LCD TV
OWNER’S MANUAL
LCD TV MODELS
1 9 L S 4 D*
3 2 L G 3 0* *
2 2 L S 4 D*
3 2 L G 3 2* *
3 2 L G 2 0* *
3 7 L G 3 0* *
3 7 L G 2 0* *
4 2 L G 3 0* *
4 2 L G 2 0* *
4 2 L G 3 2* *
1 9 L G 3 0* *
3 2 L G 5* * *
2 2 L G 3 0* *
3 7 L G 5 0* *
2 6 L G 3 0* *
4 2 L G 5 0* *
4 7 L G 5 0* *
5 2 L G 5 0* *
Please read this manual carefully before operating
your TV.
Retain it for future reference.
Record model number and serial number of the TV.
Refer to the label on the back cover and quote this
information.
To your dealer when requiring service.
Trade Mark of the DVB Digital Video
Broadcasting Project (1991 to 1996)
I D N u m b e r ( s ) : 5499: 22LS4D-ZD
5629: 32LG2000-ZA
5630: 37LG2000-ZA
5088: 19LG3000-ZA
5080: 26LG3000-ZA
5087: 37LG3000-ZA
5085: 32LG5000-ZA
5083: 42LG5000-ZA
5081: 52LG5000-ZA
5386: 47LG5010-ZD
5388: 37LG5010-ZD
5390: 52LG5020-ZB
5392: 42LG5020-ZB
5394: 32LG5020-ZB
5396: 47LG5030-ZE
5398: 37LG5030-ZE
5671: 32LG5700-ZF
5818: 22LG3050-ZA
5880: 22LG3060-ZB
6507: 32LG3200-ZA
5507: 19LS4D-ZD
5721: 26LG3050-ZA
5631: 42LG2000-ZA
5090: 22LG3000-ZA
5089: 32LG3000-ZA
5086: 42LG3000-ZA
5084: 37LG5000-ZA
5082: 47LG5000-ZA
5385: 52LG5010-ZD
5387: 42LG5010-ZD
5389: 32LG5010-ZD
5391: 47LG5020-ZB
5393: 37LG5020-ZB
5395: 52LG5030-ZE
5397: 42LG5030-ZE
5399: 32LG5030-ZE
5820: 19LG3050-ZA
5879: 19LG3060-ZB
5878: 32LG5600-ZB
6511: 42LG3200-ZA
Extended Owner’s Manual that contains advanced features of these LG TV-sets is located on CD-ROM in
electronic version.
To read it You need to open chosen files by using
Personal Computer (PC) equipped with CD-ROM drive.
P/NO: MFL34441652 (0901-REV01)
Printed in Korea
CONNECTING YOUR UNIT
■
Image shown may differ from your TV.
..................................................
2
DVD/STB
COMPONENT
IN
2
VIDEO
AV 1
VCR Connection
AV 2
AUDIO
3
Power Cord
USB IN
SERVICE ONLY
AUDIO IN OPTICAL
DIGITAL
(RGB/DVI) AUDIO
OUT
COMPONENT
IN
AV 1
AV 2
VIDEO
HDMI/DVI IN
2
RGB IN (PC)
RS-232C IN
(CONTROL & SERVICE)
AUDIO
1(DVI)
ANTENNA IN
ANTENNA IN
1
Antenna Connection
* To connect an additional equipment, see the E x t e r n a l e q u i p m e n t S e t u p
section in CD Manual.
2
■
Image shown may differ from your TV.
..................................................
3
ENGLISH
Antenna Connection
1
ANTENNA IN
Power Cord
AV 1
ANTENNA IN
AUDIO IN
(RGB/DVI)
HDMI/DVI IN
PCMCIA
CARD SLOT
EJECT
AV 2
RS-232C IN
(CONTROL & SERVICE)
RGB (PC) IN
COMPONENT IN
VIDEO
AUDIO
Y
PB
PR
L
R
SERVICE
ONLY
AV 1
AV 2
COMPONENT IN
VIDEO
AUDIO
Y
2
PB
PR
L
R
VCR Connection
2
DVD/STB
* To connect an additional equipment, see the E x t e r n a l e q u i p m e n t S e t u p
section in CD Manual.
