BL01600-200
DIGITAL CAMERA
X10
Owner’s Manual
Thank you for your purchase of this
product. This manual describes how
to use your FUJIFILM digital camera and
the supplied software. Be sure that you
have read and understood its contents
and the warnings in “For Your Safety”
(P ii) before using the camera.
For information on related products, visit our website at
http://www.fujifilm.com/products/digital_cameras/index.html
EN
Before You Begin
First Steps
Basic Photography and Playback
More on Photography
More on Playback
Movies
Connections
Menus
Technical Notes
Troubleshooting
Appendix
For Your Safety
IMPORTANT SAFETY INSTRUCTIONS
• Read Instructions: All the safety and
operating instructions should be
read before the appliance is operated.
• Retain Instructions: The safety and
operating instructions should be
retained for future reference.
• Heed Warnings: All warnings on the
appliance and in the operating instructions should be adhered to.
• Follow Instructions: All operating
and use instructions should be followed.
Installation
Power Sources: This video product
should be operated only from the
type of power source indicated on
the marking label. If you are not sure
of the type of power supply to your
home, consult your appliance dealer
or local power company. For video
products intended to operate from
battery power, or other sources, refer
to the operating instructions.
Grounding or Polarization: This video
product is equipped with a polarized alternating-current line plug (a
plug having one blade wider than
the other). This plug will fit into the
power outlet only one way. This is a
safety feature. If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should
still fail to fit, contact your electrician
to replace your obsolete outlet. Do
ii
not defeat the safety purpose of the This video product should never be
placed near or over a radiator or heat
polarized plug.
register.
Alternate Warnings: This video
product is equipped with a 3-wire Attachments: Do not use attachments
grounding-type plug, a plug having not recommended by the video
a third (grounding) pin. This plug will product manufacturer as they may
only fit into a grounding-type power cause hazards.
outlet. This is a safety feature. If you
Water and Moisture: Do not use this
are unable to insert the plug into
video product near water – for exthe outlet, contact your electrician
ample, near a bath tub, wash bowl,
to replace your obsolete outlet. Do
kitchen sink, or laundry tub, in a wet
not defeat the safety purpose of the
basement, or near a swimming pool,
grounding-type plug.
and the like.
Overloading: Do not overload wall
Power-Cord Protection: Power-Supoutlets and extension cords as this
ply cords should be routed so that
can result in a risk of fire or electric
they are not likely to be walked on
shock.
or pinched by items placed upon
Ventilation: Slots and openings in the or against them, paying particular
cabinet are provided for ventilation attention to cords at plugs, conveand to ensure reliable operation of nience receptacles, and the point
the video product and to protect it where they exit from the appliance.
from overheating, and these openAccessories: Do not place this video
ings must not be blocked or covproduct on an unstable cart, stand,
ered.
tripod, bracket, or table. The video
The openings should never be
product may fall, causing serious inblocked by placing the video prodjury to a child or adult, and serious
uct on a bed, sofa, rug, or other simidamage to the appliance. Use only
lar surface.
with a cart, stand, tripod, bracket, or
This video product should not be
table recommended by the manuplaced in a built-in installation such
facturer, or sold with the video prodas a bookcase or rack unless proper
uct. Any mounting of the appliance
ventilation is provided or the manshould follow the manufacturer’s inufacturer’s instructions have been
structions, and should use a mountadhered to.
ing accessory recommended by the
manufacturer.
An
appliance
and cart combination should
be moved with
care. Quick stops,
excessive force,
and uneven surfaces may cause the appliance and
cart combination to overturn.
Antennas
Outdoor Antenna Grounding: If an
outside antenna or cable system is
connected to the video product, be
sure the antenna or cable system
is grounded so as to provide some
protection against voltage surges
and built-up static charges. Section
810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with respect to proper grounding
of the mast and supporting structure, grounding of the lead-in wire
to an antenna-discharge unit, size of
grounding conductors, location of
antenna-discharge unit, connection
to grounding electrodes, and requirements for the grounding electrode.
For Your Safety
Power Lines: An outside antenna system should not be located in the
vicinity of overhead power lines or
other electric light or power circuits,
or where it can fall into such power
lines or circuits. When installing an
outside antenna system, extreme
care should be taken to keep from
touching such power lines or circuits
as contact with them might be fatal.
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
Ground Clamp
Electric
Service
Equipment
Ground
Clamps
Power Service
Grounding Electrode
System (NEC ART 250.
PART H)
Antenna
Lead in Wire
Antenna
Discharge Unit
(NEC SECTION
810-20)
Grounding
Conductors
(NEC SECTION
810-21)
Use
Cleaning: Unplug this video product
from the wall outlet before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth
for cleaning.
Object and Liquid Entry: Never push
objects of any kind into this video
product through openings as they
may touch dangerous voltage
points or short out parts that could
result in a fire or electric shock. Never
spill liquid of any kind on the video
product.
Lightning: For added protection for
this video product receiver during
a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna
or cable system. This will prevent
damage to the video product due to
lightning and power-line surges.
Replacement Parts: When replacement parts are required, be sure
the service technician has used
replacement parts specified by the
manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may
result in fire, electric shock or other
Damage Requiring Service: Unplug this hazards.
video product from the wall outlet
and refer servicing to qualified ser- Safety Check: Upon completion of any
vice personnel under the following service or repairs to this video product, ask the service technician to
conditions:
When the power-supply cord or perform safety checks to determine
that the video product is in proper
plug is damaged.
If liquid has been spilled, or objects operating condition.
have fallen into the video product.
If the video product has been exposed to rain or water.
If the video product has been
dropped or the cabinet has been
damaged.
If the video product does not operate normally be following the
operating instructions. Adjust only
those controls that are covered by
the operating instructions as an improper adjustment of other controls
may result in damage and will often
require extensive work by a qualified
technician to restore the video product to its normal operation.
When the video product exhibits a
distinct change in performance - this
indicates a need for service.
Service
Servicing: Do not attempt to service
this video product yourself as opening or removing covers may expose
you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
iii
For Your Safety
Be sure to read this notes before using
Safety Notes
• Make sure that you use your camera correctly. Read these Safety Notes and
your Owner’s Manual carefully before use.
• After reading these Safety Notes, store them in a safe place.
WARNING
Do not allow water or foreign objects to enter the camera.
If water or foreign objects get inside the camera, turn the camera
off, remove the battery and disconnect and unplug the AC power
Avoid
adapter.
exposure to
Continued use of the camera can cause a fire or electric shock.
water
• Contact your FUJIFILM dealer.
About the Icons
The icons shown below are used in this document to indicate the severity of
the injury or damage that can result if the information indicated by the icon
is ignored and the product is used incorrectly as a result.
WARNING
CAUTION
This icon indicates that death or serious injury can result if the information is ignored.
This icon indicates that personal injury or material damage can result
if the information is ignored.
The icons shown below are used to indicate the nature of the information
which is to be observed.
Triangular icons tell you that this information requires attention (“important”).
Circular icons with a diagonal bar tell you that the action indicated is
prohibited (“Prohibited”).
Filled circles with an exclamation mark tell you an action that must be
performed (“Required”).
WARNING
If a problem arises, turn the camera off, remove the battery, disconnect and
unplug the AC power adapter.
Continued use of the camera when it is emitting smoke, is emitting
Unplug
any unusual odor, or is in any other abnormal state can cause a fire
from power
or electric shock.
socket.
• Contact your FUJIFILM dealer.
iv
Do not use in
the bathroom
or shower.
Do not disassemble
Do not use the camera in the bathroom or shower.
This can cause a fire or electric shock.
Never attempt to disassemble or modify (never open the case).
Failure to observe this precaution can cause fire or electric shock.
Should the case break open as the result of a fall or other accident, do not
touch the exposed parts.
Failure to observe this precaution could result in electric shock or in
Do not touch injury from touching the damaged parts. Remove the battery iminternal
mediately, taking care to avoid injury or electric shock, and take the
parts
product to the point of purchase for consultation.
Do not change, heat or unduly twist or pull the connection cord and do not
place heavy objects on the connection cord.
These actions could damage the cord and cause a fire or electric
shock.
• If the cord is damaged, contact your FUJIFILM dealer.
Do not place the camera on an unstable surface.
This can cause the camera to fall or tip over and cause injury.
Never attempt to take pictures while in motion.
Do not use the camera while you are walking or driving a vehicle. This
can result in you falling down or being involved in a traffic accident.
Do not touch any metal parts of the camera during a thunderstorm.
This can cause an electric shock due to induced current from the
lightning discharge.
Do not use the battery except as specified.
Load the battery as aligned with the indicator.
For Your Safety
WARNING
Do not heat, change or take apart the battery. Do not drop or subject the battery to impacts. Do not store the battery with metallic products. Do not use
chargers other than the specified model to charge the battery.
Any of these actions can cause the battery to burst or leak and cause
fire or injury as a result.
Use only the battery or AC power adapters specified for use with this camera.
Do not use voltages other than the power supply voltage shown.
The use of other power sources can cause a fire.
If the battery leaks and fluid gets in contact with your eyes, skin or clothing.
Flush the affected area with clean water and seek medical attention or call an
emergency number right away.
Do not use the charger to charge batteries other than those specified here.
The Ni-MH battery charger is designed for FUJIFILM HR-AA Ni-MH
batteries. Using the charger to charge conventional batteries or other
types of rechargeable batteries can cause the battery to leak fluid,
overheat or burst.
Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type.
When carrying the battery, install it in a digital camera or keep it in the hard
case. When storing the battery, keep it in the hard case. When discarding,
cover the battery terminals with insulation tape.
Contact with other metallic objects or battery could cause the battery to ignite or burst.
Keep Memory Cards out of the reach of small children.
Because Memory Cards are small, they can be swallowed by children.
Be sure to store Memory Cards out of the reach of small children. If
a child swallows a Memory Card, seek medical attention or call an
emergency number.
CAUTION
Do not use this camera in locations affected by oil fumes, steam, humidity or
dust.
This can cause a fire or electric shock.
Do not leave this camera in places subject to extremely high temperatures.
Do not leave the camera in locations such as a sealed vehicle or in
direct sunlight. This can cause a fire.
CAUTION
Keep out of the reach of small children.
This product could cause injury in the hands of a child.
Do not place heavy objects on the camera.
This can cause the heavy object to tip over or fall and cause injury.
Do not move the camera while the AC power adapter is still connected. Do not
pull on the connection cord to disconnect the AC power adapter.
This can damage the power cord or cables and cause a fire or electric
shock.
Do not use the AC power adapter when the plug is damaged or the plug socket
connection is loose.
This could cause a fire or electric shock.
Do not cover or wrap the camera or the AC power adapter in a cloth or blanket.
This can cause heat to build up and distort the casing or cause a fire.
When you are cleaning the camera or you do not plan to use the camera for
an extended period, remove the battery and disconnect and unplug the AC
power adapter.
Failure to do so can cause a fire or electric shock.
When charging ends, unplug the charger from the power socket.
Leaving the charger plugged into the power socket can cause a fire.
Using a flash too close to a person’s eyes may temporarily affect the eyesight.
Take particular care when photographing infants and young children.
When a memory card is removed, the card could come out of the slot too quickly. Use your finger to hold it and gently release the card.
Request regular internal testing and cleaning for your camera.
Build-up of dust in your camera can cause a fire or electric shock.
• Contact your FUJIFILM dealer to request internal cleaning every 2
years.
• Please note this is not a free of charge service.
Remove your fingers from the flash window before the flash fires.
Failure to observe this precaution could result in burns.
Keep the flash window clean and do not use the flash if the window is obstructed.
Failure to observe these precautions could cause smoke or discoloration.
v
For Your Safety
Power Supply and Battery
* Confirm your battery type before reading the following descriptions.
The following explains proper use of
batteries and how to prolong their
life. Incorrect use of batteries can
cause shorter battery life, as well as
leakage, excessive heat, fire or explosion.
1 Camera uses the Rechargeable
Lithium-ion Battery
* When shipped, the battery is not
fully charged. Always charge the
battery before using it.
* When carrying the battery, install it
in a digital camera or keep it in the
soft case.
■ Battery Features
• The battery gradually loses its
charge even when not used. Use
a battery that has been charged
recently (in the last day or two) to
take pictures.
• To maximize the life of the battery,
turn the camera off as quickly as
possible when it is not being used.
• The number of available frames will
be lower in cold locations or at low
temperatures. Take along a spare
fully charged battery. You can also
increase the amount of power produced by putting the battery in
your pocket or another warm place
to heat it and then loading it into
the camera just before you take a
picture.
vi
■ Battery Life
At normal temperatures, the battery can be used at least 300 times.
If the time for which the battery
provides power shortens markedly,
this indicates that the battery has
■ Charging the Battery
• You can charge the battery using reached the end of its effective life
and should be replaced.
the battery charger (included).
- The battery can be charged ■ Notes on storage
at ambient temperatures be- • If a battery is stored for long periods
tween 0°C and +40°C (+32°F
while charged, the performance of
and +104°F). Refer to the Owner’s
the battery can be impaired. If the
Manual for the time of charging
battery will not be used for some
battery.
time, run the battery out before
- You should charge the battery
storing it.
at an ambient temperature be- • If you do not intend to use the
tween +10°C and +35°C (+50°F
camera for a long period of time,
and +95°F). If you charge the
remove the battery from the cambattery at a temperature outside
era.
this range, charging takes longer • Store the battery in a cool place.
because the performance of the
- The battery should be stored in
battery is impaired.
a dry location with an ambient
- You cannot charge the battery
temperature between +15°C and
at temperatures of 0°C (+32°F) or
+25°C (+59°F and +77°F).
below.
- Do not leave the battery in hot or
• The Rechargeable Lithium-ion Batextremely cold places.
tery does not need to be fully dis■ Handling the Battery
charged or exhausted flat before
Cautions for Your Safety:
being charged.
• Do not carry or store battery with
• The battery may feel warm after it
metal objects such as necklaces or
has been charged or immediately
hairpins.
after being used. This is perfectly • Do not heat the battery or throw it
normal.
into a fire.
• Do not recharge a fully charged • Do not attempt to take apart or
battery.
change the battery.
If you are using a heating pad, take
care not to place the battery directly against the pad. The camera
may not operate if you use a depleted battery in cold conditions.
• Dispose of used battery promptly.
• Do not drop the battery or otherwise subject it to strong impacts.
• Do not expose the battery to water.
• Always keep the battery terminals
clean.
• Do not store batteries in hot places. Also, if you use the battery for
a long period, the camera body
and the battery itself will become
warm. This is normal. Use the AC
power adapter if you are taking
pictures or viewing images for a
long period of time.
2 Camera uses AA-size alkaline or Ni-MH
(nickel-metal hydride) rechargeable
batteries
* For details on the batteries that
you can use, refer to the Owner’s
Manual of your camera.
■ Cautions for Using Battery
• Do not heat the batteries or throw
them into a fire.
• Do not carry or store batteries with
metal objects such as necklaces or
hairpins.
• Do not expose the batteries to water, and keep batteries from getting
wet or stored in moist locations.
• Do not attempt to take apart or
change the batteries, including
battery casings.
• Do not subject the batteries to
strong impacts.
• Do not recharge the battery with
• Do not use batteries that are leakchargers other those specified.
ing, deformed, discolored.
For Your Safety
• Do not store batteries in warm or
If any liquid at all leaks from
humid places.
the batteries, wipe the battery
• Keep the batteries out of reach of
compartment thoroughly and
babies and small children.
then load new batteries.
• Make sure that the battery polarity
If any battery fluid comes into
(C and D) is correct.
contact with your hands or
• Do not use new with used batterclothing, flush the area thories. Do not use charged and disoughly with water. Note that
charged batteries together.
battery fluid can cause loss
• Do not use different types or
of eyesight if it gets into your
brands of batteries at the same
eyes. If this occurs, do not rub
time.
your eyes. Flush the fluid out
• If you do not intend to use the
with clean water and contact
camera for a long period of time,
your physician for treatment.
remove the batteries from the
camera. Note if the camera is left ■ Using the AA-size Ni-MH batteries
with the batteries removed, the
correctly
time and date settings are cleared. • Ni-MH batteries left unused in
• The batteries feel warm right afstorage for long periods can beter being used. Before removing
come “deactivated”. Also, repeatthe batteries, turn the camera off
edly charging Ni-MH batteries
and wait for the batteries to cool
that are only partially discharged
down.
can cause them to suffer from the
• Since batteries do not work well in
“memory effect”. Ni-MH batteries
cold weather or locations, warm
that are “deactivated” or affected
the batteries by placing them inby “memory” suffer from the probside your garments before use.
lem of only providing power for a
Batteries do not work well when
short time after being charged. To
cold. They will work again when
prevent this problem, discharge
the temperature returns to normal.
and recharge them several times
• Soil (such as fingerprints) on the
using the camera’s “Discharging
battery terminals makes the batrechargeable batteries” function.
teries charge less reducing the
Deactivation and memory are spenumber of images. Carefully wipe
cific to Ni-MH batteries and are not
the battery terminals with a soft
in fact battery faults.
dry cloth before loading.
See Owner’s Manual for the procedure for “Discharging rechargeable
batteries”.
CAUTION
Do not use the “Discharging rechargeable batteries” function when
alkaline batteries being used.
• To charge Ni-MH batteries, use the
quick battery charger (sold separately). Refer to the instructions
supplied with the charger to make
sure that the charger is used correctly.
• Do not use the battery charger to
charge other batteries.
• Note that the batteries feel warm
after being charged.
• Due to the way the camera is constructed, a small amount of current
is used even when the camera is
turned off. Note in particular that
leaving Ni-MH batteries in the
camera for a long period will overdischarge the batteries and may
render them unusable even after
recharging.
• Ni-MH batteries will self-discharge
even when not used, and the time
for which they can be used may be
shortened as a result.
• Ni-MH batteries will deteriorate
rapidly if over-discharged (e.g.
by discharging the batteries in a
flashlight). Use the “Discharging rechargeable batteries” function provided in the camera to discharge
the batteries.
• Ni-MH batteries have a limited
service life. If a battery can only
be used for a short time even after
repeated discharge-charge cycles,
it may have reached the end of its
service life.
■ Disposing of Batteries
• When disposing of batteries, do
so in accordance with your local
waste disposal regulations.
3 Notes on both models ( 1 , 2 )
■ AC Power Adapter
Always use the AC Power Adapter
with the camera. The use of an AC
Power adapter other than FUJIFILM
AC Power Adapter can be damaged
to your digital camera.
For details on the AC power adapter,
refer to the Owner’s Manual of your
camera.
• Use the AC power adapter for indoor use only.
• Plug the connection cord plug securely into the DC input terminal.
• Turn off the FUJIFILM Digital camera before disconnecting the cord
from the DC input terminal. To disconnect, pull out the plug gently.
Do not pull on the cord.
• Do not use the AC power adapter
with any device other than your
camera.
• During use, the AC power adapter
will become hot to the touch. This
is normal.
vii
For Your Safety
• Do not take apart the AC power
adapter. Doing so could be dangerous.
• Do not use the AC power adapter
in a hot and humid place.
• Do not subject the AC power
adapter to strong shocks.
• The AC power adapter may emit a
humming. This is normal.
• If used near a radio, the AC power
adapter may cause static. If this
happens, move the camera away
from the radio.
Before Using the Camera
Do not aim the camera at extremely
bright light sources, such as the sun
in a cloudless sky. Failure to observe
this precaution could damage the
camera image sensor.
■ Test Shots Prior to Photography
For important photographs (such as
weddings and overseas trips), always
take a test shot and view the image to make sure that the camera is
working normally.
• FUJIFILM Corporation cannot accept liability for any incidental
losses (such as the costs of photography or the loss of income from
photography) incurred as a result
of faults with this product.
■ Notes on Copyright
Images recorded using your digital
camera system cannot be used in
ways that infringe copyright laws
without the consent of the owner,
viii
Although the LCD panel is produced ■ Explanation of Color Television
System
with highly sophisticated technologies, there may be black spots or NTSC: National Television System
Committee, color television
permanently lit spots. This is not a
telecasting
specifications
malfunction, and does not affect readopted mainly in the U.S.A.,
corded images.
Canada and Japan.
■ Trademark Information
xD-Picture Card and E are trade- PAL: Phase Alternation by Line, a
color television system admarks of FUJIFILM Corporation. The
opted mainly by European
typefaces included herein are solely
countries and China.
developed by DynaComware Tai■ Handling Your Digital Camera
wan Inc. Macintosh, QuickTime, and
To ensure that images are recorded Mac OS are trademarks of Apple Inc. ■ Exif Print (Exif ver. 2.3)
correctly, do not subject the camera in the U.S.A. and other countries. Exif Print Format is a newly revised
to impact or shock while an image is Windows 7, Windows Vista, and the digital camera file format that conbeing recorded.
Windows logo are trademarks of tains a variety of shooting informathe Microsoft group of companies. tion for optimal printing.
■ Liquid Crystal
Adobe and Adobe Reader are either
If the LCD monitor is damaged, take
IMPORTANT NOTICE: Read Before
trademarks or registered trademarks
particular care with the liquid crystal
Using the Software
of Adobe Systems Incorporated in
in the monitor. If any of the followthe U.S.A. and/or other countries. Direct or indirect export, in whole or
ing situations arise, take the urgent
The SDHC and SDXC logos are trade- in part, of licensed software without
action indicated.
marks of SD-3C, LLC. The HDMI logo the permission of the applicable
• If liquid crystal comes in contact
is a trademark. YouTube is a trade- governing bodies is prohibited.
with your skin:
mark of Google Inc. All other trade
Wipe the area with a cloth and
names mentioned in this manual are
then wash thoroughly with soap
the trademarks or registered tradeand running water.
marks of their respective owners.
