BL01256-201
DIGITAL CAMERA
FINEPIX Z85/Z90 Series
Owner’s Manual
Thank you for your purchase
of this product. This manual
describes how to use your
FUJIFILM digital camera and the
supplied software. Be sure that
you have read and understood
its contents and the warnings in
“For Your Safety” (P ii) before using the camera.
For information on related products, visit our website at
http://www.fujifilm.com/products/digital_cameras/index.html
EN
Before You Begin
First Steps
Basic Photography and Playback
More on Photography
More on Playback
Movies
Connections
Menus
Technical Notes
Troubleshooting
Appendix
For Your Safety
IMPORTANT SAFETY INSTRUCTIONS
• Read Instructions: All the safety and operating instructions should be read before the
appliance is operated.
• Retain Instructions: The safety and operating
instructions should be retained for future
reference.
• Heed Warnings: All warnings on the appliance and in the operating instructions
should be adhered to.
• Follow Instructions: All operating and use
instructions should be followed.
Installation
Power Sources: This video product should be
operated only from the type of power source
indicated on the marking label. If you are
not sure of the type of power supply to your
home, consult your appliance dealer or local
power company. For video products intended to operate from battery power, or other
sources, refer to the operating instructions.
Grounding or Polarization: This video product
is equipped with a polarized alternatingcurrent line plug (a plug having one blade
wider than the other). This plug will fit into
the power outlet only one way. This is a safety
feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If
the plug should still fail to fit, contact your
electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
ii
Alternate Warnings: This video product is
equipped with a three-wire grounding-type
plug, a plug having a third (grounding) pin.
This plug will only fit into a grounding-type
power outlet. This is a safety feature. If you
are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose
of the grounding type plug.
Overloading: Do not overload wall outlets and
extension cords as this can result in a risk of
fire or electric shock.
Power-Cord Protection: Power-supply cords
should be routed so that they are not likely
to be walked on or pinched by items placed
upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the point where they exit from
the appliance.
Accessories: Do not place this video product
on an unstable cart, stand, tripod, bracket, or
table. The video product may fall, causing
serious injury to a child or adult, and serious
damage to the appliance. Use only with a
cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with
the video product. Any mounting of the appliance should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
Ventilation: Slots and openings in the cabinet
are provided for ventilation, to ensure reliable
operation of the video product and to protect it from overheating, and these openings
must not be blocked or covered. The openings should never be blocked by placing the
video product on a bed, sofa, rug, or other An appliance and cart
combination should
similar surface.
be moved with care.
This video product should not be placed in a
Quick stops, excesbuilt-in installation such as a bookcase or rack
sive force, and uneven
unless proper ventilation is provided or the
surfaces may cause
manufacturer’s instructions have been adthe appliance and cart
hered to. This video product should never be
combination to overturn.
placed near or over a radiator or heat register.
Attachments: Do not use attachments not
recommended by the video product manufacturer as they may cause hazards.
Water and Moisture: Do not use this video
product near water—for example, near a
bath tub, wash bowl, kitchen sink, or laundry
tub, in a wet basement, or near a swimming
pool, and the like.
For Your Safety
Antennas
Outdoor Antenna Grounding: If an outside
antenna or cable system is connected to the
video product, be sure the antenna or cable
system is grounded so as to provide some
protection against voltage surges and builtup static charges. Section 810 of the National
Electrical Code, ANSI/NFPA No. 70, provides
information with respect to proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
Ground Clamp
Antenna Lead
in Wire
mally follow the operating instructions. Adjust only those controls that are covered by
the operating instructions as an improper
adjustment of other controls may result in
damage and will often require extensive work
by a qualified technician to restore the video
Object and Liquid Entry: Never push objects
product to its normal operation.
of any kind into this video product through
openings as they may touch dangerous volt- When the video product exhibits a distinct
age points or short out parts that could result change in performance—this indicates a
in a fire or electric shock. Never spill liquid of need for service.
any kind on the video product.
Replacement Parts: When replacement parts
Use
Cleaning: Unplug this video product from the
wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
Lightning: For added protection for this video
product receiver during a lightning storm, or
when it is left unattended and unused for
long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable
system. This will prevent damage to the
video product due to lightning and powerline surges.
are required, be sure the service technician
has used replacement parts specified by the
manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or
other hazards.
Safety Check: Upon completion of any service
or repairs to this video product, ask the service technician to perform safety checks to
Service
Antenna
Electric Service
Servicing: Do not attempt to service this video determine that the video product is in proper
Discharge Unit
Equipment
product yourself as opening or removing cov- operating condition.
(NEC SECTION
ers may expose you to dangerous voltage or
810-20)
other hazards. Refer all servicing to qualified
Ground Clamps
Grounding service personnel.
Conductors Damage Requiring Service: Unplug this video
Power Service Grounding
(NEC SECTION product from the wall outlet and refer servicElectrode System (NEC ART
810-21) ing to qualified service personnel under the
250. PART H)
following conditions:
Power Lines: An outside antenna system • When the power-supply cord or plug is
should not be located in the vicinity of overdamaged.
head power lines or other electric light or • If liquid has been spilled, or objects have
power circuits, or where it can fall into such
fallen into the video product.
power lines or circuits. When installing an • If the video product has been exposed to
outside antenna system, extreme care should
rain or water.
be taken to keep from touching such power • If the video product has been dropped or
lines or circuits as contact with them might
the cabinet has been damaged.
be fatal.
If the video product does not operate nor-
iii
For Your Safety
Be sure to read these notes before use
WARNING
Safety Notes
• Make sure that you use your camera correctly. Read these safety
notes and your Owner’s Manual carefully before use.
• After reading these safety notes, store them in a safe place.
About the Icons
The icons shown below are used in this document to indicate the
severity of the injury or damage that can result if the information
indicated by the icon is ignored and the product is used incorrectly
as a result.
WARNING
CAUTION
This icon indicates that death or serious injury can result if the
information is ignored.
This icon indicates that personal injury or material damage can
result if the information is ignored.
The icons shown below are used to indicate the nature of the instructions which are to be observed.
Triangular icons tell you that this information requires attention (“Important”).
Circular icons with a diagonal bar tell you that the action indicated is prohibited (“Prohibited”).
Filled circles with an exclamation mark indicate an action that
must be performed (“Required”).
WARNING
Unplug from
power socket
Avoid exposure
to water
iv
If a problem arises, turn the camera off, remove the battery, and
disconnect and unplug the AC power adapter. Continued use of
the camera when it is emitting smoke, is emitting any unusual
odor, or is in any other abnormal state can cause a fire or electric shock. Contact your FUJIFILM dealer.
Do not allow water or foreign objects to enter the camera. If water
or foreign objects get inside the camera, turn the camera off,
remove the battery, and disconnect and unplug the AC power
adapter. Continued use of the camera can cause a fire or electric shock. Contact your FUJIFILM dealer.
Do not use in
the bathroom or
shower
Do not
disassemble
Do not touch
internal parts
Do not use the camera in the bathroom or shower. This can cause
a fire or electric shock.
Never attempt to change or take apart the camera (never open
the case). Failure to observe this precaution can cause fire or
electric shock.
Should the case break open as the result of a fall or other accident,
do not touch the exposed parts. Failure to observe this precaution could result in electric shock or in injury from touching the
damaged parts. Remove the battery immediately, taking care
to avoid injury or electric shock, and take the product to the
point of purchase for consultation.
Do not change, heat or unduly twist or pull the connection cord and
do not place heavy objects on the connection cord. These actions
could damage the cord and cause a fire or electric shock. If the
cord is damaged, contact your FUJIFILM dealer.
Do not place the camera on an unstable surface. This can cause the
camera to fall or tip over and cause injury.
Never attempt to take pictures while in motion. Do not use the
camera while you are walking or driving a vehicle. This can result in you falling down or being involved in a traffic accident.
Do not touch any metal parts of the camera during a thunderstorm.
This can cause an electric shock due to induced current from
the lightning discharge.
Do not use the battery except as specified. Load the battery as
shown by the indicator.
Do not heat, change or take apart the battery. Do not drop or subject the battery to impacts. Do not store the battery with metallic
products. Any of these actions can cause the battery to burst or
leak and cause fire or injury as a result.
Use only the battery or AC power adapters specified for use with this
camera. Do not use voltages other than the power supply voltage
shown. The use of other power sources can cause a fire.
If the battery leaks and fluid gets in contact with your eyes, skin or
clothing, flush the affected area with clean water and seek medical
attention or call an emergency number right away.
For Your Safety
WARNING
CAUTION
Do not use the charger to charge batteries other than those specified here. The supplied battery charger is for use only with the
type of battery supplied with the camera. Using the charger to
charge conventional batteries or other types of rechargeable
batteries can cause the battery to leak fluid, overheat or burst.
When carrying the battery, install it in a digital camera or keep it in
the hard case. When storing the battery, keep it in the hard case.
When discarding, cover the battery terminals with insulation tape.
Contact with other metallic objects or batteries could cause
the battery to ignite or burst.
Keep memory cards out of the reach of small children. Because
memory cards are small, they can be swallowed by children.
Be sure to store memory cards out of the reach of small children. If a child swallows a memory card, seek medical attention or call an emergency number.
Do not use this camera in locations affected by oil fumes, steam, humidity or dust. This can cause a fire or electric shock.
Do not leave this camera in places subject to extremely high temperatures. Do not leave the camera in locations such as a sealed
vehicle or in direct sunlight. This can cause a fire.
Keep out of the reach of small children. This product could cause
injury in the hands of a child.
Do not place heavy objects on the camera. This can cause the
heavy object to tip over or fall and cause injury.
Do not move the camera while the AC power adapter is still connected. Do not pull on the connection cord to disconnect the AC power
adapter. This can damage the power cord or cables and cause
a fire or electric shock.
Do not use the AC power adapter when the plug is damaged or the
plug socket connection is loose. This could cause a fire or electric
shock.
Do not cover or wrap the camera or the AC power adapter in a cloth
or blanket. This can cause heat to build up and distort the casing or cause a fire.
When you are cleaning the camera or you do not plan to use the
camera for an extended period, remove the battery and disconnect
and unplug the AC power adapter. Failure to do so can cause a
fire or electric shock.
Unplug from
power socket
When charging ends, unplug the charger from the power socket.
Leaving the charger plugged into the power socket can cause
a fire.
Using a flash too close to a person’s eyes may temporarily affect the
eyesight. Take particular care when photographing infants and
young children.
When a memory card is removed, the card could come out of the slot
too quickly. Use your finger to hold it and gently release the card.
Injury could result to those struck by the ejected card.
Request regular internal testing and cleaning for your camera.
Build-up of dust in your camera can cause a fire or electric
shock. Contact your FUJIFILM dealer to request internal cleaning every two years. Please note that this service is not free
of charge.
v
For Your Safety
■ Charging the Battery
Charge the battery in the supplied battery
charger. Charging times will increase at ambient temperatures below +10 °C (+50 °F) or
above +35 °C (+95 °F). Do not attempt to
The following describes the proper use of charge the battery at temperatures above
batteries and how to prolong their life. Incor- 40 °C (+104 °F); at temperatures below 0 °C
rect use can shorten battery life or cause leak- (+32 °F), the battery will not charge.
age, overheating, fire, or explosion.
Do not attempt to recharge a fully charged
Li-ion Batteries
battery. The battery does not however need
Read this section if your camera uses a to be fully discharged before charging.
rechargeable Li-ion battery.
The battery may be warm to the touch immeThe battery is not charged at shipment. diately after charging or use. This is normal.
Charge the battery before use. Keep the bat■ Battery Life
tery in its case when not in use.
At normal temperatures, the battery can be
■ Notes on the Battery
recharged about 300 times. A noticeable deThe battery gradually loses its charge when crease in the length of time the battery will
not in use. Charge the battery one or two hold a charge indicates that it has reached
days before use.
the end of its service life and should be reBattery life can be extended by turning the placed.
The Battery and Power Supply
Note: Check the type of battery used in
your camera and read the appropriate
sections.
camera off when not in use.
Battery capacity decreases at low temperatures; a depleted battery may not function at
when cold. Keep a fully charged spare battery in a warm place and exchange as necessary, or keep the battery in your pocket or
other warm place and insert it in the camera
only when shooting. Do not place the battery in direct contact with hand warmers or
other heating devices.
vi
■ Storage
Performance may be impaired if the battery is
left unused for extended periods when fully
charged. Run the battery flat before storing it.
If the camera will not be used for an extended
period, remove the battery and store it in a
dry place with an ambient temperature of
from +15 °C to +25 °C (+59 °F to +77 °F). Do
not store in locations exposed to extremes of
temperature.
■ Cautions: Handling the Battery
• Do not transport or store with metal objects
such as necklaces or hairpins.
• Do not expose to flame or heat.
• Do not disassemble or modify.
• Use with designated chargers only.
• Do not drop or subject to strong physical
shocks.
• Do not expose to water.
• Keep the terminals clean.
• The battery and camera body may become
warm to the touch after extended use. This
is normal.
AA Alkaline/Rechargeable Ni-MH Batteries
Read this section if your camera uses AA
alkaline or rechargeable AA Ni-MH batteries. Information on compatible battery
types may be found elsewhere in the camera
manual.
■ Cautions: Handling the Batteries
• Do not expose to water, flame, or heat, or
store in warm or humid conditions.
• Do not transport or store with metal objects
such as necklaces or hairpins.
• Do not disassemble or modify the batteries
or battery casing.
• Do not subject to strong physical shocks.
• Do not use batteries that are leaking, deformed, or discolored.
• Keep out of reach of infants and small children.
• Insert in the correct orientation.
For Your Safety
• Do not mix old and new batteries, batteries
with different charge levels, or batteries of
different types.
• If the camera will not be used for an extended period, remove the batteries. Note that
the camera clock will be reset.
• The batteries may be warm to the touch
immediately after use. Turn the camera
off and allow the batteries to cool before
handling.
• Battery capacity tends to decrease at low
temperatures. Keep spare batteries in a
pocket or other warm place and exchange
as necessary. Cold batteries may recover
some of their charge when warmed.
• Fingerprints and other stains on the battery
terminals can impair battery performance.
Thoroughly clean the terminals with a
soft, dry cloth before inserting them in the
camera.
