FujiFilm 2650 Digital Camera User Manual

2.0
Getting Ready
Basic Photography
Advanced Features
Photography
Advanced Features
Playback
Settings
Software Installation
2650
Camera Connection
7
Using FinePixViewer
8
BL00201-200 (1)
Warning
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
This symbol is intended to alert the user to
the presence of uninsulated “dangerous
voltage” within the product’s enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The graphical symbols are located on the bottom
of the case.
This symbol is intended to alert the user
to the presence of important operating
and maintenance (servicing) instructions
in the literature accompanying the
appliance.
For customers in the U.S.A.
FCC Statement
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions : ( 1 ) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
2
CAUTION
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures :
— Reorient or relocate the receiving antenna.
— Increase the separation between the
equipment and receiver.
— Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
— Consult the dealer or an experienced radio/TV
technician for help.
You are cautioned that any changes or
modifications not expressly approved in this
manual could void the user’s authority to operate
the equipment.
Notes on the Grant:
To comply with Part 15 of the FCC rules, this
product must be used with a Fujifilm-specified
ferrite-core USB cable and DC supply cord.
For customers in Canada
CAUTION
This Class B digital apparatus complies with
Canadian ICES- 003.
Please read the Safety Notes (➡P.119)
and make sure you understand them
before using the camera.
3
Contents
Warning .................................................................. 2
Preface ................................................................... 6
Accessories and Attaching the Strap ..................... 7
Nomenclature ......................................................... 8
1 Getting Ready
LOADING THE BATTERIES AND xD-Picture Card ..... 11
Compatible batteries ......................................... 11
xD-Picture Card (sold separately) ..................... 11
SWITCHING ON AND OFF ...................................... 14
SETTING THE DATE AND TIME ............................. 15
Changing the date and time .............................. 16
To change the date display format .................... 17
SELECTING THE LANGUAGE ................................ 18
2 Basic Photography
BASIC OPERATION GUIDE .................................... 19
Q MODE
TAKING PICTURES (A AUTO MODE) .................. 21
■ Viewfinder Lamp Display ............................... 25
Number of Available Frames ............................. 26
USING AF/AE LOCK ................................................ 27
USING THE ZOOM .................................................. 29
FRAMING GUIDELINE FUNCTION ......................... 30
w MODE
4
VIEWING YOUR IMAGES (PLAYBACK) ................. 31
MULTI-FRAME PLAYBACK ..................................... 32
PLAYBACK ZOOM ................................................... 33
ERASING SINGLE FRAME ...................................... 34
3 Advanced Features Photography
Q MODE
SELECTING A AUTO OR S MANUAL .............. 36
PHOTOGRAPHY MENU OPERATION .................... 37
PHOTOGRAPHY AND MOVIE MENU OPTIONS ... 38
PHOTOGRAPHY MENU
y SETTING THE QUALITY .................................. 39
c FLASH ............................................................... 40
AUTO Auto Flash Mode ...................................... 40
n Red-Eye Reduction .................................. 41
c Forced Flash ............................................ 41
b Suppressed Flash .................................... 42
v Slow Synchro ........................................... 42
E MACRO (CLOSE-UP) PHOTOGRAPHY .......... 43
= SELF-TIMER PHOTOGRAPHY ........................ 44
a WHITE BALANCE
(SELECTING THE LIGHT SOURCE) ............... 46
d EV (EXPOSURE COMPENSATION) ................ 47
T MODE
T MOVIE (VIDEO) ................................................ 48
■ xD-Picture Card standard shooting time ........ 48
Quality settings for movies ................................ 51
4 Advanced Features Playback
w MODE
PLAYING BACK MOVIES ........................................ 52
■ Playing Back Movies ..................................... 53
PLAYBACK MENU
p ERASING SINGLE •
ALL FRAMES/FORMATTING .......................... 54
k PROTECTING IMAGES FRAME/ALL .............. 58
i HOW TO SPECIFY PRINT OPTIONS (DPOF) ....... 62
i DPOF SET FRAME .......................................... 63
5 Settings
g ADJUSTING THE MONITOR BRIGHTNESS ......... 67
g USING SET–UP .................................................. 68
■ List of settings ................................................ 69
■ SET–UP Menu Options ................................. 69
7.3 Use at PC-CAM mode ........................................ 87
7.4 Disconnecting the Camera ................................. 90
8 Using FinePixViewer
8.1 Saving Images on Your Computer and viewing images .. 92
8.2 Making a FinePix CD Album ............................... 93
8.3 Using the FinePix Internet Service ..................... 94
8.3.1 User FAQ ................................................... 94
8.3.2 User Registration ....................................... 94
8.4 Mastering FinePixViewer .................................... 98
8.5 Uninstalling the Software .................................... 99
1
2
3
SET–UP
g POWER SAVE .................................................... 70
6 Software Installation
6.1 The Software Components ................................. 71
6.2 Installation on a Windows PC ............................. 72
6.2.1 Load the CD-ROM into your PC ................ 72
6.2.2 From FinePixViewer installation to restart ....... 73
6.3 Installation on a Mac OS 8.6 to 9.2 .................... 77
6.3.1 Check the system software settings .......... 77
6.3.2 From FinePixViewer installation to restart .. 77
6.4 Installation on a Mac OS X ................................. 80
6.4.1 From FinePixViewer installation to restart .. 80
7 Camera Connection
7.1 Using the optional AC Power adapter ................ 83
7.2 Use at DSC mode ............................................... 84
4
System Expansion Options ................................ 101
Accessories Guide ............................................. 102
Notes on Using Your Camera Correctly ............. 104
Notes on the Power Supply ................................ 105
Applicable Batteries ...................................... 105
Notes on the Batteries .................................. 105
AC Power Adapter ........................................ 107
Notes on the xD-Picture Card ............................ 108
Warning Displays ............................................... 110
Troubleshooting .................................................. 113
Specifications ..................................................... 116
Explanation of Terms ......................................... 118
Safety Notes ....................................................... 119
IMPORTANT ...................................................... 123
5
6
7
8
5
Preface
■ Test Shots Prior to Photography
■ Notes on Electrical Interference
For particularly important photographs (such as weddings and
overseas trips), always take a test photograph and view the
image to make sure that the camera is functioning normally.
h Fuji Photo Film Co., Ltd. cannot accept liability for any
incidental losses (such as the cost of photography or the
loss of income from photography) incurred as a result of
faults with this product.
If the camera is to be used in hospitals or aircrafts, please
note that this camera may cause interference to other
equipment in the hospital or aircraft. For details, please
check with the applicable regulations.
■ Notes on Copyright
Images recorded using your digital camera system cannot be
used in ways that infringe copyright laws without the consent
of the owner, unless intended only for personal use. Note that
some restrictions apply to the photographing of stage
performances, entertainments and exhibits, even when
intended purely for personal use. Users are also asked to note
that the transfer of memory cards containing images or data
protected under copyright laws is only permissible within the
restrictions imposed by those copyright laws.
■ Liquid Crystal
6
Accessories and Attaching the Strap
If the LCD monitor or display panel is damaged, take particular
care with the liquid crystal in the monitor or panel. If any of the
following situations arise, take the urgent action indicated.
h If liquid crystal comes in contact with your skin
Wipe the area with a cloth and then wash thoroughly with
running water and soap.
h If liquid crystal gets into your eye
Flush the affected eye with clean water for at least
15 minutes and then seek medical assistance.
h If liquid crystal is swallowed
Flush your mouth thoroughly with water. Drink large
quantities of water and induce vomiting. Then seek
medical assistance.
■ Handling Your Digital Camera
Accessories
h16 MB, xD-Picture Card (1)
Supplied with:
• Anti-static case (1)
Attaching the Strap
1
0
2
0
This camera contains precision electronic components. To
ensure that images are recorded correctly, do not subject the
camera to impact or shock while an image is being recorded.
■ Trademark Information
h IBM PC/AT is a registered trademark of International
Business Machines Corp. of the U.S.
h iMac and Macintosh are registered trademarks of Apple
Computer, Inc.
h QuickTime and the QuickTime logo are trademarks used
under license. The QuickTime logo is registered in the
U.S. and other countries.
h Adobe Acrobat ® Reader ™ is a trademark of Adobe
Systems Incorporated of the U.S.
h Microsoft , Windows, the Windows logo and DirectX are
either trademarks, or registered trademarks of Microsoft
Corporation in the United States and/or other countries.
Windows is an abbreviated term referring to the Microsoft
Windows Operating System.
✽ The “Designed for Microsoft Windows XP” logo refers to
the camera and the driver only.
hxD-Picture Card and other company or product names are
trademarks or registered trademarks of the respective
companies.
■ Exif Print (Exif ver. 2.2)
Exif Print Format is a newly revised digital camera file format that
contains a variety of shooting information for optimal printing.
hLR6 AA-size alkaline Batteries (2)
hHand strap (1)
1Pass the loop of this cord on the end of the
strap through the strap mount.
2Then pass the other end of the strap through
the loop of the thin cord and pull the strap
tight.
hUSB Interface Set (1)
• CD-ROM: Software for FinePix SX (1)
• USB cable with Noise Suppression core (1)
hOwner’s Manual (this manual) (1)
7
Nomenclature
Mode Switch
✽ Refer to the pages in parentheses for information on using the camera features.
Still photography mode (P.21)
Viewfinder lamp (P.14)
Select this mode for still photography.
Playback mode (P.31)
Viewfinder (P.23)
This mode provides playback zoom and multi-frame
playback as well as normal single-frame playback.
You can also use this mode to erase frames, format
xD-Picture Card and specify DPOF settings.
LCD monitor
(P.23)
g button
(a) (b)
/ Zoom button
Movie mode (P.48)
Shutter button
BACK button (P.19)
MENU / OK button(P.19)
DISP button (P.19,30,32)
POWER switch(P.14)
Strap mount(P.7)
Flash (P.40)
Flash control sensor
Viewfinder window
Battery cover
(P.12,13)
(USB) socket
Tripod mount
Self-timer lamp
xD-Picture Card slot
(P.13)
(P.45)
Lens cover (P.14)
(P.84,87)
Battery compartment
Lens
8
DC IN 3V
(Power input)
socket (P.83)
9
1 Getting Ready
Nomenclature (Sample display)
Example of LCD Monitor Text Display: Still photography mode
Macro
Flash
Still photography mode
49
1M
AF
Zoom bar
1/ 1/2002
Date
Compatible batteries
EV(Exposure compensation)
White balance
Number of remaining shots
Quality mode
Battery level warning
Camera shake warning
AF warning
AF frame
Example of LCD Monitor Text Display: Playback mode
Playback mode
Protection
100ー0001
1/ 1/2002
Date
10
Playback frame number
Battery level warning
DPOF
LOADING THE BATTERIES AND xD-Picture Card
Use two AA-size alkaline batteries or two AAsize nickel-metal hydride (Ni-MH) batteries.
xD-Picture Card (sold separately)
DPC-16 (16MB)
DPC-64 (64MB)
DPC-32 (32MB)
DPC-128 (128MB)
◆ Notes on Handling Batteries ◆
h It is recommended that you use the same brand of
alkaline batteries as those supplied with the camera.
h Never use a battery when the Outer casing
outer casing is split or peeling as
this could result in a short-circuit
and cause major problems due
to battery fluid leakage or
overheating.
h Do not use different types of batteries or old and new
batteries together.
h You cannot use lithium, manganese or nickelcadmium (Ni-Cd) batteries.
h The operating lives of alkaline batteries vary between
brands and the life of batteries you purchase may be
shorter than the alkaline batteries provided with the
camera. Note also that due to the nature of alkaline
batteries, the time for which they can be used is
shorter in cold locations (at temperatures of +10°C
(+50°F) or below). Consequently, Ni-MH batteries are
recommended.
h Soil (fingerprints, etc) on the terminals of batteries can
greatly reduce the time for which the batteries provide
power.
h You will need the optional charger (➡ P.102) to
recharge Ni-MH batteries.
h See P.105 for notes on using batteries.
1
Front
Back
! Operation of this camera is only guaranteed when it
●
is used with FUJIFILM xD-Picture Card.
! Because xD-Picture Cards are small, they can be
●
accidentally swallowed by small children. Be sure to
store xD-Picture Cards out of the reach of small
children. If a child accidentally swallows an xD-Picture
Card, seek medical advice immediately.
! See P.108-109 for more information on xD-Picture
●
Card.
11
LOADING THE BATTERIES AND xD-Picture Card
1
0
2
0
3
0
4
0
Indicator
1
Indicator
1Slide the battery cover out to open it.
2Load the batteries correctly as shown.
◆ When you want to replace
the battery ◆
Check that the camera is switched off, open the
battery cover and then remove the battery.
3 Push the xD-Picture Card firmly into the
xD-Picture Card slot as far as it will go.
4 Close the battery cover.
◆ Replacing an xD-Picture Card ◆
When you push the xD-Picture Card into the slot
and then slowly remove your finger, the lock is
released and the xD-Picture Card is pushed out.
You can then pull the xD-Picture Card the rest of
the way out.
! If you open the battery cover while the camera is still
●
! Do not apply excessive force to the battery cover.
●
12
Do not open the battery cover while the camera
is still switched on. This could damage the xDPicture Card or corrupt the image files on the
xD-Picture Card .
! Take care not to drop the battery when opening
●
and closing the battery cover.
switched on, the camera is automatically switched
off to protect the xD-Picture Card.
! The xD-Picture Card will not slide fully into the slot if
●
it is inserted facing the wrong way. Be careful not to
apply undue force to the xD-Picture Card.
! When storing xD-Picture Card, always use the anti●
static case provided.
! Take care not to remove your finger too quickly
●
after the lock is released, as the card may
spring completely out of the slot.
13
SWITCHING ON AND OFF
1
SETTING THE DATE AND TIME
1
0
2
1
2
DATE/TIME
YYYY MM DD
DATE/TIME
NOT SET
2002 1 1
2002
1 1
12:00
OK SET
BACK NO
2
0
OK
When you slide the “POWER” switch sideways
to switch the camera on, the green viewfinder
lamp lights. To switch the camera off, slide the
“POWER” switch sideways again.
1Use the Mode switch to select the mode you
want to use.
2If you want to use the camera in Still
photography/Movie mode, open the lens cover.
If the “ ç ” warning message
appears on the LCD monitor, slide the lens
cover completely.
14
! Open and close the lens cover by fitting your finger
●
into the indentation in the cover.
! Take
●
care not to press on the lens when it is
extending or while you are taking a shot as this could
cause a camera fault.
1
0
1
AM
BACK
2
0
When you first switch the camera on, the date is
cleared. Press the “MENU/OK” button to set the
date and time.
1 Use “d” or “c” to select Year, Month, Day,
Hour or Minute.
2 Press “a” or “b” to set the number.
! To
●
! If
●
set the date and time later, press the “BACK”
button.
! If you do not set the date and time, this confirmation
●
screen will appear each time you switch the camera on.
you hold down “a” or “b”, the numbers change
continuously.
! When the time displayed passes “12:00”, the AM/PM
●
setting automatically switches.
15
SETTING THE DATE AND TIME
3
Changing the date and time
To change the date display format
YYYY MM DD
SET−UP
DATE/TIME
2002 10 29
8 40
8 40
OK
AM
BACK
POSTVIEW
POWER SAVE
USB MODE
DATE/TIME
OK
10
0
3
MM/DD/YYYY
ON
ON
DSC
SET
1/ 1/2002
12:00
OK
BACK
20
0
4
AM
BACK
1
0
◆ Checking the remaining battery charge ◆
Switch the camera on and check that no battery
level warning (Z or X) is displayed on the
LCD monitor. If no icon indicating the remaining
battery charge is displayed, the battery has
ample charge.
DATE/TIME
2
0
i Z Lit red:
Battery charge low. Replace or recharge the
battery as it will run out shortly.
i X Blinking red:
The battery is exhausted. The display will shortly
go blank and the camera will stop working.