• If liquid crystal gets into your eye:
Flush the affected eye with clean ■ Notes on Electrical Interference
water for at least 15 minutes and If the camera is to be used in hosthen seek medical assistance.
pitals or aircrafts, please note that
• If liquid crystal is swallowed:
this camera may cause interference
Flush your mouth thoroughly with to other equipment in the hospital
water. Drink large quantities of wa- or aircraft. For details, please check
ter and induce vomiting. Then seek with the applicable regulations.
medical assistance.
unless intended only for personal
use. Note that some restrictions apply to the photographing of stage
performances, entertainments and
exhibits, even when intended purely
for personal use. Users are also asked
to note that the transfer of Memory
Card containing images or data protected under copyright laws is only
permissible within the restrictions
imposed by those copyright laws.
For Your Safety
NOTICES
To prevent fire or shock hazard, do not expose the unit
to rain or moisture.
Please read the “Safety Notes” and make sure you understand them before using the camera.
Perchlorate Material—special handling may apply. See
http://www.dtsc.ca.gov/hazardouswaste/perchlorate.
For Customers in the U. S. A.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
FCC Statement: This device complies with Part 15 of the
FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
CAUTION: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• You are cautioned that any changes or modifications In Countries Outside the European Union, Norway, Iceland and
not expressly approved in this manual could void the Liechtenstein: If you wish to discard this product, including the batteries or accumulators, please contact your
user’s authority to operate the equipment.
local authorities and ask for the correct way of disposal.
Notes on the Grant: To comply with Part 15 of the FCC
Rules, this product must be used with a Fujifilm-spec- EC Declaration of Conformity
ified ferrite-core A/V cable, USB cable, and DC supply We
cord.
Name:
FUJIFILM Electronic Imaging Europe GmbH
Address:
Benzstrasse 2 47533 Kleve, Germany
For Customers in Canada
declare that the product
CAUTION: This Class B digital apparatus complies with Product Name: FUJIFILM DIGITAL CAMERA X10
Canadian ICES-003.
Manufacturer’s
Name:
FUJIFILM Corporation
Disposal of Electrical and Electronic Equipment in Private
Manufacturer’s 7-3, AKASAKA 9-CHOME, MINATO-KU,
Households
Address:
TOKYO, 107-0052 JAPAN
In the European Union, Norway, Iceland and Liechconforms to the following Standards:
tenstein: This symbol on the product, or in
Safety:
EN60065: 2002 + A1: 2006 + A11: 2008
the manual and in the warranty, and/or on
EMC:
EN55022: 2006 + A1: 2007 Class B
its packaging indicates that this product
EN55024: 1998 + A1: 2001 + A2: 2003
shall not be treated as household waste.
EN61000-3-2: 2006
Instead it should be taken to an applicable
EN61000-3-3: 2008
collection point for the recycling of electrical and electronic equipment.
following the provision of the EMC Directive (2004/108/EC)
By ensuring this product is disposed of correctly, you and Low Voltage Directive (2006/95/EC).
will help prevent potential negative consequences to
the environment and human health, which could otherwise be caused by inappropriate waste handling of
this product.
This symbol on the batteries or accumulators indicates that those batteries shall not
be treated as household waste.
Kleve,
Germany
Place
October 1, 2011
Date
Signature, Managing
Director
If your equipment contains easy removable batteries or
accumulators please dispose these separately according to your local requirements.
The recycling of materials will help to conserve natural
resources. For more detailed information about recycling this product, please contact your local city office,
your household waste disposal service or the shop
where you purchased the product.
ix
About This Manual
Before using the camera, read this manual and the warnings on pages ii–ix. For information on specific
topics, consult the sources below.
✔ Table of Contents .............................................. P xi ✔ Troubleshooting .............................................P
.............................................P 111
The “Table of Contents” gives an overview of the Having a specific problem with the camera? Find
entire manual. The principal camera operations the answer here.
are listed here.
✔ Warning Messages and Displays ..................... P 116
Find out what’s behind that flashing icon or error
message in the display.
Memory Cards
Pictures can be stored in the camera’s internal memory or on optional SD, SDHC, and SDXC memory cards
(P 14), referred to in this manual as “memory cards”.
Temperature Warning
The camera will turn off automatically before its temperature or the temperature of the battery rise above safe
limits. Pictures taken when a temperature warning is displayed may exhibit higher levels of “noise” (mottling).
Turn the camera off and wait for it to cool before turning it on again.
Camera body care
For continued enjoyment of your camera, use a soft, dry cloth to clean the camera body after each use. Do not
use alcohol, thinner, or other volatile chemicals, which could discolor or deform the leather on the camera body.
Any liquid on the camera should be removed immediately with a soft, dry cloth.
x
Table of Contents
For Your Safety ................................................................................. ii
IMPORTANT SAFETY INSTRUCTIONS ...................................... ii
Safety Notes .................................................................................... iv
About This Manual .......................................................................... x
Before You Begin
Introduction ....................................................................................... 1
Symbols and Conventions .......................................................... 1
Supplied Accessories .................................................................... 1
Parts of the Camera ....................................................................... 2
Camera Displays .......................................................................... 5
First Steps
Attaching the Strap ........................................................................ 8
Charging the Battery ...................................................................10
Inserting the Battery and a Memory Card ......................... 11
Turning the Camera on and Off ..............................................15
Basic Setup ....................................................................................... 17
Basic Photography and Playback
Taking Pictures ...............................................................................18
Viewing Pictures ............................................................................22
More on Photography
Shooting Mode ...............................................................................23
P: PROGRAM AE ............................................................................24
S: SHUTTER PRIORITY AE ...........................................................25
A: APERTURE PRIORITY AE ........................................................25
M: MANUAL ....................................................................................26
C1/C2: CUSTOM MODE ..............................................................27
EXR (E AUTO/E Priority) .......................................28
B AUTO ..........................................................................................29
Adv. ADVANCED...........................................................................29
SP SCENE POSITION ....................................................................33
Focus Lock.........................................................................................34
The AFL/AEL Button ..........................................................................35
Locking Exposure ......................................................................35
Locking Focus .............................................................................35
F Macro and Super Macro Modes (Close-ups) ................36
N Using the Flash (Super-Intelligent Flash) .......................37
J Using the Self-Timer ...............................................................39
Continuous Shooting (Burst Mode/Bracketing)..............40
d Exposure Compensation .....................................................44
Metering ............................................................................................45
Focus Mode ......................................................................................46
Focus Frame Selection ................................................................48
White Balance..................................................................................49
The Fn Button ..................................................................................51
b Intelligent Face Detection ..................................................52
n Face Recognition ....................................................................53
Adding New Faces .......................................................................53
Viewing, Editing, and Deleting Existing Data ...................54
Taking RAW pictures ....................................................................55
More on Playback
Playback Options ...........................................................................56
Continuous Shooting .................................................................56
I Favorites: Rating Pictures ....................................................56
Playback Zoom..............................................................................57
Multi-Frame Playback .................................................................58
A Deleting Pictures ....................................................................59
Viewing Photo Information ......................................................60
Image Search ...................................................................................61
xi
Table of Contents
X PhotoBook Assist ...................................................................62
Creating a PhotoBook ................................................................62
Viewing PhotoBooks ..................................................................63
Editing and Deleting PhotoBooks .........................................63
Viewing Panoramas......................................................................64
Movies
Recording Movies ..........................................................................65
Movie Frame Size .........................................................................66
a Viewing Movies........................................................................67
Connections
Viewing Pictures on TV ...............................................................68
Printing Pictures via USB............................................................70
Connecting the Camera ............................................................70
Printing Selected Pictures ........................................................70
Printing the DPOF Print Order.................................................71
Creating a DPOF Print Order ....................................................73
Viewing Pictures on a Computer ............................................76
Installing the Software ...............................................................76
Connecting the Camera ............................................................80
Menus
Using the Menus: Shooting Mode .........................................82
Using the Shooting Menu .........................................................82
Shooting Menu Options ............................................................82
A E MODE ..........................................................................82
A Adv. MODE ..............................................................................82
A SCENE POSITION .....................................................................82
N ISO ...............................................................................................82
O IMAGE SIZE...............................................................................83
xii
T IMAGE QUALITY .....................................................................84
U DYNAMIC RANGE ..................................................................84
P FILM SIMULATION .................................................................85
d WB SHIFT ..................................................................................85
f COLOR........................................................................................85
H SHARPNESS ..............................................................................85
r HIGHLIGHT TONE ..................................................................85
s SHADOW TONE ......................................................................85
h NOISE REDUCTION................................................................85
R INTELLIGENT DIGITAL ZOOM ............................................86
Z ADVANCED ANTI BLUR ........................................................86
b FACE DETECTION...................................................................86
F AF MODE...................................................................................86
n FACE RECOGNITION..............................................................87
I FLASH.........................................................................................87
g EXTERNAL FLASH ..................................................................87
K CUSTOM SET............................................................................87
v DISP. CUSTOM SETTING ......................................................88
W MOVIE MODE ..........................................................................88
F AF MODE (F mode) ............................................................88
Using the Menus: Playback Mode ..........................................89
Using the Playback Menu..........................................................89
Playback Menu Options.............................................................89
X PHOTOBOOK ASSIST............................................................89
b IMAGE SEARCH .......................................................................89
x ERASE .........................................................................................89
j MARK FOR UPLOAD TO .......................................................89
I SLIDE SHOW ............................................................................90
j RAW CONVERSION ................................................................91
B RED EYE REMOVAL ................................................................92
D PROTECT ...................................................................................92
Table of Contents
G CROP ..........................................................................................93
O RESIZE ........................................................................................93
C IMAGE ROTATE........................................................................94
E COPY...........................................................................................94
F VOICE MEMO ...........................................................................95
n ERASE FACE RECOG. .............................................................95
K PRINT ORDER (DPOF) ...........................................................95
J DISP. ASPECT ...........................................................................96
The Setup Menu .............................................................................97
Using the Setup Menu................................................................97
Setup Menu Options...................................................................98
F DATE/TIME ...............................................................................98
N TIME DIFFERENCE ..................................................................98
L a .................................................................................98
o SILENT MODE ..........................................................................98
R RESET .........................................................................................99
K FORMAT ....................................................................................99
A IMAGE DISP. .............................................................................99
B FRAME NO. ............................................................................ 100
G OPERATION VOL. ................................................................ 100
H SHUTTER VOLUME ............................................................. 100
e SHUTTER SOUND................................................................ 100
I PLAYBACK VOLUME ............................................................101
J LCD BRIGHTNESS .................................................................101
M AUTO POWER OFF ...............................................................101
1 QUICK START MODE...........................................................101
F Fn BUTTON ............................................................................101
L DUAL IS MODE ......................................................................101
B RED EYE REMOVAL ..............................................................102
C AF ILLUMINATOR .................................................................102
k AE/AF-LOCK MODE .............................................................102
v AE/AF-LOCK BUTTON ........................................................102
j RAW ..........................................................................................102
j FOCUS CHECK .......................................................................102
I FOCUS CONTROL DIAL ..................................................... 103
M FOCUS SCALE UNITS ......................................................... 103
z FRAMING GUIDLINE .......................................................... 103
J COLOR SPACE ....................................................................... 104
t SAVE ORG IMAGE ................................................................ 104
m AUTOROTATE PB ................................................................. 104
O BACKGROUND COLOR ...................................................... 104
c GUIDANCE DISPLAY........................................................... 104
Q VIDEO SYSTEM..................................................................... 104
S CUSTOM RESET ................................................................... 105
x POWER MANAGEMENT .................................................... 105
Technical Notes
Optional Accessories................................................................. 106
Accessories from FUJIFILM .....................................................107
Attaching the Lens Hoods ..................................................... 109
Attaching the Filters
(available from third-party suppliers) ............................... 109
Caring for the Camera ...............................................................110
Troubleshooting
Problems and Solutions ........................................................... 111
Warning Messages and Displays ..........................................116
Appendix
Internal Memory/Memory Card Capacity ........................120
Specifications ................................................................................121
Restrictions on Camera Settings ..........................................126
Shooting Mode and Camera Settings ................................126
xiii
Memo
xiv
Introduction
Symbols and Conventions
Menus and other text in the camera monitor are shown in bold. In the illustrations in this manual, the
monitor display may be simplified for explanatory purposes.
Before You Begin
The following symbols are used in this manual:
3 : This information should be read before use to ensure correct operation.
1 : Points to note when using the camera.
2 : Additional information that may be helpful when using the camera.
P: Other pages in this manual on which related information may be found.
Supplied Accessories
The following items are included with the camera:
NP-50 rechargeable battery
BC-45W battery charger
USB cable
Lens cap
• Owner’s Manual
(this manual)
• Shoulder strap
• Protective covers (× 2)
CD-ROM
Clip attaching tool
Metal strap clips (× 2)
1
Introduction
Parts of the Camera
For more information, refer to the page listed to the right of each item.
1
2
3
4
5
6
7
8
9
2
Shutter button ...........................................20 10 Zoom ring .....................................................19 18 Terminal cover............................68, 70, 80
Exposure compensation dial ........... 44
ON/OFF switch ..........................................15 19 DC coupler cable cover..................... 107
Mode dial ......................................................23 11 Lens .................................................................110 20 Battery-chamber cover latch............ 11
Microphone (L/R) .....................................65 12 AF-assist illuminator ............................ 102 21 Battery-chamber cover ........................ 11
Hot shoe ..............................................87, 106
Self-timer lamp ..........................................39 22 Speaker ....................................................67, 95
Viewfinder window .................................. 6 13 Fn (Function) button ..............................51 23 Tripod mount
Flash..................................................................37 14 Battery latch .........................................11, 13 24 Monitor ............................................................. 5
Strap eyelet .................................................... 8 15 Memory card slot .....................................12 25 USB cable connector .............68, 70, 80
Focus mode selector .............................46 16 Battery chamber ....................................... 11 26 Connector for HDMI cable .................68
17 Main-command dial................................. 4
Introduction
Diopter adjustment control ................ 4
N (flash pop-up) switch .......................37
a (playback) button .......................... 15, 22
AE (autoexposure) button ............................45
k (playback zoom in) button .....................57
31 AF (autofocus) button...................................48
n (playback zoom out) button ..................57
32 WB (white balance) button ..........................49
33 Indicator lamp ............................................21
34 AFL/AEL (autoexposure/autofocus lock) button ............................................................. 35, 47
35 Selector button (see below)
36 Sub-command dial ................................... 4
37 RAW button...................................................55
38 DISP (display)/BACK button .................6, 21
The Selector Button
Move cursor up (e)
DRIVE button (P 40)/
b (delete) button (P 22)
Before You Begin
27
28
29
30
MENU/OK button (P 17)
Move cursor left (g)
F (macro) button (P 36)
Move cursor right (h)
N (flash) button (P 37)
Move cursor down (f)
h (self-timer) button (P 39)
3
Introduction
Main-command dial/Sub-command dial
Rotate the main/sub-command dial to set the aperture value or shutter speed. You can also select items
using the main/sub-command dial for the selector
button. To adjust focus for MF, rotate the sub-command dial (P 46).
Main-command
dial
Sub-command
dial
Press the center of the main-command
dial for some operations such as switching the setting item in M mode.
4
Control Lock
To lock the RAW button and selector button (DRIVE/
N/h/F), press MENU/OK until X is displayed. This
prevents accidental operation during shooting. The
controls can be unlocked by pressing MENU/OK until
X is no longer displayed.
Diopter adjustment control
The camera is equipped with diopter adjustment to
accommodate individual differences in vision. Slide
the diopter adjustment control up and down until the
viewfinder display is in sharp focus.
Introduction
■ Shooting
1
2
3
4
5
6
7
8
9
1000 F3.3
10
11
* a: indicates that no memory card 12
is inserted and that pictures will 13
be stored in the camera’s internal 14
memory (P 12).
15
100
F
Flash mode...................................................37
Macro (close-up) mode........................36
Self-timer indicator .................................39
Continuous shooting mode .............40
Advanced Anti Blur .........................29, 86
White balance ............................................49
Film simulation ..........................................85
Dynamic range ......................................... 84
Internal memory indicator *
Number of available frames ........... 120
Image size/quality ...........................83, 84
Temperature warning ....................x, 116
Blur warning ......................................38, 116
Electronic level ..........................................88
Dual IS mode ........................................... 101
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Focus warning .................................20, 116
Silent mode indicator .................... 21, 98
Distance indicator....................................46
Battery level .................................................16
Sensitivity ......................................................82
Aperture.................................................25, 26
AE lock indicator .......................................35
Shutter speed .....................................25, 26
Metering ........................................................45
Shooting mode .........................................23
Manual focus indicator .........................46
Exposure indicator ................................. 44
Histogram ....................................................... 7
Focus frame .................................................34
Intelligent digital zoom ........................86
1 Favorites .........................................................56
2 Intelligent Face Detection
indicator .................................................52, 92
3 Red-eye removal indicator.................92
4 Pro focus mode, pro low-light
mode ........................................................31, 32
5 Motion panorama z ..................30, 64
6 Frame number ........................................100
7 Gift image .....................................................56
8
9
10
11
12
13
14
15
16
Dynamic range ......................................... 84
E mode ..............................................28
Playback mode indicator ............22, 56
Portrait enhancer .....................................33
Mark for upload to...................................89
Photobook assist ......................................62
Voice memo indicator...........................95
DPOF print indicator ..............................71
Protected image .......................................92
Before You Begin
Camera Displays
The following indicators may appear during shooting and playback. The indicators displayed vary with
camera settings.
■ Playback
100-0001
4:3 F
YouTube
12/31/2050 10:00 AM
1/1000
F2.8
+1 1
3
5
Introduction
■ Display mode
Press DISP/BACK to cycle through display modes as follows:
• Shooting
Custom Display
Choose items for display using v DISP. CUSTOM
SETTING in the shooting menu (P 88).
000100
2
1
F
-1
-2
P 1
2000
5.6
F
200
2000
INFO DISPLAY
LCD SWITCHED OFF
200
INFORMATION OFF
100
F5.6
CUSTOM
6
F5.6
STANDARD
2000
3
While INFO DISPLAY or LCD SWITCHED OFF is selected, the display mode may turn to STANDARD depending on the operations.
200
F
Optical Viewfinder
This display is immune from digital video effects and
allows the subject to be viewed directly with no display lag. Subjects are always in focus, allowing you to
check their expression at any time.
c
• No information is displayed.
• The display in the viewfinder may differ slightly
from the final photograph due to parallax.
• The frame coverage is approximately 85% (when aspect ratio is 4:3).
• You may see part of the lens through the viewfinder
depending on the zoom position.
Introduction
• Playback
4:3 F
YouTube
1/1000
F2.8
+1 1
3
INFORMATION ON
INFORMATION OFF
100-0001
100-0001
4:3 N
ISO 400
F4.5
1/250
:
: OFF
:
: -1 2 3
12/31/2050 10 : 00 AM
DETAIL INFORMATION
3:2 F
12/31/2050
1 / 1000
10 : 00 AM
F4.5
-1 2 3 200
I FAVORITES
No. of
pixels
12/31/2050 10:00 AM
Pixel brightness
Shadows
Highlights
Optimal exposure: Pixels are
distributed in an even curve
throughout the tone range.
Overexposed: Pixels are clustered
at the right side of the graph.
Before You Begin
Histograms
Histograms show the distribution of tones in the image. Brightness is shown by the horizontal axis, the
number of pixels by the vertical axis.
100-0001
Underexposed: Pixels are clustered
at the left side of the graph.
7
Attaching the Strap
Attach the strap clips to the camera and then attach the strap.
Open a strap clip.
Pass the clip through the eyelet.
Use the clip attaching tool to open a strap
Rotate the clip fully
clip as shown.
through the eyelet until it
clicks closed.
1
3
First Steps
a protective cover.
4 Attach
Place a protective cover over the eyelet as
3
Keep the tool in a safe place. You will need it to
open the strap clips when removing the strap.
the strap clip on an eyelet.
2 Place
Hook the strap eyelet in the clip opening.
Remove the tool, using the other hand to
keep the clip in place.
8
shown, with the black side of the cover toward the camera. Repeat Steps 1–4 for the
second eyelet.
Attaching the Strap
the strap.
5 Insert
Insert the strap through a protective cover
and strap clip.
the strap.
6 Fasten
Fasten the strap as shown. Repeat Steps 5–6
for the second eyelet.
First Steps
3
To avoid dropping the camera, be sure the strap is correctly secured.
9
Charging the Battery
The battery is not charged at shipment. Charge the battery before use.
Place the battery in the supplied battery
Plug the charger in.
charger.
Plug the charger into an indoor power outInsert the battery in the orientation indicatlet. The charging indicator will light.
ed by the DFC labels.
The Charging Indicator
1
2
The camera uses an NP-50 rechargeable battery.
Charge lamp
Arrow
The charging indicator shows battery charge
status as follows:
Charging
indicator
On
Battery not
inserted.
Battery fully
charged.
Battery charging.
Blinks
Battery fault.
Battery
Off
DFC
label
Battery charger
DFC label
Battery status
Action
Insert the battery.
Remove the battery.
—
Unplug the charger and
remove the battery.
the battery.
3 Charge
Remove the battery when charging is complete. See the specifications (P 124) for
charging times (note that charging times increase at low temperatures).
3
Unplug the charger when it is not in use.
10
Inserting the Battery and a Memory Card
Although the camera can store pictures in internal memory, optional SD, SDHC, and SDXC memory
cards (sold separately) can be used to store additional pictures. After charging the battery, insert the
battery and memory card as described below.
1 Open the battery-chamber cover.
the orange battery latch and slide the battery into the camera, keeping the battery
latch pressed to one side. Confirm that the
battery is securely latched.
First Steps
the battery.
2 Insert
Align the orange stripe on the battery with
Orange stripe
a
Be sure the camera is off before opening the battery-chamber cover.
3
• Do not open the battery-chamber cover when
the camera is on. Failure to observe this precaution could result in damage to image files or
memory cards.
