Operating instructions | FujiFilm DVD-A1XV Network Card User Manual

DVD AUDIO-VIDEO/SUPER AUDIO CD PLAYER
DVD-A1XV
OPERATING INSTRUCTIONS
POWER OFF
POWER ON
HDMI/DVI
SELECT
OPEN/
CLOSE
FORMAT
NTSC/PAL
SUPER AUDIO
CD SETUP
PROGRAM
/DIRECT
CLEAR
SEARCH MODE
CALL
SUBTITLE
AUDIO
BACK LIGHT
ANGLE
TOP MENU
OPEN/CLOSE
PLAY
DISPLAY
STOP
MENU
RETURN
STOP
STILL/PAUSE
SKIP
PLAY
SLOW/SEARCH
STILL / PAUSE
PAGE
ON / STANDBY
REPEAT
A-B
RANDOM
MARKER
ZOOM
SETUP
PICTURE
ADJUST
PICT ADJ.
MEMORY
VIDEO MODE
HDMI / DVI
SELECT
FORMAT
SUPER
AUDIO CD
SET UP
PURE
DIRECT
SELECT
PUSH ENTER
DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER
DIMMER
PURE DIRECT
DVD-A1XV
RC-993
SELECT
IMPORTANT TO SAFETY
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR REFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
THE COMPACT DISC PLAYER SHOULD NOT BE ADJUSTED OR
REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED SERVICE
PERSONNEL.
CAUTION:
1. Handle the power supply cord carefully
Do not damage or deform the power supply cord. If it is damaged or
deformed, it may cause electric shock or malfunction when used.
When removing from wall outlet, be sure to remove by holding the plug
attachment and not by pulling the cord.
• Copyrights
It is prohibited by law to reproduce, broadcast, rent or play discs in public
without the consent of the copyright holder.
• Urheberrechte
Die Reproduktion, Ausstrahlung, der Verleih sowie die öffentliche
Wiedergabe
von
Discs
erfordern
die
Zustimmung
des
Urheberrechtinhabers.
2. Do not open the top cover
In order to prevent electric shock, do not open the top cover.
If problems occur, contact your DENON DEALER.
• Droits d’auteur
La reproduction, la diffusion, la location, le prêt ou la lecture publique de
ces disques sont interdits sans le consentement du détenteur des droits
d’auteur.
3. Do not place anything inside
Do not place metal objects or spill liquid inside the DVD audio-video/
Super audio CD player.
Electric shock or malfunction may result.
• Copyright
La duplicazione, la trasmissione, il noleggio e la riproduzione dei dischi in
pubblico senza l’autorizzazione scritta del titolare dei diritti di copyright
sono vietati dalla legge.
Please, record and retain the Model name and serial number of your set
shown on the rating label.
Model No. DVD-A1XV
Serial No.
• Derechos de Autor
De acuerdo con las leyes está prohibido reproducir, emitir, alquilar o
interpretar discos en público sin la autorización del propietario de los
derechos de autor.
• Auteurstrechten
Het zonder toestemming van de auteursrechthebbenden reproduceren,
uitzenden, verhuren of in het openbaar afspelen van discs is wettelijk
verboden.
CAUTION
• Upphovsrätt
Enligt lagen är det förbjudet att återge, utsända, hyra ut eller spela skivor
för allmän publik med mindre tillstånd från ägaren till upphovsrätten först
har inhämtats.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
NOTE:
This DVD audio-video/Super audio CD player uses the semiconductor laser.
To allow you to enjoy music at a stable operation, it is recommended to
use this in a room of 5 °C (41 °F) ~ 35 °C (95 °F).
2
CAUTION:
• DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product, to which this
declaration relates, is in conformity with the following standards:
EN60065, EN55013, EN55020, EN61000-3-2 and EN61000-3-3.
Following the provisions of 73/23/EEC, 89/336/EEC and 93/68/EEC
Directive.
• The ventilation should not be impeded by covering the ventilation
openings with items, such as newspapers, table-cloths, curtains, etc.
• No naked flame sources, such as lighted candles, should be placed on the
apparatus.
• Please be care the environmental aspects of battery disposal.
• The apparatus shall not be exposed to dripping or splashing for use.
• No objects filled with liquids, such as vases, shall be placed on the
apparatus.
• ÜBEREINSTIMMUNGSERKLÄRUNG
Wir erklären unter unserer Verantwortung, daß dieses Produkt, auf das
sich diese Erklärung bezieht, den folgenden Standards entspricht:
EN60065, EN55013, EN55020, EN61000-3-2 und EN61000-3-3.
Entspricht den Verordnungen der Direktive 73/23/EEC, 89/336/EEC und
93/68/EEC.
ACHTUNG:
• Die Belüftung sollte auf keinen Fall durch das Abdecken der
Belüftungsöffnungen durch Gegenstände wie beispielsweise Zeitungen,
Tischtücher, Vorhänge o. Ä. behindert werden.
• Auf dem Gerät sollten keinerlei direkten Feuerquellen wie beispielsweise
angezündete Kerzen aufgestellt werden.
• Bitte beachten Sie bei der Entsorgung der Batterien die geltenden
Umweltbestimmungen.
• Das Gerät sollte keinerlei Flüssigkeit, also keinem Tropfen oder Spritzen
ausgesetzt werden.
• Auf dem Gerät sollten keinerlei mit Flüssigkeit gefüllten Behälter wie
beispielsweise Vasen aufgestellt werden.
• DECLARATION DE CONFORMITE
Nous déclarons sous notre seule responsabilité que l’appareil, auquel se
réfère cette déclaration, est conforme aux standards suivants:
EN60065, EN55013, EN55020, EN61000-3-2 et EN61000-3-3.
D’après les dispositions de la Directive 73/23/EEC, 89/336/EEC et
93/68/EEC.
• DICHIARAZIONE DI CONFORMITÀ
Dichiariamo con piena responsabilità che questo prodotto, al quale la
nostra dichiarazione si riferisce, è conforme alle seguenti normative:
EN60065, EN55013, EN55020, EN61000-3-2 e EN61000-3-3.
In conformità con le condizioni delle direttive 73/23/EEC, 89/336/EEC e
93/68/EEC.
ATTENTION:
• La ventilation ne doit pas être gênée en recouvrant les ouvertures de la
ventilation avec des objets tels que journaux, rideaux, tissus, etc.
• Aucune flamme nue, par exemple une bougie, ne doit être placée sur
l’appareil.
• Veillez à respecter l’environnement lorsque vous jetez les piles usagées.
• L’appareil ne doit pas être exposé à l’eau ou à l’humidité.
• Aucun objet contenant du liquide, par exemple un vase, ne doit être placé
sur l’appareil.
• DECLARACIÓN DE CONFORMIDAD
Declaramos bajo nuestra exclusiva responsabilidad que este producto al
que hace referencia esta declaración, está conforme con los siguientes
estándares:
EN60065, EN55013, EN55020, EN61000-3-2 y EN61000-3-3.
Siguiendo las provisiones de las Directivas 73/23/EEC, 89/336/EEC y
93/68/EEC.
PRECAUZIONI:
• EENVORMIGHEIDSVERKLARING
• Le aperture di ventilazione non devono essere ostruite coprendole con
oggetti, quali giornali, tovaglie, tende e così via.
• Non posizionare sull'apparecchiatura fiamme libere, come ad esempio le
candele accese.
• Prestare attenzione agli aspetti legati alla tutela dell'ambiente quando si
smaltisce la batteria.
• L'apparecchiatura non deve essere esposta a gocciolii o spruzzi.
• Non posizionare sull'apparecchiatura nessun oggetto contenete liquidi,
come ad esempio i vasi.
Wij verklaren uitsluitend op onze verantwoordelijkheid dat dit produkt,
waarop deze verklaring betrekking heeft, in overeenstemming is met de
volgende normen:
EN60065, EN55013, EN55020, EN61000-3-2 en EN61000-3-3.
Volgens de bepalingen van de Richtlijnen 73/23/EEC, 89/336/EEC en
93/68/EEC.
• ÖVERENSSTÄMMELSESINTYG
Härmed intygas helt på eget ansvar att denna produkt, vilken detta intyg
avser, uppfyller följande standarder:
EN60065, EN55013, EN55020, EN61000-3-2 och EN61000-3-3.
Enligt stadgarna i direktiv 73/23/EEC, 89/336/EEC och 93/68/EEC.
PRECAUCIÓN:
• La ventilación no debe quedar obstruida por hacerse cubierto las
aperturas con objetos como periódicos, manteles, cortinas, etc.
• No debe colocarse sobre el aparato ninguna fuente inflamable sin
protección, como velas encendidas.
• A la hora de deshacerse de las pilas, respete la normativa para el cuidado
del medio ambiente.
• No se expondrá el aparato al goteo o salpicaduras cuando se utilice.
• No se colocarán sobre el aparato objetos llenos de líquido, como jarros.
CLASS 1 LASER PRODUCT
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
WAARSCHUWING:
• De ventilatie mag niet worden belemmerd door de ventilatieopeningen af
te dekken met bijvoorbeeld kranten, een tafelkleed, gordijnen, enz.
• Plaats geen open vlammen, bijvoorbeeld een brandende kaars, op het
apparaat.
• Houd u steeds aan de milieuvoorschriften wanneer u gebruikte batterijen
wegdoet.
• Stel het apparaat niet bloot aan druppels of spatten.
• Plaats geen voorwerpen gevuld met water, bijvoorbeeld een vaas, op het
apparaat.
,,
CLASS 1
,,
LASER PRODUCT
ADVARSEL:
VAROITUS!
VARNING–
OBSERVERA:
USYNLIG LASERSTRÅLING VED ÅBNING, NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION.
UNDGÅ UDSAETTELSE FOR STRÅLING.
LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ
KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA
ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1
YLITTÄVÄLLE NÄKYMÄMTTÖMÄLLE LASERSÄTEILYLLE.
OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN I DENNA
BRUKSANVISNING SPECIFICERATS, KAN ANVÄNDAREN
UTSÄTTAS FÖR OSYNLIG LASERSTRÅLNING SOM
ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1.
• Ventilationen bör inte förhindras genom att täcka för
ventilationsöppningarna med föremål såsom tidningar, bordsdukar,
gardiner osv.
• Inga blottade brandkällor, såsom tända ljus, bör placeras på apparaten.
• Tänk på miljöaspekterna när du bortskaffar batteri.
• Apparaten får inte utsättas för vätska.
• Inga objekt med vätskor, såsom vaser, får placeras på apparaten.
ATTENZIONE: QUESTO APPARECCHIO E’ DOTATO DI DISPOSITIVO
OTTICO CON RAGGIO LASER.
L’USO IMPROPRIO DELL’APPARECCHIO PUO’ CAUSARE PERICOLOSE
ESPOSIZIONI A RADIAZIONI!
3
NOTE ON USE / HINWEISE ZUM GEBRAUCH /
OBSERVATIONS RELATIVES A L’UTILISATION / NOTE SULL’USO
NOTAS SOBRE EL USO / ALVORENS TE GEBRUIKEN / OBSERVERA
• Avoid high temperatures.
Allow for sufficient heat dispersion when installed
on a rack.
• Vermeiden Sie hohe Temperaturen.
Beachten Sie, daß eine ausreichend Luftzirkulation
gewährleistet wird, wenn das Gerät auf ein Regal
gestellt wird.
• Eviter des températures élevées
Tenir compte d’une dispersion de chaleur suffisante
lors de l’installation sur une étagère.
• Evitate di esporre l’unità a temperature alte.
Assicuratevi che ci sia un’adeguata dispersione del
calore quando installate l’unità in un mobile per
componenti audio.
• Evite altas temperaturas
Permite la suficiente dispersión del calor cuando
está instalado en la consola.
• Vermijd hoge temperaturen.
Zorg voor een degelijk hitteafvoer indien het
apparaat op een rek wordt geplaatst.
• Undvik höga temperaturer.
Se till att det finns möjlighet till god värmeavledning
vid montering i ett rack.
• Handle the power cord carefully.
Hold the plug when unplugging the cord.
• Gehen Sie vorsichtig mit dem Netzkabel um.
Halten Sie das Kabel am Stecker, wenn Sie den
Stecker herausziehen.
• Manipuler le cordon d’alimentation avec précaution.
Tenir la prise lors du débranchement du cordon.
• Manneggiate il filo di alimentazione con cura.
Agite per la spina quando scollegate il cavo dalla
presa.
• Maneje el cordón de energía con cuidado.
Sostenga el enchufe cuando desconecte el cordón
de energía.
• Hanteer het netsnoer voorzichtig.
Houd het snoer bij de stekker vast wanneer deze
moet worden aan- of losgekoppeld.
• Hantera nätkabeln varsamt.
Håll i kabeln när den kopplas från el-uttaget.
• Keep the set free from moisture, water, and dust.
• Halten Sie das Gerät von Feuchtigkeit, Wasser und
Staub fern.
• Protéger l’appareil contre l’humidité, l’eau et
lapoussière.
• Tenete l’unità lontana dall’umidità, dall’acqua e dalla
polvere.
• Mantenga el equipo libre de humedad, agua y polvo.
• Laat geen vochtigheid, water of stof in het apparaat
binnendringen.
• Utsätt inte apparaten för fukt, vatten och damm.
• Unplug the power cord when not using the set for
long periods of time.
• Wenn das Gerät eine längere Zeit nicht verwendet
werden soll, trennen Sie das Netzkabel vom Netzstecker.
• Débrancher le cordon d’alimentation lorsque l’appareil
n’est pas utilisé pendant de longues périodes.
• Disinnestate il filo di alimentazione quando avete
l’intenzione di non usare il filo di alimentazione per un
lungo periodo di tempo.
• Desconecte el cordón de energía cuando no utilice el
equipo por mucho tiempo.
• Neem altijd het netsnoer uit het stopkontakt wanneer
het apparaat gedurende een lange periode niet wordt
gebruikt.
• Koppla ur nätkabeln om apparaten inte kommer att
användas i lång tid.
* (For sets with ventilation holes)
• Do not obstruct the ventilation holes.
• Die Belüftungsöffnungen dürfen nicht verdeckt
werden.
• Ne pas obstruer les trous d’aération.
• Non coprite i fori di ventilazione.
• No obstruya los orificios de ventilación.
• De ventilatieopeningen mogen niet worden beblokkeerd.
• Täpp inte till ventilationsöppningarna.
4
• Do not let foreign objects in the set.
• Keine fremden Gegenstände in das Gerät kommen
lassen.
• Ne pas laisser des objets étrangers dans l’appareil.
• E’ importante che nessun oggetto è inserito
all’interno dell’unità.
• No deje objetos extraños dentro del equipo.
• Laat geen vreemde voorwerpen in dit apparaat vallen.
• Se till att främmande föremål inte tränger in i
apparaten.
• Do not let insecticides, benzene, and thinner come in
contact with the set.
• Lassen Sie das Gerät nicht mit Insektiziden, Benzin
oder Verdünnungsmitteln in Berührung kommen.
• Ne pas mettre en contact des insecticides, du
benzène et un diluant avec l’appareil.
• Assicuratevvi che l’unità non venga in contatto con
insetticidi, benzolo o solventi.
• No permita el contacto de insecticidas, gasolina y
diluyentes con el equipo.
• Laat geen insektenverdelgende middelen, benzine of
verfverdunner met dit apparaat in kontakt komen.
• Se till att inte insektsmedel på spraybruk, bensen och
thinner kommer i kontakt med apparatens hölje.
• Never disassemble or modify the set in any way.
• Versuchen Sie niemals das Gerät auseinander zu
nehmen oder auf jegliche Art zu verändern.
• Ne jamais démonter ou modifier l’appareil d’une
manière ou d’une autre.
• Non smontate mai, nè modificate l’unità in nessun
modo.
• Nunca desarme o modifique el equipo de ninguna
manera.
• Nooit dit apparaat demonteren of op andere wijze
modifiëren.
• Ta inte isär apparaten och försök inte bygga om den.
About the operating instructions on the
CD-ROM
[ ENGLISH ]
A propos du mode d’emploi fourni sur le
CD-ROM
[ FRANCAIS ]
1. Check the computer environment.
1. Vérifier l’équipement de l’ordinateur.
• Adobe Acrobat Reader 5.0 or later is required to view the text.
• If Adobe Acrobat Reader is not installed on the computer, install it from
the included CD-ROM. (Adobe Reader 6.0)
[Windows]
• Adobe Acrobat Reader 5.0 ou ultérieur est nécessaire pour lire le
texte.
• Si Adobe Acrobat Reader n’est pas installé sur l’ordinateur, installez-le
à partir du CD-ROM fourni. (Adobe Reader 6.0)
[Windows]
AdbeRdr60_ece.exe
• Adobe Reader 6.0 system requirements
AdbeRdr60_fra_full.exe
• Configuration requise pour Adobe Reader 6.0
[Windows]
[Windows]
• Intel Pentium processor
• Microsoft Windows 98 Second Edition, Windows Millennium
Edition, Windows NT 4.0 with Service Pack 6, Windows 2000 with
Service Pack 2, Windows XP Professional or Home Edition, Windows
XP Tablet PC Edition
• 32MB of RAM (64MB recommended)
• 60MB of available hard-disk space
• Internet Explorer 5.01, 5.5, 6.0, or 6.1
• Processeur Intel Pentium
• Microsoft Windows 98 Deuxième Edition, Windows Millennium
Edition, Windows NT 4.0 avec Service Pack 6, Windows 2000 avec
Service Pack 2, Windows XP Edition Professionnelle ou Familiale,
Windows XP Edition Tablet PC
• 32 Mo de RAM (64 Mo recommandés)
• 60 Mo d’espace disque disponible
• Microsoft Internet Explorer 5.01, 5.5, 6.0 ou 6.1
2. Open the operating instructions’ file.
2. Ouvrez le fichier du mode d’emploi.
• Open the file “DVDA1XV_ENGLISH.pdf”.
• Ouvrez le fichier “DVDA1XV_FRANCAIS.pdf”.
[If you cannot view the contents of the CD-ROM]
[Si vous ne pouvez pas lire le contenu du CD-ROM]
• Contact one of the sales agents shown on the included “Service
Station” list. The operating instructions in the requested language
will be sent to you in writing (copy).
• Contactez un des revendeurs figurant dans la liste “Service Station”
fournie. Le mode d’emploi dans la langue requise vous sera envoyé
sur papier (copie).
Wissenswertes über die Bedienungsanleitung
[ DEUTSCH ]
auf der CD-ROM
Informazioni sul Manuale delle istruzioni
incluso nel CD-ROM
[ ITALIANO ]
1. Überprüfen Sie die Computer-Umgebung.
1. Controllare l’ambiente informatico.
• Adobe Acrobat Reader 5.0 oder neuer ist für das Lesen des Textes
erforderlich.
• Falls Adobe Acrobat Reader mich auf dem Computer installiert ist,
installieren Sie das Programm bitte von der im Lieferumfang enthaltenen
CD-ROM aus. (Adobe Reader 6.0)
[Windows]
• È necessario disporre di Adobe Acrobat Reader 5.0 o versione
successiva per visualizzare il testo.
• Se Adobe Acrobat Reader non è installato sul computer in uso, installarlo
dal CD-ROM incluso. (Adobe Reader 6.0)
[Windows]
AdbeRdr60_deu_full.exe
• Adobe Reader 6.0 Systemanforderungen
AdbeRdr60_ita_full.exe
• Requisiti di sistema per Adobe Reader 6.0
[Windows]
[Windows]
• Intel Pentium-Prozessor
• Microsoft Windows 98 Second Edition, Windows Millennium
Edition, Windows NT 4.0 mit Service Pack 6, Windows 2000 mit
Service Pack 2, Windows XP Professional oder Home, Windows XP
Tablet PC Edition
• 32 MB RAM (64 MB empfohlen)
• 60 MB freier Festplattenspeicher
• Internet Explorer 5.01, 5.5, 6.0 oder 6.1
• Processore Intel Pentium
• Microsoft Windows 98 Second Edition, Windows Millennium
Edition, Windows NT 4.0 con Service Pack 6, Windows 2000 con
Service Pack 2, Windows XP Professional o Home Edition, Windows
XP Tablet PC Edition
• 32 MB di RAM (64 MB consigliati)
• 60 MB di spazio disponibile su disco rigido
• Internet Explorer 5.01, 5.5, 6.0 o 6.1
2. Öffnen Sie die Datei mit der Bedienungsanleitung.
2. Aprire il file del Manuale delle istruzioni.
• Öffnen Sie die Datei “DVDA1XV_DEUTSCH.pdf”.
• Aprire il file “DVDA1XV_ITALIANO.pdf”.
[Falls Sie den Inhalt der CD-ROM nicht lesen können]
[Se non è possibile visualizzare il contenuto del CD-ROM]
• Konsultieren Sie eine der in der im Lieferumfang enthaltenen
“Kundenservice-Stellen“ aufgelisteten Verkaufsstellen. Die in der
gewünschten Sprache verfasste Bedienungsanleitung wird Ihnen
dann als Schriftdokument (Kopie) zugestellt.
• Rivolgersi a un agente di vendita presente nell'elenco “Stazione di
servizio” incluso. Il Manuale delle istruzioni nella lingua richiesta
verrà inviato per posta (copia).
5
Acerca de las instrucciones de funcionamiento
[ ESPAÑOL ]
del CD-ROM
Om bruksanvisningarna på CD-ROMskivan
[ SVENSKA ]
1. Compruebe el entorno del ordenador.
1. Kontrollera datormiljön.
• Se necesita la versión del Adobe Acrobat Reader 5.0 o una superior
para ver el texto.
• Si la versión del Adobe Acrobat Reader no está instalada en el ordenador,
instálela desde el CD-ROM suministrado. (Adobe Reader 6.0)
[Windows]
• Adobe Acrobat Reader 5.0 eller senare behövs för att visa texten.
• Om Adobe Acrobat Reader inte är installerad på datorn, ska du installera
det från den medföljande CD-ROM-skivan. (Adobe Reader 6.0)
[Windows]
AdbeRdr60_esp_full.exe
• Requisitos del sistema de Adobe Reader 6.0
AdbeRdr60_sve_full.exe
• Adobe Reader 6.0 – systemkrav
[Windows]
[Windows]
• Procesador Intel Pentium
• Microsoft Windows 98 Second Edition, Windows Millennium
Edition, Windows NT 4.0 con Service Pack 6, Windows 2000 con
Service Pack 2, Windows XP Professional o Home Edition, Windows
XP Tablet PC Edition
• 32 MB de RAM (se recomiendan 64 MB)
• 60 MB de espacio disponible en el disco duro
• Internet Explorer 5.01, 5.5, 6.0 ó 6.1
• Intel Pentium processor
• Microsoft Windows 98 Second Edition, Windows Millennium
Edition, Windows NT 4.0 med Service Pack 6, Windows 2000 med
Service Pack 2, Windows XP Professional eller Home Edition,
Windows XP Tablet PC Edition
• 32 MB RAM (64 MB rekommenderas)
• 60 MB ledigt hårddiskutrymme
• Internet Explorer 5.01, 5.5, 6.0 eller 6.1
2. Abra el archivo de las instrucciones de funcionamiento.
2. Öppna filen med instruktioner.
• Abra el archivo “DVDA1XV_ESPANOL.pdf”.
• Öppna filen “DVDA1XV_SVENSKA.pdf”.
[Si no puede visualizar el contenido del CD-ROM]
[Om du inte kan visa innehållet på CD-ROM-skivan]
• Póngase en contacto con uno de los agentes de venta que aparecen
en la lista “Estación de servicio” suministrada. Se le enviaran las
instrucciones de funcionamiento en el idioma solicitado por escrito
(copia).
• Kontakta en av försäljningsagenterna i “Service Station”-listan.
Bruksanvisningarna på nödvändigt språk kommer att skickas till dig
skriftligt (kopia).
Over de gebruiksaanwijzing op de CD-ROM
[ NEDERLANDS ]
1. Controleer de computeromgeving.
• Om de tekst te bekijken, is Adobe Acrobat Reader 5.0 of hoger vereist.
• Als Adobe Acrobat Reader niet geïnstalleerd is op de computer, installeert
u dit programma vanaf de bijgeleverde CD-ROM. (Adobe Reader 6.0)
[Windows]
AdbeRdr60_nld_full.exe
• Adobe Reader 6.0 – Systeemvereisten
[Windows]
• Intel Pentium-processor
• Microsoft Windows 98 Second Edition, Windows Millennium
Edition, Windows NT 4.0 met Service Pack 6, Windows 2000 met
Service Pack 2, Windows XP Professional of Home Edition,
Windows XP Tablet PC Edition
• 32 MB RAM (64 MB aanbevolen)
• 60 MB vrije schijfruimte
• Internet Explorer 5.01, 5.5, 6.0 of 6.1
2. Open het bestand van de gebruiksaanwijzing.
• Open het bestand “DVDA1XV_NEDERLANDS.pdf”.
[Als u de inhoud van de CD-ROM niet kunt bekijken]
• Neem contact op met een van de verkooppunten die staan vermeld
in de bijgevoegde lijst van “Onderhoudscentra”. U zal dan een gedrukt
exemplaar van de gebruiksaanwijzing in de gewenste taal ontvangen.
6
— TABLE OF CONTENTS —
z Features...................................................................................8, 9
x Discs ..........................................................................................10
c Cautions on Handling Discs.......................................................11
v Connections ......................................................................12 ~ 22
b Part Names and Functions................................................23 ~ 26
n Remote Control Unit .........................................................27 ~ 29
m Loading Discs ............................................................................30
, Changing the Default Settings ..........................................31 ~ 56
. Using the Pure Direct Mode................................................57, 58
⁄0 Using the Super Audio CD Setup ..............................................58
⁄1 Adjusting the Picture Quality ............................................59 ~ 62
⁄2 Using the Video Setup ......................................................63 ~ 65
⁄3 Playback ............................................................................66 ~ 70
⁄4 Playing Repeatedly ..............................................................71, 72
⁄5 Playing Tracks in the Desired Order ..........................................73
⁄6 Playing Tracks in the Random Order .........................................74
⁄7 Using the On-screen Display .....................................................75
⁄8 Using the Multiple Audio, Subtitle and Angle Functions ..76 ~ 78
⁄9 Using the Menus .................................................................79, 80
¤0 Marking Scenes you want to see again ....................................81
¤1 Playing in the Zoom Mode ........................................................82
¤2 Playing MP3.........................................................................83, 84
¤3 Playing WMA .............................................................................85
¤4 Playing Still Picture Files (JPEG format)............................86 ~ 88
¤5 Troubleshooting ...................................................................89, 90
¤6 Main Specifications....................................................................91
• ACCESSORIES
Please check to make sure the following items are included with the main unit in the carton:
q
w
e
r
t
y
u
i
o
!0
Audio cord ................................................................................1
Video cord.................................................................................1
Remote control unit (RC-993)...................................................1
R6P/AA batteries ......................................................................3
Power supply cord....................................................................1
w
q
t
DENON LINK cord....................................................................1
IEEE 1394 cord.........................................................................1
CD-ROM (Operating instructions) ............................................1
Operating instructions ..............................................................1
Service station list ....................................................................1
e
y
u
7
r
i
1 FEATURES
1. Newly developed high performance 10 bit I/P converter
performing all processing with a precision of 10 bits
A high precision film/video source detection function not only
makes the DVD-A1XV compatible with 30 frame film sources,
but also achieves high quality images with smooth, natural
pictures and little jaggy noise even when playing images that
presented problems during editing. In addition, a large number
of picture quality adjustment functions, including noise
reduction and digital gamma correction, enables output of not
only progressive but also HDMI/DVI signals, so fine
adjustments can be made according to the display you are
using.
