Owner`s manual | FujiFilm 16202014 Digital Camera User Manual

BL04701-101
DIGITAL CAMERA
X-T1
Owner’s Manual
Thank you for your purchase of this product. This
manual describes how to use your FUJIFILM X-T1
digital camera and install the supplied software. Be
sure that you have read and understood its contents
before using the camera.
EN
Before You Begin
First Steps
Basic Photography
and Playback
Basic Movie Recording
and Playback
The Q (Quick Menu) Button
The Fn (Function) Buttons
More on Photography
and Playback
Menus
For information on related products, visit our website at:
http://www.fujifilm.com/products/digital_cameras/index.html
For more information on the X-T1, visit:
http://fujifilm-x.com/x-t1/
Connections
Technical Notes
Troubleshooting
Appendix
For Your Safety
IMPORTANT SAFETY INSTRUCTIONS
• Read Instructions
Instructions: All the safety and operating instructions
should be read before the appliance is operated.
• Retain Instructions
Instructions: The safety and operating instructions
should be retained for future reference.
• Heed Warnings
Warnings: All warnings on the appliance and in the
operating instructions should be adhered to.
• Follow Instructions
Instructions: All operating and use instructions
should be followed.
Installation
Power Sources: This video product should be operated only
from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your
home, consult your appliance dealer or local power company. For video products intended to operate from battery
power, or other sources, refer to the operating instructions.
This video product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation
is provided or the manufacturer’s instructions have been
adhered to. This video product should never be placed near
or over a radiator or heat register.
Attachments: Do not use attachments not recommended by
the video product manufacturer as they may cause hazards.
Water and Moisture: Do not use this video product near water—for example, near a bath tub, wash bowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming pool,
and the like.
Power-Cord Protection: Power-supply cords should be routed
so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the
Grounding or Polarization: This video product is equipped point where they exit from the appliance.
with a polarized alternating-current line plug (a plug having
one blade wider than the other). This plug will fit into the Accessories: Do not place this video product on an unstable
power outlet only one way. This is a safety feature. If you cart, stand, tripod, bracket, or table. The video product may
are unable to insert the plug fully into the outlet, try revers- fall, causing serious injury to a child or adult, and serious
ing the plug. If the plug should still fail to fit, contact your damage to the appliance. Use only with a cart, stand, trielectrician to replace your obsolete outlet. Do not defeat pod, bracket, or table recommended by the manufacturer, or
sold with the video product. Any mounting of the appliance
the safety purpose of the polarized plug.
should follow the manufacturer’s instructions, and should use
Alternate Warnings: This video product is equipped with a mounting accessory recommended by the manufacturer.
a three-wire grounding-type plug, a plug having a third
(grounding) pin. This plug will only fit into a grounding- An appliance and cart combination
type power outlet. This is a safety feature. If you are unable should be moved with care. Quick
to insert the plug into the outlet, contact your electrician to stops, excessive force, and uneven
replace your obsolete outlet. Do not defeat the safety pur- surfaces may cause the appliance
and cart combination to overturn.
pose of the grounding type plug.
Overloading: Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
Ventilation: Slots and openings in the cabinet are provided
for ventilation, to ensure reliable operation of the video
product and to protect it from overheating, and these openings must not be blocked or covered. The openings should
never be blocked by placing the video product on a bed,
sofa, rug, or other similar surface.
ii
Antennas
Outdoor Antenna Grounding: If an outside antenna or cable
system is connected to the video product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA No. 70,
provides information with respect to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
Ground Clamp
Antenna Lead
in Wire
Electric Service
Equipment
Antenna
Discharge Unit
(NEC SECTION
810-20)
Ground Clamps
Power Service Grounding Electrode
System (NEC ART 250. PART H)
Grounding Conductors
(NEC SECTION 810-21)
Power Lines: An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power
lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such
power lines or circuits as contact with them might be fatal.
Use
Cleaning: Unplug this video product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
Object and Liquid Entry: Never push objects of any kind into this
video product through openings as they may touch dangerous
voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the video product.
Lightning: For added protection for this video product receiver during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will
prevent damage to the video product due to lightning and
power-line surges.
For Your Safety
Service
Be sure to read these notes before use
Servicing: Do not attempt to service this video product
Safety Notes
yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to • Make sure that you use your camera correctly. Read these
qualified service personnel.
safety notes and your Owner’s Manual carefully before use.
Damage Requiring Service: Unplug this video product from • After reading these safety notes, store them in a safe place.
the wall outlet and refer servicing to qualified service perAbout the Icons
sonnel under the following conditions:
The icons shown below are used in this document to indi• When the power-supply cord or plug is damaged
cate the severity of the injury or damage that can result if the
• If liquid has been spilled, or objects have fallen into the
information indicated by the icon is ignored and the product
video product.
is used incorrectly as a result.
• If the video product has been exposed to rain or water.
• If the video product has been dropped or the cabinet has
This icon indicates that death or seribeen damaged.
WARNING ous injury can result if the information
If the video product does not operate normally follow the
is ignored.
operating instructions. Adjust only those controls that are
This icon indicates that personal injury
covered by the operating instructions as an improper adjustCAUTION or material damage can result if the inment of other controls may result in damage and will often
formation is ignored.
require extensive work by a qualified technician to restore
The icons shown below are used to indicate the nature of the
the video product to its normal operation.
instructions which are to be observed.
When the video product exhibits a distinct change in perforTriangular icons tell you that this information remance — this indicates a need for service.
quires attention (“Important”).
Replacement Parts: When replacement parts are required,
Circular icons with a diagonal bar tell you that the
be sure the service technician has used replacement parts
action indicated is prohibited (“Prohibited”).
specified by the manufacturer or have the same characterFilled circles with an exclamation mark indicate an
action that must be performed (“Required”).
istics as the original part. Unauthorized substitutions may
result in fire, electric shock or other hazards.
Safety Check: Upon completion of any service or repairs to
this video product, ask the service technician to perform
safety checks to determine that the video product is in
proper operating condition.
WARNING
Unplug
from power
socket
If a problem arises, turn the camera off, remove the
battery, and disconnect and unplug the AC power
adapter. Continued use of the camera when it
is emitting smoke, is emitting any unusual odor,
or is in any other abnormal state can cause a fire
or electric shock. Contact your FUJIFILM dealer.
Do not allow water or foreign objects to enter the
camera. If water or foreign objects get inside the
camera, turn the camera off, remove the battery,
and disconnect and unplug the AC power adapter. Continued use of the camera can cause a fire
or electric shock. Contact your FUJIFILM dealer.
WARNING
Do not use in
the bathroom
or shower
Do not disassemble
Do not touch
internal parts
Do not use the camera in the bathroom or shower.
This can cause a fire or electric shock.
Never attempt to change or take apart the camera
(never open the case). Failure to observe this precaution can cause fire or electric shock.
Should the case break open as the result of a fall or
other accident, do not touch the exposed parts. Failure to observe this precaution could result in electric shock or in injury from touching the damaged
parts. Remove the battery immediately, taking
care to avoid injury or electric shock, and take the
product to the point of purchase for consultation.
Do not change, heat or unduly twist or pull the connection cord and do not place heavy objects on the
connection cord. These actions could damage the
cord and cause a fire or electric shock. If the cord
is damaged, contact your FUJIFILM dealer.
Do not place the camera on an unstable surface. This
can cause the camera to fall or tip over and cause
injury.
Never attempt to take pictures while in motion. Do
not use the camera while walking or driving. This
can result in you falling down or being involved in
a traffic accident.
Do not touch any metal parts of the camera during
a thunderstorm. This can cause an electric shock
due to induced current from the lightning discharge.
Do not use the battery except as specified. Load the
battery as shown by the indicator.
Do not heat, change or take apart the battery. Do not
drop or subject the battery to impacts. Do not store
the battery with metallic products.
products. Any of these actions can cause the battery to burst or leak and
cause fire or injury as a result.
iii
For Your Safety
WARNING
Use only batteries or AC power adapters specified for
use with this camera. Do not use voltages other than
the power supply voltage shown. The use of other
power sources can cause a fire.
If the battery leaks and fluid gets in contact with your
eyes, skin or clothing, flush the affected area with
clean water and seek medical attention or call an
emergency number right away.
Do not use the charger to charge batteries other than
those specified here. The supplied charger is for
use only with batteries of the type supplied with
the camera. Using the charger to charge conventional batteries or other types of rechargeable
batteries can cause the battery to leak, overheat
or burst.
Do not use in the presence of flammable objects, explosive gases, or dust.
When carrying the battery, install it in a digital camera or keep it in the hard case. When storing the battery, keep it in the hard case. When discarding, cover
the battery terminals with insulation tape. Contact
with other metallic objects or batteries could
cause the battery to ignite or burst.
Keep the hot shoe cover and memory cards out of the
reach of small children. These items are small and
easy for children to swallow. Store out of reach
of small children. Should a child swallow one of
these items, seek medical attention or call emergency immediately.
CAUTION
Do not use this camera in locations affected by oil
fumes, steam, humidity or dust. This can cause a
fire or electric shock.
Do not leave this camera in places subject to extremely
high temperatures. Do not leave the camera in
locations such as a sealed vehicle or in direct sunlight. This can cause a fire.
iv
CAUTION
Keep out of the reach of small children. This product
could cause injury in the hands of a child.
Do not place heavy objects on the camera. This can
cause the heavy object to tip over or fall and
cause injury.
Do not move the camera while the AC power adapter
is still connected. Do not pull on the connection cord
to disconnect the AC power adapter. This can damage the power cord or cables and cause a fire or
electric shock.
Do not cover or wrap the camera or the AC power
adapter in a cloth or blanket. This can cause heat
to build up and distort the casing or cause a fire.
When you are cleaning the camera or you do not plan
to use the camera for an extended period, remove
the battery and disconnect and unplug the AC power
adapter. Failure to do so can cause a fire or electric shock.
When charging ends, unplug the charger from the
power socket. Leaving the charger plugged into
the power socket can cause a fire.
Using a flash too close to a person’s eyes may temporarily affect the eyesight
eyesight.. Take particular care when
photographing infants and young children.
When a memory card is removed, the card could come
out of the slot too quickly. Use your finger to hold it
and gently release the card. Injury could result to
those struck by the ejected card.
Request regular internal testing and cleaning for
your camera. Build-up of dust in your camera
can cause a fire or electric shock. Contact your
FUJIFILM dealer to request internal cleaning every
two years. Please note that this service is not free
of charge.
Danger of explosion if battery is incorrectly replaced.
Replace only with batteries of the same type.
The Battery and Power Supply
Note: Check the type of battery used in your camera and
read the appropriate sections.
The following describes the proper use of batteries and how
to prolong their life. Incorrect use can shorten battery life or
cause leakage, overheating, fire, or explosion.
Li-ion Batteries
Read this section if your camera uses a rechargeable
Li-ion battery.
The battery is not charged at shipment. Charge the battery
before use. Keep the battery in its case when not in use.
■ Notes on the Battery
The battery gradually loses its charge when not in use.
Charge the battery one or two days before use.
Battery life can be extended by turning the camera off when
not in use.
Battery capacity decreases at low temperatures; a depleted
battery may not function at when cold. Keep a fully charged
spare battery in a warm place and exchange as necessary,
or keep the battery in your pocket or other warm place and
insert it in the camera only when shooting. Do not place
the battery in direct contact with hand warmers or other
heating devices.
■ Charging the Battery
Charge the battery in the supplied battery charger. Charging times will increase at ambient temperatures below
+10 °C (+50 °F) or above +35 °C (+95 °F). Do not attempt
to charge the battery at temperatures above 40 °C (+104 °F);
at temperatures below 0 °C (+32 °F), the battery will not
charge.
Do not attempt to recharge a fully charged battery. The battery does not however need to be fully discharged before
charging.
The battery may be warm to the touch immediately after
charging or use. This is normal.
For Your Safety
■ Battery Life
At normal temperatures, the battery can be recharged about
300 times. A noticeable decrease in the length of time the
battery will hold a charge indicates that it has reached the
end of its service life and should be replaced.
■ Storage
Performance may be impaired if the battery is left unused
for extended periods when fully charged. Run the battery
flat before storing it.
If the camera will not be used for an extended period, remove the battery and store it in a dry place with an ambient
temperature of from +15 °C to +25 °C (+59 °F to +77 °F). Do
not store in locations exposed to extremes of temperature.
■ Cautions: Handling the Battery
• Do not transport or store with metal objects such as necklaces or hairpins.
• Do not expose to flame or heat.
• Do not disassemble or modify.
• Use with designated chargers only.
• Dispose of used batteries promptly.
• Do not drop or subject to strong physical shocks.
• Do not expose to water.
• Keep the terminals clean.
• The battery and camera body may become warm to the
touch after extended use. This is normal.
AA Alkaline/Rechargeable Ni-MH Batteries
Read this section if your camera uses AA alkaline or rechargeable AA Ni-MH batteries. Information on compatible battery types may be found elsewhere in the camera
manual.
■ Cautions: Handling the Batteries
• Do not expose to water, flame, or heat, or store in warm or
humid conditions.
• Do not transport or store with metal objects such as necklaces or hairpins.
• Do not disassemble or modify the batteries or battery
casing.
• Do not subject to strong physical shocks.
• Do not use batteries that are leaking, deformed, or discolored.
• Keep out of reach of infants and small children.
• Insert in the correct orientation.
• Do not mix old and new batteries, batteries with different
charge levels, or batteries of different types.
• If the camera will not be used for an extended period, remove the batteries. Note that the camera clock will be reset.
• The batteries may be warm to the touch immediately after
use. Turn the camera off and allow the batteries to cool
before handling.
• Battery capacity tends to decrease at low temperatures.
Keep spare batteries in a pocket or other warm place and
exchange as necessary. Cold batteries may recover some
of their charge when warmed.
• Fingerprints and other stains on the battery terminals
can impair battery performance. Thoroughly clean the
terminals with a soft, dry cloth before inserting them in
the camera.
The camera draws a small amount of current even when off.
Ni-MH batteries that have been left in the camera for an extended period may be drawn down to the point that they no
longer hold a charge. Battery performance may also drop if
the batteries are run down in a device such as a flashlight. Use
the discharge option in the camera setup menu to discharge
Ni-MH batteries. Batteries that no longer hold a charge
even after repeatedly being discharged and recharged have
reached the end of their service life and must be replaced.
Ni-MH batteries can be recharged in a battery charger (sold
separately). Batteries may become warm to the touch after
charging. Refer to the instructions provided with the charger
for more information. Use the charger with compatible batteries only.
Ni-MH batteries gradually lose their charge when not in use.
■ Disposal
CAUTION: Dispose of used batteries in accord with local
regulations.
If the batteries leak, clean the battery compartment AC Power Adapters (Available Separately)
thoroughly before inserting new batteries.
This section applies to all camera models. Use only
If fluid from the battery comes into contact with skin FUJIFILM AC power adapters designated for use with this
or clothing, flush the affected area with water. If camera. Other adapters could damage the camera.
fluid enters your eyes, immediately flush the affected • The AC power adapter is for indoor use only.
area with water and seek medical attention. Do not rub • Be sure the DC plug is securely connected to the camera.
your eyes. Failure to observe this precaution could result • Turn the camera off before disconnecting the adapter.
Disconnect the adapter by the plug, not the cable.
in permanent visual impairment.
impairment
• Do not use with other devices.
■ Ni-MH Batteries
• Do not disassemble.
The capacity of Ni-MH batteries may be temporarily reduced
• Do not expose to high heat and humidity.
when new, after long periods of disuse, or if they are repeat• Do not subject to strong physical shocks.
edly recharged before being fully discharged. This is normal
• The adapter may hum or become hot to the touch during
and does not indicate a malfunction. Capacity can be inuse. This is normal.
creased by repeatedly discharging the batteries using the
• If the adapter causes radio interference, reorient or relocate
discharge option in the camera setup menu and recharging
the receiving antenna.
them using a battery charger.
Q CAUTION: Do not use the discharge option with alkaline
batteries.
v
For Your Safety
Using the Camera
• Do not aim the camera at extremely bright light sources,
such as the sun in a cloudless sky. Failure to observe this
precaution could damage the camera image sensor.
• Strong sunlight focused through the viewfinder may damage the panel of electronic viewfinder (EVF). Do not aim
the electronic viewfinder at the sun.
Liquid Crystal
In the event that the display is damaged, care should be
taken to avoid contact with liquid crystal. Take the urgent
action indicated should any of the following situations arise:
• If liquid crystal comes in contact with your skin, clean the
area with a cloth and then wash thoroughly with soap and
running water.
• If liquid crystal enters your eyes, flush the affected eye with
clean water for at least 15 minutes and then seek medical
assistance.
• If liquid crystal is swallowed, rinse your mouth thoroughly
with water. Drink large quantities of water and induce
vomiting, then seek medical assistance.
Take Test Shots
Before taking photographs on important occasions (such as
at weddings or before taking the camera on a trip), take a
test shot and view the results to ensure that the camera is
functioning normally. FUJIFILM Corporation can not accept
liability for damages or lost profits incurred as a result of
Although the display is manufactured using extremely highproduct malfunction.
precision technology, it may contain pixels that are always lit
Notes on Copyright
or that do not light. This is not a malfunction, and images
Unless intended solely for personal use, images recorded usrecorded with the product are unaffected.
ing your digital camera system cannot be used in ways that
infringe copyright laws without the consent of the owner. Trademark Information
Note that some restrictions apply to the photographing of Digital Split Image is a trademark or registered trademark
stage performances, entertainments, and exhibits, even of FUJIFILM Corporation. xD-Picture Card and E are
when intended purely for personal use. Users are also asked trademarks of FUJIFILM Corporation. The typefaces includto note that the transfer of memory cards containing images ed herein are solely developed by DynaComware Taiwan
or data protected under copyright laws is only permissible Inc. Macintosh, QuickTime, and Mac OS are trademarks
of Apple Inc. in the U.S.A. and other countries. Windows
within the restrictions imposed by those copyright laws.
8, Windows 7, Windows Vista, and the Windows logo are
Handling
trademarks of the Microsoft group of companies. Wi-Fi® and
To ensure that images are recorded correctly, do not subject
Wi-Fi Protected Setup® are registered trademarks of the Wi-Fi
the camera to impact or physical shocks while images are
Alliance. Adobe and Adobe Reader are either trademarks or
being recorded.
registered trademarks of Adobe Systems Incorporated in the
U.S.A. and/or other countries. The SDHC and SDXC logos
are trademarks of SD-3C, LLC. The HDMI logo is a trademark.
YouTube is a trademark of Google Inc. All other trade names
mentioned in this manual are the trademarks or registered
trademarks of their respective owners.
Electrical Interference
This camera may interfere with hospital or aviation equipment. Consult with hospital or airline staff before using the
camera in a hospital or on an aircraft.
vi
Color Television Systems
NTSC (National Television System Committee) is a color television telecasting specification adopted mainly in the U.S.A.,
Canada, and Japan. PAL (Phase Alternation by Line) is a color
television system adopted mainly in European countries and
China.
Electrical Interference
Exif Print is a newly revised digital camera file format in
which information stored with photographs is used for optimal color reproduction during printing.
IMPORTANT NOTICE: Read Before Using the Software
Direct or indirect export, in whole or in part, of licensed software without the permission of the applicable governing
bodies is prohibited.
NOTICES
To prevent fire or shock hazard, do not expose the unit
to rain or moisture.
Please read the “Safety Notes” and make sure you understand them before using the camera.
Perchlorate Material—special handling may apply. See
http://www.dtsc.ca.gov/hazardouswaste/perchlorate.
For Your Safety
For Customers in the U. S. A.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
Radiation Exposure Statement: This device meets the government’s requirements for exposure to radio waves. This device is
designed and manufactured not to exceed the emission limits
for exposure to radio frequency (RF) energy set by the Federal
Communications Commission of the U.S. Government.
Disposal of Electrical and Electronic Equipment in Private Households
In the European Union, Norway, Iceland and
Liechtenstein: This symbol on the product, or in
the manual and in the warranty, and/or on its
packaging indicates that this product shall not
The exposure standard for wireless device employs a unit be treated as household waste. Instead it should
of measurement known as the Specific Absorption Rate, or be taken to an applicable collection point for the
Contains IC : 7736B-02000002
SAR. The SAR limit set by the FCC is 1.6W/kg. *Tests for SAR recycling of electrical and electronic equipment.
Contains FCC ID : W2Z-02000002
are conducted using standard operating positions accepted By ensuring this product is disposed of correctly, you will
FCC Statement: This device complies with Part 15 of the FCC by the FCC with the device transmitting at its highest certihelp prevent potential negative consequences to the enRules. Operation is subject to the following two conditions: fied power level in all tested frequency bands.
vironment and human health, which could otherwise be
(1) This device may not cause harmful interference, and
caused by inappropriate waste handling of this product.
(2) this device must accept any interference received, includ- Notes on the Grant: To comply with Part 15 of the FCC Rules,
this product must be used with a Fujifilm-specified ferrite- This symbol on the batteries or accumulators ining interference that may cause undesired operation.
core A/V cable, USB cable, and DC supply cord.
dicates that those batteries shall not be treated
CAUTION: This equipment has been tested and found to comas household waste.
ply with the limits for a Class B digital device, pursuant to
A lithium ion battery that is recyclable
Part 15 of the FCC Rules. These limits are designed to proIf your equipment contains easy removable batteries or
powers the product you have purchased.
vide reasonable protection against harmful interference in a
accumulators please dispose these separately according to
Please call 1-800-8-BATTERY for informaresidential installation. This equipment generates, uses, and
your local requirements.
tion on how to recycle this battery.
can radiate radio frequency energy and, if not installed and
The recycling of materials will help to conserve natural reused in accordance with the instructions, may cause harmful
For Customers in Canada
sources. For more detailed information about recycling this
interference to radio communications. However, there is no
CAN ICES-3 (B)/NMB-3(B)
product, please contact your local city office, your household
guarantee that interference will not occur in a particular inCAUTION: This Class B digital apparatus complies with Cana- waste disposal service or the shop where you purchased the
stallation. If this equipment does cause harmful interference
dian ICES-003.
product.
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged Industry Canada statement: This device complies with RSS- In Countries Outside the European Union, Norway, Iceland and
to try to correct the interference by one or more of the fol- 210 of the Industry Canada Rules. Operation is subject to Liechtenstein: If you wish to discard this product, including
the following two conditions: (1) This device may not cause the batteries or accumulators, please contact your local aulowing measures:
harmful interference, and (2) this device must accept any thorities and ask for the correct way of disposal.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver. interference received, including interference that may cause
In Japan: This symbol on the batteries indicates
• Connect the equipment into an outlet on a circuit different undesired operation.
that they are to be disposed of separately.
from that to which the receiver is connected.
This device and its antenna(s) must not be co-located or op• Consult the dealer or an experienced radio/TV technician erating in conjunction with any other antenna or transmitfor help.
ter, except tested built-in radios. The County Code Selection
FCC Caution: Any changes or modifications not expressly ap- feature is disabled for products marketed in the US/ Canada.
proved by the party responsible for compliance could void Radiation Exposure Statement: The product comply with the
the user’s authority to operate this equipment.
Canada portable RF exposure limit set forth for an unconThis transmitter must not be co-located or operating in con- trolled environment and are safe for intended operation as
described in this manual. The further RF exposure reduction
junction with any other antenna or transmitter.
can be achieved if the product can be kept as far as possible
from the user body or set the device to lower output power
if such function is available.
vii
For Your Safety
Be sure to read these notes before use
Safety Notes
Thank you for your purchase of this product. For repair, inspection, and internal testing, contact your FUJIFILM dealer.
• Make sure that you use the lens correctly. Read these safety notes and the camera Owner’s
Manual carefully before use.
• After reading these safety notes, store them in a safe place.
About the Icons
The icons shown below are used in this document to indicate the severity of the injury or
damage that can result if the information indicated by the icon is ignored and the product
is used incorrectly as a result.
This icon indicates that death or serious injury can result if the information is ignored.
This icon indicates that personal injury or material damage can result if
CAUTION
the information is ignored.
WARNING
The icons shown below are used to indicate the nature of the instructions which are to be
observed.