■ Ni-MH Batteries
The capacity of Ni-MH batteries may be
temporarily reduced when new, after long
periods of disuse, or if they are repeatedly
recharged before being fully discharged. This
is normal and does not indicate a malfunction. Capacity can be increased by repeatedly
discharging the batteries using the discharge
option in the camera setup menu and recharging them using a battery charger.
Q CAUTION: Do not use the discharge option
with alkaline batteries.
The camera draws a small amount of current
even when off. Ni-MH batteries that have
been left in the camera for an extended period may be drawn down to the point that
they no longer hold a charge. Battery performance may also drop if the batteries are run
down in a device such as a flashlight. Use the
discharge option in the camera setup menu
If the batteries leak, clean the battery to discharge Ni-MH batteries. Batteries that
compartment thoroughly before in- no longer hold a charge even after repeatserting new batteries.
edly being discharged and recharged have
reached the end of their service life and must
If fluid from the battery comes into
be replaced.
contact with skin or clothing, flush
the affected area with water. If fluid Ni-MH batteries can be recharged in a batenters your eyes, immediately flush the tery charger (sold separately). Batteries may
affected area with water and seek become warm to the touch after charging.
medical attention. Do not rub your eyes. Refer to the instructions provided with the
Failure to observe this precaution could charger for more information. Use the charresult in permanent visual impairment. ger with compatible batteries only.
AC Power Adapters (Available Separately)
This section applies to all camera models.
Use only FUJIFILM AC power adapters designated for use with this camera. Other adapters could damage the camera.
• The AC power adapter is for indoor use only.
• Be sure the DC plug is securely connected
to the camera.
• Turn the camera off before disconnecting
the adapter. Disconnect the adapter by the
plug, not the cable.
• Do not use with other devices.
• Do not disassemble.
• Do not expose to high heat and humidity.
• Do not subject to strong physical shocks.
• The adapter may hum or become hot to the
touch during use. This is normal.
• If the adapter causes radio interference,
reorient or relocate the receiving antenna.
Ni-MH batteries gradually lose their charge
when not in use.
■ Disposal
Dispose of used batteries in accord with local
regulations.
vii
For Your Safety
Using the Camera
Do not aim the camera at extremely bright
light sources, such as the sun in a cloudless
sky. Failure to observe this precaution could
damage the camera image sensor.
Take Test Shots
Before taking photographs on important
occasions (such as at weddings or before
taking the camera on a trip), take a test shot
and view the result in the LCD monitor to ensure that the camera is functioning normally.
FUJIFILM Corporation can not accept liability
for damages or lost profits incurred as a result
of product malfunction.
Notes on Copyright
Unless intended solely for personal use, images recorded using your digital camera system
cannot be used in ways that infringe copyright laws without the consent of the owner.
Note that some restrictions apply to the
photographing of stage performances, entertainments, and exhibits, even when intended
purely for personal use. Users are also asked
to note that the transfer of memory cards
containing images or data protected under
copyright laws is only permissible within the
restrictions imposed by those copyright laws.
Handling
To ensure that images are recorded correctly,
do not subject the camera to impact or physical shocks while images are being recorded.
viii
Liquid Crystal
In the event that the LCD monitor is damaged, care should be taken to avoid contact
with liquid crystal. Take the urgent action
indicated should any of the following situations arise:
• If liquid crystal comes in contact with your
skin, clean the area with a cloth and then
wash thoroughly with soap and running
water.
• If liquid crystal enters your eyes, flush the affected eye with clean water for at least 15
minutes and then seek medical assistance.
• If liquid crystal is swallowed, rinse your
mouth thoroughly with water. Drink large
quantities of water and induce vomiting,
then seek medical assistance.
Electrical Interference
This camera may interfere with hospital or
aviation equipment. Consult with hospital
or airline staff before using the camera in a
hospital or on an aircraft.
Color Television Systems
NTSC (National Television System Committee)
is a color television telecasting specification
adopted mainly in the U.S.A., Canada, and
Japan. PAL (Phases Alternation by Line) is
a color television system adopted mainly in
European countries and China.
Exif Print (Exif Version 2.3)
Exif Print is a newly revised digital camera file
format in which information stored with photographs is used for optimal color reproducAlthough the display is manufactured using tion during printing.
extremely high-precision technology, it may
IMPORTANT NOTICE:
contain pixels that are always lit or that do not
Read Before Using the Software
light. This is not a malfunction, and images reDirect or indirect export, in whole or in part,
corded with the product are unaffected.
of licensed software without the permission
of the applicable governing bodies is proTrademark Information
xD-Picture Card and E are trademarks of hibited.
FUJIFILM Corporation. The typefaces included
herein are solely developed by DynaComware
Taiwan Inc. Macintosh, QuickTime, and Mac
OS are trademarks of Apple Inc. in the U.S.A.
and other countries. Windows 7, Windows
Vista, and the Windows logo are trademarks
of the Microsoft group of companies. Adobe
and Adobe Reader are either trademarks
or registered trademarks of Adobe Systems
Incorporated in the U.S.A. and/or other
countries. The SDHC and SDXC logos are
trademarks of SD-3C, LLC. The HDMI logo is a
trademark. YouTube is a trademark of Google
Inc. All other trade names mentioned in
this manual are the trademarks or registered
trademarks of their respective owners.
About This Manual
Before using the camera, read this manual and the warnings in “For Your Safety” (P ii). For information on specific topics, consult the sources below.
Table of Contents .............................P
.............................P xi
The “Table of Contents” gives an
overview of the entire manual. The
principal camera operations are listed here.
Troubleshooting ............................ P 90
Having a specific problem with the
camera? Find the answer here.
Warning Messages and Displays ..... P 96
Find out what’s behind that flashing
icon or error message in the display.
Memory Cards
Pictures can be stored in the camera’s internal memory or on optional SD, SDHC, and
SDXC memory cards (P 14), referred to in this manual as “memory cards.”
ix
Frequently-Used Buttons
■ Recording Movies
y Press the F button to
shoot a movie. To end
recording, press the F
button again.
■ Taking Pictures During Playback
y To return instantly to shooting mode, press the shutter
button halfway.
Shoot
View
■ Switching Shooting and Playback Modes
Press the a button when shooting
switches to the playback mode.
Press the B button when playback switches to
the shooting mode.
x
Table of Contents
For Your Safety ..................................................................ii
IMPORTANT SAFETY INSTRUCTIONS ..................................ii
Safety Notes ....................................................................iv
About This Manual ...........................................................ix
Frequently-Used Buttons .................................................x
Before You Begin
Symbols and Conventions.................................................1
Supplied Accessories .........................................................1
Parts of the Camera ..........................................................2
Camera Displays (Touch Panel).........................................3
Shooting ........................................................................3
Playback.........................................................................4
The Touch Panel Display....................................................5
Tap.................................................................................5
Scroll..............................................................................5
Rotating the Camera ........................................................6
Shooting ........................................................................6
Playback.........................................................................7
Touch Panel Icons .............................................................8
Shooting ........................................................................8
Playback.........................................................................9
First Steps
Charging the Battery ......................................................10
Inserting the Battery and a Memory Card.....................11
Compatible Memory Cards .............................................14
Turning the Camera on and Off ......................................16
Shooting Mode ..............................................................16
Playback Mode ...............................................................16
Basic Setup ......................................................................18
Basic Photography and Playback
Taking Pictures in Q (Scene Recognition) Mode ......20
Viewing Pictures .............................................................24
More on Photography
Shooting Mode ................................................................25
B AUTO .......................................................................26
J TOUCH & SHOOT ......................................................26
x TOUCH & TRACK ........................................................26
SP SCENE POSITION.......................................................27
r MOTION PANORAMA ...............................................28
D/C NATURAL LIGHT / NATURAL & N ...................30
P PROGRAM AE ..............................................................31
Focus Lock ........................................................................32
d Exposure Compensation ..........................................34
N Using the Flash (Intelligent Flash) ............................35
h Using the Self-Timer .................................................37
F Macro Mode (Close-ups) ...........................................38
b Intelligent Face Detection .......................................39
xi
Table of Contents
xii
More on Playback
Movies
Playback Options.............................................................40
Playback Zoom ...............................................................41
G Multi-Frame Playback .............................................42
e Deleting Pictures ........................................................44
H Image Search............................................................45
K PhotoBook Assist......................................................47
Creating a PhotoBook.....................................................47
Viewing Photobooks ......................................................48
Editing and Deleting Photobooks ...................................48
j Edit ............................................................................49
f COLLAGE .................................................................50
C IMAGE ROTATE .........................................................51
G CROP .......................................................................51
O RESIZE .....................................................................52
B RED EYE REMOVAL...................................................52
L MOVIE TRIMMING....................................................53
P MOVIE JOIN .............................................................54
Viewing Panoramas ........................................................55
Recording Movies ............................................................56
Movie Frame Size ...........................................................57
Viewing Movies ...............................................................58
Connections
Printing Pictures via USB ................................................59
Viewing Pictures on a Computer ....................................61
Windows: Installing MyFinePix Studio ...........................61
Macintosh: Installing FinePixViewer...............................63
Connecting the Camera ..................................................65
Menus
Using the Menus: Shooting Mode ..................................68
Using the Shooting Menu...............................................68
Shooting Menu Options .................................................69
d EXP. COMPENSATION...............................................69
N ISO........................................................................69
O IMAGE SIZE ............................................................70
T IMAGE QUALITY .....................................................71
P FINEPIX COLOR .......................................................71
D WHITE BALANCE ....................................................72
R CONTINUOUS .........................................................72
b FACE DETECTION ....................................................73
V MOVIE QUALITY .....................................................73
c BEST FRAMING ......................................................73
o SILENT MODE.........................................................73
M SET-UP ..................................................................73
Table of Contents
Using the Menus: Playback Mode ..................................74
Using the Playback Menu ...............................................74
Playback Menu Options..................................................74
k PHOTOBOOK ASSIST................................................74
l FAVORITES .............................................................74
h PICTURE COMPARE .................................................74
b IMAGE SEARCH ......................................................75
c EDIT ......................................................................75
I SLIDE SHOW ..........................................................75
D PROTECT................................................................76
E COPY.....................................................................77
A ERASE ...................................................................77
j MARK FOR UPLOAD TO ............................................78
o SILENT MODE.........................................................79
M SET-UP ..................................................................79
The Setup Menu ..............................................................80
Using the Setup Menu....................................................80
Setup Menu Options ......................................................80
A IMAGE DISP. ...........................................................80
B FRAME NO. ............................................................81
L DIGITAL IS..............................................................81
D DIGITAL ZOOM .......................................................82
F DATE/TIME ............................................................82
I VOLUME ................................................................83
b SOUND ..................................................................83
J LCD BRIGHTNESS ....................................................83
K FORMAT ................................................................83
L a ......................................................84
M AUTO POWER OFF ..................................................84
N TIME DIFFERENCE ...................................................84
m AUTOROTATE PB .....................................................85
O BACKGROUND COLOR..............................................85
E LCD MODE .............................................................85
R RESET....................................................................85
h CALIBRATION .........................................................85
i VERSION INFO ........................................................85
xiii
Table of Contents
Technical Notes
Troubleshooting
Optional Accessories .......................................................86
Printing ........................................................................86
Computer Related..........................................................86
Audio/Visual .................................................................86
Accessories from FUJIFILM..............................................87
Caring for the Camera .....................................................88
Storage and Use .............................................................88
Water and Sand.............................................................88
Condensation ................................................................88
Cleaning .........................................................................89
Traveling ........................................................................89
Problems and Solutions ..................................................90
Warning Messages and Displays ....................................96
xiv
Appendix
Tips and Tricks................................................................100
Internal Memory/Memory Card Capacity ....................103
Specifications ................................................................104
Before You Begin
Symbols and Conventions
The following symbols are used in this manual:
Q : This information should be read before use to ensure correct operation.
R : Additional information that may be helpful when using the camera.
P: Other pages in this manual on which related information may be found.
Menus and other text in the LCD monitor are shown in bold. In the illustrations in this manual, displays may be simplified for explanatory purposes.
Supplied Accessories
The following items are included with the camera:
NP-45A rechargeable
battery
• Strap
• User Guide
BC-45B battery charger
USB cable
CD-ROM (contains
this manual)
Attaching the Strap
Attach the strap as shown.
1
Parts of the Camera
For more information, refer to the page listed to the right of each item.
1 Zoom control ...........................................................21, 41
2 Shutter button .............................................................. 22
3 F (movie recording) button ....................................x, 56
4 Flash ............................................................................. 35
5 Microphone .................................................................. 56
6 Lens ............................................................................ 104
7 Speaker......................................................................... 58
8 On/off switch and lens cover......................................... 16
9 Self-timer lamp ............................................................ 37
10 LCD monitor ................................................................ 106
Touch panel display .................................................3, 5, 6
2
11 a (playback) button .............................................24, 40
12 B (shooting) button .............................................16, 24
13 Strap eyelet .................................................................... 1
14 Battery-chamber cover ................................................. 11
15 Tripod mount
16 Connector for USB cable...........................................59, 65
17 Battery chamber ........................................................... 11
18 Memory card slot .......................................................... 12
19 Battery latch ............................................................11, 13
Before You Begin
Parts of the Camera
Camera Displays (Touch Panel)
The following types of indicator may be displayed during shooting and playback. Indicators vary with camera settings.
■ Shooting
1 Battery level ................................................................... 4
2 Intelligent Face Detection indicator .............................. 39
3 Silent mode indicator ................................................... 73
4 White balance............................................................... 72
5 Continuous shooting mode ........................................... 72
6 Focus warning .............................................................. 96
12 / 31 / 2050
7 Blur warning............................................................36, 96
10:00 AM
1600
8 Focus frame .................................................................. 32
127
N DISP
+1 3
MENU
9 FINPIX COLOR ................................................................ 71
10 Internal memory indicator *
11 Image size/quality ........................................................ 70
12 Movie quality................................................................ 73
13 Number of available frames ........................................ 103
14 Sensitivity ..................................................................... 69
15 Date and time ............................................................... 18
16 Exposure compensation ................................................ 34
*a: indicates that no memory card is inserted and that pictures will be stored in the camera’s internal memory (P 12).
P
Before You Begin
3
Parts of the Camera
■ Playback
100-0001
YouTube
MENU
DISP
1 Playback mode indicator..........................................24, 40
2 Intelligent Face Detection indicator .............................. 39
3 Silent mode indicator ................................................... 79
4 Red-eye removal indicator ............................................ 52
5 Edit ............................................................................... 49
6 Photobook assist........................................................... 47
7 Gift image..................................................................... 40
8 Frame number .............................................................. 81
9 Protected image ........................................................... 76
10 Favorites ....................................................................... 74
11 Mark for upload to ........................................................ 78
Battery Level
Battery level is shown as follows:
Indicator
D (white)
C (white)
B (red)
A (blinks red)
Description
Battery partially discharged.
