio at which pictures
are recorded. Large pictures Size Aspect ratio
can be printed at large sizes with no drop in quality, while small pictures require less memory, allowing more pictures to be recorded.
Using the Menus: Shooting Mode
T IMAGE QUALITY
[N]
Choose how much image files are compressed.
Size Versus Aspect Ratio
Size
Option
Option
Prints at sizes up to
O 34 × 25 cm (13.5 × 10 in.)
P 24 × 18 cm (9.5 × 7 in.)
Q 17 × 13 cm (7 × 5 in.)
FINE
NORMAL
4 : 3: Pictures have
the same proportions as the camera display.
Aspect ratio
3 : 2: Pictures have
the same proportions as a frame
of 35 mm film.
16 : 9: Suited for
display on High
Definition (HD)
devices.
3
2
9
4
3
Description
Low compression. Select for higher image
quality.
High compression. Select this option to
store more pictures.
16
Menus
79
Using the Menus: Shooting Mode
U DYNAMIC RANGE
[AUTO]
Control contrast. Higher values are recommended for scenes that include both sunlight and deep
shade or for increased contrast with such subjects
as sunlight on water, brightly-lit autumn leaves,
portraits taken against a blue sky, and white objects or people wearing white; note, however, that
mottling may appear in pictures taken at higher
values. If AUTO is selected, the camera will automatically select values between 100% and 400%
in response to shooting conditions.
Option
AUTO
Description
A 100% Increase contrast when shooting
indoors or under overcast skies.
B 200%
C 400%
D 800%
M 1600%
Reduce loss of detail in highlights
and shadows when photographing high-contrast scenes.
1 Note
M 1600% and D 800% are available only when
D-RANGE PRIORITY is selected in E mode.
80
P FILM SIMULATION
[[c
c]
Simulate the effects of different types of film, including sepia and black-and-white.
Option
Description
Standard color reproduction. Suited to a
c PROVIA/
wide range of subjects, from portraits to
STANDARD
landscapes.
d Velvia/ A high-contrast palette of saturated colors, suited to nature photographs.
VIVID
e ASTIA/ A soft-toned palette of less saturated colors.
SOFT
Take pictures in black and white.
b B&W
Take pictures in sepia.
f SEPIA
Using the Menus: Shooting Mode
d WB SHIFT
White balance can be fine-tuned. Adjust the selected color axis (R–Cy=Red-Cyan or B-Ye=Blue–
Yellow) by +3 to –3 in increments of one.
f COLOR
Adjust color density (HIGH/MID/LOW).
[MID]
e TONE
Adjust contrast (HARD/STD/SOFT).
[STD]
H SHARPNESS
[STD]
Choose whether to sharpen or soften outlines
(HARD/STD/SOFT).
h NOISE REDUCTION
[STD]
Choose the amount of noise reduction (HIGH/
STD/LOW).
Z ADVANCED ANTI BLUR
[OFF]
Select ON to enable advanced anti blur in R
mode (P 22).
b FACE DETECTION
Choose whether the camera automatically detects and sets focus and exposure for human portrait subjects (P 48).
n FACE RECOGNITION
Add portrait subjects to the face recognition database. These subjects will be given priority during
Intelligent Face Detection, and their names and
other information can be viewed during playback
(P 49).
Menus
81
Using the Menus: Shooting Mode
F MOVIE AF MODE
[[u
u]
This option controls how the camera selects the
focus area for movies.
Option
Description
The camera focuses on the subject in
r CENTER
the center of the frame.
The camera continuously adjusts fou CONTINUOUS cus to reflect changes in the distance
to the subject in the focus frame.
1 Note
Note that in u mode, the camera focuses continuously, increasing the drain on the battery, and that the
sound of the camera focusing may be audible.
W MOVIE MODE
Choose a frame size for movies (P 62).
82
[i
[i]
J AE BKT EV STEPS
[±1/3]
Choose the size of the exposure bracketing increment used when O (AE bracketing) is selected in
continuous shooting mode (P 44).
Choose from increments of ±1/3 EV, ±2/3 EV, and
±1 EV (note that the camera may not be able to
use the selected bracketing increment if the
amount of over- or under- exposure exceeds the
limits of the exposure metering system).
I FLASH
[±0]
Adjust flash brightness. Choose from values between +2/3 EV and –2/3 EV. The default setting is ±0.
Note that the desired results may not be achieved
depending on shooting conditions and the distance to the subject.
Using the Menus: Shooting Mode
g EXTERNAL FLASH
[OFF]
Choose ON when using an optional flash unit (except Fujifilm products) mounted on the camera
hot shoe.
c Cautions
• The flash may not fully light the subject at speeds
faster than 1/1000 s.
• Use auto or custom white balance (P 43).
• If the built-in flash is raised when ON is selected for
g EXTERNAL FLASH, the built-in flash will fire once
to provide a signal for the optional flash unit to fire.
• External flash units can be used in P, S, A, M or O
(S and T only) modes.
• Fujifilm external flash units do not require this setting.
2 ELECTRONIC LEVEL
This option is useful to correct
for camera tilt. When ON is
selected, 2 lines are displayed
across the screen as shown. If
the lines stay perfectly overlapped, the camera is leveled.
[OFF]
Menus
a Notes
• The camera can be used with flash units that provide
aperture adjustment, external metering, and sensitivity control. Some flash units that are designed specifically for other cameras can not be used.
• For information on Fujifilm external flash units, see
Accessories from FUJIFILM (P 100).
K CUSTOM SET
Save settings for P, S, A, M and all O modes
except R (P 22).
83
Using the Menus: Playback Mode
Using the Playback Menu
Playback Menu Options
the a button to enter play1 Press
back mode.
X PHOTOBOOK ASSIST
Create books from your favorite photos (P 58).
Press MENU/OK to display the play2 back
menu.
the selector up or down to
3 Press
highlight the desired menu item.
Press the selector right to display op4 tions
for the highlighted item.
5
Press the selector up or down to
highlight the desired option.
MENU/OK to select the high6 Press
lighted option.
x ERASE
Delete all or selected pictures (P 55).
j MARK FOR UPLOAD TO
Select pictures for upload to YouTube or Facebook
using MyFinePix Studio (Windows only).
■ Selecting Pictures for Upload
Select YouTube to choose movies for upload
to YouTube, FACEBOOK to choose photos and
movies for upload to Facebook.
1
Press the selector left or right to display pic2 tures
and press MENU/OK to select or deselect.
Press DISP/BACK to exit when all the desired pictures are selected.
1 Notes
• Only movies can be selected for upload to YouTube.
• During playback, selected pictures are indicated by
j YouTube or j FACEBOOK icons.
84
Using the Menus: Playback Mode
■ RESET ALL: Deselecting All Pictures
Choose RESET ALL to deselect all pictures. If the
number of pictures affected is very large, a message will be displayed while the operation is in
progress. Press DISP/BACK to exit before the operation is complete.
