Owner`s manual | FujiFilm S1000fd Digital Camera User Manual

Getting Ready
Using the Camera
Advanced Features
• Photography
• Playback
OWNER’S MANUAL
This manual will show you how to use
your FUJIFILM DIGITAL CAMERA
FinePix S1000fd correctly.
Please follow the instructions carefully.
• Movie
Settings
Camera Connection
Software
Installation
Appendices
Troubleshooting
BL00731-200(1)
Warning
To prevent fire or shock hazard, do not expose the unit to rain
or moisture.
For customers in Canada
For customers in the U.S.A.
This Class B digital apparatus complies with Canadian ICES-003.
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
CAUTION
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for
help.
You are cautioned that any changes or modifications not expressly
approved in this manual could void the user’s authority to operate
the equipment.
Notes on the Grant:
To comply with Part 15 of the FCC Rules, this product must be used
with a Fujifilm-specified ferrite-core A/V cable, USB cable, and DC
supply cord.
2
CAUTION
Please read the Safety Notes (separate note “Notes
and Cautions”) and make sure you understand them
before using the camera.
IMPORTANT
NOTICE
BEFORE OPENING THE CD-ROM PROVIDED BY FUJIFILM
Corporation, PLEASE READ THIS END USER LICENSE AGREEMENT
CAREFULLY. ONLY IF YOU AGREE WITH THIS AGREEMENT,
SHOULD YOU USE THE SOFTWARE RECORDED ON THE CD-ROM.
BY OPENING THE PACKAGE, YOU ACCEPT AND AGREE TO BE
BOUND BY THIS AGREEMENT.
End User License Agreement
This End User License Agreement (“Agreement”) is an agreement between
FUJIFILM Corporation (“FUJIFILM”) and you, which sets forth the terms
and conditions of the license granted for you to use the software provided
by FUJIFILM.
The CD-ROM contains third party software. In case a separate agreement
is provided by a third party supplier for its software, the provisions of such
separate agreement shall apply to the use of such third party software,
prevailing over those of this Agreement.
1. Definitions.
(a) “Media” means the CD-ROM titled “Software for FinePix”- which is
provided to you together with this Agreement.
(b) “Software” means the software which is recorded on Media.
(c) “Documentation” means the operation manuals of Software and
other related written materials which are provided to you together
with Media.
(d) “Product” means Media (including Software) and Documentation
collectively.
2. Use of Software.
FUJIFILM grants to you a nontransferable, nonexclusive license:
(a) to install one copy of Software onto one computer in binary machine
executable form;
(b) to use Software on the computer onto which Software is installed; and
(c) to make one backup copy of Software.
3. Restrictions.
3.1 You shall not distribute, rent, lease or otherwise transfer all or any
part of Software, Media or Documentation to any third party without
FUJIFILM’s prior written consent. You also shall not sublicense,
assign or otherwise transfer all or any part of the rights granted to
you by FUJIFILM under this Agreement without FUJIFILM’s prior
written consent.
3.2 Except as expressly granted by FUJIFILM hereunder, you shall not
copy or reproduce all or any part of Software or Documentation.
3.3 You shall not modify, adapt or translate Software or Documentation.
You also shall not alter or remove copyright and other proprietary
notices that appear on or in Software or Documentation.
3.4 You shall not, or shall not have any third party, reverse-engineer,
decompile, or disassemble Software.
Be sure to read this page before using the software.
4. Ownership.
All copyrights and other proprietary rights to Software and Documentation are
owned and retained by FUJIFILM or the third party suppliers as indicated on
or in Software or Documentation. Nothing contained herein shall be
construed, expressly or implicitly, as transferring or granting any right, license,
or title to you other than those explicitly granted under this Agreement.
5. Limited Warranty.
FUJIFILM warrants to you that Media is free from any defect in material
and workmanship under normal use for ninety (90) days from the date
of your receipt of Media. Should Media not meet the foregoing warranty,
FUJIFILM shall replace such defective Media with other Media bearing
no defect. FUJIFILM’s entire liability and your sole and exclusive
remedy with regard to any defect in Media shall be expressly limited to
such FUJIFILM’s replacement of Media as provided herein
6. DISCLAIMER OF WARRANTY.
EXCEPT AS PROVIDED IN SECTION 5 HEREIN, FUJIFILM PROVIDES
PRODUCT “AS IS” AND WITHOUT WARRANTIES OF ANY KIND,
EXPRESS OR IMPLIED. FUJIFILM SHALL MAKE NO WARRANTY,
EXPRESS, IMPLIED OR STATUTORY, AS TO ANY OTHER MATTERS,
INCLUDING, BUT NOT LIMITED TO NON-INFRINGEMENT OF ANY
COPYRIGHT, PATENT, TRADE SECRET, OR ANY OTHER
PROPRIETARY RIGHTS OF ANY THIRD PARTY, MERCHANTABILITY,
OR FITNESS FOR ANY PARTICULAR PURPOSE.
7. LIMITATION OF LIABILITY.
IN NO EVENT SHALL FUJIFILM HAVE ANY LIABILITY FOR ANY
GENERAL, SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL,
INCIDENTAL, OR OTHER DAMAGES (INCLUDING DAMAGES FOR
LOSS OF PROFITS OR LOST SAVINGS) INCURRED FROM THE
USE OF OR INABILITY TO USE PRODUCT EVEN IF FUJIFILM HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
8. No export.
You acknowledge that neither Software nor any part thereof, will be
transferred, or exported to any country or used in any manner in violation
of any export control laws and regulations to which Software is subject.
9. Termination.
In case you breach any of the terms and conditions hereof, FUJIFILM
may immediately terminate this Agreement without any notice.
10. Term.
This Agreement is effective until the date when you cease to use
Software, unless earlier terminated in accordance with Section 9 hereof.
11. Obligation upon termination.
Upon termination or expiration of this Agreement, you shall, at your own
responsibility and expense, delete or destroy immediately all Software
(including its copies), Media and Documentation.
12. Governing Law.
This Agreement shall be governed by and construed in accordance with
laws of Japan.
3
EC Declaration of Conformity
We
Name:
Address:
FUJIFILM Electronic Imaging Europe GmbH
Benzstrasse 2
47533 Kleve, Germany
declare that the product
Product Name:
FUJIFILM DIGITAL CAMERA FinePix S1000fd
Manufacturer’s Name:
FUJIFILM Corporation
Manufacturer’s Address: 7-3, AKASAKA 9-CHOME, MINATO-KU,
TOKYO 107-0052, JAPAN
conforms to the following Standards:
Safety: EN60065: 2002 + A1
EMC: EN55022: 1998 + A1: 2000 + A2: 2003 Class B
EN55024: 1998 + A1: 2001 + A2: 2003
EN61000-3-2: 2000 + A2: 2005
EN61000-3-3: 1995 + A1: 2001 + A2: 2003
following the provision of the EMC Directive (2004/108/EC) and Low Voltage Directive (2006/95/EC).
Kleve, Germany
February 1, 2008
Place
Date
Signature/Managing Director
This product comes with batteries. When these are empty, you shouldn’t throw them
away but deliver them as domestic chemical refuse.
4
Disposal of Electric and Electronic Equipment in Private Households
Disposal of used Electrical & Electronic Equipment (Applicable in the European Union and other European countries with
separate collection systems)
This symbol on the product, or in the manual and in the warranty, and/or on its packaging indicates that this
product shall not be treated as household waste.
Instead it should be taken to an applicable collection point for the recycling of electrical and electronic
equipment.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences to
the environment and human health, which could otherwise be caused by inappropriate waste handling of this
product.
If your equipment contains easy removable batteries or accumulators please dispose these separately according to your local
requirements.
The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product,
please contact your local city office, your household waste disposal service or the shop where you have purchased the product.
In Countries outside the EU:
If you wish to discard this product, please contact your local authorities and ask for the correct way of disposal.
5
Contents
Warning................................................................. 2
IMPORTANT ......................................................... 3
EC Declaration of Conformity................................ 4
Disposal of Electric and Electronic Equipment in
Private Households ......................................... 5
Contents................................................................ 6
About this Manual ................................................. 9
Accessories Included .......................................... 10
Camera Parts and Features................................ 11
Example of screen Text Display.......................... 13
Getting Ready
Attaching the Strap and Lens Cap ...................... 14
Loading the Batteries .......................................... 15
Checking the battery charge ....................... 17
Loading the Memory Card................................... 18
Turning On and Off ............................................. 21
Setting the language, date, and time .......... 22
Correcting the Date and Time ............................. 24
Selecting the Language ...................................... 25
Using the Camera
Taking Pictures (B AUTO Mode) ................. 26
Using Intelligent Face Detection when
taking pictures .......................................... 29
Taking pictures with the focus and
exposure locked ....................................... 31
AF-assist illuminator.................................... 33
Using zoom function ................................... 34
Adjusting the shot composition ................... 34
Viewing the Images............................................. 36
6
Erasing the Images/Movies .......................... 41
Using the erase button ( /n)................... 41
Erasing the images using
[PLAYBACK MENU] ................................ 41
Advanced Features — Photography
Using the Shooting Functions —
Procedure of Setting .....................................
Setting the Shooting Mode .................................
[B AUTO] ............................................
[
NATURAL LIGHT] ..............................
[
,
SCENE POSITION]...................
[
PANORAMA] .................................
[N PROGRAM AE].....................................
[M SHUTTER PRIORITY AE] ....................
[< APERTURE PRIORITY AE] .................
[> MANUAL]..............................................
Adjusting the Image Brightness
(D Exposure Compensation) .......................
e Macro/> Super Macro (Close-up) ................
d Setting the Flash.............................................
* Self-Timer ......................................................
Setting self-timer ........................................
Taking pictures using self-timer .................
f Taking pictures continuously.........................
j Increasing LCD Monitor Brightness ..............
Using [p-MODE MENU] (Photography)/
[SHOOTING MENU] .....................................
Setting the [p-MODE MENU]
(Photography)..........................................
Setting the [SHOOTING MENU] ................
44
48
48
48
49
53
54
55
57
59
61
63
64
67
67
67
69
73
74
74
74
[p-MODE MENU] (Photography) ....................... 77
Changing the sensitivity setting
([S ISO]) ................................................. 77
Changing the quality setting
([ QUALITY]) ........................................ 78
Changing the FinePix COLOR setting
([ FinePix COLOR]) .............................. 79
[SHOOTING MENU] ........................................... 80
Selecting light metering method
([ PHOTOMETRY]) .............................. 80
Adjusting color balance
([T WHITE BALANCE]) ......................... 81
Focusing the shot quickly
([ HIGH-SPEED SHOOTING]) ............. 82
Specifying the focusing mode
([H FOCUSING]) .................................... 83
Specifying the focusing area
([ AF MODE]) ....................................... 84
Adjust the image outline (hard/soft)
([G SHARPNESS]) ................................ 86
Adjust the amount of light emitted by the flash
([
FLASH] (Brightness Adjustment)) .... 87
Photograph the same image with different
exposure ([
BRACKETING]) ................ 87
Advanced Features — Playback
Playback Information.......................................... 89
Using [p-MODE MENU] (Playback)/
[PLAYBACK MENU] ..................................... 90
Setting the [p-MODE MENU]
(Playback) ............................................... 90
Setting the [PLAYBACK MENU] ................ 90
[p-MODE MENU] (Playback) ............................ 91
Setting automatic playback
([ SLIDE SHOW]) ................................ 91
DPOF set frame
([ PRINT ORDER (DPOF)]) ................. 91
[PLAYBACK MENU]........................................... 96
Correcting red-eye effect in images
([ RED EYE REMOVAL])..................... 96
Rotating the images
([ IMAGE ROTATE])............................ 97
Protecting the images
([ PROTECT]) ...................................... 98
Copying the images
([V COPY]) ............................................ 99
Adding voice memos to the images
([ VOICE MEMO]).............................. 101
Trimming the images
([ TRIMMING])................................... 104
Continued Q
7
Contents
Advanced Features — Movie
r Recording Movies ........................................ 106
Changing movie size................................ 108
w Playing Back Movies ................................... 109
Settings
[U SET-UP]..................................................... 111
Using the [SET-UP] menu......................... 111
[SET-UP] menu option .............................. 112
Camera Connection
Connecting to a TV ........................................... 120
Connecting Camera Directly to Printer —
PictBridge Function ..................................... 121
Software Installation
Installation on a Windows PC ........................... 125
Installation on a Mac OS X ............................... 127
Connecting to a PC ........................................... 130
Using FinePixViewer................................. 133
Appendices
System Expansion Option................................. 134
Accessories Guide ............................................ 135
Using Your Camera Correctly ........................... 136
Discharging rechargeable batteries .................. 137
Notes on the xD-Picture Card™, the SD Memory
Card and the Internal Memory..................... 138
Warning Displays .............................................. 139
8
Troubleshooting
Troubleshooting................................................ 144
Specifications ................................................. 150
Explanation of Terms ..................................... 156
FUJIFILM Digital Camera Worldwide
Network..................................................... 158
Usable Memory Cards
You can use the xD-Picture Card, the SD Memory Card and
the SDHC Memory Card with the FinePix S1000fd. In this
Owner’s Manual, these cards are expressed as “Memory
Card” and “SD Memory Card”.
About this Manual
Z About marks
CAUTION
This mark denotes issues that may affect the camera’s operation.
CHECK
This mark denotes points to notice in the camera’s operation.
MEMO
This mark denotes additional topics that complement the basic operating procedures.
Z Usable Memory Cards
You can use the xD-Picture Card, the SD Memory Card and the SDHC Memory Card with the FinePix S1000fd. In this Owner’s
Manual, these cards are expressed as “Memory Card” and “SD Memory Card”.
Z 4-direction (nopq) button
Up, down, left, and right are indicated by black triangles in the Owner’s Manual. Up or down is shown as n or o, and left or
right is shown as p or q.
When pressing q:
When pressing DISP/BACK:
Z About the illustration for the LCD monitor display
In this manual, the illustration for the LCD monitor display is simplified.
Z Note
In this manual, the menu names or messages displayed in the LCD monitor appear in square brackets([ ]).
9
Accessories Included
• AA-size Alkaline Batteries (LR6) (4)
• CD-ROM (1)
Software for FinePix
• Shoulder strap (1)
• Lens cap (1 set)
• A/V cable (1)
• USB cable (1)
10
• Owner’s Manual (this manual) (1)
• Notes and Cautions (1)
Camera Parts and Features
• Refer to the pages in parentheses for information on using the camera parts or features.
11
Camera Parts and Features
A Strap mount (p.14)
O MENU/OK button
B Zoom lever (p.34) (Multi-frame playback (p.39))
P LCD monitor
C Shutter button
Q DISP (Display)/BACK button (p.34, 36)
D
R D Exposure compensation button (p.61, 89)
Intelligent Face Detection (p.29)/
bRed-eye removal button (p.29)
T Battery cover (p.15)
F ON/OFF switch (p.21)
U Cover lock release catch (p.15)
G Indicator lamp (p.29)
V EVF/LCD (monitor selector) button (p.26)
H Mode dial
W w (Playback) button (p.36)
I AF-assist illuminator (p.33)/Self-timer lamp (p.68)
X p (Photo mode) button (p.74, 77)
J Flash (p.64)
Y nopq (4-direction) button
K dFlash pop-up button (p.64)
Z Terminal cover
L Microphone
! Memory Card slot (p.18)
M Speaker
_ ; USB socket/A/V OUT (Audio/Visual output)
N Viewfinder (EVF)
12
S Tripod mount
E f Continuous button (p.69)
socket (p.120, 121)
Example of screen Text Display
Z Shooting mode
N 16
12/31/2050
SET
1000
12:00 AM
F3.5
A ( Self-timer (p.67)
B e Macro (close-up) (p.63)
C d Flash (p.64)
D
Intelligent Face Detection
(p.29)
E
Photography mode (p.48)
F
Battery level indicator
(p.17)
G 9 White balance (p.81)
H
High-speed shooting
(p.82)
I AF frame (p.27)
J Date/Time (p.22)
K Shutter speed (p.55)
L Aperture (p.57)
M ) Photometry (p.80)
N Sensitivity (p.77)
O
N Quality mode (p.78)
P Number of available frames
(p.154)
Q
FinePix COLOR (p.79)
R {AF warning (p.27)
S
Camera shake warning
(p.139)
T
Increasing monitor
brightness (p.73)
U Y Internal memory (p.20)
V f Continuous shooting
(p.69)
W Exposure compensation
indicator (p.61)
X S Exposure compensation
(p.61)
Z Playback mode
100-0001
12/31/2050
A w Playback mode (p.36)
B
Intelligent Face Detection (p.40)
C
Red-eye removal
D u DPOF (p.91)
E Frame number (p.115)
F
Present (p.36)
G # Voice memo (p.101)
H F Protection (p.98)
12:00 AM
FinePix S1000fd has internal memory that can store images without Memory Card. Y appears on the screen when the internal
memory is active.
13
Attaching the Strap and Lens Cap
Attaching the strap
1
3
Pull the lens cap cord through the strap.
Attach the strap to the strap mounts on the
camera. Once you have attached both ends
of the strap, check carefully to make sure
that the strap is firmly secured.
CAUTION
• Attach the strap correctly to prevent dropping the
camera.
• Attach the lens cap cord to prevent losing the lens cap.
Attaching the lens cap
2
14
Attach the lens cap cord to the lens cap.
Loading the Batteries
1
Slide the lock release catch to open the
battery cover.
Compatible batteries
AA-size alkaline batteries (4) AA-size Ni-MH
rechargeable batteries (4) (sold separately) or AA-size
lithium batteries (4) (sold separately)
Getting Ready
Batteries are required to operate the digital camera. At
first, load the batteries in the camera.
CAUTION
• Never use the following types of
batteries, as they could cause
serious problems such as battery Outer casing
fluid leakage or overheating:
1. Batteries with split or peeling
outer casings
2. Combinations of different
types of batteries or new and
used batteries together
• Do not use manganese or Ni-Cd
batteries.
• Use the same brand and grade
AA-size alkaline batteries as
those supplied with the camera.
• The batteries shall not be exposed to excessive heat
such as sunshine, fire or the like.
CHECK
Check that the camera is turned off before opening the
battery cover.
CAUTION
• Do not open the battery cover while the camera is on.
This could damage the Memory Card or ruin the image
files on the Memory Card.
• Do not apply force to the battery cover.
Continued Q
15
Loading the Batteries
2
Load the batteries correctly as indicated by
the polarity icons.
CAUTION
Match the polarity icons (+ and ,) of the batteries to
those on the inside of the battery cover.
3
Press on the battery cover to push the
batteries down. Slide the cover closed.
CHECK
Make sure to close the battery cover securely until you
hear a click.
16
MEMO
If you want to use the camera powered by AC, the AC
power adapter, AC-5VX (sold separately), and DC
coupler, CP-04 (sold separately), are necessary. Refer to
the manual provided with the AC-5VX and CP-04 for
instructions.
Checking the battery charge
A There is ample battery charge. (Not displayed)
B There is insufficient charge left in the batteries. The
batteries will soon run out. Have a new set of batteries
ready. (Lit red)
C The batteries are depleted. The display will shortly go
blank and the camera will stop working. Replace or
recharge the batteries. (Blinking red)
Getting Ready
Turn the camera on and check the battery charge.
Notes on batteries
• Soil, such as fingermarks on the poles of the batteries,
can shorten time for which the batteries can be used.
• The time for which AA-size alkaline batteries (referred
to hereafter simply as alkaline batteries) can be used
varies depending on the brand. Some brands of alkaline
batteries may stop providing power more quickly than
those supplied with the camera. Note also that due to
their nature, the time for which alkaline batteries can be
used decreases in cold conditions (0°C to +10°C/+32°F
to +50°F). For this reason, it is better to use AA-size NiMH batteries.
• Due to the nature of the battery, the battery level
warning (
, V) may appear early when the
camera is used in cold locations. Try warming the
batteries in your pocket or a similar location before use.
• Depending on the battery type and the level of charge
in the batteries, the camera may run out of power
without first displaying a battery level warning. This is
particularly likely to happen when batteries that have
run out of charge once are re-used.
• Depending on the camera mode, the transition from
to V may occur more quickly.
• Use Fujifilm Battery charger (sold separately) to charge
AA-size Ni-MH batteries.
• When first purchased or if left unused for a long period,
the amount of time which AA-size Ni-MH batteries can
be used may be short.
• Battery power consumption varies greatly depending
on use. When you change to Playback mode from
Shooting mode,
may not occur, however, V
may suddenly blink red and the camera may stop
operation.
• See “Notes and Cautions” (included) for more
information.
17
Loading the Memory Card
Although you can store pictures in the camera’s internal
memory, you can store many more images on the
Memory Card (sold separately). You can use the xDPicture Card and the SD Memory Card with the FinePix
S1000fd. In this Owner’s Manual, these cards are
expressed as “Memory Card”.
2
Insert a Memory Card.
(xD-Picture Card)
SD Memory Cards/SDHC Memory Cards
They are operation-checked at FUJIFILM Corporation.
Manufacturer: SanDisk
MEMO
• Compatible models will be updated in our website:
http://www.fujifilm.com/products/digital_cameras/index.html
• Depending on the SD Memory Card, recording of
movies may be interrupted.
Use of above mentioned SD Memory Cards are
recommended.
• The camera is not compatible with multimedia cards.
1
Align the gold marking with the
gold contact area, then insert an
xD-Picture Card completely.
(SD Memory Card)
Open the battery cover.
Align the gold marking with the
gold contact area, then insert a
SD Memory Card completely.
CAUTION
Do not open the battery cover while the camera is on. This
could damage the Memory Card or ruin the image files on
the Memory Card.
18
CAUTION
Protection
switch
3
Close the battery cover.
Getting Ready
Be sure to unlock the protection of the SD Memory Card
before inserting it. If it is locked, recording/deleting
images, as well as formatting are not available. To unlock
the protection, slide the switch back, and the SD Memory
Card will work normally.
How to replace the Memory Card
CAUTION
• A new SD Memory Card or a card previously used on a
PC or any device other than the camera should be
formatted (➝p.117) on the camera before use.
• Do not use a miniSD adaptor or a microSD adaptor
which have exposed contact areas on the back. Use of
these adaptors may cause a malfunction or damage
due to the improper contacts.
• A miniSD adaptor or microSD adaptor bigger than SD
Memory Card standard size may become stuck. Pulling
out forcefully may cause a malfunction. In that case,
contact your FUJIFILM dealer.
Push the Memory Card into the slot and then slowly remove
your finger. The lock is released and the Memory Card is
pushed out.
Continued Q
19
Loading the Memory Card
CAUTION
• When storing Memory Cards, make sure that they are
kept out of the reach of children. A Memory Card could
be swallowed and cause suffocation. If a child swallows
a Memory Card, seek medical attention or call
emergency number right away.
• If the Memory Cards is oriented incorrectly, it will not go
all the way into the slot. Do not apply force when
inserting a Memory Card.
• Note that the Memory Cards may spring out if you
release your finger quickly from the card immediately
after the lock is released.
• Operation of this camera is only guaranteed when it is
used with FUJIFILM xD-Picture Card and operationchecked SD Memory Card (➝p.18).
• See p.138 for information on the xD-Picture Card, SD
Memory Card and the Internal Memory.
Z About internal memory
FinePix S1000fd has
internal memory that can
store images without
Memory Card. Y appears
on the screen when internal
memory is active.
AUTO
12/ 31
12
31/ 2050
10: 00 AM
10
When a Memory Card (sold separately) is inserted
Record images:
Record images to a Memory Card.
Playback images: Playback images in a Memory Card.
When a Memory Card (sold separately) is not inserted
Record images:
Record images to internal memory.
Playback images: Playback images in internal memory.
MEMO
• The size of an image file varies depending on the
subject. For this reason, the number recorded may not
represent the actual number of frames.
• See p.154 for information on the standard number of
available frames.
20
Z About images in the internal memory
Images held in the camera’s internal memory may be
corrupted or erased due to problems such as camera
faults. Save your important data to another media (i.e.,
DVD-R, CD-R, CD-RW, hard disk, etc.).
It is possible to transfer saved images on the internal
memory to a Memory Card (➝p.99).
Turning On and Off
Slide the ON/OFF switch to turn the camera on in
Shooting mode.
Slide the ON/OFF switch again to turn the camera off.
Turning the camera on in
Playback mode
Press w for about 1 second to turn the camera on in
Playback mode. Slide the ON/OFF switch to turn the
camera off.
Getting Ready
Turning the camera on in
Shooting mode
MEMO
MEMO Switching between the Shooting and
Playback mode
Press the shutter button to switch to the Shooting mode.
Pressing w when the camera is in Shooting mode
switches the camera to the Playback mode. Pressing the
shutter button switches the camera to the Shooting mode.
CAUTION
The ON/OFF switch does not completely disconnect the
camera from its power supply.
21
Turning On and Off
Setting the language, date, and
time
2
Set the date and time.
DATE / TIME NOT SET
When using the camera for the first time after purchasing,
the language, date, and time are cleared. Set the
language, date, and time.
1
2010
2009
YY.MM.DD
2008
2007
2006
[
] screen appears when turning
the camera on.
SET
1. 1
12:00
12 00
AM
NO
A Press p or q to select Year, Month,
Day, Hour, or Minute.
START MENU
/ LANG.
B Press n or o to correct the setting.
SET
NO
MEMO
A Press n, o, p, or q to select the
language.
B Press MENU/OK to confirm the setting.
22
• Holding down n or o changes the numbers
continuously.
• When the time displayed passes “12”, the AM/PM
setting changes.
MEMO
Change the date format.
DATE / TIME NOT SET
DD . MM . YY
MM / DD / YY
12 / 1 / 2008
YY . MM . DD
SET
10:00
AM
NO
A Press p or q to select the date format.
[START MENU] screen also appears when the batteries
have been removed and the camera has been left for a
long period. Once the AC power adapter and DC coupler
has been connected or the batteries have been installed
for 10 hours or more, the camera settings will be retained
for roughly 24 hours even if both sources of power are
removed.
Getting Ready
3
Auto power off function
When the Auto power off function is active, if the camera
is left unused for 2 or 5 minutes, this function turns the
camera off (➝p.118). To turn the camera back on, slide
the ON/OFF switch. To playback images, press w for
about 1 second.
B Press n or o to set the format.
C Always press MENU/OK after the settings
are completed.
Date format
ex. December 1, 2008
[YY.MM.DD]: [2008.12.1]
[MM/DD/YY]: [12/1/2008]
[DD.MM.YY]: [1.12.2008]
23
Correcting the Date and Time
1
2
Open the [SET-UP] menu.
SET - UP
SHOOTING MENU
HIGH-SPEED SHOOTING
SET-UP
Display the [DATE/TIME] screen.
OFF
DATE / TIME
BEEP VOLUME
SHUTTER VOLUME
PLAYBACK VOLUME
LCD BRIGHTNESS
FORMAT
A Press MENU/OK to open the menu.
A Press p or q to select
B Press n or o to select [U SET-UP].
B Press o to move to menu item.
C Press q.
C Press n or o to select [
.
DATE/TIME].
D Press q.
See “2 Set the date and time.” (➝p.22).
24
Selecting the Language
2
Open the [SET-UP] menu.
] screen.
SET - UP
SHOOTING MENU
HIGH-SPEED SHOOTING
SET-UP
Display the [
Getting Ready
1
OFF
AUTO POWER OFF
TIME DIFFERENCE
BACKGROUND COLOR
DISCHARGE
VIDEO SYSTEM
ENGLISH
2 MIN
NTSC
A Press MENU/OK to open the menu.
