FujiFilm 16228991 Camcorder Owner's Manual

BL01758-200
DIGITAL CAMERA
XF1
Owner’s Manual
Thank you for your purchase
of this product. This manual
describes how to use your
FUJIFILM digital camera and the
supplied software. Be sure that
you have read and understood
its contents and the warnings in
“For Your Safety” (P ii) before using the camera.
For information on related products, visit our website at
http://www.fujifilm.com/products/digital_cameras/index.html
EN
Before You Begin
First Steps
Basic Photography and Playback
More on Photography
More on Playback
Movies
Connections
Menus
Technical Notes
Troubleshooting
Appendix
For Your Safety
IMPORTANT SAFETY INSTRUCTIONS
• Read Instructions: All the safety and operating instructions should be read before the
appliance is operated.
• Retain Instructions: The safety and operating
instructions should be retained for future
reference.
• Heed Warnings: All warnings on the appliance and in the operating instructions
should be adhered to.
• Follow Instructions: All operating and use
instructions should be followed.
Installation
Power Sources: This video product should be
operated only from the type of power source
indicated on the marking label. If you are
not sure of the type of power supply to your
home, consult your appliance dealer or local
power company. For video products intended to operate from battery power, or other
sources, refer to the operating instructions.
Grounding or Polarization: This video product
is equipped with a polarized alternatingcurrent line plug (a plug having one blade
wider than the other). This plug will fit into
the power outlet only one way. This is a safety
feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If
the plug should still fail to fit, contact your
electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
ii
Alternate Warnings: This video product is
equipped with a three-wire grounding-type
plug, a plug having a third (grounding) pin.
This plug will only fit into a grounding-type
power outlet. This is a safety feature. If you
are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose
of the grounding type plug.
Overloading: Do not overload wall outlets and
extension cords as this can result in a risk of
fire or electric shock.
Power-Cord Protection: Power-supply cords
should be routed so that they are not likely
to be walked on or pinched by items placed
upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the point where they exit from
the appliance.
Accessories: Do not place this video product
on an unstable cart, stand, tripod, bracket, or
table. The video product may fall, causing
serious injury to a child or adult, and serious
damage to the appliance. Use only with a
cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with
the video product. Any mounting of the appliance should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
Ventilation: Slots and openings in the cabinet
are provided for ventilation, to ensure reliable
operation of the video product and to protect it from overheating, and these openings
must not be blocked or covered. The openings should never be blocked by placing the
video product on a bed, sofa, rug, or other An appliance and cart
combination should
similar surface.
be moved with care.
This video product should not be placed in a
Quick stops, excesbuilt-in installation such as a bookcase or rack
sive force, and uneven
unless proper ventilation is provided or the
surfaces may cause
manufacturer’s instructions have been adthe appliance and cart
hered to. This video product should never be
combination to overturn.
placed near or over a radiator or heat register.
Attachments: Do not use attachments not
recommended by the video product manufacturer as they may cause hazards.
Water and Moisture: Do not use this video
product near water—for example, near a
bath tub, wash bowl, kitchen sink, or laundry
tub, in a wet basement, or near a swimming
pool, and the like.
For Your Safety
Antennas
Outdoor Antenna Grounding: If an outside
antenna or cable system is connected to the
video product, be sure the antenna or cable
system is grounded so as to provide some
protection against voltage surges and builtup static charges. Section 810 of the National
Electrical Code, ANSI/NFPA No. 70, provides
information with respect to proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
Ground Clamp
Antenna Lead
in Wire
Electric Service
Equipment
Antenna
Discharge Unit
(NEC SECTION
810-20)
Ground Clamps
Power Service Grounding
Electrode System (NEC ART
250. PART H)
Grounding
Conductors
(NEC SECTION
810-21)
Power Lines: An outside antenna system
should not be located in the vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such
power lines or circuits. When installing an
outside antenna system, extreme care should
be taken to keep from touching such power
lines or circuits as contact with them might
be fatal.
mally follow the operating instructions. Adjust only those controls that are covered by
the operating instructions as an improper
adjustment of other controls may result in
damage and will often require extensive work
by a qualified technician to restore the video
Object and Liquid Entry: Never push objects product to its normal operation.
of any kind into this video product through
openings as they may touch dangerous volt- When the video product exhibits a distinct
age points or short out parts that could result change in performance—this indicates a
in a fire or electric shock. Never spill liquid of need for service.
Use
Cleaning: Unplug this video product from the
wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
any kind on the video product.
Lightning: For added protection for this video
product receiver during a lightning storm, or
when it is left unattended and unused for
long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable
system. This will prevent damage to the
video product due to lightning and powerline surges.
Replacement Parts: When replacement parts
are required, be sure the service technician
has used replacement parts specified by the
manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or
other hazards.
Safety Check: Upon completion of any service
or repairs to this video product, ask the service technician to perform safety checks to
Service
determine that the video product is in proper
Servicing: Do not attempt to service this video operating condition.
product yourself as opening or removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified
service personnel.
Damage Requiring Service: Unplug this video
product from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
• When the power-supply cord or plug is
damaged.
• If liquid has been spilled, or objects have
fallen into the video product.
• If the video product has been exposed to
rain or water.
• If the video product has been dropped or
the cabinet has been damaged.
If the video product does not operate nor-
iii
For Your Safety
Be sure to read these notes before use
WARNING
Safety Notes
• Make sure that you use your camera correctly. Read these safety
notes and your Owner’s Manual carefully before use.
• After reading these safety notes, store them in a safe place.
About the Icons
The icons shown below are used in this document to indicate the
severity of the injury or damage that can result if the information
indicated by the icon is ignored and the product is used incorrectly
as a result.
WARNING
CAUTION
This icon indicates that death or serious injury can result if the
information is ignored.
This icon indicates that personal injury or material damage can
result if the information is ignored.
The icons shown below are used to indicate the nature of the instructions which are to be observed.
Triangular icons tell you that this information requires attention (“Important”).
Circular icons with a diagonal bar tell you that the action indicated is prohibited (“Prohibited”).
Filled circles with an exclamation mark indicate an action that
must be performed (“Required”).
WARNING
Unplug from
power socket
Avoid exposure
to water
iv
If a problem arises, turn the camera off, remove the battery, and
disconnect and unplug the AC power adapter. Continued use of
the camera when it is emitting smoke, is emitting any unusual
odor, or is in any other abnormal state can cause a fire or electric shock. Contact your FUJIFILM dealer.
Do not allow water or foreign objects to enter the camera. If water
or foreign objects get inside the camera, turn the camera off,
remove the battery, and disconnect and unplug the AC power
adapter. Continued use of the camera can cause a fire or electric shock. Contact your FUJIFILM dealer.
Do not use in
the bathroom or
shower
Do not
disassemble
Do not touch
internal parts
Do not use the camera in the bathroom or shower. This can cause
a fire or electric shock.
Never attempt to change or take apart the camera (never open
the case). Failure to observe this precaution can cause fire or
electric shock.
Should the case break open as the result of a fall or other accident,
do not touch the exposed parts. Failure to observe this precaution could result in electric shock or in injury from touching the
damaged parts. Remove the battery immediately, taking care
to avoid injury or electric shock, and take the product to the
point of purchase for consultation.
Do not change, heat or unduly twist or pull the connection cord and
do not place heavy objects on the connection cord. These actions
could damage the cord and cause a fire or electric shock. If the
cord is damaged, contact your FUJIFILM dealer.
Do not place the camera on an unstable surface. This can cause the
camera to fall or tip over and cause injury.
Never attempt to take pictures while in motion. Do not use the
camera while you are walking or driving a vehicle. This can result in you falling down or being involved in a traffic accident.
Do not touch any metal parts of the camera during a thunderstorm.
This can cause an electric shock due to induced current from
the lightning discharge.
Do not use the battery except as specified. Load the battery as
shown by the indicator.
Do not heat, change or take apart the battery. Do not drop or subject
the battery to impacts. Do not store the battery with metallic products. Any of these actions can cause the battery to burst or leak
and cause fire or injury as a result.
Use only the battery or AC power adapters specified for use with this
camera. Do not use voltages other than the power supply voltage
shown. The use of other power sources can cause a fire.
If the battery leaks and fluid gets in contact with your eyes, skin or
clothing, flush the affected area with clean water and seek medical
attention or call an emergency number right away.
For Your Safety
WARNING
CAUTION
Do not use the charger to charge batteries other than those specified
here. The supplied battery charger is for use only with the type of
battery supplied with the camera. Using the charger to charge
conventional batteries or other types of rechargeable batteries
can cause the battery to leak fluid, overheat or burst.
Do not place heavy objects on the camera. This can cause the
heavy object to tip over or fall and cause injury.
Do not move the camera while the AC power adapter is still connected. Do not pull on the connection cord to disconnect the AC power
adapter. This can damage the power cord or cables and cause
a fire or electric shock.
Do not use the AC power adapter when the plug is damaged or the
plug socket connection is loose. This could cause a fire or electric
shock.
Do not cover or wrap the camera or the AC power adapter in a cloth
or blanket. This can cause heat to build up and distort the casing or cause a fire.
When you are cleaning the camera or you do not plan to use the
camera for an extended period, remove the battery and disconnect
and unplug the AC power adapter. Failure to do so can cause a
fire or electric shock.
Danger of explosion if battery is incorrectly replaced. Replace only
with the same or equivalent type.
Do not use in the presence of flammable objects, explosive gases,
or dust.
When carrying the battery, install it in a digital camera or keep it
in the hard case. When storing the battery, keep it in the hard case.
When discarding, cover the battery terminals with insulation tape.
Contact with other metallic objects or batteries could cause
the battery to ignite or burst.
Keep memory cards out of the reach of small children. Because
memory cards are small, they can be swallowed by children.
Be sure to store memory cards out of the reach of small children. If a child swallows a memory card, seek medical attention or call an emergency number.
Turn the camera off in crowds. The camera emits radio-frequency
radiation that may interfere with pacemakers.
Turn the camera off in the vicinity of automatic doors, public address
systems, and other automatically controlled devices. The camera
emits radio-frequency radiation that may cause these devices
to malfunction.
Keep the camera at least 22 cm away from people wearing pacemakers. The camera emits radio-frequency radiation that may
interfere with pacemakers.
CAUTION
Unplug from
power socket
When charging ends, unplug the charger from the power socket.
Leaving the charger plugged into the power socket can cause
a fire.
Using a flash too close to a person’s eyes may temporarily affect the
eyesight. Take particular care when photographing infants and
young children.
When a memory card is removed, the card could come out of the slot
too quickly. Use your finger to hold it and gently release the card.
Injury could result to those struck by the ejected card.
Request regular internal testing and cleaning for your camera.
Build-up of dust in your camera can cause a fire or electric
shock. Contact your FUJIFILM dealer to request internal cleaning every two years. Please note that this service is not free
of charge.
Do not use this camera in locations affected by oil fumes, steam, humidity or dust. This can cause a fire or electric shock.
Remove your fingers from the flash window before the flash fires.
Failure to observe this precaution could result in burns.
Do not leave this camera in places subject to extremely high temperatures. Do not leave the camera in locations such as a sealed
vehicle or in direct sunlight. This can cause a fire.
Keep the flash window clean and do not use the flash if the window
is obstructed. Failure to observe these precautions could cause
smoke or discoloration.
Keep out of the reach of small children. This product could cause
injury in the hands of a child.
v
For Your Safety
■ Charging the Battery
Charge the battery in the supplied battery
charger. Charging times will increase at ambient temperatures below +10 °C (+50 °F) or
above +35 °C (+95 °F). Do not attempt to
The following describes the proper use of charge the battery at temperatures above
batteries and how to prolong their life. Incor- 40 °C (+104 °F); at temperatures below 0 °C
rect use can shorten battery life or cause leak- (+32 °F), the battery will not charge.
age, overheating, fire, or explosion.
Do not attempt to recharge a fully charged
Li-ion Batteries
battery. The battery does not however need
Read this section if your camera uses a to be fully discharged before charging.
rechargeable Li-ion battery.
The battery may be warm to the touch immeThe battery is not charged at shipment. diately after charging or use. This is normal.
Charge the battery before use. Keep the bat- ■ Battery Life
tery in its case when not in use.
At normal temperatures, the battery can be
recharged about 300 times. A noticeable de■ Notes on the Battery
The battery gradually loses its charge when crease in the length of time the battery will
not in use. Charge the battery one or two hold a charge indicates that it has reached
the end of its service life and should be redays before use.
placed.
Battery life can be extended by turning the
■ Storage
camera off when not in use.
Performance may be impaired if the battery is
Battery capacity decreases at low tempera- left unused for extended periods when fully
tures; a depleted battery may not function at charged. Run the battery flat before storing it.
when cold. Keep a fully charged spare battery in a warm place and exchange as nec- If the camera will not be used for an extended
essary, or keep the battery in your pocket or period, remove the battery and store it in a
other warm place and insert it in the camera dry place with an ambient temperature of
only when shooting. Do not place the bat- from +15 °C to +25 °C (+59 °F to +77 °F). Do
tery in direct contact with hand warmers or not store in locations exposed to extremes of
temperature.
other heating devices.
The Battery and Power Supply
Note: Check the type of battery used in
your camera and read the appropriate
sections.
vi
■ Cautions: Handling the Battery
• Do not transport or store with metal objects
such as necklaces or hairpins.
• Do not expose to flame or heat.
• Do not disassemble or modify.
• Use with designated chargers only.
• Do not drop or subject to strong physical
shocks.
• Do not expose to water.
• Keep the terminals clean.
• The battery and camera body may become
warm to the touch after extended use. This
is normal.
AA Alkaline/Rechargeable Ni-MH Batteries
Read this section if your camera uses AA
alkaline or rechargeable AA Ni-MH batteries. Information on compatible battery
types may be found elsewhere in the camera
manual.
■ Cautions: Handling the Batteries
• Do not expose to water, flame, or heat, or
store in warm or humid conditions.
• Do not transport or store with metal objects
such as necklaces or hairpins.
• Do not disassemble or modify the batteries
or battery casing.
• Do not subject to strong physical shocks.
• Do not use batteries that are leaking, deformed, or discolored.
• Keep out of reach of infants and small children.
• Insert in the correct orientation.
For Your Safety
• Do not mix old and new batteries, batteries
with different charge levels, or batteries of
different types.
• If the camera will not be used for an extended period, remove the batteries. Note that
the camera clock will be reset.
• The batteries may be warm to the touch
immediately after use. Turn the camera
off and allow the batteries to cool before
handling.
• Battery capacity tends to decrease at low
temperatures. Keep spare batteries in a
pocket or other warm place and exchange
as necessary. Cold batteries may recover
some of their charge when warmed.
• Fingerprints and other stains on the battery
terminals can impair battery performance.
Thoroughly clean the terminals with a
soft, dry cloth before inserting them in the
camera.
■ Ni-MH Batteries
The capacity of Ni-MH batteries may be
temporarily reduced when new, after long
periods of disuse, or if they are repeatedly
recharged before being fully discharged. This
is normal and does not indicate a malfunction. Capacity can be increased by repeatedly
discharging the batteries using the discharge
option in the camera setup menu and recharging them using a battery charger.
Q CAUTION: Do not use the discharge option
with alkaline batteries.
The camera draws a small amount of current
even when off. Ni-MH batteries that have
been left in the camera for an extended period may be drawn down to the point that
they no longer hold a charge. Battery performance may also drop if the batteries are run
down in a device such as a flashlight. Use the
discharge option in the camera setup menu
If the batteries leak, clean the battery to discharge Ni-MH batteries. Batteries that
compartment thoroughly before in- no longer hold a charge even after repeatserting new batteries.
edly being discharged and recharged have
reached the end of their service life and must
If fluid from the battery comes into
be replaced.
contact with skin or clothing, flush
the affected area with water. If fluid Ni-MH batteries can be recharged in a batenters your eyes, immediately flush the tery charger (sold separately). Batteries may
affected area with water and seek become warm to the touch after charging.
medical attention. Do not rub your eyes. Refer to the instructions provided with the
Failure to observe this precaution could charger for more information. Use the charresult in permanent visual impairment. ger with compatible batteries only.
AC Power Adapters (Available Separately)
This section applies to all camera models.
Use only FUJIFILM AC power adapters designated for use with this camera. Other adapters could damage the camera.
• The AC power adapter is for indoor use only.
• Be sure the DC plug is securely connected
to the camera.
• Turn the camera off before disconnecting
the adapter. Disconnect the adapter by the
plug, not the cable.
• Do not use with other devices.
• Do not disassemble.
• Do not expose to high heat and humidity.
• Do not subject to strong physical shocks.
• The adapter may hum or become hot to the
touch during use. This is normal.
• If the adapter causes radio interference,
reorient or relocate the receiving antenna.
Ni-MH batteries gradually lose their charge
when not in use.
■ Disposal
Dispose of used batteries in accord with local
regulations.
vii
For Your Safety
Using the Camera
Do not aim the camera at extremely bright
light sources, such as the sun in a cloudless
sky. Failure to observe this precaution could
damage the camera image sensor.
Take Test Shots
Before taking photographs on important
occasions (such as at weddings or before
taking the camera on a trip), take a test shot
and view the result in the LCD monitor to ensure that the camera is functioning normally.
FUJIFILM Corporation can not accept liability
for damages or lost profits incurred as a result
of product malfunction.
Notes on Copyright
Unless intended solely for personal use, images recorded using your digital camera system
cannot be used in ways that infringe copyright laws without the consent of the owner.
Note that some restrictions apply to the
photographing of stage performances, entertainments, and exhibits, even when intended
purely for personal use. Users are also asked
to note that the transfer of memory cards
containing images or data protected under
copyright laws is only permissible within the
restrictions imposed by those copyright laws.
Handling
To ensure that images are recorded correctly,
do not subject the camera to impact or physical shocks while images are being recorded.
viii
Liquid Crystal
In the event that the LCD monitor is damaged,
care should be taken to avoid contact with liquid crystal. Take the urgent action indicated
should any of the following situations arise:
• If liquid crystal comes in contact with your
skin, clean the area with a cloth and then
wash thoroughly with soap and running
water.
• If liquid crystal enters your eyes, flush the affected eye with clean water for at least 15
minutes and then seek medical assistance.
• If liquid crystal is swallowed, rinse your
mouth thoroughly with water. Drink large
quantities of water and induce vomiting,
then seek medical assistance.
Electrical Interference
This camera may interfere with hospital or
aviation equipment. Consult with hospital
or airline staff before using the camera in a
hospital or on an aircraft.
Color Television Systems
NTSC (National Television System Committee)
is a color television telecasting specification
adopted mainly in the U.S.A., Canada, and
Japan. PAL (Phases Alternation by Line) is
a color television system adopted mainly in
European countries and China.
Exif Print (Exif Version 2.3)
Exif Print is a newly revised digital camera file
format in which information stored with phoAlthough the display is manufactured using tographs is used for optimal color reproducextremely high-precision technology, it may tion during printing.
contain pixels that are always lit or that do not
IMPORTANT NOTICE:
light. This is not a malfunction, and images reRead Before Using the Software
corded with the product are unaffected.
Direct or indirect export, in whole or in part,
Trademark Information
of licensed software without the permission
xD-Picture Card and E are trademarks of the applicable governing bodies is proof FUJIFILM Corporation. The typefaces in- hibited.
cluded herein are solely developed by DynaComware Taiwan Inc. Macintosh, QuickTime,
and Mac OS are trademarks of Apple Inc. in
the U.S.A. and other countries. Windows 7,
Windows Vista, and the Windows logo are
trademarks of the Microsoft group of companies. Adobe and Adobe Reader are either
trademarks or registered trademarks of Adobe Systems Incorporated in the U.S.A. and/or
other countries. The SDHC and SDXC logos
are trademarks of SD-3C, LLC. The HDMI logo
is a trademark. YouTube is a trademark of
Google Inc. All other trade names mentioned
in this manual are the trademarks or registered trademarks of their respective owners.
For Your Safety
NOTICES
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
Please read the “Safety Notes” and make
sure you understand them before using
the camera.
Perchlorate Material—special handling
may apply. See http://www.dtsc.ca.gov/
hazardouswaste/perchlorate.
For Customers in the U. S. A.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
FCC Statement: This device complies with Part
15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device
may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
CAUTION: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/
TV technician for help.
• You are cautioned that any changes or
modifications not expressly approved in
this manual could void the user’s authority
to operate the equipment.
This symbol on the batteries
or accumulators indicates that
those batteries shall not be treated as household waste.
If your equipment contains easy removable
batteries or accumulators please dispose
these separately according to your local requirements.
The recycling of materials will help to conserve natural resources. For more detailed
information about recycling this product,
please contact your local city office, your
Notes on the Grant: To comply with Part 15 of
household waste disposal service or the shop
the FCC Rules, this product must be used with
where you purchased the product.
a Fujifilm-specified ferrite-core A/V cable, USB
In Countries Outside the European Union, Norway,
cable, and DC supply cord.
Iceland and Liechtenstein: If you wish to discard
For Customers in Canada
this product, including the batteries or accuCAUTION: This Class B digital apparatus com- mulators, please contact your local authoriplies with Canadian ICES-003.
ties and ask for the correct way of disposal.