5. HDMI/DVI digital video interface (NOTE 2)
HDMI Ver. 1.1 enables digital transfer of the video and audio
signals of DVD audio discs that are copyright-protected by
CPPM, something that was not possible with HDMI Ver. 1.0.
The DVD-A1XV is HDMI Ver. 1.1 compatible.
(1) HDMI connector
Digital video signals are transferred in Y Cb Cr or RGB.
The audio signals can be transferred simultaneously, so
both audio and video signals can be transferred with a
single cable.
(2) DVI-D connector
Digital video signals are transferred in RGB.
2. Newly developed 10-bit scaler for high definition pixel
conversion
The DVD-A1XV is equipped with a newly developed scaler that
uses an original algorithm to conduct pixel conversion of the
video output signals which have been given optimum
progressive processing with the I/P converter into higher
definition 720P or 1080i signals with 10-bit precision. This in
conjunction with the high performance 10-bit I/P converter
makes for effective high picture quality playback, and enables
output for digital signals via the HDMI/DVI connectors without
reduction in picture quality due to analog conversion.
In addition, the signals are optimized for output to the
independent HDMI and DVI transmitters, so two digital video
signals can be output at the same time.
6. Advanced AL24 Processing
“Advanced AL24 Processing” which greatly increases the
amount of information in the time axis area using unique high
speed signal detection and processing technology for the PCM
signal (CD/DVD) playback circuitry is provided for 2-channel
output. In addition to expansion of data to 24 bits, natural
signal correction without marring the original data is performed
with upconversion sampling.
In addition, DENON’s original analog waveform reproduction
technology, “AL24 Processing PLUS”, is used for the 5.1channel audio output, resulting in high sound quality for all
PCM signal sources.
7. High precision 24-bit D/A converter
The audio playback circuit includes an advanced segment type
D/A converter with the high technical specifications in the
business, manufactured by Burr-Brown, a company with an
established reputation for D/A converters. This high
performance D/A converter allows not only input of the 24bit/192 kHz data of DVD-Audio discs, it also includes an analog
pure FIR filter for ideal DSD playback of Super Audio CDs.
Furthermore, for mixed left and right channel signals, this D/A
converter is used for independent monaural modes for both
the left and right channels, a true luxury enabling playback of
even high quality signals.
3. DPI (DENON Pixel Image) correction function for more
natural outline correction
DENON has developed an outline correction circuit using a
new algorithm that samples the image data of pixels adjacent
to the perceived pixels and processes them. The image is
detected and processed in units of pixels in the vertical,
horizontal and diagonal directions, thereby generating more
natural outlines.
In addition, other processing is performed in ways optimum for
the images, for example brightness signals and color signals
are processed with independent algorithms, ringing that tends
to occur when images are enhanced is restrained, etc.,
thereby achieving more natural images with no reduction in
picture quality.
8. DENON LINK/IEEE1394 digital audio transfer connectors
(1) DENON LINK terminal
This terminal can be used for digital transfer of not only
DVD video signals but also multi-channel audio signals of
DVD audio.
(2) IEEE 1394 terminal
This terminal can be used for digital transfer of not only
DVD video signals, but also DVD audio signals, Super
Audio CD signals and other multi-channel audio signals.
4. 14-bit/216 MHz video D/A converter (NOTE 1)
The DVD-A1XV uses a video D/A converter that conducts D/A
conversion of all video signals at 14 bits and allows 8X
oversampling in the progressive mode to achieve the high
quality picture that DVDs are meant to provide. In addition,
NSV technology reduces noise upon D/A conversion.
9. THX® Ultra Certification, the symbol of excellent high
quality (NOTE 3)
The DVD-A1XV meets THX® Ultra standards, a strict set of
criteria advocated by Lucasfilm on the picture and sound
quality of DVD video players and their operability with
connected equipment. This makes it possible to achieve the
high quality pictures and sound.
8
NOTES:
1. “NSV” is a trademark of Analog Devices, Inc.
2. HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
3. Manufactured under license of Lucasfilm Ltd. Lucasfilm and
THX® Ultra are registered trademarks of Lucasfilm Ltd.
®, HDCD®, High Definition Compatible Digital® and
4.
Microsoft® are either registered trademarks or trademarks of
Microsoft Corporation, Inc. in the United States and/or other
countries. HDCD system manufactured under license from
Microsoft Corporation, Inc. This product is covered by one or
more of the following: In the USA: 5,479,168, 5,638,074,
5,640,161, 5,808,574, 5,838,274, 5,854,600, 5,864,311,
5,872,531, and in Australia: 669114. Other patents pending.
5. Manufactured under license from Dolby Laboratories. “Dolby”
and the double-D symbol are trademarks of Dolby
Laboratories.
6. “DTS” and ”DTS Digital Surround” are registered trademarks
of Digital Theater Systems, Inc.
7. “KODAK” is a trademark of Eastman Kodak Company.
8. “FUJICOLOR CD” is a trademark of Fuji Photo Film Co, Ltd.
9. “Windows Media™”, “Windows®”are a trademarks of
Microsoft Corporation, Inc.
10. Super Audio CD multi-channel playback compatibility
In addition to playing DVD audio and video discs, the DVDA1XV can play multi-channel Super Audio CDs with a playback
frequency range covering 100 kHz and a dynamic range of 120
dB or greater within the audible frequency range, and a
maximum of 5.1 channels can be output.
11. HDCD® (High Definition Compatible Digital®) decoder
(NOTE 4)
HDCD is an encoding/decoding technology that greatly
reduces the distortion occurring at the time of digital recording
while maintaining compatibility with the conventional CD
format. HDCD allows 20-bit data to be converted into the 16bit data of current CDs with no loss in sound quality.
12. Dolby Digital/DTS decoder (NOTE 5, 6)
The DVD-A1XV is equipped with a built-in Dolby Digital/DTS
decoder, allowing you to recreate the atmosphere of a movie
theater or concert hall when using the DVD-A1XV in
combination with an AV amplifier and speakers.
13. Thorough vibration-resistant design
(1) Mechanism using a hybrid loader.
(2) The pickup mechanism is positioned at the center to
reduce the effects of external vibrations.
(3) A heavyweight chassis and low center of gravity make for
a low vibration design.
(4) The six blocks (mechanism + control unit, audio unit, video
unit, digital interface unit, analog power unit and digital
power unit) are structurally isolated, in a design that
eliminates mutual interference.
14. Multiple functions
(1) Still picture playback function
Kodak Picture CD (NOTE 7) and Fujifilm Fujicolor CD
(NOTE 8) can be played on the DVD-A1XV.
Still images stored in JPEG format on CD-R/RWs can also
be played.
(2) Windows Media™ playback function (NOTE 9)
Windows Media™ CDs can be played on the DVD-A1XV.
(3) Multiple audio function
Selection of up to 8 audio languages.
(The number of languages offered differs from DVD to
DVD.)
(4) Multiple subtitle function
Selection of up to 32 subtitle languages.
(The number of languages offered differs from DVD to
DVD.)
(5) Multiple angle function
The angle of view can be changed.
(For DVDs on which multiple angles are recorded.)
(6) GUI (Graphical User Interface) function
The DISPLAY button on the remote control unit can be
used to display player and disc information on the TV
screen.
(7) Marker function
The positions of up to five scenes can be stored in the
memory, so you can watch your favourite scenes
whenever you want.
(8) Playback disable function
This function can be used to disable playback of DVDs you
do not want children to watch.
9
2 DISCS
NOTE:
• This DVD player is designed and manufactured to respond
to the Region Management Information that is recorded on
a DVD disc.
If the Region number described on the DVD disc does not
correspond to the Region number of this DVD player, this
DVD player cannot play this disc.
• The types of discs listed on the table below can be used on the
DVD-A1XV.
The marks are indicated on the disc labels or jackets.
Usable
discs
Recorded
signals
Mark (logo)
DVD video
DVD audio
(NOTE 1)
DVD-R
DVD-RW
(NOTE 2)
Disc size
For European model:
The Region number for this DVD player is 2.
R
Digital audio +
digital video
(MPEG2)
R
R W
For Oceanian, South American model:
The Region number for this DVD player is 4.
RW
DVD+R
(NOTE 2, 3)
DVD+RW
(NOTE 2)
2
12 cm
4
8 cm
DVD+R
DVD+ReWritable
Super
audio CD
Digital audio
12 cm
Video CD
(NOTE 1)
Digital audio +
digital video
(MPEG1)
12 cm
2 Disc terminology
• Groups and tracks (DVD-audios)
DVD-audios are divided into several large sections called
“groups” and smaller sections called “tracks”.
Numbers are allotted to these sections. These numbers are
called “group numbers” and “track numbers”.
8 cm
Digital audio
CD
CD-R
CD-RW
(NOTE 4)
12 cm
Recordable
ReWritable
Group 1
Digital picture
(JPEG)
8 cm
Kodak
Picture CD
JPEG
12 cm
Fujicolor
CD
JPEG
12 cm
WMA
(Windows
Media
Audio)
For example:
MP3
Digital audio
Track 1
Track 2
Group 2
Track 3
Track 1
Track 2
• Titles and chapters (DVD-videos)
DVD-videos are divided into several large sections called
“titles” and smaller sections called “chapters”.
Numbers are allotted to these sections. These numbers are
called “title numbers” and “chapter numbers”.
12 cm
2 The following types of discs cannot be played on the
DVD-A1XV:
• For European model:
DVDs with region numbers other than “2” or “ALL”
For Oceanian, South American model:
DVDs with region numbers other than “4” or “ALL”
• DVD-ROM/RAMs
• CD-ROMs (unless MP3, JPEG, WMA Files)
• CVD/VSDs/SVCD
• CDVs (Only the audio part can be played.)
• CD-Gs (Only the audio is output.)
• Photo CDs
For example:
Title 1
Chapter 1
Chapter 2
Title 2
Chapter 3
Chapter 1
Chapter 2
• Tracks (Super audio CDs, video and music CDs)
Super audio CDs, video and music CDs are divided into
sections called “tracks”.
Numbers are allotted to these sections. These numbers are
called “track numbers”.
NOTE:
1. Some DVD audio, DVD video and video CD discs do not
operate as described in this manual due to the intentions of
the discs’ producers.
2. The DVD-A1XV cannot play DVD-R, -RW, +R and +RW discs
recorded in the “VR” mode or with “CPRM”.
If you wish to play images recorded using a DVD recorder on
the DVD-A1XV, set the DVD recorder to the “Video mode”
(to record in the DVD-Video format) and record on a DVD-R,
-RW, +R or +RW disc.
Discs that have not be finalized cannot be played.
Depending on the disc’s recording status, the disc may not
be accepted or may not be played normally (the picture or
sound may be not be smooth, etc.).
3. DVD+R DL.(Dual Layer) cannot be played.
4. According to recording quality, some CD-R/RW cannot be
played.
For example:
Track 1
Track 2
Track 3
Track 4
Track 5
• Playback control (video CDs)
Video CDs including the words “playback control” on the
disc or jacket are equipped with a function for displaying
menus on the TV screen for selecting the desired position,
displaying information, etc., in dialog fashion.
In this manual, playing video CDs using such menus is
referred to “menu playback”.
Video CDs with playback control can be used on the DVDA1XV.
10
3 CAUTIONS ON HANDLING DISCS
Discs
Cautions on Handling Discs
Only the discs including the marks shown on page 10 can be
played on the DVD-A1XV.
Note, however, that discs with special shapes (heart-shaped
discs, hexagonal discs, etc.) cannot be played on the DVD-A1XV.
Do not attempt to play such discs, as they may damage the
player.
• Do not get fingerprints, grease or dirt on discs.
• Be especially careful not to scratch discs when removing them
from their cases.
• Do not bend discs.
• Do not heat discs.
• Do not enlarge the center hole.
• Do not write on the labeled (printed) side with a ball-point pen
or a pencil.
• Water droplets may form on the surface if the disc is moved
suddenly from a cold place to a warm one. Do not use a
hairdryer, etc., to dry the disc.
Cautions on Storing Discs
Holding Discs
• Always eject discs after playing them.
• Keep discs in their cases to protect them from dust, scratches
and warping.
• Do not put discs in the following places:
1. Places exposed to direct sunlight for long periods of time
2. Humid or dusty places
3. Places exposed to heat from heaters, etc.
Avoid touching the surface of discs when loading and unloading
them.
Be careful not to get
fingerprints on the signal
surface (the side which
shines in rainbow colors).
Cautions on Loading Discs
Cleaning Discs
• Only load one disc at a time. Loading one disc on top of another
may result in damage or scratch the discs.
• Load 8 cm discs securely in the disc guide, without using an
adapter. If the disc is not properly loaded, it may slip out of the
guide and block the disc tray.
• Be careful not to let your fingers get caught when the disc tray
is closing.
• Do not place anything but discs in the disc tray.
• Do not load cracked or warped discs or discs that have been
fixed with adhesive, etc.
• Do not use discs on which the adhesive part of cellophane tape
or glue used to attach the label is exposed, or discs with traces
of tape or labels that have been peeled off. Such discs may get
stuck inside the player, resulting in damage.
2 Fingerprints or dirt on the disc may lower sound and picture
quality or cause breaks in playback. Wipe off fingerprints or
dirt.
2 Use a commercially available disc cleaning set or a soft cloth to
wipe off fingerprints or dirt.
Wipe gently from the middle
outwards.
CAUTIONS ON INSTALLATION
Do not wipe with a circular
motion.
Note:
For heat dispersal, do not install this equipment in a confined
space such as a book case or similar unit.
NOTE:
• Do not use record spray or antistatic. Also do not use
volatile chemicals such as benzene or thinner.
Note
Record
spray
Thinner
Benzene
wall
11
4 CONNECTIONS
NOTES:
• Read the manuals of all the components when making
•
connections.
• Keep the power supply cord unplugged until all connections
•
have been completed.
• If the power is on when connections are made, noise may
•
be generated and damage the speakers.
Be sure to connect the left and right channels properly, L
(left) to L, R (right) to R.
Plug the power supply cord securely into the power outlet.
Incomplete connection may result in noise.
Binding the power supply cord together with connection
cords may result in humming or noise.
(1) Connecting to a TV
• Use the included audio video cord to connect the TV’s video input connector and audio input connectors to the DVD-A1XV’s VIDEO
OUT or S-VIDEO OUT and AUDIO OUT.
S-Video output connector
The video signals are divided into color (C) and brightness (Y) signals, achieving a clearer
picture.
If the TV is equipped with an S-Video input connector, we recommend connecting it to the
DVD-A1XV’s S-Video output connector using a commercially available S-Video connection
cord.
DVD-A1XV
TV
To power outlet
L
R
AUDIO IN
S-VIDEO IN
VIDEO IN
NOTES:
• Connect the DVD-A1XV’s video outputs to the TV either directly or through an AV amplifier. Do not connect it via a VCR (video
cassette recorder). Some discs contain copy prohibit signals. If such discs are played via a VCR, the copy prohibit system may
cause disturbance in the picture.
• Set the “TV TYPE” in “VIDEO SETUP” in “SETUP” to comply with your TV’s video format. When the TV is PAL formatted set to
PAL. (See pages 43, 44.)
• Use the “2ch AUDIO OUT” connectors to connect a TV to the DVD-A1XV. To use with 5.1ch audio output, set “2CH (SRS OFF)” or
“2CH (SRS ON)” under “AUDIO CHANNEL” in “AUDIO SETUP” on the “SETUP” menu to the initial settings. (See pages 46, 47.)
• Set the “TV ASPECT” in “VIDEO SETUP” in “SETUP” to comply with your TV’s aspect. (See page 43.)
• To use with video out or s-video output, set “INTERLACED” in “TV SYSTEM” in “VIDEO SETUP” in “SETUP” at the initial
settings. (See pages 43, 44.)
12
(2) Connecting to a TV or Monitor Equipped with Component Video Input Connectors
Component video output connectors (PR/CR, PB/CB and Y)
The red (PR/CR), blue (PB/CB) and brightness (Y) signals are output independently, achieving more faithful
reproduction of the colors.
• The component video input connectors may be marked differently on some TVs or monitors (PR, PB and Y/RY, B-Y and Y/CR, CB and Y, etc.). For details, refer to the TV’s operating instructions.
• Connect in this way if your TV is compatible with Progressive Scan.
DVD-A1XV
To power outlet
TV
L
R
AUDIO IN
Y
PB/CB PR/CR
COMPONENT VIDEO IN
NOTES:
• Use the three commercially available video cords to connect the DVD-A1XV’s component video output connectors to the TV or
monitor.
• Set the “TV TYPE” in “VIDEO SETUP” in “SETUP” to comply with your TV’s video format. When the TV is PAL formatted set to
PAL. (See pages 43, 44.)
• Set the “COMPONENT VIDEO OUT” in “VIDEO SETUP” in “SETUP” to comply with Progressive TV.
• Use the “2ch AUDIO OUT” connectors to connect a TV to the DVD-A1XV. To use with 5.1ch audio output, set “2CH (SRS OFF)”
or “2CH (SRS ON)” in “AUDIO CHANNEL” in “AUDIO SETUP” in “SETUP” at the initial settings. (See pages 46, 47.)
• Set the “TV ASPECT” in “VIDEO SETUP” in “SETUP” to comply with your TV’s aspect. (See page 43.)
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS
PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525 OR 625 PROGRESSIVE SCAN
PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE “STANDARD DEFINITION”
OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH THIS MODEL 525p AND 625p DVD
PLAYER, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER.
13
(3) Connecting to a TV with 21-pin SCART Terminal
Use the commercially 21-pin SCART cable to connect the TV’s 21-pin SCART terminal to the DVD-A1XV’s 21-pin SCART terminal (AV1).
DVD-A1XV
TV
21-pin SCART terminal
NOTE:
• Some discs contain copy prohibit signals. If such discs are played via a VCR, the copy prohibit system may cause disturbance in
the picture.
• Set the “TV TYPE” in “VIDEO SETUP” in “SETUP” to comply with your TV’s video format. When the TV is PAL formated, set to
PAL. (See pages 43, 44.)
• To improve picture quality, you can change the video signal output from the AV1 terminal from “Video” to either “S-Video” or “RGB”
to suit the type of television you are using (See page 45.).
(4) Connecting to a AV amplifier with a built-in decoder
When DVDs recorded in Dolby Digital or DTS are played, Dolby Digital or DTS bitstream signals are output from the DVD player’s digital
audio output connectors. If a Dolby Digital or DTS decoder is connected, you can achieve sound with the power and sense of presence
of a movie theater or concert hall.
AV amplifier with a built-in decoder
(AV control center)
DVD-A1XV
CH SEL
ENTER
Digital audio input connector
(COAXIAL)
Digital audio input connector
(OPTICAL)
75Ω/ohms pin-plug cable
(commercially available)
(or)
Optical fiber cable
(commercially available)
NOTE:
• Harsh noise that could harm your ears or damage the speakers is generated when a DVD recorded in DTS is played while using
a decoder, etc., that is not DTS-compatible.
2 Connecting an optical fiber cable (commercially available) to the digital audio input connector (OPTICAL)
Dust cap
NOTE:
• Store the dust cap in a safe place, and be careful not to
lose it.
When not using the terminal, attach the cap to protect the
terminal from dust.
Line up in proper direction
Remove the dust cap, line up the cable in the proper directly, then
insert it securely as far as it goes.
14
2 Sound output from the DVD-A1XV’s digital audio output connectors
[ In the case of bitstream output ]
Settings
DIGITAL OUTPUT
Audio recording format
NORMAL
PCM
Dolby Digital
Dolby Digital bitstream
2 channels PCM (48 kHz / 16 bit)
DTS
DTS bitstream
2 channels PCM (48 kHz / 16 bit)
MPEG Audio
2 channels PCM (48 kHz / 16 bit)
2 channels PCM (48 kHz / 16 bit)
DVD video
[ In the case of PCM output ]
Settings
LPCM (44.1 kHz / 48 kHz)
OFF
ON
Audio recording format
DVD video
DVD audio
Copy protection ON
Copy protection OFF
48 kHz / 16 ~ 24 bit
No output data (*1)
48 kHz / 16 ~ 24 bit PCM
48 kHz / 16 bit PCM
96 kHz / 16 ~ 24 bit
No output data
96 kHz / 16 ~ 24 bit PCM
48 kHz / 16 bit PCM
44.1 kHz / 16 ~ 24 bit
No output data (*2)
44.1 kHz / 16 ~ 24 bit PCM
44.1 kHz / 16 bit PCM
48 kHz / 16 ~ 24 bit
No output data (*1)
48 kHz / 16 ~ 24 bit PCM
48 kHz / 16 bit PCM
88.2 kHz / 16 ~ 24 bit
No output data
88.2 kHz / 16 ~ 24 bit PCM
44.1 kHz / 16 bit PCM
96 kHz / 16 ~ 24 bit
No output data
96 kHz / 16 ~ 24 bit PCM
48 kHz / 16 bit PCM
176.4 kHz / 16 ~ 24 bit
No output data
88.2 kHz / 16 ~ 24 bit PCM
44.1 kHz / 16 bit PCM
192 kHz / 16 ~ 24 bit
No output data
96 kHz / 16 ~ 24 bit PCM
48 kHz / 16 bit PCM
Linear PCM
Linear PCM
or
Packed PCM
Video CD
MPEG 1
44.1 kHz / 16 bit PCM
44.1 kHz / 16 bit PCM
Music CD
44.1 kHz / 16 bit Linear PCM
44.1 kHz / 16 bit PCM
44.1 kHz / 16 bit PCM
MP3 CD
MP3 (MPEG-1 Audio Layer 3)
44.1, 48 kHz / 16 bit PCM
44.1, 48 kHz / 16 bit PCM
WMA CD
WMA (Windows Media Audio)
44.1, 48 kHz / 16 bit PCM
44.1, 48 kHz / 16 bit PCM
DSD (DIRECT STREAM DIGITAL)
No output data (*3)
Super audio CD
No output data (*3)
*1 Only 48 kHz/16 bit sources are output.
*2 Only 44.1 kHz/16 bit sources are output.
*3 44.1 kHz/16-bit PCM signals are output during CD layer playback.
• Down-mixed to 2 channels for multi-channel PCM sources. (Only the front left and right channels are output for sources for which
down-mixing is prohibited.)
• When playing copyright-protected linear PCM or packed PCM DVDs, in consideration of copyrights, no digital signals are output for
sources exceeding 48 kHz/16 bits. When playing such sources, either set “LPCM (44.1 kHz/48 kHz)” under “AUDIO SETUP” at
“SETUP” to “ON” (See pages 46, 50.) or make analog connections. (See page 16.)
• When making digital connections to an AV amplifier that is not compatible with 96 kHz/88.2 kHz signals, set “LPCM (44.1 kHz/48 kHz)”
under “AUDIO SETUP” at “SETUP” to “ON”. (See pages 46, 50.)
• With Super audio CDs, digital audio signals cannot be output from the digital out terminals. Use analog or IEEE1394 connections. (See
pages 16, 19, 20.)
• When “DIGITAL OUTPUT : OFF” is selected at the “PURE DIRECT MODE”, digital signals are not output from the digital audio output
at this time.
• Bitstream signals are signals that are compressed and converted into digital format. They are decoded into multi-channel audio signals
(5.1-channel, etc.) by the decoder.
• Linear PCM audio is the signal recording format used for music CDs.
While the signals are recorded at 44.1 kHz/16 bit for music CDs, for DVDs they are recorded at 44.1 kHz/16 bit to 192 kHz/24 bit,
providing higher sound quality than music CDs.
• Packed PCM signals are high sound quality compressed PCM signals that are decompressed with virtually no loss of data.
15
(5) Connecting a basic 5.1-channel surround system
Analog 5.1-channel audio signals can be output from the DVD-A1XV.
The multi-channel audio signals recorded in packed PCM and the multi-channel Super audio CDs can be played when an AV amplifier
equipped with analog 5.1-channel audio inputs is connected.
To power outlet
SURROUND
CENTER
SUBWOOFER
FRONT
DVD-A1XV
CH SEL
ENTER
AV amplifier with 5.1-channel input terminals
NOTES:
• For multi-channel connections, set “AUDIO CHANNEL” under “AUDIO SETUP” at “SETUP” to “MULTI CHANNEL” and make
the “SPEAKER CONFIGURATION”, “CHANNEL LEVEL” and “DELAY TIME” settings. (See pages 46 ~ 51.)
• With the DVD-A1XV, we recommend turning the digital output off by using the “PURE DIRECT MODE” and only outputting
analog signals in order to keep interference from the digital output circuitry to a minimum and allow you to enjoy high-quality
multi-channel sound thanks to the high-bit, high sampling frequency. (See pages 57, 58.)
16
(6) Connecting to a Digital Recorder (MD Recorder, DAT Deck, etc.)
✽ Set the “AUDIO SETUP” default setting as shown below. (See pages 46 ~ 51.)
• “DIGITAL OUTPUT” → “PCM”
“LPCM (44.1kHz/48kHz)” → “ON”
Playing DVDs with incorrect settings may result noise that could damage your ears or the speakers.
DVD-A1XV
B
8
Digital audio input connector
(OPTICAL)
Optical fiber cable
(commercially available)
9
Digital audio input connector
(COAXIAL)
(or)
75Ω/ohms pin-plug cable
(commercially available)
NOTE:
• Digital audio signals cannot be output when playing Super Audio CDs. Use analog connections to record Super Audio CDs.
(7) Connecting to a Stereo Component
DVD-A1XV
Stereo component
NOTE:
• When connecting to a 2-channel audio stereo device using the “5.1ch AUDIO OUT”, set “AUDIO CHANNEL” under “AUDIO
SETUP” on the “SETUP” to “2CH (SRS OFF)” or “2CH (SRS ON)” (See pages 46, 47.). For multi-channel sources, the signals
are down-mixed into two channels (analog).
(Only the front left and right channels are output for sources for which down-mixing is prohibited.)
17
(8) DENON LINK connections
High quality digital sound with reduced digital signal transfer loss can be enjoyed by connecting a separately sold DENON LINK compatible
AV amplifier.
To power outlet
DVD-A1XV
2 DENON LINK S.E. (2nd) settings:
• If you connect the DENON LINK, set to “2nd”.
At “DIGITAL INTERFACE SETUP” under “SETUP”, set “DENON
LINK” to “2nd (AUTO)”, “2nd (1394)” or “2nd (ANALOG)”. (See
pages 38 ~ 41.)