I SLIDE SHOW
[MULTIPLE]
View pictures in an automated slide show. Choose
the type of show and press MENU/OK to start.
Press DISP/BACK at any time during the show to
view on-screen help. The show can be ended at
any time by pressing MENU/OK.
■ Uploading Pictures (Windows Only)
Selected pictures can be uploaded using the
YouTube/Facebook Upload option in MyFinePix
Studio.
NORMAL
Select with camera
Upload from computer
Description
Press selector left or right to go back or
skip ahead one frame. Select FADE-IN
FADE-IN
for fade transitions between frames.
As
above, except that camera automatiNORMAL g
cally zooms in on faces selected with InFADE-IN g telligent Face detection.
MULTIPLE
Display several pictures at once.
1 Note
The camera will not turn off automatically while a slide
show is in progress.
Menus
For information on installing MyFinePix Studio
and connecting the camera to a computer, see
“Viewing Pictures on a Computer” (P 72).
Option
85
Using the Menus: Playback Mode
B RED EYE REMOVAL
If the current picture is marked with a g icon to
indicate that it was taken with Intelligent Face Detection, this option can be used to remove redeye. The camera will analyze the image; if red-eye
is detected, the image will be processed to create
a copy with reduced red-eye.
1 Display the desired picture.
Select B RED EYE REMOVAL in the playback
2 menu.
3 Press MENU/OK.
1 Notes
• Red-eye may not be removed if the camera is unable
to detect a face or the face is in profile. Results may
differ depending on the scene. Red-eye can not be
removed from pictures that have already been processed using red-eye removal or pictures created
with other devices.
• The amount of time needed to process the image
varies with the number of faces detected.
• Copies created with B RED EYE REMOVAL are indicated by a e icon during playback.
86
D PROTECT
Protect pictures from accidental deletion.
1 Select D PROTECT in the playback menu.
one of the following options and
2 Highlight
press MENU/OK:
• FRAME: Protect selected pictures. Press the selector left or right to view pictures and press
MENU/OK to select or deselect. Press DISP/BACK
when the operation is complete.
• SET ALL: Protect all pictures.
• RESET ALL: Remove protection from all pictures.
3 Caution
Protected pictures will be deleted when the memory
card or internal memory is formatted (P 93).
Using the Menus: Playback Mode
G CROP
Create a cropped copy of the current picture.
O RESIZE
Create a small copy of the current picture.
1 Display the desired picture.
1 Display the desired picture.
2 Select G CROP in the playback menu.
2 Select O RESIZE in the playback menu.
the k and n buttons to zoom the image 3 Highlight a size and press MENU/OK to display a
3 inUseand
out and use the selector to scroll the
confirmation dialog.
picture until the desired portion is displayed.
4
MENU/OK again to save the cropped copy
5 Press
to a separate file.
Press MENU/OK to display a confirmation dialog.
1 Note
Larger crops produce larger copies; all copies have an
aspect ratio of 4 : 3. If the size of the final copy will be
a, OK will be displayed in yellow.
1 Note
The sizes available vary with the size of the original image.
Menus
b Tip: Intelligent Face Detection
If the picture was shot with Intelligent Face Detection
(P 48), g will be displayed in the monitor. Press the
g button to zoom in on the selected face.
MENU/OK to save the resized copy to a
4 Press
separate file.
87
Using the Menus: Playback Mode
C IMAGE ROTATE
Rotate pictures taken in tall orientation so that
they are displayed in tall orientation in the LCD
monitor.
1
Select C IMAGE ROTATE in the playback
2 menu.
Display the desired picture.
the selector down to rotate the picture
3 Press
90 ° clockwise, up to rotate it 90 ° counterclockwise.
Press MENU/OK. The picture automatically be
4 displayed
in the selected orientation whenever it is played back on the camera.
1 Notes
• Protected pictures can not be rotated. Remove protection before rotating pictures (P 86).
• The camera may not be able to rotate pictures created with other devices.
E COPY
Copy pictures from internal memory to a memory
card.
1 Select E COPY in the playback menu.
one of the following options and
2 Highlight
press the selector right:
• a INTERNAL MEMORY y b CARD: Copy pictures from internal memory to a memory
card.
• b CARD y a INTERNAL MEMORY: Copy pictures from a memory card to internal memory.
one of the following options and
3 Highlight
press MENU/OK:
• FRAME: Copy selected pictures. Press the selector left or right to view pictures and press
MENU/OK to copy the current picture.
• ALL FRAMES: Copy all pictures.
1 Notes
• Copying ends when the destination is full.
• DPOF print information is not copied (P 69).
88
Using the Menus: Playback Mode
F VOICE MEMO
Add a voice memo to the current photograph.
Holding the camera at a distance of about 20 cm,
face the microphone and press MENU/OK to begin
recording. Press MENU/OK again to end recording
(recording ends automatically after 30 seconds).
1 Notes
• Voice memos can not be added to movies or protected pictures. Remove protection from pictures before
recording voice memos.
• If a voice memo already exists for the current picture,
the options will be displayed. Select RE-REC to replace the existing memo.
Playing Voice Memos
Pictures with voice memos are indicated by a q icon
during playback. To play the voice memo back, select
PLAY for F VOICE MEMO in the playback menu.
1 Note
Face recognition links can not be removed from copies
with a size of a or smaller.
K PRINT ORDER (DPOF)
Select pictures for printing on DPOF- and PictBridge-compatible devices (P 67).
Menus
1 Notes
• The camera may not play voice memos recorded
with other devices.
• Do not cover the speaker during playback.
n ERASE FACE RECOG.
Remove face recognition links from the current
image. When this option is selected, the camera
will zoom in on an area in the current picture that
it has matched with a face in the face recognition
database. If the match is not correct, press MENU/
OK to remove the link to the face recognition database.
89
Using the Menus: Playback Mode
J DISP. ASPECT
Choose how High Definition (HD) devices display
pictures with an aspect ratio of 4 : 3 (this option is
available only when an HDMI cable is connected).
Select 16 : 9 to display the image so that it fills the
screen with its top and bottom cropped out, 4 : 3
to display the entire image with black bands at
either side.
16 : 9
4:3
16 : 9
4:3
1 Note
Photographs with an aspect ratio of 16 : 9 are displayed
full screen, those with an aspect ratio of 3 : 2 in a black
frame.
90
The Setup Menu
Using the Setup Menu
the setup menu.
1 Display
1.1 Press MENU/OK to display
the
menu for the current mode.
1.2 Press the selector left to highlight a left tab.
1.3 Press the selector up or down
to select 4.
The setup menu appears.
Adjust settings.
2 2.1
Press the selector right to activate the setup menu.
2.2 Press the selector up or down
to highlight a menu item.
2.3 Press the selector right to display options for the highlighted
item.
SET-UP
SET
2.4 Press the selector up or down
to highlight an option.
SET
EXIT
Tab
2.5 Press MENU/OK to select the
highlighted option.
Menus
2.6 Press DISP/BACK to exit from the
menu.
