FujiFilm 16309733-3-KIT Digital Camera User Manual

TRUE FOOD SERVICE EQUIPMENT, INC.
2001 East Terra Lane • P.O. Box 970 • O’Fallon, Missouri 63366
(636)-240-2400 • FAX (636)272-2408 • INT’L FAX (636)272-7546 • (800)325-6152
Parts Department (800)424-TRUE • Parts Department FAX# (636)272-9471
I NSTALL ATIO N M AN U AL F O R
BAR EQ UI PMENT AND G LAS S C H ILLE R S
TABLE OF CONTENTS
TDD-4
TD-50-18-S-LT
TBB-2
TBB-3G-S
Safety Information
Safety Precautions
Proper Disposal
Connecting Electricity
Adapter Plugs
1
2
3
3
Installation / Operation Instructions
Ownership
Required Tools
Uncrating
Location
Leveling Cabinet
Wire Gauge Cart
Sealing Cabinet to the floor
Electrical Instructions
Beer Dispensers
Start-up and Light Switch Location
Shelving & Bin Divider Installation
Storage & Handling
Temperature/Pressure/Tapping
Draft Beer Problems
4
4
4
5
5
6
7
8
8-9
9
10
10
11
12
Maintenance, Care & Cleaning
Temperature Control Adjustment
Changing CO2 Gas Cylinder
Cleaning Bar System
Cleaning the Condenser
Important Warranty Information
Stainless Steel Equipment Care & Cleaning
Lightbulb Replacement
Warranty (U.S.A. and Canada ONLY!)
13
14
15
16
17
18-19
20
21
*Spanish, German, French, and Dutch versions included.
TDB-24-48-1-G-1
CONGRATULATIONS!
You have just purchased the finest commercial
refrigerator available. You can expect many years of
trouble-free operation.
B AR E QUIPMENT AND
GL A SS C HILLERS
............ www.truemfg.com ............
9/8/08-18K SB #894417
True Food Service Equipment, Inc.
............ www.truemfg.com ............
True Food Service Equipment, Inc.
SAFETY INFORMATION
How to Maintain Your lkkkfdls
Unit to Receive the Most Efficient and
Successful Operation
You have selected one of the finest commercial refrigeration units made. It is manufactured under
strict quality controls with only the best quality materials available. Your TRUE cooler when
properly maintained will give you many years of trouble-free service.
WARNING!
Use this appliance for its intended purpose as described in this Owner Manual.
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
• This refrigerator must be properly installed
and located in accordance with the Installation
Instructions before it is used.
• Do not allow children to climb, stand or hang
on the shelves in the refrigerator. They could
damage the refrigerator and seriously injure
themselves.
• Do not touch the cold surfaces in the freezer
compartment when hands are damp or wet.
Skin may stick to these extremely cold surfaces.
• Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
• Keep fingers out of the “pinch point” areas;
clearances between the doors and between
the doors and cabinet are necessarily small; be
careful closing doors when children are in the
area.
1
NOTE: We strongly recommend that any
servicing be preformed by a qualified
individual.
• Unplug the refrigerator before cleaning and
making repairs.
• Setting temperature controls to the 0 position
does not remove power to the light circuit,
perimeter heaters, or evaporator fans.
............ www.truemfg.com ............
1
True Food Service Equipment, Inc.
SAFETY INFORMATION
DANGER!
RISK OF CHILD ENTRAPMENT
PROPER DISPOSAL OF THE REFRIGERATOR
Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are
still dangerous… even if they will sit for “just a few
days.” If you are getting rid of your old refrigerator,
please follow the instructions below to help
prevent accidents.
Before You Throw Away Your Old Refrigerator or
Freezer:
• Take off the doors.
• Leave the shelves in place so that children may
not easily climb inside.
Refrigerant Disposal
Your old refrigerator may have a cooling system
that uses “Ozone Depleting ” chemicals. If you are
throwing away your old refrigerator, make sure
the refrigerant is removed for proper disposal by
a qualified service technician. If you intentionally
release any refrigerants you can be subject to
fines and imprisonment under provisions of the
environmental regulations.
USE OF EXTENSION CORDS
NEVER USE AN EXTENSION CORD! TRUE will not warranty any refrigerator that has been connected to an
extension cord.
2
............ www.truemfg.com ............
2
True Food Service Equipment, Inc.
SAFETY INFORMATION
WARNING!
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall outlet to
minimize the possibility of electric shock hazard
from this appliance.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
If the outlet is a standard 2-prong outlet, it is your
personal responsibility and obligation to have it
replaced with the properly grounded 3-prong wall
outlet.
The refrigerator should always be plugged into
it’s own individual electrical circuit, which has a
voltage rating that matches the rating plate.
This provides the best performance and also
prevents overloading building wiring circuits which
could cause a fire hazard from overheated wires.
Never unplug your refrigerator by pulling on the
power cord. Always grip plug firmly and pull
straight out from the outlet.
Repair or replace immediately all power cords that
have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end.
When removing the refrigerator away from the wall,
be careful not to roll over or damage the power
cord.
USE OF ADAPTER PLUGS
NEVER USE AN ADAPTER PLUG! Because of potential safety hazards under certain conditions, we strongly
recommend against the use of an adapter plug.
(North America Use Only!)
NEMA plugs
TRUE uses these types of plugs.
If you do not have the right outlet
have a certified electrician install
the correct power source.
115/60/1
NEMA-5-15R
3
............ www.truemfg.com ............
