FujiFilm Zoom 60 Digital Camera User Manual

ENGLISH
•
•
•
•
•
•
Fujinon 35-60mm Auto Focus Zoom Lens
Automatic Flash
Easy Film Loading
Automatic Film Rewind
Full Information LED Operating Display
Date/Time Imprinting
(on the DISCOVERY S600 ZOOM DATE /
ZOOM DATE 60 only)
• Red-Eye Reduction
,
OWNER S MANUAL
CONTENTS
FEATURES ............................................................................... 2
PART NAMES ........................................................................... 3
1. PRELIMINARY STEPS
ATTACHING THE STRAP ........................................................ 7
LOADING THE BATTERIES .................................................... 8
TURNING ON YOUR CAMERA ............................................. 10
CHECKING YOUR BATTERY ................................................ 11
SETTING THE DATE
(YEAR-MONTH-DAY/HOUR-MINUTE)
(on the DISCOVERY S600 ZOOM DATE/
ZOOM DATE 60 only) ............................................................. 12
SELECTING THE DATE MODE
(on the DISCOVERY S600 ZOOM DATE/
ZOOM DATE 60 only) ............................................................. 14
2. USING YOUR CAMERA
LOADING THE CAMERA ....................................................... 15
USING YOUR FINDER ........................................................... 19
USING YOUR CAMERA ......................................................... 20
USING THE AUTO-FOCUS LOCK ........................................ 25
UNLOADING THE FILM OR REMOVING FILM IN MID-ROLL ... 27
2
3. ADVANCED TECHNIQUES
SELECTING THE EXPOSURE MODE .................................. 31
USING THE SELF-TIMER ...................................................... 35
TROUBLE SHOOTING ........................................................... 37
COMMON SENSE CAMERA CARE ...................................... 40
SPECIFICATIONS .................................................................. 41
FEATURES
•
•
•
•
•
•
Fujinon 35-60mm Auto Focus Zoom Lens
Automatic Flash
Easy Film Loading
Automatic Film Rewind
Full Information LED Operating Display
Date/Time Imprinting
(on the DISCOVERY S600 ZOOM DATE/ZOOM DATE 60 only)
• Red-Eye Reduction
The “CE” mark certifies that this product satisfies the
requirements of the EU (European Union) regarding
safety, public health, environment and consumer
protection.(“CE” is the abbreviation of Conformité
Européenne.)
This product is in conformity with Directive 89/336/EEC.
PART NAMES
7
1(→p.5)
8(→p.31, 35)
2(→p.10)
3(→p.21)
9(→p.29)
0(→p.32, 36)
4(→p.22)
A(→p.23, 31)
1
2
3
4
5
6
7
8
9
0
Liquid Crystal Display
Power Button
Zoom Button
Shutter Release Button
Strap Lug
AF (Autofocus) Window
Viewfinder Window
MODE Button
Mid-Roll Rewind Button
Red-eye Reduction/SelfTimer Lamp
A Flash
B AE Light Sensor
C Fujinon Lens/ Lens Cover
B
5(→p.7)
6
C(→p.10)
3
D(→p.19)
I
J(→p.16, 28)
E(→p.22)
F
K
L(→p.16)
M(→p.8)
G(→p.16, 28)
H(→p.17)
4
N
D
E
F
G
H
I
J
K
L
M
Viewfinder Eye-piece
AF/Flash Ready Lamp
Film Take-up Spool
Camera Back Lock
Film Leader Mark
Film Chamber
Camera Back
Film Pressure Plate
Film Confirmation Window
Battery Compar tment
Cover
N Tripod Socket
Liquid Crystal Display
∗
O(→p.32)
R(→p.34, 22)
P(→p.18)
S(→p.18)
Q(→p.11)
T(→p.35)
O Red-eye Reduction Flash
Mode
P Film Display
Q Battery Status
R
Fill-in Flash Mode/
Flash off Mode/
Flash Charging
S Exposure Counter
T Self-Timer Mode
The diagram shows all crystal displays in the “on” state.
5
Date/Time Display
(on the DISCOVERY S600 ZOOM DATE/ZOOM DATE 60 only)
U(→p.12, 14)
V(→p.14)
W(→p.12, 14)
X(→p.12)
Y(→p.12, 14)
∗
6
The diagram shows all crystal displays in the “on” state.