• Do not use excessive force when handling the
battery-chamber cover.
Battery latch
3
Insert the battery in the correct orientation. Do
NOT use force or attempt to insert the battery upside down or backwards. The battery will slide in
easily in the correct orientation.
11
Inserting the Battery and a Memory Card
the memory card.
3 Insert
Holding the memory card in the orientation shown at
right, slide it in until
it clicks into place
at the back of the
slot.
Click
• SD/SDHC/SDXC memory
cards can be locked, making it impossible to format
the card or to record or Write-protect
delete images. Before in- switch
serting an SD/SDHC/SDXC
memory card, slide the write-protect switch to
the unlocked position.
4 Close the battery-chamber cover.
3
• Be sure card is in the correct orientation; do not
insert at an angle or use force. If the memory
card is not correctly inserted or no memory
card is inserted, a will appear in the LCD monitor and internal memory will be used for recording and playback.
12
Inserting the Battery and a Memory Card
Removing the Battery and Memory Card
Before removing the battery or memory card, turn
the camera off and open the battery-chamber cover.
To remove the battery, press the
battery latch to the side, and
slide the battery out of the camera as shown.
Battery latch
To remove the memory card,
press it in and release it slowly.
The card can then be removed
by hand. When a memory card
is removed, the card could come out of the slot too
quickly. Use your finger to hold it and gently release
the card.
First Steps
3 Batteries
• Remove dirt from the battery terminals with a clean,
dry cloth. Failure to observe this precaution could
prevent the battery from charging.
• Do not affix stickers or other objects to the battery.
Failure to observe this precaution could make it impossible to remove the battery from the camera.
• Do not short the battery terminals. The battery could
overheat.
• Read the cautions in “Power Supply and Battery”
(P vi).
• Use only battery chargers designated for use with the
battery. Failure to observe this precaution could result in product malfunction.
• Do not remove the labels from the battery or attempt
to split or peel the outer casing.
• The battery gradually loses its charge when not in
use. Charge the battery one or two days before use.
b Using an AC Power Adapter
• The camera can be powered by an optional AC power adapter and DC coupler (sold separately). See the
manuals provided with the AC power adapter and DC
coupler for details.
• Depending on the country or region of sale, a demo
mode slide show may start if the camera is turned on
while powered by an AC power adapter. Press the
shutter button to end the show.
13
Inserting the Battery and a Memory Card
■ Compatible Memory Cards
FUJIFILM and SanDisk SD, SDHC, and SDXC memory cards have been approved for use in the camera. A complete list of approved memory cards
is available at http://www.fujifilm.com/support/
digital_cameras/compatibility/. Operation is not
guaranteed with other cards. The camera can not
be used with xD-Picture Cards or MultiMediaCard
(MMC) devices.
3 Memory Cards
• Do not turn the camera off or remove the memory
card while the memory card is being formatted or
data are being recorded to or deleted from the card.
Failure to observe this precaution could damage the
card.
• Format SD/SDHC/SDXC memory cards before first
use, and be sure to reformat all memory cards after using them in a computer or other device. For
more information on formatting memory cards, see
“K FORMAT” (P 99).
• Memory cards are small and can be swallowed; keep
out of reach of children. If a child swallows a memory
card, seek medical assistance immediately.
14
• miniSD or microSD adapters that are larger or smaller
than the standard dimensions of an SD/SDHC/SDXC
card may not eject normally; if the card does not
eject, take the camera to an authorized service representative. Do not forcibly remove the card.
• Do not affix labels to memory cards. Peeling labels
can cause camera malfunction.
• Movie recording may be interrupted with some types
of SD/SDHC/SDXC memory card. Use a G card
or better when shooting HD or high-speed movies.
• The data in internal memory may be erased or corrupted when the camera is repaired. Please note that
the repairer will be able to view pictures in internal
memory.
• Formatting a memory card or internal memory in the
camera creates a folder in which pictures are stored.
Do not rename or delete this folder or use a computer or other device to edit, delete, or rename image
files. Always use the camera to delete pictures from
memory cards and internal memory; before editing
or renaming files, copy them to a computer and edit
or rename the copies, not the originals.
Turning the Camera on and Off
To turn the camera on, rotate the zoom ring as
shown.
Turning the Camera on in Playback Mode
To turn the camera on and begin playback, press the
a button for about a second.
First Steps
Rotate the zoom ring to OFF to turn the camera
off.
b Switching to Playback Mode
Press the a button to start playback. Press a button
again or press the shutter button halfway to return to
shooting mode.
Press the a button again to turn the camera off.
c
The camera does not exit to shooting mode when
pressing the shutter button.
c
• If the zoom ring is not fully rotated to OFF, the battery
will drain.
• Pictures can be affected by fingerprints and other
marks on the lens. Keep the lens clean.
15
Turning the Camera on and Off
b Auto Power Off
The camera will turn off automatically if no operations
are performed for the length of time selected in the
M AUTO POWER OFF menu (P 101). To reactivate
the camera after it has turned off automatically, rotate
the zoom ring to OFF and then turn the camera on.
16
Battery Level
Battery level is shown as follows:
Indicator
Description
D (white) Battery partially discharged.
C (white) Battery more than half discharged.
Low battery. Charge as soon as posB (red)
sible.
Battery exhausted. Turn camera off
A (blinks red)
and charge battery.
Basic Setup
A language-selection dialog is displayed the first time the camera is turned on. Set up the camera as
described below (for information on resetting the clock or changing languages, see page 98).
1 Highlight a language and press MENU/OK.
START MENU
SET
1
Press DISP/BACK to skip the current step. Any steps you skip will be displayed
the next time the camera is turned on.
NO
The date and time will be displayed. Press the selector left or right to
2 highlight
the year, month, day, hour, or minute and press up or down
DATE / TIME NOT SET
2013
2012
YY. MM. DD
SET
2011
2010
2009
1. 1
NO
12 : 00
AM
First Steps
ENGLISH
FRANCAIS
DEUTSCH
ESPAÑOL
PORTUGUÊS
to change. To change the order in which the year, month, and day
are displayed, highlight the date format and press the selector up or
down. Press MENU/OK when settings are complete.
management options will be displayed. Press the selector up
3 Power
or down to highlight one of the following options and then press
MENU/OK:
• n POWER SAVE: Save battery power.
• o CLEAR DISPLAY: Choose for a brighter, higher quality display.
2 The Camera Clock
If the battery is removed for an extended period, the camera clock will be reset and the language-selection dialog
will be displayed when the camera is turned on.
17
Taking Pictures
This section explains basic photography.
a mode.
1 Select
When you rotate the mode dial to EXR, the R display will appear in the LCD monitor.
Scene Icon (P 28)
The camera automatically selects the appropriate scene.
Basic Photography and Playback
18
The o Icon
In R mode, the camera continuously adjusts focus and searches for faces, increasing the drain on the
battery. o is displayed in the LCD monitor.
1
• The camera analyses the scene and selects the preferred E mode when the shutter button is pressed
halfway (P 29).
• To raise the flash when lighting is poor, press the flash pop-up switch (P 37).
Taking Pictures
the picture.
2 Frame
Use the zoom ring
to
frame the picture in the
display. The zoom indicator appears.
Zoom ring
2 Focus Lock
Use focus lock (P 34) to focus on subjects that are not
in the focus frame.
To prevent pictures that are
out of focus or too dark (underexposed), keep your fingers and other objects away
from the lens and flash.
Basic Photography and Playback
Zoom indicator
Holding the Camera
Hold the camera steady with
both hands and brace your
elbows against your sides.
Shaking or unsteady hands
can blur your shots.
19
Taking Pictures
Focus.
3 Press
the shutter button halfway
to focus.
2 The Shutter Button
The shutter button has two positions. Pressing the
shutter button halfway (q) sets focus and exposure;
to shoot, press the shutter button the rest of the way
down (w).
If the camera is able to focus, it will beep twice
and the indicator lamp will glow green.
If the camera is unable to focus, the focus frame
will turn red, s will be displayed, and the
indicator lamp will blink green. Change the
composition or use focus lock (P 34).
Shoot.
4 Smoothly
press the shutter button the rest of the way down to
take the picture.
20
Double
beep
q
Press halfway
Click
w
Press the rest of
the way down
1
If the subject is poorly lit, the AF-assist illuminator may
light to assist focus (P 102). For information on using
the flash when lighting is poor, see page 37.
Taking Pictures
Silent Mode
In situations in which camera sounds or lights may be
unwelcome, hold the DISP/BACK button down until o
is displayed.
Indicator lamp
The indicator lamp shows camera status as follows:
Indicator lamp
Camera status
Glows green Focus locked.
Blur, focus, or exposure warning. PicBlinks green
ture can be taken.
Blinks green Recording pictures. Additional picand orange tures can be taken.
Recording pictures. No additional picGlows
orange
tures can be taken at this time.
Blinks orange Flash charging; flash will not fire when
(Fast)
picture is taken.
Blinks orange The zoom ring is positioned between
(Slow)
ON and OFF. Picture cannot be taken.
Lens or memory error (memory card
Blinks red full or not formatted, format error, or
other memory error).
Basic Photography and Playback
The camera speaker, flash, and AF-assist illuminator/
self-timer lamp turn off and flash and volume settings
can not be adjusted (note that the flash will still fire
when C is selected in scene mode). To restore normal operation, press the DISP/BACK button until the o
icon is no longer displayed.
The Indicator Lamp
2 Warnings
Detailed warnings appear in the display. See pages
116–119 for more information.
21
Viewing Pictures
Pictures can be viewed in the monitor. When taking important photographs, take a test shot and
check the results.
1 Press the a button.
Deleting Pictures
To delete the picture currently displayed
in the monitor, press the selector up (b).
To exit without deleting the picture, highlight CANCEL and press MENU/OK.
The most recent picture will be displayed in
the monitor.
100-0001
1 / 1000
F4.
F4.5
4.5
-1 2 3
additional pictures.
2 View
Press the selector right to view
pictures in the order recorded, left
to view pictures in reverse order.
Press the shutter button to exit to shooting
mode.
22
2 The Playback Menu
Pictures can also be deleted from the playback menu
(P 59).
Shooting Mode
Choose a shooting mode according to the scene or type of subject. To
choose a shooting mode, rotate the mode dial to the desired setting. The
following modes are available:
P, S, A, M: Select for full control over camera settings, including
aperture (M and A) and/or shutter speed (M and S) (P 24).
C1/C2 (CUSTOM): Recall stored settings for
modes P, S, A, M and all EXR modes except R (P 27).
B (AUTO): A simple “point-and-shoot”
mode recommended for first-time users
of digital cameras (P 29).
F (MOVIE): Shoot a movie with sound
(P 65).
Adv. (ADVANCED): Sophisticated techniques made easy (P 29).
More on Photography
EXR: Improve clarity, reduce noise, increase dynamic range, or let the camera
automatically adjust settings to suit the
scene (P 28).
SP (SCENE POSITION): Choose a scene suited to the subject or
shooting conditions and let the camera do the rest (P 33).
23
Shooting Mode
P: PROGRAM AE
In this mode, the camera sets exposure
automatically. If desired, you can choose
different combinations of shutter speed
and aperture that will produce the same
exposure (program shift).
3
If the subject is outside the metering range of the camera, the shutter speed and aperture displays will show
“---”. Press the shutter button halfway to measure exposure again.
Program Shift
Rotate the main/sub-command dial to choose the
desired combination of shutter speed and aperture.
The default values can be restored by raising the
flash or turning the camera off. To use program shift,
turn the flash off and select OFF for g EXTERNAL
FLASH. Furthermore, an option other than AUTO
must be selected for U DYNAMIC RANGE and
N ISO.
Shutter speed
2000
24
F5.6
Aperture
Shooting Mode
S: SHUTTER PRIORITY AE
A: APERTURE PRIORITY AE
Choose the shutter speed using the
main/sub-command dial, while the
camera adjusts aperture for optimal exposure.
Choose the aperture using the main/
sub-command dial, while the camera
adjusts shutter speed for optimal exposure.
Shutter speed
2000
F6.4
3
• If the correct exposure can not be achieved at the
selected shutter speed, aperture will be displayed in
red. Adjust shutter speed until the correct exposure
is achieved. If the subject is outside the metering
range of the camera, the aperture display will show
“F---”. Press the shutter button halfway to measure
exposure again.
• The shutter speed is restricted depending on the ISO
setting.
A
2000
F6.4
3
If the correct exposure can not be achieved at the selected aperture, shutter speed will be displayed in red.
Adjust aperture until the correct exposure is achieved.
If the subject is outside the metering range of the camera, the shutter speed display will show “---”. Press the
shutter button halfway to measure exposure again.
More on Photography
S
Aperture
25
Shooting Mode
M: MANUAL
In this mode, you choose both shutter
speed and aperture. If desired, exposure can be altered from the value suggested by the camera.
Rotate the main-command dial to set the shutter speed or aperture. Press the main-command
dial to change the setting item between shutter
speed and aperture.
Shutter speed
M
2000
F5.6
Sub-command dial
When an option other than
MF is selected for focus mode
(P 46), you can use the subcommand dial to set aperture
or shutter speed.
2000
1
• Rotating the sub-command
dial changes the setting that
is not marked with 8 9.
• Press the main-command
dial to change the setting
item.
F5.6
2000 F5.6
Aperture
1
Rotating the main-command dial changes the setting
marked with 8 9.
3
• Noise in the form of randomly-spaced bright pixels
may occur in long exposures.
• The shutter speed is restricted depending on the ISO
setting.
26
The Exposure Indicator
The amount the picture will
be under- or over-exposed at
current settings is shown by
the exposure indicator.
M
2000
F5.6
Shooting Mode
C1/C2:: CUSTOM MODE
C1/C2
In P, S, A, M and all EXR modes except
R, the K CUSTOM SET option in
the shooting menu (P 87) can be used
to save current camera and menu settings. These settings are recalled whenever the mode dial is rotated to C1/C2
(custom mode).
Menu/setting
c
Once the camera is turned off, R INTELLIGENT DIGITAL ZOOM is deactivated.
More on Photography
Settings saved
N ISO, O IMAGE SIZE, T IMAGE QUALITY, U DYNAMIC RANGE, P FILM SIMULATION, d WB SHIFT, f COLOR, H SHARPShooting NESS, r HIGHLIGHT TONE, s SHADOW
menu
TONE, h NOISE REDUCTION, R INTELLIGENT DIGITAL ZOOM, b FACE DETECTION,
n FACE RECOGNITION, F AF MODE,
I FLASH, g EXTERNAL FLASH
Setup menu C AF ILLUMINATOR, j RAW
Metering (AE), white balance (WB), burst/bracketing mode (DRIVE), macro mode (F), flash
Other
mode (N), program shift, shutter speed, aperture, monitor display options (DISP/BACK)
27
Shooting Mode
EXR ((E
E AUTO/
AUTO/E
E Priority)
Optimize settings for your current subject or improve clarity, reduce noise, or enhance dynamic range. Rotate the mode dial to EXR and choose one of the following E modes
in the shooting menu.
■ R ((E
E AUTO)
The camera automatically selects the scene and E mode according to shooting conditions.
1
If S is selected for O IMAGE SIZE in R mode, the camera will automatically select the optimal image size.
The Scene Icon
The camera selects from the following scenes:
AUTO
LANDSCAPE
NIGHT
a
c
d*
e
u
v
w
x
y
z
Normal
d
dc
dd *
—
du
dv
dw
dx
dy
dz
Backlit
g
gc
—
—
gu
gv
gw
gx
gy
gz
c
cc
cd
ce
cu
cv
cw
cx
cy
cz
Normal
a
ac
ad
—
au
av
aw
ax
ay
az
Backlit
b
bc
—
—
bu
bv
bw
bx
by
bz
Scene
Main subject
Non-portrait
Portrait
Moving object
Portrait and motion
MACRO
BEACH
SUNSET
SNOW
SKY
GREENERY
SKY &
GREENERY
* If n is displayed, the camera will take a series of shots (advanced anti-blur; P 29).
3
The mode selected may vary with shooting conditions. If the mode and subject do not match, select B mode
(P 29) or choose SP (P 33) and select a scene manually.
28
Shooting Mode
Advanced Anti Blur
When n is displayed, the camera will take a series of
exposures and combine them to form a single image,
reducing “noise” (mottling) and blur.
1
n is available when ON is selected in the shooting
menu (P 86) and the flash (P 37) is off or set to
auto.
The EXR Icon
When the shutter button is pressed halfway, the
camera chooses the preferred E mode:
• S (RESOLUTION PRIORITY): Produces crisp, clear
shots.
• T (HIGH ISO & LOW NOISE): Reduces noise in pictures taken at high sensitivities.
■ E Priority
Choose from the following options:
• S (RESOLUTION PRIORITY): Choose for crisp, clear
shots.
• T (HIGH ISO & LOW NOISE): Reduce noise in pictures taken at high sensitivities.
• U (D-RANGE PRIORITY): Increase the amount of
detail visible in highlights.
U DYNAMIC RANGE (P 84) can be set to
M (1600%) and D (800%).
B AUTO
Choose for crisp, clear snapshots. This mode is
recommended in most situations.
More on Photography
3
• Some time may be required to combine the exposures into a single image. A single combined image
may not be created if the subject or camera moves
during shooting. Keep the camera steady during
shooting and do not move the camera until shooting is complete.
• Frame coverage is reduced.
• U (D-RANGE PRIORITY): Increases the amount of
detail visible in highlights.
Adv. ADVANCED
This mode combines “point-and-shoot”
simplicity with sophisticated photographic techniques. The A Adv. MODE option in the shooting menu can be used
to choose from the following advanced
modes:
29
Shooting Mode
■ r MOTION PANORAMA 360
Follow an on-screen guide
to take photos that will
automatically be joined to
form a panorama.
1
2
3
4
5
30
Rotate the zoom ring until the zoom indicator
turns white (P 19).
To select the angle through which you will pan
the camera while shooting, press the selector
down. Press the selector left or right to highlight an angle and press MENU/OK.
Press the selector right to view a choice of pan
directions. Press the selector left or right to
highlight a pan direction and press MENU/OK.
Press the shutter button all the way down to
start recording. There is no need to keep the
shutter button pressed during recording.
Pan the camera in the di120
rection shown by the arrow.
Shooting ends automatically when the progress bar
is full and the panorama is
Progress bar
complete.
1
Shooting ends if the shutter button is pressed all the
way down during shooting. No panorama will be recorded if the shutter button is pressed before the camera has been panned through 120 °.
3
• Do not rotate the zoom ring during shooting.
• Panoramas are created from multiple frames. The
camera may in some cases record a greater or lesser
angle than selected or be unable to stitch the frames
together perfectly. The last part of the panorama
may not be recorded if shooting ends before the
panorama is complete.
• Shooting may be interrupted if the camera is panned
too quickly or too slowly. Panning the camera in a
direction other than that shown cancels shooting.
• The desired results may not be achieved with moving subjects, subjects close to the camera, unvarying
subjects such as the sky or a field of grass, subjects
that are in constant motion, such as waves and waterfalls, or subjects that undergo marked changes in
brightness. Panoramas may be blurred if the subject
is poorly lit.
Shooting Mode
z
Choose z for seamless 360 ° panoramas that can be
played back in a loop (P 64).
1
The t SAVE ORG IMAGE option in the setup menu
can be used to record a v panorama in addition to
a seamless z panorama (P 104).
For Best Results
For best results, move the camera in a small circle at
a steady speed, keeping the camera horizontal and
being careful only to pan in the direction shown by
the guides. If the desired results are not achieved, try
panning at a different speed.
1
Softening can not be applied to background objects
that are too close to the main subject. If a message
stating that the camera can not create the effect is
displayed when the camera focuses, try backing away
from your subject and zooming in. The camera may
also be unable to soften the background if the subject
is moving; if prompted, check the results and try again.
More on Photography
3
Depending on the subject and shooting conditions,
the camera may produce distorted results or a v
panorama. The top and bottom of the area visible in
the shooting display are cropped out and white strips
may appear at the top and bottom of the display.
■ i PRO FOCUS
The camera takes up to three
shots each time the shutter
button is pressed, softening
the background to emphasize
the main subject. The amount
of softening can be adjusted before shooting by
rotating the main/sub-command dial. Use for
portraits or photos of flowers similar to those produced by SLR cameras.
31
Shooting Mode
■ j PRO LOW-LIGHT
Each time the shutter button
is pressed, the camera makes
four exposures and combines
them into a single photograph.
Use to reduce noise and blur
when photographing poorly lit subjects or static
subjects at high zoom ratios.
1
A single combined photograph may not be created
with some scenes or if the subject or camera moves
during shooting. Do not move the camera until shooting is complete.
32
PRO FOCUS/PRO LOW-LIGHT
To save unprocessed copies of pictures taken in these
modes, select ON for the t SAVE ORG IMAGE option in the setup menu (P 104).
3
• Keep the camera steady during shooting.
• Frame coverage is reduced.
Shooting Mode
SP SCENE POSITION
The camera offers a choice of “scenes,” each adapted to particular shooting conditions or
a specific type of subject. Use the A SCENE POSITION option in the shooting menu to
choose the scene assigned to the SP position on the mode dial.
Description
The camera takes two shots: one without the flash and one with.
Capture natural lighting under low-light conditions.
Choose for portraits.
Choose for a smooth skin effect when shooting portraits.
Choose for daylight shots of buildings and landscapes.
Choose when photographing moving subjects.
Choose this mode for poorly lit twilight or night scenes.
Choose this mode for slow shutter speeds when shooting at night.
Slow shutter speeds are used to capture the expanding burst of light from a firework.
Choose this mode to record the vivid colors in sunrises and sunsets.
Choose for crisp, clear shots that capture the brightness of scenes dominated by shining white snow.
Choose for crisp, clear shots that capture the brightness of sunlit beaches.