3
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
INSTALLATION / OPERATION INSTRUCTIONS
OWNERSHIP
To insure that your unit works properly from the
first day, it must be installed properly. We highly
recommend a trained refrigeration mechanic and
electrician install your True equipment. The cost of
a professional installation is money well spent.
Before you start to install your True unit, carefully
inspect it for freight damage. If damage is
discovered, immediately file a claim with the
delivery freight carrier.
True is not responsible for damage incurred during
shipment.
REQUIRED TOOLS
•
•
•
Adjustable Wrench
Phillips Head Screwdriver
Level
UNCRATING
Step 1
The following procedure is recommended for
uncrating the unit:
A. Remove the outer packaging, (cardboard
and bubbles or styrofoam corners and clear
plastic). Inspect for concealed damage. Again,
immediately file a claim with the freight carrier
if there is damage.
B. Move your unit as close to the final location as
possible before removing the wooden skid.
C. Remove door bracket on swinging glass door
models (see image 1-2).
Note: Keys for coolers with door locks are located in
warranty packets.
1
2
• Contact True Technical Service for BTU
REMOTE UNITS (This section applies to remotes
requirements.
only!)
• No wiring necessary between cabinet and
• Remote cabinets must be ordered as remote.
condensing unit.
We do not recommend converting for a
standard self contained to remote system.
• All remote condensing units purchased from
True are 208/230 volts single phase.
• All remote cabinets must be hard wired.
If you have any questions regarding this section,
• No castors available.
please call True at 1-(800)-325-6152.
• All remote cabinets come standard using 404A
refrigerant.
• All remote units come standard with expansion
valve, liquid line solenoid, heated condensate
pan, and defrost timer when applicable.
4
............ www.truemfg.com ............
4
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
LOCATING
TOOLS REQUIRED:
• Phillips screw driver
• 3/8” socket or 3/8” wrench
Step 2
A. Use a phillips screw diver and remove four
screws from the L-bracket connected the unit
to the wood skid (see image 1). Then use a 3/8”
socket or wrench and remove the L-bracket
from the unit (see image 2).
When lifting unit do not use the countertop as
a lifting point. Also remember to leave cabinet
upright for 24 hours before plugging
into power source.
B. Remove skid by unscrewing all base rail anchor
brackets. Place skid to the side.
C. Carefully upright cabinet.
(Image 1)
Removing
bracket from
skid.
(Image 2)
Removing
bracket from
cabinet.
LEVELING
Step 3
A. Set unit in its final location. Be sure there is
adequate ventilation in your room. Under extreme
heat conditions, (100°F+, 38°C+), you may want to
install an exhaust fan.
Warning
Warranty is void if ventilation is insufficient.
B. Proper leveling of your True cooler is critical to
operating success (for non-mobile models). Effective
condensate removal and door operation will be
effected by leveling.
C. The cooler should be leveled front to back and
side to side with a level.
5
D. Ensure that the drain hose or hoses are
positioned in the pan.
E. Free plug and cord from inside the lower rear of
the cooler (do not plug in).
F. The unit should be placed close enough to the
electrical supply so that extension cords are never
used.
Warning
Compressor warranties are void if the unit is more than
7 ft. (2.1m) from plug-in connection or an extension
cord is used to connect unit to a power supply.
............ www.truemfg.com ............
5
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
CONDUCTORS AND CIRCUITS
Wire Gauge for 2% Voltage Drop in Supply Circuits.
115 Volt
Amps 20
30
Distance In Feet To Center of Load
40 50 60 70 80 90 100 120 140 160
2
3
4
5
6
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
12
14
14
14
12
12
14
14
14
12
12
14
14
12
12
10
14
14
12
10
10
14
12
12
10
10
7
8
9
10
12
14
14
14
14
14
14
14
14
14
14
14
14
14
14
12
14
14
12
12
12
14
12
12
12
10
12
12
12
10
10
12
12
10
10
10
12
10
10
10
8
10
10
10
10
8
10
10
8
8
8
10
8
8
8
8
8
8
8
8
6
14
16
18
20
25
14
14
14
14
12
14
12
12
12
10
12
12
10
10
10
10
10
10
10
8
10
10
8
8
8
10
8
8
8
6
8
8
8
8
6
8
8
8
6
6
8
8
8
6
6
6
6
8
6
5
6
6
8
5
4
6
6
5
5
4
30
35
40
45
50
12
10
10
10
10
10
10
8
8
8
8
8
8
6
6
8
6
6
6
6
6
6
6
6
5
6
6
5
5
4
6
5
5
4
4
6
5
4
4
3
5
4
4
3
3
4
4
3
3
2
4
3
2
2
1
3
2
2
1
1
Wire Gauge for 2% Voltage Drop in Supply Circuits.
230 Volt
Amps 20
6
30
Distance In Feet To Center of Load
40 50 60 70 80 90 100 120 140 160
5
6
7
8
9
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
12
14
14
14
12
12
14
14
12
12
12
14
12
12
12
10
10
12
14
16
18
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
12
14
14
14
12
12
14
14
12
12
12
14
12
12
12
10
12
12
12
10
10
12
12
10
10
10
12
10
10
10
8
10
10
10
8
8
10
10
8
8
8
20
25
30
35
40
14
14
14
14
14
14
14
12
12
12
14
12
12
10
10
12
12
10
10
10
10
10
10
10
8
10
10
10
8
8
10
10
8
8
8
10
10
8
8
6
10
8
8
8
6
8
8
6
6
6
8
6
6
6
5
8
6
6
5
5
50
60
70
80
90
100
12
12
10
10
10
10
10
10
10
8
8
8
10
8
8
8
6
6
8
6
6
6
6
6
6
6
6
6
5
5
6
6
6
5
5
4
6
6
5
5
4
4
6
6
5
4
4
3
6
5
4
4
3
3
5
4
4
3
3
2
4
4
2
2
1
1
4
3
2
2
1
1
............ www.truemfg.com ............