Disposal of Electrical and Electronic Equipment in
Private Households
In the European Union, Norway, Iceland and Liechtenstein: This symbol
on the product, or in the manual
and in the warranty, and/or on its
packaging indicates that this product shall not be treated as household waste. Instead it should be
taken to an applicable collection
point for the recycling of electrical
and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences to the environment and
human health, which could otherwise be
caused by inappropriate waste handling of
this product.
ix
About This Manual
Before using the camera, read this manual and the warnings in “For Your Safety” (P ii). For information on specific topics, consult the sources below.
Table of Contents .............................P
.............................P xi
The “Table of Contents” gives an overview of the entire manual. The principal camera operations are listed here.
Troubleshooting .......................... P 136
Having a specific problem with the
camera? Find the answer here.
Warning Messages and Displays ... P 142
Find out what’s behind that flashing
icon or error message in the display.
Memory Cards
Pictures can be stored in the camera’s internal memory or on optional SD, SDHC, and
SDXC memory cards (P 18), referred to in this manual as “memory cards.”
Temperature Warning
The camera will turn off automatically before its temperature or the temperature
of the battery rise above safe limits. Pictures taken when a temperature warning is
displayed may exhibit higher levels of “noise” (mottling). Turn the camera off and wait
for it to cool before turning it on again.
x
Table of Contents
For Your Safety ..................................................................ii
IMPORTANT SAFETY INSTRUCTIONS ..................................ii
Safety Notes ....................................................................iv
About This Manual ............................................................x
Before You Begin
Symbols and Conventions.................................................1
Supplied Accessories .........................................................1
Parts of the Camera ..........................................................2
Camera Displays ...............................................................6
Shooting ........................................................................6
Playback.........................................................................7
Display mode ...................................................................9
First Steps
Charging the Battery ......................................................13
Inserting the Battery and a Memory Card.....................15
Compatible Memory Cards .............................................18
Turning the Camera on and Off ......................................20
Camera Mode .................................................................20
Switching from portable mode to standby mode ...........21
Switching from standby mode to portable mode ...........21
Switching from standby mode to shooting mode
(Turning the camera on) ................................................22
Switching from shooting mode to standby mode
(Turning the camera off ) ................................................22
Playback Mode ...............................................................23
Basic Setup ......................................................................24
Basic Photography and Playback
Taking Pictures ................................................................25
Viewing Pictures .............................................................29
More on Photography
Shooting Mode ................................................................30
E (E AUTO/E Priority) .................31
R (E AUTO).................................................31
E Priority ..........................................................32
Adv. ADVANCED ..........................................................33
ADVANCED FILTER .........................................................33
r MOTION PANORAMA 360 .......................................34
i PRO FOCUS ...........................................................36
j PRO LOW-LIGHT ....................................................37
j MULTIPLE EXPOSURE...............................................38
i INDIVID. SHUTTER 3D ..............................................39
SP SCENE POSITION.......................................................41
M MANUAL ...................................................................42
A APERTURE PRIORITY AE ..............................................44
S SHUTTER PRIORITY AE ................................................44
P PROGRAM AE ..............................................................45
C1/C2 CUSTOM MODE .................................................46
Focus Lock ........................................................................47
d Exposure Compensation ..........................................49
F Macro Mode (Close-ups) ...........................................50
N Using the Flash (Super-Intelligent Flash) .................51
xi
Table of Contents
h Using the Self-Timer .................................................53
The Fn Button ..................................................................54
The E-Fn Button...............................................................55
Using the E-Fn BUTTON CUSTOM SETTING Menu .............55
R Continuous Shooting ...............................................57
I TOP n .....................................................................58
P BEST FRAME CAPTURE...........................................58
O AE BKT ..................................................................60
W ISO BKT .................................................................60
X FILM SIMULATION BKT ............................................60
Y DYNAMIC RANGE BKT .............................................61
F Focus Mode ...............................................................62
Focus Frame Selection ....................................................65
b Intelligent Face Detection .......................................66
n Face Recognition ......................................................67
Adding New Faces ..........................................................67
Viewing, Editing, and Deleting Existing Data .................69
Adding Faces Automatically ...........................................69
More on Playback
Playback Options.............................................................71
Continuous Shooting......................................................71
I Favorites: Rating Pictures .........................................71
Playback Zoom ...............................................................72
Multi-Frame Playback ....................................................73
A Deleting Pictures......................................................74
b Image Search............................................................75
m PhotoBook Assist .....................................................76
Creating a PhotoBook.....................................................76
xii
Viewing Photobooks ......................................................77
Editing and Deleting Photobooks ...................................77
Viewing Panoramas ........................................................78
Viewing Photo Information............................................79
Movies
Recording Movies ............................................................81
Movie Frame Size ...........................................................83
Viewing Movies ...............................................................84
Connections
Viewing Pictures on TV ...................................................85
Printing Pictures via USB ................................................87
Printing the DPOF Print Order.........................................89
Viewing Pictures on a Computer ....................................91
Windows: Installing MyFinePix Studio ...........................91
Macintosh: Installing FinePixViewer...............................94
Connecting the Camera ..................................................96
Menus
Using the Menus: Shooting Mode ..................................99
Using the Shooting Menu...............................................99
Shooting Menu Options ...............................................100
A SCENE POSITION...................................................100
A E MODE ..................................................100
A Adv. MODE ..........................................................100
N ISO......................................................................100
O IMAGE SIZE ..........................................................101
T IMAGE QUALITY ...................................................101
U DYNAMIC RANGE .................................................102
P FILM SIMULATION ................................................103
D WHITE BALANCE ..................................................104
d WB SHIFT ............................................................106
Table of Contents
f COLOR .................................................................106
q SHARPNESS .........................................................106
r HIGHLIGHT TONE ..................................................106
s SHADOW TONE.....................................................106
h NOISE REDUCTION ................................................106
R INTELLIGENT DIGITAL ZOOM ..................................106
R CONTINUOUS .......................................................106
Z ADVANCED ANTI BLUR ..........................................107
b FACE DETECTION SET-UP .......................................107
C PHOTOMETRY ......................................................107
F FOCUS MODE .......................................................107
F FOCUS AREA ........................................................108
F Fn BUTTON ..........................................................108
E E-Fn BUTTON CUSTOM SETTING .............................108
v DISP. CUSTOM SETTING .........................................109
I FLASH .................................................................109
W MOVIE SET-UP .....................................................110
K CUSTOM SET ........................................................110
Using the Menus: Playback Mode ................................111
Using the Playback Menu .............................................111
Playback Menu Options................................................112
m PHOTOBOOK ASSIST..............................................112
b IMAGE SEARCH ....................................................112
A ERASE .................................................................112
j MARK FOR UPLOAD TO ..........................................113
I SLIDE SHOW ........................................................114
j RAW CONVERSION................................................115
B RED EYE REMOVAL ...............................................117
D PROTECT..............................................................117
G CROP...................................................................118
O RESIZE .................................................................118
C IMAGE ROTATE .....................................................119
E COPY...................................................................119
F VOICE MEMO .......................................................120
i ERASE FACE RECOG. ..............................................120
K PRINT ORDER (DPOF) ............................................121
J DISP ASPECT ........................................................121
The Setup Menu ............................................................122
Using the Setup Menu..................................................122
Setup Menu Options ....................................................123
F DATE/TIME ..........................................................123
N TIME DIFFERENCE .................................................123
Q a ....................................................123
R RESET..................................................................124
o SILENT MODE.......................................................124
b SOUND SET-UP ....................................................124
A SCREEN SET-UP ....................................................125
Z POWER MANAGEMENT .........................................126
L IS MODE ..............................................................127
B RED EYE REMOVAL ...............................................127
C AF ILLUMINATOR ..................................................128
j RAW ...................................................................128
t SAVE DATA SET-UP ...............................................129
I FOCUS CONTROL DIAL...........................................130
Q VIDEO SYSTEM .....................................................130
S CUSTOM RESET ....................................................131
K FORMAT ..............................................................131
xiii
Table of Contents
Technical Notes
Optional Accessories .....................................................132
Accessories from FUJIFILM............................................133
Caring for the Camera ...................................................134
Storage and Use ...........................................................134
Cleaning .......................................................................135
Traveling ......................................................................135
Troubleshooting
Problems and Solutions ................................................136
Warning Messages and Displays ..................................142
Appendix
Memory Card Capacity ..................................................146
Specifications ................................................................147
xiv
Before You Begin
Symbols and Conventions
The following symbols are used in this manual:
Q : This information should be read before use to ensure correct operation.
R : Additional information that may be helpful when using the camera.
P: Other pages in this manual on which related information may be found.
Menus and other text in the displays are shown in bold. In the illustrations in
this manual, displays may be simplified for explanatory purposes.
Supplied Accessories
The following items are included with the camera:
NP-50A Rechargeable
battery
BC-50B battery charger
• Strap
Plug adapter *
USB cable
Attaching the Strap
Attach the strap
as shown.
CD-ROM (contains this
manual)
* Shape of adapter varies with region of sale.
1
Parts of the Camera
For more information, refer to the page listed to the right of each item.
Selector button
Move cursor up
d (exposure compensation) button (P 49)
b (delete) button (P 29)
Move cursor left
F (macro) button (P 50)
Sub-command dial
MENU/OK button
Move cursor right
N (flash) button (P 51)
Move cursor down
h (self-timer) button (P 53)
* The illustrations in this manual have been simplified for explanatory purposes.
2
Before You Begin
Parts of the Camera
1
2
3
4
5
Mode dial ................................................................... 30
Shutter button ........................................................... 27
Fn (function) button .................................................. 54
Flash .......................................................................... 51
Zoom ring .................................................................. 26
ON/OFF switch .......................................................... 22
6 Microphone.........................................................81, 120
7 Lens cover .................................................................. 22
8 AF-assist illuminator ................................................ 128
Self-timer lamp.......................................................... 53
9 Strap eyelet .................................................................. 1
10 Terminal cover.................................................85, 87, 96
11 DC coupler cable cover ............................................. 133
12 Battery-chamber cover latch ...................................... 15
13 Battery-chamber cover .............................................. 15
14 Speaker ...............................................................84, 120
1 Press and hold the E-Fn button for monitor sunlight mode.
2 Press and hold the DISP/BACK button until o is displayed.
Before You Begin
15
16
17
18
19
20
21
22
23
24
25
Tripod mount
USB multi-connector.......................................85, 87, 96
Connector for HDMI cable........................................... 86
Memory card slot ....................................................... 16
Battery latch ........................................................ 15, 17
Battery chamber ........................................................ 15
Indicator lamp.............................................................. 5
Main-command dial .................................................... 4
a (playback) button.......................................... 29, 71
t (movie recording) button ..................................... 81
E-Fn (extended function) button ............................... 55
Monitor sunlight mode 1............................................... 8
26 DISP (display)/BACK button.............................9, 24, 79
o (silent mode) button 2 ............................................ 5
27 LCD monitor ................................................................. 6
28 N (flash pop-up) Switch ............................................ 51
3
Parts of the Camera
Main-command dial/Sub-command dial
Rotate the main/sub-command dial to set the aperture value or shutter speed. You
can also select items using the main/sub-command dial for the selector button. To
adjust focus for MANUAL, rotate the sub-command dial (P 62).
Main-command
dial
Sub-command
dial
Press the center of the main-command dial for some operations such as
switching the setting item in M mode.
Control Lock
To lock the selector button (d / N / h / F) and the E-Fn button, press MENU/OK until
X is displayed. This prevents accidental operation during shooting. The controls
can be unlocked by pressing MENU/OK until X is no longer displayed.
4
Before You Begin
Parts of the Camera
The Indicator Lamp
The indicator lamp shows camera status as follows:
Indicator lamp
Glows green
Blinks green
Blinks green and orange
Glows orange
Blinks orange (fast)
Blinks orange (slow)
Blinks red
Camera status
Focus locked.
Blur, focus, or exposure warning. Picture can be taken.
Recording pictures. Additional pictures can be taken.
Recording pictures. No additional pictures can be taken at this time.
Flash charging; flash will not fire when picture is taken.
The zoom ring is positioned between 25 and STANDBY. Picture cannot be taken.
Lens or memory error.
Silent Mode
In situations in which camera sounds or lights may be unwelcome, hold the DISP/
BACK button down until o is displayed.
The camera speaker, flash, and AF-assist illuminator/self-timer lamp turn off and flash
and volume settings can not be adjusted (note that the flash will still fire when C
is selected in scene mode). To restore normal operation, press the DISP/BACK button
until the o icon is no longer displayed.
Before You Begin
5
Parts of the Camera
Camera Displays
The following types of indicator may be displayed during shooting and playback. Indicators vary with camera settings.
■ Shooting
100
1000
1
2
3
4
5
6
7
8
9
10
11
F
F3.3
Flash mode ................................................................ 51
Macro (close-up) mode .............................................. 50
Self-timer indicator .................................................... 53
Continuous shooting mode ........................................ 57
Advanced anti blur ..................................................... 32
White balance .......................................................... 104
Film simulation ........................................................ 103
Dynamic range ......................................................... 102
Internal memory indicator *
Number of available frames ..................................... 146
Image size/quality ................................................... 101
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Movie mode ............................................................... 83
Temperature warning............................................x, 142
Blur warning .......................................................52, 142
Electronic level ......................................................... 109
IS mode .................................................................... 127
Date stamp............................................................... 130
Silent mode indicator ........................................... 5, 124
Battery level................................................................. 8
Sensitivity ................................................................ 100
Monitor sunlight mode ................................................ 8
Focus warning .....................................................27, 142
Aperture............................................................... 42, 44
Shutter speed....................................................... 42, 44
Metering .................................................................. 107
Shooting mode .......................................................... 30
Manual focus indicator ............................................... 62
Exposure indicator...................................................... 49
Histogram .................................................................. 12
Focus frame................................................................ 65
Intelligent digital zoom............................................ 106
* a: indicates that no memory card is inserted and that pictures will be stored in the camera’s internal memory (P 16).
6
Before You Begin
Parts of the Camera
■ Playback
100-0001
4:3 F
YouTube
12/31/2050 10:00 AM
1/1000
Before You Begin
F2.8
+1 1
3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Favorites..................................................................... 71
Intelligent Face Detection indicator.....................66, 107
Red-eye removal indicator ....................................... 117
Pro focus mode, pro low-light mode .................... 36, 37
Motion panorama z ........................................ 34, 78
3D image.................................................................... 39
Portrait enhancer ....................................................... 41
Advanced Filter .......................................................... 33
Frame number ......................................................... 129
Gift image .................................................................. 71
Dynamic range ......................................................... 102
E mode .......................................................... 31
Playback mode indicator ...................................... 29, 71
Mark for upload to ................................................... 113
Photobook assist ........................................................ 76
Voice memo indicator .............................................. 120
DPOF print indicator ................................................... 89
Protected image....................................................... 117
7
Parts of the Camera
Battery Level
Battery level is shown as follows:
Indicator
D (white)
C (white)
B (red)
A (blinks red)
Description
Battery partially discharged.
Battery more than half discharged.
Low battery. Charge as soon as possible.
Battery exhausted. Charge battery.
Bright Ambient Lighting
Reflections and glare caused by bright ambient lighting may make it hard to see
the display in the monitor, particularly when the camera is used outdoors. This can
be addressed by holding the E-Fn button to trigger outdoor mode. Outdoor mode
can also be enabled using the A SCREEN SET-UP > MONITOR SUNLIGHT MODE
option (P 125).
8
Before You Begin
Parts of the Camera
Display mode
Press DISP/BACK to cycle through display modes as follows:
• Shooting
100
2000
d
F5.6
2000
200
INFORMATION1 ON
100
2000
F5.6
CUSTOM
F5.6
F
200
INFORMATION2 ON
F
200
INFORMATION OFF
INFORMATION1 ON
INFORMATION1 ON can be displayed in a shooting mode
which is P, A, S, M, C1 or C2. The icons are displayed on the
left side of shutter speed and aperture to change them quickly
(P 109).
Before You Begin
c
2000
F5.6
d
9
Parts of the Camera
Custom Display
Choose items for display using v DISP. CUSTOM SETTING in the shooting menu
(P 109).
Focal Length, Aperture, Shutter Speed
Following information is displayed by rotating the zoom ring in
INFORMATION1 ON or INFORMATION2 ON.
Following information is displayed when
aperture or shutter speed is set in INFORMATION1 ON.
10
M
c
2.2
2000
2.5
d
2.8
8
F5.6
Aperture
3.2
5
50
0
35
5
25
2
5
Focal length
500
64
40
c2000
M
800
800
d
100
00 12
200
0
F5.6
Shutter speed
Before You Begin
Parts of the Camera
• Playback
100-0001
3:2 F
12/31/2050
1 / 1000
10 : 00 AM
F4.5
-1 2 3 200
INFORMATION ON
INFORMATION OFF
100-0001
100-0001
3:2 F
ISO 200
1/1000 F4.5
:
: OFF
:
: -1 2 3
12/31/2050
10 : 00 AM
DETAIL INFORMATION
Before You Begin
3
12/31/2050
10 : 00 AM
I FAVORITES
11
Parts of the Camera
Histograms
Histograms show the distribution of tones in the image. Brightness is shown by the
horizontal axis, the number of pixels by the vertical axis.
No. of
pixels
Pixel brightness
Shadows
Highlights
Optimal exposure: Pixels are distributed in an even curve
throughout the tone range.
Overexposed: Pixels are clustered at the right side of the graph.
Underexposed: Pixels are clustered at the left side of the graph.
12
Before You Begin
First Steps
Charging the Battery
The battery is not charged at shipment. Charge the battery before use.
1 Attach the plug adapter.
Attach the plug adapter as shown, making
sure that it is fully inserted and clicks into
place on the charger terminals.
Q The plug adapter is exclusively for use with the
supplied battery charger. Do not use it with
other devices.
Battery charger
Plug adapter
2 Place the battery in the supplied battery charger.
Insert the battery in the orientation indicated by the DFC
labels.
Battery
Arrow
Charge lamp
The camera uses an NP-50A rechargeable battery.
DFC label
DFC label
13
Charging the Battery
3 Plug the charger in.
Plug the charger into an indoor power outlet. The charging indicator will
light.
The Charging Indicator
The charging indicator shows battery charge status as follows:
Charging indicator
Off
On
Blinks
Battery status
Battery not inserted.
Battery fully charged.
Battery charging.
Battery fault.
Action
Insert the battery.
Remove the battery.
—
Unplug the charger and remove the battery.
4 Charge the battery.
Remove the battery when charging is complete. See the specifications
(P 151) for charging times (note that charging times increase both at high
temperatures and at low temperatures).
Q Unplug the charger when it is not in use.
14
First Steps
Inserting the Battery and a Memory Card
Although the camera can store pictures in internal memory, optional SD,
SDHC, and SDXC memory cards (sold separately) can be used to store additional pictures. After charging the battery, insert the battery and memory
card as described below.
1 Open the battery-chamber cover.
R Be sure the camera is off before opening
the battery-chamber cover.
Q Do not open the battery-chamber cover
when the camera is on. Failure to observe this precaution could result in damage to image files or memory cards.
Q Do not use excessive force when handling the battery-chamber cover.
2 Insert the battery.
Align the orange stripe on the battery with the orange
battery latch and slide the battery into the camera, keeping the battery latch pressed to one side. Confirm that the
battery is securely latched.
Orange stripe
Q Insert the battery in the correct orientation. Do NOT use force
or attempt to insert the battery upside down or backwards.
The battery will slide in easily in the correct orientation.
Battery latch
First Steps
15
Inserting the Battery and a Memory Card
3 Insert the memory card.
Holding the memory card in the orientation shown at
right, slide it in until it clicks into place at the back of
the slot.
Q Be sure card is in the correct orientation; do not insert at
an angle or use force. If the memory card is not correctly
inserted or no memory card is inserted, a will appear in
the LCD monitor and internal memory will be used for recording and playback.
Q SD/SDHC/SDXC memory cards can be locked, making it
impossible to format the card or to record or delete images. Before inserting an SD/SDHC/SDXC memory card,
slide the write-protect switch to the unlocked position.
Click
Write-protect switch
4 Close the battery-chamber cover.
16
First Steps
Inserting the Battery and a Memory Card
R Using an AC Power Adapter
The camera can be powered by an optional AC power adapter and DC coupler (sold
separately). See the manuals provided with the AC power adapter and DC coupler for
details.
Removing the Battery and Memory Card
Before removing the battery or memory card, turn the camera off and open the
battery-chamber cover.
To remove the battery, press the battery latch to the side, and
slide the battery out of the camera as shown.
Battery latch
To remove the memory card, press it in and release it slowly.
The card can then be removed by hand. When a memory card
is removed, the card could come out of the slot too quickly. Use
your finger to hold it and gently release the card.
First Steps
17
Inserting the Battery and a Memory Card
■ Compatible Memory Cards
FUJIFILM and SanDisk SD, SDHC, and SDXC memory cards have been approved for use in the camera. A complete list of approved memory cards
is available at http://www.fujifilm.com/support/digital_cameras/compatibility/.
Operation is not guaranteed with other cards. The camera can not be used
with xD-Picture Cards or MultiMediaCard (MMC) devices.
Q Memory Cards
• Do not turn the camera off or remove the memory card while the memory card is
being formatted or data are being recorded to or deleted from the card. Failure to
observe this precaution could damage the card.