Z(→p.13)
U
V
W
X
Y
Z
Month Display
Date/Time Imprinting
Date Display
SELECT Button
MODE Button
SET Button
1
1. PRELIMINARY STEPS
ATTACHING THE STRAP
Slip the thin cord on the carrying strap through the strap lug on the side of the
camera leaving a loop. Slide the thick part of the strap through this loop and pull
tight. Take up any slack to make sure the strap is securely attached to the camera.
Do not use a strap made for cellular phones or similar electronic products. These straps are
usually too light to hold your camera securely. Use straps designed for cameras for safety.
2
A
A : Button Push Projection
Use the button push projection to push the DATE-MODE, SELECT, SET button and
button.
the
7
LOADING THE BATTERIES
1
Make sure you have the correct batteries for your camera and that they are fresh.
Your camera uses two alkaline batteries (Size AA/LR6) for reliable service. Do not try
to use other types or sizes of batteries and do not mix an old battery with a new one.
It is best to buy two batteries of the same brand at the same time.
To load batteries. . .
Open the battery compartment cover by pressing your finger against the finger rest and sliding the cover in the direction of the arrow.
1 It is important to insert the batteries correctly. Follow the instructions in the diagram on
2
2
1
8
the insider of the battery cover. Pay particular attention to the position of the , and poles of the batteries. If the batteries are no inserted correctly, the camera will not
operate.
2 Once the batteries are correctly inserted, close the battery compartment cover by snapping it into place. When the cover is closed properly, it fits flush against the bottom of the
camera. If you have trouble, check the placement of the batteries to make sure they are
properly seated in the battery compartment.
∗
∗
∗
∗
∗
∗
∗
∗
Do not apply excessive force when opening the battery cover.
Do not load film before insertng the battery into the camera.
Make sure that the new batteries are both the same brand and type.
Do not use Ni-Cd batteries.
Two alkaline batteries should be sufficient for approximately 360 exposures (based on our test
conditions).
When traveling, take extra batteries to provide power for extra exposures, particularly important
if you visit areas where fresh batteries may be difficult to obtain.
Check the battery capacity symbol before using your camera. (→p.11)
At low temperatures, battery capacity is reduced. Warm the batteries, e.g. in your pocket, before
using them.
9
TURNING ON YOUR CAMERA
To prepare to use your camera, first press the power supply button to turn on the
power. Pressing the button once more turns the power off.
☞ When you turn your camera on, the lens cover will open and the initial display will appear in the
LCD panel.
∗
10
When you are finished using your camera, turn the power off to conserve your battery. If the
power supply is left on for more than 5 minutes without the camera being used, the camera will
automatically turn itself off. If the POWER button is pressed, the power is turned back on again.
Before you turn the camera on, make sure that the lens is not blocked to avoid any interference
with the lens extending into its picture taking position.
CHECKING YOUR BATTERY
1
To determine the condition of the battery in your camera, turn it on and check the
battery capacity indicator on the LCD panel.
2
1on : Battery capacity is OK.
2on : Battery capacity is low. Replace with a new battery.
3blink : Shutter cannot be released because battery is exhausted. Replace with a
fresh battery.
3
∗
Check the battery capacity before you start to use your camera.
11
SETTING THE DATE
(YEAR-MONTH-DAY/HOUR-MINUTE)
1
(on the DISCOVERY S600 ZOOM DATE/ZOOM DATE 60 only)
Setting the Date
1
2
1 Press the MODE button and “
2 Press the SELECT button.
” to display the year, month and day.
☞ The numerals will blink and the camera will enter the date setting mode.
∗
The numeral under the “
” in the display area indicates the month.
Setting the Time
1 Press the MODE button to display the hour and minute.
2 Press the SELECT button.
☞ The numerals will blink and the camera will enter the time setting mode.
1
2
∗
12
The date cannot be changed at this stage.
The date changes along with the time. To display both correctly, set the date and time together.
1 Press the SET button to change the blinking setting.
2 Press the SELECT button to select the next part of the date/time information.
2
You can set:
Year : ’98 to ’49 (1998 to 2049)
Month : 1 to 12 Day : 1 to 31
Time : 0 to 23
hours; 00 to 59 minutes
●
2
3
1
Once the date and time are set, press the SELECT button and setting will cease.
☞ To set the time (hour or minute) by the radio, set the correct time using the time correction
mode, and press in the SELECT button when the time signal indicates zero.
