reliability
Technical manual
System board D1859 (Econel 50)
English
2
Are there ...
... any technical problems or other questions you need clarified?
Please contact:
●
your sales partner
●
your sales outlet
●
our hotline for customers who have purchased the system board as a single delivery unit:
+49(0) 180 3777 005
The latest information and updates (e.g. BIOS update) on our system boards can be found on the
Internet under: http://www.fujitsu-siemens.com
Published by
Fujitsu Siemens Computers GmbH
Edition October 2004
Intel, Pentium and Celeron are registered trademarks of Intel Corporation, USA.
Microsoft, MS, MS-DOS and Windows are registered trademarks of Microsoft Corporation.
PS/2 and OS/2 Warp are registered trademarks of International Business Machines, Inc.
All other trademarks referenced are trademarks or registered trademarks of their respective
owners, whose protected rights are acknowledged.
All rights, including rights of translation, reproduction by printing, copying or similar methods,
even of parts are reserved.
Offenders will be liable for damages.
All rights, including rights created by patent grant or registration of a utility model or design,
are reserved. Delivery subject to availability.
Right of technical modification reserved.
This manual was produced by
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Contents
System board D1859 .......................................................................................................................... 1
Notational conventions ................................................................................................................. 1
Important notes..................................................................................................................................... 2
Information about boards ............................................................................................................. 2
List of features ...................................................................................................................................... 3
Brief instructions on installing system board ........................................................................................ 5
Prior to installation........................................................................................................................ 5
Interfaces and connectors ................................................................................................................. 7
External ports ....................................................................................................................................... 8
LAN connector.............................................................................................................................. 8
Internal ports and connectors ............................................................................................................... 9
Hard disk connection.................................................................................................................... 9
Pin assignment of internal ports ......................................................................................................... 10
Jumper settings................................................................................................................................ 17
Add-on modules / Upgrading .......................................................................................................... 18
Installing and removing processors .................................................................................................... 18
Installing processor with heat sink.............................................................................................. 18
Upgrading main memory .................................................................................................................... 21
Adding PCI Express cards.................................................................................................................. 23
Adding PCI cards................................................................................................................................ 23
PCI bus interrupts - Selecting correct PCI slot ........................................................................... 23
Replacing the lithium battery ...................................................................................................... 25
BIOS update ....................................................................................................................................... 26
BIOS Recovery - Recovering System BIOS....................................................................................... 27
Microcode Update .............................................................................................................................. 28
Annex................................................................................................................................................. 29
System board Revision and BIOS Version......................................................................................... 29
Electrical Properties............................................................................................................................ 30
Error messages ................................................................................................................................ 31
Glossary ............................................................................................................................................ 35
D1859 (Econel 50)
System board D1859
Your system board is available in different configuration levels. Depending on the configuration
chosen, some of the hardware components described may not be available on your system board.
Additional information
Information on the BIOS Setup and additional descriptions of the drivers are contained:
●
in the readme files on your hard disk
●
on the “ServerView Suite” CDs (ServerBooks and ServerSupport)
i
The programme Acrobat Reader must be installed to be able to open the manuals. You will
find the programme on the CD-ROM directory: utls/acrobat.
For more details please read the according readme.txt files.
Notational conventions
The meanings of the symbols and fonts used in this manual are as follows:
►
└┘
!
indicates information which is important for your health or for preventing physical damage.
i
indicates additional information which is required to use the system properly.
Text which follows this symbol describes activities that must be performed in the order shown.
This symbol indicates that you must enter a blank space (press the Space Bar) at this point.
This symbol indicates that you must press the Enter key.
Text in this typeface indicates screen outputs.
Text in this bold typeface indicates the entries you make via the keyboard.
Text in italics indicates commands or menu items.
"Quotation marks" indicate names of chapters or terms.
D1859 (Econel 50)
1
Important notes
Important notes
With the system board installed you must open the system to access the system board. How to
dismantle and reassemble the system is described in the operating manual accompanying the
system.
Connecting cables for peripherals must be adequately shielded to avoid interference.
!
Observe the safety notes in the operating manual of your system.
Incorrect replacement of the lithium battery may lead to a risk of explosion. It is therefore
essential to observe the instructions in the "Add-on modules / Upgrading" - "Replacing the
lithium battery" chapter.
Components can become very hot during operation. Ensure you do not touch
components when making extensions to the system board. There is a danger of burns!
The shipped version of this board complies with the requirements of the EEC directive
89/336/EEC "Electromagnetic compatibility".
Compliance was tested in a typical server configuration.
When installing the board, refer to the specific installation information in the manual for
the receiving device.
i
The warranty is invalidated if the system is damaged during the installation or
replacement of expansions. Information on which expansions you can use is available
from your sales outlet or the customer service centre.
Information about boards
To prevent damage to the system board, the components and conductors on it, please take great
care when you insert or remove boards. Take great care to ensure that extension boards are slotted
in straight, without damaging components or conductors on the system board, or any other
components, for example EMI spring contacts.
Remove the plug from the mains outlet so that system and system board are totally disconnected
from the mains voltage.
Be careful with the locking mechanisms (catches, centring pins etc.) when you replace the system
board or components on it, for example memory modules or processors.
Never use sharp objects (screwdrivers) for leverage.
Boards with electrostatic sensitive devices (ESD) are identifiable by the label shown.
When you handle boards fitted with ESDs, you must, under all circumstances,
observe the following:
●
●
●
●
●
2
You must always discharge static build up (e.g. by touching a grounded object)
before working.
The equipment and tools you use must be free of static charges.
Remove the power plug from the mains supply before inserting or removing
boards containing ESDs.
Always hold boards with ESDs by their edges.
Never touch pins or conductors on boards fitted with ESDs.