Replace or recharge the battery.
1
! The above estimates are for the Still photography
●
modes. In Playback mode, the transition from “Z”
to “X” may take less time.
Once you have set the date and time, press the
“MENU/OK” button. Pressing the “MENU/OK”
button switches the camera to still photography
or Playback mode.
! You cannot set the seconds, but you can set the time
●
16
more accurately by pressing the “MENU/OK” button
when the time on your reference clock is at zero
seconds.
! If the camera is left for 30 minutes or longer with the
●
batteries removed and the AC power adapter
disconnected, the date and time settings may revert to
the factory default settings. If this occurs, reset the date
and time.
To change the date and time:
1 Press the “MENU/OK” button.
2 Use “d” or “c” to select “g” OPTION and
then use “a” or “b” to select “SET–UP”.
3 Press the “MENU/OK” button.
4 Select “DATE/TIME” and press “c”.
See P.15 for information on setting the date and
time.
1 Press “d” or “c” to select the date format.
2 Press “a” or “b” to set the format. Refer to
the table below for details of the settings.
Setting
Explanation
YYYY.MM.DD Displays the date in the “year.month. day” format.
◆ Power Save Function ◆
If the camera is not used for 2 minutes, this
function automatically switches it off.
When this function is enabled, the LCD monitor
switches off to conserve battery power if the
camera is not used in any way for 30 seconds
(See P.70 for details).
MM/DD/YYYY Displays the date in the “month/day/ year” format.
DD.MM.YYYY Displays the date in the “day.month. year” format.
17
2 Basic
Photography
SELECTING THE LANGUAGE
1
10
0
3
2
1
0
2
0
0
BASIC OPERATION GUIDE
DISP button
You can use this button to
select the LCD monitor display
mode.
2
0
When shooting : Switches
the LCD monitor on and off
or displays the framing guides.
SET−UP
OPTION
SET−UP
LCD BRIGHTNESS
AUTO
MANUAL
LCD
BEEP♪
LANGUAGE
RESET ALL
OK
ON
LOW
ENGLISH
OK
During playback : Switches
text display on and off or selects
multi-frame playback.
1The “SET–UP” screen appears. Use “a” or
“b” to select “LANGUAGE”.
2Use “c” to select “ENGLISH”, “FRANCAIS” or
“DEUTSCH”. You can cycle through the
language settings by pressing “c”.
! The screens in this manual are shown in English.
●
! See P.68 for more information on the “g” OPTION
●
menu.
Slide this switch to turn the
camera on and off.
0 Switching between still
photography,playback
and movies
Still photography
For recording still images.
Playback
For playing back recorded
data.
2
Movie
For recording movies.
MENU/OK button
Displays the menu screen
when you are shooting or
playing back images. You also
press this button to confirm a
menu selection.
0
18
POWER switch
BACK
0
1Press the “MENU/OK” button to display the
menu screen.
2Use “a”, “b”, “d” or “c” to select “SET–UP”
from the “g” OPTION menu.
3Press the “MENU/OK” button.
0
BACK button
Press this button to stop a
procedure midway through.
0
Main actions performed
by a, b, dand c
gbutton :
Change frame in playback.
fbutton :
Digital zoom, Playback
zoom.
19
BASIC OPERATION GUIDE
Q MODE
1
●Using the Menus
TAKING PICTURES (A AUTO MODE)
1
0
2
0
2
1Display the menu.
Press the “MENU/OK” button.
2Select a menu option.
3Select a setting.
Press the “d” or “c”.
Press the “a” or “b”.
3
0
QUALITY
2M F
2M N
1M
0 3M
QUALITY
2M F
2M N
1M
0 3M
25
39
49
122
25
39
49
122
4Confirm your selection.
Press the “MENU/OK” button.
Press this button to stop
a procedure midway
through.
20
2
In the Owner's Manual,black triangles
are used to indicate up,down (a,b )
and left, right (d,c) respectively.
◆ Displaying the On-screen Help ◆
Help messages are displayed at the bottom of
the screen to show you the next step to take.
Press the button indicated.
DISP ZOOM
Press the “DISP” button
to use the zoom.
DISP ZOOM
1Set the Mode switch to “Q”.
2Open the lens cover. If the “ ç ”
warning message appears on the LCD
monitor, slide the lens cover completely.
3Slide the “POWER” switch sideways to switch
the camera on.
To take pictures using the LCD monitor, press
the “DISP” button to switch the LCD monitor on.
h Focal range: Approx. 80 cm (2.6 ft.) to infinity
! If
●
the “Ω ”, “∂ ”, “≈ ” or
˙” message appears, see P.110.
“
Loop the strap over your wrist, brace your
elbows firmly against your body and hold the
camera with both hands.
! For subjects closer than 80 cm (2.6 ft.), use Macro
●
photography (➡P.43).
! To minimize power consumption, you should use the
●
viewfinder (switch the LCD monitor off) to take pictures.
! Use a tripod to avoid camera shake, particularly for
●
shots is dark situations when the flash is set to
Suppressed Flash mode (➡P.40).
21
Q MODE
TAKING PICTURES (A AUTO MODE)
3
4
6
5
1M
AF frame
49
1M
LCD monitor
2
Ensure that your fingers or the camera strap do
not obscure the lens or flash control sensor.
Zoom bar
! There may be some unevenness in the brightness at
●
22
the lower edge of the LCD monitor. This is normal
and does not indicate a fault. This does not affect
the photographed image.
! Check that the lens is clean. If it is dirty, clean the
●
lens as described on P.104.
! If you use the flash in very dusty conditions or when
●
it is snowing, white dots may appear in the image
due to the flash reflecting off the dust particles or
snowflakes. Try taking the shot with the flash mode
set to Suppressed Flash.
AF frame
To zoom in on the subject, press “a” (} TELE).
To zoom out, press “b” ({ WIDE). A “zoom
bar” appears on the LCD monitor when you
zoom in or out.
● Optical zoom focal length (35mm camera
equivalent)
Approx. 38 mm-114 mm (1.5 in. to 4.5 in.)
Maximum zoom scale: 3×
Using the viewfinder or LCD monitor, frame your
shot so that the subject fills the entire AF (Auto
Focus) frame.
! Zooming
●
! If your subject is not in the center of the picture, use
●
stops briefly when the camera switches
between optical zoom and digital zoom (➡P.29).
Viewfinder
AF/AE lock to take the picture(➡P.27).
When you are using the viewfinder to take a
picture at a distance of 0.8 m to 1.5 m (2.6 ft. to
4.9 ft.), only the shaded area in the figure is
photographed.
! To
●
frame your shot precisely, you should take the
picture using the LCD monitor.
! In some conditions it may be difficult to see your
●
subject clearly on the LCD monitor, such as in sunny
weather outdoors or when you are shooting dimly lit
scenes. In such situations, use the viewfinder to take
the shot.
! The image shown on the LCD monitor before you
●
take the shot may differ in its brightness, color, etc.
from the image actually recorded. If necessary, play
back the recorded image to check it (➡P.31).
23
Q MODE
TAKING PICTURES (A AUTO MODE)
7
8
■ Viewfinder Lamp Display
Beep
✽ When the LCD monitor is switched on, more detailed warning messages
are displayed (➡P.110-112).
Display
To take the picture, press the shutter button
down fully without lifting your finger off it. The
camera beeps and takes the picture, and the
data is then recorded.
! When you press the shutter button, there is a very
●
short delay before the picture is actually taken.
! Since the amount of image data recorded is not fixed
●
Press the shutter button down halfway. The
camera is focused when the AF frame on the
LCD monitor shrinks and the green viewfinder
lamp stops flashing and stays lit.
! If you press the shutter button down fully in one motion,
●
the shot is taken without the AF frame changing.
! The viewfinder lamp flashes orange while the flash is
●
24
charging. If the LCD monitor is switched on, the
screen may go dark for a moment. This is normal
and does not indicate a fault.
! The flash charging time may increase when the
●
battery charge decreases.
and varies depending on the subject (level of image
detail, etc.), the number of available shots may not
decrease after the image is recorded, or may
decrease by 2.
! See P.110-112 for information on the warning
●
displays.
The viewfinder lamp glows orange while the
image is being recorded and no pictures can be
taken. Also, do not switch the camera off or
open the battery cover during image recording.
Opening the cover during image recording could
corrupt the image files.
Status
Lit green
Ready to shoot.
Blinking green
AF/AE in progress, camera shake warning or AF warning (Ready to shoot).
Blinking green and Recording to xD-Picture Card (Ready to shoot).
orange alternately
Lit orange
Recording to xD-Picture Card (Not ready).
Blinking orange
Flash charging. PC communication in progress (Flash will not fire).
Blinking red
h xD-Picture Card Warnings
No card loaded, card not formatted, incorrect format, card full, xD-Picture Card error.
h Lens operation error.
2
◆ Subjects Not Suitable for Autofocus ◆
Though the FinePix 2650 uses an accurate autofocus mechanism, it may have difficulty focusing or not be able to
focus at all for the types of subject and situation listed below. In such cases, the image may be out of focus.
h Very shiny subjects such as a mirror or car body.
h Subjects photographed through glass.
h Subjects that do not reflect well, such as hair or fur.
h Subjects with no substance, such as smoke or flames.
h When the subject is dark.
h When there is very little contrast between the subject
and the background (such as white walls or subjects
dressed in the same color as the background).
h Subjects moving at high speed.
h When something other than your subject is close to the
AF frame, has contrasting areas of light and dark and is
either closer or further away than your subject (as when
you photograph someone against a background with
strongly contrasting elements).
For subjects of this type, use AF/AE lock (➡P.27).
25
Q MODE
TAKING PICTURES (A AUTO MODE)
Q MODE
1
Number of Available Frames
49
1M
The number of available shots is displayed on
the LCD monitor.
! See P.39 for information on changing the quality.
●
! The default quality setting “y ” set at shipment
●
USING AF/AE LOCK
49
1M
2
49
1M
is
1M.
2
■ Standard number of shots per xD-Picture Card
Because the amount of data recorded varies depending on the subject, the number of available shots may not
decrease when recording ends, or may decrease by 2 frames. The discrepancy between the standard number of
available shots and the actual number of available shots increases in proportion to the capacity of the xD-Picture Card.
Quality mode
2M • F
2M • N
1600 × 1200
Number of recorded pixels
1M
0.3M
1280 × 960
640 × 480
Image Data Size
Approx. 620 KB
Approx. 390 KB
Approx. 320 KB
Approx. 130 KB
DPC-16 (16 MB)
25
39
49
122
DPC-32 (32 MB)
50
79
99
247
DPC-64 (64 MB)
101
159
198
497
DPC-128 (128 MB)
204
319
398
997
✽ Number of available shots displayed on the camera for a new xD-Picture Card formatted in the camera.
26
In a shot with this type of composition, the
subjects (two people in this case) are not in the
AF frame. If the shot is taken at this point, the
subjects will not be in focus.
Move the camera slightly so that one of the
subjects in the AF frame.
Continued over page...
◆ AF (Autofocus)/AE (Auto exposure) Lock ◆
On the FinePix 2650, when you press the shutter button down half way, the focus and exposure settings
are fixed (AF/AE lock). If you want to focus on a subject that is off to one side of the image or if you want
to set the exposure before you compose the final shot, lock the AF and AE settings and then compose
and shoot your picture to get the best results.
27
Q MODE
Q MODE
USING AF/AE LOCK
3
4
USING THE ZOOM
Zoom bar display
Digital zoom
Beep
Optical zoom
1M
Press “a” to zoom in and make your subject
larger. Press “b” when you want to zoom out
and shoot a wider area. If you use the LCD
monitor to take pictures, you can continue
zooming with the digital zoom after the optical
zoom finishes.
Without moving the camera, press the shutter
button down halfway (AF/AE lock). Check that
the AF frame on the LCD monitor has shrunk
and the green viewfinder lamp has stopped
flashing and is now lit.
Continue to hold the shutter button down
halfway. Move the camera back to the original
image and then fully press down on the shutter
button.
! You can reapply the AF/AE lock as many times as
●
you like before releasing the shutter.
28
! The AF/AE lock operates in all photography modes
●
and can be used to ensure excellent results.
Mode
Max.
Quality Digital zoom focal distance✽ Zoom
Scale
2M
Cannot be used
Still
1M Equivalent to approx. 114 mm-146 mm Max. 1.3×
photography
0.3M Equivalent to approx. 114 mm-285 mm Max. 2.5×
1M Equivalent to approx. 38 mm- 48 mm Max. 1.3×
E Macro
0.3M Equivalent to approx. 38 mm- 95 mm Max. 2.5×
! See
●
✽ 35 mm camera equivalent
P.39 for information on changing the quality
setting.
03M
Macro
2
The position of the “■” on the zoom bar indicates
the current zoom setting.
hIf the “■” is above the dividing line, the digital
zoom is being used. If it is below the line, the
optical zoom is being used.
hPress “a” or “b” to move the “■” up and down.
hWhen you switch between digital zoom and
optical zoom, the “ ■ ” stops moving briefly.
Press the button for the same direction again
to start the “■” moving and switch the zoom
setting.
! If
●
the image goes out of focus when you use the
zoom, press the shutter button down halfway to
refocus.
! The optical zoom is equivalent to approximately
●
38 mm-114 mm on a 35 mm camera.
29
Q MODE
FRAMING GUIDELINE FUNCTION
w MODE
Scene
VIEWING YOUR IMAGES (PLAYBACK)
1
0
2
0
Fast Forwarding Images
Use this frame when you want to position your
main subject in the center of the frame or when
you want to align your shot with the horizon.
This feature provides a clear guide to the
subject size and the overall balance of the shot
so that you get exactly the shot you want.
2
LCD monitor ON
49
1M
Framing guideline
displayed
1Set the Mode switch to “w”.
2You can “d” or “c” to move forward and
backward respectively through your images.
LCD monitor OFF
100−0009
Playback frame
number
10/29/2002
You can select the framing guide function in “Q”
Still photography mode. The mode shown on the
LCD monitor switches each time you press the
“DISP” button. Press the “DISP” button to
display the framing guideline.
! The framing guideline is not recorded on the image.
●
! The lines in the scene frame roughly divide the
●
30
recorded pixels into three parts horizontally and
vertically. When the image is printed, the resulting
print may be shifted slightly from the scene frame.
◆ Important ◆
Always use the AF/AE lock to compose your
picture.
Failing to use the AF/AE lock may result in the
image being out of focus.
! When
●
you set the Mode switch to “ w ”, the last
image shot is displayed.
During playback, you can skip backwards or forwards through
the images (the frame number increases or decreases) by
holding down “d” or “c” for approximately 1 second.
The displayed image does not change, but a progress bar
indicates the approximate playback location on the xD-Picture
Card.
◆ Still images that can be viewed ◆
You can use this camera to view still images recorded on the FinePix 2650 or still images (excluding
some uncompressed images) recorded on a FUJIFILM digital camera that supports xD-Picture Cards.
31
w MODE
1
MULTI-FRAME PLAYBACK
Text displayed
2
w MODE
1
0
2
0
PLAYBACK ZOOM
1
2
10
0
3
2
0
No text displayed
Multi-frame
playback
2
100−0009
In playback mode, the display shown on the
LCD monitor switches each time you press the
“DISP” button. Press the “DISP” button until the
multi-frame playback screen (9 frames) appears.
You cannot display text during multi-frame
playback.
! You cannot use multi-frame playback while a menu
●
32
is displayed.
zoom cannot be used with multi-frame
playback.
! Playback
●
Zoom bar
10/29/2002
1 Select a frame by using “d”, “c”, “a” or “b”
to move the cursor (the orange box) to the
desired frame. Press the “a” or “b” several
times to switch to the previous page or the
next page.