2 DENON LINK Second Edition:
• With the DENON LINK, Second Edition (2nd), the audio signals are
transferred from the DVD player to the AV amplifier in digital form,
with the same quality as the signals recorded on the disc.
• Digital transfer of the high quality multi-channel signals of DVD
audio is possible for all discs.
• When the DENON LINK connection, could be output 176.4kHz,
192kHz/24bit 2ch sources or 96kHz/24bit 6ch sources.
DENON LINK
2 Compatibility with previous models:
• Digital audio signals output from a DENON LINK 2nd compatible
DVD player can only be played on a DENON LINK 2nd compatible
AV amplifier.
AV amplifier with DENON LINK input terminals
NOTES:
• When DENON LINK is set, the down-mixed audio signals are output only from the left and right terminals and front left and front
right terminals. If you want to use the analog terminals, set to “DENON LINK” to “OFF”.
• The DVD-A1XV’s speaker settings are invalidated when the DENON LINK connector is connected. (Make the speaker settings on
the AV amplifier to which the DVD-A1XV is connected.)
• When the DENON LINK 2nd connection, Super Audio CD’s signals are not output from the DENON LINK connector. Please use
the analog audio output terminals or IEEE1394 connectors.
18
(9) IEEE 1394 connections
The simple connection of one IEEE 1394 cable permits high quality digital transfer of the following between devices having IEEE 1394
connectors: the audio of DVD video, DVD audio that up until now could only be connected by 5-conductor audio cable in an analog
connection, or Super Audio CD and other multi-channel audio. (unless DENON LINK connections)
(IEEE 1394 is an international standard established by the Institute of Electrical and Electronics Engineers, Inc. of the U.S.)
To power outlet
DVD-A1XV
IEEE 1394
AV amplifier with IEEE 1394 terminals
2 IEEE1394 settings:
• For IEEE1394 connection, set “IEEE1394” under ”DIGITAL INTERFACE SETUP”at “SETUP” to ”ON”. (See pages 38 ~ 42.)
✽ The DVD-A1XV’s IEEE 1394 mode is designed based on IEEE Std. 1394a-2000, Standard for a High Performance Serial Bus.
✽ IEEE 1394 network
The following types of connections can be made between devices handling IEEE 1394 audio signals (A&M protocol):
q Daisy chain connections
Connect the sets in series using a single IEEE 1394 cord. Up to 15 sets can be connected.
w Tree (tower) connections
Connect the sets in parallel and in series using a single IEEE 1394 cord. Up to 63 sets can be connected.
Copyright Protection System
To play back through an IEEE 1394 connection the audio of Super Audio CD or DVD (except for discs that may be copied freely),
both the player and the amplifier are required to support a copyright protection system called DTCP (Digital Transmission Content
Protection). DTCP is copy protection technology comprising data encryption and the authentication of the remote device. This unit
supports DTCP. Please see the operation manual of your amplifier for information about your amplifier.
19
NOTES:
• Please use the included IEEE 1394 cable. When using a cable other than the included IEEE 1394 cable, please use a 4-pin IEEE
1394 cable with a length of 3.5 m or less for S400 or higher.
• The “IEEE 1394 audio signal (A&M protocol)” output from the DVD-A1XV’s IEEE 1394 connector not out video signals, please
connecting to a TV or Monitor with “component video output” or “S-video output” or “Video output”. (See pages 12 ~ 14.)
• The “IEEE 1394 audio signal (A&M protocol)” output from the DVD-A1XV’s IEEE 1394 connector can only be received on AV
equipment equipped with an IEEE 1394 connector. Digital video (DV), personal computer, and i-Link (a Sony trademark) audio
signals cannot be sent and received. Incorrect connections could lead to malfunction. Connect as instructed in the other device’s
operating manual. Note that there is no guarantee of the operation of the connection even between devices supporting IEEE
1394. Whether or not data and control signals can be transmitted and received between devices supporting IEEE 1394 depends
on the functions of the respective devices.
• When connecting using the IEEE 1394 connector, only connect one cord between the two devices. Never connect two cords
between the two devices (loop connection). If this is done, the signal output from one device will return to the same device,
resulting in malfunction.
• No audio signals are output from the DVD-A1XV’s analog audio connectors, digital audio connectors, DENON LINK and HDMI
connector when IEEE 1394 is set.
To use these connectors, set the IEEE 1394 setting to “OFF”.
• When the IEEE 1394 connector is connected, the DVD-A1XV’s speaker settings are disabled.
• During playback of a device supporting IEEE 1394, please do not disconnect the IEEE 1394 cable of the other device, do not
connect a new device, and do not switch the power on or off. Doing so may interrupt the audio.
• Among the devices that support IEEE 1394, when the power is in the standby mode or off, some devices are not able to relay
data. Please see the operation manual of the connected device that supports IEEE 1394. This unit is not able to relay the IEEE
1394 data while in the standby mode.
• Devices that support IEEE 1394 have the maximum data transfer speed supported by that device marked in the vicinity of the
IEEE 1394 connector. The maximum transfer speed of IEEE 1394 is defined as approximately 100/200/400 Mbps*, with 200
Mbps items having S200 inscribed and 400 Mbps items having S400 inscribed. The maximum IEEE 1394 data transfer speed of
this unit is 400 Mbps. The actual transfer speed may be slower than 400 Mbps when S100 or S200 devices are connected, or
depending on the specifications of the device. Try to ensure that connections are made between devices that have the same
maximum data transfer speed.
* Mbps (Mega bps) is an abbreviation of “Mega bits per second” and indicates the volume of data that can be communicated in 1
second. At 400 Mbps, 400 Mega bits of data is transferred in 1 second.
(10) HDMI connections
A simple 1-cable connection (using a commercially available cable) with a device having an HDMI (High-Definition Multimedia Interface)
connector allows digital transfer of the digital images of and other sources, and the multi-channel sound of DVD video and DVD audio.
The DVD-A1XV is compatible with High-Definition Multimedia Interface (HDMI) Specification Version 1.1. (The multi-channel audio signals
of DVD audio discs can be transferred.) Use Type-A cables that have received HDMI certification for connections to the DVD-A1XV. For
stable signal transfer, we recommend using cables that are a maximum of 5 meters in length.
DVD-A1XV
Monitor equipped with HDMI input connectors
HDMI Input connector
HDMI (TYPE A) cable (commercially available)
20
HDMI settings
• When using HDMI connections, use the HDMI/DVI SELECT button on the main unit or the remote control unit to set “HDMI Y Cb Cr”
or “HDMI R G B”. (See page 63. By default, this setting is set to “HDMI/DVI OFF”.)
Video settings
• Set to “480P/576P” upon shipment from the factory. Can be set manually to change the resolution. Use the HDMI/DVI FORMAT
button on the main unit or the remote control unit to set the resolution to 480P/576P, 720P or 1080i according to the connected
monitor.
Also, when set to “AUTO”, the resolution of the connected HDMI device is detected and the resolution is set automatically.
Audio settings
• When connecting another device with the HDMI connector, make the “HDMI AUDIO SETUP” under “DIGITAL INTERFACE SETUP”
on the “SETUP” according to the specifications of the device or monitor to be connected. (See pages 38 ~ 41.)
Device to be connected
HDMI AUDIO SETUP
HDMI audio
HDMI compatible monitor, projector etc. (2-channel
audio compatible or non-audio compatible)
2 CH
Video signals and 2-channel PCM audio signals are output via
the HDMI connector. When connecting to an AV amplifier with
DENON LINK/IEEE1394 or multi-channel analog audio, set to
“2CH”.
HDMI compatible AV amplifier, monitor, etc. (with
Dolby Digital/DTS decoder)
MULTI
(NORMAL)
Video signals and Dolby Digital/DTS bitstream signals are
output via the HDMI connector.
Make the speaker settings on the connected AV amplifier, etc.
HDMI compatible monitor, etc. (without Dolby
Digital/DTS decoder, with multi-channel audio
compatibility)
MULTI
(LPCM)
Video signals and Dolby Digital/DTS bitstream signals
converted into multi-channel PCM signals are output via the
HDMI connector. Make the speaker settings at “HDMI AUDIO
SETUP” at SETUP.
✽ When set to DENON LINK and IEEE1394, switch the “HDMI AUDIO SETUP” setting to “2CH”.
✽ When the setting for outputting audio signals from the IEEE1394 connector is made, no audio signals are output via the HDMI
connector.
✽ When “MULTI (NORMAL)” “MULTI (LPCM)” is set, analog audio signals are only output from the L/R and FL/FR terminals.
(The signals from the FL/FR terminals are down-mixed audio signals.)
✽ With Super Audio CDs, digital audio signals in areas except for the CD layer are not output via the HDMI connector. To play multichannel/stereo area signals, set the “HDMI AUDIO SETUP” setting to “2CH” and use the analog audio or IEEE1394.
NOTES:
• The HDMI video and audio output are both turned off if the video output is set to “OFF” or if “ALL OFF” is set. (See Pages 57,
58.)
• When selecting MULTI (NORMAL), the DVD-A1XV speaker settings under “AUDIO SETUP”become invalid.
• Among the devices that support HDMI, some devices can control other devices via the HDMI connector; however, the DVD-A1XV
cannot be controlled by another device via the HDMI connector.
• When using display equipment that is not supported by the HDCP (content protection function), the image will not be output
properly.
• The audio signals via the HDMI connector (including the sampling frequency and bit length) may be limited by the equipment that
is connected.
• When using devices not compatible with HDMI specification Ver. 1.1, the audio signals of DVD audio discs copyright-protected
by CPPM are not output via the HDMI connector.
21
(11) DVI-D connections
Connection with equipment that has a DVI (Digital Visual Interface)-D connector permits the transfer of digital images.
✽ When using display equipment that is not supported by the HDCP (content protection function), the image will not be output properly.
✽ Make an audio connection also because an audio signal will not be output via the DVI-D connector.
✽ Commercially DVI cables are available in 24-pin and 29-pin types. The DVD-A1XV supports the 24-pin DVI-D cable, but the 29-pin DVI
cable cannot be connected.
Monitor equipped with DVI-D input connectors
DVD-A1XV
DVI-D Input connector
24P DVI-D cable (commercially available)
DVI-D Settings
• When using DVI-D connections, use the HDMI/DVI SELECT button on the main unit or the remote control unit to set “HDMI Y Cb Cr”
or “HDMI R G B”. (See “HDMI/DVI SELECT” on page 63. By default, this setting is set to “HDMI/DVI OFF”.)
✽ Signals are output via the DVI-D connector in RGB format, regardless of whether “HDMI Y Cb Cr” or “HDMI R G B” is set.
When connecting both the HDMI and DVI-D connectors to monitors
• Video signals with the same resolution are output via the HDMI and DVI-D connectors.
• When monitors are connected to both the HDMI and DVI-D connectors in the AUTO mode, the resolution is set automatically
according to the connected devices. (See “HDMI/DVI FORMAT” on page 63.)
q When two HDMI devices are connected (an HDMI-DVI conversion cable is required)
The resolutions of the two HDMI devices are detected automatically, the lowest resolution is selected and the signals are output
with that resolution.
w When one HDMI and one DVI device are connected
The resolution is set to “480P/576P”.
e When two DVI devices are connected (an HDMI-DVI conversion cable is required)
The resolution is set to “480P/576P”.
It is also possible to set the resolution manually. Use the HDMI/DVI FORMAT button on the main unit or the remote control unit to
set the resolution to “480P/576P”, “720P” or “1080i” according to the resolution of the connected device.
• Select the HDMI output format, either the Y Cb Cr or the RGB format. Use the HDMI/DVI SELECT button on the main unit or the
remote control unit to make the setting. The DVI-D output is set to the RGB format regardless of the HDMI setting. (See page 63.)
Connecting an HDMI-DVI conversion cable
• When connecting to a monitor using a commercially available HDMI-DVI conversion cable, no audio signals are output.
• When connected to a DVI-D compatible monitor, the output is automatically switched to RGB.
• For stable signal transfer, we recommend using cables that are a maximum of 5 meters in length.
Video
Audio
HDMI connector → DVI-D compatible monitor
™
x
Switches automatically to RGB.
DVI-D connector → HDMI compatible monitor
™
x
Output via DVI-D connector in RGB format.
Copyright Protection System
To play the digital images and sounds of DVD video or DVD audio via an HDMI/DVI-D connection, it is necessary that both the player
and monitor (or AV amplifier) support a copyright protection system called HDCP (High-bandwidth Digital Content Protection
System). HDCP is copy protection technology that comprises data encryption and authentication of the partner equipment. The
DVD-A1XV supports HDCP. Please see the user’s manual of your monitor (or AV amplifier) for information about this.
22
5 PART NAMES AND FUNCTIONS
(1) Front Panel
PLAY
OPEN/CLOSE
STOP
STILL / PAUSE
ON / STANDBY
VIDEO MODE
HDMI / DVI
SELECT
FORMAT
SUPER
AUDIO CD
SET UP
PURE
DIRECT
SELECT
PUSH ENTER
DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER
qw e
r
q
Power ON/STANDBY button
w
Power indicator
e
r
t
y
• This indicator lights when the power is on and when the
power is in the standby mode.
Light green : Power is on
Light red : Power is in the standby mode
VIDEO MODE button
• Use this to instantly change the adjustment mode of the
stored video signals. (See page 63.)
The setting values of PICTURE MODE and SQUEEZE
MODE will not be stored.
The unit will return to the stored setting values when the
power is switched off.
• PICTURE MODE
STD
M1
M2
M3
M4
M5
• TV SYSTEM
Power switch
PROGRESSIVE
• Press once to turn the power on.
• Press again to set to the “OFF” position and turn the
power off.
OTHERS
• Information on the disc that is currently playing is shown
on the display. (See page 26.)
OFF
ON
TIME:–30msec
SELECT of HDMI/DVI button
• Press this to set the video signal output via the HDMI/DVI
connector. (See page 63.)
o
HDMI RGB
AUTO
FORMAT of HDMI/DVI button
• Press this to set the video signal format via the HDMI
connector or the DVI connector. (See page 63.)
1080i
TIME:0msec
TIME:+200msec
Select the playback area/layer of SUPER AUDIO
CD (SUPER AUDIO CD SETUP)
• Switch the area /layer of the Super audio CDs played with
priory.
• MULTI.......When playing Super audio CDs, the Multi
channel area is played with priory
• STEREO....When playing Super audio CDs, the stereo
channel area is played with priority.
• CD.............When playing Super audio CDs, the CDs layer
is played with priority.
HDMI/DVI OFF
720P
HDMI/DVI
• AUDIO ADJUST
Remote control sensor
480P/576P
INTERLACED
• SQUEEZE MODE
No effective for interlaced image.
Display
HDMI Y Cb Cr
u
u o
y i
t
i
• Press once to set to the standby mode. The indicator
lights up in red.
• Press again to turn the power on. The indicator lights up in
green.
DVD-A1XV
AUTO
MULTI
23
STEREO
CD
!1 !2
!3 !4
!5
!6 !7 !8 !9 @0 @1 @2
OPEN/CLOSE
PLAY
STOP
STILL / PAUSE
ON / STANDBY
VIDEO MODE
HDMI / DVI
SELECT
FORMAT
SUPER
AUDIO CD
SET UP
PURE
DIRECT
SELECT
PUSH ENTER
DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER
DVD-A1XV
!0
!0
PURE DIRECT SELECT button
• Press to switch the modes with the specific video signals,
digital audio signals and indicate in display on and off. (See
pages 57, 58.)
NORMAL
!1
MODE 1
• This indicator lights when playing the DVD audio or DVD
video.
Super Audio CD indicator
!3
Disc tray
!5
ALL OFF
DVD AUDIO/VIDEO indicator
!2
!4
MODE 2
• This indicator lights when playing the Super Audio CD.
• Load discs here. (See page 30.)
• Press the OPEN/CLOSE button !6 to open and close the
disc tray.
• The disc tray is also closed when the PLAY button !8 is
pressed.
!6
OPEN/CLOSE button (5)
!7
STILL/PAUSE button (3)
!8
PLAY button (1)
!9
STOP button (2)
@0
Skip button (8)
@1
Skip button (9)
@2
Slow/Search buttons (6 7)
DENON LINK indicator
• This indicator lights when the audio signals are transferred
by DENON LINK connections.
Advanced AL24 Processing indicator
• This indicator lights when the audio signals of a DVD, etc.,
are being processed digitally with the Advanced AL24
processing.
24
• Press this to open and close the disc tray.
(See pages 30, 66.)
• Press this to pause images or music or to play images
frame by frame. (See page 68, 69.)
• Press this to play the disc. (See page 67.)
• Press this to stop the disc. (See page 68.)
• Press this to move back to the beginning of the current
track (or chapter).
• Press again to move back to the beginning to the previous
track (or chapter). (See page 69.)
• Press this to move ahead to the beginning of the next
track (or chapter). (See page 69.)
• Press this to set the slow or search play mode.
(See pages 68, 69.)
6: search in the reverse direction.
7: search in the forward direction.
(2) Rear Panel
@3
@4
#0
@5
@6 @7
#1 #2 #3 #4 #5 #6 #7
@3
21-pin SCART terminal (AV1)
@4
Audio output connectors (2ch AUDIO OUT)
@5
Component video output connectors
(COMPONENT VIDEO OUT)
• Connect using a 21-pin SCART cable (available in stores).
• Connect using the included audio cord.
Multi-channel sound is down-mixed and output.
• Connect using video cords (available in stores).
@6
• Connect using an S-Video connection cord (available in
stores).
Video output connector (VIDEO OUT)
@8
HDMI output connector (HDMI)
Control connector (RS-232C)
#3
Control input connector (ROOM TO ROOM IN)
#4
Control output connector (ROOM TO ROOM OUT)
#5
Digital output connector (DENON LINK)
#6
Digital audio output connector (OPTICAL)
#7
Digital audio output connector (COAXIAL)
• Connect using the included video cord.
• Connect using HDMI (TYPE A) connection cord (available
in stores).
DVI-D-Video output connector (DVI-D OUT)
• Connect using 24P DVI-D connection cord (available in
stores).
#0
Audio output connectors (5.1ch AUDIO OUT)
#1
Digital connectors (IEEE 1394)
• Connect using an audio cord. Connect a commercially
available pin-plug cord.
#8
• This is for connection of a separately sold AV amplifier
equipped with a IEEE 1394 connector.
• Use it to achieve high quality digital sound with low data
loss.
25
#8
#2
S-Video output connector (S-VIDEO OUT)
@7
@9
@8 @9
• This is a terminal for future system expansion.
• This is the input connector for wired remote control.
Consult your DENON dealer if you wish to use this
connector.
• This is the output connector for wired remote control.
Consult your DENON dealer if you wish to use this
connector.
• This is for connection of a separately sold AV amplifier
equipped with a DENON LINK connector.
• Use it to achieve high quality digital sound with low data
loss.
• Connect using an optical fiber cable (available in stores).
• Digital data is output from this connector.
• Connect using an digital audio cord. Connect a
commercially available 75 Ω/ohms pin-plug cord.
• Digital data is output from this connector.
Power input (AC IN)
• Connect to AC power supply using the included power
supply cord.
(3) Display
q w
e
r t yu
i
SUPER DVD GROUP TITLE TRACK CHAP ANGLE D.MIX PROG RAND TOTAL SING
AUDIO VCD
1 A-B
PROGRESSIVE
FV
!3 !4
q
w
e
r
t
y
u
i
o
!0
!1
!2
o !0
REM HDCD
!1
DIGITAL
L.PCMP.PCM L
MPEG JPEG SL
WMA MP3 HDMI
IEEE1394 DVI
!2
C R LFE
S SR
!6 !7
!5
!3
Lights to indicate the currently playing disc.
Lights in the repeat play mode.
These light to indicate the names of sections of the disc
being played.
!4
!5
Lights during playback of multiple angles disc.
Lights when the audio signals can be down-mixed.
!6
Lights in the programmed play mode.
!7
Lights in the random play mode.
There light to indicate the time display mode.
Lights when HDCD is playing.
Lights when SRS TruSurround is on.
Lights to indicate the currently playing audio format.
Lights to indicate the currently playing audio.
L : Front left channel
C : Center channel
R : Front right channel
SL : Surround left channel
S : Mono surround channel
SR : Surround right channel
LFE : Low frequency effect
26
Lights to indicate the currently playing video type.
F :Film source
V :Video source
Lights when progressive video signals are being output.
Displays the title , track number and elapsed time during
playback.
Lights when the audio signals is output from IEEE1394
terminals.
Lights when the video (or audio) signals is output via HDMI
or DVI connectors.
(Flashes while the connection to the HDMI/DVI-D connector
is being checked.)
6 REMOTE CONTROL UNIT
2 The DVD-A1XV can be controlled from a distance using the included remote control unit (RC-993).
(1) Inserting Batteries
q Remove the remote control unit’s rear cover.
Cautions On Batteries
• Use R6P/AA batteries in this remote control unit.
• Replace the batteries with new ones approximately once
a year, though this depends on the frequency with which
the remote control unit is used.
• If the remote control unit does not operate from close to
the main unit, replace the batteries with new ones, even
if less than a year has passed.
• The included battery is only for verifying operation.
Replace it with a new battery as soon as possible.
• When inserting the batteries, be careful to do so in the
proper direction, following the < and > marks in the
remote control unit’s battery compartment.
• To prevent damage or battery fluid leakage:
• Do not use a new battery with an old one.
• Do not use two different types of batteries.
• Do not short-circuit, disassemble, heat or dispose of
batteries in flames.
• Remove the batteries when not planning to use the
remote control unit for a long period of time.
• If the batteries should leak, carefully wipe off the fluid
from the inside of the battery compartment, then insert
new batteries.
w Place three R6P/AA batteries in the battery compartment in
the direction indicated by the marks.
e Close the rear cover.
(2) Using the Remote Control Unit
• When operating the remote control unit, point it at the remote
control sensor as shown on the diagram.
• The remote control unit can be used from a direct distance of
approximately 7 meters. This distance will be shorter, however,
if there are obstacles in the way or if the remote control unit is
not pointed directly at the remote control sensor.
• The remote control unit can be operated at a horizontal angle of
up to 30° with respect to the remote control sensor.
Approx. 7 meters
NOTES:
• It may be difficult to operate the remote control unit if the
remote control sensor is exposed to direct sunlight or
strong artificial light.
• Do not press buttons on the main unit and on the remote
control unit at the same time. Doing so will result in
malfunction.
30°
30°
27
(3) Names and Functions of Remote Control Unit Buttons
2 Button not explained here function in the same way as the corresponding buttons on the main unit.
POWER OFF
POWER ON/POWER OFF buttons
w
HDMI/DVI SELECT/FORMAT buttons
e
Number buttons
r
LIGHT button
t
ANGLE button
y
TOP MENU button
u
Cursor buttons/ENTER button
i
MENU button
o
!0
!1
!2
STOP button (2)
!3
A-B repeat button (A-B)
!4
RANDOM button
!5
MARKER button
!6
SETUP button
!7
PICTURE ADJUST button
POWER ON
q
w
q
HDMI/DVI
SELECT
e
CLEAR
ANGLE
CALL
SUBTITLE
AUDIO
TOP MENU
DISPLAY
MENU
!0
!1
!3 !2
!5 !4
!6
!7
SEARCH MODE
BACK LIGHT
RETURN
STOP
• Use these to input numbers.
Use the +10 button to input numbers of 10 or over.
Example : To input 25
NTSC/PAL
PROGRAM
/DIRECT
o
• Use these to select to use HDMI connector or DVI
connector, and the format of video signals (480P/576P,
720P, 1080i, AUTO).
OPEN/
CLOSE
FORMAT
SUPER AUDIO
CD SETUP
r
t
y
u
i
• Press this to switch the power between on and standby.
STILL/PAUSE
SKIP
PLAY
SLOW/SEARCH
PAGE
REPEAT
A-B
RANDOM
MARKER
ZOOM
SETUP
PICTURE
ADJUST
PICT ADJ.
MEMORY
DIMMER
PURE DIRECT
SELECT
RC-993
28
• Press this to light the all buttons.
Press again this to put out light.
• Press this to switch the angle.
• The top menu stored on the disc is displayed.
• Use the • and ª cursor buttons to select in the vertical
direction.
Use the 0 and 1 cursor buttons to select in the horizontal
direction.
Press the ENTER button to select the item selected with
the cursor buttons.
• The DVD menu stored on the disc is displayed.
STILL/PAUSE button (3)
SKIP buttons
REPEAT button
• Press this to play tracks repeatedly.
• Use this to repeat sections between two specific points.
• Press this to play the tracks on the video or music CD in
random order.
• Press this to mark places you want to see again.
• Press this to display the default setting screen.
• Press this to adjust the picture quality to suit your tastes.
POWER OFF
POWER ON
HDMI/DVI
SELECT
OPEN/
CLOSE
FORMAT
NTSC/PAL
SUPER AUDIO
CD SETUP
PROGRAM
/DIRECT
CLEAR
SEARCH MODE
CALL
BACK LIGHT
ANGLE
SUBTITLE
AUDIO
TOP MENU
DISPLAY
MENU
RETURN
STOP
STILL/PAUSE
SKIP
PLAY
SLOW/SEARCH
PAGE
REPEAT
A-B
RANDOM
MARKER
SETUP
PICTURE
ADJUST
PICT ADJ.
ZOOM
DIMMER
PURE DIRECT
MEMORY
SELECT
!9
!8
@0
@1
@2
@3 @4
@5 @6
@7
@8
@9
#0
#1
#2
#3
#4
RC-993
29
!8
!9
OPEN/CLOSE button
@0
@1
@2
SUPER AUDIO CD SETUP button
@3
CALL button
@4
SEARCH MODE button
@5
AUDIO button
@6
SUBTITLE button
@7
DISPLAY button
@8
RETURN button
@9
#0
#1
PLAY button (1)
#2
ZOOM button
#3
DIMMER button
#4
PURE DIRECT MEMORY/SELECT buttons
NTSC/PAL button
• Use this to switch the set’s video output format
(NTSC/PAL).
PROGRAM/DIRECT button
CLEAR button
• Press this to clear numbers that you have input.
• Press this to check the program contents.
• Press this to change the search mode to search for groups
or titles, tracks or chapters when selecting sections of
discs directly using the number buttons.
• For DVDs, press this to switch the audio language. For
video CDs, press this to switch the channel between
“STEREO”, “MONO LEFT” and “MONO RIGHT”.
• Press this to switch the DVD’s subtitle language.
• Press this to display the ON-SCREEN.
• Press this to return to the previous menu screen.
SLOW/SEARCH buttons
PAGE –/PAGE + buttons
• Use these to selected the desired still picture on DVD
audio discs containing browseable still pictures.
• Press this to enlarge the image.
• Use this to adjust the brightness of the main unit’s display.
Can be switched in 4 steps, from all off to always on.
• Use these to make and select that various setting to
achieve higher quality sound.
7 LOADING DISCS
2 Set discs in the disc tray with the labeled (printed) side facing up.
(2) Loading Discs
• Pick up the disc carefully so as not to touch the signal surface
and hold it with the labeled side facing up.