91
The Setup Menu
Setup Menu Options
Default values are shown in square brackets [ ].
F DATE/TIME
Set the camera clock (P 14).
N TIME DIFFERENCE
[h
[h]
Switch the camera clock instantly from your
home time zone to the local time at your destination when traveling. To specify the difference
between local time and your home time zone:
Highlight g LOCAL and press the selector
1 right.
Use the selector to choose the time difference
2 between
local time and your home time zone
in increments of 15 minutes.
3 Press MENU/OK.
To switch between local time and your home
time zone, highlight g LOCAL or h HOME and
press MENU/OK.
92
Option
h HOME
g LOCAL
Description
Switch to the time currently selected
for F DATE/TIME (see above).
Switch to local time. If this option is
selected, g and the time and date
will be displayed in yellow for three
seconds each time the camera is
turned on.
La
Choose a language (P 14).
o SILENT MODE
[OFF]
Select ON to disable the speaker, flash, and AFassist illuminator in situations in which camera
sounds or lights may be unwelcome (note that
the flash will still fire in C mode).
The Setup Menu
R RESET
Reset all settings except F DATE/TIME, N TIME
DIFFERENCE, O BACKGROUND COLOR, and
Q VIDEO SYSTEM to default values.
Highlight R RESET and press the selector
1 right
to display a confirmation dialog.
2
Highlight OK and press MENU/OK.
K FORMAT
If a memory card is inserted in the camera, this
option will format the memory card. If no memory card is inserted, this option will format internal
memory. Select OK to begin formatting.
Option
3 SEC
1.5 SEC
ZOOM
(CONTINUOUS)
OFF
Description
Pictures are displayed for three seconds (3 SEC) or 1.5 seconds (1.5 SEC).
Colors may differ slightly from those
in the final image.
Pictures are displayed until the MENU/
OK button is pressed.
Pictures are not displayed after shooting.
1 Note
OFF has no effect in continuous shooting mode.
Menus
3 Cautions
• All data—including protected pictures—will be deleted from the memory card or internal memory. Be
sure important files have been copied to a computer
or other storage device.
• Do not open the battery-chamber cover during formatting.
A IMAGE DISP.
[1.5 SEC]
Choose how long pictures are displayed in the
LCD monitor after shooting.
93
The Setup Menu
B FRAME NO.
[CONT.]
New pictures are stored in im- Frame number
age files named using a four100-0001
digit file number assigned
File
by adding one to the last file Directory
number used. The file num- number number
ber is displayed during playback as shown at right. B FRAME NO. controls
whether file numbering is reset to 0001 when a
new memory card is inserted or the current memory card or internal memory is formatted.
Option
CONTINUOUS
RENEW
94
Description
Numbering continues from the last
file number used or the first available file number, whichever is higher.
Choose this option to reduce the
number of pictures with duplicate
file names.
Numbering is reset to 0001 after formatting or when a new memory card
is inserted.
1 Notes
• If the frame number reaches 999-9999, the shutter
release will be disabled (P 111).
• Selecting R RESET (P 93) sets B FRAME NO. to
CONTINUOUS but does not reset the file number.
• Frame numbers for pictures taken with other cameras may differ.
G OPERATION VOL.
[c]
[c
Adjust the volume of the sounds produced when
camera controls are operated. Choose e OFF
(mute) to disable control sounds.
H SHUTTER VOLUME
[c]
[c
Adjust the volume of the sounds produced when
the shutter is released. Choose e OFF (mute) to
disable the shutter sound.
e SHUTTER SOUND
Choose the sound made by the shutter.
[i]
[i
The Setup Menu
I PLAYBACK VOLUME
[7]
Adjust the volume for movie and voice memo
playback.
J LCD BRIGHTNESS
Control the brightness of the display.
[0]
E EVF/LCD MODE
[50 fps]
Choose 30 fps to increase battery life, 50 fps for
improved display quality.
M AUTO POWER OFF
[2 MIN]
Choose the length of time before the camera
turns off automatically when no operations are
performed. Shorter times increase battery life; if
OFF is selected, the camera must be turned off
manually. Note that in some situations the camera turns off automatically even when OFF is selected.
1 QUICK START MODE
[OFF]
Allow the camera to restart in a fast manner after
turned off (24MIN/10 MIN/OFF). After specified
time has passed, the camera will discontinue this
option.
3 Caution
This option will increase drain on the battery.
L DUAL IS MODE
[[l
l]
Choose whether image stabilization is performed
at all times when the camera is in shooting mode
(l CONTINUOUS), or only when the shutter button is pressed halfway (m SHOOTING
ONLY). Choose OFF to turn image stabilization
off when using a tripod.
Menus
95
The Setup Menu
B RED EYE REMOVAL
[ON]
Choose ON to remove red-eye effects caused by
the flash when shooting with Intelligent Face Detection.
1 Notes
• Red-eye reduction is performed only when a face is
detected.
• Red-eye removal is not available with RAW images.
C AF ILLUMINATOR
[ON]
If ON is selected, the AF-assist illuminator will light
to assist autofocus.
3 Cautions
• The camera may be unable to focus using the AF-assist illuminator in some cases. If the camera is unable
to focus in macro mode, try increasing the distance to
the subject.
• Avoid shining the AF-assist illuminator directly into
your subject’s eyes.
96
k AE/AF-LOCK MODE
[P]
If AE&AF ON WHEN PRESSING is selected, exposure and/or focus will lock while the AE/AF LOCK
button is pressed. If AE&AF ON/OFF SWITCH is
selected, exposure and/or focus will lock while the
AE/AF LOCK button is pressed and remain locked
until the button is pressed again (P 32).
v AE/AF-LOCK BUTTON
[AE-L]
Choose whether the AE/AF LOCK button locks only
exposure, only focus, or both exposure and focus
(AE-L / AF-L / AE+AF).
j RAW
[OFF]
Choose RAW+JPEG or RAW to record RAW pictures (note that because RAW data are not processed on the camera, RAW pictures must be copied to a computer for processing). If RAW+JPEG
is selected, JPEG copies will also be recorded.
Choose OFF to record pictures in JPEG format
only.
The Setup Menu
1 Notes
• To convert RAW files for display on a computer, use
the supplied RAW File Converter software.
• Press the RAW button to temporarily change the recording format that has been set (P 18).
3 Cautions
• RAW pictures cannot be recorded to internal memory. Insert a memory card.
• Crop, resize, and red-eye removal options are not
available with RAW images during playback. The
maximum zoom available when viewing RAW images is 3.2×.
j FOCUS CHECK
[ON]
If ON is selected, the image will be magnified in
the display to assist focus when the focus ring is
rotated in manual focus mode (P 41). The camera must be in manual focus mode.
O BACKGROUND COLOR
Choose a color scheme.
c GUIDANCE DISPLAY
Choose whether to display tool tips.
[ON]
Q VIDEO SYSTEM
Choose a video mode for connection to a TV.
Option
NTSC
PAL
Description
Select this mode for connection to
video devices in North America, the
Caribbean, parts of Latin America,
and some East Asian countries.