A Press p or q to select
B Press n or o to select [U SET-UP].
B Press o to move to menu item.
C Press q.
C Press n or o to select [
.
].
D Press q.
See “1 [
] screen appears
when turning the camera on.” (➝p.22).
25
Taking Pictures (B AUTO Mode)
This section describes the basic operations.
1
2
Press the Flash pop-up button to pop-up
the flash.
3
Switch the display.
Turn the camera on.
A Slide the ON/OFF switch.
Press the EVF/LCD to alternate the display between the
viewfinder (EVF) and the LCD monitor.
EVF
B Set the Mode
dial to B.
LCD
CHECK
Select e Macro mode to take close-up shots (➝p.63).
MEMO
The EVF/LCD selection is retained even when the
camera is off or the mode setting is changed.
26
4
Focus on the main subject in the AF frame
and press the shutter button down halfway.
AUTO
12/ 31
12
31/ 2050
10: 00 AM
10
60
AF frame
Halfway
pressed
Do not cover the lens or
flash with your fingers.
F 3.
3 5
Using the Camera
Holding the camera correctly
Brace your elbows against your sides and hold the
camera with both hands.
Using the viewfinder (EVF) allows for a steady arm
position, preventing picture blur.
AF frame
becomes smaller
and camera
focuses on the
subject.
CHECK
CAUTION
• Moving the camera while shooting gives a blurred
picture (camera shake). Hold the camera steadily with
both hands.
• If the lens or flash is obscured by your fingers or the
strap, or if the autofocus ring is touched when shooting,
subjects may be out of focus or the brightness
(exposure) of your shot may be incorrect.
• When the autofocus ring is held during operation, a
warning message [ZOOM ERROR] is displayed. Then
the lens will automatically refocus.
• Focus on the subject
Double beep is heard
Indicator lamp lit green
• Not focus on the subject
No sound
AF frame lit red
{ indicated
Indicator lamp blinking green
MEMO
• The shutter button has a halfway point at which focus
and exposure are automatically optimized before taking
the picture by pressing fully down.
• When pressing the shutter button halfway, a lens
operation sound may be heard.
Continued Q
27
Taking Pictures (B AUTO Mode)
5
Press the shutter button fully.
Double
beep
Flash
Click
When pressing the shutter
button down halfway, b
appears on the screen before
the flash fires.
60
Halfway pressed
Fully pressed
F 3.
3 5
If you want to change the setting, see p.64 for information on
flash.
CAUTION
When taking a picture using the flash, the image may
disappear and go dark briefly due to flash charging. The
indicator lamp blinks orange during charging.
MEMO
• When the subject is not in the AF frame, use AF/AE lock
to take the picture (➝p.32).
• When pressing the shutter button down fully in one
motion, the camera takes the picture without the AF
frame changing.
28
CAUTION
• The image shown on the screen before the picture is
taken may differ in brightness, color, etc. from the
image actually recorded. Play back the recorded image
to check it (➝p.36).
• When selecting a slow shutter speed that will cause
camera shake,
appears on the screen. Use flash or
a tripod.
• See p.139-143 for information on warning displays. See
“Troubleshooting” (➝p.144-149) for more information.
Z Indicator lamp display
The indicator lamp lights or blinks when pressing the shutter
button, etc. The indicator lamp shows the camera status.
Using Intelligent Face Detection
when taking pictures
Indicator lamp
Display
Status
Lit green
Locking the focus
Blinking green
Camera shake warning, AF warning,
or AE warning (ready to shoot)
Blinking green and
orange alternately
Recording to Memory Card or internal
memory (ready to shoot)
Lit orange
Recording to Memory Card or internal
memory (not ready)
Blinking orange
Charging flash (flash will not fire)
Blinking red
• Warnings for Memory Card and
internal memory
Card not formatted, incorrect format,
memory full, Memory Card or
internal memory error
• Lens operation error
MEMO
Detailed warning messages appear on the screen
(➝p.139-143).
1
Using the Camera
Intelligent Face Detection allows you to focus on and
adjust the brightness of people’s faces. Intelligent Face
Detection is effective with the camera held horizontally or
vertically.
Available Shooting modes: B,
,
/
(H, /,
,
,
,
,
,
), N, M, <, >
Set Intelligent Face Detection.
Press
. Intelligent Face Detection setting changes
each time you press
.
OFF
FACE DETECTION
REMOVAL ON
FACE DETECTION
REMOVAL OFF
Red-eye effect, caused by the light of the flash reflecting
off the inside of the eye, will be corrected automatically
when a picture is taken with [
FACE
DETECTIONbREMOVAL ON] set.
Continued Q
29
Taking Pictures (B AUTO Mode)
2
CAUTION
CHECK [
• Correction results may differ depending on the scene.
• The processing may take more time if there are many
faces in an image.
When a picture is taken with [
FACE
DETECTIONbREMOVAL ON] set, the red-eye effect
will be detected and corrected before the image is
recorded.
Check the composition on the LCD monitor.
When there are multiple people
in the frame, Intelligent Face
Detection will set a green frame
around the face nearest to the
center of the picture. This face
has focusing priority.
DETECTING
FACE DETECTIONbREMOVAL ON]
ARed-eye effect in an
image will be detected after
the shooting.
CANCEL
Green frame
3
30
Press the shutter button down fully to take
pictures.
REMOVING
BProcessing will end when
the red-eye effect is not
detected.
Subjects not suitable for Intelligent Face Detection
AUTO
12/ 31
12
31/ 2050
Use AF/AE lock (➝p.31) to guarantee best result
when shooting a subject that is not suited for
Intelligent Face Detection.
CAUTION
• If the camera or subject move as the picture is taken,
the subject’s face may move out of the Intelligent Face
Detection frame.
• When the camera is detecting multiple faces, the green
frame is set around the face near the center. If you want
to focus on another subject, move the camera so that
the new subject is in the center of the screen.
If focus is still not achieved, press
(Intelligent Face
Detection) to turn off the function, and take the picture
using AF/AE lock (➝p.32).
Intelligent Face Detection can focus on a face in a white
frame providing the subjects in the green and white
frame are of the same focal length.
• Pressing the shutter button halfway with Intelligent Face
Detection off, the focus will be on the center of the
frame.
Using the Camera
Intelligent Face Detection automatically focuses on a face(s).
However, difficulties will occur with the Intelligent Face
Detection mode in the following situations:
• The face is obscured by glasses, sunglasses, a hat or hair.
• A person turned sideways, or who has their head tilted
• The subject is too far away to recognize a face
Intelligent Face Detection will not work in cases where the
subject is standing on his/her head, is not a person (pet or
other animal), or if the camera is not held correctly.
Taking pictures with the focus
and exposure locked
10: 00 AM
10
In the above composition, the subjects are not in the AF
frame. Pressing the shutter button halfway at this point
will result in the subjects being out of focus.
AF/AE lock is useful:
Use AF/AE lock to guarantee best result when shooting a
subject that is not suited to autofocusing (➝p.33).
CAUTION
When taking a picture in AF/AE lock, cancel
Intelligent Face Detection.
Continued Q
31
Taking Pictures (B AUTO Mode)
3
Using AF/AE lock
1
Move the camera slightly so that one of the
subjects is in the AF frame.
Continue to hold the shutter button down
halfway. Move the camera back to the
original image and press the shutter button
fully.
Click
AUTO
12/ 31
12
31/ 2050
60
10: 00 AM
10
F 3.
3 5
Fully pressed
2
Press the shutter button down halfway to
focus on the subject.
Double
beep
60
Halfway
pressed
32
F 3.
3 5
MEMO
• AF/AE lock can be applied repeatedly before the shutter
is released.
• On FinePix S1000fd, pressing the shutter button down
halfway locks the focus and exposure settings (AF and
AE lock).
Subjects not suitable for autofocus
Use this illuminator to focus on the subject in dimly lit
conditions.
When pressing the shutter button down halfway, the
camera fires the AF-assist illuminator (orange) while
focusing on your subject.
Using the Camera
FinePix S1000fd uses a high-precision autofocusing
mechanism. However, it may have difficulty focusing on the
following:
AF-assist illuminator
AF-assist
illuminator
Very shiny subjects such
as a mirror or car body
•
•
•
•
•
Fast moving subjects
Subjects photographed through glass
Subjects that do not reflect well, such as hair or fur
Subjects with no substance, such as smoke or flames
Dark subjects
Subjects with little or no contrast between the subject and
the background (such as subjects dressed in the same color
as the background)
• Shots where another high-contrast object (not the subject) is
close to the AF frame and is either closer or further away
than your subject (such as a shot of someone against a
background with strongly contrasting elements)
For such subjects use AF/AE lock (➝p.32).
MEMO
• Even when the AF-assist illuminator fires, the camera
may have difficulty focusing in some conditions.
• Even though there is no danger to safety, do not expose
it directly in someone’s eyes.
• When using the AF-assist illuminator in Macro mode,
the camera may have difficulty focusing to take closeup shots.
• See p.111, 112 for information on turning the AF-assist
illuminator off.
• AF-assist illuminator does not fire in ,, .,
,
,
,
,
, or
mode.
33
Taking Pictures (B AUTO Mode)
Using zoom function
Use the zoom lever to take pictures with zoom function.
The zoom bar appears on the screen while the zoom lever
is being used. Use digital zoom when you want to shoot
the subject closer (➝p.116).
T: tele zoom lever
(zoom in)
AUTO
Adjusting the shot composition
Select the screen display.
Press DISP/BACK to change the screen display.
W: wide zoom lever
(zoom out)
AUTO
N 16
AUTO
zoom bar
12/ 31
12
31/ 2050
10: 00 AM
10
Text displayed
No text displayed
N 16
AUTO
12/ 31
12
31/ 2050
Post shot assist window
displayed
34
10: 00 AM
10
Framing guideline
displayed
Z Format of post shot assist window
Best framing
AUTO
12/ 31
12
31/ 2050
10: 00 AM
10
Using the Camera
Position the main subject at
the intersection of two lines
in this frame or align one of
the horizontal lines with the
horizon. Use this frame as a
guide to the subject’s size
and the balance of the shot
while composing a shot.
MEMO
Always use AF/AE lock when composing a shot. The
image may be out of focus if AF/AE lock is not used.
Post shot assist window
Up to the last 3
photographed images
appear on the post shot
assist window. This serves
as a guide for taking other
shots with similar
compositions.
35
Viewing the Images
Playback your images to check them. For important
photographs, always take a test shot and view the image
to make sure that the camera is working normally.
Select the screen display.
Press DISP/BACK during Playback mode to change the
screen display.
Setting the camera to Playback
mode
Press w during shooting to change to Playback mode.
100- 0001
100
N
When the camera is off, press w for about 1 second to
turn the camera on in Playback mode.
MEMO
• Press w to play back the last shot.
• When playing back images shot with a camera other
than FinePix S1000fd,
a present icon appears on
the screen.
CAUTION Still images viewable on
FinePix S1000fd
This camera will display still images recorded on FinePix
S1000fd or still images (excluding some uncompressed
images) recorded on any FUJIFILM digital camera that
supports xD-Picture Cards or SD Memory Cards. Clear
playback or playback zooming may not be possible for still
images shot on cameras other than FinePix S1000fd.
36
12/ 31
12
31/ 2050
10: 00 AM
10
Text displayed
No text displayed
20501212/2929
12 30
12/30
12/31
12
31
1/11
Sorting by date
Single-frame playback
100-0001
100
0001
Playback zoom
1
Zoom in / Zoom out.
12/ 31
12
31/ 2050
T: tele zoom lever
(zoom in)
10: 00 AM
10
Using the Camera
To zoom in an image during single-frame playback:
W: wide zoom lever
(zoom out)
To select the required image:
Press p: last image
Press q: next image
Zoom bar
Selecting images
To select images on the
thumbnail lists screen, hold
down p or q for 1 second
during playback.
When releasing p or q,
camera returns to singleframe playback.
Turn to T or W to zoom in or out of an
image.
Continued Q
37
Viewing the Images
2
Display another part of the image.
Sorting by date
In sorting by date mode, you can view all images taken on
the same day.
Navigation screen
(Current displayed
image)
Press n, o, p, or q to display another
part of the image.
38
2050
12 / 29
12 / 30
12 / 31
1 / 11
MEMO
A Press n, o, p, or q to move the cursor
(colored frame) to the selecting frame.
• Zoom cannot be performed when the images recorded
by ` are played back.
• Press DISP/BACK to cancel playback zoom.
B Press MENU/OK to enlarge the image.
Selecting the date
2050
Use this function to display a single frame, 2 frames, 9
frames or 100 frames (Micro Thumbnail). You can
compare and select images using the Multi-frame display.
Use the zoom lever to change the display.
100-0001
N
11
A Press n, o, p, or q to move the cursor
(colored frame) to
on the upper left
frame.
12/ 31
12
31/ 2050
Using the Camera
12 / 29
12 / 30
12 / 31
Multi-frame playback
10: 00 AM
10
B Press p to display the selecting date.
C Press n or o to move the cursor (colored
frame) to select the date.
Press n or o repeatedly to jump to the
next page.
D Press q.
Continued Q
39
Viewing the Images
2 frames playback
A Press n, o, p or q to select the
images you want to compare.
Using Intelligent Face Detection
when playing back pictures
You can display and enlarge the faces in images when
playing back the images shot using the Intelligent Face
Detection function (
is displayed) (➝p.29).
B Press MENU/OK to enlarge the image.
9 frames playback/100 frames playback
(Micro thumbnails playback)
A Press n, o, p or q to change the
colored frame and select an image.
Press n or o repeatedly to jump to the
next page.
DETECTED FACES
A Press
, then the frame(s) appears on
the detected face(s) in pictures.
B Press MENU/OK to enlarge the image.
B The detected face(s) is enlarged each time
you press
.
C Press n, o, p, or q to display another
part of the image (➝p.37).
CAUTION
The images recorded by ` cannot be enlarged.
MEMO
Press DISP/BACK to return to normal playback.
40
Erasing the Images/Movies
Use this mode to erase unnecessary images or movies to
have ample free space on the Memory Card or internal
memory. Your camera calls images “frames”.
/n)
(n) erases images easily.
ERASE OK?
OK
PLAYBACK MENU
ERASE
BACK
RED EYE REMOVAL FRAME
IMAGE ROTATE
ALL FRAMES
PROTECT
COPY
VOICE MEMO
CANCEL
A Press MENU/OK to open the [PLAYBACK
MENU].
SET
A Press p or q to select the erasing
image.
B Press
Erasing the images using
[PLAYBACK MENU]
Using the Camera
Using the erase button (
Pressing
Setting the camera to w
Playback mode (➝p.36)
(n).
C Press p or q to select [OK].
D Press MENU/OK to erase the displayed
image.
B Press n or o to select [
ERASE].
C Press q.
D Press n or o to select [FRAME] or [ALL
FRAMES].
E Press MENU/OK to confirm the setting.
Continued Q
41
Erasing
Erasing
the the
Images/Movies
Images/Movies
Erasing one frame at a time ([FRAME])
Setting the camera to w playback mode (➝p.36)
Erasing all frames ([ALL FRAMES])
ERASE OK?
ERASE ALL OK?
IT MAY TAKE A WHILE
OK
YES
CANCEL
A Press p or q to select the erasing frame
(file).
A Press p or q to select [OK].
B Press MENU/OK to erase the currently
displayed frame (file).
B Press MENU/OK to erase all the frames
(files).
MEMO
MEMO
To erase another frame (file), repeat above steps.
When erasing frames (files) is completed, press DISP/
BACK.
Press DISP/BACK to cancel
erasing of all the frames
(files). Some unprotected
frames (files) will be left
unerased.
CAUTION
Pressing MENU/OK repeatedly erases consecutive
frames (files). Take care not to erase a frame (file) by
mistake.
42
CANCEL
SET
CANCEL
Setting the camera to w playback mode (➝p.36)
MEMO
CAUTION
Using the Camera
• When using a Memory Card, the images in the Memory
Card are erased. When not using a Memory Card, the
images in the internal memory are erased.
• Protected frames (files) cannot be erased. Unprotect
the frames (files) before erasing them (➝p.98).
• [DPOF SPECIFIED. ERASE OK?] or [DPOF
SPECIFIED. ERASE ALL OK?] appears, when erasing
DPOF specified files is attempted.
Erased frames (files) cannot be recovered. Back up
important frames (files) onto your PC or another media.
43
Using the Shooting Functions — Procedure of Setting
Specify the camera settings for taking pictures to get the
best result. A general guide is given below.
1
Select the Shooting mode.
Turn the Mode dial to select the Shooting mode.
The camera settings are tailored to the scene being
shot.
CAUTION
When you have been used for long periods in places
subject to extreme temperature rises, it will lower your
image quality and streaking may also be visible in your
images. If this occurs, turn the camera off several times to
prevent heating the camera.
44
B Auto
Natural light
This is the easiest mode for taking
pictures (➝p.48).
This mode produces beautiful images
that retain the natural ambience when
shots are taken in low-light conditions
(➝p.48).
,
Scene position
Use to select the ideal setting from Scene
position menu for the shot. (➝p.49).
PANORAMA
Used for shooting panoramic pictures
(➝p.53).
N Program AE
M Shutterpriority AE
< Aperturepriority AE
Used for changing the aperture or shutter
speed setting so that the action is frozen,
the flow of the motion is conveyed, or the
background is out of focus (➝p.54-58).
> Manual
All manual settings for taking pictures
(➝p.59).
r Movie
Used for shooting movies (➝p.106).
2
Specify the photography settings.
Pressing buttons or selecting menu allows you to
specify photography functions. You can obtain the
best result for shooting.
Z Specifying functions using buttons
D Exposure
compensation
button
Intelligent Face
Detection/
b Red-eye removal
button
f Continuous
button
Used to take a series of continuous shots
or to use auto bracketing (with exposure
compensation) (➝p.69).
Intelligent
Face
Detection/
b Red-eye
removal
Pressing this button allows you to focus
on people’s faces. Also, red-eye effect,
caused by the light of the flash reflecting
off the inside of the eye, can be corrected
before an image is recorded. (➝p.29).
e Macro
Used for close-up shots (➝p.63).
d Flash
Used for shots in dark locations or for
backlit subjects, etc. (➝p.64).
* Self-timer
Used in situations such as group shots
where the photographer is included in the
shot (➝p.67).
D Exposure
Used for changing the image brightness
compensation (➝p.61).
Continued Q
Advanced Features — Photography
e (p)Macro button
d (q)Flash button
* (o)Self-timer
button
f Continuous
45
Using the Shooting Functions — Procedure of Setting
Z Specifying functions using [p-MODE MENU] (p
button)
Press p button to open the [p-MODE MENU].
Z Specifying functions using [SHOOTING MENU]
(MENU/OK button)
SHOOTING MENU
MODE MENU
ISO
QUALITY
COLOR
46
AUTO
N
STD
[S ISO]
Use to specify required sensitivity
setting (➝p.77).
[
QUALITY]
Use to specify required image size
(➝p.78).
[
FinePix COLOR]
Use to specify required color tone
(➝p.79).
PHOTOMETRY
WHITE BALANCE
AUTO
HIGH - SPEED SHOOTING OFF
FOCUSING
AF MODE
STD
SHARPNESS
[
SCENE
POSITION]
Use to select the best setting for the
scene being shot. Choose from 13
types of scene (only
or
)(➝p.49).
[
PHOTOMETRY]
Use to select light metering method
(only N, M, <, >) (➝p.80).
Use to adjust the color tone (only N,
M, <, >) (➝p.81).
[
Use to focus the shot quickly (➝p.82).
HIGH-SPEED
SHOOTING]
[H FOCUSING]
Use to specify focusing mode (only
N, M, <, >) (➝p.83).
[
AF MODE]
Use to specify focusing area (only N,
M, <, >) (➝p.84).
[G SHARPNESS]
Use this setting to soften or
emphasize the outline and quality of
an image (only N, M, <, >) (➝p.86).
[
[
FLASH]
(Brightness
Adjustment)
BRACKETING]
Advanced Features — Photography
[TWHITE
BALANCE]
Use this setting to adjust the amount
of light emitted by the flash to suit the
photography conditions or to achieve
a desired effect (only N, M, <, >)
(➝p.87).
Use this setting to photograph the
same image with different exposure
settings (only N, M, <, >) (➝p.87).
47
Setting the Shooting Mode
You can select the most suitable setting according to the
subject by selecting one of the Shooting modes.
[B AUTO]
This is the easiest mode for providing crisp and clear
shots.
Use this mode for ordinary photography.
Camera specifies all settings other than p-MODE
([QUALITY] and [FinePix COLOR]) automatically.
[
NATURAL LIGHT]
This mode produces beautiful images that retain the
natural ambience when shots are taken in low-light
conditions.
This mode is also ideal for shooting indoor or situations
where the flash cannot be used.
Camera sets the high-sensitivity setting when selecting
the Natural light mode. This mode is effective for reducing
camera shake and moving-subject blurring when taking
pictures in low-light conditions.
Set the Mode dial to
Set the Mode dial to B.
.
CHECK
CHECK
• See p.65 for information on the available flash modes.
• Only [AUTO] can be selected for the [
ISO]
(sensitivity) setting.
48
• Flash cannot be used in the Natural light mode.
• Only [AUTO] can be selected for the [
ISO]
(sensitivity) setting.
[
,
SCENE POSITION]
Z Selecting Scene position setting
This mode provides the best Scene position setting for the
scene being shot. Choose from 13 types of scene.
Select the Scene position setting in the [SCENE
POSITION] menu.
or
Portrait with soft
overall tone and
beautiful skin tones
SET
CANCEL
A Press MENU/OK to open the menu.
About
and
of the Mode Dial
The camera enables to set the scene position for
and
separately.
For example, select H for
and , for
separately at
traveling. The setting combination can be used for variety of
shooting scene. The menu options of
and
are the
same. However the options cannot be set for both
and
.
MEMO
•
•
•
•
•
and
are set to H and , as factory default
settings.
See p.65 for information on the available flash modes.
[
p-CHROME] (➝p.79) cannot be set.
AF-assist illuminator does not fire in ,, .,
,
,
,
,
and
mode.
Only [AUTO] can be selected for the [
ISO]
(sensitivity) setting.
B Press n or o to select [
POSITION].
SCENE
C Press q.
Advanced Features — Photography
Set the Mode dial to
.
PORTRAIT
LANDSCAPE
SPORT
NIGHT
D Press n or o to select the setting.
E Press MENU/OK to confirm the setting.
Continued Q
49
Setting the Shooting Mode
Z Scene position list
Scene position
50
Functions
[H PORTRAIT]
Use this mode for photography to get beautiful skin tones and soft overall tone.
[, LANDSCAPE]
Use this mode for shooting scenery in daylight and provides crisp, clear shots of scenery
such as buildings and mountains.
[. SPORT]
Use this mode to take pictures of a moving subject. It gives priority to faster shutter
speeds. When setting [.SPORT] mode, the camera sets to [ HIGH-SPEED
SHOOTING] mode (➝p.82) automatically.
[/ NIGHT]
Use this mode for shooting evening and night scenes. A picture is taken with a slow
shutter of up to 8 seconds.
[
FIREWORKS]
Use this mode to shoot fireworks. It is effective for taking more vivid shots of fireworks
with a slow shutter. Refer to “Selecting the exposure time setting” (➝p.52).
[
SUNSET]
Use this mode to shoot sunset, making the colors more vivid.
[
SNOW]
Use this mode to prevent darkening images and provide crisp, clear shots, when
shooting at snowy scene where the whole screen appears white.
[
BEACH]
Use this mode to prevent darkening images and provide crisp, clear shots, when
shooting at beach under strong sunlight.
Scene position
Functions
MUSEUM]
[
PARTY]
Use this mode for shooting at indoor wedding and party. This mode produces beautiful
images that retain the natural ambience when shots are taken in low-light conditions.
[
FLOWER]
Use this mode to take clear close-up shots when zooming up a flower. It is effective for
taking more vivid shots of flower petal.
[
TEXT]
Use this mode to shoot documents and white board. It is effective for taking clearer
shots.
[ PICTURE
STABILIZATION]
Used for selecting a fast shutter speed that reduces camera shake and moving-subject
blurring.
CHECK
• When setting [. SPORT] mode, the camera sets to [
HIGH-SPEED SHOOTING] (➝p.82) automatically.
• Use a tripod to prevent camera shake for [/ NIGHT], [
FIREWORKS] and [
PANORAMA], as a slow shutter speed is
used.
• When setting [
FLOWER] or [
TEXT] mode, the camera sets to e Macro mode automatically.
• Check whether photography is permitted before using [
MUSEUM] mode.
Advanced Features — Photography
[
Use this mode for taking pictures in places such as museum where the use of flash and
making an operation sound and a shutter sound are restricted. Flash mode is forcibly set
to Suppressed flash, and operation sound, shutter sound, and self-timer lamp are off.
51
Setting the Shooting Mode
Z Selecting the exposure time setting for [
WORKS]
FIRE
SETTING EXPOSURE TIME
2"
A Press D to open the setting screen.
B Press n or o to select the exposure time.
52
[
PANORAMA]
You can take panoramic pictures by stitching 3 pictures
into a panoramic scene.
A Set the Mode dial to
.
1
2 3
3
2 1
C Take the first picture. Press MENU/OK if you want to
save the first picture.
If the pan direction is left to right, a section from the
right side of the first picture will appear on the left side
of the second picture you will take, so that you can
align the next shot in panoramic fashion.
E If you are only taking two pictures, press n to stitch
them together.
After you take the third picture, press MENU/OK to
stitch the pictures together.
Press MENU/OK again to save the panoramic picture.
Advanced Features — Photography
B You can select the direction of taking panoramic
pictures from left to right or right to left by pressing p
or q.
D Compose the second picture by overlapping the saved
section of the first image onto the matching area in the
viewfinder on the far left side. Then take your second
shot. Press MENU/OK to save the second picture.
Repeat one more time for a panoramic view of the
combined pictures.
MEMO
•
•
•
•
Use a tripod to prevent camera shake.
Only the panoramic picture is saved.
The picture size is set to 3 automatically.
Exposure compensation and white balance are set with
the first picture.
• The flash cannot be used.
53
Setting the Shooting Mode
[N PROGRAM AE]
A Press D to open the setting screen.
This is an automatic mode to specify the settings except
for the shutter speed and aperture setting.
This is a simple way to take pictures the same as the <
Aperture-priority Auto and M Shutter-priority Auto modes
(Program shift).
B Select different shutter speed and aperture
setting combinations without changing the
exposure setting.
Set the Mode dial to N.
C Press the shutter button to take pictures.
MEMO
Shooting functions:
• [ PHOTOMETRY] (➝p.80)
• [T WHITE BALANCE] (➝p.81)
• [H FOCUSING] (➝p.83)
• [ AF MODE] (➝p.84)
• [G SHARPNESS] (➝p.86)
• [ FLASH] (➝p.87)
• [ BRACKETING] (➝p.87)
• Program shift can be used when Suppressed flash
(➝p.65) is set in flash mode.
• The shutter speed and aperture setting appear in yellow
when the camera is in Program shift mode.
• Any of following cancels Program shift:
- Changing the Mode dial setting
- Setting the camera to Playback mode
- Turning the camera off
- Popping the flash up
CHECK
See p.65 for information on the available flash modes.
CAUTION
Z Program shift
ISO 100
ISO 100
SET
60
54
PROGRAM SHIFT
F3. 5
F3
When the brightness of the
subject is outside the camera’s
brightness metering range, [---]
appears as the shutter speed and
aperture setting on the screen.