Reduces the blue cast typically associated with underwater lighting.
Capture indoor background lighting under low-light conditions.
Choose for vivid close-ups of flowers.
Take clear pictures of text or drawings in print.
More on Photography
Scene
C NATURAL & N
D NATURAL LIGHT
L PORTRAIT
Z PORTRAIT ENHANCER
M LANDSCAPE
N SPORT
O NIGHT
H NIGHT (TRIPOD)
U FIREWORKS
Q SUNSET
R SNOW
V BEACH
f UNDERWATER
U PARTY
V FLOWER
W TEXT
33
Focus Lock
To compose photographs with off-center subjects:
1 Position the subject in the focus frame.
Focus.
2 Press
the shutter button
halfway to set focus and
exposure. Focus and exposure will remain locked
while the shutter button
is pressed halfway (AF/AE
lock).
1000
F3.3
1000
F3.3
the picture.
3 Recompose
Keeping the shutter button pressed halfway, recompose the picture.
4 Shoot.
34
Autofocus
Although the camera boasts a high-precision autofocus system, it may be unable to focus on the subjects
listed below. If the camera is unable to focus using
autofocus, use focus lock to focus on another subject
at the same distance and then recompose the photograph.
• Very shiny subjects such as mirrors or car bodies.
• Fast-moving subjects.
• Subjects photographed through a window or other
reflective object.
• Dark subjects and subjects that absorb rather than
reflect light, such as hair or fur.
• Insubstantial subjects, such as smoke or flame.
• Subjects that show little contrast with the background (for example, subjects in clothing that is the
same color as the background).
• Subjects positioned in front of or behind a highcontrast object that is also in the focus frame (for
example, a subject photographed against a backdrop of highly contrasting elements).
The AFL/AEL Button
The AFL/AEL button can be used to lock exposure or focus.
Locking Exposure
Meter exposure.
Position the subject in the
focus frame and press the
AFL/AEL button to meter
exposure.
1
+
ton pressed, press the
shutter button halfway
to focus. Focus and exposure will remain locked while the shutter
button is pressed halfway, even if you later
release the AFL/AEL button.
Repeat steps 1 and 2 as desired to refocus
before taking the picture.
recompose the picture.
c
Adjusting zoom ends AE lock. AE lock is not available with Intelligent Face Detection.
4 Shoot.
Locking Focus
If AF LOCK ONLY is selected for v AE/AF-LOCK
BUTTON in the setup menu (P 102), pressing
the AFL/AEL button locks focus. If AE/AF LOCK is
selected, both focus and exposure will be locked.
a
If AE&AF ON/OFF SWITCH is selected for k AE/
AF-LOCK MODE in the setup menu (P 102), exposure and/or focus will lock when the AFL/AEL button is
pressed and remain locked until the button is pressed
again.
More on Photography
Focus.
2 Keeping
the AFL/AEL but-
the picture.
3 Recompose
Keeping the shutter button pressed halfway,
35
F Macro and Super Macro Modes (Close-ups)
For close-ups, press the selector left (F) to choose from the macro options shown below.
OFF
OFF
Choose from F (macro mode),
G (super macro mode), or
OFF (macro mode off)
When macro mode is in effect, the camera focuses on subjects near the center of the frame. Use the
zoom ring to compose pictures. The following restrictions apply in super macro mode: the lens must
be zoomed all the way out (at other zoom positions, z is displayed) and the flash can not be used.
1
• Use of a tripod is recommended to prevent blur caused by camera shake.
• Flash compensation may be required when using the flash (P 87).
• Using the flash at close range may cast a lens shadow. Zoom a little or have more distance from the subject.
• If macro mode is set while display mode is set to INFO DISPLAY or LCD SWITCHED OFF, display mode automatically turns to STANDARD (P 6).
• Use of the LCD monitor is recommended to avoid parallax at close range.
• The camera can focus at short range when macro mode is not set, but the time needed to focus increases.
• Rotate the zoom ring until the zoom indicator turns white when using G (P 19).
Focus range (distance from front of lens)
• Approx. 50 cm (1.6 ft.)–infinity (wide angle); 80 cm (2.6 ft.)–infinity (telephoto)
• Macro: approx. 10 cm–3 m/0.3 ft.–9.8 ft. (wide angle); 50 cm–5 m/1.6 ft.–16.4 ft. (telephoto)
• Super macro: approx. 1 cm–1 m/0.9 in.–3.2 ft. (wide angle)
36
N Using the Flash (Super-Intelligent Flash)
When the flash is used, the camera’s Super-Intelligent Flash system instantly analyzes the scene based
on such factors as the brightness of the subject, its position in the frame, and its distance from the
camera. Flash output and sensitivity are adjusted to ensure that the main subject is correctly exposed
while preserving the effects of ambient background lighting, even in dimly-lit indoor scenes. Use the
flash when lighting is poor, for example when shooting at night or indoors under low light.
the flash.
1 Raise
Slide the flash pop-up switch to raise the flash.
Mode
A/K
(AUTO FLASH)
N/L
(FORCED FLASH)
O/M
(SLOW SYNCHRO)
Description
More on Photography
a flash mode.
2 Choose
Press the selector right (N). The flash mode changes each time the selector is pressed.
The flash fires when required. Recommended in most situations.
The flash fires whenever a picture is taken. Use for backlit subjects or for natural
coloration when shooting in bright light.
Capture both the main subject and the background under low light (note that
brightly lit scenes may be overexposed).
37
N Using the Flash (Super-Intelligent Flash)
3
The flash may fire several times with each shot. Do not move the camera until shooting is complete.
1
• The peripheral part of an image may be dark when using the flash.
• Remove lens hoods to prevent shadows in photos taken with the flash.
Red-Eye Removal
When Intelligent Face Detection is active (P 52), and ON is selected for B RED EYE REMOVAL in
the setup menu (P 102), red-eye removal is available in K, L, and M.
Red-eye removal minimizes “red-eye” caused when light from the flash is reflected from the subject’s
retinas as shown in the illustration at right.
Turning the Flash Off
Lower the flash where flash photography is prohibited or to capture natural lighting under dim light. At slow shutter speeds, k will be displayed to warn that pictures may be
blurred; use of a tripod is recommended.
38
J Using the Self-Timer
To use the self-timer, press the selector down (h) and choose from the following options:
OFF
OFF
Option
T (OFF)
R (2 SEC)
More on Photography
S (10 SEC)
Description
Self-timer off.
The shutter is released ten seconds after the shutter button is pressed. Use for self-portraits.
The self-timer lamp on the front of the camera lights when the timer starts and begins to
blink shortly before the photo is taken.
The shutter is released two seconds after the shutter button is pressed. Use to reduce blur
caused by the camera moving when the shutter button is pressed. The self-timer lamp will
blink as the timer counts down.
39
Continuous Shooting (Burst Mode/Bracketing)
Capture motion or automatically vary selected settings over a series of pictures.
Press the selector up (DRIVE) and
choose from the following options:
STILL IMAGE
40
B: STILL IMAGE
I: TOP
P: BEST FRAME CAPTURE
O: AE BKT
W: ISO BKT
X: FILM SIMULATION BKT
Y: DYNAMIC RANGE BKT
1
• Focus and exposure are determined by the first frame
in each series. The flash turns off automatically; the
previously-selected flash mode is restored when continuous shooting is turned off.
• Frame rate varies with shutter speed.
• The number of pictures that can be taken in a single
burst varies with the scene and camera settings. The
number of pictures that can be recorded depends on
the memory available.
• Use of the viewfinder is recommended to view the
subject directly with no display lag.
• If P is selected in I or P, pictures will be recorded
at size P or smaller.
• If you select 16 frames in P, pictures will be recorded
at size P or smaller.
Continuous Shooting (Burst Mode/Bracketing)
■ I TOP
The camera takes photographs while the shutter
button is pressed.
1
Press the selector right or left to choose the
frame rate.
Option
Max frame rate
10 fps
7 fps
5 fps
3 fps
The frame rate varies depending on the shooting conditions or numbers of frames in continuous shooting.
Press MENU/OK to return to shooting mode
2 when
settings are complete.
1
When shooting with the self-timer, continuous shooting is not available.
■ P BEST FRAME CAPTURE
The camera takes a series of pictures, starting
before and ending after the shutter button is
pressed. To choose the frame rate and number
of shots:
Highlight the current frame rate and press the
2 selector
right, then press selector up or down
to choose a new value and press MENU/OK to
select.
3
Some frame rates may reduce the number of shots
available in Step 3.
Highlight the number of
3 shots
and press the selec-
Shots per burst
CONTINUOUS SHOOTING SETUP
tor right. Press the selector
16
8 FRAMES
up or down to choose the
number of shots in each
SET
CANCEL
burst and left or right to
choose their distribution Distribution
(the number on the left is taken before and the
number on the right after the shutter button
is pressed). Press MENU/OK when settings are
complete.
–1S
SHUTTER
1S
More on Photography
P
J
K
O
Press the selector right when the camera is in
1 shooting
mode.
41
Continuous Shooting (Burst Mode/Bracketing)
4 Press DISP/BACK to return to shooting mode.
photographs. The camera begins record5 Take
ing while the shutter button is pressed halfway, and completes the burst when the shutter button is pressed all the way down. The
illustration shows a burst of eight shots, three
before the shutter button is pressed and four
after.
Shutter button
Shutter button pressed all the
way down
pressed halfway
“Before”
shots
“After”
shots
3
• If the shutter button is pressed all the way down before the number of frames selected for the “before”
portion is recorded, the remaining frames will be
taken after the shutter button is pressed all the way
down.
• If the shutter button is pressed halfway for an extended period, the camera may record the burst before
the shutter button is pressed all the way down.
42
■ O AE BKT
Press the selector left or right to highlight a
bracketing amount. Each time the shutter button is pressed, the camera will take three shots:
one using the metered value for exposure, the
second overexposed by the selected amount,
and the third underexposed by the same amount
(the camera may not be able to use the selected
bracketing increment if the amount of over- or
under- exposure exceeds the limits of the exposure metering system).
■ W ISO BKT
Press the selector left or right to highlight a bracketing amount. Each time the shutter is released,
the camera will take a picture at the current sensitivity (P 82) and process it to create two additional copies, one with sensitivity raised and the
other with sensitivity lowered by the selected
amount (regardless of the amount selected, sensitivity will not exceed ISO 1600 or fall below ISO
200).
Continuous Shooting (Burst Mode/Bracketing)
■ X FILM SIMULATION BKT
Each time the shutter button is pressed, the
camera takes three shots at different P FILM
SIMULATION settings (P 85): c PROVIA/
STANDARD for the first, d Velvia/VIVID for the
second, and e ASTIA/SOFT for the third.
More on Photography
■ Y DYNAMIC RANGE BKT
Each time the shutter button is pressed, the camera takes three shots at different U DYNAMIC
RANGE settings (P 84): A 100% for the first,
B 200% for the second, and C 400% for
the third (N ISO can not exceed 3200; values less
than 400 are not available when O is selected for
O IMAGE SIZE).
43
d Exposure Compensation
Use exposure compensation when photographing very bright, very dark, or high-contrast subjects.
Rotate the exposure compensation dial.
2000
The effect is visible in the display.
F5.6
Exposure indicator
Choose negative values Choose positive values to
to reduce exposure
increase exposure
44
Metering
To choose how the camera meters exposure, press the AE button and then choose from the following
options.
PHOTOMETRY
MULTI
SPOT
AVERAGE
Description
Automatic scene recognition is used to adjust exposure for a wide range of shooting conditions.
The camera meters lighting conditions at the center of the frame. Recommended when the background is much brighter or darker than the main subject.
Exposure is set to the average for the entire frame. Provides consistent exposure across multiple
q
shots with the same lighting, and is particularly effective for landscapes and portraits of subjects
(AVERAGE)
dressed in black or white.
More on Photography
Option
o
(MULTI)
p
(SPOT)
45
Focus Mode
Use the focus mode selector to choose how the camera focuses.
The following options are available:
Mode
AF-S
(SINGLE AF)
Description
Focus locks while the shutter button is pressed halfway. Choose for stationary subjects.
The camera continually adjusts focus to reflect changes in the distance to the subject even
AF-C
when the shutter button is not pressed halfway (note that this increases the drain on the
(CONTINUOUS AF)
battery). Choose for moving subjects.
Focus manually using the sub-command dial. Rotate the sub-command dial left to reduce
the focus distance, right to increase. The manual focus indicator indicates how closely the
focus distance matches the distance to the subject in the focus brackets (the red bar indicates
the focus distance, the white bar the depth of field, or in other words the distance in front of
and behind the focus point that appears to be in focus). Choose for manual control of focus
or in situations in which the camera is unable to focus using autofocus (P 34). Intelligent
MF
Face Detection turns off automatically.
(MF)
Focus distance
(red bar)
Reduce focus
Increase fodistance
cus distance
Manual focus
M
2000 F6.4
Depth of field
indicator
Manual focus mode icon
(white bar)
46
Focus Mode
2 Manual Focus
• Use of a tripod is recommended. Focus may be affected if the camera moves.
• Use the I FOCUS CONTROL DIAL option in the setup menu (P 103) to reverse the direction of rotation of
the sub-command dial.
• The camera will not focus if the sub-command dial is rotated past infinity.
• To focus using autofocus, press the AFL/AEL button. This can be used to quickly focus on
a chosen subject in manual focus mode.
• The camera can show focus distance in meters or feet. Use the M FOCUS SCALE UNITS
option in the setup menu (P 103) to choose the units used.
M
2000
F6.4
2 Scrolling the focus check area
Press the AF button and then press the selector up, down, left or right to scroll the focus
check area (returned to the center by pressing MENU/OK). The setting takes effect when you
press the AF button again.
M
2000
F6.4
More on Photography
j FOCUS CHECK
If ON is selected for j FOCUS CHECK in the setup menu (P 102),
rotating the sub-command dial magnifies the view in the LCD
monitor.
47
Focus Frame Selection
When t AREA is selected for F AF MODE in
the shooting menu and AF-S is selected for focus
mode, focus position can be changed. Press AF
button and then press the selector up, down, left
or right (the focus frame can be returned to the
center by pressing MENU/OK). The setting takes effect when you press the AF button again.
Focus point
Focus frame
48
When framing a picture in the LCD monitor, you
can choose the size of the focus frame for AF-S.
Press the AF button and then rotate the maincommand dial. The frame size can be reduced up
to 50% or enlarged up to 150% (returned to 100%
by pressing the main-command dial). The setting
takes effect when you press the AF button again.
White Balance
For natural colors, press the WB button and choose a setting that matches the light source.
Option
AUTO
h
k
h: Custom White Balance
Choose h to adjust white balance for unusual lighting conditions. White balance measurement options will
be displayed; frame a white object so that it fills the LCD monitor and press the shutter button all the way down
to measure white balance.
• If “COMPLETED!” is displayed, press MENU/OK to set white balance to the measured value.
• If “UNDER” is displayed, raise exposure compensation (P 44) and try again.
• If “OVER” is displayed, lower exposure compensation and try again.
More on Photography
i
j
k
l
m
n
g
Description
White balance adjusted automatically.
Measure a value for white balance.
Selecting this option displays a list of color temperatures (P 50); highlight a temperature and
press MENU/OK.
For subjects in direct sunlight.
For subjects in the shade.
Use under “daylight” fluorescent lights.
Use under “warm white” fluorescent lights.
Use under “cool white” fluorescent lights.
Use under incandescent lighting.
Reduces the blue cast typically associated with underwater lighting.
1
For greater precision, adjust P FILM SIMULATION, N ISO, and U DYNAMIC RANGE before measuring
white balance.
49
White Balance
1
• White balance is adjusted for flash lighting only in AUTO and g modes. Turn the flash off using other white balance options.
• Results vary with shooting conditions. Play pictures back after shooting to check colors in the LCD monitor.
k: Color Temperature
Color temperature is an objective measure of the color of a light source, expressed in Kelvin (K). Light sources
with a color temperature close to that of direct sunlight appear white; light sources with a lower color temperature have a yellow or red cast, while those with a higher color temperature are tinged with blue. You can match
color temperature to the light source as shown in the following table, or choose options that differ sharply from
the color of the light source to make pictures “warmer” or “colder”.
Choose for redder light sources
or “colder” pictures
2,000 K
Candlelight
Sunset/sunrise
50
Choose for bluer light sources
or “warmer” pictures
15,000 K
Blue sky
5,000 K
Direct sunlight
Shade
The Fn Button
The role played by the Fn button can be selected using the F Fn
BUTTON option in the setup menu (P 101).
The following options are available:
ISO (P 82)/IMAGE SIZE (P 83)/IMAGE QUALITY (P 84)/DYNAMIC RANGE
(P 84)/FILM SIMULATION (P 85)/AF MODE (P 86)/FACE DETECTION (P 86)/
FACE RECOGNITION (P 87)/INTELLIGENT DIGITAL ZOOM (P 86).
More on Photography
51
b Intelligent Face Detection
Intelligent Face Detection allows the camera to automatically detect human faces and set focus and
exposure for a face anywhere in the frame for shots that emphasize portrait subjects. Choose for group
portraits (in horizontal or vertical orientations) to prevent the camera from focusing on the background.
To use Intelligent Face Detection, press MENU/OK to display
the shooting menu and select ON for b FACE DETECTION. Faces can be detected
with the camera in vertical
Green border
or horizontal orientation; if a
face is detected, it will be indicated by a green border. If there is more than one face in the frame, the
camera will select the face closest to the center;
other faces are indicated by white borders.
3
• In some modes, the camera may set exposure for the
frame as a whole rather than the portrait subject.
• If the subject moves as the shutter button is pressed,
their face may not be in the area indicated by the
green border when the picture is taken.
52
Intelligent Face Detection
Intelligent Face Detection is
recommended when using
the self-timer for group- or
self-portraits (P 39).
7
When a picture taken with Intelligent Face Detection
is displayed, the camera can automatically select faces
for red-eye removal (P 92), playback zoom (P 57),
slide shows (P 90), image search (P 61), image disp.
(P 99), printing (P 74), and cropping (P 93).
n Face Recognition
The camera can store information on the face
and personal details (name, relationship, and
birth date) of portrait subjects and assign these
subjects priority for Intelligent Face Detection or
display their names and other information during
playback.
Adding New Faces
Select REGISTER.
1 Select
REGISTER for n FACE RECOGNITION in the shooting menu.
1
To disable face recognition, select OFF.
a photograph.
2 Take
After checking that
the
subject is facing the camera, frame the subject using the guides and take
the photograph.
REGISTER FACE
CAPTURE THE FACE
ALONG WITH THE GUIDLINE
face recognition data.
3 Enter
Press MENU/OK to display face recognition
data and enter the following information:
• NAME: Enter a name of up to 14 characters
and press MENU/OK.
• BIRTHDAY: Enter the subject’s date of birth
and press MENU/OK.
• CATEGORY: Choose the option that describes
your relationship to the subject and press
MENU/OK.
1
If you attempt to zoom in on the face of a person indicated by a green border in the face recognition database on their birthday, the camera will display their
name and the message “Happy Birthday!”.
More on Photography
Follow the steps below to add faces to the face
recognition database.
1
If an error is displayed, take the photograph again.
c
Face recognition may not be available depending on
the shooting mode.
CANCEL
53
n Face Recognition
Viewing, Editing, and Deleting Existing Data
Follow the steps below to view, edit, or delete
face recognition data.
Select VIEW & EDIT for n FACE RECOG1 NITION.
2
or edit face recognition data.
3 View
The name, category, or birth date can be edSelect a face.
ited as described in Step 3 of “Adding New
Faces” (P 53). To retake the photo, select
REPLACING IMAGE and shoot a new portrait as described above.
1
To delete face recognition data for the selected subject, select ERASE.
54
Face Recognition
The camera can store up to eight faces. If you attempt
to add a ninth face, a confirmation dialog will be displayed; use VIEW & EDIT to make room for new faces
by deleting existing data.
When Intelligent Face Detection (P 52) is on and
the frame contains multiple subjects from the face
recognition database, the camera displays the name
of the subject that will be used to set focus and exposure (the subject shown by the green frame). If no
name is entered, the camera will show “---”. Subjects
identified using face recognition but not used to set
focus and exposure are shown by orange frames,
other subjects by white frames.
3
The camera may fail to identify subjects in the face
recognition database if they are not facing the camera or are only partly in the frame, or if details of the
subjects’ faces or expressions differ markedly from
those in the database.
Taking RAW pictures
The camera can take RAW pictures. RAW pictures
are unprocessed data read from the image sensor.
To take RAW pictures, select j RAW in the setup
menu (P 102).
Choose RAW+JPEG or RAW to record RAW pictures. If RAW+JPEG is selected, JPEG copies will
also be recorded. Choose OFF to record pictures
in JPEG format only.
3
• RAW pictures cannot be recorded to internal memory. Insert a memory card.
• Crop, resize, and red-eye removal options are not
available with RAW images during playback. The
maximum zoom available when viewing RAW images is 3.2×.
j options
RAW+JPEG
RAW
OFF
RAW button pressed
JPEG
JPEG
RAW+JPEG
Taking a picture or pressing the RAW button again restores the previous setting.
Creating JPEG Copies of RAW Pictures
Pressing the RAW button during playback displays
RAW conversion options (P 91).
More on Photography
1
• To convert RAW files for display on the camera,
use j RAW CONVERSION in the playback menu
(P 91).
• To convert RAW files for display on a computer, use
the supplied RAW File Converter software.
RAW button
Press the RAW button to temporarily change the recording format.
55
Playback Options
To view the most recent picture in the monitor,
press the a button.
100-0001
1 / 1000
F4.
F4.5
4.5
More on Playback
Press the selector right to view pictures
in the order recorded, left to view pictures in reverse order. Keep the selector
pressed to scroll rapidly to the desired
frame.