6
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
SEALING CABINET TO FLOOR
Step 1 - Position Cabinet
Allow one inch between the wall and rear of
the refrigerated Bar Equipment to assure proper
ventilation. For Glass & Plate Chillers/Frosters 3
inches between the wall and rear of the cabinet will
assure proper ventilation.
Step 2 - Level Cabinet
Cabinet should be level, side to side and front to
back. Place a carpenter’s level in the interior floor
in four places:
A. Position level in the inside floor of the unit
near the doors. (Level should be parallel to cabinet
front). Level cabinet.
B. Position level at the inside rear of cabinet.
(Again level should be placed parallel to cabinet
back).
C. Perform similar procedures to steps A & B by
placing the level on inside floor (left and right
sides - parallel to the depth of the cooler). Level
cabinet.
Step 3
Draw an outline on the base on the floor.
Step 4
Raise and block the front side of the cabinet.
Step 5
Apply a bead of “NSF Approved Sealant”, (see list
below), to floor on half inch inside the outline
drawn. The bead must be heavy enough to seal
the entire cabinet surface when it is down on the
sealant.
7
Step 6
Raise and block the rear of the cabinet
Step 7
Apply sealant on floor as outlined in Step 5 on
other three sides.
Step 8
Examine to see that cabinet is sealed to floor
around entire perimeter.
Note:
Asphalt floors are very susceptible to chemical
attack. A layer of tape on the floor prior to
applying the sealant will protect the floor.
NSF Approved Sealants:
1. Minnesota Mining #ECU800 Caulk
2. Minnesota Mining #ECU2185 Caulk
3. Minnesota Mining #ECU1055 Bead
4. Minnesota Mining #ECU1202 Bead
5. Armstrong Cork - Rubber Caulk
6. Products Research Co. #5000 Rubber Caulk
7. G.E. Silicone Sealer
8. Dow Corning Silicone Sealer
............ www.truemfg.com ............
7
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
ELECTRICAL INSTRUCTIONS
WARNING
Compressor warranties are void if compressor burns
out due to low voltage.
Step 4
A. Before your new unit is connected to a
power supply, check the incoming voltage with a
voltmeter. If anything less than 100% of the rated
voltage for operation is noted, correct immediately.
B. All units are equipped with a 7 ft. (2.1m) service
cord, and must be powered at proper operating
voltage at all times. Refer to cabinet data plate for
this voltage.
True recommends that a sole use circuit be
dedicated for the unit.
WARNING
Power supply cord ground should not be removed!
NOTE
To reference wiring diagram - Remove front louvered
grill, wiring diagram is positioned on the inside cabinet
wall.
BEER DISPENSERS
CAUTION
Filled CO2 tanks are potentially dangerous
because of the pressure they contain. If you
are unfamiliar with their use or the use of the
CO2 regulator, seek information from your local
distributor, or your local beverage man before
proceeding.
On beer dispensers the drain is located at the
front of the cabinet. To plumb in the drain,
connect 34⁄ " (2cm) P.V.C. pipe to the 34⁄ " (2cm)
barbed fitting supplies with the unit.
CO2 PRESSURE
Mobile tapsters, to retain complete mobility,
the CO2 tank (up to five pounds in size) can
be placed inside the cooler (strap holders
furnished).
INSTALL DRAFT ARM
Place rubber washer over draft arm mounting
holes in cabinet, put beer line connector
down through hole. Next, secure draft arm
with four screws. (See images 1-6)
2
Beer line
connector.
1
3
Draft arm install contents.
(Draft arm not shown)
Thread
beer draft
arm handle
onto the
draft arm.
6
8
4
5
Thread beer line connector to draft arm and secure draft
arm to cabinet with rubber gasket under the draft arm.
CONTINUED ON
NEXT PAGE...
............ www.truemfg.com ............
8
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
BEER DISPENSERS CONTINUED...
INSTALL DRAFT ARM continued...
Insert air hose (one inch plastic tube)
in draft arm, being careful not to disturb
insulation. Remove top cover of draft
arm and attach air hose clip to the
insulating sleeve at the top of the draft
arm. Replace top cover. The air hose
clip will assure that the hose remains
in proper place at all times, keeping the
beer faucet cold. (See image 7-9)
7
8
9
STARTUP
Step 5
A. The compressor is ready to operate. Plug in the
cooler.
B. Temperature control set at No. 4 position gives
refrigerators an approximate temperature of 35°F
and glass chiller frosters have an approximate
temperature of 0°F. Allow unit to function several
hours, completely cooling cabinet before changing
the control setting.
C. Excessive tampering with the control could
lead to service difficulties. Should it ever become
necessary to replace temperature control, be sure it
is ordered from your True dealer or recommended
service agent.
D. Good air flow in your True unit is critical. Be
careful to load product so that it neither presses
against the back wall, nor comes within four inches
of the evaporator housing. Refrigerated air off the
coil must circulate down the back wall.