[M SHUTTER PRIORITY AE]
Z Setting the shutter speed
This is an automatic mode to set the shutter speed.
Use this mode to freeze a moving subject (fast shutter
speed) or convey the impression of movement (slow
shutter speed).
ISO 100
Shutter speed
Set the Mode dial to M.
SETTING SHUTTER SPEED
F3. 5
F3
A Press D to open the setting screen.
Shooting functions:
• [ PHOTOMETRY] (➝p.80)
• [T WHITE BALANCE] (➝p.81)
• [H FOCUSING] (➝p.83)
• [ AF MODE] (➝p.84)
• [G SHARPNESS] (➝p.86)
• [ FLASH] (➝p.87)
• [ BRACKETING] (➝p.87)
B Press n or o to select the shutter speed.
Advanced Features — Photography
1000
C Press the shutter button to take pictures.
CHECK
See p.65 for information on the available flash modes.
Continued Q
55
Setting the Shooting Mode
CAUTION
Shutter speed
ISO 100
F2.8
F2
SET
200
F2. 8
F2
When the correct
exposure cannot be
obtained with selected
shutter speed, the
aperture setting appears
in red. When this occurs,
adjust the shutter speed
again.
When shooting a moving subject, you can either “freeze the
motion” or “capture the sense of movement” by adjusting the
shutter speed.
Fast
Freezes the motion of the
subject.
Slow
Photographs the traces left
by the subject’s movement.
Lit red
ISO 100
SET
50
56
F-----
When the brightness of
the subject is outside the
camera’s brightness
metering range, [F---]
appears as the aperture
setting. When this
occurs, press the shutter
button down halfway to
measure the light level
again.
[< APERTURE PRIORITY AE]
Z Setting the aperture
This is an automatic mode to set the aperture.
Use this mode to have the area in front of and behind the
subject out of focus (large aperture) or have both near
and far subjects in focus (small aperture).
ISO 100
Set the Mode dial to <.
SETTING APERTURE
F3. 5
F3
Aperture
A Press D to open the setting screen.
Shooting functions:
• [ PHOTOMETRY] (➝p.80)
• [T WHITE BALANCE] (➝p.81)
• [H FOCUSING] (➝p.83)
• [ AF MODE] (➝p.84)
• [G SHARPNESS] (➝p.86)
• [ FLASH] (➝p.87)
• [ BRACKETING] (➝p.87)
B Press n or o to select the aperture.
Advanced Features — Photography
1000
C Press the shutter button to take pictures.
CHECK
See p.65 for information on the available flash modes.
Continued Q
57
Setting the Shooting Mode
CAUTION
ISO 100
4
SET
F8
4
Lit red
ISO 100
58
Aperture
By adjusting the aperture, you can change the depth of focus
(depth of field). Selecting a larger number of aperture (closed)
obtains a larger depth of focus. Selecting a smaller number of
aperture (open) has the area in front of and behind the subject
out of focus.
Closed
When the brightness of the
subject is outside the camera’s
brightness metering range,
[----] appears as the shutter
speed.
F8
The area in front of and
behind the subject is also in
focus in the shot.
Main subject
Open
SET
----
When the correct exposure
cannot be obtained with
selected aperture setting, the
shutter speed appears in red.
When this occurs, adjust the
aperture setting again.
When [d FORCED FLASH] is
set, you can take a picture with
a shutter speed of up to 1/45
sec.
The area in front of and
behind the subject is out of
focus.
[> MANUAL]
Z Setting the shutter speed
This is a shooting mode that allows for settings including
the shutter speed and aperture.
Set the Shooting functions to manual to easily control
yourself.
ISO 100
Set the Mode dial to >.
SET SHUTTERSPEED,APERTURE
F3. 5
F3
Shutter speed
A Press D to open the setting screen.
Shooting functions:
• [ PHOTOMETRY] (➝p.80)
• [T WHITE BALANCE] (➝p.81)
• [H FOCUSING] (➝p.83)
• [ AF MODE] (➝p.84)
• [G SHARPNESS] (➝p.86)
• [ FLASH] (➝p.87)
• [ BRACKETING] (➝p.87)
B Press n or o to select the shutter speed.
Advanced Features — Photography
1000
C Press the shutter button to take pictures.
CHECK
See p.65 for information on the available flash modes.
MEMO
• Use a tripod to prevent camera shake.
• In shots with long exposures, noise (dots) may appear
on the image.
Continued Q
59
Setting the Shooting Mode
CAUTION
If the shutter speed is set to a speed 1/1000 sec.,
smearing (white stripes) may appear in the image
(➝p.156).
The exposure indicator
ISO 100
Z Setting the aperture
SET
ISO 100
1000
Aperture
1000
SET SHUTTERSPEED,APERTURE
F3. 5
F3
A Press D to open the setting screen.
B Press p or q to select the aperture.
C Press the shutter button to take pictures.
60
F3. 5
F3
Use the exposure indicator
on the screen as a guide
when setting the
exposure.When the
brightness of the subject is
outside the camera’s
brightness metering range,
the exposure indicator
disappears on the screen.
Adjusting the Image Brightness (D Exposure Compensation)
Use this menu for shots to get the correct brightness
(exposure), such as shots with extremely high contrast
between the subject and the background.
Available Shooting modes: N, M, <
Adjusting exposure
compensation
Exposure Compensation
indicator
SET
60
F3. 5
F3
A Press D to open the setting screen.
B Press p or q to set the compensation
value.
C Press D to confirm the setting.
CAUTION
This function can only be used for N, M, < in Shooting
mode.
Advanced Features — Photography
Press D to display the exposure compensation setting
screen.
ISO 100
D Press the shutter button to take pictures.
CHECK
• The symbol indicating the compensation direction (– or
+) turns yellow.
• The S icon also turns yellow while exposure
compensation is being set and then turns blue after
setting is completed.
• The screen brightness will increase or decrease
depending on the exposure compensation setting.
Continued Q
61
Adjusting the Image Brightness (D Exposure Compensation)
positive (+) compensation
negative (–) compensation
Guide to compensation
• Backlit portraits: +2 steps to
+4 steps (+2/3 EV to +1 1/3
EV)
• Very bright scenes (such as
snowfields) and highly
reflective subjects: +3 steps
(+1 EV)
MEMO
• This setting is retained when the mode is changed or
the camera is turned off (S icon appears). Set the
exposure compensation to “0” unless compensation is
required.
• Any of the following disables exposure compensation:
- Using the flash in [AUTO] or
mode
- Shooting dark scenes in d or
mode
62
• Shots made up predominantly of sky: +3 steps (+1 EV)
• Spotlit subjects, particularly against dark backgrounds: –2
steps (–2/3 EV)
• Scenes with low reflectivity, such as shots of pine trees or
dark foliage: –2 steps (–2/3 EV)
e Macro/> Super Macro (Close-up)
Use this mode to take close-up shots.
Available Shooting modes: B,
,
,
), N, M, <, >
MEMO
,
/
(
,
Press e (p) to select Macro mode.
The Macro mode setting changes each time you press the
e (p).
e or > appears on the
screen indicating that you
can take close-up shots.
Advanced Features — Photography
AUTO
• Use a tripod to prevent camera shake in Macro mode.
• Any of the following cancels Macro mode:
- Changing the Mode dial to
,
or r mode
- Turning the camera off
• If the flash is too bright, use flash brightness adjustment
(➝p.87).
• Even if [
MULTI] (➝p.85) in the [
AF MODE] is set,
the camera focuses near the center of the screen.
• AF-assist may not function correctly if the camera is up
close to the subject, such as in macro-mode.
CAUTION
• When Super Macro is set, focal length is fixed to 60 mm
(35 mm camera equivalent). Zoom function is not
available.
• When Super Macro is set, flash cannot be used.
63
d Setting the Flash
Flash photography is useful for taking pictures at night or
indoor dark locations. Choose from 6 flash modes
according to the type of shot. See p.65 for information on
the available Shooting modes.
Use this mode for ordinary photography.
The flash fires as required by the shooting conditions.
1
[
Press the Flash pop-up button to pop up the
flash.
[
AUTO FLASH]
RED EYE REDUCTION]
This mode is suitable for shooting portraits in
low-light conditions.
Use this mode to minimize red-eye (eyes
appear in red in the finished photo).
MEMO Red-eye effect
2
Turn the Command dial to select the flash
mode setting.
When using the flash to take a picture of people in lowlight conditions, their eyes sometimes appear red in the
picture. This is caused by the light of the flash reflecting
off the inside of the eye.
[d FORCED FLASH], [
FLASH]
FORCED
Use this mode in backlit scenes, or to get the correct
colors when taking a picture under bright lighting. In this
mode, the flash fires in bright as well as dark conditions.
Using
synchronizes Red-eye reduction mode.
The flash setting changes each
time you press d (q).
When [
FACE
DETECTIONbREMOVAL ON] is set.
MEMO
When pressing the shutter button down halfway, b
appears on the screen before the flash fires.
64
[c SLOW SYNCHRO],
[n RED EYE & SLOW]
ON
b OFF
ON
b ON
OFF
CAUTION
In bright scenes, overexposure may occur.
Suppressed flash
Pressing the flash down
changes the camera to
Suppressed flash mode.
This mode is suitable for
situations where the flash
cannot be used. Use a tripod
to prevent camera shake
when shooting in
Suppressed flash mode in
the dark condition.
AUTO
d
B
✓
✓
H
✓
✓
✓
✓
c
✓
n
✓
✓
✓
✓
✓
,
.
✓
/
✓
✓
Advanced Features — Photography
This mode allows you to take pictures of people at night
that clearly show both your subjects and the night time
backdrop. To prevent camera shake, always use a tripod.
Using n synchronizes Red-eye reduction mode.
Using / selects slow shutter speeds of up to 8 seconds.
Z Available flash modes in Shooting modes
Available flash modes in each Shooting mode are listed
below.
: FACE DETECTION
b: RED EYE REMOVAL
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
N
✓
✓
✓
✓
M
✓
<
✓
>
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
Continued Q
65
d Setting the Flash
CAUTION Notes on using flash
• If the shutter speed is set to a speed faster than 1/1000
sec., the image may appear dark even if the flash is
used.
• If pressing the shutter button while the flash is charging
(indicator lamp blinking orange), the picture will be
taken without the flash (when using [AUTO] and
).
• The flash charging time may increase when the
batteries are low on charge.
• When taking a picture using the flash, the image may
disappear and go dark briefly due to flash charging. The
indicator lamp blinks orange during charging.
• The flash fires several times (pre-flashes and the main
flash). Do not move the camera until the picture is
taken.
66
* Self-Timer
The self-timer is used in situations where the
photographer is included in the shot.
Available Shooting modes: All
Setting self-timer
The last displayed setting
is the selected mode.
AUTO
OFF
:The picture is taken
after 10 seconds.
(: The picture is taken
after 2 seconds.
1
Press the shutter button down halfway to
focus on the subject and press the shutter
button fully.
Double
beep
Halfway pressed
Beep
Fully pressed
Pressing the shutter button down halfway that focuses
on the subject.
Without releasing the shutter button, press the button
all the way down (fully pressed) to start the self-timer.
Advanced Features — Photography
The self-timer setting changes each time you press *
(o).
Taking pictures using self-timer
Continued Q
67
* Self-Timer
2
Take pictures in selected time.
A picture is taken after the self-timer lamp changes from
lit to blinking (only blinks with the 2-second self-timer).
Using the 2-second self-timer
This is useful when you worry about camera shake even if
attaching the camera on a tripod.
MEMO
• To stop the self-timer, once it has started running, press
DISP/BACK.
• Any of the following cancels the self-timer setting:
- Completing the shooting
- Changing the Shooting mode setting
- Setting the camera to Playback mode
- Turning the camera off
• Take care not to stand in front of the lens when pressing
the shutter button as this can prevent the correct focus
or brightness (exposure) from being achieved.
9
A countdown appears on
the LCD monitor indicating
the time remaining until the
picture is taken.
Taking pictures with the selftimer and Intelligent Face
Detection function
Available Shooting modes: B,
,
/
(H, /,
,
,
,
,
,
), N, M, <, >
Intelligent Face Detection
The Intelligent Face Detection function is especially
useful when using the self timer since it ensures that
faces will appear in focus automatically.
68
f Taking pictures continuously
Use this mode to take pictures of a moving subject.
A Press f to display the continuous shooting setting
screen.
TOP15
OFF
[
TOP 152] : Continuous shooting
[
TOP 6[] : Continuous shooting
[h LONG PERIOD] : Long period continuous shooting
[k LAST 3]: Continuous shooting
[j BRACKETING] : Auto bracketing
[f TOP 3] : Continuous shooting
B Press n or o to select a Continuous
shooting mode.
C Press MENU/OK to confirm the setting.
• Shooting continues as long as holding the shutter
button down. In auto bracketing mode however, just
press the shutter button once to shoot 3 frames.
• Number of available frames is limited depending on the
available space on the Memory Card or internal
memory. When auto bracketing, if there is insufficient
space on the Memory Card or internal memory to
record 3 frames, no pictures are taken.
• The focus is determined in the first frame and cannot be
changed in mid-sequence (except for [LONG
PERIOD]).
• The exposure is determined in the first frame, but in
[LONG PERIOD] continuous shooting the exposure is
adjusted for the scene being shot.
• The speed of continuous shooting varies depending on
the shutter speed.
• The flash cannot be used as the flash mode is set to
Suppressed flash. However, when the mode is changed
back to normal photography, the flash setting specified
before continuous shooting was selected is restored.
• For [TOP 3] continuous shooting and Auto bracketing,
the results are always displayed after you shoot. Note
that pictures taken using [LONG PERIOD] continuous
shooting are recorded without displaying the results.
• In [LONG PERIOD] continuous shooting mode, only 1
frame can be shot when using the [LONG PERIOD]
continuous shooting mode and Self-timer mode
together.
• File recording time using [TOP 3] or [BRACKETING]
may increase when record to a Memory Card or internal
memory.
Advanced Features — Photography
CONTINUOUS
CAUTION
Continued Q
69
f Taking pictures continuously
[
TOP 152]
Available Shooting modes: All (except for
[
)
Shooting continues up to 15 frames as long as the shutter
button is held down. Use this setting when your priority is
continuous shooting speed over image quality, during
continuous shooting.
MEMO
• Whitish lines may appear around a bright spot in an
image when using [
TOP 152]. In this case, use
[
TOP 6[].
• [
QUALITY] (➝p.78) is limited to 2. The
[
QUALITY] setting changes and is displayed in
yellow in the LCD monitor. When Shooting mode is set
to other than [
TOP 152], the restriction is cleared.
70
TOP 6[]
Available Shooting modes: All (except for
)
Shooting continues up to 6 frames as long as the shutter
button is held down.
MEMO
[
QUALITY] (➝p.78) is limited to [. The
[
QUALITY] setting changes and is displayed in yellow.
When Shooting mode is set to other than [
TOP 6[],
the restriction is cleared.
[h LONG PERIOD] continuous
shooting
Available Shooting modes: All (except for
[k LAST 3] continuous shooting
Available Shooting modes: All (except for
Release
shutter button.
All frames
MEMO
Shooting continues as long as holding the shutter button
down.
This mode shoots up to 40 times. The camera records the
final 3 frames shot when you release the shutter button.
Max.40 shots
Press shutter
Release
button.
shutter button.
3 frames
Advanced Features — Photography
Shooting continues as long as the shutter button is held
down. This mode shoots up to Memory Card or internal
memory end.
Press shutter
button.
)
)
Continued Q
Continuous shooting mode and assist window (➝p.35)
can be used together.
71
f Taking pictures continuously
[j BRACKETING]
[f TOP 3] continuous shooting
Available Shooting modes: N, M, <, >
Available Shooting modes: All (except for
This mode shoots the same
image with different exposure
settings.
Bracketing shoots 3
continuous frames, each with
a different exposure setting.
is correctly exposed,
is overexposed and
is
underexposed.
The exposure range settings
can be changed in [
BRACKETING] in the
[SHOOTING MENU].
STORING
CHECK
Auto bracketing settings (3) ±1/3 EV, ±2/3 EV, ±1 EV
CAUTION
• If the underexposed or overexposed frame is outside
the camera’s control range, the picture is not taken with
the specified setting increments.
• This function can only be used for N, M, < or > in Shooting
mode.
MEMO Changing the setting (exposure range)
SHOOTING MENU
FLASH
BRACKETING
SET - UP
72
0
+1/
EV
EV
+
- 1 EV
3
+2
- /3
-
Press the MENU/OK to
display the menu and change
the setting in the [
BRACKETING] menu option
(➝p.87).
STORING
)
Shooting continues as long as
holding the shutter button
down. This mode shoots up to
3 frames.
j Increasing LCD Monitor Brightness
This is useful when checking the shot composition for
outdoor scenes.
Increasing the LCD monitor
brightness
blinks on the LCD monitor
when the function is active.
AUTO
• This function is automatically canceled after each shot.
• When this function is active, it will increase the amount
of speckling in images on the screen. This is normal and
does not affect the photographed image.
• This function is purely for checking the composition of
your shot. It does not increase the brightness of the
image.
• Even if you increase the brightness in low-light
conditions, you cannot check the subject.
• The color tones may vary depending on the subjects.
Advanced Features — Photography
Press j (n) to increase the LCD monitor brightness.
Press j (n) again to return to normal LCD monitor
brightness.
MEMO
UP
12/ 31
12
31/ 2050
10: 00 AM
10
73
Using [p-MODE MENU] (Photography)/[SHOOTING MENU]
Use these menus to adjust image quality or focus. You
can take pictures in a wide range of conditions.
Setting the [p-MODE MENU]
(Photography)
MODE MENU
ISO
QUALITY
F
N
4
9 FRAMES
11
19
30
38
169
A Press p button to open the [p-MODE
MENU].
Setting the [SHOOTING MENU]
SHOOTING MENU
PHOTOMETRY
MULTI
WHITE BALANCE
SPOT
HIGH - SPEED SHOOTING OFF
AVERAGE
FOCUSING
AF MODE
STD
SHARPNESS
A Press MENU/OK to open the [SHOOTING
MENU].
B Press n or o to select the menu.
C Press q.
B Press n or o to select the menu.
D Press n or o to change the setting.
C Press q.
E Press MENU/OK to confirm the setting.
D Press n or o to change the setting.
E Press MENU/OK to confirm the setting.
74
Z List of [p-MODE MENU] options
Settings
Factory
default
[S ISO]
(➝p.77)
Specifies required sensitivity setting of the ambient light around the
subject.
The larger value of the sensitivity, the higher sensitivity is obtained.
The higher sensitivity settings will allow you to take pictures in darker
locations.
[AUTO]/[AUTO (800)]/
[AUTO (400)]/
[32003]/[1600]/
[800]/[400]/[200]/
[100]/[64]
[AUTO]
F/
N/%/[/
3/2/`
[
QUALITY]
(➝p.78)
Specifies the image size.The larger image size, the better image
quality is obtained. The smaller image size, the larger number of
images are recorded.
[
FinePix COLOR]
(➝p.79)
Specifies required color tone.This mode is effective for taking more vivid
[STD]/
shots or black and white shots.
/
N
[STD]
Z List of [SHOOTING MENU] options
Menu
Functions
[
SCENE
POSITION]
(➝p.49)
This setting can be used when the Mode dial is set to
or
.
Use this setting to provide the best photography menu setting for the
scene being shot.
[
PHOTOMETRY]
(➝p.80)
This setting can be used when the Mode dial is set to N, M, < or >.
Use this setting to specify the light metering method.
Factory
default
Settings
H/,/./// /
/
/ / / /
/
/
/
:H
:,
/
[TWHITE
BALANCE]
(➝p.81)
This setting can be used when the Mode dial is set to N, M, < or >.
Use this setting to adjust the color balance to suit the color of the
ambient light around the subject.
[AUTO]/]/6/7/
9/0/-/8
[
When setting [. SPORT] mode, the camera sets to [
HIGHSPEED SHOOTING] mode automatically.
Use this setting to reduce the time required for focusing.
[ON]/[OFF]
HIGH-SPEED
SHOOTING]
(➝p.82)
Advanced Features — Photography
Functions
Menu
[AUTO]
[OFF]
Continued Q
75
Using [p-MODE MENU] (Photography)/[SHOOTING MENU]
Menu
Settings
[H FOCUSING]
(➝p.83)
This setting can be used when the Mode dial is set to N, M, <, or >.
Use this setting to specify the focusing mode.
/
[
This setting can be used when the Mode dial is set to N, M, <, or >.
Use this setting to specify the focusing area.
/
AF MODE]
(➝p.84)
[GSHARPNESS]
(➝p.86)
76
Functions
This setting can be used when the Mode dial is set to N, M, < or >.
Use this setting to soften or emphasize the outline of an image.
Factory
default
/
[SOFT]/
[STANDARD]/
[HARD]
[STANDARD]
[
FLASH]
(➝p.87)
This setting can be used when the Mode dial is set to N, M, < or >. –2/3 EV to +2/3 EV
Use this setting to adjust the amount of light emitted by the flash to suit in approx. 1/3 EV
the photography conditions or to achieve a desired effect.
increments
0
[
BRACKETING]
(➝p.87)
This setting can be used when the Mode dial is set to N, M, < or >.
±1/3 EV, ±2/3 EV,
Use this setting to photograph the same image with different exposure
±1 EV
settings.
±1/3 EV
[p-MODE MENU] (Photography)
Changing the sensitivity setting
([S ISO])
CHECK
• Settings
[AUTO]/[AUTO(800)]/[AUTO(400)]/[32003]/[1600]/
[800]/[400]/[200]/[100]/[64]
Selecting [AUTO]/[AUTO(800)]/[AUTO(400)] as the
sensitivity setting, the camera selects the best
sensitivity setting for the subject’s brightness.
ISO 100
60
The selected sensitivity
setting appears on the
screen when the
sensitivity setting is set
to the setting other than
[AUTO].
MEMO
• When anything other than N, M, < and > in the
Shooting mode is selected, only AUTO can be selected
for the ISO (sensitivity) setting.
• When N, M, < and > in the Shooting mode is selected,
AUTO cannot be selected for the ISO (sensitivity)
setting.
• [
QUALITY] is limited to 3, when [
ISO] is set to
3200. [
QUALITY] automatically changes and is
displayed in yellow in the LCD screen. When [
ISO]
is set to other than 3200, the restriction is cleared.
CAUTION
• Although higher sensitivity settings will allow you to take
pictures in darker locations, they will also increase the
amount of speckling in your images. Choose the
sensitivity setting that best suits the conditions.
• When 3200 is set for [SISO], image resolution will be
lower than if shot at a sensitivity setting lower than
1600.
Advanced Features — Photography
Use this menu to specify required sensitivity setting of the
ambient light around the subject.
The larger value of the sensitivity, the higher sensitivity is
obtained. The higher sensitivity settings will allow you to
take pictures in darker locations.
Setting the menu (➝p.74)
PROGRAM SHIFT
F3. 5
F3
• About [AUTO(800)]/[AUTO(400)]
[AUTO(800)]/[AUTO(400)] can be selected when the
Mode dial is set to N. For [AUTO(800)]/[AUTO(400)],
sensitivity is automatically set in the same way as for
[AUTO], but the highest sensitivity is limited. Select
[AUTO(800)]/[AUTO(400)] depending on the scene.
77
[p-MODE MENU] (Photography)
Changing the quality setting
([
QUALITY])
Setting the menu (➝p.74)
Area shot and quality setting
Area shot excluding %
Use this menu to specify the image size (number of
recorded pixels).
Select the quality setting for the scene being shot.
Area shot with %
AUTO
Z Quality settings in Shooting mode
Quality mode
Sample uses
F (3648 × 2736) Printing at up to 10R (25.4 × 30.5 cm/
N (3648 × 2736) 10 × 12 in.) / A4 size / A3 size
For better quality, select
F
% (3648 × 2432)
[ (2592 × 1944)
3 (2048 × 1536)
78
Printing at up to 6R (15.2 × 20.3 cm/
6 × 8 in.) / A5 size
2 (1600 × 1200)
Printing at up to 4R (10.2 × 15.2 cm/
4 × 6 in.) / A6 size
` (640 × 480)
To use for e-mail or web site
12/ 31
12
31/ 2050
10: 00 AM
10
12/ 31
12
31/ 2050
10: 00 AM
10
Normal shooting provides an aspect ratio of 4:3 and %
shooting provides an aspect ratio of 3:2 (same aspect ratio as
35 mm film and post card).
MEMO
• The bigger the number of recorded pixels, the better the
image quality becomes. As the number of recorded
pixels becomes smaller, you will be able to record more
frames to a Memory Card.
• The quality setting is retained even when the camera is
turned off or the mode setting is changed.
• When changing the quality setting, the number of
available frames also changes (➝p.154). The numbers
to the right of setting show the number of available
frames.
• [
ISO] is limited to 1600 when [
QUALITY] is set to
or %. The [
ISO] setting automatically changes
and is displayed in yellow in the LCD screen. When
[
QUALITY] is set to other than
or %, the
restriction is cleared.
Setting the menu (➝p.74)
Changing the FinePix COLOR
setting ([
FinePix COLOR])
Use this menu to specify required color tone.
It is effective for taking vivid shots or black and white
shots.
FinePix COLOR settings
The contrast and color saturation
[STD]
are set to standard.
[p-STANDARD] Use this mode for normal
photography.
[p-CHROME]
[p-B&W]
The contrast and color saturation
are set to high.
This mode is effective for taking
more vivid shots of subjects such
as flowers.
• The FinePix COLOR setting is retained even when the
camera is off or the mode setting is changed.
• [
p-CHROME] may have little visible effect with
some subjects or the scene being shot. You may not be
able to see any difference on the screen.
Advanced Features — Photography
CHECK
MEMO
This mode converts the colors in
the photographed image to black
and white.
When setting [
p-CHROME] or [
the icon appears on the screen.
p-B&W],
CAUTION
When the Mode dial is set to
appear on the screen.
or
,
does not
79
[SHOOTING MENU]
Selecting light metering method
([
PHOTOMETRY])
Available Shooting modes: N, M, <, >
(When Intelligent Face Detection is turned
OFF)
Use this setting when the correct exposure cannot be
obtained by the shooting conditions.
SHOOTING MENU
PHOTOMETRY
MULTI
WHITE BALANCE
SPOT
HIGH - SPEED SHOOTING OFF
AVERAGE
FOCUSING
AF MODE
STD
SHARPNESS
[) MULTI] (Pattern):Light metering where the camera
assesses the scene and selects the
correct exposure.
[_ SPOT]
: Light metering where the exposure
is optimized for the center of the
image.
[+ AVERAGE]
: Light metering where an average
value for the entire image is used.
80
Setting the menu (➝p.74)
To use the photometry modes effectively
• [MULTI]
In this mode, the camera uses automatic scene recognition
to analyze the subject and provide optimum exposure in a
wide range of shooting conditions.
• [SPOT]
This mode is useful for subjects with strongly contrasting
light and dark areas where you want to achieve the correct
exposure for a particular feature.
• [AVERAGE]
The advantage of this mode is that the exposure tends not
to change for different compositions or subjects. This mode
is particularly effective for shots of people wearing black or
white clothing and shots of scenery.
Setting the menu (➝p.74)
Adjusting color balance
([T WHITE BALANCE])
Available Shooting modes: N, M, <, >,
CUSTOM WB
WHITE BALANCE
AUTO
NEW WB
NOT CHANGE
[AUTO]: Automatic adjustment
]
: Select the white balance be using white paper to
suit the shooting conditions
6
: Shooting outdoors in good weather
7
: Shooting in shade
9
: Shooting under Daylight fluorescent lamps
0
: Shooting under Warm White fluorescent lamps
: Shooting under Cool White fluorescent lamps
8
: Shooting in incandescent light
CANCEL
MEMO
To use the white balance set previously, press the MENU/
OK without pressing the shutter button.