Triangular icons tell you that this information requires attention (“Important”).
Circular icons with a diagonal bar tell you that the action indicated is prohibited
(“Prohibited”).
Filled circles with an exclamation mark indicate an action that must be performed
(“Required”).
WARNING
Do not use in
the bathroom or
shower
Do not disassemble
Do not touch
internal parts
viii
Do not immerse in or expose to water. Failure to observe this precaution can cause
a fire or electric shock.
Do not disassemble (do not open the case). Failure to observe this precaution can
cause fire, electric shock, or injury due to product malfunction.
Should the case break open as the result of a fall or other accident, do not touch the
exposed parts. Failure to observe this precaution could result in electric shock
or in injury from touching the damaged parts. Remove the camera battery
immediately, taking care to avoid injury or electric shock, and take the product
to the point of purchase for consultation.
WARNING
Do not place on unstable surfaces. The product may fall, causing injury.
Do not view the sun through the lens or camera viewfinders. Failure to observe this
precaution can cause permanent visual impairment.
CAUTION
Do not use or store in locations that are exposed to steam, or smoke or are very humid
or extremely dusty. Failure to observe this precaution can cause fire or electric
shock.
Do not leave in direct sunlight or in locations subject to very high temperatures, such
as in a closed vehicle on a sunny day. Failure to observe this precaution can cause
fire.
Keep out of the reach of small children. This product could cause injury in the
hands of a child.
Do not handle with wet hands. Failure to observe this precaution can cause
electric shock.
Keep the sun out of the frame when shooting backlit subjects. Sunlight focused into
the camera when the sun is in or close to the frame can cause fire or burns.
When the product is not in use, replace the lens caps and store out of direct sunlight.
Sunlight focused by the lens can cause fire or burns.
Do not carry the camera or lens while they are attached to a tripod. The product can
fall or strike other objects, causing injury.
For Your Safety
European Union regulatory notice
This product complies with the following EU Directives:
• Low Voltage Directive 2006/95/EC
• EMC Directive 2004/108/EC
• R & TTE Directive 1999/5/EC
Wireless Network Devices: Cautions
• This device operates on the same frequency as commercial, educational, and medical devices and
wireless transmitters. It also operates on the same frequency as licensed transmitters and
special unlicensed low-voltage transmitters used in RFID tracking systems for assembly
lines and in other similar applications.
To prevent interference with the above devices, observe the following precautions. Confirm that
•
Compliance with these directives implies conformity to applicable harmonized European
the RFID transmitter is not in operation before using this device. Should you observe that
standards (European Norms) which are listed on the EU Declaration of Conformity issued by
the device causes interference in licensed transmitters used for RFID tracking, immediately
FUJIFILM Corporation for this product or product family.
choose a new operating frequency for this device to prevent additional interference. If you
This compliance is indicated by the following conformity marking placed on the product:
notice that this device causes interference in low-voltage RFID tracing systems, contact a
FUJIFILM representative.
This marking is valid for non-Telecom products and EU harmonized Telecom products (e.g.
Bluetooth).
2.4DS/OF4
This sticker indicates that this device operates in the 2.4 GHz
band using DSSS and OFDM modulation and may cause interference at distances of up to 40 m.
Regarding the Declaration of Conformity, visit http://www.fujifilm.com/products/digital_
cameras/x/fujifilm_x_t1/pdf/index/fujifilm_x_t1_cod.pdf.
IMPORTANT: Read the following notices before using the camera’s built-in wireless
transmitter.
Q This product, which contains encryption function developed in the United States, is controlled by the United States Export Administration Regulations and may not be exported
or re-exported to any country to which the United States embargoes goods.
• Use only as part of a wireless network. FUJIFILM does not accept liability for damages resulting from unauthorized use. Do not use in applications requiring a high degree of reliability,
for example in medical devices or other systems that may directly or indirectly impact
human life. When using the device in computer and other systems that demand a greater
degree of reliability than wireless networks, be sure to take all necessary precautions to
ensure safety and prevent malfunction.
• Use only in the country in which the device was purchased. This device conforms to regulations
governing wireless network devices in the country in which it was purchased. Observe all
location regulations when using the device. FUJIFILM does not accept liability for problems arising from use in other jurisdictions.
• Wireless data (images) may be intercepted by third parties. The security of data transmitted
over wireless networks is not guaranteed.
• Do not use the device in locations subject to magnetic fields, static electricity, or radio interference.
Do not use the transmitter in the vicinity of microwave ovens or in other locations subject
to magnetic fields, static electricity, or radio interference that may prevent reception of
wireless signals. Mutual interference may occur when the transmitter is used in the vicinity
of other wireless devices operating in the 2.4 GHz band.
• The wireless transmitter operates in the 2.4 GHz band using DSSS and OFDM modulation.
ix
About This Manual
Before using the camera, read this manual and the warnings in “For Your Safety” (P ii). For information
on specific topics, consult the sources below.
Table of Contents ................................................. P xii
The “Table of Contents” gives an overview of the
entire manual. The principal camera operations
are listed here.
Troubleshooting ................................................P
................................................ P 117
Having a specific problem with the camera?
Find the answer here.
Warning Messages and Displays .........................P
......................... P 122
Find out what’s behind that flashing icon or error
message in the display.
Memory Cards
Pictures are stored on optional SD, SDHC, and SDXC memory cards (P 16), referred to in this manual as “memory
cards.”
x
Product Care
Camera body: For continued enjoyment of your camera, use a soft, dry cloth to clean the camera body
after each use. Do not use alcohol, thinner, or other volatile chemicals, which could discolor or deform
the leather on the camera body. Any liquid on the camera should be removed immediately with a
soft, dry cloth. Use a blower to remove dust from the monitor, taking care to avoid scratches, and then
gently wipe with a soft, dry cloth. Any remaining stains can be removed by wiping gently with a piece
of FUJIFILM lens-cleaning paper to which a small amount of lens-cleaning fluid has been applied. To
prevent dust entering the camera, replace the body cap when no lens is in place.
Image sensor: Dust can be removed from the image sensor using the V SENSOR CLEANING option in
the setup menu (P 92).
Interchangeable lenses: Use a blower to remove dust, then gently wipe with a soft, dry cloth. Any remaining stains can be removed by wiping gently with a piece of FUJIFILM lens-cleaning paper to which a
small amount of lens-cleaning fluid has been applied. Replace the front and rear caps when the lens
is not use.
xi
Table of Contents
For Your Safety .....................................................................................ii
IMPORTANT SAFETY INSTRUCTIONS.........................................ii
Safety Notes .......................................................................................iii
NOTICES ...............................................................................................vi
Safety Notes .....................................................................................viii
About This Manual .............................................................................x
Product Care ........................................................................................xi
Before You Begin
Symbols and Conventions..............................................................1
Supplied Accessories ........................................................................1
Parts of the Camera ...........................................................................2
The Selector ........................................................................................4
Camera Displays ................................................................................5
Shooting: LCD Monitor/Viewfinder ........................................5
Shooting: LCD Monitor ................................................................6
Playback: Viewfinder/LCD Monitor .........................................6
Lenses ......................................................................................................7
Parts of the Lens ................................................................................7
Removing the Caps ..........................................................................7
Attaching the Hood .........................................................................7
Lenses with Aperture Rings ..........................................................8
Lenses with No Aperture Rings ...................................................8
Lenses with O.I.S. Switches............................................................9
Manual Focus Lenses.......................................................................9
xii
First Steps
Attaching the Strap ........................................................................ 10
Attaching a Lens .............................................................................. 12
Charging the Battery ..................................................................... 13
Inserting the Battery...................................................................... 14
Inserting a Memory Card ............................................................. 15
Compatible Memory Cards ..................................................... 16
Turning the Camera on and Off ................................................ 17
Basic Setup ......................................................................................... 18
Display Settings ............................................................................... 19
Choosing a Display........................................................................ 19
The Viewfinder Display ................................................................ 20
Focusing the Viewfinder ............................................................. 20
Adjusting Display Brightness .................................................... 20
The DISP/BACK Button ....................................................................... 21
Viewfinder: Shooting ................................................................. 21
LCD Monitor: Shooting ............................................................. 21
Custom Display ............................................................................ 22
Viewfinder/LCD Monitor: Playback ...................................... 23
Basic Photography and Playback
Taking Photographs ....................................................................... 24
Viewing Pictures .............................................................................. 26
Viewing Pictures Full Frame....................................................... 26
Viewing Photo Information ....................................................... 27
Playback Zoom ............................................................................... 28
Multi-Frame Playback................................................................... 29
Deleting Pictures ............................................................................. 30
Table of Contents
Basic Movie Recording and Playback
More on Photography and Playback
Recording High-Definition (HD) Movies ............................... 31
Using an External Microphone ................................................. 32
Viewing Movies ................................................................................ 33
Choosing an Exposure Mode ..................................................... 46
Program AE (P) ................................................................................ 46
Shutter-Priority AE (S) .................................................................. 47
Aperture-Priority AE (A)............................................................... 48
Manual Exposure (M).................................................................... 49
Sensitivity ........................................................................................... 50
A (Auto) ........................................................................................... 51
Exposure Compensation .............................................................. 52
Metering .............................................................................................. 53
The DRIVE Dial .................................................................................. 54
Bracketing ......................................................................................... 54
Continuous Shooting (Burst Mode)........................................ 56
Multiple Exposures ........................................................................ 57
Advanced Filters ............................................................................. 58
Panoramas ........................................................................................ 59
Viewing Panoramas ...................................................................... 60
Focus Mode ........................................................................................ 61
The Focus Indicator .................................................................... 62
MF Assist ......................................................................................... 63
The Q (Quick Menu) Button
Using the Q Button ......................................................................... 35
The Self-Timer.................................................................................. 35
Flash Photography ........................................................................ 36
Intelligent Face Detection .......................................................... 38
The Fn (Function) Buttons
Default Roles ..................................................................................... 40
Bracketing and Advanced Filters (Fn1).................................. 40
Bracketing ...................................................................................... 40
Advanced Filters .......................................................................... 40
Wireless Options (Fn2) ................................................................. 41
Macro Mode (Fn3).......................................................................... 41
Film Simulation (Fn4) ................................................................... 42
White Balance (Fn5) ...................................................................... 43
Focus-Frame Selection (Fn6) ..................................................... 45
xiii
Table of Contents
Long Time-Exposures (T/B) ......................................................... 64
Time (T) .............................................................................................. 64
Bulb (B) ............................................................................................... 64
Interval Timer Photography....................................................... 65
Using a Remote Release .............................................................. 66
Focus/Exposure Lock ..................................................................... 67
Recording Pictures in RAW Format ......................................... 69
Creating JPEG Copies of RAW Pictures .................................. 70
Saving Settings................................................................................. 71
Using a Mount Adapter ................................................................ 72
Mount Adapter Settings.............................................................. 72
Choosing a Focal Length ......................................................... 72
Distortion Correction ................................................................ 72
Color Shading Correction ........................................................ 73
Peripheral Illumination Correction ...................................... 73
Image Search ..................................................................................... 74
PhotoBook Assist............................................................................. 75
Creating a PhotoBook .................................................................. 75
Viewing Photobooks .................................................................... 76
Editing and Deleting Photobooks........................................... 76
Menus
Using the Menus: Shooting Mode ........................................... 77
Shooting Menu Options (Photographs) ............................... 77
k BKT/Adv. SETTING ................................................................ 77
G AUTOFOCUS SETTING ........................................................ 78
N ISO AUTO SETTING............................................................... 78
xiv
O IMAGE SIZE.............................................................................. 79
T IMAGE QUALITY .................................................................... 79
U DYNAMIC RANGE.................................................................. 79
P FILM SIMULATION ................................................................ 79
B SELF-TIMER.............................................................................. 79
o INTERVAL TIMER SHOOTING ............................................ 80
D WHITE BALANCE ................................................................... 80
f COLOR ....................................................................................... 80
q SHARPNESS............................................................................. 80
r HIGHLIGHT TONE .................................................................. 80
s SHADOW TONE ..................................................................... 80
h NOISE REDUCTION............................................................... 80
K LONG EXPOSURE NR ........................................................... 80
j LENS MODULATION OPTIMIZER ..................................... 80
u SELECT CUSTOM SETTING ................................................ 80
K EDIT/SAVE CUSTOM SETTING .......................................... 80
l MOUNT ADAPTOR SETTING ............................................. 81
m SHOOT WITHOUT LENS ...................................................... 81
c MF ASSIST ................................................................................ 81
v AE/AF-LOCK MODE .............................................................. 81
d AF-LOCK MODE ..................................................................... 81
p FLASH MODE.......................................................................... 81
I FLASH COMPENSATION ..................................................... 81
B RED EYE REMOVAL ............................................................... 81
W MOVIE SET-UP ........................................................................ 82
L IS MODE ................................................................................... 82
r WIRELESS COMMUNICATION ........................................... 82
e APERTURE SETTING ............................................................. 82
Table of Contents
Using the Menus: Playback Mode............................................ 83
Playback Menu Options .............................................................. 83
r WIRELESS COMMUNICATION ........................................... 83
j RAW CONVERSION ............................................................... 83
A ERASE ........................................................................................ 83
G CROP.......................................................................................... 83
e RESIZE ....................................................................................... 84
D PROTECT .................................................................................. 84
C IMAGE ROTATE ....................................................................... 84
B RED EYE REMOVAL ............................................................... 85
I SLIDE SHOW ........................................................................... 85
m PHOTOBOOK ASSIST ........................................................... 85
j MARK FOR UPLOAD TO ...................................................... 86
b IMAGE SEARCH ...................................................................... 86
s PC AUTO SAVE ....................................................................... 86
K PRINT ORDER (DPOF) .......................................................... 86
J DISP ASPECT........................................................................... 87
The Setup Menu ............................................................................... 88
Using the Setup Menu ................................................................. 88
Setup Menu Options .................................................................... 89
F DATE/TIME ............................................................................... 89
N TIME DIFFERENCE ................................................................. 89
Q a ................................................................................ 89
R RESET......................................................................................... 89
o SILENT MODE ......................................................................... 89
b SOUND SET-UP ...................................................................... 90
A SCREEN SET-UP...................................................................... 90
F FUNCTION (Fn) SETTING.................................................... 91
e COMMAND DIAL SETTING ................................................ 91
N ISO DIAL SETTING................................................................. 91
I FOCUS RING............................................................................ 91
Z POWER MANAGEMENT ...................................................... 92
V SENSOR CLEANING .............................................................. 92
t SAVE DATA SET-UP ............................................................... 93
J COLOR SPACE ......................................................................... 93
r WIRELESS SETTINGS ............................................................ 94
s PC AUTO SAVE SETTING ..................................................... 94
U GEOTAGGING SET-UP .......................................................... 94
K FORMAT.................................................................................... 94
Factory Defaults ............................................................................... 95
xv
Table of Contents
Connections
Technical Notes
Wireless Transfer .............................................................................. 97
Wireless Connections: Smartphones ..................................... 97
Wireless Connections: Computers .......................................... 97
Viewing Pictures on a Computer .............................................. 98
Windows: Installing MyFinePix Studio .................................. 98
Macintosh: Installing RAW FILE CONVERTER.....................100
Connecting the Camera ............................................................101
Printing Pictures via USB ...........................................................103
Connecting the Camera ............................................................103
Printing Selected Pictures ........................................................103
Printing the DPOF Print Order ................................................104
Creating a DPOF Print Order....................................................105
WITH DATE s/ WITHOUT DATE ..........................................106
RESET ALL.....................................................................................107
Viewing Pictures on TV ...............................................................108
Optional Accessories....................................................................109
Accessories from FUJIFILM .......................................................109
Connecting the Camera to Other Devices .........................112
The Vertical Battery Grip ............................................................113
Parts of the VG-XT1 .....................................................................113
Attaching the VG-XT1.................................................................114
Inserting a Battery .......................................................................114
Caring for the Camera .................................................................115
Storage and Use ...........................................................................115
Traveling ..........................................................................................115
Cleaning the Image Sensor .......................................................116
Troubleshooting
Problems and Solutions .............................................................117
Warning Messages and Displays ............................................122
Appendix
Memory Card Capacity ...............................................................125
Specifications ..................................................................................126
Restrictions on Camera Settings ............................................131
xvi
Before You Begin
Symbols and Conventions
Menus and other text in the displays are shown in bold. In the illustrations in this manual, displays may
be simplified for explanatory purposes.
Supplied Accessories
Before You Begin
The following symbols are used in this manual:
Q This information should be read before use to ensure correct operation.
R Additional information that may be helpful when using the camera.
POther pages in this manual on which related information may be found.
The following items are included with the camera:
NP-W126 rechargeable battery
Clip attaching tool
BC-W126 battery charger
Metal strap clips (× 2)
Body cap
• Protective covers (× 2)
• Shoulder strap
• Hot shoe cover
(comes attached to hot shoe)
• Vertical battery grip
connector cover
EF-X8 shoe-mounted flash unit
• CD-ROM
• Owner’s Manual
(this manual)
R If you purchased a lens kit, check that a lens is included.
1
Parts of the Camera
For more information, refer to the page listed to the right of each item.
The LCD Monitor
The LCD monitor can be tilted for easier
viewing, but be careful not to touch the
wires or trap fingers or other objects behind the monitor. Touching the wires
could cause camera malfunction.
2
Parts of the Camera
i FOCUS ASSIST button ......................................62
j Memory card slot cover.....................................15
k Q (quick menu) button .....................................34
Custom settings button (press and hold) *
RAW conversion button (playback mode) .........70
l Selector/function buttons...................................4
m DISP (display)/BACK button ............................21
n Speaker.............................................................33
o Battery-chamber cover latch ............................14
p Battery-chamber cover .....................................14
q Tripod mount
r Vertical battery grip connector cover ...............113
s LCD monitor ...........................................2, 5, 6, 19
t Eye sensor .........................................................19
u Body cap ...........................................................12
v Memory card slot ..............................................15
w Battery chamber ...............................................14
x Battery latch .....................................................14
* For quick access to custom settings banks (P 71), press and hold while quick menu for still images (P 34) is displayed.
Before You Begin
A Exposure compensation dial .............................52 R AF-assist illuminator.........................................78
Self-timer lamp ................................................35
B Shutter button ..................................................25
C Fn2 button (function button 2) .................. 39, 41 S Metering dial ....................................................53
Wi-Fi button (playback mode) .........................97 T Front command dial ..................26, 46, 47, 49, 91
D Shutter speed dial................................. 47, 48, 49 U ON/OFF switch .................................................17
E Dial lock release .................................... 47, 49, 50 V Movie-record button.........................................31
F Hot shoe ...........................................................36 W Hot shoe cover ..................................................36
G Microphone ......................................................31 X Microphone/remote release connector ....... 32, 66
H Diopter adjustment control...............................20 Y HDMI mini connector ......................................108
I Sensitivity dial ..................................................50 Z Micro USB connector............................... 101, 103
J DRIVE dial .................................54, 56, 57, 58, 59 a b (delete) button ............................................30
K Strap eyelet ......................................................10 b a (playback) button ......................................26
L Sync terminal....................................................36 c Electronic viewfinder (EVF) ........................... 5, 19
M Connector cover .........................66, 101, 103, 108 d VIEW MODE button .........................................19
N Focus mode selector .........................................61 e AE-L (exposure lock) button ...................... 67, 81
O Lens signal contacts ............................................7 f Rear command dial......................8, 28, 34, 62, 91
P Lens release button ..........................................12 g AF-L (focus lock) button ....................... 61, 67, 81
Q Fn1 button (function button 1) .................. 39, 40 h Indicator lamp ....................................................4
Control Lock
To prevent accidental operation of the selector and Q buttons during shooting, press MENU/OK until X is displayed. The controls can be unlocked by pressing MENU/OK until X is no longer displayed.
3
Parts of the Camera
The Selector
Press the selector up (w), right (r), down (t), or left (e) to highlight items and
press MENU/OK (q) to select. The up, left, right, and down buttons also double
as the Fn3, Fn4, Fn5, and Fn6 buttons, respectively (P 39, 41, 42, 43, 45).
The Indicator Lamp
When the viewfinder is not in use (P 19), the indicator lamp shows camera status.
Indicator lamp
Glows green
Blinks green
Blinks green and orange
Glows orange
Blinks orange
Blinks red
Camera status
Focus locked.
Blur, focus, or exposure warning. Picture can be taken.
Recording pictures. Additional pictures can be taken.
Recording pictures. No additional pictures can be taken at this time.
Flash charging; flash will not fire when picture is taken.
Lens or memory error.
R Warnings may also appear in the display (P 122).
4
Indicator lamp
Parts of the Camera
■ Shooting: LCD Monitor/Viewfinder
LCD monitor
Viewfinder
100
+1
100
F
100
+1
+1
F
Before You Begin
Camera Displays
The following types of indicator may be displayed during shooting and playback. In the description that
follows, all available indicators are shown for illustrative purposes; the indicators actually displayed vary
with camera settings. Note that the LCD monitor and electronic viewfinder have different aspect ratios.
3
2
1
0
1
2
3
0.1 0.5
P
1.0
2000
1.5
2.0
F5.6
3.0
5.0
10
200
A Flash mode .......................................................36
B Microphone/remote release ................. 32, 66, 82
C Flash compensation ..........................................81
D Macro (close-up) mode.....................................41
E Self-timer indicator ..........................................35
F Continuous mode .............................................56
G White balance...................................................43
H Film simulation.................................................42
I Dynamic range .................................................79
J Focus frame ......................................................67
K Number of available frames............................125
0.1 0.5
P
L Image quality and size ......................................79
M Temperature warning .....................................124
N Control lock.........................................................3
O Blur warning....................................... 4, 119, 122
P IS mode ............................................................82
Q Location data download status
R Focus warning .................................... 4, 119, 122
S Silent mode indicator .......................................89
T Distance indicator .............................................61
U Battery level .....................................................17
V Sensitivity.........................................................50
2000
1.0
F5.6
1.5
2.0
F5.6
3.0
5.0
10
200
W Aperture ............................................... 46, 48, 49
X Shutter speed ....................................... 46, 47, 49
Y Metering...........................................................53
Z Shooting mode .................................................46
a Focus indicator..................................................62
b Exposure compensation/
exposure indicator ...................................... 49, 52
c Histogram.........................................................23
d Virtual horizon ..................................................22
e Depth-of-field preview .....................................48
5
Parts of the Camera
■ Shooting: LCD Monitor
000100
+1
3
2
1
F
0
1
2
3
P 1
2000
5.6
F
200
A Self-timer indicator ..........................................35 M Battery level .....................................................17
B Flash mode .......................................................36 N Sensitivity.........................................................50
Flash compensation ..........................................81 O Aperture ............................................... 46, 48, 49
C Macro (close-up) mode.....................................41 P Focus frame/focus point ...................................45
D Metering...........................................................53 Q Shutter speed ....................................... 46, 47, 49
E Continuous mode .............................................56 R Shooting mode .................................................46
F Silent mode indicator .......................................89 S Control lock.........................................................3
G Number of available frames............................125 T Focus mode ......................................................61
H Temperature warning .....................................124 U Exposure compensation/
exposure indicator ...................................... 49, 52
I Image quality and size ......................................79
J Dynamic range .................................................79
K Film simulation.................................................42
L White balance...................................................43
■ Playback: Viewfinder/LCD Monitor
100-0001
3:2 F
YouTube
12 / 31 / 2050
1 / 1000
6
10 : 00 AM
F5.6
+1/ 3
200
A Rating ...............................................................26
B Intelligent face detection indicator ...................38
C Red-eye removal indicator................................85
D Advanced filter .................................................58
E Silent mode indicator .......................................89
F Gift image.........................................................26
G Frame number ..................................................93
H Playback mode indicator...................................26
I Mark for upload to ............................................86
J Photobook assist indicator ................................75
K DPOF print indicator .......................................105
L Protected image ...............................................84
Lenses
The camera can be used with lenses for the FUJIFILM X-mount.
Parts of the Lens
Before You Begin
Removing the Caps
Remove the caps as shown.
Q Lens caps may differ from those shown.
A Lens hood
B Mounting marks
C Focus ring
D Zoom ring
E Aperture ring
F O.I.S. switch
G Aperture mode switch
H Lens signal contacts
I Front lens cap
J Rear lens cap
Attaching the Hood
When attached, lens hoods reduce glare and protect the front lens element.