Battery more than half discharged.
Low battery. Charge as soon as possible.
Battery exhausted. Turn camera off and charge battery.
Hiding and Viewing Indicators
Tap DISP to cycle through shooting and playback indicators as follows: all icons and
indicators displayed/all icons and indicators hidden/only button icons displayed.
4
Before You Begin
The Touch Panel Display
The touch panel display can be operated by tapping the display or gliding a
finger over the panel. The panel responds to pressure; use a firm touch, but
do NOT use excessive force.
■ Tap
Lightly tap the display to adjust settings or select pictures or menu options.
P
MENU
DISP
■ Scroll
Glide lightly over the display to scroll
through pictures during playback.
MENU
Before You Begin
Q Note that some monitor covers may
affect the visibility of the image in
the monitor or make the monitor less
responsive. To avoid damaging the
monitor and touch panel display, observe the following precautions:
• Use only your fingers to operate the
panel. Do not use excessive force.
• Do not sit on the camera (by, for example, leaving it in a back pocket
when sitting down), place it under
heavy objects, or attempt to force it
into a small space (such as a suitcase
that is already full).
• Do not attach objects to the camera
strap that might place pressure on
the monitor.
DISP
5
The Touch Panel Display
Rotating the Camera
With some exceptions, the display in the monitor rotates 90 ° when the camera is in “tall” orientation.
■ Shooting
MENU
DISP
MENU
DISP
6
Before You Begin
The Touch Panel Display
■ Playback
MENU
DISP
MENU
DISP
Before You Begin
7
The Touch Panel Display
Touch Panel Icons
■ Shooting
Tap the icons in the shooting display to perform the operations listed below.
The icons displayed vary with the options currently selected.
Shooting mode: Choose a
shooting mode (P 25).
Flash mode: Choose a flash
mode (P 35).
Self-timer: Use the selftimer (P 37).
Shooting menu: View the
shooting menu (P 68).
8
P
MENU
DISP
Macro mode: Shoot in macro mode (P 38).
Display: Turn indicators on
or off (P 4).
Before You Begin
The Touch Panel Display
■ Playback
Tap the icons in the playback display to perform the operations listed below.
The icons displayed vary with the type of picture and the current playback
mode.
Delete: Delete the current
picture (P 44).
Multi-frame: View multiple
pictures (P 42).
Image search: Find pictures
(P 45).
Next: View the next picture (P 24).
Photobook assist: Create
photobooks (P 47).
Previous: View the previous picture (P 24).
Playback menu: View the
playback menu (P 74).
Before You Begin
MENU
DISP
Display: Turn indicators on
or off (P 4).
9
First Steps
Charging the Battery
The battery is not charged at shipment. Charge the battery before use.
1 Place the battery in the supplied battery charger.
Insert the battery in the orientation
indicated by the CBD labels.
Battery
The camera uses an NP-45A rechargeable battery.
CBD
label
Battery charger
2 Plug the charger in.
Arrow
CBD label
Plug the charger into a power outlet. The charging indicator will light.
The Charging Indicator
The charging indicator shows battery charge status as follows:
Charging indicator
Battery status
Off
Battery not inserted.
On (green)
Battery fully charged.
On (yellow)
Battery charging.
Blinks (yellow)
Battery fault.
Action
Insert the battery.
Remove the battery.
—
Unplug the charger and remove the battery.
3 Charge the battery.
Remove the battery when charging is complete.
Q Unplug the charger when it is not in use.
10
Inserting the Battery and a Memory Card
Although the camera can store pictures in internal memory, optional SD,
SDHC and SDXC memory cards (sold separately) can be used to store additional pictures. After charging the battery, insert the battery and memory
card as described below.
1 Open the battery-chamber cover.
R Be sure the camera is off before opening the
battery-chamber cover.
Q Do not open the battery-chamber cover
when the camera is on. Failure to observe this
precaution could result in damage to image
files or memory cards.
Q Do not use excessive force when handling the battery-chamber cover.
2 Insert the battery.
Align the orange stripe on the battery with
the orange battery latch and slide the battery into the camera, keeping the battery
latch pressed to one side.
Q Insert the battery in the correct orientation.
Do NOT use force or attempt to insert the battery upside down or backwards. The battery
will slide in easily in the correct orientation.
First Steps
Orange stripe
Battery latch
11
Inserting the Battery and a Memory Card
3 Insert the memory card.
Holding the memory card in the orientation shown at right, slide it in until it clicks
into place at the back of the slot.
Q Be sure card is in the correct orientation; do
not insert at an angle or use force. If the
Click
memory card is not correctly inserted or no
memory card is inserted, a will appear in
the LCD monitor and internal memory will
be used for recording and playback.
Q SD/SDHC/SDXC memory cards can be locked, making
it impossible to format the card or to record or delete
images. Before inserting an SD/SDHC/SDXC memory
card, slide the write-protect switch to the unlocked Write-protect switch
position.
4 Close the battery-chamber cover.
12
First Steps
Inserting the Battery and a Memory Card
Removing the Battery and Memory Card
Before removing the battery or memory card, turn the camera off and open the
battery-chamber cover.
To remove the battery, press the battery latch to the
side, and slide the battery out of the camera as shown.
Battery latch
To remove the memory card, press it in and release it
slowly. The card can then be removed by hand. When
a memory card is removed, the card could come out
of the slot too quickly. Use your finger to hold it and
gently release the card.
First Steps
13
Inserting the Battery and a Memory Card
■ Compatible Memory Cards
FUJIFILM and SanDisk SD, SDHC and SDXC memory cards have been approved for use in the camera. A complete list of approved memory cards
is available at http://www.fujifilm.com/support/digital_cameras/compatibility/.
Operation is not guaranteed with other cards. The camera can not be used
with xD-Picture Cards or MultiMediaCard (MMC) devices.
Q Memory Cards
• Do not turn the camera off or remove the memory card while the memory card is being formatted
or data are being recorded to or deleted from the card. Failure to observe this precaution
could damage the card.
• Format SD/SDHC/SDXC memory cards before first use, and be sure to reformat all
memory cards after using them in a computer or other device. For more information
on formatting memory cards, see “K FORMAT” (P 83).
• Memory cards are small and can be swallowed; keep out of reach of children. If a
child swallows a memory card, seek medical assistance immediately.
• miniSD or microSD adapters that are larger or smaller than the standard dimensions
of an SD/SDHC/SDXC card may not eject normally; if the card does not eject, take
the camera to an authorized service representative. Do not forcibly remove the card.
• Do not affix labels to memory cards. Peeling labels can cause camera malfunction.
• Movie recording may be interrupted with some types of SD/SDHC/SDXC memory
card. Use a G card or better when shooting HD movies.
14
First Steps
Inserting the Battery and a Memory Card
• The data in internal memory may be erased or corrupted when the camera is repaired. Please note that the repairer will be able to view pictures in internal memory.
• Formatting a memory card or internal memory in the camera creates a folder in
which pictures are stored. Do not rename or delete this folder or use a computer or
other device to edit, delete, or rename image files. Always use the camera to delete
pictures from memory cards and internal memory; before editing or renaming files,
copy them to a computer and edit or rename the copies, not the originals.
Q Batteries
• Remove dirt from the battery terminals with a clean, dry cloth. Failure to observe this
precaution could prevent the battery from charging.
• Do not affix stickers or other objects to the battery. Failure to observe this precaution
could make it impossible to remove the battery from the camera.
• Do not short the battery terminals. The battery could overheat.
• Read the cautions in “The Battery and Power Supply” (P vi).
• Use only battery chargers designated for use with the battery. Failure to observe this
precaution could result in product malfunction.
• Do not remove the labels from the battery or attempt to split or peel the outer casing.
• The battery gradually loses its charge when not in use. Charge the battery one or
two days before use.
First Steps
15
Turning the Camera on and Off
Shooting Mode
To turn the camera on, open the
lens cover fully. The camera turns off
when the lens cover is closed.
Camera on
Camera off
Playback Mode
If the lens cover is closed, the camera
can be turned on in playback mode
by pressing the a button for about
a second.
To turn the camera off, press and
hold the a button.
R Switching to Shooting Mode
To exit to shooting mode, press the shutter button halfway or the B button.
16
First Steps
Turning the Camera on and Off
Q Fingerprints and other marks on the lens can affect pictures. Keep the lens clean.
Q Turning the camera off does not completely end the supply of power to the camera.
R Auto Power Off
The camera will turn off automatically if no operations are performed for the length of
time selected for M AUTO POWER OFF (P 84).
First Steps
17
Basic Setup
A language-selection dialog is displayed the first time the camera is turned
on. Set up the camera as described below (you can reset the clock or change
languages at any time using the F DATE/TIME or L a options in
the setup menu; for information on displaying the setup menu, see page 80).
1 Tap to select a language. Tap 6 or 7 to view additional languages.
START MENU
1/3
R “NO” and “BACK”
Tap BACK to return to the previous step, NO to skip the
current step. Any steps you skip will be displayed the next
time the camera is turned on.
2 The date will be displayed. Tap the 6 or 7 arrows to
set the date and then tap OK. To change the order
in which the year, month, and day are displayed, tap
YY.MM.DD.
3 The time will be displayed. Select AM or PM, tap the
6 or 7 arrows to set the time, and tap OK.
ENGLISH
FRANCAIS
DEUTSCH
ESPAÑOL
PORTUGUÊS
ITALIANO
NEDERLANDS
РУССКИЙ
‫ﻋﺮﺑﻲ‬
START MENU
DATE/TIME
NO
BACK
YY.MM.DD
2010
01
01
YY
MM
DD
START MENU
OK
DATE/TIME
NO
AM
12
00
hh
mm
PM
BACK
18
OK
First Steps
Basic Setup
4 Tap a shooting mode.
5 Tap OK to enter shooting mode when setup is complete.
MENU
DISP
R The Camera Clock
If the battery is removed for an extended period, the camera clock will be reset and the
language-selection dialog will be displayed when the camera is turned on.
First Steps
19
Basic Photography and Playback
Taking Pictures in Q (Scene Recognition) Mode
This section describes how to take pictures in Q (scene
scene recognition)
recognition mode.
The camera automatically analyzes the composition and adjusts settings appropriately.
1 Turn the camera on.
Fully open the lens cover. Q shooting indicators will be displayed.
The g Icon
This icon indicates that the camera continuously searches for faces to select the
appropriate scene, increasing the drain on the battery.
MENU
DISP
The Scene Icon
The camera selects the scene according to shooting conditions and the type of
subject: b PORTRAIT (portraits), c LANDSCAPE (landscapes), d NIGHT (poorly-lit landscapes), e MACRO (close ups), f NIGHT PORTRAIT (poorly-lit portraits), g BACKLIT PORTRAIT
(backlit portraits), a AUTO (all other scenes)
20
Taking Pictures in Q (Scene Recognition) Mode
2 Frame the picture.
Use the zoom control to frame the picture in the display.
MENU
Zoom indicator
DISP
Zoom out
MENU
DISP
Zoom in
Holding the Camera
Hold the camera steady with both hands and brace
your elbows against your sides. Shaking or unsteady
hands can blur your shots.
To prevent pictures that are out of focus or too dark
(underexposed), keep your fingers and other objects
away from the lens and flash.
Basic Photography and Playback
21
Taking Pictures in Q (Scene Recognition) Mode
3 Focus.
Press the shutter button halfway to focus.
R The lens may make a noise when the camera focuses; this
is normal.
Double
beep
If the camera is able to focus, it will beep twice.
If the camera is unable to focus, the focus frame will turn
red, s will be displayed. Change the composition or
use focus lock (P 32).
22
Basic Photography and Playback
Taking Pictures in Q (Scene Recognition) Mode
4 Shoot.
Smoothly press the shutter button the rest of the way
down to take the picture.
Click
R If the subject is poorly lit, the flash may fire when the picture is taken. For information on using the flash when
lighting is poor, see “N Using the Flash (Intelligent Flash)”
(P 35).
The Shutter Button
The shutter button has two positions. Pressing the shutter button halfway sets
focus and exposure; to shoot, press the shutter button the rest of the way down.
Basic Photography and Playback
23
Viewing Pictures
Pictures can be viewed in the LCD monitor. When taking important photographs, take a test shot and check the results.
1 Press the a button.
The most recent picture will be displayed.
2 View additional pictures.
Scroll left or right or tap 8 or 9.
MENU
DISP
MENU
DISP
Press the shutter button or the B button to exit to shooting mode.
24
Basic Photography and Playback
More on Photography
Shooting Mode
Choose a shooting mode according to the scene or type
of subject. Tap the shooting mode icon in the monitor
and tap the icon for the desired mode.
Mode
SCENE RECOGNITION
See
20
AUTO
26
TOUCH & SHOOT
26
TOUCH & TRACK
26
SP SCENE POSITION
27
/
Mode
MOTION PANORAMA
See
28
NATURAL LIGHT/
NATURAL & N
30
PROGRAM AE
31
MENU
DISP
A description of the selected mode will be displayed; tap the description to
continue, or wait for it to clear from the display automatically.
25
Shooting Mode
B AUTO
Choose for crisp, clear snapshots. This mode is recommended in most situations.
HOME
BACK
J TOUCH & SHOOT
Choose this mode to take pictures by touching the display instead of pressing the shutter button. Touch anywhere inside the “touch and shoot” area to focus on the
selected subject and take a picture.
MENU
SHOOTING MODE
Scene Recognition
AUTO
Touch&Shoot
Touch&Track
Scene Position
Motion
Panorama
Natural Light
Natural&Flash
Program AE
HOME
BACK
SHOOTING MODE
Scene Recognition
AUTO
Touch&Shoot
Touch&Track
Scene Position
Motion
Panorama
Natural Light
Natural&Flash
Program AE
AUTO
Touch&Shoot
Touch&Track
Motion
Panorama
Natural Light
Natural&Flash
Program AE
P
DISP
x TOUCH & TRACK
Touch the subject in the display. Focus will track the
subject as it moves through the frame.
HOME
SHOOTING MODE
Scene Recognition
R The camera focuses continuously, increasing the drain on
BACK
the battery, and that the sound of the camera focusing may
be audible.