• Format SD/SDHC/SDXC memory cards before first use, and be sure to reformat all
memory cards after using them in a computer or other device. For more information
on formatting memory cards, see “K FORMAT” (P 131).
• Memory cards are small and can be swallowed; keep out of reach of children. If a
child swallows a memory card, seek medical assistance immediately.
• miniSD or microSD adapters that are larger or smaller than the standard dimensions
of an SD/SDHC/SDXC card may not eject normally; if the card does not eject, take
the camera to an authorized service representative. Do not forcibly remove the card.
• Do not affix labels to memory cards. Peeling labels can cause camera malfunction.
• Movie recording may be interrupted with some types of SD/SDHC/SDXC memory
card. Use a G card or better when shooting HD or high-speed movies.
18
First Steps
Inserting the Battery and a Memory Card
• The data in internal memory may be erased or corrupted when the camera is repaired. Please note that the repairer will be able to view pictures in internal memory.
• Formatting a memory card or internal memory in the camera creates a folder in
which pictures are stored. Do not rename or delete this folder or use a computer or
other device to edit, delete, or rename image files. Always use the camera to delete
pictures from memory cards and internal memory; before editing or renaming files,
copy them to a computer and edit or rename the copies, not the originals.
Q Batteries
• Remove dirt from the battery terminals with a clean, dry cloth. Failure to observe this
precaution could prevent the battery from charging.
• Do not affix stickers or other objects to the battery. Failure to observe this precaution
could make it impossible to remove the battery from the camera.
• Do not short the battery terminals. The battery could overheat.
• Read the cautions in “The Battery and Power Supply” (P vi).
• Use only battery chargers designated for use with the battery. Failure to observe this
precaution could result in product malfunction.
• Do not remove the labels from the battery or attempt to split or peel the outer casing.
• The battery gradually loses its charge when not in use. Charge the battery one or
two days before use.
First Steps
19
Turning the Camera on and Off
Camera Mode
The camera has three characteristic modes (status). Choose a camera mode
according to the purpose.
Mode
Power
Portable mode
The lens is housed and
locked to carry the camera by a camera case or
a bag (P 21).
Off
Standby mode
The camera becomes
turned off temporarily
in this mode (P 21).
Off
Shooting mode
The camera turns on
and can take pictures
(P 22).
On
20
Indicator
First Steps
Turning the Camera on and Off
Switching from portable mode to standby mode
Portable mode
The factory default is
portable mode.
Rotate the zoom ring until
it stops as shown.
Standby mode
Rotate the zoom ring to
STANDBY.
Pull the zoom ring until it
clicks.
Switching from standby mode to portable mode
Standby mode
When the camera is in
shooting mode, rotate the
zoom ring to STANDBY.
Rotate the zoom ring until it
stops as shown.
Portable mode
Rotate the zoom ring until
fitting the red marks.
Press the zoom ring until
it stops.
First Steps
21
Turning the Camera on and Off
Q If the lens is not locked correctly, it may protrude.
Switching from standby mode to shooting mode (Turning the camera on)
Standby mode
Rotate the zoom ring to 25.
The camera turns on and the
lens cover opens.
Shooting mode
R Switching to Playback Mode
Press the a button to start playback. Press the shutter button halfway to return to
shooting mode.
Switching from shooting mode to standby mode (Turning the camera off )
Shooting mode
Rotate the zoom ring to
STANDBY.
Standby mode
Q Fingerprints and other marks on the lens can affect pictures. Keep the lens clean.
Q Do not touch the lens cover during pressing or pulling the zoom ring. Failure to
observe this precaution could result in damage to the camera.
Q Make sure that the camera turns off before housing the lens and the zoom ring.
22
First Steps
Turning the Camera on and Off
Playback Mode
To turn the camera on and begin playback, press the a button for about a
second.
Press the a button again to turn the camera off.
R Auto Power Off
The camera will turn off automatically if no operations are performed for the length of
time selected for Z POWER MANAGEMENT > AUTO POWER OFF (P 126).
First Steps
23
Basic Setup
A language-selection dialog is displayed the first time the camera is turned
on. Set up the camera as described below (you can reset the clock or change
languages at any time using the F DATE/TIME or Q a options in
the setup menu; for information on displaying the setup menu, see page 122).
1 Highlight a language and press MENU/OK.
R Press DISP/BACK to skip the current step. Any steps you skip
will be displayed the next time the camera is turned on.
START MENU
ENGLISH
FRANCAIS
DEUTSCH
ESPAÑOL
PORTUGUÊS
SET
2 The date and time will be displayed. Press the selector
left or right to highlight the year, month, day, hour, or
minute and press up or down to change. To change the
order in which the year, month, and day are displayed,
highlight the date format and press the selector up or
down. Press MENU/OK when settings are complete.
NO
DATE/TIME NOT SET
2014
2013
YY. MM. DD
2012
2011
2010
SET
1. 1 12 : 00
AM
NO
3 Power management options will be displayed. Press the selector up or
down to highlight one of the following options and then press MENU/OK:
• n POWER SAVE: Save battery power.
• o CLEAR DISPLAY: Choose for a brighter, higher quality display.
R The Camera Clock
If the battery is removed for an extended period, the camera clock will be reset and the
language-selection dialog will be displayed when the camera is turned on.
24
First Steps
Basic Photography and Playback
Taking Pictures
This section describes how to take pictures in R (E AUTO) mode.
1 Select E mode.
Turn the camera on and rotate the mode dial to EXR. The R display will
appear in the LCD monitor.
Scene Icon ((P
P 31)
The camera automatically selects the appropriate scene.
The o Icon
In R mode, the camera continuously adjusts focus and searches for faces, increasing the drain on the battery. o is displayed in the LCD monitor.
R The camera analyses the scene and selects the preferred E mode when
the shutter button is pressed halfway (P 32).
R To raise the flash when lighting is poor, slide the flash pop-up switch (P 51).
25
Taking Pictures
2 Frame the picture.
Use the zoom ring to frame the picture in the display. The zoom indicator
appears.
Zoom indicator
Zoom ring
5
50
0
35
5
25
2
5
Holding the Camera
Hold the camera steady with both hands and brace your
elbows against your sides. Shaking or unsteady hands can
blur your shots.
To prevent pictures that are out of focus or too dark (underexposed), keep your fingers and other objects away from
the lens and flash.
26
Basic Photography and Playback
Taking Pictures
3 Focus.
Press the shutter button halfway to focus.
R The lens may make a noise when the camera focuses;
this is normal. If the subject is poorly lit, the AF-assist
illuminator may light; see “C AF ILLUMINATOR”(P 128)
for information on disabling the illuminator.
Double
beep
If the camera is able to focus, it will beep twice and the indicator lamp will
glow green.
If the camera is unable to focus, the focus frame will turn red, s will be displayed, and the indicator lamp will blink green. Change the composition
or use focus lock (P 47).
Basic Photography and Playback
27
Taking Pictures
4 Shoot.
Smoothly press the shutter button the rest of the way
down to take the picture.
Click
The Shutter Button
The shutter button has two positions. Pressing the shutter button halfway sets
focus and exposure; to shoot, press the shutter button the rest of the way down.
28
Basic Photography and Playback
Viewing Pictures
Pictures can be viewed in the LCD monitor. When taking important photographs, take a test shot and check the results.
1 Press the a button.
The most recent picture will be displayed.
2 View additional pictures.
Press the selector right to view pictures in the order
recorded, left to view pictures in reverse order.
Press the shutter button to exit to shooting mode.
Deleting Pictures
To delete the picture currently displayed in the monitor, press the
selector up (b), and choose from the options.
To exit without deleting the picture, highlight CANCEL and press MENU/OK.
R Pictures can also be deleted from the playback menu (P 74).
Basic Photography and Playback
29
More on Photography
Shooting Mode
Choose a shooting mode according to the scene or
type of subject. To select a shooting mode, align the
mode icon with the mark next to the mode dial.
M, A, S, P: Select for full control over camera settings
(P 42), including aperture (M and A) and/or shutter
speed (M and S).
E: Improve clarity, reduce
noise, increase dynamic range,
or let the camera automatically
adjust settings to suit the scene
(P 31).
B (AUTO): A simple “point-andshoot” mode recommended for
first-time users of digital cameras.
C1/C2 (CUSTOM): Recall stored
settings for modes P, S, A, M and
all EXR modes except R (P 46).
SP (SCENE POSITION): Choose a
scene suited to the subject or
shooting conditions and let the
camera do the rest (P 41).
Adv. (ADVANCED): Sophisticated techniques made easy
(P 33).
30
Shooting Mode
E ((E
E AUTO/
AUTO/E
E Priority)
Optimize settings for your current subject or improve clarity, reduce
noise, or enhance dynamic range. Rotate the mode dial to EXR and
choose one of the following E modes in the shooting menu.
■ R (E AUTO)
The camera automatically selects the scene and E
mode according to shooting conditions (P 25).
R If S is selected for O IMAGE SIZE in R mode, the camera
will automatically select the optimal image size.
Scene icon
The Scene Icon
The camera selects from the following scenes:
Scene
Main subject
Non-portrait
Normal
Backlit
Moving object
Portrait and Normal
motion
Backlit
Portrait
AUTO
a
d
g
c
a
b
LANDSCAPE
c
dc
gc
cc
ac
bc
NIGHT
NIGHT (TRIPOD) MACRO
d*
h*
e
—
dd * dh *
—
—
—
cd ch ce
—
ad ah
—
—
—
BEACH
u
du
gu
cu
au
bu
SUNSET
v
dv
gv
cv
av
bv
SNOW
w
dw
gw
cw
aw
bw
SKY &
SKY GREENERY GREENERY
x
y
z
dx dy
dz
gx gy
gz
cx cy
cz
ax ay
az
bx by
bz
* If n is displayed, the camera will take a series of shots (advanced anti-blur; P 32).
Q The mode selected may vary with shooting conditions. If the mode and subject do not match,
select B mode (P 30) or choose SP (P 41) and select a scene manually.
More on Photography
31
Shooting Mode
Advanced Anti Blur
When n is displayed, the camera will take a series of exposures and combine them
to form a single image, reducing “noise” (mottling) and blur.
R n is available when ON is selected for Z ADVANCED ANTI BLUR (P 107) and
the flash (P 51) is off or set to auto.
Q Some time may be required to combine the exposures into a single image. A
single combined image may not be created if the subject or camera moves during shooting. Keep the camera steady during shooting and do not move the
camera until shooting is complete.
Q Frame coverage is reduced.
The E Icon
When the shutter button is pressed halfway, the camera chooses the preferred E mode:
• S (RESOLUTION PRIORITY): Produces crisp, clear shots.
• T (HIGH ISO & LOW NOISE): Reduces noise in pictures taken at high sensitivities.
• U (D-RANGE PRIORITY): Increases the amount of detail visible in highlights.
■ E Priority
Select this mode to manually choose from the following E modes:
• S (RESOLUTION PRIORITY): Choose for crisp, clear shots.
• T (HIGH ISO & LOW NOISE): Reduce noise in pictures taken at high sensitivities.
• U (D-RANGE PRIORITY): Increase the amount of detail visible in highlights.
U DYNAMIC RANGE (P 102) can be set to Z (1600%) and Y (800%).
32
More on Photography
Shooting Mode
Adv. ADVANCED
This mode combines “point-and-shoot” simplicity with sophisticated photographic techniques. The A Adv. MODE option can be
used to choose from the following advanced modes:
■ ADVANCED FILTER
Take photos with filter effects. Choose from the following filters.
Filter
G TOY CAMERA
H MINIATURE
I POP COLOR
J HIGH-KEY
K DYNAMIC TONE
u PARTIAL COLOR (RED)
v PARTIAL COLOR (ORANGE)
w PARTIAL COLOR (YELLOW)
x PARTIAL COLOR (GREEN)
y PARTIAL COLOR (BLUE)
z PARTIAL COLOR (PURPLE)
Description
Choose for a retro toy camera effect.
The tops and bottoms of pictures are blurred for a diorama effect.
Create high-contrast images with saturated colors.
Create bright, low-contrast images.
Dynamic tone expression is used for a fantasy effect.
Areas of the image that are the selected color are recorded in that
color. All others areas of the image are recorded in black-and-white.
R Depending on the subject and camera settings, images may in some cases be
grainy or vary in brightness and hue.
More on Photography
33
Shooting Mode
■ r MOTION PANORAMA 360
Follow an on-screen guide to take photos that will automatically be joined to form a panorama. The camera
zooms all the way out and remains fixed at the widest
angle until shooting is complete.
1 Rotate the zoom ring until the zoom indicator turns white (P 26).
2 To select the angle through which you will pan the camera while shooting, press the selector down. Press the selector left or right to highlight an
angle and press MENU/OK.
3 Press the selector right to view a choice of pan directions. Press the selector left or right to highlight a pan direction and press MENU/OK.
4 Press the shutter button all the way down to start recording. There is no
need to keep the shutter button pressed during recording.
5 Pan the camera in the direction shown by the arrow.
120
Shooting ends automatically when the progress bar is
full and the panorama is complete.
R Shooting ends if the shutter button is pressed all the way
down during shooting. No panorama will be recorded if
the shutter button is pressed before the camera has been
panned through 120 °.
34
Progress bar
More on Photography
Shooting Mode
Q Panoramas are created from multiple frames. The camera may in some cases record
an greater or lesser angle than selected or be unable to stitch the frames together
perfectly. The last part of the panorama may not be recorded if shooting ends before the panorama is complete.
Q Shooting may be interrupted if the camera is panned too quickly or too slowly. Panning the camera in a direction other than that shown cancels shooting.
Q The desired results may not be achieved with moving subjects, subjects close to
the camera, unvarying subjects such as the sky or a field of grass, subjects that are
in constant motion, such as waves and waterfalls, or subjects that undergo marked
changes in brightness. Panoramas may be blurred if the subject is poorly lit.
z
Choose z for seamless 360° panoramas that can be played back in a loop (P 78).
R The t SAVE DATA SET-UP > SAVE ORG IMAGE option can be used to record a
v panorama in addition to a seamless z panorama (P 129).
Q Depending on the subject and shooting conditions, the camera may produce
distorted results or a v panorama. The top and bottom of the area visible in
the shooting display are cropped out and white strips may appear at the top and
bottom of the display.
For Best Results
For best results, move the camera in a small circle at a steady speed, keeping the
camera horizontal and being careful only to pan in the direction shown by the
guides. If the desired results are not achieved, try panning at a different speed.
More on Photography
35
Shooting Mode
■ i PRO FOCUS
The camera takes up to three shots each time the shutter
button is pressed, softening the background to emphasize the main subject. The amount of softening can be
adjusted before shooting by rotating the sub-command
dial. Use for portraits or photos of flowers similar to those
produced by SLR cameras.
R Softening can not be applied to background objects that are too close to the main
subject. If a message stating that the camera can not create the effect is displayed
when the camera focuses, try backing away from your subject and zooming in. The
camera may also be unable to soften the background if the subject is moving; if
prompted, check the results and try again.
36
More on Photography
Shooting Mode
■ j PRO LOW-LIGHT
Each time the shutter button is pressed, the camera makes
four exposures and combines them into a single photograph. Use to reduce noise and blur when photographing
poorly lit subjects or static subjects at high zoom ratios.
R A single combined photograph may not be created with some
scenes or if the subject or camera moves during shooting. Do not move the camera until shooting is complete.
PRO FOCUS/PRO LOW-LIGHT
To save unprocessed copies of pictures taken in these modes, select ON for t SAVE
DATA SET-UP > SAVE ORG IMAGE (P 129).
Q Keep the camera steady during shooting.
Q Frame coverage is reduced.
More on Photography
37
Shooting Mode
■ j MULTIPLE EXPOSURE
Create a photograph that combines two exposures.
1 Take the first shot.
2 Press MENU/OK. The first shot will be shown superimposed on the view
through the lens as a guide to taking the second shot.
R To return to Step 1 and retake the first shot, press the selector left. To save the
first shot and exit without creating a multiple exposure, press DISP/BACK.
3 Take the second shot.
4 Press MENU/OK to create the multiple exposure, or press the selector left to
return to Step 3 and retake the second shot.
38
More on Photography
Shooting Mode
■ i INDIVID. SHUTTER 3D
Take two shots from different angles to create a 3D image.
1 To choose the order in which the pictures are taken,
press the selector right to display the current order and
then press the selector left or right to choose from the
options below.
TURN
G: Take the left shot first.
H: Take the right shot first.
2 Press the shutter button to take the first shot.
R To exit without recording a picture, press DISP/BACK.
3 The first shot will be shown superimposed on the view through the lens.
Using it as a guide, frame the second shot and press the shutter release
button.
R The 3D effect may not be visible with some subjects or under some shooting conditions. For
best results, the distance the camera is moved
between shots should be about 1/30th to 1/50th of
the distance to the subject.
R The camera will turn off automatically if no operations performed for the time
selected for Z POWER MANAGEMENT > AUTO POWER OFF (P 126). The first
shot will not be saved if the second shot is not taken before the camera turns
off.
More on Photography
39
Shooting Mode
Viewing and Printing 3D Images
• The camera displays images in 2D. Press the selector down to toggle between the
first and second shots.
• Devices equipped for 3D display, such as the FINEPIX REAL 3D V3 digital photo frame
or FINEPIX REAL 3D W3 digital camera, will display the images in 3D. Note that the
FINEPIX REAL 3D W3 only displays images of size P or smaller.
• 3D prints can be ordered from http://www.fujifilm.com/3d/print/
• The supplied software displays 3D anaglyph images. 3D photos can also be viewed
using other applications that support the MP format.
• 3D TVs that support the MP format can display images in 3D. See the manual for
your TV for details.
Q Images are not output in 3D when printed directly from the camera.
Q 3D images are displayed in 2D in slide shows and when output on a conventional
TV.
Q 3D images can not be edited or retouched.
Note: The MP (Multi-Picture) format is a CIPA standard for files containing multiple still images. Files
in MP format are referred to as “MP files” and have the extension “*.MPO”. The camera uses this
format for 3D images.
40
More on Photography
Shooting Mode
SP SCENE POSITION
The camera offers a choice of “scenes,” each adapted to particular
shooting conditions or a specific type of subject. Use the A SCENE
POSITION option to choose the scene assigned to the SP position
on the mode dial.
Scene
C NATURAL & N
D NATURAL LIGHT
h PORTRAIT
Z PORTRAIT
ENHANCER
M LANDSCAPE
N SPORT
O NIGHT
H NIGHT (TRIPOD)
p FIREWORKS
Q SUNSET
R SNOW
Description
The camera takes two shots: one without the flash and one with.
Capture natural lighting under low-light conditions.
Choose for portraits.
Choose for a smooth skin effect when shooting portraits.
Choose for daylight shots of buildings and landscapes.
Choose when photographing moving subjects.
Choose this mode for poorly lit twilight or night scenes.
Choose this mode for slow shutter speeds when shooting at night.
Slow shutter speeds are used to capture the expanding burst of light from
a firework.
Choose this mode to record the vivid colors in sunrises and sunsets.
Choose for crisp, clear shots that capture the brightness of scenes dominated by shining white snow.
More on Photography
41
Shooting Mode
Scene
s BEACH
f UNDERWATER
U PARTY
V FLOWER
W TEXT
Description
Choose for crisp, clear shots that capture the brightness of sunlit beaches.
Reduces the blue cast typically associated with underwater lighting.
Capture indoor background lighting under low-light conditions.
Choose for vivid close-ups of flowers.
Take clear pictures of text or drawings in print.
M MANUAL
In this mode, you choose both shutter speed and aperture. If desired, exposure can be altered from the value suggested by the
camera.
Rotate the main-command dial to set the shutter speed or aperture. Press the
main-command dial to change the setting item between shutter speed and
aperture.
Shutter speed
M
c
2000
d
F5.6
Aperture
R Rotating the main-command dial changes the setting marked with d.
Q Noise in the form of randomly-spaced bright pixels may occur in long exposures.
Q The shutter speed is restricted depending on the ISO setting.
Q If the shutter speed is displayed in red at the selected aperture, photos will be taken
without the selected shutter speed.
42
More on Photography
Shooting Mode
Sub-command dial
When an option other than MANUAL is selected for focus mode
(P 62), you can use the sub-command dial to set aperture or
shutter speed.
R Rotating the sub-command dial changes the setting that is
marked with c.
R Press the main-command dial to change the setting item.
2000
d
2000
c
c
d
F5.6
F5.6
The Exposure Indicator
The amount the picture will be under- or over-exposed at current settings is shown by the exposure indicator.
M
More on Photography
c
2000
d
F5.6
43
Shooting Mode
A APERTURE PRIORITY AE
Choose the aperture using the main/sub-command dial, while the
camera adjusts shutter speed for optimal exposure.
Q If the correct exposure can not be achieved at the selected
aperture, shutter speed will be displayed in red. Adjust aperture until the correct exposure is achieved. If the subject is
outside the metering range of the camera, the shutter speed
display will show “---”. Press the shutter button halfway to
measure exposure again.
A
2000
F6.4
d
Aperture
S SHUTTER PRIORITY AE
Choose the shutter speed using the main/sub-command dial, while
the camera adjusts aperture for optimal exposure.