Select this mode for connection to
video devices in the United Kingdom
and much of Europe, Australia, New
Zealand, and parts of Asia and Africa.
Menus
t SAVE ORG IMAGE
[OFF]
Choose ON to save unprocessed copies of pictures
taken using B RED EYE REMOVAL, j PRO
LOW-LIGHT MODE, or i PRO FOCUS MODE.
m AUTOROTATE PB
[ON]
Choose ON to automatically rotate “tall” (portraitorientation) pictures during playback.
97
The Setup Menu
S CUSTOM RESET
Reset all settings for mode C. A confirmation
dialog will be displayed, press the selector up or
down to highlight OK and press MENU/OK.
T BATTERY TYPE
[x]
[x
Specify the type of battery used in the camera
(P 9).
P DISCHARGE (Ni-MH Batteries Only)
The capacity of rechargeable Ni-MH batteries may
be temporarily reduced when new, after long periods of disuse, or if they are repeatedly recharged
before being fully discharged. Capacity can be
increased by repeatedly discharging the batteries
using the P DISCHARGE option and recharging
them in a battery charger (sold separately). Do
not use P DISCHARGE with non-rechargeable
batteries, and note that the batteries will not discharge if the camera is powered by an optional
AC power adapter and DC coupler.
98
Selecting P DISCHARGE displays a confirma1 tion
dialog. Press MENU/OK.
2 Select OK.
MENU/OK to begin discharging the batter3 Press
ies. When the batteries are fully discharged,
the battery level indicator will blink red and
the camera will turn off. To cancel the process
before the batteries are fully discharged, press
DISP/BACK.
Optional Accessories
The camera supports a wide range of accessories from FUJIFILM and other manufacturers.
■ Remote shutter release
■ Audio/Visual
Standard TV (available from
third-party suppliers)
USB
RR-80 remote release
(sold separately)
A/V cable
FINEPIX HS20EXR
HDTV (available from
third-party suppliers)
■ Computer Related
USB
Computer (available from
third-party suppliers)
HDMI cable
USB
PictBridge-compatible printer
(available from third-party suppliers)
SD card slot or card reader
Technical Notes
SD/SDHC/SDXC
memory card
■ Printing
Printer (available from
third-party suppliers)
99
Optional Accessories
Accessories from FUJIFILM
The following optional accessories are available from FUJIFILM. For the latest information on the accessories available in your region, check with your local FUJIFILM representative or visit http://www.fujifilm.
com/products/digital_cameras/index.html.
AC power adapter AC-5VX (requires
CP-04 DC coupler)
DC coupler
CP-04
Remote release
RR-80
Use to reduce camera shake or keep the shutter open
during a time exposure.
Lens hood
LH-HS10
Use to protect the lens and block light to prevent glare
and lens flare.
Shoe Mount Flash EF-20
Shoe Mount Flash EF-42
100
Use for extended playback or when copying pictures
to a computer (shape of adapter and plug vary with
region of sale).
Connect the AC-5VX AC power adapter to the camera.
Hot-shoe clip-on flash, guide number: 20 (ISO 100),
compatible with i-TTL, bounce capability: up to 90°,
power source: 2 AA-size 1.5V batteries
Hot-shoe clip-on flash, guide number: up to 42 (ISO
100), auto zoom: 24-105mm (equivalent to 135 format),
compatible with i-TTL, bounce capability: up to 90°,
power source: 4 AA-size 1.5V batteries
Set “Format setting” to “35 mm” when using EF-42 and
FINEPIX HS-20EXR.
Caring for the Camera
To ensure continued enjoyment of the product, observe the following precautions.
■ Water and Sand
Exposure to water and sand can also damage the
camera and its internal circuitry and mechanisms.
When using the camera at the beach or seaside,
avoid exposing the camera to water or sand. Do
not place the camera on a wet surface.
■ Condensation
Sudden increases in temperature, such as occur
when entering a heated building on a cold day,
can cause condensation inside the camera. If this
occurs, turn the camera off and wait an hour before turning it on again. If condensation forms on
the memory card, remove the card and wait for
the condensation to dissipate.
Cleaning
Use a blower to remove dust from the lens and
monitor, then gently wipe with a soft, dry cloth.
Any remaining stains can be removed by wiping
gently with a piece of FUJIFILM lens-cleaning paper to which a small amount of lens-cleaning fluid
has been applied. Care should be taken to avoid
scratching the lens or monitor. The camera body
can be cleaned with a soft, dry cloth. Do not use
alcohol, thinner, or other volatile chemicals.
Technical Notes
Storage and Use
If the camera will not be used for an extended period, remove the battery and memory card. Do
not store or use the camera in locations that are:
• exposed to rain, steam, or smoke
• very humid or extremely dusty
• exposed to direct sunlight or very high temperatures, such as in a closed vehicle on a sunny day
• extremely cold
• subject to strong vibration
• exposed to strong magnetic fields, such as near
a broadcasting antenna, power line, radar emitter, motor, transformer, or magnet
• in contact with volatile chemicals such as pesticides
• next to rubber or vinyl products
Traveling
Keep the camera in your carry-on baggage.
Checked baggage may suffer violent shocks that
could damage the camera.
101
Troubleshooting
Power and Battery
Problem
Possible cause
The batteries are exhausted.
The batteries are not in the correct orientation.
The battery-chamber cover is not latched.
The camera does
The AC power adapter and DC coupler are
not turn on.
not connected properly.
The camera has been left for an extended
period with no batteries inserted and the
AC power adapter/DC coupler unplugged.
The batteries are cold.
Power
supply
Troubleshooting
102
There is dirt on the battery terminals.
The camera is in R mode.
The batteries run
down quickly.
The batteries are new, have been left unused
for an extended period, or have been recharged without first being fully discharged
(rechargeable Ni-MH batteries only).
J is selected for focus mode.
The batteries are exhausted.
The camera turns
The AC power adapter or DC coupler has
off suddenly.
been disconnected.
Solution
Page
Insert fresh or fully-charged spare batteries.
8
Re-insert the batteries in the correct orienta8
tion.
Latch the battery-chamber cover.
9
Make sure that the AC power adapter and DC
—
coupler are properly connected.
After inserting the batteries or connecting the
AC power adapter/DC coupler, wait a few mo- —
ments before turning the camera on.
Warm the batteries by placing them in a pocket
or other warm place and re-insert them in the vi
camera immediately before taking a picture.
Clean the terminals with a soft, dry cloth.
—
Select another shooting mode.
21
Discharge Ni-MH batteries using the P DISCHARGE option and recharge them in a battery charger (sold separately). If the batteries
98
do not hold a charge after repeated discharging and recharging, they have reached the end
of their service life and must be replaced.
Select a different focus mode.
41
Insert fresh or fully-charged spare batteries.
8
Make sure that the AC power adapter and DC
—
coupler are properly connected.