2 You can enlarge the selected image by
pressing the “DISP” button again.
DISP PANNING
Pressing “a ” or “b ” during single-frame
playback zooms in (enlarges) or out on a still
image. When you use this function, a zoom bar
is displayed.
hZoom scales:
2M 1600 ×1200 pixel images: Max 10×
1M 1280 × 960 pixel images: Max 8×
0.3M 640 × 480 pixel images: Max 4×
! Pressing “d” or “c” during zooming cancels zooming
●
and moves to the next image.
! Multi-frame playback cannot be used with Playback zoom.
●
DISP ZOOM
After you have zoomed in on your image,
1Press the “DISP” button.
2Use “a”, “b”, “d” or “c” to zoom in on different
parts of the image.
3Press the “DISP” button again to revert to
zoomed display.
! You may not be able to use playback zoom for some
●
images shot on other camera models.
! Press the “BACK” button to return to normal unscaled
●
display.
This is useful for such things as checking the focus
after you take a shot.
33
w MODE
1
ERASING SINGLE FRAME
1
0
2
0
2
ERASE
3
4
FORMAT
ALL FRAMES
FRAME
BACK
ERASE
FRAME
FORMAT
ALL FRAMES
FRAME
BACK
1 Set the Mode switch to “w”.
2 Press the “MENU/OK” button to display the
Menu screen on the LCD monitor.
34
Note that mistakenly erased images cannot be
recovered. You should copy important files that
you do not want to be erased to your computer
or other media.
ERASE OK?
OK YES
BACK NO
Select “FRAME” in the “p” ERASE menu and
press the “MENU/OK” button.
See P.54 for more information on “ALL FRAMES”
and “FORMAT”.
2
100−0049
Pressing the “MENU/OK” button erases the
frame (individual file) displayed. When erasing is
complete, the next image appears and the
“§” message is displayed.
Press “d” or “c” to view the frame (individual
file) you want to erase.
! Press the “BACK” button to cancel frame erasing.
●
To erase another frame, repeat steps
3 and 4 .
35
Features
3 Advanced
Photography
Q MODE
SELECTING A AUTO OR S MANUAL
1
2
10
0
3
2
0
PHOTOGRAPHY MENU OPERATION
1
10
0
3
2
0
2
49
1M
OPTION
Set the Mode switch to “Q”.
! See P.48 for information on shooting movies.
●
SET−UP
LCD BRIGHTNESS
AUTO
MANUAL
Q AUTO
This is the easiest mode for taking pictures and
can be used in a wide range of conditions.
Q MANUAL
This mode allows you to specify your own
brightness and white balance settings.
36
1Press the “MENU/OK” button to display the
menu.
2Use “d” or “c” to select the menu item and
“a” or “b” to change the setting.
3Press the “MENU/OK” button to confirm the
selection.
When you validate the settings, the respective
icons appear at the top of the screen.
3
1Press the “MENU/OK” button to display the
menu.
2Use “d” or “c” to select “g” OPTION and
then use “a” or “b” to select “Q AUTO” or
“Q MANUAL”.
3Press the “MENU/OK” button to confirm the
selection.
! The
●
settings available in the menu screen differ
depending on the still photography mode.
37
PHOTOGRAPHY AND MOVIE MENU OPTIONS
PHOTOGRAPHY MENU
This section gives a quick overview of the various functions you can use when the mode switch is set
to “Q” or “T”.
Mode
Sample LCD monitor display
QUALITY
A AUTO
2M・F 25
2M・N 39
49
1M
03M
122
EV
S MANUAL
+0 3
0
−0 3
−0 6
Accessible menu settings
Factory default
Explanation
y
c
E
=
g
QUALITY
FLASH
MACRO
SELF-TIMER
OPTION
1M
AUTO
OFF
OFF
–
P.39
P.40
P.43
P.44
P.68
y
c
E
a
d
g
QUALITY
FLASH
MACRO
WHITE BALANCE
EV
OPTION
1M
AUTO
OFF
AUTO
0
–
P.39
P.40
P.43
P.46
P.47
P.68
320 × 240
–
P.51
P.68
y SETTING THE QUALITY
Use
QUALITY
Factory default
2M・F 25
2M・N 39
49
1M
03M
122
Printing
Number of remaining shots
Internet
✽ Displaying the menus (➡P.37)
Quality
2M • F (1600 × 1200)
2M • N (1600 × 1200)
1M
(1280 × 960)
0.3M ( 640 × 480)
<Examples>
hFor printing on A5 paper → 2M • F, 2M • N
This mode can be selected in the
“ A ”, “ S ” still photography
modes.
You can choose from 4 settings. Use the table on
the right as a guide for selecting the best setting
for the shot you want to take.
✽ Select “2M • F” (FINE) for better image quality and
“2M • N” (NORMAL) to increase the number of
available shots.
In most cases, the “2M • N” setting provides more
than adequate image quality.
3
hFor printing on A6 (postcard) paper → 1M
hFor an image attached to E-mail or used on a
website → 0.3M
QUALITY
T MOVIE
38
y QUALITY
g OPTION
! The numbers to the right of each setting show the
●
number of available shots.
you change the quality, the number of
available shots also changes.
! When
●
39
PHOTOGRAPHY MENU
c FLASH
✽ Displaying the menus (➡P.37)
FLASH
Factory default
AUTO
This mode can be selected in the
“ A ”, “ S ” still photography
modes.
Use the flash mode that best suits your shot.
h 5 modes: “AUTO”, “n”, “c”, “b” and “v”
h Effective flash range (in “A AUTO” mode):
Wide-angle: Approx. 0.2 m to 3.0 m (0.6 ft. to 9.8 ft.)
Telephoto: Approx. 0.8 m to 3.0 m (2.6 ft. to 9.8 ft.)
! If you use the flash in very dusty conditions or when it is
●
40
snowing, white dots may appear in the image due to the flash
reflecting off the dust particles or snowflakes. Try taking the shot
with the flash mode set to Suppressed Flash.
! The flash charging time may increase if the charge remaining
●
in the batteries is low.
! When you take a shot using the flash, you may see the video
●
image disappear and the screen go dark as the flash charges.
The viewfinder lamp flashes orange while the flash is
charging.
AUTO Auto Flash Mode
Use this mode for ordinary photography. The
flash fires automatically as required by the
shooting conditions.
n Red-Eye Reduction
Use this mode to ensure that the subject’s eyes
appear natural when photographing people in
low-light conditions. The flash fires automatically
as required by the photography conditions.
The flash fires a pre-flash just before the picture
is taken and then fires again to take the actual
picture.
c Forced Flash
Use this mode to photograph backlit scenes,
such as a subject against a window or in the
shade of a tree, or to obtain the correct colors
when you are shooting under lighting such as
fluorescent tubes. In this mode, the flash fires in
bright as well as dark conditions.
3
◆ Red-Eye Effect ◆
When you use the flash to photograph people in low-light conditions, their eyes sometimes appear red in
the picture. This is caused by the light of the flash reflecting off the inside of the eye. Use Red-Eye
Reduction flash to effectively minimize the likelihood of the red-eye effect.
Take the following measures also to make Red-Eye Reduction more effective:
● Get the subjects to look at the camera.
● Get as close as possible to the subjects.
41
PHOTOGRAPHY MENU
c FLASH
PHOTOGRAPHY MENU
E MACRO (CLOSE-UP) PHOTOGRAPHY ✽ Displaying the menus (➡P.37)
MACRO
ON
OFF
Factory default
b Suppressed Flash
42
v Slow Synchro
Use this mode for photography using indoor
lighting, for shots taken through glass, and for
photography in venues such as theaters or at
indoor sporting events where the distance is too
great for the flash to be effective. When you use
Suppressed Flash, the Automatic White Balance
function (➡P.118) operates so that natural colors
are captured along with the ambience of the
available light.
This is a flash mode that uses a slow shutter
speed. This allows you to take pictures of people
at night that clearly show both your subjects and
the night time backdrop.
! If you are shooting in Suppressed Flash mode in dark
●
! The
●
conditions, use a tripod to prevent camera shake.
! See P.110 for information on the camera shake
●
warning.
image may be overexposed when you shoot
bright scenes.
! Because a slow shutter speed is used, a tripod
●
should be used to prevent camera shake.
✽ Displaying the menus (➡P.37)
Selecting Macro mode specifies the following
camera settings:
h The lens is fixed to the wide-angle zoom
setting and only digital zooming is available.
h The LCD monitor is fixed to the ON setting.
h Switching the camera off cancels Macro
mode.
This mode can be selected in the
“ A ”, “ S ” still photography
modes.
3
Use Macro mode for close-up shots.
h Focal range: Approx. 10 cm to 80 cm (3.9 in.
to 2.6 ft.)
(Approx. 20 cm to 80 cm (0.6 ft. to 2.6 ft.) when
the flash is used)
● Digital zoom focal distance (35 mm camera
equivalent)
1M: Equivalent to approx. 38 mm-48 mm
(1.3×)
0.3M: Equivalent to approx. 38 mm-95 mm
(2.5×)
! When
●
shooting in dark conditions, use a tripod to
prevent camera shake.
If you use the viewfinder to take pictures in
Macro mode, there is a discrepancy between
what you see and what the camera actually
photographs due to the difference in the
positions of the lens and the viewfinder window.
For this reason, you should always use the LCD
monitor when shooting in Macro mode.
43
PHOTOGRAPHY MENU
1
Factory
default
= SELF-TIMER PHOTOGRAPHY ✽ Displaying the menus (➡P.37)
2
SELF−TIMER
49
1M
1
0
ON
OFF
7
3
0
Beep
This mode can be selected in the
“A” still photography mode.
When you set the self-timer to “ON”, “=” appears on
the LCD monitor.
In this mode, a timer runs for roughly 10 seconds
before the shutter is released. Use this mode for shots
such as photographs of yourself.
44
4
49
1M
2
0
! The
●
3
self-timer is automatically cancelled in the following
situations:
• When shooting ends
• When you switch to “A” or “S” mode
• When the mode switch setting is changed
• When the camera is switched off
! You can also use the AF/AE lock (➡P.27).
●
! Be careful not to stand in front of the camera when you
●
press the shutter button as this can cause focusing or
exposure metering errors.
The self timer lamp lights for 5 seconds and then
starts flashing. 5 seconds later the camera emits
a short beep and takes the picture.
Until the picture is taken, a countdown appears
on the LCD monitor.
Self-timer mode is automatically cancelled after
each shot.
3
1 Position the AF frame over your subject.
2 Press the shutter button down half way to set
the focus.
3 Without releasing the shutter button, press it
down fully. The self-timer then starts running.
! To
●
stop the self-timer once it has started running,
press the “BACK” button.
45
PHOTOGRAPHY MENU
a WHITE BALANCE (SELECTING THE LIGHT SOURCE)
WHITE BALANCE
Factory default
AUTO
✽ Selecting A/S (➡P.36)
✽ Displaying the menus (➡P.37)
PHOTOGRAPHY MENU
EV
Factory default
+0 3
0
−0 3
−0 6
lamps
0 : Shooting under “Warm White” fluorescent
This mode can be selected in the
“S” still photography mode.
Change the white balance setting when you
want to take a picture with the white balance
fixed for the surroundings and lighting when the
picture is taken.
In Auto mode, the correct white balance may not
be obtained for subjects such as close-ups of
people’s faces and shots taken under a special
light source. In such situations, select the correct
white balance for the light source. See P.118 for
information on the white balance.
46
lamps
- : Shooting under “Cool White” fluorescent
lamps
8 : Shooting in incandescent light
✽ The white balance setting is ignored when the flash is
used. To achieve the desired effect in your shot, set
the flash to Suppressed Flash mode (➡P.42).
✽ Selecting A/S (➡P.36)
✽ Displaying the menus (➡P.37)
◆ Subjects for Which Exposure
AUTO: Automatic adjustment
(Shooting to show the ambience of the
light source)
6 : Shooting outdoors in fine weather
7 : Shooting in shade
9 : Shooting under “Daylight” fluorescent
d EV (EXPOSURE COMPENSATION)
This mode can be selected in the
“S” still photography mode.
Use the Brightness setting to obtain the optimum
image brightness (exposure) when the subject is
much brighter or darker than the background.
hCorrection range: –2.1 EV to +1.5 EV
(13 steps in 0.3 EV increments)
See P.118 for information on EV.
Adjustment is Particularly Effective ◆
Guide to using + (positive) compensation
h Copying of printed text (black characters on
white paper) (+1.5 EV)
h Backlit portraits (+0.6 EV to +1.5 EV)
h Very bright scenes (such as snowfields) and
highly reflective subjects (+0.9 EV)
h Shots made up predominantly of sky
(+0.9 EV)
Guide to using – (negative) compensation
3
h Spotlit subjects, particularly against dark
backgrounds (–0.6 EV)
h Copying of printed text (white characters on
black paper) (–0.6 EV)
h Scenes with low reflectivity, such as shots of
pine trees or dark foliage (–0.6 EV)
! The
●
Brightness setting is disabled in the following
situations:
i When the flash is used in Auto or Red-Eye
Reduction mode.
i When dark scenes are shot in Forced Flash mode.
47
T MODE
T MOVIE (VIDEO)
1
2
4
3
20s
STANDBY
Set the Mode switch to “T”.
This mode allows you to shoot movies up to 20
seconds (at the # setting) or 80 seconds (at the
$ setting) without sound. (See P.51 for
information on quality settings.)
hMovie format: Motion JPEG (➡P.118)
# (320 × 240 pixels)
$ (160 × 120 pixels)
selectable
10 frames per second
Without sound
! Select Macro mode for close-up shots (➡P.43).
●
! Depending on the available space on the xD-Picture
●
48
Card, the available shooting time per movie may be
shorter.
! You cannot switch the LCD monitor off in this mode.
●
! It may not be possible to play back your movie on
●
other cameras.
20s
The available shooting time and the “œ”
message are shown on the LCD monitor.
■ xD-Picture Card standard shooting time
Quality mode
xD-Picture Card
Capacity
#
DPC-16 (16 MB)
Approx. 94 sec.
Approx. 5.0 min.
DPC-32 (32 MB)
Approx. 191 sec.
Approx. 10.1 min.
DPC-64 (64 MB)
Approx. 6.4 min.
Approx. 20.2 min.
DPC-128 (128 MB)
Approx. 12.9 min.
Approx. 40.6 min.
$
✽ The available shooting time displayed on the camera
for a new xD-Picture Card formatted in the camera.
STANDBY
When you press the shutter button, the camera
starts shooting.
Zoom bar
! You do not need to hold down the shutter button.
●
! The focus is fixed at 80 cm (2.6 ft.) to infinity.
●
! The white balance is fixed during shooting, but the
●
During movie shooting, the lens is fixed at the
wide-angle zoom setting and only the digital
zoom can be used.
Use “a” or “b” to zoom in and out. A zooming
bar is displayed on the LCD monitor.
The focal distances and maximum zoom ratios
for the digital zoom are shown below.
hDigital zoom focal distance (35 mm camera
equivalent)
Approx. 38 mm to 95 mm
Max. zoom scale: 2.5×
3
exposure varies automatically to suit the scene being
shot.
! The image shown on the LCD monitor before you
●
take the shot may differ in its brightness, color, etc.
from the image shown on the monitor during movie
recording.
The white balance is set automatically when you
press the shutter button.
Continued on next page...
49
T MODE
5
T MOVIE (VIDEO)
REC
19s
Quality settings for movies
6
1
1
0
2
QUALITY
Factory default
STORING
During shooting, “hREC” appears on the LCD
monitor with a counter showing the remaining
time displayed in the top-right corner.
50
automatically stops and the movie is stored on the
xD-Picture Card.
3
0
3
1
0
If you press the shutter button during shooting,
shooting ends and the movie is stored on the
xD-Picture Card.
