FujiFilm REAL 3D W1 Digital Camera User Manual

BL00963-200
EN
Before You Begin
First Steps
Owner’s Manual
Thank you for your purchase of this
product. This manual describes how
to use your FUJIFILM REAL 3D W1
digital camera and the supplied software. Be sure that you have read and
understood its contents before using
the camera.
Basic Photography and Playback
More on Photography
More on Playback
Movies
Connections
Menus
For information on related products, visit our website at
http://www.fujifilm.com/products/index.html
Technical Notes
Troubleshooting
Appendix
For Your Safety
IMPORTANT SAFETY INSTRUCTIONS
• Read Instructions: All the safety and operating instructions should be read
before the appliance is operated.
• Retain Instructions: The safety and
operating instructions should be
retained for future reference.
• Heed Warnings: All warnings on the
appliance and in the operating instructions should be adhered to.
• Follow Instructions: All operating and
use instructions should be followed.
Alternate Warnings: This video product is equipped with a three-wire
grounding-type plug, a plug having
a third (grounding) pin. This plug
will only fit into a grounding-type
power outlet. This is a safety feature.
If you are unable to insert the plug
into the outlet, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of
the grounding type plug.
Water and Moisture: Do not use this
video product near water—for example, near a bath tub, wash bowl,
kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool,
and the like.
Power-Cord Protection: Power-supply cords should be routed so that
they are not likely to be walked on
or pinched by items placed upon
or against them, paying particular
Overloading: Do not overload wall out- attention to cords at plugs, conveInstallation
Power Sources: This video product lets and extension cords as this can nience receptacles, and the point
should be operated only from the result in a risk of fire or electric shock. where they exit from the appliance.
type of power source indicated on Ventilation: Slots and openings in Accessories: Do not place this video
the marking label. If you are not sure the cabinet are provided for ventila- product on an unstable cart, stand,
of the type of power supply to your tion, to ensure reliable operation of tripod, bracket, or table. The video
home, consult your appliance dealer the video product and to protect it product may fall, causing serious inor local power company. For video from overheating, and these open- jury to a child or adult, and serious
products intended to operate from ings must not be blocked or cov- damage to the appliance. Use only
battery power, or other sources, refer ered. The openings should never with a cart, stand, tripod, bracket, or
to the operating instructions.
be blocked by placing the video table recommended by the manufacGrounding or Polarization: This video product on a bed, sofa, rug, or other turer, or sold with the video product.
Any mounting of the appliance should
product is equipped with a polar- similar surface.
ized alternating-current line plug (a This video product should not be follow the manufacturer’s instructions,
plug having one blade wider than placed in a built-in installation such and should use a mounting accessory
the other). This plug will fit into the as a bookcase or rack unless proper recommended by the manufacturer.
power outlet only one way. This is a ventilation is provided or the manu- An appliance and
safety feature. If you are unable to facturer’s instructions have been ad- cart combination
insert the plug fully into the outlet, hered to. This video product should should be moved
try reversing the plug. If the plug never be placed near or over a radia- with care. Quick
should still fail to fit, contact your tor or heat register.
stops, excessive
electrician to replace your obsolete
force, and uneven
outlet. Do not defeat the safety pur- Attachments: Do not use attachments surfaces
may
not recommended by the video
pose of the polarized plug.
cause the appliance and cart combiproduct manufacturer as they may
nation to overturn.
cause hazards.
ii
Antennas
Outdoor Antenna Grounding: If an
outside antenna or cable system is
connected to the video product, be
sure the antenna or cable system is
grounded so as to provide some protection against voltage surges and
built-up static charges. Section 810
of the National Electrical Code, ANSI/
NFPA No. 70, provides information
with respect to proper grounding
of the mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of
grounding conductors, location of
antenna discharge unit, connection
to grounding electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS
PER NATIONAL ELECTRICAL CODE
Ground
Clamp
Electric
Service
Equipment
Ground
Clamps
Antenna Lead
in Wire
Antenna
Discharge
Unit (NEC
SECTION
810-20)
Grounding
Power Service Grounding Conductors
Electrode System (NEC (NEC SECTION
810-21)
ART 250. PART H)
Power Lines: An outside antenna system should not be located in the
vicinity of overhead power lines or
other electric light or power circuits,
For Your Safety
or where it can fall into such power
lines or circuits. When installing an
outside antenna system, extreme
care should be taken to keep from
touching such power lines or circuits
as contact with them might be fatal.
Use
Cleaning: Unplug this video product
from the wall outlet before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth
for cleaning.
Object and Liquid Entry: Never push
objects of any kind into this video
product through openings as they
may touch dangerous voltage points
or short out parts that could result in a
fire or electric shock. Never spill liquid
of any kind on the video product.
Lightning: For added protection for
this video product receiver during
a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna
or cable system. This will prevent
damage to the video product due to
lightning and power-line surges.
and refer servicing to qualified service personnel under the following
conditions:
• When the power-supply cord or
plug is damaged.
• If liquid has been spilled, or objects
have fallen into the video product.
• If the video product has been exposed to rain or water.
• If the video product has been
dropped or the cabinet has been
damaged.
If the video product does not operate normally follow the operating
instructions.
Adjust only those
controls that are covered by the operating instructions as an improper
adjustment of other controls may result in damage and will often require
extensive work by a qualified technician to restore the video product to
its normal operation.
Be sure to read these notes before use
Safety Notes
• Make sure that you use your camera correctly. Read these safety notes and
your Owner’s Manual carefully before use.
• After reading these safety notes, store them in a safe place.
About the Icons
The icons shown below are used in this document to indicate the severity of
the injury or damage that can result if the information indicated by the icon
is ignored and the product is used incorrectly as a result.
WARNING
CAUTION
This icon indicates that personal injury or material damage can result if the
information is ignored.
The icons shown below are used to indicate the nature of the instructions
which are to be observed.
Triangular icons tell you that this information requires attention (“Important”).
When the video product exhibits a
distinct change in performance—
this indicates a need for service.
Replacement Parts: When replacement
parts are required, be sure the service
technician has used replacement
parts specified by the manufacturer
or have the same characteristics as
Service
the original part. Unauthorized subServicing: Do not attempt to service
stitutions may result in fire, electric
this video product yourself as openshock or other hazards.
ing or removing covers may expose
you to dangerous voltage or other Safety Check: Upon completion of any
hazards. Refer all servicing to quali- service or repairs to this video prodfied service personnel.
uct, ask the service technician to
perform safety checks to determine
Damage Requiring Service: Unplug this
that the video product is in proper
video product from the wall outlet
operating condition.
This icon indicates that death or serious injury can result if the information
is ignored.
Circular icons with a diagonal bar tell you that the action indicated is prohibited (“Prohibited”).
Filled circles with an exclamation mark indicate an action that must be performed (“Required”).
WARNING
Unplug from
power socket
If a problem arises, turn the camera off, remove the battery, and disconnect and unplug the
AC power adapter. Continued use of the camera when it is emitting smoke, is
emitting any unusual odor, or is in any other abnormal state can cause a fire
or electric shock. Contact your FUJIFILM dealer.
Do not allow water or foreign objects to enter the camera. If water or foreign objects
get inside the camera, turn the camera off, remove the battery, and disconnect and unplug the AC power adapter. Continued use of the camera can
cause a fire or electric shock. Contact your FUJIFILM dealer.
iii
For Your Safety
WARNING
Do not use in
the bathroom
or shower
Do not
disassemble
Do not use the camera in the bathroom or shower. This can cause a fire or electric
shock.
Never attempt to change or take apart the camera. (Never open the casing.) Do not use the
camera when it has been dropped or the casing is damaged. This can cause a fire or
electric shock. Contact your FUJIFILM dealer.
Do not change, heat or unduly twist or pull the connection cord and do not place heavy objects on the connection cord. These actions could damage the cord and cause a
fire or electric shock. If the cord is damaged, contact your FUJIFILM dealer.
Do not place the camera on an unstable surface. This can cause the camera to fall or
tip over and cause injury.
Never attempt to take pictures while in motion. Do not use the camera while you
are walking or driving a vehicle. This can result in you falling down or being
involved in a traffic accident.
Do not touch any metal parts of the camera during a thunderstorm. This can cause an
electric shock due to induced current from the lightning discharge.
Do not use the battery except as specified. Load the battery as shown by the indicator.
Do not heat, change or take apart the battery. Do not drop or subject the battery to impacts. Do not store the battery with metallic products. Any of these actions can cause
the battery to burst or leak and cause fire or injury as a result.
Use only the battery or AC power adapters specified for use with this camera. Do not use
voltages other than the power supply voltage shown. The use of other power sources
can cause a fire.
If the battery leaks and fluid gets in contact with your eyes, skin or clothing, flush the affected
area with clean water and seek medical attention or call an emergency number right away.
Do not use the AC power adapter to charge batteries other than those specified here. The
supplied AC power adapter is for use only with the type of battery supplied
with the camera. Using the adapter to charge conventional batteries or other
types of rechargeable batteries can cause the battery to leak fluid, overheat
or burst.
When carrying the battery, install it in a digital camera or keep it in the hard case. When
storing the battery, keep it in the hard case. When discarding, cover the battery terminals
with insulation tape. Contact with other metallic objects or batteries could
cause the battery to ignite or burst.
iv
WARNING
Keep memory cards out of the reach of small children. Because memory cards are
small, they can be swallowed by children. Be sure to store memory cards out
of the reach of small children. If a child swallows a memory card, seek medical
attention or call an emergency number.
CAUTION
Do not use this camera in locations affected by oil fumes, steam, humidity or dust. This
can cause a fire or electric shock.
Do not leave this camera in places subject to extremely high temperatures. Do not leave
the camera in locations such as a sealed vehicle or in direct sunlight. This
can cause a fire.
Keep out of the reach of small children. This product could cause injury in the
hands of a child.
Do not place heavy objects on the camera. This can cause the heavy object to tip
over or fall and cause injury.
Do not move the camera while the AC power adapter is still connected. Do not pull on the
connection cord to disconnect the AC power adapter. This can damage the power
cord or cables and cause a fire or electric shock.
Do not cover or wrap the camera or the AC power adapter in a cloth or blanket. This can
cause heat to build up and distort the casing or cause a fire.
When you are cleaning the camera or you do not plan to use the camera for an extended
period, remove the battery and disconnect and unplug the AC power adapter. Failure to
do so can cause a fire or electric shock.
When charging ends, unplug the AC power adapter from the power socket. Leaving the
adapter plugged into the power socket can cause a fire.
Using a flash too close to a person’s eyes may temporarily affect the eyesight. Take particular care when photographing infants and young children.
When a memory card is removed, the card could come out of the slot too quickly. Use your
finger to hold it and gently release the card.
Request regular internal testing and cleaning for your camera. Build-up of dust in your
camera can cause a fire or electric shock. Contact your FUJIFILM dealer to
request internal cleaning every two years. Please note that this service is not
free of charge.
For Your Safety
The Battery and Power Supply
The following describes the proper
use of the battery and how to
prolong its life. Incorrect use can
shorten battery life or cause leakage,
overheating, fire, or explosion.
The battery is not charged at shipment. Charge the battery before
use. Keep the battery in its case
when not in use.
Notes on the Battery
The battery gradually loses its charge
when not in use. Charge the battery
one or two days before use.
Battery life can be extended by turning the camera off when not in use.
Battery capacity decreases at low temperatures; a depleted battery may not
function at when cold. Keep a fully
charged spare battery in a warm place
and exchange as necessary, or keep
the battery in your pocket or other
warm place and insert it in the camera
only when shooting. Do not place the
battery in direct contact with hand
warmers or other heating devices.
Charging the Battery
Charge the battery using the supplied
AC power adapter (pg. 6). Charging
times will increase at ambient temperatures below +10 °C (+50 °F) or
above +35 °C (+95 °F). Do not attempt
to charge the battery at temperatures
above 40 °C (+104 °F); at temperatures
below 0 °C (+32 °F), the battery will not
charge.
Do not attempt to recharge a fully • Do not expose to water.
charged battery. The battery does • Keep the terminals clean.
not however need to be fully dis- • The battery and camera body may
become warm to the touch after
charged before charging.
extended use. This is normal.
The battery may be warm to the
touch immediately after charging or AC power adapters
Use only FUJIFILM AC power adaptuse. This is normal.
ers designated for use with this camBattery Life
era. Other adapters could damage
At normal temperatures, the battery
the camera.
can be recharged about 300 times.
• The AC power adapter is for indoor
A noticeable decrease in the length
use only.
of time the battery will hold a charge
• Be sure the DC plug is securely
indicates that it has reached the end
connected to the camera.
of its service life and should be re• Turn the camera off before disconplaced.
necting the adapter. Disconnect the
adapter by the plug, not the cable.
Storage
Performance may be impaired if the • Do not use with other devices.
battery is left unused for extended • Do not disassemble.
periods when fully charged. Run the • Do not expose to high heat and
humidity.
battery flat before storing it.
• Do not subject to strong physical
If the camera will not be used for an
shocks.
extended period, remove the bat• The AC power adapter may hum or
tery and store it in a dry place with
become hot to the touch during
an ambient temperature of from
use. This is normal.
+15 °C to +25 °C (+59 °F to +77 °F). Do
• If the AC power adapter causes
not store in locations exposed to exradio interference, reorient or relotremes of temperature.
cate the receiving antenna.
Cautions: Handling the Battery
Using the Camera
• Do not transport or store with
metal objects such as necklaces or To ensure that images are recorded
correctly, do not subject the camera
hairpins.
to impact or physical shocks while
• Do not expose to flame or heat.
images are being recorded.
• Do not disassemble or modify.
• Charge with designated devices Electrical Interference
only.
This camera may interfere with hos• Dispose of used batteries promptly. pital or aviation equipment. Consult
• Do not drop or subject to strong with hospital or airline staff before
physical shocks.
using the camera in a hospital or on
an aircraft.
Liquid Crystal
In the event that the monitor is damaged, care should be taken to avoid
contact with liquid crystal. Take the
urgent action indicated should any
of the following situations arise:
• If liquid crystal comes in contact with
your skin, clean the area with a cloth
and then wash thoroughly with
soap and running water.
• If liquid crystal enters your eyes, flush
the affected eye with clean water
for at least 15 minutes and then
seek medical assistance.
• If liquid crystal is swallowed, rinse
your mouth thoroughly with water.
Drink large quantities of water and
induce vomiting, then seek medical assistance.
Take Test Shots
Before taking photographs on important occasions (such as at weddings
or before taking the camera on a trip),
take a test shot and view the result in
the monitor to ensure that the camera is functioning normally. FUJIFILM
Corporation can not accept liability
for damages or lost profits incurred
as a result of product malfunction.
v
For Your Safety
NOTICES
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
For Customers in Canada
Please read the “Safety Notes” (pages iii–v) and make sure you understand CAUTION: This Class B digital apparatus complies with Canadian ICES-003.
them before using the camera.
EC Declaration of Conformity
Perchlorate Material—special handling may apply. See http://www.dtsc. We
Name:
FUJIFILM Electronic Imaging Europe GmbH
ca.gov/hazardouswaste/perchlorate.
Address:
Benzstrasse 2
For Customers in the U.S.A.
47533 Kleve, Germany
Tested To Comply With FCC Standards
declare that the product
FOR HOME OR OFFICE USE
Product Name:
FUJIFILM DIGITAL CAMERA REAL 3D W1
Manufacturer’s Name: FUJIFILM Corporation
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to Manufacturer’s Address: 7-3, AKASAKA 9-CHOME, MINATO-KU,
TOKYO 107-0052 JAPAN
the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including conforms to the following Standards:
Safety:
EN60065: 2002 + A1: 2006
interference that may cause undesired operation.
EMC:
EN55022: 1998 + A1: 2000 + A2: 2003 Class B
CAUTION
EN55024: 1998 + A1: 2001 + A2: 2003
This equipment has been tested and found to comply with the limits for a
EN61000-3-2: 2006
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
EN61000-3-3: 1995 + A1: 2001 + A2: 2005
designed to provide reasonable protection against harmful interference in
following the provision of the EMC Directive (2004/108/EC)
a residential installation. This equipment generates, uses, and can radiate
and Low Voltage Directive (2006/95/EC).
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment
Kleve, Germany
August 1, 2009
off and on, the user is encouraged to try to correct the interference by one
Place
Date
Signature, Managing Director
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly approved
in this manual could void the user’s authority to operate the equipment.
Notes on the Grant
To comply with Part 15 of the FCC Rules, this product must be used with a
FUJIFILM-specified ferrite-core A/V cable, USB cable, and DC supply cord.
vi
For Your Safety
Notes on Copyright
Unless intended solely for personal use, images recorded using your digital
camera system cannot be used in ways that infringe copyright laws without the consent of the owner. Note that some restrictions apply to the
photographing of stage performances, entertainments, and exhibits, even
when intended purely for personal use. Users are also asked to note that
the transfer of memory cards containing images or data protected under
Instead it should be taken to an applicable collection point
copyright laws is only permissible within the restrictions imposed by those
for the recycling of electrical and electronic equipment.
copyright laws.
By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences to the en- Trademark Information
vironment and human health, which could otherwise be xD-Picture Card is a trademark of FUJIFILM Corporation. Macintosh, QuickTime, and Mac OS are trademarks of Apple Inc. in the U.S.A. and other
caused by inappropriate waste handling of this product.
countries. Microsoft, Windows, the Windows logo, Windows Vista and the
This symbol on the batteries or accumulators indicates that Windows Vista logo are trademarks or registered trademarks of Microsoft
those batteries shall not be treated as household waste.
Corporation in the United States and/or other countries. “Windows” is an
If your equipment contains easy removable batteries or ac- abbreviation used in reference to the Microsoft Windows operating system.
cumulators please dispose these separately according to Adobe and Adobe Reader are either trademarks or registered trademarks
of Adobe Systems Incorporated in the U.S.A. and/or other countries. The
your local requirements.
IrSimple, IrSS, and IrSimpleShot trademarks are owned by the Infrared Data
The recycling of materials will help to conserve natural resources. For more Association®. The SDHC logo is a trademark.
detailed information about recycling this product, please contact your local
city office, your household waste disposal service or the shop where you Note: The “Designed for Microsoft® Windows® XP” and “CERTIFIED FOR Windows
Vista™” logos apply only to the camera and camera hardware driver.
purchased the product.
Disposal of Electrical and Electronic Equipment in Private Households
Disposal of Used Electrical and Electronic Equipment (Applicable in the European
Union, Norway, Iceland and Liechtenstein)
This symbol on the product, or in the manual and in the
warranty, and/or on its packaging indicates that this product shall not be treated as household waste.
In Countries Outside the European Union, Norway, Iceland and Liechtenstein
If you wish to discard this product, including the batteries or accumulators, please contact your local authorities and ask for the correct way of
disposal.
vii
About This Manual
Before using the camera, read this manual and the warnings on pages ii–vii. For information on specific
topics, consult the sources below.
✔ Camera Q & A ....................................................pg.
.................................................... pg. ix
Know what you want to do but don’t know the
name for it? Find the answer in “Camera Q & A.”
✔ Table of Contents .............................................
.............................................pg.
pg. xii
The “Table of Contents” gives an overview of the
entire manual. The principal camera operations
are listed here.
✔ Troubleshooting ..............................................
..............................................pg.
pg. 91
Having a specific problem with the camera?
Find the answer here.
✔ Warning Messages and Displays .......................
.......................pg.
pg. 98
Find out what’s behind that flashing icon or error
message in the monitor.
✔ Glossary ........................................................