7
Lenses
Lenses with Aperture Rings
At settings other than A, you
can adjust aperture by rotating
the lens aperture ring (exposure modes A and M).
Aperture ring
A 16 11 8 5.6 4 2.8
A 16 11 8 5.6 4
Lenses with No Aperture Rings
The method used to adjust aperture can be selected using the e APERTURE SETTING option
(P 82) in the shooting menu. When an option other
than AUTO is selected, aperture can be adjusted
using the rear command dial.
The Aperture Mode Switch
If the lens has an aperture mode switch, aperture can
be adjusted manually by sliding the switch to Z and
rotating the aperture ring.
Aperture ring
R Aperture control defaults to the rear command dial,
but can be reassigned to the front command dial
using the e COMMAND DIAL SETTING option in
the setup menu.
Aperture mode switch
8
Lenses
O.I.S. switch
Manual Focus Lenses
Slide the focus ring to the front for
autofocus.
For manual focus, slide the focus ring
to the back and rotate it while checking the results in the camera display.
The focus distance and depth-of-field
indicators can be used to assist manual
focus. Note that manual focus may not
be available in all shooting modes.
Before You Begin
Lenses with O.I.S. Switches
If the lens supports optical image stabilization
(O.I.S.), the image stabilization mode can be chosen in the camera menus. To activate image stabilization, slide the O.I.S. switch to ON.
The Depth-of-Field Indicator
The depth-of-field indicator shows the approximate
depth of field (the distance in front of and behind the
focus point that appears to be in focus).
Distance
indicator
Q The camera does not display the focus distance when
the lens is in manual focus mode.
9
First Steps
Attaching the Strap
Attach the strap clips to the camera and then attach the strap.
1 Open a strap clip.
Use the clip attaching tool to open a strap clip,
making sure that the tool and clip are in the
orientations shown.
3 Pass the clip through the eyelet.
Rotate the clip fully through
the eyelet until it clicks
closed.
4 Attach a protective cover.
Q Keep the tool in a safe place. You will need it to
open the strap clips when removing the strap.
2 Place the strap clip on an eyelet.
Hook the strap eyelet in the clip opening. Remove the tool, using the other hand to keep
the clip in place.
10
Place a protective cover over the eyelet as
shown, with the black side of the cover toward
the camera. Repeat Steps 1–4 for the second
eyelet.
Attaching the Strap
5 Insert the strap.
Insert the strap through a protective cover
and strap clip.
6 Fasten the strap.
Fasten the strap as shown. Repeat Steps 5–6
for the second eyelet.
First Steps
Q To avoid dropping the camera, be sure the strap is
correctly secured.
11
Attaching a Lens
Lenses attach as described below.
Q Care is required to prevent dust entering the camera while attaching and removing lenses.
1 Remove the body and rear caps.
Remove the body cap from the camera and
the rear cap from the lens.
Removing Lenses
To remove the lens, turn the
camera off, then press the lens
release button and rotate the
lens as shown.
Lens release button
Q Do not touch the camera’s internal parts.
2 Attach the lens.
Place the lens on mount, keeping the marks
on the lens and camera aligned, and then rotate the lens until it clicks into place.
Q Do not press the lens release button while attaching the lens.
12
Q To prevent dust accumulating on the lens or inside the
camera, replace the lens caps and camera body cap
when the lens is not attached.
Lenses and Other Optional Accessories
The camera can be used with lenses for the FUJIFILM
X-mount and the other accessories listed from page
109.
Charging the Battery
The battery is not charged at shipment. Before use, charge the battery in the supplied battery charger.
1 Place the battery in the charger.
Place the battery in the supplied battery charger as shown.
Charge lamp
Plug the charger into an indoor power outlet.
The charging indicator will light.
The Charging Indicator
The charging indicator shows battery charge status as follows:
Charging
indicator
Arrow
On
Battery not
inserted.
Battery fully
charged.
Battery charging.
Blinks
Battery fault.
Off
Battery
The camera uses an NP-W126 rechargeable battery.
R The supplied AC cord is for use exclusively with
the supplied battery charger. Do not use the
supplied charger with other cords or the supplied cord with other devices.
Battery status
Action
First Steps
Battery charger
2 Plug the charger in.
Insert the battery.
Remove the battery.
—
Unplug the charger
and remove the
battery.
3 Charge the battery.
Remove the battery when charging is complete. See the specifications (P 129) for charging times (note that charging times increase
at low temperatures).
Q Unplug the charger when it is not in use.
13
Inserting the Battery
After charging the battery, insert the battery as described below.
1 Open the battery-chamber cover.
Slide the battery-chamber latch as shown and
open the battery-chamber cover.
2 Insert the battery.
Using the battery to keep the battery latch
pressed to one side, insert the battery contacts first in the direction shown by the arrow.
Confirm that the battery is securely latched.
Arrow
Q Do not open the battery-chamber cover when
the camera is on. Failure to observe this precaution could damage image files or memory cards.
Q Do not use excessive force when handling the
battery-chamber cover.
Removing the Battery
Before removing the battery,
turn the camera off and open
the battery-chamber cover.
Press the battery latch to the
side, and slide the battery out Battery latch
of the camera as shown.
14
Battery latch
Q Insert the battery in the orientation shown. Do
not use force or attempt to insert the battery upside down or backwards. The battery will slide in
easily in the correct orientation.
3 Close the battery-chamber cover.
Inserting a Memory Card
The camera has no internal memory; instead, pictures are stored on optional SD, SDHC, and SDXC
memory cards (sold separately). Memory cards are inserted as described below.
1 Open the memory card slot cover.
3 Close the memory card slot cover.
Turn the camera off and open the memory
card slot cover.
First Steps
2 Insert the memory card.
Holding the memory card in the orientation
shown, slide it in until it clicks into place at the
back of the slot.
Click!
Removing the Memory Card
Before removing the memory
card, turn the camera off and
open the memory card slot
cover. Press the card in and
release it slowly. The card can
then be removed by hand.
When a memory card is removed, the card could be ejected too quickly. Use
your finger to hold it and gently release the card.
Q Be sure card is in the correct orientation; do not
insert at an angle or use force.
15
Inserting a Memory Card
■ Compatible Memory Cards
FUJIFILM and SanDisk SD, SDHC, and SDXC memory cards have been approved for use in the camera. A complete list of approved memory cards is available at http://www.fujifilm.com/support/digital_
cameras/compatibility/. Operation is not guaranteed with other cards. The camera can not be used
with xD-Picture Cards or MultiMediaCard (MMC) devices.
Q Memory Cards
• Do not turn the camera off or remove the memory card while the memory card is being formatted or data are
being recorded to or deleted from the card. Failure to observe this precaution could damage the card.
• SD/SDHC/SDXC memory cards can be locked, making it impossible to format the card
or to record or delete images. Before inserting a memory card, slide the write-protect
switch to the unlocked position.
Write-protect switch
• Format memory cards before first use, and be sure to reformat all memory cards after using them in a computer
or other device. For more information on formatting memory cards, see page 94.
• Memory cards are small and can be swallowed; keep out of reach of children. If a child swallows a memory card,
seek medical assistance immediately.
• miniSD or microSD adapters that are larger or smaller than the standard dimensions of an SD/SDHC/SDXC card
may not eject normally; if the card does not eject, take the camera to an authorized service representative. Do
not forcibly remove the card.
• Do not affix labels to memory cards. Peeling labels can cause camera malfunction.
• Movie recording may be interrupted with some types of SD/SDHC/SDXC memory card. Use a H card or
better for movies and burst photography.
• Formatting a memory card in the camera creates a folder in which pictures are stored. Do not rename or delete
this folder or use a computer or other device to edit, delete, or rename image files. Always use the camera to
delete pictures; before editing or renaming files, copy them to a computer and edit or rename the copies, not
the originals. Renaming the files on the camera can cause problems during playback.
16
Turning the Camera on and Off
Rotate the ON/OFF switch to ON to turn the camera on. Select OFF
to turn the camera off.
Q Fingerprints and other marks on the lens or viewfinder can affect pictures or the view through the viewfinder.
Keep the lens and viewfinder clean.
First Steps
R Press the a button to start playback. Press the shutter button halfway to return to shooting mode.
R The camera will turn off automatically if no operations are performed
for the length of time selected for Z POWER MANAGEMENT >
AUTO POWER OFF (P 92). To reactivate the camera after it has turned off automatically, press the shutter button halfway or turn the ON/OFF switch to OFF and then back to ON.
R For information on startup options, see page 92.
Battery Level
After turning the camera on, check the battery level in the display.
Indicator
D (white)
C (white)
B (red)
A (blinks red)
Description
Battery partially discharged.
Battery more than half discharged
Low battery. Charge as soon as possible.
Battery exhausted. Turn camera off and recharge battery.
P
17
Basic Setup
A language-selection dialog is displayed the first time the camera is turned on. Set up the camera as
described below (you can reset the clock or change languages at any time using the F DATE/TIME
or Q a options in the setup menu; for information on displaying the setup menu, see page 89).
1 Choose a language.
Highlight a language and press MENU/OK.
START MENU
ENGLISH
R Press DISP/BACK to skip the current step. Any steps you skip will be displayed the next time the camera is turned on.
FRANCAIS
DEUTSCH
SET
NO
2 Set the date and time.
DATE/TIME NOT SET
2016
2015
YY. MM. DD
2014
2013
2012
SET
NO
1. 1 12 : 00
AM
Press the selector left or right to highlight the year, month, day, hour,
or minute and press up or down to change. To change the order in
which the year, month, and day are displayed, highlight the date format and press the selector up or down. Press MENU/OK to exit to shooting mode when settings are complete.
R If the battery is removed for an extended period, the camera clock will be reset and the language-selection
dialog will be displayed when the camera is turned on.
18
Display Settings
The camera is equipped with an electronic viewfinder (EVF) and an LCD monitor (LCD).
Choosing a Display
Press the VIEW MODE button to cycle through displays as shown
below.
First Steps
EVF
E EYE SENSOR:
SENSOR Automatic display
selection using eye sensor
EVF
EVF ONLY: Viewfinder only
LCD
EVF
EVF ONLY + E: Viewfinder only; eye
sensor turns display on or off
LCD ONLY: LCD monitor only
LCD
The Eye Sensor
The eye sensor turns the viewfinder on when you put your eye to the viewfinder and turns
it off when you take your eye away (note that the eye sensor may respond to objects other
than your eye or to light shining directly on the sensor). If automatic display selection is
enabled, the LCD monitor will turn on when the viewfinder turns off.
Eye sensor
19
Display Settings
The Viewfinder Display
When ON is selected for A SCREEN SET-UP >
EVF AUTOROTATE DISPLAYS in the setup menu
(P 90), the indicators in the viewfinder automatically rotate to match camera orientation.
100
0.1 0.5
P
1.0
2000
1.5
2.0
3.0
5.0
F5.6
F5.6
Focusing the Viewfinder
The camera is equipped with diopter adjustment
in the range –4 to +2 m–1 to accommodate individual differences in vision. Rotate the diopter
adjustment control until the viewfinder display is
in sharp focus.
10
200
Orientation changed from “wide” to “tall”
100
Diopter adjustment control
0.1 0.5
P
2000
1.0
1.5
F5.6
2.0
3.0
5.0
10
200
Q The display in the LCD monitor is unaffected.
20
Adjusting Display Brightness
The brightness of the viewfinder and LCD monitor
can be adjusted using the A SCREEN SET-UP >
EVF/LCD BRIGHTNESS option in the setup menu.
The DISP/BACK Button
The DISP/BACK button controls the display of indicators in the
viewfinder and LCD monitor.
■ LCD Monitor: Shooting
Full
Normal
100
+1
First Steps
■ Viewfinder: Shooting
Info display
Standard
100
+1
000100
3
2
1
F
0
3
1
2
2
1
3
0
1
2
3
0.1 0.5
P
2000
1.0
F5.6
1.5
2.0
F5.6
3.0
5.0
P 1
10
200
P
2000
F5.6
2000
5.6
F
0.1 0.5
200
P
200
100
1.0
2000
1.5
2.0
F5.6
3.0
5.0
10
200
F
3
2
1
0
1
2
3
0.1 0.5
P
1.0
2000
1.5
2.0
3.0
F5.6
Custom
5.0
10
200
Information off
R In addition, a dual display is available in manual focus mode (P 63).
21
The DISP/BACK Button
■ Custom Display
To choose items for display in the viewfinder and for the custom (and in manual focus mode, dual)
display options in the monitor (P 21):
1 Select DISP. CUSTOM SETTING.
Select A SCREEN SET-UP > DISP. CUSTOM SETTING in the setup menu.
2 Choose items.
Highlight items and press MENU/OK to select or deselect.
•
•
•
•
•
Framing grid (P 91)
Virtual horizon (see below)
Focus distance (autofocus)
Focus distance (manual focus)
Histogram
•
•
•
•
•
Exposure (aperture, shutter speed, and sensitivity)
Exposure compensation
Metering
Flash mode
White balance
•
•
•
•
•
Film simulation
Dynamic range
Number of exposures remaining/media
Image quality and size
Battery level
3 Exit.
Press DISP/BACK to exit when settings are complete.
R See page 5 for the locations of these items in the displays.
Virtual Horizon
Selecting ELECTRONIC LEVEL displays a virtual horizon. The camera is level when the two
lines overlap.
R The virtual horizon may not be displayed if the camera lens is pointed up or down.
P
22
The DISP/BACK Button
■ Viewfinder/LCD Monitor: Playback
Information on
Information off
Favorites
3:2 F
12 / 31 / 2050
3
10 : 00 AM
F4.5
-1 2/ 3
12 / 31 / 2050
200
10 : 00 AM
Histograms
Histograms show the distribution of tones in the image. Brightness is shown by the horizontal axis, the
number of pixels by the vertical axis.
Shadows
Highlights
100-0001
3:2 F
ISO 200
1/1000
F4.5
:
: OFF
:
: -1 2/ 3
12 / 31 / 2050
10 : 00 AM
First Steps
1 / 1000
Detail information
100-0001
100-0001
Optimal exposure: Pixels are distributed in an even curve throughout the tone range.
Overexposed: Pixels are clustered
on the right side of the graph.
No. of pixels
Pixel brightness
Detailed Information
A Dynamic range
D Shutter speed/aperture
G White balance
I Frame number
K Histogram
Underexposed: Pixels are clustered
on the left side of the graph.
B Image size and quality
C Sensitivity
E Film simulation
F Flash mode
H Exposure compensation
J Picture (overexposed areas blink on and off )
100-0001
3:2 F
ISO 200
1/1000
F4.5
:
: OFF
:
: -1 2/ 3
12 / 31 / 2050
10 : 00 AM
23
Basic Photography and Playback
Taking Photographs
This section describes how to take pictures using program AE (mode P). For information on S, A, and
M modes, see page 46.
1 Adjust settings for program AE.
A
B
C
F
A Shutter speed (P 46): Select A (auto)
B Sensitivity (P 50): Select A (auto)
C Drive mode (P 54): Select S (single frame)
D Focus mode (P 61): Select S (single AF)
E Aperture (P 46): Select A (auto)
F Metering (P 53): Select o (multi)
Confirm that P appears in
the display.
3
2
1
0
R Image stabilization (P 9) is
recommended.
E
D
24
1
2
3
P
2000
F5.6
200
The Q Button
The Q button can be used to view and adjust
camera settings (P 34).
Taking Photographs
2 Ready the camera.
4 Focus.
Hold the camera steady
with both hands and brace
your elbows against your
sides. Shaking or unsteady
hands can blur your shots.
Frame the picture with your subject in the center of the display and
press the shutter button halfway to
focus.
R If the subject is poorly lit, the AF-assist illuminator may light (P 78).
If the camera is able to focus, it will beep twice
and focus area and focus indicator will glow
green. Focus and exposure will lock while the
shutter button is pressed halfway.
3 Frame the picture.
Lenses with Zoom Rings
Use the zoom ring to frame
the picture in the display.
Zoom
ring
A
If the camera is unable to focus, the focus frame
will turn red, s will be displayed, and the focus indicator will blink white. If the subject is
close to the camera (the actual distance varies with the lens; for more information, see
the lens manual), select macro mode and try
again (P41).
Basic Photography and Playback
To prevent pictures that
are out of focus or too dark
(underexposed), keep your
fingers and other objects
away from the lens, flash,
and AF-assist illuminator.
5 Shoot.
Smoothly press the shutter button
the rest of the way down to take the
picture.
25
Viewing Pictures
Viewing Pictures Full Frame
Pictures can be viewed in the viewfinder or LCD monitor. When taking important pictures, take a test
shot and check the results.
To view pictures full frame, press a.
100-0001
1 / 1000
F4.
F4.5
4.5
2
3
Additional pictures can be viewed by pressing the selector left or right or rotating the front
command dial. Press the selector or rotate the dial right to view pictures in the order recorded, left to view pictures in reverse order. Keep the selector pressed to scroll rapidly to
the desired frame.
R Pictures taken using other cameras are indicated by a m (“gift image”) icon during playback.
Favorites: Rating Pictures
To rate the current picture, press DISP/BACK and press the selector up and down to select from zero to five stars.
26
Viewing Pictures
Viewing Photo Information
The photo information display changes
each time the selector is pressed up.
100-0001
3:2 F
12 / 31 / 2050
1 / 1000
10 : 00 AM
F4.5
-1 2/ 3
: 100
: STD
: STD
: STD
: STD
: STD
: OFF
FILM SIM.
WHITE BALANCE
METERING
EXPOSURE MODE
LENS
FOCAL LENGTH
: PROVIA
: AUTO
: PATTERN
: PROGRAM
: 18.0-55.0mm
F2.8-4.0
: 18.0mm
200
Details, page 1
COLOR SPACE
FACE DETECTION
FLASH MODE
FLASH
Active focus point (“+”)
Details, page 2
: sRGB
:0
: OFF
:0
Details, page 3
R Rotate the front command dial to view other images.
Basic Photography and Playback
Basic data
D-RANGE
COLOR
HIGH LIGHT TONE
SHADOW TONE
SHARPNESS
NOISE REDUCTION
LENS MODULATION OPT.
Zooming in on the Focus Point
Press the FOCUS ASSIST button to
zoom in on the focus point. Press
the button again to return to fullframe playback.
27
Viewing Pictures
Playback Zoom
Rotate the rear command dial right to zoom in on the current picture, left to zoom out (to view multiple images, rotate the dial left when the picture is displayed full frame; P 29). When the picture is
zoomed in, the selector can be used to view areas of the image not currently visible in the display.
Press DISP/BACK or MENU/OK to exit zoom.
Zoom indicator
Navigation window shows
portion of image currently
displayed
R The maximum zoom ratio varies with image size (P 79). Playback zoom is not available with cropped or resized
copies saved at a size of a.
28
Viewing Pictures
Multi-Frame Playback
To change the number of images displayed, rotate the rear command
dial left when a picture is displayed full frame.
100-0001
Rotate right to view
fewer images.
Use the selector to highlight images and press MENU/OK to view the highlighted image full frame (to
zoom in on the selected image, rotate the rear command dial right when the picture is displayed full
frame; P 28). In the nine- and hundred-frame displays, press the selector up or down to view more
pictures.
Basic Photography and Playback
Rotate left to view
more images.
29
Deleting Pictures
To delete individual pictures, multiple selected pictures, or all pictures, press the b button when a
picture is displayed full frame and choose from the options below. Note that deleted pictures can not
be recovered. Copy important pictures to a computer or other storage device before proceeding.
ERASE
FRAME
SELECTED FRAMES
ALL FRAMES
SET
Option
FRAME
SELECTED FRAMES
ALL FRAMES
BACK
Description
Press the selector left or right to scroll through pictures and press MENU/OK to delete the current picture
(a confirmation dialog is not displayed).
Highlight pictures and press MENU/OK to select or deselect (pictures in photobooks or print orders are shown
by S). When the operation is complete, press DISP/BACK to display a confirmation dialog, then highlight OK
and press MENU/OK to delete the selected pictures.
A confirmation dialog will be displayed; highlight OK and press MENU/OK to delete all unprotected pictures.
Pressing DISP/BACK cancels deletion; note that any pictures deleted before the button was pressed can not
be recovered.
R Protected pictures can not be deleted. Remove protection from any pictures you wish to delete (P 84).
R Pictures can also be deleted by A ERASE from playback menu.
R If a message appears stating that the selected images are part of a DPOF print order, press MENU/OK to delete
the pictures.
30
Basic Movie Recording and Playback
Recording High-Definition (HD) Movies
The camera can be used to record short high-definition movies. Sound is recorded in stereo via the
built-in microphone; do not cover the microphone during recording.
1 Press the movie-record button to
start recording.
Recording indicator
12m34s
Time remaining
R During recording, exposure compensation can be
adjusted by up to ±2 EV.
R The indicator lamp lights while movies are being
recorded.
2 Press the button again to end recording. Recording ends automatically when the maximum length is reached or the memory card is
full.
R Zoom can be adjusted while recording is in progress.
R Frame size and rate can be selected using the
W MOVIE SET-UP > MOVIE MODE option (P 82).
Focus mode is selected using the focus mode selector (P 61); for continuous focus adjustment, select C,
or choose S and enable Intelligent Face Detection
(P 78). Intelligent Face Detection is not available in
focus mode M.
Depth of Field
Adjust aperture before recording begins. Choose
low f-numbers to soften background details. The
effect can be heightened by increasing the distance
between your subject and the background.
Basic Movie Recording and Playback
Q The microphone may pick up lens noise and other
sounds made by the camera during recording.
Q Vertical or horizontal streaks may appear in movies
containing very bright subjects. This is normal and
does not indicate a malfunction.
31
Recording High-Definition (HD) Movies
Using an External Microphone
Sound can be recorded with external microphones. See the microphone manual
for details; if the microphone jack is 3.5 mm in diameter, use a 3.5-to-2.5 mm adapter.
R The dialog shown at right will be displayed when a microphone is connected to the microphone/remote release connector. Press MENU/OK and select MIC/REMOTE RELEASE >
m MIC.
CHECK MIC/REMOTE RELEASE
SETTING
SET
SKIP
0.1
0.5
1.0
1000
32
1.5
2.0
F3.3
3.0
5.0 10
400
Viewing Movies
During playback, movies are displayed as shown at right. The following operations
can be performed while a movie is displayed:
100-0006
Operation
Progress is shown in the display during playback.
PLAY
Progress bar
15s
Q Do not cover the speaker during playback.
Q Sound is not played back in silent mode.
STOP
PAUSE
Playback Speed
Press the selector left or right to adjust playback speed during playback. Speed is shown by the Arrow
number of arrows (M or N).
STOP
15s
PAUSE
Basic Movie Recording and Playback
Description
Press the selector down to start playback. Press again to pause. While playback is
Start/pause playback paused, you can press the selector left or right to rewind or advance one frame
at a time.
End playback
Press the selector up to end playback.
Adjust speed
Press the selector left or right to adjust playback speed during playback.
Press MENU/OK to pause playback and display volume controls. Press the selector
up or down to adjust the volume; press MENU/OK again to resume playback. VolAdjust volume
ume can also be adjusted using the b SOUND SET-UP > PLAYBACK VOLUME
option in the playback menu (P 90).
Movie icon
33
The Q (Quick Menu) Button
Press Q for quick access to the following items. For more information on the options available, see the
pages listed below.
AF MODE
BASE
3:2
OFF
SET
A u SELECT CUSTOM SETTING .......................71
B F AF MODE...................................................78
C U DYNAMIC RANGE .....................................79
D D WHITE BALANCE......................................43
E h NOISE REDUCTION ..................................80
F O IMAGE SIZE ..............................................79
G T IMAGE QUALITY .....................................109
H P FILM SIMULATION ...................................42
I r HIGHLIGHT TONE .....................................80
J s SHADOW TONE .........................................80
K f COLOR .....................................................109
L q SHARPNESS..............................................80
M B SELF-TIMER ..............................................35
N b FACE DETECTION ......................................38
O p FLASH MODE ............................................36
P J EVF/LCD BRIGHTNESS .............................90
R h CUSTOM and k COLOR TEMPERATURE white balance options can not be
accessed using the Q button. Use a function button or the shooting menu.