3
SAFETY INSTRUCTIONS
• Please read these safety precautions carefully before using the product.
• In this manual, the illustration may be somewhat different from your product because it is just example to help the instruction.
ENGLISH
WARNING If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death.
CAUTION If you ignore the caution message, you may be slightly injured or the product may be damaged.
Precaution in Installing the Product
WARNING
Keep away from heat sources like electrical heaters.
- Electrical shock, fire, malfunction or deformation may occur.
CAUTION
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched, closed in
a door, or walked upon. Pay particular attention to plugs,
wall outlets, and the point where the cord exits the
appliance.
Precautions in Moving the Product
Do not use the product in damp place such as a bathroom or any place where it is likely to get wet.
- This may cause a fire or could give an electric shock.
If you can smell smoke or other odors or hear a strange
sound unplug the power cord and contact the service
center.
- If you continue to use without taking proper measures, electrical shock or fire can occur.
WARNING
Make sure to turn off the product.
Make sure to remove all cables before moving the
product.
- You may be electrocuted or the product can be damaged.
CAUTION
Do not shock the product when moving it.
CAUTION
Install the product on a flat and stable place that
has no risk of dropping the product.
- If the product is dropped, you may be injured or the
product may be broken.
Keep the product away from direct sunlight.
- The product can be damaged.
Do not place the product in a built-in installation
such as bookcase or rack.
- Ventilation required.
Electrical Power Related Precautions
WARNING
Make sure to connect the power cable to the grounded current.
- You may be electrocuted or injured.
Do not touch the power plug with wet hands.
Additionally, it the cord pin is wet or covered with
dust, dry the power plug completely or wipe dust off.
- You may be electrocuted due to excess moisture.
During a thunder or lightning storm, unplug the
power cable or signal cable.
- You may be electrocuted or a fire can break out.
4
- You may be electrocuted or the product can be damaged.
Make the panel face forward and hold it with both
hands to move.
- If you drop the product, the damaged product can cause electric shock or fire. Contact with the service center for repair.
Precautions in Using the Product
WARNING
Do not disassemble, repair or modify the product at
your own discretion.
- Fire or electric shock accident can occur.
- Contact the service center for check, calibration or
repair.
To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
Apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus.
CAUTION
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug
is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
Do not keep a still image on the screen for an
extended period (e.g. by pausing a video) as the fixed
image may remian visible on the screen. This is known
as image burn. Image burn is not covered under the
manufacturer’s warranty.
PREPARATION
■
■
Image shown may differ from your TV.
If your TV has a protection film attached, remove the film and then wipe the TV with a polishing cloth.
ENGLISH
FRONT PANEL CONTROLS
LCD TV Models :
32/37/42LG20**, 26/32/37/42LG30**, 32/42LG32**, 32/37/42/47/52LG5***
PROGRAMME
P
+
VOLUME
-
Intelligent Sensor
Adjusts picture according to
the surrounding conditions.
(32/37/42/47/52LG5***
only)
OK
OK
MENU
MENU
POWER
Remote Control Sensor
INPUT
INPUT
Power/Standby Indicator
• illuminates red in standby mode.
• illuminates blue when the TV is switched on.
Note: You can adjust Power Indicator
in the OPTION menu.
LCD TV Models : 19/22LG30**
INPUT
MENU OK
VOLUME
INPUT MENU OK
-
+
PROGRAMME
P
LCD TV Models : 19/22LS4D*
MENU
POWER
INPUT
/I
INPUT
MENU
VOLUME
PROGRAMME
OK
OK
VOL
PR
Remote Control Sensor
Power/Standby Indicator
• illuminates red in standby mode.
• illuminates green when the TV is switched on.
5
PREPARATION
Image shown may differ from your TV.