13
SELECTING THE DATE MODE
(on the DISCOVERY S600 ZOOM DATE/ZOOM DATE 60 only)
The date and time (year-month-day/ hour-minute) will be imprinted at the lower right
of the photograph.
∗
The date display printed on the front of the picture may not be clearly visible against a dark
background.
Y : Year M : Month D : Day T : Time
YMD
DT
MDY
DMY
14
With each press of the MODE button, the date mode changes as in the illustration.
_
☞ The date and time will be printed based on the mode you select.
∗
∗
∗
If “
” is showing in the upper right of the display area, the date will be imprinted on the
photograph.
The numeral under the “
” in the display area indicates the month.
If “- - - - - -” is chosen, no date will appear on the photograph.
2. USING YOUR CAMERA
A
LOADING THE CAMERA
Your camera uses standard 35mm film available anywhere. Almost all 35mm films
will have a DX coding symbol on the film box and on the cassette itself. Use only
35mm films with ISO rating of 100, 200 or 400. Information you will see includes:
B
C
A : Number of Exposures
B : DX Code symbol
C : Film Speed (sensitivity to light or ISO rating)
• If non-DX coded film is used, the camera’s automatic exposure system automatically sets itself
to ISO 100.
• Always load and remove film from your camera away from direct sunlight.
15
1
Check the film check window to make sure no film is loaded into the camera.
∗
2
Never open the camera back while film is in your camera.
1 To load the film, slide camera back lock in the direction of the arrow as shown in
the picture at left.
2 Open the back as shown.
2
1
16
∗
Never apply excessive force when opening or closing the camera back.
Insert batteries before loading film.
3
2
1 Hold the film at an angle and place it in the camera.
2 Press the film until you hear a clicking sound. This indicates the film cassette is
seated properly.
1
4
A : FILM TIP mark
While holding the film cassette in place, gently pull the end of the film leader out as
far as the FILM TIP mark in the camera.
∗
∗
∗
Hold the film cassette down so that it does not pop out of the film compartment.
Make sure the end of the film is correctly threaded onto the spool.
If you should pull the film out too far, remove the film cassette and rotate the longer end of the
spool slowly to rewind some of the exposed film and adjust the leader to the correct length to
reach the FILM TIP mark. Be careful not to rewind the leader completely into the cassette.
A
17
5
Close the camera back.
☞ The film advances automatically.
☞“
” and “ ” are displayed.
∗
6
18
The type, number of exposures, and speed of the film that has been loaded may be checked
with the film check window.
Check that the exposure counter (“ ”) and “
If “ ” and “
” appear in the LCD.
” are not displayed in the LCD, the film is not advancing. Load the film again.
USING YOUR FINDER
The large viewfinder of your FUJIFILM camera makes it easier to take better, more
interesting pictures. The finder consists of two parts:
A : Framing Area
A
Compose your picture within these framelines.
B : AF (Autofocus) frame
Position this frame over the main subject being photographed to ensure sharp.
B
19
1
USING YOUR CAMERA
Turn the camera on and hold it firmly using both hands as shown in the illustration.
When taking vertical pictures, hold the camera with the flash unit at the top.
Before taking important, once-in-a-lifetime pictures such as weddings or special events, take a
few test shots to make sure your camera is functioning correctly. If you purchased your camera
before going on a trip, shoot a roll or two to familiarize yourself with the operation of the camera.
And don’t forget to get an extra set of batteries. You should also keep this instruction book with
you for handy reference.
2
20
Make sure that nothing is in front of the lens, the flash, the autofocus windows or the
automatic exposure light sensor.
3
To use the zoom lens, press the T (telephoto) mark until you see the composition
you want in the finder. Pressing the W (wide angle) mark will set the lens at the
shorter focal lengths to obtain wide-angle coverage.
∗
∗
4
The focusing range for sharp pictures is from 1.0 m (3.3 ft.) to infinity at wide angle, 1.6 m (5.2
ft.) to infinity at telephoto.
If you use flash for taking pictures in low light, check with the flash section to determine the
operating range for correct exposure. The flash will not provide correct exposures beyond its
normal operating range. (→p.23)
Aim at your subject so that it is covered by the whole AF frame.
21
5
Press down the shutter release halfway.
☞ Check that the AF/flash ready lamp (green) lights up.
∗
6
When the flash ready lamp is blinking and “ ” blinks on the LCD, the flash is charging. The
shutter cannot be released until the flash is ready.