........................................................pg.
pg. 102
The meanings of some technical terms may be
found here.
Memory Cards
Pictures can be stored in the camera’s internal memory or on optional SD and SDHC memory cards. In this
manual, SD memory cards are referred to as “memory cards.” For more information, see page 9.
viii
Camera Q & A
Find items by task.
Camera Setup
Question
How do I set the camera clock?
Can I set the clock to local time when I travel?
How do I keep the display from turning off automatically?
How do I make the display brighter or darker?
How do I stop the camera beeping and clicking?
Can I change the sound the shutter makes?
What are the parts of the camera called?
What do the icons in the display mean?
How do I use the menus?
What’s behind that flashing icon or error message?
How much charge is left in the battery?
Key phrase
See page
Date and time
11
Time difference
86
Auto power off
85
LCD brightness
84
Operation and shutter volume
80
Silent mode
16
Shutter sound
80
Parts of the camera
2
Displays
3
Menus
57
Messages and displays
98
Battery level
14
Sharing Pictures
Question
Can I print pictures on my home printer?
Can I copy my pictures to my computer?
Can I copy pictures to a hand-held device?
Key phrase
See page
Printing pictures *
45
Viewing pictures on a computer
50
Infrared (IR)
54
* For information on printing C pictures, visit http://fujifilm.com/3d/print/.
ix
Camera Q & A
Taking Pictures
Question
How do I take C photographs?
How do I take D photographs?
How do I shoot movies in C or D?
How many pictures can I take?
How can I make good portraits?
Can I choose my own settings for different scenes?
How do I shoot close-ups?
How do I keep the flash from firing?
How do I stop my subjects’ eyes glowing red when I use the flash?
How do I “fill-in” shadows on back-lit subjects?
How do I take a series of pictures in a single burst?
How do I take a group portrait that includes the photographer?
How do I frame pictures with the subject off to one side?
Can I choose shutter speed or aperture?
x
Key phrase
Taking C photographs
Taking D photographs
Recording movies
Memory capacity
Intelligent Face Detection
Scene position
Close-ups (macro mode)
See page
13
19
41
104
64
27
22
Flash mode
23
Continuous mode
Self-timer mode
Focus lock
65
25
20
29, 30,
31
P, A, and M modes
Camera Q & A
Viewing Pictures
Question
How do I switch between C and D views?
How do I view C pictures?
How do I view D pictures?
How do I view my pictures?
How do I delete the current picture?
Can I select other pictures for deletion?
Can I zoom in on pictures during playback?
How do I view a lot of pictures at once?
How do I view all pictures taken on the same day?
Can I protect my pictures from accidental deletion?
Can I hide the icons in the display when viewing my pictures?
Can I view my pictures in a slide show?
Can I crop unwanted elements out of my pictures?
Can I make small copies of pictures?
Can I copy pictures from internal memory to a memory card?
How do I view my pictures on TV?
Key phrase
See page
36
Switching between C and D
18
Viewing C pictures
19
Viewing D pictures
Single-frame playback
36
18
The b button
Deleting pictures
39
Playback zoom
37
Multi-frame playback
38
Sort by date
38
Protect
73
Choosing a display format
36
Slide show
69
Crop (trimming)
76
Resize
77
Copy
74
Viewing pictures on TV
44
xi
Table of Contents
For Your Safety ................................................................................. ii
IMPORTANT SAFETY INSTRUCTIONS ...................................... ii
Safety Notes .................................................................................... iii
NOTICES ............................................................................................ vi
About This Manual .......................................................................viii
Camera Q & A .................................................................................... ix
Before You Begi
Begin
n
Introduction....................................................................................... 1
Symbols and Conventions .......................................................... 1
Supplied Accessories .................................................................... 1
Parts of the Camera ....................................................................... 2
Camera Displays .......................................................................... 3
First Steps
Steps
Inserting the Battery...................................................................... 4
Charging the Battery ..................................................................... 6
Inserting a Memory Card ............................................................. 7
Turning the Camera on and Off...............................................10
Shooting Mode .............................................................................10
Playback Mode ..............................................................................10
Basic Setup ....................................................................................... 11
Basic Photography and Playbac
Playback
k
Taking C Pictures in Auto Mode .........................................13
Viewing C Pictures ....................................................................18
Shooting and Viewing D Pictures ......................................19
Taking Pictures in D.................................................................19
Viewing Pictures in D..............................................................19
xii
More on Photography
Photography
Focus Lock (CD) ......................................................................20
F Macro Mode (Close-ups) (D) ...........................................22
N Using the Flash (Super Intelligent Flash) (CD) .....23
h Using the Self-Timer (CD) .............................................25
Shooting Mode (CD).............................................................27
B AUTO ..........................................................................................27
SP SCENE POSITION ....................................................................27
M MANUAL .....................................................................................29
A APERTURE PRIORITY AE .........................................................30
P PROGRAM AE .............................................................................31
B TWIN CAMERA................................................................31
V TELE/WIDE ............................................................................32
X 2-COLOR.................................................................................32
W 2-SENSITIVITY .......................................................................32
A ADVANCED 3D ................................................................33
A INDIVID. SHUTTER 3D .......................................................34
B INTERVAL 3D SHOOTING .................................................35
More on Playback
Playback
Playback Options...........................................................................36
Playback Zoom..............................................................................37
s Multi-Frame Playback..........................................................38
Sort by Date....................................................................................38
A Deleting Pictures ....................................................................39
Table of Contents
Moviess
Movie
F Recording Movies ...................................................................41
a Viewing Movies .......................................................................43
Connectionss
Connection
Viewing Pictures on TV ...............................................................44
Printing Pictures via USB (D Only) .....................................45
Connecting the Camera ............................................................45
Printing Selected Pictures ........................................................46
Printing the DPOF Print Order ................................................47
Creating a DPOF Print Order ....................................................48
Viewing Pictures on a Computer............................................50
Installing FinePixViewer ............................................................50
Connecting the Camera ............................................................52
IR Communication ........................................................................54
Sending Pictures to Other Devices ....................................55
Receiving Pictures from Other Devices ............................56
Menuss
Menu
Using the Menus: Shooting Mode .........................................57
Using the F-Mode Menu..........................................................57
F-Mode Menu Options.............................................................58
N ISO ............................................................................................59
O IMAGE SIZE ............................................................................59
T IMAGE QUALITY ..................................................................60
D WHITE BALANCE .................................................................60
P G COLOR...............................................................61
Using the Shooting Menu.........................................................62
Shooting Menu Options ............................................................63
b FACE DETECTION (D Only) ..........................................64
R CONTINUOUS.......................................................................65
C PHOTOMETRY ......................................................................66
F 2D AF MODE (D Only) ...................................................66
S POWER MANAGEMENT ....................................................67
Using the Menus: Playback Mode ..........................................68
Using the F-Mode Menu..........................................................68
F-Mode Menu Options.............................................................69
I SLIDE SHOW .........................................................................69
Using the Playback Menu .........................................................70
Playback Menu Options.............................................................70
i PARALLAX CONTROL (C Only)...................................71
B RED EYE REMOVAL (D Only) .......................................71
C IMAGE ROTATE (D Only) ...............................................72
D PROTECT ................................................................................73
E COPY........................................................................................74
G CROP........................................................................................76
O RESIZE .....................................................................................77
The Setup Menu .............................................................................78
Using the Setup Menu ...............................................................78
Setup Menu Options...................................................................80
A IMAGE DISP. ..........................................................................82
B FRAME NO. ............................................................................83
D DIGITAL ZOOM (D Only) ...............................................84
o 3DREC .....................................................................................84
I PLAYBACK VOLUME ...........................................................84
J LCD BRIGHTNESS ................................................................84
K FORMAT..................................................................................85
M AUTO POWER OFF ..............................................................85
xiii
Table of Contents
N TIME DIFFERENCE ...............................................................86
r 3D CAUTION DISP ..............................................................87
q OPT AXIS CONTROL ...........................................................87
Troubleshooting
Troubleshootin
g
Troubleshooting ............................................................................91
Warning Messages and Displays ............................................98
Technical Notes
Notes
Appendix
Appendi
x
Optional Accessories ...................................................................88
Accessories from FUJIFILM .......................................................89
Caring for the Camera .................................................................90
Glossary .......................................................................................... 102
Internal Memory/Memory Card Capacity ....................... 104
Specifications ............................................................................... 105
FUJIFILM Digital Camera Worldwide Network ............. 109
3 Caution: Using the FinePix REAL 3D W1
D display is recommended for young children (up to the age of about six) whose visual system is still maturing
and for individuals with notable differences in vision between their two eyes, who may find it difficult or impossible to observe the C effect. Should you experience fatigue or discomfort while viewing C images, cease use
immediately. A ten-minute break is recommended about once every half hour. Switch to D immediately if C
images still appear double after you have adjusted parallax. Individuals with a history of photosensitive epilepsy
or heart disease or who are unwell or suffering from fatigue, insomnia, or the affects of alcohol should refrain from
viewing C images. Viewing C images while in motion may cause fatigue or discomfort.
File Formats
C pictures are recorded in one of two new formats: multi-picture format for photographs (pg. 18, 102) and 3D
movie file format for movies (pg. 41, 102). D images are recorded in existing formats.
xiv
Introduction
Symbols and Conventions
Menus and other text in the camera monitor are shown in bold. In the illustrations in this manual, the
monitor display may be simplified for explanatory purposes.
Before You Begin
The following symbols are used in this manual:
3 Caution: This information should be read before use to ensure correct operation.
1Note: Points to note when using the camera.
2 Tip: Additional information that may be helpful when using the camera.
Supplied Accessories
The following items are included with the camera:
NP-95 rechargeable
battery
AC-5VC AC power
adapter
Owner’s Manual
(this manual)
Software for FinePix CD
Attaching the Strap
Attach the strap as shown.
USB cable
Strap
3 Caution
To ensure that you do not
drop the camera, wear the
strap on your wrist.
1
Introduction
Parts of the Camera
For more information, refer to the page listed to the right of each item.
Selector button
Move cursor up
m (monitor brightness) button (see below)
b (delete) button (pg. 18)
Move cursor left
F (macro) button
(pg. 22)
Move cursor right
N (flash) button
(pg. 23)
Move cursor down
h (self-timer) button (pg. 25)
1
2
3
4
5
6
7
8
9
Shutter button ...........................................17
Zoom control....................... 14, 37, 38, 42
Flash..................................................................23
Infrared port ................................................54
Left lens
Right lens
Microphone .................................................41
On/off switch and lens cover ...........10
Illuminator ....................................................80
Self-timer lamp ..........................................26
10 3D button.......................................................13
11
12
13
14
15
16
17
18
19
20
2D button.......................................................19
Q (parallax) button .............................13
F/B button .............................................41
MODE button ................................................13
Monitor ............................................................. 3
Indicator lamp .......................................6, 17
MENU/OK button ......................................... 11
a (playback) button ....................18, 36
Strap eyelet .................................................... 1
Terminal cover............................44, 45, 52
21
22
23
24
25
26
27
28
29
30
F (photo mode) button.....................57
Speaker ...........................................................43
DISP (display)/BACK button .......... 15, 36
Battery-chamber cover .......................... 4
Tripod mount
USB and A/V connector .......44, 45, 52
Connector for AC power adapter .... 6
Battery chamber ......................................... 4
Battery latch .................................................. 4
Memory card slot ....................................... 8
2 Tip: Monitor Brightness
Pressing the m button briefly increases monitor brightness, making the display easier to see in bright light. Normal brightness is restored when a photograph is taken.
2
Introduction
Camera Displays
The following indicators may appear during shooting and playback:
M
3D
4:3 N 9
ISO 800
02
*
12 / 31 / 2050 10 : 00 AM
-1 2 3
50
F5
1
2
3
4
5
6
7
8
* a: indicates that no memory card 9
is inserted and that pictures will 10
be stored in the camera’s internal 11
12
memory (pg. 7).
Image quality..............................................60
Image size .....................................................59
Sensitivity ......................................................59
Continuous shooting mode .............65
Macro (close-up) mode........................22
Flash mode...................................................23
Silent mode .................................................16
Intelligent Face Detection
indicator ........................................................ 64
Shooting mode .........................................57
C/D mode indicator .....................13
Battery level .................................................14
Quick AF ................................................. 12, 67
13
14
15
16
17
18
19
20
21
22
23
24
25
Self-timer indicator .................................25
Metering ........................................................66
White balance ............................................60
Date and time......................................11, 80
Number of available frames...........104
G color .......................................61
Bright monitor indicator........................ 2
Focus warning ...................................16, 98
Blur warning ........................................23, 98
Parallax display...........................................13
Internal memory indicator * ................. 7
Focus frame .........................................16, 20
Exposure compensation .....................58
Before You Begin
■ Shooting
■ Playback
3D
100-0001
4:3 N
ISO 800
02
Gift image .............................................36, 56 6 C image .....................................................18
DPOF print indicator ..............................47 7 Playback mode indicator ....................36
Red-eye removal indicator ................71 8 C/D mode indicator .....................36
Intelligent Face Detection
9 Protected image .......................................73
indicator ........................................................ 64 10 Frame number ...........................................83
5 Silent mode indicator............................16 11 Parallax display...........................................13
1
2
3
4
12 / 31 / 2050 10 : 00 AM
-1 2 3
50
F5
Note: The indicators actually displayed during shooting and playback vary with camera settings.
3
Inserting the Battery
Insert the battery in the camera as described below.
1 Open the battery-chamber cover.
First Steps
1 Note
Be sure the camera is off before opening the battery-chamber cover.
3 Cautions
• Do not open the battery-chamber cover when
the camera is on. Failure to observe this precaution could result in damage to image files or
memory cards.
• Do not use excessive force when handling the
battery-chamber cover.
4
Insert the battery.
2 Insert
the battery
with
the terminals first and the
arrow aligned with the arrow next to the battery
chamber. Slide the battery into the camera, keeping the battery
latch pressed to one side as shown below.
Confirm that the battery is securely latched.
Arrow
Battery latch
3 Caution
Insert the battery in the correct orientation. Do
NOT use force or attempt to insert the battery upside down or backwards. The battery will slide in
easily in the correct orientation; the camera will
not turn on if the battery is inserted incorrectly.
Inserting the Batteries
3 Close the battery-chamber cover.
Removing the Battery
After turning the camera off, open the battery-chamber cover, press the battery latch to the side, and slide
the battery out of the camera as shown.
First Steps
Battery latch
3 Caution
Turn the camera off before removing the battery.
3 Cautions
• Do not affix stickers or other objects to the battery. Failure to observe this precaution could make it impossible
to remove the battery from the camera.
• Do not short the battery terminals. The battery could overheat.
• Read the cautions on page v.
• Use only batteries designated for use with this camera. Failure to observe this precaution could result in product
malfunction.
• Do not remove the labels from the battery or attempt to split or peel the outer casing.
• The battery gradually loses its charge when not in use. Charge the battery one or two days before use.
5
Charging the Battery
The battery is not charged at shipment. Charge the battery before use.
Connect the AC power adapter.
1 Connect
the supplied AC power adapter to
the camera as shown.
Plug the adapter in.
2 Plug
the AC power adapter into a power outlet. The indicator lamp will glow red while
the battery charges (if the indicator lamp
does not light, check that the battery is correctly inserted). Charging is complete when
the lamp turns off.
Indicator lamp
2 Tips: Using an AC power adapter
• The AC power adapter can also be used to power the
camera. Use to prevent unexpected loss of power
during extended playback or when the camera is
connected to a computer or TV.
• If the camera is powered by an AC power adapter,
demo mode slides will be displayed when the camera is turned on. Demo mode can be disabled using
the s DEMO MODE option in the setup menu (pg.
81).
6
The Indicator Lamp
The indicator lamp shows battery charge status as
follows:
Indicator lamp
Battery status
On (red)
Battery charging
Off
Battery fully charged
Blinks (red)
Battery fault
The indicator lamp also shows focus, flash, exposure,
and recording status (pg. 17).
Inserting a Memory Card
Although the camera can store pictures in internal memory, optional SD memory cards (sold separately) can be used to store additional pictures.
First Steps
When no memory card is inserted, a appears in the monitor and internal memory is used for recording
and playback. Note that because camera malfunction could cause internal memory to become corrupted, the pictures in internal memory should periodically be transferred to a computer and saved on
the computer hard disk or on removable media such as CDs or DVDs. The pictures in internal memory
can also be copied to a memory card (see page 74). To prevent internal memory from becoming full,
be sure to delete pictures when they are no longer needed.
When a memory card is inserted as described below, the card will be used for recording and playback.
■ Compatible Memory Cards
SanDisk SD and SDHC memory cards have been approved for use in the camera. A complete list
of approved memory cards is available at http://www.fujifilm.com/products/digital_cameras/index.html.
Operation is not guaranteed with other cards. The camera can not be used with xD-Picture Cards or
MultiMediaCard (MMC) devices.
3 Caution
SD memory cards can be locked, making it impossible to format the card or to record or
delete images. Before inserting an SD memory card, slide the write-protect switch to the
unlocked position.
Write-protect switch
7
Inserting a Memory Card
■ Inserting a Memory Card
Open the battery-chamber cover.
1
3 Close the battery-chamber cover.
1 Note
Be sure the camera is off
before opening the batterychamber cover.
Insert the memory card.
2 Holding
the memory card in the orientation
shown below, slide it in until it clicks into
place.
Be sure card is in correct orientation; do not insert at an
angle or use force.
8
Removing Memory Cards
After confirming that the camera
is off, press the card in and then
release it slowly. The card can
now be removed by hand.
3 Cautions
• The memory card may spring out if you remove
your finger immediately after pushing the card in.
• Memory cards may be warm to the touch after being removed from the camera. This is normal and
does not indicate a malfunction.
Inserting a Memory Card
First Steps
3 Cautions
• Do not turn the camera off or remove the memory card while the memory card is being formatted or data are being recorded to or
deleted from the card. Failure to observe this precaution could damage the card.
• Format memory cards before first use or after using them in a computer or other device. For more information
on formatting memory cards, see page 85.
• Memory cards are small and can be swallowed; keep out of reach of children. If a child swallows a memory card,
seek medical assistance immediately.
• miniSD or microSD adapters that are larger or smaller than the standard dimensions of an SD card may not eject
normally; if the card does not eject, take the camera to an authorized service representative. Do not forcibly
remove the card.
• Do not affix labels to memory cards. Peeling labels can cause camera malfunction.
• Movie recording may be interrupted with some types of SD memory card. Use a card with a class 4 write speed
(4 MB/s) or better when shooting movies.
• The data in internal memory may be erased or corrupted when the camera is repaired. Please note that the
repairer will be able to view pictures in internal memory.
• Formatting a memory card or internal memory in the camera creates a folder in which pictures are stored. Do
not rename or delete this folder or use a computer or other device to edit, delete, or rename image files. Always
use the camera to delete pictures from memory cards and internal memory; before editing or renaming files,
copy them to a computer and edit or rename the copies, not the originals.
9
Turning the Camera on and Off
Shooting Mode
Playback Mode
To turn the camera on, open the lens cover as
shown below. The camera turns off when the
lens cover is closed.
To turn the camera on and begin playback without opening the lens cover, press the a button
for about a second.
Camera on
Camera off
2 Tip: Switching to Playback Mode
Press the a button for about a second to start playback. Press the shutter button halfway to return to
shooting mode.
3 Caution
Pictures can be affected by fingerprints and other
marks on the lenses. Keep the lenses clean.
To turn the camera off, open and close the lens
cover.