Troubleshooting
Menus and Displays
Problem
Possible cause
Solution
Menus and displays are English is not selected for the L a
Select ENGLISH.
not in English.
option in the setup menu.
Page
14, 92
Shooting
Problem
Taking
pictures
EXR AUTO
The monitor
goes dark after
shooting.
The camera
does not
focus.
Pictures are
not the same
size.
Solution
Page
Insert a new memory card or delete pictures. 10, 55
Format the memory card or internal memory. 93
Clean the contacts with a soft, dry cloth.
—
Insert a new memory card.
10
Insert fresh or fully-charged spare batteries.
8
Turn the camera on.
13
The flash has fired.
The monitor may darken while the flash
charges. Wait for the flash to charge.
The subject is close to the camera.
The subject is far away from the camera.
The subject is not suited to autofocus.
34
Select macro mode.
33
Cancel macro mode.
Use focus lock.
31
If S is selected for O IMAGE SIZE in R
mode, the camera will optimize not only senS is selected for O IMAGE SIZE in R sitivity and other settings, but also image size.
21, 78
To record all pictures at the same size, choose
mode.
another shooting mode or select another option for O IMAGE SIZE.
Troubleshooting
Focus
No picture is
taken when
the shutter
button is
pressed.
Possible cause
Memory is full.
Memory is not formatted.
There is dirt on the memory card contacts.
The memory card is damaged.
The batteries are exhausted.
The camera has turned off automatically.
103
Troubleshooting
Problem
Possible cause
Face detection Intelligent Face Detection is not available in
not available. the current shooting mode.
The subject’s face is obscured by sunglasses, a
hat, long hair, or other objects.
The subject’s face occupies only a small area
Intelligent
No face is
of the frame.
Face
detected.
Detection
The subject’s head is tilted or horizontal.
The camera is tilted.
The subject’s face is poorly lit.
Wrong subject The selected subject is closer to the center of
selected.
the frame than the main subject.
Macro mode is Macro mode is not available in the current
Close-ups
not available. shooting mode.
The flash is lowered.
The flash is charging.
The flash is not available in the current shootThe flash does ing mode.
not fire.
The batteries are exhausted.
The camera is in super macro or continuous
shooting mode.
Flash
The camera is in silent mode.
The desired flash mode is not available in the
Flash mode
current shooting mode.
not available.
The camera is in silent mode.
The flash does The subject is not in range of the flash.
not fully light The flash window is obstructed.
the subject.
Fast shutter speed selected.
104
Solution
Choose a different shooting mode.
Page
21
Remove the obstructions.
Change the composition so that the subject’s 48
face occupies a larger area of the frame.
Ask the subject to hold their head straight.
Hold the camera straight.
16
Shoot in bright light.
—
Recompose the picture or turn face detection
41, 48
off and frame the picture using focus lock.
Choose a different shooting mode.
21, 33
Raise the flash.
Wait for the flash to charge.
34
34
Choose a different shooting mode.
21
Insert fresh or fully-charged spare batteries.
8
Turn super macro and continuous shooting
33, 44
modes off.
Turn silent mode off.
18
Choose a different shooting mode.
Turn silent mode off.
Position the subject in range of the flash.
Hold the camera correctly.
Choose a slower shutter speed.
21
18
115
16
29, 30
Troubleshooting
Problem
Pictures are
blurred.
Problem
images
Pictures are
mottled.
Possible cause
The lens is dirty.
The lens is blocked.
s is displayed during shooting and the focus frame is displayed in red.
k is displayed during shooting.
A slow shutter speed is selected at high temperatures.
The camera has been used continuously at
high temperatures or a temperature warning
is displayed.
Pictures are
Recording
Power was interrupted during shooting.
not recorded.
Solution
Clean the lens.
Keep objects away from the lens.
Page
101
16
Check focus before shooting.
109
Use the flash or a tripod.
This is normal and does not indicate a malfunction.
34
—
Turn the camera off and wait for it to cool
down.
—
Turn the camera off before connecting the AC
power adapter/DC coupler. Leaving the camera on can result in corrupted files or damage
to the memory card or internal memory.
—
Troubleshooting
105
Troubleshooting
Playback
Problem
Pictures are
grainy.
Pictures
Playback zoom
unavailable.
No sound in
voice memo
Audio
and movie
playback.
Selected
Deletion pictures not
deleted.
File numberFrame no. ing is unexpectedly reset.
106
Possible cause
The pictures were taken with a different make or
model of camera.
The picture has been saved at a, or is from another make or model of camera.
The camera is in silent mode.
Playback volume is too low.
The microphone was obstructed.
The speaker is obstructed.
Solution
Page
—
—
—
53
Turn silent mode off.
18
Adjust playback volume.
95
Hold the camera correctly during recording. 61, 89
Hold the camera correctly during playback. 63, 89
Some of the pictures selected for deletion are Remove protection using the device with
protected.
which it was originally applied.
86
The battery-chamber cover was opened while Turn the camera off before opening the batthe camera was on.
tery-chamber cover.
13
Troubleshooting
Connections
Solution
Page
View pictures on the TV.
64
Connect the camera correctly.
64
Connect the camera once movie playback
63, 64
has ended.
Set input to “VIDEO”.
—
Match the camera Q VIDEO SYSTEM set97
ting to the TV.
Adjust the volume.
—
Match the camera Q VIDEO SYSTEM set97
ting to the TV.
Connect the camera correctly.
76
Connect the camera correctly.
Turn the printer on.
66
—
—
—
Troubleshooting
Problem
Possible cause
Monitor is off. The camera is connected to a TV.
The camera is not properly connected.
An A/V cable was connected during movie
playback.
No picture or
Input on the television is set to “TV”.
TV
sound.
The camera is not set to the correct video standard.
The volume on the television is too low.
The camera is not set to the correct video stanNo color.
dard.
The computer does not
Computer
The camera is not properly connected.
recognize the
camera.
The camera is not properly connected.
Pictures can
not be printed. The printer is off.
Only one copy
PictBridge
is printed.
The printer is not PictBridge-compatible.
The date is not
printed.
107
Troubleshooting
Miscellaneous
Problem
Possible cause
Nothing happens
Temporary camera malfunction.
when the shutter button is pressed.
The batteries are exhausted.
The camera does not
Temporary camera malfunction.
function as expected.
I want to use an AC
power adapter and DC Check the label on the AC power adapter.
coupler overseas.
No sound.
The camera is in silent mode.
108
Solution
Page
Remove and reinsert the batteries or disconnect and reconnect the AC power adapter/ 8
DC coupler.
Insert fresh or fully-charged spare batteries.
8
Remove and reinsert the batteries or disconnect and reconnect the AC power adapter/
8
DC coupler. If the problem persists, contact
your FUJIFILM dealer.
The AC power adapter can be used with voltages of 100 – 240 V. Consult your travel agent —
for information on plug adapters.
Turn silent mode off.