R Focus will be fixed at the center of the display when macro is on.
Scene Position
26
P
P
More on Photography
Shooting Mode
SP SCENE POSITION
The camera offers a choice of “scenes,” each adapted to
particular shooting conditions or a specific type of subject. Choose from the following options:
HOME
BACK
Scene
L PORTRAIT
Z PORTRAIT ENHANCER
M LANDSCAPE
N SPORT
O NIGHT
H NIGHT (TRIPOD)
Q SUNSET
R SNOW
S BEACH
U PARTY
V FLOWER
W TEXT
More on Photography
SHOOTING MODE
Scene Recognition
AUTO
Touch&Shoot
Touch&Track
Scene Position
Motion
Panorama
Natural Light
Natural&Flash
Program AE
P
Description
Choose for portraits.
Choose for a smooth skin effect when shooting portraits.
Choose for daylight shots of buildings and landscapes.
Choose when photographing moving subjects.
Choose this mode for poorly lit twilight or night scenes.
Choose this mode for slow shutter speeds when shooting at night.
Choose this mode to record the vivid colors in sunrises and sunsets.
Choose for crisp, clear shots that capture the brightness of scenes dominated by shining white snow.
Choose for crisp, clear shots that capture the brightness of sunlit beaches.
Capture indoor background lighting under low-light conditions.
Choose for vivid close-ups of flowers.
Take clear pictures of text or drawings in print.
27
Shooting Mode
r MOTION PANORAMA
Follow an on-screen guide to take photos that will automatically be joined to form a panorama.
HOME
BACK
SHOOTING MODE
Scene Recognition
AUTO
Touch&Shoot
Touch&Track
Scene Position
Motion
Panorama
Natural Light
Natural&Flash
Program AE
1 Tap y and select the pan direction.
1
2 3
3
2 1
P
BACK
2 Take a photograph. Exposure and white balance for the panorama are set
with the first shot.
3 Frame the next shot to overlap with the previous picture by superimposing y on + so that they form a solid circle (z). The camera will release the
shutter automatically.
BACK
1
2 3
Display after 1st shot
28
OK
BACK
1
2 3
OK
Shutter released
More on Photography
Shooting Mode
4 Take the last shot as described in Step 3.
R To end shooting and create a panorama after the first or second shot, tap OK
after completing Step 2 or Step 3 and proceed to Step 5.
5 Tap OK to save the picture.
Q Panoramas are created from multiple frames. The camera may in some cases be
unable to stitch the frames together perfectly.
Q The desired results may not be achieved with moving subjects, subjects close to
the camera, unvarying subjects such as the sky or a field of grass, subjects that are
in constant motion, such as waves and waterfalls, or subjects that undergo marked
changes in brightness. Panoramas may be blurred if the subject is poorly lit.
For Best Results
For best results, be careful not to tilt the camera backward or forward or to either
side and try not to move the camera while y and + are aligned to form a solid circle.
Printing Panoramas
Depending on the page size and the size of the panorama, panoramas may print
with their edges cropped out or with wide margins at the top and bottom or at
both sides.
More on Photography
29
Shooting Mode
D/C NATURAL LIGHT / NATURAL & N
Choose D NATURAL LIGHT or C NATURAL & N.
HOME
BACK
Option
D NATURAL LIGHT
C NATURAL & N
30
SHOOTING MODE
Scene Recognition
AUTO
Touch&Shoot
Touch&Track
Scene Position
Motion
Panorama
Natural Light
Natural&Flash
Program AE
P
Description
Capture natural light indoors, under low light, or where the flash can not be
used. The flash turns off and sensitivity is raised to reduce blur.
This mode helps ensure good results with backlit subjects and in other situations with difficult lighting. Each time the shutter button is pressed, the
camera takes two shots: one shot without the flash to preserve natural lighting, followed immediately by a second shot with the flash. Do not move the
camera until shooting is complete.
More on Photography
Shooting Mode
P PROGRAM AE
The camera sets exposure automatically.
HOME
BACK
More on Photography
SHOOTING MODE
Scene Recognition
AUTO
Touch&Shoot
Touch&Track
Scene Position
Motion
Panorama
Natural Light
Natural&Flash
Program AE
P
31
Focus Lock
To compose photographs with off-center subjects:
1 Focus: Position the subject in the focus frame (U)
and press the shutter button halfway to lock focus and exposure. Focus and exposure will remain
locked while the shutter button is pressed halfway
(AF/AE lock).
MENU
DISP
2 Recompose: Keep the button pressed halfway.
3 Shoot: Press the button all the way down.
32
More on Photography
Focus Lock
Autofocus
Although the camera boasts a high-precision autofocus system, it may be unable to
focus on the subjects listed below. If the camera is unable to focus, focus on another
subject at the same distance and use focus lock to recompose the photograph.
• Very shiny subjects such as mirrors or car bodies.
• Subjects that show little contrast with the background
• Fast-moving subjects.
(for example, subjects in clothing that is the same color
• Subjects photographed through a window or other re- as the background).
• Subjects positioned in front of or behind a high-contrast
flective object.
• Dark subjects and subjects that absorb rather than reflect object that is also in the focus frame (for example, a
light, such as hair or fur.
subject photographed against a backdrop of highly contrasting elements).
• Insubstantial subjects, such as smoke or flame.
More on Photography
33
d Exposure Compensation
To adjust exposure compensation when photographing very bright, very dark, or high-contrast subjects, tap
MENU to display the shooting menu and select d EXP.
COMPENSATION (P 69). Tap e or f to choose an exposure compensation value and then tap OK.
P
MENU
DISP
Choose positive values (6)
to increase exposure
Choose negative values (7)
to reduce exposure
R A d icon and exposure indicator are displayed at settings other than ±0. Exposure
compensation is not reset when the camera is turned off ; to restore normal exposure control, choose a value of ±0.
R Turn the flash off when using exposure compensation.
R Exposure compensation is available only when P (PROGRAM AE) is selected for
shooting mode.
34
More on Photography
N Using the Flash (Intelligent Flash)
When the flash is used, the camera’s Intelligent Flash system instantly analyzes
the scene based on such factors as the brightness of the subject, its position
in the frame, and its distance from the camera. Flash output and sensitivity
are adjusted to ensure that the main subject is correctly exposed while preserving the effects of ambient background lighting, even in dimly-lit indoor
scenes. Use the flash when lighting is poor, for example when shooting at
night or indoors under low light.
Tap the flash icon and choose from the following flash modes:
P
MENU
Option
Q/K
(AUTO FLASH)
FLASH)
N/L
(FORCED FLASH)
FLASH)
P
DISP
MENU
DISP
Description
The flash fires when required. Recommended in most situations.
The flash fires whenever a picture is taken. Use for backlit subjects or for natural
coloration when shooting in bright light.
P
The flash does not fire even when the subject is poorly lit. Use of a tripod is
(SUPPRESSED FLASH
FLASH)) recommended.
O/M
Capture both the main subject and the background under low light (note that
(SLOW SYNCHRO)
SYNCHRO) brightly lit scenes may be overexposed).
More on Photography
35
N Using the Flash (Intelligent Flash)
R If the flash will fire, p will be displayed when the shutter button is pressed halfway.
At slow shutter speeds, k will appear in the display to warn that pictures may be
blurred; use of a tripod is recommended.
R The flash may fire several times with each shot. Do not move the camera until
shooting is complete.
R The flash may cause vignetting.
Red-Eye Removal
When Intelligent Face Detection and red-eye removal (P 39) are on, red-eye removal
is available in auto (K; RED EYE REDUCTION), flash on (L; FORCED FLASH), and
slow sync (M; RED EYE & SLOW) modes. Red-eye removal minimizes “red-eye”
caused when light from the flash is reflected from the subject’s retinas.
36
More on Photography
h Using the Self-Timer
To use the self-timer, tap the self-timer icon and choose from the following
options:
MENU
DISP
MENU
DISP
Option
Description
The camera starts the timer when it detects two portrait subjects close together.
Tap g or h to choose how close the subjects must be together before the timer
a (COUPLE TIME)
starts (the more hearts, the closer the subjects must be together).
R To stop the timer before the picture is taken, press the shutter button halfway.
The camera will start the timer when it detects the selected number of portrait
g (GROUP TIMER) subjects. Tap g or h to choose the number of subjects.
R To stop the timer before the picture is taken, press the shutter button halfway.
The shutter is released ten seconds after the shutter button is pressed. Use for
S (10 SEC)
self-portraits. The self-timer lamp on the front of the camera blinks while the
timer counts down.
The shutter is released two seconds after the shutter button is pressed. Use to
R (2 SEC)
reduce blur caused by the camera moving when the shutter button is pressed.
The self-timer lamp will blink as the timer counts down.
T (OFF)
Self-timer off.
More on Photography
37
F Macro Mode (Close-ups)
For close-ups, tap the macro mode icon and select F. When macro mode is
in effect, the camera focuses on subjects near the center of the frame. Use the
zoom control to compose pictures (P 21).
MENU
DISP
MENU
DISP
To exit macro mode, tap the macro mode icon and select H.
R Use of a tripod is recommended to prevent blur caused by camera shake.
38
More on Photography
b Intelligent Face Detection
Intelligent Face Detection sets focus and exposure for human faces anywhere
in the frame, preventing the camera from focusing on the background in
group portraits. Choose for shots that emphasize portrait subjects.
To use Intelligent Face Detection, tap MENU to display
the shooting menu and select on for b FACE DETECTION (P 73). Faces can be detected with the camera in
vertical or horizontal orientation; if a face is detected,
it will be indicated by a green border. If there is more
than one face in the frame, the camera will select the
face closest to the center; other faces are indicated by
white borders.
MENU
DISP
MENU
DISP
Green border
Q In some modes, the camera may set exposure for the frame
as a whole rather than the portrait subject.
Q If the subject moves as the shutter button is pressed, their face may not be in the
area indicated by the green border when the picture is taken.
More on Photography
39
More on Playback
Playback Options
To view the most recent picture in the LCD monitor, press the a button.
MENU
DISP
Scroll left or right or tap 8 or 9 to view additional pictures.
MENU
DISP
R Pictures taken using other cameras are indicated by a m (“gift image”) icon during
playback.
40
Playback Options
Playback Zoom
To zoom a picture in or out:
1 Display the picture full screen and tap the picture to
display the k icon.
MENU
DISP
k icon
2 Tap the k icon. Zoom controls will be displayed;
tap k to zoom in or n to zoom out (you can also
select i with the camera zoom control to display
the zoom slider and use the zoom control to zoom
in and out, or tap the display to zoom in on the selected area). Tap 6, 7, 8, or 9 to scroll the display.
BACK
DISP
Navigation window shows
portion of image currently
visible in the display
Tap BACK to exit zoom.
R The maximum zoom ratio varies with image size. Playback zoom is not available
with cropped or resized copies saved at a size of a or smaller.
More on Playback
41
Playback Options
G Multi-Frame Playback
To view pictures nine at a time, tap G in single-frame view. The number of
pictures displayed changes each time you tap G (you can also select j with
the camera zoom control to increase the number of pictures displayed or i
to decrease the number of pictures).
MENU
DISP
BACK
1 frame
9 frames
BACK
16 frames
42
More on Playback
Playback Options
In 9- and 16-frame views, scroll left or right or tap 6, 7, 8, or 9 to view more
pictures.
BACK
BACK
Tap a picture to view it full screen.
Rotating the Camera
When the camera is held in “tall” (portrait) orientation, the highlighted
picture appears at the top of the display. Tap 8 or 9 to highlight pictures and tap the picture at the top of the display to view it full screen.
More on Playback
43
e Deleting Pictures
To delete individual pictures, multiple selected pictures,
or all pictures, tap MENU during playback to display the
playback menu, select A ERASE (P 77), and choose
from the options below. Note that deleted pictures can
not be recovered. Copy important pictures to a computer or other storage device before proceeding.
MENU
DISP
Option
Description
Tap g or h to scroll through pictures and tap e. A confirmation dialog will be
displayed; tap OK to delete the current picture. Tap BACK to return to playback
FRAME
when all the desired pictures have been deleted.
Tap pictures to select or deselect (pictures that are protected or in a print order are
SELECTED
shown by S). When the operation is complete, tap OK to display a confirmation
FRAMES
dialog and tap OK to delete the selected pictures.
A confirmation dialog will be displayed; tap OK to delete all unprotected pictures
(if a memory card is inserted, the pictures will be deleted from the memory card;
ALL FRAMES the pictures in internal memory are only deleted if no memory card is inserted).
Tapping BACK cancels deletion; note that any pictures deleted before you tapped
BACK can not be recovered.
R Protected pictures can not be deleted. Remove protection from any pictures you
wish to delete (P 76).
44
More on Playback
H Image Search
Search for pictures.
1 Tap the H icon in single-frame view.
MENU
DISP
2 Choose from the following options:
Option
BY DATE
BY FACE
BY I FAVORITES
BY SCENE
BY TYPE OF DATA
BY UPLOAD MARK
Description
Search by date.
Search for faces from the face recognition database.
Search by rating (P 74).
Search by scene.
Find all still pictures, all movies, or edited pictures.
Find all pictures selected for upload to a specified destination (P 78).
R Searches can also be performed from the playback menu (P 75).
3 Select a search condition. Only pictures that match
the search condition will be displayed (tap j or k
to view additional search conditions).
More on Playback
05/31/2050
BACK
05/31/2050
06/03/2050
08/20/2050
08/22/2050
OK
45
H Image Search
4 The large preview to the left of the thumbnails is the current picture. To
view the current picture full frame, tap the preview or tap OK.
05/31/2050
05/31/2050
DISP
BACK
05/31/2050
06/03/2050
08/20/2050
08/22/2050
OK
OK
BACK
Tap g or h to scroll through the pictures that match the search conditions or tap I to view them in a slide show (P 75). To delete (P 44) or
protect (P 76) the pictures, tap e or D respectively.
5 To exit, tap OK when the current picture is shown full frame. Tap OK to end
the search.
05/31/2050
EXIT SEARCH
DISP
BACK
46
OK
BACK
OK
More on Playback
K PhotoBook Assist
Create books from your favorite photos.
Creating a PhotoBook
1 Tap the K icon in single-frame view.
R Photobook assist can also be accessed from the
playback menu (P 74).