• With the disc tray fully open, set the disc in the disc tray.
• Set 12 cm discs in the outer disc guide (Figure 1), 8 cm discs in
the inner disc guide (Figure 2).
• Press the OPEN/CLOSE button. The disc is automatically
loaded.
• The disc tray can also be closed automatically to load the disc
by pressing the PLAY button.
Outer disc guide
(12 cm disc)
Inner disc guide
(8 cm disc)
Disc tray
Figure 1
NOTE:
• Do not move the DVD-A1XV while a disc is playing. Doing
so may scratch the disc.
Outer disc guide
(1) Opening and Closing the Disc Tray
q Turn on the power.
w Press the OPEN/CLOSE button.
12 cm disc
Power switch
Figure 2
OPEN/CLOSE button
Inner disc guide
Disc tray
8 cm disc
NOTES:
• Be sure to turn on the power before opening and closing
the disc tray.
• Do not strike on the button with a pencil, etc.
NOTES:
• If a foreign object is caught in the disc tray during closing,
simply press the OPEN/CLOSE button again and the tray
will open.
• Do not press the disc tray in by hand when the power is
off. Doing so will damage it.
• Do not place foreign objects in the disc tray. Doing so will
damage it.
30
8 CHANGING THE DEFAULT SETTINGS
2 Make the initial settings to suit your usage conditions before starting playback.
The initial settings are retained until they are next changed, even if the power is turned off.
POWER OFF
POWER ON
1
HDMI/DVI
SELECT
FORMAT
OPEN/
CLOSE
NTSC/PAL
SUPER AUDIO
CD SETUP
OPEN/CLOSE
PLAY
PROGRAM
/DIRECT
STOP
CLEAR
SEARCH MODE
CALL
STILL / PAUSE
BACK LIGHT
ANGLE
ON / STANDBY
SUBTITLE
AUDIO
VIDEO MODE
HDMI / DVI
SELECT
FORMAT
SUPER
AUDIO CD
SET UP
PURE
DIRECT
SELECT
TOP MENU
DISPLAY
MENU
RETURN
PUSH ENTER
DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER
1
3
DVD-A1XV
1
2
(Green)
1
Turn on the power.
• Press the power button, the power indicator lights green and the
power turns on.
When pressed again, the power turns off and indicator is off.
• In the standby mode (the power indicator lights red), press the
ON/STANDBY button on the main unit or POWER ON button on the
remote control unit (RC-993).
PICTURE
ADJUST
PICT ADJ.
PURE DIRECT
MEMORY
SELECT
ON / STANDBY
Main unit
(Red)
ON / STANDBY
POWER ON
Main unit
31
SETUP
Remote control unit
In the stop mode, press the SETUP button.
• The setup (default settings) screen appears.
NOTE: For some menus, the initial values can be changed during
playback.
SETUP
LANGUAGE SETUP
Use this to set the language to be used when playing the disc. If the set
language is not offered on that disc, the discs default language is set.
And use this to set the language for the default setting screen and
messages displayed on the TV screen (“PLAY”, etc.).
Remote control unit
DIGITAL INTERFACE SETUP
2
Use this to set the output of DVI, HDMI, DENON LINK and IEEE1394
terminals.
L ANGUAGE SE TUP
D I AL OG
ENGL I SH
SUBT I T L E
ENGL I SH
D I SC MENUS
ENGL I SH
Use this to set the DVD-A1XV’s screen mode.
OSD LANGUAGE
ENGL I SH
AUDIO SETUP
E X I T SE TUP
VIDEO SETUP
Use this to set the DVD-A1XV’s audio output mode.
RATINGS
Use this to disable playback of adult DVDs so that children cannot watch
them. Note that playback of adult DVDs cannot be disabled if the rating
level is not recorded on the DVD.
SE L ECT :
DEC I S I ON : ENTER BUT TON
OTHER SETUP
These include special settings such as CAPTIONS, WALL PAPER , etc,.
Use the 0 and 1 cursor buttons to select the desired setting item, then
press the ENTER button.
• Select “LANGUAGE SETUP”. (See pages 35 ~ 37.)
• Select “DIGITAL INTERFACE SETUP”. (See pages 38 ~ 42.)
3
• Select “VIDEO SETUP”. (See pages 43 ~ 45.)
• Select “AUDIO SETUP”. (See pages 46 ~ 51.)
Remote control unit
• Select “RATINGS”. (See pages 52, 53.)
Remote control unit
• Select “OTHER SETUP”. (See pages 54 ~ 56.)
✽ To exit the setup mode
Use the ª cursor button to select “EXIT SETUP”, then press the ENTER button. It is also possible to quit by pressing the SETUP
button on the remote control unit.
32
Setup items for use
Bold characters indicate factory defaults.
LANGUAGE SETUP
DIALOG
SUBTITLE
DISC MENUS
ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
OTHERS
OFF
ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
OTHERS
The display depends on the connected device.
SPEAKER
CONFIGURATION
FRONT SP
CENTER SP
ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
OTHERS
SUBWOOFER
SURROUND SP
CROSSOVER
OSD LANGUAGE
ENGLISH
FRANÇAIS
ESPAÑOL
DEUTSCH
DIGITAL INTERFACE SETUP
HDMI/DVI
NORMAL
PICTURE ADJUST
ENHANCED
(without HDMI Y Cb Cr)
CHANNEL LEVEL
HDMI
AUDIO SETUP
2CH
MULTI (NORMAL)
MULTI (LPCM)
HDMI SPEAKER SETUP
HDMI
AUTO FORMAT
PANEL RES.
MAX RES.
DENON LINK
OFF
2nd (AUTO)
2nd (1394)
2nd (ANALOG)
IEEE1394
OFF
ON
VIDEO SETUP
TV ASPECT
IEEE1394 SETUP
AUDIO FORMAT
4:3 PS
4:3 LB
WIDE (16:9)
TV TYPE
NTSC
PAL
MULTI
TV SYSTEM
PROGRESSIVE
INTERLACED
HDMI/DVI
OTHERS
COMPONENT
VIDEO OUT
PROGRESSIVE
INTERLACED
SQUEEZE MODE
OFF
ON
AUTO
PROGRESSIVE
MODE
AUTO
VIDEO1
VIDEO2
AV1 VIDEO MODE
VIDEO
S-VIDEO
RGB
FRONT LCH
CENTER
FRONT RCH
SURROUND RCH
SURROUND LCH
SUBWOOFER
DELAY TIME
AUTO PLAY
33
TEST TONE
OFF
ON
FORMAT1
FORMAT2
DISTANCE
FRONT LCH
FRONT RCH
CENTER
SURROUND LCH
SURROUND RCH
SUBWOOFER
DEFAULT
LARGE
SMALL
LARGE
SMALL
NONE
YES
NO
LARGE
SMALL
NONE
40Hz
60Hz
80Hz
100Hz
120Hz
OFF
AUTO
MANUAL
0 dB
0 dB
0 dB
0 dB
0 dB
0 dB
METERS
FEET
3.6m
3.6m
3.6m
3.0m
3.0m
3.6m
ON
Bold characters indicate factory defaults.
AUDIO SETUP
AUDIO CHANNEL
DIGITAL OUTPUT
MULTI CHANNEL
2 CH (SRS OFF)
2 CH (SRS ON)
OFF
ON
SOURCE DIRECT
OFF
ON
BASS ENHANCER
OFF
ON
SACD FILTER
RATINGS
RATING LEVEL
PASSWORD
OTHER SETUP
PLAYER MODE
SUBWOOFER
SURROUND SP
CROSSOVER
CHANNEL LEVEL
OFF
ON
0 (LOCK ALL)
1
2
3
4
5
6
7
8 (NO LIMIT)
DELAY TIME
OLD PASSWORD
NEW PASSWORD
CONFIRM PASSWORD
AUDIO
VIDEO
CAPTIONS
OFF
ON
WALL PAPER
BLUE
GRAY
BLACK
PICTURE
SCREEN SAVER
OFF
ON
DISPLAY
OFF
ON
AUTO POWER
MODE
OFF
ON
SLIDE SHOW
5SEC
(5~15SEC)
TEST TONE
FRONT LCH
CENTER
FRONT RCH
SURROUND RCH
SURROUND LCH
SUBWOOFER
SW+10dB
50kHz
100kHz
CHANGE
FRONT SP
CENTER SP
NORMAL
PCM
LPCM
(44.1 kHz/48 kHz)
COMPRESSION
SPEAKER SETUP
SPEAKER
CONFIGURATION
34
DISTANCE
FRONT LCH
FRONT RCH
CENTER
SURROUND LCH
SURROUND RCH
SUBWOOFER
DEFAULT
LARGE
SMALL
LARGE
SMALL
NONE
YES
NO
LARGE
SMALL
NONE
40Hz
60Hz
80Hz
100Hz
120Hz
OFF
AUTO
MANUAL
0 dB
0 dB
0 dB
0 dB
0 dB
0 dB
OFF
ON
METERS
FEET
3.6m
3.6m
3.6m
3.0m
3.0m
3.6m
ON
When “LANGUAGE SETUP” is selected
1
See pages 31, 32.
Use the • and ª cursor buttons to select the desired setting, then press
the ENTER button.
DIALOG
Use this to set the language of the sound output from the speakers.
2
SUBTITLE
Use this to set the language of the subtitles displayed on the TV.
DISC MENUS
Use this to set the language of the menus recorded on the disc (top
menu, etc.).
OSD LANGUAGE
Use this to set the language for the default setting screen and
messages displayed on the TV screen (“PLAY”,etc.)
Remote control unit
Remote control unit
L ANGUAGE SE TUP
D I AL OG
ENGL I SH
SUBT I T L E
ENGL I SH
D I SC MENUS
ENGL I SH
OSD LANGUAGE
ENGL I SH
E X I T SE TUP
SE L EC T :
DE C I S I ON : ENTER BUT TON
Use the • and ª cursor buttons to select the desired setting, then press
the ENTER button.
3
q When “DIALOG” is selected:
ENGLISH (Factory default)
Select this when you want to play the DVD with the sound in English.
FRENCH
Select this when you want to play the DVD with the sound in French.
SPANISH
Select this when you want to play the DVD with the sound in Spanish.
GERMAN
Select this when you want to play the DVD with the sound in German.
ITALIAN
Select this when you want to play the DVD with the sound in Italian.
OTHERS
Use the number buttons to input the language number.
(See “Language code list” on page 37.)
Remote control unit
L ANGUAGE SE TUP
D I AL OG
SUBT I T L E
D I SC MENUS
OSD LANGUAGE
ENGL I SH
F RENCH
SPAN I SH
GERMAN
I TAL I AN
E X I T SE TUP
SE L EC T :
35
Remote control unit
OTHERS
DE C I S I ON : ENTER BUT TON
w When “SUBTITLE” is selected:
OFF
Select this if you do not want to display the subtitles. (For some discs
it is not possible to turn off the subtitle display.)
ENGLISH (Factory default)
Select this when you want to play the DVD with the subtitles in
English.
FRENCH
Select this when you want to play the DVD with the subtitles in
French.
SPANISH
Select this when you want to play the DVD with the subtitles in
Spanish.
GERMAN
Select this when you want to play the DVD with the subtitles in
German.
ITALIAN
Select this when you want to play the DVD with the subtitles in
Italian.
OTHERS
Use the number buttons to input the language number.
(See “Language code list” on page 37.)
3
e When “DISC MENUS” is selected:
ENGLISH (Factory default)
Select this when you want to display the menus in English.
FRENCH
Select this when you want to display the menus in French.
SPANISH
Select this when you want to display the menus in Spanish.
GERMAN
Select this when you want to display the menus in German.
ITALIAN
Select this when you want to display the menus in Italian.
OTHERS
Use the number buttons to input the language number.
(See “Language code list” on page 37.)
Remote control unit
Remote control unit
L ANGUAGE SE TUP
D I AL OG
SUBT I T L E
D I SC MENUS
OSD LANGUAGE
OF F
ENGL I SH
F RENCH
SPAN I SH
E X I T SE TUP
GERMAN
I TAL I AN
OTHERS
SE L EC T :
DE C I S I ON : ENTER BUT TON
L ANGUAGE SE TUP
D I AL OG
SUBT I T L E
D I SC MENUS
OSD LANGUAGE
ENGL I SH
F RENCH
SPAN I SH
E X I T SE TUP
GERMAN
I TAL I AN
OTHERS
SE L EC T :
DE C I S I ON : ENTER BUT TON
L ANGUAGE SE TUP
D I AL OG
r When “OSD LANGUAGE” is selected:
ENGLISH (Factory default)
Select this to set the OSD language to English.
FRANÇAIS
Select this to set the OSD language to French.
ESPAÑOL
Select this to set the OSD language to Spanish.
DEUTSCH
Select this to set the OSD language to German.
SUBT I T L E
D I SC MENUS
OSD LANGUAGE
ENGL I SH
FRANÇAIS
E X I T SE TUP
ESPAÑOL
DEUTSCH
SE L EC T :
DE C I S I ON : ENTER BUT TON
✽ To exit the setup mode
Use the ª cursor button to select “EXIT SETUP”, then press the ENTER button. It is also possible to quit by pressing the SETUP
button on the remote control unit.
36
Language code list
Code
Language
Code
Code
Language
Language
Code
Language
6565
Afar
7079
Faroese
7678
Lingala
8375
Slovak
6566
Abkhazian
7082
French
7679
Laothian
8376
Slovenian
6570
Afrikaans
7089
Frisian
7684
Lithuanian
8377
Samoan
6577
Ameharic
7165
Irish
7686
Latvian, Lettish
8378
Shona
6582
Arabic
7168
Scots Gaelic
7771
Malagasy
8379
Somali
6583
Assamese
7176
Galician
7773
Maori
8381
Albanian
6588
Aymara
7178
Guarani
7775
Macedonish
8382
Serbian
6590
Azerbaijani
7185
Gujarati
7776
Malayalam
8385
Sundanese
6665
Bashkir
7265
Hausa
7778
Mongolian
8386
Swedish
6669
Byelorussian
7273
Hindi
7779
Moldavian
8387
Swahili
6671
Bulgarian
7282
Croatian
7782
Marathi
8465
Tamil
6672
Bihari
7285
Hungarian
7783
Malay
8469
Telugu
6678
Bengali; Bangla
7289
Armenian
7784
Maltese
8471
Tajik
6679
Tibetan
7365
Interlingua
7789
Burmese
8472
Thai
6682
Breton
7378
Indonesian
7865
Nauru
8473
Tigrinya
6765
Catalan
7383
Icelandic
7869
Nepali
8475
Turkmen
6779
Corsican
7384
Italian
7876
Dutch
8476
Tagalog
6783
Czech
7387
Hebrew
7879
Norwegian
8479
Tonga
6789
Welsh
7465
Japanese
7982
Oriya
8482
Turkish
6865
Danish
7473
Yiddish
8065
Panjabi
8484
Tatar
6869
German
7487
Javanese
8076
Polish
8487
Twi
6890
Bhutani
7565
Georgian
8083
Pashto, Pushto
8575
Ukrainian
6976
Greek
7575
Kazakh
8084
Portuguese
8582
Urdu
6978
English
7576
Greenlandic
8185
Quechua
8590
Uzbek
6979
Esperanto
7577
Cambodian
8277
Rhaeto-Romance
8673
Vietnamese
6983
Spanish
7578
Kannada
8279
Romanian
8679
Volapük
6984
Estonian
7579
Korean
8285
Russian
8779
Wolof
6985
Basque
7583
Kashmiri
8365
Sanskrit
8872
Xhosa
7065
Persian
7585
Kurdish
8368
Sindhi
8979
Yoruba
7073
Finnish
7589
Kirghiz
8372
Serbo-Croatian
9072
Chinese
7074
Fiji
7665
Latin
8373
Singhalese
9085
Zulu
37
When “DIGITAL INTERFACE SETUP” is selected
1
See pages 31, 32.
Use the • and ª cursor buttons to select the desired setting, then press
the ENTER button.
HDMI/DVI PICTURE ADJUST
Switches the digital RGB video range (data range) via the HDMI and the
DVI-D connectors.
Remote control unit
Remote control unit
HDMI AUDIO SETUP
2
Use this to adjust for the audio signals via the HDMI connector.
D I G I T A L I NTERF ACE SE T UP
HDM I/ DV I P I C T UR E ADJ US T
HDMI AUTO FORMAT
Set the “AUTO” function selected with the HDMI/DVI FORMAT button
on the main unit or the remote control unit.
DENON LINK
Use this to output digital signals from the DENON LINK terminal.
NORMAL
HDM I AUD IO SE TUP
2CH
HDM I AUTO FORMAT
PANE L R E S .
D ENON L INK
OF F
I E E E1394
OF F
E X I T SE TUP
IEEE1394
Use this to output digital signals from the IEEE1394 terminal.
SE L EC T :
DE C I S I ON : ENTER BUT TON
Use the • and ª cursor buttons to select the desired setting, then press
the ENTER button.
3
q When “HDMI/DVI PICTURE ADJUST” is selected:
NORMAL (Factory default)
Signals are output via the HDMI and the DVI-D connectors with a
digital RGB video range (data range) of 16 (black) to 235 (white).
ENHANCED
Signals are output via the HDMI and the DVI-D connectors with a
digital RGB video range (data range) of 0 (black) to 255 (white).
When the HDMI and the DVI-D connectors are connected , the black
may seem to stand out, depending on the TV or the Monitor. In this
case, set this to “ENHANCED”.
When select “HDMI Y Cb Cr” under “HDMI/DVI SELECT”, will have
no effect. (See page 63.)
Remote control unit
D I G I TA L I NTERF ACE SE T UP
HDM I/ DV I P I C T UR E ADJ US T
HDM I AUD IO SE TUP
NORMAL
ENHANCED
HDM I AUTO FORMAT
D E NO N L INK
I E E E1394
E X I T SE TUP
SE L EC T :
38
Remote control unit
DE C I S I ON : ENTER BUT TON
w When “HDMI AUDIO SETUP” is selected:
2CH (Factory default)
The audio signals are output via the HDMI connector with a downmixed to 2 channel.
MULTI (NORMAL)
The multi-channel audio signals are output via the HDMI connector
with a bitstream.
MULTI (LPCM)
The multi-channel audio signals are output via the HDMI connector
with a linear PCM.
Remote control unit
Remote control unit
D I G I T A L I NTERF ACE SE T UP
HDM I/ DV I P I C T UR E ADJ US T
B When “MULTI (LPCM)” is selected, use the • and ª cursor
buttons to select the item to be set, then press the ENTER button.
SPEAKER CONFIGURATION
Use this to select the types of the different speakers.
CHANNEL LEVEL
Use this to adjust the output level of the different speakers.
DELAY TIME
Use this to set the distance from the different speakers to the
listening position.
3
✽ To exit the HDMI SPEAKER SETUP mode.
Use the ª cursor button to select “DIGITAL INTERFACE SETUP”
then press ENTER button.
HDM I AUD IO SE TUP
2CH
HDM I AUTO FORMAT
MULTI(NORMAL)
D E NO N L INK
MULTI(LPCM)
I E E E1394
E X I T SE TUP
SE L EC T :
DE C I S I ON : ENTER BUT TON
HDMI SPE AKE R SE TUP
SPE AKER CONF I GURAT I ON
CHANNE L L E VE L
DE L AY T I ME
B When “SPEAKER CONFIGURATION” is selected, use the • and
ª cursor buttons to select the speaker to be set then press the
ENTER button.
• The type of speaker used for the front speakers, center speaker,
subwoofer and surround speakers can be set. Use the • and ª
cursor buttons to select the speaker type, then press the
ENTER button.
LARGE
Select this when a large speaker is connected.
SMALL
Select this when a small speaker is connected.
DIGITAL INTERFACE SETUP
SE L EC T :
DE C I S I ON : ENTER BUT TON
HDMI SPE AKE R SE TUP
SPE AKER CONF I GURAT I ON
• When “CROSSOVER” is selected:
40 Hz, 60 Hz, 80 Hz (Factory default), 100 Hz, 120 Hz, set the
frequency of cross over.
F RONT SP
L ARGE
CENT ER SP
L ARGE
SUBWOOF ER
SURROUND SP
CROSSOVE R
YES
L ARGE
80Hz
✽ Press the RETURN button to return to the “HDMI SPEAKER
SETUP” menu.
SE L EC T :
DE C I S I ON : ENTER BUT TON
The display depends on the connected device.
(Indicates whether or not speakers are
connected)
39
B When “CHANNEL LEVEL” is selected, use the • and ª cursor
buttons to select the speaker to be adjusted, then use the 0 and
1 cursor buttons to set the level.
• TEST TONE
Use the 0 and 1 cursor buttons to select auto or manual.
Adjust so that the volume of the test tones output from the
different speakers sounds the same.
• The volume level output from the front speakers (left and right
channels), center speaker, surround speakers (left and right
channels) and subwoofer can be adjusted.
• The volume level can be adjusted between 0 and –10 dB in
steps of 1 dB.
Remote control unit
Remote control unit
HDMI SPE AKE R SE TUP
CHANNEL LEVEL
✽ Press the RETURN button to return to the “HDMI SPEAKER
SETUP” menu.
SE L EC T :
T E ST TONE
OF F
F RONT L CH
0 dB
CENT ER
0 dB
F RONT RCH
0 dB
SURROUND RCH
0 dB
SURROUND LCH
0 dB
SUBWOOF ER
0 dB
DE C I S I ON : ENTER BUT TON
HDMI SPE AKE R SE TUP
3
DELAY TIME
B When “DELAY TIME” is selected:
With 5.1-channel surround sound, ideally the distance between
the listening position and all the speakers aside from the
subwoofer should be the same. The delay time setting can be
used to make the sound from the different speakers reach the
listening position at the same time.
METERS
D I STANC E
F RONT L CH
3.6 m
F RONT RCH
3.6 m
CENT ER
3.6 m
SURROUND L CH
3.0 m
SURROUND R CH
3.0 m
SUBWOOF ER
3.6 m
ON
DE F AUL T
SE L EC T :
DE C I S I ON : ENTER BUT TON
Use the • and ª cursor buttons to select the setting item, then
press the ENTER button.
HDMI SPE AKE R SE TUP
DELAY TIME
D I STANC E
• When “DISTANCE” is selected:
METERS (when the 0 cursor button is pressed):
The unit of distance is set to meters (“m”).
FEET (when the 1 cursor button is pressed):
The unit of distance is set to feet (“ft”).
METERS
F RONT L CH
3.6 m
F RONT RCH
3.6 m
CENT ER
3.6 m
SURROUND L CH
3.0 m
SURROUND R CH
3.0 m
SUBWOOF ER
3.6 m
DE F AUL T
SE L EC T :
• When “FRONT LCH”, “FRONT RCH”, “CENTER”,
“SURROUND LCH”, ”SURROUND RCH”, “SUBWOOFER” is
selected:
Use the 0 and 1 cursor buttons to set the distance from the
listening position to the different speakers.
DE C I S I ON : ENTER BUT TON
HDMI SPE AKE R SE TUP
DELAY TIME
D I STANC E
The distance can be set within the range of 0 to 18 meters
(60 feet).
The maximum difference in speaker distance for which
adjustment is possible is 4.5 meters (15 feet).
SE L EC T :
METERS
F RONT L CH
3.6 m
F RONT RCH
3.6 m
CENT ER
3.6 m
SURROUND L CH
3.0 m
SURROUND R CH
3.0 m
SUBWOOF ER
3.6 m
DE F AUL T
40
ON
ON
DE C I S I ON : ENTER BUT TON
• When “DEFAULT” is selected:
When “DEFAULT” is selected and the ENTER button is
pressed, all the items are restored to their factory default
settings.
When digital connections are made with an AV amplifier, make
the speaker settings on the AV amplifier.
For DVD audio discs, the disc’s settings are given priority, so the
sound may not be produced as set with the above speaker mode
setting.
✽ Press the RETURN button to return to the “HDMI SPEAKER
SETUP” menu.
Remote control unit
Remote control unit
HDMI SPE AKE R SE TUP
DELAY TIME
When the HDMI connection cable is disconnected, the “SPEAKER
CONFIGURATION”, “CHANNEL LEVEL”, and “DELAY TIME”
settings under “HDMI SPEAKER SETUP” are stored.
e When “HDMI AUTO FORMAT” is selected:
PANEL RES. (Factory default)
The HDMI output format is selected automatically according to the
panel resolution of the connected HDMI device.
MAX RES.
The HDMI output format is selected automatically according to the
maximum resolution of the connected HDMI device.
METERS
D I STANC E
F RONT L CH
3.6 m
F RONT RCH
3.6 m
CENT ER
3.6 m
SURROUND L CH
3.0 m
SURROUND R CH
3.0 m
SUBWOOF ER
3.6 m
ON
DE F AUL T
SE L EC T :
DE C I S I ON : ENTER BUT TON
When connected with a DVI device, the HDMI output format is fixed
at 480P/576P.
3
r When “DENON LINK” is selected:
OFF (Factory default)
No digital audio signals are output from the DENON LINK connector.
Set to “OFF” when not using DENON LINK connections.
2nd (AUTO)
Signals are output from the DENON LINK connector in “2nd” format.
When playing the multi/stereo area of super audio CDs, the
connection to the IEEE1394 connector is detected automatically, and
if a device is connected, the signals are output from the IEEE1394
connector. If no device is connected to the IEEE1394 connector, the
signals are output from the analog audio connectors.
2nd (1394)
Signals are output from the DENON LINK connector in “2nd” format.
When playing the multi/stereo area of super audio CDs, the signals
are output from the IEEE1394 connector. No signals are output from
the analog audio connectors.
2nd (ANALOG)
Signals are output from the DENON LINK connector in “2nd” format.
When playing super audio CDs, the signals are output from the
analog audio connectors. (No signals are output from the IEEE1394
connector, even if a device is connected.) Select this if your AV
amplifier does not have an IEEE1394 connector.
When the DENON LINK 2nd connection, Super audio CD’s signals
are not output from the DENON LINK connector. Please use the
analog output terminals or the IEEE1394 connection.
When the DENON LINK is set, the down mixed audio signals are
output only from the Left and Right and Front Left and Front Right
terminals.
41
D I G I T A L I NTERF ACE SE T UP
HDM I/ DV I P I C T UR E ADJ US T
HDM I AUD IO SE TUP
PA NE L R E S .
HDM I AUTO FORMAT
MAX RES.
D E NO N L INK
I E E E1394
E X I T SE TUP
SE L EC T :
DE C I S I ON : ENTER BUT TON
D I G I T A L I NTERF ACE SE T UP
HDM I/ DV I P I C T UR E ADJ US T
HDM I AUD IO SE TUP
D
E NOI NAUTO
L INK FORMAT
HDM
D E NO N L INK
I E E E1394
OFF
2nd(AUTO)
2nd(1394)
E X I T SE TUP
SE L EC T :
2nd(ANALOG)
DE C I S I ON : ENTER BUT TON
t When “IEEE1394” is selected:
OFF (Factory default)
Digital audio signals are not output from the IEEE1394 terminal.