Press the shutter button down completely.
☞ The flash fires when photographing under low light conditions.
☞ The film advances to the next frame.
☞ The number shown in the exposure counter will increase by 1 with each frame exposed. This
provides a check on the number of pictures taken on that roll.
22
The operating range of the film (flash distance) will vary depending upon the film’s sensitivity (ISO speed). When using flash,
keep your subject within the range of the effective flash illumination as indicated in the chart below.
Effective flash range
Film speed
ISO 100
ISO 400
Wide angle (35 mm)
1.0 – 2.8 m
3.3 – 9.2 ft.
1.0 – 5.5 m
3.3 – 18.0 ft.
Telephoto (60 mm)
1.6 – 2.0 m
5.2 – 6.6 ft.
1.6 – 3.4 m
5.2 – 11.2 ft.
(Using color negative film)
23
Under certain unusual conditions, the camera’s autofocus system may not be able to function accurately. At these times, you
should use the “Autofocus Lock” setting (→p.25). Conditions which may require these settings include:
●
●
●
●
●
24
A bright light source with the picture area such as the sun near your subject or a strong reflection from water or the windshield of a vehicle;
A mirror or other strongly reflective surface near the center of your picture;
Photographing black or very dark light absorbing subjects such as hair;
Presence of flames, smoke or gaseous substances;
Photographing through glass.
1
2
USING THE AUTO-FOCUS LOCK
In the composition shown at left, the AF frame is off the subject (in this case, the
people). In this case the lens will not focus on the subject.
Move the camera to position the AF frame over the subject.
25
3
4
With the AF frame positioned over the subject, press down the shutter release button halfway to set the auto-focus lock.
☞ Check that the AF/flash ready lamp (green) lights up.
While holding the shutter release button halfway down to keep the Auto-Focus lock
on, move the camera back to the original position to recompose your picture, then
press the shutter release button all the way down.
∗
26
The Auto-Focus lock operation can be repeated any number of times before the shutter trips.
1
UNLOADING THE FILM OR REMOVING FILM IN MID-ROLL
To Unload the Film
When the last frame in the film has been exposed, the film automatically rewinds
into the film cassette which can then be removed for processing.
☞ While the film is being rewound, the lens cover automatically closes and “
∗
2
” is displayed.
Sometimes more photographs can be taken than the stated number of exposures, but the final
frame may not be printed.
When the motor stops, check that “ ” and “ ” are blinking on the display.
Do not open the camera back before “
exposed to the light.
” and “ ” are blinking on the display. The film may be
27
3
1 Slide the camera back lock in the direction indicated by the arrow.
2 Open the camera back in the direction indicated by the arrow.
2
1
4
28
∗
Do not apply unnecessary force to the camera back.
Remove the film.
Removing film in mid-roll
Press the
button using the special button pushing projection on the strap, etc.
☞ While the film is being rewound, the lens cover automatically closes and “
” is displayed.
☞ When the film has been fully rewound, “ ” and “ ” blink on the display. Check that the motor
has stopped and that “
∗
Do not press the
” and “ ” are blinking on the display before removing the film.
button with any object that tapers to a sharp point.
Film cannot be reused once it has been rewound. Do not press the
removing the film for developing.
button except when
29
◆ Do not open the camera back while there is a film in mid-roll in the camera.
☞ If the camera back is opened while there is a film in mid-roll in the camera, the film may be
exposed to the light.
☞ The exposure counter is reset to “ ”.
If the camera back is opened by mistake:
1 Close the camera back without removing the film.
2 While covering the lens with your hand, press the shutter a few times to feed
some unexposed film.
3 The remaining frames can be used.
∗
30
Since the exposure counter is reset to “ ” when the camera back is opened, the correct film
count is not displayed. However, you can continue to make exposures until the roll is finished at
which time you will feel a resistance in the film transport. At this point, rewind the film into the
cassette and remove it from the camera. DO NOT TRY TO ADVANCE THE FILM ONCE THIS
RESISTANCE IS FELT.
3. ADVANCED TECHNIQUES
SELECTING THE EXPOSURE MODE
Turn on the camera and each push of the MODE button changes the exposure
mode in the following order:
☞
→
(
(
(
(
) Automatic flash for low light situations
) Red-eye reduction flash for more pleasing pictures of people
) Back light compensation flash mode
) Flash-off mode for natural light pictures
☞
→
→
→
: Self-timer Mode (→p.35)
• The selected exposure mode is maintained even after the photography has been completed.