MENU
DISP
2 Tap NEW BOOK.
3 Tap one of the following to choose pictures for the new book.
• SELECT FROM ALL: Choose from all available pictures.
• SELECT BY IMAGE SEARCH: Choose from pictures matching selected search
conditions (P 45).
R Neither photographs a or smaller nor movies can be selected for photobooks.
4 Scroll through the images and tap K to select or deselect the current image for inclusion in the book. To display the current image on the cover,
tap J.
R The first picture selected becomes the cover image. Tap J to select a different
picture for the cover.
5 Tap MENU to exit when the book is complete.
More on Playback
47
K PhotoBook Assist
6 Tap COMPLETE PHOTOBOOK (to select all photos
or all photos matching the specified search conditions for the book, choose SELECT ALL). The new
book will be added to the list in the photobook assist
menu.
HOME
SELECT IMAGES FOR PHOTOBOOK
SELECT ALL
COMPLETE PHOTOBOOK
BACK
Q Books can contain up to 300 pictures.
Q Books that contain no photos are automatically deleted.
Viewing Photobooks
To view a book, tap it in the photobook assist menu and then tap 8 and 9
to scroll through the pictures.
Editing and Deleting Photobooks
Display the photobook and tap MENU. The following options will be displayed; select the desired option and follow the on-screen instructions.
• EDIT: Edit the book as described in “Creating a PhotoBook” (P 47).
• ERASE: Delete the book.
Photobooks
Photobooks can be copied to a computer using the supplied MyFinePix Studio software.
48
More on Playback
j Edit
To edit pictures, tap MENU during playback to display
the playback menu, select j EDIT.
Tap 6 or 7 to scroll through the menu and tap an option to select it.
MENU
DISP
Option
f COLLAGE
C IMAGE ROTATE
G CROP
O RESIZE
B RED EYE REMOVAL
c ASPECT RATIO
c BRIGHTNESS
Description
Create collages (P 50).
Rotate pictures (P 51).
Create cropped copies of pictures (P 51).
Create small copies of pictures (P 52).
Create copies with reduced red eye (P 52).
Choose the aspect ratio.
Adjust brightness.
If the original was taken with Intelligent Face Detection, a mosaic effect
can be applied to up to four faces. If Intelligent Face Detection was off or
c FACE MOSAIC
no faces were detected, the mosaic effect will be applied to the center of
the image.
Remove opening or ending footage to create an edited copy of the current
L MOVIE TRIMMING
movie (P 53).
Add existing footage to the end of the current movie to create an edited
P MOVIE JOIN
copy (P 54).
R Select O RESIZE, c ASPECT RATIO, and c FACE MOZAIC beforehand with other
options; any retouched copied can not be further retouched by those options.
More on Playback
49
j Edit
f COLLAGE
Selecting f COLLAGE displays a selection of collage templates.
1 Tap the desired template for the collage.
2 Tap a frame in the template and then tap a picture at
the right side of the display to place it in the selected
frame (you can also select a picture first and then tap
the target frame). Repeat until the template is filled.
If the desired picture is not visible at the right side of
the display, tap j or k to view more pictures.
COLLAGE
BACK
R To rotate or crop an image for display in a collage, tap
COLLAGE
its frame in the collage template. Rotation and crop
tools will appear at the edges of the display. To rotate
the picture, tap n. The picture is rotated 90 ° clockwise BACK
OK
each time you tap the icon. Tap k or n to zoom the
selected picture in or out and tap 6, 7, 8, or 9 to position it in the frame. Tap
OK when the operation is complete. Note that depending on the template, you
may not be able to rotate or crop the image.
3 Tap OK to complete the collage.
4 Image size options will be displayed. Tap an option to create a collage at
the selected size and save it as a new file.
50
More on Playback
j Edit
C IMAGE ROTATE
This option rotates pictures for display on the camera. It has no effect on pictures displayed on a computer or other device.
1 Tap the left and right arrows (8 and 9) to select the picture you wish to
rotate.
2 Tap W to rotate the picture 90 ° clockwise, X to rotate it 90 ° counterclockwise.
3 Tap OK.
The next time the picture is played back, the rotated one will be displayed.
R The camera may not be able to rotate pictures created with other devices.
G CROP
Create cropped copies of pictures.
1 Tap the left and right arrows (8 and 9) to select the picture you wish to crop.
2 Tap k or n to zoom in and out and tap 6, 7, 8, or 9 to scroll the picture until the desired portion is displayed. Higher zoom ratios produce
smaller copies.
3 Tap OK to save the cropped copy to a separate file.
R Pictures taken with other cameras can not be cropped.
More on Playback
51
j Edit
O RESIZE
Create small copies of pictures.
1 Tap the left and right arrows (8 and 9) to select the picture you wish to resize.
2 Tap an icon to copy the picture at the selected size. The sizes available vary
with the size of the original image.
B RED EYE REMOVAL
This option is used with pictures taken using Intelligent Face Detection to create copies that have been processed to remove red eye.
1 Tap the left and right arrows (8 and 9) to select a picture.
2 Tap OK to create a copy with reduced red-eye.
R Red eye may not be removed if the camera is unable to detect a face or the face is
in profile. Results may differ depending on the scene. Red eye can not be removed
from pictures that have already been processed using red-eye removal.
R The amount of time needed to process the image varies with the number of faces
detected.
R Copies created with B RED EYE REMOVAL are indicated by a e icon during playback.
52
More on Playback
j Edit
L MOVIE TRIMMING
Remove opening or ending footage to create an edited copy of the current
movie.
1 Display the desired movie.
2 Select L MOVIE TRIMMING in the playback menu. To remove footage
from the start of the copy, proceed to Step 3; otherwise, proceed to Step 4.
3 Tap x to begin playback and tap y to pause when the new opening
frame is reached.
4 Tap IN POINT. To remove footage from the end of the copy, proceed to
Step 5; otherwise, proceed to Step 6 (to exit without creating an edited
copy, tap BACK).
5 Tap x to begin playback and tap y to pause when the new closing
frame is reached.
6 Tap OUT POINT to save the copy.
More on Playback
53
j Edit
P MOVIE JOIN
Add existing footage to the end of the current movie to create an edited copy.
1 Display the desired movie.
2 Select P MOVIE JOIN in the playback menu.
3 Tap g or h to highlight a movie.
4 Tap OK to add the highlighted footage to the end of the current movie
and save the resulting copy, or tap BACK to exit without creating a copy.
R Both movies must have been recorded at the same frame size and frame rate and
have a combined file size of no more than 2 GB.
54
More on Playback
Viewing Panoramas
To view a panorama, display in single-frame view and tap
.
100-0001
MENU
DISP
Horizontal panoramas are displayed from left to right. The following operations can be performed during playback:
Operation
Description
End playback Tap z to end playback.
Pause playback Tap y to pause playback. Tap x to resume.
More on Playback
55
Movies
Recording Movies
Press F to shoot a movie. During recording,
y REC and the time remaining will be displayed and sound will be recorded via the built-in
microphone (be careful not to cover the microphone during recording).
y REC icon
999m59s
REC
N
Time remaining
To end recording, press the F button again. Recording ends automatically
when the movie reaches maximum length or memory is full.
R Zoom can be adjusted while recording is in progress.
R Focus is fixed when F is pressed. Exposure and white balance are adjusted automatically throughout recording. The color and brightness of the image may vary
from that displayed before recording begins.
R Sounds made by the camera may be recorded.
56
Recording Movies
Q Do not open the battery chamber during shooting or while a movie is being recorded to a memory. Failure to observe this precaution could prevent the movie
from being played back.
Q Vertical or horizontal streaks may appear in movies containing very bright subjects.
This is normal and does not indicate a malfunction.
Q The temperature of the camera may rise if it is used to record movies for an extended period or if the ambient temperature is high. This is normal and does not
indicate a malfunction.
Movie Frame Size
Before recording, select a frame size using the V MOVIE QUALITY option in
the shooting menu (P 73).
Option
Description
h 1280 (1280 × 720) High Definition.
f (640 × 480)
Standard definition.
Movies
57
Viewing Movies
During playback, movies are displayed as shown at right.
Tap to begin playback. The following operations can
be performed:
Operation
Description
End playback Tap z to end playback.
Pause playback Tap y to pause playback. Tap x to resume.
W mode icon
100-0011
MENU
DISP
Q Do not cover the speaker during playback.
58
Movies
Connections
Printing Pictures via USB
If the printer supports PictBridge, the camera can be connected
directly to the printer as shown below and pictures can be printed
without first being copied to a computer. Note that depending on
the printer, not all the functions described below may be supported.
1 Connect the supplied USB cable as shown and turn the printer on.
2 Press the a button for about a second to turn the camera on.
3 Tap 8 or 9 to select a picture you wish to print.
4 Tap + or – to choose the number of copies (up to 99).
5 Repeat steps 3–4 to select additional pictures. Tap PRINT to display a confirmation dialog when settings are complete.
59
Printing Pictures via USB
6 Tap OK to start printing. Printing can be interrupted by tapping STOP, but
note that some printers may not respond immediately. If the printer stops
before printing is complete, turn the camera off and then on again.
7 After confirming that PRINTING has cleared from the camera display, turn
the camera off and disconnect the USB cable.
R Pictures can be printed from internal memory or a memory card that has been
formatted in the camera.
R If no pictures are selected, the camera will print one copy of the current picture.
R Page size, print quality, and border selections are made using the printer.
Printing the Date of Recording
To print the date of recording on pictures, tap MENU in the PictBridge display and
select PRINT WITH DATE s (to print pictures without the date of recording, select
PRINT WITHOUT DATE).
60
Connections
Viewing Pictures on a Computer
The supplied software can be used to copy pictures to a computer, where
they can be stored, viewed, organized, and printed. Before proceeding, install
the software as described below. Do NOT connect the camera to the computer
until installation is complete.
Windows: Installing MyFinePix Studio
1 Confirm that the computer meets the following system requirements:
Windows 7 *
CPU
RAM
Free disk space
Windows Vista *
3 GHz Pentium 4 or better
Windows XP *
2 GHz Pentium 4 or
better
512 MB or more
2 GB or more
1 GB or more
15 GB or more
• 1024 × 768 pixels or more with 24-bit color or better
Video
• A graphics processing unit (GPU) that supports DirectX 7 or later
• Built-in USB port recommended. Operation is not guaranteed with other
USB ports.
Other
• Internet connection (broadband recommended) required to install
.NET Framework (if necessary), to use auto update feature, and when performing such tasks as sharing pictures on-line or via e-mail.
* Other versions of Windows are not supported. Only pre-installed operating systems are
supported; operation is not guaranteed on home-built computers or computers that have
been upgraded from earlier versions of Windows.
2 Start the computer. Log in to an account with administrator privileges
before proceeding.
Connections
61
Viewing Pictures on a Computer
3 Exit any applications that may be running and insert the installer CD in a
CD-ROM drive.
Windows 7/Windows Vista
If an AutoPlay dialog is displayed, click SETUP.EXE. A “User Account Control”
dialog will then be displayed; click Yes (Windows 7) or Allow (Windows Vista).
The installer will start automatically; click Install MyFinePix Studio and
follow the on-screen instructions to install MyFinePix Studio.
If the Installer Does Not Start Automatically
If the installer does not start automatically, select Computer or My Computer
from the Start menu, then double-click the FINEPIX CD icon to open the FINEPIX
CD window and double-click setup or SETUP.EXE.
4 If prompted to install Windows Media Player, DirectX, or .NET Framework,
follow the on-screen instructions to complete installation.
5 Remove the installer CD from the CD-ROM drive when installation is complete. Store the installer CD in a dry location out of direct sunlight in case
you need to re-install the software.
Installation is now complete. Proceed to “Connecting the Camera” (P 65).
62
Connections
Viewing Pictures on a Computer
Macintosh: Installing FinePixViewer
1 Confirm that the computer meets the following system requirements:
CPU
PowerPC or Intel
Pre-installed copies of Mac OS X version 10.3.9–10.6 (visit http://www.fujifilm.
OS
com/support/digital_cameras/compatibility/ for more information)
RAM
256 MB or more
A minimum of 200 MB required for installation with 400 MB available when
Free disk space
FinePixViewer is running
Video
800 × 600 pixels or more with thousands of colors or better
Built-in USB port recommended. Operation is not guaranteed with other USB
Other
ports.
2 After starting the computer and quitting any applications that may be running, insert the installer CD in a CD-ROM drive and double-click Installer
for Mac OS X.
3 An installer dialog will be displayed; click Installing FinePixViewer to start
installation. Enter an administrator name and password when prompted
and click OK, then follow the on-screen instructions to install FinePixViewer.
Click Exit to quit the installer when installation is complete.
Connections
63
Viewing Pictures on a Computer
4 Remove the installer CD from the CD-ROM drive. Note that you may be
unable to remove the CD if Safari is running; if necessary, quit Safari before
removing the CD. Store the installer CD in a dry location out of direct sunlight in case you need to re-install the software.
5 Mac OS X 10.5 or earlier: Open the “Applications” folder, start Image Capture,
and select Preferences… from the Image Capture application menu. The
Image Capture preferences dialog will be displayed; choose Other… in
the When a camera is connected, open menu, then select FPVBridge in
the “Applications/FinePixViewer” folder and click Open. Quit Image Capture.
Mac OS X 10.6: Connect the camera and turn it on. Open the “Applications”
folder and start Image Capture. The camera will be listed under DEVICES;
select the camera and choose FPVBridge from the Connecting this camera opens menu and click Choose. Quit Image Capture.
Installation is now complete. Proceed to “Connecting the Camera” (P 65).
64
Connections
Viewing Pictures on a Computer
Connecting the Camera
1 If the pictures you wish to copy are stored on a memory card, insert the
card into the camera.
R Windows users may require the Windows CD when starting the software for
the first time.
Q Loss of power during transfer could result in loss of data or damage to internal
memory or the memory card. Charge the battery before connecting the camera.
2 Turn the camera off and connect the supplied USB cable as shown, making sure the
connectors are fully inserted. Connect the
camera directly to the computer; do not use
a USB hub or keyboard.
3 Press the a button for about a second to turn the camera on. MyFinePix
Studio or FinePixViewer will start automatically; follow the on-screen instructions to copy pictures to the computer. To exit without copying pictures, click Cancel.
R If the software does not start automatically, it may not be correctly installed.
Disconnect the camera and reinstall the software.
