User`s manual | Fujitsu 15C Scanner User Manual

Scanpartner 15C
Image Scanner
User's Manual
Version 1.0
(Doc. No. 250-0062-0)
Table of Contents
1. INTRODUCTION .......................................................................................... 1-1
2. INSTALLATION AND CONNECTIONS .................................................. 2-1
2.1 SHIPPING BRACKET .............................................................................................................. 2-1
2.1.1 Removing the Shipping Bracket (refer to figures 2-1 and 2-2) ........................... 2-1
2.1.2 Refitting the Shipping Bracket: ............................................................................. 2-3
2.2 SCSI INTERFACE DEVICE ID ................................................................................................ 2-3
2.3 ADF PAPER CHUTE (FIGURE 2-4)........................................................................................ 2-5
2.4 ADF OUTPUT TRAY (FIGURE 2-5) ....................................................................................... 2-6
2.5 DOCUMENT LOADING ......................................................................................................... 2-7
2.6 ADF SCANNING.................................................................................................................. 2-8
2.7 CONNECTING THE CABLE .................................................................................................... 2-9
3. MAINTENANCE............................................................................................ 3-1
3.1 CLEANING THE ADF ........................................................................................................... 3-1
3.2 CLEANING THE GLASS ......................................................................................................... 3-3
4. TROUBLESHOOTING ................................................................................. 4-1
4.1 QUESTION AND ANSWER ..................................................................................................... 4-1
4.2 PAPER JAM IN THE ADF....................................................................................................... 4-3
5. SPECIFICATIONS ......................................................................................... 5-1
5.1 SCANPARTNER 15C SPECIFICATIONS ................................................................................... 5-2
ii
1.
INTRODUCTION
Congratulations on your purchase of Fujitsu Scanpartner 15C Scanner.
Before you install and operate the new Scanner, please take a few minutes to
read through this manual. It provides you with the proper instructions on
how to unpack, install, operate and maintain the Scanner.
Figure 1-1 shows how the Scanner is packed. You can check all items
against your “checklist”, included with your Scanner.
1-1
Output Paper Rack
Figure 1-1 Scanner packing
1-2
2. INSTALLATION AND CONNECTIONS
Please unpack the Scanner carefully, and check the contents against the checklist. If
any items are missing or damaged, please contact your authorized local dealer
immediately.
Precautions
❖
Keep the Scanner out of direct sunlight. Direct exposure to the sun or excessive
heat may cause damage to the unit.
❖
Do not install the Scanner in a humid or dusty place.
❖
Be sure to use the proper AC power source.
❖
Place the Scanner securely on an even, flat surface. Tilted or uneven surfaces may
cause mechanical or paper-feeding problems.
❖
Retain the Scanner box and packing materials for shipping purposes.
2.1 Shipping Bracket
The Scanner has a bracket that locks the carrier mechanism for transportation
purposes. This bracket must be put into the use position before using the Scanner.
If the power is turned on before the bracket has been removed the PAPER JAM light
will turn on. Before proceeding, turn the power off, disconnect all cables and follow
the instructions below to remove the shipping bracket.
2.1.1 Removing the Shipping Bracket (refer to figures 2-1 and 2-2)
i).
Carefully place the Scanner in an upright position on its front.
ii).
Using a suitable screwdriver, remove the screw and pull out the shipping
bracket.
iii).
Put the shipping bracket into the use positions with the short side extending
into the Scanner base and secure it with the screw.
iv).
Carefully place the Scanner back into its normal position.
2-1
Figure 2-1 Removing the Shipping Bracket
Figure 2-2 Securing the Shipping Bracket
2-2
2.1.2 Refitting the Shipping Bracket:
Whenever you need to move the Scanner to a new location it is advisable to
refit the shipping bracket to avoid causing damage to the Scanners’ internal
mechanism. Please follow the instructions below to refit the shipping bracket.
i).
Turn off the Scanner power at the power on/off switch.
ii).
Open the document cover.
iii). Turn off the Scanner.
Note: For steps (iv) to (vi) please refer to figure 2-1 and 2-2
iv). Carefully place the Scanner in an upright position on its front side.
v).
Use a suitable screwdriver to remove the screw holding the shipping
bracket in the use position.
vi). Put the shipping bracket into the shipping position, with the long side
extending into the Scanner base. Secure it with the screw.
vii). Carefully place the Scanner back into its normal position.
2.2 SCSI Interface Device ID
When you have several devices on a SCSI chain, you may need to adjust
the SCSI ID selector setting located on the back of the Scanner. This setting assigns a
specific "device ID" to the Scanner. If the assignment conflicts with an existing SCSI
device, please select a new ID. (See Figure 2-3)
Note: The factory setting for Scanner is ID 6. Usually, ID 0 is assigned to an internal
hard disk drive, and ID 7, to SCSI adapter or host. ID 8 and 9 are not in actual
use.
Using a suitable tool, turn the selector switch until the arrow points to the desired ID
number.