Advanced Features — Photography
Adjust the color balance based on white to suit the color
of the ambient light around the subject.
] Custom white balance
A Select ] custom white balance (➝p.74).
B Hold a piece of white paper under the light source for
setting the white balance, so that it fills entire the
screen. Then press the shutter button to set the white
balance.
C When the correct exposure is measured,
[COMPLETED!] appears. Press MENU/OK to confirm
the setting.
COMPLETED!
SET
CANCEL
Continued Q
81
[SHOOTING MENU]
Setting the menu (➝p.74)
ISO 100
OVER
----
PROGRAM SHIFT
F-- - -
Set the exposure
compensation again, using
a negative value (–) when
[OVER] appears and a
positive value (+) when
[UNDER] appears (➝p.61).
OVER or UNDER
Focusing the shot quickly
([
HIGH-SPEED SHOOTING])
Available Shooting modes: All (except for
)
Use this mode to reduce the time required for focusing
when pressing the shutter button down halfway.
It is useful to avoid missing snapshot opportunities.
SHOOTING MENU
Example
You can change the white balance for a photographed image
by using colored paper instead of white paper.
HIGH-SPEED SHOOTING ON
SET-UP
OFF
MEMO
• In AUTO mode, the correct white balance may not be
achieved for subjects such as close-ups of people’s
faces and pictures taken under a special light source.
Select the correct white balance for the light source.
• When the flash fires, the white balance (except for
custom white balance) setting for the flash is used.
Consequently, to achieve a particular effect, the flash
mode should be set to Suppressed flash (➝p.65).
• The specified custom white balance is retained until it is
reset. This setting is retained even if the batteries are
removed.
• The color tones may vary depending on the shooting
conditions (light source, etc.).
• After taking the picture, check the image color (white
balance).
• Explanation of Terms “White Balance” (➝p.157).
82
CAUTION
[
EVF/LCD MODE] in the [U SET-UP] menu is
automatically set to 60fps (➝p.156).
MEMO
• When taking pictures while the [HIGH-SPEED
SHOOTING] mode is set to [ON], the batteries will run
down more quickly.
• When setting . Sport mode, the camera sets to
[HIGH-SPEED SHOOTING] mode automatically.
Setting the menu (➝p.74)
Specifying the focusing mode
([H FOCUSING])
Available Shooting modes: N, M, <, >
(When Intelligent Face Detection is turned
OFF)
[
CONTINUOUS AF]
Use this setting to take pictures of a moving subject. The
camera continues to focus on the main subject in the AF
frame.
ISO 100
PHOTOMETRY
AUTO
WHITE BALANCE
HIGH - SPEED SHOOTING OFF
FOCUSING
CONTINUOUS AF
AF MODE
SINGLE AF
SHARPNESS
AF frame
60
PROGRAM SHIFT
F3.5
CAUTION
• When using [
CONTINUOUS AF], attention must be
given to the battery level.
The battery level (power consumption) increases when
using [
CONTINUOUS AF]. Because the camera
focuses continuously without pressing the shutter
button.
• When using [
CONTINUOUS AF], [
AF MODE] is
set to [
CENTER] automatically.
Advanced Features — Photography
Use this mode to specify focusing mode that best suits the
subject.
: [CONTINUOUS AF]
SHOOTING MENU
: [SINGLE AF]
Continued Q
83
[SHOOTING MENU]
[
Setting the menu (➝p.74)
Specifying the focusing area
([
AF MODE])
SINGLE AF]
Use this setting to take picture of a static subject such as
a landscape.
Available Shooting mode: N, M, <, >
(When Intelligent Face Detection is turned
OFF)
ISO 100
60
PROGRAM SHIFT
F3. 5
F3
Use this mode to specify the focusing area that best suits
the subject.
: [CENTER]
SHOOTING MENU
: [MULTI]
PHOTOMETRY
: [AREA]
AUTO
WHITE BALANCE
HIGH - SPEED SHOOTING OFF
FOCUSING
CENTER
AF MODE
MULTI
SHARPNESS
AREA
[
CENTER]
The camera focuses on the center of the screen.
Use this setting when taking pictures with AF/AE lock
(➝p.31).
ISO 100
60
84
PROGRAM SHIFT
F3. 5
F3
Setting the menu (➝p.74)
[
MULTI]
[
When pressing the shutter button down halfway, the
camera recognizes any strongly contrasting subject near
the center of the screen and displays the AF frame over
subject in focus.
AREA]
The camera changes the focusing position on the screen.
Use this setting when composing the shot using a tripod
and changing the focusing position.
SELECT AF AREA
Before moving
Target point
60
SET
PROGRAM SHIFT
F3.5
CANCEL
After moving
Halfway pressed
A Press n, o, p or q to move the
(target point) to the focusing position.
Advanced Features — Photography
ISO 100
ISO 100
AF frame
60
F3. 5
F3
CAUTION
When taking pictures in Macro mode, the camera focuses
on the center of the screen.
MEMO
60
PROGRAM SHIFT
F3. 5
F3
B The AF frame appears in the location to
which the target point was moved when
you press MENU/OK.
When the AF frame does not appear in the focusing
position, select [
CENTER] in the AF mode and use
AF/AE lock (➝p.31).
Continued Q
85
[SHOOTING MENU]
C Press the shutter button to take pictures.
Setting the menu (➝p.74)
Adjust the image outline (hard/
soft) ([G SHARPNESS])
Available Shooting modes: N, M, <, >
MEMO
• To reposition the AF frame, repeat step A.
• Regardless of the AF frame location, the exposure is
always set using the area in the center of the screen. To
expose the shot for your main subject, use AF/AE lock
(➝p.32).
86
Use this setting to soften or emphasize the outline and
quality of an image.
[HARD]:
SHOOTING MENU
Emphasizes the outlines.
Best for shots of subjects
PHOTOMETRY
such as buildings or text
AUTO
WHITE BALANCE
HIGH - SPEED SHOOTING OFF
where sharp images are
FOCUSING
HARD
desirable.
AF MODE
STANDARD
SHARPNESS
[STANDARD]:
SOFT
Best for ordinary
photography. Provides edge
sharpness that is ideal for
most picture taking situations.
[SOFT]:
Softens the outlines. Best for
shots of subjects such as
people, where a softer image
is desirable.
Setting the menu (➝p.74)
Adjust the amount of light
emitted by the flash
([
FLASH] (Brightness
Adjustment))
Available Shooting modes: N, M, <, >
SHOOTING MENU
FLASH
BRACKETING
SET - UP
Available Shooting modes: N, M, <, >
Use this setting to photograph the same image with
different exposure settings. Bracketing shoots 3
continuous frames, one of which is correctly exposed
while the remaining two are underexposed and
overexposed respectively by a set amount.
SHOOTING MENU
+2/3
AUTO
+1/3
+- 0
- 1/3
- 2/3
0
FLASH
BRACKETING
SET - UP
0
+1/
EV
EV
+
- 1 EV
3
+2
- /3
-
Advanced Features — Photography
Use this setting to change the amount of light emitted by
the flash to suit the photography conditions or to achieve
a desired effect.
Photograph the same image with
different exposure
([
BRACKETING])
CAUTION
• Depending on the type of subject and the shooting
distance, brightness adjustment may have no effect.
• The image may appear dark when setting the shutter
speed to higher than 1/1000 sec.
87
[SHOOTING MENU]
Setting the menu (➝p.74)
CAUTION
• If the underexposed or overexposed frame is outside
the camera’s control range, the picture is not taken with
the specified setting increments.
• Flash photography cannot be used.
• This feature always takes 3 shots. However, if there is
insufficient space on the Memory Card or internal
memory for 3 shots, no picture will be taken.
MEMO Auto bracketing
After setting the exposure for
bracketing, select [j
BRACKETING] by pressing
f.
CONTINUOUS
BRACKETING
OFF
88
Playback Information
CAUTION
Shooting information can be checked when the camera is
set to single-frame playback mode. Press D to check the
information. Press D again to return to playback mode.
• Highlight warning
100-0002
100
0002
F
ISO 400
1/60 F3.5
:STD
STD
:OFF
OFF
:AUTO
AUTO
:+1
12/ 31
12
31/ 2050 10
10:00
00 AM
Overexposed area blinks in
black.
Highlight warning
A Quality mode
B Sensitivity
C Shutter speed/Aperture
D FinePix COLOR
E Flash
F White balance
G Exposure compensation setting
H Frame number
I Histogram
A histogram is a chart showing the distribution of brightness in
an image (horizontal axis: brightness; vertical axis: pixels).
Pixels
F
ISO 400
1/60 F3.5
:STD
STD
:OFF
OFF
:AUTO
AUTO
:+1
12/ 31
12
31/ 2050 10
10: 00 AM
Brightness
Shadows
Highlights
A Optimal exposure:
There is an ample distribution of
pixels overall with a peak in the
middle range.
B Overexposed:
The number of highlight pixels
is high with the distribution
sloping upwards to the right.
Advanced Features — Playback
Histograms
100-0002
100
0002
C Underexposed:
The number of shadow pixels is
high with the distribution sloping
upwards to the left.
CAUTION
The shape of the graph will vary depending on the
subject.
89
Using [p-MODE MENU] (Playback)/[PLAYBACK MENU]
Use these menus to playback photographed images.
Setting the [p-MODE MENU]
(Playback)
Setting the [PLAYBACK MENU]
A Set the camera to Playback mode (➝p.36).
A Set the camera to Playback mode (➝p.36).
PLAYBACK MENU
MODE MENU
SLIDE SHOW
PRINT ORDER (DPOF)
B Press p button to open the [p-MODE
MENU].
ERASE
RED EYE REMOVAL
IMAGE ROTATE
PROTECT
COPY
VOICE MEMO
B Press MENU/OK to open the [PLAYBACK
MENU].
C Press n or o to select the menu.
C Press n or o to select the menu.
D Press q.
D Press q.
E Press n or o to change the setting.
E Press n or o to change the setting.
F Press MENU/OK to confirm the setting.
F Press MENU/OK to confirm the setting.
90
[p-MODE MENU] (Playback)
Setting automatic playback
([
SLIDE SHOW])
Use this mode to playback photographed images
continuously. You can select type of image transition.
Setting the menu (➝p.90)
DPOF set frame
([
PRINT ORDER (DPOF)])
You can specify the image, number of prints, with or
without date of printing with a DPOF-compatible printer.
MODE MENU
MODE MENU
MEMO
• To interrupt automatic playback, press MENU/OK.
• Press p or q to advance or go back through the
images when selecting [NORMAL] and [FADE-IN].
• The Auto power off function (➝p.118) does not operate
during playback.
• Movie starts automatically. When the movie ends, the
playback function moves it on.
• Press DISP/BACK once during playback to display onscreen help.
• The date is displayed on the Slide Show (except
[MULTIPLE]) if the date is displayed on the SingleFrame Playback.
• The camera plays back the image taken with Intelligent
Face Detection (➝p.29) zoomed in on the detected face
when [NORMAL
] or [FADE-IN
] is selected.
SLIDE SHOW
PRINT ORDER (DPOF)
WITH DATE
WITHOUT DATE
RESET ALL
[WITH DATEE] : The date will be imprinted on your
prints.
[WITHOUT DATE]: The date will not be imprinted on your
prints.
[RESET ALL]
: All DPOF settings will be canceled.
Continued Q
Advanced Features — Playback
SLIDE SHOW
NORMAL
PRINT ORDER (DPOF)
NORMAL
FADE-IN
FADE-IN
MULTIPLE
CLOCK
91
[p-MODE MENU] (Playback)
[WITH DATE] / [WITHOUT DATE]
Selecting [WITH DATEE], E appears on the screen
and the date will be imprinted on your prints.
PRINT ORDER (DPOF)
DPOF : 00009
Total number of prints
Setting for that frame
Setting the menu (➝p.90)
MEMO Canceling DPOF setting
A Press p to open the [p-MODE MENU] and press n
or o to select [
PRINT ORDER (DPOF)].
B Press q.
C Press n or o to select [WITH DATE E] or
[WITHOUT DATE] and press MENU/OK to display the
print order screen.
D Press p or q to select the frame (file) with the DPOF
setting you want to cancel.
E Press o to set the number of prints to 0 (zero).
01 SHEETS
FRAME
SET
A Press p or q to display the frame (file)
for specifying DPOF setting.
B Press n or o to set a value.
Up to 99 sheets are printed.
For frames (files) that you do not want
printed, set the number of prints to 0
(zero).
To specify more DPOF settings, repeat steps A and B.
C Always press MENU/OK after the settings
are completed.
Pressing DISP/BACK cancels those
settings.
D Press MENU/OK again. The total number
of prints appears on the screen.
92
To cancel the DPOF setting for another frame (file),
repeat steps D and E.
Always press MENU/OK to complete the settings.
• [RESET ALL] (➝p.94)
Setting the menu (➝p.90)
Intelligent Face Detection
MEMO
• When DPOF settings were specified on another
camera.
PRINT ORDER (DPOF)
DPOF : 00000
RESET DPOF OK?
00 SHEETS
FACE COUNT
FRAME
YES
SET
NO
CAUTION
When DPOF settings are set to the images taking with the
Intelligent Face Detection (➝p.29) (
appears on the
screen), press
(Intelligent Face Detection), the frame
appears around the detected face, and then the number
of the detected faces is set to print number. It is easy to
set the number of prints for each person in the picture.
Press n or o to set the print number. Press
(Intelligent Face Detection) again, the number of the
detected faces is set to the print number. After setting,
press MENU/OK.
Continued Q
Advanced Features — Playback
When the data includes a frame (file) with DPOF
settings that were specified on another camera,
[RESET DPOF OK?] appears.
Pressing MENU/OK erases all of the DPOF settings
already specified for each frame (file). Specify the
DPOF setting for each frame (file) again.
• Prints of up to 999 frames (files) can be ordered on the
same Memory Card.
• DPOF settings cannot be specified for movies.
• Pressing DISP/BACK while choosing settings will
cancel all current settings. If there were previous DPOF
settings, only the modifications are canceled.
• When selecting the [WITH DATE E] setting, the date
is imprinted on your shots using the Print Service or a
DPOF-compatible printer (depending on the printer
specifications, the date may not be printed in some
cases).
• Images photographed with a camera other than FinePix
S1000fd may not be specified DPOF settings.
93
[p-MODE MENU] (Playback)
Setting the menu (➝p.90)
[RESET ALL]
To cancel all DPOF settings:
RESET DPOF OK?
YES
CANCEL
Select [RESET ALL] in the [p-MODE MENU] (➝p.91).
Press MENU/OK.
MEMO
100-0001
100-0001
100
0001
12/ 31
12
31/ 2050
10: 00 AM
10
u appears on the screen during playback when the
image has specified DPOF settings.
94
Setting the menu (➝p.90)
Z [u PRINT ORDER (DPOF)]
DPOF stands for Digital Print Order Format and refers to a format that is used for recording printing specifications
for images shot using a digital camera on media such as a Memory Card. The recorded specifications include
information on which frames are to be printed.
*Some printers do not support date and time imprinting or specification of the number of prints.
*The warnings shown below may appear while specifying the prints.
[RESET DPOF OK ?] (➝p.93)
When inserting a Memory Card that contains images specified for printing by another camera, those print specifications are all reset
and replaced by the new print specifications.
[DPOF FILE ERROR] (➝p.142)
Up to 999 images can be specified on the same Memory Card.
Advanced Features — Playback
[DPOF SPECIFIED. ERASE OK ?]
[DPOF SPECIFIED. ERASE ALL OK ?] (➝p.43)
When erasing the image, the DPOF setting for that image is deleted at the same time.
95
[PLAYBACK MENU]
Correcting red-eye effect in
images
([
RED EYE REMOVAL])
You can correct the red-eye effect in images taken with
the Intelligent Face Detection (➝p.29) (
appears on
the screen).
REMOVAL OK?
Setting the menu (➝p.90)
CAUTION
• Correction results may differ depending on scene.
• The processing may take more time if there are many
faces in the image.
• Images photographed with a camera
other than
FinePix S1000fd cannot be red-eye corrected.
• The corrected image is added as a separate file in the
final frame and
is indicated in the image.
• A red-eye corrected image is shown with a
. The
image cannot be corrected again.
CHECK
DETECTING
YES
CANCEL
A Press p or q to select the frame taken
with the Intelligent Face Detection.
B Press MENU/OK to open [PLAYBACK
MENU].
C Press n or o to select [
REMOVAL].
RED EYE
D Press q.
E Press MENU/OK to perform removal.
96
ARed-eye effect in an image
will be detected.
CANCEL
REMOVING
BProcessing will end when the
red-eye effect is not detected.
Setting the menu (➝p.90)
Rotating the images
([
IMAGE ROTATE])
IMAGE ROTATE
When shooting in the vertical position, the image appears
horizontal on the screen.
Use this mode to rotate an image and to display correct
direction. Your camera calls images “frames”.
CAUTION
MEMO
An image can be rotated only when playing back using
FinePix S1000fd.
You may not be able to rotate images that were shot with
a camera other than the FinePix S1000fd.
The panoramic picture cannot be rotated.
CANCEL
E Press n or o to rotate the image.
o: Rotates the image clockwise at a 90
degree angle.
n: Rotates the image counterclockwise at
a 90 degree angle.
A Press p or q to select the rotating frame
(file).
Advanced Features — Playback
Protected frames (files) cannot be rotated. Unprotect the
frames (files) before rotating them (➝p.98).
SET
B Press MENU/OK to open the [PLAYBACK
MENU].
C Press n or o to select [
ROTATE].
D Press q.
IMAGE
F Press MENU/OK to confirm the setting.
Next time the image is played back, it will
be automatically rotated.
Press DISP/BACK to cancel rotating the
image.
97
[PLAYBACK MENU]
Setting the menu (➝p.90)
Protecting the images
([
PROTECT])
[SET ALL]
Use this mode to prevent frames (files) from being
accidentally erased. Your camera calls images “frames”.
SET ALL OK?
IT MAY TAKE A WHILE
[FRAME] (set or reset a frame)
YES
To protect or unprotect only the selected frame (file):
PROTECT OK?
UNPROTECT OK?
CANCEL
Press MENU/OK to protect all the frames
(files).
[RESET ALL]
YES
CANCEL
Unprotected
YES
CANCEL
Protected (F appears)
RESET ALL OK?
IT MAY TAKE A WHILE
A Press p or q to select the protecting/
unprotecting frame (file).
B Press MENU/OK to protect/unprotect the
currently displayed frame (file).
Unprotected: protecting frame (file)
Protected: reset frame (file)
To protect another frame (file), repeat steps A and B.
When protecting frames (files) is completed, press DISP/
BACK.
98
YES
CANCEL
Press MENU/OK to unprotect all the frames
(files).
Setting the menu (➝p.90)
MEMO To stop the procedure midway
Copying the images
([V COPY])
It is possible to transfer saved images between the
internal memory and a Memory Card. Your camera calls
images “frames”.
CANCEL
CAUTION
The Format function erases all the frames (files),
including protected frames (files) (➝p.117).
COPY
INTERNAL MEMORY
CARD
CARD
INTERNAL MEMORY
NEXT
CANCEL
A Press n or o to select [Y INTERNAL
MEMORY Q \ CARD] or [\ CARD Q
Y INTERNAL MEMORY].
Advanced Features — Playback
If the images are very large, protecting or unprotecting all
the frames (files) may take some time.
If you want to take a picture or record a movie during the
procedure, press DISP/BACK.
Z Selecting COPY
B Press q.
Copying the images to another Memory Card
Copy images from the Memory Card inserted in your camera
to the internal memory using the Copy Image function, then
remove that Memory Card and insert another Memory Card
into the camera. Then, copy the images to the Memory Card
from the internal memory.
Continued Q
99
[PLAYBACK MENU]
Setting the menu (➝p.90)
Copying one frame at a time ([FRAME])
Copying all frames ([ALL FRAMES])
COPY
COPY
INTERNAL MEMORY
CARD
FRAME
CARD
INTERNAL MEMORY
ALL FRAMES
INTERNAL MEMORY
CARD
FRAME
CARD
INTERNAL MEMORY
ALL FRAMES
YES
YES
CANCEL
A Press n or o to select [FRAME].
A Press n or o to select [ALL FRAMES].
B Press MENU/OK.
B Press MENU/OK.
C Press p or q to select the copying frame
(file).
C Press MENU/OK to copy all the frames
(files).
D Press MENU/OK to copy the currently
displayed frame (file).
MEMO
To copy another frame (file), repeat steps C and D.
When copying frames (files) is completed, press DISP/
BACK.
100
CANCEL
CAUTION
• When [\ MEMORY FULL] or [Y MEMORY FULL]
appears on the screen, copying the data stops on the
way.
• When copying the image that has specified DPOF
setting, the DPOF setting is not copied.
Setting the menu (➝p.90)
Adding voice memos to the
images ([
VOICE MEMO])
REC STANDBY
30s
Voice memos of up to 30 seconds can be added to still
images.
START
Recording voice memos
A Press p or q to select the image to add
a voice memo.
E Press MENU/OK to start recording.
The remaining recording time appears during recording.
RECORDING
C Press n or o to select [
MEMO].
28s
Remaining
time
VOICE
Blinking red
D Press q.
REC
RE - REC
Advanced Features — Playback
B Press MENU/OK to open the [PLAYBACK
MENU].
CANCEL
MEMO
Microphone
Face the microphone to record your comment.
Hold the camera about 20 cm (7.9 in.) away for the best
results.
Continued Q
101
Setting the menu (➝p.90)
[PLAYBACK MENU]
Playing back voice memo
FINISH
A Press p or q to select an image file with
a voice memo. # appears on the screen.
REC
B Press o to start playing back the voice
memo.
RE - REC
F The voice memo ends when pressing
MENU/OK midway or 30 seconds pass.
15s
To record your comment: press MENU/OK.
To rerecord the comment: press DISP/BACK.
The playback time appears on
the screen along with a
progress bar.
MEMO
• When the image already has a voice memo
If you select an image that
already has a voice memo, a
screen appears in which you
can select whether to rerecord
the memo.
PLAYBACK MENU
ERASE
RED EYE REMOVAL
IMAGE ROTATE
PROTECT
COPY
VOICE MEMO
STOP
PAUSE
Progress bar
CAUTION
BACK
RE - REC
• When [PROTECTED FRAME] appears, unprotect the
frame (➝p.98).
• Voice memos cannot be added to movies.
Speaker
Uncover the speaker.
The sound may be difficult to hear.
102
Setting the menu (➝p.90)
Z Playing back voice memos
Control
Playback
Adjusting volume of voice memos
Description
Playback begins.
The voice memo stops when
playback ends.
Volume can be adjusted while playing back voice memos.
VOLUME
7
Pause /
Resume
Stop
Stops playback.
Press p or q while voice
memo playback is stopped to go
back to the previous file or
advance to the next file
respectively.
Fast forward /
Rewind
Press p or q during playback
to skip forwards or backwards
through the voice memo.
These buttons do not function
while playback is paused.
CHECK
SET
CANCEL
A Press MENU/OK while playing back voice
memo.
The voice memo is paused during
playback.
B Press n or o to adjust the volume.
Advanced Features — Playback
Pauses the voice memo during
playback.
Press o again to resume
playback.
C Press MENU/OK to confirm your selection.
Camera starts to play back the voice
memo.
• Audio recording format:
WAVE (➝p.156), PCM recording format
• Audio file size:
Approx. 480 KB (for a 30-second voice memo)
MEMO Playing voice memo files
You may not be able to play back some voice memo files
recorded on other cameras.
103
[PLAYBACK MENU]
Setting the menu (➝p.90)
Trimming the images
([
TRIMMING])
TRIMMING
Navigation screen
(Current displayed image)
Use this mode to trim the required part of the
photographed image.
CHECK
YES
Before selecting [
frame (file).
W:wide zoom lever
(Zoom out)
TRIMMING
CANCEL
TRIMMING], select the trimming
T:tele zoom lever
(Zoom in)
B Press n, o, p or q to move to another
part of the image.
C Press MENU/OK.
TRIMMING
REC OK?
YES
CANCEL
YES
CANCEL
Zoom bar
REC
A Turn to T or W to zoom in or out on an
image.
104
CANCEL
D Check the saved image size and press
MENU/OK.
The trimmed image is added as a separate
file in the final frame.
Setting the menu (➝p.90)
Intelligent Face Detection
MEMO
• A saved image size varies depending on the zoom
scale of step A. For 0.3 M, k YES option appears
in yellow.
• Image sizes
Printing at up to 6R (15.2 × 20.3 cm/6 × 8 in.) /
A5 size
2
Printing at up to 4R (10.2 × 15.2 cm/4 × 6 in.) /
A6 size
`
To use for e-mail or web site
• When % quality setting is selected, the image is
trimmed to normal size (4:3 aspect ratio).
CAUTION
You may not be able to trim images that were shot with a
camera other than FinePix S1000fd.
TRIMMING
YES
CANCEL
Images taken with the
Intelligent Face Detection
(➝p.29) (
appears on
the screen). Press
(Intelligent Face Detection),
the face that is focused on
is zoomed in to help crop
the main subject. To specify
a cropped part of the image
according to preference,
specify and adjust
according to the procedure
in [TRIMMING].
Advanced Features — Playback
[
3
TRIMMING
105
r Recording Movies
Use this mode to record movies with sound.
1
Set the camera to r Movie mode.
Z Zooming the image
You must zoom beforehand as you cannot zoom during
recording.
Set the Mode dial to r.
27s
STANDBY
Zoom bar
12/ 31
12
31/ 2050
999m13s
30s
STANDBY
12/ 31
12
31/ 2050
106
10: 00 AM
10
The available recording time
appears on the screen.
10: 00 AM
10
Turn the zoom lever to zoom in or out on an
image.
2
CHECK Recording movies
Record movies.
30s
REC 999m12s
• Specifications: Motion JPEG (➝p.156), Monaural
sound
• Quality selection method: % (640 × 480 pixels)
$ (320 × 240 pixels)
• Frame rate (➝p.156): 30 frames per second (fixed)
MEMO
Fully pressed
CAUTION
Recording ends when pressing the
shutter button down halfway during
recording or the remaining time
runs out.
Halfway pressed
MEMO
There is no need to hold down the shutter button during
recording.
• Because a movie is recorded onto the Memory Card or
internal memory as it is saved, it cannot be recorded
correctly if the camera suddenly loses power (if the
batteries run out or the AC power adapter and DC
coupler are disconnected).
• A movie file taken by FinePix S1000fd may not be
playable on other cameras.
• [
EVF/LCD MODE] in the [U SET-UP] menu is
automatically set to [30 fps] (➝p.156).
• Because sound is recorded concurrently with the
images, make sure that you do not cover the
microphone with a finger, etc. (➝p.12).
• Camera operation noises may be recorded during
movie shooting.
• The size of a movie file can be up to 2 GB.
Advanced Features — Movie
Press the shutter button down fully to start recording.
During recording, [lREC] and a counter that shows the
remaining time appear on the screen.
• The brightness and color of the screen shown during
movie recording may differ from those shown before
recording begins.
• The exposure and white balance will be automatically
adjusted to the scene being shot even after recording
has started.
• If recording is stopped immediately after it begins,
1 second of the movie is recorded onto the Memory
Card or internal memory.
107
r Recording Movies
Changing movie size
Press p to open the [p-MODE MENU].