Connections
65
Viewing Pictures on a Computer
For more information on using the supplied software, start the application
and select the appropriate option from the Help menu.
Q If a memory card containing a large number of images is inserted, there may be a
delay before the software starts and you may be unable to import or save images.
Use a memory card reader to transfer pictures.
Q Make sure that the computer does not display a message stating that copying is in
progress before turning the camera off or disconnecting the USB cable. Failure to
observe this precaution could result in loss of data or damage to internal memory
or the memory card.
Q Disconnect the camera before inserting or removing memory cards.
Q In some cases, it may not be possible to access pictures saved to a network server
using the supplied software in the same way as on a standalone computer.
Q The user bears all applicable fees charged by the phone company or Internet service provider when using services that require an Internet connection.
66
Connections
Viewing Pictures on a Computer
Uninstalling the Supplied Software
Only uninstall the supplied software when it is no longer required or before beginning reinstallation. After quitting the software and disconnecting the camera, drag
the “FinePixViewer” folder from “Applications” into the Trash and select Empty Trash
in the Finder menu (Macintosh), or open the control panel and use “Programs and
Features” (Windows 7/Windows Vista) or “Add or Remove Programs” (Windows XP) to
uninstall MyFinePix Studio. Under Windows, one or more confirmation dialogs may
be displayed; read the contents carefully before clicking OK.
Connections
67
Menus
Using the Menus: Shooting Mode
Use the shooting menu to adjust shooting settings. The options available
vary with the shooting mode selected.
Using the Shooting Menu
1 To view the shooting menu, tap the MENU icon
when the camera is in shooting mode.
P
MENU
2 Tap the icon for the desired menu item.
3 Tap the desired option.
68
DISP
Using the Menus: Shooting Mode
Shooting Menu Options
d EXP. COMPENSATION
Adjust exposure (P 34).
(defaults to 0)
(defaults to AUTO)
N ISO
Control the camera’s sensitivity to light. Higher values can reduce blur; note, however, that mottling may appear in pictures taken at high sensitivities.
100
Bright
Less noticeable
ISO
Scene
Noise (mottling)
3200
Dark
More noticeable
Option
Description
AUTO
Sensitivity is adjusted automatically in response to shooting conditions.
3200 / 1600 / 800 / 400 /
Sensitivity is set to the specified value, which is shown in the display.
200 / 100
Menus
69
Using the Menus: Shooting Mode
O IMAGE SIZE
Choose the image size and aspect ratio at which pictures are recorded.
Large pictures can be printed at large sizes with no drop in quality, while
small pictures require less memory, allowing more pictures to be recorded.
(defaults to O 4:3)
O4:3
Size
Aspect ratio
Size Versus Aspect Ratio
Size
Option
O
P
Q
Prints at sizes up to
34 × 25 cm (13.5 × 10 in.)
24 × 18 cm (9.5 × 7 in.)
17 × 13 cm (7 × 5 in.)
Aspect ratio
4 : 3: Pictures have the same proportions as
16 : 9: Suited for display on High Definition
the camera display.
(HD) devices.
9
3
MENU
DISP
4
70
MENU
DISP
16
Menus
Using the Menus: Shooting Mode
(defaults to NORMAL)
T IMAGE QUALITY
Choose how much image files are compressed.
Option
Description
FINE
Low compression. Select for higher image quality.
NORMAL
High compression. Select this option to store more pictures.
P FINEPIX COLOR
Enhance contrast and color saturation or take pictures in black and white.
Option
cSTANDARD
aCHROME
bB&W
fSEPIA
(defaults to <)
Description
Standard contrast and saturation. Recommended in most situations.
Vivid contrast and color. Choose for vivid shots of flowers or enhanced greens
and blues in landscapes.
Take pictures in black and white.
Take pictures in sepia.
R Settings other than cSTANDARD are shown by an icon in the LCD monitor.
R Depending on the subject, the effects of aCHROME may not be visible in the LCD monitor.
Menus
71
Using the Menus: Shooting Mode
D WHITE BALANCE
For natural colors, choose a setting that matches the light source.
Option
Description
AUTO
White balance adjusted automatically.
For subjects in direct sunlight.
i
For subjects in the shade.
j
Use under “daylight” fluorescent lights.
k
Use under “warm white” fluorescent lights.
l
Use under “cool white” fluorescent lights.
m
Use under incandescent lighting.
n
(defaults to AUTO)
R Results vary with shooting conditions. Play pictures back after shooting to check colors in
the display.
R CONTINUOUS
Capture motion in a series of pictures.
Option
ON
OFF
(defaults to OFF)
Description
The camera takes up to 3 pictures while the shutter button is pressed.
One photograph is taken each time the shutter button is pressed.
R Focus and exposure are determined by the first frame in each series.
R The flash turns off automatically. The previously selected flash mode is restored when OFF is
selected for R CONTINUOUS
CONTINUOUS..
R Frame rate varies with shutter speed.
R The number of pictures that can be recorded depends on the memory available.
72
Menus
Using the Menus: Shooting Mode
b FACE DETECTION
Choose whether the camera automatically detects and sets focus and exposure for human portrait subjects (P 39).
V MOVIE QUALITY
Choose a frame size for movies (P 57).
(defaults to f)
c BEST FRAMING
Choose ON to display a framing guide.
(defaults to OFF)
(defaults to OFF)
o SILENT MODE
Select ON to disable the speaker and flash in situations in which camera sounds or lights may be
unwelcome (note that the flash will still fire in C mode).
M SET-UP
Display the setup menu (P 80).
Menus
73
Using the Menus: Playback Mode
The playback menu is used to manage the pictures in internal memory or on
the memory card.
Using the Playback Menu
1 To view the playback menu, tap the MENU icon during playback.
MENU
DISP
2 Tap the icon for the desired menu item.
3 Tap the desired option.
Playback Menu Options
k PHOTOBOOK ASSIST
Create books from your favorite photos (P 47).
l FAVORITES
To rate the picture currently displayed in full-frame playback, tap I. A ratings dialog will be
displayed; tap to select a rating of from zero to five stars.
h PICTURE COMPARE
Compare two pictures side-by-side. Tap a frame to highlight it and scroll left or right or tap g or
h to choose the picture shown. Tap k to zoom in on the highlighted picture or tap e to delete
it. To exit to single-frame playback, tap BACK.
74
Menus
Using the Menus: Playback Mode
b IMAGE SEARCH
Search for pictures (P 45).
c EDIT
Retouch pictures (P 49).
I SLIDE SHOW
View pictures in an automated slide show. After choosing the background music and display
format, tap a to view the slide show in “wide” (landscape) orientation or U to view the show in
“tall” (portrait) orientation.
Option
NORMAL
FADE-IN
NORMAL g
FADE-IN g
MULTIPLE
SCRAP BOOK VIEW
SELECT BGM
Description
Tap g or h to go back or skip ahead one frame. Select FADE-IN for fade
transitions between frames.
As above, except that camera automatically zooms in on faces selected with
Intelligent Face detection.
Display several pictures at once.
Display multiple pictures in random positions and sizes.
Choose background music.
R The camera will not turn off automatically while a slide show is in progress.
R To exit the slide show, tap the display and tap STOP
STOP..
Menus
75
Using the Menus: Playback Mode
D PROTECT
Protect pictures from accidental deletion.
1 Tap D in the playback menu.
2 Tap one of the following options:
• FRAME: Protect selected pictures. Tap 8 or 9 to select the desired picture. Tap D to protect
the picture. If the picture is already protected, tapping E will remove protection from the
image.
• SET ALL: Protect all pictures.
• RESET ALL: Remove protection from all pictures.
3 Tap BACK to exit when the operation is complete.
Q Protected pictures will be deleted when the memory card or internal memory is formatted
(P 83).
76
Menus
Using the Menus: Playback Mode
E COPY
Copy pictures from internal memory to a memory card.
1 Tap E in the playback menu.
2 Tap one of the following options:
• a INTERNAL MEMORY y b CARD: Copy pictures from internal memory to a memory card.
• b CARD y a INTERNAL MEMORY: Copy pictures from a memory card to internal memory.
3 Select one of the following:
• FRAME: Copy selected pictures. Tap 8 or 9 to view pictures.
• ALL FRAMES: Copy all pictures.
4 Tap OK to copy the current picture.
R Copying ends when the destination is full.
A ERASE
Delete all or selected pictures (P 44).
Menus
77
Using the Menus: Playback Mode
j MARK FOR UPLOAD TO
Select pictures for upload to YouTube or Facebook using MyFinePix Studio (Windows only).
■ Selecting Pictures for Upload
1 Tap j in the playback menu.
2 Tap YouTube to select movies for upload to YouTube, FACEBOOK to select photos and movies for upload to Facebook.
3 Tap 8 or 9 to display pictures and tap OK to select or deselect. Tap BACK to exit when all
the desired pictures are selected.
R Only movies can be selected for upload to YouTube.
R During playback, selected pictures are indicated by j YouTube or j FACEBOOK icons.
■ RESET ALL: Deselecting All Pictures
To deselect all pictures, tap RESET ALL and tap OK, or tap BACK to exit without changing picture status.
If the number of pictures affected is very large, a message will be displayed while the operation
is in progress. Tap BACK to exit before the operation is complete.
■ Uploading Pictures (Windows Only)
Selected pictures can be uploaded using MyFinePix Studio.
For information on installing MyFinePix Studio and connecting the camera to a computer, see
“Viewing Pictures on a Computer” (P 61).
78
Menus
Using the Menus: Playback Mode
(defaults to OFF)
o SILENT MODE
Select ON to disable the speaker and flash in situations in which camera sounds or lights may be
unwelcome (note that the flash will still fire in C mode).
M SET-UP
Display the setup menu (P 80).
Menus
79
The Setup Menu
Using the Setup Menu
1 Tap the MENU icon to display the menu for the current mode.
2 Tap SET (setup).
3 Tap 6 or 7 to display the desired menu item and tap to select.
4 Tap the desired option.
Setup Menu Options
A IMAGE DISP.
Choose how long pictures are displayed in the LCD monitor after shooting.
Option
3 SEC
1.5 SEC
ZOOM (CONTINUOUS)
OFF
(defaults to 1.5 SEC)
Description
Pictures are displayed for three seconds (3 SEC) or 1.5 seconds (1.5 SEC).
Colors may differ slightly from those in the final image.
Pictures are displayed until you tap OK.
Pictures are not displayed after shooting.
R OFF has no effect in continuous shooting mode.
80
Menus
The Setup Menu
(defaults to CONTINUOUS)
B FRAME NO.
New pictures are stored in image files named using a four-digit
Frame number
file number assigned by adding one to the last file number used.
100-0001
The file number is displayed during playback as shown at right.
B FRAME NO. controls whether file numbering is reset to 0001
Directory
File
when a new memory card is inserted or the current memory card
number
number
or internal memory is formatted.
Option
Description
Numbering continues from the last file number used or the first available
CONTINUOUS
file number, whichever is higher. Choose this option to reduce the number of pictures with duplicate file names.
Numbering is reset to 0001 after formatting or when a new memory card
RENEW
is inserted.
R If the frame number reaches 999-9999, the shutter release will be disabled (P
( 98).
R Selecting R RESET (P
( 85) sets B FRAME NO. to CONTINUOUS but does not reset the file
number.
R Frame numbers for pictures taken with other cameras may differ.
(defaults to OFF)
L DIGITAL IS
When AUTO is selected, image stabilization is performed to reduce blur when the subject is
poorly lit.
Menus
81
The Setup Menu
(defaults to OFF)
D DIGITAL ZOOM
If ON is selected, selecting i at the maximum optical zoom position will trigger digital zoom,
further magnifying the image.
The Zoom Indicator
j
i
DIGITAL ZOOM on
Optical zoom
j
Digital zoom
i
DIGITAL ZOOM off
Optical zoom
Q Digital zoom produces lower quality images than optical zoom.
F DATE/TIME
Set the camera clock (P 18).
82
Menus
The Setup Menu
I VOLUME
Adjust volume for the shutter, controls, and playback. Tap an option and choose a volume, either
by selecting an option in a menu (shutter and control volume) or by tapping e and f to choose
a setting between OFF and 10 (playback volume). Tap OK when settings are complete.
b SOUND
Choose the sounds used for the shutter, at startup, and for camera controls. Tap an option and
then tap an icon to choose a sound. Tap OK when settings are complete.
J LCD BRIGHTNESS
Control the brightness of the display.
Option
AUTO
MANUAL
(defaults to AUTO)
Description
Display brightness is automatically adjusted during shooting in response to ambient lighting conditions. Brightness is not adjusted during playback.
Tap 6 or 7 to adjust brightness and then tap OK. Choose from values between
–5 and +5.
K FORMAT
If a memory card is inserted in the camera, this option will format the memory card. If no memory card is inserted, this option will format internal memory. Select OK to begin formatting.
Q All data—including protected pictures—will be deleted from the memory card or internal
memory. Be sure important files have been copied to a computer or other storage device.
Q Do not open the battery cover during formatting.
Menus
83
The Setup Menu
La
Choose a language (P 18).
(defaults to ENGLISH)
(defaults to 2 MIN)
M AUTO POWER OFF
Choose the length of time before the camera turns off automatically when no operations are
performed. Shorter times increase battery life; if OFF is selected, the camera must be turned
off manually. Note that in some situations the camera turns off automatically even when OFF
is selected.
N TIME DIFFERENCE
(defaults to h)
Switch the camera clock instantly from your home time zone to the local time at your destination when traveling. To specify the difference between local time and your home time zone:
1 Tap g LOCAL.
2 Tap the +, –, 6, and 7 icons to choose the time difference. The minimum increment is
15 minutes. Tap OK when settings are complete.
To switch between local time and your home time zone, tap g LOCAL or h HOME.
Option
h HOME
g LOCAL
84
Description
Switch to the time currently selected for F DATE/TIME (P 82).
Switch to local time. If this option is selected, g and the time and date will
be displayed in yellow for three seconds each time the camera is turned on.
Menus
The Setup Menu
(defaults to ON)
m AUTOROTATE PB
Choose ON to automatically rotate “tall” (portrait-orientation) pictures during playback.
O BACKGROUND COLOR
Choose a color scheme.
E LCD MODE
Choose whether the display automatically dims to save power.
(defaults to U ON)
R RESET
Tap OK to reset all settings except F DATE/TIME and N TIME DIFFERENCE to default values.
h CALIBRATION
Calibrate the touch panel. Using your finger, tap the “+” symbols in the order (if you tap too far
from the correct symbol, an error will be displayed; tap the correct symbol again) and tap OK.
i VERSION INFO
Display the current firmware version.