A
1
2
13
3
4
AUDIO IN OPTICAL
DIGITAL
(RGB/DVI) AUDIO
OUT
USB IN
SERVICE ONLY
COMPONENT
IN
AV 1
PCMCIA CARD SLOT
ENGLISH
BACK PANEL INFORMATION
AV 2
VIDEO
HDMI/DVI IN
10
2
AUDIO
RS-232C IN
(CONTROL & SERVICE)
ANTENNA IN
8
2
HDMI/DVI IN
AUDIO IN
(RGB/DVI)
10
ANTENNA IN
PCMCIA
CARD SLOT
AV 2
RS-232C IN
(CONTROL & SERVICE)
RGB (PC) IN
COMPONENT IN
VIDEO
AUDIO
Y
4
PB
7
PR
L
5
Except for
32/37/42LG20**,
32/42LG32**
9
9
EJECT
PCMCIS CARD SLOT
7
5
HDMI IN 3
AV 1
6
S-VIDEO
11
AV IN 3
R
8
12
VIDEO L/MONO AUDIO R
5
VIDEO L/MONO AUDIO R
1(DVI)
HDMI IN 3
RGB IN (PC)
SERVICE
ONLY
H/P
S-VIDEO
6
13
AV IN 3
6
1
Power Cord Socket
This TV operates on an AC power. The voltage is
indicated on the Specifications page. Never
attempt to operate the TV on DC power.
2
RGB/DVI Audio Input
Connect the audio from a PC or DTV.
3
DIGITAL AUDIO OUT OPTICAL (Except for 19/22LS4D*)
Connect digital audio from various types of equipment.
Note: In standby mode, these ports do not work.
H/P
4
Euro Scart Socket (AV1/AV2)
Connect scart socket input or output from an
external device to these jacks.
5
HDMI Input
Connect a HDMI signal to HDMI IN. Or DVI (VIDEO)
signal to HDMI/DVI port with DVI to HDMI cable.
6
RGB IN (PC)
Connect the output from a PC.
7
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
8
Component Input
Connect a component video/audio device to
these jacks.
9
Antenna Input
Connect RF antenna to this jack.
10
PCMCIA (Personal Computer Memory Card
International Association) Card Slot
(This feature is not available in all countries.)
11
Audio/Video Input (Except for 19/22LS4D*)
Connect audio/video output from an external
device to these jacks.
S-VIDEO (Except for 19/22LS4D*, 32/37/42LG20**,
32/42LG32**)
Connect S-Video out from an S-VIDEO device.
12
Headphone Socket (Except for 19/22LS4D*,
32/37/42LG20**, 32/42LG32**)
Connect the headphone plug to this socket.
13
SERVICE ONLY PORT
STAND INSTALLATION
A
When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the
product can tilt forward after the product installation.) If you tighten the bolt with excessive force, the bolt
can deviate from abrasion of the tightening part of the bolt.
1
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
3
Assemble the TV as shown.
2
Assemble the parts of the S t a n d B o d y with
the C o v e r B a s e of the TV.
4
Fix the 4 bolts securely using the holes in the
back of the TV.
ENGLISH
(LCD TV Models: 32/37/42LG20**, 26/32/37/42LG30**, 32/42LG32**, 32/37/42LG5***)
Stand Body
Cover Base
(Only 19/22LG30**)
Stand Body
Cover Base
1
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
2
Assemble the parts of the S T A N D B O D Y with C O V E R B A S E of the TV. Insert the S T A N D B O D Y into a
C O V E R B A S E until clicking sound.
3
Assemble the TV as shown.
7
PREPARATION
ENGLISH
STAND INSTALLATION
DETACHING STAND
(Only 19/22LS4D*)
(Only 19/22LS4D*)
■
Image shown may differ from your TV.
1
2
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
1
Place the tv with its front facing downward on a
cushion or soft cloth.
2
Pull the C o v e r B a s e backward during pressing
a button on the S t a n d B o d y.