! Once the remaining time runs out, movie recording
●
2
0
! If
●
you end shooting immediately after you start
shooting, only 1 second of movie is shot.
1 Set the Mode switch to “T”.
2 Press the “MENU/OK” button to display the
menu screen.
3 Press “d” or “c” to select “y” QUALITY.
You can select 2 levels of quality. For better
image quality, select “# ”, and for longer
photography time, select “$”.
2
0
1 Use “a” or “b” to change the quality setting.
2 Press the “MENU/OK” button to confirm the
selection.
Movie Size
Maximum shooting time
#
320 × 240
20 sec.
$
160 × 120
80 sec.
51
4 Advanced
Features Playback
1
w MODE
PLAYING BACK MOVIES
1
0
2
0
2
1
0
13s
PLAY
1Set the Mode switch to “w”.
2Use “d” or “c” to select the movie file.
2
0
■ Playing Back Movies
Control
Description
Playback
The movie automatically stops when playback ends.
Pause/Resume
Pauses the movie during playback.
Press this button again to resume playback.
Stop
Stops playback.
✽ Press “d” or “c” while movie playback is stopped to go back
to the previous file or advance to the next file respectively.
Fast forward/Rewind
Press these during playback to skip forwards or backwards
through the movie.
STOP
PAUSE
1Press “b ({)” to play the movie.
2The LCD monitor shows the playback time
and a playback progress bar.
Rewind
Forward
Skip playback
When paused
! Movies
●
cannot be played back using multi-frame
playback. Use the “DISP” button to revert to normal
playback.
52
Movies are displayed somewhat smaller than
still images.
4
i Each time you press “d ” or “ c ” when the movie is
paused, the movie advances or goes back one frame.
i Hold down the button to move through the frames
quickly.
◆ Playing back movie files ◆
! If
●
the subject of the movie is very bright, white
streaks may appear on the image during playback.
This is normal and is not a fault.
i This camera may not be able to play back movie files (10 fps) that were recorded on a camera other than FinePix 2650.
i To play back movie files on a computer, save the movie file on the xD-Picture Card to the computer’s hard disk and then
play back the saved file.
i Movie files contain large amounts of data. Depending on the performance of the computer, movies may not run
smoothly if the computer cannot process the images quickly enough.
53
PLAYBACK MENU
1
p ERASING SINGLE • ALL FRAMES/FORMATTING
1
0
2
0
2
ERASE
FORMAT
ALL FRAMES
FRAME
BACK
1Set the Mode switch to “w”.
2Press the “MENU/OK” button to view the
menu screen.
54
FORMAT
ERASE
Erases all the files. Because
formatting also erases protected files,
check carefully before formatting a
card and copy any files that you want
to keep onto another media, such as
your hard disk.
FORMAT
ALL FRAMES
FRAME
BACK
1
0
Use “d” or “c” to select “p” ERASE.
Note that mistakenly erased images cannot be
recovered. You should copy important files that
you do not want to be erased to your computer
or another media.
3
2
0
1Use “a” or “b” to select “FORMAT”, “ALL
FRAMES” or “FRAME”.
2Press the “MENU/OK” button to confirm the
selection.
ALL FRAMES
Erases all unprotected files.
You should copy important files that
you do not want to be erased to your
computer or another media.
4
FRAME
Erases only the selected file.
BACK
Returns to playback without erasing
any files.
Continued on next page...
55
PLAYBACK MENU
p ERASING SINGLE • ALL FRAMES/FORMATTING
FRAME
ALL FRAMES
FORMAT
◆ To stop the procedure mid-way ◆
100−0009
ALL FRAMES
ERASE ALL
OK?
IT MAY
TAKE A WHILE OK YES
BACK NO
FRAME
ERASE OK?
OK YES
BACK NO
FORMAT
FORMAT OK?
ALL FRAMES
ERASE
ALL DATA
OK YES
BACK NO
BACK CANCEL
1
0
2
0
4
When you want to cancel the “Erase all frames”
procedure, press the “BACK” button.
1Use “d” or “c” to select the file to be erased.
2Press the “MENU/OK” button to erase the
currently displayed file.
To erase another image, repeat steps 1 and 2.
When you have finished erasing images, press
the “BACK” button.
56
! The file for which “ˆ” was displayed
●
cannot be erased. Remove the protection.
Pressing the “MENU/OK” button erases all the
files and initializes the xD-Picture Card.
Formatting also erases protected files.
Pressing the “MENU/OK” button erases all the
unprotected files.
©
ø
If the “
”
“
” message appears,
press the “MENU/OK” button once more to erase
the image.
! Even
●
if you stop the procedure immediately,
some files will be erased.
! If the “∂”, “ƒ”, “å” or
●
˙
” message appears, refer to
“
P.110, 111 before formatting the xD-Picture Card
and take the appropriate measures.
57
PLAYBACK MENU k
1
1
0
PROTECTING IMAGES FRAME/ALL
2
0
2
PROTECT
FRAME SET/RESET
3
UNPROTECT ALL
PROTECT
Removes the protection from all the
files.
FRAME SET/RESET
PROTECT ALL
Protects all the files.
1Set the Mode switch to “w”.
2Press the “MENU/OK” button to view the
menu screen.
1
0
2
0
FRAME SET/RESET
Protects or unprotects only the
selected file.
4
Use “d” or “c” to select “k” PROTECT.
! Multi-frame
●
playback is an easy way to select
images to be protected (➡P.32).
58
Protection is a setting that prevents images from
being accidentally erased. However, “FORMAT”
erases all images, regardless of protection
setting (➡ P.57).
1Press “a” or “b” to select “UNPROTECT ALL”,
“PROTECT ALL” or “FRAME SET/RESET”.
2Press the “MENU/OK” button to confirm the
selection.
Continued on next page...
59
PLAYBACK MENU
k
PROTECTING IMAGES FRAME/ALL
FRAME SET/RESET
PROTECT ALL
1
2
FRAME SET/RESET
FRAME SET/RESET
UNPROTECT
OK?
PROTECT OK?
OK
1
0
BACK
OK
BACK
PROTECT ALL
PROTECT ALL
OK?
IT MAY
TAKE A WHILE
OK
BACK
100−0009
UNPROTECT ALL
UNPROTECT
ALL OK?
IT MAY
TAKE A WHILE
OK
BACK
2
0
1 Press “d ” or “c ” to select the file to be
protected.
2 Press the “MENU/OK” button to protect the
file currently displayed.
To protect another file, repeat steps 1 and 2.
To finish protecting files, press the “BACK”
button.
60
UNPROTECT ALL
4
To remove the protection, press the “MENU/OK”
button.
Press the “MENU/OK” button to protect all the
files.
Press the “MENU/OK” button to unprotect all the
files.
◆ To stop the procedure mid-way ◆
100−0009
PROTECT ALL
BACK CANCEL
If the photographed images are very large, protecting or unprotecting all the
frames may take some time.
If you want to shoot a picture or a movie during the procedure, press the “BACK”
button. To then return to protecting or unprotecting all the frames, start the
procedure on P.58 from step 1 .
61
PLAYBACK MENU
i HOW TO SPECIFY PRINT OPTIONS (DPOF)
DPOF stands for Digital Print Order Format and refers to a format that is used for
recording printing specifications for images shot using a digital camera on media such as
an xD-Picture Card. The recorded specifications include information on which frames are
to be printed.
PLAYBACK MENU
1
i DPOF SET FRAME
1
0
2
0
©
ø (➡P.56)
When you erase the image, the DPOF setting for that image is deleted at the same time.
¥ (➡P.66)
DPOF
OK
This section gives a detailed description of how to order your prints with the FinePix 2650.
On the FinePix 2650, you can specify only one print per image in the DPOF settings.
✽ Note that some printers do not support date and time imprinting or specification of the
number of prints.
✽ Note that the warnings shown below may be displayed while you are specifying the
prints.
2
DATE OFF
1Set the Mode switch to “w”.
2Press the “MENU/OK” button to display the
menu screen.
4
Use “d” or “c” to select “i” DPOF.
If you load an xD-Picture Card that contains frames specified for printing on another
camera, those print specifications are all reset and replaced by the new print specifications.
™ (➡P.111)
Up to 999 frames can be specified on the same xD-Picture Card.
62
Continued on next page...
63
PLAYBACK MENU
3
i DPOF SET FRAME
4
DPOF
53
DPOF
1
0
2
0
6
DPOF
OK
OK
YES
NO
FINISH
DATE ON
DATE ON
OK
BACK
DPOF
1
0
2
0
1
0
2
0
YES
NO
FINISH
OK
1Press “a” or “b” to select “DDATE”.
2Use “d ” or “c ” to select “DATE ON” or
“DATE OFF”.
The selected setting is then valid for all frames
with DPOF settings.
64
1Press “a” to select “OK”.
2Press the “MENU/OK” button.
1 Use “d” or “c” to display the frame for which
you want to specify DPOF settings.
2 Press “a” or “b” to set “YES” for the frame to
be printed and then press the “MENU/OK”
button or “c”.
To specify more DPOF settings, repeat steps 1
and 2.
! DPOF settings cannot be specified for movies.
●
! “TOTAL” shows the total number of frames for which
●
prints have been ordered.
4
BACK
When you have finished the settings, always
select “FINISH” and press the “MENU/OK”
button.
If you press the “BACK” button, no DPOF settings
are specified.
! You can only specify one print per frame in the DPOF
●
settings. Note also that you can specify prints for up
to 999 frames on the same xD-Picture Card.
Continued on next page...
65
PLAYBACK MENU
5 Settings
i DPOF SET FRAME
◆ DPOF settings cannot be changed. ◆
7
1
g ADJUSTING THE MONITOR BRIGHTNESS
10
0
3
2
0
2
BRIGHTNESS
DPOF
DPOF
FINISH OK?
OK
RESET DPOF
OK?
BACK
OK
BACK
If you select a frame for which DPOF settings have
already been specified, the “
”
message appears.
Pressing the “MENU/OK” button erases all the
DPOF settings already specified. You must then
specify the DPOF settings again.
¥
Pressing the “MENU/OK” button confirms the
DPOF settings.
Pressing the “BACK” button returns you to the
settings screen 5 .
! Press the “BACK” button to leave the previous
●
66
Pressing the “MENU/OK” button confirms all the
settings.
settings unchanged.
playback, check that the “ i ” icon is
displayed for the previous settings.
! During
●
OK
BACK
OPTION
SET−UP
LCD BRIGHTNESS
AUTO
MANUAL
You can set the monitor brightness in “Q”, “w”
and “T” mode.
1Press the “MENU/OK” button to display the
menu screen.
2Press “d” or “c” to select “g” OPTION and
then press “a ” or “b ” to select “LCD
BRIGHTNESS”.
3Press the “MENU/OK” button.
1
0
2
0
1 Use “d” or “c” to adjust the LCD monitor
brightness.
2 Press the “MENU/OK” button.
! To exit this procedure without changing the settings,
●
press the “BACK” button.
5
67
g USING SET–UP
1
10
0
3
2
0
2
■ List of settings
Q Still photography mode
SET−UP
POSTVIEW
POWER SAVE
USB MODE
DATE/TIME
OK
A AUTO
S MANUAL
LCD BRIGHTNESS (P.67)
SET–UP
ON
ON
DSC
SET
You can set the SET–UP in “Q”, “w” and “T”
mode.
1Press the “MENU/OK” button to display the
menu screen.
2Press “d” or “c” to select “g” OPTION and
then press “a” or “b” to select “SET–UP”.
3Press the “MENU/OK” button.
68
! The
●
figure above shows the screen for still
photography.
Settings
1
0
2
0
1Press “a” or “b” to select a menu option and
then press “d” or “c” to change the setting.
2Press the “MENU/OK” button.
Display
Factory
default
Explanation
POSTVIEW
ON/OFF
ON
This option specifies whether or not an image checking screen (photography
results) is displayed after you take a shot.
The photography results are displayed for about 2 seconds and then automatically
recorded.
POWER SAVE
ON/OFF
ON
If the camera is not used for approximately 30 seconds, this function temporarily
switches off the LCD monitor. See P.70 for details.
USB MODE
DSC/PC CAM
DSC
DATE/TIME
SET
—
Use this option to correct the date or time. See P.15 for details.
ON/OFF
ON
Use this option to specify whether the LCD monitor is automatically switched ON or
OFF when the Mode switch is set to “Q”.
LOW/HIGH/OFF
LOW
This setting selects the volume of the beep emitted by the camera during camera operation.
Q LCD
BEEP F
LANGUAGE
RESET ALL
! Press “c” for “DATE/TIME” or “RESET ALL”.
●
w Playback mode
—
—
LCD BRIGHTNESS (P.67)
SET–UP
■ SET–UP Menu Options
BACK
OPTION
SET−UP
LCD BRIGHTNESS
AUTO
MANUAL
T Movie mode
—
—
LCD BRIGHTNESS (P.67)
SET–UP
See P.82 for details.
5
ENGLISH/FRANCAIS/ ENGLISH Select English, French or German as the language used for screen display.
DEUTSCH
OK
—
This resets all camera settings (including the photography and playback menu
settings) other than the date and time to the factory default values set at shipment.
When you press “c”, a confirmation screen appears. To proceed, press the
“MENU/OK” button again.
69
SET–UP
g POWER SAVE
6 Software Installation
6.1 The Software Components
SET−UP
POSTVIEW
POWER SAVE
USB MODE
DATE/TIME
OK
ON
ON
DSC
SET
USB Mass Storage
Driver
Factory default
BACK
hPower saving “ON” (default setting)
Power consumption is kept to a minimum to
prevent battery depletion. You should select the
“ON” setting when you are using alkaline
batteries.
iIf the camera is not used for approximately 30
seconds, the LCD monitor switches off temporarily
to reduce power consumption (Sleep mode).
iOnce the camera is in Sleep mode, if it is left
unused for a further 90 seconds, it is automatically
switched off.
iThe charging time for the flash increases slightly
because the flash charging power is reduced.
hPower saving “OFF”
Batteries are more likely to run flat since no
power reduction measures (sleep mode, etc.)
are used. However, this function automatically
switches the camera off if the camera is not
70 used for approximately 2 minutes.
Allows a digital camera to be used
as USB Mass Storage (removable
disk drive, card reader).
When the camera is in Sleep mode, pressing
any button on the camera will switch the LCD
monitor back on. Sleep mode offers a useful
alternative to switching the camera off because
the camera is ready to use far more quickly.
Even when the camera is asleep, you can still
release the shutter and take pictures.
Connect the camera
with “DSC” selected as
the USB setting
(➡P.84).
a USB connection is being used.
! Operation can also be restored by pressing buttons
●
other than the shutter button.
! To switch the camera back on, briefly switch the
●
camera off and then on again.
Connect the camera
with “PC CAM”
selected as the USB
setting (➡P.87).
! Power Save/Auto Power Off does not function when
●
The Sleep function does not operate when the
LCD monitor is switched off, while you are
setting the quality or when the camera is in
SET–UP or Playback mode. However, if the
camera controls are not used for 2 minutes, the
camera automatically switches off.
FinePixViewer
Allows you to display thumbnail lists of the
images stored on your PC or in the camera,
print the images individually or as an index,
display the images at full size and perform
some basic image processing.
PictureHello
Exif Launcher
Used for videoconferencing (Windows only).
Launches the FinePixViewer
software when a camera is
connected.
ImageMixer VCD
for FinePix
Creates a FinePix CD Album.
Acrobat Reader
R
USB PC Camera
Driver
Allows a digital camera to be
used as a PC Camera.
6
Software used to read PDF-format documents on a
personal computer. This software is needed to read the
User’s Guides for FinePixViewer.
QuickTime
Software needed for playing back movies, etc.
✽ Note that the software configuration differs slightly depending on your operating system.