-1 2 3
Continuous Shooting
In the case of pictures taken in continuous shooting mode, only the first frame of each series will
be displayed. Press the selector down to view the
other pictures in the series.
I Favorites: Rating Pictures
To rate the picture currently displayed in full-frame
playback, press DISP/BACK and press the selector
up and down to select from zero to five stars.
1
Pictures taken using other cameras are indicated by a m (“gift image”) icon during playback.
56
Playback Options
Playback Zoom
Press k to zoom in on pictures displayed in single-frame playback; n to zoom out. When the
picture is zoomed in, the selector can be used to
view areas of the image not currently visible in the
display.
Intelligent Face Detection
Pictures taken with Intelligent Face Detection (P 52)
are indicated by a g icon. Press the f button to
zoom in on the subject selected with Intelligent Face
Detection. You can then use the k and n buttons
to zoom in and out.
Zoom indicator
Navigation window
shows portion of image
currently displayed in
monitor
1
The maximum zoom ratio varies with image size. Playback zoom is not available with cropped or resized
copies saved at a size of a or smaller.
More on Playback
Press DISP/BACK or MENU/OK to exit zoom.
57
Playback Options
Multi-Frame Playback
To change the number of images displayed, press
n in single-frame view.
100-0001
Use the selector to highlight images and press
MENU/OK to view the highlighted image full frame.
In the nine- and hundred-frame displays, press
the selector up or down to view more pictures.
2 Two-Frame Display
Two-frame display can be used
to compare pictures taken in
C mode.
Press k to view
fewer images.
Press n to view
more images.
58
A Deleting Pictures
To delete individual pictures, multiple selected pictures, or all pictures,
press MENU/OK, select A ERASE (P 89), and choose from the options
below. Note that deleted pictures can not be recovered. Copy important
pictures to a computer or other storage device before proceeding.
Option
FRAME
SELECT FRAMES
BACK
FRAME
SELECTED FRAMES
ALL FRAMES
SET
Description
Press the selector left or right to scroll through pictures and press MENU/OK to delete the current
picture (a confirmation dialog is not displayed).
Highlight pictures and press MENU/OK to select or deselect (pictures included in the photobook
or print order are shown by S). When the operation is complete, press DISP/BACK to display a
confirmation dialog, then highlight OK and press MENU/OK to delete the selected pictures.
A confirmation dialog will be displayed; highlight OK and press MENU/OK to delete all unprotected pictures (if a memory card is inserted, only the pictures on the memory card will be affected; the pictures in internal memory are only deleted if no memory card is inserted). Pressing
DISP/BACK cancels deletion; note that any pictures deleted before the button was pressed can
not be recovered.
1
• Protected pictures can not be deleted. Remove protection from any pictures you wish to delete (P 92).
• If a message appears stating that the selected images are part of a DPOF print order, press MENU/OK to delete the
pictures.
More on Playback
ALL FRAMES
PLAYBACK MENU
ERASE
59
Viewing Photo Information
Photo information can be viewed by pressing DISP/BACK to cycle through indicators (P 7) until the following display appears:
Additional photo information
Additional photo information
can be viewed by rotating the
main-command dial. Rotate the
main-command dial to cycle the
display.
4:3 N
ISO 400
F4.5
1/250
:
: OFF
:
: -1 2 3
12/31/2050 10 : 00 AM
100-0001
q Dynamic range w Image size and quality
e Sensitivity
r Shutter speed/aperture
t Film simulation y Flash mode u White balance
i Exposure compensation o Frame number
!0 Picture (overexposed areas blink on and off )
!1 Histogram
60
D-RANGE
COLOR
HIGHLIGHTTONE
SHADOWTONE
SHARPNESS
FILM SIM.
WHITE BALANCE
: AUTO
: STD
: STD
: STD
: --: Velvia
: AUTO
a
The active focus point is shown by a “+” icon.
Zooming in on the Focus Point
Press the main-command dial
to zoom in on the focus point.
Press the main-command dial
again to return to full-frame
playback.
Image Search
Search for images by various criteria.
b IMAGE SEARCH in the playback 2 Select a search condition. Only pictures that
1 Select
match the search condition will be displayed.
menu (P 89), highlight one of the following
search criteria, and press MENU/OK:
Option
To delete or protect selected pictures or to
view the selected pictures in a slide show,
press MENU/OK and choose from the following
options:
Option
A ERASE
D PROTECT
I SLIDE SHOW
See page
59
92
90
More on Playback
Description
Find all pictures taken on a selected
BY DATE
date.
Find all pictures based on specified face
BY FACE
information.
Find all pictures with a specified rating
BY I FAVORITES
(P 56).
Find all pictures that match a selected
BY SCENE
scene.
Find all still pictures, all movies, all picBY TYPE OF DATA tures taken in burst mode, or all RAW
pictures.
Find all pictures selected for upload to a
BY UPLOAD MARK
specified destination (P 89).
61
X PhotoBook Assist
Create books from your favorite photos.
Creating a PhotoBook
Select X PHOTOBOOK ASSIST in the play- 5 Scroll through the images and press the selec1 back
tor up to select or deselect the current image
menu.
2 Highlight NEW BOOK.
for inclusion in the book. To display the current
image on the cover, press the selector down.
Press MENU/OK to display the new
3 book
dialog.
1
The first picture selected automatically becomes
the cover image. Press the selector down to select
a different picture for the cover.
pictures for the new book.
4 Choose
• SELECT FROM ALL: Choose from all the
pictures available.
• SELECT BY IMAGE SEARCH: Choose from pictures
matching selected search conditions (P 61).
1
Neither photographs a or smaller nor movies can
be selected for photobooks.
MENU/OK to exit when the book
6 isPress
complete.
7 Highlight COMPLETE PHOTOBOOK.
SELECT IMAGES FOR PHOTOBOOK
SELECT ALL
COMPLETE PHOTOBOOK
EXIT
1
Choose SELECT ALL to select all photos, or all photos matching the specified search conditions, for
the book.
62
k PhotoBook Assist
Press MENU/OK. The new book will be
8 added
to the list in the photobook
assist menu.
3
• Photobooks can contain up to 300 pictures.
• Books that contain no photos are automatically
deleted.
PhotoBooks
Photobooks can be copied to a computer using the
supplied MyFinePix Studio software.
Viewing PhotoBooks
Highlight a book in the photobook assist menu
and press MENU/OK to display the book, then press
the selector left and right to scroll through the
pictures. Press DISP/BACK to return to the photobook assist menu.
Editing and Deleting PhotoBooks
the photobook and press
1 Display
MENU/OK to view book edit options.
PhotoBook” on page 62.
• ERASE: Delete the current photobook.
3 Follow the on-screen instructions.
More on Playback
from the following options:
2 Choose
• EDIT: Edit the book as described in “Creating a
63
Viewing Panoramas
If you press the selector down when a panorama is displayed full frame, the camera will play back the
picture from left to right or from bottom to top.
PLAY
STOP
PAUSE
The following operations can be performed during playback:
Operation
Start/pause
playback
End playback
Button
Description
Press the selector down to start playback. Press again to pause.
Press the selector up to end playback.
1
• Once displayed in full-frame playback, panoramas can be zoomed in or out using the zoom buttons.
• z panoramas play back in an endless loop (P 31); the playback direction can be controlled by pressing the
selector left or right. The camera will not turn off automatically while playback is in progress (P 101).
64
Recording Movies
Shoot short movies with sound. During recording, R and the time remaining will be displayed in
the LCD monitor and sound will be recorded via the built-in microphone (be careful not to cover the
microphone during recording).
98
18m39s
Number of photos that
can be taken during
recording
Time remaining
1 Rotate the mode dial to F MOVIE.
2 Press the shutter button all the way down to start recording.
end recording, press the shutter button again. Recording ends automatically when the
3 To
movie reaches maximum length or memory is full.
Movies
1
• Zoom can be adjusted while recording is in progress.
• If the subject is poorly lit, the AF-assist lamp may light to assist the focus operation.
To turn the AF-assist lamp off , select OFF for C AF ILLUMINATOR in the setup menu (P 102).
• Focus, exposure, and white balance are adjusted automatically throughout recording. The color and brightness
of the image may vary from that displayed before recording begins.
• Sounds made by the camera may be recorded.
65
Recording Movies
Taking Photographs During Recording
Press MENU/OK to take a photograph during recording.
1
• If O is selected for O IMAGE SIZE, the picture
will be recorded at size P.
• The photo is saved separately from the movie and
does not appear as part of the movie.
3
• Photos can not be taken while a high-speed movie
is being recorded.
• The number of photos that can be taken is limited.
3
• The indicator lamp lights while movies are being recorded. Do not open the battery chamber during
shooting or while the indicator lamp is lit. Failure
to observe this precaution could prevent the movie
from being played back.
• Vertical or horizontal streaks may appear in movies
containing very bright subjects. This is normal and
does not indicate a malfunction.
• The temperature of the camera may rise if it is used to
record movies for an extended period or if the ambient temperature is high. This is normal and does not
indicate a malfunction.
66
Movie Frame Size
Before recording, select a frame size using the
W MOVIE MODE option in the shooting menu
(P 88).
Option
Description
i 1920 (1920 × 1080) Full HD (High Definition).
h 1280 (1280 × 720) High Definition.
Standard definition.
f (640 × 480)
High speed movie. Sound is not
Y 640 × 480 (70fps)
recorded, and focus, exposure, and
white balance are not adjusted auY 320 × 240 (120fps)
tomatically. Black bands appear at
the top and bottom of movies reY 320 × 112 (200fps)
corded at Y 320 × 112.
a Viewing Movies
During playback (P 56),
movies are displayed in the
monitor as shown at right.
The following operations
can be performed while a
movie is displayed:
Operation
100-006
PLAY
STOP
5m42s
PAUSE
2 Viewing Movies on a Computer
Copy movies to the computer before viewing.
3
Do not cover the speaker during playback.
Movies
Description
Press the selector down to start playback.
Start/ Press again to pause. While playback is
pause paused, you can press the selector left or
playback right to rewind or advance one frame at
a time.
End
playback/ Press the selector up to end playback.
delete
Adjust Press the selector left or right to adjust playspeed back speed during playback.
Press MENU/OK to pause playback and display volume controls. Press the selector
Adjust
up or down to adjust the volume and
volume
press MENU/OK to exit. Volume can also be
adjusted from the setup menu.
Playback Speed
Arrow
Press the selector left or right to
adjust playback speed. Speed is
shown by the number of arrows
(M or N).
67
Viewing Pictures on TV
Connect the camera to a TV to show pictures to a group.
1 Turn the camera off.
2 Connect the A/V cable (optional) or HDMI cable (available from third-party suppliers).
Insert into USB
connector
Connect white plug
to audio-in jack
Connect yellow plug
to video-in jack
Insert into HDMI
connector
Insert into HDMI
connector
Connections
68
HDMI Mini Connector
Viewing Pictures on TV
HDMI
An HDMI cable (available from third-party suppliers; P 106) can be used to connect the camera to High
Definition (HD) devices (playback only). The USB cable or optional A/V cable cannot be used while an HDMI
cable is connected.
the television to the video or HDMI input channel. See the documentation supplied with the
3 Tune
television for details.
Press the a button for about a second to turn the camera on. The camera monitor turns off and
4 pictures
and movies are played back on the TV. Note that the camera volume controls have no effect on sounds played on the TV; use the television volume controls to adjust the volume.
1
Image quality drops during movie playback.
3
When connecting the cable, be sure the connectors are fully inserted.
Connections
69
Printing Pictures via USB
If the printer supports PictBridge, the camera can be connected directly to the printer and
pictures can be printed without first being copied to a computer. Note that depending on
the printer, not all the functions described below may be supported.
Connecting the Camera
Printing Selected Pictures
Connect the supplied USB cable as shown and 1 Press the selector left or right to display a pic1 turn
the printer on.
ture you wish to print.
the selector up or down to choose the
2 Press
number of copies (up to 99).
steps 1–2 to select additional pictures.
3 Repeat
Press MENU/OK to display a confirmation dialog
Press the a button for about a second to turn
2 the
camera on. t USB will be displayed in
when settings are complete.
PRINT THESE FRAMES
TOTAL: 9 SHEETS
the monitor, followed by the PictBridge display
shown below at right.
USB
YES
PICTBRIDGE
TOTAL: 00000
4 Press MENU/OK to start printing.
00 SHEETS
FRAME
OK
70
CANCEL
SET
Printing Pictures via USB
2 Printing the Date of Recording
To print the date of recording on pictures, press DISP/
BACK in steps 1–2 to display the PictBridge menu (see
“Printing the DPOF Print Order,” below). Press the selector up or down to highlight PRINT WITH DATE s
and press MENU/OK to return to the PictBridge display
(to print pictures without the date of recording, select
PRINT WITHOUT DATE).
1
If no pictures are selected when the MENU/OK button is
pressed, the camera will print one copy of the current
picture.
Printing the DPOF Print Order
To print the print order created with K PRINT
ORDER (DPOF) in the playback menu (P 95):
display, press DISP/BACK to
1 InopenthethePictBridge
PictBridge menu.
PICTBRIDGE
PRINT WITH DATE
PRINT WITHOUT DATE
PRINT DPOF
the selector up or down to highlight
2 Press
u PRINT DPOF.
3 Press MENU/OK to display a confirmation dialog.
YES
CANCEL
Connections
PRINT DPOF OK?
TOTAL: 9 SHEETS
71
Printing Pictures via USB
4 Press MENU/OK to start printing.
During Printing
The message shown at right
is displayed during printing.
Press DISP/BACK to cancel before all pictures are printed
(depending on the printer,
printing may end before the
current picture has printed).
PRINTING
CANCEL
If printing is interrupted, turn the camera off and then
on again.
Disconnecting the Camera
Confirm that “PRINTING” is not displayed in the monitor and turn the camera off. Disconnect the USB
cable.
72
1
• Pictures can be printed from internal memory or a
memory card that has been formatted in the camera.
• If the printer does not support date printing, the
PRINT WITH DATE s option will not be available in
the PictBridge menu and the date will not be printed
on the pictures in the DPOF print order.
• When pictures are printed via direct USB connection,
page size, print quality, and border selections are
made using the printer.
Printing Pictures via USB
Creating a DPOF Print Order
The K PRINT ORDER (DPOF) option in the playback menu can be used to create a digital “print
order” for PictBridge-compatible printers (P 106)
or devices that support DPOF.
DPOF
DPOF (Digital Print Order Format) is a standard that allows pictures to be printed from
“print orders” stored in internal memory or
on a memory card. The information in the
order includes the pictures to be printed, date imprint, and the number of copies of each picture.
■ WITH DATE s// WITHOUT DATE
Select playback mode and press MENU/OK to
display the playback menu.
1
Highlight K PRINT ORDER (DPOF) and press
2 MENU/OK.
one of the following options and
3 Highlight
press MENU/OK:
• WITH DATE s: Print the date of recording on
pictures.
• WITHOUT DATE: Do not print the date of recording on pictures.
Press the selector left or right to display a pic4 ture
you wish to include in or remove from the
Connections
print order.
73
Printing Pictures via USB
the selector up or down to choose the 6 Repeat steps 4–5 to complete the print order.
5 Press
number of copies (up to 99). To remove a picPress MENU/OK to save the print order when setture from the order, press the selector down
until the number of copies is 0.
PRINT ORDER (DPOF)
DPOF: 00001
Total number of prints
Number of copies
01 SHEETS
FRAME
SET
2 Intelligent Face Detection
If the current picture was created with Intelligent
Face Detection, pressing f sets the number of copies to the number of faces detected.
1
When pictures are printed via direct USB connection, page size, print quality, and border selections
are made using the printer.
74
tings are complete, or DISP/BACK to exit without
changing the print order.
The total number of prints is displayed in the
7 monitor.
Press MENU/OK to exit.
The pictures in the current
print order are indicated by a
u icon during playback.
Printing Pictures via USB
1
• Remove the memory card to create or modify a print
order for the pictures in internal memory.
• Print orders can contain a maximum of 999 pictures.
RESET DPOF OK?
• If a memory card is inserted
containing a print order created by another camera, the
message shown at right will
YES
NO
be displayed. Pressing MENU/
OK cancels the print order; a
new print order must be created as described above.
■ RESET ALL
RESET DPOF OK?
To cancel the current print
order, select RESET ALL
in the K PRINT ORDER
(DPOF) menu. The confirYES
CANCEL
mation shown at right will
be displayed; press MENU/OK to remove all pictures
from the order.
Connections
75
Viewing Pictures on a Computer
The supplied software can be used to copy pictures to a computer, where they can be stored, viewed,
organized, and printed. Before proceeding, install the software as described below. Do NOT connect the
camera to the computer until installation is complete.
Installing the Software
Two applications are supplied: MyFinePix Studio for Windows and FinePixViewer for the Macintosh.
Installation instructions for Windows are on pages 76–77, those for the Macintosh on pages 78–79.
Windows: Installing MyFinePix Studio
Confirm that the computer meets the following system requirements:
1
CPU
RAM
Free disk space
GPU
Video
Other
Windows 7 (SP 1)/Windows Vista (SP 2) 1
3 GHz Pentium 4 or better
(2.4 GHz Core 2 Duo or better) 2
1 GB or more
Windows XP (SP 3) 1
2 GHz Pentium 4 or better
(2.4 GHz Core 2 Duo or better) 2
512 MB or more
(1 GB or more) 2
2 GB or more
Supports DirectX 9 or later
Supports DirectX 7 or later
(recommended)
(required; performance not guaranteed with other GPUs)
1,024 × 768 pixels or more with 24-bit color or better
• Built-in USB port recommended. Operation is not guaranteed with other USB ports.
• Internet connection (broadband recommended) required to install .NET Framework (if necessary), to use
auto update feature, and when performing such tasks as sharing pictures on-line or via e-mail.
1 Other versions of Windows are not supported. Only pre-installed operating systems are supported; operation is not
guaranteed on home-built computers or computers that have been upgraded from earlier versions of Windows.
2 Recommended when displaying HD movies.
76
Viewing Pictures on a Computer
2 Start the computer. Log in to an account with administrator privileges before proceeding.
3 Exit any applications that may be running and insert the installer CD in a CD-ROM drive.
Windows 7/Windows Vista
If an AutoPlay dialog is displayed, click SETUP.EXE. A “User Account Control” dialog will then be displayed;
click Yes (Windows 7) or Allow (Windows Vista).
The installer will start automatically; click Install MyFinePix Studio and follow the on-screen instructions to install MyFinePix Studio.
If the Installer Does Not Start Automatically
If the installer does not start automatically, select Computer or My Computer from the Start menu, then
double-click the FINEPIX CD icon to open the FINEPIX CD window and double-click setup or SETUP.EXE.
If prompted to install Windows Media Player, DirectX, or .NET Framework, follow the on-screen in4 structions
to complete installation.
number is printed at the top of the CD label for reference when updating the software or contacting
customer support.
Installation is now complete. Proceed to “Connecting the Camera” on page 80.
Connections
Remove the installer CD from the CD-ROM drive when installation is complete. Store the installer
5 CD
in a dry location out of direct sunlight in case you need to re-install the software. The version
77
Viewing Pictures on a Computer
Macintosh: Installing FinePixViewer
Confirm that the computer meets the following system requirements:
1
CPU
PowerPC or Intel (Core 2 Duo or better) *
Pre-installed versions of Mac OS X version 10.3.9–10.6
OS
(visit http://www.fujifilm.com/support/digital_cameras/compatibility/ for more information)
RAM
256 MB or more (1 GB or more) *
Free disk space A minimum of 200 MB required for installation with 400 MB available when FinePixViewer is running
Video
800 × 600 pixels or more with thousands of colors or better
Other
Built-in USB port recommended. Operation is not guaranteed with other USB ports.
* Recommended when displaying HD movies.
After starting the computer and quitting any applications that may be running, insert the installer
2 CD
in a CD-ROM drive and double-click Installer for Mac OS X.
1
To install RAW FILE CONVERTER, double-click SILKYRFCEXInstaller. RAW FILE CONVERTER is used to view
RAW images on your computer.
installer dialog will be displayed; click Installing FinePixViewer to start installation. Enter an
3 An
administrator name and password when prompted and click OK, then follow the on-screen instructions to install FinePixViewer. Click Exit to quit the installer when installation is complete.
78
Viewing Pictures on a Computer
the installer CD from the CD-ROM drive. Note that you may be unable to remove the CD
4 Remove
if Safari is running; if necessary, quit Safari before removing the CD. Store the installer CD in a dry
location out of direct sunlight in case you need to re-install the software. The version number is
printed at the top of the CD label for reference when updating the software or contacting customer
support.
Mac OS X 10.5 or earlier: Open the “Applications” folder, start Image Capture, and select Preferences…
5 from
the Image Capture application menu. The Image Capture preferences dialog will be displayed;
choose Other… in the When a camera is connected, open menu, then select FPVBridge in the
“Applications/FinePixViewer” folder and click Open. Quit Image Capture.
Mac OS X 10.6: Connect the camera and turn it on. Open the “Applications” folder and start Image
Capture. The camera will be listed under DEVICES; select the camera and choose FPVBridge from
the Connecting this camera opens menu and click Choose. Quit Image Capture.
Installation is now complete. Proceed to “Connecting the Camera” on page 80.
Connections
79
Viewing Pictures on a Computer
Connecting the Camera
If the pictures you wish to copy are stored on a 3 Press the a button for about a second to
1 memory
card, insert the card into the camera
turn the camera on. MyFinePix Studio or
(P 11).
1
Windows users may require the Windows CD when
starting the software for the first time.
3
Loss of power during transfer could result in loss of
data or damage to internal memory or the memory
card. Charge the battery before connecting the
camera.
2
80
Turn the camera off and connect the supplied
USB cable as shown, making sure the connectors are fully inserted. Connect the camera directly to the computer; do not use a USB hub
or keyboard.