Q If the correct exposure can not be achieved at the selected
shutter speed, aperture will be displayed in red. Adjust shutter speed until the correct exposure is achieved. If the subject
is outside the metering range of the camera, the aperture
display will show “F ---”. Press the shutter button halfway to
measure exposure again.
Q If the shutter speed is displayed in red at the selected aperture, photos will be taken without the selected shutter speed.
44
S
2000
d
F6.4
Shutter speed
More on Photography
Shooting Mode
P PROGRAM AE
The camera sets exposure automatically.
Q If the subject is outside the metering range of the camera, the shutter speed and
aperture displays will show “---”. Press the shutter button halfway to measure exposure again.
Program Shift
Rotate the main/sub-command dial to choose the desired combination of shutter
speed and aperture. The default values can be restored by raising the flash or turning the camera off. To use program shift, turn the flash off. Furthermore, an option
other than AUTO must be selected for U DYNAMIC RANGE and N ISO.
Shutter speed
2000
More on Photography
F5.6
Aperture
45
Shooting Mode
C1/C2 CUSTOM MODE
In P, S, A, M and all EXR modes except R, the K CUSTOM SET
option in the shooting menu can be used to save current camera
and menu settings. These settings are recalled whenever the mode
dial is rotated to C1/C2 (custom mode).
Menu/setting
Settings saved
N ISO, O IMAGE SIZE, T IMAGE QUALITY, U DYNAMIC RANGE,
P FILM SIMULATION, d WB SHIFT, f COLOR, q SHARPNESS,
Shooting r HIGHLIGHT TONE, s SHADOW TONE, h NOISE REDUCTION,
menu
R INTELLIGENT DIGITAL ZOOM, b FACE DETECTION,
F FOCUS MODE, I FLASH, C PHOTOMETRY, D WHITE BALANCE,
R CONTINUOUS
Setup menu C AF ILLUMINATOR, j RAW
Macro mode (F), flash mode (N), program shift, shutter speed, aperture, monitor
Other
display options (DISP/BACK), exposure compensation (d)
Q Once the camera is turned off, R INTELLIGENT DIGITAL ZOOM is deactivated.
46
More on Photography
Focus Lock
To compose photographs with off-center subjects:
1 Focus: Position the subject in the focus frame and
press the shutter button halfway to lock focus and exposure. Focus and exposure will remain locked while
the shutter button is pressed halfway (AF/AE lock).
1000
F3.3
1000
F3.3
2 Recompose: Keep the button pressed halfway.
3 Shoot: Press the button all the way down.
More on Photography
47
Focus Lock
Autofocus
Although the camera boasts a high-precision autofocus system, it may be unable to
focus on the subjects listed below. If the camera is unable to focus, focus on another
subject at the same distance and use focus lock to recompose the photograph.
• Very shiny subjects such as mirrors or car bodies.
• Subjects that show little contrast with the background
• Fast-moving subjects.
(for example, subjects in clothing that is the same color
• Subjects photographed through a window or other re- as the background).
flective object.
• Subjects positioned in front of or behind a high-contrast
• Dark subjects and subjects that absorb rather than reflect object that is also in the focus frame (for example, a
light, such as hair or fur.
subject photographed against a backdrop of highly con• Insubstantial subjects, such as smoke or flame.
trasting elements).
48
More on Photography
d Exposure Compensation
To adjust exposure compensation when photographing
very bright, very dark, or high-contrast subjects, press
the selector up (d). Rotate the main/sub-command
dial to choose an exposure compensation value and
then press MENU/OK.
Choose positive (+) values
to increase exposure
Choose negative (–) values
to reduce exposure
R A d icon and exposure indicator are displayed at settings other than ±0. Exposure
compensation is not reset when the camera is turned off ; to restore normal exposure control, choose a value of ±0.
R Turn the flash off when using exposure compensation.
More on Photography
49
F Macro Mode (Close-ups)
For close-ups, press the selector left (F) and select F.
Rotate the zoom ring to compose pictures (P 26).
To exit macro mode, press the selector left (F) and select
OFF.
OFF
OFF
R Use of a tripod is recommended to prevent blur caused by camera shake.
R The shadow cast by the lens may appear in photographs taken with the flash at
very short ranges. Zoom out or increase the distance to the subject.
R Macro mode can be performed only when autofocus is used.
50
More on Photography
N Using the Flash (Super-Intelligent Flash)
When the flash is used, the camera’s Super-Intelligent Flash system instantly
analyzes the scene based on such factors as the brightness of the subject,
its position in the frame, and its distance from the camera. Flash output and
sensitivity are adjusted to ensure that the main subject is correctly exposed
while preserving the effects of ambient background lighting, even in dimly-lit
indoor scenes. Use the flash when lighting is poor, for example when shooting at night or indoors under low light.
1 Slide the flash pop-up switch to raise the flash.
More on Photography
51
N Using the Flash (Super-Intelligent Flash)
2 Press the selector right (N) and choose from the following flash modes:
Option
Description
The flash fires when required. Recommended in most
AUTO//K
AUTO
situations.
The flash fires whenever a picture is taken. Use for
N/L * backlit subjects or for natural coloration when shooting
in bright light.
Capture both the main subject and the background
O/M * under low light (note that brightly lit scenes may be
overexposed).
*
AUTO FLASH
According to
shooting conditions
* J icon indicates that Intelligent Face Detection and red-eye removal are on and will be
used to minimize “red-eye” caused by the flash reflecting from the retinas of portrait subjects.
R Lower the flash where flash photography is prohibited or to capture natural lighting
under dim light. We also recommend that you lower the flash when the camera is
off.
R If the flash will fire, p will be displayed when the shutter button is pressed halfway.
At slow shutter speeds, k will appear in the display to warn that pictures may be
blurred; use of a tripod is recommended.
R The flash may fire several times with each shot. Do not move the camera until
shooting is complete.
R The flash may cause vignetting.
52
More on Photography
h Using the Self-Timer
To use the self-timer, press the selector down (h) and
choose from the following options:
OFF
OFF
Option
T (OFF)
S (10 SEC)
R (2 SEC)
Description
Self-timer off.
The shutter is released ten seconds after the shutter button is pressed. Use for
self-portraits. The self-timer lamp on the front of the camera lights when the
timer starts and begins to blink shortly before the photo is taken.
The shutter is released two seconds after the shutter button is pressed. Use to
reduce blur caused by the camera moving when the shutter button is pressed.
The self-timer lamp will blink as the timer counts down.
More on Photography
53
The Fn Button
The role played by the Fn button can be selected using the F Fn BUTTON option.
The following options are available:
ISO (P 100)/IMAGE SIZE (P 101)/IMAGE QUALITY (P 101)/
RAW (P 128)/DYNAMIC RANGE (P 102)/FILM SIMULATION (P 103)/
PHOTOMETRY (P 107)/FOCUS MODE (P 62)/
FACE RECOGNITION (P 67)/FACE DETECTION (P 66)/
INTELLIGENT DIGITAL ZOOM (P 106)
R The F Fn BUTTON menu can also be displayed by pressing and holding the Fn
button.
54
More on Photography
The E-Fn Button
Press the E-Fn button to use the E-Fn (extended function) menu.
The each role played by the a button, the t button and the selector up,
down, left and right can be used in the E-Fn menu.
R Press the E-Fn button again to return to shooting mode.
■ Using the E-Fn BUTTON CUSTOM SETTING Menu
The following options are available:
ISO (P 100)/IMAGE SIZE (P 101)/IMAGE QUALITY (P 101)/RAW (P 128)/
DYNAMIC RANGE (P 102)/FILM SIMULATION (P 103)/
WHITE BALANCE (P 104)/CONTINUOUS (P 57)/PHOTOMETRY (P 107)/
FOCUS MODE (P 62)/FOCUS AREA (P 65)/FACE DETECTION (P 66)/
FACE RECOGNITION (P 67)/INTELLIGENT DIGITAL ZOOM (P 106)
1 Select E E-Fn BUTTON CUSTOM SETTING in the
E E-Fn BUTTON CUSTOM SETTING
shooting menu. The E E-Fn BUTTON CUSTOM SETTING menu is displayed.
PRESS THE BUTTON
TO CHANGE
THE FUNCTION.
SET
More on Photography
55
The E-Fn Button
2 Press the button to adjust.
E E-Fn BUTTON CUSTOM SETTING
ISO
IMAGE SIZE
IMAGE QUALITY
RAW
DYNAMIC RANGE
FILM SIMULATION
WHITE BALANCE
3 Highlight items and press the selector up or down to view options, then
highlight an option and press MENU/OK.
56
More on Photography
R Continuous Shooting
To capture motion in a series of pictures, press MENU/
OK, select R CONTINUOUS in the shooting menu, and
choose from the options listed in this section.
Option
B STILL IMAGE
I TOP n
P BEST FRAME CAPTURE
O AE BKT
W ISO BKT
X FILM SIMULATION BKT
Y DYNAMIC RANGE BKT
P
—
58
58
60
60
60
61
R The flash turns off automatically. The previously selected flash mode is restored
when B is selected for R CONTINUOUS.
R Frame rate varies with shutter speed.
R Focus and exposure are determined by the first frame in each series.
R The number of pictures that can be taken in a single burst varies with the scene
and camera settings. The number of pictures that can be recorded depends on the
memory available.
More on Photography
57
R Continuous Shooting
■ I TOP n
The camera takes photographs while the shutter button is pressed. To choose
the frame rate:
1 Press the selector left or right to choose a frame rate and
press MENU/OK to select and return to shooting mode.
LOW
■ P BEST FRAME CAPTURE
The camera takes a series of pictures, starting before and ending after the
shutter button is pressed.
1 Press the selector right when the camera is in shooting mode.
2 Highlight the current frame rate and press the selector right, then press
selector up or down to choose a new value and press MENU/OK to select.
Q Some frame rates may reduce the number of shots available.
3 Highlight the number of shots and press the selector
right. Press the selector up or down to choose the number of shots in each burst and left or right to choose
their distribution (the number on the left is taken before
and the number on the right after the shutter button
is pressed). Press MENU/OK when settings are complete
and press DISP/BACK to return to shooting mode.
58
Shots per burst
CONTINUOUS SHOOTING SETUP
SHUTTER
SET
16
8 FRAMES
CANCEL
Distribution
More on Photography
R Continuous Shooting
4 Take photographs. The camera begins recording while the shutter button
is pressed halfway, and completes the burst when the shutter button is
pressed all the way down. The illustration shows a burst of eight shots,
three before the shutter button is pressed and four after.
Shutter button
pressed halfway
Shutter button pressed all
the way down
“Before” shots
“After” shots
Q If the shutter button is pressed all the way down before the number of frames
selected for the “before” portion is recorded, the remaining frames will be taken
after the shutter button is pressed all the way down.
Q If the shutter button is pressed halfway for an extended period, the camera may
record the burst before the shutter button is pressed all the way down.
More on Photography
59
R Continuous Shooting
■ O AE BKT
Each time the shutter button is pressed, the camera takes three shots: one using the metered value for exposure, the second overexposed by the amount
selected for the selector left or right, and the third underexposed by the same
amount (the camera may not be able to use the selected bracketing increment if the amount of over- or under- exposure exceeds the limits of the exposure metering system).
■ W ISO BKT
Press the selector left or right to highlight a bracketing amount. Each time
the shutter is released, the camera will take a picture at the current sensitivity
(P 100) and process it to create two additional copies, one with sensitivity raised
and the other with sensitivity lowered by the selected amount (regardless of
the amount selected, sensitivity will not exceed ISO 1600 or fall below ISO
200).
■ X FILM SIMULATION BKT
Each time the shutter button is pressed, the camera takes one shot and processes it to create three copies with different P FILM SIMULATION settings
(P 103): c PROVIA/STANDARD for the first, d Velvia/VIVID for the second,
and e ASTIA/SOFT for the third.
60
More on Photography
R Continuous Shooting
■ Y DYNAMIC RANGE BKT
Each time the shutter button is pressed, the camera takes three shots at different U DYNAMIC RANGE settings (P 102): V 100% for the first, W 200%
for the second, and X 400% for the third (N ISO can not exceed 3200; values less than 400 are not available when O is selected for O IMAGE SIZE).
More on Photography
61
F Focus Mode
To choose how the camera focuses, press MENU/OK to
display the shooting menu and choose from the FOCUS
MODE options.
The following options are available:
Mode
Description
Focus manually using the sub-command dial. Rotate the sub-command dial
left to reduce the focus distance, right to increase. Choose for manual control
of focus or in situations in which the camera is unable to focus using autofocus
M MANUAL (P 47). Intelligent Face Detection turns off automatically.
Reduce focus
distance
t AREA
s MULTI
62
Increase focus distance
Choose the focus area manually (P 65).
When the shutter button is pressed halfway, the camera detects high-contrast
subjects near the center of the frame and selects the focus area automatically.
More on Photography
F Focus Mode
Mode
Description
The camera continually adjusts focus to reflect changes in the distance to the
u CONTINUsubject even when the shutter button is not pressed halfway (note that this inOUS
creases the drain on the battery). Choose for moving subjects.
Position the subject in the center focus area and press the selector left. Focus will
x TRACKING
track the subject as it moves through the frame.
R Manual Focus
• Use of a tripod is recommended. Focus may be affected if the camera moves.
• Use the I FOCUS CONTROL DIAL option in the setup menu (P 130) to reverse the
direction of rotation of the sub-command dial.
• The camera will not focus if the sub-command dial is rotated past infinity.
• While the F FOCUS MODE is selected to M MANUAL, macro mode cannot be
used.
• To focus using autofocus, press the selector left. This can be used to quickly focus on
a chosen subject in manual focus mode.
R Note that in u and x modes, the camera focuses continuously, increasing the
drain on the battery, and that the sound of the camera focusing may be audible.
R If a face is detected when u is selected, a o icon will be displayed and the camera will continuously adjust focus to maintain focus on the face.
More on Photography
63
F Focus Mode
j FOCUS CHECK
If ON is selected for j FOCUS CHECK
in the setup menu (P 125), rotating the
sub-command dial magnifies the view
in the LCD monitor.
R The focus check area can be scrolled
(P 65).
64
M
2000
c
d
F6.4
M
2000
c
d
F6.4
More on Photography
Focus Frame Selection
When t AREA is selected for F FOCUS MODE in the
shooting menu, focus position can be changed. Press
MENU/OK to select F FOCUS AREA in the shooting menu
and then press the selector up, down, left or right. The setting takes effect when you press the MENU/OK button again.
Focus point
Focus frame
When framing a picture in the LCD monitor, you can
choose the size of the focus frame. Press MENU/OK, select
F FOCUS AREA in the shooting menu and then rotate
the main-command dial. The frame size can be reduced up
to 50% or enlarged up to 150% (returned to 100% by pressing the main-command dial). The setting takes effect when
you press the MENU/OK again.
More on Photography
65
b Intelligent Face Detection
Intelligent Face Detection sets focus and exposure for human faces anywhere
in the frame, preventing the camera from focusing on the background in
group portraits. Choose for shots that emphasize portrait subjects.
To use Intelligent Face Detection, press MENU/OK to display the shooting menu and select ON for b FACE
DETECTION SET-UP > FACE DETECTION. Faces can be
detected with the camera in vertical or horizontal orientation; if a face is detected, it will be indicated by a green
border. If there is more than one face in the frame, the
camera will select the face closest to the center; other
faces are indicated by white borders.
Q In some modes, the camera may set exposure for the frame as a whole rather than
the portrait subject.
Q If the subject moves as the shutter button is pressed, their face may not be in the
area indicated by the green border when the picture is taken.
66
More on Photography
n Face Recognition
The camera can store information on the face and personal
details (name, relationship, and birth date) of portrait subjects and assign these subjects priority for Intelligent Face
Detection or display their names and other information
during playback.
Happy Birthday!
Adding New Faces
Follow the steps below to add faces to the face recognition database.
1 Select REGISTER.
Select REGISTER for b FACE DETECTION SET-UP > FACE RECOGNITION.
R To disable face recognition, select OFF.
2 Take a photograph.
After checking that the subject is facing the camera,
frame the subject using the guides and take the photograph.
R If an error is displayed, take the photograph again.
More on Photography
REGISTER FACE
CAPTURE THE FACE
ALONG WITH THE GUIDLINE
CANCEL
67
n Face Recognition
3 Enter face recognition data.
Press MENU/OK to display face recognition data and enter the following information:
• NAME: Enter a name of up to 14 characters and press MENU/OK.
• BIRTHDAY: Enter the subject’s date of birth and press MENU/OK.
• CATEGORY: Choose the option that describes your relationship to the subject and press MENU/OK.
R If you attempt to zoom in on the face of a person indicated by a green border
in the face recognition database on their birthday, the camera will display their
name and the message “Happy Birthday!”
68
More on Photography
n Face Recognition
Viewing, Editing, and Deleting Existing Data
Follow the steps below to view, edit, or delete face recognition data.
1 Select VIEW & EDIT for n FACE RECOGNITION.
2 Select a face.
3 View or edit face recognition data.
The name, category, or birth date can be edited as described in Step 3 of
“Adding New Faces” (P 68). To retake the photo, select REPLACING IMAGE
and shoot a new portrait as described above.
R To delete face recognition data for the selected subject, select ERASE.
Adding Faces Automatically
To automatically add frequently-photographed subjects to the face recognition database, select ON for AUTO REGISTRATION in the face recognition
menu. If the camera detects a face that has been photographed many times
without being added to the database, it will display a message prompting you
to create a new face recognition entry. Press MENU/OK and enter face recognition data.
R The camera may sometimes fail to recognize new faces automatically. If necessary,
faces can be added manually using the REGISTER option.
More on Photography
69
n Face Recognition
Face Recognition
The camera can store up to eight faces. If you attempt to add a ninth face, a confirmation dialog will be displayed; use ERASE to make room for new faces by deleting
existing data. AUTO REGISTRATION is disabled if there are already data for eight
faces.
When Intelligent Face Detection (P 66) is on and the frame contains multiple subjects from the face recognition database, the camera displays the name of the subject that will be used to set focus and exposure (the subject shown by the green
frame). If no name is entered, the camera will show “---”. Subjects identified using
face recognition but not used to set focus and exposure are shown by orange
frames, other subjects by white frames.
Q The camera may fail to identify subjects in the face recognition database if they
are not facing the camera or are only partly in the frame, or if details of the subjects’ faces or expressions differ markedly from those in the database.
70
More on Photography
More on Playback
Playback Options
To view the most recent picture in the LCD monitor, press the a button.
100-0001
1 / 1000
F4.
F4.5
4.5
-1 2 3
Press the selector right to view pictures in the order recorded, left to view
pictures in reverse order. Keep the selector pressed to scroll rapidly to the
desired frame.
R Pictures taken using other cameras are indicated by a m (“gift image”) icon during
playback.
Continuous Shooting
In the case of pictures taken in continuous shooting mode, only the first frame
of each series will be displayed. Press the selector down to view the other
pictures in the series.
I Favorites: Rating Pictures
To rate the picture currently displayed in full-frame playback, press DISP/BACK
and press the selector up and down to select from zero to five stars.
71
Playback Options
Playback Zoom
Rotate the main-command dial to zoom on pictures displayed in single-frame
playback. When the picture is zoomed in, the selector can be used to view
areas of the image not currently visible in the display.
Zoom indicator
Navigation window shows
portion of image currently
displayed in LCD monitor
Press DISP/BACK to exit zoom.
R If the pictures before or after the current picture are the same size as the current
picture, you can rotate the sub-command dial to view the other pictures without
changing the zoom ratio. This option is not available if the pictures are not the same
size as the current picture.
R The maximum zoom ratio varies with image size. Playback zoom is not available
with cropped or resized copies saved at a size of a or smaller.
72
More on Playback
Playback Options
Multi-Frame Playback
To change the number of images displayed, rotate the main-command dial.
Rotate the main-command dial to the left to increase the number of images
displayed to two, nine, or one hundred, and rotate it to the right to view fewer
images.
100-0001
When two or more images are displayed, use the selector to highlight images
and press MENU/OK to view the highlighted image full frame. In the nine- and
hundred-frame displays, use the selector to view more pictures.
More on Playback
73
A Deleting Pictures
To delete individual pictures, multiple selected pictures, or all
pictures, press MENU/OK, select A ERASE, and choose from
the options below. Note that deleted pictures can not be recovered. Copy important pictures to a computer or other storage device before proceeding.
PLAYBACK
Y
MENU
ERASE
BACK
FRAME
SELECTED FRAMES
ALL FRAMES
EXIT
Option
Description
Press the selector left or right to scroll through pictures and press MENU/OK to delete
FRAME
the current picture (a confirmation dialog is not displayed).
Highlight pictures and press MENU/OK to select or deselect (pictures in photobooks
SELECTED
or print orders are shown by S). When the operation is complete, press DISP/BACK
FRAMES
to display a confirmation dialog, then highlight OK and press MENU/OK to delete the
selected pictures.
A confirmation dialog will be displayed; highlight OK and press MENU/OK to delete all
unprotected pictures (if a memory card is inserted, only the pictures on the memory
ALL FRAMES card will be affected; the pictures in internal memory are only deleted if no memory
card is inserted). Pressing DISP/BACK cancels deletion; note that any pictures deleted
before the button was pressed can not be recovered.