1 Press Q to display the quick menu during shooting.
2 Use the selector to highlight items and rotate the rear command dial to change.
3 Press Q to exit when settings are complete.
34
Using the Q Button
This section describes the shooting options that can be accessed using the Q button.
The Self-Timer
Use the timer for self-portraits or to prevent blur caused by camera shake.
1 Highlight B SELF-TIMER in the
quick menu (P 34) and rotate the
rear command dial to select from
the options below. Press the Q button to proceed.
Option
R Self-timer options can also be accessed from the
shooting menu (P 79).
2 Press the shutter button halfway to
focus.
9
the rest of the way down to
start the timer. The display
in the monitor shows the
number of seconds remaining until the shutter is released. To stop the timer before the
picture is taken, press DISP/BACK.
The self-timer lamp on
the front of the camera
will blink immediately
before the picture is
taken. If the two-second timer is selected,
the self-timer lamp will
blink as the timer counts down.
R The self-timer turns off automatically when the
camera is turned off.
The Q (Quick Menu) Button
Description
The shutter is released two seconds after the
shutter button is pressed. Use to reduce blur
R 2 SEC
caused by the camera moving when the shutter button is pressed.
The shutter is released ten seconds after the
S 10 SEC shutter button is pressed. Use for photographs
in which you wish to appear yourself.
OFF
Self-timer off.
3 Press the shutter button
Q Stand behind the camera when using the shutter button. Standing in front of the lens can interfere with focus and exposure.
35
Using the Q Button
Flash Photography
Use shoe-mounted flash units for additional lighting at night or indoors under low light.
1 Remove the hot shoe cover and slide the flash onto the hot
shoe as shown, stopping when it clicks into place.
Optional Flash Units
The camera can be used with optional FUJIFILM shoemounted flash units (P 112). Do not use third-party flash
units that apply over 300 V to the camera hot shoe.
The Sync Terminal
Use the sync terminal to connect flash units that require a sync cable.
Removing the Flash
Flash units mounted on the hot shoe can be removed by lowering
the flash and pressing the PUSH button while sliding the unit from
the shoe.
2 Raise the flash.
36
Using the Q Button
3 Highlight p FLASH MODE in the quick menu (P 34) and rotate the rear command dial
to select from the options below. Press the Q button to proceed.
R Flash options can also be accessed from the shooting menu (P 81).
Q Depending on the distance to the subject, some lenses may cast shadows in photos taken with the flash.
R Turn off or lower the flash where flash photography is prohibited or to capture natural lighting under dim light.
R If p is displayed when the shutter button is pressed halfway, the flash will fire when the photo is taken.
R Except in commander mode, the flash may fire several times with each shot. Do not move the camera until
shooting is complete.
The Q (Quick Menu) Button
Mode
Description
Q (AUTO FLASH)/
FLASH)/
The flash fires when required. This option is available in program AE (mode P) only.
K (RED EYE REDUCTION) *
N (FORCED FLASH)/
FLASH)/ The flash fires whenever a picture is taken. Use for backlit subjects or for natural colorL (FORCED FLASH) * ation when shooting in bright light.
F (SLOW SYNCHRO)/
SYNCHRO)/ Capture both the main subject and the background under low light (note that brightly
M (RED EYE & SLOW) * lit scenes may be overexposed).
l (2ND CURTAIN SYNC.)/
SYNC.)/
The flash fires immediately before the shutter closes.
d (2ND CURTAIN SYNC.) *
A flash mounted on the hot shoe can be used to control optional remote flash units.
D (COMMANDER)
P (SUPPRESSED FLASH) The flash does not fire even when the subject is poorly lit. A tripod is recommended.
* Red-eye removal is available in these modes when Intelligent Face Detection is active ((P
P 78) and red-eye
removal is on ((P
P 81). Red-eye removal minimizes ““red-eye
red-eye”” caused when light from the flash is reflected from
the subject’s retinas as shown in the illustration at right.
Flash Sync Speed
The flash will synchronize with the shutter at shutter speeds of 1/180 s or slower.
37
Using the Q Button
Intelligent Face Detection
Intelligent Face Detection sets focus and exposure for human faces anywhere in the frame, preventing the camera from focusing on the background in group portraits. Choose for shots that emphasize
portrait subjects.
To use Intelligent Face Detection, highlight b FACE DETECTION in the quick
menu (P 35), then rotate the rear command dial until ON is displayed and press the
Q button. Faces can be detected with the camera in vertical or horizontal orientation; if a face is detected, it will be indicated by a green border. If there is more than
one face in the frame, the camera will select the face closest to the center; other
faces are indicated by white borders.
P
Q In some modes, the camera may set exposure for the frame as a whole rather than the portrait subject.
Q If the subject moves as the shutter button is pressed, their face may not be in the area indicated by the green
border when the picture is taken.
R Intelligent face detection can also be accessed using the G AUTOFOCUS SETTING > FACE DETECTION option in the shooting menu (P 78).
38
The Fn (Function) Buttons
The roles played by the six function buttons can be selected in the setup menu
FUNCTION (Fn) SETTING
Fn1
(P 91) or by pressing and holding the DISP/BACK button and choosing a button
Fn2
from the menu shown at right. The options available include bracketing and
Fn3
Fn4
advanced filters (P 40), macro mode (P 41), depth-of-field preview (P 48),
Fn5
Fn6
auto sensitivity control (P 50), the self-timer (P 35), image size (P 79), image
quality (P 109), dynamic range (P 79), film simulation (P 42), white balance
(P 43), AF mode (P 78), focus-frame selection (P 45), custom settings (P 71), Intelligent Face Detection (P 38), RAW/JPEG toggle (P 69), and aperture setting (P 82) and wireless (P 97) options. The
default options are shown below:
Fn2 button
Fn3 button
Bracketing and advanced filters (P 40)
Wireless options (P 41)
Macro mode (P 41)
Fn4 button
Fn5 button
Fn6 button
Film simulation (P 42)
White balance (P 43)
Focus-frame selection (P 45)
The Fn (Function) Buttons
Fn1 button
R You can also display options for any of the function buttons by pressing and holding the button.
39
Default Roles
The following sections describe the default roles assigned to the Fn buttons.
Bracketing and Advanced Filters (Fn1)
Buttons assigned this role can be used to select bracketing or advanced
filter options.
R Bracketing and advanced filter options can also be accessed from the shooting
menu (P 77).
■ Bracketing
O Exposure (AE) bracketing
W Sensitivity (ISO) bracketing
X Film simulation bracketing
Y Dynamic range bracketing
H White balance bracketing
±1
±2/ 3 ±1/ 3
AE BKT
When the DRIVE dial is rotated to BKT, pressing the button displays bracketing options (P 54). Press the selector up or down to select a bracketing type; if applicable,
you can then press the selector left or right to select a
bracketing amount.
■ Advanced Filters
When the DRIVE dial is rotated to ADV., pressing the button displays advanced filter
options (P 58). Press the selector up or down to select the desired filter.
ADVANCED FILTER
TOY CAMERA
Create shaded borders
as taken by toycameras.
(nostalgic effect)
40
Default Roles
Wireless Options (Fn2)
Press the function button in shooting mode to connect to a smartphone
or tablet via Wi-Fi (P 97). Once a connection is established, you can control the camera from the phone or download location data.
R Wireless options can also be accessed from the shooting and playback menus
(P 82, 83).
Macro Mode (Fn3)
To focus at short distances, press the function button and select ON. To exit macro mode, press the
selector up and select OFF.
MACRO
ON
OFF
The Fn (Function) Buttons
R The distances at which the camera will focus in macro mode vary with the lens. See the lens manual for details.
R Macro mode can also be accessed using the G AUTOFOCUS SETTING > MACRO option in the shooting
menu (P 78).
41
Default Roles
Film Simulation (Fn4)
Simulate the effects of different kinds of film, including black-and-white
(with or without color filters). Press the function button to display the
options shown below, then press the selector up or down to highlight an
option and press MENU/OK to select.
Option
Description
c (PROVIA/STANDARD) Standard color reproduction. Suited to a wide range of subjects, from portraits to landscapes.
A high-contrast palette of saturated colors, suited to nature photos.
> (Velvia/VIVID)
Enhances the range of hues available for skin tones in portraits while preserving the bright blues of daye (ASTIA/SOFT)
light skies. Recommended for outdoor portrait photography.
g (PRO Neg. Hi)
Offers slightly more contrast than h (PRO Neg. Std). Recommended for outdoor portrait photography.
A soft-toned palette. The range of hues available for skin tones is enhanced, making this a good choice for
h (PRO Neg. Std)
studio portrait photography.
Take pictures in standard black and white.
; (MONOCHROME)
e (MONOCHROME + Take black-and-white pictures with slightly increased contrast. This setting also slightly tones down the
brightness of the sky.
Ye FILTER)
d (MONOCHROME + Take black-and-white pictures with increased contrast. This setting also tones down the brightness of the
sky.
R FILTER)
f (MONOCHROME +
Soften skin tones in black-and-white portraits.
G FILTER)
Take pictures in sepia.
f (SEPIA)
R Film simulation options can be combined with tone and sharpness settings (P 80).
R Film simulation options can also be accessed from the shooting menu (P 109).
42
Default Roles
White Balance (Fn5)
For natural colors, press the function button to display the following options, then use the selector to highlight an option that matches the light
source and press MENU/OK. The dialog shown at bottom right will be displayed; use the selector to fine-tune white balance or press DISP/BACK to
exit without fine-tuning.
WB SHIFT
SET
R White balance is adjusted for flash lighting only in AUTO and g modes. Turn the flash off using other white
balance options.
R Results vary with shooting conditions. Play pictures back after shooting to check colors.
R White balance options can also be accessed from the shooting menu (P 80).
The Fn (Function) Buttons
Option
Description
Option
Description
AUTO White balance adjusted automatically.
j For subjects in the shade.
h Measure a value for white balance (P 44).
k Use under “daylight” fluorescent lights.
Selecting this option displays a list of color
l Use under “warm white” fluorescent lights.
temperatures (P 44); highlight a temperam Use under “cool white” fluorescent lights.
k ture and press MENU/OK to select the highn Use under incandescent lighting.
lighted option and display the fine-tuning
Reduces the blue cast typically associated
g
dialog.
with underwater lighting.
i For subjects in direct sunlight.
43
Default Roles
h: Custom White Balance
Choose h to adjust white balance for unusual lighting conditions. White balance measurement options will
be displayed; frame a white object so that it fills the display and press the shutter button all the way down to
measure white balance (to select the most recent custom value and exit without measuring white balance,
press DISP/BACK, or press MENU/OK to select the most recent value and display the fine-tuning dialog).
• If “COMPLETED!” is displayed, press MENU/OK to set white balance to the measured value.
• If “UNDER” is displayed, raise exposure compensation (P 52) and try again.
• If “OVER” is displayed, lower exposure compensation (P 52) and try again.
k: Color Temperature
Color temperature is an objective measure of the color of a light source, expressed in Kelvin (K). Light sources
with a color temperature close to that of direct sunlight appear white; light sources with a lower color temperature have a yellow or red cast, while those with a higher color temperature are tinged with blue. You can match
color temperature to the light source as shown in the following table, or choose options that differ sharply from
the color of the light source to make pictures “warmer” or “colder.”
Choose for redder light sources
or “colder” pictures
2,000 K
Candlelight
Sunset/sunrise
44
Choose for bluer light sources
or “warmer” pictures
5,000 K
Direct sunlight
15,000 K
Blue sky
Shade
Default Roles
Focus-Frame Selection (Fn6)
The camera offers a choice of focus points, allowing photographs
to be composed with the main subject positioned almost anywhere in the frame.
Q In focus modes S and C, focus-area selection is only available when
t AREA is selected for G AUTOFOCUS SETTING > AF MODE in
the shooting menu and Intelligent Face Detection (P 38) is off.
To position the focus frame, press the function button and then
press the selector up, down, left, or right (the focus frame can be
returned to the center by pressing DISP/BACK). Press MENU/OK to
put the setting into effect. In manual focus mode, you can also
select the focus point using the function button.
Focus point
Focus frame
R Focus-area selection can also be accessed using the G AUTOFOCUS SETTING option in the shooting menu
(P 78).
The Fn (Function) Buttons
In focus modes S and C, you can choose the size of the focus
frame by pressing the function button and rotating the rear
command dial. Rotate the dial left to reduce the frame by up to
50%, right to enlarge it by up to 150%, or press the FOCUS ASSIST
button to restore the frame to its original size. Press MENU/OK to
put the setting into effect.
45
More on Photography and Playback
Choosing an Exposure Mode
The camera offers a choice of program AE (P), shutter-priority AE (S), aperture-priority AE (A), and
manual exposure (M) modes.
Program AE (P)
To allow the camera to adjust both shutter speed and aperture for optimal exposure, set shutter speed and aperture to A. P will appear in the
display.
Q If the subject is outside the metering range of the camera, the shutter speed
and aperture displays will show “– – –”.
Aperture mode switch
3
2
1
0
1
2
3
P
Program Shift
If desired, you can rotate the front command dial to select other combinations of
shutter speed and aperture without altering exposure (program shift). The new
values for shutter speed and aperture are shown in yellow. Program shift is not
available if the attached flash supports TTL auto, AUTO is selected for U DYNAMIC RANGE in the shooting menu (P 79), or the sensitivity dial is rotated to A (P 50).
To cancel program shift, turn the camera off.
F5.6
200
3
2
1
0
Shutter speed
1
2
3
P
46
2000
2000
F5.6
200
Aperture
Choosing an Exposure Mode
R At settings other than 180X, shutter speed can also be adjusted in increments
of 1/3 EV by rotating the front command dial. Shutter speed can be adjusted
even while the shutter button is pressed halfway.
Aperture mode switch
3
Q If the correct exposure can not be achieved at the selected shutter speed,
aperture will be displayed in red when the shutter button is pressed halfway.
Adjust shutter speed until the correct exposure is achieved.
2000
S
Q If the subject is outside the metering range of the camera, the aperture display will show “– – –”.
2
1
0
1
2
3
200
More on Photography and Playback
Shutter-Priority AE (S)
To adjust shutter speed manually while letting the camera select aperture for optimal exposure, set aperture to A and use the shutter speed
dial (if A is currently selected for shutter speed, press the dial lock release
while rotating the shutter speed dial). S will appear in the display.
Sensitivity and Depth of Field
If you choose a fast shutter speed when the subject is poorly lit, the camera autoexposure program will select a wider aperture. This will produce the correct
exposure but may also reduce depth of field so that less of the area behind and
in front of your subject appears to be in focus (see the top illustration at right).
To stop aperture down and increase depth of field as shown in the second of
the two illustrations at right, select a higher sensitivity.
47
Choosing an Exposure Mode
Aperture-Priority AE (A)
To adjust aperture manually while letting the camera select shutter
speed for optimal exposure, rotate the shutter speed dial to A and adjust
aperture as desired. A will appear in the display.
R Aperture can be adjusted even while the shutter button is pressed halfway.
Q If the correct exposure can not be achieved at the selected aperture, the
shutter speed will be displayed in red when the shutter button is pressed
halfway. Adjust aperture until the correct exposure is achieved.
Q If the subject is outside the metering range of the camera, the shutter speed
display will show “– – –”.
Aperture mode switch
3
2
1
0
1
2
3
A
Previewing Depth of Field
When L PREVIEW DEPTH OF FIELD is assigned to a function button (P 39),
pressing the button stops aperture down to the selected setting, allowing
depth of field to be previewed in the display.
3
2
1
0
1
2
3
Sensitivity and Motion Blur
If you choose a narrow aperture when the subject is poorly lit, the shutter
speed selected by the autoexposure program may not be fast enough to prevent motion blur (see the top illustration at right). For faster shutter speeds
that reduce motion blur as shown in the second of the two illustrations at right,
select a higher sensitivity.
48
F5.6
200
Choosing an Exposure Mode
R At settings other than 180X, shutter speed can also be adjusted in increments
Aperture mode switch
of 1/3 EV by rotating the front command dial.
R The manual exposure display includes an exposure indicator that shows the Exposure indicator
amount the picture would be under- or over-exposed at current settings.
3
2
1
0
1
2
3
M
2000
F5.6
More on Photography and Playback
Manual Exposure (M)
Exposure can be altered from the value suggested by the camera by
setting both shutter speed and aperture to values other than A (if A is
currently selected for shutter speed, press the dial lock release while rotating the shutter speed dial). M will appear in the display.
200
Exposure Preview
To preview exposure in the LCD monitor, select ON for A SCREEN
SET-UP > PREVIEW EXP. IN MANUAL MODE. Select OFF when
using the flash or on other occasions on which exposure may
change when the picture is taken.
49
Sensitivity
“Sensitivity” refers to the camera’s sensitivity to light. Sensitivity is adjusted by pressing the dial lock release and rotating the sensitivity dial;
choose from values between 200 and 6400, or select L (100), H1 (defaults
to 12800), or H2 (defaults to 25600) for special situations. Higher values
can be used to reduce blur when lighting is poor, while lower values allow slower shutter speeds or wider apertures in bright light; note, however, that mottling may appear in pictures taken at high sensitivities, particularly at H2, while choosing
L reduces dynamic range. Values of from ISO 200 to ISO 6400 are recommended in most situations. If
A (auto) is selected, the camera will adjust sensitivity automatically in response to shooting conditions.
R RAW images can not be recorded at settings of L, H1, or H2. Only JPEG images will be recorded if these settings
are chosen when RAW, FINE+RAW, or NORMAL+RAW is selected for image quality (P 79).
R The N ISO DIAL SETTING option in the setup menu can be used to choose the sensitivity assigned to the H1
and H2 positions on the sensitivity dial (P 91). Choose from 12800, 25600, and 51200.
50
Sensitivity
N ISO AUTO SETTING
Option
Default
DEFAULT SENSITIVITY
200
MAX. SENSITIVITY
800
MIN. SHUTTER SPEED
1/60
R If the value selected for DEFAULT SENSITIVITY is higher than that selected for MAX. SENSITIVITY, DEFAULT
SENSITIVITY will be set to the value selected for MAX. SENSITIVITY.
R The camera may select shutter speeds slower than MIN. SHUTTER SPEED if pictures would still be underexposed at the value selected for MAX. SENSITIVITY.
More on Photography and Playback
■ A (Auto)
The N ISO AUTO SETTING item in the shooting menu (P 78) controls
how the camera adjusts sensitivity when A is selected. The camera automatically chooses a sensitivity between the default and maximum values; sensitivity is only raised above the default value if the shutter speed
required for optimal exposure would be slower than the value selected
for MIN. SHUTTER SPEED.
51
Exposure Compensation
Rotate the exposure compensation dial to adjust exposure when photographing very bright, very dark, or high-contrast subjects. The effect
is visible in the display.
Exposure compensation indicator
100
+1
3
2
1
0
1
2
3
P
2000
F5.6
0.1 0.5
200
LCD monitor
P
2000
1.0
1.5
2.0
3.0
5.0
F5.6
10
200
Viewfinder
Choose positive values (+) to
increase exposure
Exposure Value (EV)
The exposure value is determined by sensitivity and
by aperture and shutter speed, which control the
amount of light to which the sensor is exposed. Doubling either the sensitivity or the amount of light increases EV by one, while halving it reduces EV by one.
Choosing an Exposure Compensation Value
• Backlit subjects: Choose values
from +2/3 EV to +12/3 EV.
• Highly reflective subjects or very
bright scenes (e.g., snowfields): +1 EV
Choose negative values (–) to
reduce exposure
Q The amount of compensation available varies with
the shooting mode.
52
• Scenes that are mostly sky: +1 EV
• Spotlit subjects (particularly if photographed against dark backgrounds): –2/3 EV
• Subjects with low reflectivity (pine trees or dark-colored foliage):
–2/3 EV
Metering
Mode
o
(MULTI)
Description
The camera instantly determines exposure based on an analysis of composition, color, and brightness distribution. Recommended in most situations.
The camera meters lighting conditions in an area at the center of the frame
equivalent to 2% of the total. Recommended with backlit subjects and in other
p
(SPOT) cases in which the background is much brighter or darker than the main subject.
Exposure is set to the average for the entire frame. Provides consistent expoq
sure across multiple shots with the same lighting, and is particularly effective for
(AVERAGE)
landscapes and portraits of subjects dressed in black or white.
Q The selected option will only take effect when Intelligent Face Detection is off (P 38).
More on Photography and Playback
To choose how the camera meters exposure, rotate the metering dial to
select from the following options.
53
The DRIVE Dial
The DRIVE dial gives you access to the following options.
Option
BKT
CH
CL
S
j
ADV.
u
Description
Bracketing: Automatically vary settings over a series of pictures (P 54).
High-speed burst: Shoot photos in high-speed bursts (P 56).
Low-speed burst: Shoot in low-speed bursts (P 56).
Single frame: Take photos one at a time.
Multiple exposure: Create photos that combine two exposures (P 57).
Advanced filter: Take photos with filter effects (P 58).
Panorama: Follow an on-screen guide to create panoramas (P 59).
Bracketing
Automatically vary settings over a series of pictures.
1 Rotate the DRIVE dial to BKT.
54
The DRIVE Dial
program selection is assigned to the Fn1 button) or the shooting menu (P 77).
Option
Description
Select a bracketing amount. Each time the shutter button is pressed, the camera will take three shots:
one using the metered value for exposure, the second overexposed by the selected amount, and the third
AE BKT
underexposed by the same amount (regardless of the amount selected, exposure will not exceed the limits
of the exposure metering system).
Select a bracketing amount. Each time the shutter is released, the camera will take a picture at the current
sensitivity (P 50) and process it to create two additional copies, one with sensitivity raised and the other
ISO BKT
with sensitivity lowered by the selected amount (regardless of the amount selected, sensitivity will not
exceed ISO 6400 or fall below ISO 200).
FILM SIMULATION Select a bracketing type. Each time the shutter is released, the camera takes one shot and processes it to
BKT
create copies with the selected film simulation settings (P 42).
Each time the shutter button is pressed, the camera takes three shots with different dynamic ranges (P 79):
DYNAMIC RANGE 100% for the first, 200% for the second, and 400% for the third. While dynamic range bracketing is in effect,
BKT
sensitivity will be restricted to a minimum of ISO 800; the sensitivity previously in effect is restored when
bracketing ends.
Select a bracketing amount. Each time the shutter button is pressed, the camera takes three shots: one at
WHITE BALANCE
the current white balanced setting, one with fine-tuning increased by the selected amount, and another
BKT
with fine-tuning decreased by the selected amount.
More on Photography and Playback
2 Select one of the following options using a function button (P 40; at default settings, bracketing
3 Take photographs.
55
The DRIVE Dial
Continuous Shooting (Burst Mode)
Capture motion in a series of pictures.
1 Rotate the DRIVE dial to select CH (high-speed
burst) or CL (low-speed burst).
R Additional time may be required to record pictures
when shooting ends.
R If file numbering reaches 999 before shooting is
complete, the remaining pictures will be recorded
to a new folder (P 93).
R In some drive modes, shooting may not begin if the
space available on the memory card is insufficient.
Focus and Exposure
To vary focus and exposure with each shot, select focus mode C; in other modes, focus and exposure are
determined by the first shot in each series.
2 Take photographs. The camera will take pictures while the shutter button is pressed;
shooting ends when the shutter button is released, the maximum number of pictures has
been taken, or the memory card is full.
R Frame rate varies with the subject, shutter speed,
sensitivity, and focus mode and may slow as more
shots are taken.
R The flash turns off automatically; the previously-selected flash mode is restored when burst shooting
is disabled.
56
Q When CH is selected, the camera
focuses using the focus frames
shown at right.
Q Focus tracking performance varies with aperture, sensitivity, and
shooting conditions.
1000
F3.3
CH mode focus frames
The DRIVE Dial
+
1 Rotate the DRIVE
dial to j.
4 Take the second shot, using the first frame as a
guide.
5 Press MENU/OK to create the multiple exposure,
or press the selector left to return to Step 4
and retake the second shot.
More on Photography and Playback
Multiple Exposures
Create a photograph that combines two exposures.