ON
Digital audio signals are output from the IEEE1394 terminal.
No audio signals are output from the analog connectors when
IEEE1394 is set.
Remote control unit
Remote control unit
D I G I T A L I NTERF ACE SE T UP
B When “ON” is selected:
This will lead to the “AUTO PLAY”, and “AUDIO FORMAT”
setting screens. Select the item to be set using the (•, ª) cursor
buttons and press the ENTER button.
AUTO PLAY
Set this when automatically playing this unit from another device,
under circumstances in which this unit is used in conjunction with
a DENON device that supports IEEE1394.
AUDIO FORMAT
Set this format of audio signals from IEEE1394 connector.
HDM I/ DV I P I C T UR E ADJ US T
HDM I AUD IO SE TUP
HDM I AUTO FORMAT
D E NO N L INK
I E E E1394
OFF
ON
E X I T SE TUP
SE L EC T :
DE C I S I ON : ENTER BUT TON
I E E E 1 3 9 4 SE T UP
I E E E 1 3 9 4 SE TUP
OFF
AUTO PL AY
F ORMAT 1
AUD I O F ORMAT
3
B When “AUTO PLAY” is selected:
OFF (Factory default)
Set this when you do not wish to control the operation of this unit
from another device.
ON
Set this when you wish to control the operation of this unit from
another device.
SE L EC T :
DE C I S I ON : ENTER BUT TON
I E E E 1 3 9 4 SE T UP
I E E E 1 3 9 4 SE TUP
B When “AUDIO FORMAT” is selected:
FORMAT1 (Factory default)
Set this when you conjunction with a DENON device.
FORMAT2
This is a mode for future system expansion.
AUTO PL AY
OFF
AUD I O F ORMAT
ON
SE L EC T :
[IEEE1394 indicator in the display]
• When “IEEE1394” set to “ON”,
this indicator lights as bellow.
flashing .......................self check of IEEE1394 connections.
light.............................IEEE1394 connection is OK.
slow flashing ..............IEEE1394 connection is NG. (Loop
connection) confirm the connection.
fast flashing ................IEEE1394 connection is NG. confirm the
connection.
DE C I S I ON : ENTER BUT TON
I E E E 1 3 9 4 SE T UP
I E E E 1 3 9 4 SE TUP
AUTO PL AY
AUD I O F ORMAT
FORMAT1
FORMAT2
SE L EC T :
DE C I S I ON : ENTER BUT TON
✽ To exit the setup mode
Use the ª cursor button to select “EXIT SETUP”, then press the ENTER button. It is also possible to quit by pressing the SETUP
button on the remote control unit.
42
When “VIDEO SETUP” is selected
1
See pages 31, 32.
Use the • and ª cursor buttons to select the desired setting, then press
the ENTER button.
TV ASPECT
Use this to set the shape of your TV’s screen.
TV TYPE
Use this to set your TV’s video format (NTSC, PAL or MULTI).
2
TV SYSTEM
Select the video output connected to the TV or monitor whose image
you want to view.
On the DVD-A1XV, interlace output, progressive output and HDMI/DVI
output signals are each processed on independent video circuits. The
audio output is optimized for the selected video output, so choose the
video output you wish to view.
COMPONENT VIDEO OUT
Use this to select either the progressive image output or interlace
image output.
Remote control unit
Remote control unit
V I DEO SE TUP
T V ASPECT
W I DE ( 1 6 : 9 )
MUL T I
TV TYPE
TV SYS T EM
PROGRE SS I VE
COMPONENT V I DEO OUT
PROGRE SS I VE
SQUEE Z E MODE
OFF
PROGRESS I V E MODE
AUTO
AV1 V I DEO MODE
V I DEO
SQUEEZE MODE
E X I T SE TUP
The size of the screen to be output can be switched.
SE L EC T :
DE C I S I ON : ENTER BUT TON
PROGRESSIVE MODE
The play DVD video, select the desired video mode.
AV1 VIDEO MODE
To select whether composite video signals or S video signals or RGB
signals will be output from the AV1 SCART terminals.
Use the • and ª cursor buttons to select the desired setting, then press
the ENTER button.
3
q When “TV ASPECT” is selected:
4:3 PS
Select this to play wide DVDs in the pan & scan mode (with the sides
of the picture cut off). Discs for which pan & scan is not specified are
played in the letter box mode.
4:3 LB
Select this to play wide DVDs in the letter box mode (with black
strips at the top and bottom).
WIDE (16:9) (Factory default)
Select this to play wide DVDs in the full-screen mode.
Remote control unit
Remote control unit
V I DEO SE TUP
T V ASPECT
4 : 3 PS
TV TYPE
4 : 3 LB
TV SYS T EM
W I DE ( 1 6 : 9 )
COMPONENT V I DEO OUT
SQUEE Z E MODE
PROGRESS I V E MODE
AV1 V I DEO MODE
E X I T SE TUP
SE L EC T :
43
DE C I S I ON : ENTER BUT TON
w When “TV TYPE” is selected:
NTSC
Select this when your TV’s video format is NTSC.
If NTSC is selected, output format is fixed to NTSC.
PAL
Select this when your TV’s video format is PAL.
If PAL is selected, output format is fixed to PAL.
MULTI (Factory default)
Select this when your TV is compatible with both the NTSC and PAL
formats.
NTSC signals are output from the video output jacks when discs
recorded in NTSC format are played, and PAL signals are output from
the video output jacks when discs recorded in PAL format are played.
NOTE:
• If “TV TYPE” is set to a format other than a registered TV format, the
image may no longer be smooth and the top and bottom of the image
may be cut off.
3
e When “TV SYSTEM” is selected:
PROGRESSIVE (Factory default)
The audio signals are synchronized with the progressive output.
(For component video output signals when “COMPONENT VIDEO
OUT” at “VIDEO SETUP” is set to “PROGRESSIVE”)
INTERLACED
The audio signals are synchronized with the interlaced output.
(For video output and S-video output signals, as well as for
component video output signals when “COMPONENT VIDEO OUT”
at “VIDEO SETUP” is set to “INTERLACED”)
HDMI/DVI
The audio signals are synchronized with the video signals output via
the HDMI/DVI connectors.
OTHERS
Select this when you want to view both the interlace
output/progressive output image and the HDMI/DVI output image at
the same time.
The audio signals are set to the optimum timing for the interlace
output/progressive output image and the HDMI/DVI output image.
(Note, however, that the audio signals are not synchronized with the
interlace output/progressive output image and the HDMI/DVI output
image. To synchronize them, set to another position.)
r When “COMPONENT VIDEO OUT” is selected: (NOTE)
PROGRESSIVE (Factory default)
The signals output from the DVD-A1XV’s “COMPONENT VIDEO
OUT” connector are formatted in the progressive format.
Select this when using the DVD-A1XV connected to a progressive
type TV.
INTERLACED
The signals output from the DVD-A1XV’s “COMPONENT VIDEO
OUT” connector are formatted in the interlaced format.
Select this when using the DVD-A1XV connected to an interlace type
TV.
NOTE:
• For the component output only, it is possible to switch between
interlace image output and progressive image output. It is not
possible to specify progressive image output for the Video output
connector or S-Video output connector.
44
Remote control unit
Remote control unit
V I DEO SE TUP
T V ASPECT
TV TYPE
NTSC
PAL
TV SYS T EM
COMPONENT V I DEO OUT
MUL T I
SQUEE Z E MODE
PROGRESS I V E MODE
AV1 V I DEO MODE
E X I T SE TUP
SE L EC T :
DE C I S I ON : ENTER BUT TON
V I DEO SE TUP
T V ASPECT
TV TYPE
PROGRE SS I VE
TV SYS T EM
COMPONENT V I DEO OUT
I NT E RL AC ED
HDMI / DV I
SQUEE Z E MODE
OTHERS
PROGRESS I V E MODE
AV1 V I DEO MODE
E X I T SE TUP
SE L EC T :
DE C I S I ON : ENTER BUT TON
V I DEO SE TUP
T V ASPECT
TV TYPE
TV SYS T EM
COMPONENT V I DEO OUT
SQUEE Z E MODE
PROGRE SS I VE
I NT E RL AC ED
PROGRESS I V E MODE
AV1 V I DEO MODE
E X I T SE TUP
SE L EC T :
DE C I S I ON : ENTER BUT TON
t When “SQUEEZE MODE” is selected:
OFF (Factory default)
Select this to display as full size of a 16:9 TV,
regardless of the image’s size.
TV
ON
Select this to display the image with a ratio of 4:3 at
the center of a 16:9 TV display, regardless of the
TV
image’s size.
AUTO
Select this when playing back a 4:3 image, display at 4:3 aspect ratio
at the center of a 16:9 TV.
Only effective for set to “WIDE (16:9)” at “TV ASPECT”.
(See page 43.)
No effective for interlaced image.
Remote control unit
Remote control unit
V I DEO SE TUP
T V ASPECT
TV TYPE
TV SYS T EM
COMPONENT V I DEO OUT
OF F
SQUEE Z E MODE
ON
PROGRESS I V E MODE
AUTO
AV1 V I DEO MODE
E X I T SE TUP
SE L EC T :
3
y When “PROGRESSIVE MODE” is selected:
AUTO (Factory default)
The set identifies the type of material on the disc being played (film
or video) and selects the mode automatically.
VIDEO1
This mode is best suited for playing discs containing video material.
VIDEO2
This mode is best suited for playing discs containing video material
or 30-frame film material.
DE C I S I ON : ENTER BUT TON
V I DEO SE TUP
T V ASPECT
TV TYPE
TV SYS T EM
COMPONENT V I DEO OUT
SQUEE Z E MODE
AUTO
PROGRESS I V E MODE
V ID E O1
AV1 V I DEO MODE
V ID E O2
E X I T SE TUP
SE L EC T :
u When “AV1 VIDEO MODE” is selected:
VIDEO (Factory default)
Composite video signals will be output from the AV1 SCART
terminal.
S-VIDEO
S video signals will be output from the AV1 SCART terminal.
RGB
RGB signals will be output from the AV1 SCART terminal.
DE C I S I ON : ENTER BUT TON
V I DEO SE TUP
T V ASPECT
TV TYPE
TV SYS T EM
COMPONENT V I DEO OUT
SQUEE Z E MODE
PROGRESS I V E MODE
AV1 V I DEO MODE
V I DE O
S - V I DE O
E X I T SE TUP
SE L EC T :
RGB
DE C I S I ON : ENTER BUT TON
✽ To exit the setup mode
Use the ª cursor button to select “EXIT SETUP”, then press the ENTER button. It is also possible to quit by pressing the SETUP
button on the remote control unit.
45
When “AUDIO SETUP” is selected
1
See pages 31, 32.
Use the • and ª cursor buttons to select the desired setting, then press
the ENTER button.
AUDIO CHANNEL
Use this to adjust for the connected speaker systems.
DIGITAL OUTPUT
Use this to select the digital output’s signal format.
LPCM (44.1 kHz/48 kHz)
Use this to set the digital audio output when playing DVDs recorded in
linear PCM audio.
2
SOURCE DIRECT
This permits a setting to output the audio without adding speaker
settings to the audio signals of DVD audio or Super Audio CD.
BASS ENHANCER
Set whether or not to output audio signals from the subwoofer when
playing two-channel audio signals.
The BASS ENHANCER settings do not apply to digital outputs.
COMPRESSION
Use this to set the dynamic range output when playing discs.
Remote control unit
AUD I O SE TUP
AUD I O CHANNE L
MUL T I CHANNE L
D I G I TAL OUTPUT
NORMAL
L PCM (4 4 . 1 kHz / 4 8 kH z)
OF F
SOURCE D I RE CT
OF F
BASS ENHANCE R
OF F
COMPRESS ION
OF F
SACD F I L TER
50kHz
E X I T SE TUP
SE L EC T :
SACD FILTER
The low pass filter value when playing Super Audio CDs can be set.
The audio channel, digital output, LPCM conversion mode and source
direct bass expand items cannot be selected when DENON LINK or
IEEE1394 is selected or when the HDMI audio is “MULTI (NORMAL)”.
46
Remote control unit
DE C I S I ON : ENTER BUT TON
Use the • and ª cursor buttons to select the desired setting, then press
the ENTER button.
q When “AUDIO CHANNEL” is selected:
MULTI CHANNEL (Factory default)
Select this for systems in which three or more speakers are
connected.
When MULTI CHANNEL is set, the speaker settings (SPEAKER
CONFIGURATION), speaker output level adjustment (CHANNEL
LEVEL) and speaker distances (DELAY TIME) can be set.
2CH (SRS OFF)
Select this does not to use the SRS TruSurround function for
systems in which only two speakers are connected.
When connecting with Dolby Prologic decoder (Dolby Prologic
amplifier etc.), select this setting.
2CH (SRS ON)
Select this to use the SRS TruSurround function for systems in which
only two speakers are connected.
The indicator “
Remote control unit
AUD I O SE TUP
AUD I O CHANNE L
MUL T I CHANNE L
DIGITAL OUTPUT
2CH(SRS OFF)
L PCM (4 4 . 1 kH z / 4 8 kH z)
2CH(SRS ON)
SOURCE D I RE CT
BASS ENHANCE R
COMPRESS ION
SACD F I L TER
” in the display lights at this mode.
E X I T SE TUP
2 The SRS TruSurround function
3
Remote control unit
SE L EC T :
DE C I S I ON : ENTER BUT TON
(only for DVD-videos and Video CDs)
The multi-channel sound normally achieved with five speakers is
recreated using only the two front stereo speakers. This results in
a sound with a nearly natural sense of movement that seems to
surround the head, without the strong directivity characteristic of
multi-speaker systems.
NOTES:
• Note that for some discs the effect will be weak or there will be
no effect.
• Turn off other surround functions (the TV’s surround mode,
etc.).
is a trademark of SRS Labs, Inc.
TruSurround technology is incorporated under license from SRS
Labs, Inc.
B When “MULTI CHANNEL” is selected, use the • and ª cursor
buttons to select the item to be set, then press the ENTER button.
SPEAKER CONFIGURATION
Use this to select the types of the different speakers.
CHANNEL LEVEL
Use this to adjust the output level of the different speakers.
DELAY TIME
Use this to set the distance from the different speakers to the
listening position.
SPE AKE R SE TUP
SPE AKER CONF I GURAT I ON
CHANNE L L E VE L
DE L AY T I ME
AUD I O SE TUP
The SPEAKER CONFIGURATION settings only apply to analog
outputs.
✽ To exit the SPEAKER SETUP mode
Use the ª cursor button to select “AUDIO SETUP” then press
ENTER button.
47
SE L EC T :
DE C I S I ON : ENTER BUT TON
B When “SPEAKER CONFIGURATION” is selected, use the • and
ª cursor buttons to select the speaker to be set then press the
ENTER button.
• The type of speaker used for the front speakers, center speaker,
subwoofer and surround speakers can be set. Use the • and ª
cursor buttons to select the speaker type, then press the
ENTER button.
LARGE
Select this when a large speaker is connected.
SMALL
Select this when a small speaker is connected.
NONE
Select this when no speaker is connected.
YES
Select this when a subwoofer is connected.
NO
Select this when no subwoofer is connected.
• When “CROSSOVER” is selected:
40 Hz, 60 Hz, 80 Hz (Factory default), 100 Hz, 120 Hz, set the
frequency of crossover.
3
Remote control unit
Remote control unit
SPE AKE R SE TUP
SPE AKER CONF I GURAT I ON
F RONT SP
L ARGE
CENT ER SP
L ARGE
SUBWOOF ER
SURROUND SP
CROSSOVE R
SE L EC T :
YES
L ARGE
80Hz
DE C I S I ON : ENTER BUT TON
✽ Press the RETURN button to return to the “SPEAKER SETUP”
menu.
B When “CHANNEL LEVEL” is selected, use the • and ª cursor
buttons to select the speaker to be adjusted, then use the 0 and
1 cursor buttons to set the level.
• TEST TONE
Use the 0 and 1 cursor buttons to select auto or manual.
Adjust so that the volume of the test tones output from the
different speakers sounds the same.
• The volume level output from the front speakers (left and right
channels), center speaker, surround speakers (left and right
channels) and subwoofer can be adjusted.
• The volume level can be adjusted between 0 and –10 dB in
steps of 1 dB.
• Settings SW +10 dB to “ON” increases by 10 dB the volume
level that is output from the subwoofer.
Remote control unit
SPE AKE R SE TUP
CHANNEL LEVEL
✽ Press the RETURN button to return to the “SPEAKER SETUP”
menu.
SE L EC T :
48
T E ST TONE
OF F
F RONT L CH
0 dB
CENT ER
0 dB
F RONT RCH
0 dB
SURROUND R CH
0 dB
SURROUND L CH
0 dB
SUBWOOF ER
0 dB
SW + 1 0 d B
OFF
DE C I S I ON : ENTER BUT TON
B When “DELAY TIME” is selected:
With 5.1-channel surround sound, ideally the distance between
the listening position and all the speakers aside from the
subwoofer should be the same. The delay time setting can be
used to make the sound from the different speakers reach the
listening position at the same time.
Remote control unit
Use the • and ª cursor buttons to select the setting item, then
press the ENTER button.
Remote control unit
SPE AKE R SE TUP
DELAY TIME
D I STANC E
• When “DISTANCE” is selected:
METERS (when the 0 cursor button is pressed):
The unit of distance is set to meters (“m”).
FEET (when the 1 cursor button is pressed):
The unit of distance is set to feet (“ft”).
3.6m
F RONT RCH
3.6m
CENT ER
3.6m
SURROUND L CH
3.0m
SURROUND R CH
3.0m
SUBWOOF ER
3.6m
DE F AUL T
SE L EC T :
METERS
F RONT L CH
ON
DE C I S I ON : ENTER BUT TON
SPE AKE R SE TUP
DELAY TIME
D I STANC E
3
• When “FRONT LCH”, “FRONT RCH”, “CENTER”,
“SURROUND LCH”, “SURROUND RCH”, “SUBWOOFER” is
selected:
Use the 0 and 1 cursor buttons to set the distance from the
listening position to the different speakers.
The distance can be set within the range of 0 to 18 meters
(60 feet).
The maximum difference in speaker distance for which
adjustment is possible is 4.5 meters (15 feet).
3.6 m
F RONT RCH
3.6 m
CENT ER
3.6 m
SURROUND L CH
3.0 m
SURROUND R CH
3.0 m
SUBWOOF ER
3.6 m
DE F AUL T
SE L EC T :
METERS
F RONT L CH
ON
DE C I S I ON : ENTER BUT TON
SPE AKE R SE TUP
DELAY TIME
D I STANC E
• When “DEFAULT” is selected:
When “DEFAULT” is selected and the ENTER button is
pressed, all the items are restored to their factory default
settings.
3.6 m
F RONT RCH
3.6 m
CENT ER
3.6 m
SURROUND L CH
3.0 m
SURROUND R CH
3.0 m
SUBWOOF ER
3.6 m
DE F AUL T
SE L EC T :
METERS
F RONT L CH
ON
DE C I S I ON : ENTER BUT TON
SPE AKE R SE TUP
DELAY TIME
When digital connections are made with an AV amplifier, make
the speaker settings on the AV amplifier.
For DVD audio discs, the disc’s settings are given priority, so the
sound may not be produced as set with the above speaker mode
setting.
D I STANC E
✽ Press the RETURN button to return to the “SPEAKER SETUP”
menu.
49
3.6 m
F RONT RCH
3.6 m
CENT ER
3.6 m
SURROUND L CH
3.0 m
SURROUND R CH
3.0 m
SUBWOOF ER
3.6 m
DE F AUL T
SE L EC T :
METERS
F RONT L CH
ON
DE C I S I ON : ENTER BUT TON
w When “DIGITAL OUTPUT” is selected:
NORMAL (Factory default)
When playing DVDs recorded in Dolby Digital or DTS, bitstream
signals are output from the digital audio output terminals. When
playing DVDs recorded in linear PCM or packed PCM, linear PCM
signals are output.
Select “NORMAL” when making digital connections to an AV
amplifier with built-in Dolby Digital and DTS decoder.
PCM
When playing Dolby Digital/DTS bitstream signals or DVDs recorded
in linear PCM or packed PCM, the signals are converted into 48
kHz/16-bit PCM (2-channel) signals and output from the digital
outputs. When playing DVDs recorded in PCM, linear PCM signals
are output.
3
e When “LPCM (44.1 kHz/ 48 kHz)” is selected:
OFF (Factory default)
When playing linear PCM or packed PCM DVDs that are not
copyright-protected, for 2-channel PCM audio signals up to 96 kHz,
linear PCM signals are output as such without being converted from
the digital outputs. (176.4 kHz and 192 kHz signals are converted to
88.2 kHz and 96 kHz, respectively.)
For DVDs containing multi-channel PCM signals, the digital signals
are down-mixed for output into two channels, front left and right.
(Only the front left and right channels are output for sources for
which down-mixing is prohibited.)
When playing copyright-protected linear PCM or packed PCM DVDs,
in consideration of copyrights, no digital signals are output for
sources exceeding 48 kHz/16 bits. When playing such sources,
either set to “ON” or make analog connections. (See page 16.)
ON
Linear PCM and packed PCM signals are converted to 44.1 kHz or
48 kHz and output. (The PCM digital audio output signals are
converted to 48 kHz or less in consideration of copyrights.) When
making digital connections to an AV amplifier that is not compatible
with 96 kHz/88.2 kHz signals, set to “ON”.
r When “SOURCE DIRECT” is selected:
OFF (Factory default)
Please set to OFF when performing speaker settings or setting the
delay time and playing back.
ON
Set to ON when playing back without performing the processing of
speaker settings. Performing this setting will result in the setting of
the DTS recommended all-channel, full bandwidth playback. (Note
that the volume of the sub woofer will increase by 5 dB, and there
will be an increase of 15 dB with a Super Audio CD.) This is also set
when playing back a 6-channel source of DVD audio that has been
recorded with all channels and full bandwidth. When set to “ON”,
the speaker size will be set to “Large” for all speakers and the sub
woofer will be set to “Yes”. When playing back software such as
this, perform the analog connections according to the software
instruction manual.
50
Remote control unit
Remote control unit
AUD I O SE TUP
AUD I O CHANNE L
NORMAL
DIGITAL OUTPUT
L PCM (4 4 . 1 kHz / 4 8 kH z)
PCM
SOURCE D I RE CT
BASS ENHANCE R
COMPRESS ION
SACD F I L TER
E X I T SE TUP
SE L EC T :
DE C I S I ON : ENTER BUT TON
AUD I O SE TUP
AUD I O CHANNE L
D I G I TAL OUTPUT
L PCM (4 4 . 1 kHz / 4 8 kH z)
OF F
SOURCE D I RE CT
ON
BASS ENHANCE R
COMPRESS ION
SACD F I L TER
E X I T SE TUP
SE L EC T :
DE C I S I ON : ENTER BUT TON
AUD I O SE TUP
AUD I O CHANNE L
D I G I TAL OUTPUT
L PCM (4 4 . 1 kHz / 4 8 kH z)
SOURCE D I RE CT
OF F
BASS ENHANCE R
ON
COMPRESS ION
SACD F I L TER
E X I T SE TUP
SE L EC T :
DE C I S I ON : ENTER BUT TON
t When “BASS ENHANCER” is selected: (For 2 channel source.)
OFF (Factory default)
No sound is produced from the subwoofer.
ON
Sound is produced from the subwoofer.
In the case, set the subwoofer to “YES” at the speaker settings.
Remote control unit
Remote control unit
AUD I O SE TUP
AUD I O CHANNE L
This works only with analog audio output.
This does not work, at “SOURCE DIRECT” is on.
D I G I TAL OUTPUT
L PCM (4 4 . 1 kHz / 4 8 kH z)
SOURCE D I RE CT
BASS ENHANCE R
OF F
COMPRESS ION
ON
SACD F I L TER
E X I T SE TUP
SE L EC T :
3
y When “COMPRESSION” is selected:
OFF (Factory default)
Select this for the standard range.
ON
Select this to achieve powerful sound even when the volume is low.
This setting is suited for watching DVDs late at night with the volume
low. (This setting is only valid for DVDs recorded in Dolby Digital.)
DE C I S I ON : ENTER BUT TON
AUD I O SE TUP
AUD I O CHANNE L
D I G I TAL OUTPUT
L PCM (4 4 . 1 kHz / 4 8 kH z)
SOURCE D I RE CT
BASS ENHANCE R
COMPRESS ION
OF F
SACD F I L TER
ON
E X I T SE TUP
SE L EC T :
u When “SACD (Super Audio CD) FILTER” is selected:
50kHz (Factory default)
When playing Super Audio CDs, high frequencies of 50kHz and
higher are cut.
100kHz
When playing Super Audio CDs, high frequencies of 100kHz and
higher are cut.
Set to 100kHz when a high frequency compatible AV amplifier is
connected.
DE C I S I ON : ENTER BUT TON
AUD I O SE TUP
AUD I O CHANNE L
D I G I TAL OUTPUT
L PCM (4 4 . 1 kHz / 4 8 kH z)
SOURCE D I RE CT
BASS ENHANCE R
COMPRESS ION
SACD F I L TER
50kHz
100kHz
E X I T SE TUP
SE L EC T :
DE C I S I ON : ENTER BUT TON
✽ To exit the setup mode
Use the ª cursor button to select “EXIT SETUP”, then press the ENTER button. It is also possible to quit by pressing the SETUP
button on the remote control unit.
51
When “RATINGS” is selected
1
See pages 31, 32.
Use the • and ª cursor buttons to select the desired
setting, then press the ENTER button.
RAT I NGS
8(NO L IMI T)
RAT I NG L EVE L
PASSWORD
2
RATING LEVEL
Use this to restrict playback of adult DVDs you do
not want children to view. Note that even with adult
DVDs, viewing cannot be restricted unless the
restriction level is recorded on the disc.
E X I T SE TUP
Remote control unit
PASSWORD
Use this to change the password.
The default password is “0000”.
SE L EC T :
DE C I S I ON : ENTER BUT TON
Remote control unit
Use the • and ª cursor buttons to select the desired
setting, then press the ENTER button.
3
q When “RATING LEVEL” is selected:
0 (LOCK ALL)
Select this to disable playback of all DVDs.
Use this for example to disable playback of adult
DVDs on which the rating level is not recorded.
1
Select this to play only DVDs for children. (Adult
and general audience DVDs cannot be played.)
2 to 7
Select this to play DVDs for general audiences
and children. Adult DVDs cannot be played.
8 (NO LIMIT) (Factory default)
Select this to play all DVDs.
RAT I NGS
0(LOCK ALL)
RAT I NG L EVE L
1
PASSWORD
2
3
E X I T SE TUP
4
Remote control unit
5
6
7
8(NO L IMI T)
SE L EC T :
DE C I S I ON : ENTER BUT TON
Remote control unit
RAT I NGS
RAT I NG L EVE L
PASSWORD
Use the number buttons to input a 4-digit
password, then press the ENTER button.
The default password is “0000”.
Do not forget the password.