71
6.2 Installation on a Windows PC
6.2.1 Load the CD-ROM into your PC
Do not connect the camera to your PC until
the software installation is completed.
1. Switch on your PC and start up Windows.
✽ If you have already switched on your PC, restart
your PC at this point.
4. The Setup screen appears. Click the
[Installing FinePixViewer] button.
✽ For more information on what is installed, click the
[Read Me First] button and [Using FinePixViewer]
button.
Launching the Installer Manually
1. Double-click the “My Computer” icon.
✽ Windows XP users should click “My
Computer” in the “Start” menu.
2. Right-click “FINEPIX” (CD-ROM drive) in
the “My Computer” window and select
“Open”.
6.2.2 From FinePixViewer installation to restart
1. Pre-installation checking begins. If any
warning messages appear, follow the
instructions given on the screen.
3. Double-click “SETUP” or “SETUP.exe”
in the CD-ROM window.
NOTE
Users of Windows 2000 or Windows XP should log in
using a system administrator account (e.g.
“Administrator”).
2. Quit all other active applications until no
applications are shown in the taskbar.
NOTE
If a “----.dll file not found.” message appears during
installation, there is another application running in the
background. Forcibly shut down the application. Refer
to your Windows manuals for information on how to
forcibly shut down an application.
✽ The way file names are displayed differs as
described below depending on your computer
settings.
• File extensions (3-letter suffixes indicating
the file type) may be shown or hidden. (e.g.
Setup.exe or Setup)
• Text may be shown normally or all in
uppercase (e.g. Setup or SETUP).
✽ The “Add New Hardware Wizard” may be hidden
behind the “Note” message. Check the taskbar,
move the message window and then click the
[Cancel] button.
6
3. Load the enclosed CD-ROM into the CD-ROM
drive. The installer starts up automatically.
72
73
2. A confirmation message appears asking
whether you want to continue with the
installation. Click the [OK] button.
6. Install QuickTime as directed by the onscreen instructions.
7. Install NetMeeting as directed by the onscreen instructions.
✽ If you have already installed QuickTime version
5.0.2 or later, this installation is not performed.
✽ If NetMeeting 3.01 or later is already installed on
your PC, this installation is not performed.
8. Install ImageMixer VCD for FinePix as
directed by the on-screen instructions.
9. Close the “Readme” window.
3. The software version is checked. If the
window shown below appears, click the
[OK] button to uninstall the software.
10. Install WINASPI as directed by the on-screen
instructions.
3 Check the installation destination folder and then
click the [Next >] button.
4 The “Confirmation” screen shown may appear.
To continue with the settings, click the [Yes]
button.
Click the [Agree] button in the “Software License
Agreement” window.
11. Install Windows Media Player as directed
by the on-screen instructions and then
restart your PC.
✽ If the latest version of the software is already installed
on your PC, this installation is not performed. When
next screen appears, click the [Restart] button.
4. The USB drivers are installed.
6
5. Install FinePixViewer.
74
1 FinePixViewer installation begins and notes and
warnings are displayed. When you have
confirmed these, click the [Next >] button.
2 The User License Agreement for this software is
displayed. Read the agreement carefully and
then, if you agree to the terms of the Agreement,
click the [Yes] button. If you click the [No] button,
the software is not installed.
If the “Connection speed” window appears, set the
correct speed for your environment of connection and
then click the [Next] button.
✽ If you do not know your connection speed, simply
click the [Next] button.
In Windows Media Component Setup window, tick
the “I have read the Privacy Statement” checkbox
and then click the [Next >] button.
When you click the [Finish] button, your PC is
restarted.
75
12. After you restart your PC, install DirectX as
directed by the on-screen instructions and
then restart your PC again. If the latest
version of DirectX is already installed on
your PC, this installation is not performed.
13. After you restart your PC, the “FinePixViewer
installation completed” message appears.
Click “Using FinePixViewer” to view the
basic FinePixViewer functions.
15. Proceed with the installation as directed
by the on-screen instructions.
■ To install Acrobat Reader later...
1. Open the “My Computer” window, right-click
the CD-ROM icon and select “Open” to view
the contents of the CD-ROM.
6.3 Installation on a Mac OS 8.6 to 9.2
2. Double-click “Installer for MacOS8.6-9.x”
to launch the Installer.
6.3.1 Check the system software settings
3. The Installer setup screen appears. Click
the [Installing FinePixViewer] button.
■ Enable File Exchange
Check whether File Exchange is active.
To use an xD-Picture Card that is supported by the
camera, the File Exchange utility supplied with Mac
OS must be running.
✽ For more information on what is installed, click the
[Read Me First] button and [Using FinePixViewer]
button.
1. Switch on your Macintosh and start up
Mac OS 8.6 to 9.2.
NOTE
Do not connect the camera to your Macintosh until the
software installation is completed.
2. Double-click “ACROREAD” → “ENGLISH”
folder.
3. Double-click “ar505enu.exe”.
14. To install Acrobat Reader, click “Install
Acrobat Reader”.✽
76
✽ You should install Adobe Acrobat Reader
software to read the FinePixViewer User’s Guide
(PDF).
If you already have the latest version installed,
this step is not required.
4. Proceed with the installation as directed by
the on-screen instructions.
2. Select the Extension Manager in the Control
Panel and check that the File Exchange
check box is ticked. If not, click in the box
so that an
appears and then restart your
Macintosh.
6.3.2 From FinePixViewer installation to restart
1. When you load the enclosed CD-ROM into
the CD-ROM drive, the “FinePix” window
automatically opens.
NOTE
If the “FinePix” window does not open automatically,
double-click the CD-ROM icon.
4. A confirmation message appears asking
whether you want to continue with the
installation. Click the [OK] button.
6
5. The User License Agreement for this
software is displayed. Read the agreement
carefully and then, if you agree to the
terms of the Agreement, click the [Yes]
button. If you click the [No] button, the
77
software is not installed.
6. Select the installation destination for
FinePixViewer and ImageMixer VCD for
FinePix.
7. Install QuickTime as directed by the onscreen instructions and then restart your
Macintosh.
1 Click the [Open] button to open the installation
destination folder.
✽ If you have already installed QuickTime version
5.0.2 or later, this installation is not performed.
8. After you restart your Macintosh, the
“FinePixViewer installation completed”
message appears. Click “Using
FinePixViewer” to view the basic
FinePixViewer functions.
■ To install Acrobat Reader later...
1. Double-click the “FinePix” CD-ROM to
open the CD-ROM window.
2. Double-click “FinePixViewer for Mac OS
8.6-9.x” → “Acrobat Reader” → “English”
folder.
3. Double-click “English Reader Installer”.
4. Proceed with the installation as directed by
the on-screen instructions.
2 Click the [Save] button.
Click [Agree] button in the “License” window.
9. To install Acrobat Reader, click “Install
Acrobat Reader”.✽
✽ You should install Adobe Acrobat Reader
software to read the FinePixViewer User’s Guide
(PDF).
If you already have the latest version installed,
this step is not required.
78
If the “Connection Speed” window appears after you restart your
Macintosh, set the correct speed for your environment of
connection and then click the [Next] button.
✽ If you do not know your connection speed, simply click the
[Next] button.
6
10. Proceed with the installation as directed
by the on-screen instructions.
79
6.4 Installation on a Mac OS X
4. Click the “
” icon.
6.4.1 From FinePixViewer installation to restart
9. Select the Mac OS X startup disk as the
installation destination and click the
[Continue] button.
Only FinePixViewer is installed on Mac OS X.
NOTE
AVI movies cannot be played back on version 10.0.4.
1. Switch your Macintosh on and start up Mac
OS X. Do not launch any other applications.
2. Load the enclosed CD-ROM into the CDROM drive. The “FinePix” window opens.
NOTE
If the “FinePix” window does not open automatically,
double-click the CD-ROM icon.
5. Enter the administrator name and password.
Then click the [OK] button.
10. Click the [Install (upgrade)] button.
11. When you have completed the installation,
click the [Restart] button.
6
6. Click the [Continue] button.
3. Double-click “Installer for MacOS X”.
7. Quit any other programs that are running
and then click the [Continue] button.
8. Click [Continue] button in the “Software
License Agreement” window.
80
81
7 Camera Connection
The “Camera Connection” section explains how
to connect the camera to your computer using
the special USB cable and describes the
functions you can use once the camera and
computer are connected.
If the power cuts out during data transmission,
the data will not be transmitted correctly. Always
use the AC power adapter when connecting the
camera to a computer.
The first time you connect the camera
to your computer refer to Section 6
You must install all the
software before
connecting the camera
to your computer.
CD-ROM
(Software for FinePix SX)
■ DSC (Mass storage device) Mode
7.1 Using the optional AC Power adapter
■ PC CAM (PC Camera) Mode
This function allows you to conduct
videoconferencing sessions between PCs
connected to the Internet (➡P.87).
✽ Videoconferencing (“PictureHello”) is not
supported on Macintosh computers.
✽ Connection is only possible with a FUJIFILM camera
equipped with a “PC Camera” function.
For more information on using the software,
refer to “How to use FinePixViewer” in the HELP
menu which was installed from the CD-ROM.
Always use a FUJIFILM AC Power Adapter AC-3V
(➡P.102).
Use the AC power adapter to avoid losing power
at inconvenient times, such as when you are
downloading photographed images to your
computer. Using the AC power adapter also
allows you to take pictures and play back images
without worrying about depleting the batteries.
✽ See P.107 for notes on using the AC power adapter.
✽ Only connect or disconnect the AC power adapter
when the camera is switched off.
Connecting or disconnecting the AC power adapter
while the camera is switched on temporarily interrupts
the power supply to the camera, so that images or
movies being shot at the time are not recorded.
Failing to switch the camera off first can also result in
damage to the xD-Picture Card or malfunctions during
PC connection.
DC IN 3V
socket
Camera
AC power adapter
✽ Sold separately
Check that the camera is switched off. Plug the
AC power adapter connector into the “DC IN 3V”
socket and then plug the AC power adapter into
the power outlet.
✽ The socket-outlet shall be installed near the equipment
and shall be easily accessible.
✽ The shape of the plug and socket-outlet depends on
the country of use.
Connecting the AC power adapter does not
allow you to charge the Ni-MH batteries. Use the
optional charger (➡P.102) to charge the Ni-MH
batteries.
7
This mode provides a simple way to read images
from an xD-Picture Card and store images on to
an xD-Picture Card (➡P.84).
82
83
7.2 Use at DSC mode
■ Camera Operation
(USB)socket
■ PC Operation
Windows 98/98 SE/Me/2000 Professional
✽ The Windows CD-ROM may also be required
during installation. In this event, switch CD-ROMs
as directed by the on-screen instructions.
Camera AC power
adapter
✽
USB socket
i FinePixViewer automatically starts up.
PC
✽ Sold separately
SET−UP
POSTVIEW
POWER SAVE
USB MODE
DATE/TIME
OK
ON
ON
DSC
SET
BACK
1. Load an xD-Picture Card containing
photographed images into your camera. Plug
the AC power adapter connector into the DC
IN 3V socket on the camera and then plug
the adapter itself into the main power outlet.
2. Slide the power switch to the side to turn
the camera on.
3. Set the “USB MODE” setting in the
“SET–UP” menu to “DSC” (➡P.68, 69).
4. Slide the Power switch to the side to turn
84 the camera off.
5. Switch your PC on.
6. Use the special USB cable to connect the
camera to your computer.
7. Switch the camera on.
If you are using a Windows PC, the driver settings
are specified automatically when installation is
completed. No further action is required.
Always use the prescribed procedure when
disconnecting or switching off the camera
(➡P.90).
✽ On Windows XP and Mac OS X, you must specify the
automatic launch settings the first time you connect
the camera to your computer.
✽ Take care to ensure that the special USB cable is
connected the correct way around and that the plugs
are pushed fully into the connection sockets.
i When the camera and computer are exchanging
data, the self timer lamp flashes and the
viewfinder lamp flashes alternately green and
orange.
i “DSC” appears on the screen.
i Power Save is disabled when the camera is
connected to a USB port.
✽ Before replacing the xD-Picture Card, always
disconnect the camera from the PC using the
procedure on P.90.
✽ Do not disconnect the USB cable when the camera is
communicating with the PC. See P.90 for information
on the disconnection procedure.
✽ Screen for
Windows 98 SE
i A removable disk icon appears and you can
use your PC to transfer files to and from the
camera.
Windows
Macintosh
If the above operations do not occur, you do not
have the required software programs or drivers
installed on your PC. Complete the required PC
setup procedures. Then reconnect the camera
to your PC.
7
85
Windows XP
1. The “Found New Hardware” help message
appears in the bottom-right corner of your
screen. This message will close when the
settings are completed. No action is required.
✽ This step is not required for subsequent connections.
■ When FinePixViewer is not included
in the list of actions to perform
7.3 Use at PC-CAM mode
Select “Take no action” and then select the “Always
do the selected action” checkbox. (This checkbox
may not be shown in some cases.)
Click the [OK] button and launch FinePixViewer
manually.
Camera AC power
adapter
3. A new removable disk icon appears in the
“My Computer” window.
2. Specify the settings in the “AutoPlay” dialog
box.
TIP
The next time you connect the camera, the removable
disk drive icon and name change to the “FinePix” icon
and name.
■ When FinePixViewer is included in
the list of actions to perform
Select “Viewing images using FinePixViewer”
and then select the “Always do the selected
action” checkbox. (This checkbox may not be
shown in some cases.)
Click the [OK] button to launch FinePixViewer.
86
✽
USB socket
PC
✽ Sold separately
SET−UP
POSTVIEW
POWER SAVE
USB MODE
DATE/TIME
OK
Proceed to “Using FinePixViewer” on
page 92.
(USB)socket
ON
ON
PC CAM
SET
BACK
Plug the AC power adapter connector into the
DC IN 3V socket on the camera and then plug
the adapter itself into the main power outlet.
1. Slide the power switch to the side to turn
the camera on.
2. Set the “USB MODE” setting in the
“SET–UP” menu to “PC CAM” (➡P.68, 69).
3. Slide the power switch to the side to turn
the camera off.
✽ Select Macro mode for close-up shots (➡P.43).
Although the “E” icon is not displayed.
4. Switch your PC on.
5. Use the special USB cable to connect the
camera to your computer.
6. Switch the camera on.
If you are using a Windows PC, the driver
settings are automatically specified when
installation ends. Just wait a few moments.
Always use the prescribed procedure when
disconnecting or switching off the camera
(➡P.90).
✽ Take care to ensure that the special USB cable is
connected the correct way around and that the plugs
are pushed fully into the connection sockets.
7
87
■ Camera Operation
■ PC Operation
1. FinePixViewer automatically starts up and
the PictureHello window opens (Windows
only).
2. Check PC operation. The installation
procedure differs depending on the
operating system running on your PC.
✽ This step is not required for subsequent
connections.
Windows 2000 Professional
If the “Digital Signature Not Found” dialog box
appears, click the [Yes] button.
Windows 98/98 SE/Me
The “New Hardware Found” wizard appears. The
wizard will close when the settings are completed.
No action is required.
i When the camera and computer are
exchanging data, the self timer lamp flashes
and the viewfinder lamp flashes alternately
green and orange.
i “PC CAM” appears on the screen.
i Power Save is disabled when the camera is
connected to a USB port.
✽ Do not disconnect the USB cable when the camera is
communicating with the PC. See P.90 for information
on the disconnection procedure.
✽ If the camera is used as a PC camera, a light source
such as fluorescent tube stand can be used to
illuminate the subject and get a brighter image.
✽ When the camera is connected to a computer as a
PC camera, the color tones on the LCD monitor may
change briefly.
88
✽ Screen for Windows 98 SE
If the above operations do not occur, you do not
have the required software programs or drivers
installed on your PC. Complete the required PC
setup procedures. Then reconnect the camera
to your PC.