MODE MENU
QUALITY
29s
53s
MEMO
• The quality setting is retained even when the camera is
turned off or the mode setting is changed.
• In r Movie mode, you cannot set the [S ISO]
(sensitivity) setting and [
FinePix COLOR] setting.
• See p.154 for information on recording times per
Memory Card or internal memory.
CAUTION
A Press q.
B Press n or o to change the setting.
C Press MENU/OK to confirm the setting.
Z Quality settings in Movie mode
% (640 × 480 pixels): For better quality
$ (320 × 240 pixels): To record longer movies
108
If you shoot using the xD-Picture Cards with model
numbers containing “M” such as DPC-M1GB, movie
recording time may be reduced if you repeatedly record
and erase (frame erase) image files.
In such a case, erase all frames or format the xD-Picture
Card before use. Back up important frames (files) onto
your PC or another media.
w Playing Back Movies
Setting the camera to w
Playback mode (➝p.36)
Z Playing back movies
Control
100- 0006
100
Playback
12/ 31
12
31/ 2050
PLAY
10: 00 AM
10
Pauses the movie during
playback.
Press o again to resume
playback.
Stop
Stops playback.
Press p or q while playback is
stopped to go back to the previous
file or advance to the next file
respectively.
Fast
forward /
Rewind
Press p or q during playback to
skip forwards or backwards
through the movie.
Skip
playback
Press p or q when the movie is
paused, the movie advances or
goes back one frame.
Hold down p or q to move
through the frames quickly.
B Press o to begin playing back movie.
STOP
PAUSE
Progress bar
The playback time appears on
the screen along with a
progress bar.
Advanced Features — Movie
Pause /
Resume
A Press p or q to select the movie file. r
appears on the screen.
34s
Description
Playback begins.
Playback stops when the end of
the movie is reached.
Continued Q
109
w Playing Back Movies
MEMO
If the subject of the shot is very bright, white vertical
streaks or black horizontal streaks may appear in the
image during playback. This is normal.
Setting the camera to w Playback mode (➝p.36)
Adjusting volume of movies
Volume can be adjusted while playing back movies.
VOLUME
CAUTION
• You may not be able to playback some movie files
recorded on other cameras.
• To playback movie files on a PC, save the movie file on
the Memory Card or internal memory to the PC’s hard
disk and then playback the saved file.
• Uncover the speaker. The sound is difficult to hear.
7
SET
CANCEL
A Press MENU/OK while playing back
movie.
The movie is paused during playback.
B Press n or o to adjust the volume.
C Press MENU/OK to confirm the setting.
Camera starts to playback the movie.
110
[U SET-UP]
Using the [SET-UP] menu
1
Open the [SET-UP] menu.
A Press MENU/OK to open the menu.
B Press n or o to select [U SET-UP].
C Press q.
2
Change the page.
DATE / TIME
BEEP VOLUME
SHUTTER VOLUME
PLAYBACK VOLUME
LCD BRIGHTNESS
FORMAT
Change the setting.
SET - UP
DATE / TIME
BEEP VOLUME
SHUTTER VOLUME
PLAYBACK VOLUME
LCD BRIGHTNESS
FORMAT
OFF
A Press n or o to select the menu.
B Press q.
Different type of screen appears
depending on selected item.
Settings
SET - UP
3
C Press n or o to change the setting.
D Press MENU/OK to confirm the setting.
A Press p or q to select the page.
B Press o to move to menu item.
111
[U SET-UP]
How to use the [SET-UP] menu (➝p.111)
[SET-UP] menu option
[
q [
[
112
Setting
Display
Factory default
Explanation
Page
IMAGE DISP.]
[CONTINUOUS]/[3
SEC]/[1.5 SEC]/
[ZOOM
(CONTINUOUS)]/
[OFF]
[1.5 SEC]
Sets the way for displaying the check image screen
(photograph result) after taking a picture. The color
tones in images recorded may differ from actual
color. Playback the recorded images to check them.
114
FRAME NO.]
[CONTINUOUS]/
[RENEW]
[CONTINUOUS]
Specifies whether frame numbers are assigned
consecutively from previous numbers or begin
again.
115
[ON]/[OFF]
[ON]
Specifies whether the AF-assist illuminator is [ON]
or [OFF].
33
116
AF ILLUMINATOR]
[
DIGITAL ZOOM]
[ON]/[OFF]
[OFF]
Specifies whether digital zoom is used.
[
EVF/LCD MODE]
[30fps]/[60fps]
[30fps]
Sets the screen display to the fine mode.
–
[
DATE/TIME]
–
–
Corrects the date or time.
24
[
BEEP VOLUME]
/
/
/[ OFF]
Sets the volume of the tone emitted when the
camera controls are used.
–
/
/
/[ OFF]
Sets the volume of the sound emitted when the
shutter operates.
–
[
SHUTTER
VOLUME]
[
PLAYBACK
VOLUME]
–
7
[
LCD
BRIGHTNESS]
–
0
[
–
–
FORMAT]
Sets the volume of playing back movie and voice
memo.
Sets the LCD monitor brightness.
Initializes a Memory Card or internal memory.
Select this menu to erase all the frames (files).
116
117
117
How to use the [SET-UP] menu (➝p.111)
Setting
[
Display
]
Factory default
[ENGLISH]
Explanation
Page
Specifies the language used for screen display.
25
Sets the time of turning camera off when camera is
not used.
118
Specifies the time difference settings.
118
[
AUTO POWER
OFF]
[5 MIN]/[2 MIN]/[OFF]
[2 MIN]
[
TIME
DIFFERENCE]
N/I
N
[
BACKGROUND
COLOR]
–
–
Specifies the colors of menu and background.
[
DISCHARGE]
–
–
Discharges Ni-MH batteries.
–
Specifies whether video output is set to [NTSC] or
[PAL].
–
–
Resets all the camera settings (other than the
[DATE/TIME], [TIME DIFFERENCE],
[BACKGROUND COLOR], and [VIDEO SYSTEM])
to the factory default values set at shipment. A
confirmation message appears when you press q.
To reset the camera settings, press p or q to
select [OK] and press MENU/OK.
–
[
VIDEO SYSTEM]
RESET]
[NTSC]/[PAL]
–
137
Settings
[
–
113
[U SET-UP]
[IMAGE DISP.]
Use this setting to specify the way for displaying the check
image screen (photograph result) after taking a picture.
How to use the [SET-UP] menu (➝p.111)
Z Enlarging images
ZOOM (CONTINUOUS
CONTINUOUS))
Navigation screen
(Current displayed image)
[CONTINUOUS]:
The results are always displayed after you shoot.
Press the MENU/OK to take another picture.
NEXT SHOOTING
[3 SEC]/[1.5 SEC]:
The image appears for about 3 or 1.5 seconds and is
then recorded.
A Turn to T or W to zoom in or out of an
image.
[ZOOM (CONTINUOUS)]:
The image appears enlarged. Use this mode to check
details of image.
B Press n, o, p, or q to display another
part of the image.
[OFF]:
The results are not displayed.
CAUTION
• The color tones in images displayed when [3 SEC] or
[1.5 SEC] is selected may differ slightly from those in
the images actually recorded.
• [IMAGE DISP.] cannot be used when [h LONG
PERIOD] (➝p.71) is set.
MEMO
When a result is displayed with [CONTINUOUS] set,
overexposed areas in an image can be checked by
pressing D.
C Press MENU/OK to take another picture.
The image is recorded automatically.
MEMO
• When ` quality setting is selected, the image cannot
be enlarged.
• Pressing DISP/BACK cancels the zoom setting.
• This function is disabled when setting the continuous
shooting.
Intelligent Face Detection
Images taken with the Intelligent Face Detection (➝p.29).
Press
(Intelligent Face Detection) to alternate
between the displayed faces. Turn the zoom lever to T or
W to zoom in or out the selected face. Press n, o, p
or q to display another part of the image.
114
How to use the [SET-UP] menu (➝p.111)
[FRAME NO.]
CHECK
Frame number
Use this function to specify whether frame numbers are
assigned consecutively from previous numbers or begin
again.
100 - 0001
File number
[CONTINUOUS] [RENEW]
A
B
* Formatted Memory Card or internal memory used for
both A and B.
[RENEW]:
Pictures are stored on each Memory Card beginning
with a file number 0001.
Each image will be numbered consecutively from the
last number used. So when recorded images in the
Memory Card are erased, the number of the erased
frame will not be used again.
The last 4 digits of the 7-digit number in the top right
corner of the screen are the file numbers, while the
first 3 digits show the directory number.
MEMO
• Setting this function to [CONTINUOUS] makes file
management easier as it makes sure that file names
are not duplicated when images are downloaded to a
PC.
• When the camera settings are [
RESET] (➝p.113),
the frame number setting ([CONTINUOUS] or
[RENEW]) is changed to [CONTINUOUS] and the
frame number itself does not return to 0001.
• In [CONTINUOUS] setting, images are stored
beginning from the highest file number on the current
Memory Card when the Memory Card already contains
image files with file numbers higher than the highest file
number on the last Memory Card.
• The displayed frame number may differ for images
photographed on other cameras.
Settings
[CONTINUOUS]:
Pictures are stored beginning from the highest file
number stored on the last Memory Card or internal
memory used.
Directory number
115
[U SET-UP]
How to use the [SET-UP] menu (➝p.111)
CAUTION
[DIGITAL ZOOM]
Use this function to shoot enlarged images than
maximum optical zoom scale.
Using the digital zoom allows you to enlarge your subject
and shoot it. However, it will lower your image quality. Set
the digital zoom when requiring it.
[PLAYBACK VOLUME]
AUTO
Zoom bar
Use this function to adjust volume while playing back
movie and voice memo.
VOLUME
7
Z Zoom bar display
SET
OFF
Optical zoom:12x
ON
Optical zoom:12x
Digital zoom:
approx. 5.7x
MEMO
When zooming changes between optical and digital, the
position of the “ ” indicator stops. Turn the Zoom lever
again to start the “ ” indicator moving again.
116
CANCEL
A Press n or o to adjust the volume.
The larger the number, the larger the
volume is emitted. 0 (zero) indicates a
sound deadening.
B Press MENU/OK to confirm the setting.
How to use the [SET-UP] menu (➝p.111)
[LCD BRIGHTNESS]
[FORMAT]
Use this function to adjust the screen brightness.
Initialize (format) the Memory Card or internal memory for
use with the camera.
LCD BRIGHTNESS
FORMAT
FORMAT OK?
0
ERASE ALL DATA
OK
SET
CANCEL
CANCEL
SET
B Press MENU/OK to confirm the setting.
A Press p or q to select [OK].
B Pressing MENU/OK initializes the Memory
Card or internal memory.
Settings
A Press n or o to adjust the screen
brightness.
The indicator moves to the + to display the
screen brightly or to the – to darken the
screen.
Place of initialize
[Y FORMAT OK?]:
Internal memory
[\ FORMAT OK?]:
Memory Card
CAUTION
• The Format function erases all the frames (files),
including protected frames (files).
Back up important frames (files) onto your PC or
another media.
• Do not open the battery cover during formatting. The
Memory Card or internal memory could be damaged.
117
[U SET-UP]
How to use the [SET-UP] menu (➝p.111)
[AUTO POWER OFF]
[TIME DIFFERENCE]
When this function is active and the camera remains
unused for 2 or 5 minutes, it turns camera off.
Use this function when you want to get the maximum
possible running time from your batteries.
Use this function when traveling to destinations in
different time zones. This function sets a time difference
relative to the date and time currently set. When this
setting is enabled, the specified time difference is applied
when pictures are taken.
CAUTION
The Auto power off function is disabled during slide show
(➝p.91), discharging rechargeable batteries (➝p.137),
and when a printer or a PC connection (➝p.121, 130) is
being used.
MEMO To restore power to the camera
Refer to “Turning On and Off” (➝p.21).
1
Use Time difference function.
SET - UP
ENGLISH
AUTO POWER OFF
2 MIN
TIME DIFFERENCE
HOME
BACKGROUND COLOR
LOCAL
DISCHARGE
VIDEO SYSTEM
NTSC
Press n or o to change between [N
HOME] and [I LOCAL].
To set the time difference, select [I LOCAL].
[N HOME]:Your home time zone
[I LOCAL]:Your destination time zone
118
How to use the [SET-UP] menu (➝p.111)
2
Move to [TIME DIFFERENCE] screen.
CHECK
Available time setting
–23:45 to +23:45 (in 15-minute increments)
SET - UP
ENGLISH
AUTO POWER OFF
2 MIN
TIME DIFFERENCE
HOME
BACKGROUND COLOR
LOCAL
DISCHARGE
VIDEO SYSTEM
NTSC
Press q.
3
In the time difference
setting, when you change to
the Shooting mode, I and
the date is displayed for 3
seconds, the date display
turns yellow.
12/ 31
12
31/ 2050
Set time difference.
11: 00 AM
11
CHECK
Upon returning from a trip, always change the time
difference setting back to [N HOME] and then check the
date and time again.
Settings
TIME DIFFERENCE
12 / 31 / 2050
10:00 AM
12 / 31 / 2050
10:00 AM
SET
MEMO
CANCEL
A Press p or q to select +/–, hour, and
minute.
B Press n or o to change the setting.
C Always press MENU/OK after the settings
are completed.
119
Connecting to a TV
When connecting to a TV, images can be displayed on wider screen. Using slide show function (➝p.91) together, you can have
fun with folks.
Plug the A/V cable (included) into
the A/V OUT (Audio/Visual
output) socket of the camera.
Video (yellow)
A/V OUT socket
To terminals
Audio (white)
Plug the other end of the cable into the
audio/video input socket on the TV.
AC-5VX (sold separately) and CP-04
(sold separately)
120
CAUTION
MEMO
Plug the A/V cable (included) and the AC power adapter
correctly and push them in each terminal.
• When connecting the A/V cable (included) to TV, the
camera’s screen is turned off.
• The image quality for movie playback is lower than for
still images.
• When connecting to a TV, even if you adjust the volume
from the [
PLAYBACK VOLUME], the TV volume
cannot be changed. Refer to the instructions provided
with your TV for more information on audio/video input
for your TV.
• Use the AC-5VX (sold separately) and CP-04 (sold
separately) when FinePix S1000fd is connected to a TV
for long periods. See “Notes and Cautions” (included)
for notes on the AC power adapter.
Connecting Camera Directly to Printer — PictBridge Function
When a printer that supports PictBridge is
available, images can be printed by
connecting the camera directly to the
PictBridge-compatible printer without a PC.
B Connect the camera to a printer and turn the printer on.
Press w for about 1 second to turn the camera on.
[
USB] appears on
the screen.
USB
Connecting to a printer
A Connect the camera to your printer using the USB
cable.
C The following screen appears on the screen after a
moment.
“Specifying images for
printing”
➝p.122
“Printing with DPOF setting”
➝p.123
PICTBRIDGE
TOTAL : 00000
00 SHEETS
FRAME
OK
SET
MEMO
Depending on the printer, some functions are disabled.
Camera Connection
;USB socket
AC-5VX (sold separately)
and CP-04 (sold separately)
MEMO
Use the AC-5VX (sold separately) and CP-04 (sold
separately) when FinePix S1000fd is connected to a
printer.
121
Connecting Camera Directly to Printer — PictBridge Function
Specifying images for printing
([PRINT WITH DATE] / [PRINT
WITHOUT DATE])
PRINT THESE FRAMES
TOTAL : 9 SHEETS
PICTBRIDGE
TOTAL : 00002
YES
D Press MENU/OK again to download the
data to the printer and start printing the
specified number of prints.
02 SHEETS
FRAME
OK
CANCEL
SET
MEMO
A Press p or q to display the frame (file)
for specifying PRINT setting.
B Press n or o to set a value.
Up to 99 sheets are printed.
To specify more PRINT settings, repeat steps A and B.
C Press MENU/OK to display the confirm
setting.
Even if MENU/OK is pressed with total number of images set
at 0 (zero), the screen printing once appears on the screen.
Press MENU/OK again and printing starts.
MEMO Printing with date
PICTBRIDGE
PRINT WITH DATE
PRINT WITHOUT DATE
PRINT DPOF
A Press DISP/BACK to
display the setting
display.
B Press n or o to select
[PRINT WITH
DATEE].
C Press MENU/OK.
CAUTION
[PRINT WITH DATEE] is not available when the camera
is connected to a printer that does not support date
printing.
122
Printing with DPOF setting
[u PRINT DPOF]
PRINT DPOF OK?
TOTAL : 9 SHEETS
PICTBRIDGE
PRINT WITH DATE
PRINT WITHOUT DATE
PRINT DPOF
YES
CANCEL
D Press MENU/OK again to download the
data to the printer and start printing the
specified frames (files) continuously.
A Press DISP/BACK to open the menu.
CHECK
To select [uPRINT DPOF], the DPOF settings must be
specified on FinePix S1000fd beforehand (➝p.91).
B Press n or o to select [u PRINT DPOF].
Even when [WITH DATEE] is specified in the DPOF
settings (➝p.91), the date is not inserted on printers that
do not support date printing.
Continued Q
Camera Connection
C Press MENU/OK to display the confirm
setting.
CAUTION
123
Connecting Camera Directly to Printer — PictBridge Function
MEMO
MEMO
PRINTING
DPOF setting can be specified for images on internal
memory.
CAUTION
CANCEL
Press DISP/BACK to cancel the printing.
Depending on the printer, the printing may not be
canceled immediately or printing may stop midway
through.
When printing stops midway, briefly turn the camera off
and then on again.
Disconnecting the printer
A Check that [PRINTING] is not displayed on the
camera’s screen.
B Turn the camera off. Unplug the USB cable.
124
• In PictBridge function, images photographed on other
than a camera may not be printed.
• The camera cannot be used to specify printer settings
such as the paper size and print quality.
• Please connect the AC Power Adapter AC-5VX (sold
separately) and DC Coupler CP-04 (sold separately) to
your camera.
• Use internal memory or a Memory Card that was
formatted on FinePix S1000fd.
• Movies cannot be printed.
• Images photographed with a camera other than FinePix
S1000fd may not be printed.
Installation on a Windows PC
Pre-installation checklist
Z Hard ware (software) requirements and recommended system
To run this software, you must have the hardware and software described below. Check your system before you begin the
installation.
requirement
Recommendation
Windows XP
Windows Vista
Operating System*1
Windows 98 SE
Windows Millennium Edition (Windows Me)
Windows 2000 Professional*2
Windows XP Home Edition*2
Windows XP Professional*2
Windows Vista*2
CPU
200 MHz Pentium minimum
(Windows XP/Vista users: 800MHz Pentium 4 or better recommended)
2 GHz Pentium
4 or better
3 GHz Pentium
4 or better
RAM
128 MB minimum (512 MB minimum for Windows Vista)
512 MB or better 1 GB or better
Hard disk space
Amount required for installation: 450 MB minimum
Amount required for operation: 600 MB minimum
2 GB or better
800 × 600 pixels or better, 16-bit color or better
1024 × 768 pixels or better,
Highest (32 bit)
Display
15 GB or better
CAUTION
•
•
•
•
Additional USB interface board is not guaranteed.
Windows 95, Windows 98 and Windows NT cannot be used.
Operation is not guaranteed on home-built PCs or on PCs running updated operating system software.
When you reinstall or remove FinePixViewer, the Internet menu and your user ID and password for the FinePix Internet Service
are deleted from your PC. Click the [Register now] button, enter your registered user ID and password and download the menu
again.
Software Installation
*1 Models with one of the above operating systems pre-installed.
*2 When you install the software, login using a system administrator account (e.g. “Administrator”).
125
Installation on a Windows PC
Do not connect the camera to your PC
until the software installation is
completed.
1
Install FinePixViewer as instructed by the
on-screen instructions.
For Windows Vista users:
When loading the bundled CD-ROM on your PC, the
[AutoPlay] window may appear. In this case, click
[SETUP.exe].
When [User Account Control] window appears, click [Allow].
2
Launching the installer manually
A Double-click the [My Computer] icon.
* Windows XP users should click [My Computer] in the [Start]
menu.
Windows Vista users should click [Computer] in the [Start]
menu.
B Right-click [FINEPIX] (CD-ROM drive) in the [My
Computer] window (Windows Vista users: in the
[Computer] window) and select [Open].
C Double-click [SETUP] or [SETUP.exe] in the CD-ROM
window.
* The way file names are displayed differs as described below
depending on your PC settings.
-File extensions (3-letter suffixes indicating the file type)
may be shown or hidden. (e.g. Setup.exe or Setup)
-Text may be shown normally or all in uppercase (e.g. Setup
or SETUP).
126
Install DirectX as directed by the on-screen
instructions and then restart your PC. If the
latest version of DirectX is already installed
on your PC, this installation is not
performed.
CAUTION
• If the latest version of DirectX or Windows Media Player
has not been installed, each software will be installed,
and then the PC will restart.
• Do not remove the CD-ROM during this procedure.
3
After restarting the PC, a message appears
stating [Installation of the FinePixViewer
has been completed]. Remove the CD-ROM
from your PC.
Installation on a Mac OS X
Pre-installation checklist
Z Hardware and software requirements
To run this software, you must have the hardware and software described below. Check your system before you begin the
installation.
Compatible Mac*1
Power Macintosh G3*2, PowerBook G3*2,
Power Macintosh G4, iMac, iBook,
Power Macintosh G4 Cube, PowerBook G4, Power Macintosh G5,
MacBook, MacBook Pro, or Mac mini
Operating System
Mac OS X (compatible with version 10.3.9 to 10.4.10)
RAM
256 MB minimum
Hard disk space
Amount required for installation: 200 MB minimum
Amount required for operation: 400 MB minimum
Display
800 × 600 pixels or better, at least 32,000 colors
*1
*2
PowerPC, Intel processor loaded
Models with a USB port as a standard feature
CAUTION
Continued Q
Software Installation
• Connect the camera directly to the Macintosh using the USB cable (included). The software may not operate correctly if you use
an extension cable or connect the camera via a USB hub.
• Push the USB connector fully into the socket to ensure that it is securely connected. The software may not operate correctly if the
connection is faulty.
• Additional USB interface board is not guaranteed.
127
Installation on a Mac OS X
128
1
Turn your Macintosh on and start up Mac
OS X. Do not launch any other applications.
2
When the bundled CD-ROM is loaded into
the CD-ROM drive, the [FinePix] icon
appears. Double-click the [FinePix] icon to
open the [FinePix] volume window.
3
4
Double-click on [Installer for MacOSX].
The Installer setup dialog appears. Click the
[Installing FinePixViewer] button.
CAUTION
For more information on what is installed, click the [Read
Me First] button and [Using FinePixViewer] button.
5
The [Authenticate] dialog appears.
Enter the name and password for the
administrator account and then click the
[OK] button.*
* The administrator account is the user account used for
Mac OS X installation and you can confirm the user
account in the Accounts dialog in the System
Preferences.
6
Install FinePixViewer as directed by the onscreen instructions.
7
The [FinePixViewer installation completed]
message dialog appears. Then click exit
button and close it.
CAUTION
When Safari is used as the Web browser, a message may
be displayed and the CD-ROM may not be removed. If
this happens, click the Safari icon in the Dock to make
Safari the active application and then select [Quit Safari]
in the [Safari] menu to shut down Safari.
8
Launch [Image Capture] from the
[Applications] folder.
9
Change the Image Capture settings.
Select [Preferences...] from the [Image
Capture] menu.
10 Select [Other...] from [When a camera is
connected, open].
11 Select [FPVBridge] from [FinePixViewer]
folder in the [Applications] folder and click
the [Open] button.
12 Select [Quit Image Capture] menu in the
[Image Capture] menu.
Software Installation
129
Connecting to a PC
By connecting the camera to a PC, your system can be
expanded to fill a wide range of uses. Using
“FinePixViewer” performs images saving, browsing and
file management etc.
FinePixViewer Overview
Enables importing images, managing files and folders,
and ordering prints using the internet (only Windows
users).
CAUTION
• Do not format the Memory Card in the camera on the PC.
• Use the Memory Card with images taken by a
FUJIFILM Digital camera.
B Connect the camera to your PC using the USB cable
(included).
CAUTION
The Windows CD-ROM may also be required during
installation. In this event, change CD-ROMs as directed
by the on-screen instructions.
Refer to Software
Installation (➝p.125, 127)
the first time you connect
the camera to your PC.
Install the software first. Do
not connect the camera to
the PC before installing all
the software.
;USB socket
CD-ROM
(Software for FinePix)
A Insert the Memory Card with images into the camera
(➝p.18).
You can use the xD-Picture Card and the SD
Memory Card with the FinePix S1000fd.
In this Owner’s Manual, these cards are expressed as
“Memory Card”.
AC-5VX (sold separately)
and CP-04 (sold separately)
C Press w for about 1 second to turn the
camera on in Playback mode.
D Set your PC
MEMO
In Windows, if FinePixViewer is already installed, the
driver will be set automatically. No action is required.
130
CAUTION
• FinePix S1000fd is compatible with PTP (Picture
Transfer Protocol)/MTP (Media Transfer Protocol). A
PTP/MTP-compatible camera is a camera that can
recognize the PC and printer automatically when
connected.
• Do not disconnect the USB cable (included) when the
camera is communicating with a PC. If the USB cable
(included) is disconnected during communication, the
files on the Memory Card or internal memory may be
damaged.
• In Mac OS X, you must set automatic setup the first time
you connect the camera to your PC.
• When the camera and PC are exchanging data, the
indicator lamp blinks alternately green and orange.
• Auto power off is disabled during USB connection.
• Before replacing the Memory Card, always disconnect
the camera from the PC.
• The camera and PC may be exchanging data even
when [Copying] disappears from your PC screen.
Before disconnecting the USB cable (included), always
check that the indicator lamp is off.
• Always use FinePixViewer to transfer images with voice
memos to a PC.
• The cost of an Internet provider for connecting to the
internet is the user’s responsibility.
• When using FinePixViewer to save images on a data
server (network), FinePixViewer may not run as it would
in a standalone PC environment.
• Always use the FUJIFILM AC Power Adapter AC-5VX
(sold separately) and DC Coupler CP-04 (sold
separately). If the camera suddenly loses power during
data exchange, data exchange will not be performed
correctly, and the Memory Card or internal memory
could be damaged.
• Make sure that the USB cable (included) is connected
correctly and securely.
• Connect the camera directly to the PC using the USB
cable (included). The software may not operate
correctly when you use an extension cable, or if you
connect the camera via a USB hub.
• When your PC has more than one USB port, the
camera can be connected to either port.
• When Windows 98 SE is used, the supplied software
must be installed first before connecting the camera to
a PC using the USB cable. The PC will not recognize
the camera if it is connected before installation.
• A memory Card, the internal memory, data in a Memory
Card or data in the internal memory could be damaged
if any of the following are performed;
- the USB cable is disconnected
- ON/OFF switch or buttons are pressed
Continued Q
Software Installation
CAUTION
131
Connecting to a PC
The following steps differ depending on the
PC’s operating system (Windows XP/Vista and
Mac OS X case)
When your PC recognizes the camera automatically,
FinePixViewer automatically starts up and the Save
Image Wizard window (Save Image dialog box) appears.
Follow the instructions provided on screen to save the
images. To proceed without saving the images, click the
[Cancel] button.
CAUTION
When there are many images stored on a Memory Card,
it takes a while to display on the screen of your PC. Also,
it may take a while to import images or you may be unable
to save images. In this case, use an Image Memory Card
Reader.
MEMO
• You can only see images saved on a PC. Save images
on a PC.