3
Hold the C o v e r B a s e and pull with shake it
backward to separate from the S t a n d B o d y.
4
Hold the S t a n d B o d y and bend it upward.
Hold the H i n g e B o d y and bend it upward.
Hinge Body
3
Insert the S t a n d B o d y into the TV until clicking
sound.
Stand Body
4
Assemble the parts of the S t a n d B o d y with
the C o v e r B a s e of the TV.
5
Cover Base
8
Pull stand body to separate from the TV during
pressing 2 latches.
BACK COVER FOR WIRE ARRANGEMENT
1
2
Connect the cables as necessary.
To connect additional equipment, see the External
Equipment Setup section of
the manual.
LCD TV Models :
19/22LS4D*, 19/22LG30**
1
ENGLISH
LCD TV Models:
32/37/42LG20**, 26/32/37/ 42LG30**,
32/42LG32**, 32/37/42/47/52LG5***
Connect the cables as necessary.
To connect additional equipment, see the
External Equipment Setup section.
Open the C A B L E M A N A G E M E N T C L I P as
shown and manage the cables.
2
Install the CABLE MANAGEMENT CLIP as shown.
CABLE MANAGEMENT CLIP
3
(Only 19/22LS4D*)
Fit the C A B L E M A N A G E M E N T C L I P as
shown.
(Only 19/22LG30**)
How to remove the cable management clip
First, press the cable management. Hold the C A B L E
M A N A G E M E N T C L I P with both hands and pull it
upward.
Hold the CABLE MANAGEMENT CLIP with both
hands and pull it backward.
(Only 19/22LS4D*)
(Only 19/22LG30**)
! NOTE
G Do not use the CABLE MANAGEMENT CLIP to lift the TV.
- If the TV is dropped, you may be injured or the TV may be damaged.
9
PREPARATION
PLEASE SET IT UP CAREFULLY SO THE PRODUCT DOES NOT FALL OVER.
ENGLISH
■
■
■
You should purchase necessary components to fix the TV to the wall on the market.
Position the TV close to the wall to avoid the possibility of it falling when pushed.
The instructions shown below are a safer way to set up the TV, which is to fix it to the wall, avoiding the
possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury. This
will also prevent the TV from damage. Ensure that children do not climb or hang from the TV.
1
2
1
2
1
Use the eye-bolts or TV brackets/bolts to fix the TV to the wall as shown in the picture.
(If your TV has bolts in the eyebolts, loosen these bolts.)
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
2
Secure the wall brackets with the bolts on the wall. Match the height of the bracket that is mounted on the
wall.
3
3
Use a sturdy rope to tie the TV. It is safer to tie the rope so it becomes horizontal between the wall and the
TV.
! NOTE
G
G
G
■
■
When moving the TV undo the cords first.
Use a platform or cabinet strong and large enough to support the size and weight of the TV.
To use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.
The TV can be installed in various ways such as on a wall, or on a desktop etc.
The TV is designed to be mounted horizontally.
EARTHING
Ensure that you connect the earth wire to prevent possible
electric shock. If grounding methods are not possible, have a
qualified electrician install a separate circuit breaker.
Do not try to earth the TV by connecting it to telephone
wires, lightening rods or gas pipes.
10
Power Supply
Circuit
breaker
ENGLISH
DESKTOP PEDESTAL INSTALLATION
For adequate ventilation allow a clearance of 4” (10cm) all around the TV.
4 inches
4 inches
4 inches
4 inches
R
Attaching the TV to a desk (Only 32/37/42LG20**, 26/32/37/42LG30**, 32/42LG32**, 32/37/42LG5***)
The TV must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing
injury or damaging the product. Use only an attached screw.
Stand
1-Screw
(provided as parts of the product)
Desk
! WARNING
G
To prevent TV from falling over, the TV should be securely attached to the floor/wall per
installation instructions. Tipping, shaking, or rocking the machine may cause injury.