2 Tip: Switching to Shooting Mode
To exit to shooting mode, press the shutter button
halfway. Press the a button to return to playback.
2 Tip: Auto Power Off
The camera will turn off automatically if no operations are performed for the length of time selected in the
M AUTO POWER OFF menu (pg. 85; note that OFF is not available when p QUICK AF is selected for
S POWER MANAGEMENT). To turn the camera on, close and reopen the lens cover or press the a button for
about a second.
10
Basic Setup
A language-selection dialog is displayed the first time the camera is turned on. Set up the camera as
described below (for information on resetting the clock or changing languages, see page 80).
1 Choose a language.
2 Set the date and time.
START MENU
DATE / TIME NOT SET
2009
2008
2007
SET
NO
1.1 Press the selector up, down,
left, or right to highlight a language.
1.2 Press MENU/OK.
SET
1. 1 12 : 00
AM
NO
First Steps
2011
2010
YY. MM. DD
2.1 Press the selector left or right to
highlight the year, month, day,
hour, or minute and press up
or down to change. To change
the order in which the year,
month, and day are displayed, highlight
the date format and press the selector up
or down.
2.2 Press MENU/OK.
11
Basic Setup
3 Choose power management options.
POWER MANAGEMENT
POWER SAVE
QUICK AF
Power saving for longer
battery life
SET
NO
3.1 Press the selector up or down
to highlight one of the following options:
• n POWER SAVE: Save battery
power.
• p QUICK AF: Reduce focusing time, ensuring a quick shutter response.
3.2 Press MENU/OK.
12
2 Tip: The Camera Clock
If the battery is removed for an extended period, the
camera clock will be reset and the language-selection
dialog will be displayed when the camera is turned
on. If the battery is left in the camera for about two
hours, the battery can be removed for about six hours
without resetting clock, language selection, or power
management options.
Taking C Pictures in Auto Mode
This section describes how to take C pictures in A mode.
Turn the camera on.
1 Fully
open the lens cover.
Select A mode.
2 Press
the MODE button to
Press the selector up or
down to highlight A
and press MENU/OK.
C.
3 Select
Press the 3D button.
C
will be displayed in the
monitor.
AUTO
3D
AUTO
AUTO
Automatic mode
setting according to
shooting conditions.
Note that adjusting parallax reduces horizontal frame coverage. The new crop is shown by
black borders in the display.
02
AUTO
3D
04
2 Tip: Auto Parallax
For automatic parallax adjustment, select ON for
i AUTO PARALLAX CONTROL (pg. 63). Parallax
can still be adjusted manually when ON is selected.
3 Caution: Excessive Parallax
Too much parallax may make it impossible to perceive the 3D effect.
Basic Photography and Playback
display the mode selection menu.
Parallax (pg. 103)
The appearance of C images AUTO
3D
can be adjusted using the Q (R
and S) buttons. The percentage is displayed in the monitor.
Press the shutter button to take
a picture at the current setting,
or press the 3D button to reset parallax.
13
Taking C Pictures in Auto Mode
Check the battery level.
4 Check
the battery level in the display.
AUTO
3D
r
q
w
e
Frame the picture.
5 Position
the main subject in the focus frame
and use the zoom control to frame the picture in the display.
Select W to zoom out
AUTO
Indicator
D
(white)
C
(white)
B
(red)
A
(blinks red)
Description
Battery partially discharged.
Zoom indicator
Battery more than half discharged.
Low battery. Charge as soon as possible.
Battery exhausted. Turn camera off
and charge battery.
1 Note: C
The C effect may not be
visible at high zoom ratios,
in subjects that are outside
the suggested range (pg.
105), poorly lit or at the edge
of the frame, or if the display
is viewed from the side.
2 Tip: Focus Lock
Use focus lock (pg. 20) to focus on subjects that are not in the focus frame.
14
Select T to zoom in
AUTO
Taking C Pictures in Auto Mode
Holding the Camera
Hold the camera steady with
both hands and brace your
elbows against your sides.
Shaking or unsteady hands
can blur your shots.
Indicators displayed
Indicators hidden
AUTO
3D
AUTO
3D
Best framing
Hiding indicators makes it easier to see the C effect.
To use best framing, position the main subject at the
intersection of two lines or align one of the horizontal lines with the horizon. Use focus lock (pg. 20) to
focus on subjects that will not be in the center of the
frame in the final photograph.
Basic Photography and Playback
To avoid interfering with the C effect and to prevent pictures that are out of focus or too dark (underexposed), keep your fingers and other objects well
away from the lenses and flash. Note that the C
effect may not be visible if the display is viewed at
an angle.
Shooting Information
To choose the shooting information and guides displayed, press the DISP/BACK button.
15
Taking C Pictures in Auto Mode
h Silent Mode
In situations in which camera sounds or lights may
be unwelcome, hold the DISP/BACK button down until
h is displayed.
6 Focus.
Press the shutter button halfway to focus on
the main subject in the focus frame.
Press
halfway
AUTO
3D
AUTO
3D
Focus frame
The speaker, flash, illuminator, and self-timer lamp
turn off and flash and volume settings can not be
adjusted (note that the flash will still fire when C
is selected in SP mode). To restore normal operation,
press the DISP/BACK button until the h icon is no longer displayed.
Camera selects small focus
frame and focuses on subject
1 Note
The lenses may make a noise when the camera
focuses. This is normal.
If the camera is able to focus with both lenses, it
will beep twice and the indicator lamp will
glow green.
If the camera is unable to focus, the focus frame
will turn red, s will be displayed, and the
indicator lamp will blink green. Change the
composition or use focus lock (pg. 20).
16
Taking C Pictures in Auto Mode
7 Shoot.
Smoothly press the shutter button
the rest of the way down to take
the picture.
Double
beep
q
Press halfway
Click
w
Press the rest of
the way down
1 Note
If the subject is poorly lit, the flash may fire when the
picture is taken. For information on using the flash
when lighting is poor, see page 23.
Indicator lamp
The indicator lamp shows camera status as follows
(see page 6 for information on the charging display):
Indicator lamp
Camera status
Glows green Focus locked.
Blur, focus, or exposure warning. PicBlinks green
ture can be taken.
Blinks green Recording pictures. Additional picand orange tures can be taken.
Recording pictures. No additional
Glows orange
pictures can be taken at this time.
Flash charging; flash will not fire when
Blinks orange
picture is taken.
Lens or memory error (internal memory or memory card full or not formatBlinks red
ted, format error, or other memory
error).
Basic Photography and Playback
2 Tip: The Shutter Button
The shutter button has two positions. Pressing the
shutter button halfway (q) sets focus and exposure;
to shoot, press the shutter button the rest of the way
down (w).
The Indicator Lamp
2 Tip: Warnings
Detailed warnings appear in the display. See pages
98–101 for more information.
17
Viewing C Pictures
Pictures can be viewed in the monitor. When taking important photographs, take a test shot and
check the results. C pictures are stored in multi-picture (“.mpo”) format; JPEG copies can be recorded
by selecting MPO+JPEG for the o 3DREC option in the setup menu.
the a button.
1 Press
The most recent picture
will be displayed in the
monitor. Pictures taken
in C are indicated by a
g icon.
100-0001
3D
the 3D button.
2 Press
Press the 3D button
to
view C pictures in C
(D pictures will still be
displayed in D).
View additional pictures.
3 Press
the selector right to
view pictures in the order
recorded, left to view pictures in reverse order.
Press the shutter button to exit to shooting
mode.
18
Deleting Pictures
To delete the picture currently displayed
in the monitor, press the selector up (b).
The following dialog will be displayed.
ERASE OK?
OK
CANCEL
SET
To delete the picture, press the selector
left to highlight OK and press MENU/OK.
To exit without deleting the picture, highlight CANCEL and press MENU/OK.
2 Tip: The Playback Menu
Pictures can also be deleted from the playback menu
(pg. 39).
Shooting and Viewing D Pictures
Viewing Pictures in D
To shoot pictures in D, press the 2D
button in shooting mode and take pictures as described on pages 13–17. D
is displayed in the monitor and photographs are
taken using the left lens and saved in JPEG (“.jpg”)
format (Exif 2.2).
To view pictures in D, press the 2D
button in playback mode and view
pictures as described on page 18. Note
that when C pictures are viewed in D, only
the image recorded with the left lens will be displayed.
AUTO
2D
Note that the picture angle of photographs taken
in D differs from that of C images.
100-0001
2D
Images that were originally recorded in D are
indicated by the absence of a g icon.
Basic Photography and Playback
Taking Pictures in D
19
CD
Focus Lock
To compose photographs with off-center subjects:
1 Position the subject in the focus frame.
AUTO
3D
recompose the picture.
More on Photography
2 Focus.
Press the shutter button halfway to set focus
and exposure. Focus and exposure (and in
C mode, parallax; pg. 13) will remain locked
while the shutter button is pressed halfway
(AF/AE lock).
Press
halfway
Repeat steps 1 and 2 as desired to refocus
before taking the picture.
20
Recompose the picture.
3 Keeping
the shutter button pressed halfway,
4 Shoot.
Press the shutter-release button the rest of
the way down to take the picture.
Press the rest of
the way down
Focus Lock
Autofocus
Although the camera boasts a high-precision autofocus system, it may be unable to focus on the subjects listed
below. If the camera is unable to focus using autofocus, use focus lock (pg. 20) to focus on another subject at
the same distance and then recompose the photograph.
• Very shiny subjects such as mir• Fast-moving subjects.
rors or car bodies.
Subjects photographed through a window or other reflective object.
Dark subjects and subjects that absorb rather than reflect light, such as hair or fur.
Insubstantial subjects, such as smoke or flame.
Subjects that show little contrast with the background (for example, subjects in clothing that is the same color
as the background).
• Subjects positioned in front of or behind a high-contrast object that is also in the focus frame (for example, a
subject photographed against a backdrop of highly contrasting elements).
Auto Parallax
Although the camera boasts highly precise parallax control, auto parallax may not produce the desired results
with the subjects listed under “Autofocus” (above) or with subjects outside the recommended range (particularly if the subject is close to the camera), repeating rectangular patterns such as venetian blinds or the windows
in an office building, or straight lines such as poles or wires. Use focus lock (pg. 20) or adjust parallax manually
(pg. 13).
More on Photography
•
•
•
•
21
F Macro Mode (Close-ups)
D
For close-ups, press the selector left (F).
AUTO
2D
F is displayed in macro mode.
When macro mode is in effect, the camera focuses on subjects near the center of the frame. Use the
zoom control to compose pictures (pg. 14).
To exit macro mode, press the selector left (F).
1 Notes
• Use of a tripod is recommended to prevent blur caused by camera shake.
• The flash may fail to light the entire subject at very short ranges. Increase the distance to the subject and try
again.
• Macro mode is not available in twin camera mode (pg. 31). It is not available during C shooting except in
A mode (pg. 33).
22
N Using the Flash (Super Intelligent Flash)
CD
When the flash is used, the camera’s Super Intelligent Flash system instantly analyzes the scene based
on such factors as the brightness of the subject, its position in the frame, and its distance from the
camera. Flash output and sensitivity are adjusted to ensure that the main subject is correctly exposed
while preserving the effects of ambient background lighting, even in dimly-lit indoor scenes. Use the
flash when lighting is poor, for example when shooting at night or indoors under low light.
Choose a flash mode.
1 Press
the selector right (N).
The flash mode changes each time the
selector is pressed; in modes other than A, the current mode is indicated by an icon in the display. Choose from the following options:
N (fill flash)
P (off )
O (slow sync)
M (slow sync with
red-eye reduction)
Description
The flash fires when required. Recommended in most situations.
As above, except that camera minimizes “red-eye” caused when light from the flash
is reflected from the subject’s retinas. Available in C only.
The flash fires whenever a picture is taken. Use for backlit subjects or for natural
coloration when shooting in bright light.
The flash does not fire even when the subject is poorly lit. k will appear in the
monitor at slow shutter speeds to warn that pictures may be blurred. Use of a
tripod is recommended.
Capture both the main subject and the background under low light (note that
brightly lit scenes may be overexposed).
More on Photography
Mode
A (auto)
K (auto with
red-eye reduction)
As for slow sync, except that camera minimizes “red-eye.” Available in C only.
23
N Using the Flash (Super Intelligent Flash)
2 Focus.
Press the shutter button halfway to focus. If the flash will fire, p will be displayed when
the shutter button is pressed halfway. At slow shutter speeds, k will appear in the
display to warn that pictures may be blurred; use of a tripod is recommended.
3 Shoot.
Press the shutter button the rest of the way down to shoot.
3 Caution
The flash may fire several times with each shot. Do not move the camera until shooting is complete.
Red-Eye Removal (D)
When g ON J ON is selected for Intelligent Face Detection (D only; pg. 64), red-eye removal
(J) is available in auto (K), fill flash (L), and slow sync (M) modes. Red-eye removal minimizes
“red-eye” caused when light from the flash is reflected from the subject’s retinas as shown in the
illustration at right.
24
h Using the Self-Timer
CD
The camera offers a ten-second timer that allows photographers to appear in their own photographs,
and a two-second timer that can be used to avoid blur caused by the camera moving when the shutter
button is pressed. The self-timer is available in all shooting modes.
Set the timer.
1 The
current self-timer mode is displayed in the monitor. To choose a different setting, press the
selector down (h). The selection changes each time the selector is pressed.
AUTO
3D
Choose from T (self-timer off ),
S (10 s delay), or R (2 s delay)
More on Photography
2 Focus.
Press the shutter button halfway to focus.
3 Caution
Stand behind the camera when using the shutter button. Standing in front
of the lens can interfere with focus and exposure.
Start the timer.
3 Press
the shutter button the rest of the way down to start the timer.
The display in the monitor shows the number of seconds remaining
until the shutter is released. To stop the timer before the picture is
taken, press DISP/BACK.
9
25
h Using the Self-Timer
The self-timer lamp on the front of the camera will blink
immediately before the picture is taken. If the two-second timer is selected, the self-timer lamp will blink as the
timer counts down.
Intelligent Face Detection (D)
Because it ensures that the faces of portrait subjects will be in focus, Intelligent Face Detection (pg. 64) is recommended when using the self-timer for group portraits or self-portraits. To use the self-timer with Intelligent Face
Detection, turn Intelligent Face Detection on, set the timer as described in Step 1, and then press the shutter
button all the way down to start the timer. The camera will detect faces while the timer is counting down and
adjust focus and exposure immediately before the shutter is released. Be careful not to move until the picture
has been recorded.
1 Note
The self-timer turns off automatically when the picture is taken, a different shooting mode is selected, playback
mode is selected, or the camera is turned off.
26
CD
Shooting Mode
Choose a shooting mode according to the scene or type of subject. To select a
shooting mode, press the MODE button to display the mode selection menu. Press
the selector up or down to highlight the desired mode and press MENU/OK. The
selected mode will be shown at the top left corner of the display. The following
options are available:
AUTO
AUTO
Automatic mode
setting according to
shooting conditions.
SP SCENE POSITION
Choose for crisp, clear snapshots (pg. 13). This
mode is recommended in most situations.
The camera offers a choice of
NATURAL &
NATURAL LIGHT
PORTRAIT
“scenes,” each adapted to parLANDSCAPE
ticular shooting conditions or a Portrait with soft
overall tone and
specific type of subject. Select- beautifulSETskin tones CANCEL
ing SP in the mode selection
menu displays the options listed on the following
page; press the selector up or down to highlight
the desired scene and press MENU/OK.
More on Photography
B AUTO
27
Shooting Mode
Scene
Description
Get good results with backlit subjects and other difficult lighting. The camera takes two shots: one without
C NATURAL & N
the flash and one with.
Capture natural light indoors, under low light, or where the flash can not be used. The flash turns off and
D NATURAL LIGHT
sensitivity is raised to reduce blur.
L PORTRAIT
Choose for soft-toned portraits with natural skin tones.
M LANDSCAPE
Choose for crisp, clear daylight shots of buildings and landscapes.
Choose when photographing moving subjects. p QUICK AF is automatically selected for S POWER
N SPORT
MANAGEMENT and priority is given to faster shutter speeds.
Choose this mode for poorly lit twilight or night scenes. Sensitivity is automatically raised to reduce blur
O NIGHT
caused by camera shake.
H NIGHT (TRIPOD) Choose this mode for slow shutter speeds when shooting at night. Use a tripod to prevent blur.
Q SUNSET
Record the vivid colors in sunrises and sunsets.
R SNOW
Choose for crisp, clear shots that capture the brightness of scenes dominated by shining white snow.
S BEACH
Choose for crisp, clear shots that capture the brightness of sunlit beaches.
F UNDERWATER Choose for vivid blues when taking photographs of subjects in an aquarium.
U PARTY
Capture indoor background lighting under low-light conditions.
Choose E ANTI-BLUR (picture stabilization) mode for fast shutter speeds that reduce blur caused by
E ANTI-BLUR
camera shake or subject movement. Recommended for photographs of children and pets.
28
Shooting Mode
M MANUAL
In this mode, you choose both shutter speed and aperture. If desired, exposure can be altered from
the value suggested by the camera.
the F button to display the
1 Press
F-mode menu.
the selector up or down to
2 Press
highlight d SET SHUTTERSPEED,
APERTURE..
the selector up or down to
4 Press
choose the aperture, left or right to
choose the shutter speed.
MODE MENU
400
ISO
4:3
IMAGE SIZE
N
IMAGE QUALITY
AUTO
WHITE BALANCE
STD
COLOR
SET SHUTTERSPEED,APERTURE.
3
Press MENU/OK. Shutter speed and
aperture will be displayed.
M
3D
6 Take pictures.
The Exposure Indicator
The amount the picture will be
under- or over-exposed at current settings is shown by the exposure indicator.
M
3D
More on Photography
MENU/OK to return to shooting
5 Press
mode.
SET
50
F5
Shutter speed
SET
50
F5
Aperture
29
Shooting Mode
A APERTURE PRIORITY AE
In this mode, you choose the aperture while the camera adjusts shutter speed for optimal exposure.
the F button to display the
1 Press
F-mode menu.
the selector up or down to
2 Press
highlight d SETTING APERTURE.
MODE MENU
ISO
IMAGE SIZE
IMAGE QUALITY
WHITE BALANCE
COLOR
SETTING APERTURE
3
400
4:3
N
AUTO
STD
Press MENU/OK. Exposure compensation and aperture will be displayed.
A
3D
Exposure compensation
SET
F5
0
Aperture
30
the selector up or down to
4 Press
choose exposure compensation, left
or right to choose the aperture.
MENU/OK to return to shooting
5 Press
mode.
pictures. If the correct exposure can not
6 Take
be achieved at the selected aperture, shutter
speed will be displayed in red when the shutter button is pressed halfway. Adjust aperture
until the correct exposure is achieved.
3 Caution
If the subject is outside the metering range of the camera, the shutter speed display will show “---”. Press the
shutter button halfway to measure exposure again.
Shooting Mode
B TWIN CAMERA
In this mode, the camera sets aperture and shutter speed automatically. Exposure can be adjusted using the d EXP. COMPENSATION option in
the F-mode menu.
The camera simultaneously
TELE/WIDE
2-COLOR
2-SENSITIVITY
takes two D pictures—one
with each lens—with differ- Simultaneous 2 shots
with wide-edge angle
angle
ent options selected for each. and free-zooming
SET
CANCEL
Selecting B in the mode
selection menu displays the following options;
press the selector up or down to highlight an option and press MENU/OK.
• V TELE/WIDE: Zoom for the left lens can be adjusted using the zoom control. The right lens is
zoomed all the way out (pg. 32).