NOTE
If the unit is disconnected or shut off, wait five minutes
before starting again.
RECOMMENDATION
Before loading product we recommend you run your
True unit empty for two to three days. This allows you
to be sure electrical wiring and installation are correct
and no shipping damage has occurred. Remember, our
factory warranty does not cover product loss!
REPLACEMENT PARTS
TRUE maintains a record of the cabinet serial number
for your cooler. If at any time during the life of your
cooler, a part is needed, you may obtain this part by
furnishing the model number and serial number to the
company from whom you purchased the cooler. Call
Toll-Free: (800)-424-TRUE (Direct to Parts Department).
(800)-325-6152 (U.S.A. & Canada only) or call: (636)240-2400.
LIGHT SWITCH LOCATION:
The switch is located on the front of the
evaporator housing toward the front of the
cabinet. Open the front doors and the switch will
be visible close to the ceiling the cabinet.
9
............ www.truemfg.com ............
9
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
SHELVING and BIN DIVIDER INSTALLATION /
OPERATION
SHELF INSTALLATION:
A. Hook shelf clips onto shelf standards.
SHELF INSTALLATION
B. Position all four shelf clips equal in distance
from the floor for flat shelves.
C. Shelves are oriented so that cross support bars
are facing down.
Shelf
Standards
D. Place shelves on shelf clips making sure all
corners are seated properly.
Shelf
HORIZONTAL BOTTLE COOLER BIN DIVIDER
INSTALLATION:
Horizontal bottle coolers are shipped with bin
dividers in place. If it is necessary to adjust spacing
the following procedure is recommended.
Step 1
A. Dividers are spring loaded - push divider
towards rear of the cooler to release from front
grommeted holes.
Pillaster
(I-beam)
BIN DIVIDER INSTALLATION
;;
;;;;;
;;;;;;;
;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;
;;;;;;
;;;;;;
;;;;;;
;;;;;;
;;;;;;
;;;;;;
;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;
;;;;;;
;;;;;;
;;;;;;
;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;
;;;;;;
;;;;;;
;
;;;;;;
;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;
;;;;;;
;;;;;;
;;;;;;
;;;;;;
;;;;;;
;;;;;;
;;;;;;
;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;
;;;;;;;;;;;;
;;;;;;
;;;;;;
;;;;;;
;;;;;;
;;;;;;
;;;;;;
;;;;;;
;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
;;;;;;;;;;;;
1 OFF
4 3 2
NOTE:
Divider positioned
in front of
mechanical box
requires specific
notch cut out.
6 5
Remove divider from the front holes and line up
regular and spring loaded rear pegs with holes in
line with those desired in front. Insert as far as
possible and maneuver front pegs in place.
Shelf
Clip
9 8 7
B. Lineup divider front pegs with desired holes
and punch through interior tape lining of both top
and bottom holes - bottom peg first (front holes are
taped over to improve insulation values).
Shelf
STORAGE AND HANDLING
Draft beer should be treated as a food product. In
most instances draft beer is not pasteurized. It is
very important that you store and handle it properly.
Follow these steps to ensure the highest quality and
consumer satisfaction.
• Draft beer should be immediately stored in a
refrigerated cabinet.
• Draft beer products have a recommended shelf
life. If you have questions regarding the shelf life
10
of any of your draught products, please consult
with your supplying depot or respective Brewer
representative.
• Kegs should be stored separately from food
products. If your cooler is used to refrigerate
draught and food products, it is very important that
the food not be stored near or on the kegs.
• Keg storage and dispensing areas should be kept
clean to prevent any possibility of contaminating
your draught products.
............ www.truemfg.com ............
10
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
TEMPERATURE
• Correct temperature is a key factor to consider in
storing and dispensing draft beer. Too cool or too warm
may cause flavor loss, off taste and dispensing problems.
Helpful Hints on Controlling Temperature
• Keep a thermometer handy
•
Monitor temperature of draft in your
cooler and at the tap
• Keep cooler door closed as much as
possible to avoid temperature fluctuation
• Regular maintenance of refrigeration
equipment is recommended
PRESSURE
Dispensing pressures differ according to:
• The type of draft dispensing system
• The length of draft dispensing line
• The actual product - some require
more, some require less
• The temperature of the product
• The pressurizing agent: air pressure,
CO2 or special blended gases.
Helpful Hints On Maintaining The Correct Pressure:
• Know which pressurizing agent to
use on which product and why.
• Monitor your regulators to ensure
applied pressure remains constant
• Keep equipment in good repair
TAPPING
Do not agitate the kegs unnecessarily. If excessive
agitation occurs allow kegs to settle for 1 to 2 hours
before tapping.
Prior to tapping the keg, ensure that all beer faucet in
the serving location are in the off position. Completely
remove the dust cover (identification cap) from the keg.
TDD-1 CO2 KNOCK-OUT
STEP 1
Remove black knockout plug with a
pair of pliers.
STEP 4
Seal hole around CO2 line with
silicone sealer to prevent cold air
leakage.
NOTE:
Knockout plug for CO2 line can be
locate in two different areas. View
diagram to locate these two areas.
11
FF O
6 5
3 4
STEP 3
Snake CO2 line through hole down
and around exiting behind rear castor
underneath rear grill.
2
REQUIRED TOOLS
• Pliers
• Power Drill
• Silicone Sealer
• Drill bit, 1/2”
STEP 2
Use drill and bit to bore hole straight
back through wall into compressor
compartment.