R Protected pictures can not be deleted. Remove protection from any pictures you
wish to delete (P 117).
R If a message appears stating that the selected images are part of a DPOF print order,
press MENU/OK to delete the pictures.
74
More on Playback
b Image Search
Search for pictures.
1 Select b IMAGE SEARCH in the playback menu, highlight one of the following search criteria, and press MENU/OK:
• BY DATE: Search by date.
• BY FACE: Search for faces from the face recognition database.
• BY I FAVORITES: Search by rating.
• BY SCENE: Search by scene.
• BY TYPE OF DATA: Find all still pictures or all movies.
• BY UPLOAD MARK: Find all pictures selected for upload to a specified destination.
2 Select a search condition. Only pictures that match the search condition
will be displayed. To delete or protect selected pictures or to view the
search results in a slide show, press MENU/OK and choose A ERASE (P 74),
D PROTECT (P 117), or I SLIDE SHOW (P 114).
More on Playback
75
m PhotoBook Assist
Create books from your favorite photos.
Creating a PhotoBook
1 Select NEW BOOK for m PHOTOBOOK ASSIST in the playback menu
and choose from the following options:
• SELECT FROM ALL: Choose from all available pictures.
• SELECT BY IMAGE SEARCH: Choose from pictures matching selected search
conditions (P 75).
R Movies, 3D photos, and photographs a or smaller can not be selected for photobooks.
2 Scroll through the images and press the selector up to select or deselect.
To display the current image on the cover, press the selector down. Press
MENU/OK to exit when the book is complete.
R The first picture selected becomes the cover image. Press the selector down to
select a different image for the cover.
3 Select COMPLETE PHOTOBOOK (to select all photos or all photos matching the specified search conditions for the book, choose SELECT ALL).
The new book will be added to the list in the photobook assist menu.
Q Books can contain up to 300 pictures.
Q Books that contain no photos are automatically deleted.
76
More on Playback
m PhotoBook Assist
Viewing Photobooks
Highlight a book in the photobook assist menu and press MENU/OK to display
the book, then press the selector left or right to scroll through the pictures.
Editing and Deleting Photobooks
Display the photobook and press MENU/OK. The following options will be displayed; select the desired option and follow the on-screen instructions.
• EDIT: Edit the book as described in “Creating a PhotoBook” (P 76).
• ERASE: Delete the book.
Photobooks
Photobooks can be copied to a computer using the supplied MyFinePix Studio software.
More on Playback
77
Viewing Panoramas
If you press the selector down when a panorama is displayed full frame, the
camera will play back the picture from left to right or from bottom to top. To
pause playback, press the selector down; press the selector down again to
resume. To exit to full-frame playback, press the selector up while panorama
playback is in progress. Once displayed in full-frame playback, panoramas can
be zoomed in or out using the main-command dial or deleted by pressing the
selector up (b).
PLAY
STOP
PAUSE
R z panoramas play back in an endless loop (P 35); the playback direction can be
controlled by pressing the selector left or right. The camera will not turn off automatically while playback is in progress (P 126).
78
More on Playback
Viewing Photo Information
Photo information can be viewed by pressing DISP/BACK to cycle through indicators (P 7) until the following display appears:
100-0001
4:3 N
ISO 400
F4.5
1/250
: STD
: OFF
:
: -1 2 3
12/31/2050 10 : 00 AM
q Dynamic range w Image size and quality
e Sensitivity
r Shutter speed/aperture
t Film simulation y Flash mode
u White balance
i Exposure compensation
o Frame number
!0 Picture (overexposed areas blink on and off )
!1 Histogram
Additional photo information
Additional photo information can be viewed by pressing the
E-Fn button. Press the E-Fn button to cycle the display.
D-RANGE
COLOR
HIGHLIGHTTONE
SHADOWTONE
SHARPNESS
FILM SIM.
WHITE BALANCE
: AUTO
: STD
: STD
: STD
: --: Velvia
: AUTO
R The active focus point is shown by a “+” icon.
More on Playback
79
Viewing Photo Information
Zooming in on the Focus Point
Press the main-command dial to zoom in on the focus point.
Press DISP/BACK or MENU/OK to return to full-frame playback.
80
More on Playback
Movies
Recording Movies
Press t to shoot a movie. During recording, the following indicators will be
displayed and sound will be recorded via the built-in microphone (be careful
not to cover the microphone during recording).
R icon
98
18m39s
Number of photos that
can be taken during
recording
Time remaining
To end recording, press t again. Recording ends automatically when the
movie reaches maximum length or memory is full. For information on the
maximum footage that can be recorded, see page 146.
Automatic Scene Selection
In R mode, the camera selects the scene according to shooting conditions and the type of subject: d (portraits), d (poorly-lit landscapes), f (poorly-lit portraits), c (landscapes),
e (close-ups), g (backlit portraits), or a (other subjects).
98
18m39s
Scene icon
81
Recording Movies
Taking Photographs During Recording
Press the shutter button to take a photograph during recording.
R The method used to record photographs can be selected using the W MOVIE SET-UP >
STILL SHOOTING IN MOVIE option (P 110).
R The photo is saved separately from the movie and does not appear as part of the movie.
Q Photos can not be taken while a high-speed movie is being recorded.
Q The number of photos that can be taken is limited.
R Zoom can be adjusted while recording is in progress.
R If the subject is poorly lit, the AF-assist lamp may light to assist the focus operation.
To turn the AF-assist lamp off, select OFF for C AF ILLUMINATOR (P 128).
R Focus, exposure, and white balance are adjusted automatically throughout recording. The color and brightness of the image may vary from that displayed before
recording begins.
R Sounds made by the camera may be recorded.
Q The indicator lamp lights while movies are being recorded. Do not open the battery chamber during shooting or while the indicator lamp is lit. Failure to observe
this precaution could prevent the movie from being played back.
Q Vertical or horizontal streaks may appear in movies containing very bright subjects.
This is normal and does not indicate a malfunction.
Q The temperature of the camera may rise if it is used to record movies for an extended period or if the ambient temperature is high. This is normal and does not
indicate a malfunction.
Q The mode selected may vary with shooting conditions.
82
Movies
Recording Movies
Movie Frame Size
Before recording, select a frame size using the W MOVIE SET-UP > MOVIE
MODE option.
Option
i 1920 × 1080
h 1280 × 720
f 640 × 480
k 640 × 480 (70 fps)
k 320 × 240 (120 fps)
k 320 × 112 (200 fps)
Movies
Description
Full HD (High Definition).
High Definition.
Standard definition.
High speed movie. Sound is not recorded, and focus, exposure, and white
balance are not adjusted automatically. Black bands appear at the top and
bottom of movies recorded at k 320 × 112.
83
Viewing Movies
During playback, movies are displayed in the LCD monitor
as shown at right. The following operations can be performed while a movie is displayed:
Option
Description
Press the selector down to start playback. Press again to
Start/pause
pause. While playback is paused, you can press the selecplayback
tor left or right to rewind or advance one frame at a time.
End playback/
Press the selector up to end playback.
delete
Press the selector left or right to adjust playback speed durAdjust speed
ing playback.
Press MENU/OK to pause playback and display volume controls. Press the selector up or down to adjust the volume
Adjust volume and press MENU/OK to exit. Volume can also be adjusted
using the b SOUND SET-UP > PLAYBACK VOLUME option (P 124).
100-006
12 / 31 / 2050
PLAY
10 : 00 AM
Playback Speed
Press the selector left or right to adjust playback speed. Speed is Arrow
shown by the number of arrows (M or N).
STOP
5m42s
PAUSE
Q Do not cover the speaker during playback.
84
Movies
Connections
Viewing Pictures on TV
Connect the camera to a TV to show pictures to a group.
1 Turn the camera off and connect an optional A/V cable as shown below.
Insert into
USB multi-connector
Connect yellow plug to video-in jack
Connect white plug to audio-in jack
R Image quality drops during movie playback.
85
Viewing Pictures on TV
Connecting the Camera to High Definition (HD) TVs
An HDMI cable (available from third-party suppliers) can be used to connect the
camera to High Definition (HD) devices (playback only). The USB and A/V cables
can not be used while an HDMI cable is connected.
Insert into HDMI connector
HDMI mini connector
Insert into HDMI
connector
R When an HDMI cable is connected, pictures and sound are played back on the TV.
Q When connecting cables, be sure the connectors are fully inserted.
2 Tune the television to the video or HDMI input channel. See the documentation supplied with the television for details.
3 Press the a button for about a second to turn the camera on. The camera
monitor turns off and pictures and movies are played back on the TV. Note
that the camera volume controls have no effect on sounds played on the
TV; use the television volume controls to adjust the volume.
86
Connections
Printing Pictures via USB
If the printer supports PictBridge, the camera can be connected
directly to the printer as shown below and pictures can be printed
without first being copied to a computer. Note that depending on
the printer, not all the functions described below may be supported.
1 Connect the supplied USB cable as shown and turn the printer on.
2 Turn the camera on.
3 Press the selector left or right to display a picture you wish to print.
4 Press the selector up or down to choose the number of copies (up to 99).
5 Repeat steps 3–4 to select additional pictures. Press MENU/OK to display a
confirmation dialog when settings are complete.
Connections
87
Printing Pictures via USB
6 Press MENU/OK to start printing. Printing can be interrupted by pressing
DISP/BACK, but note that some printers may not respond immediately. If the
printer stops before printing is complete, turn the camera off and then on
again.
7 After confirming that PRINTING has cleared from the camera display, turn
the camera off and disconnect the USB csable.
R Pictures can be printed from internal memory or a memory card that has been
formatted in the camera.
R If no pictures are selected, the camera will print one copy of the current picture.
R Page size, print quality, and border selections are made using the printer.
Printing the Date of Recording
To print the date of recording on pictures, press DISP/BACK in the PictBridge display
and select PRINT WITH DATE s in the PictBridge menu (to print pictures without
the date of recording, select PRINT WITHOUT DATE). Some printers do not support
date printing. See the printer manual for details.
88
Connections
Printing Pictures via USB
Printing the DPOF Print Order
The K PRINT ORDER (DPOF) option can be used to create a digital “print
order” for PictBridge-compatible printers (P 87) or devices that support DPOF.
DPOF
DPOF (Digital Print Order Format) is a standard that allows pictures to be
printed from “print orders” stored in internal memory or on a memory card.
The information in the order includes the pictures to be printed and the
number of copies of each picture.
1 Select playback mode and press MENU/OK to display the playback menu.
2 Highlight K PRINT ORDER (DPOF) and press MENU/OK.
3 Highlight one of the following options and press MENU/OK:
• WITH DATE s: Print the date of recording on pictures.
• WITHOUT DATE: Do not print the date of recording on pictures.
R Some printers do not support date printing. See the printer manual for details.
4 Press the selector left or right to display a picture you wish to add to or
remove from the print order.
Connections
89
Printing Pictures via USB
5 Press the selector up or down to choose the number of copies (up to 99).
To remove a picture from the print order, press the selector down until the
number of copies is zero.
6 Repeat Steps 4 – 5 to complete the print order and press MENU/OK when
settings are complete.
7 A confirmation dialog will be displayed. Press MENU/OK to save the print
order.
R Remove the memory card to create or modify a print order for the pictures in
internal memory.
R Print orders can contain a maximum of 999 pictures.
R If a memory card is inserted containing a print order created by another camera,
a message will be displayed. Create a new print order as described above.
90
Connections
Viewing Pictures on a Computer
The supplied software can be used to copy pictures to a computer, where
they can be stored, viewed, organized, and printed. Before proceeding, install
the software as described below. Do NOT connect the camera to the computer
until installation is complete.
Windows: Installing MyFinePix Studio
1 Confirm that the computer meets the following system requirements:
Windows 7 (SP 1)/Windows Vista (SP 2) 1
3 GHz Pentium 4 or better
(2.4 GHz Core 2 Duo or better) 2
Windows XP (SP 3) 1
2 GHz Pentium 4 or better
CPU
(2.4 GHz Core 2 Duo or better) 2
512 MB or more
RAM
1 GB or more
(1 GB or more) 2
Free disk space
2 GB or more
Supports DirectX 9 or later
Supports DirectX 7 or later
GPU
(recommended
recommended))
(required; performance not guaranteed with other GPUs)
GPUs)
Video
1,024 × 768 pixels or more with 24-bit color or better
• Built-in USB port recommended. Operation is not guaranteed with other
USB ports.
• .NET Framework 3.5 Service Pack 1 required when uploading images or usOther
ing Map Viewer.
• Internet connection (broadband recommended) required to install
.NET Framework (if necessary), to use auto update feature, and when performing such tasks as sharing pictures on-line or via e-mail.
1 Other versions of Windows are not supported. Only pre-installed operating systems are
supported; operation is not guaranteed on home-built computers or computers that have
been upgraded from earlier versions of Windows.
2 Recommended when displaying HD movies.
Connections
91
Viewing Pictures on a Computer
2 Start the computer. Log in to an account with administrator privileges
before proceeding.
3 Exit any applications that may be running and insert the installer CD in a
CD-ROM drive.
Windows 7/Windows Vista
If an AutoPlay dialog is displayed, click SETUP.EXE. A “User Account Control”
dialog will then be displayed; click Yes (Windows 7) or Allow (Windows Vista).
The installer will start automatically; click Install MyFinePix Studio and
follow the on-screen instructions to install MyFinePix Studio and RAW FILE
CONVERTER.
If the Installer Does Not Start Automatically
If the installer does not start automatically, select Computer or My Computer
from the Start menu, then double-click the FINEPIX CD icon to open the FINEPIX
CD window and double-click setup or SETUP.EXE.
92
Connections
Viewing Pictures on a Computer
4 If prompted to install Windows Media Player or DirectX, follow the onscreen instructions to complete installation.
5 Remove the installer CD from the CD-ROM drive when installation is complete. Store the installer CD in a dry location out of direct sunlight in case
you need to re-install the software.
Installation is now complete. Proceed to “Connecting the Camera” (P 96).
Connections
93
Viewing Pictures on a Computer
Macintosh: Installing FinePixViewer
1 Confirm that the computer meets the following system requirements:
PowerPC or Intel (Core 2 Duo or better) *
Pre-installed copies of Mac OS X version 10.5–10.6 (visit http://www.fujifilm.
OS
com/support/digital_cameras/compatibility/ for more information). Mac OS X
version 10.7 and later not supported.
RAM
256 MB or more (1 GB or more) *
A minimum of 200 MB required for installation with 400 MB available when
Free disk space
FinePixViewer is running
Video
800 × 600 pixels or more with thousands of colors or better
Built-in USB port recommended. Operation is not guaranteed with other USB
Other
ports.
CPU
* Recommended when displaying HD movies.
2 After starting the computer and quitting any applications that may be running, insert the installer CD in a CD-ROM drive and double-click Installer
for Mac OS X.
Viewing RAW Images
RAW FILE CONVERTER software is required to view RAW images on a computer.
To install RAW FILE CONVERTER, double-click SILKYRFCEXInstaller. RAW FILE
CONVERTER is supported under Mac OS X versions 10.5 to 10.7.
94
Connections
Viewing Pictures on a Computer
3 An installer dialog will be displayed; click Installing FinePixViewer to start
installation. Enter an administrator name and password when prompted
and click OK, then follow the on-screen instructions to install FinePixViewer.
Click Exit to quit the installer when installation is complete.
4 Remove the installer CD from the CD-ROM drive. Note that you may be
unable to remove the CD if Safari is running; if necessary, quit Safari before
removing the CD. Store the installer CD in a dry location out of direct sunlight in case you need to re-install the software.
5 Mac OS X 10.5: Open the “Applications” folder, start Image Capture, and select Preferences… from the Image Capture application menu. The Image Capture preferences dialog will be displayed; choose Other… in the
When a camera is connected, open menu, then select FPVBridge in the
“Applications/FinePixViewer” folder and click Open. Quit Image Capture.
Mac OS X 10.6: Connect the camera and turn it on. Open the “Applications”
folder and start Image Capture. The camera will be listed under DEVICES;
select the camera and choose FPVBridge from the Connecting this camera opens menu and click Choose. Quit Image Capture.
Installation is now complete. Proceed to “Connecting the Camera” (P 96).
Connections
95
Viewing Pictures on a Computer
Connecting the Camera
1 If the pictures you wish to copy are stored on a memory card, insert the
card into the camera.
R Windows users may require the Windows CD when starting the software for
the first time.
Q Loss of power during transfer could result in loss of data or damage to internal
memory or the memory card. Charge the battery before connecting the camera.
2 Turn the camera off and connect the supplied USB cable as shown, making sure the connectors are fully inserted. Connect the camera directly to
the computer; do not use a USB hub or keyboard.
3 Press the a button for about a second to turn the camera on and follow
the on-screen instructions to copy pictures to the computer. To exit without copying pictures, click Cancel.
96
Connections
Viewing Pictures on a Computer
For more information on using the supplied software, start the application
and select the appropriate option from the Help menu.
Q If a memory card containing a large number of images is inserted, there may be a
delay before the software starts and you may be unable to import or save images.
Use a memory card reader to transfer pictures.
Q Make sure that the computer does not display a message stating that copying is in
progress and that the indicator lamp is out before turning the camera off or disconnecting the USB cable (if the number of images copied is very large, the indicator
lamp may remain lit after the message has cleared from the computer display).
Failure to observe this precaution could result in loss of data or damage to internal
memory or the memory card.
Q Disconnect the camera before inserting or removing memory cards.
Q In some cases, it may not be possible to access pictures saved to a network server
using the supplied software in the same way as on a standalone computer.
Q The user bears all applicable fees charged by the phone company or Internet service provider when using services that require an Internet connection.
Connections
97
Viewing Pictures on a Computer
Disconnecting the Camera
After confirming that the indicator lamp is out, turn the camera off and disconnect
the USB cable.
Uninstalling the Supplied Software
Only uninstall the supplied software when it is no longer required or before beginning reinstallation. After quitting the software and disconnecting the camera, drag
the “FinePixViewer” folder from “Applications” into the Trash and select Empty Trash
in the Finder menu (Macintosh), or open the control panel and use “Programs and
Features” (Windows 7/Windows Vista) or “Add or Remove Programs” (Windows XP) to
uninstall MyFinePix Studio. Under Windows, one or more confirmation dialogs may
be displayed; read the contents carefully before clicking OK.
98
Connections
Menus
Using the Menus: Shooting Mode
Using the Shooting Menu
1 Display the shooting menu.
1.1 Press MENU/OK during shooting to display the
shooting menu.
1.2 Press the selector left to highlight the current tab.
Tab
P SHOOTING MENU
1.3 Press the selector up or down to highlight the tab
containing the desired option.
EXIT
1.4 Press the selector right to place the cursor in the menu.
2 Adjust settings.
Highlight items and press the selector right to view options, then highlight an option and press MENU/OK. Press DISP/BACK to exit when settings
are complete.
99
Using the Menus: Shooting Mode
Shooting Menu Options
A SCENE POSITION
Choose a scene for SP mode (P 41).
(default: h)
A E MODE
Choose an option for E mode (P 31).
A Adv. MODE
Choose an advanced shooting mode (P 33).
(default: R)
(default: ADVANCED FILTER)
(default: AUTO)
N ISO
Control the camera’s sensitivity to light. Higher values can reduce blur; note, however, that mottling may appear in pictures taken at high sensitivities.
100
Bright
Less noticeable
Option
AUTO
AUTO (3200) / AUTO (1600) /
AUTO (800) / AUTO (400)
12800 / 6400 / 5000 /
4000 / 3200 / 2500 / 2000 /
1600 / 1250 / 1000 / 800 /
640 / 500 / 400 / 320 / 250 /
200 / 100
100
ISO
Scene
Noise (mottling)
12800
Dark
More noticeable
Description
Sensitivity is adjusted automatically in response to shooting conditions.
As above, except that sensitivity will not be raised above the value in
parentheses.
Sensitivity is set to the specified value, which is shown in the display.
Menus
Using the Menus: Shooting Mode
O IMAGE SIZE
Choose the image size and aspect ratio at which pictures are recorded. Large pictures can be printed at large sizes with no drop in quality,
while small pictures require less memory, allowing more pictures to be
recorded.
(default: O 4:3)
O4:3
Size
Aspect ratio
Size Versus Aspect Ratio
Size
Option
O
P
Q
Prints at sizes up to
34 × 25 cm (13.5 × 10 in.)
24 × 18 cm (9.5 × 7 in.)
17 × 13 cm (7 × 5 in.)
Aspect ratio
4 : 3: Pictures have the same proportions as the camera display.
3 : 2: Pictures have the same proportions as a frame of 35 mm film.
16 : 9: Suited for display on High Definition (HD) devices.
1 : 1: Pictures are square.
T IMAGE QUALITY
Choose how much image files are compressed.
Option
FINE
NORMAL
Menus
(default: FINE)
Description
Low compression. Select for higher image quality.
High compression. Select this option to store more pictures.
101
Using the Menus: Shooting Mode
(default: AUTO)
U DYNAMIC RANGE
Control contrast. Higher values are recommended for scenes that include both sunlight and
deep shade or for increased contrast with such subjects as sunlight on water, brightly-lit autumn
leaves, portraits taken against a blue sky, and white objects or people wearing white; note, however, that mottling may appear in pictures taken at higher values. If AUTO is selected, the camera will automatically select values between 100% and 400% in response to shooting conditions.