FinePixViewer will start automatically; follow
the on-screen instructions to copy pictures to
the computer. To exit without copying pictures, click Cancel.
3
If the software does not start automatically, it may
not be correctly installed. Disconnect the camera
and reinstall the software.
For more information on using the supplied software, start the application and select the appropriate option from the Help menu.
Viewing Pictures on a Computer
3
Disconnecting the Camera
After confirming that the indicator lamp is out, follow
the on-screen instructions to turn the camera off and
disconnect the USB cable.
Uninstalling the Supplied Software
Only uninstall the supplied software when it is no longer required or before beginning reinstallation. After
quitting the software and disconnecting the camera,
drag the “FinePixViewer” folder from “Applications”
into the Trash and select Empty Trash in the Finder
menu (Macintosh), or open the control panel and use
“Programs and Features” (Windows 7/Windows Vista)
or “Add or Remove Programs” (Windows XP) to uninstall MyFinePix Studio. Under Windows, one or more
confirmation dialogs may be displayed; read the contents carefully before clicking OK.
Connections
• If a memory card containing a large number of images
is inserted, there may be a delay before the software
starts and you may be unable to import or save images. Use a memory card reader to transfer pictures.
• Make sure that the computer does not display a message stating that copying is in progress and that the
indicator lamp is out before turning the camera off or
disconnecting the USB cable (if the number of images copied is very large, the indicator lamp may remain
lit after the message has cleared from the computer
display). Failure to observe this precaution could result in loss of data or damage to internal memory or
the memory card.
• Disconnect the camera before inserting or removing
memory cards.
• In some cases, it may not be possible to access pictures
saved to a network server using the supplied software
in the same way as on a standalone computer.
• The user bears all applicable fees charged by the
phone company or Internet service provider when
using services that require an Internet connection.
81
Using the Menus: Shooting Mode
Use the shooting menus to adjust shooting settings. The options available vary with the shooting mode selected.
Using the Shooting Menu
Press MENU/OK to display the shoot1 ing
menu.
Press the selector up or down to
2 highlight
the desired menu item.
Press the selector right to display op3 tions
for the highlighted item.
Press the selector up or down to
4 highlight
the desired option.
Menus
82
Press MENU/OK to select the high5 lighted
option.
Press DISP/BACK
6 menu.
to exit from the
Shooting Menu Options
Default values are shown in square brackets [ ].
A E MODE
[R]
[R
Choose an option for E mode (P 28).
A Adv. MODE
[r]
[r
Choose an advanced shooting mode (P 29).
A SCENE POSITION
Choose a scene for SP mode (P 33).
[L
[L]
N ISO
[AUTO (800)]
Control the camera’s sensitivity to light.
Option
Description
Sensitivity is adjusted autoAUTO
matically in response to shooting conditions.
As above, except that sensitivAUTO (3200) / AUTO (1600) /
ity will not be raised above the
AUTO (800) / AUTO (400)
value in parentheses.
12800 / 6400 / 5000 /
4000 / 3200 / 2500 /
Sensitivity is set to the speci2000 / 1600 / 1250 /
fied value, which is shown in
1000 / 800 / 640 / 500 /
the display.
400 / 320 / 250 / 200 / 100
Using the Menus: Shooting Mode
ISO
Higher values can reduce blur; note, however, that
mottling may appear in pictures taken at high sensitivities.
100
Bright
Less
noticeable
ISO
Scene
Noise
(mottling)
12800
Dark
More
noticeable
O IMAGE SIZE
[O 4 : 3]
[O
3]
O 4:3
Choose the image size and
aspect ratio at which pictures
are recorded. Large pictures Size Aspect ratio
can be printed at large sizes with no drop in quality, while small pictures require less memory, allowing more pictures to be recorded.
Size Versus Aspect Ratio
Size
Option
Prints at sizes up to
O 34 × 25 cm (13.5 × 10 in.)
P 24 × 18 cm (9.5 × 7 in.)
Q 17 × 13 cm (7 × 5 in.)
Aspect ratio
4 : 3: Pictures have the same proportions as the camera
display.
3 : 2: Pictures have the same proportions as a frame of
35 mm film.
16 : 9: Suited for display on High Definition (HD) devices.
1 : 1: Pictures are square.
Menus
83
Using the Menus: Shooting Mode
T IMAGE QUALITY
[FINE]
Choose how much image files are compressed.
Option
FINE
NORMAL
Description
Low compression. Select for higher image
quality.
High compression. Select this option to
store more pictures.
U DYNAMIC RANGE
[AUTO]
Control contrast. Higher values are recommended for scenes that include both sunlight and deep
shade or for increased contrast with such subjects
as sunlight on water, brightly-lit autumn leaves,
portraits taken against a blue sky, and white objects or people wearing white; note, however, that
mottling may appear in pictures taken at higher
values. If AUTO is selected, the camera will automatically select values between 100% and 400%
in response to shooting conditions.
84
Option
AUTO
Description
A 100% Increase contrast when shooting
indoors or under overcast skies.
B 200%
C 400%
D 800%
M 1600%
Reduce loss of detail in highlights
and shadows when photographing high-contrast scenes.
1
M 1600% and D 800% are available only when
D-RANGE PRIORITY is selected in E mode.
Using the Menus: Shooting Mode
P FILM SIMULATION
[c
[c]
Simulate the effects of different types of film, including sepia and black-and-white.
Option
f COLOR
Adjust color density.
[MID]
H SHARPNESS
[STD]
Choose whether to sharpen or soften outlines.
r HIGHLIGHT TONE
Adjust the appearance of highlights.
[STD]
s SHADOW TONE
Adjust the appearance of shadows.
[STD]
h NOISE REDUCTION
Choose the amount of noise reduction.
[STD]
Menus
Description
Standard color reproduction. Suited to a
c (PROVIA/
wide range of subjects, from portraits to
STANDARD)
landscapes.
d (Velvia/ A high-contrast palette of saturated colors, suited to nature photographs.
VIVID)
e (ASTIA/ A soft-toned palette of less saturated colors.
SOFT)
b (MONOTake pictures in black and white.
CHROME)
Take black-and-white pictures with
e (MONOslightly increased contrast. This setting
CHROME +
also slightly tones down the brightness
Ye FILTER)
of the sky.
d (MONO- Take black-and-white pictures with increased contrast. This setting also tones
CHROME +
down the brightness of the sky.
R FILTER)
f (MONOSoften skin tones in black-and-white porCHROME +
traits.
G FILTER)
f (SEPIA) Take pictures in sepia.
d WB SHIFT
White balance can be fine-tuned. Adjust the selected color axis (R–Cy=Red-Cyan or B-Ye=Blue–
Yellow) by +3 to –3 in increments of one.
85
Using the Menus: Shooting Mode
R INTELLIGENT DIGITAL ZOOM
[OFF]
If ON is selected, intelligent digital zoom magnifies the image to 2× while processing it for sharp,
high-resolution results.
a
• Intelligent digital zoom may end when another mode
is selected.
• Intelligent digital zoom may sometimes produce lower quality images than optical zoom.
• The time needed to record images increases.
• The effects are not visible in the display during shooting.
• Intelligent digital zoom is not available in continuous
mode or during movie recording.
Z ADVANCED ANTI BLUR
[ON]
Select ON to enable advanced anti blur in R
mode (P 29).
b FACE DETECTION
Choose whether the camera automatically detects and sets focus and exposure for human portrait subjects (P 52).
86
F AF MODE
[t]
[t
Choose how the camera selects the focus area
when in AF-S focus mode (P 46). Note that regardless of the option selected, the camera will
focus on the subject in the center of the monitor
when macro mode is on (P 36).
• s MULTI: When the shutter button is pressed
halfway, the camera detects high-contrast subjects near the center of the frame and selects
the focus area automatically.
• t AREA: Choose the focus area manually
(P 48).
• x TRACKING: Position the subject in the focus target and press the selector left. The camera will track the subject and adjust focus as it
moves through the frame.
1
Note that in x mode, the camera focuses continuously, increasing the drain on the battery, and that the
sound of the camera focusing may be audible.
Using the Menus: Shooting Mode
n FACE RECOGNITION
Add portrait subjects to the face recognition database. These subjects will be given priority during Intelligent Face Detection, and their names
and other information can be viewed during playback (P 53).
I FLASH
[±0]
Adjust flash brightness. Choose from values between +2/3 EV and –2/3 EV. The default setting is ±0.
Note that the desired results may not be achieved
depending on shooting conditions and the distance to the subject.
g EXTERNAL FLASH
[OFF]
Choose ON when using an optional flash unit (except Fujifilm products) mounted on the camera
hot shoe.
c
• The flash may not fully light the subject at speeds
faster than 1/1000 s.
• Use auto or custom white balance (P 49).
• If the built-in flash is raised when ON is selected for
g EXTERNAL FLASH, the built-in flash will fire once
to provide a signal for the optional flash unit to fire.
• External flash units can be used in P, S, A, M or EXR
(S and T only) modes.
• Fujifilm external flash units do not require this setting.
a
• The camera can be used with flash units that provide
aperture adjustment, external metering, and sensitivity control. Some flash units that are designed specifically for other cameras can not be used.
• For information on Fujifilm external flash units, see
Accessories from FUJIFILM (P 107).
Menus
K CUSTOM SET
Save settings for P, S, A, M and all EXR modes except R (P 27).
87
Using the Menus: Shooting Mode
v DISP. CUSTOM SETTING
Choose the items displayed in the LCD monitor
(P 6). The following items can be displayed:
FRAMING GUIDLINE*
AF DISTANCE INDICATOR
WHITE BALANCE
HISTOGRAM
IMAGE SIZE/QUALITY
PHOTOMETRY
FILM SIMULATION
EXP. COMPENSATION
ELECTRONIC LEVEL
MF DISTANCE INDICATOR
APERTURE/S-SPEED/ISO
FRAMES REMAINING
BATTERY LEVEL
FLASH
DYNAMIC RANGE
* You can also select the grid type (P 103).
See pages 5 – 6 for the locations of these items in
the displays.
Virtual Horizon
Selecting ELECTRONIC LEVEL
displays a virtual horizon. The
camera is level when the two
lines overlap.
P
1
The virtual horizon may not be displayed if the camera lens is pointed up or down.
88
W MOVIE MODE
Choose a frame size for movies (P 66).
[i]
[i
F AF MODE (F mode)
[[u
u]
This option controls how the camera selects the
focus area for movies.
Option
Description
The camera focuses on the subject in
r CENTER
the center of the frame.
The camera continuously adjusts fou CONTINUOUS cus to reflect changes in the distance
to the subject in the focus frame.
1
Note that in u mode, the camera focuses continuously, increasing the drain on the battery, and that the
sound of the camera focusing may be audible.
Using the Menus: Playback Mode
Using the Playback Menu
Playback Menu Options
Press the a button to enter play1 back
mode.
X PHOTOBOOK ASSIST
Create books from your favorite photos (P 62).
Press MENU/OK to display the play2 back
menu.
Press the selector up or down to
3 highlight
the desired menu item.
Press the selector right to display op4 tions
for the highlighted item.
Press the selector up or down to
5 highlight
the desired option.
6
Press MENU/OK to select the highlighted option.
to exit from the
x ERASE
Delete all or selected pictures (P 59).
j MARK FOR UPLOAD TO
Select pictures for upload to YouTube or Facebook
using MyFinePix Studio (Windows only).
■ Selecting Pictures for Upload
Select YouTube to choose movies for upload
to YouTube, FACEBOOK to choose photos and
movies for upload to Facebook.
1
the selector left or right to display pic2 Press
tures and press MENU/OK to select or deselect.
Press DISP/BACK to exit when all the desired pictures are selected.
Menus
Press DISP/BACK
7 menu.
b IMAGE SEARCH
Search for pictures (P 61).
89
Using the Menus: Playback Mode
1
• Only movies can be selected for upload to YouTube.
• During playback, selected pictures are indicated by
j YouTube or j FACEBOOK icons.
■ RESET ALL: Deselecting All Pictures
Choose RESET ALL to deselect all pictures. If the
number of pictures affected is very large, a message will be displayed while the operation is in
progress. Press DISP/BACK to exit before the operation is complete.
■ Uploading Pictures (Windows Only)
Selected pictures can be uploaded using the
YouTube/Facebook Upload option in MyFinePix
Studio.
Select with camera
Upload from computer
For information on installing MyFinePix Studio
and connecting the camera to a computer, see
“Viewing Pictures on a Computer” (P 76).
90
I SLIDE SHOW
[MULTIPLE]
View pictures in an automated slide show. Choose
the type of show and press MENU/OK to start.
Press DISP/BACK at any time during the show to
view on-screen help. The show can be ended at
any time by pressing MENU/OK.
Option
Description
Press selector left or right to go back or
skip ahead one frame. Select FADE-IN
FADE-IN
for fade transitions between frames.
NORMAL g As above, except that camera automatically zooms in on faces selected with InFADE-IN g telligent Face detection.
MULTIPLE
Display several pictures at once.
NORMAL
1
The camera will not turn off automatically while a slide
show is in progress.
Using the Menus: Playback Mode
j RAW CONVERSION
Create JPEG copies of RAW pictures (P 55). The
original image data are unaffected, allowing a
single RAW image to be processed in a multitude
of different ways.
j RAW CONVER1 Select
SION in the playback menu.
RAW CONVERSION
REFLECT SHOOTING COND.
PUSH/PULL PROCESSING
DYNAMIC RANGE
FILM SIMULATION
WHITE BALANCE
WB SHIFT
CREATE
CANCEL
the selector up or down to highlight a
2 Press
setting and press the selector right to select.
Press the selector up or down to highlight the
desired option and press MENU/OK to select and
return to the settings list. Repeat this step to
adjust additional settings.
Press MENU/OK to save the
copy or press DISP/BACK to
return to Step 2.
STORE
CANCEL
Description
Create a JPEG copy using the setREFLECT SHOOTING
tings in effect at the time the photo
COND.
was taken.
Adjust exposure by –1 EV to +3 EV in
PUSH/PULL
PROCESSING
increments of 1/3 EV (P 44).
Enhance details in highlights for
DYNAMIC RANGE
natural contrast (P 84).
Simulate the effects of different
FILM SIMULATION
types of film (P 85).
WHITE BALANCE
Adjust white balance (P 49).
WB SHIFT
Fine-tune white balance (P 85).
COLOR
Adjust color density (P 85).
SHARPNESS
Sharpen or soften outlines (P 85).
Process the copy to reduce motNOISE REDUCTION
tling (P 85).
HIGHLIGHT TONE
Adjust highlights (P 85).
SHADOW TONE
Adjust shadows (P 85).
Choose the color space used for
COLOR SPACE
color reproduction (P 104).
Menus
Press the RAW button to
3 preview
the JPEG copy.
Setting
91
Using the Menus: Playback Mode
B RED EYE REMOVAL
If the current picture is marked with a g icon to
indicate that it was taken with Intelligent Face Detection, this option can be used to remove redeye. The camera will analyze the image; if red-eye
is detected, the image will be processed to create
a copy with reduced red-eye.
1 Display the desired picture.
B RED EYE REMOVAL in the playback
2 Select
menu.
3 Press MENU/OK.
1
• Red-eye may not be removed if the camera is unable
to detect a face or the face is in profile. Results may
differ depending on the scene. Red-eye can not be
removed from pictures that have already been processed using red-eye removal or pictures created
with other devices.
• The amount of time needed to process the image
varies with the number of faces detected.
• Copies created with B RED EYE REMOVAL are indicated by a e icon during playback.
92
D PROTECT
Protect pictures from accidental deletion.
1 Select D PROTECT in the playback menu.
one of the following options and
2 Highlight
press MENU/OK:
• FRAME: Protect selected pictures. Press the selector left or right to view pictures and press
MENU/OK to select or deselect. Press DISP/BACK
when the operation is complete.
• SET ALL: Protect all pictures.
• RESET ALL: Remove protection from all pictures.
3
Protected pictures will be deleted when the memory
card or internal memory is formatted (P 99).
Using the Menus: Playback Mode
G CROP
Create a cropped copy of the current picture.
O RESIZE
Create a small copy of the current picture.
1 Display the desired picture.
1 Display the desired picture.
2 Select G CROP in the playback menu.
2 Select O RESIZE in the playback menu.
the k and n buttons to zoom the image 3 Highlight a size and press MENU/OK to display a
3 inUseand
out and use the selector to scroll the
confirmation dialog.
picture until the desired portion is displayed.
4
MENU/OK again to save the cropped copy
5 toPress
a separate file.
Press MENU/OK to display a confirmation dialog.
1
Larger crops produce larger copies; all copies have an
aspect ratio of 4 : 3. If the size of the final copy will be
a, OK will be displayed in yellow.
1
The sizes available vary with the size of the original image.
Menus
b Intelligent Face Detection
If the picture was shot with Intelligent Face Detection
(P 52), g will be displayed in the monitor. Press the
f button to zoom in on the selected face.
Press MENU/OK to save the resized copy to a
4 separate
file.
93
Using the Menus: Playback Mode
C IMAGE ROTATE
Rotate pictures taken in tall orientation so that
they are displayed in tall orientation in the LCD
monitor.
1
Select C IMAGE ROTATE in the playback
2 menu.
Display the desired picture.
Press the selector down to rotate the picture
3 90
° clockwise, up to rotate it 90 ° counterclockwise.
MENU/OK. The picture automatically be
4 Press
displayed in the selected orientation whenever it is played back on the camera.
1
• Protected pictures can not be rotated. Remove protection before rotating pictures (P 92).
• The camera may not be able to rotate pictures created with other devices.
E COPY
Copy pictures from internal memory to a memory
card.
1 Select E COPY in the playback menu.
one of the following options and
2 Highlight
press the selector right:
• a INTERNAL MEMORY y b CARD: Copy pictures from internal memory to a memory
card.
• b CARD y a INTERNAL MEMORY: Copy pictures from a memory card to internal memory.
one of the following options and
3 Highlight
press MENU/OK:
• FRAME: Copy selected pictures. Press the selector left or right to view pictures and press
MENU/OK to copy the current picture.
• ALL FRAMES: Copy all pictures.
1
• Copying ends when the destination is full.
• DPOF print information is not copied (P 73).
94
Using the Menus: Playback Mode
F VOICE MEMO
Add a voice memo to the current photograph.
Holding the camera at a distance of about 20 cm,
face the microphone and press MENU/OK to begin
recording. Press MENU/OK again to end recording
(recording ends automatically after 30 seconds).
1
• Voice memos can not be added to movies or protected pictures. Remove protection from pictures before
recording voice memos.
• If a voice memo already exists for the current picture,
the options will be displayed. Select RE-REC to replace the existing memo.
Playing Voice Memos
Pictures with voice memos are indicated by a q icon
during playback. To play the voice memo back, select
PLAY for F VOICE MEMO in the playback menu.
1
Face recognition links can not be removed from copies
with a size of a or smaller.
K PRINT ORDER (DPOF)
Select pictures for printing on DPOF- and PictBridge-compatible devices (P 71).
Menus
1
• The camera may not play voice memos recorded
with other devices.
• Do not cover the speaker during playback.
n ERASE FACE RECOG.
Remove face recognition links from the current
image. When this option is selected, the camera
will zoom in on an area in the current picture that
it has matched with a face in the face recognition
database. If the match is not correct, press MENU/
OK to remove the link to the face recognition database.
95
Using the Menus: Playback Mode
J DISP. ASPECT
[4 : 3]
Choose how High Definition (HD) devices display
pictures with an aspect ratio of 4 : 3 (this option is
available only when an HDMI cable is connected).
Select 16 : 9 to display the image so that it fills the
screen with its top and bottom cropped out, 4 : 3
to display the entire image with black bands at
either side.
16 : 9
4 :3
16 : 9
4:3
1
Photographs with an aspect ratio of 16 : 9 are displayed
full screen, those with an aspect ratio of 3 : 2/1 : 1 in a
black frame.
96
The Setup Menu
Using the Setup Menu
the setup menu.
1 Display
1.1 Press MENU/OK to display
the
menu for the current mode.
1.2 Press the selector left to highlight a left tab.
1.3 Press the selector up or down
to select 4.
The setup menu appears.
SET-UP
SET
SET
EXIT
Adjust settings.
2 2.1
Press the selector right to activate the setup menu.
2.2 Press the selector up or down
to highlight a menu item.
2.3 Press the selector right to display options for the highlighted
item.
2.4 Press the selector up or down
to highlight an option.
Tab
2.6 Press DISP/BACK to exit from the
menu.
Menus
2.5 Press MENU/OK to select the
highlighted option.
97
The Setup Menu
Setup Menu Options
Default values are shown in square brackets [ ].
F DATE/TIME
Set the camera clock (P 17).
N TIME DIFFERENCE
[h
[h]
Switch the camera clock instantly from your
home time zone to the local time at your destination when traveling. To specify the difference
between local time and your home time zone:
Highlight g LOCAL and press the selector
1 right.
Use the selector to choose the time difference
2 between
local time and your home time zone.
3 Press MENU/OK.
To switch between local time and your home
time zone, highlight g LOCAL or h HOME and
press MENU/OK.
98
Option
h HOME
g LOCAL
Description
Switch to the time currently selected
for F DATE/TIME (see above).
Switch to local time. If this option is
selected, g and the time and date
will be displayed in yellow for three
seconds each time the camera is
turned on.
La
Choose a language (P 17).
o SILENT MODE
[OFF]
Select ON to disable the speaker, flash, and AFassist illuminator in situations in which camera
sounds or lights may be unwelcome (note that
the flash will still fire in C mode).
The Setup Menu
R RESET
Reset all settings except F DATE/TIME, N TIME
DIFFERENCE, O BACKGROUND COLOR, and
Q VIDEO SYSTEM to default values.