2 Take the first shot.
3 Press MENU/OK. The first shot will be shown superimposed on the view through the lens and
you will be prompted to take the second shot.
R To return to Step 2 and retake the first shot,
press the selector left. To save the first shot and
exit without creating a multiple exposure, press
DISP/BACK.
57
The DRIVE Dial
Advanced Filters
Take photos with filter effects.
1 Rotate the DRIVE
Filter
dial to ADV..
K DYNAMIC TONE
X SOFT FOCUS
2 Select one of the following options using a
function button (P 40; at default settings, filter
selection is assigned to the Fn1 button) or the
shooting menu (P 77).
Filter
G TOY CAMERA
H MINIATURE
I POP COLOR
J HIGH-KEY
Z LOW-KEY
58
Description
Choose for a retro toy camera
effect.
The tops and bottoms of pictures are blurred for a diorama
effect.
Create high-contrast images
with saturated colors.
Create bright, low-contrast
images.
Create uniformly dark tones
with few areas of emphasized
highlights.
u PARTIAL COLOR (RED)
v PARTIAL COLOR (ORANGE)
w PARTIAL COLOR (YELLOW)
x PARTIAL COLOR (GREEN)
y PARTIAL COLOR (BLUE)
z PARTIAL COLOR (PURPLE)
Description
Dynamic tone expression is
used for a fantasy effect.
Create a look that is evenly
soft throughout the whole
image.
Areas of the image that are
the selected color are recorded in that color. All other areas
of the image are recorded in
black-and-white.
3 Take photographs.
R Depending on the subject and camera settings, images may in some cases be grainy or vary in brightness and hue.
The DRIVE Dial
1 Rotate the DRIVE
dial to u.
2 To select the size of the angle through which
you will pan the camera while shooting, press
the selector left. Highlight a size and press
MENU/OK.
3 Press the selector right to view a choice of pan
directions. Highlight a pan direction and press
MENU/OK.
4 Press the shutter button all the way down to
start recording. There is no need to keep the
shutter button pressed during recording.
5 Pan the camera in the direction shown by the
arrow. Shooting ends automatically when the
camera is panned to the end of the guides
and the panorama is complete.
ANGLE
DIRECTION
R Shooting ends if the shutter button is pressed all
the way down during shooting. No panorama
may be recorded if the shutter button is pressed
before the panorama is complete.
More on Photography and Playback
Panoramas
Follow an on-screen guide to create a panorama.
For Best Results
For best results, use a lens with a focal length of
35 mm or less (50 mm or less in 35 mm format). Prop
your elbows against your sides and move the camera slowly in a small circle at a steady speed, keeping
the camera parallel or at right angles to the horizon
and being careful only to pan in the direction shown
by the guides. Use a tripod for best results. If the
desired results are not achieved, try panning at a different speed.
59
The DRIVE Dial
Q Panoramas are created from multiple frames; exposure for the entire panorama is determined by the
first frame. The camera may in some cases record an
greater or lesser angle than selected or be unable to
stitch the frames together perfectly. The last part of
the panorama may not be recorded if shooting ends
before the panorama is complete.
Q Shooting may be interrupted if the camera is panned
too quickly or too slowly. Panning the camera in a
direction other than that shown cancels shooting.
Q The desired results may not be achieved with moving subjects, subjects close to the camera, unvarying subjects such as the sky or a field of grass, subjects that are in constant motion, such as waves and
waterfalls, or subjects that undergo marked changes in brightness. Panoramas may be blurred if the
subject is poorly lit.
60
Viewing Panoramas
In full-frame playback, you can use the rear command dial to zoom panoramas in or out. Alternatively, you can play the panorama back using
the selector.
PLAY
STOP
PAUSE
Press the selector down to start playback and
press again to pause. While playback is paused,
you can scroll the panorama manually by pressing the selector left or right; vertical panoramas
will scroll vertically, horizontal panoramas horizontally. To exit to full-frame playback, press the
selector up.
Focus Mode
3
2
More on Photography and Playback
Use the focus mode selector to choose how the camera focuses (note
that regardless of the option selected, manual focus will be used when
the lens is in manual focus mode).
• S (single AF): Focus locks while the shutter button is pressed halfway.
Choose for stationary subjects.
• C (continuous AF): Focus is continually adjusted to reflect changes in the distance to the subject while the
shutter button is pressed halfway. Use for subjects that are in motion.
• M (manual): Focus manually using the lens focus ring. Rotate the ring left to reduce the focus distance,
right to increase. The manual focus indicator indicates how closely the focus distance matches the
distance to the subject in the focus brackets (the white line indicates the focus distance, the blue
bar the depth of field, or in other words the distance in front of and behind the focus point that appears to be in focus); you can also check focus visually in the viewfinder or LCD monitor. Choose for
manual control of focus or in situations in which the camera is unable to focus using autofocus (P 68).
1
0
Focus distance
(white line)
1
2
3
Manual focus
mode icon
3
2
Reduce focus
distance
55
A
35
23 18
XF
Increase focus
distance
1
2
3
0.1 0.5
M
ZOOM
18-55
1.0
0
1
1.0
2000
1.5
2.0
F5.6
3.0
5.0
200
10
Manual focus
indicator
1.5
2.0
3.0
5
Depth of field
(blue bar)
R Use the I FOCUS RING option in the setup menu (P 91) to reverse the direction of rotation of the focus ring.
R To use autofocus to focus on the subject in the selected focus area (P45), press the AF-L button. Use this feature
to quickly focus on a chosen subject in manual focus mode. Use G AUTOFOCUS SETTING > INSTANT AF
SETTING to choose whether the camera focuses using single or continuous AF (P 78).
R The camera can show focus distance in meters or feet. Use the A SCREEN SET-UP > FOCUS SCALE UNITS
option in the setup menu (P 91) to choose the units used.
R If ON is selected for G AUTOFOCUS SETTING > PRE-AF in the shooting menu (P 78), focus will be adjusted
continuously in modes S and C even when the shutter button is not pressed.
61
Focus Mode
■ The Focus Indicator
The focus indicator turns green when the subject is in focus and blinks white when
the camera is unable to focus. Brackets (“( )”) indicate that the camera is focusing
and are displayed continuously in mode C. j is displayed in manual focus mode.
3
2
1
0
1
2
3
P
1000
F3.3
400
Focus indicator
Checking Focus
To zoom in on the current focus area (P 45) for precise focus, press
the FOCUS ASSIST button. Press the button again to cancel zoom.
In manual focus mode, zoom can be adjusted by rotating the rear
command dial when STANDARD or FOCUS PEAK HIGHLIGHT is
selected for c MF ASSIST, while if ON is selected for A SCREEN
SET-UP > FOCUS CHECK, the camera will automatically zoom in
on the selected focus area when the focus ring is rotated. Focus
zoom is not available in focus mode C or when G AUTOFOCUS
SETTING > PRE-AF is on.
62
3
3
2
2
1
1
0
0
1
1
2
2
3
3
0.1 0.5
M
1.0
2000
1.5
2.0
F5.6
3.0
5.0
200
10
0.1 0.5
M
1.0
2000
1.5
2.0
F5.6
3.0
5.0
200
10
Focus Mode
R The c MF ASSIST menu can be displayed by pressing and holding the FOCUS ASSIST button.
The following options are available:
• FOCUS PEAK HIGHLIGHT: Highlights high-contrast outlines. Rotate the focus ring until
the subject is highlighted.
• DIGITAL SPLIT IMAGE: Displays a split, black-and-white image in the center of the
frame. Frame the subject in the split-image area and rotate the focus ring until
the three parts of the split image are correctly aligned.
The Dual Display
In manual focus mode, you can use the DISP/BACK button to select a dual display, with a main Entire frame
display area on the left that shows the entire frame and a smaller display area on the right
that shows a magnified view of the current focus area.
0.1 0.5
1.0
2000
1.5
2.0
More on Photography and Playback
■ MF Assist
The c MF ASSIST option in the setup menu can be used to check focus when pictures are framed in
the LCD monitor or electronic viewfinder in manual focus mode.
100
3.0
5.0
10
F5.6
Current focus area
63
Long Time-Exposures (T/B)
Select a shutter speed of T (time) or B (bulb) for long time-exposures.
R Use of a tripod is recommended to prevent the camera from moving during the exposure.
R To reduce “noise” (mottling) in long time-exposures, select ON for K LONG EXPOSURE NR in the shooting
menu (P 80). Note that this may increase the time needed to record images after shooting.
Time (T)
1 Rotate the shutter speed dial to T.
Bulb (B)
1 Rotate the shutter speed dial to B.
2 Rotate the front command dial to
2 Press the shutter button all the way
choose a shutter speed between
30 s and 2 s in steps of 1/3 EV.
down. The shutter will remain open
for up to 60 minutes while the shutter button is pressed; the display
shows the time elapsed since the
exposure started.
3
2
1
0
1
2
3
R Selecting an aperture of A fixes shutter speed at 30 s.
S
2”
200
3 Press the shutter button all the way
down to take a picture at the selected shutter speed. A count-down
timer will be displayed while the exposure is in progress.
64
Long Time-Exposures (T/B)
1 Press MENU/OK in shooting mode to display the shooting menu. Press the selector
up or down to highlight o INTERVAL TIMER SHOOTING and press MENU/OK.
2 Use the selector to choose the interval and number of shots. Press MENU/OK to
proceed.
INTERVAL/NUMBER OF TIMES
INTERVAL
NUMBER OF TIMES
24
23
22h59m59s
997
21
20
END
3 Use the selector to choose the starting time and then press MENU/OK. Shooting
will start automatically.
CANCEL
START WAITING TIME
2
1
0h
More on Photography and Playback
Interval Timer Photography
Follow the steps below to configure the camera to take photos automatically at a preset interval.
0m LATER
24
23
ESTIMATED START TIME 11:00 PM
START
CANCEL
Q Interval timer photography can not be used at a shutter speed of B (bulb) or during panorama or multiple
exposure photography. In burst mode, only one picture will be taken each time the shutter is released.
R Use of a tripod is recommended.
R Check the battery level before starting. We recommend using an optional VG-XT1 vertical battery grip with an
AC-9V AC power adapter and CP-W126 DC coupler.
R The display turns off between shots and lights a few seconds before the next shot is taken. The display can be
activated at any time by pressing the shutter button all the way down.
65
Long Time-Exposures (T/B)
Using a Remote Release
An optional RR-90 remote release can be used for
long time-exposures. See the manual provided
with the RR-90 for more information.
66
Third-Party Remote Releases
Electronic releases from thirdparty suppliers can be connected via the microphone/remote
release connector. A confirmation dialog will be displayed
when a third-party release is
connected; press MENU/OK and
select n REMOTE for MIC/REMOTE RELEASE.
CHECK MIC/REMOTE RELEASE
SETTING
SET
SKIP
0.1
0.5
1.0
1000
1.5
2.0
F3.3
3.0
5.0 10
400
Focus/Exposure Lock
1 Focus: Position the subject in the focus frame and press the shutter button halfway to lock focus and exposure. Focus and exposure will remain locked while
the shutter button is pressed halfway (AF/AE lock).
P
2000
F5.6
200
R Focus and exposure can also be locked with the AF-L and AE-L buttons, respectively (if AE/AF LOCK is
selected for d AF-LOCK MODE in the shooting menu, pressing the AF-L button will lock both focus and
exposure; P 76).
2 Recompose: Keep the shutter button pressed halfway or keep the AF-L or AE-L button pressed.
R Focus and/or exposure will remain locked while the AF-L or AE-L button is pressed,
whether or not the shutter button is pressed halfway. If AE&AF ON/OFF SWITCH is
selected for v AE/AF-LOCK MODE (P 76), focus and/or exposure lock when the
button is pressed and remain locked until the button is pressed again.
P
2000
F5.6
200
P
2000
F5.6
200
More on Photography and Playback
To compose photographs with off-center subjects:
3 Shoot: Press the button all the way down.
67
Focus/Exposure Lock
Autofocus
Although the camera boasts a high-precision autofocus system, it may be unable to focus on the subjects listed
below.
• Very shiny subjects such as mirrors or car bodies.
• Fast-moving subjects.
•
•
•
•
Subjects photographed through a window or other reflective object.
Dark subjects and subjects that absorb rather than reflect light, such as hair or fur.
Insubstantial subjects, such as smoke or flame.
Subjects that show little contrast with the background (for example, subjects in clothing that is the same color
as the background).
• Subjects positioned in front of or behind a high-contrast object that is also in the focus frame (for example, a
subject photographed against a backdrop of highly contrasting elements).
68
Recording Pictures in RAW Format
1 Press MENU/OK in shooting mode to display the shooting menu. Press the selector up or down to
highlight T IMAGE QUALITY and press MENU/OK.
2 Highlight an option and press MENU/OK. Select RAW to record only RAW images, or FINE+RAW or
NORMAL+RAW to record both JPEG copy together with the RAW images. FINE+RAW uses lower
JPEG compression ratios for higher-quality JPEG images, while NORMAL+RAW uses higher JPEG
compression ratios to increase the number of images that can be stored.
The Function Buttons
To toggle RAW image quality on or off for a single shot, assign RAW to a function button (P 79). If a JPEG option
is currently selected for image quality, pressing the button temporarily selects the equivalent JPEG+RAW option.
If a JPEG+RAW option is currently selected, pressing the button temporarily selects the equivalent JPEG option,
while if RAW is selected, pressing the button temporarily selects FINE. Taking a picture or pressing the button
again restores the previous setting.
More on Photography and Playback
To record raw, unprocessed data from the camera image sensor, select a RAW option for image quality in the shooting menu as described below. JPEG copies of RAW images can be created using the
j RAW CONVERSION option in the playback menu, or RAW images can be viewed on a computer using the RAW FILE CONVERTER application that is installed with the software on the supplied CD (P 99, 100).
R RAW image quality options are not available at sensitivities of L, H1, or H2 (P 50).
69
Recording Pictures in RAW Format
Creating JPEG Copies of RAW Pictures
RAW pictures store information on camera settings separately from the data captured by the camera
image sensor. Using the j RAW CONVERSION option in the playback menu, you can create JPEG
copies of RAW pictures using different options for the settings listed below. The original image data
are unaffected, allowing a single RAW image to be processed in a multitude of different ways.
1 Press MENU/OK during playback to display the
playback menu, then press the selector up
or down to highlight j RAW CONVERSION
and press MENU/OK to display the settings listed in the table at right.
R These options can also be displayed by pressing
Q button during playback.
2 Press the selector up or
RAW CONVERSION
REFLECT SHOOTING COND.
PUSH/PULL PROCESSING
DYNAMIC RANGE
FILM SIMULATION
WHITE BALANCE
WB SHIFT
down to highlight a setting
and press the selector right
to select. Press the selector up or down to highlight
the desired option and press MENU/OK to select
and return to the settings list. Repeat this step
to adjust additional settings.
CREATE
CANCEL
3 Press the Q button to preview the JPEG copy
and press MENU/OK to save.
70
Setting
REFLECT SHOOTING
COND.
PUSH/PULL
PROCESSING
Description
Create a JPEG copy using the settings in effect at the time the photo was taken.
Adjust exposure by –1 EV to +3 EV in increments of 1/3 EV (P 52).
Enhance details in highlights for natural
DYNAMIC RANGE
contrast (P 79).
Simulate the effects of different types of film
FILM SIMULATION
(P 42).
WHITE BALANCE Adjust white balance (P 43).
WB SHIFT
Fine-tune white balance (P 43).
COLOR
Adjust color density (P 80).
SHARPNESS
Sharpen or soften outlines (P 80).
HIGHLIGHT TONE Adjust highlights (P 80).
SHADOW TONE
Adjust shadows (P 80).
NOISE REDUCTION Process the copy to reduce mottling (P 80).
Improve definition by adjusting for diffracLENS MODULATION
tion and the slight loss of focus at the peOPTIMIZER
riphery of the lens (P 80).
Choose the color space used for color reproCOLOR SPACE
duction (P 93).
Saving Settings
1 Press MENU/OK in shooting mode to display the shooting menu. Press
O
MENU
P SHOOTING
CUSTOM 1
CUSTOM 2
CUSTOM 3
CUSTOM 4
CUSTOM 5
EDIT/SAVE CUSTOM SETTING 35mm
CUSTOM 6
OFF
50mm
CUSTOM 7
OFF
0
ON
ON
the selector up or down to highlight K EDIT/SAVE CUSTOM SETTING and press MENU/OK.
2 Highlight a custom settings bank and press MENU/OK to select. Adjust the following as desired and press DISP/BACK when adjustments are complete: U DYNAMIC RANGE, P FILM SIMULATION,
D WHITE BALANCE, f COLOR, q SHARPNESS, r HIGHLIGHT
TONE, s SHADOW TONE, and h NOISE REDUCTION.
CUSTOM 1
SAVE CURRENT SETTINGS
DYNAMIC RANGE
FILM SIMULATION
AUTO
WHITE BALANCE
COLOR
0
SHARPNESS
0
EXIT
More on Photography and Playback
Save up to 7 sets of custom camera settings for commonly-encountered situations. Saved settings can
be recalled using the u SELECT CUSTOM SETTING option in the shooting menu.
R To replace the settings in the selected bank with the settings currently selected with the camera, select
K SAVE CURRENT SETTINGS and press MENU/OK.
3 A confirmation dialog will be displayed; highlight OK and press MENU/OK.
SAVE CUSTOM SETTING
CUSTOM 1 SET OK?
OK
CANCEL
OK
71
Using a Mount Adapter
When M-mount lenses are attached using an optional FUJIFILM M MOUNT ADAPTER, the camera processes
pictures as they are taken to maintain image quality and correct for a variety of effects.
R Attaching a mount adapter enables m SHOOT WITHOUT LENS (P 81) and hides the distance indicator in the
standard display.
R Before checking focus, set the focus mode selector to M (P 61).
Mount Adapter Settings
Pressing the function button
on the mount adapter displays
l MOUNT ADAPTOR SETTING options.
MOUNT ADAPTOR SETTING
LENS 1
LENS 2
LENS 3
LENS 4
LENS 5
LENS 6
21mm
24mm
28mm
35mm
50mm
75mm
SET
■ Choosing a Focal Length
If the lens has a focal length of
21, 24, 28, or 35 mm, choose
0 5 0 mm
a matching option in the
l MOUNT ADAPTOR SETTING menu. For other lenses,
select option 5 or 6 and use the selector to enter
the focal length.
■ Distortion Correction
Choose from STRONG, MEDIUM, or WEAK options to correct BARREL or PINCUSHION
distortion.
LENS5 DISTORTION CORRECTION
BARREL STRONG
BARREL MEDIUM
BARREL WEAK
OFF
PINCUSHION WEAK
PINCUSHION MEDIUM
SET
CANCEL
LENS 5
INPUT FOCAL LENGTH
2
1
9
8
SET
72
CANCEL
Barrel distortion
Pincushion distortion
R To determine the amount required, adjust distortion correction while taking photos of graph paper
or other objects featuring repeating vertical and
horizontal lines, such as the windows in a high-rise.
Using a Mount Adapter
NEXT
SET
To use color shading correction, follow the steps
below.
1 Rotate the rear command dial to
choose a corner. The selected corner is indicated by a triangle.
2 Use the selector to adjust shading
until there is no visible difference in
color between the selected corner
and the center of the image. Press the selector
left or right to adjust colors on the cyan–red
axis, up or down to adjust colors on the blue–
yellow axis. There are a total of 19 positions
available on each axis.
■ Peripheral Illumination Correction
Choose from values between
–5 and +5. Choosing positive
0
values increases peripheral illumination, while choosing
negative values reduces peripheral illumination. Positive values are recommended for vintage lenses, negative values to
create the effect of images taken with an antique
lens or a pinhole camera.
SET
CANCEL
R To determine the amount required, adjust peripheral illumination correction while taking photos of
blue sky or a sheet of gray paper.
More on Photography and Playback
■ Color Shading Correction
Color (shading) variations between the center and edges
of the frame can be adjusted
separately for each corner.
R To determine the amount required, adjust color
shading correction while taking photos of blue sky
or a sheet of gray paper.
73
Image Search
Follow the steps below to search for pictures.
1 Press MENU/OK during playback to display the playback menu. Press the selector up or down to highlight
b IMAGE SEARCH and press MENU/OK.
2 Highlight an option and press MENU/OK.
Option
BY DATE
BY FACE
BY I FAVORITES
BY TYPE OF DATA
BY UPLOAD MARK
Description
Search by date.
Search for pictures that include faces.
Search by rating (P 26).
Find all still pictures, all movies, or all RAW pictures.
Find all pictures selected for upload to a specified destination.
3 Select a search condition. Only pictures that match the search condition will
Option
be displayed. To delete or protect selected pictures or to view the selected A ERASE
pictures in a slide show, press MENU/OK and choose from the options at right. D PROTECT
4 To end the search, select EXIT SEARCH.
74
I SLIDE SHOW
See page
83
84
85
PhotoBook Assist
Creating a PhotoBook
1 Select NEW BOOK for m PHOTOBOOK ASSIST in the playback menu (P 85) and choose
from the following options:
• SELECT FROM ALL: Choose from all available
pictures.
• SELECT BY IMAGE SEARCH: Choose from pictures
matching selected search conditions (P 74).
R Neither photographs a or smaller nor movies
can be selected for photobooks.
3 Highlight COMPLETE PHOTOBOOK and
press MENU/OK (to select all photos or all photos matching the specified search conditions
for the book, choose SELECT ALL). The new
book will be added to the list in the photobook assist menu.
Q Books can contain up to 300 pictures.
Q Books that contain no photos are automatically deleted.
More on Photography and Playback
Create books from your favorite photos.
2 Scroll through the images and press the selector up to select or deselect. To display the
current image on the cover, press the selector
down. Press MENU/OK to exit when the book is
complete.
R The first picture selected becomes the cover image. Press the selector down to select a different
image for the cover.
75
PhotoBook Assist
Viewing Photobooks
Highlight a book in the photobook assist menu
and press MENU/OK to display the book, then press
the selector left or right to scroll through the pictures.
Editing and Deleting Photobooks
Display the photobook and press MENU/OK. The
following options will be displayed; select the
desired option and follow the on-screen instructions.
• EDIT: Edit the book as described in “Creating a
PhotoBook” (P 75).
• ERASE: Delete the book.
Photobooks
Photobooks can be copied to a computer using the supplied MyFinePix Studio software (P 98).
76
Menus
Using the Menus: Shooting Mode
The shooting menu is used to adjust settings for a wide range of shooting conditions. To display the shooting menu, press MENU/OK in shooting mode. Highlight
items and press the selector right to view options, then highlight an option and
press MENU/OK. Press DISP/BACK to exit when settings are complete.
P SHOOTING MENU
BKT/Adv. SETTING
AUTOFOCUS SETTINGࠉ
ISO AUTO SETTING
IMAGE SIZE
IMAGE QUALITY
DYNAMIC RANGE
FILM SIMULATION
3:2
F
AUTO
EXIT
Shooting Menu Options (Photographs)
k BKT/Adv. SETTING
Choose the bracketing option used when the DRIVE dial is rotated to BKT (P 40, 54) or the filter used when the dial is rotated to
ADV. (P 40, 58).
Menus
77
Using the Menus: Shooting Mode
G AUTOFOCUS SETTING
Adjust autofocus settings.
Option
FOCUS AREA
MACRO
RELEASE/FOCUS
PRIORITY
INSTANT AF SETTING
AF MODE
FACE DETECTION
PRE-AF
Description
Choose the focus area (P 45).
Turn macro mode on or off (P 41).
Choose how the camera focuses in focus mode AF-S or AF-C.
• RELEASE: Shutter response is prioritized over focus. Pictures can be taken when the camera is not in focus.
• FOCUS: Focus is prioritized over shutter response. Pictures can be only taken when the camera is in focus.
Choose how the camera focuses when the AF-L button is pressed in manual focus mode (P 61).
Choose how the camera selects the focus area in focus modes S and C.
• s MULTI: When the shutter button is pressed halfway, the camera detects high-contrast subjects and
selects the focus area automatically.
• t AREA: Choose the focus area manually (P 45).
Turn Intelligent Face Detection on or off (P 38).