Option
Description
V 100% Increase contrast when shooting indoors or under overcast skies.
AUTO W 200%
X 400%
Y 800%
Reduce loss of detail in highlights and shadows when photographing highcontrast scenes.
Z 1600%
R Z 1600% and Y 800% are available only when D-RANGE PRIORITY is selected in
E mode and an option other than d Velvia/VIVID or e ASTIA/SOFT is selected for
P FILM SIMULATION.
102
Menus
Using the Menus: Shooting Mode
P FILM SIMULATION
Simulate the effects of different types of film.
(default: c)
Option
Description
Standard color reproduction. Suited to a wide range of subjects, from
c (PROVIA/STANDARD)
portraits to landscapes.
A high-contrast palette of saturated colors, suited to nature photod (Velvia/VIVID)
graphs.
A soft-toned palette of less saturated colors.
e (ASTIA/SOFT)
Take pictures in black and white.
b (MONOCHROME)
Take black-and-white pictures with slightly increased contrast. This
e (MONOCHROME + Ye FILTER)
setting also slightly tones down the brightness of the sky.
Take black-and-white pictures with increased contrast. This setting
d (MONOCHROME + R FILTER)
also tones down the brightness of the sky.
f (MONOCHROME + G FILTER) Soften skin tones in black-and-white portraits.
Take pictures in sepia.
f (SEPIA)
Menus
103
Using the Menus: Shooting Mode
(default: AUTO)
D WHITE BALANCE
If AUTO does not produce natural colors (for example, when taking close-ups), select h and
measure a value for white balance or choose the option that matches the light source.
Option
AUTO
h
k
i
j
k
l
m
n
g
104
Description
White balance adjusted automatically.
Measure a value for white balance.
Selecting this option displays a list of color temperatures; highlight a temperature
and press MENU/OK.
For subjects in direct sunlight.
For subjects in the shade.
Use under “daylight” fluorescent lights.
Use under “warm white” fluorescent lights.
Use under “cool white” fluorescent lights.
Use under incandescent lighting.
For underwater photography
Menus
Using the Menus: Shooting Mode
D WHITE BALANCE (Continued)
(default: AUTO)
h: Custom White Balance
Choose h to adjust white balance for unusual lighting conditions. White balance measurement options will be displayed; frame a white object so that it fills the display and press the
shutter button all the way down to measure white balance.
• If “COMPLETED!” is displayed, press MENU/OK to set white balance to the measured value.
• If “UNDER” is displayed, raise exposure compensation (P 49) and try again.
• If “OVER” is displayed, lower exposure compensation and try again.
R For greater precision, adjust P FILM SIMULATION, N ISO, and U DYNAMIC RANGE
before measuring white balance.
R At settings other than h, auto white balance is used with the flash.
R Results vary with shooting conditions. Play pictures back after shooting to check colors in
the display.
k: Color Temperature
Color temperature is an objective measure of the color of a light source, expressed in Kelvin
(K). Light sources with a color temperature close to that of direct sunlight appear white; light
sources with a lower color temperature have a yellow or red cast, while those with a higher
color temperature are tinged with blue. You can match color temperature to the light source
as shown in the following table, or choose options that differ sharply from the color of the
light source to make pictures “warmer” or “colder”.
Choose for redder light sources
or “colder” pictures
2,000 K
Candlelight
Sunset/sunrise
Menus
Choose for bluer light sources
or “warmer” pictures
15,000 K
Blue sky
5,000 K
Direct sunlight
Shade
105
Using the Menus: Shooting Mode
d WB SHIFT
White balance can be fine-tuned. Adjust the selected color axis (R–Cy=Red-Cyan or B-Ye=Blue–
Yellow) by +9 to –9 in increments of one.
f COLOR
Adjust color density.
(default: MID)
q SHARPNESS
Choose whether to sharpen or soften outlines.
(default: STD)
r HIGHLIGHT TONE
Adjust the appearance of highlights.
(default: STD)
s SHADOW TONE
Adjust the appearance of shadows.
(default: STD)
h NOISE REDUCTION
Choose the amount of noise reduction.
(default: STD)
(default: OFF)
R INTELLIGENT DIGITAL ZOOM
If ON is selected, intelligent digital zoom magnifies the image to 2× while processing it for sharp,
high-resolution results.
R
R
R
R
R
Intelligent digital zoom may end when another mode is selected.
Intelligent digital zoom may sometimes produce lower quality images than optical zoom.
The time needed to record images increases.
The effects are not visible in the display during shooting.
Intelligent digital zoom is not available in continuous mode or during movie recording.
R CONTINUOUS
(default: B)
Capture motion in a series of pictures ((P
P 57). Choose from B, I, P, O, W, X and Y.
106
Menus
Using the Menus: Shooting Mode
Z ADVANCED ANTI BLUR
Select ON to enable advanced anti blur in R mode (P 32).
(default: ON)
b FACE DETECTION SET-UP
Adjust face detection and face recognition options.
Option
Description
Choose whether the camera automatically detects and sets focus and expoFACE DETECTION
sure for human portrait subjects (P 66).
Add portrait subjects to the face recognition database. These subjects will be
FACE RECOGNITION given priority during Intelligent Face Detection, and their names and other
information can be viewed during playback (P 67).
C PHOTOMETRY
Choose how the camera meters exposure when Intelligent Face Detection is off.
Option
o MULTI
p SPOT
q AVERAGE
(default: o)
Description
Automatic scene recognition is used to adjust exposure for a wide range of
shooting conditions.
The camera meters lighting conditions at the center of the frame. Recommended when the background is much brighter or darker than the main
subject.
Exposure is set to the average for the entire frame. Provides consistent exposure across multiple shots with the same lighting, and is particularly effective
for landscapes and portraits of subjects dressed in black or white.
F FOCUS MODE
This option controls how the camera focuses subjects (P 62).
Menus
107
Using the Menus: Shooting Mode
F FOCUS AREA
This option controls how the camera selects the focus area for photographs (P 65). Regardless of
the option selected, the camera will focus on the subject in the center of the frame when macro
mode is on.
F Fn BUTTON
Choose the role played by the Fn button (P 54).
(default: N)
E E-Fn BUTTON CUSTOM SETTING
Choose the role played by the a button, the t button and the selector up, down, left and
right (P 55).
108
Menus
Using the Menus: Shooting Mode
v DISP. CUSTOM SETTING
Choose the items displayed in the LCD monitor. The following items can be displayed:
FRAMING GUIDLINE*
WHITE BALANCE
HISTOGRAM
IMAGE SIZE/QUALITY
PHOTOMETRY
FILM SIMULATION
EXP. COMPENSATION
ELECTRONIC LEVEL
APERTURE/S-SPEED/ISO
FRAMES REMAINING
BATTERY LEVEL
FLASH
DYNAMIC RANGE
* You can also select the grid type (P 125).
See pages 6 – 7 for the locations of these items in the displays.
Virtual Horizon
Selecting ELECTRONIC LEVEL displays a virtual horizon. The camera is
level when the two lines overlap.
P
R The virtual horizon may not be displayed if the camera lens is pointed up or down.
(default: ±0)
I FLASH
Adjust flash brightness. Choose from values between +2/3 EV and –2/3 EV. The default setting is
±0. Note that the desired results may not be achieved depending on shooting conditions and
the distance to the subject.
Menus
109
Using the Menus: Shooting Mode
W MOVIE SET-UP
Adjust movie settings.
Option
MOVIE MODE
MOVIE AF MODE
Description
Choose a frame size for movies (P 83).
This option controls how the camera selects the focus area for movies.
• r CENTER: When shooting starts, the camera focuses on the subject in the
center of the frame.
• u CONTINUOUS: The camera continuously adjusts focus to reflect changes in
the distance to subjects near the center of the frame.
R Note that in u mode, the camera focuses continuously, increasing the
drain on the battery, and that the sound of the camera focusing may be
audible.
R If a face is detected when u is selected, a o icon will be displayed and
the camera will continuously adjust focus to maintain focus on the face.
Choose how the camera records photographs taken during movie recording.
• MOVIE PRIORITY
PRIORITY: The camera takes a photograph without interrupting movie recording. Image size is determined by the option selected for MOVIE
STILL SHOOTING IN MODE.
MOVIE
• STILL IMAGE PRIORITY
PRIORITY: The camera interrupts filming to take the photograph
and resumes filming automatically when recording is complete. Image size
is determined by the option selected for O IMAGE SIZE, but note that the
photograph will be recorded at size P if O is selected.
K CUSTOM SET
Save settings for P, S, A, M and all EXR modes except R (P 46).
110
Menus
Using the Menus: Playback Mode
Using the Playback Menu
1 Display the playback menu.
1.1 Press MENU/OK during playback to display the
playback menu.
1.2 Press the selector left to highlight the current tab.
Tab
PLAYBACK MENU
1.3 Press the selector up or down to highlight the tab
containing the desired option.
EXIT
1.4 Press the selector right to place the cursor in the menu.
2 Adjust settings.
Highlight items and press the selector right to view options, then highlight an option and press MENU/OK. Press DISP/BACK to exit when settings
are complete.
Menus
111
Using the Menus: Playback Mode
Playback Menu Options
m PHOTOBOOK ASSIST
Create books from your favorite photos (P 76).
b IMAGE SEARCH
Search for pictures (P 75).
A ERASE
Delete all or selected pictures (P 74).
112
Menus
Using the Menus: Playback Mode
j MARK FOR UPLOAD TO
Select pictures for upload to YouTube or Facebook using MyFinePix Studio (Windows only).
■ Selecting Pictures for Upload
1 Select YouTube to choose movies for upload to YouTube, FACEBOOK to choose photos and
movies for upload to Facebook.
2 Press the selector left or right to display pictures and press MENU/OK to select or deselect. Press
DISP/BACK to exit when all the desired pictures are selected.
R Only movies can be selected for upload to YouTube.
R During playback, selected pictures are indicated by j YouTube or j FACEBOOK icons.
■ RESET ALL: Deselecting All Pictures
Choose RESET ALL to deselect all pictures. If the number of pictures affected is very large, a
message will be displayed while the operation is in progress. Press DISP/BACK to exit before the
operation is complete.
■ Uploading Pictures (Windows Only)
Selected pictures can be uploaded using the YouTube/Facebook Upload option in MyFinePix
Studio.
Select with camera
Upload from computer
For information on installing MyFinePix Studio and connecting the camera to a computer, see
“Viewing Pictures on a Computer” (P 91).
Menus
113
Using the Menus: Playback Mode
(default: MULTIPLE)
I SLIDE SHOW
View pictures in an automated slide show. Choose the type of show and press MENU/OK to start.
Press DISP/BACK at any time during the show to view on-screen help. The show can be ended at
any time by pressing MENU/OK.
Option
NORMAL
FADE-IN
NORMAL g
FADE-IN g
MULTIPLE
Description
Press selector left or right to go back or skip ahead one frame. Select FADE-IN
for fade transitions between frames.
As above, except that camera automatically zooms in on faces selected with
Intelligent Face detection.
Display several pictures at once.
R The camera will not turn off automatically while a slide show is in progress.
114
Menus
Using the Menus: Playback Mode
j RAW CONVERSION
Create JPEG copies of RAW pictures. The original image data are unaffected, allowing a single
RAW image to be processed in a multitude of different ways.
RAW CONVERSION
1 Select j RAW CONVERSION in the playback menu.
REFLECT SHOOTING COND.
PUSH/PULL PROCESSING
DYNAMIC RANGE
FILM SIMULATION
WHITE BALANCE
WB SHIFT
CREATE
CANCEL
2 Press the selector up or down to highlight a setting and press the selector right to select.
Press the selector up or down to highlight the desired option and press MENU/OK to select and
return to the settings list. Repeat this step to adjust additional settings.
3 Press the E-Fn button to preview the JPEG copy. Press MENU/OK to save
the copy or press DISP/BACK to return to Step 2.
STORE
Menus
CANCEL
115
Using the Menus: Playback Mode
j RAW CONVERSION (Continued)
Setting
Description
Create a JPEG copy using the settings in effect at the time the photo
REFLECT SHOOTING COND.
was taken.
PUSH/PULL PROCESSING Adjust exposure by –1 EV to +1 EV in increments of 1/3 EV (P 49).
DYNAMIC RANGE
Enhance details in highlights for natural contrast (P 102).
FILM SIMULATION
Simulate the effects of different types of film (P 103).
WHITE BALANCE
Adjust white balance (P 104).
WB SHIFT
Fine-tune white balance (P 106).
COLOR
Adjust color density (P 106).
SHARPNESS
Sharpen or soften outlines (P 106).
NOISE REDUCTION
Process the copy to reduce mottling (P 106).
HIGHLIGHT TONE
Adjust highlights (P 106).
SHADOW TONE
Adjust shadows (P 106).
116
Menus
Using the Menus: Playback Mode
B RED EYE REMOVAL
If the current picture is marked with a g icon to indicate that it was taken with Intelligent Face
Detection, this option can be used to remove red-eye. The camera will analyze the image; if redeye is detected, the image will be processed to create a copy with reduced red-eye.
1 Display the desired picture.
2 Select B RED EYE REMOVAL in the playback menu.
3 Press MENU/OK.
R Red eye may not be removed if the camera is unable to detect a face or the face is in profile.
Results may differ depending on the scene. Red eye can not be removed from pictures that
have already been processed using red-eye removal or pictures created with other devices.
R The amount of time needed to process the image varies with the number of faces detected.
R Copies created with B RED EYE REMOVAL are indicated by a e icon during playback.
D PROTECT
Protect pictures from accidental deletion.
1 Select D PROTECT in the playback menu.
2 Highlight one of the following options and press MENU/OK:
• FRAME: Protect selected pictures. Press the selector left or right to view pictures and press
MENU/OK to select or deselect. Press DISP/BACK when the operation is complete.
• SET ALL: Protect all pictures.
• RESET ALL: Remove protection from all pictures.
Q Protected pictures will be deleted when the memory card or internal memory is formatted
(P 131).
Menus
117
Using the Menus: Playback Mode
G CROP
Create a cropped copy of the current picture.
1 Display the desired picture.
2 Select G CROP in the playback menu.
3 Rotate the main-command dial to zoom in and out and use the selector to scroll the picture
until the desired portion is displayed.
4 Press MENU/OK to display a confirmation dialog.
5 Press MENU/OK again to save the cropped copy to a separate file.
R Larger crops produce larger copies; all copies have an aspect ratio of 4 : 3. If the size of the final
copy will be a, OK will be displayed in yellow.
O RESIZE
Create a small copy of the current picture.
1 Display the desired picture.
2 Select O RESIZE in the playback menu.
3 Highlight a size and press MENU/OK to display a confirmation dialog.
4 Press MENU/OK to save the resized copy to a separate file.
R The sizes available vary with the size of the original image.
118
Menus
Using the Menus: Playback Mode
C IMAGE ROTATE
Rotate pictures taken in tall orientation so that they are displayed in tall orientation in the LCD
monitor.
1 Display the desired picture.
2 Select C IMAGE ROTATE in the playback menu.
3 Press the selector down to rotate the picture 90 ° clockwise, up to rotate it 90 ° counterclockwise.
4 Press MENU/OK. The picture automatically be displayed in the selected orientation whenever it
is played back on the camera.
R Protected pictures can not be rotated. Remove protection before rotating pictures (P 117).
R The camera may not be able to rotate pictures created with other devices.
E COPY
Copy pictures from internal memory to a memory card.
1 Select E COPY in the playback menu.
2 Highlight one of the following options and press the selector right:
• a INTERNAL MEMORY y b CARD: Copy pictures from internal memory to a memory card.
• b CARD y a INTERNAL MEMORY: Copy pictures from a memory card to internal memory.
3 Highlight one of the following options and press MENU/OK:
• FRAME: Copy selected pictures. Press the selector left or right to view pictures and press
MENU/OK to copy the current picture.
• ALL FRAMES: Copy all pictures.
R Copying ends when the destination is full.
R DPOF print information is not copied (P 89).
Menus
119
Using the Menus: Playback Mode
F VOICE MEMO
Add a voice memo to the current photograph. Holding the camera at a distance of about 20 cm,
face the microphone and press MENU/OK to begin recording. Press MENU/OK again to end recording (recording ends automatically after 30 seconds).
R Voice memos can not be added to movies or protected pictures. Remove protection from
pictures before recording voice memos.
R If a voice memo already exists for the current picture, the options will be displayed. Select
RE-REC to replace the existing memo.
Playing Voice Memos
Pictures with voice memos are indicated by a q icon during playback. To play the voice
memo back, select PLAY for F VOICE MEMO.
R The camera may not play voice memos recorded with other devices.
R Do not cover the speaker during playback.
i ERASE FACE RECOG.
Remove face recognition links from the current image. When this option is selected, the camera will zoom in on an area in the current picture that it has matched with a face in the face
recognition database. If the match is not correct, press MENU/OK to remove the link to the face
recognition database.
R Face recognition links can not be removed from copies with a size of a or smaller.
120
Menus
Using the Menus: Playback Mode
K PRINT ORDER (DPOF)
Select pictures for printing on DPOF- and PictBridge-compatible devices (P 89).
J DISP ASPECT
Choose how High Definition (HD) devices display pictures with an aspect ratio of 4 : 3 (this option
is available only when an HDMI cable is connected). Select 16 : 9 to display the image so that it
fills the screen with its top and bottom cropped out, 4 : 3 to display the entire image with black
bands at either side.
16 : 9
4:3
16 : 9
4:3
R Photographs with an aspect ratio of 16 : 9 are displayed full screen, those with an aspect ratio
of 3 : 2 in a black frame.
Menus
121
The Setup Menu
Using the Setup Menu
1 Display the setup menu.
1.1 Press MENU/OK to display the menu for the current
mode.
SET-UP
1.2 Press the selector left to highlight the tab for the
current menu.
1.3 Press the selector down to highlight the tab containing the desired option.
EXIT
Tab
1.4 Press the selector right to place the cursor in the menu.
2 Adjust settings.
Highlight items and press the selector right to view options, then highlight an option and press MENU/OK. Press DISP/BACK to exit when settings
are complete.
122
Menus
The Setup Menu
Setup Menu Options
F DATE/TIME
Set the camera clock (P 24).
N TIME DIFFERENCE
(default: h)
Switch the camera clock instantly from your home time zone to the local time at your destination when traveling. To specify the difference between local time and your home time zone:
1 Highlight g LOCAL and press the selector right.
2 Use the selector to choose the time difference between local time and your home time zone.
3 Press MENU/OK.
To switch between local time and your home time zone, highlight g LOCAL or h HOME and
press MENU/OK.
Option
h HOME
g LOCAL
Description
Switch to the time currently selected for F DATE/TIME (see above).
Switch to local time. If this option is selected, g and the time and date will
be displayed in yellow for three seconds each time the camera is turned on.
Qa
Choose a language.
Menus
123
The Setup Menu
R RESET
Reset all settings except F DATE/TIME, N TIME DIFFERENCE, A SCREEN SET-UP > BACKGROUND COLOR, and Q VIDEO SYSTEM to default values.
1 Highlight R RESET and press the selector right to display a confirmation dialog.
2 Highlight OK and press MENU/OK.
(default: OFF)
o SILENT MODE
Select ON to disable the speaker, flash, and AF-assist illuminator in situations in which camera
sounds or lights may be unwelcome (note that the flash will still fire in C mode).
b SOUND SET-UP
Adjust sound settings.
Option
OPERATION VOL.
SHUTTER VOLUME
SHUTTER SOUND
PLAYBACK VOLUME
124
Description
Adjust the volume of the sounds produced when camera controls are operated. Choose e OFF (mute) to disable control sounds.
Adjust the volume of the sounds produced when the shutter is released.
Choose e OFF (mute) to disable the shutter sound.
Choose the sound made by the shutter.
Adjust the volume for movie and voice memo playback.
Menus
The Setup Menu
A SCREEN SET-UP
Adjust display settings.
Option
IMAGE DISP.
LCD BRIGHTNESS
MONITOR SUNLIGHT
MODE
FRAMING GUIDLINE
AUTOROTATE PB
BACKGROUND COLOR
GUIDANCE DISPLAY
FOCUS CHECK
Menus
Description
Choose how long pictures are displayed in the LCD monitor after shooting.
• 3 SEC, 1.5 SEC: Pictures are displayed for three seconds (3 SEC) or 1.5 seconds (1.5 SEC). Colors may differ slightly from those in the final image.
• ZOOM (CONTINUOUS): Pictures are displayed until the MENU/OK button is
pressed.
• OFF: Pictures are not displayed after shooting.
Control the brightness of the display.
Select ON to make the display in the monitor easier to read in bright light.
Choose the type of framing grid available in shooting mode.
• F GRID 9: For “rule of thirds” composition.
• G GRID 24: A six-by-four grid.
• H HD FRAMING: Frame HD pictures in the crop shown by the lines at the
top and bottom of the display.
Choose ON to automatically rotate “tall” (portrait-orientation) pictures during playback.
Choose a color scheme.
Choose whether to display tool tips.