7 8 9
This instruction is True’s
recommended procedure for installing
a remote CO2 container.
............ www.truemfg.com ............
Knockout Plug
can be located at
either location.
11
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
DRAFT BEER PROBLEMS
To minimize draft beer problems, always follow the recommended
instructions for temperature and CO2 pressures from your beer supplier.
Flat Beer - Description: Foamy head
disappears quickly. Beer lacks usual
zestful brewery fresh flavor.
• CO2 turned off when not in use.
• Contaminated air source (associated
with compressed air).
• Greasy glasses.
• Not enough pressure.
• Pressure shut off during night.
• Loose tap or vent connection.
• Sluggish pressure regulator.
• Obstruction in lines.
False Head - Description: Large soap-like
bubbles, head dissolves very quickly.
• Dry glasses.
• Improper pour.
• Pressure required does not correspond
to beer temperature.
• Coils or direct draw beer lines warmer
than beer in keg.
• Small lines into large faucet shanks.
• Beer drawn improperly.
Cloudy Beer - Description: Beer in the glass
appears hazy. Not clear.
• Dirty glass or faucet.
• Beer over chilled.
• Beer temperature variance in keg (Beer
may have warmed up at sometime).
• Hot spots in beer lines.
• Cutting beer through faucet.
• Beer line in poor condition.
• Dirty lines.
• Beer that has been frozen.
Bad Taste
• Dirty faucet.
• Old or dirty beer lines.
• Failure to flush beer lines with water
after each empty keg.
• Unsanitary conditions at bar.
• Foul air or dirt in lines.
• Oily air; greasy kitchen air.
• Temperature of package too warm.
• Dry glasses
Wild Beer - Description: Beer, when drawn,
is all foam and not enough liquid beer.
• Beer drawn improperly.
• Faucet in bad or worn condition.
• Kinks, dents, twists or other
obstructions in line.
• Traps in beer lines.
• Beer too warm in kegs or lines.
• Too much pressure.
• Creeping gauge causing too much
pressure.
12
............ www.truemfg.com ............
12
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
TEMPERATURE CONTROL ADJUSTMENT FOR
HIGH ALTITUDE ONLY!
__________ STEP 4 ___________
TERMS:
Cut-out - Temperature sensed
by the controller that shuts the
compressor off.
Cut-in - Temperature sensed by
the controller that turns the
compressor on.
REQUIRED TOOLS
• Phillips Head Screwdriver
• 5/64" or 2 mm Allen Wrench
• T-7 Torx Wrench
__________ STEP 1 ___________
For high elevation installations,
it may be necessary to "warmup" the set points. To make
the adjustment, insert the
appropriate tool in each
adjustment screw and turn 1/4
of a revolution clockwise (to the
right). This procedure will adjust
both the cut-in and cut-out about
2°F warmer.
__________ STEP 5 ___________
Make sure to reconnect the
pink wire to the proper spade
terminal when reinstalling.
Unplug the cooler.
__________ STEP 2 ___________
Remove the screws that secure
the temperature control to the
inset box.
__________ STEP 3 ___________
Danfoss Temperature Control (High Altitude Adjustment Only!)
Pull out gently from cabinet.
Cut-out Adjustment Screw Allen (5/64"
or 2 mm) (clockwise for warmer)
NOTE:
Cut-in Adjustment Screw Torx (T-7)
(clockwise for warmer)
Mechanical temperature
controllers are affected when
functioning at high altitude. The
cut-in and cut-out
temperatures will be colder than
when the controller functions
closer to sea level
13
Compressor Connection (pink)
Compressor Connection (pink)
............ www.truemfg.com ............
13
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
CHANGING CO2 GAS CYLINDER
Follow these instructions at ALL times when you
replace a CO2 gas cylinder:
1. Close cylinder at "A".
2. Remove tap "D" from barrel. Pull pressure
release ring on body of tap to release pressure
remaining in line. (do not close "C")
3. Remove or loosen regulator key "B" by turning
counter clockwise.
4. Remove regulator from used cylinder at "E".
5. Remove dust cap from new gas cylinder at
"E" and clear dust from outlet by opening and
closing valve "A" quickly using appropriate
wrench.
6. Attach regulator to new cylinder at "E". (use
new fiber/plastic washer, if required).
7. Open valve "A" all the way.
8. Close valve "C".
9. Adjust regulator key "B" by turning clockwise
to set pressure. (check setting by opening "C"
and pulling and releasing the ring "F" on the
pressure release valve on the body of the tap)
10. Tap barrel at "D" with valve "C" open.
Decreasing Pressure:
1. Close regulator shut-off "C".
2. Untap barrel at "D" and to bleed line, activate
tap handle. Leave in open position.
3. Slowly open regulator shut-off "C" and
simultaneously turn regulator key counterclockwise to zero reading.
4. Close regulator shut-off "C" and set pressure by
turning regulator key clockwise. Check setting
by opening and closing valve "C".
5. Close tap head "D". (put in "OFF" position)
6. Tap barrel at "D" and open regulator shut-off "C".
D
F
NOTE
Don't lay CO2 cylinders flat.
Don't drop CO2 cylinders.
A
B
E
It requires 1/2 pound CO2 to dispense 1/2 barrel of
beer at 38˚F with 15 pounds pressure on barrel.
C
PRESSURE ADJUSTMENT ON CO2
REGULATOR
Increasing Pressure:
1. Close regulator shut-off "C".
2. Turn regulator key "B" clockwise and make
setting.