• X 2-COLOR: The two pictures use different settings for G color (pg. 32).
• W 2-SENSITIVITY: The camera sets sensitivity separately for each lens (pg. 32).
3 Caution
If the subject is outside the metering range of the camera, the shutter speed and aperture displays will show
“---”. Press the shutter button halfway to measure exposure again.
More on Photography
P PROGRAM AE
3 Caution: B Mode
In B mode, the camera displays the view through the left lens
only. Be careful not to obstruct the
right lens during shooting.
31
Shooting Mode
V TELE/WIDE
Zoom for the left lens can be
adjusted using the zoom control. The right lens is zoomed
all the way out.
X 2-COLOR
Select the desired combination of color options using the
j 2-COLOR SETTING option
in the shooting menu (pg. 63).
The selected combination is
shown by an icon in the display.
32
W 2-SENSITIVITY
If lighting permits, sensitivity is set higher for the
right lens than for the left (the maximum value for
the left lens is ISO 400, that for the right lens ISO
1600; note that the same value may be used for
both lenses if the subject is brightly lit).
Left lens
ISO 400
Sensitivity
Right lens
ISO 1600
ISO 100
ISO 400
ISO 100
ISO 100
2-COLOR SETTING
STANDARD + CHROME
2D
Lighting
Dark
Bright
Higher sensitivities permit faster shutter speeds.
If you pan the camera to follow a moving object,
the background in the shot taken with the right
lens will be less blurred than in the shot taken
with the left, producing different speed effects. If
lighting is poor, the shot taken with the right lens
will be less blurred, while the shot taken with the
left lens will have less noise.
Shooting Mode
A ADVANCED 3D
This mode offers greater C flexibility than A mode. The camera takes two
INTERVAL 3D SHOOTING
INDIVID. SHUTTER 3D
shots with the left lens and combines them to form a C picture. Selecting A
in the mode selection menu displays the options listed below; press the selector up 3D image from
2 consecutive shots
with input interval
or down to highlight an option and press MENU/OK.
SET
CANCEL
• B INTERVAL 3D SHOOTING: The camera automatically takes the two shots at a fixed
interval (pg. 35).
• A INDIVID. SHUTTER 3D: One shot is taken each time you press the shutter button (pg. 34).
More on Photography
33
Shooting Mode
A INDIVID. SHUTTER 3D
Use this option to combine two shots taken from
different angles to create a C picture. Use in
macro mode, to create C pictures of distant object, and in other situations in which the desired
results can not be achieved in A mode.
2 Take the first shot.
1 Note
To exit without taking the second shot, press DISP/
BACK or turn the camera off. Note that the camera
will turn off and shooting will be cancelled if no
operations are performed for the length of time selected for M AUTO POWER OFF (pg. 85).
first shot will be superimposed on the
3 The
view through the lens. Using the first shot as
Choose the order in which the shots will be
1 taken
(left first or right first) using the l TURN
option in the shooting menu (pg. 63).
SHOOTING MENU
3D
SHOOTING MODE
TURN
POWER MANAGEMENT
SET-UP
First shot shown by E
34
a guide, reposition the camera and take the
second shot to create a C picture. Note that
the 3D effect may not be visible if the parallax between the two positions is too great; the
best results will be achieved if the distance the
camera is moved between the two shots is
between 1/30th and 1/50th of the distance to the
subject.
Shooting Mode
B INTERVAL 3D SHOOTING
Use this option to take C pictures of distant objects from a moving vehicle.
the order in which the shots will be
2 Choose
taken (left first or right first) using the l TURN
option in the shooting menu (pg. 63). Choose
the order that matches the direction of motion.
SHOOTING MENU
MIN.
3D
shooting menu (pg. 63). Choose shorter delays for less distant objects or faster-moving
vehicles (the best results will be achieved if the
distance the camera moves between the two
shots is between 1/30th and 1/50th of the distance
to the subject). The 3D effect may not be visible if the parallax between the two shots is
too great or if another object is between the
camera and your subject.
SHOOTING MENU
SHOOTING MODE
3D INTERVAL TIME
TURN
POWER MANAGEMENT
SET-UP
MIN.
MINIMUM
1.0SEC
1.0
1.5SEC
2.0SEC
3.0SEC
5.0SEC
1 0SEC
3D
MIN.
First shot shown by E
the first shot. A timer
3 Take
is displayed after the first
3
shot; the second shot is taken when the timer reaches
zero. No operations can
be performed while the timer is active; if the
camera is turned off before the second shot is
taken, no picture will be recorded.
More on Photography
Select the delay between the two shots us1 ing
the k 3D INTERVAL TIME option in the
SHOOTING MODE
3D INTERVAL TIME
TURN
POWER MANAGEMENT
SET-UP
35
Playback Options
To view the most recent picture in the monitor,
press the a button.
100-0001
Choosing a Display Format
Press the DISP/BACK button to cycle through playback
display formats as shown below.
3D
More on Playback
Press the selector right to view pictures
in the order recorded, left to view pictures in reverse order. Keep the selector
pressed to scroll rapidly to the desired
frame.
Switching Between C and D
Press the 2D button to view C
3D
pictures in D, the 3D button to
view C pictures in C (D
pictures are always displayed in
D). In C playback, press the
R and S buttons to adjust parallax.
Indicators displayed
Indicators hidden
100-0001
3D
100-0001
2050
12 / 31
2 /13
Sort by date
Hide indicators for improved C viewing.
1 Note
Pictures taken using other cameras are indicated by a m (“gift image”) icon during playback.
36
Playback Options
Playback Zoom
Select T to zoom in on pictures displayed in single-frame playback; select W to zoom out. When
the picture is zoomed in, the selector can be used
to view areas of the image not currently visible in
the display.
Zoom indicator
Navigation window shows
portion of image currently
displayed in monitor
1 Note
Playback zoom is not available with cropped copies
saved at a size of a or copies created with O RESIZE (pg. 77).
BACK
More on Playback
Press DISP/BACK to exit zoom.
Intelligent Face Detection (D Only)
Pictures taken with Intelligent
Face Detection (pg. 64) are indicated by a g icon. Press the
R button to zoom in on the
FACE ZOOM
subject selected with Intelligent
Face Detection. You can then
use the zoom control to zoom in and out.
3 Caution: C Playback
C pictures are best viewed with the camera held
horizontally. The 3D effect may not be visible at high
zoom ratios or when the monitor is viewed at an angle.
If C pictures appear blurred even after parallax is adjusted, select D playback.
37
Playback Options
s Multi-Frame Playback
Sort by Date
To change the number of images displayed, select s (W) when a picture is
shown full-frame in the monitor.
Choose sort-by-date mode to view pictures taken
on a selected date.
Select s (W) to increase the number
of pictures displayed to five, nine, or a
hundred.
DISP/BACK until the sort-by-date
1 Press
screen is displayed.
2050
100-0001
3D
12 / 31
2 /13
Select T to reduce the number of images displayed.
Use the selector to highlight images and press
MENU/OK to view the highlighted image full frame.
In the nine- and hundred-frame displays, press
the selector up or down to view more pictures.
Use the selector up or down to
2 highlight
a date. Keep the selector
pressed to scroll rapidly to the desired date.
Press the selector left or right to
3 scroll
through the pictures taken
on the highlighted date. Keep the
selector pressed to scroll rapidly to
the desired frame.
38
A Deleting Pictures
The A ERASE option in the playback menu can be used to delete still pictures and movies, increasing
the amount of space available on the memory card or in internal memory (for information on deleting
pictures in single-frame playback, see page 18). Note that deleted pictures can not be recovered. Copy
important pictures to a computer or other storage device before proceeding.
Press MENU/OK to display the play1 back
menu.
the selector up or down to
2 Press
highlight A ERASE.
PLAYBACK MENU
Press the selector right to display de3 lete
options.
PLAYBACK MENU
PARALLAX CONTROL
ERASE
BACK
RED EYE REMOVAL
FRAME
IMAGE ROTATE
ALL FRAMES
PROTECT
COPY
MENU/OK to display options for
5 Press
the selected item (pg. 40).
2 Tips: Deleting Pictures
• When a memory card is inserted, pictures will be deleted from the memory card; otherwise, pictures will
be deleted from internal memory.
• Protected pictures can not be deleted. Remove protection from any pictures you wish to delete (pg. 73).
• If a message appears stating that the selected images
are part of a DPOF print order, press MENU/OK to delete
the pictures.
More on Playback
PARALLAX CONTROL
ERASE
RED EYE REMOVAL
IMAGE ROTATE
PROTECT
COPY
the selector up or down to
4 Press
highlight FRAME or ALL FRAMES.
39
A Deleting Pictures
■ FRAME
FRAME:: Deleting Selected Images
Selecting FRAME displays the
dialog shown at right.
■ ALL FRAMES
FRAMES:: Deleting All Images
ALL OK?
Selecting ALL FRAMES dis- IT MAYERASE
TAKE A WHILE
plays the confirmation shown
at right.
OK
ERASE OK?
YES
CANCEL
Press the selector left or right
to scroll through pictures and
press MENU/OK to delete the
current picture (the picture is
deleted immediately; be careful not delete the wrong picture).
Press DISP/BACK to exit when all the desired pictures have been deleted.
40
CANCEL
SET
Highlight OK and press MENU/
OK to delete all unprotected
pictures.
The dialog shown at right is displayed during deletion. Press
DISP/BACK to cancel before all
pictures have been deleted
CANCEL
(any pictures deleted before
the button was pressed can not be recovered).
F Recording Movies
Shoot short movies. C movies are recorded in 3D movie format (pg. 102), D movies in motion JPEG
format with stereo sound recorded via the built-in microphone (be careful not to cover the microphone during recording).
1 Press the F/B button.
3D
12s
STANDBY
3D to record movies in
2 Press
C, 2D to record movies in
Display shows
time available
3D
12s
STANDBY
D. The current mode is
Choosing the Frame Size
To choose the frame size when
MODE MENU
QUALITY
recording movies to a memory
43s
1m25s
card, press the F button and
Choose
select O QUALITY.
a (640 × 480 pixels) for better
quality, b (320 × 240 pixels) for longer movies (if no
memory card is inserted, movies will be recorded at a
frame size of b). Press MENU/OK to return to movie
recording mode.
shown in the monitor.
Movies
1 Auto Parallax
If ON is selected for i AUTO PARALLAX CONTROL (pg. 63), parallax will be adjusted automatically when the shutter button is pressed halfway.
If OFF is selected, adjust parallax manually before
recording begins (pg. 13).
41
F Recording Movies
3 Frame the scene using the zoom control.
12s
STANDBY
Zoom indicator
Zoom can not be adjusted once recording
begins.
the shutter button all the way down to
4 Press
start recording.
REC
3D
12s
z REC and time
remaining are
displayed
2 Tip
There is no need to keep the shutter button pressed
during recording.
1 Note
Focus is set when recording begins; exposure and
white balance are adjusted automatically throughout recording. The color and brightness of the image may vary from that displayed before recording
begins.
42
the shutter button halfway to end record5 Press
ing. Recording ends automatically when the
movie reaches maximum length or memory is
full.
3 Caution
The indicator lamp lights while movies are being recorded. Do not open the battery chamber cover during shooting or while the indicator lamp is lit. Failure to
observe this precaution could prevent the movie from
being played back.
a Viewing Movies
During playback, movies are
displayed in the monitor as
shown at right. The following
operations can be performed
while a movie is displayed:
Operation
Start/pause
playback
End
playback/
delete
100-006
3D
Progress is shown in the monitor during playback.
15s
Progress bar
PLAY
STOP
PAUSE
2 Tip: Viewing Movies on a Computer
Copy movies to the computer before viewing.
3 Cautions
• Do not cover the speaker during playback.
• Vertical or horizontal streaks may appear in movies
containing very bright subjects. This is normal and
does not indicate a malfunction.
Movies
Description
Press the selector down to start playback.
Press again to pause.
Press the selector up to end playback. If
playback is not in progress, pressing the
selector up will delete the current movie.
Press the selector right to advance, left to
Advance/ rewind. If playback is paused, the movie
rewind will advance or rewind one frame each
time the selector is pressed.
Press MENU/OK to pause playback and disAdjust play volume controls. Press the selector
volume up or down to adjust the volume; press
MENU/OK again to resume playback.
43
Viewing Pictures on TV
Connect the camera to a TV and tune the television to the video channel to show pictures to a group.
The optional A/V cable connects as shown below. Turn the camera off before connecting the cable.
Connect yellow plug
to video-in jack
Insert into A/V cable
connector
Connect white plug
to audio-in jack
Press a for about a second to turn the camera on. The camera monitor turns off and pictures are
played back on the TV, with C images displayed in D. Note that the camera volume controls have
no effect on sounds played on the TV; use the television volume controls to adjust the volume.
1 Note
Image quality drops during movie playback.
Connections
44
3 Caution
When connecting the cable, be sure the connectors are fully inserted.
Printing Pictures via USB (D Only)
If the printer supports PictBridge, the camera can be connected directly to the printer and
pictures can be printed without first being copied to a computer. Note that depending on the
printer, not all the functions described below may be supported.
Printing in C
C pictures in MPO format can not be printed via direct USB connection, although JPEG copies created when
MPO+JPEG is selected for o 3DREC can be printed in D (pg. 84). For information on C prints, visit http://
fujifilm.com/3d/print/.
Connecting the Camera
the supplied USB cable as shown and 2 Press the a button for about a second to turn
1 Connect
turn the printer on.
the camera on. t USB will be displayed in
the monitor, followed by the PictBridge display
shown below at right.
USB
PICTBRIDGE
TOTAL: 00000
FRAME
OK
SET
Connections
00 SHEETS
1 Notes
• Print pictures from internal memory or a memory card that has been formatted in the camera.
• Default printer page size and print quality settings are used when printing via direct USB connection.
45
Printing Pictures via USB (D Only)
Printing Selected Pictures
Press the selector left or right to dis1 play
a picture you wish to print.
1 Note
To print one copy of the current picture, proceed
directly to Step 3.
the selector up or down to
2 Press
choose the number of copies (up to
99). Repeat steps 1–2 to select additional pictures.
MENU/OK to display a confirma3 Press
tion dialog.
PRINT THESE FRAMES
TOTAL: 9 SHEETS
YES
CANCEL
4 Press MENU/OK to start printing.
46
2 Tip: Printing the Date of Recording
To print the date of recording on pictures, press DISP/
BACK in steps 1–2 to display the PictBridge menu (see
“Printing the DPOF Print Order,” below). Press the selector up or down to highlight PRINT WITH DATE s
and press MENU/OK to return to the PictBridge display
(to print pictures without the date of recording, select
PRINT WITHOUT DATE). To ensure that the date is correct, set the camera clock before taking pictures. Note
that the PRINT WITH DATE s option is only available
with printers that support date printing.
During Printing
The message shown at right is
PRINTING
displayed during printing. Press
DISP/BACK to cancel before all
pictures are printed (depending
CANCEL
on the printer, printing may end
before the current picture has printed).
If printing is interrupted, press a to turn the camera
off and then on again.
Disconnecting the Camera
Confirm that the above message is not displayed and
turn the camera off. Disconnect the USB cable.
Printing Pictures via USB (D Only)
Printing the DPOF Print Order
To print the print order created with K PRINT
ORDER (DPOF) in the playback F-mode menu
(pg. 69):
1
MENU/OK to display a confirma3 Press
tion dialog.
PRINT DPOF OK?
TOTAL: 9 SHEETS
In the PictBridge display, press DISP/
BACK to open the PictBridge menu.
the selector up or down to
2 Press
highlight u PRINT DPOF.
YES
CANCEL
4 Press MENU/OK to start printing.
PICTBRIDGE
PRINT WITH DATE
PRINT WITHOUT DATE
PRINT DPOF
Connections
47
Printing Pictures via USB (D Only)
Creating a DPOF Print Order
The K PRINT ORDER (DPOF) option in the playback F-mode menu can be used to create a digital “print order” for PictBridge-compatible printers
(pg. 47) or devices that support DPOF.
DPOF
DPOF (Digital Print Order Format) is standard
that allows pictures to be printed from “print
orders” stored in internal memory or on a
memory card. The information in the order
includes the pictures to be printed and the number
of copies of each picture.
Press MENU/OK and follow the steps below.
Press the selector left or right to dis1 play
a picture you wish to include in
or remove from the print order.
the selector up or down to
2 Press
choose the number of copies (up
to 99). To remove a picture from the
order, press the selector down until
the number of copies is 0.
PRINT ORDER (DPOF)
DPOF: 00001
■ WITH DATE s// WITHOUT DATE
To modify the DPOF print order, select K PRINT
ORDER (DPOF) in the playback F-mode menu
and press the selector up or down to highlight
WITH DATE s or WITHOUT DATE.
MODE MENU
IR COMMUNICATION
SLIDE SHOW
PRINT ORDER (DPOF)
WITH DATE
WITHOUT DATE
RESET ALL
48
WITH DATE s: Print date of recording on pictures.
WITHOUT DATE: Print pictures without
date.
Total number of prints
Number of copies
01 SHEETS
FRAME
SET
2 Tip: Intelligent Face Detection
If the current picture was created with Intelligent
Face Detection (pg. 64), pressing R sets the number of copies to the number of faces detected.
Printing Pictures via USB (D Only)
steps 1–2 to complete the
3 Repeat
print order. Press MENU/OK to save the
print order when settings are complete, or DISP/BACK to exit without changing the
print order.
The total number of prints is dis4 played
in the monitor. Press MENU/OK
to exit.
The pictures in the current
print order are indicated by a
u icon during playback.
■ RESET ALL
To cancel the current print or- RESET DPOF OK?
der, select RESET ALL in the
K PRINT ORDER (DPOF)
menu. The confirmation shown
YES
CANCEL
at right will be displayed; press
MENU/OK to remove all pictures from the order.
Connections
1 Notes
• Remove the memory card to create or modify a print
order for the pictures in internal memory.
• Print orders can contain a maximum of 999 pictures.
RESET DPOF OK?
• If a memory card is inserted containing a print order created by
another camera, the message
shown at right will be displayed.
YES
CANCEL
Pressing MENU/OK cancels the
print order; a new print order
must be created as described above.
49
Viewing Pictures on a Computer
The supplied FinePixViewer software can be used to copy pictures to a computer, where they can be
stored, viewed, organized, and printed. Before proceeding, install FinePixViewer as described below.
Do NOT connect the camera to the computer until installation is complete.
Installing FinePixViewer
that the computer meets the following system requirements:
1 ConfirmPreinstalled
versions of Windows Vista, Windows XP Home Edition (Service Pack 2), or Windows XP Professional
OS
(Service Pack 2)
• Windows Vista: 800 MHz Pentium 4 or better (3 GHz Pentium 4 or better recommended)
CPU
• Windows XP: 800 MHz Pentium 4 or better (2 GHz Pentium 4 or better recommended)
• Windows Vista: 512 MB or more (1 GB or more recommended)
RAM
• Windows XP: 512 MB or more
Free disk A minimum of 450 MB required for installation with 600 MB available when FinePixViewer is running (15 GB or
space more recommended under Windows Vista, 2 GB or more recommended under Windows XP)
Video 800 × 600 pixels or more with 16-bit color or better (1,024 × 768 pixels or more with 32-bit color recommended)
• Built-in USB port recommended. Operation is not guaranteed with other USB ports.
Other • Internet connection (56 kbps or faster recommended) required to use FinePix Internet Service; Internet connection and e-mail software required to use e-mail option.