• The red-eye, back light and flash-off modes are automatically cancelled and the automatic flash
mode is set when the power is turned off.
31
(
: no display) Automatic flash at low brightness mode
Used for general photography.
The flash lamp fires automatically when the brightness of the subject is lower than
the predetermined level.
(
) Red-eye reduction flash mode
Reduce red-eye.
The red-eye reduction lamp turns on for about 0.7 second, then the camera takes a
picture when the flash fires.
32
Once the red-eye reduction lamp has come on, the flash ready lamp will remain lit until the
picture is taken. Do not move the camera while the flash ready lamp is lit.
Dealing with red-eye
When you photograph a person in dim light using flash, the pupil of the eye will sometimes
appear red. Under low light, the pupils of the eye dilate for better vision. Red-eye is caused
by light from the flash entering the dilated pupils and being reflected back to the lens. Redeye reduction causes a preliminary flash to fire before the actual picture is taken. This
causes the pupil to contract, reducing this reflection. When the actual flash exposure is
made, the degree of reflection is minimized, thus reducing red-eye.
When using red-eye reduction mode
● Ask your subject to look directly into the camera.
● Approach as closely as possible to make your exposure.
33
(
) Back light compensation flash mode
Use this mode to avoid deep shadows when photographing against the light such as a person
standing in front of a window or under a tree with a very bright background. This produces more
natural looking flash photographs.
Flash pictures taken even in a bright place.
(
) Flash off mode
Used when taking pictures with normal room lighting being utilized, or taking pictures of remote
subjects beyond the range of the flash, for example, in a theater or a stadium.
The flash stops firing.
34
∗
When taking pictures under low light, use a tripod whenever possible to avoid unsharp pictures
resulting from camera shake.
1
USING THE SELF-TIMER
Push the MODE button with the power on to display “
”.
The self-timer mode is maintained even after the photography has been completed. It is automatically cancelled when the power is turned off.
2
1 Aim at the subject in the center of the framing area.
2 Press down the shutter release button.
☞ The camera focuses on the subject, and then the self-timer starts.
When pressing the shutter release button, do not stand in front of the camera. This may cause a
focusing error or underexposure.
35
3
The shutter will operate after the self-timer lamp has completed a 10-second series
of sequences-a sequence of slow blinking (approximately 7 seconds) followed by
fast blinking (approximately 1.5 seconds) and a final lighting up (approximately 1.5
seconds).
When you desire to cancel the self-timer mode after it has been started, press the shutter release button once more or turn the power off.
36
TROUBLE SHOOTING
During operation
Problems
Possible Causes
The shutter release
won’t trip.
1 “
” symbol is blinking.
2 Power switch is not on.
3 Are “ ” and “ ” blinking on the display?
1 Replace the battery with a new one.
2 Press the POWER button.
3 Remove the film, and load an unexposed roll.
11
10
15
The film rewound during
photographing.
● Did you operate the rewind button in
● Be sure not to move the rewind button while film
29
After loading the film and
closing the back cover,
the exposure counter
does not advance.
1 Did you pull the end of the film out to
the FILM TIP mark when loading the
film?
2 Did you insert the battery after loading the film?
1 Pull the end of the film out to the FILM TIP mark
and correctly load the film.
15
2 A picture can not be taken by pressing the shutter release button in that condition. Open the camera back a little and close it again.
15
The camera back will
not close.
● Is the film cassette in positioned prop-
● After straightening the film cassette, close the
17
the middle of the film?
erly?
Solutions
Page
is loaded in the camera.
camera back.
37
Printed pictures
Problems
Picture is not sharp.
Possible Causes
Solutions
Page
1 Was your finger on the AF windows
when shooting?
20
5 Was the subject too close (less than
1.0 m/3.3 ft.)?
1 When shooting a picture, hold your camera correctly so that your finger is not on the AF windows.
2 Compose the picture in the AF frame and shoot,
or shoot using AF Lock.
3 Clean the lens.
4 Hold the camera firmly and press the shutter release button gently. Use a tripod for slow shutter
speeds.
5 Take picture of a subject at a distance greater than
W: 1.0 m (3.3 ft.), T: 1.6 m (5.2 ft.).
1 Subject was too far from the camera
for flash photography in a dark place.
2 Was your finger over the flash?
3 Was the subject backlit from being
taken next to a window, etc.?