3. Tap gauge for accurate reading.
4. Open regulator shut-off "C" and draw beer.
14
............ www.truemfg.com ............
14
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
CLEANING BAR SYSTEM
Draught dispensers, regardless of design, must be
cleaned at least every two weeks. Flushing your
draught dispenser with water only is not enough.
Note: Use cleaners approved by your beer supplier
and follow their instructions. If you are using
the cleaning kit purchased from True follow these
instructions:
Exacting cleanliness should be constantly maintained
in your dispenser so that your draught beer will be at
its best when served. Although the beer in the barrel
is in excellent condition, it can become less satisfying
as it is drawn through the beer line and faucet if they
are not kept clean.
Prepare Solution:
• Add 1/2 ounce (19 grams) of line cleaning
powder to each quart of water, cold or warm.
Cleaning:
1. Disconnect tap from barrel. Remove beer faucet
with spanner wrench unscrew handle and
remove valve assembly (fig. 1).
2. Put tap and faucet parts in a bucket with
cleaning solution to soak.
3. Use small brush to clean beer faucet parts
(fig. 2).
4. Rinse parts Thoroughly.
5. Fill pump bottle with DBK solution.
6. Attach hose from pump bottle to beer column
tap outlet (be sure rubber gasket is in place to
prevent leakage) - allow tap to drain in bucket
(fig. 3).
7. Pump solution (2-3 times from bottle through
the line until it starts to flow out the beer line.
Wait 10 minutes while cleaning solution works on the
lines.
8. Pump excess solution through lines.
9. Rinse bucket, pump bottle and hose thoroughly
with clean cool water.
10. Fill pump bottle with clean cool water and
pump through lines until water runs clear.
11. When crystal clear water comes through, you're
ready to assemble and reattach faucet and re-tap
the barrel.
12. Draw the water from the beer line; now you're
ready to serve brewery fresh, golden beer.
NOTE
Keeping your dispenser and all its parts clean and
odor free will help you to serve beautiful foam topped
glasses of delicious satisfying draught beer.
Beer Tap Cleaning Kit
Required Tools
line cleaning
powder
Pump bottle
and tub
15
Spanner
wrench
Bucket and
fresh water
Brush
fig. 1
fig. 2
............ www.truemfg.com ............
fig. 3
15
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
MAINTENANCE, CARE & CLEANING
CLEANING THE CONDENSER COIL
When using electrical appliances, basic safety precautions should be followed, including the following:
STEP 5
Lift cardboard cover above fan at plastic plugs and
carefully clean condenser coil and fan blades.
REQUIRED TOOLS
• Phillips Screwdriver
• Stiff Bristle Brush
• Adjustable Wrench
STEP 1
Disconnect power to unit.
STEP 6
After brushing condenser coil vacuum dirt from
coil, and interior floor.
STEP 2
Take off lower grill assembly by removing all
screws.
STEP 7
Replace cardboard cover. Carefully slide
compressor assembly back into position and
replace bolts.
STEP 3
Remove bolts anchoring compressor assembly
to frame rails and carefully slide out. (tube
connections are flexible)
STEP 8
Reinstall louver assembly onto unit with
appropriate fasteners and clips. Tighten all screws.
STEP 4
Clean off accumulated dirt from condensing coil
with a stiff bristle brush.
STEP 9
Connect unit to power and check to see if
condenser is running.
T
M
C
TRUE
16
............ www.truemfg.com ............
16
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
IMPORTANT WARRANTY INFORMATION
Condensers accumulate dirt and require cleaning every 30 days. Dirty condensers result in
compressor failure, product loss, and lost sales... which are not covered by warranty.
If you keep the Condenser clean you will minimize your service expense and lower your electrical costs. The
Condenser requires scheduled cleaning every thirty days or as needed.
Air is pulled through the Condenser continuously, along with dust, lint, grease, etc.
A dirty Condenser can result in NON-WARRANTEED part & Compressor Failures, Product Loss, and Lost Sales.
Proper cleaning involves removing dust from the Condenser. By using a soft brush, or vacuuming the Condenser
with a shop vac, or using CO2, nitrogen, or pressurized air.
If you cannot remove the dirt adequately, please call your refrigeration service company.
On most of the reach-in units the condenser is accessible in the rear of the unit. You must remove the cabinet
grill to expose the Condenser.
The Condenser looks like a group of vertical fins. You need to be able to see through the condenser for the unit
to function at maximum capacity. Do not place filter material in front of condensing coil. This material blocks
air-flow to the coil similar to having a dirty coil.
THE CLEANING OF THE CONDENSER IS NOT
COVERED BY THE WARRANTY!
Airflow
HOW TO CLEAN THE CONDENSER:
1. Disconnect the electrical power to the unit.
Conden
sing Un
2. Remove the louvered grill.
it
Condenser
3. Vacuum or brush the dirt, lint, or debris from the finned condenser coil.
4. If you have a significant dirt build up you can blow out the condenser with compressed air.
(CAUTION MUST BE USED to avoid eye injury. Eye protection is recommended.)
5. When finished be sure to replace the louvered grill. The gill protects the condenser.
6. Reconnect the electrical power to the unit.
If you have any questions, please call True Manufacturing at 636-240-2400 or 800-325-6152 and ask for the
Service Department. Service Department Availability Monday-Friday 7:30 a.m. to 5:30 p.m.
and Saturday 7:45 a.m. to 11:45 a.m. CST.