3 Caution
For information about Windows 7, visit http://www.fujifilm.com/support/download/camera/software/. Other
versions of Windows are not supported. Operation is not guaranteed on home-built computers or computers
that have been upgraded from earlier versions of Windows.
2 Start the computer. Log in to an account with administrator privileges before proceeding.
50
Viewing Pictures on a Computer
3 Exit any applications that may be running and insert the installer CD in a CD-ROM drive.
Windows Vista
If an AutoPlay dialog is displayed, click SETUP.exe. A “User Account Control” dialog will then be displayed;
click Allow.
The installer will start automatically; click Installing FinePixViewer and follow the on-screen instructions to install FinePixViewer. Note that the Windows CD may be required during installation.
If the Installer Does Not Start Automatically
If the installer does not start automatically, select Computer or My Computer from the start menu, then
double-click the FINEPIX CD icon to open the FINEPIX CD window and double-click SETUP or SETUP.exe.
If prompted to install Windows Media Player or DirectX, follow the on-screen instructions to com4 plete
installation.
prompted, remove the installer CD from the CD-ROM drive and click Restart to restart the
5 When
computer. Store the installer CD in a dry location out of direct sunlight in case you need to re-install
Installation is now complete. Proceed to “Connecting the Camera” on page 52. Note that the Windows
CD may be required when the camera is connected for the first time.
Connections
the software. The version number is printed at the top of the CD label for reference when updating
the software or contacting customer support.
51
Viewing Pictures on a Computer
Connecting the Camera
the pictures you wish to copy are stored on a 3 Press the a button for about a second to turn
1 Ifmemory
card, insert the card into the camera
the camera on. FinePixViewer will start auto(pg. 7). If no card is inserted, pictures will be
copied from internal memory.
3 Caution
Loss of power during transfer could result in loss of
data or damage to internal memory or the memory
card. Charge the battery before connecting the
camera.
Turn the camera off and connect the supplied
2 USB
cable as shown, making sure the connectors are fully inserted. Connect the camera directly to the computer; do not use a USB hub
or keyboard.
matically and the “Save Image Wizard” will be
displayed. Follow the on-screen instructions to
copy pictures to the computer. To exit without
copying pictures, click Cancel.
3 Caution
If FinePixViewer does not start automatically, the
software may not be correctly installed. Disconnect
the camera and reinstall the software.
For more information on using FinePixViewer,
select How to Use FinePixViewer in the
FinePixViewer Help menu.
1 Note
The camera will not turn off automatically while connected to a computer.
52
Viewing Pictures on a Computer
Disconnecting the Camera
After confirming that the indicator lamp is out, follow
the on-screen instructions to turn the camera off and
disconnect the USB cable.
Updating FinePixViewer
The latest version of FinePixViewer can be downloaded from http://www.fujifilm.com/.
Uninstalling FinePixViewer
Only uninstall FinePixViewer before reinstalling the
software or when it is no longer required. After quitting FinePixViewer and disconnecting the camera,
open the control panel and use “Programs and Features” (Windows Vista) or “Add or Remove Programs”
(Windows XP) to uninstall FinePixViewer, FinePix
Resource, and FinePix Studio. Under Windows, one
or more confirmation dialogs may be displayed; read
the contents carefully before clicking OK.
Connections
3 Cautions
• Use only memory cards that have been formatted
in the camera and contain pictures taken with the
camera. If a memory card containing a large number
of images is inserted, there may be a delay before
FinePixViewer starts and FinePixViewer may be unable to import or save images. Use a memory card
reader to transfer pictures.
• Make sure the indicator lamp is out before turning the
camera off or disconnecting the USB cable. Failure to
observe this precaution could result in loss of data or
damage to internal memory or the memory card.
• Disconnect the camera before inserting or removing
memory cards.
• In some cases, it may not be possible to access pictures saved to a network server using FinePixViewer
in the same way as on a standalone computer.
• The user bears all applicable fees charged by the
phone company or Internet service provider when
using services that require an Internet connection.
53
IR Communication
Still pictures can be copied from the camera to any device that supports high-speed infrared or
IrSimple, including the optional FinePix REAL 3D V1 digital viewer. The camera can receive still pictures
from devices that support high-speed infrared or IrSimpleShot™ (IRSS™). Before sharing pictures, match
the M IR COMMUNICATION option in the camera setup menu to the infrared transmission type used
by the other device (pg. 81). For details, see the manual provided with the device.
To share pictures, place the camera about 5 to 20 cm from the other device with
the infrared ports pointing directly at each other. The ports should be at no more
than a 15 ° angle. Be sure both devices are on.
Maximum angle: approximately 15 °
3 Caution
Make sure that there are no obstacles between the two devices and that the infrared ports are correctly aligned
and are not in direct sunlight or directly under a fluorescent light. Remote controls and other infrared devices and
equipment that generates electrical noise may interfere with transmission.
2 Tips
• For information on supported infrared devices, consult the compatibility information for this camera at the following website: http://fujifilm.com/products/digital_cameras/support/ir.html.
• C images can only be transmitted to supported devices. Play images back in D before transmitting them to
other devices.
54
IR Communication
Sending Pictures to Other Devices
Press the F button and select M IR
COMMUNICATION in the F-mode
menu. Pictures are displayed as
shown below.
1
the F button to begin trans3 Press
mission.
IR COMMUNICATION
TRANSMITTING DATA
IR COMMUNICATION
CANCEL
TRANSMIT
CANCEL
RECEIVE
TRANSMISSION COMPLETED will appear in
the monitor when transmission is complete.
Press the selector left or right to dis2 play
a picture you wish to send.
Connections
55
IR Communication
Receiving Pictures from Other Devices
Press the F button and select M IR
COMMUNICATION in the F-mode
menu.
1
MENU/OK on the receiving de3 Press
vice to begin transmission.
IR COMMUNICATION
RECEIVING DATA
IR COMMUNICATION
CANCEL
TRANSMIT
CANCEL
2
RECEIVE
On the sending device, select the
picture to be transmitted.
DATA RECEIVED will appear in the monitor
when transmission is complete. Pictures received from other devices are indicated by a
m (“gift”) icon during playback.
3 Cautions
• If an error is displayed during transmission, press MENU/OK to retransmit the picture or press DISP/BACK to cancel.
• Image size may be reduced for transmission. O- and P-size pictures are converted to size Q (pg. 59).
• Movies can not be shared via infrared. C pictures displayed in D are converted to JPEG for transmission;
otherwise, C pictures are transmitted in C format.
56
Using the Menus: Shooting Mode
The F-mode and shooting menus contain settings for a wide range of shooting conditions.
Using the F-Mode Menu
the F button to display the
1 Press
F-mode menu.
the selector up or down to
4 Press
highlight the desired option.
MODE MENU
ISO
IMAGE SIZE
IMAGE QUALITY
COLOR
AUTO
4:3
N
STD
MENU/OK to select the high5 Press
lighted option.
the selector up or down to
2 Press
highlight the desired menu item.
Press the selector right to display op3 tions
for the highlighted item.
MODE MENU
N
FINE
NORMAL
Menus
AUTO
4:3
IMAGE QUALITY
STD
57
Using the Menus: Shooting Mode
F-Mode Menu Options
Menu item
Description
Options
Default
Adjust ISO sensitivity (pg. 59). Choose higher values when the
N ISO
AUTO / 1600 / 800 / 400 / 200 / 100 AUTO
subject is poorly lit.
O4:3/O3:2/
O IMAGE SIZE
Choose image size and aspect ratio (pg. 59).
O4:3
P4:3/Q4:3
T IMAGE QUALITY
Choose image quality (pg. 60).
F/N
N
D WHITE BALANCE
Adjust color for different light sources (pg. 60).
AUTO/i/j/k/l/m/n/g AUTO
Shoot pictures in standard or saturated color or in black-andSTD/a/b
STD
P G COLOR
white (pg. 61).
Adjust exposure for bright, dark, or high-contrast scenes in
d SET SHUTTERSPEED,
—
—
APERTURE.
modes M (pg. 29).
Adjust exposure for bright, dark, or high-contrast scenes in
d SETTING APERTURE
—
—
modes A (pg. 30).
Adjust exposure for bright, dark, or high-contrast scenes in
d EXP. COMPENSATION
—
—
mode P (pg. 31).
1 Note
Some options are not available in all shooting modes.
58
Using the Menus: Shooting Mode
N ISO
Control the camera’s sensitivity to light. Higher
values can be used to reduce blur when lighting
is poor; note, however, that mottling may appear
in pictures taken at high sensitivities. If AUTO is
selected, the camera will adjust sensitivity automatically in response to shooting conditions.
Settings other than AUTO are
shown by an icon in the display.
M
ISO 100
1 Note
Sensitivity is not reset when the camera is turned off.
O IMAGE SIZE
Choose the size and aspect ratio at which still pictures are recorded. Large pictures can be printed
at large sizes with no drop in quality; small pictures require less memory, allowing more pictures
to be recorded.
Option
O4:3
O3:2
P4:3
Q4:3
Prints at sizes up to
31 × 23 cm (12.2 × 9.1 in.)
31 × 21 cm (12.2 × 8.1 in.)
22 × 16 cm (8.6 × 6.5 in.)
17 × 13 cm (6.8 × 5.1 in.)
The number of pictures that can be taken at current settings (pg. 104) is shown to the right of the
image quality icon in the display.
1 Note
Image quality is not reset when the camera is turned
off or another shooting mode is selected.
Menus
59
Using the Menus: Shooting Mode
T IMAGE QUALITY
Choose how much image files are compressed.
Select FINE (low compression) for higher image
quality, NORMAL (high compression) to increase
the number of pictures that can be stored.
D WHITE BALANCE
For natural colors, choose a setting that matches
the light source (for an explanation of “white balance,” see the Glossary on page 103).
Option
Description
AUTO White balance adjusted automatically.
i
j
k
l
m
n
g
For subjects in direct sunlight.
For subjects in the shade.
Use under “daylight” fluorescent lights.
Use under “warm white” fluorescent lights.
Use under “cool white” fluorescent lights.
Use under incandescent lighting.
For underwater subjects in an aquarium.
If AUTO does not produce the desired results (for
example, when taking close-ups), choose the option that matches the light source.
1 Notes
• Auto white balance is used with the flash. Turn the
flash off (pg. 23) to take pictures at other settings.
• Results vary with shooting conditions. Play pictures
back after shooting to check colors in the monitor.
60
Using the Menus: Shooting Mode
P G COLOR
Enhance contrast and color saturation or take pictures in black and white.
Option
Displayed in
F-STANDARD Standard contrast and saturation. Recommended in most situations.
Vivid contrast and color. Choose for vivid shots of flowers or enhanced greens and blues in
aF-CHROME
landscapes. Not available in SP mode.
Take pictures in black and white.
bF-B&W
Settings other than F-STANDARD are shown by an icon in the monitor.
1 Notes
• P G COLOR is not reset when the camera is turned off or another shooting mode is selected.
• Depending on the subject, the effects of aF-CHROME may not be visible in the monitor.
Menus
61
Using the Menus: Shooting Mode
Using the Shooting Menu
Press MENU/OK to display the shoot1 ing
menu.
the selector up or down to
4 Press
highlight the desired option.
SHOOTING MENU
FACE DETECTION
CONTINUOUS
POWER MANAGEMENT
AUTO PARALLAX CONTROL
SET-UP
OFF
ON
the selector up or down to
2 Press
highlight the desired menu item.
Press the selector right to display op3 tions
for the highlighted item.
SHOOTING MENU
FACE DETECTION
CONTINUOUS
OFF
POWER MANAGEMENT
POWER SAVE
AUTO PARALLAX CONTROL
OFF
QUICK AF
SET-UP
62
MENU/OK to select the high5 Press
lighted option.
Using the Menus: Shooting Mode
Shooting Menu Options
Menu item
A SCENE POSITION
A SHOOTING MODE
(twin camera mode)
A SHOOTING MODE
(advanced C)
Description
Options
C/D/L/M/N/O/H/
Q/R/S/F/U/E
Default
Choose a D shooting mode for B mode (pg. 31).
V/X/W
V
Choose a C shooting mode for A mode (pg. 33).
B/A
B
q /g / OFF
q
J/I/ OFF
OFF
a/b/c
a
MIN. / 1.0 / 1.5 / 2.0 /
3.0 / 5.0 / 10
MIN.
G/H
G
o/p/q
r/s
o
r
n/p
n
ON/ OFF
ON
W/X/Y/Z/V
—
Choose a scene for SP mode (pg. 27).
Menus
Choose whether the camera automatically detects and
sets focus and exposure for human portrait subjects. Can
be combined with red-eye removal (pg. 64).
Shoot a series of pictures (pg. 65).
R CONTINUOUS
Choose color reproduction options for pictures recorded
j 2-COLOR SETTING
using X 2-COLOR (pg. 32).
Choose the time lag for pictures recorded with
k 3D INTERVAL TIME
B INTERVAL 3D SHOOTING (pg. 35).
Choose the order in which pictures are taken in A
l TURN
mode (pg. 34, 35).
Choose how the camera meters exposure (pg. 66).
C PHOTOMETRY
Choose how the camera selects a focus area (pg. 66).
F 2D AF MODE
Optimize camera performance for increased battery life
S POWER MANAGEMENT
or quick focus (pg. 67).
i AUTO PARALLAX CONTROL Choose ON for auto C parallax adjustment (pg. 13).
Perform basic camera setup such as choosing a language
M SET-UP
and setting the time and date (pg. 78).
b FACE DETECTION
C
1 Note
Some options are not available in all shooting modes.
63
Using the Menus: Shooting Mode
b FACE DETECTION (D
(D Only)
Intelligent Face Detection allows the camera to
automatically detect human faces and set focus
and exposure for a face anywhere in the frame for
shots that emphasize portrait subjects. Choose
for group portraits (in vertical or horizontal orientations) to prevent the camera from focusing on
the background. Intelligent Face Detection also
offers a red-eye removal option for removing
“red-eye” effects caused by the flash.
• g ON J ON: Intelligent Face Detection and redeye removal on. Use with the flash.
• g ON J OFF: Intelligent Face Detection on; redeye removal off.
• OFF: Intelligent Face Detection and red-eye removal off.
2 Tip: Red-Eye Removal
When red-eye removal is on, pictures are processed to
reduce red-eye before being recorded. Select ON for
B SAVE ORG IMAGE in the setup menu (pg. 80) to
save unprocessed copies of pictures created with redeye removal.
64
2 Tip: Intelligent Face Detection
The selected face is indicated by a AUTO
3D
green border (note that, in some
shooting modes, exposure is adjusted for the current shooting
mode and may not be optimized
for the selected subject). If more
Green border
than one face is detected, the
camera will select the face closest to the center of the
frame; other faces are indicated by white borders (note
that some time may be required for face detection if
the number of faces is very large). Intelligent Face Detection is recommended when using the self-timer for
group- or self-portraits (pg. 26).
When a picture taken with Intelligent Face Detection
is displayed, the camera can automatically select faces
for red-eye removal (pg. 71), playback zoom (pg. 37),
slide shows (pg. 69), printing (pg. 48), and cropping
(pg. 76).
Using the Menus: Shooting Mode
3 Cautions
• If no face is detected when the shutter button is
pressed halfway (pg. 17), the camera will focus on the
subject at the center of the display and red-eye will
not be removed.
• If the subject moves as the shutter button is pressed,
their face may not be in the area indicated by the
green border when the picture is taken.
R CONTINUOUS
Capture motion in a series of pictures.
• J TOP 40 (HIGH SPEED): The camera takes up to 40
pictures at high speed while the shutter button
is pressed. Not available in C.
• I TOP 40: The camera takes up to 40 pictures
while the shutter button is pressed.
• OFF: The camera takes one picture each time the
shutter button is pressed.
1 Notes
• The flash turns off automatically. The previously-selected flash mode is restored when OFF is selected
for R CONTINUOUS.
• Frame rate varies with shutter speed.
Menus
65
Using the Menus: Shooting Mode
C PHOTOMETRY
Choose how the camera meters exposure when
Intelligent Face Detection (pg. 64) is off.
• o MULTI: Automatic scene recognition is used
to adjust exposure for a wide range of shooting
conditions.
• p SPOT: The camera meters lighting conditions
at the center of the frame. Recommended when
the background is much brighter or darker than
the main subject. Can be used with focus lock
(pg. 20) to meter off-center subjects.
• q AVERAGE: Exposure is set to the average for
the entire frame. Provides consistent exposure
across multiple shots with the same lighting,
and is particularly effective for landscapes and
portraits of subjects dressed in black or white.
F 2D AF MODE ((D
D Only)
This option controls how the camera selects the
focus area. Regardless of the option selected, the
camera will focus on the subject in the center of
the monitor when macro mode is on (pg. 22).
• r CENTER: The camera focus- M
2D
es on the subject in the center of the frame. This option
can be used with focus lock.
• s MULTI: When the shutter button is pressed
halfway, the camera detects high-contrast subjects near the center of the frame and selects
the focus area automatically (if the focus frame is
not displayed, select r CENTER and use focus
lock; pg. 20).
M
2D
Press
halfway
Focus frame
66
Using the Menus: Shooting Mode
S POWER MANAGEMENT
Optimize camera performance for increased battery life or quick focus response.
• n POWER SAVE: Monitor refresh rate is reduced. If no operations are performed for 10 s, the monitor
will dim automatically to save power. This option is recommended when the camera is used for
extended periods at high temperatures to prevent mottled vertical streaks from appearing in photographs.
• p QUICK AF: Reduces focusing time, ensuring a quick shutter response. The monitor dims to save power only if no operations are performed for 30 s. An icon appears in the display.
1 Notes
• n POWER SAVE does not take effect when Intelligent Face Detection is on.
• If OFF is selected for M AUTO POWER OFF, changing the option selected for S POWER MANAGEMENT
resets M AUTO POWER OFF to 5 MIN (pg. 85).
Menus
67
Using the Menus: Playback Mode
The F-mode and playback menus are used to manage the pictures in internal memory or on the
memory card.
Using the F-Mode Menu
the a button to enter play1 Press
back mode (pg. 36).
the F button to display the
2 Press
F-mode menu.
MODE MENU
IR COMMUNICATION
SLIDE SHOW
PRINT ORDER (DPOF)
the selector up or down to
3 Press
highlight the desired menu item.
68
Press the selector right to display op4 tions
for the highlighted item.
MODE MENU
IR COMMUNICATION
NORMAL
SLIDE SHOW
NORMAL
PRINT ORDER (DPOF)
FADE-IN
FADE-IN
MULTIPLE
3D FADE
the selector up or down to
5 Press
highlight the desired option.
MENU/OK to select the high6 Press
lighted option.
Using the Menus: Playback Mode
F-Mode Menu Options
Option
Description
Copy pictures to other devices via inM IR COMMUNICATION
frared (pg 54).
View pictures in a slide show.
I SLIDE SHOW
Select pictures for printing on DPOFK PRINT ORDER (DPOF) and PictBridge-compatible devices
(pg. 47, 48).
I SLIDE SHOW
View pictures in an automated slide show. Choose
the type of show and press MENU/OK to start. Press
DISP/BACK at any time during the show to view onscreen help. When a movie is displayed, movie playback will begin automatically, and the slide show
will continue when the movie ends. The show can
be ended at any time by pressing MENU/OK.
Option
Displayed in
Press selector left or right to go back or
skip ahead one frame. Select FADE-IN
FADE-IN for fade transitions between frames.
NORMAL g As above, except that camera automatically zooms in on faces selected with
FADE-IN g Intelligent Face detection.
MULTIPLE Display several pictures at once.