✽ The Windows CD-ROM may also be required
during installation. In this event, switch CD-ROMs
as directed by the on-screen instructions.
Windows XP
The USB PC Camera Driver is installed automatically.
When the following screen appears, click the
[Continue] button.
3. FinePixViewer starts up automatically and
the live image is displayed.
NOTE
If the live image does not appear, refer to “Troubleshooting”
in the FinePixViewer User’s Guide (PDF).
TIP
The Exif Launcher installed with the FinePixViewer
automatically launches FinePixViewer when you
connect the camera to your PC.
7
89
7.4 Disconnecting the Camera
1
2
Perform the steps shown below before you
switch the camera off. This procedure
differs depending on the operating system
software (or PC) you are using.
Windows 98/98 SE
No PC operation is needed.
Windows Me/2000 Professional/XP
1. Right-click the removable disk icon in the
“My Computer” window and select Eject.
This step is only required in Windows Me.
1. Quit all applications (FinePixViewer etc.)
that are using the camera.
2. Check that the viewfinder lamp is lit green
or that the self timer lamp is off (no data is
being exchanged with the computer).
For a DSC connection, proceed to step 2 .
For a PC CAMERA connection, proceed to step 3 .
✽ Even when “Copying” is no longer displayed on the
computer, the camera and the computer may still be
exchanging data. Always check that the viewfinder
lamp is lit green or that the self timer lamp is off.
90
3. The menu option shown below appears.
Click on this option.
3
(USB)socket
✽ Screen for Windows Me
4. The “Eject hardware” dialog box appears.
Click the [OK] button or the close button.
Macintosh
Drag the “Removable drive” icon on the desktop
to the Trash.
Camera AC power
adapter✽
✽ Sold separately
1. Switch the camera off.
2. Unplug the special USB cable from the
camera.
✽ When you drag the icon to the Trash, “≠”
appears on the camera’s LCD monitor.
2. Left-click the Eject icon in the taskbar and
eject “USB Disk”.
✽ Screen for Windows Me
7
91
4. Check that the files are downloaded from
the camera to your computer and that a
folder with the photography date is
created. Open the folder as shown below.
8 Using FinePixViewer
8.1 Saving Images on Your Computer and viewing images
This section gives a brief overview of how to use
FinePixViewer. Refer to these instructions while you
are using FinePixViewer.
TIP
To open a folder, click on the plus “ + ” symbol (Windows)
or arrow “ ” (Macintosh) to the left of the folder.
Mac OS 8.6-9.2
1. Connect the camera to your computer in
DSC mode (➡P.84).
2
2. When you open the folders shown below
in order, the images in the camera are
displayed in the thumbnail display area.
3
4
1
2
2
3
4
3. Click the [Automatic Taking] button.
2
3
4
92
NOTE
On Windows XP, the
removable disk appears
as “FinePix” (for the
second and subsequent
connections).
OR
2
3
1
1
8.2 Making a FinePix CD Album
1
Mac OS X
Windows
Mac OS
1
Copies multiple images
at once.
For more information on using the software,
refer to “How to use FinePixViewer” in the HELP
menu which was installed from the CD-ROM.
Always use the prescribed procedure when
disconnecting or switching off the camera
(➡P.90).
Windows
1
5. Double-click a still-image thumbnail to
open an image window.
2
3
Indicates the folder in which FinePixViewer is
installed.
For using “ImageMixer VCD for FinePix” to create
CD albums and video CDs.
h To create CD-Rs or video CDs, you will need a
CD-R drive.
h Refer to the “ImageMixer VCD for FinePix” help
file for more detailed information.
h For inquiries regarding “ImageMixer VCD for
FinePix”
PIXELA User Support Center
PIXELA Home Page: http://www.ImageMixer.com/
North America (Los Angels) Telephone: +1-213-341-0163
Europe (U.K.) Telephone: +44-1489-564-764
Asia (Philippines) Telephone: +63-2-438-0090
Japan (Osaka) Telephone: +81-72-224-0181
8
93
8.3 Using the FinePix Internet Service
NOTE
Mac OS X users should refer to P.96.
Using FinePixViewer also allows you to access the
FinePix Internet Service via the Internet.
✽ A working Internet connection is required not only for
FinePix Internet Service, but also online FAQ
(FinePixViewer frequently asked and responses) and
latest updates.
✽ A FinePix Internet Service fees do not include your
Internet service provider (ISP) connection fees or any
phone charges incurred in dialing your ISP’s access
point.
To use the FinePix Internet services, users must
first register.
8.3.2 User Registration
■ For Windows and Mac OS 8.6 to 9.2
NOTE
Your user ID and password are very important. Make
sure you do not forget them.
First-time users
94
✽ Follow the steps below to register. Users can be
registered for free.
1. Launch FinePixViewer.
2. Click the [Register Now] button.
Registered users
8.3.1 Using FAQ
On FinePixViewer,sellct “QuickStart Guide/Online
FAQ” from “Help” menu, then click “FinePixViewer
Q&A”. You may obtain an answer to your question
via internet.
✽ If the country or area where you are living does
not appear in the pull-down list, select “OTHERS”.
3. The “User’s Registration for Internet
Services” dialog box opens. As shown at
right, select [Register Here], then select
the country or region where you are living
and click the [OK] button.
To the user registration
window
The Internet menu is
updated.
✽ If you are not already connected to the Internet,
connect now (A dial-up dialog box may be
displayed).
✽ If you have completed the user registration, select
“Already Registered” (E.g. When you want to reinstall FinePixViewer after completing user
registration).
4. When the browser starts up, proceed as
directed by the on-screen instructions.
8
95
5. Enter the required information in the user
registration page.
Once you complete the registration, a confirmation
E-mail is sent. Wait a few moments until the
message is sent.
■ For Mac OS X
1
2
3
4
To use the FinePix Internet services, users must
first register.
✽ Follow the steps below to register. Users can be
registered for free.
3. Select “User’s registration” and click the
[OK] button.
✽ If you are not already connected to the Internet,
connect now. (A dial-up dialog box may be
displayed.)
✽ Only select “Menu Acquisition” if you have already
completed the user registration process and you
have re-installed “FinePixViewer”, etc.
6. When you have entered all the required
information, click the [Registration] button
96 at the bottom of the page.
3
4
1. Double-click the “FinePixViewer” icon in
the installed folder.
2. Click the [User’s Registration] button. The
“Operation Selection” dialog box appears.
1 Enter the name of your choice (nickname, etc.).
2 Enter a password of your choice using letters
and/or numbers. Then enter the password again
for confirmation.
3 Enter your name.
4 Enter your E-mail address.
5 Enter the remaining required information.
✽ After you register, a confirmation E-mail message
is sent to you. Be sure to enter a valid E-mail
address at which you can receive the message.
✽ The actual user registration page may differ
slightly in appearance from the sample shown
here.
1
2
4. The User’s Registration
dialog box opens.
Select the country or
area where you are
living and click the
[OK] button.
✽ The actual user registration page may differ slightly
in appearance from the sample shown here.
✽ If the country or area where you are living does
not appear in the pull-down list, select “OTHERS”.
<User’s Registration button>
5. When the browser starts up, proceed as
directed by the on-screen instructions.
6. Enter the required information in the user
registration page.
1 Enter the name of your choice (nickname, etc.).
2 Enter a password of your choice using letters
and/or numbers. Then enter the password again
for confirmation.
3 Enter your name.
4 Enter your E-mail address.
5 Enter the remaining required information.
✽ After you register, a confirmation E-mail message
is sent to you. Be sure to enter a valid E-mail
address at which you can receive the message.
✽ The actual user registration page may differ slightly
in appearance from the sample shown here.
7. When you have entered all the required
information, click the [Register] button at
the bottom of the page.
Once you complete the registration, a confirmation
E-mail is sent. Wait a few moments until the
message is sent.
8
97
8.4 Mastering FinePixViewer
8.5 Uninstalling the Software
For more information on FinePixViewer functions
not fully explained in this manual, refer to “How to
Use FinePixViewer” in the Help menu for details.
■ To read “How to Use FinePixViewer”...
Only perform this operation when you no longer
require the installed software or when the software
was not installed correctly.
Bookmarks
Windows
1. Switch on your PC.
You must install Adobe Acrobat Reader. See P.79 for
information on installing Acrobat Reader.
Contents
■ What is explained in “How to Use
FinePixViewer”...
“How to Use FinePixViewer” covers a range of topics,
including batch processing and ordering prints.
3. The “Viewing Slide Shows” information is
displayed. Press the “←” key to view the
previous page or the “→” key to view the
next page.
2. Disconnect the camera (➡P.90, 91).
<To remove FinePixViewer>
<To remove the driver software>
3. Quit all currently running applications.
4. Close all files.
5. Open the “My Computer” window, open
the “Control Panel”, and double-click
“Add/Remove Programs”.
7. When the confirmation message appears,
click the [OK] button. Check your selection
carefully since the process cannot be
cancelled once you click [OK].
■ Example: Looking up slide shows
1. Click “How to Use FinePixViewer” in the
FinePixViewer Help menu.
2. Search for relevant articles by clicking the
corresponding items in the Help
“Bookmarks” or “Contents”. Here, click
“Viewing Slide Shows”.
✽ For more information on using Acrobat Reader,
refer to the Acrobat Reader “Help” menu.
98
6. The “Add/Remove Programs Properties”
window appears. Select the software to be
uninstalled (FinePixViewer or the driver)
and then click the [Add/Remove] button.
8. Automatic uninstallation begins.
When uninstallation ends, click the [OK]
button.
8
99
Macintosh
NOTE
Only perform this operation when you no longer require
the installed software or when the software was not
installed correctly.
Mac OS 8.6-9.2
■ Uninstalling Mass Storage Driver and
PC Camera Driver
1. Check that the camera is not connected to
your Macintosh.
FinePixViewer folder to the Trash. Then
click “Empty Trash” in the “Special” menu.
Mac OS X
■ Uninstalling FinePixViewer
System Expansion Options
e By using the FinePix 2650 together with other optional FUJIFILM products, your system can be
expanded to fill a wide range of uses.
Quit FinePixViewer and DP Editor. Then drag
the installed FinePixViewer folder to the Trash
and select “Empty Trash” in the “Special”
menu.
FinePix 2650
Digital Camera
xD-Picture Card
TV monitor
(commercially available)
(USB)
2. Drag all the files that begin with
“USB04CB...” to the Trash.
3. Restart your Macintosh.
4. Select “Empty Trash” in the “Special” menu.
■ Uninstalling Exif Launcher,
FinePixViewer and DP Editor
1. After you have quit Exif Launcher in “Exif
Launcher Settings” in the FinePixViewer
“Settings” menu, move the Exif Launcher
file from the “Startup Items” folder in the
System folder to the Trash. Then select
“Empty Trash” in the “Special” menu.
2. After you have exited FinePixViewer and
100 DP Editor and then drag the installed
Image Memory
Card Reader
(USB )
(PC card slot )
Personal Computer
(commercially available)
(USB )
PC Card Adapter
Digital Photo Printer
CX-400
101
Accessories Guide
e The optional accessories (sold separately) can make taking pictures with the FinePix 2650 even
easier. For information on how to attach and use the accessories, refer to the instructions provided
with the accessory used.
Visit the FUJIFILM web site for the latest information on camera accessories.
http://home.fujifilm.com/products/digital/index.html
h xD-Picture Card
These are separately available xD-Picture Cards.
Use the following xD-Picture Card:
DPC-16 (16MB)/DPC-32 (32MB)/DPC-64 (64MB)/DPC-128 (128MB)
●
AC Power Adapter AC-3V
Use the AC power adapter when you want to take pictures or play back images
for long periods or when the camera is connected to a computer.
✽ The shape of the AC power adapter, the plug and socket outlet depend on the country.
●
FUJIFILM Rechargeable Battery 2HR-3UF
●
SC-FX26
This is a special case made of polyester that protects the camera against soil, dust
and minor impacts when it is being carried.
h DPC-R1 Image Memory Card Reader
The DPC-R1 provides a quick and easy way to transfer images back and forth
between your PC and an image memory card (xD-Picture Card and SmartMedia).
The DPC-R1 uses the USB interface for high-speed file transfer.
i Compatible with Windows 98/98 SE, Windows Me, Windows 2000 Professional,
Windows XP or iMac, Mac OS 8.6 to 9.2.2, Mac OS X (10.1.2 to 10.1.5) and
models that support USB as standard.
i Compatible with SmartMedia of 3.3V, 4MB to 128MB.
h DPC-AD PC Card Adapter
The PC Card Adapter allows the xD-Picture Card and SmartMedia to be used as
a PC Card Standard ATA-compliant (PCMCIA 2.1) PC card (Type II).
i Compatible with SmartMedia of 3.3V, 2MB to 128MB.
The 2HR-3UF includes two (2) high-capacity AA-size Nickel Metal Hydride batteries.
●
102
FUJIFILM Battery charger with Battery BK-NH (with Euro type or UK type plug)
The BK-NH includes the quick battery charger BCH-NH and 2 Ni-MH batteries.
The BCH-NH can charge 2 Ni-MH batteries in approximately 120 minutes.
Up to 4 Ni-MH batteries can be charged simultaneously.
103
Notes on Using Your Camera Correctly
eBe sure to read this information in conjunction with “Safety Notes” (➡P.119), to ensure that you use
your camera correctly.
■ Places to Avoid
Do not store or use the camera in the following types of
locations:
h In the rain or in very humid, dirty or dusty places.
h In direct sunlight or in places subject to extreme
temperature rises, such as in a closed car in summer.
h Extremely cold places.
h Places subject to strong vibration.
h Places affected by smoke or steam.
h Places subject to strong magnetic fields (such as near
motors, transformers or magnets).
h In contact with chemicals such as pesticides or next to
rubber or vinyl products for long periods of time.
■ Notes on Immersion in Water or Sand
The FinePix 2650 is particularly adversely affected by
water and sand. When you are at the beach or close to
water, ensure that the camera is not exposed to water or
sand. Take care not to place the camera on a wet surface.
Water or sand inside the camera can cause faults that may
be irreparable.
■ Notes on Condensation
104
If the camera is carried suddenly from a cold location into a
warm place, water droplets (condensation) may form on
the inside of the camera or on the lens. When this occurs,
switch the camera off and wait an hour before using the
camera. Condensation may also form on the xD-Picture
card. In this event, remove the xD-Picture Card and wait a
short time before using it again.
■ When the Camera is Unused for Long Periods
If you do not intend to use the camera for a long period of
time, remove the batteries and the xD-Picture Card before
storing the camera.
■ Cleaning Your Camera
h Use a blower brush to remove dust from the lens, LCD
monitor screen or viewfinder as these surfaces and then
wipe lightly with a soft, dry cloth. If any soil remains, apply
a small amount of lens cleaning liquid to a piece of
FUJIFILM lens cleaning paper and wipe gently.
h Do not scratch hard objects against the lens, LCD
monitor screen or viewfinder as these surfaces are easily
damaged.
h Clean the body of the camera with a soft, dry cloth. Do
not use volatile substances such as thinners, benzine or
insecticide, as these may react with camera body and
cause deformation or remove the coating.
■ Using the Camera Overseas
When travelling overseas, do not place your camera in the
check-in baggage. Baggage handling at airports may
subject baggage to violent shocks, and the camera may be
damaged internally even when no external damage is
visible.
Notes on the Power Supply
Applicable Batteries
h AA-size alkaline, Ni-MH (nickel-metal hydride) can be
used with this camera.
Do not use AA-size manganese, lithium or nickelcadmium (Ni-Cd) batteries in your FinePix camera
because the heat generated by the batteries could
damage the camera or cause malfunctions.
h The operating lives of alkaline batteries vary between
brands and the life of batteries you purchase may be
shorter than the alkaline batteries provided with the
camera.