18
Warning Messages and Displays
The following warnings are displayed in the monitor:
Warning
B (red)
A (blinks red)
k
s
(displayed in red
with red focus
frame)
Aperture or shutter
speed shown in red
FOCUS ERROR
TURN OFF THE CAMERA
AND TURN ON AGAIN
LENS CONTROL ERROR
PROTECTED CARD
Solution
Insert fresh or fully-charged spare batteries.
The camera can not focus.
• Use focus lock to focus on another subject at the
same distance, then recompose the picture (P 31).
• Use macro mode to focus when taking close-ups.
Use the flash or mount the camera on a tripod.
The subject is too bright or too dark. The picIf the subject is dark, use the flash.
ture will be over- or under-exposed.
Camera malfunction.
Turn the camera off and then on again, taking care not
to touch the lens. If the message persists, contact a
FUJIFILM dealer.
The memory card or internal memory is not Format the memory card or internal memory using
formatted or the memory card was formatted the K FORMAT option in the camera setup menu
(P 93).
in a computer or other device.
Clean the contacts with a soft, dry cloth. If the mesThe memory card contacts require cleaning. sage is repeated, format the memory card (P 93). If
the message persists, replace the memory card.
Camera malfunction.
Contact a FUJIFILM dealer.
The memory card is locked.
Unlock the memory card (P 10).
Troubleshooting
CARD NOT INITIALIZED
Description
Batteries are low.
Batteries are exhausted.
Slow shutter speed. Picture may be blurred.
109
Warning Messages and Displays
Warning
BUSY
p
CARD ERROR
a MEMORY FULL
b MEMORY FULL
Description
Solution
The memory card is incorrectly formatted.
Use the camera to format the memory card (P 93).
The camera temperature is too high. If no action is taken, the camera will turn off automati- Turn the camera off and wait for it to cool.
cally.
The memory card is not formatted for use in
Format the memory card (P 93).
the camera.
Clean the contacts with a soft, dry cloth. If the mesThe memory card contacts require cleaning or
sage is repeated, format the memory card (P 93). If
the memory card is damaged.
the message persists, replace the memory card.
Incompatible memory card.
Use a compatible memory card.
Camera malfunction.
Contact a FUJIFILM dealer.
The memory card or internal memory is full Delete pictures or insert a memory card with more free
INTERNAL MEMORY IS FULL and pictures can not be recorded or copied. space.
INSERT A NEW CARD
Re-insert the memory card or turn the camera off
Memory card error or connection error.
and then on again. If the message persists, contact a
FUJIFILM dealer.
WRITE ERROR
Not enough memory remaining to record ad- Delete pictures or insert a memory card with more free
ditional pictures.
space.
The memory card or internal memory is not
Format the memory card or internal memory (P 93).
formatted.
The file is corrupt or was not created with the
The file can not be played back.
camera.
Clean the contacts with a soft, dry cloth. If the mesREAD ERROR
The memory card contacts require cleaning. sage is repeated, format the memory card (P 93). If
the message persists, replace the memory card.
Camera malfunction.
Contact a FUJIFILM dealer.
110
Warning Messages and Displays
Warning
FRAME NO. FULL
TOO MANY FRAMES
PROTECTED FRAME
u ERROR
a CAN NOT CROP
CAN NOT CROP
DPOF FILE ERROR
CAN NOT SET DPOF
F CAN NOT SET DPOF
CAN NOT ROTATE
F CAN NOT ROTATE
NO CARD
Solution
Format the memory card and select RENEW for the
B FRAME NO. option in the X SET-UP menu. Take
The camera has run out of frame numbers (cura picture to reset frame numbering to 100-0001, then
rent frame number is 999-9999).
return to the B FRAME NO. menu and select CONTINUOUS.
A search has returned more than 30,000 reChoose a search that returns fewer results.
sults.
More than 999 images are selected for deleChoose fewer images.
tion.
An attempt was made to add a voice memo to Remove protection before adding voice memos to or
or delete a protected picture.
deleting pictures.
Voice memo file is corrupt.
The voice memo can not be played back.
Camera malfunction.
Contact a FUJIFILM dealer.
An attempt was made to crop a a picture.
The picture selected for cropping is damaged These pictures can not be cropped.
or was not created with the camera.
An attempt was made to create a resized copy
Choose a smaller size.
at a size equal to or larger than the original.
The DPOF print order on the current memory
card contains more than 999 images.
The picture can not be printed using DPOF.
Movies can not be printed using DPOF.
The picture is protected.
Movies can not be rotated.
No memory card inserted when E COPY is
selected.
Copy the pictures to internal memory and create a new
print order.
—
—
Remove protection before rotating pictures.
—
Troubleshooting
P CANNOT EXECUTE
Q CANNOT EXECUTE
a CANNOT EXECUTE
Description
Insert a memory card.
111
Warning Messages and Displays
Warning
b NO IMAGE
a NO IMAGE
PRESS AND HOLD
THE DISP BUTTON TO
DEACTIVATE SILENT MODE
Description
Solution
The source selected for E COPY contains no
Select a different source.
images.
An attempt was made to adjust the volume
Exit silent mode before adjusting the volume.
with the camera in silent mode.
A connection error occurred while pictures
Confirm that the device is turned on and that the USB
COMMUNICATION ERROR were being printed or copied to a computer or
cable is connected.
other device.
Check printer (see printer manual for details). To resume
PRINTER ERROR
Printer out of paper or ink, or other printer er- printing, turn the printer off and then turn it back on.
ror.
PRINTER ERROR
Check printer (see printer manual for details). If printing
RESUME?
does not resume automatically, press MENU/OK to resume.
Movies and some pictures created with other devices
An attempt was made to print a movie, a pic- can not be printed. If the picture was created with the
CAN NOT BE PRINTED ture not created with the camera, or a picture camera, check the printer manual to confirm that the
printer supports the JFIF-JPEG or Exif-JPEG format. If it
in a format not supported by the printer.
does not, the pictures can not be printed.
112
Internal Memory/Memory Card Capacity
The following table shows the recording time or number of pictures available at different image sizes.
All figures are approximate; file size varies with the scene recorded, producing wide variations in the
number of files that can be stored. The number of exposures or length remaining may not diminish at
an even rate. A limited number of test pictures can be taken when no memory card is inserted.
Medium
O
Photographs
Movie
T
O 4:3
O 16:9
P 4:3
P 16:9
Q 4:3
Q 16:9
i 1920 1
h 1280 1
f2
Y 640 × 480 3
Y 320 × 240 3
Y 320 × 112 3
Internal memory
(approx. 20 MB)
FINE
NORMAL
3
5
4
6
4
10
6
13
10
20
19
29
11 sec.
14 sec.
34 sec.
26 sec.
53 sec.
26 sec.
4 GB
FINE
630
840
990
1330
1990
3750
8 GB
NORMAL
1000
1330
1960
2630
3870
5630
38 min.
49 min.
115 min.
86 min.
172 min.
86 min.
FINE
1260
1690
2000
2670
4010
7540
NORMAL
2020
2670
3950
5290
7770
11310
76 min.
99 min.
232 min.
172 min.