If ON is selected for j FOCUS CHECK, the image will be magnified in the
display to assist focus when the sub-command dial is rotated in manual
focus mode (P 62). The camera must be in manual focus mode.
125
The Setup Menu
Z POWER MANAGEMENT
Adjust power management settings.
Option
AUTO POWER OFF
QUICK START MODE
POWER
MANAGEMENT
Description
Choose the length of time before the camera turns off automatically when
no operations are performed. Shorter times increase battery life; if OFF is
selected, the camera must be turned off manually. Note that in some situations the camera turns off automatically even when OFF is selected.
Allow the camera to restart in a fast manner after turned off (ON/OFF).
Q This option will increase drain on the battery.
Optimize camera performance for increased battery life or display quality.
• n POWER SAVE: The display dims to save power if no operations are performed for a short period, but can be restored by operating camera controls. Select this option to save power.
• o CLEAR DISPLAY: Choose this option for a brighter, higher quality display
and for a longer delay before the monitor dims to save power.
R n POWER SAVE does not take effect when Intelligent Face Detection
is on.
126
Menus
The Setup Menu
L IS MODE
Choose from the following image stabilization options:
(default: L)
Option
Description
L CONTINUOUS + MOTION Image stabilization on. If + MOTION is selected, the camera will
adjust shutter speed to reduce motion blur when a moving objects
l CONTINUOUS
are detected.
M SHOOTING + MOTION As above, except that image stabilization is performed only when
the shutter button is pressed halfway or the shutter is released.
m SHOOTING ONLY
OFF
Image stabilization off. Choose this option when using a tripod.
R + MOTION has no effect when sensitivity is set to a fixed value, and may also be unavailable
at some other combinations of settings. The effect may vary with lighting conditions and the
speed at which the object is moving.
(default: ON)
B RED EYE REMOVAL
Choose ON to remove red-eye effects caused by the flash when shooting with Intelligent Face
Detection.
R Red-eye reduction is performed only when a face is detected.
R Red-eye removal is not available with RAW images.
Menus
127
The Setup Menu
(default: ON)
C AF ILLUMINATOR
If ON is selected, the AF-assist illuminator will light to assist autofocus.
Q The camera may be unable to focus using the AF-assist illuminator in some cases. If the camera is unable to focus in macro mode, try increasing the distance to the subject.
Q Avoid shining the AF-assist illuminator directly into your subject’s eyes.
(default: OFF)
j RAW
Choose RAW+JPEG or RAW to record RAW pictures (note that RAW pictures are unprocessed
data read from the image sensor). If RAW+JPEG is selected, JPEG copies will also be recorded.
Choose OFF to record pictures in JPEG format only.
R To convert RAW files for display on the camera, use j RAW CONVERSION in the playback
menu (P 115).
R To convert RAW files for display on a computer, use the supplied RAW File Converter software.
Q Crop, resize, and red-eye removal are not available with RAW images. The maximum zoom
available when viewing RAW images is 3.2 ×.
128
Menus
The Setup Menu
t SAVE DATA SET-UP
Adjust file-management settings.
Option
FRAME NO.
SAVE ORG IMAGE
Menus
Description
New pictures are stored in image files named using
Frame number
a four-digit file number assigned by adding one to
100-0001
the last file number used. The file number is displayed during playback as shown at right. FRAME Directory
File
NO. controls whether file numbering is reset to 0001 number
number
when a new memory card is inserted or the current
memory card or internal memory is formatted.
• CONTINUOUS: Numbering continues from the last file number used or the
first available file number, whichever is higher. Choose this option to reduce the number of pictures with duplicate file names.
• RENEW: Numbering is reset to 0001 after formatting or when a new memory
card is inserted.
R If the frame number reaches 999-9999, the shutter release will be disabled
(P 144).
R Selecting R RESET (P 124) sets FRAME NO. to CONTINUOUS but does
not reset the file number.
R Frame numbers for pictures taken with other cameras may differ.
Choose ON to save unprocessed copies of seamless z panoramas or pictures taken using B RED EYE REMOVAL, j PRO LOW-LIGHT MODE, or
i PRO FOCUS MODE.
129
The Setup Menu
t SAVE DATA SET-UP (Continued)
Option
Description
Stamp the time and/or date of recording on photographs as they are taken.
• R+S: Stamp new photographs with the date and time of recording.
• R: Stamp new photographs with the date of recording.
• OFF: Do not stamp the time and date on new photographs.
DATE STAMP
Q Time and date stamps can not be deleted. Turn DATE STAMP off to prevent time and date stamps appearing on new photographs.
Q If the camera clock is not set, you will be prompted to set the clock to the
current date and time (P 24).
Q We recommend that you turn the DPOF “print date” option off when
printing images with a time and date stamp (P 89).
Q Time and date stamps do not appear on movies, panoramas, or 3D photos.
I FOCUS CONTROL DIAL
(default: X CW)
Choose the direction in which the sub-command dial is rotated to increase the focus distance.
Q VIDEO SYSTEM
Choose a video mode for connection to a TV.
Option
NTSC
PAL
130
Description
Select this mode for connection to video devices in North America, the Caribbean, parts of Latin America, and some East Asian countries.
Select this mode for connection to video devices in the United Kingdom and
much of Europe, Australia, New Zealand, and parts of Asia and Africa.
Menus
The Setup Menu
S CUSTOM RESET
Reset all settings for mode C1/C2. A confirmation dialog will be displayed, press the selector up
or down to highlight OK and press MENU/OK.
K FORMAT
If a memory card is inserted in the camera, this option will format the memory card. If no memory card is inserted, this option will format internal memory.
Q All data—including protected pictures—will be deleted from the memory card or internal
memory. Be sure important files have been copied to a computer or other storage device.
Q Do not open the battery-chamber cover during formatting.
Menus
131
Technical Notes
Optional Accessories
The camera supports a wide range of accessories from FUJIFILM and other
manufacturers.
■ Printing
DIGITAL CAMERA
XF1
USB cable
(supplied)
PictBridge-compatible
printer *
■ Digital viewer
Supports 3D display of
pictures taken using INDIVD.
SHUTTER 3D.
FINEPIX REAL 3D V3 (sold separately)
SD/SDHC/SDXC
memory card
■ Audio/Visual
A/V cable (sold separately)
Printer *
■ Computer Related
TV *
HDMI cable (sold separately)
HDTV *
USB cable (supplied)
SD card slot or card reader
Computer *
* Available separately.
132
■ 3D print
Photos taken in INDIVD. SHUTTER 3D.
http://fujifilm.com/3d/print/
Optional Accessories
Accessories from FUJIFILM
The following optional accessories are available from FUJIFILM. For the latest information on the accessories available in your region, check with your
local FUJIFILM representative or visit http://www.fujifilm.com/products/digital_
cameras/index.html.
NP-50: Additional large-capacity NP-50 rechargeable batRechargeable
teries can be purchased as required. Note that the NP-50
Li-ion batteries
may record fewer photos per charge than the NP-50A.
Battery
chargers
BC-45W: Replacement battery chargers can be purchased
as required. The BC-45W charges an NP-50A/NP-50 battery in about 150 minutes at +20 °C (+68 °F).
AC power
adapters
AC-5VX (requires CP-50 DC coupler): Use for extended playback or
when copying pictures to a computer (shape of adapter
and plug vary with region of sale).
DC couplers
CP-50: Connect the AC-5VX to the camera.
A/V cable
AV-C1: Use for viewing pictures on TV.
Digital viewer FINEPIX REAL 3D V3:
V3 View 3D images without 3D glasses.
Camera case
SC-XF: The camera case and the strap are exclusively for
SC-XF:
use with the XF1.
Technical Notes
133
Caring for the Camera
To ensure continued enjoyment of the product, observe the following precautions.
Storage and Use
If the camera will not be used for an
extended period, remove the battery
and memory card. Do not store or
use the camera in locations that are:
• exposed to rain, steam, or smoke
• very humid or extremely dusty
• exposed to direct sunlight or very
high temperatures, such as in a
closed vehicle on a sunny day
• extremely cold
• subject to strong vibration
• exposed to strong magnetic fields,
such as near a broadcasting antenna, power line, radar emitter, motor,
transformer, or magnet
• in contact with volatile chemicals
such as pesticides
• next to rubber or vinyl products
134
■ Water and Sand
Exposure to water and sand can also
damage the camera and its internal
circuitry and mechanisms. When
using the camera at the beach or
seaside, avoid exposing the camera
to water or sand. Do not place the
camera on a wet surface.
■ Condensation
Sudden increases in temperature,
such as occur when entering a heated
building on a cold day, can cause condensation inside the camera. If this
occurs, turn the camera off and wait
an hour before turning it on again. If
condensation forms on the memory
card, remove the card and wait for the
condensation to dissipate.
Technical Notes
Caring for the Camera
Cleaning
Use a blower to remove dust from the lens and LCD monitor, then gently wipe
with a soft, dry cloth. Any remaining stains can be removed by wiping gently
with a piece of FUJIFILM lens-cleaning paper to which a small amount of lenscleaning fluid has been applied. Care should be taken to avoid scratching the
lens or LCD monitor. The camera body can be cleaned with a soft, dry cloth.
Do not use alcohol, thinner, or other volatile chemicals.
Traveling
Keep the camera in your carry-on baggage. Checked baggage may suffer
violent shocks that could damage the camera.
Technical Notes
135
Troubleshooting
Problems and Solutions
■ Power and Battery
Problem
Solution
• The zoom ring (ON/OFF switch) is not correctly rotated:
rotated: Rotate the zoom ring to STANDBY
and then rotate the zoom ring again to the point between 25 and 100 ((P
P 20).
• The battery is exhausted
exhausted:: Charge the battery or insert a fully-charged spare battery ((P
P 13).
The camera does not
• The battery is inserted incorrectly:
incorrectly: Reinsert in the correct orientation (P
(P 15).
turn on.
• The battery-chamber cover is not latched
latched:: Latch the battery-chamber cover (P
(P 15).
• The AC power adapter and DC coupler are connected incorrectly:
incorrectly: Reconnect the AC power
adapter and DC coupler.
• The battery is cold
cold:: Warm the battery by placing it in a pocket or other warm place and reinsert
it in the camera immediately before taking a picture.
• There is dirt on the battery terminals
terminals:: Clean the terminals with a soft, dry cloth.
• o CLEAR DISPLAY is selected for Z POWER MANAGEMENT
MANAGEMENT >
> POWER
MANAGEMENT:: Select n POWER SAVE to reduce the drain on the battery ((P
MANAGEMENT
P 126).
The battery runs down • ON is selected for A SCREEN SET-UP >
SET-UP > MONITOR SUNLIGHT MODE:
MODE: Select
quickly.
OFF to reduce the drain on the battery (P
(P 8).
• R is selected for shooting mode:
mode: Select B mode to reduce the drain on the battery ((P
P 30).
• u CONTINUOUS or x TRACKING is selected for F FOCUS MODE
MODE:: Select a
different AF mode (P
(P 62).
• The battery has been charged many times
times:: The battery has reached the end of its charging
life. Purchase a new battery.
• The battery is exhausted
exhausted:: Charge the battery or insert a fully-charged spare battery ((P
P 13).
The camera turns off
• The AC power adapter or DC coupler has been disconnected:
disconnected: Reconnect the AC power
suddenly.
adapter and DC coupler.
Charging does not start. Reinsert the battery in the correct orientation and make sure that the charger is plugged in ((P
P 13).
136
Problems and Solutions
Problem
Charging is slow.
Solution
Charge the battery at room temperature (P
(P vi).
• There is dirt on the battery terminals
terminals:: Clean the terminals with a soft, dry cloth.
The charging lamp lights,
• The battery has been charged many times
times:: The battery has reached the end of its charging
but the battery does not
life. Purchase a new battery. If the battery still fails to charge, contact your FUJIFILM dealer.
charge.
• The battery is too hot or too cold
cold:: Wait for the battery temperature to stabilize (P
(P 13).
■ Menus and Displays
Problem
Menus and displays are
not in English.
Solution
Select ENGLISH for Q a ((P
P 24, 123).
■ Shooting
Problem
•
•
•
No picture is taken when
•
the shutter button is
•
pressed.
•
•
Solution
Memory is full:
full: Insert a new memory card or delete pictures ((P
P 16, 74).
Memory is not formatted:
formatted: Format the memory card or internal memory ((P
P 131).
There is dirt on the memory card contacts
contacts:: Clean the contacts with a soft, dry cloth.
The memory card is damaged
damaged:: Insert a new memory card (P
(P 16).
The battery is exhausted
exhausted:: Charge the battery or insert a fully-charged spare battery ((P
P 13).
The camera has turned off automatically:
automatically: Turn the camera on ((P
P 23).
The indicator lamp was orange when you attempted to record a panorama
panorama:: Wait until
the indicator lamps turns off (P
(P 5).
The LCD monitor goes
The LCD monitor may darken while the flash charges. Wait for the flash to charge ((P
P 51).
dark after shooting.
3D images do not turn out
Use a tripod or change the distance the camera is moved between the first and second shots ((P
P 39).
as expected.
Troubleshooting
137
Problems and Solutions
Problem
The camera does not
focus.
Pictures are not the
same size.
Solution
• The subject is close to the camera
camera:: Select macro mode (P
(P 50).
• The subject is far away from the camera
camera:: Cancel macro mode (P
(P 50).
• The subject is not suited to autofocus
autofocus:: Use focus lock ((P
P 47).
If S is selected for O IMAGE SIZE in R mode, the camera will optimize not only sensitivity and other settings, but also image size. To record all pictures at the same size, choose another
shooting mode or select another option for O IMAGE SIZE ((P
P 101).
Macro mode is not
Choose a different shooting mode ((P
P 30).
available.
Intelligent Face Detection Intelligent Face Detection is not available in the current shooting mode:
mode: Choose a differis not available.
ent shooting mode (P
(P 30).
• The subject’s face is obscured by sunglasses, a hat, long hair, or other objects:
objects: Remove
the obstructions.
• The subject’s face occupies only a small area of the frame
frame:: Change the composition so that
No face is detected.
the subject’s face occupies a larger area of the frame ((P
P 47).
• The subject’s head is tilted or horizontal
horizontal:: Ask the subject to hold their head straight.
• The camera is tilted
tilted:: Keep the camera level (P
(P 26).
• The subject’s face is poorly lit
lit:: Shoot in bright light.
Wrong subject is
The selected subject is closer to the center of the frame than the main subject. Recompose the
selected.
picture or turn face detection off and frame the picture using focus lock (P
(P 47).
• The flash is not available in the current shooting mode
mode:: Choose a different shooting mode
(P 30).
• The battery is exhausted
exhausted:: Charge the battery or insert a fully-charged spare battery ((P
P 13).
The flash does not fire.
• The camera is in continuous mode
mode:: Select B for R CONTINUOUS ((P
P 57).
• The camera is in silent mode
mode:: Turn silent mode off (P
(P 124).
• The flash is not raised
raised:: Raise the flash (P
(P 51).
• The desired flash mode is not available in the current shooting mode
mode:: Choose a different
Some flash modes are
shooting mode (P
(P 30).
not available.
• The camera is in silent mode
mode:: Turn silent mode off (P
(P 124).
138
Troubleshooting
Problems and Solutions
Problem
Solution
The subject is not in range of the flash
ash:: Position the subject in range of the flash (P
(P 149).
The flash does not fully
The flash window is obstructed
obstructed:: Hold the camera correctly ((P
P 26).
light the subject.
Fast shutter speed selected:
selected: Choose a slower shutter speed ((P
P 42, 44).
The lens is dirty
dirty:: Clean the lens ((P
P 135).
The lens is blocked
blocked:: Keep objects away from the lens (P
(P 26).
Pictures are blurred.
s is displayed during shooting and the focus frame is displayed in red:
red: Check focus
before shooting ((P
P 142).
• k is displayed during shooting:
shooting: Use the flash or a tripod (P
(P 52).
• A slow shutter speed is selected at high temperatures:
temperatures: This is normal and does not indicated a malfunction.
Pictures are mottled.
• The camera has been used continuously at high temperatures or a temperature warning is displayed:
displayed: Turn the camera off and wait for it to cool down.
Power was interrupted during shooting. Before connecting the AC power adapter or DC coupler,
Pictures are not recorded. turn the camera off. Leaving the camera on can result in corrupted files or damage to the memory
card or internal memory.
• u CONTINUOUS is selected for W MOVIE SET-UP > MOVIE AF MODE
MODE::
Sounds made by the
Select a different AF mode (P
(P 110).
camera are recorded with
• Zoom was adjusted during shooting
shooting:: Do not adjust zoom during shooting.
movies.
• Intelligent Face Detection is on:
on: Turn Intelligent Face Detection off (P
(P 66).
•
•
•
•
•
•
■ Playback
Problem
Pictures are grainy.
Playback zoom
unavailable.
Troubleshooting
Solution
The pictures were taken with a different make or model of camera.
The picture has been saved at a, or is from another make or model of camera ((P
P 72).
139
Problems and Solutions
Problem
Solution
• Playback volume is too low:
low: Adjust playback volume (P
(P 124).
No sound in movie
• The microphone was obstructed
obstructed:: Hold the camera correctly during recording ((P
P 2, 26).
playback.
• The speaker is obstructed
obstructed:: Hold the camera correctly during playback ((P
P 2, 26).
Selected pictures are not Some of the pictures selected for deletion are protected. Remove protection using the device with
deleted.
which it was originally applied (P
(P 117).
File numbering is
The battery-chamber cover was opened while the camera was on. Turn the camera off before
unexpectedly reset.
opening the battery-chamber cover.
■ Connections/Miscellaneous
Problem
No picture or sound.
Solution
• The camera is not properly connected
connected:: Connect the camera properly (P
(P 85).
• An A/V cable was connected during movie playback
playback:: Connect the camera once movie playback has ended.
• Input on the television is set to “TV”:
“TV”: Set input to “VIDEO”.
• The camera is not set to the correct video standard:
standard: Match the camera Q VIDEO SYSTEM setting to the TV (P
(P 130).
• The volume on the TV is too low:
low: Adjust the volume.
Match the camera Q VIDEO SYSTEM setting to the TV (P
(P 130).
No color.
The computer does not
Be sure the camera and computer are correctly connected ((P
P 96).
recognize the camera.
Can not transfer RAW or
Use the bundled software to transfer pictures (P
(P 91).
JPEG files to computer.
140
Troubleshooting
Problems and Solutions
Problem
Solution
Pictures can not be
• The camera is not properly connected
connected:: Connect the camera correctly (P
(P 87).
printed.
• The printer is off: Turn the printer on.
Only one copy is printed/
The printer is not PictBridge compatible.
the date is not printed.
• Temporary camera malfunction
malfunction:: Remove and reinsert the battery ((P
P 15) or disconnect and
The camera is
reconnect the AC power adapter/DC coupler.
unresponsive.
• The battery is exhausted
exhausted:: Charge the battery ((P
P 13) or insert a fully-charged spare battery
(P 15).
The camera does not
Remove and reinsert the battery (P
(P 15) or disconnect and reconnect the AC power adapter/DC
function as expected.
coupler. If the problem persists, contact your FUJIFILM dealer.
I want to use an AC power
Check the label on the AC power adapter. The AC power adapter can be used with voltages of
adapter and DC coupler
100 – 240 V. Consult your travel agent for information on plug adapters.
overseas.
No sound.
Turn silent mode off (P
(P 124).
Hue or content of display
Choose OFF for A SCREEN SET-UP >
SET-UP > MONITOR SUNLIGHT MODE ((P
P 8).
changes unexpectedly.
• Time and date stamps are not correct:
correct: Set the camera clock (P
(P 24).
• Time and date stamps appear on photographs:
photographs: Time and date stamps can not be deleted.
Time and date stamps
To prevent stamps appearing on new photographs, select OFF for t SAVE DATA SETUP >
UP
> DATE STAMP ((P
P 130).
FinePixViewer can not
FinePixViewer does not support Mac OS X version 10.7 or later. Use one of the applications supplied
be installed or does not
with Mac OS X or purchase other software.
start.
Troubleshooting
141
Warning Messages and Displays
The following warnings are displayed in the LCD monitor:
Warning
B ((red
red))
A ((blinks
blinks red)
red)
k
Description
Low battery. Charge the battery ((P
P 13) or insert a fully-charged spare battery ((P
P 15).
Battery exhausted. Charge the battery (P
(P 13) or insert a fully-charged spare battery (P
(P 15).
Slow shutter speed. Pictures may be blurred; use the flash or a tripod.
The camera can not focus. Try one of the following solutions:
s
• Use focus lock to focus on another subject at the same distance, then recompose the picture
(displayed in red with red
(P 47).
focus frame)
frame)
• Use macro mode to focus when taking close-ups (P
(P 50).
Aperture or shutter speed The subject is too bright or too dark and the picture will be over- or under-exposed. If the subject
displayed in red
is dark, use the flash (P
(P 51).
FOCUS ERROR
TURN OFF THE CAMERA Camera malfunction or moving parts of lens obstructed. Turn the camera off and then on again,
AND TURN ON AGAIN taking care not to touch the lens. If the message persists, contact a FUJIFILM dealer.
LENS CONTROL ERROR
• The memory card or internal memory is not formatted or the memory card was formatted in a computer or other device
device:: Format the memory card or internal memory using
the K FORMAT option in the camera setup menu (P
(P 131).