1 Shoot within specified coverage distance of electronic flash.
2 Do not cover the flash with your finger.
3 Turn on the back light compensation flash mode
and press the shutter release button.
23
2 Did you aim the subject properly?
3 Is the lens dirty?
4 Is the camera moving?
Picture is too dark.
38
25
40
20
21
20
34
Printed pictures
Problems
Possible Causes
Printed date/time is incorrect.
(on the DISCOVERY
S600 ZOOM DATE/
ZOOM DATE 60 only)
● You didn’t set correct date and time
The date is not printed
on the front.
(on the DISCOVERY
S600 ZOOM DATE/
ZOOM DATE 60 only)
1 Wasn’t “- - - - - -” selected before taking pictures?
2 Is there something light-colored
(white, yellow, orange) where the date
appears?
Solutions
Page
● Set date and time after replacing battery.
12
1 Select a date mode other than “- - - - - -” before
taking pictures.
2 Try to arrange that there is nothing light-colored
where the date appears.
14
after replacing battery.
14
39
COMMON SENSE CAMERA CARE
1
Although your camera is designed for many years of service,
it is a precision instrument and requires thoughtful handling.
In particular, avoid exposing it to shock, moisture or physical
abuse such as dropping it on the floor.
5
It is recommended that undeveloped film and cameras containing film be carried as hand luggage when flying. If included
in checked-in baggage, X-ray inspections may cause overprinting or other effects.
1 If you use your camera at the beach or in a light rain, protect it from moisture. Do not let your camera get wet. Be
particularly careful to avoid sand and salt spray at the
beach.
6
Remove soil and dust from the lens, the AF window and the
finder with an air blower and by wiping lightly with a piece of
soft cloth. If that is not enough, wipe off gently with Lens Cleaning Paper, moistened slightly with Lens Cleaning Liquid. Do
not use organic solvents such as alcohol and benzene.
7
Dust and debris in the film compartment can scratch the film.
Use a blower brush to clean it.
8
9
Load and remove film away from direct sunlight.
0
Since the performance of the battery will drop in cold weather,
warm the battery by placing it inside your garments, etc. before use. The performance of a battery whose performance
has temporarily dropped can be restored by returning the battery to normal temperature.
2 Dropping your camera or letting it strike a hard surface
could result in damage even though the camera was in a
case. Never subject the camera to vibration such as in the
trunk of a car. Never keep your camera in the trunk or the
glove compartment of a car: the heat build-up can damage it.
40
2
Your camera is computer-controlled so it seldom, if ever, will
operate erroneously. If you should experience erroneous operation, remove the battery and then reload it.
3
If you will not be using your camera for some time, store it
where it will be safe from heat, moisture, dust and harmful
gases such as napthalene (moth balls and moth flakes).
4
Never store the camera in a closed automobile for an extended
period.
The operating temperature range of the camera is from –5°C
to +40°C.
With a few common sense precautions, your camera will give you
years of faithful service, great pleasure and wonderful pictures.
SPECIFICATIONS
• Film
• Film Speed Setting
135 (35 mm) DX roll film
• Picture Size
24 mm × 36 mm
• Lens
Fujinon lens, 2 components, 4 elements, f=35 – 60 mm 1:6.3 –
1:10.2
• Viewfinder
Inverted Galilean finder, 0.5 – 0.8 × magnification, with AF frame
• Focusing
Active type auto focus, Wideangle:1.0 m (3.3 ft.) –
,
Telephoto:1.6 m (5.2 ft.) –
• Shutter Release
Programmed electronic shutter release, 1/3 – 1/300 sec. shutter
speeds
• Exposure Control
Automatic
Interlocking range (ISO 100), EV (wide angle): 11 (*7) – 16, EV
(telephoto): 12 (*8) – 15
(* = values for the flash off mode)
Automatic (DX roll film) for speeds from ISO 100/200, 400
• Film Loading
Automatic
• Film Advance
Automatic (motorized), film wind and rewind system, provision
for mid-roll rewinding
• Flash
Built-in flash, 6 seconds recycle time, automatic flash at low
brightness mode, red-eye reduction flash mode, fill-in flash mode,
flash off mode
• Self-Timer
Electronically controlled, approximately 10 second delay, can
be stopped mid-run, self-timer on lamp
• Liquid Crystal Display
Exposure counter, exposure mode index, self-timer mode sign,
battery capacity sign, film display, flash charging sign.