345 min.
172 min.
Temperature Warning
The camera will turn off automatically before its temperature or the temperature of the battery rise above safe
limits. Pictures taken when a temperature warning is displayed may exhibit higher levels of “noise” (mottling).
Turn the camera off and wait for it to cool before turning it on again (P 105, 110).
Appendix
1 Use a G card or better. Individual movies can not exceed 29 minutes in length.
2 Individual movies can not exceed 115 minutes in length.
3 Use a G card or better. Individual movies can not exceed 30 seconds in length.
113
Specifications
System
Model
Effective pixels
Image sensor
Storage media
File system
Digital Camera FinePix HS20EXR
16 million
1/
2 -in., EXR CMOS with primary color filter
• Internal memory (approx. 20 MB)
• SD/SDHC/SDXC memory cards
Compliant with Design Rule for Camera File System (DCF), Exif 2.3, and Digital Print Order Format
(DPOF)
File format
• Still pictures: Exif 2.3 JPEG (compressed); RAW (original RAF format, special-purpose software required); RAW+JPEG
available
• Movies: MOV (H.264)
• Audio: WAV
Image size (pixels)
• O 4 : 3: 4,608 × 3,456
• O 3 : 2: 4,608 × 3,072
• O 16 : 9: 4,608 × 2,592
• P 4 : 3: 3,264 × 2,448
• P 3 : 2: 3,264 × 2,176
• P 16 : 9: 3,264 × 1,840
• Q 4 : 3: 2,304 × 1,728
• Q 3 : 2: 2,304 × 1,536
• Q 16 : 9: 1,920 × 1,080
• S MOTION PANORAMA 360: 1,624 × 11,520 (tall)/11,520 × 1,080 (wide)
• S MOTION PANORAMA 180: 1,624 × 5,760 (tall)/5,760 × 1,080 (wide)
• S MOTION PANORAMA 120: 1,624 × 3,840 (tall)/3,840 × 1,080 (wide)
Lens
Fujinon 30 × optical zoom lens, F/2.8 (wide angle)–5.6 (telephoto)
Focal length
f=4.2 mm–126.0 mm (35-mm format equivalent: 24 mm– 720 mm)
Aperture
F2.8–F11 (wide angle)/F5.6–F11 (telephoto) in increments of 1/3 EV; can be set manually or automatically
Focus range (distance from • Approx. 50 cm (1.6 ft.)–infinity (wide angle); 3 m (9.8 ft.)–infinity (telephoto)
front of lens)
• Macro: approx. 10 cm–3 m/0.3 ft.–9.8 ft. (wide angle); 2 m–5 m/6.6 ft.–16.4 ft. (telephoto)
• Super macro: approx. 1 cm–1 m/0.4 in.–3.3 ft.
Sensitivity
Standard output sensitivity equivalent to ISO 100, 200, 400, 800, 1600, 3200, 6400 (image size P or Q),
12800 (image size Q); AUTO, AUTO (400), AUTO (800), AUTO (1600), AUTO (3200)
Metering
256-segment through-the-lens (TTL) metering; MULTI, SPOT, AVERAGE
Exposure control
Programmed AE (with program shift), shutter-priority AE, aperture-priority AE, and manual exposure
Exposure compensation
–2 EV – +2 EV in increments of 1/3 EV (except B, R, M, and U)
114
Specifications
System
Scene modes
Appendix
C (NATURAL & N), D (NATURAL LIGHT), L (PORTRAIT), Z (PORTRAIT ENHANCER), T (DOG),
m (CAT), M (LANDSCAPE), N (SPORT), O (NIGHT), H (NIGHT (TRIPOD)), U (FIREWORKS),
Q (SUNSET), R (SNOW), V (BEACH), U (PARTY), V (FLOWER), W (TEXT)
Picture stabilization
Optical stabilization (image-sensor shift)
Shutter speed (combined • O: 1/4 s–1/4,000 s
• H: 4 s–1/1,000 s
• U: 4 s–1/2 s
mechanical and electronic • P, S, A: 4 s–1/4,000 s
• M: 30 s–1/4,000 s
• Other modes: 1/4 s–1/4,000 s
shutter)
Continuous
• I: max. 32 frames (RAW+JPEG/RAW: max. 6 frames); frame rate can be selected from 11, 8, 5, and 3 fps
• P: 16 or 8 frames; frame rate can be selected from 11, 8, 5, and 3 fps
• O: 3 frames (selected exposure, overexposure, underexposure)
• X: 3 frames (PROVIA, Velvia, ASTIA)
• Y: 3 frames (100%, 200%, 400%)
Focus
• Mode: Single AF, continuous AF, manual focus with one-press AF
• Focus-area selection: Center, multi, area, tracking
• Autofocus system: Contrast-detect TTL AF with AF-assist illuminator
White balance
Automatic scene detection; six manual preset modes for direct sunlight, shade, daylight fluorescent,
warm white fluorescent, cool white fluorescent, and incandescent lighting; custom white balance
Self-timer
Off, 2 sec., 10 sec.; auto shutter release (n and o)
Flash
Manual pop-up flash; effective range when sensitivity is set to AUTO (800) is approx. 30 cm–7.1 m/1 ft.–
23.3 ft. (wide angle), 2.0 m–3.8 m/6.6 ft.–12.5 ft. (telephoto)
Flash modes
Auto, forced flash, off, slow synchro (red-eye removal off); auto with red-eye removal, forced flash
with red-eye removal, off, slow sync with red-eye removal (red-eye removal on)
Electronic viewfinder (EVF) 0.2-in., 200k-dot color LCD viewfinder; frame coverage approx. 97%
Monitor
3.0-in., 460k-dot color LCD monitor; frame coverage approx. 100%
Movies
• i 1920: 1,920 × 1,080 (1080i), 30 fps
• h 1280: 1,280 × 720 (720p), 30 fps
• f: 640 × 480 (VGA), 30 fps
• Y 640 × 480: 640 × 480, 80 fps
• Y 320 × 240: 320 × 240, 160 fps
• Y 320 × 112: 320 × 112, 320 fps
Note: i, h, and f movies are recorded with stereo sound.