3D FADE C images fade in from D to C.
NORMAL
Menus
1 Note
The camera will not turn off automatically while a slide
show is in progress.
69
Using the Menus: Playback Mode
Using the Playback Menu
1 Press a to enter playback mode.
Press MENU/OK to display the play2 back
menu.
the selector up or down to
5 Press
highlight the desired option.
MENU/OK to select the high6 Press
lighted option.
PLAYBACK MENU
PARALLAX CONTROL
ERASE
RED EYE REMOVAL
IMAGE ROTATE
PROTECT
COPY
the selector up or down to
3 Press
highlight the desired menu item.
Playback Menu Options
The following options are available:
Option
i PARALLAX CONTROL
A ERASE
B RED EYE REMOVAL
4
C IMAGE ROTATE
Press the selector right to display options for the highlighted item.
PLAYBACK MENU
PARALLAX CONTROL
ERASE
BACK
RED EYE REMOVAL
FRAME
IMAGE ROTATE
ALL FRAMES
PROTECT
COPY
70
D PROTECT
E COPY
G CROP
O RESIZE
M SET-UP
Description
Create copies of C pictures with
modified parallax (pg. 71).
Delete all or selected pictures (pg. 39).
Create copies with reduced red eye (pg.
71).
Rotate pictures (pg. 72).
Protect pictures from accidental deletion (pg. 73).
Copy pictures between internal memory and a memory card (pg. 74).
Create cropped copies of pictures (pg.
76).
Create small copies of pictures (pg. 77).
Perform basic camera setup (pg. 78).
Using the Menus: Playback Mode
i PARALLAX CONTROL (C
(C Only)
If the current picture is marked with a g icon to
indicate that it was taken in C, this option can
be used to create a copy with modified parallax.
Press R or S to adjust parallax (pg. 13), then select
i PARALLAX CONTROL in the playback menu
and press MENU/OK to create a copy with modified
parallax.
100-0001
PLAYBACK MENU
3D
PARALLAX CONTROL
ERASE
RED EYE REMOVAL
IMAGE ROTATE
PROTECT
COPY
0
CORRECTION
STORE
B RED EYE REMOVAL ((D
D Only)
If the current picture is marked with a g icon to
indicate that it was taken with Intelligent Face Detection, this option can be used to remove redeye. The camera will analyze the image; if red-eye
is detected, the image will be processed to create
a copy with reduced red-eye.
PLAYBACK MENU
REMOVAL OK?
PARALLAX CONTROL
ERASE
RED EYE REMOVAL
IMAGE ROTATE
PROTECT
COPY
YES
CANCEL
CANCEL
Menus
1 Notes
• Red eye may not be removed if the camera is unable
to detect a face or the face is in profile. Results may
differ depending on the scene. Red eye can not be
removed from pictures that have already been processed using red-eye removal or pictures created
with other devices.
• The amount of time needed to process the image
varies with the number of faces detected.
• Copies created with B RED EYE REMOVAL are indicated by a e icon during playback.
71
Using the Menus: Playback Mode
C IMAGE ROTATE (D
(D Only)
By default, pictures taken in IMAGE ROTATE
tall orientation are displayed
in wide orientation. Use this
option to display pictures in
SET
CANCEL
the correct orientation in the
monitor. It has no effect on pictures displayed on
a computer or other device.
Press the selector down to rotate the
1 picture
90 ° clockwise, up to rotate
the picture 90 ° counterclockwise.
1 Notes
• C images and protected pictures can not be rotated. Remove protection before rotating D images
(pg. 73).
• The camera may not be able to rotate pictures created with other devices.
To rotate a picture, play the picture back and select C IMAGE ROTATE in the playback menu.
MENU/OK to confirm the opera2 Press
tion (to exit without rotating the picture, press DISP/BACK).
The next time the picture is played back, it will
automatically be rotated.
72
Using the Menus: Playback Mode
D PROTECT
Protect pictures from accidental deletion. The following options are available.
■ FRAME
Protect selected pictures.
Press the selector left or right to display the desired picture.
1
PROTECT OK?
YES
UNPROTECT OK?
CANCEL
Picture not protected
YES
CANCEL
Protected picture
MENU/OK to protect the picture.
2 Press
If the picture is already protected,
pressing MENU/OK will remove protection from the image.
when the operation is complete.
■ RESET ALL
Press MENU/OK to remove protection from all pictures, or
press DISP/BACK to exit without
changing picture status.
SET ALL OK?
IT MAY TAKE A WHILE
YES
CANCEL
RESET ALL OK?
IT MAY TAKE A WHILE
YES
CANCEL
If the number of pictures affected is very large, the display at right will appear in the
monitor while the operation is
CANCEL
in progress. Press DISP/BACK to
exit before the operation is complete.
3 Caution
Protected pictures will be deleted when the memory
card or internal memory is formatted (pg. 85).
Menus
steps 1–2 to protect addi3 Repeat
tional images. Press DISP/BACK to exit
■ SET ALL
Press MENU/OK to protect all
pictures, or press DISP/BACK to
exit without changing picture
status.
73
Using the Menus: Playback Mode
E COPY
Copy pictures between internal memory and a memory card.
the selector up or down to
1 Press
highlight a INTERNAL MEMORY
y b CARD (copy from internal
memory to the memory card) or
b CARD y a INTERNAL MEMORY (copy from a memory card to
internal memory).
Press the selector right to display op2 tions
for the highlighted item.
COPY
INTERNAL MEMORY
74
CARD
CARD
FRAME
INTERNAL
MEMORY
ALL
FRAMES
YES
CANCEL
the selector up or down to
3 Press
highlight FRAME or ALL FRAMES.
4 Press MENU/OK.
2 Tip: Copying Pictures Between Memory Cards
To copy pictures between two memory cards, insert
the source card and copy the pictures to internal memory, then remove the source card, insert the destination
card, and copy the pictures from internal memory.
Using the Menus: Playback Mode
■ FRAME
Copy selected frames.
COPY OK?
100-0001
YES
Press the selector left or right to dis1 play
the desired picture.
CANCEL
■ ALL FRAMES
Press MENU/OK to copy all pictures, or press DISP/BACK to exit
without copying pictures.
COPY ALL OK?
100-0001
IT MAY TAKE
A WHILE
YES
CANCEL
3 Cautions
• Copying ends when the destination is full.
• DPOF print information is not copied (pg. 48).
2 Press MENU/OK to copy the picture.
steps 1–2 to copy additional
3 Repeat
images. Press DISP/BACK to exit when
the operation is complete.
Menus
75
Using the Menus: Playback Mode
G CROP
To create a cropped copy of a picture, play the picture back and select G CROP in the playback menu
(pg. 70).
Use the zoom control to zoom in and out and 2 Press MENU/OK. A confirmation dia1 use
the selector to scroll the picture until the
log will be displayed.
desired portion is displayed (to exit to singleframe playback without creating a cropped
copy, press DISP/BACK).
Zoom indicator
CROP
YES
CANCEL
Navigation window
shows portion of image currently displayed
in monitor
If the size of the final copy will be a, OK will
be displayed in yellow.
2 Tip: Intelligent Face Detection (D Only)
CROP
If the picture was shot with
Intelligent Face Detection (pg.
64), g will be displayed in the
monitor. Press the R button
FACE CROPPING
YES
CANCEL
to zoom in on the selected
face.
76
REC OK?
REC
CANCEL
Copy size (P, Q, or a) is shown at the top.
Larger crops produce larger copies; all copies
have an aspect ratio of 4 : 3.
MENU/OK to save the cropped
3 Press
copy to a separate file.
Using the Menus: Playback Mode
O RESIZE
To create a small copy of a picture, play the picture back and select O RESIZE in the playback menu
(pg. 70).
the selector up or down
1 Press
to highlight a STANDARD or
b SMALL.
MENU/OK to select the high2 Press
lighted option.
MENU/OK to copy the picture at
3 Press
the selected size.
Menus
77
The Setup Menu
Using the Setup Menu
the setup menu.
1 Display
1.1 Press MENU/OK to display
the
menu for the current mode.
1.2 Press the selector up or down
to highlight M SET-UP.
2 Choose a page.
2.1 Press the selector left or right to
choose a page.
SET-UP
FORMAT
AUTO POWER OFF
TIME DIFFERENCE
BACKGROUND COLOR
GUIDANCE DISPLAY
1.3 Press the selector right to display the setup menu.
SET-UP
IMAGE DISP.
FRAME NO.
SAVE ORG IMAGE
ILLUMINATION
DIGITAL ZOOM
3DREC
78
1.5 SEC
CONT.
OFF
ON
OFF
MPO+JPEG
ENGLISH
2 MIN
ON
2.2 Press the selector down to enter the menu.
The Setup Menu
Adjust settings.
3 3.1
Press the selector up or down
to highlight a menu item.
3.3 Press the selector up or down
to highlight an option.
SET-UP
FORMAT
AUTO POWER OFF
TIME DIFFERENCE
BACKGROUND COLOR
GUIDANCE DISPLAY
ENGLISH
2 MIN
ON
3.4 Press MENU/OK to select the
highlighted option.
3.2 Press the selector right to display options for the highlighted
item.
SET-UP
FORMAT
AUTO POWER OFF
TIME DIFFERENCE
BACKGROUND COLOR
GUIDANCE DISPLAY
ENGLISH
5 MIN
2 MIN
2 MIN
OFF
ON
Menus
79
The Setup Menu
Setup Menu Options
Menu item
Description
Options
Choose how long pictures are displayed after shooting (pg.
A IMAGE DISP.
3 SEC / 1.5 SEC /ZOOM / OFF
82).
B FRAME NO.
Choose how files are named (pg. 83).
CONT. / RENEW
Choose whether to save unprocessed copies of pictures
B SAVE ORG IMAGE
ON / OFF
taken using red-eye removal.
W
If ON is selected, the shooting indicator will light when the
a ILLUMINATION
camera is turned on. It will also light after a picture is taken
ON / OFF
to let the subjects know that shooting is complete.
D DIGITAL ZOOM
Enable or disable digital zoom (pg. 84).
ON / OFF
Choose MPO+JPEG to save JPEG copies of C images (pg.
o 3DREC
MPO+JPEG / MPO
84).
F DATE/TIME
Set the camera clock (pg.11).
—
G OPERATION VOL.
Adjust the volume of camera controls.
b (high) / c (mid) /
d (low) / e OFF (mute)
H SHUTTER VOLUME
Adjust the volume of the shutter sound.
X
e SHUTTER SOUND
Choose the sound made by the shutter.
i/j
I PLAYBACK VOLUME Adjust the volume for movie playback (pg. 84).
—
J LCD BRIGHTNESS
Control the brightness of the display (pg. 84).
—
K FORMAT
Format internal memory or memory cards (pg. 85).
—
Choose a language (pg.11).
See page 107
La
M AUTO POWER OFF
Choose the auto power off delay (pg. 85).
5 MIN / 2 MIN / OFF
Y
N TIME DIFFERENCE
Set the clock to local time (pg. 86).
h/g
—
O BACKGROUND COLOR Choose a color scheme for menus and cursors.
c GUIDANCE DISPLAY Choose whether to display tool tips.
ON / OFF
80
Default
1.5 SEC
CONT.
OFF
ON
OFF
MPO+JPEG
—
c
i
7
0
—
ENGLISH
2 MIN
h
—
ON
The Setup Menu
Menu item
Description
Choose a video mode for connection to a TV (pg. 44).
Choose a standard for infrared transmission: STANDARD
M IR COMMUNICATION for use with cameras, printers, or digital viewers, IrSS for use
with TVs (pg. 54).
p 3D LEVEL
Choose the amount of 3D effect in the setup menu.
Disable C to prevent fatigue or display a warning after 30
r 3D CAUTION DISP
Z
minutes of use (pg. 87).
q OPT AXIS CONTROL Align the optical axes of the twin lenses (pg. 87).
Reset all settings except F DATE/TIME, N TIME DIFFERENCE, O BACKGROUND COLOR, and Q VIDEO
R RESET
SYSTEM to default values. A confirmation dialog will be
displayed, press the selector left or right to highlight OK
and press MENU/OK.
If ON is selected when the camera is powered by an AC power adapter, a demo will play when the camera is turned on.
V s DEMO MODE
Press the shutter button to exit demo mode.
Q VIDEO SYSTEM
Options
NTSC / PAL
Default
—
STD / IrSS
STD
OFF / LEVEL 1–3
LEVEL 1
ON / OFF / NOT 3D
ON
—
0
—
—
ON / OFF
ON
Menus
81
The Setup Menu
A IMAGE DISP.
Choose how long pictures are displayed in the monitor after shooting.
• 3 SEC/1.5 SEC: Pictures are displayed for the specified time before being recorded to the memory card.
Colors may differ from those in the final picture.
• ZOOM (CONTINUOUS): Pictures are displayed until the MENU/OK button is pressed. Pictures can be zoomed
in to check fine details. Not available in C or B mode or when an option other than OFF is
selected for R CONTINUOUS (pg. 65).
• OFF: Pictures are not automatically displayed after shooting.
82
The Setup Menu
B FRAME NO.
New pictures are stored in image files named using a four-digit file number as- Frame number
100-0001
signed by adding one to the last file number used. The file number is displayed during playback as shown at right. B FRAME NO. controls whether file numbering is Directory
File
reset to 0001 when a new memory card is inserted or the current memory card or number number
internal memory is formatted.
• CONTINUOUS: Numbering continues from the last file number used or the first available file number,
whichever is higher. Choose this option to reduce the number of pictures with duplicate file names.
• RENEW: Numbering is reset to 0001 after formatting or when a new memory card is inserted.
1 Notes
• If the frame number reaches 999-9999, the shutter release will be disabled (pg. 100).
• Selecting R RESET (pg. 81) resets B FRAME NO. to CONTINUOUS but does not reset frame numbering.
• Frame numbers for pictures taken with other cameras may differ.
Menus
83
The Setup Menu
D DIGITAL ZOOM (D
(D Only)
If ON is selected, selecting T at the maximum
optical zoom position will trigger digital zoom,
further magnifying the image. To cancel digital
zoom, zoom out to the minimum digital zoom
position and select W.
AUTO
Zoom
indicator
Zoom indicator,
DIGITAL ZOOM off
W
Zoom indicator,
DIGITAL ZOOM on
T W
Optical zoom
Optical zoom
T
Digital
zoom
3 Caution
Digital zoom produces lower quality images than optical zoom.
84
o 3DREC
Choose MPO to save C images in multi-picture
(MPO) format, MPO+JPEG to save a JPEG copy in
addition to the multi-picture file. For information
on file formats, see the Glossary on page 102.
1 Note
MPO files can not be printed in D (pg. 45). The supplied FinePixViewer is required to view MPO files on a
computer (pg. 50).
I PLAYBACK VOLUME
Press the selector up or down
to choose volume for movie
playback and press MENU/OK to
select.
J LCD BRIGHTNESS
Press the selector up or down
to choose display brightness
and press MENU/OK to select.
VOLUME
7
SET
CANCEL
LCD BRIGHTNESS
0
SET
CANCEL
The Setup Menu
K FORMAT
FORMAT
Format internal memory or
FORMAT OK?
a memory card. If a memory ERASE ALL DATA
card is inserted in the camOK
CANCEL
era, this option will format the
SET
memory card. If no memory
card is inserted, a will be displayed in the format
dialog and this option will format internal memory. Press the selector left to highlight OK and
press MENU/OK to begin formatting.
3 Cautions
• All data—including protected pictures—will be deleted. Be sure important files have been copied to a
computer or other storage device.
• Do not open the battery-chamber cover during formatting.
M AUTO POWER OFF
Choose the length of time before the camera
turns off automatically when no operations are
performed. Shorter times increase battery life; if
OFF is selected, the camera must be turned off
manually (note that the camera will turn off automatically after five minutes if p QUICK AF is
selected for S POWER MANAGEMENT or if the
camera enters standby while in movie mode). Regardless of the option selected, the camera will
not turn off automatically when connected to a
printer (pg. 45) or computer (pg. 50) or when a
slide show is in progress (pg. 69).
2 Tip: Reactivating the Camera
To reactivate the camera after it has turned off automatically, open the lens cover or press the a button
for about a second (pg. 10).
Menus
85
The Setup Menu
N TIME DIFFERENCE
When traveling, use this option to switch the camera clock instantly from your home time zone to the
local time at your destination.
the difference between local time
1 Specify
and your home time zone.
1.1 Press the selector up or down
to highlight g LOCAL.
1.2 Press the selector right to display the time difference.
TIME DIFFERENCE
12 / 31 / 2050 10:00 AM
12 / 31 / 2050 10:00 AM
Switch between local time and your home
2 time
zone.
To set the camera clock to local time, highlight g LOCAL and press MENU/OK. To set
the clock to the time in your home time
zone, select h HOME. If g LOCAL is selected, g will be displayed in the monitor
for three seconds after the camera enters
shooting mode, and the date will be displayed in yellow.
AUTO
00
SET
:
00
CANCEL
1.3 Press the selector left or right
to highlight +, –, hours, or minutes; press up or down to edit.
The minimum increment is 15
minutes.
1.4 Press MENU/OK when settings
are complete.
86
12 / 31 / 2050
10 : 00 AM
After changing time zones, check that the
date and time are correct.
The Setup Menu
r 3D CAUTION DISP
To prevent fatigue, C can be disabled or a warning can be displayed after prolonged use.
• ON: C enabled, but a warning is displayed after
30 minutes of continuous use (measured from
when this option is selected or the start of C
display).
• OFF: C enabled with no warning displayed after prolonged use.
• NOT 3D DISP: C disabled.
q OPT AXIS CONTROL
Reposition the lenses to vertically align their optical axes for C photography. A setting of 0 is
recommended in most circumstances; to choose
a different setting, press the selector up or down
and press MENU/OK to select. Positive values raise
the left lens.
Menus
87
Optional Accessories
The camera supports a wide range of accessories from FUJIFILM and other manufacturers.
■ Digital Viewers
■ Audio/Visual
FinePix REAL 3D V1
(sold separately)
TV (available from
third-party suppliers)
■ Computer Related
Audio/visual
output
Technical Notes
88
■ Printing
USB
USB
SD/SDHC
memory card
Computer (available from
third-party suppliers)
SD card slot or card reader
PictBridge-compatible printer
(available from third-party
suppliers)
Printer (available from
third-party suppliers)
Optional Accessories
Accessories from FUJIFILM
The following optional accessories are available from FUJIFILM. For the latest information on the accessories available in your region, check with your local FUJIFILM representative or visit http://www.fujifilm.
com/products/digital_cameras/index.html.
Rechargeable
Li-ion battery
NP-95 (supplied)
Additional NP-95 high-capacity rechargeable batteries can be purchased as required.
Battery charger
BC-65S
The BC-65S can be used with AC 100 V–240 V, 50/60 Hz
power sources and charges an NP-95 battery in about
210 minutes at +23 °C (+73 °F).
A/V cable
AVC-1
Connect the camera to video devices.
Technical Notes
89
Caring for the Camera
To ensure continued enjoyment of the product, observe the following precautions.
Storage and Use
If the camera will not be used for an extended period, remove the battery and memory card. Do
not store or use the camera in locations that are:
• exposed to rain, steam, or smoke
• very humid or extremely dusty
• exposed to direct sunlight or very high temperatures, such as in a closed vehicle on a sunny day
• extremely cold
• subject to strong vibration
• exposed to strong magnetic fields, such as near
a broadcasting antenna, power line, radar emitter, motor, transformer, or magnet
• in contact with volatile chemicals such as pesticides
• next to rubber or vinyl products
■ Water and Sand
Exposure to water and sand can also damage the
camera and its internal circuitry and mechanisms.