17
............ www.truemfg.com ............
17
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
STAINLESS STEEL EQUIPMENT CARE AND CLEANING
CAUTION: Do not use any steel wool, abrasive or chlorine based products to clean stainless steel surfaces.
• Stainless Steel Opponents
There are three basic things which can break down your stainless steel’s passivity layer and allow
corrosion to rear its ugly head.
1) Scratches from wire brushes, scrapers, and steel pads are just a few examples of items that can be
abrasive to stainless steel’s surface.
2) Deposits left on your stainless steel can leave spots. You may have hard or soft water depending on
what part of the country you live in. Hard water can leave spots. Hard water that is heated can
leave deposits if left to sit too long. These deposits can cause the passive layer to break down and
rust your stainless steel. All deposits left from food prep or service should be removed as soon as
possible.
3) Chlorides are present in table salt, food, and water. Household and industrial cleaners are the worst
type of chlorides to use.
8 steps that can help prevent rust on stainless steel:
1. Using the correct cleaning tools
Use non-abrasive tools when cleaning your stainless steel products. The stainless steel’s passive layer will not
be harmed by soft cloths and plastic scouring pads. Step 2 tells you how to find the polishing marks.
2. Cleaning along the polish lines
Polishing lines or “grain” are visible on some stainless steels. Always scrub parallel to visible lines on some
stainless steels. Use a plastic scouring pad or soft cloth when you cannot see the grain.
3. Use alkaline, alkaline chlorinated or non-chloride containing cleaners
While many traditional cleaners are loaded with chlorides, the industry is providing an ever increasing choice
of non-chloride cleaners. If you are not sure of your cleaner’s chloride content contact your cleaner supplier.
If they tell you that your present cleaner contains chlorides, ask if they have an alternative. Avoid cleaners
containing quaternary salts as they can attack stainless steel, causing pitting and rusting.
4. Water Treatment
To reduce deposits, soften the hard water when possible. Installation of certain filters can remove corrosive
and distasteful elements. Salts in a properly maintained water softener can be to your advantage. Contact a
treatment specialist if you are not sure of the proper water treatment.
5. Maintaining the cleanliness of your food equipment
Use cleaners at recommended strength (alkaline, alkaline chlorinated or non-chloride). Avoid build-up of hard
stains by cleaning frequently. When boiling water with your stainless steel equipment, the single most likely
cause of damage is chlorides in the water. Heating any cleaners containing chlorides will have the same
damaging effects.
6. Rinse
When using chlorinated cleaners you must rinse and wipe dry immediately. It is better to wipe standing
cleaning agents and water as soon as possible. Allow the stainless steel equipment to air dry. Oxygen helps
maintain the passivity film on stainless steel.
7. Hydrochloric acid (muriatic acid) should never be used on stainless steel
8. Regularly restore/passivate stainless steel
18
............ www.truemfg.com ............
18
True Food Service Equipment, Inc.
MAINTENANCE, CARE & CLEANING
STAINLESS STEEL EQUIPMENT CARE AND CLEANING
Recommended cleaners for certain situations / environments of stainless steel
A) Soap, ammonia and detergent medallion applied with a cloth or sponge can be used for routine
cleaning.
B) Arcal 20, Lac-O-Nu Ecoshine applied provides barrier film for fingerprints and smears.
C) Cameo, Talc, Zud First Impression is applied by rubbing in the direction of the polished lines for
stubborn stains and discoloring.
D) Easy-off and De-Grease It oven aid are excellent for removals on all finishes for grease-fatty acids,
blood and burnt-on foods.
E) Any good commercial detergent can be applied with a sponge or cloth to remove grease and oil.
F) Benefit, Super Sheen, Sheila Shine are good for restoration / passivation.
NOTE:
The use of stainless steel cleaners or other such solvents is not
recommended on plastic parts. Warm soap and water will suffice.
19
............ www.truemfg.com ............
19
True Food Service Equipment, Inc.
INSTALLATION / OPERATION INSTRUCTIONS
LIGHT BULB REPLACEMENT (IDL)
INTEGRATED DOOR LIGHTING
Be careful when removing the light bulb.
Please be aware of your local ordinances in
disposing old florescent bulbs. These bulbs
should be disposed in a safe and correct
manner.
WARNING:
When replacing a light bulb make sure
power to the unit is either turned off or
unplugged.
Remove the lampshield to
reveal the bulb. Squeeze
the sides of the lampshield
at the same time pulling it
away from the bulb.
The lamp holders are
spring activated. Pull the
top lamp holder up and
push the bulb down at
the same time. This will
leave enough clearance to
remove the bulb.
20
............ www.truemfg.com ............
20
TRUE REFRIGERATION
True Food Service Equipment, Inc.
TM
MADE IN
U.S.A.
SINCE 1945
WARRANTY INFORMATION (U.S.A. and Canada ONLY!)
ONE YEAR PARTS & LABOR WARRANTY
TRUE warrants to the original purchaser of every new TRUE refrigerated unit, the cabinet and all parts thereof, to be free from defects in material or
workmanship, under normal and proper use and maintenance service as specified by TRUE and upon proper installation and start-up in accordance with
the instruction packet supplied with each TRUE unit. TRUE’s obligation under this warranty is limited to a period of one (1) year from the date of original
installation or 15 months after shipment date from TRUE, whichever occurs first.