• If you cancel saving by clicking the [Cancel] button,
slide the power swich to turn off the camera and then
disconnect it from the PC.
• When the camera is connected to your PC,
FinePixViewer automatically starts up by the function of
Exif Launcher, which is installed in FinePixViewer.
Proceed to “Using FinePixViewer” (➝p.133).
132
CAUTION (MAC OS X)
If FinePixViewer does not start up automatically, the
software may not be installed correctly. Set your PC again
after disconnecting the camera and restart.
CAUTION (MAC OS X)
Note on disconnecting the camera
• Close all files in the camera, and make sure the camera
is not exchanging data.
• The camera and PC may be exchanging data even
when [Copying] disappears from your PC screen,
especially in the case of copying large data amounts.
Do not disconnect the USB cable (included),
immediately after this message has disappeared.
Always check that the indicator lamp is off first before
disconnecting.
Using FinePixViewer
Mastering FinePixViewer
For all information on FinePixViewer functions, refer to
[How to Use FinePixViewer] in the Help menu for details.
The following software is to be uninstalled:
•
•
•
•
FinePixViewer
FinePix Resource
FinePix Studio*
RAW FILE CONVERTER LE*
* May not have been installed depending on the
operating system.
• What is explained in [How to Use FinePixViewer]...
[How to Use FinePixViewer] covers a range of topics,
including batch processing and ordering prints.
Example: Looking up slide shows
A Click [How to Use FinePixViewer] in the FinePixViewer
Help menu.
B Click [Basic Operation] and then click [Slide Show] in
the menu that appears.
C The [Slide Show] information appears. Press the [<<<]
key to view the previous page or the [>>>] key to view
the next page.
Uninstalling the software
5
5
To remove the driver
software
D When the message appears, click the [OK] button.
Check your selection carefully since the process
cannot be canceled once you click the [OK] button.
Windows
A Check that the camera is not connected to the PC.
B Quit all currently running applications.
C The steps for uninstalling software differ depending on
the operating system. Follow the steps for each
operating system to uninstall the software listed below.
Software Installation
Only perform this operation when you no longer require
the installed software or when the software was not
installed correctly.
To remove FinePixViewer
Macintosh
Quit FinePixViewer. Then drag the installed
FinePixViewer folder to the Trash and select [Empty
Trash] in the [Finder] menu.
133
System Expansion Option
By using FinePix S1000fd together with other optional FUJIFILM products, your system can be expanded to fill a wide range
of uses.
Accessory availability may vary by country. Please check with your local Fujifilm representative to confirm product availability.
Z Audio/Visual
Z Image
output
TV monitor
(commercially available)
input/output to the PC
USB
Personal Computer
(commercially available)
Audio/Visual
output
xD-Picture Card
Z Printing
PC Card Adapter DPC-AD
(PC card slot)
* This will not work with an
SD Memory Card.
USB
SD/SDHC Memory Card
PictBridge-compatible printer
(commercially available)
Printer
(commercially available)
134
CompactFlash™
Card Adapter DPC-CF
(CF card slot)
* This will not work with an SD
Memory Card.
Accessories Guide
Visit the FUJIFILM web site for the latest information on camera accessories.
http://www.fujifilm.com/products/digital_cameras/index.html
Accessory availability may vary by country. Please check with your local Fujifilm representative to confirm product availability.
• xD-Picture Card
Use the following xD-Picture Cards:
256MB/512MB/1GB/2GB
There are two types of xD-Picture Card: standard type and Type M (containing “M” in the model
number, such as DPC-M1GB).
FinePix S1000fd is compatible with Type M, however they may not be compatible depending on the
device used (Image Memory Card Reader, etc.).
• AC Power Adapter AC-5VX
Use the AC-5VX when taking pictures or play back images for long periods or when FinePix
S1000fd is connected to a PC.
* The shape of the AC power adapter, the plug, and power outlet depend on the country.
• DC Coupler CP-04
Use the CP-04 with AC-5VX when taking pictures or playback images for long periods or
when FinePix S1000fd is connected to a PC.
• CompactFlash™ Card Adapter DPC-CF
Loading an xD-Picture Card into this adapter allows you to use the card as a CompactFlash card (Type
s).
* This is not compatible with the SD Memory Card.
Appendices
• PC Card Adapter DPC-AD
The PC Card Adapter allows the xD-Picture Card and SmartMedia to be used as a PC Card Standard
ATA-compliant (PCMCIA 2.1) PC card (Type u).
-Compatible with xD-Picture Card of 16 MB to 512 MB, and SmartMedia of 3.3 V, 2 MB to 128 MB.
* This is not compatible with the SD Memory Card.
DPC-
CF
CO
MPAC
CARD
TFLA
ADAP
SH TM
TER
for
xD-P
ictur
e Card
135
Using Your Camera Correctly
Read this information and the “Safety Notes” (➝ “Notes
and Cautions” (included)), to make sure you use your
camera correctly.
Z Places to Avoid
Do not store or use the camera in the following types of
locations:
• In the rain or in very humid, dirty, or dusty places
• In direct sunlight or in places subject to extreme
temperature rises, such as in a closed car in summer
• Extremely cold places
• Places with strong vibration
• Places with smoke or steam
• Places subject to strong electric magnetic fields (such
as near broadcasting tower, power lines, radar, motors,
transformers, magnets, etc.)
• In contact with chemicals such as pesticides
• Next to rubber or vinyl products
Z Damaged by Water or Sand
FinePix S1000fd can be damaged on the inside and
outside by water and sand. When you are at the beach or
close to water, make sure that the camera is not damaged
by water or sand. Take care not to place the camera on a
wet surface.
Z Damaged by Condensation
If the camera is carried from a cold location into a warm
place, water droplets (condensation) may form on the
inside of the camera or on the lens. When this occurs, turn
the camera off and wait an hour before using the camera.
Condensation may also form on the Memory Card. In this
event, remove the Memory Card and wait a short time.
136
Z When the Camera is Not Used or is stored Periods
of Time
If you do not intend to use the camera for a long period of
time, remove the batteries and the Memory Card.
Z Cleaning Your Camera
• Use a blower brush to remove any dust on the lens,
LCD monitor or viewfinder, and then gently wipe the
camera with a soft, dry cloth. If any soil remains, apply
a small amount of lens cleaning liquid to a piece of
FUJIFILM lens cleaning paper and wipe gently.
• Do not scratch hard objects against the lens, LCD
monitor or viewfinder.
• Clean the body of the camera with a soft, dry cloth. Do
not use volatile substances or cleaning products these
items can cause damage.
Z Using the Camera When Traveling
When traveling overseas, do not place your camera in the
check-in baggage. Baggage can be subjected to violent
shocks, and the camera may be damaged inside or
outside.
Discharging rechargeable batteries
The Discharging rechargeable batteries function can only
be used with Ni-MH batteries.
The Discharging rechargeable batteries function should
not be used with alkaline batteries or lithium batteries as
it will completely drain the battery charge.
Use the Discharging rechargeable batteries function in
the following situations:
• When the batteries only last for a short time after being
charged normally
• When the batteries have not been used for a long period
• When you purchase new Ni-MH batteries
Do not use the Discharging rechargeable batteries
function while using the AC power adapter and DC
coupler. In these situations, the Ni-MH batteries will not
be discharged due to the external power supply.
D Press q to display the [SET-UP] menu.
E Press p or q to select
F Press n or o to select [
DISCHARGE].
DISCHARGE
DISCHARGE OK?
IT MAY TAKE A WHILE
FOR DISCHARGING
OK
To discharge rechargeable batteries:
CANCEL
SET
SET - UP
AUTO POWER OFF
TIME DIFFERENCE
BACKGROUND COLOR
DISCHARGE
VIDEO SYSTEM
.
ENGLISH
2 MIN
NTSC
G Press q.
H Press MENU/OK.
B Press MENU/OK to display the menu on
the screen.
C Press n or o to select [U SET-UP].
I Press p or q to select [OK].
J The screen changes and discharging
begins. When the battery level indicator
blinks red and discharging ends, the
camera turns off.
Appendices
A Press w to turn the camera on.
CAUTION
To cancel discharging, press DISP/BACK.
137
Notes on the xD-Picture Card™, the SD Memory Card and the Internal Memory
Z Handling Memory Card
• When inserting the Memory Card into the camera, hold
the Memory Card straight as you push it in.
• Never remove the Memory Card or turn the camera off
during data recording or erasing (Memory Card
formatting) as this could be damaged to the Memory
Card.
• The use of xD-Picture Cards is recommended with
FinePix S1000fd.
The recording quality cannot be guaranteed when xDPicture Cards other than those manufactured by
FUJIFILM are used.
• The Memory Card may feel warm when it is removed
from the camera after taking pictures. This is normal.
• Do not put labels on the Memory Card. Peeling labels
can cause the camera not to work properly.
MEMO Type M and H of xD-Picture Card
• Type M
There are two types of Memory Card: standard type and
Type M (containing “M” in the model number, such as
DPC-M2GB).
FinePix S1000fd is compatible with Type M.
• Type H
Type H and M share the same compatibility.
• Usable USB drive
Type H cannot be used with xD-Picture Card USB
drive DPC-UD1, while Type M can.
138
Z Internal Memory
• Images held in the camera’s internal memory may be
corrupted or erased due to problems such as camera
faults. Save your important data to another media (i.e.,
DVD-R, CD-R, CD-RW, hard disk, etc.).
• Data stored in the camera’s internal memory cannot be
guaranteed in the event that the camera is submitted for
repairs.
• When the camera is repaired, any data stored in the
camera’s internal memory is subject to checking by the
repairer.
Z Using Memory Card or Internal Memory with a PC
• When taking pictures using a Memory Card or internal
memory that has been used on a PC, reformat the
Memory Card using your camera.
• When formatting, a directory (folder) is created. Image
data is then recorded in this directory.
• Do not change or delete the directory (folder) or file
names on the Memory Card or internal memory
because this will make it impossible to use the Memory
Card or internal memory in your camera.
• Always use the camera to erase image data.
• To edit image data, copy or transfer the image data to
the PC and edit the copied or transferred data.
Warning Displays
The table below lists the warnings that are displayed on the screen.
Warning Displayed
(Lit red)
V (Blinking red)
Explanation
Remedy
Load new or fully charged batteries.
There is a strong likelihood of camera shake
because the shutter speed is slow.
Use flash photography. A tripod may be
recommended, depending on the scene and mode.
The AF (autofocus) cannot work effectively.
• If the image is too dark, take the picture at a
distance of around 2 m (6.6 ft.) from the subject.
• Use AF lock to take the picture (➝p.32).
• Select Macro mode when taking close-up shots.
The camera cannot shoot the picture at the correct
brightness due to too bright or dark shooting
condition.
The picture can be taken, but the correct brightness
(exposure) will not be obtained.
[FOCUS ERROR]
• Camera malfunction or fault.
• Turn the camera on again, taking care not to touch
the lens.
[ZOOM ERROR]
• You are touching the autofocus ring.
• Do not hold the autofocus ring. The lens will
automatically refocus when you release the
autofocus ring.
Memory Card is not inserted when transferring
images.
Insert a Memory Card.
{
*The shape of the AF
frame differs depending
on the setting in the
[SHOOTING MENU].
Aperture/
Shutter speed display
(Lit red)
[NO CARD]
Continued Q
Appendices
The batteries are low or completely out of charge.
139
Warning Displays
Warning Displayed
[CARD NOT
INITIALIZED]
[CARD ERROR]
[\ MEMORY FULL]
[Y MEMORY FULL]
[WRITE ERROR]
[PROTECTED CARD]
Explanation
• The Memory Card or internal memory is not
formatted.
• The Memory Card was formatted on a PC.
• The Memory Card contact area is soiled.
• Camera fault.
• Contact your FUJIFILM dealer.
• The Memory Card contact area is soiled.
• The Memory Card format is incorrect.
• Wipe the contact area on the Memory Card with a
soft, dry cloth. It may be necessary to format the
Memory Card (➝p.117). If the message still
appears, replace the Memory Card.
• Camera fault.
• Contact your FUJIFILM dealer.
• The Memory Card is damaged.
• Inserted Memory Card is not compatible with your • Insert a compatible Memory Card that is operationchecked at FUJIFILM Corporation.
camera.
The internal memory or Memory Card is full.
140
Erase some images in internal memory or Memory
Card (➝p.41), or use a Memory Card that has ample
free space.
• The data could not be recorded due to an Memory • Re-insert the Memory Card or turn the camera off
Card error or a connection error between the
and then on again. If the message still appears,
Memory Card and camera.
contact your FUJIFILM dealer.
• The image cannot be recorded as it is too large to • Use a new Memory Card.
fit in the available space on the Memory Card.
• The Memory Card or internal memory is not
• Format the Memory Card or internal memory on
formatted.
the camera (➝p.117).
The SD Memory Card switch is slide to the “Lock”
side.
[INTERNAL MEMORY The data could not be recorded or copied since the
IS FULL
internal memory is full.
INSERT A NEW CARD.]
[BUSY]
Remedy
• Format the Memory Card or internal memory on
the camera (➝p.117).
• Format the Memory Card on the camera.
• Wipe the contact area on the Memory Card with a
soft, dry cloth. It may be necessary to format the
Memory Card (➝p.117). If the message still
appears, replace the Memory Card.
The timing for recording was incorrect because the
Memory Card was formatted on a PC.
Unlock the protection by sliding it back (➝p.19)
Erase some images from the internal memory
(➝p.41), or use a Memory Card that has ample free
space.
Use a Memory Card that was formatted on the
camera.
Warning Displayed
Explanation
The frame number has reached 999-9999.
No more pictures can be taken.
[FRAME NO. FULL]
Remedy
A Insert a formatted Memory Card into the camera.
B Set [RENEW] as the [FRAME NO.] setting in the
[U SET-UP] menu (➝p.115).
C Start taking pictures (The frame number starts
from “100-0001”).
D Set [CONTINUOUS] as the [FRAME NO.]
setting in the [U SET-UP] menu.
• The played back file was not recorded correctly.
• The Memory Card contact area is soiled.
[READ ERROR]
• This file cannot be played back.
• Wipe the contact area on the Memory Card with a
soft, dry cloth. It may be necessary to format the
Memory Card (➝p.117). If the message still
appears, replace the Memory Card.
• Camera fault.
• Contact your FUJIFILM dealer.
• An attempt was made to play back the image or the • The movie and image cannot be played back.
movie that was not recorded on this camera.
[TOO MANY FRAMES]
An attempt was made to show 5,000 or more image No more than 4,999 images can be shown by date
by date sorting.
sorting.
• An attempt was made to erase a protected file.
[PROTECTED FRAME]
[\ NO IMAGE]
[Y NO IMAGE]
[` CAN NOT TRIM]
• The voice memo file is faulty.
• Camera fault.
• The voice memo cannot be played back.
• Contact your FUJIFILM dealer.
An attempt was made to transfer images from the
Memory Card or internal memory that memory was
empty.
It is impossible to copy.
An attempt was made to trim a 0.3M image.
The image cannot be trimmed.
Appendices
[# ERROR]
• An attempt was made to add a voice memo to
protected file.
• An attempt was made to rotate a protected file.
• Protected files cannot be erased. Remove the
protection (➝p.98).
• Protected files cannot be added to voice memos.
Remove the protection (➝p.98).
• Protected files cannot be rotated. Remove the
protection (➝p.98).
Continued Q
141
Warning Displays
Warning Displayed
[CAN NOT TRIM]
[DPOF FILE ERROR]
[CAN NOT SET DPOF]
[r CAN NOT SET
DPOF]
Explanation
Remedy
• An attempt was made to trim an image shot using The image cannot be trimmed.
a camera other than FinePix S1000fd.
• The image is damaged.
Prints were specified for 1000 or more frames in the The maximum number of frames for which prints can
DPOF frame settings.
be specified on the same Memory Card is 999.
Copy the images for which you want to order prints
onto another Memory Card and then specify the
DPOF settings.
An attempt was made to specify DPOF settings for a DPOF printing cannot be used with this image
movie or an image that is not supported by DPOF. format.
[CAN NOT ROTATE]
An attempt was made to rotate a movie or an image These images cannot be rotated by image formats.
[r CAN NOT ROTATE] shot using a camera other than FinePix S1000fd.
[CANNOT DETECT]
[
CANNOT DETECT]
[r CANNOT DETECT]
[
CANNOT DETECT]
[COMMUNICATION
ERROR]
An attempt was made to correct the red-eye effect in Red-eye removal cannot be used with these image
images taken with [FACE DETECTION] set to [OFF], formats.
movies, images taken by another camera, or images
not allowing red-eye removal.
The camera is not connected to a PC or printer.
• Check that the USB cable is connected correctly.
• Check that your printer is turned on.
Displayed for PictBridge.
• Check that the printer is not out of paper or out of
ink.
• Turn the printer off briefly and then turn it back on.
• Refer to the user manual supplied with your
printer.
Displayed for PictBridge.
Check that the printer is not out of paper or out of ink.
Printing automatically restarts when the error is
cleared. If the message still appears after checking,
press MENU/OK to restart printing.
[PRINTER ERROR]
[PRINTER ERROR
RESUME?]
142
Warning Displayed
Explanation
Displayed for PictBridge.
[CANNOT BE PRINTED]
Remedy
• Refer to the user manual for the printer being used
and check whether the printer supports the JFIFJPEG or Exif-JPEG image format. If not, the printer
cannot print the images.
• Movies cannot be printed.
• Was the image data photographed using FinePix
S1000fd?
You may not be able to print some images
photographed on other cameras.
Appendices
143
Troubleshooting
Z Getting ready
Matters
Problems
Possible causes
The batteries have run out.
The batteries are loaded backward.
Nothing happens
when sliding the
The AC power adapter and DC coupler are
ON/OFF switch or not connected correctly.
pressing w.
The camera has been left for a long period
with batteries, AC power adapter and DC
coupler removed.
Batteries and
power supply
Batteries run out
quickly.
Solutions
Load new or fully charged batteries.
Load the batteries in the corrected
direction.
16
Connect the AC power adapter and DC
coupler correctly.
–
Load the batteries or connect the AC
power adapter and DC coupler, and wait a 15, 21
short time before turning the camera on.
Camera is used in extremely cold
conditions.
Put the batteries in your pocket or another
warm place to heat it and then load it into 15, 17
the camera just before you take a picture.
The battery terminals are soiled.
Wipe the battery terminals with a clean,
dry cloth.
144
17
Same batteries have been used for a long The batteries can no longer be recharged.
15, 17
period.
Load a new batteries.
The rechargeable batteries (if used) have Use the rechargeable battery discharging
become deactivated, or the battery
function to restore the rechargeable
capacity has diminished due to the
batteries to full capacity.
memory effect.
Power cuts out
during operation.
Page
15, 17
The batteries have run out.
Load new or fully charged batteries.
The AC power adapter and DC coupler are Connect the AC power adapter and DC
not connected correctly.
coupler correctly.
137
15, 17
–
Z Setting menu etc.
Matters
LCD monitor
display
Problems
Screens are not
displayed in
English.
Possible causes
Solutions
Page
A language other than English is selected Select [ENGLISH].
in the [
] setting in the [SET-UP]
menu.
25
Z Shooting
Matters
Basic operations
Problems
No photograph is
taken when
pressing the
shutter button.
Possible causes
Solutions
Page
The Memory Card or internal memory is
full.
Insert a new Memory Card or erase some
18, 41
unnecessary frames.
The Memory Card or internal memory is
not formatted.
Format the Memory Card or internal
memory on the camera.
111,
117
The Memory Card contact area is soiled.
Wipe the Memory Card contact area with a
soft, dry cloth.
18,
138
The Memory Card is damaged.
Insert a new Memory Card.
The batteries have run out.
Load new or fully charged batteries.
The Auto power off function has turned the Turn the camera on.
camera off.
The screen
darkens after
taking a picture.
Focusing
21
The screen may darken for charging flash.
Wait a short time.
66
You took a close-up shot without selecting Select Macro mode.
Macro mode.
63
You photographed scenery with Macro
mode selected.
Cancel Macro mode.
63
You are shooting a subject that is not
suited to autofocusing (➝p.33).
Use AF/AE lock to take the picture.
32
Continued Q
Troubleshooting
Camera has
difficulty in
focusing on the
subject.
You took pictures with flash.
18
15, 17
145
Troubleshooting
Matters
Problems
Solutions
Intelligent Face
Detection
The Shooting mode is set to ,, .,
,
or
.
Macro
Cannot set the
camera to Macro
(close-up) mode.
The Shooting mode is set to H, ,, .,
/,
,
,
,
,
or
.
Cannot use the
flash.
Flash
Photographed images
,
Page
Change the Shooting mode.
48
Change the Shooting mode.
48
The shutter button was pressed while the Wait until the charging is completed before
flash was charging.
pressing the shutter button.
66
The flash is not popped up.
64
The Shooting mode is set to
,
or
.
Pop up the flash.
, ,,
, Change the Shooting mode.
48
The batteries have run out.
Load new or fully charged batteries.
Continuous shooting is selected.
Set continuous shooting to OFF.
69
> Super macro mode is selected.
Cancel > Super macro mode.
63
The flash settings The Shooting mode is set to anything other
are restricted and than H and N.
cannot be
selected.
The flash settings are restricted because
the camera settings are tailored to the
scene being shot. Change the Shooting
mode for a wider range of flash settings.
The playback
image is dark
even though the
flash was used.
Move to within the effective flash range
before taking the picture.
The image is
blurred.
146
Possible causes
Cannot set
Intelligent Face
Detection.
The subject is too far away.
15, 17
48, 65
152
Your finger was covering the flash.
Hold the camera correctly.
27
The lens is dirty.
Clean the lens.
136
AF frame (lit red) and { appeared when Check the focus on the subject and take
taking pictures.
pictures.
appeared when taking pictures.
It may cause camera shake. Hold the
camera steadily.
The picture was taken with a slow shutter This is a characteristic of CCDs and does
There is speckling
speed (long exposure) in a highnot indicate a camera fault.
on the image.
temperature environment.
27,
31,
139
28,
139
–
Matters
Problems
Possible causes
Solutions
AC power adapter and DC coupler were Connect or disconnect the AC power
connected or disconnected during turning adapter and DC coupler only when the
Photographed
the camera on.
camera is off. Failing to turn the camera off
Recording images images or movies
first can result in damage to the Memory
are not recorded.
Card or malfunctions during PC
connection.
Continuous
shooting
Only 1 frame can A picture is taken using self-timer when
be shot even
setting [LONG PERIOD] continuous
though continuous shooting mode.
shooting mode
was set.
Only 1 frame can be shot when using
[LONG PERIOD] continuous shooting
mode and Self-timer mode together.
Page
–
69, 71
Troubleshooting
147
Troubleshooting
Z Playing back
Matters
Problems
Possible causes
The camera volume is set too low.
Playing back
movie / voice
memo
The camera does
The microphone was blocked during
not emit any
shooting/recording.
sound.
There is something covering the speaker
during playback.
Erasing [FRAME] Some frames may be protected.
does not erase the
frame.
Erasing
Frame No.
148
Solutions
103,
110,
111,
116
Take care not to block the microphone
during shooting/recording.
12,
101,
107
Make sure that the speaker is uncovered.
12,
102,
110
Unprotect frames using the camera on
which the protection was first applied.
98
Erasing [ALL
FRAMES] does
not erase all the
frames.
You opened the battery cover without
[CONTINUOUS]
turning the camera off when replacing the
in the frame
batteries or Memory Card.
number setting
does not function.
Page
Adjust the volume.
Always turn the camera off when replacing
the batteries or Memory Card. Opening the
battery cover without turning the camera
off may cause the frame number memory
to not function.
21
Z Connecting
Matters
Problems
Possible causes
The camera is not connected to the TV
correctly.
Connecting to TV
The included A/V cable was connected
There is no image during movie playback.
or sound on the
“TV” is selected as the TV input.
TV.
The video output setting is incorrect.
The TV image is
black and white.
PC does not
Connecting to PC recognize the
camera.
Connecting to
printer
Cannot print with
PictBridge.
Solutions
Connect the camera and TV correctly.
After the movie playback mode is stopped,
connect the camera and TV correctly.
Set the TV input to “VIDEO”.
Change the setting to [NTSC] or [PAL].
The TV volume is turned down.
Adjust the volume.
The video output setting is incorrect.
Change the setting to [NTSC] or [PAL].
The USB cable is not correctly connected Set up the camera, and connect the USB
to the PC or camera.
cable correctly.
• The USB cable is not correctly
connected to the printer or camera.
• The printer is not turned on.
Page
120
109,
120
–
111,
113
–
111,
113
130
• Set up the camera, and connect the USB
cable correctly.
• Turn the printer on.
121
Solutions
Page
Z Others
Matters
Problems
Camera operation
etc.
The camera no
longer works
correctly.
Briefly remove the batteries or disconnect
the AC power adapter and DC coupler.
15, 16
Then reload the batteries or reconnect the
AC power adapter and try again.
The batteries have run out.
Load new or fully charged batteries.
Camera malfunction may be caused
temporarily.
Briefly remove the batteries or disconnect
the AC power adapter and DC coupler.
Then reload the batteries or reconnect the
15, 16
AC power adapter and DC coupler and try
again. If you think the camera is faulty,
contact your FUJIFILM dealer.
15, 17
Troubleshooting
Nothing happens
when pressing the
buttons on the
camera.
Possible causes
Camera malfunction may be caused
temporarily.
149
Specifications
System
Model
Digital camera FinePix S1000fd
Effective pixels
10.0 million pixels
CCD
1/2.3-inch CCD
Storage media
Internal memory (approx. 24 MB)/xD-Picture Card (16/32/64/128/256/512 MB/1 GB/2 GB)/SD/SDHC
Memory Card (FUJIFILM recommendation (➝p.18))
File format
Still image: DCF-compliant
Compressed: Exif ver.2.2 JPEG, DPOF-compatible
*Design rule for Camera File System compliant/DPOF compatible
Movie: AVI format, Motion JPEG
Audio: WAVE format, Monaural sound
Number of recorded pixels Still image: 3648 × 2736 pixels/3648 × 2432 pixels/2592 × 1944 pixels/2048 × 1536 pixels
1600 × 1200 pixels/640 × 480 pixels (
/%/[/3/2/`)
150
File size
See the table on the p.154
Lens
Fujinon 12× optical zoom lens
F2.8 (Wide-angle)-F5.0 (Telephoto)
Focal length
f=5.9 mm-70.8 mm
(Equivalent to approx. 33 mm-396 mm on a 35 mm camera)
Digital zoom
Approx. 5.7× (12× optical zoom lens is used together: Max. zoom scale: approx. 68.4×)
Aperture
F2.8-F6.4 (Wide-angle) to F5.0-F8.0 (Telephoto) in 1/3 EV increments Manual/Auto selectable
Focal range
(from lens surface)
Normal:
Sensitivity
[AUTO]/[AUTO(400)]/[AUTO(800)]/Equivalent to ISO [64]/[100]/[200]/[400]/[800]/[1600]/[3200]
(max.number of recorded pixels:3) (Standard output sensitivity)
Wide-angle: approx. 40 cm (1.3 ft.) to infinity (In High-speed shooting mode: approx. 1.5 m
(4.9 ft.) to infinity)
Telephoto: approx. 1.5 m (4.9 ft.) to infinity (In High-speed shooting mode: approx. 2.0 m
(6.6 ft.) to infinity)
Macro:
Wide-angle: 5 cm to 3.0 m (2.0 in. to 9.8 ft.)
Telephoto: 80 cm to 9.9 m (2.6 ft. to 32.5 ft.)