The setting cannot be changed without
inputting the correct password.
CURRENT PASSWORD
Remote control unit
SE L EC T : 0 - 9
Remote control unit
52
----
PL E ASE ENT E R PASSWORD
DE C I S I ON : ENTER BUT TON
Remote control unit
Remote control unit
w When “PASSWORD” is selected:
Use the 1 cursor button to select the
“CHANGE”, then press the ENTER button.
RAT I NGS
RAT I NG L EVE L
CHANGE
PASSWORD
Remote control unit
E X I T SE TUP
SE L EC T :
DE C I S I ON : ENTER BUT TON
Remote control unit
Use the number buttons to input a old (current) 4digit password.
RAT I NGS
The default password is “0000”.
RAT I NG L EVE L
PASSWORD
XXXX
OL D PASSWORD
3
NEW PASSWORD
----
CONF I RM PASSWORD
----
PL E ASE ENT E R O L D PASSWORD
Remote control unit
SE L EC T : 0 - 9
Use the number buttons to input a new 4-digit
password.
DE C I S I ON : ENTER BUT TON
RAT I NGS
RAT I NG L EVE L
PASSWORD
XXXX
OL D PASSWORD
NEW PASSWORD
XXXX
CONF I RM PASSWORD
----
PL E ASE ENT E R NEW PASSWORD
SE L EC T : 0 - 9
Use the number buttons to input a new 4-digit
password again. (for the confirmation.)
Then press the ENTER button.
DE C I S I ON : ENTER BUT TON
RAT I NGS
RAT I NG L EVE L
PASSWORD
Do not forget the password.
The setting cannot be changed without
inputting the correct password.
XXXX
OL D PASSWORD
Remote control unit
NEW PASSWORD
XXXX
CONF I RM PASSWORD
XXXX
PL E ASE REENT E R NEW PASSWORD
SE L EC T : 0 - 9
DE C I S I ON : ENTER BUT TON
✽ To exit the setup mode
Use the ª cursor button to select “EXIT SETUP”, then press the ENTER button. It is also possible to quit by pressing the SETUP
button on the remote control unit.
53
When “OTHER SETUP” is selected
1
See pages 31, 32.
Use the • and ª cursor buttons to select the desired setting, then press
the ENTER button.
PLAYER MODE
The DVD video play mode can be set to play the DVD video contents
included on a DVD audio disc.
CAPTIONS
Use this to set whether or not to display the closed captions recorded
on DVDs.
WALL PAPER
Use this to select the image to be shown on the screen in the stop
mode and CD play mode.
2
Remote control unit
Remote control unit
OTHE R SE TUP
SCREEN SAVER
The screen saver function prevents ghosting on the TV screen.
DISPLAY
The setting of whether or not there will be an indication on the display
of this unit only for the 2 seconds immediately following the operation,
even while the display has been off.
AUTO POWER MODE
To save power, DVD-A1XV’s can automatically be set to the standby
mode when it is not used for long periods of time.
PL AYE R MODE
AUD I O
CAPT I ONS
OF F
WAL L PAPER
BLUE
SCRE EN SAVER
OF F
D I SPL AY
OF F
AUTO POWER MODE
SL I DE SHOW
OF F
5 SEC
E X I T SE TUP
SE L EC T :
DE C I S I ON : ENTER BUT TON
SLIDE SHOW
The time interval for switching to the next still picture when playing
slide shows of still pictures (in JPEG format) can be set.
Use the • and ª cursor buttons to select the desired setting, then press
the ENTER button.
3
q When “PLAYER MODE” is selected:
AUDIO (Factory default)
Set this to play the DVD audio signals as such.
VIDEO
Set this to play the DVD video contents included on a DVD audio
disc.
Remote control unit
Remote control unit
OTHE R SE TUP
PL AYE R MODE
AUD I O
CAPT I ONS
V I DEO
WAL L PAPER
SCRE EN SAVER
D I SPL AY
AUTO POWER MODE
SL I DE SHOW
E X I T SE TUP
SE L EC T :
54
DE C I S I ON : ENTER BUT TON
w When “CAPTIONS” is selected:
OFF (Factory default)
Select this when you do not want to display the captions on the
screen when playing DVDs containing English captions
ON
Select this to display the captions on the screen when playing DVDs
containing English captions.
Remote control unit
Remote control unit
OTHE R SE TUP
NOTES:
• An English caption decoder is required to display English
captions.
• DVDs with caption signals are indicated by the
mark.
,
,
PL AYE R MODE
CAPT I ONS
WAL L PAPER
ON
SCRE EN SAVER
D I SPL AY
AUTO POWER MODE
English captions cannot be displayed when playing DVDs which
do not contain caption signals.
SL I DE SHOW
E X I T SE TUP
SE L EC T :
3
OF F
e When “WALL PAPER” is selected:
BLUE (Factory default)
Select this to display a blue background on the TV display.
GRAY
Select this to display a gray background on the TV display.
BLACK
Select this to display a black background on the TV display.
PICTURE
Select this to display the picture on the TV display.
DE C I S I ON : ENTER BUT TON
OTHE R SE TUP
PL AYE R MODE
CAPT I ONS
WAL L PAPER
SCRE EN SAVER
D I SPL AY
AUTO POWER MODE
BLUE
GRAY
BLACK
PICTURE
SL I DE SHOW
E X I T SE TUP
SE L EC T :
r When “SCREEN SAVER” is selected:
OFF (Factory default)
The screen saver function does not work.
ON
If more than 5 minutes passes while in the stop, pause or other
mode, the screen saver function is activated to prevent ghosting on
the TV screen.
DE C I S I ON : ENTER BUT TON
OTHE R SE TUP
PL AYE R MODE
CAPT I ONS
WAL L PAPER
SCRE EN SAVER
OFF
D I SPL AY
ON
AUTO POWER MODE
SL I DE SHOW
E X I T SE TUP
SE L EC T :
t When “DISPLAY” is selected:
OFF (Factory default)
This is valid when the display has been switched off. The display will
not show an indication even when the button (ex. skip, stop, etc.)
has been pressed.
ON
This is valid when the display has been switched off. When the
button (ex. skip, stop, etc.) is pressed, the indication will appear on
the display for approximately 2 seconds.
OTHE R SE TUP
PL AYE R MODE
CAPT I ONS
WAL L PAPER
SCRE
D
I SPLEN
AYSAVER
D I SPL AY
AUTO POWER MODE
OF F
ON
SL I DE SHOW
E X I T SE TUP
SE L EC T :
55
DE C I S I ON : ENTER BUT TON
DE C I S I ON : ENTER BUT TON
y When “AUTO POWER MODE” is selected:
OFF (Factory default)
The power does not automatically switch to the standby mode.
ON
The DVD-A1XV’s power turns off and the standby mode is set if the
DVD-A1XV remains in the stop mode for approximately 30 minutes.
Remote control unit
Remote control unit
OTHE R SE TUP
PL AYE R MODE
CAPT I ONS
WAL L PAPER
SCRE EN SAVER
D I SPL AY
3
AUTO POWER MODE
SL I DE SHOW
OF F
ON
E X I T SE TUP
SE L EC T :
u When “SLIDE SHOW” is selected:
Use the • and ª cursor buttons to set the time interval.
The time interval can be set within 5 and 15 seconds. (The factory
default setting is 5 seconds.)
DE C I S I ON : ENTER BUT TON
OTHE R SE TUP
PL AYE R MODE
CAPT I ONS
WAL L PAPER
SCRE EN SAVER
D I SPL AY
AUTO POWER MODE
SL I DE SHOW
5SEC
E X I T SE TUP
SE L EC T :
DE C I S I ON : ENTER BUT TON
✽ To exit the setup mode
Use the ª cursor button to select “EXIT SETUP”, then press the ENTER button. It is also possible to quit by pressing the SETUP
button on the remote control unit.
56
9 USING THE PURE DIRECT MODE
2 In the pure direct mode, only analog audio signals (no video signals, etc.) are output, thereby achieving high quality sound.
BACK LIGHT
ANGLE
OPEN/CLOSE
PLAY
STOP
STILL / PAUSE
ON / STANDBY
SUBTITLE
AUDIO
TOP MENU
DISPLAY
MENU
RETURN
2
VIDEO MODE
HDMI / DVI
SELECT
FORMAT
SUPER
AUDIO CD
SET UP
STOP
PURE
DIRECT
SELECT
PUSH ENTER
SKIP
DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER
Display the setting mode
STILL/PAUSE
PLAY
SLOW/SEARCH
DVD-A1XV
PAGE
REPEAT
A-B
RANDOM
MARKER
ZOOM
SETUP
PICTURE
ADJUST
PICT ADJ.
MEMORY
DIMMER
PURE DIRECT
4
SELECT
4
1, 3
PURE DIRECT MEMORY
SE TUP
PURE DIRECT
MEMORY
1
PURE D I R E CT MODE
MODE1
MODE2
SELECT
PURE D I R E CT MODE 1
Press the PURE DIRECT MEMORY button.
• The output status of the video signals, etc., can be
stored at MODE 1 and MODE 2 as desired.
DI G I T AL OUTPUT
V I DEO OUT
ON
ON
DI SPL AY
ON
Remote control unit
SE L EC T :
2
Use the • and ª cursor buttons to select the mode, then
press the ENTER button.
DIGITAL OUTPUT
ON : Digital audio signals are output.
OFF : Digital audio signals are not output.
✽ Does not function for DENON LINK or IEEE1394
digital outputs. For these outputs, set “OFF” at the
initial settings.
VIDEO OUT
ON : Video signals are output.
OFF : Video signals are not output.
DISPLAY
ON : It is indicate in Display of the main unit.
OFF : It is not indicate in Display of the main unit.
✽ When the video output is set to “OFF” or “ALL OFF”,
neither HDMI video nor audio signals are output.
Also, when the “HDMI AUDIO SETUP” is set to
“MULTI (NORMAL)”, the setting of DIGITAL OUTPUT
cannot be made. (See pages 38, 39.)
✽ When DENON LINK and IEEE 1394 settings are valid,
the setting of DIGITAL OUTPUT cannot be selected.
DE C I S I ON : ENTE R BUT TON
PURE DIRECT MEMORY
SE TUP
PURE D I R E CT MODE
PURE D I R E CT MODE 1
DI G I T AL OUTPUT
ON
V I DEO OUT
OFF
DI SPL AY
SE L EC T :
DE C I S I ON : ENTE R BUT TON
Remote control unit
PURE DIRECT
MEMORY
3
SELECT
Press the PURE DIRECT MEMORY button.
• All of the settings are stored in the memory.
Remote control unit
57
MODE1
4
Press the PURE DIRECT SELECT button.
• The modes described below will appear on the display.
NORMAL : All signals are output normally.
MODE 1 : The settings stored for MODE 1 are used.
The factory default settings are:
“DIGITAL OUTPUT” : “ON”
“VIDEO OUT”
: “ON”
“DISPLAY”
: “ON”
MODE 2 : The settings stored for MODE 2 are used.
The factory default settings are:
“DIGITAL OUTPUT” : “ON”
“VIDEO OUT”
: “ON”
“DISPLAY”
: “ON”
ALL OFF : No indicate in Display of the main unit,
video and digital signals are not
out.(except analog audio output)
PURE
DIRECT
SELECT
PURE DIRECT
MEMORY
Main unit
SELECT
Remote control unit
10 USING THE SUPER AUDIO CD SETUP
2 On a Super Audio CD, the stereo and multi – channel areas are separate.
Hybrid discs comprise 2-layer structure of Super Audio CD layer and a CD layer.
The area/layer can be set to be played with priority.
POWER OFF
OPEN/CLOSE
PLAY
POWER ON
STOP
HDMI/DVI
SELECT
OPEN/
CLOSE
FORMAT
NTSC/PAL
SUPER AUDIO
CD SETUP
STILL / PAUSE
PROGRAM
/DIRECT
ON / STANDBY
VIDEO MODE
HDMI / DVI
SELECT
FORMAT
SUPER
AUDIO CD
SET UP
PURE
DIRECT
SELECT
CLEAR
SEARCH MODE
CALL
PUSH ENTER
DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER
DVD-A1XV
BACK LIGHT
ANGLE
1
Display the setting mode
1
Press the SUPER AUDIO CD SETUP button.
• The modes described below will appear on the display.
MULTI (Factory default)
When playing a Super Audio CD disc, the multi –
channel area will be played back with priority.
STEREO
When playing a Super Audio CD disc, the stereo area
will be played back with priority.
CD
When playing a Super Audio CD disc, the CD layer will
be played back with priority.
✽ When playing back a disc that does not have a selected
area/layer, another area/layer will be played back
automatically.
58
SUBTITLE
AUDIO
TOP MENU
DISPLAY
MENU
RETURN
SUPER
AUDIO CD
SETUP
MULTI
Main unit
SUPER AUDIO
CD SETUP
STEREO
CD
Remote control unit
1
11 ADJUSTING THE PICTURE QUALITY
BACK LIGHT
ANGLE
SUBTITLE
AUDIO
TOP MENU
DISPLAY
MENU
RETURN
2, 3, 4, 5, 6, 7
STOP
STILL/PAUSE
SKIP
PLAY
SLOW/SEARCH
PAGE
REPEAT
A-B
RANDOM
MARKER
ZOOM
SETUP
PICTURE
ADJUST
PICT ADJ.
MEMORY
DIMMER
PURE DIRECT
SELECT
1
1
Press the PICTURE ADJUST button.
• The image quality adjustment screen will appear.
STD
Returns the settings to the factory default settings.
M1 TO M5
Image quality settings that have been adjusted to your
preference can be stored to 5 memories, M1 to M5.
SET
SET permits set to setup level and setting of the
screen display position (horizontal and vertical).
P I CT URE MODE
PICTURE
ADJUST
STD
M1
M2
M3
M4
M5
PICT ADJ.
Remote control unit
Select the memory using the 2 cursor buttons (0, 1) and
press the ENTER button.
IMAGE QUALITY ADJUSTMENT 1
This permits adjustment of the contrast, brightness,
sharpness and hue. / Advance to Operation 3
IMAGE QUALITY ADJUSTMENT 2
2
MEMORY 1
0
This permits adjustment of the enhancer.
/ Advance to Operation 5.
GAMMA CORRECTION
59
2
M
This permits adjustment of the white level, black level
and chroma level. / Advance to Operation 4.
IMAGE QUALITY ADJUSTMENT 3
This is selected when dark portions of the image are
obscure, or bright portions are much brighter than
necessary. / Advance to Operation 6.
1
Remote control unit
0
3
H
0
0
0
SET
When Image Quality Adjustment 1 is selected and
adjusted:
• Press cursor button (ª), then select the image quality
adjustment item with cursor buttons (0, 1), set the
adjustment value with cursor buttons (•, ª), and press
the ENTER button.
• All of the adjusted contents will be stored.
CONTRAST (–6 to +6) (Factory default: 0)
2
M
• This adjusts the light/dark difference of the image.
BRIGHTNESS (0 to +12) (Factory default: 0)
3
1
MEMORY 1
0
0
3
H
0
0
0
• This adjusts the brightness of the image.
SHARPNESS (MID) (–6 to +6) (Factory default: 0)
• This adjusts the sharpness of the image for the
intermediate frequencies.
SHARPNESS (HIGH) (–6 to +6) (Factory default: 0)
• This adjusts the sharpness of the image for the high
frequencies. (Only effective for progressive images.)
HUE (–6 to +6) (Factory default: 0)
Remote control unit
• This adjusts the balance between green and red.
(This does not affect the component interlaced
output.)
4
1
MEMORY 1
When Image Quality Adjustment 2 is selected and
adjusted:
WHITE LEVEL (–5 to +5) (Factory default: 0)
• This adjusts the white level.
BLACK LEVEL (–5 to +5) (Factory default: 0)
• This adjusts the black level.
CHROMA LEVEL (–6 to +6) (Factory default: 0)
• This adjusts the density of the color.
0
0
2
3
2
3
0
Remote control unit
5
When Image Quality Adjustment 3 is selected and
adjusted:
ENHANCER (0 to +11) (Factory default: 0)
• This emphasizes the contour of the image.
DNR (Digital Noise Reduction) (0 to +3)
(Factory default: 0)
• This reduces video noise.
CCS (ON/OFF) (Factory default: OFF))
• This performs removal of the color signal component
for images in which the color signal component is
mixed with the brightness signal. (Only effective
with progressive images.)
60
1
MEMORY 1
E
0
Remote control unit
0
OFF
When Gamma Correction is selected and adjusted:
Two kinds of displays are prepared for adjustment of Gamma Correction.
• When use the Numerical table of Gamma Correction. (Figure 1)
:Pressing the cursor button (ª)
• When use the Graph of Gamma Correction. (Figure 2)
:Pressing the enter button
6
Remote control unit
Select the adjust point with cursor buttons (0, 1), set the adjustment brightness level with cursor buttons (•, ª), and press
the ENTER button.
(If the PICTURE ADJUST button is pressed before pressing the enter button, an adjustment level is not stored)
• The brightness level can be adjusted in range of 16 to 235.
• Pressing the cursor button (•) raises the level (and the image becomes brighter), and pressing the cursor button (ª) lowers
the level (and the image becomes darker).
• A press of the CLEAR button returns all of the setting points to the standard level.
✽ The level of the selected point cannot exceed the level of the points above and below that point.
(A dark portion cannot be set to exceed a portion that is brighter than it.)
1
MEMORY 1
G0
24
G1
32
G2
48
2
G3
64
G4
80
3
G5
96
G6
128
MEMORY 1
G7
160
G8
192
G9
224
235
GO : 0 2 4
0
0
100
(Figure 1)
(Figure 2)
✽ To exit the Image Quality Adjustment mode
Press the PICTURE ADJUST button.
REFERENCE:
• In the Graph of Gamma correction, the horizontal axis indicates the brightness level of the image that is recorded on the disc, and
the vertical axis indicates the brightness level of the image when it is output from this unit.
MEMORY 1
235
MEMORY 1
GO : 0 2 4
235
0
GO : 0 2 4
0
0
100
0
• When bright points of the disc side are
adjusted to the “dark” of the output side,
the fine parts of the bright portion that
normally become hard to see, become an
easily discerned image.
100
• When dark points of the disc side are
adjusted to the “bright” of the output side,
the fine parts of the dark portion that
normally become hard to see, become an
easily discerned image.
61
P I CT URE MODE
STD
7
When the Display Position is Selected and Adjusted:
• Press the cursor button (ª), then select the
horizontal/vertical direction with the cursor buttons (0,
1), set the adjustment value with the (•, ª) cursor
buttons, and press the ENTER button.
SETUP LEVEL (0 IRE, 0 IRE)
(Factory default: 0 IRE)
• This corrects floating black.
H. POSITION (–7 to +7) (Factory default: 0)
• A position adjustment is permitted left and right.
V. POSITION (–7 to +7) (Factory default: 0)
• A position adjustment is permitted up and down.
M1
M2
M3
M4
M5
SET
Remote control unit
P I C SE T UP
SE T UP LE VE L
0
0
0
✽ To exit the picture adjust mode
Press the PICTURE ADJUST button.
PICTURE MODE
STD(STANDARD)
M1(MEMORY1)
1(ADJUSTMENT 1)
CONTRAST
BRIGHTNESS
SHARPNESS(MID) ✽1
SHARPNESS(HI) ✽2
HUE ✽3
2(ADJUSTMENT 2)
WHITE LEVEL
BLACK LEVEL ✽2
CHROMA LEVEL
3(ADJUSTMENT 3)
ENHANCER ✽2
DNR
CCS ✽2
GAMMA
G0~G9
M2(MEMORY2)
M3(MEMORY3)
M4(MEMORY4)
M5(MEMORY5)
SETUP LEVEL
H.POSITION ✽2
V.POSITION ✽2
SET
✽1 This does not affect the HDMI/DVI output.
✽2 Only effective for HDMI, DVI and progressive scan.
✽3 This does not affect the interlaced of component video output.
62
12 USING THE VIDEO SETUP
2 The video output setting of the HDMI and the DVI-D connectors can be changed.
2 The video output setting of the PICTURE MODE, TV SYSTEM, SQUEEZE MODE and AUDIO ADJUST also can be changed.
POWER OFF
OPEN/CLOSE
PLAY
POWER ON
STOP
1
2
HDMI/DVI
SELECT
FORMAT
OPEN/
CLOSE
NTSC/PAL
SUPER AUDIO
CD SETUP
STILL / PAUSE
PROGRAM
/DIRECT
ON / STANDBY
VIDEO MODE
HDMI / DVI
SELECT
FORMAT
SUPER
AUDIO CD
SET UP
PURE
DIRECT
SELECT
CLEAR
SEARCH MODE
CALL
PUSH ENTER
DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER
DVD-A1XV
BACK LIGHT
ANGLE
TOP MENU
Display the setting mode
SUBTITLE
AUDIO
DISPLAY
1 2 3, 4
✽ The HDMI and DVI indicators flash when the connection is being checked, then stop flashing, once the check is completed.
1
Press the HDMI/DVI SELECT button.
• The modes described below will appear on the display.
HDMI/DVI OFF (Factory default)
Not output via the HDMI and DVI-D connectors. Set to “HDMI/DVI OFF”
when not connecting to these connectors.
HDMI Y Cb Cr
The Y Cb Cr format video signals and audio signals are output via the HDMI
connector.
The RGB format video signals are output via the DVI-D connector.
HDMI RGB
The RGB format video signals and audio signals are output via the HDMI
connector.
The RGB format video signals are output via the DVI-D connector.
✽ When connecting to the DVI device via the HDMI connector, signals are
output in RGB format regardless of whether “HDMI Y Cb Cr” or “HDMI
R G B” is set.
2
Press the HDMI/DVI FORMAT button.
• The modes described below will appear on the display.
Select the item you wish to set and define it.
480P/576P (Factory default)
Outputs the image via the HDMI or DVI-D connector at 480P or 576P.
720P
Outputs the image via the HDMI or DVI-D connector at 720P.
1080i
Outputs the image via the HDMI or DVI-D connector at 1080i.
AUTO
The performance of the HDMI device connected to the HDMI/DVI-D
connectors is detected automatically and the signals are output according to
the HDMI device’s panel resolution or maximum resolution. The panel
resolution or maximum resolution is selected according to the setting made
at “HDMI AUTO FORMAT” in the initial settings. (By factory default this is
set to “PANEL RES.”. (See pages 38, 41.) ) When a DVI device is connected,
the signals are output with a resolution of “480P/576P” automatically, so set
the resolution manually.
63
HDMI / DVI
SELECT
FORMAT
HDMI/DVI
SELECT
Main unit
FORMAT
Remote control unit
HDMI/DVI OFF
HDMI Y Cb Cr
HDMI R G B
HDMI / DVI
SELECT
FORMAT
HDMI/DVI
SELECT
Main unit
FORMAT
Remote control unit
480P/576P
720P
1080i
AUTO
3
Turning the VIDEO MODE knob.
• The modes described below will appear on the display.
Select the item you wish to set and press the VIDEO MODE knob to define
it.
PICTURE MODE
It is possible to select between five modes at which picture quality settings
are stored (M1 to M5) as well as the standard settings set upon shipment
from the factory. (See pages 59 ~ 62.)
TV SYSTEM
Select the video output connected to the TV or monitor whose image you
want to view.
On the DVD-A1XV, interlace output, progressive output and HDMI/DVI
output signals are each processed on independent video circuits. The audio
output is optimized for the selected video output, so choose the video
output you wish to view.
SQUEEZE MODE
The various modes that are selected in the VIDEO MODE are temporary.
The unit will return to the stored values when the power turns off.
AUDIO ADJUST
Depending on the connected device, the difference in the time required to
process the audio and video signals may result for example in the lips of
speaking characters not being synchronized with the sound. If this should
happen, this delay can be adjusted by offsetting the output of the audio
signals from the DVD-A1XV.
✽ For “TV SYSTEM” and “AUDIO ADJUST” selected at “VIDEO MODE”,
the change in the setting is stored in the memory. The same setting is
set when the power is turned off then back on.
✽ “PICTURE MODE” and “SQUEEZE MODE” selected at “VIDEO MODE”
are temporary changes. The settings return to those stored in the
memory as the default settings when the power is turned off then back
on.
VIDEO MODE
PUSH ENTER
Main unit
PICTURE MODE
TV SYSTEM
SQUEEZE MODE
AUDIO ADJUST
VIDEO MODE
4
When “PICTURE MODE” is selected:
• The modes described below will appear on the display.
Select the item you wish to set and press the VIDEO MODE knob to define
it. (See pages 59 ~ 62.)
STD (STANDARD)
Returns the settings to the factory default settings.
M1 (MEMORY1)
Picture quality adjustment items – M1 (MEMORY1) mode stored in the
picture quality adjustment mode.
M2 (MEMORY2)
Picture quality adjustment items – M2 (MEMORY2) mode stored in the
picture quality adjustment mode.
M3 (MEMORY3)
Picture quality adjustment items – M3 (MEMORY3) mode stored in the
picture quality adjustment mode.
M4 (MEMORY4)
Picture quality adjustment items – M4 (MEMORY4) mode stored in the
picture quality adjustment mode.
M5 (MEMORY5)
Picture quality adjustment items – M5 (MEMORY5) mode stored in the
picture quality adjustment mode.
64
PUSH ENTER
Main unit
STD(STANDARD)
M1 (MEMORY1)
M2 (MEMORY2)
M3 (MEMORY3)
M4 (MEMORY4)
M5 (MEMORY5)
4
When “TV SYSTEM” is selected:
• The modes described below will appear on the display.
Select the item you wish to set and press the VIDEO MODE knob to define
it.
PROGRESSIVE (Factory default)
The audio signals are synchronized with the progressive output.
(For component video output signals when “COMPONENT VIDEO OUT” at
“VIDEO SETUP” is set to “PROGRESSIVE”)
INTERLACED
The audio signals are synchronized with the interlaced output.
(For video output and S-video output signals, as well as for component video
output signals when “COMPONENT VIDEO OUT” at “VIDEO SETUP” is set
to “INTERLACED”)
HDMI/DVI
The audio signals are synchronized with the video signals output via the
HDMI/DVI connectors.
OTHERS
Select this when you want to view both the interlace output/progressive
output image and the HDMI/DVI output image at the same time.
The audio signals are set to the optimum timing for the interlace
output/progressive output image and the HDMI/DVI output image.
(Note, however, that the audio signals are not synchronized with the
interlace output/progressive output image and the HDMI/DVI output image.
To synchronize them, set to another position.)
When “SQUEEZE MODE” is selected:
• The modes described below will appear on the display.
Select the item you wish to set and press the VIDEO MODE knob to define
it.
OFF
Select this to display as full size of a 16:9 TV, regardless of the image’s size.
ON
Select this to display the image with a ratio of 4:3 at the center of a 16:9 TV,
regardless of the image’s size.
AUTO
Select this when playing back a 4:3 image, display images with a 4:3 aspect
ratio in the center of a 16:9 TV.
When “AUDIO ADJUST” is selected:
• The currently set time is shown on the display.