Menus
85
Technical Notes
Optional Accessories
The camera supports a wide range of accessories from FUJIFILM and other
manufacturers.
DIGITAL CAMERA
FINEPIX Z85/Z90
Series
■ Printing
■ Audio/Visual
USB cable
(supplied)
PictBridge-compatible
printer *
Printer *
■ Computer Related
USB cable (supplied)
SD card slot or card reader
Computer *
* Available separately.
86
HDTV *
SD/SDHC/SDXC
memory card
HDMI cable
(sold separately)
HDP-L1
HD player †
† SDXC cards not supported.
Optional Accessories
Accessories from FUJIFILM
The following optional accessories are available from FUJIFILM. For the latest information on the accessories available in your region, check with your
local FUJIFILM representative or visit http://www.fujifilm.com/products/digital_
cameras/index.html.
Rechargeable NP-45A: Additional large-capacity NP-45A rechargeLi-ion batteries able batteries can be purchased as required.
Battery
chargers
HD players
BC-45W: Replacement battery chargers can be purchased as required. The BC-45W charges an NP-45A
battery in about 120 minutes at +20 °C (+68 °F).
HDP-L1 (requires HDMI cable, available from third-party suppliers): Connect to a High Definition (HD) TV to view photographs
and movies from SD/SDHC memory cards.
Technical Notes
87
Caring for the Camera
To ensure continued enjoyment of the product, observe the following precautions.
Storage and Use
If the camera will not be used for an
extended period, remove the battery
and memory card. Do not store or
use the camera in locations that are:
• exposed to rain, steam, or smoke
• very humid or extremely dusty
• exposed to direct sunlight or very
high temperatures, such as in a
closed vehicle on a sunny day
• extremely cold
• subject to strong vibration
• exposed to strong magnetic fields,
such as near a broadcasting antenna, power line, radar emitter, motor,
transformer, or magnet
• in contact with volatile chemicals
such as pesticides
• next to rubber or vinyl products
88
■ Water and Sand
Exposure to water and sand can also
damage the camera and its internal
circuitry and mechanisms. When
using the camera at the beach or
seaside, avoid exposing the camera
to water or sand. Do not place the
camera on a wet surface.
■ Condensation
Sudden increases in temperature,
such as occur when entering a heated
building on a cold day, can cause condensation inside the camera. If this
occurs, turn the camera off and wait
an hour before turning it on again. If
condensation forms on the memory
card, remove the card and wait for the
condensation to dissipate.
Technical Notes
Caring for the Camera
Cleaning
Use a blower to remove dust from the lens and LCD monitor, then gently wipe
with a soft, dry cloth. Any remaining stains can be removed by wiping gently
with a piece of FUJIFILM lens-cleaning paper to which a small amount of lenscleaning fluid has been applied. Care should be taken to avoid scratching the
lens or LCD monitor. The camera body can be cleaned with a soft, dry cloth.
Do not use alcohol, thinner, or other volatile chemicals.
Traveling
Keep the camera in your carry-on baggage. Checked baggage may suffer
violent shocks that could damage the camera.
Technical Notes
89
Troubleshooting
Problems and Solutions
Power and Battery
Problem
The camera does not
turn on.
The battery runs down
quickly.
Solution
• The battery is exhausted
exhausted:: Charge the battery (P
(P 10) or insert a fully-charged spare battery
(P 11).
• The battery is inserted incorrectly:
incorrectly: Reinsert in the correct orientation (P
(P 11).
• The battery-chamber cover is not latched
latched:: Latch the battery-chamber cover (P
(P 12).
• The battery is cold
cold:: Warm the battery by placing it in a pocket or other warm place and reinsert
it in the camera immediately before taking a picture.
• There is dirt on the battery terminals
terminals:: Clean the terminals with a soft, dry cloth.
is selected for shooting mode:
mode: Select
mode to reduce the drain on the battery
•
(P 25).
• The battery has been charged many times
times:: The battery has reached the end of its charging
life. Purchase a new battery.
The camera turns off
Charge the battery (P
(P 10) or insert a fully-charged spare battery ((P
P 11).
suddenly.
Charging does not start. Reinsert the battery in the correct orientation and make sure that the charger is plugged in ((P
P 10).
Charging is slow.
Charge the battery at room temperature (P
(P vi).
• There is dirt on the battery terminals
terminals:: Clean the terminals with a soft, dry cloth.
The charging lamp lights,
• The battery has been charged many times
times:: The battery has reached the end of its charging
but the battery does not
life. Purchase a new battery. If the battery still fails to charge, contact your FUJIFILM dealer.
charge.
• The battery is too hot or too cold
cold:: Wait for the battery temperature to stabilize (P
(P 107).
90
Problems and Solutions
Menus and Displays
Problem
Menus and displays are
not in English.
Solution
Select ENGLISH for L a ((P
P 18, 84).
Shooting
Problem
Solution
Memory is full:
full: Insert a new memory card or delete pictures (P
(P 12, 44).
Memory is not formatted:
formatted: Format the memory card or internal memory (P
(P 83).
There is dirt on the memory card contacts
contacts:: Clean the contacts with a soft, dry cloth.
The memory card is damaged
damaged:: Insert a new memory card (P
(P 12).
The battery is exhausted
exhausted:: Charge the battery (P
(P 10) or insert a fully-charged spare battery
(P 11).
• The camera has turned off automatically:
automatically: Turn the camera on (P
(P 16).
•
•
No picture is taken when •
the shutter button is
•
pressed.
•
The LCD monitor goes
dark after shooting.
The LCD monitor may darken while the flash charges. Wait for the flash to charge (P
(P 35).
The camera does not
focus.
• The subject is close to the camera
camera:: Select macro mode (P
(P 38).
• The subject is far away from the camera
camera:: Cancel macro mode (P
(P 38).
• The subject is not suited to autofocus
autofocus:: Use focus lock (P
(P 32).
Macro mode is not
Choose a different shooting mode (P
(P 25).
available
Intelligent Face Detection
Choose a different shooting mode (P
(P 25).
is not available.
Troubleshooting
91
Problems and Solutions
Problem
No face is detected.
Wrong subject is
selected.
The flash does not fire.
Some flash modes are
not available.
The flash does not fully
light the subject.
92
Solution
• The subject’s face is obscured by sunglasses, a hat, long hair, or other objects:
objects: Remove
the obstructions.
• The subject’s face occupies only a small area of the frame
frame:: Change the composition so that
the subject’s face occupies a larger area of the frame ((P
P 32).
• The subject’s head is tilted or horizontal
horizontal:: Ask the subject to hold their head straight.
• The camera is tilted
tilted:: Keep the camera level (P
(P 21).
• The subject’s face is poorly lit
lit:: Shoot in bright light.
The selected subject is closer to the center of the frame than the main subject. Recompose the
picture or turn face detection off and frame the picture using focus lock ((P
P 32).
• The flash is not available in the current shooting mode:
mode: Choose a different shooting mode
(P 25).
• The battery is exhausted
exhausted:: Charge the battery (P
(P 10) or insert a fully-charged spare battery
(P 11).
• The camera is in continuous mode
mode:: Select OFF for R CONTINUOUS ((P
P 72).
• The camera is in silent mode
mode:: Turn silent mode off (P
(P 73).
• The flash is off (P): Choose a different flash mode (P
(P 35).
• The desired flash mode is not available in the current shooting mode
mode:: Choose a different
shooting mode (P
(P 25).
• The camera is in silent mode
mode:: Turn silent mode off (P
(P 73).
• The subject is not in range of the flash
ash:: Position the subject in range of the flash (P
(P 106).
• The flash window is obstructed
obstructed:: Hold the camera correctly ((P
P 21).
Troubleshooting
Problems and Solutions
Problem
Pictures are blurred.
Pictures are mottled.
Solution
• The lens is dirty
dirty:: Clean the lens (P
(P 89).
• The lens is blocked
blocked:: Keep objects away from the lens (P
(P 21).
• s is displayed during shooting and the focus frame is displayed in red:
red: Check focus
before shooting (P
(P 96).
• k is displayed during shooting:
shooting: Use the flash or a tripod (P
(P 36).
This is normal when slow shutter speeds are selected at high temperatures and does not indicate
a malfunction.
The camera has been used continuously at high temperatures. Turn the camera off and wait for it
to cool down.
Vertical purple or white lines may appear after the camera has been used continuously at high
temperatures or when a very bright object is in the frame; this phenomenon is common to all CCD
image sensors and does not indicate a malfunction. These lines are recorded in movies but do not
appear in photographs. Avoid framing bright objects when filming movies.
Vertical lines appear in
pictures.
“Smear” in the form of
vertical purple or white
lines appears in the
display.
Sounds made by the
• Zoom was adjusted during shooting
shooting:: Do not adjust zoom during shooting.
camera are recorded with
• Intelligent Face Detection is on:
on: Turn Intelligent Face Detection off (P
(P 39).
movies.
Troubleshooting
93
Problems and Solutions
Playback
Problem
Solution
Pictures are grainy.
The pictures were taken with a different make or model of camera.
Playback zoom is unavailThe pictures were created using O RESIZE or with a different make or model of camera.
able.
• Playback volume is too low:
low: Adjust playback volume (P
(P 83).
No sound in movie
• The microphone was obstructed
obstructed:: Hold the camera correctly during recording ((P
P 21, 56).
playback.
• The speaker is obstructed
obstructed:: Hold the camera correctly during playback ((P
P 58).
Selected pictures are not Some of the pictures selected for deletion are protected. Remove protection using the device with
deleted.
which it was originally applied (P
(P 76).
File numbering is
The battery-chamber cover was opened while the camera was on. Turn the camera off before
unexpectedly reset.
opening the battery-chamber cover (P
(P 16).
94
Troubleshooting
Problems and Solutions
Connections/Miscellaneous
Problem
The computer does not
recognize the camera.
Pictures can not be
printed.
Only one copy is printed/
the date is not printed.
The camera is unresponsive.
The camera does not
function as expected.
No sound.
The camera does not respond to the touch panel,
or does not perform the
expected action when
the touch panel is used.
Troubleshooting
Solution
Be sure the camera and computer are correctly connected (P
(P 65).
• The camera is not properly connected
connected:: Connect the camera correctly (P
(P 59).
• The printer is off: Turn the printer on.
The printer is not PictBridge compatible.
• Temporary camera malfunction:
malfunction: Remove and reinsert the battery (P
(P 11).
• The battery is exhausted
exhausted:: Charge the battery (P
(P 10) or insert a fully-charged spare battery
(P 11).
Remove and reinsert the battery (P
(P 11). If the problem persists, contact your FUJIFILM dealer.
Turn silent mode off (P
(P 79).
• The touch panel requires calibration
calibration:: Calibrate the touch panel (P
(P 85).
• The hand that is holding the camera is touching the panel
panel:: Adjust your grip so that the
hand that is holding the camera is not touching the panel.
95
Warning Messages and Displays
The following warnings are displayed in the LCD monitor:
Warning
B ((red
red))
A ((blinks
blinks red)
red)
k
Description
Low battery. Charge the battery (P
(P 10) or insert a fully-charged spare battery ((P
P 11).
Battery exhausted. Charge the battery (P
(P 10) or insert a fully-charged spare battery (P
(P 11).
Slow shutter speed. Pictures may be blurred; use the flash or a tripod.
The camera can not focus. Try one of the following solutions:
s
• Use focus lock to focus on another subject at the same distance, then recompose the picture
(displayed in red with red
(P 32).
focus frame)
frame)
• Use macro mode to focus when taking close-ups (P
(P 38).
Aperture or shutter speed The subject is too bright or too dark and the picture will be over- or under-exposed. If the subject
displayed in red
is dark, use the flash (P
(P 35).
Attempted to take photograph with lens cover closed. Open lens cover before taking photoLENS COVER
graphs.
FOCUS ERROR
Camera malfunction. Turn the camera off and then on again. If the message persists, contact
LENS CONTROL ERROR a FUJIFILM dealer.
• The memory card or internal memory is not formatted or the memory card was formatted in a computer or other device:
device: Format the memory card or internal memory using
the K FORMAT option in the camera setup menu (P
(P 83).
CARD NOT INITIALIZED
• The memory card contacts require cleaning
cleaning:: Clean the contacts with a soft, dry cloth. If
the message is repeated, format the card (P
(P 83). If the message persists, replace the card.
• Camera malfunction:
malfunction: Contact a FUJIFILM dealer.
PROTECTED CARD
The memory card is locked. Unlock the card (P
(P 12).
BUSY
The memory card is incorrectly formatted. Use the camera to format the card (P
(P 83).
96
Troubleshooting
Warning Messages and Displays
Warning
CARD ERROR
a MEMORY FULL
b MEMORY FULL
INTERNAL MEMORY IS
FULL
INSERT A NEW CARD
WRITE ERROR
READ ERROR
Troubleshooting
Description
The memory card is not formatted for use in the camera. Format the card (P
(P 83).
The memory card contacts require cleaning or the memory card is damaged. Clean the contacts
with a soft, dry cloth. If the message is repeated, format the card ((P
P 83). If the message persists,
replace the card.
Incompatible memory card. Use a compatible card (P
(P 14).
Camera malfunction. Contact a FUJIFILM dealer.
The memory card or internal memory is full and pictures can not be recorded or copied. Delete
pictures or insert a memory card with more free space.
• Memory card error or connection error
error:: Reinsert the card or turn the camera off and then
on again. If the message persists, contact a FUJIFILM dealer.
• Not enough memory remaining to record additional pictures
pictures:: Delete pictures or insert
a memory card with more free space.
• The memory card or internal memory is not formatted
formatted:: Format the memory card or
internal memory (P
(P 83).
• The file is corrupt or was not created with the camera
camera:: The file can not be viewed.
• The memory card contacts require cleaning
cleaning:: Clean the contacts with a soft, dry cloth. If
the message is repeated, format the card (P
(P 83). If the message persists, replace the card.
• Camera malfunction:
malfunction: Contact a FUJIFILM dealer.
97
Warning Messages and Displays
Warning
Description
The camera has run out of frame numbers (current frame number is 999-9999). Format the
FRAME NO. FULL
memory card and select RENEW for B FRAME NO. Take a picture to reset frame numbering to 100-0001, then select CONTINUOUS for B FRAME NO. ((P
P 81).