If ON is selected, the camera will continue to adjust focus even when the shutter-release button is not
pressed halfway. Note that this increases the drain on the battery.
If ON is selected, the AF-assist illuminator will light to assist autofocus.
R The AF-assist illuminator turns off automatically in silent mode.
AF ILLUMINATOR
Q The camera may be unable to focus using the AF-assist illuminator in some cases. If the camera is unable to focus in macro mode, try increasing the distance to the subject.
Q Avoid shining the AF-assist illuminator directly into your subject’s eyes.
N ISO AUTO SETTING
Adjust auto sensitivity settings (P 50).
78
Using the Menus: Shooting Mode
O IMAGE SIZE
Choose the size and aspect ratio at which still pictures are recorded.
Option
O
3:2
Aspect Ratio
Pictures with an aspect ratio of 3 : 2 have the same proportions as O 16 : 9
a frame of 35 mm film, while an aspect ratio of 16 : 9 is suited to O 1 : 1
display on High Definition (HD) devices. Pictures with an aspect P 3 : 2
ratio of 1 : 1 are square.
P 16 : 9
O IMAGE SIZE is not reset when the camera is turned off or an- P 1 : 1
other shooting mode is selected.
Prints at sizes up to
41 × 28 cm (16 × 11 in.)
41 × 23 cm (16 × 9 in.)
28 × 28 cm (11 × 11 in.)
29 × 20 cm (11 × 7 in.)
29 × 16 cm (11 × 6 in.)
20 × 20 cm (7 × 7 in.)
Option
Q3:2
Q 16 : 9
Q1:1
Prints at sizes up to
21 × 14 cm (8 × 5 in.)
21 × 12 cm (8 × 4 in.)
14 × 14 cm (5 × 5 in.)
U DYNAMIC RANGE
Control contrast. Choose lower values to increase contrast when shooting indoors or under overcast skies, higher values to
reduce loss of detail in highlights and shadows when photographing high-contrast scenes. Higher values are recommended
for scenes that include both sunlight and deep shade, for such high-contrast subjects as sunlight on water, brightly-lit autumn
leaves, and portraits taken against a blue sky, and for white objects or people wearing white; note, however, that mottling may
appear in pictures taken at higher values.
Menus
T IMAGE QUALITY
Choose a file format and compression ratio. Select FINE or NORMAL to record JPEG images, RAW to record RAW images, or
FINE+RAW or NORMAL+RAW to record both JPEG and RAW images. FINE and FINE+RAW use lower JPEG compression ratios
for higher-quality JPEG images, while NORMAL and NORMAL+RAW use higher JPEG compression ratios to increase the number of images that can be stored.
R If AUTO is selected, the camera will automatically choose either V 100% or W 200% according to the subject and shooting conditions. Shutter speed and aperture will be displayed when the shutter button is pressed halfway.
R W 200% is available at sensitivities of ISO 400 and above, X 400% at sensitivities of ISO 800 and above.
P FILM SIMULATION
Simulate the effects of different types of film (P 42).
B SELF-TIMER
Take pictures with the self-timer (P 35).
79
Using the Menus: Shooting Mode
o INTERVAL TIMER SHOOTING
Adjust settings for interval timer photography (P 65).
D WHITE BALANCE
Adjust colors to match the light source (P 43).
f COLOR
Adjust color density.
q SHARPNESS
Sharpen or soften outlines.
r HIGHLIGHT TONE
Adjust the appearance of highlights.
s SHADOW TONE
Adjust the appearance of shadows.
h NOISE REDUCTION
Reduce noise in pictures taken at high sensitivities.
K LONG EXPOSURE NR
Select ON to reduce mottling in long time-exposures (P 64).
j LENS MODULATION OPTIMIZER
Select ON to improve definition by adjusting for diffraction and the slight loss of focus at the periphery of the lens.
u SELECT CUSTOM SETTING
Recall settings saved with K EDIT/SAVE CUSTOM SETTING.
K EDIT/SAVE CUSTOM SETTING
Save settings (P 71).
80
Using the Menus: Shooting Mode
l MOUNT ADAPTOR SETTING
Adjust settings for M-mount lenses connected using an optional FUJIFILM M MOUNT ADAPTER (P 72).
m SHOOT WITHOUT LENS
Choose whether shutter release is enabled when no lens is attached.
c MF ASSIST
Choose how focus is displayed in manual focus mode (P 63).
• STANDARD: Focus is displayed normally (focus peaking and digital split image are not available).
• DIGITAL SPLIT IMAGE: A black-and-white split-image display.
• FOCUS PEAK HIGHLIGHT: The camera heightens high-contrast outlines. Choose a color and peaking level.
v AE/AF-LOCK MODE
If AE & AF ON WHEN PRESSING is selected, exposure and/or focus will lock while the AE-L or AF-L button is pressed. If AE & AF
ON/OFF SWITCH is selected, exposure and/or focus will lock when the AE-L or AF-L button is pressed and remain locked until
the button is pressed again.
Menus
d AF-LOCK MODE
Choose the role played by the AF-L button (P 67).
p FLASH MODE
Choose a flash mode (P 37).
I FLASH COMPENSATION
Adjust flash brightness. Choose from values between +2 EV and –2 EV. Note that the desired results may not be achieved depending on shooting conditions and the distance to the subject.
B RED EYE REMOVAL
Choose ON to remove red-eye effects caused by the flash.
R Red-eye reduction is performed only when a face is detected.
R Red-eye removal is not available with RAW images.
81
Using the Menus: Shooting Mode
W MOVIE SET-UP
Adjust movie settings (P 31).
Option
Description
Select a frame size for movie recording.
• i 1920×1080 60 fps: Full HD (60 fps)
MOVIE MODE
• i 1920×1080 30 fps: Full HD (30 fps)
• h 1280×720 60 fps: HD (60 fps)
• h 1280×720 30 fps: HD (30 fps)
MIC LEVEL ADJUSTMENT Adjust the microphone recording level.
Specify whether the device connected to the microphone/remote release connector is a microphone or
MIC/REMOTE RELEASE
a remote release (P 32, 66).
L IS MODE
Reduce blur. This option is available only with lenses that support image stabilization.
• l CONTINUOUS: Image stabilization on.
• m SHOOTING ONLY: Image stabilization enabled only when the shutter button is pressed halfway or the shutter is released.
• OFF: Image stabilization off ; x appears in the display (P 5). Recommended when using a tripod.
r WIRELESS COMMUNICATION
Connect to a smartphone or tablet over a wireless network (P 97).
R For more information, visit http://fujifilm-dsc.com/wifi/.
e APERTURE SETTING
Choose the method used to adjust aperture when using lenses with no aperture rings.
• AUTO + o MANUAL: Rotate the rear command dial to choose the aperture. Rotate past minimum aperture to choose A (auto).
• AUTO: Aperture is selected automatically; camera functions in exposure mode P (program AE) or S (shutter-priority AE).
• MANUAL: Rotate the rear command dial to choose the aperture; camera functions in exposure mode A (aperture-priority AE)
or M (manual).
R Aperture can not be adjusted while the view through the camera lens is zoomed in.
82
Using the Menus: Playback Mode
To display the playback menu, press MENU/OK in playback mode. Highlight items
and press the selector right to view options, then highlight an option and press
MENU/OK. Press DISP/BACK to exit when settings are complete.
PLAYBACK MENU
WIRELESS COMMUNICATION
RAW CONVERSION
ERASE
CROP
RESIZE
PROTECT
IMAGE ROTATE
EXIT
Playback Menu Options
r WIRELESS COMMUNICATION
Connect to a smartphone or tablet over a wireless network (P 97).
R For more information, visit http://fujifilm-dsc.com/wifi/.
j RAW CONVERSION
Create JPEG copies of RAW pictures (P 70).
G CROP
Create a cropped copy of the current picture.
Menus
A ERASE
Delete pictures (P 30).
1 Display the desired picture.
2 Select G CROP in the playback menu.
3 Use the rear command dial to zoom in and out and press the selector up, down, left, or right to scroll the picture until the
desired portion is displayed.
4 Press MENU/OK to display a confirmation dialog.
5 Press MENU/OK again to save the cropped copy to a separate file.
R Larger crops produce larger copies; all copies have an aspect ratio of 3 : 2. If the size of the final copy will be a, OK will be
displayed in yellow.
83
Using the Menus: Playback Mode
e RESIZE
Create a cropped copy of the current picture.
1 Display the desired picture.
2 Select e RESIZE in the playback menu.
3 Highlight a size and press MENU/OK to display a confirmation dialog.
4 Press MENU/OK again to save the resized copy to a separate file.
R The sizes available vary with the size of the original image.
D PROTECT
Protect pictures from accidental deletion. Highlight one of the following options and press MENU/OK.
• FRAME: Protect selected pictures. Press the selector left or right to view pictures and press MENU/OK to select or deselect. Press
DISP/BACK when the operation is complete.
• SET ALL: Protect all pictures.
• RESET ALL: Remove protection from all pictures.
Q Protected pictures will be deleted when the memory card is formatted (P 94).
C IMAGE ROTATE
Rotate pictures.
1 Display the desired picture.
2 Select C IMAGE ROTATE in the playback menu.
3 Press the selector down to rotate the picture 90° clockwise, up to rotate it 90° counterclockwise.
4 Press MENU/OK. The picture automatically be displayed in the selected orientation whenever it is played back on the camera.
R Protected pictures can not be rotated. Remove protection before rotating pictures.
R The camera may not be able to rotate pictures created with other devices. Pictures rotated on the camera will not be rotated
when viewed on a computer or on other cameras.
R Pictures taken with A SCREEN SET-UP > AUTOROTATE PB are automatically displayed in the correct orientation during
playback (P 91).
84
Using the Menus: Playback Mode
B RED EYE REMOVAL
Remove red-eye from portraits. The camera will analyze the image; if red-eye is detected, the image will be processed to create
a copy with reduced red-eye.
1 Display the desired picture.
2 Select B RED EYE REMOVAL in the playback menu.
3 Press MENU/OK.
R Red eye may not be removed if the camera is unable to detect a face or the face is in profile. Results may differ depending on
the scene. Red eye can not be removed from pictures that have already been processed using red-eye removal or pictures
created with other devices.
R The amount of time needed to process the image varies with the number of faces detected.
R Copies created with B RED EYE REMOVAL are indicated by a e icon during playback.
R Red eye removal can not be performed on RAW images.
Option
NORMAL
FADE-IN
NORMAL g
FADE-IN g
MULTIPLE
Description
Press the selector left or right to go back or skip ahead one frame. Select FADE-IN for fade transitions between
frames.
Menus
I SLIDE SHOW
View pictures in an automated slide show. Choose the type of show and press MENU/OK to start. Press DISP/BACK at any time during the show to view on-screen help. The show can be ended at any time by pressing MENU/OK.
As above, except that camera automatically zooms in on faces.
Display several pictures at once.
R The camera will not turn off automatically while a slide show is in progress.
m PHOTOBOOK ASSIST
Create books from your favorite photos (P 75).
85
Using the Menus: Playback Mode
j MARK FOR UPLOAD TO
Select pictures for upload to YouTube, Facebook or MyFinePix.com using MyFinePix Studio (Windows only).
1 Select YouTube to choose movies for upload to YouTube, Facebook to choose photos and movies for upload to Facebook,
or MyFinePix.com to choose photos for upload to MyFinePix.com.
2 Press the selector left or right to display pictures and press MENU/OK to select or deselect. Press DISP/BACK to exit when all the
desired pictures are selected.
R
R
R
R
Only movies can be selected for upload to YouTube.
Only photos can be selected for upload to MyFinePix.com.
During playback, selected pictures are indicated by j YouTube, j Facebook or j MyFinepix.com icons.
Choose RESET ALL to deselect all pictures. If the number of pictures affected is very large, some time may be required to
complete the operation. Press DISP/BACK to exit before the operation is complete.
Uploading Pictures (Windows Only)
Selected pictures can be uploaded using the YouTube/Facebook/ Select with camera
MyFinePix.com Upload option in MyFinePix Studio. For information on
installing MyFinePix Studio and connecting the camera to a computer, see
“Viewing Pictures on a Computer”(P
Computer”(P 98).).
b IMAGE SEARCH
Search for pictures (P 74).
s PC AUTO SAVE
Upload pictures to a computer over a wireless network (P 97).
R For more information, visit http://fujifilm-dsc.com/wifi/.
K PRINT ORDER (DPOF)
Select pictures for printing on DPOF- and PictBridge-compatible devices (P 105).
86
Upload from computer
Using the Menus: Playback Mode
J DISP ASPECT
Choose how High Definition (HD) devices display pictures with an aspect ratio of 3 : 2
(this option is available only when an HDMI cable is connected). Select 16 : 9 to display
the image so that it fills the screen with its top and bottom cropped out, 3 : 2 to display
the entire image with black bands at either side.
16 : 9
3:2
16 : 9
3:2
Menus
87
The Setup Menu
Using the Setup Menu
1 Display the setup menu.
1.1 Press MENU/OK to display the menu for the current mode.
1.2 Press the selector left to highlight the tab for the current menu.
1.3 Press the selector down to highlight the setup menu tab containing the desired option.
SET-UP
DATE/TIME
TIME DIFFERENCE
ENGLISH
RESET
SILENT MODE
SOUND SET-UP
SCREEN SET-UP
OFF
EXIT
Tab
1.4 Press the selector right to place the cursor in the setup menu.
2 Adjust settings.
Highlight items and press the selector right to view options, then highlight an option and press
MENU/OK. Press DISP/BACK to exit when settings are complete.
88
The Setup Menu
Setup Menu Options
F DATE/TIME
Set the camera clock (P 18).
N TIME DIFFERENCE
Switch the camera clock instantly from your home time zone to the local time at your destination when traveling. To specify the
difference between local time and your home time zone:
1 Highlight g LOCAL and press MENU/OK.
2 Use the selector to choose the time difference between local time and your home time zone. Press MENU/OK when settings
are complete.
To set the camera clock to local time, highlight g LOCAL and press MENU/OK. To set the clock to the time in your home time
zone, select h HOME. If g LOCAL is selected, g will be displayed for three seconds when the camera is turned on.
R RESET
Reset shooting or setup menu options to default values. Custom white balance, custom settings banks created using K EDIT/
SAVE CUSTOM SETTING
SETTING, and F DATE/TIME, N TIME DIFFERENCE, A SCREEN SET-UP > BACKGROUND COLOR, the wireless options in the shooting menu, and the setup menu r WIRELESS SETTINGS > GENERAL SETTINGS and PC AUTO SAVE
SETTINGS options are not affected.
Menus
Qa
Choose a language (P 18).
1 Highlight the desired option and press the selector right.
2 A confirmation dialog will be displayed; highlight OK and press MENU/OK.
o SILENT MODE
Select ON to disable the speaker, flash, and illuminator in situations in which camera sounds or lights may be unwelcome (note
that silent mode can not be enabled or disabled during movie playback). o appears in the display when silent mode is on.
89
The Setup Menu
b SOUND SET-UP
Adjust sound settings.
Option
OPERATION VOL.
PLAYBACK VOLUME
Description
Adjust the volume of the sounds produced when camera controls are operated. Choose e OFF
(mute) to disable control sounds.
Adjust the volume for movie playback.
A SCREEN SET-UP
Adjust display settings.
Option
Description
Choose how long images are displayed after shooting. Colors may differ slightly from those in the final
image and “noise” mottling may be visible at high sensitivities.
Option
IMAGE DISP.
CONTINUOUS
1.5 SEC
0.5 SEC
OFF
EVF AUTOROTATE DISPLAYS
PREVIEW EXP. IN MANUAL
MODE
EVF/LCD BRIGHTNESS
90
Description
Pictures are displayed until the MENU/OK button is pressed or the shutter button is
pressed halfway. To zoom in on the active focus point, press the FOCUS ASSIST button; press again to cancel zoom.
Pictures are displayed for 1.5 seconds (1.5 SEC) or 0.5 seconds (0.5 SEC) or until
the shutter button is pressed halfway.
Pictures are not displayed after shooting.
Choose whether the indicators in the viewfinder rotate to match camera orientation (P 20). Regardless
of the option selected, the indicators in the monitor do not rotate.
Select ON to enable exposure preview in manual exposure mode. Select OFF when using a flash or
on other occasions on which exposure may change when the picture is taken.
Control the brightness of the display.
The Setup Menu
A SCREEN SET-UP (Continued)
Option
Description
Choose the type of framing grid available in shooting mode.
F GRID 9
G GRID 24
H HD FRAMING
A six-by-four grid.
Frame HD pictures in the crop
shown by the lines at the top and
bottom of the display.
FRAMING GUIDELINE
P
For “rule of thirds” composition.
FOCUS CHECK
FOCUS SCALE UNITS
DISP. CUSTOM SETTING
P
Choose ON to automatically rotate “tall” (portrait-orientation) pictures during playback.
Choose a color scheme.
If ON is selected, the camera will automatically zoom in on the view through the lens when the focus
ring is rotated in manual focus mode (P 62).
Choose the units used for the focus distance indicator (P 61).
Choose items for the custom display (P 22).
Menus
AUTOROTATE PB
BACKGROUND COLOR
P
F FUNCTION (Fn) SETTING
Choose the roles played by the function buttons (P 39).
e COMMAND DIAL SETTING
Choose the roles played by the command dials.
N ISO DIAL SETTING
Choose sensitivity values for the H1 and H2 positions on the ISO dial (P 50).
I FOCUS RING
Choose the direction in which the focus ring is rotated to increase the focus distance.
91
The Setup Menu
Z POWER MANAGEMENT
Adjust power management settings.
Option
AUTO POWER OFF
HIGH PERFORMANCE
Description
Choose the length of time before the camera turns off automatically when no operations are performed.
Shorter times increase battery life; if OFF is selected, the camera must be turned off manually. Note that in
some situations the camera turns off automatically even when OFF is selected.
Select ON for faster focus and to reduce the time needed to restart the camera after it has been turned off.
V SENSOR CLEANING
Remove dust from the camera image sensor.
• OK: Clean sensor immediately (P xi).
• WHEN SWITCHED ON: If this option is selected, sensor cleaning will be performed when the camera turns on.
• WHEN SWITCHED OFF: If this option is selected, sensor cleaning will be performed when the camera turns off (sensor cleaning is
not however performed if the camera turns off in playback mode).
R Dust that can not be removed using sensor cleaning can be removed manually (P 116).
92
The Setup Menu
t SAVE DATA SET-UP
Adjust file management settings.
Option
FRAME NO.
Description
New pictures are stored in image files named using a four-digit file number assigned by
Frame number
adding one to the last file number used. The file number is displayed during playback as
100-0001
shown at right. FRAME NO. controls whether file numbering is reset to 0001 when a new
memory card is inserted or the current memory card is formatted.
Directory
File
number number
Option
Description
Numbering continues from the last file number used or the first available file number, whichever is
CONTINUOUS
higher. Choose this option to reduce the number of pictures with duplicate file names.
RENEW
Numbering is reset to 0001 after formatting or when a new memory card is inserted.
Menus
R If the frame number reaches 999-9999, the shutter release will be disabled (P 123).
R Selecting R RESET (P 89) sets FRAME NO. to CONTINUOUS but does not reset the file number.
R Frame numbers for pictures taken with other cameras may differ.
SAVE ORG IMAGE Choose ON to save unprocessed copies of pictures taken using B RED EYE REMOVAL.
Change the file name prefix. sRGB images use a four-letter prefix (default “DSCF”), Adobe RGB images a threeEDIT FILE NAME
letter prefix (“DSF”) preceded by an underscore.
J COLOR SPACE
Choose the gamut of colors available for color reproduction.
Option
sRGB
Adobe RGB
Description
Recommended in most situations.
For commercial printing.
93
The Setup Menu
r WIRELESS SETTINGS
Adjust settings for connection to wireless networks.
Option
GENERAL SETTINGS
RESIZE IMAGE FOR
SMARTPHONE H
PC AUTO SAVE
SETTINGS
Description
Choose a name (NAME) to identify the camera on the wireless network (the camera is assigned a unique
name by default) or select RESET WIRELESS SETTINGS to restore default settings.
Choose ON (the default setting, recommended in most circumstances) to resize larger images to H for upload to smartphones, OFF to upload images at their original size. Resizing applies only to the copy uploaded
to the smartphone; the original is not affected.
Choose DELETE REGISTERED DESTINATION PC to remove selected destinations, DETAILS OF PREVIOUS
CONNECTION to view computers to which the camera has recently connected.
R For more information, visit http://fujifilm-dsc.com/wifi/.
s PC AUTO SAVE SETTING
Choose an upload destination. Choose SIMPLE SETUP to connect using WPS, MANUAL SETUP to configure network settings
manually.
R For more information, visit http://fujifilm-dsc.com/wifi/.
U GEOTAGGING SET-UP
View location data downloaded from a smartphone and choose whether to save the data with your pictures.
Option
GEOTAGGING
LOCATION INFO
Description
Choose whether location data downloaded from a smartphone are embedded in pictures as they are taken.
Display the location data last downloaded from a smartphone.
R For more information, visit http://fujifilm-dsc.com/wifi/.
K FORMAT
Select OK to format the memory card.
Q All data—including protected pictures—will be deleted from the memory card. Be sure important files have been copied to
a computer or other storage device.
Q Do not open the battery-chamber cover during formatting.
94
Factory Defaults
The factory default settings for the options in the shooting and setup menus are listed below. These
settings can be restored using the R RESET option in the setup menu (P 89).
■ Shooting Menu
Menu
k BKT/Adv. SETTING
BKT SELECT
Adv. FILTER SELECT
G AUTOFOCUS SETTING
MACRO
RELEASE/FOCUS PRIORITY
O AE BKT
G TOY CAMERA
OFF
• AF-S PRIORITY SELECTION: RELEASE
• AF-C PRIORITY SELECTION: RELEASE
AF-S
t AREA
OFF
OFF
ON
200
800
1/60
O3:2
FINE
V 100%
c PROVIA/STANDARD
OFF
AUTOS
(0) MID
(0) STANDARD
(0) STANDARD
Menu
s SHADOW TONE
h NOISE REDUCTION
K LONG EXPOSURE NR
j LENS MODULATION OPTIMIZER
l MOUNT ADAPTOR SETTING
m SHOOT WITHOUT LENS
c MF ASSIST
v AE/AF-LOCK MODE
d AF-LOCK MODE
p FLASH MODE
I FLASH COMPENSATION
B RED EYE REMOVAL
W MOVIE SET-UP
MOVIE MODE
MIC LEVEL ADJUSTMENT
MIC/REMOTE RELEASE
L IS MODE
e APERTURE SETTING
Default
(0) STANDARD
(0) STANDARD
ON
ON
LENS 5 (50mm)
OFF
STANDARD
AE&AF ON WHEN PRESSING
AF LOCK ONLY
AUTO
±0
OFF
Menus
INSTANT AF SETTING
AF MODE
FACE DETECTION
PRE-AF
AF ILLUMINATOR
N ISO AUTO SETTING
DEFAULT SENSITIVITY
MAX. SENSITIVITY
MIN. SHUTTER SPEED
O IMAGE SIZE
T IMAGE QUALITY
U DYNAMIC RANGE
P FILM SIMULATION
B SELF-TIMER
D WHITE BALANCE
f COLOR
q SHARPNESS
r HIGHLIGHT TONE
Default
i 1920 × 1080 60 fps
3
m MIC
l CONTINUOUS
AUTO + o MANUAL
95
Factory Defaults
■ Setup Menu
Menu
o SILENT MODE
b SOUND SET-UP
OPERATION VOL.
PLAYBACK VOLUME
A SCREEN SET-UP
IMAGE DISP.