R RESET and press the selector
1 Highlight
right to display a confirmation dialog.
2
Highlight OK and press MENU/OK.
K FORMAT
If a memory card is inserted in the camera, this
option will format the memory card. If no memory card is inserted, this option will format internal
memory.
Option
3 SEC
1.5 SEC
ZOOM
(CONTINUOUS)
OFF
Description
Pictures are displayed for three seconds (3 SEC) or 1.5 seconds (1.5 SEC).
Colors may differ slightly from those
in the final image.
Pictures are displayed until the MENU/
OK button is pressed.
Pictures are not displayed after shooting.
1
OFF has no effect in continuous shooting mode.
Menus
3
• All data—including protected pictures—will be deleted from the memory card or internal memory. Be
sure important files have been copied to a computer
or other storage device.
• Do not open the battery-chamber cover during formatting.
A IMAGE DISP.
[1.5 SEC]
Choose how long pictures are displayed in the
LCD monitor after shooting.
99
The Setup Menu
B FRAME NO.
[CONT.]
New pictures are stored in im- Frame number
age files named using a four100-0001
digit file number assigned
File
by adding one to the last file Directory
number used. The file num- number number
ber is displayed during playback as shown at right. B FRAME NO. controls
whether file numbering is reset to 0001 when a
new memory card is inserted or the current memory card or internal memory is formatted.
Option
CONTINUOUS
RENEW
100
Description
Numbering continues from the last
file number used or the first available file number, whichever is higher.
Choose this option to reduce the
number of pictures with duplicate
file names.
Numbering is reset to 0001 after formatting or when a new memory card
is inserted.
1
• If the frame number reaches 999-9999, the shutter
release will be disabled (P 117).
• Selecting R RESET (P 99) sets B FRAME NO. to
CONTINUOUS but does not reset the file number.
• Frame numbers for pictures taken with other cameras may differ.
G OPERATION VOL.
[c]
[c
Adjust the volume of the sounds produced when
camera controls are operated. Choose e OFF
(mute) to disable control sounds.
H SHUTTER VOLUME
[c]
[c
Adjust the volume of the sounds produced when
the shutter is released. Choose e OFF (mute) to
disable the shutter sound.
e SHUTTER SOUND
Choose the sound made by the shutter.
[i]
[i
The Setup Menu
I PLAYBACK VOLUME
[7]
Adjust the volume for movie and voice memo
playback.
L DUAL IS MODE
[[L
L]
Choose from the following image stabilization
options:
J LCD BRIGHTNESS
Control the brightness of the display.
Option
L CONTINUOUS +
MOTION
l CONTINUOUS
M SHOOTING
+ MOTION
m SHOOTING ONLY
[0]
M AUTO POWER OFF
[2 MIN]
Choose the length of time before the camera
turns off automatically when no operations are
performed. Shorter times increase battery life; if
OFF is selected, the camera must be turned off
manually. Note that in some situations the camera turns off automatically even when OFF is selected.
1 QUICK START MODE
[OFF]
Allow the camera to restart in a fast manner after
turned off (ON/OFF).
3
+ MOTION has no effect when sensitivity is set to a
fixed value, and may also be unavailable at some other
combinations of settings. The effect may vary with
lighting conditions and the speed at which the object
is moving.
Menus
3
This option will increase drain on the battery.
OFF
Description
Image stabilization on. If + MOTION
is selected, the camera will adjust
shutter speed to reduce motion blur
when a moving objects are detected.
As above, except that image stabilization is performed only when the
shutter button is pressed halfway or
the shutter is released.
Image stabilization off. Choose this
option when using a tripod.
F Fn BUTTON
[N
[N ISO]
Choose the role played by the Fn button (P 51).
101
The Setup Menu
B RED EYE REMOVAL
[OFF]
Choose ON to remove red-eye effects caused by
the flash when shooting with Intelligent Face Detection.
1
• Red-eye reduction is performed only when a face is
detected.
• Red-eye removal is not available with RAW images.
C AF ILLUMINATOR
[ON]
If ON is selected, the AF-assist illuminator will light
to assist autofocus.
3
• The camera may be unable to focus using the AF-assist illuminator in some cases. If the camera is unable
to focus in macro mode, try increasing the distance to
the subject.
• Avoid shining the AF-assist illuminator directly into
your subject’s eyes.
102
k AE/AF-LOCK MODE
[P]
If AE&AF ON WHEN PRESSING is selected, exposure and/or focus will lock while the AFL/AEL button is pressed. If AE&AF ON/OFF SWITCH is selected, exposure and/or focus will lock while the
AFL/AEL button is pressed and remain locked until
the button is pressed again (P 35).
v AE/AF-LOCK BUTTON
[AE-L]
Choose whether the AFL/AEL button locks only
exposure, only focus, or both exposure and focus
(AE-L / AF-L / AE+AF).
j RAW
[OFF]
Choose whether RAW pictures are recorded
(P 55).
j FOCUS CHECK
[ON]
If ON is selected for j FOCUS CHECK, the image will be magnified in the display to assist focus
when the sub-command dial is rotated in manual
focus mode (P 46, 47). The camera must be in
manual focus mode.
The Setup Menu
I FOCUS CONTROL DIAL
[X
[X CW]
Choose the direction in which the sub-command
dial is rotated to increase the focus distance.
M FOCUS SCALE UNITS
[METERS]
Choose the units used for the focus distance indicator (P 46).
z FRAMING GUIDLINE
Choose the type of framing grid available in shooting mode.
F GRID 9
P
For “rule of thirds” composition.
[F GRID 9]
[F
G GRID 24
P
A six-by-four grid.
H HD FRAMING
P
Frame HD pictures in the crop shown
by the lines at the top and bottom of
the display.
Menus
103
The Setup Menu
J COLOR SPACE
[sRGB]
Choose the gamut of colors available for color reproduction.
Option
sRGB
Adobe RGB
Description
Recommended in most situations.
For commercial printing.
t SAVE ORG IMAGE
[OFF]
Choose ON to save unprocessed copies of seamless z panoramas or pictures taken using
B RED EYE REMOVAL, j PRO LOW-LIGHT
MODE, or i PRO FOCUS MODE.
m AUTOROTATE PB
[ON]
Choose ON to automatically rotate “tall” (portraitorientation) pictures during playback.
O BACKGROUND COLOR
Choose a color scheme.
c GUIDANCE DISPLAY
Choose whether to display tool tips.
[ON]
Q VIDEO SYSTEM
Choose a video mode for connection to a TV.
Option
NTSC
PAL
104
[BLACK]
Description
Select this mode for connection to
video devices in North America, the
Caribbean, parts of Latin America,
and some East Asian countries.
Select this mode for connection to
video devices in the United Kingdom
and much of Europe, Australia, New
Zealand, and parts of Asia and Africa.
The Setup Menu
S CUSTOM RESET
Reset all settings for mode C1/C2. A confirmation
dialog will be displayed, press the selector up or
down to highlight OK and press MENU/OK.
x POWER MANAGEMENT
[[n
n]
Optimize camera performance for increased battery life or display quality.
Description
Reduces display refresh rate. The display dims to save power if no operations are performed for a short perin POWER SAVE
od, but can be restored by operating
camera controls. Select this option to
save power.
Choose this option for a brighter,
higher quality display and for a lono CLEAR
ger delay before the monitor dims to
DISPLAY
save power.
Option
n POWER SAVE does not take effect when Intelligent
Face Detection is on.
Menus
1
105
Optional Accessories
The camera supports a wide range of accessories from FUJIFILM and other manufacturers.
■ Flash Photography
■ Audio/Visual
Standard TV (available from
third-party suppliers)
EF-20 shoe
mount flash
(sold separately)
A/V cable
EF-42 shoe
mount flash
(sold separately)
DIGITAL CAMERA
X10
HDTV (available from
third-party suppliers)
USB
HDMI cable
Technical Notes
Computer (available from
third-party suppliers)
SD/SDHC/SDXC
memory card
■ Printing
USB
PictBridge-compatible printer
(available from third-party suppliers)
106
■ Computer Related
SD card slot or card reader
Printer (available from
third-party suppliers)
Optional Accessories
Accessories from FUJIFILM
The following optional accessories are available from FUJIFILM. For the latest information on the accessories available in your region, check with your local FUJIFILM representative or visit http://www.fujifilm.
com/products/digital_cameras/index.html.
Rechargeable
Li-ion batteries
NP-50: Additional large-capacity NP-50 rechargeable batteries can be
purchased as required.
Battery chargers BC-45W: Replacement battery chargers can be purchased as required. The
BC-45W charges an NP-50 battery in about 150 minutes at +20 °C (+68 °F).
AC power
adapters
DC couplers
CP-50: Connect the AC-5VX to the camera.
Technical Notes
A/V cable
AC-5VX (requires CP-50 DC coupler): Use for extended playback or when copying
pictures to a computer (shape of adapter and plug vary with region of
sale).
AV-C1: Use for viewing pictures on TV.
Shoe Mount Flash EF-20: Hot-shoe clip-on flash, guide number: 20 (ISO 100), compatible with
i-TTL, bounce capability: up to 90°, power source: 2 AA-size 1.5V batteries
107
Optional Accessories
Shoe Mount Flash EF-42: Hot-shoe clip-on flash, guide number: up to 42 (ISO 100), auto zoom:
24-105mm (equivalent to 135 format), compatible with i-TTL, bounce capability: up to 90°, power source: 4 AA-size 1.5V batteries
Set “Format setting” to “35 mm” when using EF-42 and X10.
108
Leather cases
LC-X10: This leather case, exclusively for use with the X10, combines practicality with the luxury of leather and comes with a shoulder strap made of
the same material. Pictures can be taken with the camera still in its case.
Lens hood
LH-X10: This aluminum lens hood, exclusively for use with the X10, comes
with an adapter ring made of the same material. The adapter ring is also
used when attaching the φ52 mm filters available from third-party suppliers.
Optional Accessories
Attaching the Lens Hoods
Connect the lens
1 hood
and the adapt-
Adapter ring
Attaching the Filters (available from
third-party suppliers)
the adapter
1 Remove
ring from the lens
er ring as shown.
hood as shown.
Lens hood
Attach the lens
2 hood
to the camera
a
Keep the lens cap in a safe place when not in use.
Rotate the adapter
ring as shown.
the filter to the adapter ring.
3 Attach
For details, please refer to the manual supplied with the filter.
a
• Only φ52 mm filters can be attached.
• Keep the lens cap in a safe place when not in use.
• Filters cannot be attached directly to the camera.
Make sure to use the adapter ring.
• The lens hood can be attached after the filter is attached.
Technical Notes
with the connected
adapter ring.
Rotate the lens hood
as shown.
Attach the adapter
2 ring
to the camera.
109
Caring for the Camera
To ensure continued enjoyment of the product, observe the following precautions.
Storage and Use
If the camera will not be used for an extended period, remove the battery and memory card. Do
not store or use the camera in locations that are:
• exposed to rain, steam, or smoke
• very humid or extremely dusty
• exposed to direct sunlight or very high temperatures, such as in a closed vehicle on a sunny day
• extremely cold
• subject to strong vibration
• exposed to strong magnetic fields, such as near
a broadcasting antenna, power line, radar emitter, motor, transformer, or magnet
• in contact with volatile chemicals such as pesticides
• next to rubber or vinyl products
■ Water and Sand
Exposure to water and sand can also damage the
camera and its internal circuitry and mechanisms.
When using the camera at the beach or seaside,
avoid exposing the camera to water or sand. Do
not place the camera on a wet surface.
110
■ Condensation
Sudden increases in temperature, such as occur
when entering a heated building on a cold day,
can cause condensation inside the camera. If this
occurs, turn the camera off and wait an hour before turning it on again. If condensation forms on
the memory card, remove the card and wait for
the condensation to dissipate.
Cleaning
Use a blower to remove dust from the lens and
monitor, then gently wipe with a soft, dry cloth.
Any remaining stains can be removed by wiping
gently with a piece of FUJIFILM lens-cleaning paper to which a small amount of lens-cleaning fluid
has been applied. Care should be taken to avoid
scratching the lens or monitor. The camera body
can be cleaned with a soft, dry cloth. Do not use
alcohol, thinner, or other volatile chemicals.
Traveling
Keep the camera in your carry-on baggage.
Checked baggage may suffer violent shocks that
could damage the camera.
Problems and Solutions
Power and Battery
Problem
Troubleshooting
Solution
• The zoom ring (ON/OFF switch) is not correctly rotated: Rotate the zoom ring to OFF and then rotate the
zoom ring again to the point between 28 and 112 (P 15).
• The battery is exhausted: Charge the battery or insert a fully-charged spare battery (P 10).
The camera does not
• The battery is inserted incorrectly: Reinsert in the correct orientation (P 11).
turn on.
• The battery-chamber cover is not latched: Latch the battery-chamber cover (P 11).
• The AC power adapter and DC coupler are connected incorrectly: Reconnect the AC power adapter and
DC coupler.
• The battery is cold: Warm the battery by placing it in a pocket or other warm place and reinsert it
in the camera immediately before taking a picture.
• There is dirt on the battery terminals: Clean the terminals with a soft, dry cloth.
• o CLEAR DISPLAY is selected for x POWER MANAGEMENT: Select n POWER SAVE to reduce the
drain on the battery (P 105).
The battery runs down
• R is selected for shooting mode: Select B mode to reduce the drain on the battery (P 23).
quickly.
• x TRACKING is selected for F AF MODE: Select a different AF mode (P 86).
• AF-C is selected for focus mode: Select a different focus mode (P 46).
• The battery has been charged many times: The battery has reached the end of its charging life. Purchase a new battery.
• The zoom ring (ON/OFF switch) is not correctly rotated: Rotate the zoom ring to OFF and then rotate the
zoom ring again to the point between 28 and 112 (P 15).
The camera turns off
• The battery is exhausted: Charge the battery or insert a fully-charged spare battery (P 10).
suddenly.
• The AC power adapter or DC coupler has been disconnected: Reconnect the AC power adapter and DC
coupler.
Charging does not start. Reinsert the battery in the correct orientation and make sure that the charger is plugged in (P 10).
Charging is slow.
Charge the battery at room temperature (P vi).
• There is dirt on the battery terminals: Clean the terminals with a soft, dry cloth.
The charging lamp lights,
• The battery has been charged many times: The battery has reached the end of its charging life. Purbut the battery does not
chase a new battery. If the battery still fails to charge, contact your FUJIFILM dealer.
charge.
• The battery is too hot or too cold: Wait for the battery temperature to stabilize (P 10).
111
Problems and Solutions
Menus and Displays
Problem
Menus and displays are
not in English.
Solution
Select ENGLISH for Q a (P 17, 98).
Shooting
Problem
•
•
•
No picture is taken when
•
the shutter button is
•
pressed.
•
•
The LCD monitor goes
dark after shooting.
Solution
Memory is full: Insert a new memory card or delete pictures (P 12, 59).
Memory is not formatted: Format the memory card or internal memory (P 99).
There is dirt on the memory card contacts: Clean the contacts with a soft, dry cloth.
The memory card is damaged: Insert a new memory card (P 12).
The battery is exhausted: Charge the battery or insert a fully-charged spare battery (P 10).
The camera has turned off automatically: Turn the camera on (P 15).
The indicator lamp was orange when you attempted to record a panorama: Wait until the indicator lamps
turns off (P 21).
The LCD monitor may darken while the flash charges. Wait for the flash to charge (P 37).
• The subject is close to the camera: Select macro mode (P 36).
• The subject is far away from the camera: Cancel macro mode (P 36).
• The subject is not suited to autofocus: Use focus lock (P 34).
If S is selected for O IMAGE SIZE in R mode, the camera will optimize not only sensitivity and
Pictures are not the same
other settings, but also image size. To record all pictures at the same size, choose another shooting
size.
mode or select another option for O IMAGE SIZE (P 83).
Macro mode is not availChoose a different shooting mode (P 23).
able.
Intelligent Face Detection Intelligent Face Detection is not available in the current shooting mode: Choose a different shooting mode
is not available.
(P 23).
The camera does not
focus.
112
Problems and Solutions
Problem
No face is detected.
Wrong subject is selected.
The flash does not fire.
Some flash modes are
not available.
Pictures are blurred.
Pictures are mottled.
Troubleshooting
The flash does not fully
light the subject.
Solution
• The subject’s face is obscured by sunglasses, a hat, long hair, or other objects: Remove the obstructions.
• The subject’s face occupies only a small area of the frame: Change the composition so that the subject’s face occupies a larger area of the frame (P 34).
• The subject’s head is tilted or horizontal: Ask the subject to hold their head straight.
• The camera is tilted: Keep the camera level (P 19).
• The subject’s face is poorly lit: Shoot in bright light.
The selected subject is closer to the center of the frame than the main subject. Recompose the
picture or turn face detection off and frame the picture using focus lock (P 34).
• The flash is not available in the current shooting mode: Choose a different shooting mode (P 23).
• The camera is in super macro or continuous shooting mode: Turn super macro and continuous shooting
modes off (P 36).
• The battery is exhausted: Charge the battery or insert a fully-charged spare battery (P 10).
• The camera is in silent mode: Turn silent mode off (P 98).
• The flash is not raised: Raise the flash (P 37).
• The desired flash mode is not available in the current shooting mode: Choose a different shooting mode
(P 23).
• The camera is in silent mode: Turn silent mode off (P 98).
• The subject is not in range of the flash: Position the subject in range of the flash (P 122).
• The flash window is obstructed: Hold the camera correctly (P 19).
• Fast shutter speed selected: Choose a slower shutter speed (P 25, 26).
• The lens is dirty: Clean the lens (P 110).
• The lens is blocked: Keep objects away from the lens (P 19).
• s is displayed during shooting and the focus frame is displayed in red: Check focus before shooting
(P 116).
• k is displayed during shooting: Use the flash or a tripod (P 37).
• A slow shutter speed is selected at high temperatures: This is normal and does not indicated a malfunction.
• The camera has been used continuously at high temperatures or a temperature warning is displayed: Turn
the camera off and wait for it to cool down.
113
Problems and Solutions
Problem
Solution
Power was interrupted during shooting. Before connecting the AC power adapter or DC coupler,
Pictures are not recorded. turn the camera off. Leaving the camera on can result in corrupted files or damage to the memory
card or internal memory.
The viewfinder display is Diopter adjustment is not adjusted correctly: Slide the diopter adjustment control up and down until the
not clear.
viewfinder display is in sharp focus (P 4).
LCD monitor displays
Display mode is set to LCD SWITCHED OFF: Press DISP/BACK to choose a different display mode (P 6).
nothing.
Sounds made by the
• u CONTINUOUS is selected for F AF MODE: Select a different AF mode (P 86).
camera are recorded with
• Intelligent Face Detection is on: Turn Intelligent Face Detection off (P 52).
movies.
Playback
Problem
Pictures are grainy.
Playback zoom unavailable.
Solution
The pictures were taken with a different make or model of camera.
The picture has been saved at a, or is from another make or model of camera (P 57).
• The camera is in silent mode: Turn silent mode off (P 98).
No sound in voice memo • Playback volume is too low: Adjust playback volume (P 101).
and movie playback.
• The microphone was obstructed: Hold the camera correctly during recording (P 2).
• The speaker is obstructed: Hold the camera correctly during playback (P 2).
Selected pictures are not Some of the pictures selected for deletion are protected. Remove protection using the device
deleted.
with which it was originally applied (P 92).
File numbering is unex- The battery-chamber cover was opened while the camera was on. Turn the camera off before
pectedly reset.
opening the battery-chamber cover (P 15).
114
Problems and Solutions
Connections/Miscellaneous
Problem
No picture or sound.
The camera is unresponsive.
The camera does not
function as expected.
I want to use an AC
power adapter and DC
coupler overseas.
No sound.
Be sure the camera and computer are correctly connected (P 80).
Use the bundled software to transfer pictures (P 76).
• The camera is not properly connected: Connect the camera correctly (P 70).
• The printer is off: Turn the printer on.
The printer is not PictBridge compatible.
• Temporary camera malfunction: Remove and reinsert the battery (P 11) or disconnect and reconnect the AC power adapter/DC coupler.
• The battery is exhausted: Charge the battery (P 10) or insert a fully-charged spare battery (P 11).
Remove and reinsert the battery (P 11) or disconnect and reconnect the AC power adapter/DC
coupler. If the problem persists, contact your FUJIFILM dealer.
Check the label on the AC power adapter. The AC power adapter can be used with voltages of
100 – 240 V. Consult your travel agent for information on plug adapters.
Troubleshooting
No color
The computer does not
recognize the camera.
Can not transfer RAW or
JPEG files to computer.
Pictures can not be
printed.
Only one copy is printed/
the date is not printed.
Solution
• The camera is not properly connected: Connect the camera properly (P 68).
• An A/V cable was connected during movie playback: Connect the camera once movie playback has
ended.
• Input on the television is set to “TV”: Set input to “VIDEO”.
• The camera is not set to the correct video standard: Match the camera Q VIDEO SYSTEM setting to
the TV (P 104).
• The volume on the TV is too low: Adjust the volume.
Match the camera Q VIDEO SYSTEM setting to the TV (P 104).
Turn silent mode off (P 98).
115
Warning Messages and Displays
The following warnings are displayed in the LCD monitor:
Warning
B (red)
A (blinks red)
k
Description
Low battery. Charge the battery (P 10) or insert a fully-charged spare battery (P 11).
Battery exhausted. Charge the battery (P 10) or insert a fully-charged spare battery (P 11).
Slow shutter speed. Pictures may be blurred; use the flash or a tripod.
The camera can not focus. Try one of the following solutions:
s
• Use focus lock to focus on another subject at the same distance, then recompose the picture
(displayed in red with red
(P 34).
focus frame)
• Use macro mode to focus when taking close-ups (P 36).