Super macro: Approx. 2 cm to 10 cm (0.8 in. to 3.9 in.)
Focal length: fixed to approx. 60 mm (35 mm camera equivalent)
System
Photometry
TTL 256-zones metering Multi, Spot, Average
Exposure control
Program AE (When using P mode : Program Shift is enabled)/Shutter priority AE/Aperture priority AE/
Manual exposure
Scene position
Intelligent Face Detection
([NATURAL LIGHT]), H ([PORTRAIT]), , ([LANDSCAPE]), . ([SPORT]), / ([NIGHT]),
([FIREWORKS]),
([SUNSET]),
([SNOW]),
([BEACH]),
([MUSEUM]),
([PARTY]),
([FLOWER]),
([TEXT]),
([PICTURE STABILIZATION])
Available
Exposure compensation
–2 EV to +2 EV in 1/3 EV-step increments (N, <, M)
Shutter speed
B,
, H, ,, .,
,
,
,
,
,
,
: 1/4 sec. to 1/2000 sec*.
/: 8 sec. to 1/1000 sec.*
: 8 sec. to 1/2 sec.*
: 1/45 sec. to 1/2000 sec.* (flash only).
N, <: 1/45 sec. to 1/2000 sec.* (8 sec. to 1/2000 sec.* when suppressed flash is set)
M, >: 8 sec. to 1/2000 sec.* *depend on Exposure mode
Continuous shooting
Continuous shooting (TOP 152):
Number of recorded frames: up to 15 frames (Max. 7.5 frames/sec.)
Continuous shooting (TOP 6[):
Number of recorded frames: up to 6 frames (Max. 3.3 frames/sec.)
Long period continuous shooting (LONG PERIOD):
Number of recorded frames: Depend on memory size. 0.7 sec. interval at
N depending on
quality level. (Max. 1.4 frames/sec.)
Continuous shooting (LAST 3):
Number of recorded frames: 3 frames just before releasing shutter button (Max. 1.4 frames/sec)
Bracketing: (BRACKETING)
Number of recorded frames: up to 3 frames (appropriate, over or under setting value)
Continuous shooting (TOP 3):
Number of recorded frames: up to 3 frames (Max. 1.4 frames/sec.)
Auto bracketing
± 1/3 EV, ± 2/3 EV, ± 1 EV
Focus
Mode: Single AF, Continuous AF
AF system: TTL contrast-type, AF-assist illuminator (effective distance: 1.8m)
AF frame selection: AF (CENTER), AF (MULTI), AF(AREA)
Continued Q
151
Specifications
System
White balance
Automatic scene recognition/Preset (Fine, Shade, Fluorescent (Daylight), Fluorescent (Warm White),
Fluorescent (Cool White), Incandescent) /Custom
Self-timer
Approx. 2 sec./10 sec.
Flash type
Auto flash
Effective range: (S: [AUTO]): approx. 40 cm-8.7 m (1.3 ft.-28.5 ft.) (Wide-angle) approx. 1.5m-4.8m
(4.9 ft.-15.7 ft.) (Telephoto)
(Macro):
approx. 30 cm-3.0 m (1.0 ft.-9.8 ft.) (Wide-angle) approx. 0.8m-3.0m
(2.6 ft.-9.8 ft.) (Telephoto)
Flash mode
Red-eye removal set to OFF: Auto, Forced Flash, Suppressed Flash, Slow Synchro
Red-eye removal set to ON: Red-eye Reduction Auto, Red-eye Reduction & Forced Flash, Suppressed Flash,
Red-eye Reduction & Slow Synchro
Viewfinder
0.20 inches, approx. 200,000 dots FLCD monitor, (Each dot displays all R, G, and B colors consecutively),
Approx. 97% coverage
LCD monitor
2.7 inches, Aspect ratio: 4:3; approx. 230,000 dots TFT color LCD monitor, Approx. 97% coverage
Movie
640 × 480 pixels/320 × 240 pixels (%/$)
(30 frames per second with monaural sound)
Photography functions
Intelligent face detection, Red eye removal, High-speed shooting, Best framing, Post shot assist window,
Frame No. memory, Histograms, Panorama
Playback functions
Intelligent face detection, Micro thumbnails playback, Trimming, Slide Show, Multi-frame playback,
Sorting by date, Image rotate, Histograms (Highlight warning), Voice memo
Other functions
PictBridge, Exif print, Language (
, English, Français, Deutsch, Español, Italiano,
,
,
,
, Português, Nederlands,
,
, Magyar, Polski, Svenska), Time difference, FinePix
photo mode(p-mode), Discharging rechargeable batteries
Input/Output Terminal
152
A/V OUT (Audio/Visual
output)
NTSC/PAL-type (with monaural sound)
Digital input/output
USB 2.0 High-Speed, PTP (Picture Transfer Protocol)/MTP (Media Transfer Protocol)
Power Supply and Others
Power supply
Guide to the number of
available frames for battery
operation
Use one of the following:
• 4× AA-size alkaline batteries
• 4x AA-size Lithium batteries (sold separately)
• 4× AA-size Ni-MH (Nickel-Metal Hydride) batteries (sold separately)
• AC Power Adapter AC-5VX (sold separately) DC Coupler CP-04 (sold separately)
Battery Type
With LCD monitor ON
With viewfinder (EVF) ON
Alkaline batteries
Approx. 300 frames
Approx. 300 frames
Ni-MH batteries 2500 mAh
Approx. 500 frames
Approx. 500 frames
Lithium batteries
Approx. 700 frames
Approx. 700 frames
According to the CIPA (Camera & Imaging Products Association) standard procedure for measuring
digital still camera battery consumption (extract):
When using alkaline batteries, use the batteries supplied with the camera. You can use Ni-MH batteries
also. The storage media should be xD-Picture Card.
Pictures should be taken at a temperature of +23°C (+73°F), with the LCD monitor turned on, the optical
zoom moved from full wide-angle to full telephoto (or vice-versa) and back again to its original position
every 30 seconds, the flash used at full power every second shot and the camera turned off and then on
again once every 10 shots.
• Note: Because the number of available shots varies depending on the capacity of alkaline batteries,
lithium batteries or the level of charge in Ni-MH batteries, the figures shown here for the number
of available shots using batteries are not guaranteed.
The number of available shots will also decline at low temperatures.
Camera dimensions (W/H/D) 102.5 mm × 73 mm × 67.8 mm/4.0 in. × 2.9 in. × 2.7 in. (not including accessories and attachments)
Camera mass (weight)
Approx. 325 g/11.5 oz. (not including accessories, batteries and Memory Card)
Weight for photography
Approx. 420 g/14.8 oz. (including batteries and Memory Card)
Operating Conditions
Temperature: 0°C to +40°C (+32°F to +104°F)
85% humidity or less (no condensation)
Continued Q
153
Specifications
Z Standard number of available frames/recording time per xD-Picture Card, SD Memory Card and internal memory
The number of available frames and recording time is approximate. Actual number of frames and recording time varies
depending on the types of Memory Card or shooting condition. Also, the number of frames and recording time displayed in the
LCD monitor may not decrease regularly.
Quality setting
Number of recorded
pixels
Image data size
Internal memory
(approx. 24 MB)
F
N
3648 × 2736
%
[
3
2
`
%
(30 fps)
$
(30 fps)
3648 × 2432 2592 × 1944 2048 × 1536 1600 × 1200 640 × 480 640 × 480 320 × 240
4.9 MB
2.5 MB
2.2 MB
1.3 MB
789 KB
5
9
11
19
30
631 KB
38
134 KB
170
–
–
29 sec.
53 sec.
3
6
7
12
19
24
110
19 sec.
34 sec.
32 MB
6
12
14
25
39
49
221
38 sec.
1.1 min.
64 MB
13
25
29
50
79
99
444
1.2 min.
2.3 min.
128 MB
26
51
58
101
159
199
888
2.5 min.
4.6 min.
256 MB
52
103
116
202
319
399
1777
5.1 min.
9.2 min.
512 MB
104
207
233
404
639
799
3551
10.2 min.
18.4 min.
1 GB
209
415
466
809
1279
1599
7108
20.5 min.
37.0 min.
2 GB
418
830
927
1599
2559
3199
12796
41.1 min.
74.0 min.
SD
Memory
Card
512 MB
101
200
225
391
618
773
3438
9.9 min.
17.9 min.
1 GB
202
402
452
784
1239
1549
6885
19.9 min.
35.8 min.
2 GB
405
804
898
1549
2479
3098
12395
39.8 min.
71.7 min.
SDHC
Memory
Card
4 GB
811
1611
1798
3102
4964
6205
24518
79.8 min.*
143.6
min.*
8 GB
1627
3233
3608
6225
9960
12450
47132
160.1
min.*
288.1
min.*
xD-Picture Card
16 MB
* A movie recording will stop automatically when a movie file becomes approx. 2GB. If you want to continue recording another
movie, press the shutter button again. The available recording time is displayed based on approx. 2GB.
154
If you shoot using the xD-Picture Cards with model numbers containing “M” such as DPC-M1GB, movie recording time may be
reduced if you repeatedly record and erase (frame erase) image files. In such a case, erase all frames or format the xD-Picture Card
before use. Back up important frames (files) onto your PC or another media.
* These specifications are subject to change without notice. FUJIFILM shall not be held liable for damages resulting from
errors in this Owner’s Manual.
* The LCD monitor on your digital camera is manufactured using advanced high-precision technology. Even so, small bright
points and anomalous colors (particularly around text) may appear on the monitor. These are normal display characteristics
and do not indicate a fault with the monitor. This phenomenon will not appear on the recorded image.
* The operation error may be caused in a digital camera by the strong radio interference (i. e. electric fields, static electricity,
line noise, etc.).
* Due to the nature of the lens, the edges of images may appear distorted. This is normal.
155
Explanation of Terms
Deactivated batteries
Leaving an Ni-MH battery unused in storage for a long period may cause a rise in the level of substances that inhibit current
flow inside the battery and result in a dormant battery. A battery in this state is referred to as deactivated.
Because current flow is inhibited in a deactivated Ni-MH battery, the battery’s original level of performance cannot be achieved.
EV
A number denotes Exposure Value. The EV is determined by the brightness of the subject and sensitivity (speed) of the film
or CCD. The number is larger for bright subjects and smaller for dark subjects. As the brightness of the subject changes, a
digital camera maintains the amount of light hitting the CCD at a constant level by adjusting the aperture and shutter speed.
When the amount of light striking the CCD doubles, the EV increases by 1. Likewise, when the light is halved, the EV decreases
by 1.
Frame rate (fps)
The frame rate refers to the number of images (frames) that are photographed or played back per second. For example, when
10 frames are continuously photographed in a 1-second interval, the frame rate is expressed as 10 fps.
For reference, TV images are displayed at 30 fps (NTSC).
JPEG
Joint Photographic Experts Group
A file format used for compressing and saving color images. The higher the compression rate, the greater the loss of quality in
the decompressed (restored) image.
Memory effect
If an Ni-MH battery is repeatedly charged without first being fully discharged, its performance may drop below its original level.
This is referred to as the “memory effect”.
Motion JPEG
A type of AVI (Audio Video Interleave) file format that handles images and sound as a single file. Images in the file are recorded
in JPEG format. Motion JPEG can be played back by QuickTime 3.0 or later.
Smear
A phenomenon specific to CCDs whereby white streaks appear on the image when there is a very strong light source, such as
the sun or reflected sunlight, in the photography screen.
WAVE
A standard format used on Windows systems for saving audio data. WAVE files have the “.WAV” file extension and the data
can be saved in either compressed or uncompressed format. Uncompressed recording is used on this camera.
WAVE files can be played back on a personal computer using the following software:
Windows: MediaPlayer
Macintosh: QuickTime Player
* QuickTime 3.0 or later
156
White Balance
Whatever the kind of the light, the human eye adapts to it so that a white object still looks white. On the other hand, devices
such as digital cameras see a white subject as white by first adjusting the color balance to suit the color of the ambient light
around the subject. This adjustment is called matching the white balance.
Exif Print Format is a newly revised digital camera file format that contains a variety of shooting information for optimal printing.
157
FUJIFILM Digital Camera Worldwide Network
If you have technical questions or if you need repair service, ask the following local distributor.
Please present the warranty card and your purchase receipt when you ask for repairs. Refer to the warranty card for conditions of the warranty.
There is a case that repair and Technical support cannot be accepted for some models which your local distributor does not deal with.
These lists are subject to change without notice.
NORTH AMERICA
Canada
U.S.A.
FUJIFILM Canada Inc.
Technical support
Repair service
FUJIFILM U.S.A., Inc.
Technical support
Repair service
CENTRAL & SOUTH AMERICA
Argentina
Imagen e informacion S.A.
Technical support & Repair service
158
600 Suffolk Court Mississauga Ontario, L5R 4G4
TEL 1-866-818-FUJI (3854) http://www.fujihelp.ca
600 Suffolk Court Mississauga Ontario, L5R 4G4
TEL 1-800-263-5018 FAX 1-905-755-2993 http://www.fujihelp.ca
1100 King George Post Rd., Edison, NJ 08837
TEL 800-800-3854 FAX 732-857-3487 digitalinfo@fujifilm.com
1100 King George Post Rd., Edison, NJ 08837
TEL 732-857-3000 FAX 732-857-3471 njcamerarepair@fujifilm.com
Bolivia
Reifschneider Bolivia Ltda.
Technical support & Repair service
Fondo de la Legua 936 San Isidro Pcia. de Buenos Aires
TEL +54-11-4836-1000 FAX +54-11-4836-1144
servtec@imageneinformacion.com.ar
Calle H N.° 5 - Equipetrol Norte - Santa Cruz
TEL +591 33 44 1129 FAX +591 33 45 2919 gciagral@bibosi.scz.entelnet.bo
Brazil
FUJIFILM do Brasil Ltda.
Technical support & Repair service
Av. Vereador José Diniz, 3400 - Campo Belo, Sào Paulo/SP
TEL 0800-12-8600 FAX +55 11 5091-4150 camarasdigitais@fujifilm.com.br
Chile
Reifschneider SA
Technical support & Repair service
Av. El Conquistador del Monte 5024, Huechuraba, Santiago, Chile
TEL 02-4431500 FAX 02-4431596 ceciliacalvo@reifschneider.cl
Colombia
Animex de Colombia Ltda.
Technical support & Repair service
Calle 44 N.° 13-43 Piso 2 Apartado 18001 - Bogotá
TEL +57 1 338-0299 FAX +57 1 288-2208 animex@etb.net.co
Ecuador
Espacri Cia Ltda
Technical support & Repair service
Bolivar 5-69 y Hermano Miguel
TEL 593-72-835526 FAX 593-72-833157
Ecuador
Importaciones Espacri Cia. Ltda.
Technical support & Repair service
Simón Bolivar 5-69 y Hno. Miguel - Cuenca
TEL +593 783 5526 FAX +593 783 3157 portiz@fujifilm.com.ec
Mexico
Fujifilm de Mexico, S.A. de C.V.
Technical support
Av. Ejercito Nacional 351, Col. Granada 11520 Mexico, D.F.
TEL (52-55) 5263-5566 / 68 FAX (52-55) 5254-1508 jlgiraud1@fujifilm.com.mx
Repair service
Av. Presidente Juarez 2007, Col. Tepetlacalco, 54090 Tlalnepantla, Edo. de
Mexico
TEL (52-55) 5263-5500 FAX (52-55) 5254-1508 jlgiraud1@fujifilm.com.mx
Paraguay
Errece S.R.L.
Technical support & Repair service
Edificio Unitas 15 de Agosto 1035, Asunción
TEL +595 21 444256 FAX +595 21 444651 jmarbulo@fujifilm.com.py
Peru
Procesos de Color S.A.
Technical support & Repair service
Pablo Bermudez 111 Apartado 3794 - Esq. Arequipa - Lima 11
TEL +51 14 33 5563 FAX +51 14 33 7177 jalvarado@fujifilm.com.pe
Uruguay
Fotocamara S.R.L.
Technical support & Repair service
Cuareim 1439, montevideo, Uruguay
TEL +598-2-9002004 FAX +598-2-9008430 fotocam@adinet.com.uy
Uruguay
Kiel S.A.
Technical support & Repair service
Maldonado 1787 Montevideo- Uruguay
TEL (05982) 419 4542 FAX (05982) 412 0046 kiel@fujifilm.com.uy
Venezuela
C. Hellmund & Cia Sa
Technical support & Repair service
Av. Ppal Diego Cisneros Caracas Venezuela Edf Oficentro
TEL 0212-2022300 FAX 0212-2399796 hellmund@hellmund.com
Fuji Film Oesterreich
Technical support & Repair service
Traviatagasse/Pfarrgasse, 1230 Vienna, Austria
TEL 0043 1 6162606/51 or 52 FAX 0043 1 6162606/58
kamera.service@fujifilm.at
20, Avenue Lavoisier, Wavre, 1300, Belgium
TEL 3210242090 FAX 3210238562 info@fuji.be
EUROPE
Austria
Belgium
Belgian Fuji Agency
Technical support & Repair service
Croatia
I&I d.o.o.
Technical support
Repair service
Hondlova 2, Zagreb, Croatia
TEL 38512319060 FAX 2310240 dsaravanja@fujifilm.hr
Hondlova 2, Zagreb, Croatia
TEL 38512316228 FAX 2310240 info@fujifilm.hr
11, Dighenis Akritas Avenue, P.O.BOX 22315, 1586 Nicosia
TEL 35722746746 FAX 35722438209 mariosashiotis@fujifilm.com.cy
Cyprus
PMS IMAGING LTD
Technical support & Repair service
Cyprus
Doros Neophytou
CAMERA REPAIRS
Technical support & Repair service
28B, Agiou Demetriou, Acropoli, Nicosia
TEL 35722314719 FAX 35722515562 dorosn@logosnet.cy.net
Czech Republic
Fujifilm Cz., s.r.o.
Technical support
U nakladoveho nadrazi 2/1949, 130 00 Praha 3
TEL 00420 234 703 411 FAX 00420 234 703 489 fricman@fujifilm.cz
Czech Republic
AWH servis
Repair service
Milesovska 1, 130 00 Praha 3, Czech republic
TEL 00420 222 721 525 FAX 00420 222 720 122 awh@awh.cz
Denmark
Fujifilm Danmark A/S
Technical support & Repair service
Stubbeled 2, 2950 Vedbæk Denmark
TEL 0045 45662244 FAX 0045 45662214 fujifilm@fujifilm.dk
Finland
Fuji Finland Oy
Technical support & Repair service
Martinkyläntie 41, 01720 Vantaa, Finland
TEL +358 9 825951 FAX +358 9 870 3818 fuji@fuji.fi
France
FUJIFILM France
Technical support & Repair service
9 rue d’Alembert BAT A1 ZA Pissaloup 78190 Trappes, France
FAX 33 1 01 30 58 58 65direction.technique@pm2s.fr
159
FUJIFILM Digital Camera Worldwide Network
Germany
Greece
Hungary
FUJIFILM Electronic Imaging Europe Benzstrasse 2, 47533 Kleve, Germany
International call TEL +49 211 50890 FAX +49 211 5089668 service@fujifilm.de
GmbH
National call* TEL 0180 5898980 FAX 0180 5898982
Technical support & Repair service
*12 Cent/Min aus dem deutschen Festnetz
1, Ihous & Ag. Anargiron str., 175 64 P.Phaliro, Athens, Greece
FUJIFILM HELLAS S.A.
TEL 0030 210 9404100 FAX 0030 210 9404397 fujifilm@fujifilm.gr
Technical support & Repair service
Foto-Paradicsom Kft.
Technical support & Repair service
Technical support
Iceland
Icephoto (Ljosmyndavorur)
Technical support & Repair service
Italy
FujiFilm Italia S.p.A.
Technical support
Repair service
Vaci ut 19. Budapest, 1134, Hungary
TEL 3612389410 FAX 3612389401 fujifilm@fujifilm.hu
Skipholt 31, 105 Reykjavik, Iceland
TEL 354 568 0450 FAX 354 568 0455 framkollun@fujifilm.is
Via Dell’Unione Europea, 4 - 20097 San Donato Milanese (MI), Italy
TEL 039-02895821 FAX 039-0289582912 info@fujifilm.it
Lithuania
Fujifilm Lithuania
Technical support & Repair service
Fujifilm On Line - Call center
TEL 039-026695272 info@fujifilm.it
Gerosios Vilties str. 38, LT-03143 Vilnius, Lithuania
TEL 370-5-2130121 FAX 3705-5-2134066 info@fujifilm.lt
Malta
Ciancio (1913) Co.Ltd.
Technical support & Repair service
Fuji Tech Centre, Ciancio House, Cannon Road, Qormi, QRM05
TEL 0356-21-480500 FAX 0356-21-488328 info@fujifilm.com.mt
Norway
Lilleakerveien 10, 0283 Oslo, Norway
TEL 0047-02273 FAX 0047-22736020 http://www.fujifilm.no/
mailto:post@fujifilm.no
Repair service
Liaveien 1, 5132 Nyborg, Norway
TEL 0047-55393880 FAX 0047-55195201 http://www.camera.no/
mailto:service@camera.no
Fujifilm Polska Distribution Sp. z o.o. Poland Al..Jerozolimskie 178; 02-486 Warszawa
TEL +48-22-517-66-00 FAX +48-22-517-66-02 fujifilm@fujifilm.pl
Technical support
Poland
Fujifilm Norge AS
Technical support
Repair service
Portugal
Romania
160
Nagy Lajos király útja 20. Budapest, 1148, Hungary
TEL 361363377 FAX 3612234250
Fujifilm Portugal, Lda
Technical support
Repair service
CTS-Cardinal Top Systems Ltd
Technical support & Repair service
Poland, Muszkieterow 15, 02-273 Warszawa
TEL +48-22-886-94-40 FAX +48-22-886-94-42 serwis@fujifilm.pl
Av. Fontes Pereira de Melo, 342, 4100-259 Porto, Portugal
TEL (351) 226194200 FAX (351) 226194213 finepix@fujifilm.pt
Av. Fontes Pereira de Melo, 342, 4100-259 Porto, Portugal
TEL (351) 226194200 FAX (351) 225194662 cameras@fujifilm.pt
112, Calea Dorobanti street, 4 flat, 1sector, Bucharest, Romania
TEL 4021-230-09-82 FAX 4021-230-09-82 cts_tirla@hotmail.com
Russia
Slovakia
Spain
Sweden
ZAO “Fujifilm RU”
Technical support
Repair service
Fujifilm Slovakia
Technical support
Repair service
Fujifilm España S.A.
Technical support
Repair service
Fujifilm Sverige AB
Technical support
Repair service
Bld. 1, 10, Rozanova str., Moscow, 123007, Russia
TEL +7-495-956-98-58 FAX +7-495-230-62-17 info@fujifilm.ru
www.fujifilm.ru
TEL +7-495-956-98-58
Pribylinska 2, 831 04 Bratislava, Slovakia
TEL 00421 2 44 888 077 FAX 00421 2 44 889 300 fujifilm@fujifilm.sk
FIS Tatracentrum, Hodzovo nam. 4 - Tatracentrum, 811 06 Bratislava, Slovakia
TEL 00421 2 54 647 347 fis.tatracentrum@stonline.sk
Aragón 180, 08011 Barcelona (España)
TEL 902012535 FAX 934515900 / 933230330 info@fujifilm.es
Aragón 180, 08011 Barcelona (España)
TEL 934511515 FAX 934515900 / 933230330 tallersat@fujifilm.es
Sveavägen 167 104 35 Stockholm
TEL 46 8 506 141 70 FAX 46 8 506 142 09 kamera@fujifilm.se
Sveavägen 167 104 35 Stockholm
TEL 46 8 506 513 54 FAX 46 8 506 513 99 kameraverkstaden@fujifilm.se
Niederhaslistrasse 12, 8157 Dietlikon, Switzerland
TEL +41 44 855 5154 FAX +41 44 855 5329 RepairCenter@fujifilm.ch
Switzerland /
Lichtenstein
Fujifilm (Switzerland) AG
Technical support & Repair service
The Netherlands
FUJIFILM Electronic Imaging
Nederland
Technical support
Hoogstraat 35, 3011 PE Rotterdam, Nederlands
TEL +31(0)102812500 FAX +31(0)102812560 helpdesk@fujifilm-digital.nl
Repair service
Hoogstraat 35, 3011 PE Rotterdam, Nederlands
TEL +31(0)102812520 FAX +31(0)102812550 camerareparaties@fujifilm-digital.nl
Fujifilm Plaza, Dereboyu Cad. 39 34660 Halkali, Istanbul, Turkey
TEL +90 212 696 5090 FAX +90 212 696 5009 csarp@fujifilm.com.tr
Turkey
U.K.
Ukraine
MIDDLE EAST
Iran
Fujifilm Turkiye Sinfo A.S.
Technical support
Repair service
FUJIFILM UK Ltd.
Technical support
Repair service
Fujifilm Plaza, Dereboyu Cad. 39 34660 Halkali, Istanbul, Turkey
TEL +90 212 696 5090 FAX +90 212 696 5010 servis@fujifilm.com.tr
St Martins Way St Martins Business Centre Bedford MK42 0LF
TEL +44 (0)123 424 5383 FAX +44 (0)123 424 5285 fujitec@fuji.co.uk
Image Ukraine CJSC
Technical support & Repair service
St Martins Way St Martins Business Centre Bedford MK42 0LF
TEL +44 (0)123 421 8388 FAX +44 (0)123 424 5285 fujitec@fuji.co.uk
12, Kontraktova ploshcha, Kyiv 04070, Ukraine
TEL +380-44-4909075 FAX +380-44-4909076 d@fujifilm.ua
Tehran Fuka Co.
Technical support & Repair service
229,“Fuji” Bldg., Mirdamad Blvd., Tehran 19189, Iran
TEL (+98-21)2254810-19 FAX (+98-21)2221002 fuka@neda.net
161
FUJIFILM Digital Camera Worldwide Network
Israel
Efal 33 keyriat Arie Petah Tikva 49130, Israel
TEL (+ ) 972 3 9250666 digital@fujifilm.co.il
Jordan
Grand Stores
Technical support & Repair service
Efal 33 keyriat Arie Petah Tikva 49130, Israel
TEL (+ ) 972 3 9250666 FAX 972 3 9250699 khaim@shimone.com
Al- Abdali, Amman / Jordan
TEL 009626-4646387 FAX 009626-4647542 gstores@go.com.jo
Qatar
Techno Blue
Technical support
Blue Salon Bldg, 3rd Floor, Suhaim bin Hamad st, Al- Saad, Doha
TEL 00974 44 66 175 FAX 00974 44 79 053 prabu@techno-blue.com
Saudi Arabia
Emam Distribution Co. Ltd.
Technical support
P.O. Box 1716, Jeddah 21441, Saudi Arabia
TEL 96626978756 FAX 96626917036 service@fujifilm.com.sa
Syria
Film Trading Company
Technical support
Repair service
Al-Shahbandar P.O. Box:31180 Damascus SYRIA
TEL + 963 11 2218049 FAX + 963 11 44673456 f.t.c@Net.SY
Al-cheikh Taha P.O. Box: 6171 Aleppo SYRIA
TEL + 963 21 4641903 FAX + 963 21 4641907 filmtradin@Net.SY
P. O. Box 2144, Saleh Bin Lahej Building, Al Garhoud, Deira, Dubai
TEL + 971-4-2823700 FAX + 971-4-2828382 photography@grandstores.ae
U.A.E.