WALL MOUNT: HORIZONTAL INSTALLATION
For adequate ventilation allow a clearance of 4” (10cm) all around the TV. We recommend that you use a wall
mounting bracket of LG brand when mounting the TV to a wall.
4 inches
4 inches
4 inches
4 inches
4 inches
Not using the desk-type stand (Except for 19/22LS4D*)
■
Image shown may differ from your TV.
When installing the wall-mounted unit, use the protection cover for
desk-type stand installation. Insert the P R O T E C T I O N C O V E R into
the TV until clicking sound.
11
PREPARATION
■
To prevent damage do not connect to the mains outlet until all connections are made between the devices.
ENGLISH
ANTENNA CONNECTION
For optimum picture quality, adjust antenna direction.
■ An antenna cable and converter are not supplied.
■
VIDEO L/MONO AUDIO R
S-VIDEO
AV IN 3
Wall
Antenna
Socket
AV 1
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
HDMI IN
2
VIDEO
AUDIO
ANTENNA
IN
ANTENNA IN
COMPONENT IN
AV 1
AV 2
RGB IN
1
VARIABLE
AUDIO OUT
AV 2
RF Coaxial Wire (75 ohm)
Outdoor
Antenna
(VHF, UHF)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
UHF
Antenna
Signal
Amplifier
ANTENNA IN
AV 1
AV 2
VHF
■
■
12
In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier to the
antenna as shown above.
If signal needs to be split for two TVs,use an antenna signal splitter for connection.
WATCHING TV /PROGRAMME CONTROL
REMOTE CONTROL KEY FUNCTIONS
5
5
1
TV
D/A
6
2
3
TV/RADIO TEXT
7
8
POWER
or
3
I/II
INPUT
MUTE
1
2
3
4
5
6
7
8
9
LIST
0
Q.VIEW
MENU
ENGLISH
When using the remote control, aim it at the remote control sensor on the TV.
6
10
AV MODE
OK
8
GUIDE
INFO i
7
EXIT
RETURN
4
4
*
PR
9
FAV
9
10
VOL
6
INPUT
External input mode rotate in regular sequence.
Switches the TV on from standby.
1
MODE
Selects the remote operating modes.
7
GUIDE
Shows programme schedule.
2
Q. MENU
Select the desired quick menu source.
8
3
MENU
Selects a menu.
Clears all on-screen displays and returns to TV viewing from any menu.
THUMBSTICK(Up/Down/LeftRight)
Allows you to navigate the on-screen menus and
adjust the system settings to your preference.
OK
Accepts your selection or displays the current mode.
9
VOLUME UP /DOWN
Adjusts the volume.
Programme UP/DOWN
Selects a programme.
10
Q.VIEW
Returns to the previously viewed programme.
4
5
POWER
Switches the TV on from standby or off to standby.
Installing Batteries
■
■
■
Open the battery compartment cover on the back and install the batteries matching
correct polarity (+with +,-with -).
Install two 1.5V AAA batteries. Do not mix old or used batteries with new ones.
Close cover.
13
WATCHING TV /PROGRAMME CONTROL
TURNING ON THE TV
ENGLISH
- When your TV is turned on, you will be able to use its features.
1
Firstly, connect the power cord correctly.
At this stage, the TV switches to standby mode.
2
(or PR D E) button on the TV or
In standby mode to turn TV on, press the r / I, INPUT or P
press the POWER, INPUT, D/A, P
(or PR + -) or NUMBER button on the remote control and the
TV will switch on.
Initializing setup
If the OSD (On Screen Display) is displayed on the screen after turning on the TV, you can adjust the
Language, Select Mode, Country, Time Zone, Auto programme tuning.
Note:
a. It will automatically disappear after approx. 40 seconds unless a button is pressed.
b. Press the BACK or RETURN button to change the current OSD to the previous OSD.
c. For those countries without confirmed DTV broadcasting standards, some DTV features might not work,
depending on the DTV broadcasting environment.
d. "Home” mode is the optimal setting for home environments, and is the TV's default mode.
e. "In Store" mode is the optimal setting for store environments.“ If a user modifies image quality data, “In
Store” mode initializes the product to the image quality set by us after a certain period of time.
f. The mode (Home, In Store) can be changed by executing Factory Reset in the OPTION menu.