2-3
SCSI ID Selector
Figure 2-3 Adjusting the SCSI ID setting.
2-4
2.3 ADF Paper Chute (Figure 2-4)
i).
Raise the right side of the paper chute to about 45 degrees.
ii).
Pull down the wire leg from under the paper chute.
iii). Insert the wire leg into the grips on the document cover.
iv). Pull out the paper chute extension to the length you want.
Figure 2-4 Setting the ADF Paper Chute
2-5
2.4 ADF Output Tray (Figure 2-5)
i).
Hold the output paper rack some 30 degrees aslant as shown in Figure 2-5.
ii).
Insert the three protrusions on the output paper tray to the three slots on the ADF.
iii).
Release the paper tray gently. Make sure the tray is firmly attached to the ADF.
iv).
Pull out the output paper tray extension wire to the desired length.
Protrusions
Figure 2-5 Install the ADF Output Paper Tray
2-6
2.5 Document Loading
For flatbed scanning.
Documents that can not be scanned using the ADF can be placed on the flatbed for
scanning. Refer to Figure 2-6)
i). Place the document to be scanned onto the document glass face down.
ii). Position the document so that the upper-right corner is aligned with the
reference mark.
Figure 2-6- Place Document on the Scanner
2-7
2.6 ADF Scanning
Standard paper size can be scanned automatically using the ADF. Refer to figure 2-7.
i).
To prevent occasional paper jam when automatically feeding multiple
documents, fan the paper before loading.
ii).
Lift the balance wire and place the documents to be scanned onto the ADF paper
chute face down, with the leading edge in the auto feeder entrance. Let the
balance wire rest on the top of the documents.
iii). Adjust the left and right guides so that they are snug against the sides of the
documents.
Figure 2-7 - Use ADF to Load Multiple Documents
2-8
2.7 Connecting the Cable
i). Turning the Power Off
Depress the side marked “O” to turn the power off.
Connect the power cable and SCSI signal cable as shown in Figure 2-8.
ii). Turning the Power On
Depress the side marked “I” to turn the power on. The POWER LED will light. If
not, please check the power source.
iii). SCSI Termination
The Fujitsu Scanpartner 15C comes complete with a built in SCSI terminator. If
the Scanner is the last device in a SCSI chain the terminator should be switched
on. If the Scanner is not the last device the terminator should be off. The
terminator on/off switch is located on the back of the Scanner, to the left of the
SCSI cable connectors.
Host PC
SCSI Device
Scanner
Term.
Term.
(Terminator Off)
Host PC
Scanner
Term.
(Terminator On)
2-9
SCSI Cable
Figure 2-8 Scanpartner 15C Scanner Cable Connection
Figure 2-9 Scanpartner 15C SCSI Scanner Cable Connections with Mac
2-10
3. MAINTENANCE
3.1 Cleaning the ADF
Your Scanner is designed to be maintenance free. However, it still needs to
be cleaned occasionally to ensure optimum image quality and performance.
From time to time the pad assembly and feeding rollers may become
contaminated with ink, toner particles or paper dust. In this case the
scanner may not feed documents smoothly or several documents may feed
at once. If this occurs please follow the cleaning procedures to return your
Scanner to its original state.
The cleaning procedures (Figure 3-1)
i).
Moisten a cotton swab with isoprophyl alcohol (95%). (Cleaner kits
are available from Fujitsu.)
ii).
Open the ADF unit by depressing the button in front of the ADF
unit, carefully open the ADF to the left . Wipe the feeding rollers by
moving the swab from side to side. Rotate the rollers forward with
your finger and repeat the above cleaning procedures until the rollers
are clean. Be careful not to snag or damage the pick springs.
d
c
iii). Wipe the pad in the direction from top to bottom. Be careful not to
hook the pick springs.
iv). Close the ADF unit. Your Scanner is now ready for use.
1)Documents do not feed smoothly or easily;
2)Several documents feed at one time.
3-1
Figure 3-1 Opening the ADF unit and Document Cover
3-2
3.2 Cleaning the Glass
The procedures:
i).
Soak a cotton swab with some isoprophy alcohol (95%).
ii).
Open the ADF unit and document cover as shown in Figure 6-2.
Wipe the glass of flatbed area and ADF area by moving the swab
from side to side.
iii).
Close the ADF unit and document cover. Your Scanner is
now ready for use.
Figure 3-2 The Cleaning Area
3-3
4. TROUBLESHOOTING
The Scanner will automatically perform a simple self-test each time it is
turned on. This will help spot major system errors in the Scanner itself.
When the test is initiated, the READY LED is flashing. When the test is
completed, if no error occur, the READY LED is steadily on.
If you have problems with the operation of your Scanner, please check the
following troubleshooting hints.
4.1 Question and Answer
Question: The LED indicates that the Scanner is ready, but the Scanner
does not respond to the scan command form the host computer.