Notes on the Batteries
Incorrect use of the batteries could cause them to leak,
become hot, ignite or burst. Always observe the
precautions given below.
h Do not heat the batteries or throw them into a fire.
h Do not carry or store batteries with metal objects
such as necklaces or hairpins that could come into
contact with the metal positive + and negative _
poles of the batteries.
h Do not expose the batteries to fresh or sea water,
and take particular care to keep the terminals dry.
h Do not attempt to deform, disassemble or modify the
batteries.
h Do not attempt to peel off or cut the batteries casing.
h Do not drop, strike or otherwise subject the batteries
to strong impacts.
h Do not use batteries that are leaking, deformed,
discolored or exhibit any other obvious abnormality.
h Do not store batteries in very warm or moist
locations.
h Keep the batteries out of reach of babies and small
children.
h When loading the batteries into the camera, ensure that
the battery polarity (+ and _ ) is as indicated on the
camera.
h Do not use new batteries together with used
batteries. In the case of rechargeable batteries, do
not use charged and discharged batteries together.
Do not use batteries of different types or brands
together.
h If you do not intend to use the camera for a long
period of time, remove the batteries from the camera.
(Note that if the camera is left with the batteries
removed, the time and date settings are cleared.)
h The batteries may feel warm immediately after being
used. Before removing the batteries, switch the
camera off and wait until the batteries cool down.
h When replacing the batteries, always fit 2 new batteries.
Here, “new batteries” refers to either recently purchased
unused alkaline batteries, or Ni-MH (nickel metal
hydride) batteries that have recently been fully
recharged together.
h In cold locations (at temperatures of +10°C/+50°F or
below), battery performance deteriorates and the time
for which they can be used shortens markedly. This is
particularly true of alkaline batteries. In cold conditions,
put the batteries in your pocket or a similar place to
warm them before loading them into the camera. If you
use a body warmer to warm the batteries, ensure that
they are not in direct contact with the warmer.
105
Notes on the Power Supply
h Soil (such as fingerprints) on the battery terminals can
markedly reduce the number of available shots.
Carefully wipe the battery terminals clean with a soft dry
cloth before loading the batteries.
If any liquid at all leaks from the batteries, wipe the
battery compartment thoroughly and then load new
batteries.
If any battery fluid comes into contact with your
hands or clothing, flush the area thoroughly with
water. Note that battery fluid can cause loss of
eyesight if it gets into your eyes. If this occurs, do not
rub your eyes. Flush the fluid out with clean water
and contact your physician for treatment.
■ Disposing of Batteries
When disposing of batteries, do so in accordance with
your local waste disposal regulations.
■ Notes on Small Rechargeable Batteries (NiMH batteries)
106
h Always use the special battery charger to charge AAsize Ni-MH batteries. Charge the batteries as
described in the instructions provided with the battery
charger.
h Do not use the battery charger to charge batteries
other than those specified for use with the charger.
h Note that the batteries may feel warm immediately
after being charged.
h Ni-MH batteries are not charged at shipment. Be sure
to charge the batteries before using them.
h The camera mechanism is such that it draws a
minute amount of current even when the camera is
switched off. Take particular care not to leave Ni-MH
batteries in the camera for a long period of time as
they can become excessively discharged and may no
longer be usable even when charged.
h Ni-MH batteries self-discharge even when not used.
Always charge Ni-MH batteries before using them. If
the time for which a battery provides power shortens
markedly when it has been correctly charged, this
indicates that the battery has reached the end of its
effective life and should be replaced.
h Soil (fingerprints, etc) on the terminals of Ni-MH
batteries can greatly reduce the number of available
shots. When this occurs, clean the terminals carefully
with a soft dry cloth. Then use up the remaining
charge in the batteries and recharge them.
h Newly purchased batteries or batteries that have
been left unused for an extended period may not be
fully charged. (This is indicated by the immediate
display of the battery low warning or a low number of
available shots.) This is a normal characteristic of the
batteries and does not indicate a fault. Repeatedly
charging and using the batteries 3 or 4 times will
restore them to a normal condition.
h If you repeatedly charge a Ni-MH batteries before it is
fully discharged, it will suffer from the “memory
effect” ✽, causing the battery low warning to appear
while there is still ample charge remaining in the
battery. To restore the batteries to their normal
condition, use up all the charge in the batteries before
recharging them.
✽ Memory effect: A phenomenon affecting the battery
characteristics such that the apparent
battery capacity decreases.
AC Power Adapter
Use only the AC-3V AC Power Adapter (sold
separately) with your FinePix 2650 Digital Camera. The
use of other AC power adapters may result in damage
to your camera.
h This AC power adapter is designed exclusively for
indoor use.
h Plug the connection cord plug securely into the DC
input terminal of the FUJIFILM Digital camera.
h Turn off the power switch of the FUJIFILM Digital
camera before disconnecting the connection cord
from the FUJIFILM Digital camera’s DC input
terminal. To disconnect, take hold of the plug and pull
it out (do not disconnect it by pulling on the cord).
h Do not use this AC power adapter with any device
except the specified device.
h During use, this AC power adapter will become hot to
touch, but this is normal.
h Do not disassemble the AC power adapter. Doing so
could be dangerous.
h Do not use this device in a place with high
temperature and high humidity.
h Do not drop or subject this device to strong shocks.
h This device may emit a humming noise, but this is
normal.
h If used near a radio, this device may cause static, so
play the radio in a distant place.
107
Notes on the xD-Picture Card
■ Image Memory Card
■ Notes on Handling xD-Picture Card
h This Image Memory Card is a new image recording
media (xD-Picture Card) developed for digital
cameras. The Image Memory Card consists of a
semiconductor memory (NAND-type flash memory)
to record digital image data.
The recording process is electrically performed and
enables erasure of existing image data as well as rerecording of new image data.
h When using a new Memory Card, or a Memory Card
that has been initialized by a PC, be sure to initialize
(format/initialize) the card with your digital camera
before using it.
h Keep xD-Picture Cards out of the reach of small
children. When storing xD-Picture Cards, ensure that
they are kept in a location out of the reach of small
children to prevent a card being accidentally
swallowed. An xD-Picture Card could cause suffocation
if accidentally swallowed. If a child swallows an xDPicture Card, seek medical advice immediately.
h Make sure that the memory card is straight when you
insert into the camera etc.
h The memory card is a precision electronic instrument.
Do not apply pressure or shock, and avoid bending it.
h Do not use the memory card in a hot, humid, or
corrosive environment.
h If the contact area on the card is soiled (dust,
fingerprints, etc.), wipe it clean with a soft, dry cloth.
h Clean the memory card with a soft dry piece of cloth
when dirty.
h When you carry or store it, always keep the card in
the anti-static case provided. Use a storage case if
available.
h The memory card can be used reliably for a long
period of time, but will eventually lose its ability to
store and play back image data. At this point, replace
with a new memory card.
h Never remove the xD-Picture Card or switch the
camera off during data recording, during data erasing
(xD-Picture Card formatting) or during frame advance
■ Protecting Your Data
h Data may be lost or destroyed in the following
situations. Please note that FUJIFILM assumes no
responsibility for data that is lost or destroyed.
1. Removal of the memory card or turning the power
off while the memory card is being accessed (i.e.,
during record, erase, initialization, and playback
operations).
2. Improper handling and use of the memory card by
the user or third party.
h We recommend saving your important data to
another media (i.e., MO disk, CD-R, hard disk, etc.).
108
when images are being played back. These actions
could result in damage to the xD-Picture Card.
h The use of xD-Picture Cards is recommended with
the FinePix 2650.
The camera quality cannot be guaranteed when
cards other than those manufactured by FUJIFILM
are used.
h The xD-Picture Card may feel warm when it is
removed from the camera after extended periods of
picture taking or image viewing. This is normal and
does not indicate a fault.
h Do not affix labels to the xD-Picture Card.
This could result in the label peeling off and causing
a fault when the card is inserted or removed.
■ Notes on Using xD-Picture Card with a PC
h If you intend to take photos using an xD-Picture Card
that has been used on a PC, format the xD-Picture
Card on your camera.
h When you format an xD-Picture Card in the camera
and then shoot and record images, a directory
(folder) is automatically created. Image data is then
recorded in this directory.
h Do not change or delete the directory (folder) names
or file names on the xD-Picture Card from your PC as
this will make it impossible to use the xD-Picture
Card in your camera.
h Always use the camera to erase image data on an
xD-Picture Card.
h To edit image data, copy the image data to the PC’s
hard disk and then edit the copied data.
h Do not copy files other than those that will be used by
the camera.
■Specifications
Type
Image memory card for digital cameras
(xD-Picture Card)
Memory type
NAND-type flash memory
Conditions for use Temperature:
0°C to +40°C (+32°F to +104°F)
Humidity:
80% max. (no condensation)
Dimensions
25 mm × 20 mm × 2.2 mm
(0.98 in. × 0.79 in. × 0.09 in.) (W × H × D)
109
Warning Displays
Warning Displayed
(赤点
(Lit red)
(Blinking red)
(赤点
\
e The table below lists the warnings that are displayed on the LCD monitor
Explanation
There is a strong likelihood of camera shake Use flash photography. However, a tripod
because the shutter speed is slow.
should be used for some scenes and modes.
Outside the AE continuous range.
The shot can be taken, but the exposure will not
be correct.
The AF (auto focus) cannot work effectively.
i If the image is too dark, take the picture at a
distance of around 2 m (6.6 ft.) from the subject.
i Use AF lock to take the picture.
No xD-Picture Card is loaded.
Load an xD-Picture Card in the correct direction.
i The xD-Picture Card is not formatted.
i The xD-Picture Card contact area is soiled.
i Format the xD-Picture Card.
i Wipe the contact area on the xD-Picture Card
with a soft dry cloth. It may be necessary to
format the xD-Picture Card. If the error message
is still displayed, replace the xD-Picture Card.
i Contact your FUJIFILM dealer.
i Camera fault.
!CARD ERROR
i The xD-Picture Card contact area is soiled.
i The xD-Picture Card is damaged.
i The xD-Picture Card format is incorrect.
i Camera fault.
The xD-Picture Card is fully recorded.
110
Remedy
Warning Displayed
The batteries in the camera are fully depleted or Replace the batteries or have new batteries
very low on charge.
ready.
i Wipe the contact area on the xD-Picture Card
with a soft dry cloth. It may be necessary to
format the xD-Picture Card. If the error message
is still displayed, replace the xD-Picture Card.
i Contact your FUJIFILM dealer.
Erase some images or use an xD-Picture Card
that has ample free space.
!READ ERROR
Explanation
Remedy
i An attempt was made to playback a frame not i Images cannot be played back.
recorded on this camera.
i Wipe the contact surface on the xD-Picture
i The xD-Picture Card contact area is soiled.
Card thoroughly with a soft, dry cloth. In some
cases, you may have to format the xD-Picture
Card.
i Contact your FUJIFILM dealer.
i Camera fault.
i You attempted to play back a movie file that i Play back the movie on a computer or on the
camera on which it was recorded.
was not recorded on this camera.
The frame number has reached 999–9999.
Take the shot using a formatted xD-Picture Card.
i The data could not be recorded due to an xD- i Re-insert the xD-Picture Card or switch the
camera off and then on again.
Picture Card error or a connection error
between the xD-Picture Card and camera.
i The photographed image cannot be recorded i Use a new xD-Picture Card.
as it is too large to fit in the available space on
the xD-Picture Card.
A protected file was encountered.
Protected files cannot be erased. Remove the
protection.
Prints were specified for more than 1000 frames The maximum number of frames for which
prints can be specified on the same xD-Picture
in the DPOF frame settings.
Card is 999.
Copy the images for which you want to order
prints onto another xD-Picture Card and then
specify the DPOF settings.
111
Troubleshooting
Warning Displays
Warning Displayed
Explanation
Remedy
Camera malfunction or fault.
i Switch the camera on again, taking care not to
touch the lens.
i Switch the camera off and on again.
The lens cover is not open.
Open the lens cover.
Troubleshooting
No power.
e If you think the camera is faulty, check the following once more.
Possible causes
Power cuts out during The batteries are exhausted.
operation.
Batteries runs out quickly.
Solutions
i Load new batteries.
i The batteries are exhausted.
i The AC power adapter plug has come out of i Plug the adapter back in.
the power outlet.
i The batteries are loaded the wrong way round. i Load the batteries in the correct direction.
Load new batteries.
i Camera is being used in extremely cold i Put the batteries in your pocket or another
warm place to heat them and then load them
conditions.
into the camera just before you take a picture.
i Wipe the battery terminals with a clean, dry
i The terminals are soiled.
cloth.
i The batteries have reached the end of their i Load new batteries.
operating lives.
No photograph is taken i No xD-Picture Card is loaded.
when the shutter button is i The xD-Picture Card is fully recorded.
pressed.
i The xD-Picture Card is not formatted.
i The xD-Picture Card contact area is soiled.
i Load an xD-Picture Card.
i Load a new xD-Picture Card or erase some
unwanted frames.
i Format the xD-Picture Card.
i Wipe the xD-Picture Card contact area with
a clean dry cloth.
i Load a new xD-Picture Card.
i The xD-Picture Card is damaged.
i The Power Save function has switched the i Switch the camera on.
camera off.
i Load new batteries.
i The batteries are exhausted.
112
113
Troubleshooting
Troubleshooting
e If you think the camera is faulty, check the following once more.
Possible causes
Solutions
Can’t use the flash to take i The shutter button was pressed while the i Wait until charging is completed before
pictures.
pressing the shutter button.
flash was charging.
i Load new batteries.
i The batteries are exhausted.
i Set the flash mode to Auto, Red-eye
i The Suppressed Flash mode is selected.
Reduction or Forced Flash (The flash cannot
be used in some modes).
The photographed image i The subject is too far away.
i Move to within the effective flash range
is dark even though I used
before taking the shot.
the flash.
i Your finger was covering the flash/flash i Hold the camera correctly.
control sensor.
The playback image is i There is dust on the flash control sensor.
faded when I used the
flash to take a picture.
i Use an applicator such as a cotton swab to
clean the flash control sensor.
The image is blurred.
i Clean the lens.
i Cancel Macro mode.
i The lens is dirty.
i You photographed scenery with Macro mode
selected.
i You took a close-up shot without selecting
Macro mode.
i You are shooting a subject that is not suited
to autofocusing.
i Select Macro mode.
i Use AF/AE lock to take the shot.
There is speckling on the The shot was taken with a slow shutter speed This is a characteristic of CCDs and does not
image.
(long exposure) in a high-temperature indicate a camera fault.
environment.
114
Troubleshooting
Possible causes
Frame erase does not i Some frames may be protected.
erase the frame.
Solutions
i Remove the protection.
The ERASE ALL function
does not erase all the frames.
Can’t format the xD- The xD-Picture Card contact area is soiled.
Picture Card.
Wipe the xD-Picture Card contact area with a
clean dry cloth.
When the camera is i The USB cable is not properly connected to i Set up the camera and the USB cable
connected to a personal
the computer or camera.
correctly.
computer (PC), the shot i The PC is not switched on.
i Switch the PC on.
image appears on the
camera’s LCD monitor.
Nothing happens when I i Camera malfunction.
use the Mode switch.
i The batteries are exhausted.
i Briefly remove the batteries or disconnect
the AC power adapter. Then reload the
batteries or reconnect the AC power adapter
and try again.
i Replace the batteries.
The camera no longer The camera has suffered an unforeseen Briefly remove the batteries or disconnect the
works correctly.
problem.
AC power adapter. Then reload the batteries
or reconnect the AC power adapter and try
again.