To change the set time, turn the VIDEO MODE knob, then press the knob.
Settable in units of 10 msec between –30 msec and +200 msec.
(+ direction: delay the sounds in the picture.)
The setting is reset to the default value (0 msec) when the “TV SYSTEM”
setting at “VIDEO SETUP” is switched.
65
VIDEO MODE
PUSH ENTER
Main unit
PROGRESSIVE
INTERLACED
HDMI/DVI
OTHERS
OFF
ON
AUTO
TIME:
0msec
TIME: +10msec
13 PLAYBACK
(1) Playback
3
2, 4
5
POWER OFF
POWER ON
HDMI/DVI
SELECT
FORMAT
1
2, 4
OPEN/
CLOSE
NTSC/PAL
SUPER AUDIO
CD SETUP
OPEN/CLOSE
PLAY
STOP
PROGRAM
/DIRECT
CLEAR
SEARCH MODE
STILL / PAUSE
CALL
BACK LIGHT
ON / STANDBY
VIDEO MODE
HDMI / DVI
SELECT
FORMAT
SUPER
AUDIO CD
SET UP
ANGLE
PURE
DIRECT
SELECT
SUBTITLE
AUDIO
TOP MENU
DISPLAY
MENU
RETURN
PUSH ENTER
DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER
DVD-A1XV
6
STOP
1
1
(Green)
1
Turn on the power.
• Press the power button, the power indicator lights
green and the power turns on.
When pressed again, the power turns off and indicator
is off.
• In the standby mode (the power indicator lights red),
press the ON/STANDBY button on the main unit or
POWER ON button on the remote control unit (RC-993).
(Red)
POWER ON
Remote control unit
OPEN/
CLOSE
Press the OPEN/CLOSE button to open the disc tray.
Main unit
Remote control unit
Set the disc in the disc tray.
OPEN/CLOSE
4
5
Main unit
ON / STANDBY
OPEN/CLOSE
3
PLAY
SLOW/SEARCH
ON / STANDBY
Main unit
2
STILL/PAUSE
SKIP
7
OPEN/
CLOSE
Press the OPEN/CLOSE button.
Main unit
66
Remote control unit
PLAY
PLAY
5
Press the PLAY button.
• For many interactive DVDs and video CDs with playback
control, a menu screen appears. In this case use the
procedure in step 6 to select the desired item.
✽ Interactive DVDs are DVDs including multiple angles,
stories, etc.
Main unit
Example: For DVDs with menu
screens
TOP MENU
Apple
Banana
Remote control unit
Example: For video CDs with
playback control
1. Opening
2. 1st movement
3. 2nd movement
6
7
Orange
Strawberry
Peach
Pineapple
Use the cursor buttons (•, ª, 0 and 1) to select the
desired item.
• For some discs there is a second menu screen. If so,
press the 9 button to display the next menu screen.
(See the disc’s jacket.)
✽ The cursor buttons (•, ª, 0 and 1) do not work for
video CDs. Use the number buttons to select the
desired item.
Press the ENTER button.
• The desired item is selected and playback starts.
• You can return to the menu screen by pressing the TOP
MENU/MENU button while the DVD is playing, though
this depends on the disc.
• Press the RETURN button during playback of a video CD
to return to the menu screen.
4. 3rd movement
5. Ending
Remote control unit
Remote control unit
Example: When “Apple” is
selected
TOP MENU
Apple
Banana
Orange
Strawberry
Peach
Pineapple
Apple
NOTES:
• Do not place more than one disc in the disc tray.
• The disc keeps turning while the menu screen is displayed
on the TV screen.
• If
appears on the TV screen while buttons are being
operated, that operation is not possible on the DVD-A1XV or
with that disc.
• Set the disc in the disc guide.
67
STOP button
SKIP buttons
HDMI/DVI
SELECT
FORMAT
OPEN/
CLOSE
NTSC/PAL
SUPER AUDIO
CD SETUP
STILL/PAUSE button
PROGRAM
/DIRECT
Number buttons
OPEN/CLOSE
PLAY
CLEAR
STOP
SEARCH MODE
CALL
SEARCH MODE button
BACK LIGHT
ANGLE
STILL / PAUSE
ON / STANDBY
SUBTITLE
AUDIO
TOP MENU
DISPLAY
MENU
RETURN
VIDEO MODE
HDMI / DVI
SELECT
FORMAT
SUPER
AUDIO CD
SET UP
PURE
DIRECT
SELECT
PUSH ENTER
DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER
DVD-A1XV
ENTER button
STOP button
STOP
STILL/PAUSE
PLAY
STILL/PAUSE button
SKIP
SKIP buttons
SLOW/SEARCH
SLOW/SEARCH buttons
PAGE
SLOW/SEARCH buttons
REPEAT
A-B
(2) Stopping Playback
During playback, press the STOP button on the main unit or the remote
control unit, playback stops and wall paper is displayed.
When “AUTO POWER MODE” is selected after 30 minutes in the stop
mode, the DVD-A1XV’s power automatically turns off and the standby mode
is set. (Auto Power Off) (See pages 54, 56.)
<Resume play memory function (DVD only)>
• With the DVD-A1XV, when the STOP button is pressed, that position is
stored in the memory. At this time, “1” flashes on the display. When the
PLAY button is pressed after pressing the STOP button, playback resumes
from the position at which it was stopped. The resume play memory
function is cancelled if the disc tray is opened or the STOP button is
pressed a second time.
STOP
STOP
Main unit
Remote control unit
✽ The resume play memory function only works for
discs for which the elapsed time is shown on the
display during playback.
NOTE:
• The resume play memory function does not work
during menu playback of DVD discs.
(3) Playing Still Pictures (Pausing)
STILL/PAUSE
During playback, press the STILL/PAUSE button on the main unit or the
remote control unit.
• Press the PLAY button to resume normal playback.
STILL / PAUSE
Main unit
Remote control unit
(4) Forward/Reverse Searching
SLOW/SEARCH
During playback, press one of the SLOW/SEARCH buttons on the main unit
or the remote control unit.
6 : Reverse direction
7 : Forward direction
• When pressed again, the search speed increases.
• Variable in 4 steps for Super audio CDs and CDs, 7 steps for DVD audio,
DVD video and video CD discs.
• Press the PLAY button to resume normal playback.
68
Main unit
Remote control unit
NOTE:
• In some cases the menu screen may reappear
when one of the SLOW/SEARCH buttons is
pressed during menu playback on a video CD.
(5) Skipping to the Beginning of Chapters or Tracks
Cueing using the SKIP buttons
During playback, press one of the SKIP buttons on the main unit or the
remote control unit.
8 : Reverse direction (PREVIOUS)
9 : Forward direction (NEXT)
• A number of chapters or tracks equal to the number of times the button is
pressed is skipped.
• When the SKIP 8 button is pressed once, the pickup returns to the
beginning of the currently playing chapter or track.
Playing position
Chapter/Track
Chapter/Track
Chapter/Track
SKIP
Main unit
Remote control unit
NOTE:
• In some cases the menu screen may reappear
when one of the SKIP buttons is pressed during
menu playback on a video CD.
Chapter/Track
Reverse direction , / Forward direction (direction of playback)
Cueing using the number buttons
Press the SEARCH MODE button during playback.
• The search mode switches each time the button is pressed.
For DVD audio discs : Group Æ Track Æ (Group) Æ
For DVD video discs : Title Æ Chapter Æ (Title) Æ
For Super audio CDs, CDs and video CDs : Track only
✽ The search mode set by pressing the SEARCH MODE button is stored
in the memory until the button is pressed again.
However, the search mode returns to the default mode when the power
is turned off.
• Use the number buttons to input the number to be played.
SEARCH MODE
Remote control unit
Remote control unit
NOTE:
• Some DVD audio, DVD video and video CD discs
do not operate as described in this manual due to
the intentions of the discs’ producers.
(6) Playing Frame by Frame (for DVD-videos and video CDs only)
During playback, press the STILL/PAUSE button on the main unit or the
remote control unit.
• The picture moves forward one frame each time the button is pressed.
• Press the PLAY button to resume normal playback.
• With DVD audio discs, forward frame-by-frame skipping is only possible for
the video part.
STILL/PAUSE
STILL / PAUSE
Main unit
Remote control unit
(7) Slow Playback (for DVD-videos and video CDs only)
In the still mode, press one of the SLOW/SEARCH buttons on the main unit
or the remote control unit.
6 : Reverse direction
7 : Forward direction
• When pressed again, the slow play speed increases.
For video CDs there are three steps.
• Press the PLAY button to resume normal playback.
• With DVD audio discs, the forward slow play function can only be used
with the video part.
69
SLOW/SEARCH
Main unit
Remote control unit
NOTE:
• Reverse slow play is not possible on video CDs.
(8) Selecting the still image (only for DVD-audios)
During playback, press the PAGE + or PAGE – button on the remote control
unit.
• For DVD audio discs with still images, the desired image can be selected.
• On some discs the image cannot be selected due to the intentions of the
discs’ producers.
PAGE
Remote control unit
(9) Playing bonus groups (only for DVD-audios)
SEARCH MODE
1
In the stop mode, press the SEARCH MODE button on the remote
control unit to set the search mode to “GROUP”.
Remote control unit
2
Use the number buttons to input the bonus group number.
Remote control unit
3
Use the number buttons on the remote control unit to input the
password (4 digits), then press the ENTER button.
• Playback starts from the first track in the specified group.
Remote control unit
• In some cases the password must be input at the menu screen. In these cases, follow the instructions on the screen.
• Once the password is input, the disc can be played as many times as you want until it is removed.
• If you make a mistake when inputting the password, press the CLEAR button on the remote control unit.
70
14 PLAYING REPEATEDLY
2 Use this function to play your favourite audio or video sections repeatedly.
Playing Repeatedly (Repeat Playback)
BACK LIGHT
ANGLE
SUBTITLE
DISPLAY
MENU
RETURN
STOP
STILL/PAUSE
SKIP
1
AUDIO
TOP MENU
PLAY
SLOW/SEARCH
PAGE
REPEAT
A-B
RANDOM
MARKER
ZOOM
SETUP
PICTURE
ADJUST
PICT ADJ.
MEMORY
DIMMER
PURE DIRECT
SELECT
RC-993
In the play mode, press the REPEAT button.
• The display on the TV screen switches each time the button is
pressed, and the corresponding repeat play mode or normal
playback mode is set.
REPEAT
Remote control unit
1
q For DVD audio discs
w For DVD video discs
• Normal playback
• Normal playback
• Normal playback
• Track repeated
• Chapter repeated
• Track repeated
TRACK REPEAT
CHAPTER REPEAT
TRACK REPEAT
• Group repeated
• Title repeated
GROUP REPEAT
TITLE REPEAT
• Repeat playback cancelled
REPEAT OFF
• Repeat playback cancelled
REPEAT OFF
e For video CDs, Super audio CDs and
music CDs
• Entire disc repeated
DISC REPEAT
• Repeat playback cancelled
REPEAT OFF
✽ To return to normal playback:
Return to normal playback by pressing the REPEAT button until “REPEAT OFF” appears on the TV screen.
71
Playing a Certain Section Repeatedly (A-B Repeat Playback)
BACK LIGHT
ANGLE
SUBTITLE
AUDIO
TOP MENU
DISPLAY
MENU
RETURN
STOP
STILL/PAUSE
SKIP
PLAY
SLOW/SEARCH
PAGE
1, 2
REPEAT
A-B
RANDOM
MARKER
ZOOM
SETUP
PICTURE
ADJUST
PICT ADJ.
MEMORY
DIMMER
PURE DIRECT
SELECT
RC-993
A TO B
SET A
A TO B
SET B
A-B
1
During playback, press the A-B button.
• This sets start point A.
Remote control unit
A-B
2
Press the A-B button again.
• This sets end point B, and repeat playback of the A-B section
starts.
Remote control unit
✽ To return to normal playback:
Press the A-B button until “A TO B CANCELED” appears on the TV screen.
NOTES:
• Repeat playback may not work for some DVDs.
• The repeat playback and A-B repeat playback functions will not work for DVDs and video CDs for which the elapsed time is not
shown on the display during playback.
• In some cases, subtitles may not be displayed near the A and B points during A-B repeat playback.
72
15 PLAYING TRACKS IN THE DESIRED ORDER
2 Use this function with DVD-AUDIO discs, video CDs, Super audio CDs and music CDs to play the tracks in the desired order.
2 This function does not affect with DVD-VIDEO discs.
HDMI/DVI
SELECT
OPEN/
CLOSE
FORMAT
NTSC/PAL
3
SUPER AUDIO
CD SETUP
PROGRAM
/DIRECT
2
OPEN/CLOSE
PLAY
1
CLEAR
STOP
SEARCH MODE
CALL
BACK LIGHT
ANGLE
SUBTITLE
AUDIO
TOP MENU
DISPLAY
MENU
RETURN
STILL / PAUSE
ON / STANDBY
VIDEO MODE
HDMI / DVI
SELECT
FORMAT
SUPER
AUDIO CD
SET UP
PURE
DIRECT
SELECT
PUSH ENTER
DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER
DVD-A1XV
STOP
STILL/PAUSE
SKIP
PLAY
3
SLOW/SEARCH
PROGRAM
NO.
TRACK
1
PROGRAM
/DIRECT
1
In the stop mode, press the PROGRAM/DIRECT
button once.
• The program selection screen appears.
Remote control unit
MODE
:
NORMAL
TOTAL T IME : - - : - -
INPUT : 0 - 9 , + 1 0
PROGRAM
Use the number buttons to select the track number
you want to program.
2
EX: To program track 5 and track 12
• Press the “5”.
• Press the “+10” and “2”.
• With DVD-audio, group numbers can be specified
and programmed. Bonus tracks, however, cannot
be programmed.
CL EAR : CL EAR BUT TON
Remote control unit
NO.
TRACK
1
2
3
05
12
__
MODE
:
NORMAL
INPUT : 0 - 9 , + 1 0
TOTAL T IME : 1 0 : 3 5
CL EAR : CL EAR BUT TON
PLAY
PLAY
3
Press the PLAY button.
• Playback of the tracks in the programmed order
begins.
Main unit
Remote control unit
✽ To return to normal playback:
Press the STOP button to stop programmed playback, then press the PROGRAM/DIRECT button.
Now press the PLAY button to start normal playback from the beginning of the disc.
✽ To clear tracks from the program:
Press the STOP button. The program play screen appears. Press the CLEAR button to clear the last track in the program.
✽ To clear the entire program:
The entire program is cleared when the power is turned off or the disc is ejected.
✽ To check the programmed contents, press the CALL button in the stop mode. The programmed contents are displayed step by
step.
✽ Up to 20 tracks can be programmed.
73
16 PLAYING TRACKS IN THE RANDOM ORDER
2 Use this function with video CDs, Super audio CDs and music CDs to play the tracks in random order.
With DVD-AUDIO discs, random playback is performed within the selected group.
2 This function does not affect with DVD-VIDEO discs.
HDMI/DVI
SELECT
FORMAT
OPEN/
CLOSE
NTSC/PAL
SUPER AUDIO
CD SETUP
PROGRAM
/DIRECT
2
2
CLEAR
SEARCH MODE
OPEN/CLOSE
PLAY
CALL
BACK LIGHT
STOP
ANGLE
SUBTITLE
AUDIO
TOP MENU
DISPLAY
MENU
RETURN
2
STILL / PAUSE
ON / STANDBY
VIDEO MODE
HDMI / DVI
SELECT
FORMAT
SUPER
AUDIO CD
SET UP
PURE
DIRECT
SELECT
STOP
STILL/PAUSE
PLAY
2
PUSH ENTER
DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER
DVD-A1XV
SKIP
SLOW/SEARCH
PAGE
1
REPEAT
A-B
RANDOM
MARKER
ZOOM
SETUP
PICTURE
ADJUST
PICT ADJ.
MEMORY
DIMMER
PURE DIRECT
SELECT
RANDOM
1
RANDOM ON
In the stop mode, press the RANDOM button.
• The random play screen appears.
Remote control unit
PLAY
PLAY
Press the PLAY button.
• The tracks start playing in random order.
Main unit
Remote control unit
2
✽ For DVD audio discs:
When operating from the remote control unit, use
the buttons to input the number of the group you
want to play.
SEARCH MODE
Remote control unit
✽ for DVD audio discs
• Random playback is not possible for some discs.
✽ To return to normal playback:
Press the STOP button to stop random playback, then press the RANDOM button once.
74
Remote control unit
HDMI/DVI
17 USING THE ON-SCREEN DISPLAY
SELECT
OPEN/
CLOSE
FORMAT
NTSC/PAL
SUPER AUDIO
CD SETUP
PROGRAM
/DIRECT
2 Use this function to display and change information on the disc
(titles, chapters, time, etc.)
3
CLEAR
SEARCH MODE
CALL
BACK LIGHT
ANGLE
SUBTITLE
TOP MENU
3
In the play mode, press the DISPLAY button.
• The On-Screen Display appears.
• The picture on the TV screen switches each time the button is pressed.
• The items displayed differ from disc to disc.
Example: For DVD audio discs
1
RETURN
DISPLAY
Remote control unit
Example: For video CDs, Super audio
CDs and music CDs
• Normal playback screen
• Normal playback screen
• Disc information screen
• Disc information screen
• Disc information screen
✽ SINGLE ELAPSED
05/ 10
02 : 11
01 : 10 : 59
SINGLE REMAIN
03 : 17
CHAPTER ELAPSED
00 : 00 : 01
TOTAL ELAPSED
26 : 15
CHAPTER REMAIN
00 : 40 : 59
TOTAL REMAIN
32 : 05
GROUP ELAPSED
0 : 00 : 01
TITLE
01/10
TITLE ELAPSED
CHAPTER 01 /10
00 : 00 : 01
GROUP REMAIN
0 : 57 : 59
TITLE REMAIN
TRACK ELAPSED
0 : 00 : 01
TRACK REMAIN
0 : 05 : 59
GROUP
01/02
AUDIO 1/1 : PPCM
3
MENU
1
2
• Normal playback screen
TRACK
01 /10
• Disc information screen
2
Example: For DVD video discs
AUDIO
DISPLAY
5.1 ch/ 96 kHz/24 BIT
TRACK
• Disc information screen
AUDIO 1/2 : DOLBY D3/2.1 ENGLISH
SUBTITLE
OFF
Use the • and ª cursor buttons to select the item you wish to change.
• The selected item is displayed with a yellow frame.
q For DVD audio discs
The elapsed time of groups and tracks can be selected.
w For DVD video discs
The elapsed time of titles, titles and chapters can be selected.
e For video CDs, Super audio CDs and music CDs
The elapsed time of tracks, tracks can be selected.
q Changing the elapsed time
Input using the number buttons, then press the ENTER button.
Example: For 1 minute 26 seconds / “00126” : DVD/SUPER AUDIO CD
“0126” : VIDEO CD/CD
w Changing the title, track or chapter
• For DVDs
Input using the number buttons, then press the ENTER button.
(For some discs it is not possible to change the title or chapter.)
• For video CDs, Super audio CDs and music CDs
Input using the number buttons. Playback starts from that track.
75
✽ Some Super audio CDs contain text
data. In this case, the album title and
artist are displayed in the stop mode,
and the title of the currently playing
track is displayed in the play mode.
Remote control unit
Remote control unit
Remote control unit
18 USING THE MULTIPLE AUDIO, SUBTITLE AND ANGLE FUNCTIONS
Switching the Audio Language (Multiple Audio Function)
2 With DVDs containing multiple audio language signals, the audio language can be switched during playback.
POWER OFF
POWER ON
HDMI/DVI
SELECT
FORMAT
OPEN/
CLOSE
NTSC/PAL
SUPER AUDIO
CD SETUP
PROGRAM
/DIRECT
CLEAR
SEARCH MODE
CALL
BACK LIGHT
ANGLE
SUBTITLE
AUDIO
TOP MENU
DISPLAY
MENU
RETURN
STOP
SKIP
STILL/PAUSE
1
2
PLAY
SLOW/SEARCH
AUDIO 1/3 :DOLBY D 3 /2.1 ENGLISH
AUDIO
1
During playback, press the AUDIO button.
• The current audio language number is displayed.
Remote control unit
AUDIO 2/3 :DOLBY D 3 /2.1 FRENCH
2
Use the • and ª cursor buttons to select the desired language.
• The display turns off when the AUDIO button is pressed.
Remote control unit
NOTES:
• With some discs it is not possible to change the audio language during playback. In such cases, select from the DVD menu. (See
page 79.)
• If the desired language is not set after pressing the • and ª cursor buttons several times, the disc does not include that language.
• The language selected in the default settings (See page 35.) is set when the power is turned on and when the disc is replaced.
76
Switching the Subtitle Language (Multiple Subtitle Function)
2 With DVDs containing multiple subtitle language signals, the subtitle language can be switched during playback.
POWER OFF
POWER ON
HDMI/DVI
SELECT
FORMAT
OPEN/
CLOSE
NTSC/PAL
SUPER AUDIO
CD SETUP
PROGRAM
/DIRECT
CLEAR
SEARCH MODE
CALL
BACK LIGHT
ANGLE
SUBTITLE
AUDIO
TOP MENU
DISPLAY
MENU
RETURN
STOP
SKIP
STILL/PAUSE
1
2
PLAY
SLOW/SEARCH
SUBTITLE : 01/ 0 3 ENGLISH
SUBTITLE
1
During playback, press the SUBTITLE button.
• The current subtitle language number is displayed.
Remote control unit
SUBTITLE : 02/ 0 3 FRENCH
2
Use the • and ª cursor buttons to select the desired language.
• The display turns off when the SUBTITLE button is pressed.
Remote control unit
NOTES:
• If the desired language is not set after pressing the • and ª cursor buttons several times, the disc does not include that language.
• The subtitle language set with the default settings (See pages 35, 36.) is set when the power is turned on and when the disc is
replaced.
If that language is not included on the disc, the disc’s default language is set.
• When the subtitle language is changed, several seconds may be required for the new language to appear.
• When a disc supporting the closed caption is played, the subtitle and the closed caption may overlap each other on the TV
monitor. In this case, turn the subtitle off.
77
Switching the Angle (Multiple Angle Function)
2 With DVDs containing multiple angle signals, the angle can be switched during playback.
POWER OFF
POWER ON
HDMI/DVI
SELECT
FORMAT
OPEN/
CLOSE
NTSC/PAL
SUPER AUDIO
CD SETUP
PROGRAM
/DIRECT
CLEAR
SEARCH MODE
CALL
BACK LIGHT
1
ANGLE
SUBTITLE
AUDIO
TOP MENU
DISPLAY
MENU
RETURN
STOP
STILL/PAUSE
SKIP
2
PLAY
SLOW/SEARCH
3/5
ANGLE
1
During playback, press the ANGLE button.
• The current angle number is displayed.
Remote control unit
4/5
2
Use the • and ª cursor buttons to select the desired angle.
• The display turns off when the ANGLE button is pressed.
Remote control unit
NOTES:
• The multiple angle function only works with discs on which multiple angles are recorded.
• “ANGLE” lights on the main unit’s display when playing a section recorded in the multi-angle mode.
• At scenes where multiple angles are recorded, the angle can be switched.
78
19 USING THE MENUS
Using the Top Menu
2 For DVDs containing multiple titles, the desired title can be selected and played from the top menu.
POWER OFF
POWER ON
HDMI/DVI
SELECT
OPEN/
CLOSE
FORMAT
NTSC/PAL
SUPER AUDIO
CD SETUP
PROGRAM
/DIRECT
2
CLEAR
SEARCH MODE
CALL
BACK LIGHT
ANGLE
1
2
SUBTITLE
AUDIO
TOP MENU
DISPLAY
MENU
RETURN
STOP
STILL/PAUSE
3
PLAY
Example:
TOP MENU
1
During playback, press the TOP MENU button.
• The top menu appears.
Remote control unit
TOP MENU
Apple
Banana
Orange
Strawberry
Peach
Pineapple
Example:
When “Orange” is selected
2
Use the cursor or number buttons to select the desired title.
• If you select the title number using the number buttons, skip step
3 below.
Remote control unit
Remote control unit
3
Press the ENTER button.
• Playback starts.
• Playback also starts if the PLAY button is pressed.
Remote control unit
79
TOP MENU
Apple
Banana
Orange
Strawberry
Peach
Pineapple
Using the DVD Menu
2 Some DVDs include special menus called DVD menus.
For example, DVDs with complex contents may contain guide menus, and DVDs with multiple languages may contain audio and
subtitle language menus.
These menus are called “DVD menus”.
Here we describe the general procedure for using DVD menus.
POWER OFF
POWER ON
HDMI/DVI
SELECT
OPEN/
CLOSE
FORMAT
NTSC/PAL
SUPER AUDIO
CD SETUP
PROGRAM
/DIRECT
2
CLEAR
SEARCH MODE
CALL
BACK LIGHT
ANGLE
2
1
SUBTITLE
AUDIO
TOP MENU
DISPLAY
MENU
RETURN
STOP
STILL/PAUSE
3
PLAY
SK
Example:
MENU
1
During playback, press the MENU button.
• The DVD menu appears.
DVD MENU
1. SUB TITLE
2. AUDIO
Remote control unit
3. ANGLE
Example:
“AUDIO” is selected
2
Use the cursor or number buttons to select the desired item.
• If you select the item using the number buttons, skip step 3
below.
Remote control unit
DVD MENU
1. SUB TITLE
2. AUDIO
3. ANGLE
Remote control unit
3
Press the ENTER button.
• The selected item is set.
• If more menus appear, repeat steps 2 and 3.
Remote control unit
80
20 MARKING SCENES YOU WANT TO SEE AGAIN
2 Set marks at scenes you want to see again so that you can start playback from the marked position whenever you want.
Setting Marks (for DVD-audios and DVD-videos only)
CLEAR
SEARCH MODE
CALL
BACK LIGHT
ANGLE
SUBTITLE
AUDIO
TOP MENU
DISPLAY
MENU
RETURN
3
STOP
STILL/PAUSE
SKIP
2, 3
PLAY
SLOW/SEARCH
PAGE
1
1
2
During playback, press the MARKER button.
• The marker screen appears.
• Use the 0 and 1 cursor buttons to select the “
marks.
• “ ” is displayed if the mark is not set.
REPEAT
A-B
RANDOM
MARKER
ZOOM
SETUP
PICTURE
ADJUST
PICT ADJ.
MEMORY
DIMMER
PURE DIRECT
SELECT
MARKER
”
Press the ENTER button at the scene you want to
mark.
• A number is displayed.
• Up to five marks can be set.
(To select another marker, use the cursor buttons
(0, 1).)
Remote control unit
Remote control unit
Calling Out Marked Scenes and Clearing Marks
3
Use the 0 and 1 cursor buttons to select the marker number and
press the ENTER button.
• If the marker screen is not displayed during playback, press the
MARKER button to display it.
Remote control unit
Remote control unit
✽ To clear the marker display:
Press the MARKER button.
✽ To clear a marker:
Use the 0 and 1 cursor buttons to select a marker number and press the
CLEAR button.