ON-SCREEN MENU LANGUAGE / COUNTRY SELECTION
The installation guide menu appears on the TV screen when it is switched on for the first time.
2
1
OK
Select your desired language.
Select your country.
OK
* If you want to change Language/ Country selection
1
MENU
2
OK
3
Select O P T I O N.
Select M e n u L a n g u a g e
or C o u n t r y.
OK
Select your desired language or
country.
4
OK
Save it.
! NOTE
G
G
G
G
G
G
14
If you do not finish the set-up Installation Guide by pressing RETURN or if you time out on the OSD (On
Screen Display) the installation menu will continuously appear until the set up is completed whenever the
TV is switched on
If you select the wrong local country, teletext may not appear correctly on the screen and some problems
may occur during teletext operation.
The CI (Common Interface) function may not be applied based on country broadcasting circumstances.
DTV mode control buttons may not function based on country broadcasting circumstances.
In country that Digital broadcasting regulation isn’t fixed, some DTV function may not work depending
on digital broadcasting circumstances.
The Country Setting “UK” should only be activated UK.
ENGLISH
ON SCREEN MENUS SELECTION AND ADJUSTMENT
Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual.
SETUP
Move
OK
PICTURE
Auto tuning
Manual tuning
Programme Edit
Booster
: On
Software Update : Off
Diagnostics
CI Information
Aspect Ratio
Picture Mode
Move
: 16:9
: Vivid
• Backlight
• Contrast
• Brightness
• Sharpness
• Colour
• Tint
100
100
50
70
70
0
OK
R
G
E
AUDIO
SETUP
PICTURE
TIME
OPTION
Auto Volume
Balance
Sound Mode
AUDIO
LOCK
Move
OK
: Off
: Standard
• 120Hz
• 200Hz
• 500Hz
• 1.2KHz
• 3KHz
0
L
R
0
0
0
0
0
-
+
-
+
-
+
-
+
-
+
E
TIME
Move
Clock
Off Time
On Time
Sleep Timer
Auto Sleep
Time Zone
OK
: Off
: Off
: Off
: Off
: Canary GMT
OPTION
Move
Menu Language
Audio Language
Subtitle Language
Hard of Hearing(
Country
Input Label
SIMPLINK
Key Lock
: English
: English
: English
)
Off
:UK
OK
LOCK
Move
OK
Lock System
: Off
Set Password
Block Programme
Parental Guidance : Off
: Off
: Off
E
1MENU
2
OK
3
OK
Display each menu.
Select a menu item.
Move to the pop up menu.
• Press the MENU button to return to normal TV viewing.
• Press the RETURN button to move to the previous menu screen.
15
WATCHING TV /PROGRAMME CONTROL
ENGLISH
AUTO PROGRAMME TUNING
Use this to automatically find and store all available programmes.
When you start auto programming in digital mode, all previously stored service information will be deleted.
SETUP
Move
OK
Auto
Autotuning
tuning
Manual tuning
Programme Edit
Booster
: On
Software Update : Off
Diagnostics
CI Information
1MENU
SETUP
Move
Auto
Autotuning
tuning
Manual tuning
Programme Edit
Booster
: On
Software Update : Off
Diagnostics
CI Information
Select SETUP.
OK
All service-information will be updated.
Continue?
Yes
No
SECAM L Search
• Use NUMBER buttons to input a 4-digit
password in Lock System ‘On’.
2
• If you wish to keep on auto tuning select YES
OK
Select Auto Tuning.
OK
Select Yes.
OK
Run Auto tuning.
3
4
using the
button. Then, press the OK
button. Otherwise select NO.
• Press the MENU button to return to normal TV viewing.