115
Specifications
System
Shooting options
Playback options
Other options
Languages
Input/output terminals
A/V OUT (audio/video output)
HDMI output
Digital input/output
116
Dynamic range, Intelligent Face Detection with red-eye removal, framing guideline, frame number
memory, film simulation, histogram display, Pro low-light, Pro focus, motion panorama 360, Electronic level
Intelligent Face Detection, red-eye removal, micro thumbnail, multi-frame playback, image search,
crop, resize, slide show, image rotation, voice memo, histogram display, exposure warning, favorites,
photobook assist
PictBridge, Exif Print, language selection, time difference, silent mode, Eye-Fi Compatible
Arabic, Bulgarian, Simplified Chinese, Traditional Chinese, Czech, Danish, Dutch, English, Farsi, Finnish,
French, German, Greek, Hebrew, Hungarian, Indonesian, Italian, Japanese, Kazakh, Korean, Latvian,
Lithuanian, Norwegian, Polish, Portuguese, Romanian, Russian, Serbian, Slovak, Spanish, Swedish,
Thai, Turkish, Ukrainian, Vietnamese
NTSC or PAL output with monaural sound
HDMI Mini Connector
USB 2.0 High Speed
Specifications
Power supply/other
Power sources
Battery life (approximate
number of frames that can
be taken with fresh or fully
charged batteries)
•
•
•
•
AA alkaline batteries (×4)
AA lithium batteries (×4; available from third-party suppliers)
AA rechargeable nickel-metal hydride (Ni-MH) batteries (×4; available from third-party suppliers)
AC-5VX AC power adapter and CP-04 DC coupler (sold separately)
Battery type
Approximate number of frames
Alkaline (type supplied with camera)
350
Lithium
700
Ni-MH
400
CIPA standard, measured in B (auto) mode using batteries supplied with camera (alkaline batteries
only) and SD memory card.
Camera dimensions
Camera weight
Shooting weight
Operating conditions
Note: Number of shots that can be taken with battery varies with battery charge level and will decline
at low temperatures.
130.6 mm × 90.7 mm × 126.0 mm/5.1 in. × 3.6 in. × 5.0 in. (W × H × D), excluding projections
Approx. 636 g/22.4 oz., excluding batteries, accessories, and memory cards
Approx. 730 g/25.7 oz., including batteries and memory card
• Temperature: 0 °C – +40 °C/+32 °F – +104 °F
• Humidity: 10% – 80% (no condensation)
Appendix
117
Specifications
Color Television Systems
NTSC (National Television System Committee) is a color television telecasting specification adopted mainly in
the U.S.A., Canada, and Japan. PAL (Phase Alternation by Line) is a color television system adopted mainly in
European countries and China.
Notices
• Specifications subject to change without notice; for the latest information, visit http://www.fujifilm.com/products/
digital_cameras/index.html. FUJIFILM shall not be held liable for damages resulting from errors in this manual.
• Although the monitor is manufactured using advanced high-precision technology, small bright points and
anomalous colors (particularly in the vicinity of text) may appear. This is normal for this type of monitor and
does not indicate a malfunction; images recorded with the camera are unaffected.
• Digital cameras may malfunction when exposed to strong radio interference (e.g., electric fields, static electricity, or line noise).
• Due to the type of lens used, some distortion may occur at the periphery of images. This is normal.
118
Memo
119
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN
http://www.fujifilm.com/products/digital_cameras/index.html
Restrictions on Camera Settings
Shooting Mode and Camera Settings
The options available in each shooting mode are listed below.
E
Adv.
R S T U B i j N P
Option
OFF
F
F
G
AUTO
B OFF
N
O
P
N4
K
B ON
L
✔
✔
✔
M
P
S /R
h
✔
✔
o
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔
✔
✔
✔
✔
✔1 ✔ ✔1 ✔1 ✔1
✔
✔
✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
S
A
SP1/SP2
M CD L Z T m M N O H U Q R V U V W F
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔ ✔ ✔ ✔ ✔1
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔
✔
✔
✔ ✔ ✔ ✔1
✔
✔
✔
✔ ✔ ✔
✔1 ✔
✔
✔ ✔ ✔ ✔1
✔
✔
✔
✔ ✔ ✔
✔
✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
n
OFF
I
P
I
O
X
Y
d
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔
✔ ✔ ✔
✔ ✔ ✔
✔
✔
✔
✔
✔1
✔ ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1 ✔
✔
✔
✔ ✔
✔ ✔
✔
✔ ✔
✔ ✔
✔ ✔
✔
✔ ✔
✔ ✔
✔
✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔1 ✔1 ✔1
✔
✔
✔
✔
✔
✔
✔
✔ ✔1 ✔ ✔
✔
✔
✔
✔
✔
✔ ✔ ✔ ✔
✔
✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔1 ✔1 ✔1 ✔1 ✔1 ✔1
✔1 ✔1
✔ ✔ ✔1
✔ ✔ ✔
✔
✔ ✔1 ✔ ✔
✔
✔ ✔
✔
✔
✔ ✔
✔ ✔ ✔ ✔
✔
✔ ✔
✔
✔
✔1 ✔
✔ ✔1
✔
✔
✔ ✔ ✔ ✔
✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔8
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
Restrictions on Camera Settings
E
Adv.
R S T U B i j N P
Option
AUTO
AUTO (3200)
AUTO (1600)
AUTO (800)
AUTO (400)
✔1
✔
✔
✔
✔
✔
✔
✔
✔
6400
3200
1600
400
200
100
o
5
p
q
r
6
s
t
x
J
7
K
j
A
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
SP1/SP2
M CD L Z T m M N O H U Q R V U V W F
✔1 ✔1 ✔1
✔
✔
✔ ✔
✔ ✔
12800
800
S
✔
✔
✔
✔
✔1 ✔
✔
✔
✔1 ✔
✔
✔
✔
✔1 ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1 ✔1 ✔1 ✔1
✔ ✔1 ✔1 ✔1
✔
✔
✔ ✔1 ✔1 ✔1
✔
✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1
✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
Restrictions on Camera Settings
E
Adv.
R S T U B i j N P
Option
O
S
✔
O
✔
✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔1
✔ ✔1
✔1 ✔1 ✔
✔
✔
✔
✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔
✔2 ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
P
Q
T
AUTO
A
B
U
C
D
M
c
d
P
e
b
f
d
f
e
H
h
Z
b
n
F
✔
✔
✔
✔1
✔
✔
✔
✔
✔
✔
✔ ✔1
✔ ✔
✔1 ✔1
SP1/SP2
M CD L Z T m M N O H U Q R V U V W F
S
A
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔8
✔
✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔8
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔8
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔
✔ ✔
✔3
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔2 ✔2 ✔2 ✔3 ✔3 ✔ ✔ ✔3 ✔ ✔ ✔ ✔ ✔3 ✔3 ✔8
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔
✔ ✔ ✔ ✔
✔
Restrictions on Camera Settings
E
Adv.
R S T U B i j N P
Option
S
A
SP1/SP2
M CD L Z T m M N O H U Q R V U V W F
✔
✔
✔
✔
✔
✔
i 1920
h 1280
W
f
Y 640 × 480
Y 320 × 240
Y 320 × 112
I
g
K
l
L
m
✔
✔
OFF
C
j
1
2
3
4
5
6
7
8
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Optimized for selected shooting mode.
ON selected automatically.
OFF selected automatically.
Flash disabled in all shooting modes if lowered.
o (MULTI) selected automatically when Intelligent Face Detection is on.
Camera focuses on faces when Intelligent Face Detection is on.
Intelligent Face Detection turns off automatically in manual focus mode.
Fixed at settings before recording a movie.
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔
✔1
✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔8
✔ ✔ ✔ ✔8
✔ ✔ ✔ ✔8
✔ ✔8
✔ ✔ ✔