Grand Stores
Technical support & Repair service
Yemen
Al-Haidary Trading
Technical support
Repair service
P.O.Box-2942 Haddah St. HTC, Sana’a, Yemen
TEL 00967-1-503980 FAX 00967-1-503983
Foto Express Egypt
Technical support & Repair service
426 Pyramids St., Giza, Egypt
TEL (202) 7762062 FAX (202) 7760169 fotoegypt@access.com.eg
Fuji Kenya Ltd
Repair service
P.O.Box 41669-00100, Fuji Plaza, Chiromo Road, Nairobi, Kenya.
TEL (254-20)4446265-8 FAX (254-20)4448515 / 7 info@fujifilm.co.ke
FUJIFILM Australia Pty Ltd
Technical support & Repair service
Locked Bag 5100, Brookvale, NSW, 2100
TEL 1800 226 355 FAX +61 (2) 9466 2854 digital@fujifilm.com.au
Fiji
Brijlal & Co. Ltd
Technical support & Repair service
70-72 Cumming Street,Suva,Fiji
TEL (679)3304133 FAX (679)3302777 kapadia@connect.com.fj
New Caledonia
Phocidis SARL
Technical support & Repair service
58, rue Higginson - B.P.661 - 98845
TEL (00 687) 25-46-35 FAX (00 687) 28-66-70 phocidis@phocidis.nc
New Zealand
Fujifilm NZ Ltd
Technical support & Repair service
Cnr William Pickering & Bush Road Albany, Auckland
TEL +64-9-4140400 FAX +64-9-4140410 glenn.beaumont@fujifilm.co.nz
Papua New Guinea
Oceania PNG Limited
Technical support
Section 15, Allotment 1, Reke St, Boroko NCD. PNG. Mail: PO Box 2167, Boroko
NCD. PNG. TEL +675 3256411 FAX +675 3250311 oceania@daltron.com.pg
AFRICA
Egypt
Kenya
OCEANIA
Australia
162
Shimone Group Ltd.
Technical support
Repair service
P.O.Box-2942 Haddah St. HTC, Sana’a, Yemen
TEL 00967-1-503977 FAX 00967-1-503983
ASIA
Hong Kong
Fuji Photo Products Co., Ltd.
Technical support & Repair service
8/F.,TSUEN WAN IND. CENTRE, 220 TEXACO RD., TSUEN WAN, HONG KONG
TEL (852)2406 3287 FAX (852)2408 3130 rsd@chinahkphoto.com.hk
Indonesia
PT Modern Photo Tbk
Technical support & Repair service
Malaysia
FUJIFILM (Malaysia)
Sdn. Bhd.
Technical support
Repair service
Jl.Matraman Raya 12, Jakarta Timur 13150
TEL +62 021 2801000 FAX +62 021 8581620+62 021 2801012
assd_kmr@modernphoto.co.id
Letter Box 1, Level 10, 11 & 12, Menara Axis, No 2, Jalan 51A/223, 46100 Petaling
Jaya, Selangor Darul Ehsan, Malaysia
TEL 603-79584700 FAX 603-79584110 digital@fujifilm.com.my
Philippines
YKL Development & Trdg. Corp.
Technical support
Repair service
Letter Box 1, Level 10, 11 & 12, Menara Axis, No 2, Jalan 51A/223, 46100 Petaling
Jaya, Selangor Darul Ehsan, Malaysia
TEL 603-79584700 FAX 603-79584110 technical@fujifilm.com.my
24 Sto. Domingo St., Quezon City 1100, Philippines
TEL 632-7436601~06 FAX 632-7324661 digital@yklcolor.com
Singapore
FUJIFILM (Singapore) Pte Ltd
Technical support & Repair service
24 Sto. Domingo St., Quezon City 1100, Philippines
TEL 632-7436601~06 FAX 632-7324661 tech_services@yklcolor.com
10 New Industrial Road Fujifilm Building Singapore 536201
TEL 65-6380 5557 FAX 65-6281 3594 service@fujifilm.com.sg
South Korea
Korea Fujifilm Co., Ltd.
Technical support
30-1, Mukjeung-dong, Jung-gu, Seoul, Korea
TEL +82-2-3282-7363 FAX +82-2-2269-7435 photo@fujifilm.co.kr
South Korea
Yonsan AS Center (Fujidigital)
Repair service
#301, 3F, Jeonjaland, 16-9, Hangangro3-ga, Yongsan-gu, Seoul, Korea
TEL +82-2-701-1472 FAX +82-2-718-1331 1bowl@hanmail.net
South Korea
Kangnam AS Center (Digitalgallery)
Repair service
2F, Hyeongin Tower, 23-2, Bangyi-dong, Songpa-gu, Seoul, Korea
TEL +82-2-2203-1472 FAX +82-2-418-5572 nurijili@hanmail.net
South Korea
Busan AS Center (Digital-Sewon)
Repair service
241-4, Bujeon-dong, Busanjin-gu, Busan, Korea
TEL +82-51-806-1472 FAX +82-51-817-0083 merahan@yahoo.co.kr
Taiwan
Hung Chong Corp.
Technical support & Repair service
No. 38, Min-Chuan E. Rd. Sec. 6, Taipei (114), Taiwan, R.O.C.
TEL 886-2-6602-8988 FAX 886-2-2791-8647 dah@mail.hungchong.com.tw
Thailand
FUJIFILM (Thailand) Ltd.
Technical support
Repair service
388 SP Building, 8th Floor, Phayathai, Bangkok 10400
TEL +662-2730029 ext. 755 FAX +662-2730239 supaleark@fujifilm.co.th
Vietnam
International Minh Viet Co., Ltd.
Technical support & Repair service
388 SP Building, 8th Floor, Phayathai, Bangkok 10400
TEL +662-2730029 ext.761,762 FAX +662-2730239 warin@fujifilm.co.th
99-107 Bach Van street, Ward 5, District 5, Ho chi minh city
TEL +84-8-8366807 ext.122 FAX +84-8-8380621 diep.phanthithanh@imv.com.vn
163
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN
http://www.fujifilm.com/products/digital_cameras/index.html
Printed in China
Notes and Cautions
IMPORTANT SAFETY INSTRUCTIONS
Read Instructions:
All the safety and operating instructions should
be read before the appliance is operated.
Retain Instructions:
The safety and operating instructions should be
retained for future reference.
Heed Warnings:
All warnings on the appliance and in the
operating instructions should be adhered to.
Follow Instructions:
All operating and use instructions should be
followed.
Installation
Power Sources—This video product should be
operated only from the type of power source
indicated on the marking label. If you are not
sure of the type of power supply to your home,
consult your appliance dealer or local power
company. For video products intended to
operate from battery power, or other sources,
refer to the operating instructions.
Grounding or Polarization—This video
product is equipped with a polarized
alternating-current line plug (a plug having one
blade wider than the other). This plug will fit into
the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully
into the outlet, try reversing the plug. If the plug
should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
Alternate Warnings—This video product is
equipped with a 3-wire grounding-type plug, a
plug having a third (grounding) pin. This plug
will only fit into a grounding-type power outlet.
This is a safety feature. If you are unable to
insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the groundingtype plug.
Overloading—Do not overload wall outlets and
extension cords as this can result in a risk of fire
or electric shock.
Ventilation—Slots and openings in the cabinet
are provided for ventilation and to ensure
reliable operation of the video product and to
protect it from overheating, and these openings
must not be blocked or covered.
The openings should never be blocked by
placing the video product on a bed, sofa, rug,
or other similar surface.
This video product should not be placed in a
built-in installation such as a bookcase or rack
unless proper ventilation is provided or the
manufacturer’s instructions have been adhered
to.
This video product should never be placed near
or over a radiator or heat register.
Attachments—Do not use attachments not
recommended by the video product
manufacturer as they may cause hazards.
Water and Moisture—Do not use this video
product near water – for example, near a bath
tub, wash bowl, kitchen sink, or laundry tub, in a
wet basement, or near a swimming pool, and
the like.
Power-Cord Protection—Power-Supply cords
should be routed so that they are not likely to be
walked on or pinched by items placed upon or
against them, paying particular attention to
cords at plugs, convenience receptacles, and
the point where they exit from the appliance.
Accessories—Do not place this video product
on an unstable cart, stand, tripod, bracket, or
table. The video product may fall, causing
serious injury to a child or adult, and serious
damage to the appliance. Use only with a cart,
stand, tripod, bracket, or table recommended
by the manufacturer, or sold with the video
product. Any mounting of the appliance should
follow the manufacturer’s instructions, and
should use a mounting accessory
recommended by the manufacturer.
An appliance and cart combination should be
moved with care. Quick stops, excessive force,
and uneven surfaces may cause the appliance
and cart combination to overturn.
Antennas
Outdoor Antenna Grounding—If an outside
antenna or cable system is connected to the
video product, be sure the antenna or cable
system is grounded so as to provide some
protection against voltage surges and built-up
static charges. Section 810 of the National
Electrical Code, ANSI/NFPA No. 70, provides
information with respect to proper grounding of
the mast and supporting structure, grounding of
the lead-in wire to an antennadischarge unit,
size of grounding conductors, location of
antenna-discharge unit, connection to
grounding electrodes, and requirements for the
grounding electrode.
Power Lines—An outside antenna system
should not be located in the vicinity of overhead
power lines or other electric light or power
circuits, or where it can fall into such power lines
or circuits. When installing an outside antenna
system, extreme care should be taken to keep
from touching such power lines or circuits as
contact with them might be fatal.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
Ground
Clamp
Electric
Service
Equipment
Antenna
Lead in
Wire
Antenna
Discharge Unit
(NEC SECTION 810-20)
Grounding Conductors
(NEC SECTION 810-21)
Ground Clamps
Power Service Grounding
Electrode System
(NEC ART 250. PART H)
Use
Cleaning—Unplug this video product from the
wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth
for cleaning.
Object and Liquid Entry—Never push objects
of any kind into this video product through
openings as they may touch dangerous voltage
points or shortout parts that could result in a fire
or electric shock. Never spill liquid of any kind
on the video product.
Lightning—For added protection for this video
product receiver during a lightning storm, or
when it is left unattended and unused for long
periods of time, unplug it from the wall outlet
and disconnect the antenna or cable system.
This will prevent damage to the video product
due to lightning and power-line surges.
Service
Servicing—Do not attempt to service this video
product yourself as opening or removing covers
may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service
personnel.
Damage Requiring Service—Unplug this
video product from the wall outlet and refer
servicing to qualified service personnel under
the following conditions:
When the power-supply cord or plug is
damaged.
If liquid has been spilled, or objects have fallen
into the video product.
If the video product has been exposed to rain or
water.
If the video product has been dropped or the
cabinet has been damaged.
If the video product does not operate normally
be following the operating instructions. Adjust
only those controls that are covered by the
operating instructions as an improper
adjustment of other controls may result in
damage and will often require extensive work by
a qualified technician to restore the video
product to its normal operation.
■ Trademark Information
•
and xD-Picture Card™ are trademarks of
FUJIFILM Corporation.
• IBM PC/AT is a registered trademark of
International Business Machines Corp. of the
U.S.A.
• Macintosh, Power Macintosh, iMac, PowerBook,
iBook and Mac OS are trademarks of Apple Inc.,
registered in the U.S. and other countries.
• Microsoft, Windows, the Windows logo,
Windows Vista and the Windows Vista logo are
trademarks or registered trademarks of
Microsoft Corporation in the United States and/
or other countries. Windows is an abbreviated
term referring to the Microsoft® Windows®
Operating System.
* The “Designed for Microsoft® Windows® XP”
logo refers to the camera and the driver only.
Before Using the Camera
• IrSimple™ Trademark is owned by the Infrared
Data Association®.
Read the back side before using the camera.
• IrSS™ Trademark or IrSimpleShot™ Trademark
■ Test Shots Prior to Photography
is owned by the Infrared Data Association®.
For important photographs (such as weddings
• SDHC logo is a trademark.
and overseas trips), always take a test shot and
• Other company or product names are
view the image to make sure that the camera is
trademarks or registered trademarks of the
working normally.
respective companies.
• FUJIFILM Corporation cannot accept liability for
■ Notes on Electrical Interference
any incidental losses (such as the costs of
If the camera is to be used in hospitals or aircrafts,
photography or the loss of income from
please note that this camera may cause
photography) incurred as a result of faults with
interference to other equipment in the hospital or
this product.
aircraft. For details, please check with the
■ Notes on Copyright
applicable regulations.
Images recorded using your digital camera system
■ Explanation of Color Television System
cannot be used in ways that infringe copyright
NTSC: National Television System Committee,
laws without the consent of the owner, unless
color television telecasting specifications
intended only for personal use. Note that some
adopted mainly in the U.S.A., Canada and
restrictions apply to the photographing of stage
Japan.
performances, entertainments and exhibits, even
PAL: Phase Alternation by Line, a color
when intended purely for personal use. Users are
television system adopted mainly by
also asked to note that the transfer of Memory
European countries and China.
Card containing images or data protected under
copyright laws is only permissible within the
■ Exif Print (Exif ver. 2.2)
restrictions imposed by those copyright laws.
Exif Print Format is a newly revised digital camera
file format that contains a variety of shooting
■ Handling Your Digital Camera
information for optimal printing.
To ensure that images are recorded correctly, do
* See “Using Your Camera Correctly”
not subject the camera to impact or shock while
(→OWNER’S MANUAL) for more information.
an image is being recorded.
■ Liquid Crystal
If the LCD monitor is damaged, take particular
⇒ Also, read the back page.
care with the liquid crystal in the monitor. If any of
the following situations arise, take the urgent
action indicated.
• If liquid crystal comes in contact with your skin:
Wipe the area with a cloth and then wash
thoroughly with soap and running water.
• If liquid crystal gets into your eye:
Flush the affected eye with clean water for at
least 15 minutes and then seek medical
assistance.
• If liquid crystal is swallowed:
Flush your mouth thoroughly with water. Drink
large quantities of water and induce vomiting.
Then seek medical assistance.
When the video product exhibits a distinct
change in performance - this indicates a need
for service.
Replacement Parts—When replacement parts
are required, be sure the service technician has
used replacement parts specified by the
manufacturer or have the same characteristics
as the original part. Unauthorized substitutions
may result in fire, electric shock or other
hazards.
Safety Check—Upon completion of any
service or repairs to this video product, ask the
service technician to perform safety checks to
determine that the video product is in proper
operating condition.
7-3, AKASAKA 9-CHOME, MINATO-KU,
TOKYO 107-0052, JAPAN
BL00741-200
http://www.fujifilm.com/products/
digital_cameras/index.html
Power Supply and Battery
Be sure to read this notes before using
Safety Notes
WARNING
• Make sure that you use your camera correctly. Read these
Safety Notes and your Owner’s Manual carefully before use.
• After reading these Safety Notes, store them in a safe place.
About the Icons
• The icons shown below are used in this document to indicate
the severity of the injury or damage that can result if the
information indicated by the icon is ignored and the product is
used incorrectly as a result.
WARNING
This icon indicates that death or
serious injury can result if the
information is ignored.
CAUTION
This icon indicates that personal
injury or material damage can result
if the information is ignored.
The icons shown below are used to indicate the nature of the
information which is to be observed.
Triangular icons tell you that this information requires
attention (“important”).
Circular icons with a diagonal bar tell you that the
action indicated is prohibited (“Prohibited”).
Filled circles with an exclamation mark tell you an
action that must be performed (“Required”).
WARNING
If a problem arises, turn the camera off, remove
the battery, disconnect and unplug the AC
power adapter.
Continued use of the camera when it is emitting
smoke, is emitting any unusual odor, or is in any
other abnormal state can cause a fire or electric
shock.
• Contact your FUJIFILM dealer.
Do not allow water or foreign objects to enter
the camera.
If water or foreign objects get inside the camera,
turn the camera off, remove the battery and
disconnect and unplug the AC power adapter.
Continued use of the camera can cause a fire or
electric shock.
• Contact your FUJIFILM dealer.
Do not use the camera in the bathroom or
shower.
This can cause a fire or electric shock.
Never attempt to change or take apart the
camera. (Never open the casing.)
Do not use the camera when it has been
dropped or the casing is damaged.
This can cause a fire or electric shock.
• Contact your FUJIFILM dealer.
Do not change, heat or unduly twist or pull the
connection cord and do not place heavy objects
on the connection cord.
These actions could damage the cord and cause a
fire or electric shock.
• If the cord is damaged, contact your FUJIFILM
dealer.
Do not place the camera on an unstable surface.
This can cause the camera to fall or tip over and
cause injury.
Never attempt to take pictures while in motion.
Do not use the camera while you are walking or
driving a vehicle.
This can result in you falling down or being involved
in a traffic accident.
Do not touch any metal parts of the camera
during a thunderstorm.
This can cause an electric shock due to induced
current from the lightning discharge.
Do not use the battery except as specified.
Load the battery as aligned with the indicator.
Do not heat, change or take apart the battery.
Do not drop or subject the battery to impacts.
Do not store the battery with metallic products.
Do not use chargers other than the specified
model to charge the battery.
Any of these actions can cause the battery to burst
or leak and cause fire or injury as a result.
Use only the battery or AC power adapters
specified for use with this camera.
Do not use voltages other than the power supply
voltage shown.
The use of other power sources can cause a fire.
If the battery leaks and fluid gets in contact with
your eyes, skin or clothing. Flush the affected
area with clean water and seek medical attention
or call an emergency number right away.
Do not use the charger to charge batteries other
than those specified here.
The Ni-MH battery charger is designed for Fujifilm
HR-AA Ni-MH batteries. Using the charger to
charge conventional batteries or other types of
rechargeable batteries can cause the battery to
leak fluid, overheat or burst.
When carrying the battery, install it in a digital
camera or keep it in the hard case.
When storing the battery, keep it in the hard case.
When discarding, cover the battery terminals
with insulation tape.
Contact with other metallic objects or battery could
cause the battery to ignite or burst.
Keep Memory Cards out of the reach of small
children.
Because Memory Cards are small, they can be
swallowed by children. Be sure to store Memory
Cards out of the reach of small children. If a child
swallows a Memory Card, seek medical attention or
call an emergency number.
CAUTION
Unplug
from power
socket.
Do not use in
the bathroom
or shower
Do not
disassemble.
Do not use this camera in locations affected by
oil fumes, steam, humidity or dust.
This can cause a fire or electric shock.
Do not leave this camera in places subject to
extremely high temperatures.
Do not leave the camera in locations such as a
sealed vehicle or in direct sunlight.
This can cause a fire.
Keep out of the reach of small children.
This product could cause injury in the hands of a
child.
Do not place heavy objects on the camera.
This can cause the heavy object to tip over or fall
and cause injury.
Do not move the camera while the AC power
adapter is still connected.
Do not pull on the connection cord to
disconnect the AC power adapter.
This can damage the power cord or cables and
cause a fire or electric shock.
Do not use the AC power adapter when the plug is
damaged or the plug socket connection is loose.
This could cause a fire or electric shock.
Do not cover or wrap the camera or the AC
power adapter in a cloth or blanket.
This can cause heat to build up and distort the
casing or cause a fire.
When you are cleaning the camera or you do not
plan to use the camera for an extended period,
remove the battery and disconnect and unplug
the AC power adapter.
Failure to do so can cause a fire or electric shock.
When charging ends, unplug the charger from
the power socket.
Leaving the charger plugged into the power socket
can cause a fire.
Using a flash too close to a person’s eyes may
temporarily affect the eyesight.
Take particular care when photographing infants
and young children.
When an xD-Picture Card is removed, the card
could come out of the slot too quickly. Use your
finger to hold it and gently release the card.
Request regular internal testing and cleaning
for your camera.
Build-up of dust in your camera can cause a fire or
electric shock.
• Contact your FUJIFILM dealer to request internal
cleaning every 2 years.
• Please note this is not a free of charge service.
* Confirm your battery type before reading the
following descriptions.
The following explains proper use of batteries and
how to prolong their life. Incorrect use of batteries can
cause shorter battery life, as well as leakage,
excessive heat, fire or explosion.
1 Camera uses the Rechargeable Lithium-ion
Battery
* When shipped, the battery is not fully charged.
Always charge the battery before using it.
* When carrying the battery, install it in a
digital camera or keep it in the soft case.
■ Battery Features
• The battery gradually loses its charge even when
not used. Use a battery that has been charged
recently (in the last day or two) to take pictures.
• To maximize the life of the battery, turn the camera
off as quickly as possible when it is not being used.
• The number of available frames will be lower in cold
locations or at low temperatures. Take along a spare
fully charged battery. You can also increase the
amount of power produced by putting the battery in
your pocket or another warm place to heat it and
then loading it into the camera just before you take a
picture.
If you are using a heating pad, take care not to
place the battery directly against the pad. The
camera may not operate if you use a depleted
battery in cold conditions.
■ Charging the Battery
• You can charge the battery using the battery
charger (included).
• The battery can be charged at ambient
temperatures between 0°C and +40°C (+32°F
and +104°F). Refer to the OWNER’S MANUAL for
the time of charging battery.
• You should charge the battery at an ambient
temperature between +10°C and +35°C
(+50°F and +95°F). If you charge the battery at a
temperature outside this range, charging takes
longer because the performance of the battery is
impaired.
• You cannot charge the battery at temperatures of
0°C (+32°F) or below.
• The Rechargeable Lithium-ion Battery does not
need to be fully discharged or exhausted flat before
being charged.
• The battery may feel warm after it has been charged
or immediately after being used. This is perfectly
normal.
• Do not recharge a fully charged battery.
■ Battery Life
At normal temperatures, the battery can be used at
least 300 times. If the time for which the battery
provides power shortens markedly, this indicates that
the battery has reached the end of its effective life
and should be replaced.
■ Notes on storage
• If a battery is stored for long periods while charged,
the performance of the battery can be impaired. If
the battery will not be used for some time, run the
battery out before storing it.
• If you do not intend to use the camera for a long
period of time, remove the battery from the camera.
• Store the battery in a cool place.
• The battery should be stored in a dry location with
an ambient temperature between +15°C and
+25°C (+59°F and +77°F).
• Do not leave the battery in hot or extremely cold
places.
■ Using the AA-size Ni-MH batteries correctly
■ Handling the Battery
Cautions for Your Safety:
• Ni-MH batteries left unused in storage for long
periods can become “deactivated”. Also, repeatedly
• Do not carry or store battery with metal objects such
as necklaces or hairpins.
charging Ni-MH batteries that are only partially
discharged can cause them to suffer from the
• Do not heat the battery or throw it into a fire.
“memory effect”. Ni-MH batteries that are
• Do not attempt to take apart or change the battery.
“deactivated” or affected by “memory” suffer from
• Do not recharge the battery with chargers other
those specified.
the problem of only providing power for a short time
after being charged. To prevent this problem,
• Dispose of used battery promptly.
discharge and recharge them several times using
• Do not drop the battery or otherwise subject it to
strong impacts.
the camera’s “Discharging rechargeable batteries”
function.
• Do not expose the battery to water.
Deactivation and memory are specific to Ni-MH
• Always keep the battery terminals clean.
batteries and are not in fact battery faults.
• Do not store batteries in hot places. Also, if you use
the battery for a long period, the camera body and
See OWNER’S MANUAL for the procedure for
the battery itself will become warm. This is normal.
“Discharging rechargeable batteries”.
Use the AC power adapter if you are taking pictures
Do not use the “Discharging
or viewing images for a long period of time.
CAUTION
rechargeable batteries” function when
alkaline batteries being used.
2 Camera uses AA-size alkaline or Ni-MH
• To charge Ni-MH batteries, use the quick battery
(nickelmetal hydride) rechargeable batteries
charger (sold separately). Refer to the instructions
■ Applicable Batteries
supplied with the charger to make sure that the
• In the camera, use AA-size alkaline or Ni-MH
charger is used correctly.
(nickelmetal hydride) rechargeable batteries.
• Do not use the battery charger to charge other
Do not use AA-size manganese, nickel-cadmium
batteries.
(Ni-Cd) or lithium batteries in your camera because • Note that the batteries feel warm after being
the heat created by the batteries could damage the
charged.
camera or cause it not to work.
• Due to the way the camera is constructed, a small
(The UL recognized lithium battery can be used.)
amount of current is used even when the camera is
• The life of alkaline batteries varies between brands.
turned off. Note in particular that leaving Ni-MH
The life of batteries you purchase may be shorter
batteries in the camera for a long period will
than those provided with the camera.
overdischarge the batteries and may render them
unusable even after recharging.
■ Cautions for Using Battey
• Ni-MH batteries will self-discharge even when not
• Do not heat the batteries or throw them into a fire.
used, and the time for which they can be used may
• Do not carry or store batteries with metal objects
be shortened as a result.
such as necklaces or hairpins.
• Ni-MH batteries will deteriorate rapidly if
• Do not expose the batteries to water, and keep
overdischarged (e.g. by discharging the batteries in
batteries from getting wet or stored in moist
a flashlight). Use the “Discharging rechargeable
locations.
batteries” function provided in the camera to
• Do not attempt to take apart or change the
discharge the batteries.
batteries, including battery casings.
• Ni-MH batteries have a limited service life. If a
• Do not subject the batteries to strong impacts.
battery can only be used for a short time even after
• Do not use batteries that are leaking, deformed,
repeated discharge-charge cycles, it may have
discolored.
reached the end of its service life.
• Do not store batteries in warm or humid places.
• Keep the batteries out of reach of babies and small ■ Disposing of Batteries
children.
• When disposing of batteries, do so in accordance
• Make sure that the battery polarity (+ and ,) is
with your local waste disposal regulations.
correct.
3 Notes on both models ( 1 , 2 )
• Do not use new with used batteries. Do not use
charged and discharged batteries together.
■ AC Power Adapter
• Do not use different types or brands of batteries at
Always use the AC Power Adapter (sold separately)
the same time.
with the camera. The use of an AC Power adapter
• If you do not intend to use the camera for a long
other than FUJIFILM AC Power Adapter (sold
period of time, remove the batteries from the
separately) can be damaged to your digital camera.
camera. Note if the camera is left with the batteries
For details on the AC power adapter, refer to the
removed, the time and date settings are cleared.
OWNER’S MANUAL of your camera.
• The batteries feel warm right after being used.
• Use the AC power adapter for indoor use only.
Before removing the batteries, turn the camera off
• Plug the connection cord plug securely into the DC
and wait for the batteries to cool down.
input terminal.
• Since batteries do not work well in cold weather or
locations, warm the batteries by placing them inside • Turn off the FUJIFILM Digital camera before
disconnecting the cord from the DC input terminal.
your garments before use. Batteries do not work
To disconnect, pull out the plug gently. Do not pull
well when cold. They will work again when the
on the cord.
temperature returns to normal.
•
Do not use the AC power adapter with any device
• Soil (such as fingerprints) on the battery terminals
other than your camera.
makes the batteries charge less reducing the
• During use, the AC power adapter will become hot
number of images. Carefully wipe the battery
to the touch. This is normal.
terminals with a soft dry cloth before loading.
• Do not take apart the AC power adapter. Doing so
If any liquid at all leaks from the batteries, wipe
could be dangerous.
the battery compartment thoroughly and then
• Do not use the AC power adapter in a hot and
load new batteries.
humid place.
If any battery fluid comes into contact with your • Do not subject the AC power adapter to strong
shocks.
hands or clothing, flush the area thoroughly
• The AC power adapter may emit a humming. This is
with water. Note that battery fluid can cause
normal.
loss of eyesight if it gets into your eyes. If this
• If used near a radio, the AC power adapter may
occurs, do not rub your eyes. Flush the fluid
cause static. If this happens, move the camera
out with clean water and contact your
away from the radio.
physician for treatment.
Download PDF

advertising