• Press the RETURN button to move to the previous menu screen.
16
APPENDIX
MAINTENANCE
Cleaning the Screen
1
A good way to keep the dust off your screen for a while is to wet a soft cloth in a mixture of lukewarm water
and a little fabric softener or dish washing detergent. Wring the cloth until it is almost dry, and then use it
to wipe the screen.
2
Ensure there is no excess water on the screen. Allow any water or dampness to evaporate before switching on.
ENGLISH
Early malfunctions can be prevented. Careful and regular cleaning can prolong the life of your new TV.
Caution: Be sure to switch the power off and unplug the power cord before you begin any cleaning.
Cleaning the Cabinet
A
A
To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
Do not to use a wet cloth.
Extended Absence
CAUTION
G
If you expect to leave your TV dormant for prolonged periods (such as a holiday), unplug the power
cord to protect against possible damage from lightning or power surges.
TO VIEW THE USER'S GUIDE ON THE CD-ROM
To view the User's guide on the CD-ROM, Adobe Acrobat Reader must be installed on your PC.
The "ACRORD" folder on the CD-ROM contains the installation program for Acrobat Reader.
If you want to install Acrobat Reader, Open "My Computer" Open the folder "LG"
Open the folder "ACRORD"
double-click your language.
To view the User's guide
The User's guide files are included in the supplied CD-ROM.
Load the supplied CD-ROM into the CD-ROM drive of your PC.
After a while, the web page of the CD-ROM will open automatically.(Windows users only)
If the web page does not appear automatically, open the User's guide file directly.
Open "My computer"
Open the folder "LG"
Double click the "index.htm" file.
TROUBLESHOOTING
The TV does not operate properly.
Check to see if there is any object between the TV and the remote control causing
an obstruction. Ensure you are pointing the remote control directly at the TV.
A Ensure that the batteries are installed with correct polarity (+ to +, - to -).
A Ensure that the correct remote operating mode is set: TV, VCR etc.
A Install new batteries.
A
The remote control
does not work
Power is suddenly
turned off
Is the sleep timer set?
Check the power control settings. Has the Power supply been interrupted.
A Is Auto sleep activated on this station?
A
A
17
APPENDIX
The video function does not work.
ENGLISH
Check whether the TV is switched on.
Try another channel. The problem may be with the broadcast.
A Is the power cord inserted correctly into the mains?
A Check your antenna direction and/or location.
A Test the mains outlet by plugging another TV into the same outlet.
A
A
No picture &No sound
Picture appears slowly
after switching on
This is normal, the image is muted during the TV startup process. Please contact
your service centre, if the picture has not appeared after five minutes.
A
Adjust Colour in menu option.
Allow a sufficient distance between the TV and the VCR.
A Try another channel. The problem may be with the broadcast.
A Are the video cables installed properly?
A Activate any function to restore the brightness of the picture.
A
No or poor colour
or poor picture
Horizontal/vertical bars
or picture shaking
Poor reception on
some channels
Lines or streaks
in pictures
No picture
when connecting HDMI
A
Check for local interference such as an electrical appliance or power tool.
A
Station or cable channel experiencing problems, tune to another station.
Station signal is weak, reposition the antenna to receive weaker stations.
A Check for sources of possible interference.
A
A
A
Check antenna (Change the position of the antenna).
A
Check HDMI cable over version 1.3.
If the HDMI cables don’t support HDMI version 1.3, it can cause flickers or no
screen display. In this case use the latest cables that support HDMI version 1.3.
The audio function does not work.
A
Picture OK & No sound
A
A
A
No output from one
of the speakers
Unusual sound from
inside the TV
No sound when
connecting HDMI or
USB
18
Press the VOLUME button.
Sound muted? Press MUTE button.
Try another channel. The problem may be with the broadcast.
Are the audio cables installed properly?
A
Adjust Balance in menu option.
A
A change in ambient humidity or temperature may result in an unusual noise
when the TV is switched on or off and does not indicate a fault with the TV.