When using the camera at the beach or seaside,
avoid exposing the camera to water or sand. Do
not place the camera on a wet surface.
90
■ Condensation
Sudden increases in temperature, such as occur
when entering a heated building on a cold day,
can cause condensation inside the camera. If this
occurs, turn the camera off and wait an hour before turning it on again. If condensation forms on
the memory card, remove the card and wait for
the condensation to dissipate.
Cleaning
Use a blower to remove dust from the lens and
monitor, then gently wipe with a soft, dry cloth.
Any remaining stains can be removed by wiping
gently with a piece of FUJIFILM lens-cleaning paper to which a small amount of lens-cleaning fluid
has been applied. Care should be taken to avoid
scratching the lens or monitor. The camera body
can be cleaned with a soft, dry cloth. Do not use
alcohol, thinner, or other volatile chemicals.
Traveling
Keep the camera in your carry-on baggage.
Checked baggage may suffer violent shocks that
could damage the camera.
Troubleshooting
Power and Battery
Problem
The camera does
not turn on.
Power
supply
The battery runs
down quickly.
Charging does
not start.
Charging
Charging is slow.
batteries
The indicator
lamp lights, but
the battery does
not charge.
Troubleshooting
The camera turns
off suddenly.
Possible cause
Solution
Page
The battery is exhausted.
Insert a fresh or fully-charged spare battery.
4
The battery is not in the correct orientation. Re-insert the battery in the correct orientation. 4
The battery-chamber cover is not latched. Latch the battery-chamber cover.
5
The AC power adapter is not connected Make sure that the AC power adapter is prop6
properly.
erly connected.
Warm the battery by placing it in a pocket or
The battery is cold.
other warm place and re-insert it in the camera v
immediately before taking a picture.
There is dirt on the battery terminals.
Clean the terminals with a soft, dry cloth.
—
The battery has reached the end of its charging
The battery has been charged many times.
—
life. Purchase a new battery.
p QUICK AF is selected for S POWER Select n POWER SAVE to reduce the drain on
67
MANAGEMENT.
the battery.
The battery is exhausted.
Insert a fresh or fully-charged spare battery.
4
The AC power adapter has been disconReconnect the AC power adapter.
6
nected.
The battery is not correctly inserted.
Re-insert the battery in the camera.
—
The battery is not in the correct orientation. Re-insert the battery in the correct orientation. 4
The AC power adapter is not correctly Plug the adapter correctly into the power out6
plugged into a power outlet.
let.
The temperature is low.
Charge the battery at room temperature.
—
There is dirt on the battery terminals.
Clean the terminals with a soft, dry cloth.
—
The battery has reached the end of its charging
The battery has been charged many times. life. Purchase a new battery. If the battery still 108
fails to charge, contact your FUJIFILM dealer.
91
Troubleshooting
Menus and Displays
Problem
Possible cause
Solution
Menus and displays are not English is not selected for the L a
Select ENGLISH.
in English.
option in the setup menu.
Page
80
C/D
Problem
Possible cause
Solution
C is not selected when NOT 3D DISP is selected for r 3D CAUSelect OFF or ON.
the 3D button is pressed.
TION DISP .
Page
87
Shooting
Problem
Possible cause
Solution
Page
Memory is full.
Insert a new memory card or delete pictures. 7, 39
Format the memory card or internal memory. 85
Memory is not formatted.
No picture is taken
There is dirt on the memory card contacts. Clean the contacts with a soft, dry cloth.
—
when the shutter
The memory card is damaged.
Insert a new memory card.
7
button is pressed.
Taking
The battery is exhausted.
Insert a fresh or fully-charged spare battery.
4
pictures
The camera has turned off automatically. Turn the camera on.
10
The monitor
The monitor may darken while the flash
23
goes dark after
The flash has fired.
charges. Wait for the flash to charge.
shooting.
The subject is close to the camera.
Select macro mode.
22
The camera does
Focus
The subject is far away from the camera.
Cancel macro mode.
not focus.
The subject is not suited to autofocus.
Use focus lock.
20
Macro mode is
Macro mode is not available in the current
Close-ups
Choose a different shooting mode.
27
not available.
shooting mode.
92
Troubleshooting
Problem
The flash does
not fire.
Flash
Flash mode not
available.
The flash does
not fully light the
subject.
Face detection
not available.
Wrong subject
selected.
Page
The subject is not in range of the flash.
Position the subject in range of the flash.
106
The flash window is obstructed.
Hold the camera correctly.
15
Intelligent Face Detection is not available in
Choose a different shooting mode.
the current shooting mode.
The subject’s face is obscured by sunglassRemove the obstructions.
es, a hat, long hair, or other objects.
The subject’s face occupies only a small Change the composition so that the subject’s
area of the frame.
face occupies a larger area of the frame.
The subject’s head is at an angle or the sub- Ask the subject to face the camera and hold
ject is not facing the camera.
their head straight.
The camera is tilted.
Hold the camera straight.
The subject’s face is poorly lit.
Shoot in bright light.
The selected subject is closer to the center Recompose the picture or turn face detection
of the frame than the main subject.
off and frame the picture using focus lock.
27
16
4
65
23
27
16
27
—
15
—
Troubleshooting
Intelligent
No face is
Face
detected.
Detection
Possible cause
Solution
The flash is not available in the current
Choose a different shooting mode.
shooting mode.
The camera is in silent mode.
Turn silent mode off.
The battery is exhausted.
Insert a fresh or fully-charged spare battery.
An option other than OFF is selected for
Turn R CONTINUOUS off.
R CONTINUOUS.
The flash is off (P).
Choose a different flash mode.
The desired flash mode is not available in
Choose a different shooting mode.
the current shooting mode.
The camera is in silent mode.
Turn silent mode off.
20
93
Troubleshooting
Problem
Possible cause
Solution
Page
The lens is dirty.
Clean the lens.
90
The lens is blocked.
Keep objects away from the lens.
15
Pictures are
s is displayed during shooting and the
blurred.
Check focus before shooting.
98
focus frame is displayed in red.
Problem
Use the flash or a tripod.
23
k is displayed during shooting.
images
Pictures are
Slow shutter speed selected when ambient This is characteristic of CCD image sensors
29
mottled.
temperature is high.
and does not indicate a malfunction.
Vertical lines
The camera has been used continuously at Turn the camera off and wait for it to cool
—
appear in pictures. high temperatures.
down.
Turn the camera off before connecting the
Pictures are not
AC power adapter. Leaving the camera on
—
Recording
Power was interrupted during shooting.
can result in corrupted files or damage to the
recorded.
memory card or internal memory.
94
Troubleshooting
Playback
Problem
Possible cause
Solution
Page
The pictures were taken with a different make
Pictures are grainy.
—
—
or model of camera.
Pictures
Playback zoom
The pictures were created using O RESIZE
—
37
unavailable.
or with a different make or model of camera.
Playback volume is too low.
Adjust playback volume.
84
No sound in
Movies
The microphone was obstructed.
Hold the camera correctly during recording. —
movie playback.
The speaker is obstructed.
Hold the camera correctly during playback.
—
Selected pictures Some of the pictures selected for deletion are Remove protection using the device with
Deletion
73
are not deleted. protected.
which it was originally applied.
Troubleshooting
95
Troubleshooting
Connections
Problem
TV
No picture or
sound.
No color.
The computer
Computer does not recognize
the camera.
Pictures can not be
printed.
Only one copy is
PictBridge
printed.
The date is not
printed.
AC power Demo slides are
adapter displayed.
96
Possible cause
Solution
Page
The camera is not properly connected.
Connect the camera correctly.
44
An A/V cable was connected during movie Connect the camera once movie playback
43, 44
playback.
has ended.
Input on the television is set to “TV”.
Set input to “VIDEO”.
—
The camera is not set to the correct video Match the camera Q VIDEO SYSTEM set81
standard.
ting to the TV.
The volume on the television is too low.
Adjust the volume.
—
The camera is not set to the correct video Match the camera Q VIDEO SYSTEM set81
standard.
ting to the TV.
The camera is not properly connected.
Connect the camera correctly.
52–53
The camera is not properly connected.
The printer is off.
Connect the camera correctly.
Turn the printer on.
45
—
The printer is not PictBridge-compatible.
ON is selected for s DEMO MODE.
—
—
Press the shutter button to exit demo and
6, 81
select OFF for s DEMO MODE.
Troubleshooting
Miscellaneous
Problem
Nothing happens
when the shutter
button is pressed.
Possible cause
Temporary camera malfunction.
The battery is exhausted.
The camera does not
Temporary camera malfunction.
function as expected.
No sound.
The camera is in silent mode.
Solution
Remove and reinsert the battery or disconnect
and reconnect the AC power adapter.
Insert a fresh or fully-charged spare battery.
Remove and reinsert the battery or disconnect
and reconnect the AC power adapter. If the
problem persists, contact your FUJIFILM dealer.
Turn silent mode off.
Page
4–5, 6
4
4–5, 6,
108
16
Troubleshooting
97
Warning Messages and Displays
The following warnings are displayed in the monitor:
Warning
B (red)
A (blinks red)
k
Description
The battery is low.
The battery is exhausted.
Slow shutter speed. Picture may be blurred.
s
(displayed in red The camera can not focus.
with red focus frame)
Solution
Insert a fresh or fully-charged spare battery.
Use the flash or mount the camera on a tripod.
• Use focus lock to focus on another subject at the
same distance, then recompose the picture (pg. 20).
• If the subject is poorly lit, try focusing at a distance of
about 2 m (6.6 ft.).
• Use macro mode to focus when taking close-ups.
Aperture or shutter The subject is too bright or too dark. The picIf the subject is dark, use the flash.
speed shown in red ture will be over- or under-exposed.
FOCUS ERROR
Turn the camera off and then on again, taking care not
ZOOM ERROR
Camera malfunction.
to touch the lens. If the message persists, contact a
FUJIFILM dealer (pg. 108).
LENS CONTROL ERROR
No memory card inserted when E COPY is
NO CARD
Insert a memory card.
selected in the playback menu.
The memory card or internal memory is not Format the memory card or internal memory using the
formatted or the memory card was formatted K FORMAT option in the camera setup menu (pg.
in a computer or other device.
85).
CARD NOT INITIALIZED
Clean the contacts with a soft, dry cloth. If the mesThe memory card contacts require cleaning. sage is repeated, format the memory card (pg. 85). If
the message persists, replace the memory card.
Camera malfunction.
Contact a FUJIFILM dealer (pg. 108).
PROTECTED CARD
The memory card is locked.
Unlock the memory card (pg. 7).
BUSY
The memory card is incorrectly formatted.
Use the camera to format the memory card (pg. 85).
98
Warning Messages and Displays
Warning
CARD ERROR
Description
Solution
The memory card is not formatted for use in
Format the memory card (pg. 85).
the camera.
Clean the contacts with a soft, dry cloth. If the mesThe memory card contacts require cleaning or
sage is repeated, format the memory card (pg. 85). If
the memory card is damaged.
the message persists, replace the memory card.
Incompatible memory card.
Use a compatible memory card.
Camera malfunction.
Contact a FUJIFILM dealer (pg. 108).
Troubleshooting
b MEMORY FULL
The memory card or internal memory is full; Delete pictures or insert a memory card with more free
a MEMORY FULL
space.
INTERNAL MEMORY IS FULL pictures can not be recorded or copied.
INSERT A NEW CARD
Re-insert the memory card or turn the camera off
Memory card error or connection error.
and then on again. If the message persists, contact a
FUJIFILM dealer (pg. 108).
WRITE ERROR
Not enough memory remaining to record ad- Delete pictures or insert a memory card with more free
ditional pictures.
space.
The memory card or internal memory is not
Format the memory card or internal memory (pg. 85).
formatted.
The file is corrupt or was not created with the
The file can not be played back.
camera.
Clean the contacts with a soft, dry cloth. If the mesREAD ERROR
The memory card contacts require cleaning. sage is repeated, format the memory card (pg. 85). If
the message persists, replace the memory card.
Camera malfunction.
Contact a FUJIFILM dealer (pg. 108).
99
Warning Messages and Displays
Warning
FRAME NO. FULL
TOO MANY FRAMES
F CAN NOT EXECUTE
m CAN NOT EXECUTE
PROTECTED FRAME
b NO IMAGE
a NO IMAGE
a CAN NOT CROP
CAN NOT CROP
DPOF FILE ERROR
CAN NOT SET DPOF
F CAN NOT SET DPOF
CAN NOT ROTATE
F CAN NOT ROTATE
100
Description
Solution
Format the memory card and select RENEW for the
B FRAME NO. option in the M SET-UP menu.
The camera has run out of frame numbers (curTake a picture to reset frame numbering to 100-0001,
rent frame number is 999-9999).
then return to the B FRAME NO. menu and select
CONTINUOUS.
Date for which more than 4,999 pictures exist
Choose a different date.
selected in sort-by-date view.
Red-eye removal can not be applied to the se—
lected picture or movie.
An attempt was made to delete or rotate a proRemove protection before deleting or rotating pictures.
tected picture.
The source device selected in the playback
Select a different source.
E COPY menu contains no pictures.
An attempt was made to crop a a picture.
The picture selected for cropping is damaged These pictures can not be cropped.
or was not created with the camera.
The DPOF print order on the current memory Copy the pictures to internal memory and create a new
card contains more than 999 images.
print order.
The picture can not be printed using DPOF.
—
Movies can not be printed using DPOF.
—
The picture can not be rotated.
—
Movies can not be rotated.
—
Warning Messages and Displays
Warning
Description
Solution
PRESS AND HOLD
An attempt was made to choose a flash mode
Exit silent mode before choosing a flash mode or adTHE DISP BUTTON TO or adjust the volume with the camera in silent
justing the volume.
DEACTIVATE SILENT MODE mode.
A connection error occurred while pictures
Confirm that the device is turned on and that the USB
COMMUNICATION ERROR were being printed or copied to a computer or
cable is connected.
other device.
Check printer (see printer manual for details). To resume
PRINTER ERROR
Printer out of paper or ink, or other printer er- printing, turn the printer off and then turn it back on.
ror.
PRINTER ERROR
Check printer (see printer manual for details). If printing
RESUME?
does not resume automatically, press MENU/OK to resume.
Movies and some pictures created with other devices
An attempt was made to print a movie, a pic- can not be printed. If the picture was created with the
CAN NOT BE PRINTED ture not created with the camera, or a picture camera, check the printer manual to confirm that the
in a format not supported by the printer.
printer supports the JFIF-JPEG or Exif-JPEG format. If it
does not, the pictures can not be printed.
Troubleshooting
101
Glossary
3D movie format: FUJIFILM has extended the generic Motion JPEG format to create an AVI movie file format that
supports 3D. 3D movie files have the extension “*.AVI” and can be played back on the camera in 3D with stereo
sound. When viewed in Windows Media Player, only the images recorded with the left lens will be displayed.
Digital zoom: Unlike optical zoom, digital zoom does not increase the amount of visible detail. Instead, details visible using optical zoom are simply enlarged, producing a slightly “grainy” image.
DPOF (Digital Print Order Format): A standard that allows pictures to be printed from “print orders” stored
in internal memory or on a memory card. The information in the order includes the pictures to be
printed and the number of copies of each picture.
EV (Exposure Value): The exposure value is determined by the sensitivity of the image sensor and the amount
of light that enters the camera while the image sensor is exposed. Each time the amount of light doubles, EV
increases by one; each time the amount of light is halved, EV decreases by one. The amount of light entering the
camera can be controlled by adjusting aperture and shutter speed.
Exif Print: A standard that allows information stored with pictures to be used for optimal color reproduction during printing.
JPEG (Joint Photographic Experts Group): A compressed file format for color images. The higher the compression
rate, the greater the loss of information and more noticeable drop in quality when the picture is displayed.
Motion JPEG: An AVI (Audio Video Interleave) format that stores sound and JPEG images in a single file. Motion JPEG
files can be viewed on a computer using Windows Media Player (requires DirectX 8.0 or later).
Appendix
102
Multi-picture format: An image file format that allows multiple images to be stored in a single file. This camera
stores 3D images in multi-picture files with the extension “*.MPO”. In the supplied FinePixViewer software, MPO
files are displayed as two JPEG images.
Glossary
Parallax: Changes in the apparent position and orientation of a subject when viewed from different angles.
Point of convergence: The point where the optical axes of the two lenses intersect and parallax disappears.
Smear: A phenomenon specific to CCDs which causes white streaks to appear when very bright light sources, such
as the sun or reflected sunlight, appear in the frame.
White balance: The human brain automatically adapts to changes in the color of light, with the result that objects
that appear white under one light source still appear white when the color of the light source changes. Digital
cameras can mimic this adjustment by processing images according to the color of the light source. This process
is known as “white balance.”
Appendix
103
Internal Memory/Memory Card Capacity
The following table shows the recording time or number of available frames at different image qualities
(the figures for the number of available frames assume that MPO+JPEG is selected for o 3DREC as
described on page 84; multiply these figures by about 1.5 for MPO-only files and by about 3 for 2D images). All figures are approximate; file size varies with the scene recorded, producing wide variations in
the number of files that can be stored. The number of exposures or length remaining may not diminish
at an even rate.
File size
O4:3
O3:2
FINE NORMAL FINE NORMAL
Size (pixels)
3648 × 2736
3648 × 2432
MPO+JPEG 14.7 MB 7.4 MB 13.1 MB 6.6 MB
MPO
9.8 MB 4.9 MB 8.7 MB 4.4 MB
JPEG
4.9 MB 2.5 MB 4.4 MB 2.2 MB
Internal memory
2
5
3
6
(approx. 42 MB)
512 MB
30
65
35
70
1 GB
65
130
75
140
2 GB
130
260
150
290
4 GB
260
530
300
590
8 GB
530 1070
600 1200
16 GB
1070
2120
1200 2380
P4:3
Q4:3
C movie
D movie
FINE NORMAL FINE NORMAL a
b
a
b
2592 × 1944
2048 × 1536 640 × 480 320 × 240 640 × 480 320 × 240
7.5 MB 3.8 MB 4.7 MB 2.4 MB
5.0 MB 2.5 MB 3.1 MB 1.6 MB
—
2.5 MB 1.3 MB 1.6 MB 0.8 MB
SD card
SDHC card
5
11
8
17
65
130
260
530
1060
2110
120
260
520
1040
2090
4150
100
200
410
830
1680
3330
200
410
810
1630
3270
6500
—
3 min.
7 min.
14 min.
28 min. *
57 min. *
114 min. *
36 sec.
7 min.
14 min.
28 min.
56 min. *
113 min. *
224 min. *
—
7 min.
14 min.
28 min.
56 min. *
113 min. *
224 min. *
* Total length of all movie files. Individual movies can not exceed 2 GB, regardless of capacity of memory card.
104
1 min. 10 sec.
13 min.
27 min.
54 min.