• You can clear existing markers, but they are restored when you open
the disc tray or switch the unit to standby.
NOTES:
• All the markers added with this unit are cleared when the unit is switched to standby or the disc tray is opened.
• Depending on where the marker is set, subtitles may not be displayed.
81
21 PLAYING IN THE ZOOM MODE
BACK LIGHT
ANGLE
2
SUBTITLE
AUDIO
TOP MENU
DISPLAY
MENU
RETURN
STOP
STILL/PAUSE
SKIP
PLAY
SLOW/SEARCH
PAGE
REPEAT
A-B
RANDOM
MARKER
ZOOM
SETUP
PICTURE
ADJUST
PICT ADJ.
MEMORY
DIMMER
PURE DIRECT
SELECT
1
RC-993
1
2
In the play or pause mode, press the ZOOM button.
• The zoom rate increases each time the ZOOM button is pressed.
For DVD video discs and video CDs:
OFF Æ x1.5 Æ x2 Æ x4 Æ OFF
For DVD audio discs:
OFF Æ x2 Æ x4 Æ OFF
ZOOM
Remote control unit
Use the cursor buttons (ª, •, 0 and 1) to move the zoomed picture.
Remote control unit
NOTES:
• Zooming is not possible with some discs.
• The zoom function may not work properly at some scenes.
• Zooming is not possible at the top menu or the menu screen.
• When the picture is enlarged, the picture quality may be decreased and the picture may be blurred.
82
22 PLAYING MP3
Listening to MP3 CD, CD-Rs and CD-RWs
2 There are many music distribution sites on the internet from which music files in MP3 format can be downloaded. Music downloaded
as instructed on the site and written onto a CD-R/RW disc can be played on the DVD-A1XV.
If music recorded on commercially available music CDs is converted on a computer into MP3 files using an MP3 encoder (conversion
software), the data on a 12 cm CD is reduced into about 1/10 the amount of the original data. Thus, when written in MP3 format, the
data of about 10 music CDs can fit onto the one CD-R/RW disc. The one CD-R/RW disc can contain over 100 tracks.
✽ Values when 5-minute tracks are converted with a standard bit rate of 128 kbps into MP3 files and using a CD-R/RW disc with a
capacity of 650 MB.
✽ Uses of recordings you have made other than for your personal enjoyment are not permitted under the Copyright Law
without permission of the copyright holder.
HDMI/DVI
1
1
SELECT
3
FORMAT
OPEN/
CLOSE
1
NTSC/PAL
SUPER AUDIO
CD SETUP
PROGRAM
/DIRECT
CLEAR
OPEN/CLOSE
PLAY
STOP
SEARCH MODE
CALL
BACK LIGHT
ANGLE
STILL / PAUSE
ON / STANDBY
SUBTITLE
AUDIO
TOP MENU
DISPLAY
MENU
RETURN
VIDEO MODE
HDMI / DVI
SELECT
FORMAT
SUPER
AUDIO CD
SET UP
PURE
DIRECT
SELECT
2, 3
PUSH ENTER
DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER
DVD-A1XV
STOP
SKIP
STILL/PAUSE
PLAY
3
SLOW/SEARCH
OPEN/CLOSE
1
Load the CD-R/RW disc on which the MP3 format
music files have been written into the DVD-A1XV.
(See page 30.)
• When the disc is loaded in the DVD-A1XV, the disc
information screen appears.
D I SC I NF ORMATION
ROOT
Main unit
OPEN/
CLOSE
• If there are multiple folders, proceed to step 2.
• If there are no folders on the disc, proceed to step
3.
PL AY MODE
S I NGLE E L APSED
SE L EC T :
ROOT
0
F OL DE R1
1
F OL DE R 2
2
F OL DE R 3
3
F OL DE R 4
4
F OL DE R 5
5
F OL DE R
: --:-DE C I S I ON : ENTE R BUT TON
Remote control unit
Use the cursor buttons (ª, •, 0 and 1) to select the
folder containing the file(s) you want to play, then
press the ENTER button.
2
✽ To change the folder
Use the cursor buttons to select “ROOT”, then
press the ENTER button. The screen in step 1
reappears. Select the desired folder.
D I SC I NF ORMATI ON
Remote control unit
ROOT
••
0
F OL DE R1
MP3 _ 0 1
1
F OL DE R 2
MP3 _ 0 2
2
F OL DE R 3
MP3 _ 0 3
3
F OL DE R 4
MP3 _ 0 4
4
F OL DE R 5
MP3 _ 0 5
5
PL AY MODE
S I NGLE E L APSED
SE L EC T :
Remote control unit
83
F OL DE R
: --:-DE C I S I ON : ENTE R BUT TON
Use the • and ª cursor buttons to select the MP3
file you want to play, then press the PLAY button or
ENTER button.
• Playback starts.
✽ The display can be switched between the single
elapsed time and the single remaining time and
the track name by pressing the DISPLAY button.
✽ Programmed playback is not possible with MP3
discs.
3
✽ To change the MP3 file
Press the STOP button, then use the • and ª
cursor buttons to reselect the desired MP3 file.
✽ To set the random play mode
In the stop mode, press the RANDOM button.
Then press the PLAY button or ENTER button.
✽ To set the repeat mode
The repeat mode changes each time the REPEAT
button is pressed.
D I SC I NF ORMATION
Remote control unit
PLAY
••
0
MP3 _ 0 1
1
F OL DE R 2
MP3 _ 0 2
2
F OL DE R 3
MP3 _ 0 3
3
F OL DE R 4
MP3 _ 0 4
4
F OL DE R 5
MP3 _ 0 5
5
PL AY MODE
S I NGLE E L APSED
SE L EC T :
F OL DE R
: --:-DE C I S I ON : ENTER BUT TON
Main unit
FOLDER
TRACK REPEAT
FOLDER REPEAT
✽ To return to the initial disc information screen
Press the STOP button, use the cursor button to
select “ROOT”, then press the ENTER button.
The screen in step 1 reappears.
ROOT
F OL DE R1
PLAY
Remote control unit
NOTES:
• The DVD-A1XV is compatible with the “MPEG-1 Audio Layer 3” standards (sampling frequency of 44.1 kHz or 48 kHz). It is not
compatible with such other standards as “MPEG-2 Audio Layer 3”, “MPEG-2.5 Audio Layer 3”, MP1, MP2, etc.
• It may not be possible to play some CD-R/RW discs due to disc properties, dirt, warping, etc.
• The digital signals output when playing MP3 files are MP3 signals converted into PCM, regardless of whether the audio output
presetting is set to “NORMAL” or “PCM”. The signals are output with the same sampling frequency as that of the music source.
• In general, the higher an MP3 file’s bit rate, the better the sound quality. On the DVD-A1XV, we recommend using MP3 files
recorded with bit rates of 128 kbps or greater.
• MP3 files may not be played in the expected order, since the writing software may change the position of the folders and the
order of the files when writing them on the CD-R/RW.
• Programmed playback are not possible with MP3 discs.
• When writing MP3 files on CD-R/RW discs, select “ISO9660 level 1/ level 2” as the writing software format. This may not be
possible with some types of writing software. For details, refer to the writing software’s usage instructions.
• The number of files playable with the DVD-A1XV is approximately 600 or less.
• With the DVD-A1XV it is possible to display folder names and file names on the screen like titles. The DVD-A1XV can display up
to 8 characters, consisting of numbers, capital letters, and the “_” (underscore) mark.
• If recorded in a format other than “ISO9660 level 1”, normal display and playback may not be possible. In addition, folder and file
names including other symbols will not be displayed properly.
• Be sure to add the extension “.MP3” to MP3 files. Files cannot be played if they have any extension other than “.MP3” or if they
have no extension. (with Macintosh computers, MP3 files can be played by adding the extension “.MP3” after the file name
consisting of up to 8 capital or numbers and recording the files on the CD-R/RW.)
• Do not apply stickers, tape, etc., to either the label side or the signal side of CD-R/RW discs. If adhesive gets on the surface of
a disc, the disc may get stuck inside the DVD-A1XV and be impossible to eject.
• The DVD-A1XV is not compatible with packet write software.
• The DVD-A1XV is not compatible with ID3-Tag.
• The DVD-A1XV is not compatible with play lists.
• The DVD-A1XV is not compatible with MP3 PRO.
• Do not play CD-R/RW discs containing any files other than music CD files (in CDDA format), WMA, MP3 and JPEG files. Doing
so may result in malfunction or damage, depending on the type of file.
84
23 PLAYING WMA
2 Listening to WMA (Windows Media Audio) CD-R/CD-RW
• This unit can play CD-R/RW music files that have been recorded in the WMA (Windows Media Audio)* audio compression format.
Windows Media and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the
United States and/or other countries.
✽ WMA (Windows Media Audio): Audio coding of Microsoft Corporation.
✽ Uses of recordings you have made other than for your personal enjoyment are not permitted under the Copyright Law without
permission of the copyright holder.
• The method of playback is the same as “Listening to MP3 CD, CD-Rs and CD-RWs” on Pages 83, 84.
• In the file display of the disc information screen, WMA files will be displayed with the “WMA” icon instead of the “MP3” icon. (Files
for which the “WMA” icon is not displayed cannot be played. There will be a skip and the next file with an icon will be played.)
NOTES:
• Files recorded with a sampling frequency of 44.1 kHz, and 48 kHz are supported.
• Programmed playback cannot be performed with WMA discs.
• The digital output at the time of WMA file playback is converted to PCM regardless of the initial settings.
• Please use discs that have been recorded in conformity with the ISO 9660 level 1/level 2 CD-ROM file system. (Extended formats
are excluded.)
• Copyright protected files cannot be played. Also note that depending on the writing software and conditions, playback might not
be possible, or the files might not be displayed properly.
• Playback of the CD-R/RW might not be possible depending on the disc characteristics, soiling, scratches, and other factors.
• Bit rates of 64 k to 160 kbps are supported for WMA files that have an extension of “.wma” or “.WMA”.
• This unit can display the folder names and file names on the screen. Up to 11 half-width alphanumeric upper case characters and
symbols (including the underscore symbol) can be displayed. Kanji, hiragana, katakana and other characters cannot be displayed.
• While in the stop condition, the DISPLAY button of the remote control can be used to switch and display the title names and the
artist names. (One folder has a capacity of up to 99 files.)
• Recorded discs with no more than 99 files per folder are recommended. Multiple folder configurations are possible; however,
depending on the configuration, recognition and playback of all the folders and files might not be possible.
• Multi-session discs can also be played back, however, playback of discs that have had session closure within 10 sessions.
• Direct track selection using the remote control numerical keys (0 to 9, and +10) can specify up to 179 tracks (179 files) per folder.
When 179 tracks are exceeded, while the unit is stopped, use the cursor buttons at the disc information screen to select the
files, and use the play button or the ENTER button to play.
85
24 PLAYING STILL PICTURE FILES (JPEG FORMAT)
2 JPEG files stored on Kodak picture CDs, Fujicolor CDs, CD-Rs and CD-RWs can be played as a slide show and enjoyed on the DVD-A1XV.
Playing still picture
2 Kodak picture CDs and Fujifilm Fujicolor CDs can be played on the DVD-A1XV.
When a CD (recording still picture) is played, the photographs on the CD can be
displayed on a TV.
(“Picture CD” and “Fujicolor CD” are service by which photographs taken on
conventional silver film cameras are converted into digital data and written on
CDs. For details on Kodak picture CD, contact a store that offers Kodak
development services. For details about Fujicolor CDs, please contact a store
offering Fuji Photo Film developing services.)
POWER OFF
POWER ON
HDMI/DVI
SELECT
FORMAT
OPEN/
CLOSE
NTSC/PAL
SUPER AUDIO
CD SETUP
1-q, w
PROGRAM
/DIRECT
CLEAR
SEARCH MODE
CALL
BACK LIGHT
ANGLE
1-q, w 1-q, w
SUBTITLE
AUDIO
TOP MENU
DISPLAY
MENU
RETURN
1-w 1-q, w
OPEN/CLOSE
PLAY
1-w
STOP
STOP
1-q, w
STILL/PAUSE
SKIP
PLAY
1-w
SLOW/SEARCH
STILL / PAUSE
PAGE
REPEAT
ON / STANDBY
VIDEO MODE
HDMI / DVI
SELECT
FORMAT
SUPER
AUDIO CD
SET UP
A-B
RANDOM
MARKER
ZOOM
SETUP
PICTURE
ADJUST
PICT ADJ.
MEMORY
PURE
DIRECT
SELECT
DIMMER
PURE DIRECT
SELECT
PUSH ENTER
DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER
1
DVD-A1XV
q Load the Kodak picture CD into the DVD-A1XV.
• When the disc is loaded, a slide show of the still pictures begins automatically.
• The slide show continues until the STOP button is pressed.
w Load the Fujicolor CD into the DVD-A1XV.
• When the disc is loaded, a maximum of 9 still pictures are displayed automatically.
• Press the PLAY or ENTER button , the slide show begin. The slide show continues until the STOP button is pressed.
Playing still pictures stored on CD-Rs/RWs
HDMI/DVI
1
1
3
SELECT
FORMAT
OPEN/
CLOSE
NTSC/PAL
SUPER AUDIO
CD SETUP
1
PROGRAM
/DIRECT
CLEAR
OPEN/CLOSE
PLAY
STOP
SEARCH MODE
CALL
BACK LIGHT
ANGLE
STILL / PAUSE
ON / STANDBY
SUBTITLE
AUDIO
TOP MENU
DISPLAY
MENU
RETURN
VIDEO MODE
HDMI / DVI
SELECT
FORMAT
SUPER
AUDIO CD
SET UP
PURE
DIRECT
SELECT
PUSH ENTER
DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER
2, 3
DVD-A1XV
STOP
STILL/PAUSE
PLAY
3
SKIP
SLOW/SEARCH
D I SC I NF ORMATI ON
1
Load the CD-R/RW on which the still pictures have been written into
the DVD-A1XV.
• When the disc is loaded in the DVD-A1XV, the disc information
screen appears.
• If there are multiple folders, proceed to step 2.
• If there are no folders on the disc, proceed to step 3.
ROOT
PL AY MODE
S I NGLE E L APSED
SE L EC T :
86
ROOT
0
JPEG 1
1
JPEG 2
2
JPEG 3
3
JPEG 4
4
JPEG 5
5
F OL DE R
: --:-DE C I S I ON : ENTER BUT TON
Use the • and ª cursor buttons to select the folder
containing the file(s) you want to play, then press the
ENTER button.
2
D I SC I NF ORMATI ON
✽ To change the folder
Use the cursor button to select “ROOT”, then
press the ENTER button. The screen in step 1
reappears. Select the desired folder.
ROOT
••
0
JPEG 1
A
1
JPEG 2
B
2
JPEG 3
C
3
JPEG 4
D
4
JPEG 5
E
5
PL AY MODE
S I NGLE E L APSED
SE L EC T :
F OL DE R
: --:-DE C I S I ON : ENTER BUT TON
Remote control unit
D I SC I NF ORMATION
3
Use the • and ª cursor buttons on the remote
control unit to select the still picture file from which
you want to start the slide show, then press the
PLAY button or the ENTER button on the remote
control unit.
• The slide show starts.
• Only the still picture files in the selected folder are
played.
✽ Once all the still picture files in the folder have
been played, the disc information screen
reappears.
ROOT
••
0
JPEG 1
A
1
JPEG 2
B
2
JPEG 3
C
3
JPEG 4
D
4
JPEG 5
E
5
PL AY MODE
S I NGLE E L APSED
SE L EC T :
Remote control unit
F OL DE R
: --:-DE C I S I ON : ENTER BUT TON
PLAY
PLAY
Main unit
Remote control unit
✽ To view several of the still pictures stored on the disc at once:
• To select and view a still picture (to start the slide show from a specific still picture), use the cursor buttons (ª, •, 0 and 1) to
select the desired still picture, then press the ENTER button.
✽ To temporarily stop the slide show:
• Press the STILL/PAUSE button.
• To resume the slide show, press the PLAY button.
✽ To cue a still picture you want to view (from which you want to start the slide show):
• During the slide show, press one of the SKIP (8, 9) buttons. Press the SKIP 8 button to cue back to the previous still
picture, the SKIP 9 button to cue ahead to the next still picture.
✽ Flipping and rotating still pictures:
• Use the cursor buttons (ª, •, 0 and 1) to flip the still picture.
• cursor button: The currently displayed still picture is flipped vertically.
ª cursor button: The currently displayed still picture is flipped horizontally.
0 cursor button: The currently displayed still picture is rotate 90° counterclockwise.
1 cursor button: The currently displayed still picture is rotate 90° clockwise.
✽ Play the image in the zoom mode.
• When the ZOOM button is pressed while playing a JPEG image (“ZOOM ON” is displayed on the screen at this time) zoom in
and zoom out using the search keys.
6: zoom out, 7: zoom in
• When the image is zoomed, use the cursor buttons (ª, •, 0 and 1) to move the zoomed picture.
• Continuous playback (SLIDE SHOW) is not possible in the zoom mode.
• Zooming is not possible with files that have a low resolution.
✽ The way of switching to the next image during continuous JPEG image playback (SLIDE SHOW) can be selected.
• Preset the SEARCH MODE button on the remote control unit.
• Select from SLIDE SHOW MODE:1 to MODE: 11, MODE: RAND and MODE: NONE.
87
Special play modes for WMA and MP3 and JPEG files
Use the 0 and 1 cursor buttons to select the play mode, the • and ª cursor buttons to select the special play mode.
• FOLDER (the WMA and MP3 and JPEG files in the folder are played in order starting from the selected file)
• FOLDER REPEAT (all the WMA and MP3 and JPEG files in the folder are played repeatedly starting from the selected file)
• DISC (all the WMA and MP3 and JPEG files on the disc are played in order starting from the selected file)
• DISC REPEAT (all the WMA and MP3 and JPEG files on the disc are played repeatedly starting from the selected file)
• RANDOM ON (all the WMA and MP3 and JPEG files in the folder are played in random order starting from the selected file)
• TRACK REPEAT (the select WMA or MP3 or JPEG file is played repeatedly)
NOTES:
• The DVD-A1XV is compatible with image data stored in JPEG format, but Denon does not guarantee that all image data stored
in JPEG format can be viewed.
• Files with sizes of up to 30 Mbytes can be displayed.
• It may not be possible to play some CD-Rs/RWs due to disc properties, dirt, scratches, etc.
• When storing JPEG files on the CD-R/RW, set the writing program to store the files in the “ISO9660 level 1/ level 2” format.
• Be sure to give JPEG files the extension “.JPG” and “.JPE”. Files with other extensions or with no extensions cannot be viewed
on the DVD-A1XV.
• Do not apply stickers, tape, etc., to either the label side or the signal side of CD-R/RW discs. If adhesive gets on the surface of
a disc, the disc may get stuck inside the DVD-A1XV and be impossible to eject.
• Do not play CD-R/RW discs containing any files other than music CD files (in CDDA format), WMA, MP3 and JPEG files. Doing
so may result in malfunction or damage, depending on the type of file.
• JPEG files written using Macintosh computers cannot be played.
88
25 TROUBLESHOOTING
Check again before assuming the player is malfunctioning
2 Are all the connections correct ?
2 Are you following the instructions in the manual ?
2 Are the amplifier and speakers operating properly ?
If the DVD-A1XV does not seem to be functioning properly, check the table below. If this does not solve the problem, the DVD-A1XV may
be damaged. Turn off the power, unplug the power cord from the power outlet, and contact your store of purchase or nearest Denon
sales office.
Symptom
Power does not turn on.
Check
• Plug the power supply cord securely into the power outlet.
Page
12~22,
25
Playback does not start when PLAY
button is pressed.
Playback stops immediately.
• Is there condensation on the disc or player ? (Let stand for 1 or 2 hours.)
• Discs other than DVDs,SuperAudio CDs, video CDs and music CDs cannot be played.
• Disc is dirty. Wipe off the dirt.
Picture does not appear.
• Check the connections.
• Check that VIDEO OUT has not been set to “VIDEO OUT:OFF” or “ALL OFF” for PURE
DIRECT MODE.
• Set the TV’s input to “video”.
12~22
57, 58
• Check the connections.
• Properly set the input of the TV, stereo, etc.
• Check the “DIGITAL OUTPUT” and “COMPRESSION” settings.
12~22
–
46, 50,
51
16, 17,
19, 20,
16, 17,
58
57, 58
Sound is not produced or sound quality
is poor.
• Digital signals cannot be output with Super audio CDs. Use analog or IEEE1394
connections.
• Area/layer of Super audio CD being played (MULTI/STEREO/CD) does not match amplifier
connections.
• When the video output setting at “PURE DIRECT” is set to “VIDEO OUT : OFF” or “ALL
OFF”, no sound at HDMI connector.
• When a device not compatible with HDMI specification Ver. 1.1 is connected via an HDMI
connector, the audio signals of DVD audio discs copyright-protected by CPPM are not
output.
–
10
11
–
21
Menu playback of video CD’s is not
possible.
• Menu playback is not possible with anything but video CDs with playback control.
Picture is disturbed during the search
operation.
• Some disturbance is normal.
Buttons do not operate.
• Some operations are disabled for some discs.
No subtitles are displayed.
• Subtitles are not displayed for DVDs not containing subtitles.
• Subtitles are turned off. Turn the subtitles setting on.
–
35, 36
• The audio (or subtitle) language does not switch for discs which do not include multiple
audio (or subtitle) languages.
• For some discs the audio (or subtitle) language cannot be switched when the operation to
switch it is performed, but can be switched on the menu screens.
76, 77
Audio (or subtitle) language does not
switch.
Angle does not switch.
• The angle cannot be switched for DVDs which do not contain multiple angles. In some
cases multiple angles are only recorded for specific scenes.
Playback does not start when the title is
selected.
• Check the “RATINGS” setting.
67
–
67
80
78
52, 53
• While the player is in the stop mode, hold the player’s SKIP 9 button and the PLAY
button down simultaneously and then hold the OPEN/CLOSE button down for longer than
3 seconds (until “INITIALIZE” disappears from the TV monitor).
The lock will be released and all default settings and picture settings will return to the
default values.
–
The disc is not played with the audio or
subtitle language set as the default
setting.
• The disc does not play with the selected audio or subtitle language if that audio or subtitle
language is not included on that DVD.
35~37
Picture is not displayed in 4:3 (or 16:9).
• Set the “TV ASPECT” default setting to the proper setting for the connected TV.
The password for rating level has been
forgotten.
Reset all the setting to Factory
Preset.
89
43
Symptom
Menu screen messages for the desired
language do not display.
An image is not projected with an
HDMI/DVI connection.
Picture and sound are interrupted with
HDMI/DVI connections.
Remote control unit does not operate.
Check
Page
• Check the setting of “DISC MENUS” under “LANGUAGE SETUP” in “SETUP”.
35~37
• Check the HDMI/DVI connection.(Check the status of the HDMI/DVI indicators.)
• Check whether the connected monitor equipment or other equipment supports HDCP. (The
DVD-A1XV will not output a video signal unless the connected equipment supports HDCP.)
• Check the settings of “HDMI/DVI SELECT”.
• Check whether the output format of the DVD-A1XV (HDMI/DVI FORMAT) matches the input
format of the connected equipment.
• Check whether the video output setting at “PURE DIRECT” is set to “VIDEO OUT : OFF”
or “ALL OFF”.
25
20~22
• When the “HDMI/DVI FORMAT” setting is set to “AUTO”, the picture or sound may be
interrupted when cables are connected or disconnected or depending on the conditions of
the connected device(s).
63
•
•
•
•
27
27
27
27
Check that the batteries are inserted in the proper “<” and “>” directions.
The batteries are dead. Replace them with new batteries.
Point the remote control unit at the remote control sensor when operating it.
Operate the remote control unit within a distance of 7 meters from the remote control
sensor.
• Remove the obstacle between the remote control unit and remote control sensor.
90
63
20~22
57, 58
27
26 MAIN SPECIFICATIONS
Signal system:
Applicable discs:
S-Video output:
Video output:
Component output:
HDMI output:
DVI output:
RGB output:
Audio output:
Audio output properties:
Digital audio output:
Power supply:
Power consumption:
Maximum external
dimensions:
Mass:
2 Remote control unit:
Type:
Power supply:
NTSC/PAL
(1) DVD-Audio/DVD-Video discs
1-layer 12 cm single-sided discs, 2-layer 12 cm single-sided discs, 2-layer 12 cm double-sided discs
(1 layer per side)
1-layer 8 cm single-sided discs, 2-layer 8 cm single-sided discs, 2-layer 8 cm double-sided discs
(1 layer per side)
(2) Super audio CDs
Single layer 12 cm discs, Dual layer 12 cm discs, Hybrid layer 12 cm discs
(3) Compact discs (CD-DA, Video CD)
12 cm discs, 8 cm discs
Y output level
: 1 Vp-p (75 Ω/ohms)
C output level: 0.3 Vp-p (75 Ω/ohms)
Output connector
: S connectors, 2 sets / AV 1 connector, 1 set
Output level
: 1 Vp-p (75 Ω/ohms)
Output connector
: Pin jacks, 2 sets / AV 1 connector, 1 set
Y output level
: 1 Vp-p (75 Ω/ohms)
PB/CB output level
: 0.7 Vp-p (75 Ω/ohms)
PR/CR output level
: 0.7 Vp-p (75 Ω/ohms)
Output connector
: Pin jack, 1 set / BNC jack, 1set
Output connector
: HDMI connector, 1 set
Output connector
: DVI-D connector, 1 set
Output level
: 0.7 Vp-p (75 Ω/ohms)
Output connector
: AV 1 connector, 1 set
Output level
: 2 Vrms
2 channel (L, R) output connector : Pin jack, 1 set
AV 1 connector, 1 set
Multi channel (FL, FR, C, SW, SL, SR) output connector : Pin jack, 1 set
(1) Frequency response
q DVDs (linear PCM)
: 2 Hz to 22 kHz (48 kHz sampling)
: 2 Hz to 44 kHz (96 kHz sampling)
: 2 Hz to 88 kHz (192 kHz sampling)
w Super audio CDs
: 2 Hz to 100 kHz
e CDs
: 2 Hz to 20 kHz
(2) S/N ratio
: 125 dB
(3) Total harmonic distortion : 0.0008 %
(4) Dynamic range
: 112 dB
Optical digital output : Optical connector, 1 set
Coaxial digital output : Pin jack, 1 set
DENON LINK output : DENON LINK connector, 1 set
IEEE 1394 terminal : IEEE 1394 connectors, 2 sets
AC 230 V, 50 Hz
80 W
434 (width) x 170 (height) x 432 (depth) mm (including protruding parts)
19 kg
RC-993
Infrared pulse
DC 4.5 V, 3 R6P/AA batteries
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights.
Use of this copyright protection technology must be authorized by Macrovision , and is intended for home and other limited viewing
uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
✽ Design and specifications are subject to change without notice in the course of product improvement.
91
TOKYO, JAPAN
www.denon.com
00D 511 4289 013
Download PDF

advertising