A
Check HDMI cable over version 1.3.
Check USB cable over version 2.0.
A
*This feature is not available for all models.
There is a problem with PICTURE settings.
A
It means that the TV is currently set to I n S t o r e mode.
To switch to H o m e mode you should do the followings:
From the TV Menu, choose O P T I O N -> F a c t o r y R e s e t -> Y e s (wait for a
W E L C O M E" appears ->
few seconds for the TV to download again) -> OSD "W
Press O K button -> Choose L a n g u a g e -> Choose H o m e -> Select your
C o u n t r y and T i m e Z o n e -> Press O K button. Program search will begin
automatically (You can stop the search by pressing the O K button). Now, you
have completed switching to the H o m e mode.
ENGLISH
When the user changes
the picture settings, the
TV automatically converts
back to the initial settings
after a certain period of
time.
WEIGHT
19LS4D*
22LS4D*
19LG30**
19LS4D-ZD
22LS4D-ZD
19LG3000-ZA
19LG3050-ZA
19LG3060-ZB
5.1 kg / 11.3 lbs
4.6 kg / 10.2 lbs
6.1 kg / 13.5 lbs
5.7 kg / 12.6 lbs
5.02 kg / 11.1 lbs
4.76 kg / 10.5 lbs
22LG30**
26LG30**
32LG30**
22LG3000-ZA
22LG3050-ZA
22LG3060-ZB
26LG3000-ZA
26LG3050-ZA
32LG3000-ZA
32LG3030-ZA
5.6 kg / 12.4 lbs
5.34 kg / 11.8 lbs
10.1 kg / 22.3 lbs
8.6 kg / 19.0 lbs
13.4 kg / 29.6 lbs
11.9 kg / 26.3 lbs
MODELS
Weight
with stand
without stand
MODELS
Weight
with stand
without stand
MODELS
Weight
with stand
without stand
MODELS
Weight
with stand
without stand
MODELS
Weight
with stand
without stand
■
37LG30**
42LG30**
32LG20**
37LG20**
37LG3000-ZA
37LG3030-ZA
42LG3000-ZA
42LG3030-ZA
32LG2000-ZA
37LG2000-ZA
18.8 kg / 41.5 lbs
16.2 kg / 35.7 lbs
23.6 kg / 52.1 lbs
21.0 kg / 46.3 lbs
13.4 kg / 29.6 lbs
11.9 kg / 26.3 lbs
18.8 kg / 41.5 lbs
16.2 kg / 35.7 lbs
42LG20**
32LG32**
42LG32**
42LG2000-ZA
32LG3200-ZA
42LG3200-ZA
23.6 kg / 52.1 lbs
21.0 kg / 46.3 lbs
13.4 kg / 29.6 lbs
11.9 kg / 26.3 lbs
23.6 kg / 52.1 lbs
21.0 kg / 46.3 lbs
32LG5***
32LG5000-ZA
32LG5010-ZD
32LG5020-ZB
32LG5030-ZE
32LG5600-ZB
32LG5700-ZF
14.1 kg / 31.1 lbs
12.6 kg / 27.8 lbs
37LG50**
42LG50**
47LG50**
52LG50**
37LG5000-ZA
37LG5010-ZD
37LG5020-ZB
37LG5030-ZE
42LG5000-ZA
42LG5010-ZD
42LG5020-ZB
42LG5030-ZE
47LG5000-ZA
47LG5010-ZD
47LG5020-ZB
47LG5030-ZE
52LG5000-ZA
52LG5010-ZD
52LG5020-ZB
52LG5030-ZE
18.3 kg / 40.4 lbs
15.6 kg / 34.4 lbs
26.2 kg / 57.8 lbs
23.5 kg / 51.8 lbs
29.2 kg / 64.4 lbs
24.6 kg / 54.3 lbs
39.5 kg / 87.1 lbs
34.9 kg / 77.0 lbs
The specifications shown above may be changed without prior notice for quality improvement.
19
(UK only)