An attempt was made to adjust the volume with the camera in silent mode. Exit silent mode
DEACTIVATE SILENT MODE
before adjusting the volume (P
(P 79).
A search has returned more than 5,000 results, or more than 999 frames were selected for deleTOO MANY FRAMES
tion. Perform a different search or select fewer pictures.
An attempt was made to delete or rotate to a protected picture. Remove protection and try
PROTECTED FRAME
again (P
(P 76).
a pictures can not be cropped.
a CAN NOT CROP
CAN NOT CROP
The picture is damaged or was not created with the camera.
P CANNOT EXECUTE
An attempt was made to create a resized copy at a size equal to or larger than the original.
Q CANNOT EXECUTE
Choose a smaller size.
a CANNOT EXECUTE
CAN NOT ROTATE
An attempt was made to rotate a picture that can not be rotated.
F CAN NOT ROTATE Movies can not be rotated.
m CANNOT EXECUTE Red-eye removal can not be applied to the selected picture.
F CANNOT EXECUTE Red-eye removal can not be applied to movies.
NO CARD
No memory card inserted when E COPY is selected. Insert a memory card.
b NO IMAGE
The source selected for E COPY contains no images. Select a different source.
a NO IMAGE
98
Troubleshooting
Warning Messages and Displays
Warning
Description
A connection error occurred while pictures were being printed or copied to a computer or other
COMMUNICATION ERROR
device. Confirm that the device is turned on and that the USB cable is connected.
Printer out of paper or ink, or other printer error. Check printer (see printer manual for details).
PRINTER ERROR
To resume printing, turn the printer off and then turn it back on.
PRINTER ERROR
Printer out of paper or ink, or other printer error. Check printer (see printer manual for details). If
RESUME?
printing does not resume automatically, tap OK to resume.
An attempt was made to print a movie, a picture not created with the camera, or a picture in a
format not supported by the printer. Movies and some pictures created with other devices can
CANNOT BE PRINTED not be printed; if the picture is a still picture created with the camera, check the printer manual
to confirm that the printer supports the JFIF-JPEG or Exif-JPEG format. If it does not, the pictures
can not be printed.
Troubleshooting
99
Appendix
Tips and Tricks
The following tips and tricks will help you get the most from your camera.
Battery Performance
Choose the following settings for improved battery performance:
• B SHOOTING MODE (P 25): AUTO
• b FACE DETECTION (P 73): OFF
• E LCD MODE (P 85): POWER SAVE ON
The Silent Mode
Turning on the silent mode (P 73, 79) disables the speaker and
flash in situations in which camera sounds or lights may be unwelcome.
The Self-timer
• To prevent blur caused by the camera moving when the shutter button is pressed,
use the two-second timer.
• To turn the timer off, tap BACK (S and R), press the shutter button halfway (a and
g).
100
Tips and Tricks
Intelligent Face Detection
When ON is selected for b FACE DETECTION (P 39), you can:
• Zoom in on faces when ZOOM(CONTINUOUS) is selected for A IMShooting
AGE DISP. (P 80).
• Remove red-eye by selecting ON for Face Detection and red-eye removal.
• Zoom in on faces during slide shows (P 75) or by tapping g during playPlayback
back.
• Search for faces using b IMAGE SEARCH (P 45).
• Crop the background from portraits using G CROP (P 51).
Quick Deletion
Tap e to delete a currently viewing photograph in the playback mode.
Appendix
101
Tips and Tricks
Pro Tips
• To photograph the same scene both with and without the
flash, select C NATURAL & N for B SHOOTING MODE
(P 30). Use h PICTURE COMPARE (P 74) to compare the
two shots.
• To photograph subjects that are in motion, select x TOUCH
& TRACK for B SHOOTING MODE (P 26).
• To fine-tune brightness of a photograph, select P PROGRAM
AE (P 31) for B SHOOTING MODE, choose an appropriate
white balance option (P 72), and adjust exposure compensation (P 34).
102
Appendix
Internal Memory/Memory Card Capacity
The following table shows the recording time or number of pictures available
at different image sizes. All figures are approximate; file size varies with the
scene recorded, producing wide variations in the number of files that can be
stored. The number of exposures or length remaining may not diminish at an
even rate. A limited number of test pictures can be taken when no memory
card is inserted.
Medium
2 GB
4 GB
8 GB
T
O 4:3
O 16:9
P 4:3
P 16:9
Q 4:3
Q 16:9
h1280 †
Internal memory
(approx. 38 MB)
FINE
NORMAL
6
10
8
15
12
21
16
30
28
46
40
55
11 sec.
FINE
NORMAL
320
550
410
780
630
1100
820
1540
1420
2350
2070
2830
11 min.
FINE
NORMAL
640
1100
830
1570
1260
2200
1640
3090
2860
4710
4150
5680
24 min.
FINE
NORMAL
1290
2210
1680
3160
2540
4420
3290
6200
5740
9450
8330
11400
48 min.
f
31 sec.
28 min.
58 min.
116 min.
O
Photographs
Movies*
* Individual movie files can not exceed 2 GB in size.
† Use a G card or better when shooting HD movies.
Appendix
103
Specifications
System
Model
Effective pixels
CCD
Storage media
File system
File format
Image size (pixels)
Lens
Focal length
Digital zoom
Aperture
Focus range
(distance from front of lens)
104
Digital Camera FinePix Z85/Z90 Series
14.2 million
/ -in., square-pixel CCD with primary color filter
• Internal memory (approx. 38 MB)
• SD/SDHC/SDXC memory cards
Compliant with Design Rule for Camera File System (DCF)
(DCF),, Exif 2.3
• Still pictures:
pictures: Exif 2.3 JPEG (compressed)
• Movies
Movies:: AVI-format Motion JPEG
• O 4 : 3:
3: 4,320 × 3,240
• O 16 : 9:
9: 4,320 × 2,432
• P 4 : 3:
3: 3,072 × 2,304
• P 16 : 9:
9: 3,072 × 1,728
• Q 4 : 3:
3: 2,048 × 1,536
• Q 16 : 9:
9: 1,920 × 1,080
Fujinon 5 × optical zoom lens, F3.9 (wide angle) – F4.9 (telephoto)
f=5.0 mm–25.0 mm (35-mm format equivalent: 28 mm–140 mm)
• 4 : 3:
3: Approx. 6.8 × (up to 34 × when combined with optical zoom)
• 16 : 9:
9: Approx. 5.1 × (up to 25 × when combined with optical zoom)
F3.9/F6.2 (wide angle), F4.9/F8.0 (telephoto)
(telephoto);; 2 step
Approx. 60 cm (1.9 ft.)–infinity (wide angle);
angle); 1.0 m (3.2 ft.)–infinity (telephoto)
• Macro
Macro:: approx. 9 cm–80 cm/3.5 in.–2.6 ft. (wide angle);
angle); 40 cm–80 cm/1.3 ft.–2.6 ft. (telephoto)
Appendix
Specifications
System
Sensitivity
Metering
Exposure control
Exposure compensation
Image stabilization
Shutter speed
(combined mechanical and
electronic shutter)
Continuous
Focus
White balance
Appendix
Standard output sensitivity equivalent to ISO 100, 200, 400, 800, 1600, 3200; AUTO
256-segment throughhrough-tthehe-llens (TTL)
Programmed AE
–2 EV – +2 EV in increments of / EV
Digital image stabilization
• AUTO mode:
mode: / s – / s
• Other modes:
modes: 4 s – / s
Up to 0.8 fps, max. 3 frames
• Focus-area selection
selection:: AF CENTER, focus areas selected in J TOUCH & SHOOT and
x TOUCH & TRACK modes
• Autofocus system:
system: Contrast-detect TTL AF
Automatic scene detection; six manual preset modes for direct sunlight, shade, daylight fluorescent, warm white fluorescent, cool white fluorescent, and incandescent
105
Specifications
System
Self-timer
Flash
Flash mode
LCD monitor
Movies
Languages
Off, 2 sec., 10 sec., a ((COUPLE
COUPLE TIMER),
TIMER), g ((GROUP
GROUP TIMER)
TIMER)
Auto flash; effective range when sensitivity is set to AUTO is approx. 70 cm–3.1 m/2.2 ft.–
10.1 ft. (wide angle)
angle),, 70 cm–2.7 m/2.2 ft.–8.8 ft. (telephoto)
(telephoto);; effective range in macro mode is
approx. 30 cm–80 cm/0.9 ft.–2.6 ft.
Auto, fill flash, off, slow sync (red-eye removal off );); auto with red-eye removal, fill flash with redeye removal, off, slow sync with red-eye removal (red-eye removal on)
3.0-in., 230k-dot color LCD monitor; frame coverage approx. 96%
Frame size h1280 (1,280 × 720) or f (640 × 480); 30 fps; monaural sound
Arabic, Bulgarian, Simplified Chinese, Traditional Chinese, Czech, Danish, Dutch, English, Farsi,
Finnish, French, German, Greek, Hebrew, Hungarian, Indonesian, Italian, Japanese, Kazakh, Korean, Latvian, Lithuanian, Norwegian, Polish, Portuguese, Romanian, Russian, Serbian, Slovak,
Spanish, Swedish, Thai, Turkish, Ukrainian, Vietnamese
Input/output terminals
Digital input/output
USB 2.0 High-Speed, MTP/PTP
106
Appendix
Specifications
Power supply/other
Power supply
NP-45A rechargeable battery
Battery life (approximate
Battery type
Approximate number of frames
number of frames that can
NP-45A (type supplied with camera)
220
be taken with a fully-charged
battery)
CIPA standard, measured in B (auto) mode using battery supplied with camera and SD memory card.
Camera dimensions
(W × H × D)
Camera weight
Shooting weight
Operating conditions
Appendix
Note: Number of shots that can be taken with battery varies with battery charge level and will
Note:
decline at low temperatures.
95.4 mm × 56.9 mm × 20.1 mm/3.7in. × 2.2in. × 0.7in.,
excluding projections (minimum depth 17.45 mm/0.6 in.)
Approx. 133 g/4.6 oz., excluding battery, accessories, and memory card
Approx. 150 g/5.2 oz., including battery and memory card
• Temperature
Temperature:: 0 °C – +40 °C/+32 °F – +104 °F
• Humidity
Humidity:: 10% – 80% (no condensation)
107
Specifications
NP-45A rechargeable battery
Nominal voltage
DC 3.7 V
Nominal capacity
720 mAh
Operating temperature 0 °C – +40 °C/+32 °F – +104 °F
Dimensions (W × H × D) 31.0 mm × 39.6 mm × 6.0 mm/1.2 in. × 1.6 in. × 0.2 in.
Weight
Approx. 15.5 g/0.5 oz.
BC-45B battery charger
Rated input
Input capacity
Rated output
Supported batteries
Charging time
Operating temperature
Dimensions (W × H × D)
Weight
100 V–240 V AC, 50/60 Hz
6.0 V (100 V/240 VA)
4.2 V DC, 550 mA
NP-45A rechargeable batteries
Approx. 120 minutes (+20 °C/+68 °F)
0 °C – +40 °C/+32 °F – +104 °F
46 mm × 91 mm × 23 mm/1.8 in. × 3.6 in. × 0.9 in., excluding projections
Approx. 65 g/2.2 oz., excluding battery
Weight and dimensions vary with the country or region of sale.
108
Appendix
Specifications
■ Notices
• Specifications subject to change without notice. FUJIFILM shall not be held liable for
damages resulting from errors in this manual.
• Although the LCD monitor is manufactured using advanced high-precision technology, small bright points and anomalous colors may appear, particularly in the vicinity
of text. This is normal for this type of LCD monitor and does not indicate a malfunction; images recorded with the camera are unaffected.
• Digital cameras may malfunction when exposed to strong radio interference (e.g.,
electric fields, static electricity, or line noise).
• Due to the type of lens used, some distortion may occur at the periphery of images.
This is normal.
Appendix
109
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN
http://www.fujifilm.com/products/digital_cameras/index.html
Restrictions on Camera Settings
The options available in each shooting mode are listed below.
Option
B OFF
N
B ON
Q
N
O
K
L
M
P
S/R
h
a/g
F
F
H
d
AUTO
3200
1600
800
N
400
200
100
O
O
P
Q
h1280
V
f
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔
✔ ✔
✔
✔
✔
✔1
✔1
✔
✔
✔
✔
✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
Shooting Mode
SP
L Z M N O HQR S U V W
✔ ✔
✔
✔ ✔ ✔2
✔ ✔
✔
✔ ✔ ✔
✔
✔2
✔ ✔
✔ ✔
✔ ✔
✔ ✔ ✔2
✔ ✔
✔ ✔ ✔
✔2
✔ ✔
✔ ✔
✔ ✔ ✔2 ✔ ✔ ✔ ✔ ✔ ✔
✔2 ✔ ✔2 ✔2
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔
✔ ✔
✔ ✔ ✔ ✔ ✔ ✔
✔ ✔
✔2 ✔2
✔ ✔
✔2 ✔2 ✔2 ✔2 ✔2 ✔2 ✔2 ✔2 ✔2 ✔2
✔2 ✔ ✔
✔2 ✔2 ✔2 ✔2 ✔2 ✔2 ✔2 ✔2 ✔2 ✔2 ✔2 ✔2 ✔2 ✔2 ✔2 ✔2 ✔2 ✔2 ✔2
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔
✔ ✔
✔ ✔
F
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Restrictions on Camera Settings
Option
T
P
FINE
NORMAL
c
a
b
f
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
ON
OFF
B ON
B OFF
OFF
✔
✔
✔
✔
L
✔
✔
✔
Shooting Mode
SP
Z M N O HQR S U
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
D
R
b
AUTO
OFF
✔
✔
✔
ON
OFF
✔
✔
✔
c
L
D
M
E
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔ ✔
✔ ✔ ✔
✔
✔
✔2 ✔2 ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔ ✔
✔ ✔ ✔
✔
✔
✔2 ✔2 ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
1 The camera automatically analyzes and selects macro mode ON/OFF.
2 Automatically optimized for selected shooting mode.
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
VW
✔ ✔
✔ ✔ ✔
✔ ✔ ✔2 ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔
✔
✔
✔ ✔
✔
✔
✔ ✔
✔
✔
✔ ✔ ✔
✔ ✔ ✔
✔2 ✔2 ✔2 ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔
F
✔
✔
✔
✔
✔
✔
✔