Any part covered under this warranty that are determined by TRUE to have been defective within one (1) year of original installation or fifteen (15)
months after shipment date from manufacturer, whichever occurs first, is limited to the repair or replacement, including labor charges, of defective parts or
assemblies. The labor warranty shall include standard straight time labor charges only and reasonable travel time, as determined by TRUE.
ADDITIONAL FOUR YEAR COMPRESSOR WARRANTY
In addition to the one (1) year warranty stated above, TRUE warrants its hermetically and semi-hermetically sealed compressor to be free from defects
in both material and workmanship under normal and proper use and maintenance service for a period of four (4) additional years from the date of original
installation but not to exceed five (5) years and three (3) months after shipment from the manufacturer.
Compressors determined by TRUE to have been defective within this extended time period will, at TRUE’s option, be either repaired or replaced with a
compressor or compressor parts of similar design and capacity.
The four (4) year extended compressor warranty applies only to hermetically and semi-hermetically sealed parts of the compressor and does not apply
to any other parts or components, including, but not limited to, cabinet, paint finish, temperature control, refrigerant, metering device, driers, motor starting
equipment, fan assembly or any other electrical component, etcetera.
404A/134A COMPRESSOR WARRANTY
The four year compressor warranty detailed above will be voided if the following procedure is not carefully adhered to:
1. This system contains R404A or R134A refrigerant and polyol ester lubricant. The polyol ester lubricant has rapid moisture absorbing qualities. If long
exposure to the ambient conditions occur, the lubricant must be removed and replaced with new. For oil amounts and specifications please call True
technical service department (800-325-6152). Failure to comply with recommended lubricant specification will void the compressor warranty.
2. Drier replacement is very important and must be changed when a system is opened for servicing. A drier using XH-7 desiccant or an exact
replacement solid core drier must be used. The new drier must also be the same capacity as the drier being replaced.
3. Micron level vacuums must be achieved to insure low moisture levels in the system. 500 microns or lower must be obtained.
WARRANTY CLAIMS
All claims for labor or parts must be made directly through TRUE. All claims should include: model number of the unit, the serial number of the cabinet,
proof of purchase, date of installation, and all pertinent information supporting the existence of the alleged defect.
In case of warranty compressor, the compressor model tag must be returned to TRUE along with above listed information.
Any action or breach of these warranty provisions must be commenced within one (1) year after that cause of action has occurred.
WHAT IS NOT COVERED BY THIS WARRANTY
TRUE’s sole obligation under this warranty is limited to either repair or replacement of parts, subject to the additional limitations below. This warranty
neither assumes nor authorizes any person to assume obligations other than those expressly covered by this warranty.
NO CONSEQUENTIAL DAMAGES. TRUE IS NOT RESPONSIBLE FOR ECONOMIC LOSS; PROFIT LOSS; OR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES,
INCLUDING WITHOUT LIMITATION, LOSSES OR DAMAGES ARISING FROM FOOD OR PRODUCT SPOILAGE CLAIMS WHETHER OR NOT ON ACCOUNT OF
REFRIGERATION FAILURE.
WARRANTY IS NOT TRANSFERABLE. This warranty is not assignable and applies only in favor of the original purchaser/user to whom delivered. ANY SUCH
ASSIGNMENT OR TRANSFER SHALL VOID THE WARRANTIES HEREIN MADE AND SHALL VOID ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
IMPROPER USAGE. TRUE ASSUMES NO LIABILITY FOR PARTS OR LABOR COVERAGE FOR COMPONENT FAILURE OR OTHER DAMAGES RESULTING FROM
IMPROPER USAGE OR INSTALLATION OR FAILURE TO CLEAN AND/OR MAINTAIN PRODUCT AS SET FORTH IN THE WARRANTY PACKET PROVIDED WITH THE UNIT.
ALTERATION, NEGLECT, ABUSE, MISUSE, ACCIDENT, DAMAGE DURING TRANSIT OR INSTALLATION, FIRE, FLOOD, ACTS OF GOD. TRUE is not responsible for
the repair or replacement of any parts that TRUE determines have been subjected after the date of manufacture to alteration, neglect, abuse, misuse,
accident, damage during transit or installation, fire, flood, or act of God.
IMPROPER ELECTRICAL CONNECTIONS. TRUE IS NOT RESPONSIBLE FOR THE REPAIR OR REPLACEMENT OF FAILED OR DAMAGED COMPONENTS RESULTING
FROM ELECTRICAL POWER FAILURE, THE USE OF EXTENSION CORDS, LOW VOLTAGE, OR VOLTAGE DROPS TO THE UNIT.
NO IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE: THERE ARE NO OTHER WARRANTIES, EXPRESSED, IMPLIED OR
STATUTORY, EXCEPT THE ONE (1) YEAR PARTS & LABOR WARRANTY AND THE ADDITIONAL FOUR (4) YEAR COMPRESSOR WARRANTY AS DESCRIBED ABOVE. THESE
WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, INCLUDING IMPLIED WARRANTY AND MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
OUTSIDE U.S.: This warranty does not apply to, and TRUE is not responsible for, any warranty claims made on products sold or used outside the United
States.
REMOTE CONDENSERS: True warrants the original purchaser of the remote cabinet one year parts and labor coverage for all cabinet parts thereof to
be free from defects in material or workmanship, under normal and proper use and maintenance service, as specified by True. This warranty is limited to the
cabinet only. True assumes no liability for remote condensing units.
21
............ www.truemfg.com ............
21