Answer:
response,
and
a) Please check the signal cable is firmly seated,
and invoke the scan command again. If there is still no
please reset the Scanner by turning it off and then on again,
reboot your host computer as well.
b) Check if the driver is correctly installed. You can use the
DIAG.EXE file in “Fujitsu Driver Kit” to check this out.
c) Try to select another port memory.
Question: Paper becomes jammed during scanning.
Answer: a) Open the ADF unit.
b) Pull out the jammed paper carefully.
c) Close the ADF unit.
Question: More than one sheet of paper were fed into the Scanner.
Answer: a) Open ADF unit.
b) Remove the multi-fed sheets of paper.
c) Close the ADF unit.
d) Flatten the corners and edges; loosen the paper
before reloading it in the paper guide.
e) Check the feeding roller condition and do the cleaning if
necessary. (See Chapter 3)
4-1
Question: Paper becomes skewed in the Scanner.
Answer: a) Check the feeding roller condition; do the cleaning if
necessary. (See Section 3.1)
b) Use the paper guide when feeding the paper.
Question: When I power on the Scanner, it makes noises and
stand ready.
Answer: There are two possibilities:
will not
a) You forgot to remove the shipping retainer from the Scanner.
Please remove the shipping retainer first.
b) You did not place the Scanner on a flat desktop
This may cause the Scanner to function improperly.
surface.
Question: When I power on the Scanner, the lamp does not light.
Answer: The possibilities are as follows:
a) The lamp is out of order. In that case, contact your
authorized local dealer to change the lamp. The life time of the
lamp is about 5000 hours.
b) The fuse on main board of the Scanner is burned. Check the
main board of the Scanner. If the fuse is burned, put in a new
fuse that is 250V/2A.
c) If the fuse burns again after the changing, it means the
invertor of the lamp is burned. Contact your authorized local
dealer to replace the invertor.
Question: Getting image from the Scanner is not a problem, but when
scanning, the Scanner or system will often crash.
Answer: Please check
a) If the cable is firmly seated;
b) Only two SCSI terminators can be connected to your SCSI daisy
chain. One is at the end of the SCSI device, another is already in
your host adapter.
Question: While scanning, the Scanner often makes
noises, or it scans
back and forth.
Answer: Please choose lower speed from the TWAIN user interface for
low speed PC.
4-2
Question: The scanned image always comes out to be too dark.
Answer: a) Use your application to modify the Gamma setting to 2.2 and
1.8 for your printer and monitor respectively.
b) Use Brightness setting from the TWAIN user interface to get
a brighter image.
Question: The Scanner works well otherwise, but for the line art, the lines
of which seem much thicker than those of the original.
Answer: Use the Brightness or Threshold setting to adjust the line art
image.
4.2 Paper Jam in the ADF
In the event of paper jam, please follow the procedures below.
i). Press the button at the front left of the Scanner as shown in Figure 4-1,
arrow A. The ADF cover will be released.
ii). Open the ADF cover to the full open position, arrow B.
iii). Pull the paper out of the ADF unit carefully, as shown in Figure 4.2,
arrow A.
B
A
Figure 4.1 ADF Paper Jam - Opening the ADF.
4-3
Figure 4.2 ADF Paper Jam - Removing the Paper
4-4
5. SPECIFICATIONS
All specifications are subject to change without notice.
The following can not be properly fed by ADF:
❖
Paper with clip or staple attached;
❖
Paper with ink not totally dry;
❖
Paper with inconsistent thickness, such as envelopes;
❖
Paper with wrinkles, curls, folds or tears;
❖
Tracing paper;
❖
Coated paper;
❖
Carbonless paper;
❖
Paper narrower than 3.5" or wider than 8.5";
❖
Items other than papers, such as cloth, metal or OHP film;
❖
Notched paper;
❖
Paper with an odd (non-rectangular) shape;
❖
Very thin paper.
Please use the flatbed to scan documents that cannot be fed by the ADF.
5-1
5.1 Scanpartner 15C Specifications
Scanner Type
❖ 1-pass colour
❖ Flatbed with ADF built-in
Scanning Mode
❖
❖
❖
❖
Optical Resolution
❖ 300 x 600 dpi in a dpi increments
Light Source
❖ Cold Cathode fluorescent lamp
ADF Capacity
❖ 50 pages
ADF Scanning Speed
❖ 15 PPM (200dpi, B/W mode, ADF)
Scanning Document Size Max.
❖ ADF mode 8.5” x 14”
❖ Flatbed mode 8.5” x 11.69”
Interface
❖ SCSI-2
Power Requirement
❖ 90-264 Vac, 47-63Hz
Power Consumption
❖ 30 watts
Humidity
❖ 20% to 80%
Operation Temperature
❖ 10 to 40
Storage Temperature
❖ -10 to 50
Dimension
❖ 570 x 350 x 165 mm(WxDxH)
Weight
❖ Appropriate 26.5 lbs (12 kg)
30-bit colour
Grey Scale (256 levels)
Line Art/Halftone (64 levels)
Error Diffusion (single bit)
5-2
Download PDF

advertising