Aperture or shutter
The subject is too bright or too dark and the picture will be over- or under-exposed. If the subject
speed displayed in red is dark, use the flash (P 37).
FOCUS ERROR
TURN OFF THE CAMERA AND Camera malfunction. Turn the camera off and then on again. If the message persists, contact a
TURN ON AGAIN
FUJIFILM dealer.
LENS CONTROL ERROR
• The memory card or internal memory is not formatted or the memory card was formatted in a computer or
other device: Format the memory card or internal memory using the K FORMAT option in the
camera setup menu (P 99).
CARD NOT INITIALIZED
• The memory card contacts require cleaning: Clean the contacts with a soft, dry cloth. If the message
is repeated, format the card (P 99). If the message persists, replace the card.
• Camera malfunction: Contact a FUJIFILM dealer.
PROTECTED CARD
The memory card is locked. Unlock the card (P 12).
BUSY
The memory card is incorrectly formatted. Use the camera to format the card (P 99).
Turn the camera off and wait for it to cool. If no action is taken, the camera will turn off automatip
cally.
116
Warning Messages and Displays
Warning
CARD ERROR
a MEMORY FULL
b MEMORY FULL
INTERNAL MEMORY IS FULL
INSERT A NEW CARD
WRITE ERROR
FRAME NO. FULL
PRESS AND HOLD
THE DISP BUTTON TO
DEACTIVATE SILENT MODE
TOO MANY FRAMES
The memory card or internal memory is full and pictures can not be recorded or copied. Delete
pictures or insert a memory card with more free space.
• Memory card error or connection error: Reinsert the card or turn the camera off and then on again.
If the message persists, contact a FUJIFILM dealer.
• Not enough memory remaining to record additional pictures: Delete pictures or insert a memory card
with more free space.
• The memory card or internal memory is not formatted: Format the memory card or internal memory
(P 99).
• The file is corrupt or was not created with the camera: The file can not be viewed.
• The memory card contacts require cleaning: Clean the contacts with a soft, dry cloth. If the message
is repeated, format the card (P 99). If the message persists, replace the card.
• Camera malfunction: Contact a FUJIFILM dealer.
The camera has run out of frame numbers (current frame number is 999-9999). Format the memory card and select RENEW for B FRAME NO. Take a picture to reset frame numbering to 100-0001,
then select CONTINUOUS for B FRAME NO. (P 100).
Troubleshooting
READ ERROR
Description
The memory card is not formatted for use in the camera. Format the card (P 99).
The memory card contacts require cleaning or the memory card is damaged. Clean the contacts
with a soft, dry cloth. If the message is repeated, format the card (P 99). If the message persists,
replace the card.
Incompatible memory card. Use a compatible card (P 14).
Camera malfunction. Contact a FUJIFILM dealer.
An attempt was made to choose a flash mode or adjust the volume with the camera in silent mode.
Exit silent mode before choosing a flash mode or adjusting the volume (P 21).
• A search has returned more than 30,000 results: Choose a search that returns fewer results.
• More than 999 images are selected for deletion: Choose fewer images.
117
Warning Messages and Displays
Warning
PROTECTED FRAME
a CAN NOT CROP
CAN NOT CROP
P CANNOT EXECUTE
Q CANNOT EXECUTE
a CANNOT EXECUTE
CAN NOT ROTATE
F CAN NOT ROTATE
m CANNOT EXECUTE
F CANNOT EXECUTE
NO CARD
b NO IMAGE
a NO IMAGE
u ERROR
DPOF FILE ERROR
CAN NOT SET DPOF
F CAN NOT SET DPOF
COMMUNICATION ERROR
PRINTER ERROR
PRINTER ERROR
RESUME?
118
Description
An attempt was made to delete, rotate, or add a voice memo to a protected picture. Remove
protection and try again (P 92).
a pictures can not be cropped.
The picture is damaged or was not created with the camera.
An attempt was made to create a resized copy at a size equal to or larger than the original. Choose
a smaller size.
An attempt was made to rotate a picture that can not be rotated.
Movies can not be rotated.
Red-eye removal can not be applied to the selected picture.
Red-eye removal can not be applied to movies.
No memory card inserted when E COPY is selected. Insert a memory card.
The source selected for E COPY contains no images. Select a different source.
• The voice memo file is corrupt: The voice memo can not be played back.
• Camera malfunction: Contact a FUJIFILM dealer.
The DPOF print order on the current memory card contains more than 999 images. Copy the
pictures to internal memory and create a new print order.
The picture can not be printed using DPOF.
Movies can not be printed using DPOF.
A connection error occurred while pictures were being printed or copied to a computer or other
device. Confirm that the device is turned on and that the USB cable is connected.
Printer out of paper or ink, or other printer error. Check printer (see printer manual for details). To
resume printing, turn the printer off and then turn it back on.
Printer out of paper or ink, or other printer error. Check printer (see printer manual for details). If
printing does not resume automatically, press MENU/OK to resume.
Warning Messages and Displays
Warning
CANNOT BE PRINTED
Description
An attempt was made to print a movie, a picture not created with the camera, or a picture in a
format not supported by the printer. Movies and some pictures created with other devices can
not be printed; if the picture is a still picture created with the camera, check the printer manual to
confirm that the printer supports the JFIF-JPEG or Exif-JPEG format. If it does not, the pictures can
not be printed.
Troubleshooting
119
Internal Memory/Memory Card Capacity
The following table shows the recording time or number of pictures available at different image sizes.
All figures are approximate; file size varies with the scene recorded, producing wide variations in the
number of files that can be stored. The number of exposures or length remaining may not diminish at
an even rate. A limited number of test pictures can be taken when no memory card is inserted.
Medium
O
Photographs
Movie
Appendix
120
T
O 4:3
O 16:9
P 4:3
P 16:9
Q 4:3
Q 16:9
i 1920 1
h 1280 1
f2
Y 640 × 480 3
Y 320 × 240 3
Y 320 × 112 3
Internal memory
(approx. 26 MB)
FINE
NORMAL
5
8
7
11
8
16
11
22
16
30
23
35
12 sec.
17 sec.
42 sec.
32 sec.
65 sec.
32 sec.
4 GB
FINE
820
1090
1310
1740
2430
3540
8 GB
NORMAL
1300
1720
2530
3350
4590
5160
38 min.
49 min.
115 min.
85 min.
172 min.
86 min.
1 Use a G card or better. Individual movies can not exceed 29 minutes in length.
2 Individual movies can not exceed 115 minutes in length.
3 Use a G card or better. Individual movies can not exceed 30 seconds in length.
FINE
1650
2200
2640
3500
4880
7110
NORMAL
2620
3450
5080
6720
9210
10370
76 min.
98 min.
232 min.
112 min.
345 min.
172 min.
Specifications
System
Model
Effective pixels
Image sensor
Storage media
File system
Appendix
Digital Camera X10
12 million
2/
3 -in., EXR CMOS with primary color filter
• Internal memory (approx. 26 MB)
• SD/SDHC/SDXC memory cards
Compliant with Design Rule for Camera File System (DCF), Exif 2.3, and Digital Print Order Format
(DPOF)
File format
• Still pictures: Exif 2.3 JPEG (compressed); RAW (original RAF format, special-purpose software required); RAW+JPEG
available
• Movies: MOV (H.264) (stereo)
• Audio: WAV (stereo)
Image size (pixels)
• O 4 : 3: 4,000 × 3,000 • O 3 : 2: 4,000 × 2,664 • O 16 : 9: 4,000 × 2,248 • O 1 : 1: 2,992 × 2,992
• P 4 : 3: 2,816 × 2,112 • P 3 : 2: 2,816 × 1,864 • P 16 : 9: 2,816 × 1,584 • P 1 : 1: 2,112 × 2,112
• Q 4 : 3: 2,048 × 1,536 • Q 3 : 2: 2,048 × 1,360 • Q 16 : 9: 1,920 × 1,080 • Q 1 : 1: 1,536 × 1,536
• r MOTION PANORAMA v: 1,624 × 11,520 (tall)/11,520 × 1,080 (wide)
• r MOTION PANORAMA w: 1,624 × 5,760 (tall)/5,760 × 1,080 (wide)
• r MOTION PANORAMA x: 1,624 × 3,840 (tall)/3,840 × 1,080 (wide)
• r MOTION PANORAMA z: 1,624 × 11,520 (tall)/11,520 × 1,080 (wide)
Digital zoom
About 2.0 × with intelligent digital zoom (up to 8 × when combined with optical zoom)
Lens
Fujinon 4 × optical zoom lens, F2.0 (wide angle)–F2.8 (telephoto)
Focal length
f=7.1 mm–28.4 mm (35-mm format equivalent: 28 mm– 112 mm)
Aperture
F2.0–F11 (wide angle)/F2.8–F11 (telephoto) in increments of 1/3 EV
Focus range (distance from • Approx. 50 cm (1.6 ft.)–infinity (wide angle); 80 cm (2.6 ft.)–infinity (telephoto)
front of lens)
• Macro: approx. 10 cm–3 m/0.3 ft.–9.8 ft. (wide angle); 50 cm–5 m/1.6 ft.–16.4 ft. (telephoto)
• Super macro: approx. 1 cm–1 m/0.3 in.–3.2 ft. (wide angle)
Sensitivity
Standard output sensitivity equivalent to ISO 100, 200, 250, 320, 400, 500, 640, 800, 1000, 1250, 1600,
2000, 2500, 3200, 40001, 50001, 64001, 128002; AUTO, AUTO (400), AUTO (800), AUTO (1600), AUTO (3200)
1 image size P or Q
2 image size Q
Metering
256-segment through-the-lens (TTL) metering; MULTI, SPOT, AVERAGE
121
Specifications
System
Exposure control
Exposure compensation
Scene modes
Programmed AE (with program shift), shutter-priority AE, aperture-priority AE, and manual exposure
–2 EV – +2 EV in increments of 1/3 EV
C (NATURAL & N), D (NATURAL LIGHT), L (PORTRAIT), Z (PORTRAIT ENHANCER),
M (LANDSCAPE), N (SPORT), O (NIGHT), H (NIGHT (TRIPOD)), U (FIREWORKS), Q (SUNSET),
R (SNOW), V (BEACH), f (UNDERWATER), U (PARTY), V (FLOWER), W (TEXT)
Picture stabilization
Optical stabilization (lens-shift type)
Shutter speed (combined • O: 1/4 s–1/1,000 s
• H: 3 s–1/1,000 s
• U: 4 s–1/2 s
mechanical and electronic • P, AUTO, Adv., SP (except O, H, and U): 1/4 s–1/4,000 s
shutter)
• Other modes: 30 s–1/4,000 s
Continuous
• I: max. 200 frames; frame rate can be selected from 10, 7, 5, and 3 fps (The frame rate varies depending on the
shooting conditions or numbers of frames in continuous shooting.)
• P: 16 or 8 frames (RAW+JPEG/RAW: max. 8 frames); frame rate can be selected from 10, 7, 5, and 3 fps
• O: 3 frames (selected exposure, overexposure, underexposure)
• W: 3 frames (selected sensitivity, sensitivity raised, sensitivity lowered)
• X: 3 frames (PROVIA, Velvia, ASTIA)
• Y: 3 frames (100%, 200%, 400%)
Focus
• Mode: Single AF, continuous AF, manual focus
• Focus-area selection: Multi, area, tracking
• Autofocus system: Contrast-detect TTL AF
White balance
Automatic scene detection; 8 manual preset modes for direct sunlight, shade, daylight fluorescent,
warm white fluorescent, cool white fluorescent, incandescent lighting, underwater, color temperature ; custom white balance
Self-timer
Off, 2 sec., 10 sec.
Flash
Manual pop-up flash; effective range when sensitivity is set to AUTO (800) is approx. 30 cm–7.0 m/0.9 ft.–
22.9 ft. (wide angle), 50 cm–5.0 m/1.6 ft.–16.4 ft. (telephoto)
Flash modes
Auto, forced flash, off, slow synchro (red-eye removal off); auto with red-eye removal, forced flash
with red-eye removal, off, slow sync with red-eye removal (red-eye removal on)
Optical viewfinder
Optical zoom viewfinder; frame coverage approx. 85%
Monitor
2.8-in., 460k-dot color LCD monitor; frame coverage approx. 100%
122
Specifications
System
Movies
Languages
Input/output terminals
A/V OUT (audio/video output)
HDMI output
Digital input/output
• i 1920: 1,920 × 1,080 (1080p), 30 fps
• h 1280: 1,280 × 720 (720p), 30 fps
• f: 640 × 480 (VGA), 30 fps
• Y 640 × 480: 640 × 480, 70 fps
• Y 320 × 240: 320 × 240, 120 fps
• Y 320 × 112: 320 × 112, 200 fps
Note: i, h, and f movies are recorded with stereo sound.
Arabic, Bulgarian, Simplified Chinese, Traditional Chinese, Czech, Danish, Dutch, English, Farsi, Finnish,
French, German, Greek, Hebrew, Hungarian, Indonesian, Italian, Japanese, Kazakh, Korean, Latvian,
Lithuanian, Norwegian, Polish, Portuguese, Romanian, Russian, Serbian, Slovak, Spanish, Swedish,
Thai, Turkish, Ukrainian, Vietnamese
NTSC or PAL output with monaural sound
HDMI Mini Connector
USB 2.0 High-Speed; shares A/V OUT connector; MTP/PTP
Power supply/other
Power sources
• NP-50 rechargeable battery
• AC-5VX AC power adapter and CP-50 DC coupler (sold separately)
Battery life (approximate numBattery type
Approximate number of frames
ber of frames that can be taken
NP-50 (type supplied with camera)
270
with a fully-charged battery)
CIPA standard, measured in B (auto) mode using battery supplied with camera and SD memory card.
Appendix
Camera dimensions
Shooting weight
Camera weight
Operating conditions
Note: Number of shots that can be taken with battery varies with battery charge level and will decline
at low temperatures.
117.0 mm × 69.6 mm × 56.8 mm/4.6 in. × 2.7 in. × 2.2 in. (W × H × D)
Approx. 350 g/12.3 oz., including battery and memory card
Approx. 330 g/11.6 oz., excluding battery, accessories, and memory cards
• Temperature: 0 °C – +40 °C/+32 °F – +104 °F
• Humidity: 10% – 80% (no condensation)
123
Specifications
NP-50 rechargeable battery
Nominal voltage
DC 3.6 V
Nominal capacity
1000 mAh
Operating temperature
0 °C – +40 °C/+32 °F – +104 °F
Dimensions (W × H × D)
35.4 mm × 40.0 mm × 6.6 mm/1.3 in. × 1.5 in. × 0.2 in.
Weight
Approx. 18 g/0.6 oz.
BC-45W battery charger
Rated input
Input capacity
Rated output
Supported batteries
Charging time
Dimensions (W × H × D)
Weight
Operating temperature
100 V–240 V AC, 50/60 Hz
• 100 V: 8.0 VA
• 240 V: 12 VA
4.2 V DC, 550 mA
NP-50 rechargeable batteries
Approx. 150 minutes (+20 °C/+68 °F)
91 mm × 62 mm × 23 mm/3.5 in. × 2.4 in. × 0.9 in., excluding projections
Approx. 67 g/2.3 oz., excluding battery
0 °C – +40 °C/+32 °F – +104 °F
Weight and dimensions vary with the country or region of sale.
124
Specifications
Color Television Systems
NTSC (National Television System Committee) is a color television telecasting specification adopted mainly in
the U.S.A., Canada, and Japan. PAL (Phase Alternation by Line) is a color television system adopted mainly in
European countries and China.
Notices
• Specifications subject to change without notice; for the latest information, visit http://www.fujifilm.com/products/
digital_cameras/index.html. FUJIFILM shall not be held liable for damages resulting from errors in this manual.
• Although the monitor is manufactured using advanced high-precision technology, small bright points and
anomalous colors (particularly in the vicinity of text) may appear. This is normal for this type of monitor and
does not indicate a malfunction; images recorded with the camera are unaffected.
• Digital cameras may malfunction when exposed to strong radio interference (e.g., electric fields, static electricity, or line noise).
• Due to the type of lens used, some distortion may occur at the periphery of images. This is normal.
Appendix
125
Restrictions on Camera Settings
Shooting Mode and Camera Settings
The options available in each shooting mode are listed below.
E
Adv.
R S T U B i j r P
OFF
F
F
G
✔
✔
AUTO
N
B OFF
O
✔
✔
✔
P
N4
K
L
B ON
M
✔
✔
P
h
S /R
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
P
J
I
K
O
P
DRIVE
O
W
X
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔
✔ ✔
✔ ✔
Y
d
126
✔ ✔
✔ ✔
S
A
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔
✔
✔
✔ ✔ ✔
✔
✔
✔1 ✔ ✔1 ✔1 ✔1 ✔ ✔ ✔
✔
✔
✔
✔ ✔ ✔
✔
✔
✔1 ✔ ✔1 ✔1 ✔1 ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔
✔
✔ ✔ ✔
✔
✔ ✔ ✔
✔ ✔
✔ ✔ ✔
✔ ✔
✔ ✔ ✔
✔ ✔
✔ ✔ ✔
✔
✔ ✔ ✔
✔
✔ ✔ ✔
✔
✔ ✔ ✔
✔
✔ ✔ ✔
✔
✔ ✔ ✔ ✔ ✔ ✔
✔ ✔
✔ ✔ ✔ ✔ ✔
SP
M C D h Z M N O H p Q R s f U V W F
✔ ✔ ✔ ✔1
✔ ✔ ✔
✔
✔
✔
✔ ✔1
✔
✔
✔
✔1 ✔
✔
✔ ✔1
✔
✔
✔
✔1 ✔
✔ ✔ ✔ ✔
✔
✔
✔
✔ ✔
✔
✔ ✔
✔
✔ ✔
✔
✔
✔
✔
✔ ✔ ✔
✔ ✔ ✔ ✔
✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1
✔1 ✔1
✔
✔
✔
✔
✔
✔ ✔
✔ ✔1 ✔ ✔ ✔ ✔1
✔
✔
✔
✔
✔
✔ ✔
✔ ✔1 ✔ ✔ ✔ ✔1
✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔1
✔ ✔ ✔ ✔
✔
✔ ✔ ✔ ✔
✔1 ✔
✔ ✔ ✔ ✔1
✔ ✔ ✔ ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
Restrictions on Camera Settings
E
Adv.
R S T U B i j r P
AUTO
AUTO (3200)
AUTO (1600)
AUTO (800)
AUTO (400)
✔1
6400
5000
4000
3200
2500
2000
1600
1250
1000
800
640
500
400
320
250
200
100
p
q
s
F6
t
x
SP
M C D h Z M N O H p Q R s f U V W F
✔
✔
✔
✔
✔
✔
✔
✔
✔1 ✔
✔
✔
✔
✔1 ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔1 ✔1 ✔1 ✔1 ✔
✔
✔
✔
✔
✔
✔
✔ ✔1 ✔1 ✔1 ✔1 ✔
✔ ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1
✔
✔
✔
✔ ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1
✔
Appendix
o
5
A
✔1 ✔1 ✔1
✔
✔
✔ ✔
✔ ✔
12800
N
S
127
Restrictions on Camera Settings
E
Adv.
R S T U B i j r P
AF-C
AF-S
MF 7
AUTO
O
O
P
Q
T
AUTO
A
✔1 ✔
✔
✔
✔
✔
✔
✔ ✔
✔ ✔
✔ ✔
✔1
✔1
B
U
C
D
M
c
d
e
b
P
e
d
f
f
d
f
H
r
s
h
128
✔ ✔
✔
✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
S
A
SP
M C D h Z M N O H p Q R s f U V W F
✔ ✔
✔ ✔
✔ ✔ ✔1 ✔1 ✔1 ✔ ✔
✔ ✔
✔ ✔
✔
✔ ✔
✔
✔
✔
✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔
✔
✔ ✔
✔
✔ ✔
✔ ✔1 ✔ ✔
✔ ✔ ✔ ✔
✔1 ✔1 ✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔1 ✔1
✔1 ✔
✔
✔
✔
✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔
✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔
✔
✔
Restrictions on Camera Settings
E
Adv.
R S T U B i j r P
R
Z
b
n
F ((F
F mode)
i 1920
h 1280
W
f
k 640×480
k 320×240
k 320×112
I
g
K
L
l
L
M
m
OFF
C
j
A
SP
M C D h Z M N O H p Q R s f U V W F
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔
✔2 ✔ ✔ ✔ ✔ ✔ ✔ ✔3 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔2 ✔3 ✔3 ✔ ✔ ✔3 ✔ ✔ ✔ ✔3 ✔ ✔3 ✔3 ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔
✔ ✔ ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔
✔ ✔ ✔ ✔
✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔ ✔
✔1 ✔ ✔ ✔ ✔ ✔ ✔
✔
✔
✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔
✔
✔
✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔1 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔1 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔3 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔3 ✔3 ✔ ✔ ✔3 ✔3 ✔ ✔ ✔ ✔3 ✔3 ✔ ✔
✔3 ✔3 ✔3 ✔3 ✔ ✔3 ✔3 ✔3 ✔ ✔ ✔ ✔ ✔3 ✔3 ✔3 ✔3 ✔3 ✔3 ✔3 ✔3 ✔3 ✔3 ✔3 ✔3 ✔3 ✔3 ✔3 ✔3
Optimized for selected shooting mode.
ON selected automatically.
OFF selected automatically.
Flash disabled in all shooting modes if lowered.
o (MULTI) selected automatically when Intelligent Face Detection is on.
Camera focuses on faces when Intelligent Face Detection is on.
Intelligent Face Detection turns off automatically in manual focus mode.
Appendix
1
2
3
4
5
6
7
S
129
Memo
130
Memo
131
Memo
132
Memo
133
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN
http://www.fujifilm.com/products/digital_cameras/index.html
Please contact your local distributor for repairs and technical support. (see Worldwide
Network list)
Printed in