CARD NOT INITIALIZED
• The memory card contacts require cleaning
cleaning:: Clean the contacts with a soft, dry cloth. If
the message is repeated, format the card (P
(P 131). If the message persists, replace the card.
• Camera malfunction:
malfunction: Contact a FUJIFILM dealer.
PROTECTED CARD
The memory card is locked. Unlock the card ((P
P 16).
BUSY
The memory card is incorrectly formatted. Use the camera to format the card (P
(P 131).
Turn the camera off and wait for it to cool. If no action is taken, the camera will turn off autop
matically.
142
Troubleshooting
Warning Messages and Displays
Warning
CARD ERROR
MEMORY FULL
INTERNAL MEMORY IS
FULL
INSERT A NEW CARD
WRITE ERROR
READ ERROR
Troubleshooting
Description
The memory card is not formatted for use in the camera. Format the card (P
(P 131).
The memory card contacts require cleaning or the memory card is damaged. Clean the contacts
with a soft, dry cloth. If the message is repeated, format the card ((P
P 131). If the message persists, replace the card.
Incompatible memory card. Use a compatible card (P
(P 18).
Camera malfunction. Contact a FUJIFILM dealer.
The memory card or internal memory is full and pictures can not be recorded or copied. Delete
pictures or insert a memory card with more free space.
• Memory card error or connection error
error:: Reinsert the card or turn the camera off and then
on again. If the message persists, contact a FUJIFILM dealer.
• Not enough memory remaining to record additional pictures
pictures:: Delete pictures or insert
a memory card with more free space.
• The memory card or internal memory is not formatted:
formatted: Format the memory card or
internal memory (P
(P 131).
• The file is corrupt or was not created with the camera
camera:: The file can not be viewed.
• The memory card contacts require cleaning
cleaning:: Clean the contacts with a soft, dry cloth. If
the message is repeated, format the card (P
(P 131). If the message persists, replace the card.
• Camera malfunction:
malfunction: Contact a FUJIFILM dealer.
143
Warning Messages and Displays
Warning
FRAME NO. FULL
Description
The camera has run out of frame numbers (current frame number is 999-9999). Format the
memory card and select RENEW for t SAVE DATA SET-UP >
SET-UP > FRAME NO
NO.. Take
a picture to reset frame numbering to 100-0001, then select CONTINUOUS for FRAME
NO. ((P
P 129).
PRESS AND HOLD
An attempt was made to choose a flash mode or adjust the volume with the camera in silent
THE DISP BUTTON TO
mode. Exit silent mode before choosing a flash mode or adjusting the volume ((P
P 124).
DEACTIVATE SILENT MODE
• A search has returned more than 30,000 results
results:: Choose a search that returns fewer
TOO MANY FRAMES
results.
• More than 999 images are selected for deletion
deletion:: Choose fewer images.
An attempt was made to delete, rotate, or add a voice memo to a protected picture. Remove
PROTECTED FRAME
protection and try again (P
(P 117).
a pictures can not be cropped.
a CAN NOT CROP
CAN NOT CROP
The picture is damaged or was not created with the camera.
P CANNOT EXECUTE
An attempt was made to create a resized copy at a size equal to or larger than the original.
Q CANNOT EXECUTE
Choose a smaller size.
a CANNOT EXECUTE
CAN NOT ROTATE
An attempt was made to rotate a picture that can not be rotated.
F CAN NOT ROTATE Movies can not be rotated.
m CANNOT EXECUTE Red-eye removal can not be applied to the selected picture.
F CANNOT EXECUTE Red-eye removal can not be applied to movies.
NO CARD
No memory card inserted when E COPY is selected. Insert a memory card.
144
Troubleshooting
Warning Messages and Displays
Warning
NO IMAGE
Description
The source selected for E COPY contains no images. Select a different source.
• The voice memo file is corrupt
corrupt:: The voice memo can not be played back.
u ERROR
• Camera malfunction:
malfunction: Contact a FUJIFILM dealer.
The DPOF print order on the current memory card contains more than 999 images. Copy the
DPOF FILE ERROR
pictures to internal memory and create a new print order.
CAN NOT SET DPOF
The picture can not be printed using DPOF.
F CAN NOT SET DPOF Movies can not be printed using DPOF.
A connection error occurred while pictures were being printed or copied to a computer or other
COMMUNICATION ERROR
device. Confirm that the device is turned on and that the USB cable is connected.
Printer out of paper or ink, or other printer error. Check printer (see printer manual for details).
PRINTER ERROR
To resume printing, turn the printer off and then turn it back on.
PRINTER ERROR
Printer out of paper or ink, or other printer error. Check printer (see printer manual for details). If
RESUME?
printing does not resume automatically, press MENU/OK to resume.
An attempt was made to print a movie, a picture not created with the camera, or a picture in a
format not supported by the printer. Movies and some pictures created with other devices can
CANNOT BE PRINTED not be printed; if the picture is a still picture created with the camera, check the printer manual
to confirm that the printer supports the JFIF-JPEG or Exif-JPEG format. If it does not, the pictures
can not be printed.
Troubleshooting
145
Appendix
Memory Card Capacity
The following table shows the recording time or number of pictures available
at different image sizes. All figures are approximate; file size varies with the
scene recorded, producing wide variations in the number of files that can be
stored, and the number of exposures or length remaining may not diminish
at an even rate. A limited number of test pictures can be taken when no
memory card is inserted.
Medium
O
4 GB
T
Photographs
Movies
O 4:3
O 16 : 9
P 4:3
P 16 : 9
Q 4:3
Q 16 : 9
i 1920 × 1080 1
h 1280 × 720 1
f 640 × 480 2
k 640 × 480 3
k 320 × 240 3
k 320 × 112 3
FINE
800
1,060
1,280
1,690
2,360
3,440
8 GB
NORMAL
1,260
1,670
2,460
3,260
4,460
5,020
37 min.
47 min.
112 min.
83 min.
167 min.
83 min.
FINE
1,590
2,120
2,550
3,370
4,700
6,850
NORMAL
2,520
3,320
4,890
6,470
8,870
9,980
74 min.
95 min.
223 min.
166 min.
332 min.
166 min.
1 Use a G card or better. Individual movies can not exceed 29 minutes in length.
2 Individual movies can not exceed 120 minutes in length.
3 Use a G card or better. Individual movies can not exceed 30 seconds in length.
146
Specifications
System
Model
Effective pixels
Image sensor
Storage media
File system
File format
Image size (pixels)
Lens
Focal length
Digital zoom
Aperture
Appendix
XF1
12 million
2/3 -in., EXR CMOS with primary color filter
• Internal memory (approx. 25 MB) • SD/SDHC/SDXC memory cards
Compliant with Design Rule for Camera File System (DCF)
(DCF),, Exif 2.3, and Digital Print Order
Format (DPOF)
• Still pictures:
pictures: Exif 2.3 JPEG (compressed)
(compressed);; RAW (original RAF format, special-purpose software
required);; RAW+JPG available
required)
• Still pictures (3D)
(3D):: MPO
• Movies
Movies:: MOV (H.264)
• Audio
Audio:: WAV (stereo)
• O 4 : 3:3: 4,000 × 3,000 • O 3 : 22:: 4,000 × 2,664 • O 16 : 99:: 4,000 × 2,248 • O 1 : 1:1: 2,992 × 2,992
• P 4 : 3:3: 2,816 × 2,112 • P 3 : 22:: 2,816 × 1,864 • P 16 : 99:: 2,816 × 1,584 • P 1 : 1:1: 2,112 × 2,112
• Q 4 : 3:3: 2,048 × 1,536 • Q 3 : 22:: 2,048 × 1,360 • Q 16 : 99:: 1,920 × 1,080 • Q 1 : 1:1: 1,536 × 1,536
• r MOTION PANORAMA v: 1,624 × 11,520 (tall)
(tall)/11,520
/11,520 × 1,080 (wide)
• r MOTION PANORAMA w: 1,624 × 5,760 (tall)
(tall)/5,760
/5,760 × 1,080 (wide)
• r MOTION PANORAMA x: 1,624 × 3,840 (tall)
(tall)/3,840
/3,840 × 1,080 (wide)
• r MOTION PANORAMA z: 1,624 × 11,520 (tall)
(tall)/11,520
/11,520 × 1,080 (wide)
Fujinon 4 × optical zoom lens, F1.8 (wide angle) – F4.9 (telephoto)
f=6.4 mm–25.6 mm (35-mm format equivalent: 25 mm–100 mm)
Up to about 2 × with intelligent digital zoom (up to 8 × when combined with optical zoom)
F1.8–F11 (wide angle)/F4.9–F11
angle)/F4.9–F11 (telephoto) in increments of 1/3 EV
147
Specifications
System
Focus range
(distance from front of lens)
Sensitivity
Approx. 50 cm (1.6 ft.)–infinity (wide angle);
angle); 80 cm (2.6 ft.)–infinity (telephoto)
• Macro
Macro:: approx. 3 cm–3.0 m/1.1 in.–9.8 ft. (wide angle);
angle); 50 cm–3.0 m/1.6 ft.–9.8 ft. (telephoto)
Standard output sensitivity equivalent to ISO 100, 200, 250, 320, 400, 500, 640, 800, 1000, 1250,
1600, 2000, 2500, 3200, 40001, 50001, 64001, 128002; AUTO
AUTO,, AUTO (400)
(400),, AUTO (800),
(800), AUTO
(1600),, AUTO (3200)
(1600)
1 image size P or Q 2 image size Q
Metering
256-segment throughhrough-tthehe-llens (TTL) metering; MULTI, SPOT, AVERAGE
Exposure control
Programmed AE; aperture-priority AE; shutter-priority AE; manual exposure
Exposure compensation –2 EV – +2 EV in increments of 1/3 EV
Picture stabilization
Optical stabilization (lens-shift type)
Shutter speed (combined • O: 1/4 s–1/1,000 s • H: 3 s–1/1,000 s • U: 4 s–1/2 s
mechanical and electronic
• E, B, Adv.
Adv.,, SP (except O, H, and U): 1/4 s–1/2,000 s
shutter)
• P: 4 s–1/2,000 s
• Other modes:
modes: 30 s–1/2,000 s
Continuous
• I: max. 200 frames; frame rate can be selected from 10, 7, 5, and 3 fps (The
(The frame rate varies
depending on the shooting conditions or numbers of frames in continuous shooting.)
shooting.)
• P: 16 or 8 frames (RAW+JPEG/RAW:
(RAW+JPEG/RAW: max. 8 frames);
frames); frame rate can be selected from 10, 7, 5,
and 3 fps
• O: 3 frames (selected
(selected exposure, overexposure, underexposure)
underexposure)
• W: 3 frames (selected
(selected sensitivity, sensitivity raised, sensitivity lowered)
lowered)
• X: 3 frames (PROVIA,
(PROVIA, Velvia, ASTIA
ASTIA))
• Y: 3 frames (100%,
(100%, 200%
200%,, 400%
400%))
Focus
• Mode
Mode:: Single AF, continuous AF, manual focus
• Focus-area selection
selection:: Multi, area, tracking
• Autofocus system:
system: Contrast-detect TTL AF
White balance
Automatic scene detection; 8 manual preset modes for direct sunlight, shade, daylight fluorescent, warm white fluorescent, cool white fluorescent, incandescent lighting, underwater, color
temperature ; custom white balance
Self-timer
Off, 2 sec., 10 sec.
148
Appendix
Specifications
System
Flash
Flash mode
LCD monitor
Movies
Manual pop-up flash; effective range when sensitivity is set to 800 is approx. 50 cm–7.4 m/1.6 ft.–
24.2 ft. (wide angle; note that lens may block flash at short ranges)
ranges),, 80 cm–2.7 m/2.6 ft.–8.8 ft. (telephoto)
Auto, fill flash, off, slow sync (red-eye removal off ));; auto with red-eye removal, fill flash with redeye removal, off, slow sync with red-eye removal (red-eye removal on)
3.0-in., 460k-dot color LCD monitor; frame coverage approx. 100%
• i 1920
1920×
×1080
1080:: 1080p, 30 fps • h 1280
1280×
×720
720:: 720p, 30 fps
• f 640
640×
×480
480:: VGA, 30 fps
• k 640
640×
×480
480:: 70 fps
• k 320
320×
×240
240:: 120 fps
• k 320
320×
×112
112:: 200 fps
Note:: i, h, and f movies are recorded with stereo sound.
Note
Input/output terminals
A/V OUT (audio/video output) NTSC or PAL output with monaural sound
Digital input/output
USB 2.0 High-Speed; shares A/V OUT connector; MTP/PTP
HDMI output
HDMI mini connector
Appendix
149
Specifications
Power supply/other
Power supply
• NP-50A rechargeable battery
• AC-5VX AC power adapter and CP-50 DC coupler (sold separately)
Battery life (approximate
Battery type
Approximate number of frames
number of frames that can
NP-50A (type supplied with camera)
300
be taken with a fully-charged
CIPA standard, measured in B (auto) mode using battery supplied with camera and SD memory card.
battery)
Note: Number of shots that can be taken with battery varies with battery charge level and will
Note:
decline at low temperatures.
Dimensions (W × H × D) 107.9 mm × 61.5 mm × 33.0 mm/4.2 in. × 2.4 in. × 1.2 in., excluding projections
(minimum depth 24.1 mm/0.9 in.)
Shooting weight
Approx. 225 g/7.9 oz., including battery and memory card
Camera weight
Approx. 204 g/7.1 oz., excluding battery, accessories, and memory card
Operating conditions
• Temperature
Temperature:: 0 °C – +40 °C/+32 °F – +104 °F
• Humidity
Humidity:: 10–80% (no condensation)
150
Appendix
Specifications
NP-50A rechargeable battery
Nominal voltage
DC 3.7 V
Nominal capacity
1000 mAh
Operating temperature 0 °C – +40 °C/+32 °F – +104 °F
Dimensions (W × H × D) 35.4 mm × 40.0 mm × 6.6 mm/1.3 in. × 1.5 in. × 0.2 in.
Weight
Approx. 20 g/0.7 oz.
BC-50B battery charger
Rated input
Input capacity
Rated output
Supported batteries
Charging time
Operating temperature
Dimensions (W × H × D)
Weight
100 V–240 V AC, 50/60 Hz
• 100 V:
V: 8.0 VA
• 240 V:
V: 12 VA
4.2 V DC, 600 mA
NP-50A rechargeable batteries
Approx. 110 minutes (+20 °C/+68 °F)
0 °C – +40 °C/+32 °F – +104 °F
90 mm × 46 mm × 28 mm/3.5 in. × 1.8 in. × 1.1 in., excluding projections
Approx. 63 g/2.2 oz., excluding battery
Weight and dimensions vary with the country or region of sale.
Appendix
151
Specifications
■ Notices
• Specifications subject to change without notice; for the latest information, visit http://
www.fujifilm.com/products/digital_cameras/index.html. FUJIFILM shall not be held liable for damages resulting from errors in this manual.
• Although the LCD monitor is manufactured using advanced high-precision technology, small bright points and anomalous colors may appear, particularly in the vicinity
of text. This is normal for this type of LCD monitor and does not indicate a malfunction; images recorded with the camera are unaffected.
• Digital cameras may malfunction when exposed to strong radio interference (e.g.,
electric fields, static electricity, or line noise).
• Due to the type of lens used, some distortion may occur at the periphery of images.
This is normal.
152
Appendix
Memo
153
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN
http://www.fujifilm.com/products/digital_cameras/index.html
Restrictions on Camera Settings
The options available in each shooting mode are listed below.
Shooting Mode
E
Adv.
R S T U B Arij j i M A
Option
N BOFF
BON
Q
N
O
K
L
M
P
h
S/R
F
F
OFF
d
AUTO
N
AUTO (3200)
AUTO (1600)
AUTO (800)
AUTO (400)
12800 2
6400 3
5000
4000
3200
2500
2000
1600
1250
1000
800
640
500
400
320
250
200
100
✔ ✔ ✔
✔ ✔ ✔
✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔1
✔
✔
✔ ✔
✔ ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔
✔ ✔
✔
✔ ✔
✔ ✔
✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔
✔1
✔
✔
✔
✔
✔1 ✔1
✔
✔ ✔
✔ ✔
✔ ✔
✔1 ✔1
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔
✔
✔
✔
S
SP
P CD h Z M N O H p QRsf U V W F
✔
✔ ✔ ✔ ✔
✔
✔
✔
✔ ✔ ✔ ✔
✔
✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔
✔
✔1 ✔
✔ ✔ ✔
✔ ✔
✔ ✔ ✔1
✔ ✔ ✔
✔1 ✔1 ✔1
✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔1 ✔
✔ ✔ ✔
✔ ✔ ✔ ✔1
✔ ✔ ✔ ✔
✔
✔ ✔
✔ ✔
✔ ✔ ✔
✔1
✔ ✔
✔ ✔ ✔1 ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔
✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔ ✔1
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1
✔1 ✔
✔ ✔
✔1 ✔1
✔ ✔ ✔5
✔1 ✔1
Restrictions on Camera Settings
Shooting Mode
E
Adv.
R S T U B Arij j i M A
Option
O
S
O
P
Q
T
U
AUTO
V
W
X
Y
Z
c
d
e
b
e
d
f
f
P
D
R
O
W
X
Y
P
I P
J
K
O
B
Z
S
SP
P CD h Z M N O H p QRsf U V W F
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔1
✔ ✔1
✔1 ✔1 ✔
✔
✔
✔
✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔
✔ ✔ ✔ ✔ ✔
✔
✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔
✔
✔
✔ ✔
✔ ✔4 ✔ ✔
✔ ✔ ✔ ✔
✔1 ✔1 ✔1 ✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔1
✔1 ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔
✔ ✔
✔ ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔5
✔5
✔5
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔5
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔5
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔5
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔5
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔5
✔5
✔ ✔ ✔ ✔
✔
✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Restrictions on Camera Settings
Shooting Mode
E
Adv.
R S T U B Arij j i M A
Option
b
OFF
ON
o
p
q
M
t
s
u
x
C
F
n
W
W
L
B
C
x
j
✔ ✔
✔1 ✔ ✔
✔1 ✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔1 ✔ ✔
✔ ✔
✔ ✔ ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
S
SP
P CD h Z M N O H p QRsf U V W F
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔
✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔1
✔1 ✔1 ✔1 ✔1 ✔1 ✔ ✔1 ✔ ✔ ✔ ✔ ✔1 ✔1 ✔1 ✔1
✔
✔ ✔ ✔ ✔
✔
✔ ✔ ✔ ✔
✔
✔
✔ ✔ ✔ ✔ ✔ ✔ ✔
6
6
6
6
6
6
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔6 ✔6 ✔6 ✔6
✔
✔ ✔ ✔ ✔
✔
✔
✔ ✔ ✔ ✔ ✔ ✔ ✔
✔
✔
✔ ✔ ✔ ✔
✔
✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
1
1
✔1 ✔1 ✔ ✔ ✔1 ✔ ✔ ✔ ✔1 ✔ ✔1 ✔1 ✔5
✔ ✔
✔ ✔ ✔
✔
✔5
✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔6 ✔6 ✔6 ✔6 ✔6 ✔6 ✔6 ✔6 ✔6 ✔6 ✔6 ✔6
✔ ✔ ✔ ✔
✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔
✔
✔
✔
✔
✔
✔
✔
r
u
i 1920×1080
h 1280×720
f 640×480
k 640×480
k 320×240
k 320×112
N
L
l
M
m
OFF
R
ON
OFF
ON
OFF
n
o
ON
OFF
✔
✔ ✔ ✔
✔1 ✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔
✔ ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1 ✔1 ✔1 ✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔ ✔ ✔ ✔ ✔ ✔
✔
✔ ✔ ✔ ✔
✔
✔ ✔ ✔ ✔ ✔
✔
✔ ✔ ✔ ✔
1
✔ ✔ ✔ ✔ ✔ ✔ ✔
✔
✔ ✔ ✔ ✔ ✔
✔
✔
1
1
1
1
1
1
✔ ✔ ✔ ✔ ✔ ✔ ✔
✔
✔ ✔ ✔ ✔ ✔
✔ ✔1 ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔
✔
✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔
✔
✔ ✔
✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1 ✔1
✔1 ✔1
✔ ✔
✔ ✔
✔ ✔ ✔ ✔ ✔
✔
✔ ✔
✔
✔ ✔ ✔
✔
✔ ✔
✔
✔ ✔ ✔
✔1 ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔ ✔
✔ ✔
✔ ✔ ✔1 ✔ ✔
✔ ✔
✔
✔ ✔ ✔1 ✔1 ✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1 ✔1 ✔1
✔
✔1 ✔1 ✔
✔ ✔ ✔
✔ ✔ ✔
✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1
Restrictions on Camera Settings
Shooting Mode
Option
d
f
q
r
s
h
I
K
E
Adv.
R S T U B Arij j i M A
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
1 Automatically optimized for selected shooting mode.
2 Image sizes over Q are set to Q.
3 Image sizes over P are set to P.
4 Aspect ratio fixed at 4 : 3.
3.
5 Fixed at settings before recording a movie.
6 Fixed at the center of the frame.
S
SP
P CD h Z M N O H p QRsf U V W F
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