115
Specifications
System
h Model
Digital camera FinePix 2650
h Number of effective pixels
2.0 million
h CCD Sensor
1/2.7-inch square pixel CCD
Total number of pixels: Approx. 2.11 million
h Image quality
1600 × 1200 pixels (1.92 million pixels)/1280 × 960 pixels /
640 × 480 pixels
h File format
Still image: JPEG (Exif Ver. 2.2), DPOF-compatible
Movie
: AVI format, motion JPEG
✽Design rule for Camera File system compliant
h Viewfinder
Real image optical; Frame coverage: 80%
h Lens
Fujinon optical 3 × zoom lens
h Aperture
F3.5/F8.7 (automatically selected)
h Storage media
xD-Picture Card (16MB to 128MB)
h Focus distance
f = 6 mm-18 mm
(equivalent to 38 mm-114 mm on a 35 mm camera)
h Exposure control
64 zones TTL metering, Program AE
(exposure compensation available in Manual mode)
h Sensitivity
Equivalent to ISO 100
h White balance
Auto (7 positions selectable in Manual mode)
h Focal range
Normal:Approx. 80 cm (2.6 ft.) to infinity
Macro: Approx. 10 cm (3.9 in.) to 80 cm (2.6 ft.)
h Shutter speeds
Variable-speed, 1/ 2 to 1/ 1000 sec.
(combined with mechanical shutter)
h Standard number of available shots/recording time per xD-Picture Card
116
Quality mode
Number of recorded pixels
Image Data Size
DPC-16 (16 MB)
DPC-32 (32 MB)
DPC-64 (64 MB)
DPC-128 (128 MB)
2M • F
2M • N
1M
0.3M
1600 × 1200
1280 × 960
640 × 480
Approx. 620 KB Approx. 390 KB Approx. 320 KB Approx. 130 KB
#
$
320 × 240
—
160 × 120
—
25
39
49
122
Approx. 94 sec.
Approx. 5.0 min.
50
79
99
247
Approx. 191 sec.
Approx. 10.1 min.
101
159
198
497
Approx. 6.4 min. Approx. 20.2 min.
204
319
398
997
Approx. 12.9 min. Approx. 40.6 min.
h Flash (Auto flash using flash control sensor)
Effective range: Wide-angle Approx. 0.2 m – 3.0 m (0.6 ft. – 9.8 ft.)
: Telephoto Approx. 0.8 m – 3.0 m (2.6 ft. – 9.8 ft.)
Flash modes: Auto, Red-Eye Reduction,
Forced Flash, Suppressed Flash, Slow Synchro
h LCD monitor
1.5-inches, 55,000-pixels D-TFD
h Self-Timer
10 sec. timer clock
Input/Output Terminals
h DC IN 3V (Power input) socket
Special AC Power Adapter AC-3V
h ] (USB) socket
USB (1) for image data output with a personal computer
Power Supply and Others
h Power supply
Use one of the following:
i 2AA-size alkaline batteries
i 2AA-size Ni-MH (nickel metal hydride) batteries (sold separately)
i AC Power Adapter AC-3V (sold separately)
h No. of available shots using battery (battery life)
With LCD monitor With LCD monitor
Battery type
ON
OFF
Alkaline batteries Approx. 150 frames Approx. 250 frames
Ni-MH batteries
Approx. 250 frames✽ Approx. 400 frames✽
HR-3UF 1700 mAh
(Condition: Power saving mode ON, with fully charged battery (Ni-MH))
This indicates the number of available frames shot
consecutively at room temperature with a flash use rate of
50%. Note that these figures may vary depending on the
ambient temperature and the amount of charge in the
battery. The number of available shots or available
shooting time will be lower in cold conditions.
h Conditions for use
Temperature: 0°C to + 40°C (+ 32°F to + 104°F); 80%
humidity or less (no condensation)
h Camera dimensions (W × H × D)
100.4 mm ✕ 65 mm ✕ 51.7 mm / 4.0 in. ✕ 2.6 in. ✕ 2.0 in.
(not including accessories and attachments)
h Camera mass (weight)
Approx. 185 g/6.5 oz (not including, batteries and xD-Picture
Card)
h Mass (weight) for photography
Approx. 240 g/8.5 oz (including batteries and xD-Picture Card)
h Accessories
See P.7
h Optional Accessories
See P.102, 103
✽ These specifications are subject to change without notice.
FUJIFILM shall not be held liable for damages resulting
from errors in this Owner’s Manual.
✽ The LCD monitor on your digital camera is manufactured
using advanced high-precision technology. Even so, small
bright points and anomalous colors (particularly around
text) may appear on the monitor. These are normal display
characteristics and do not indicate a fault with the monitor.
This phenomenon will not appear on the recorded image.
✽ The operation error may be caused in a digital camera by
the strong radio interference (i. e. electric fields, static
electricity, line noise, etc.).
117
118
Explanation of Terms
Safety Notes
DPOF: Digital Print Order Format
DPOF is a format used for recording information on a storage media (image memory card, etc.) that allows
you to specify which of the frames shot using a digital camera are printed and how many prints are made of
each image.
EV:
A number that denotes Exposure Value. The EV is determined by the brightness of the subject and sensitivity
(speed) of the film or CCD. The number is larger for bright subjects and smaller for dark subjects. As the
brightness of the subject changes, a digital camera maintains the amount of light hitting the CCD at a constant
level by adjusting the aperture and shutter speed. When the amount of light striking the CCD doubles, the EV
increases by 1. Likewise, when the light is halved, the EV decreases by 1.
JPEG: Joint Photographics Experts Group
A file format used for compressing and saving color images. The compression ratio can be selected, but the higher the
compression ratio, the poorer the quality of the expanded image.
Motion JPEG:
A type of AVI (Audio Video Interleave) file format that handles images and sound as a single file. Images in
the file are recorded in JPEG format. Motion JPEG can be played back by QuickTime 3.0 or later.
PC Card:
A generic term for cards that meet the PC Card Standard.
PC Card Standard:
A standard for PC cards determined by the PCMCIA.
PCMCIA:
Personal Computer Memory Card International Association (US).
White Balance:
Whatever the kind of the light, the human eye adapts to it so that a white object still looks white. On the other
hand, devices such as digital cameras see a white subject as white by first adjusting the color balance to suit
the color of the ambient light around the subject. This adjustment is called matching the white balance. A
function that automatically matches the white balance is called an Automatic White Balance function.
h To ensure that you use your FinePix 2650 camera
correctly, read these Safety Notes and your Owner’s
Manual carefully beforehand.
h After reading these Safety Notes, store them in a safe
place.
About the Icons
The icons shown below are used in this document to
indicate the severity of the injury or damage that can result
if the information indicated by the icon is ignored and the
product is used incorrectly as a result.
WARNING
This icon indicates that death or
serious injury can result if the
information is ignored.
CAUTION
This icon indicates that personal
injury or material damage can
result if the information is ignored.
The icons shown below are used to indicate the nature of
the information which is to be observed.
Triangular icons notify the user of information
requiring attention (“Important”).
Circular icons with a diagonal bar notify the user
that the action indicated is prohibited
(“Prohibited”).
Filled circles with an exclamation mark notify the
user of an action that must be performed
(“Required”).
WARNING
When a fault arises, switch the camera
off and then remove the batteries and
disconnect the AC power adapter.
Continued use of the camera when it is
emitting smoke, is emitting any unusual
odor, or is in any other abnormal state can
cause a fire or electric shock.
h Contact your FUJIFILM dealer.
Unplug from
power socket.
Do not allow water or foreign objects to
enter the camera.
If water or foreign objects get inside the
camera, switch the camera off, remove the
battery and disconnect and unplug the AC
power adapter.
Continued use of the camera can cause a
fire or electric shock.
h Contact your FUJIFILM dealer.
Do not place the camera on an unstable
surface.
This can cause the camera to fall or tip over
and cause injury.
Do not use the camera in the bathroom
or shower.
This can cause a fire or electric shock.
Do not use in the
bathroom or shower.
119
Safety Notes
WARNING
Never attempt to modify or disassemble
the camera. (Never open the casing.)
Do not use the camera when it has been
dropped or the casing is damaged.
This can cause a fire or electric shock.
● Contact your FUJIFILM dealer.
Never attempt to take pictures while in
motion.
Do not use the camera while you are
walking or operating a moving car or other
vehicle.
This can result in you falling down or being
involved in a traffic accident.
Do not heat, modify or attempt to
disassemble the batteries.
Do not drop or subject the batteries to
impacts.
Do not attempt to recharge lithium or
alkaline batteries.
Do not store the batteries with metallic
products.
Any of these actions can cause the
batteries to burst or leak and cause fire or
injury as a result.
120
WARNING
Do not
disassemble.
Do not touch any metal parts of the
camera during a thunderstorm.
This can cause an electric shock due to
induced current from the lightning discharge.
Do not use the batteries except as
specified.
Load the batteries with the poles positioned
as indicated by the + and _ marks.
Use only the batteries or AC power
adapter specified for use with this
camera.
The use of other power sources can cause a fire.
If the battery leaks and fluid gets into
your eyes or comes into contact with
your skin or clothing, this can cause
injury or loss of eyesight. Immediately
flush the affected area thoroughly with
clean water and seek medical treatment.
When discarding or storing batteries,
cover the battery terminals with
insulation tape.
h Contact with other metallic objects or
batteries could cause the batteries to
ignite or burst.
WARNING
Keep xD-Picture Cards out of the
reach of small children.
Because xD-Picture Cards are small, they
can be accidentally swallowed by small
children. Be sure to store xD-Picture Cards
out of the reach of small children. If a child
accidentally swallows an xD-Picture Card,
seek medical advice immediately
CAUTION
Keep out of the reach of small children.
This product could cause injury in the hands
of a child.
Do not use this camera in locations
severely affected by oil fumes, steam,
humidity or dust.
This can cause a fire or electric shock.
Do not leave this camera in places
subject to extremely high temperatures.
Do not leave the camera in locations such
as a sealed vehicle or in direct sunlight.
This can cause a fire.
Do not place heavy objects on the
camera.
This can cause the heavy object to tip over
or fall and cause injury.
Do not move the camera while the AC
power adapter is still connected.
This can damage the power cord or cables
and cause a fire or electric shock.
121
Safety Notes
IMPORTANT
CAUTION
Do not cover or wrap the camera or the
AC power adapter in a cloth or quilt.
This can cause heat to build up and distort
the casing or cause a fire.
Remove the batteries and disconnect
the AC power adapter when you are
cleaning the camera or if you intend to
leave the camera unused for a long
period.
Failure to do so can cause a fire or electric
shock.
Using a flash too close to a person’s
eyes may temporarily affect the eyesight.
Take particular care when photographing
infants and young children.
When an xD-Picture Card is removed,
the card may fly completely out of the
slot. Use your finger to stop the card
flying out before removing the card.
If an xD-Picture Card is allowed to fly out, it
could hit someone and cause injury.
122
CAUTION
Request regular internal testing and
cleaning for your camera.
Build-up of dust in your camera can cause
a fire or electric shock.
h Contact your FUJIFILM dealer to request
internal cleaning every 2 years.
Be sure to read this page before using theSoftware.
NOTICE
BEFORE OPENING THE PACKAGE OF CD-ROM PROVIDED BY
FUJI PHOTO FILM CO., LTD., PLEASE READ THIS END USER
LICENSE AGREEMENT CAREFULLY. ONLY IF YOU DO AGREE TO
THIS AGREEMENT, YOU WILL BE ABLE TO USE THE SOFTWARE
RECORDED ON THE CD-ROM. BY OPENING THE PACKAGE, YOU
ACCEPT AND AGREE TO BE BOUND BY THIS AGREEMENT.
End User License Agreement
This End User License Agreement (“Agreement”) is an agreement between Fuji Photo
Film Co., Ltd. (“FUJIFILM”) and you, which sets forth the terms and conditions of the
license granted for you to use the software provided by FUJIFILM.
The CD-ROM contains third party software. In case a separate agreement is provided by
a third party supplier for its software, the provisions of such separate agreement shall
apply to the use of such third party software, prevailing over those of this Agreement.
1. Definitions.
(a) “Media” means the CD-ROM titled “Software for FinePix SX” which is provided
to you together with this Agreement.
(b) “Software” means the software which is recorded on Media.
(c) “Documentation” means the operation manuals of Software and other related
written materials which are provided to you together with Media.
(d) “Product” means Media (including Software) and Documentation collectively.
2. Use of Software.
FUJIFILM grants to you a nontransferable, nonexclusive license:
(a) to install one copy of Software onto one computer in binary machine executable form;
(b) to use Software on the computer onto which Software is installed; and
(c) to make one backup copy of Software.
3. Restrictions.
3.1 You shall not distribute, rent, lease or otherwise transfer all or any part of
Software, Media or Documentation to any third party without FUJIFILM’s prior
written consent. You also shall not sublicense, assign or otherwise transfer all
or any part of the rights granted to you by FUJIFILM under this Agreement
without FUJIFILM’s prior written consent.
3.2 Except as expressly granted by FUJIFILM hereunder, you shall not copy or
reproduce all or any part of Software or Documentation.
3.3 You shall not modify, adapt or translate Software or Documentation. You also
shall not alter or remove copyright and other proprietary notices that appear on
or in Software or Documentation.
3.4 You shall not, or shall not have any third party, reverse-engineer, decompile,
or disassemble Software.
4. Ownership.
All copyrights and other proprietary rights to Software and Documentation are
owned and retained by FUJIFILM or the third party suppliers as indicated on or in
Software or Documentation. Nothing contained herein shall be construed,
expressly or implicitly, as transferring or granting any right, license, or title to you
other than those explicitly granted under this Agreement.
5. Limited Warranty.
FUJIFILM warrants to you that Media is free from any defect in material and
workmanship under normal use for ninety (90) days from the date of your receipt of
Media. Should Media not meet the foregoing warranty, FUJIFILM shall replace
such defective Media with other Media bearing no defect. FUJIFILM’s entire liability
and your sole and exclusive remedy with regard to any defect in Media shall be
expressly limited to such FUJIFILM’s replacement of Media as provided herein
6. DISCLAIMER OF WARRANTY.
EXCEPT AS PROVIDED IN SECTION 5 HEREIN, FUJIFILM PROVIDES
PRODUCT “AS IS” AND WITHOUT WARRANTIES OF ANY KIND, EXPRESS OR
IMPLIED. FUJIFILM SHALL MAKE NO WARRANTY, EXPRESS, IMPLIED OR
STATUTORY, AS TO ANY OTHER MATTERS, INCLUDING, BUT NOT LIMITED
TO NON-INFRINGEMENT OF ANY COPYRIGHT, PATENT, TRADE SECRET,
OR ANY OTHER PROPRIETARY RIGHTS OF ANY THIRD PARTY,
MARCHANTABILITY, OR FITNESS FOR ANY PARTICULAR PURPOSE.
7. LIMITATION OF LIABILITY.
IN NO EVENT SHALL FUJIFILM HAVE ANY LIABILITY FOR ANY GENERAL,
SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL, INCIDENTAL, OR OTHER
DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS OR LOST SAVINGS)
INCURRED FROM THE USE OF OR INABILITY TO USE PRODUCT EVEN IF
FUJIFILM HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
8. No export.
You acknowledge that neither Software nor any part thereof, will be transferred, or
exported to any country or used in any manner in violation of any export control
laws and regulations to which Software is subject.
9. Termination.
In case you breach any of the terms and conditions hereof, FUJIFILM may
immediately terminate this Agreement without any notice.
10. Term.
This Agreement is effective until the date when you cease to use
Software, unless earlier terminated in accordance with Section 9 hereof.
11. Obligation upon termination.
Upon termination or expiration of this Agreement, you shall, at your own
responsibility and expense, delete or destroy immediately all Software
(including its copies), Media and Documentation.
12. Governing Law.
This Agreement shall be governed by and construed in accordance with
laws of Japan.
123
26-30, Nishiazabu 2-chome, Minato-ku, Tokyo 106-8620, Japan
Printed in Japan
Printed on recycled paper.
FGS-204107-FG