EVF AUTOROTATE DISPLAYS
PREVIEW EXP. IN MANUAL MODE
EVF/LCD BRIGHTNESS
FRAMING GUIDELINE
AUTOROTATE PB
FOCUS CHECK
FOCUS SCALE UNITS
DISP. CUSTOM SETTING
F FUNCTION (Fn) SETTING
Fn1
Fn2
Fn3
Fn4
Fn5
Fn6
e COMMAND DIAL SETTING
N ISO DIAL SETTING
I FOCUS RING
Z POWER MANAGEMENT
AUTO POWER OFF
HIGH PERFORMANCE
96
Default
OFF
c
7
OFF
ON
ON
0
F GRID 9
ON
OFF
METERS
All options selected
k BKT/Adv. SETTING
r WIRELESS COMMUNICATION
p MACRO
P FILM SIMULATION
D WHITE BALANCE
i FOCUS AREA
Y S.S. X F
• H1: 12800
• H2: 25600
X CW
2 MIN
OFF
Menu
V SENSOR CLEANING
WHEN SWITCHED ON
WHEN SWITCHED OFF
t SAVE DATA SET-UP
FRAME NO.
SAVE ORG IMAGE
J COLOR SPACE
r WIRELESS SETTINGS
RESIZE IMAGE FOR
SMARTPHONE H
U GEOTAGGING SET-UP
GEOTAGGING
LOCATION INFO
Default
OFF
ON
CONTINUOUS
OFF
sRGB
ON
ON
ON
Connections
Wireless Transfer
Access wireless networks and connect to computers, smartphones, or tablets. For downloads and
other information, visit http://fujifilm-dsc.com/wifi/.
Wireless Connections: Smartphones
Install the “FUJIFILM Camera Remote” app on your
smartphone to browse the images on the camera, download selected images, control the camera remotely, or copy location data to the camera.
To connect to the smartphone, press the camera
Wi-Fi button in playback mode.
Connections
R You can also connect using the r WIRELESS
COMMUNICATION options in the camera shooting
and playback menu. To connect in shooting mode,
assign WIRELESS COMMUNICATION to a function
button (P 39).
Wireless Connections: Computers
Once you have installed the“FUJIFILM PC AutoSave”
application and configured your computer as a
destination for the images copied from the camera, you can upload pictures from the camera using the s PC AUTO SAVE option in the camera
playback menu or by pressing and holding the
Wi-Fi button in playback mode.
97
Viewing Pictures on a Computer
The supplied software can be used to copy pictures to a computer, where they can be stored, viewed,
organized, and printed. Before proceeding, install the software as described below. Do NOT connect
the camera to the computer until installation is complete.
Windows: Installing MyFinePix Studio
1 Confirm that the computer meets the following system requirements:
CPU
RAM
Free disk space
Windows 8/Windows 7 (Service Pack 1) /
Windows Vista (Service Pack 2) 1
3 GHz Pentium 4 or better
(2.4 GHz Core 2 Duo or better 2)
1 GB or more
Windows XP (Service Pack 3) 1
2 GHz Pentium 4 or better
(2.4 GHz Core 2 Duo or better 2)
512 MB or more (1 GB or more 2)
2 GB or more
Supports DirectX 7 or later (required; performance
GPU
Supports DirectX 9 or later (recommended)
not guaranteed with other GPUs)
Video
1024 × 768 pixels or more with 24-bit color or better
• Built-in USB port recommended. Operation is not guaranteed with other USB ports.
• .NET Framework 3.5 Service Pack 1 required when uploading images or using Map Viewer.
Other
• Internet connection (broadband recommended) required to install .NET Framework (if necessary), to use
auto update feature, and when performing such tasks as sharing pictures on-line or via e-mail.
1 Other versions of Windows are not supported. Only pre-installed operating systems are supported; operation is not guaranteed on home-built computers or computers that have been upgraded from earlier versions of Windows.
2 Recommended when displaying HD movies.
2 Start the computer. Log in to an account with administrator privileges before proceeding.
98
Viewing Pictures on a Computer
3 Exit any applications that may be running and insert the installer CD in a CD-ROM drive.
Windows 8/Windows 7/Windows Vista
If an AutoPlay dialog is displayed, click SETUP.EXE. A “User Account Control” dialog will then be displayed;
click Yes (Windows 8/Windows 7) or Allow (Windows Vista).
The installer will start automatically; click Install MyFinePix Studio and follow the on-screen instructions to install MyFinePix Studio and RAW FILE CONVERTER.
4 If prompted to install Windows Media Player or DirectX, follow the on-screen instructions to com-
Connections
If the Installer Does Not Start Automatically
If the installer does not start automatically, follow the steps below.
• Windows 8: Select Desktop from the Start screen, then select File Explorer on the desktop taskbar and
choose Computer in the navigation panel. Double-click the drive containing the installer CD and follow
the on-screen instructions.
• Other versions of Windows: Select Computer or My Computer from the Start menu, then double-click the
FINEPIX CD icon to open the FINEPIX CD window and double-click setup or SETUP.EXE.
plete installation.
5 Remove the installer CD from the CD-ROM drive when installation is complete. Store the installer
CD in a dry location out of direct sunlight in case you need to re-install the software.
Installation is now complete. Proceed to “Connecting the Camera” (P 101).
99
Viewing Pictures on a Computer
Macintosh: Installing RAW FILE CONVERTER
RAW FILE CONVERTER is used to view RAW images on your computer.
1 Confirm that the computer meets the following system requirements:
CPU
OS
RAM
Free disk space
Video
Intel (Core 2 Duo or better)
Pre-installed copies of Mac OS X version 10.6–10.9 (visit http://www.fujifilm.com/support/digital_cameras/
compatibility/ for more information).
1 GB or more
A minimum of 200 MB required for installation with 400 MB available when RAW FILE CONVERTER is running
1,024 × 768 pixels or more with 24-bit color or better
2 After starting the computer and quitting any applications that may be running, insert the installer
CD in a CD-ROM drive and double-click SILKYRFCEXInstaller.
3 Enter an administrator name and password when prompted and click OK, then follow the onscreen instructions to install. Click Exit to quit the installer when installation is complete.
4 Remove the installer CD from the CD-ROM drive. Note that you may be unable to remove the CD
if Safari is running; if necessary, quit Safari before removing the CD. Store the installer CD in a dry
location out of direct sunlight in case you need to re-install the software.
Installation is now complete. Proceed to “Connecting the Camera” (P 101).
100
Viewing Pictures on a Computer
Connecting the Camera
1 Find a memory card containing pictures you want to copy to the computer and insert the card into
the camera (P 14).
R Windows users may require the Windows CD when starting the software for the first time.
Q Loss of power during transfer could result in loss of data or damage to the memory card. Insert a fresh or
fully-charged battery before connecting the camera.
2 Turn the camera off and connect a USB cable (available separately from third-party suppliers) as shown, making sure the
connectors are fully inserted. Connect the camera directly to
the computer; do not use a USB hub or keyboard.
3 Turn the camera on.
4 Upload pictures in MyFinePix Studio and follow the on-screen instructions to copy pictures to the
computer. To exit without copying pictures, click Cancel.
Connections
Q The USB cable must be no more than 1.5 m (4.9 ft.) long and be suitable for data transfer.
Copying Pictures to Macintosh Computers (Mac OS)
Use a standard Mac OS application such as Image Capture to copy pictures or movies to a Mac.
For more information on using the supplied software, start the application and select the appropriate
option from the Help menu.
101
Viewing Pictures on a Computer
Q If a memory card containing a large number of images is inserted, there may be a delay before the software
starts and you may be unable to import or save images. Use a memory card reader to transfer pictures.
Q Make sure that the computer does not display a message stating that copying is in progress and that the indicator lamp is out before turning the camera off or disconnecting the USB cable (if the number of images copied is very large, the indicator lamp may remain lit after the message has cleared from the computer display).
Failure to observe this precaution could result in loss of data or damage to the memory card.
Q Disconnect the camera before inserting or removing memory cards.
Q In some cases, it may not be possible to access pictures saved to a network server using the supplied software
in the same way as on a standalone computer.
Q The user bears all applicable fees charged by the phone company or Internet service provider when using
services that require an Internet connection.
Disconnecting the Camera
After confirming that the indicator lamp is out, turn the camera off and disconnect the USB cable.
Uninstalling the Supplied Software
Only uninstall the supplied software when it is no longer required or before beginning reinstallation. After
quitting the software and disconnecting the camera, drag “RAW FILE CONVERTER EX powered by SILKYPIX” from
“Applications” into the Trash and select Empty Trash in the Finder menu (Macintosh), or open the control panel
and use “Programs and Features” (Windows 8/Windows 7/Windows Vista) or “Add or Remove Programs” (Windows XP) to uninstall MyFinePix Studio. Under Windows, one or more confirmation dialogs may be displayed;
read the contents carefully before clicking OK.
102
Printing Pictures via USB
If the printer supports PictBridge, the camera can be connected directly to the printer and
pictures can be printed without first being copied to a computer. Note that depending on the
printer, not all the functions described below may be supported.
Connecting the Camera
1 Connect a USB cable (available separately
from third-party suppliers) as shown and turn
the printer on.
Printing Selected Pictures
1 Press the selector left or right to display a picture you wish to print.
R To print one copy of the current picture, proceed directly to Step 3.
2 Press the selector up or down to
2 Turn the camera on. t USB will be displayed
in the monitor, followed by the PictBridge display shown below at right.
USB
3 Press MENU/OK to display a confirmation dialog.
PRINT THESE FRAMES
TOTAL: 9 SHEETS
Connections
Q The USB cable must be no more than 1.5 m
(4.9 ft.) long and be suitable for data transfer.
choose the number of copies (up to
99). Repeat steps 1–2 to select additional pictures.
PICTBRIDGE
TOTAL: 00000
00 SHEETS
FRAME
OK
SET
R Pictures can be printed from memory cards that has
been formatted in the camera.
R Page size, print quality, and border selections are
made using the printer.
YES
CANCEL
4 Press MENU/OK to start printing.
103
Printing Pictures via USB
Printing the Date of Recording
To print the date of recording on pictures, press
DISP/BACK in the PictBridge display and select PRINT
WITH DATE s (to print pictures without the date of
recording, select PRINT WITHOUT DATE). To ensure
that the date is correct, set the camera clock before
taking pictures. Some printers do not support date
printing. See the printer manual for details.
Printing the DPOF Print Order
To print the print order created with K PRINT
ORDER (DPOF) in the playback menu (P 86):
1 In the PictBridge display, press DISP/
BACK to open the PictBridge menu.
2 Press the selector up or down to
highlight u PRINT DPOF.
PICTBRIDGE
PRINT WITH DATE s
PRINT WITHOUT DATE
PRINT DPOF
3 Press MENU/OK to display a confirmation dialog.
PRINT DPOF OK?
TOTAL: 9 SHEETS
YES
CANCEL
4 Press MENU/OK to start printing.
104
Printing Pictures via USB
During Printing
The message shown at right is
displayed during printing. Press
DISP/BACK to cancel before all
pictures are printed (depending
on the printer, printing may end
before the current picture has
printed).
PRINTING
Creating a DPOF Print Order
The K PRINT ORDER (DPOF) option in the playback menu can be used to create a digital “print
order” for PictBridge-compatible printers or devices that support DPOF.
CANCEL
If printing is interrupted, turn the camera off and
then on again.
Connections
Disconnecting the Camera
Confirm that the above message is not displayed and
turn the camera off. Disconnect the USB cable.
DPOF
DPOF (Digital Print Order Format) is standard that allows pictures to be printed from
“print orders” stored on the memory card.
The information in the order includes the
pictures to be printed and the number of copies of
each picture.
105
Printing Pictures via USB
■ WITH DATE s/ WITHOUT DATE
To modify the DPOF print order, select K PRINT
ORDER (DPOF) in the playback menu and press
the selector up or down to highlight WITH
DATE s or WITHOUT DATE.
3 Repeat steps 1–2 to complete the
WITH DATE s: Print date of recording
on pictures.
4 The total number of prints is dis-
Y
PLAYBACK
MENU
RED EYE REMOVAL
SLIDE SHOW
WITH DATE s
PHOTOBOOK ASSIST
WITHOUT DATE
MARK FOR UPLOAD TO
RESET ALL
IMAGE SEARCH
PC AUTO SAVE
PRINT ORDER (DPOF)
WITHOUT DATE: Print pictures without
date.
Press MENU/OK and follow the steps below.
1 Press the selector left or right to display a picture you wish to include in
or remove from the print order.
2 Press the selector up or down to
choose the number of copies (up
to 99). To remove a picture from the
order, press the selector down until
the number of copies is 0.
PRINT ORDER (DPOF)
DPOF: 00001
Total number of prints
Number of copies
01 SHEETS
FRAME
106
SET
print order. Press MENU/OK to save
the print order when settings are
complete, or DISP/BACK to exit without changing the print order.
played in the monitor. Press MENU/OK
to exit.
The pictures in the current
print order are indicated by a
u icon during playback.
Printing Pictures via USB
■ RESET ALL
To cancel the current print
order, select RESET ALL for
K PRINT ORDER (DPOF). The
confirmation shown at right
will be displayed; press MENU/OK
to remove all pictures from the
order.
RESET DPOF OK?
YES
CANCEL
R Print orders can contain a maximum of 999 pictures.
RESET DPOF OK?
R If a memory card is inserted
containing a print order created by another camera, the
message shown at right will
YES
NO
be displayed. Pressing MENU/OK
cancels the print order; a new
print order must be created as
described above.
Connections
107
Viewing Pictures on TV
To show pictures to a group, connect the camera to a TV using an HDMI cable (available separately
from third-party suppliers; note that the TV can only be used for playback, not shooting).
1 Turn the camera off.
2 Connect the cable as shown below.
Insert into
HDMI connector
Insert into
HDMI mini connector
Q Use an HDMI cable no more than 1.5 m (4.9 ft.) long.
R Be sure the connectors are fully inserted.
3 Tune the television to the HDMI input channel. See the documentation supplied with the television for details.
4 Turn the camera on and press a button. The camera monitor turns off and pictures and movies
are played back on the TV. Note that the camera volume controls have no effect on sounds played
on the TV; use the television volume controls to adjust the volume.
R The USB cable can not be used while an HDMI cable is connected.
R Some televisions may briefly display a black screen when movie playback begins.
108
Technical Notes
Optional Accessories
The camera supports a wide range of accessories from FUJIFILM and other manufacturers.
Accessories from FUJIFILM
The following optional accessories are available from FUJIFILM. For the latest information on the accessories available in your region, check with your local FUJIFILM representative or visit http://www.fujifilm.com/
products/digital_cameras/index.html.
Rechargeable Li-ion batteries
NP-W126: Additional large-capacity NP-W126 rechargeable batteries can be purchased as required.
Remote releases
RR-90: Use to reduce camera shake or keep the shutter open during a time exposure.
Technical Notes
Battery chargers
BC-W126: Replacement battery chargers can be purchased as required. At+20 °C/+68 °F, the BC-W126 charges an NP-W126 in about 150 minutes.
Stereo microphones
MIC-ST1: An external microphone for movie recording.
109
Optional Accessories
FUJINON lenses
XF-series lenses: Interchangeable lenses for use exclusively with the FUJIFILM X-mount.
XC-series lenses: Interchangeable lenses for use exclusively with the FUJIFILM X-mount.
Shoe-mounted flash units
EF-20: This clip-on flash unit (powered by two AA batteries) has a Guide Number of 20/65 (ISO 100, m/ft.) and
supports TTL flash control. The flash head can be rotated upwards 90° for bounce lighting.
EF-42: This clip-on flash unit (powered by four AA batteries) has a Guide Number of 42/137 (ISO 100, m/ft.)
and supports TTL flash control and auto power zoom in the range 24–105 mm (35 mm format equivalent).
The flash head can be rotated 90° up, 180° left, or 120° right for bounce lighting.
EF-X20: This clip-on flash unit has a Guide Number of 20/65 (ISO 100, m/ft.).
Mount adapters
FUJIFILM M MOUNT ADAPTER: Allows the camera to be used with a wide selection of M-mount lenses.
Protector filters
PRF-39/PRF-49S/PRF-52/PRF-58/PRF-62/PRF-72: Use to protect the lens.
Grips
MHG-XT: Features an improved grip. Batteries and memory cards can be removed with the grip in place, and the grip is equipped
with a rail for quick-shoe camera mounts. The tripod mount can be aligned with the lens optical axis.
Leather cases
BLC-XT1: This case combines practicality with the luxury of leather and comes with a shoulder strap made of the same material,
as well as a cloth that can be used to wrap the camera before putting it in the case and on other occasions. Pictures can be
taken and batteries inserted or removed with the camera still in its case.
110
Optional Accessories
Front lens caps
FLCP-39/FLCP-52/FLCP-58/FLCP-62/FLCP-72: Protect the front lens element when the lens is not in use.
Rear lens caps
RLCP-001: Protect the rear lens element when the lens is not attached to the camera.
Body caps
BCP-001: Cover the camera lens mount when no lens is attached.
Battery grips
VG-XT1: This grip accommodates an extra battery for improved endurance and makes it easier to hold the
camera rotated 90 ° to frame pictures in “tall” (portrait) orientation. The tripod mount can be aligned with
the lens optical axis.
AC power adapters
AC-9V (requires CP-W126 DC coupler and VG-XT1 vertical battery grip): Use for extended shooting and playback or when copying pictures to a
computer.
Technical Notes
DC couplers
CP-W126: Connect the AC-9V to the VG-XT1.
111
Optional Accessories
Connecting the Camera to Other Devices
■ Remote Shutter Releases
■ External Microphones
X-T1
MIC-ST1 stereo microphone *
■ Flash Photography
RR-90 remote release *
■ Printing
USB cable †
■ Battery Grips
PictBridgecompatible
printer †
Printer †
■ Computer Related
EF-20 shoeEF-42 shoeEF-X20 shoemounted flash * mounted flash * mounted flash *
■ Lenses
VG-XT1
vertical battery grip *
SD/SDHC/SDXC
memory card †
XF-series lenses *
■ M Mount Adapters
USB cable †
Computer †
* Available separately from FUJIFILM.
† Available separately from third-party suppliers. USB and
HDMI cables must be no more than 1.5 m (4.9 ft.) long.
112
XC-series lenses *
FUJIFILM M mount adapter *
■ Audio/Visual
HDMI cable †
HDTV †
The Vertical Battery Grip
The optional VG-XT1 vertical battery grip accommodates an extra battery for improved endurance and
makes it easier to hold the camera rotated 90 ° to frame pictures in “tall” (portrait) orientation.
Parts of the VG-XT1
The shooting controls on the VG-XT1 perform the same functions as the controls on the camera.
Technical Notes
A Shutter button
B Control lock
C Front command dial
D Lock screw knob
E Eyelet for camera strap
F Tripod socket
G Connector
H Lock screw
I Compartment for connector cover supplied with camera
J FOCUS ASSIST button
K Rear command dial
L AE-L button
M AF-L button
N DC coupler connector cover
O Battery-chamber cover latch
P Battery-chamber cover
113
The Vertical Battery Grip
Attaching the VG-XT1
The VG-XT1 attaches as shown below.
1 Remove the vertical battery grip connector
cover from the camera and place it in the grip
connector cover compartment.
2 Align the connectors on the grip with the
matching connectors on the camera.
3 Rotate the lock screw knob to tighten the lock
screw.
Inserting a Battery
Insert a battery as shown below.
1 Unlatch and open the battery-chamber cover.
2 Insert the battery.
3 Close and latch the batterychamber cover.
Q The battery in the grip is used before the battery in
the camera. The camera automatically switches to
the camera battery when the battery in the grip is
exhausted. Movie recording and bulb photography
will end when the camera switches batteries. When
the battery in the grip is exhausted, remove and
charge the battery or replace it with a fully-charged
spare battery.
R The camera shows the levels of
both batteries, with the camera
battery level listed first.
AC Power Adapters
The grip can be used with an optional AC-9V AC
power adapter and CP-W126 DC coupler.
114
P
Caring for the Camera
To ensure continued enjoyment of the product, observe the following precautions.
■ Water and Sand
This camera cannot be used under water. Keep
the camera against penetration of garbage, mud,
sand, dust, water, harmful gas, salt, and so on. Do
not place the camera on a wet surface. Make sure
the covers (caps) for the battery, card slot and
ports are securely closed before use. If the camera
is exposed to rain, droplets of water, and so on,
dry it thoroughly.
■ Condensation
Sudden increases in temperature, such as occur
when entering a heated building on a cold day,
can cause condensation inside the camera. If this
occurs, turn the camera off and wait an hour before turning it on again. If condensation forms on
the memory card, remove the card and wait for
the condensation to dissipate.
Technical Notes
Storage and Use
If the camera will not be used for an extended period, remove the battery and memory card. Do
not store or use the camera in locations that are:
• exposed to rain, steam, or smoke
• very humid or extremely dusty
• exposed to direct sunlight or very high temperatures, such as in a closed vehicle on a sunny
day
• extremely cold
• subject to strong vibration
• exposed to strong magnetic fields, such as near
a broadcasting antenna, power line, radar emitter, motor, transformer, or magnet
• in contact with volatile chemicals such as pesticides
• next to rubber or vinyl products
Traveling
Keep the camera in your carry-on baggage.
Checked baggage may suffer violent shocks that
could damage the camera.
115
Cleaning the Image Sensor
Multiple photographs marred by spots or blotches in identical locations may indicate the presence
of dust on the camera image sensor. Clean the sensor using the V SENSOR CLEANING option in
the setup menu (P 92); if the problem persists, you can clean the sensor manually as described below.
Note that there will be a charge to repair or replace the image sensor if it is damaged during cleaning.
1 Use a blower (not a brush) to remove dust from the sensor.
Q Do not use a brush or blower brush. Failure to observe this precaution could damage the sensor.
2 Check whether the dust has been successfully removed.
R Repeat Steps 1 and 2 as necessary.
3 Replace the body cap or lens.
116
Troubleshooting
Problems and Solutions
■ Power and Battery
Problem
The camera does not
turn on.
The monitor does not
turn on.
The battery runs down
quickly.
The battery is exhausted
exhausted:: Charge the battery ((P
P 13) or insert a fully-charged spare battery ((P
P 14).
Reinsert the battery in the correct orientation and make sure that the charger is plugged in ((P
P 13).
Charge the battery at room temperature ((P
P iv).
• There is dirt on the battery terminals
terminals:: Clean the terminals with a soft, dry cloth.
• The battery has been charged many times
times:: The battery has reached the end of its charging life. Purchase a new
battery. If the battery still fails to charge, contact your FUJIFILM dealer.
■ Menus and Displays
Problem
Display is not in English.
Solution
Troubleshooting
The camera turns off
suddenly.
Charging does not start.
Charging is slow.
The charging lamp blinks,
but the battery does not
charge.
Solution
• The battery is exhausted
exhausted:: Charge the battery ((P
P 13) or insert a fully-charged spare battery ((P
P 14).
• The battery is inserted incorrectly:
incorrectly: Reinsert in the correct orientation ((P
P 14).
• The battery-chamber cover is not latched
latched:: Latch the battery-chamber cover ((P
P 14).
The monitor may not turn on if the camera is turned off and then on again very quickly. Press the shutter button
halfway to activate the monitor.
• The battery is cold
cold:: Warm the battery by placing it in a pocket or other warm place and reinsert it in the camera
immediately before taking a picture.
• There is dirt on the battery terminals
terminals:: Clean the terminals with a soft, dry cloth.
• ON is selected for G AUTOFOCUS SETTING > PRE-AF
PRE-AF:: Turn PRE-AF off (P
(P 78).
• The battery has been charged many times
times:: The battery has reached the end of its charging life. Purchase a new
battery.
Select ENGLISH for Q a ((P
P 89).
117
Problems and Solutions
■ Shooting
Problem
No picture is taken when
the shutter button is
pressed.
•
•
•
•
•
•
•
Solution
The memory card is full
full:: Insert a new memory card or delete pictures (P
(P 14, 30).
The memory card is not formatted
formatted:: Format the memory card (P
(P 94).
There is dirt on the memory card contacts
contacts:: Clean the contacts with a soft, dry cloth.
The memory card is damaged
damaged:: Insert a new memory card ((P
P 14).
The battery is exhausted
exhausted:: Charge the battery ((P
P 13) or insert a fully-charged spare battery ((P
P 14).
The camera has turned off automatically:
automatically: Turn the camera on (P
(P 17).
The indicator lamp was orange when you attempted to record a panorama:
panorama: Wait until the indicator lamps turns off
(P 4).