108 min. *
215 min. *
433 min. *
Specifications
System
Model
Effective pixels
CCD
Storage media
File system
Appendix
FinePix REAL 3D W1
10 million
Two 1/2.3 -in. CCDs
• Internal memory (approx. 42 MB)
• SD/SDHC memory cards (see page 7)
Compliant with Design Rule for Camera File System (DCF), Exif 2.2, multi-picture format (MPO), and
Digital Print Order Format (DPOF)
File format
• Still pictures (C): MPO+JPEG or MPO
• Still pictures (D): Exif 2.2 JPEG (compressed)
• Movies (C): Stereo AVI with 2 image channels • Movies (D): Motion JPEG AVI
Image size (pixels)
• O 4 : 3: 3,648 × 2,736
• O 3 : 2: 3,348 × 2,432
• P 4 : 3: 2,592 × 1,944
• Q 4 : 3: 2,048 × 1,536
File size
See page 104
Lens
Two Fujinon 3 × optical zoom lenses, F/3.7 (wide angle) – 4.2 (telephoto)
Focal length
f=6.3 mm–18.9 mm (35-mm format equivalent: 35 mm–105 mm)
Zoom
C/B: Combined optical and digital zoom up to approx. 3.8 × (35-mm format equivalent: 39 mm–149 mm)
A:
3 × optical zoom
D:
3 × optical zoom with up to approx. 5.7 × digital zoom (maximum combined zoom approx. 17.1 ×)
Digital zoom
Approx. 5.7 × (up to 17.1 × when combined with optical zoom)
Aperture
F3.7/F5/F8 (wide angle), F4.2/F5.6/F9 (telephoto)
Focus range (distance from Approx. 60 cm (2.0 ft.)–infinity
front of lens)
Macro (D): Approx. 8 cm–80 cm/0.3 ft.–2.6 ft. (wide angle); 60 cm–3 m/2.0 ft.–9.8 ft. (telephoto)
Quick AF: Approx. 1 m (3.3 ft.)–infinity
Point of convergence (C) Approx. 2 m/6.6 ft. (wide angle); 6.5 m/21.3 ft. (telephoto) (pg. 102)
Recommended shooting
Auto parallax off: Approx. 1.3 m/4.3 ft.–infinity (wide angle; point of convergence at 2 m/6.6 ft.); 4.1 m/13.5 ft.–infinity
distance (C)
(telephoto; point of convergence at 6.5 m/21.3 ft.)
Auto parallax on (as measured by FUJIFILM): Approx. 1 m/3.3 ft.–infinity (wide angle); 2 m/6.6 ft.–infinity (telephoto)
105
Specifications
System
Sensitivity
Metering
Exposure control
Exposure compensation
Scene modes
Standard output sensitivity equivalent to ISO 100, 200, 400, 800, 1600; AUTO
256-segment through-the-lens (TTL) metering; MULTI, SPOT, AVERAGE
Program and aperture-priority autoexposure; manual exposure
–2 EV – +2 EV in increments of 1/3 EV (P and A modes)
C (NATURAL AND FLASH LIGHTING; in C mode, images are recorded at size Q), D (NATURAL LIGHT),
L (PORTRAIT), M (LANDSCAPE), N (SPORT), O (NIGHT), H (NIGHT TRIPOD), Q (SUNSET),
R (SNOW), S (BEACH), F (UNDERWATER), U (PARTY), E (ANTI-BLUR)
Picture stabilization
None
Intelligent Face Detection Available (D only)
Shutter speed
• H: 3 s–1/500 s
• O: 1/8 s–1/500 s
• M: 1/2 s–1/1,000 s
• Other modes: 1/4 s–1/1,000 s
Continuous
• I (C): Up to 2 fps (size Q); max. 40 frames
• I (D): Up to 1 fps; max. 40 frames
• J (D): Up to 3 fps (size Q); max. 40 frames
Focus
• Mode: Single AF
• Autofocus system: Contrast-detect TTL AF
• Focus-area selection (Intelligent Face Detection off ): Center (C/D), auto-area (D)
White balance
Auto; seven manual preset modes for direct sunlight, shade, daylight fluorescent, warm white fluorescent, cool white fluorescent, incandescent, and underwater lighting
Self-timer
Off, 2 sec., 10 sec.
Flash
Auto flash; effective range when sensitivity is set to AUTO is approx. 60 cm–3.7 m/2 ft.–12.1 ft. (wide angle), 60 cm–3.3 m/2 ft.–10.8 ft. (telephoto), or in macro mode (D only) 30 cm–80 cm/1 ft.–2.6 ft. (wide angle),
60 cm–1.6 m/2 ft.–5.2 ft. (telephoto)
Flash modes
Auto, fill flash, off, slow sync (red-eye removal off ); auto with red-eye removal, fill flash with red-eye removal, off, slow sync with red-eye removal (red-eye removal on)
Monitor
2.8-in., 230k-dot color LCD monitor; frame coverage approx. 100%
Movies
Frame size 640 × 480 (memory card only) or 320 × 240 pixels; 30 fps; stereo sound; zoom not available
106
Specifications
System
Shooting options
Playback options
Other options
Input/output terminals
A/V OUT (audio/video output)
Digital input/output
DC IN
C: Auto parallax, power management, framing guide, and frame number memory
D: Intelligent Face Detection with red-eye removal, power management, framing guide, and frame
number memory
C: Parallax adjustment, micro thumbnails, multi-frame playback, sort-by-date, cropping, resize, and
slide show
D: Intelligent Face Detection, red-eye removal, micro thumbnails, multi-frame playback, sort-bydate, cropping, resize, slide show, and image rotation
PictBridge, Exif Print, language selection (Simplified Chinese, Traditional Chinese, Dutch, English,
French, German, Italian, Japanese, Korean, Portuguese, Spanish, and Thai), time difference, silent
mode
8-pin multi-connector for NTSC or PAL output with monaural sound
USB 2.0 High Speed (shares A/V OUT connector); PTP (Picture Transfer Protocol)/MTP (Media Transfer Protocol)
For use exclusively with supplied AC-5VC AC power adapter
Power supply/other
Power supply
NP-95 rechargeable battery; AC-5VC AC power adapter; charges in about 4 hours at +23 °C (73 °F)
Guide to the number of
Battery Type
Number of frames
available frames for battery
NP-95
Approx. 230 frames (C A)
operation
CIPA standard, measured using battery supplied with camera and SD memory card.
Appendix
Note: Number of shots that can be taken with battery varies with battery charge level and will decline at low temperatures.
Camera dimensions (W × H × D) 123.6 mm × 68 mm × 25.6 mm/4.9 in. × 2.7 in. × 1.0 in., excluding projections
Camera weight
Approx. 260 g/9.2 oz., excluding batteries, accessories, and memory cards
Shooting weight
Approx. 300 g/10.6 oz., including batteries and memory card
Operating conditions
Temperature: 0 °C to +40 °C (+32 °F to +104 °F)
Humidity: 80% or less (no condensation)
107
Specifications
NP-95 rechargeable battery
Nominal voltage
Nominal capacity
Operating temperature
Dimensions (W × H × D)
Weight
DC 3.6 V (typ.)
1800 mAh
0 °C – +40 °C/+32 °F – +104 °F
49.5 mm × 35.2 mm × 10.8 mm/1.9 in. × 1.4 in. × 0.4 in.
Approx. 39 g/1.4 oz.
Weight and dimensions vary with the country or region of sale.
Color Television Systems
NTSC (National Television System Committee) is a color television telecasting specification adopted mainly in
the U.S.A., Canada, and Japan. PAL (Phase Alternation by Line) is a color television system adopted mainly in
European countries and China.
Notices
• Specifications subject to change without notice. FUJIFILM shall not be held liable for damages resulting from
errors in this manual.
• Although the monitor is manufactured using advanced high-precision technology, small bright points and
anomalous colors (particularly in the vicinity of text) may appear. This is normal for this type of monitor and
does not indicate a malfunction; images recorded with the camera are unaffected.
• Digital cameras may malfunction when exposed to strong radio interference (e.g., electric fields, static electricity, or line noise).
• Due to the type of lens used, some distortion may occur at the periphery of images. This is normal.
108
FUJIFILM Digital Camera Worldwide Network
Contact your local distributor (see list below) for repairs and technical support. Please present the warranty and purchase receipt when requesting repairs; refer to the warranty card for the conditions of the
warranty. Technical support may not be available for models not handled by the local distributor. The
following information is subject to change without notice.
NORTH AMERICA
Canada
FUJIFILM Canada Inc.
U.S.A.
FUJIFILM U.S.A., Inc.
Technical support
Repair service
Technical support
Repair service
TEL 1-866-818-FUJI (3854) http://www.fujihelp.ca
TEL 1-800-263-5018 http://www.fujihelp.ca
TEL 800-800-3854 digitalinfo@fujifilm.com
TEL 800-659-3854
Technical support & repairs
Technical support & repairs
Technical support & repairs
Technical support & repairs
Technical support & repairs
Technical support & repairs
Technical support & repairs
Technical support
Repair service
Technical support & repairs
Technical support & repairs
Technical support & repairs
Technical support & repairs
Technical support & repairs
TEL +54-11-4836-1000 servtec@imageneinformacion.com.ar
TEL +591 33 44 1129 gciagral@bibosi.scz.entelnet.bo
TEL 0800-12-8600 camarasdigitais@fujifilm.com.br
TEL 56-2-6781200 serviciotecnico@reifschneider.cl
TEL +57 1 338-0299 animex@etb.net.co
TEL 593-72-835526
TEL +593 783 5526 portiz@fujifilm.com.ec
TEL (52-55) 5263-55000 eizquierdo@fujifilm.com.mx
TEL (52-55) 5366-5150/56/57 cpalma@fujifilm.com.mx
TEL +595 21 444256 jmarbulo@fujifilm.com.py
TEL +51 14 33 5563 jalvarado@fujifilm.com.pe
TEL +598-2-9002004 fotocam@adinet.com.uy
TEL (05982) 419 4542 kiel@fujifilm.com.uy
TEL 0212-2022300 hellmund@hellmund.com
Technical support & repairs
Technical support & repairs
Technical support
Repair service
TEL 0043 1 6162606/51 or 52 kamera.service@fujifilm.at
TEL 3210242090 info@fuji.be
TEL 38512319060 dsaravanja@fujifilm.hr
TEL 38512316228 info@fujifilm.hr
CENTRAL AND SOUTH AMERICA
Argentina
Bolivia
Brazil
Chile
Colombia
Ecuador
Mexico
Paraguay
Peru
Uruguay
Errece S.R.L.
Procesos de Color S.A.
Fotocamara S.R.L.
Kiel S.A.
C. Hellmund & Cia Sa
EUROPE
Austria
Belgium
Croatia
Fuji Film Oesterreich
Belgian Fuji Agency
I&I d.o.o.
Appendix
Venezuela
Imagen e informacion S.A.
Reifschneider Bolivia Ltda.
FUJIFILM do Brasil Ltda.
Reifschneider SA
Animex de Colombia Ltda.
Espacri Cia Ltda
Importaciones Espacri Cia. Ltda.
Fujifilm de Mexico, S.A. de C.V.
109
EUROPE
Cyprus
Czech Republic
Denmark
Finland
France
Germany
Greece
Hungary
Iceland
Italy
Lithuania
Malta
Norway
Poland
Portugal
Romania
Russia
Slovakia
Spain
110
PMS IMAGING LTD
Doros Neophytou
CAMERA REPAIRS
Fujifilm Cz., s.r.o.
AWH servis
Fujifilm Danmark A/S
Fuji Finland Oy
FUJIFILM France
FUJIFILM Electronic Imaging Europe
GmbH
Technical support & repairs TEL 35722746746 mariosashiotis@fujifilm.com.cy
Technical support & repairs TEL 35722314719 dorosn@logosnet.cy.net
FUJIFILM HELLAS S.A.
Fujifilm Hungary Ltd.
Technical support & repairs
Technical support
Repair service
Technical support & repairs
Call center
Repair service
Technical support & repairs
Technical support & repairs
Technical support
Technical support
Repair service
Technical support & repairs
Technical support & repairs
Technical support & repairs
Technical support & repairs
TEL 00420 234 703 411 petr.barta@fujifilm.cz
TEL 00420 222 721 525 awh@awh.cz
TEL 0045 45662244 fujifilm@fujifilm.dk
TEL +358 9 825951 www.fuji.fi fuji@fuji.fi
direction.technique@pm2s.fr
Tel 0180 / 589 89 80* service@fujifilm-digital.com
*
0,14 EUR pro Minute aus dem deutschen Festnetz, abweichende
Preise aus Mobilfunknetzen möglich,Stand bei Drucklegung.
TEL 0030 210 9404100 fujifilm@fujifilm.gr
TEL 3612389410 fujifilm@fujifilm.hu
TEL 3613633777
Icephoto (Ljosmyndavorur)
TEL 354 568 0450 framkollun@fujifilm.is
FujiFilm Italia S.r.l.
TEL 039-0267978181 info@fujifilm.it
TEL 039-6058294 FAX 039-6058295
Fujifilm Lithuania
TEL 370-5-2130121 info@fujifilm.lt
Ciancio (1913) Co.Ltd.
TEL 0356-21-480500 info@fujifilm.com.mt
Fujifilm Norge AS
TEL 0047-02273
http://www.fujifilm.no/ mailto:post@fujifilm.no
Repair service
TEL 0047-55393880
http://www.camera.no/mailto:service@camera.no
Fujifilm Polska Distribution Sp.
Technical support
TEL +48-22-517-66-00 fujifilm@fujifilm.pl
z o.o.
Repair service
TEL +48-22-886-94-40 serwis@fujifilm.pl
Fujifilm Portugal, Lda
Technical support
TEL (351) 226 194 237 finepix@fujifilm.pt
Repair service
TEL (351) 226 194 200 cameras@fujifilm.pt
CTS-Cardinal Top Systems Ltd
Technical support & repairs TEL 4021-230-09-82 cts_tirla@hotmail.com
Fujifilm Electronic Imaging Europe Technical support & repairs TEL 8 800 200 3854 (Для бесплатных звонков из России)
*
Для звонков из других стран набирайте +7 800 200 3854
GmbH
http://www.fujifilm-digital.ru/ info@fujifilm-digital.ru
Fujifilm Slovakia s.r.o.
Technical support
TEL 00421 2 33 595 107 fujifilm@fujifilm.sk
Repair service
TEL 00421 2 33 595 119 servis@fujifilm.sk
Fujifilm España S.A.
Technical support & repairs TEL 902012535
http://www.fujifilm.es/soporte/ tallersat@fujifilm.es
EUROPE
Sweden
Fujifilm Sverige AB
Switzerland /
Liechtenstein
The Netherlands
Fujifilm (Switzerland) AG
Turkey
FUJIFILM Electronic Imaging
Nederland
Fujifilm Turkiye Sinfo A.S.
U.K.
FUJIFILM UK Ltd.
Ukraine
Image Ukraine CJSC
Technical support
TEL 46 8 506 141 45 kamera@fujifilm.se
Repair service
TEL 46 8 506 141 00 kameraverkstaden@fujifilm.se
Technical support & repairs TEL +41 44 855 5154 RepairCenter@fujifilm.ch
Technical support
Repair service
Technical support
Repair service
Technical support
Repair service
Technical support & repairs
TEL +31(0)102812500 helpdesk@fujifilm-digital.nl
TEL +31(0)102812520 camerareparaties@fujifilm-digital.nl
TEL +90 212 696 5090 csarp@fujifilm.com.tr
TEL +90 212 696 5090 servis@fujifilm.com.tr
TEL +44 (0)8700 841310 fujitec@fuji.co.uk
TEL +44 (0)8700 841314 fujitec@fuji.co.uk
TEL +380-44-4909075 d@fujifilm.ua
Technical support & repairs
Technical support
Repair service
Technical support & repairs
TEL (+98-21)2254810-19 fuka@neda.net
TEL (+) 972 3 9250666 digital@fujifilm.co.il
TEL (+) 972 3 9250666 khaim@shimone.com
TEL 009626-4646387 gstores@go.com.jo
Technical support & repairs
Technical support
Technical support
Technical support
Repair service
Technical support & repairs
Technical support
Repair service
TEL +961 1 252474 fototek@antakiholding.com
TEL 00974 44 66 175 prabu@techno-blue.com
TEL 96626978756 service@fujifilm.com.sa
TEL + 963 11 2218049 f.t.c@Net.SY
TEL + 963 21 4641903 filmtradin@Net.SY
TEL + 971-4-2823700 photography@grandstores.ae
TEL 00967-1-503980
TEL 00967-1-503977
MIDDLE EAST
Iran
Israel
Tehran Fuka Co.
Shimone Group Ltd.
Jordan
Lebanon
Qatar
Saudi Arabia
Syria
Grand Stores Al- Abdali,
Amman / Jordan
Fototek S.A.R.L.
Techno Blue
Emam Distribution Co. Ltd.
Film Trading Company
U.A.E.
Yemen
Grand Stores
Al-Haidary Trading
AFRICA
Foto Express Egypt
Fuji Kenya Ltd
Cameratek CC.
Technical support & repairs TEL (202) 7762062 fotoegypt@access.com.eg
Repair service
TEL (254-20)4446265-8 info@fujifilm.co.ke
Technical support & repairs TEL +27 11 251 2400 www.cameratek.co.za
FUJIFILM Australia Pty Ltd
Brijlal & Co. Ltd
Phocidis SARL
Technical support & repairs TEL 1800 226 355 digital@fujifilm.com.au
Technical support & repairs TEL (679)3304133 kapadia@connect.com.fj
Technical support & repairs TEL (00 687) 25-46-35 phocidis@phocidis.nc
OCEANIA
Australia
Fiji
New Caledonia
Appendix
Egypt
Kenya
South Africa
111
OCEANIA
New Zealand
Papua New
Guinea
Fujifilm NZ Ltd
Oceania PNG Limited
Technical support & repairs TEL +64-9-4140400 glenn.beaumont@fujifilm.co.nz
Technical support
TEL +675 3256411 oceania@daltron.com.pg
Fuji Photo Products Co., Ltd.
PT. Modern Internasional, Tbk.
FUJIFILM (Malaysia) Sdn. Bhd.
Technical support & repairs
Technical support & repairs
Technical support
Repair service
Technical support
ASIA
Hong Kong
Indonesia
Malaysia
Philippines
Singapore
South Korea
Taiwan
Thailand
Vietnam
112
TEL (852)2406 3287 rsd@chinahkphoto.com.hk
TEL +62 021 45867187 assd_kmrsrv@modernphoto.co.id
TEL 603-55698388 technical@fujifilm.com.my
TEL 603-55698388 camera@fujifilm.com.my
YKL Development & Trdg. Corp.
TEL 632-7436601~06
info@yklcolor.com digital@yklcolor.com
Repair service
TEL 632-7436601~06 techop_services@yklcolor.com
FUJIFILM (Singapore) Pte Ltd
Technical support & repairs TEL 65-6380 5557 service@fujifilm.com.sg
Korea Fujifilm Co., Ltd.
Technical support
TEL +82-2-3282-7363 photo@fujifilm.co.kr
Yonsan AS Center (Fujidigital)
Repair service
TEL +82-2-701-1472 1bowl@hanmail.net
Kangnam AS Center (Digitalgallery) Repair service
TEL +82-2-2203-1472 nurijili@hanmail.net
Busan AS Center (Digital-Sewon)
Repair service
TEL +82-51-806-1472 merahan@yahoo.co.kr
Hung Chong Corp.
Technical support & repairs TEL 886-2-6602-8988 dah@mail.hungchong.com.tw
FUJIFILM (Thailand) Ltd.
Technical support
TEL +662-2706000 ext. 751,752
Dusit_Suriyong@fujifilm.co.th yaowarat@fujifilm.co.th
Repair service
TEL +662-2706000 ext.761,762 warin@fujifilm.co.th
International Minh Viet Co., Ltd.
Technical support & repairs TEL +84-8-4135740 ext. 322 diep.phanthithanh@imv.com.vn
Memo
113
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN
http://www.fujifilm.com/products/digital_cameras/index.html