Date sign (on the DISCOVERY S600 ZOOM DATE/ZOOM DATE
60 only)
∞
∞
41
• Power Supply
Two alkaline batteries (LR6/AA size)
• Others
Tripod socket
• Dimensions & Weight
115.5 × 69.5 × 54.5 mm/4.5 × 2.7 × 2.1 in. (main unit),
205 g/7.2 oz. (without battery)
∗ Specifications are subject to change without notice.
42
Memo
....................................................................................................................................................................................................................
....................................................................................................................................................................................................................
....................................................................................................................................................................................................................
....................................................................................................................................................................................................................
....................................................................................................................................................................................................................
....................................................................................................................................................................................................................
....................................................................................................................................................................................................................
....................................................................................................................................................................................................................
....................................................................................................................................................................................................................
....................................................................................................................................................................................................................
....................................................................................................................................................................................................................
26-30, Nishiazabu 2-chome, Minato- ku, Tokyo 106-8620, Japan.
<FUJIFILM ABROAD>
In North America
FUJI PHOTO FILM U.S.A., INC.
555 Taxter Road, Elmsford, N.Y. 10523, U.S.A.
FUJI PHOTO FILM CANADA INC.
275 Britannia Road East, Mississauga, Ontario , L4Z 2E7, Canada
FUJI PHOTO FILM HAWAII, INC.
1650 Kalakaua Avenue, Honolulu, Hawaii 96826, U.S.A.
In Europe
FUJI PHOTO FILM (EUROPE) G.m.b.H.
Heesenstrasse 31, 40549 Dusseldorf, Germany
FUJI PHOTO FILM (U.K.) LTD.
Fuji Film House, 125 Finchley Road, Swiss Cottage, London NW3 6JH, England
FUJI FILM ESPAÑA, S.A.
Aragon, 180, 08011-Barcelona, Spain
In South America
FUJI PHOTO FILM DO BRAZIL LTDA.
Avenida Vereador Jose Diniz No. 3.400, Campo Belo- CEP 04.604
Cx. Postal 9.959., Sao Paulo-SP, Brazil
In Asia
FUJI PHOTO FILM CO., LTD., HONG KONG OFFICE
Room 916, Sun Plaza, 28 Canton Road, Tsim Sha Tsui, Kowloon, Hong Kong
FUJI PHOTO FILM (SINGAPORE) PTE. LTD.
10 New Industrial Road, Singapore 536201
FUJI PHOTO FILM (THAILAND) LTD.
S.P. Building, 8th Floor, 388 Phaholyothin Road, Bangkok 10400, Thailand
FUJI PHOTO FILM (MALAYSIA) SDN. BHD.
Letter Box 3, 3rd Floor Office Block 1, Crystal Plaza Lot 4, Jalan 51A/223, 46100 Petaling Jaya Selangor Darul Ehsan Malaysia
FUJI PHOTO FILM CO., LTD., TAIPEI OFFICE
Rm. 601, Hung Chong Bldg., No.38, Sec. 6, Min Chuan E. Road, Taipei 11412, Taiwan, Republic of China
FUJI PHOTO FILM CO., LTD., SEOUL OFFICE
Samduck Bldg. 6F., 144-1, Samsung-Dong, Kang Nam-ku, Seoul 135-090, Korea
FUJI PHOTO FILM CO., LTD., BEIJING REPRESENTATIVE OFFICE
Beijing Fortune Bldg. No. 817, 5, Dong Sanhuan Bei-lu, Chaoyang District, Beijing, China 100004
FUJI PHOTO FILM CO., LTD., HO CHI MINH OFFICE
29-31 Ton That Thiep St., Q.I Ho Chi Minh City, Vietnam
FUJI PHOTO FILM CO., LTD., NEW DELHI OFFICE
Le Meridian Commercial Tower 8F Janpath, New Delhi 110001, India
In Oceania
FUJI PHOTO FILM CO., LTD., SYDNEY REPRESENTATIVE OFFICE
c/o Hanimex Pty. Limited, Old Pittwater Road, Brookvale, N.S.W. 2100, Australia
In Middle East
FUJI PHOTO FILM CO., LTD., DUBAI OFFICE
No. 4G-17, L.O.B. No. 4, P.O. BOX 17212, Jebel Ali, Dubai, U.A.E.
Printed in China
FGS-002112-P-01