Mottling (“noise”) appears
in the monitor or viewGain is increased to aid composition when the subject is poorly lit and aperture is stopped down, which may result
finder when the shutter in noticeable mottling when images are previewed in the displays. Images taken with the camera are unaffected.
button is pressed halfway.
• The subject is close to the camera
camera:: Select macro mode (P
(P 41), if available. If macro mode is unavailable, choose a
different shooting mode.
The camera does not focus.
• The subject is far away from the camera
camera:: Cancel macro mode ((P
P 41).
• The subject is not suited to autofocus
autofocus:: Use focus lock ((P
P 67) or manual focus (P
(P 61).
Intelligent Face Detection
Intelligent Face Detection is not available in the current shooting mode:
mode: Choose a different shooting mode.
is not available.
• The subject’s face is obscured by sunglasses, a hat, long hair, or other objects
objects:: Remove the obstructions.
• The subject’s face occupies only a small area of the frame
frame:: Change the composition so that the subject’s face occupies a larger area of the frame ((P
P 67).
No face is detected.
• The subject’s head is tilted or horizontal
horizontal:: Ask the subject to hold their head straight.
• The camera is tilted
tilted:: Keep the camera level.
• The subject’s face is poorly lit
lit:: Shoot in bright light.
The selected subject is closer to the center of the frame than the main subject. Recompose the picture or turn face
Wrong subject is selected.
detection off and frame the picture using focus lock (P
(P 67).
118
Problems and Solutions
Problem
The flash does not fire.
•
•
•
•
•
•
Solution
The flash can not be used at current settings
settings:: See the list of the settings that can be used with the flash.
The flash is lowered
lowered:: Raise the flash (P
(P 36).
The DRIVE dial is rotated to BKT, CH, or CL
CL:: Rotate the dial to S ((P
P 54, 56).
The battery is exhausted
exhausted:: Charge the battery ((P
P 13) or insert a fully-charged spare battery ((P
P 14).
The camera is in bracketing or continuous mode
mode:: Select single frame mode.
The camera is in silent mode
mode:: Turn silent mode off (P
(P 89).
Troubleshooting
Some flash modes are not
The camera is in silent mode. Turn silent mode off (P
(P 89).
available.
• The subject is not in range of the flash
ash:: Position the subject in range of the flash ((P
P 127).
The flash does not fully
• The flash window is obstructed
obstructed:: Hold the camera correctly ((P
P 25).
light the subject.
• Shutter speed is faster than 1/180 ss:: Choose a slower shutter speed ((P
P 37, 47, 49).
• The lens is dirty
dirty:: Clean the lens ((P
P xi).
• The lens is blocked
blocked:: Keep objects away from the lens.
Pictures are blurred.
• s is displayed during shooting and the focus frame is displayed in red:
red: Check focus before shooting ((P
P 25).
• k is displayed during shooting:
shooting: Use the flash or mount the camera on a tripod ((P
P 36).
• Shutter speed is slow and the ambient temperature is high:
high: This is normal and does not indicate a malfunction.
Pictures are mottled.
• The camera has been used continuously at high temperatures or a temperature warning is displayed
displayed:: Turn the camera off and wait for it to cool down.
119
Problems and Solutions
■ Playback
Problem
Solution
Pictures are grainy.
The pictures were taken with a different make or model of camera.
Playback zoom is unavailThe pictures were created using O RESIZE or with a different make or model of camera.
able.
• Playback volume is too low:
low: Adjust playback volume (P
(P 90).
No sound in movie
• The microphone was obstructed
obstructed:: Hold the camera correctly during recording ((P
P 2, 31).
playback.
• The speaker is obstructed
obstructed:: Hold the camera correctly during playback ((P
P 2, 33).
• The camera is in silent mode
mode:: Turn silent mode off (P
(P 89).
Selected pictures are not Some of the pictures selected for deletion are protected. Remove protection using the device with which it was
deleted.
originally applied (P
(P 84).
File numbering is unexThe battery-chamber cover was opened while the camera was on. Turn the camera off before opening the batpectedly reset.
tery-chamber cover ((P
P 14, 17).
■ Connections/Miscellaneous
For additional information on troubleshooting wireless connections, visit:
http://faq.fujifilm.com/digitalcamera/faq_product.html?pid=F
Problem
Problem connecting or
uploading pictures to
smartphone.
Can not upload images.
Smartphone will not
display pictures.
120
Solution
• The smartphone is too far away:
away: Move the devices closer.
• Nearby devices are causing radio interference
interference:: Move the camera and smartphone away from microwave ovens or
cordless phones.
• The smartphone is connected to another device
device:: The smartphone and camera can connect to only one device at a
time. End the connection and try again.
• There are several smartphones in the vicinity
vicinity:: Try connecting again. The presence of multiple smartphones can
make connection difficult.
• The current image is a movie or was created on another device and can not be uploaded to a smartphone.
Select ON for r WIRELESS SETTING >
SETTING > RESIZE IMAGE FOR SMARTPHONE H. Selecting OFF increases
upload times for larger images; in addition, some phones may not display images over a certain size.
Problems and Solutions
Problem
Solution
• The camera is not properly connected:
connected: Connect the camera properly (P
(P 108).). Note that once the camera is connected, pictures will be displayed on the TV instead of in the camera monitor.
No picture or sound on TV.
• Input on the television is set to “TV”:
“TV”: Set input to “HDMI”.
• The volume on the TV is too low:
low: Use the controls on the television to adjust the volume.
The computer does not
Be sure the camera and computer are correctly connected ((P
P 101).).
recognize the camera.
Can not transfer RAW or
Use the bundled software to transfer pictures ((P
P 98).).
JPEG files to computer.
Pictures can not be
• The camera is not properly connected
connected:: Connect the camera correctly ((P
P 103).).
printed.
• The printer is off: Turn the printer on.
Only one copy is printed/
The printer is not PictBridge compatible.
the date is not printed.
The camera is unrespon- • Temporary camera malfunction:
malfunction: Remove and reinsert the battery ((P
P 14).
sive.
• The battery is exhausted
exhausted:: Charge the battery ((P
P 13) or insert a fully-charged spare battery ((P
P 14).
The camera does not funcRemove and reinsert the battery ((P
P 14). If the problem persists, contact your FUJIFILM dealer.
tion as expected.
No sound.
Turn silent mode off ((P
P 89).
Troubleshooting
121
Warning Messages and Displays
The following warnings appear in the display.
Warning
B (red)
A (blinks red)
k
s
(displayed in red with
red focus frame)
Aperture or shutter speed
displayed in red
FOCUS ERROR
TURN OFF THE CAMERA
AND TURN ON AGAIN
LENS CONTROL ERROR
LENS ERROR
BUSY
CARD NOT INITIALIZED
PROTECTED CARD
122
Description
Low battery. Charge the battery ((P
P 13) or insert a fully-charged spare battery ((P
P 14).
Battery exhausted. Charge the battery ((P
P 13) or insert a fully-charged spare battery ((P
P 14).
Slow shutter speed. Pictures may be blurred; use the flash or a tripod.
The camera can not focus. Try one of the following solutions:
• Use focus lock to focus on another subject at the same distance, then recompose the picture ((P
P 67).
• Use macro mode to focus when taking close-ups.
The subject is too bright or too dark and the picture will be over- or under-exposed. Use the flash for additional
lighting when taking photographs of poorly-lit subjects.
Camera malfunction. Turn the camera off and then on again. If the message persists, contact a FUJIFILM dealer.
Turn the camera off, remove the lens, and clean the mounting surfaces, then replace the lens and turn the camera
on. If the problem persists, contact a FUJIFILM dealer.
The memory card is incorrectly formatted. Use the camera to format the card ((P
P 94).
• The memory card is not formatted or the memory card has been formatted in a computer or other device
device:: Format the
memory card using the K FORMAT option in the camera setup menu ((P
P 94).
• The memory card contacts require cleaning
cleaning:: Clean the contacts with a soft, dry cloth. If the message is repeated,
format the card (P
(P 94). If the message persists, replace the card.
• Camera malfunction:
malfunction: Contact a FUJIFILM dealer.
The memory card is locked. Unlock the card.
Warning Messages and Display
Warning
CARD ERROR
b MEMORY FULL
NO CARD
WRITE ERROR
READ ERROR
TOO MANY FRAMES
Troubleshooting
FRAME NO. FULL
Description
• The memory card is not formatted for use in the camera
camera:: Format the card (P
(P 94).
• The memory card contacts require cleaning or the memory card is damaged
damaged:: Clean the contacts with a soft, dry
cloth. If the message is repeated, format the card (P
(P 94). If the message persists, replace the card.
• Incompatible memory card:
card: Use a compatible card ((P
P 16).
• Camera malfunction:
malfunction: Contact a FUJIFILM dealer.
The memory card is full and pictures can not be recorded. Delete pictures (P
(P 30) or insert a memory card with
more free space ((P
P 14).
The shutter can only be released when a memory card is inserted. Insert a memory card.
• Memory card error or connection error:
error: Reinsert the card or turn the camera off and then on again. If the message
persists, contact a FUJIFILM dealer.
• Not enough memory remaining to record additional pictures
pictures:: Delete pictures (P
(P 30) or insert a memory card with
more free space ((P
P 14).
• The memory card is not formatted
formatted:: Format the memory card (P
(P 94).
• The file is corrupt or was not created with the camera
camera:: The file can not be viewed.
• The memory card contacts require cleaning
cleaning:: Clean the contacts with a soft, dry cloth. If the message is repeated,
format the card (P
(P 94). If the message persists, replace the card.
• Camera malfunction:
malfunction: Contact a FUJIFILM dealer.
The camera has run out of frame numbers (current frame number is 999-9999). Format the memory card and
select RENEW for FRAME NO.
NO..Take
.Take a picture to reset frame numbering to 100-0001, then select CONTINUOUS for FRAME NO.
NO...
• A search has returned more than 30,000 results:
results: Choose a search that returns fewer results.
• More than 999 images are selected for deletion
deletion:: Choose fewer images.
123
Warning Messages and Display
Warning
PROTECTED FRAME
CAN NOT CROP
m CANNOT EXECUTE
F CANNOT EXECUTE
CAN NOT ROTATE
F CAN NOT ROTATE
Description
An attempt was made to delete or rotate to a protected picture. Remove protection and try again ((P
P 84).
The picture is damaged or was not created with the camera.
Red-eye removal can not be applied to pictures created with other devices.
Red-eye removal can not be applied to movies.
The selected picture can not be rotated.
Movies can not be rotated.
The DPOF print order on the current memory card contains more than 999 images. Copy the pictures to a comDPOF FILE ERROR
puter and create a new print order.
The picture can not be printed using DPOF.
CAN NOT SET DPOF
F CAN NOT SET DPOF Movies can not be printed using DPOF.
A connection error occurred while pictures were being printed or copied to a computer or other device. Confirm
COMMUNICATION ERROR
that the device is turned on and that the USB cable is connected.
Printer out of paper or ink, or other printer error. Check printer (see printer manual for details). To resume printing,
PRINTER ERROR
turn the printer off and then turn it back on.
Printer out of paper or ink, or other printer error. Check printer (see printer manual for details). If printing does not
PRINTER ERROR
resume automatically, press MENU/OK to resume.
RESUME?
An attempt was made to print a movie, a picture not created with the camera, or a picture in a format not supported by the printer. Movies, RAW images, and some pictures created with other devices can not be printed; if
CANNOT BE PRINTED
the picture is a still picture created with the camera, check the printer manual to confirm that the printer supports
the JFIF-JPEG or Exif-JPEG format. If it does not, the pictures can not be printed.
Turn the camera off and wait for it to cool. Mottling may increase in pictures taken when this warning is displayed.
p
124
Appendix
Memory Card Capacity
The following table shows the recording time or number of pictures available at different image sizes.
All figures are approximate; file size varies with the scene recorded, producing wide variations in the
number of files that can be stored. The number of exposures or length remaining may not diminish
at an even rate.
4 GB
Capacity
O
T FINE
600
O3:2
Photographs
RAW
120
i 1920×1080 60 fps 2
13 min.
i 1920×1080 30 fps 2
Movies 1
3
h 1280×720 60 fps
25 min.
h 1280×720 30 fps 3
1 Use a H card or better.
2 Individual movies can not exceed 14 minutes in length.
3 Individual movies can not exceed 27 minutes in length.
8 GB
T NORMAL
960
T FINE
1210
T NORMAL
1910
230
26 min.
51 min.
Appendix
125
Specifications
System
Model
Effective pixels
Image sensor
Storage media
File system
File format
Image size
Lens mount
Sensitivity
Metering
Exposure control
Exposure compensation
Shutter speed
(mechanical shutter)
126
FUJIFILM X-T1 digital camera
16.3 million
23.6 mm × 15.6 mm (APS-C), X-Trans CMOS II sensor with square pixels and primary color filter
FUJIFILM-recommended SD/SDHC/SDXC memory cards
Compliant with Design Rule for Camera File System (DCF)
(DCF),, Exif 2.3, and Digital Print Order Format (DPOF)
• Still pictures:
pictures: Exif 2.3 JPEG (compressed)
(compressed);; RAW (original RAF format, special-purpose software required)
required);; RAW+JPG available
• Movies
Movies:: H.264 standard with stereo sound (MOV)
• O 3 : 2:
2: 4,896 × 3,264
• O 16 : 9:
9: 4,896 × 2,760
• O 1 : 1:
1: 3,264 × 3,264
• P 3 : 2:
2: 3,456 × 2,304
• P 16 : 9:
9: 3,456 × 1,944
• P 1 : 1:
1: 2,304 × 2,304
• Q 3 : 2:
2: 2,496 × 1,664
• Q 16 : 9:
9: 2,496 × 1,408
• Q 1 : 1:
1: 1,664 × 1,664
• O panorama
panorama:: 2,160 × 9,600 (vertical) / 9,600 × 1,440 (horizontal)
• P panorama
panorama:: 2,160 × 6,400 (vertical) / 6,400 × 1,440 (horizontal)
FUJIFILM X mount
Standard output sensitivity equivalent to ISO 200 – 6400 in increments of / EV; AUTO; extended output sensitivity
equivalent to ISO 100, 12800, 25600, or 51200
256-segment throughhrough-tthehe-llens (TTL) metering; MULTI, SPOT, AVERAGE
Programmed AE (with program shift)
shift);; shutter-priority AE; aperture-priority AE; manual exposure
–3 EV – +3 EV in increments of / EV
• P mode
mode:: / sec. to / sec.
• Time
Time:: 30 sec. to 2 sec.
• Bulb
Bulb:: Max. 60 min.
• All other modes:
modes: 30 sec. to / sec.
Specifications
System
Continuous
Mode
I
Focus
White balance
Self-timer
Flash mode
Hot shoe
Viewfinder
Frame rate (fps)
8.0
3.0
Frames per burst
Up to approximately 47
Until card is full
R The frame rate and number of frames per burst may vary depending on the type of memory card
used.
R The frame rate varies with shooting conditions and the number of images recorded.
• Mode
Mode:: Single or continuous AF; manual focus with focus ring
• Focus-area selection
selection:: Multi, area with focus area size selection; 49 (7 × 7) areas available in viewfinder and LCD
monitor
• Autofocus system:
system: Intelligent hybrid AF (TTL contrast-detect/phase-detection AF) with AF-assist illuminator
Custom, color temperature selection, auto, direct sunlight, shade, daylight fluorescent, warm white fluorescent,
cool white fluorescent, incandescent, underwater
Off, 2 sec., 10 sec.
Auto, fill flash, off, slow sync, rear-curtain sync, commander (red-eye removal off );); auto with red-eye removal, fill flash
with red-eye removal,
removal, off, slow
slow sync with red-eye removal, rear-curtain sync with red-eye removal, commander
(red-eye removal on)
Accessory shoe with TTL contacts
0.5-in., 2,360k-dot color OLED viewfinder with diopter adjustment (–4 to +2 m–1); magnification 0.77 × with
50 mm lens (35 mm format equivalent) at infinity and diopter set to –1.0 m–1; diagonal angle of view approximately 38° (horizontal angle of view approximately 31°); eye point approx. 23 mm; frame coverage approx. 100%
3.0-in/7.6 cm., 1,040k-dot color LCD monitor; frame coverage approx. 100%, tilting
• i 1920 × 1080 60fps:
60fps: Frame size 1,920 × 1,080 (1080p); 60 fps; stereo sound
• i 1920 × 1080 30fps:
30fps: Frame size 1,920 × 1,080 (1080p); 30 fps; stereo sound
• h 1280 × 720 60fps:
60fps: Frame size 1,280 × 720 (720p); 60 fps; stereo sound
• h 1280 × 720 30fps:
30fps: Frame size 1,280 × 720 (720p); 30 fps; stereo sound
Appendix
LCD monitor
Movies
J
O
127
Specifications
Input/output terminals
HDMI output
HDMI mini connector
Digital input/output
USB 2.0 High-Speed
Microphone/
φ2.5 mm mini-stereo jack
remote release connector
Power supply/other
Power supply
Battery life (approximate
number of frames that can
be taken with a fully-charged
battery, XF 35 mm f/1.4 R
lens, LCD monitor/viewfinder
on, and supplied flash not
attached)
Camera size (W × H × D)
Camera weight
Shooting weight
Operating conditions
Wireless transmitter
Standards
Operating frequency
Access protocols
128
NP-W126 rechargeable battery
Battery type
NP-W126 (type supplied with camera)
Approximate number of frames
350
CIPA standard, measured using battery supplied with camera and SD memory card.
Note: Number of shots that can be taken with battery varies with battery charge level and will decline at low
Note:
temperatures.
129.0 mm × 89.8 mm × 46.7 mm (33.4
(33.4 mm excluding projections, measured at thinnest part)/5.0
part)/5.0 in. × 3.5 in. × 1.8 in. (1.3 in.)
Approx. 390 g/13.7 oz., excluding battery, accessories, and memory card
Approx. 440 g/15.5 oz., including battery and memory card
• Temperature
Temperature:: -10 °C to +40 °C/+14 °F to +104 °F
• Humidity
Humidity:: 10% – 80% (no condensation)
IEEE 802.11b/g/n (standard wireless protocol)
• U. S. A., Canada, Taiwan:
Taiwan: 2,412 MHz–2,462 MHz (11 channels)
• Other countries:
countries: 2,412 MHz–2,472 MHz (13 channels)
Infrastructure
Specifications
EF-X8 shoe-mounted flash unit
Guide number
GN8 (ISO100), GN11 (ISO200)
Dimensions (W × H × D) 39.7 mm × 24.2 mm × 63.4 mm/1.5 in. × 0.9 in. × 2.4 in., excluding projections
Weight
Approx. 41 g/1.4 oz.
NP-W126 rechargeable battery
Nominal voltage
7.2 V DC
Nominal capacity
1,260 mAh
Operating temperature 0 °C to +40 °C/+32 °F to +104 °F
Dimensions (W × H × D) 36.4 mm × 47.1 mm × 15.7 mm/1.4 in. × 1.8 in. × 0.6 in.
Weight
Approx. 47 g/1.7 oz.
BC-W126 battery charger
Rated input
Input capacity
Rated output
Supported batteries
Charging time
Operating temperature
Dimensions (W × H × D)
Weight
100 V – 240 V AC, 50/60 Hz
13 –21 VA
8.4 V DC, 0.6 A
NP-W126 rechargeable batteries
Approx. 150 minutes (+20 °C/+68 °F)
5 °C to +40 °C/+41 °F to +104 °F
65 mm × 91.5 mm × 28 mm/2.5 in. × 3.6 in. × 1.1 in., excluding projections
Approx. 77 g/2.7 oz., excluding battery
Appendix
Weight and dimensions vary with the country or region of sale. Labels, menus, and other displays may differ from those on the
actual camera.
129
Specifications
■ Notices
• Specifications subject to change without notice; for the latest information, visit http://www.fujifilm.com/products/
digital_cameras/index.html. FUJIFILM shall not be held liable for damages resulting from errors in this manual.
• Although the viewfinder and LCD monitor are manufactured using advanced high-precision technology, small
bright points and anomalous colors may appear, particularly in the vicinity of text. This is normal for this type of
LCD display and does not indicate a malfunction; images recorded with the camera are unaffected.
• Digital cameras may malfunction when exposed to strong radio interference (e.g., electric fields, static electricity,
or line noise).
• Due to the type of lens used, some distortion may occur at the periphery of images. This is normal.
130
Restrictions on Camera Settings
The options available in each shooting mode are listed below.
Option
Focus mode (selector)
S
C
M
Exposure compensation (dial)
ISO (dial)
Photometry (dial)
H1/H2
1000 — 6400
200 — 800
L (100)
AUTO
o
p
q
P
S
A
M
BKT
CH/CL
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔2
✔2
✔
✔2
✔2
✔
✔
✔
✔
✔
✔
✔
✔2
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
DRIVE dial
j ADV.
✔
✔
✔
✔2
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔5
✔5
✔2
✔9
✔9
✔
✔9
✔
✔
u
✔
✔
✔
✔2
✔7
✔
✔
✔7
✔
✔
Button
F
✔
✔
✔
✔
✔
Appendix
131
Restrictions on Camera Settings
Option
G AUTOFOCUS SETTING
A
M
BKT
CH/CL
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
s
✔
✔
✔
✔
✔
✔
✔
t
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔2
✔2
✔2
✔2
✔2
✔2
✔2
✔2
✔
✔
✔
✔2
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔6
✔6
✔
FACE DETECTION
PRE-AF
AF ILLUMINATOR
O IMAGE SIZE
T IMAGE QUALITY
U DYNAMIC RANGE
P FILM SIMULATION
B SELF-TIMER
o INTERVAL TIMER SHOOTING
D WHITE BALANCE
132
S
MACRO
RELEASE/FOCUS PRIORITY
INSTANT AF SETTING
AF MODE
DRIVE dial
j ADV.
P
O
P
Q
FINE
NORMAL
FINE+RAW
NORMAL+RAW
RAW
AUTO
V
W
X
u
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Button
F
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔8
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Restrictions on Camera Settings
Option
f COLOR
q SHARPNESS
r HIGHLIGHT TONE
s SHADOW TONE
h NOISE REDUCTION
K LONG EXPOSURE NR
j LENS MODULATION OPTIMIZER
u SELECT CUSTOM SETTING
K EDIT/SAVE CUSTOM SETTING
c MF ASSIST
STANDARD
DIGITAL SPLIT IMAGE
FOCUS PEAK HIGHLIGHT
v AE/AF-LOCK MODE
d AF-LOCK MODE
p FLASH MODE
I FLASH COMPENSATION
B RED EYE REMOVAL
Q/K
N/L
F/M
l/d
D
P
P
S
A
M
BKT
CH/CL
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
DRIVE dial
j ADV.
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
u
Button
F
✔
✔8
✔
✔
✔2
✔
✔2
✔
✔
✔
✔
✔
✔
✔
✔2
✔
✔2
✔
✔
✔
✔
✔
✔
✔
Appendix
133
Restrictions on Camera Settings
Option
IMAGE DISP.
PREVIEW EXP. IN MANUAL MODE
FOCUS CHECK
FOCUS SCALE UNITS
A SCREEN SET-UP
DISP. CUSTOM SETTING
FRAMING GUIDELINE
ELECTRONIC LEVEL
AF DISTANCE INDICATOR
MF DISTANCE INDICATOR
HISTOGRAM
APERTURE/S-SPEED/ISO
EXP. COMPENSATION
PHOTOMETRY
FLASH
WHITE BALANCE
FILM SIMULATION
DYNAMIC RANGE
FRAMES REMAINING
BATTERY LEVEL
IMAGE SIZE/QUALITY
J COLOR SPACE
1
2
3
4
134
Not available (grayed out).
Changes have no effect.
Center focus area selected automatically.
Options available vary with shooting mode.
Manual exposure mode only.
sRGB selected automatically.
P
S
A
M
BKT
CH/CL
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔3
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔3
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
DRIVE dial
j ADV.
✔
✔3
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
5 Functions in mode S.
6 Number of shots per burst restricted.
7 ISO 200 selected automatically.
8 Fixed automatically.
9 AUTO selected automatically.
✔
✔3
u
Button
F
✔
✔3
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔4
Memo
135
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN
http://www.fujifilm.com/products/digital_cameras/index.html
Download PDF

advertising