D1859 (Econel 50)
List of features
List of features
Onboard features
D1859-A
Chipset
Intel 925
Board size
ATX
VGA
Audio / 8-channel / S/PDIF 5.1
/-/
Buzzer / int. Speaker Support
-/
LAN 1 Gbit / 100 Mbit / 10 Mbit
/
LAN ASF / AOL / WOL / Boot
/-/
Serial ATA / ATA / RAID
FireWire
/
/
/
TM
/
-
USB 2.0
Fan monitoring PSU** / CPU (FAN1) / AUX1 (FAN2) /
AUX2 (FAN3)
/
/
/
Fan control PSU** / CPU (FAN1) / AUX1 (FAN2) / AUX2
(FAN3)
/
/
/
Temperature monitoring CPU/ONB1/ONB2/OFFB
/
/
/-
SmartCard SystemLock (USB / serial)
/-
Fujitsu Siemens Computers Keyboard Power Button
Support
Special onboard features
Silent Fan / Silent Fan LT
/-
System Guard / Silent Drives
Recovery BIOS / Desk Update / Multi Boot / Safe Standby
/
/
/
HDD Password / USB Security
/
Logo Boot / Intel On Screen Branding
/
Internal ports
DIMM Sockets (DDR2 533)
PCI Express 8x / 1x
PCI slot (32 bit, 33 MHz and 3.3 V, Rev. 2.3)
4
1/1
5
Serial ATA interface (150 Mbyte/s)
4
ATA Interface (Ultra DMA/100)
1
Floppy interface
1
/
List of features
Internal ports (continued)
D1859-A
S/PDIF 5.1 (digital Audio)* OUT / IN
-/-
Audio Input
-
Front panel Audio (headphone, microphone, AC97)
-
TM
IEEE 1394 connector* (FireWire )
-
USB Ports* (2.0, ~480 Mbit/s)
4
Serial Ports* (RS232, FIFO, 16550 compatible)
Fan Connectors PSU** / CPU / AUX1 / AUX2
1 / 1 /1 / 1
SMBus Connector* (Case Temperature)
1
Cover monitoring* (Casing open)
1
BTX (24-pin) / ATX12V (4-pin) power supply
1/1
External ports
VGA
1
Audio Mic. In / Line in / Line out (or configurable with
driver)
S/PDIF (digital audio, cinch)* OUT / IN
-/-/-/-
S/PDIF (digital audio, optical) OUT
-
LAN (RJ-45)
1
PS/2 mouse/keyboard
1/1
FireWire™ * (6-Pin, IEEE 1394 port)
-
USB Ports (2.0, ~480 Mbit/s)
4
Serial Ports (RS232, FIFO, 16550 compatible)
1
Parallel Port (EPP/ECP)
1
*
for use with internal devices or optional Front or Rear panel
**
not supported by standard power supplies
4
D1859 (Econel 50)
Brief instructions on installing system board
Brief instructions on installing system board
If you have purchased a separate system board, you can install the system board in your system in
accordance with the following brief instructions.
The activities described here assume a basic knowledge of servers and cannot be carried out by a
layperson. If you are not sure whether you have the necessary specialised knowledge, then leave
this work to an expert.
The illustrations of the system show examples of possible cases.
Prior to installation
►
Please take note of the safety information in the "Important notes" chapter.
►
Check whether the processor, memory modules and power supply are suitable for this system
board:
–
processor (see "Installing and removing processors" chapter).
–
memory modules (see "Upgrading main memory" chapter).
–
power supply (see "Electrical Properties" chapter).
►
Make sure the current requirement of the fans (processor, case) does not exceed the
loadability of the fan connections (see chapter entitled "Electrical Properties").
►
First only install the components absolutely necessary (graphics card, processor and heat sink,
one memory module) and only connect the required connections (power supply unit, case
connections such as ATX on/off switch, hard disk or floppy disk drive). You should not install
additional cards and devices until this minimum configuration successfully boots (see chapter
entitled "Add-on modules / Upgrading").
Installation
►
Equip the system board with the processor, heat sink and memory modules before installation
if possible. Further information can be found in "Installing processor with heat sink" chapter.
►
Open the casing as described in the
operating manual.
Brief instructions on installing system board
►
Should no suitable connection field be
provided in the case, then you must
install the connection field (1) provided.
Ensure the plate is aligned properly so that
the connections are suitable for the system
board later.
►
Set the system board on the edge on
which the connection field is located (2)
and then insert the board in the
case (3).
Make sure that spacers in the housing are
only mounted at points at which there are
mounting holes in the system board.
►
►
Fasten the system board with the
screws.
Connect the plugs for the power supply, control panel and drives to the corresponding
connections on the system board.
Driver installation
►
6
Install the drivers for the chipset. You may find the driver on the "ServerStart” and
“ServerSupport” CDs..
D1859 (Econel 50)
Interfaces and connectors
1
Channel B
Channel A
2
3
4
16
5
15
6
7
slot 4
slot 2
slot 3
slot 1
PCI Express x8
PCI 1
3
PCI Express x1
4
8
SATA
PCI 2
1
2
PCI 3
BIOS
PCI 4
PCI 5
Battery
14
13
12
10
9
1
CPU fan (F1)
2
PC98
10
Intrusion
3
Floppy disk drive
11
I C bus (SMB1)
4
Front panel
12
Fan connector (F3)
5
Extended HD-LED
13
USB1/2
6
IDE primary (IDE1/2)
14
USB3/4
7
ATX power 24pin (PWR1)
15
TPM jumper (optional)
8
Serial ATA 1-4
16
ATX power 4pin (PWR2)
D1859 (Econel 50)
9
11
Fan connetor (F2)
2
7
External ports
External ports
1
8
2
7
3
6
5
4
1
PS/2 mouse port
5
VGA port
2
Parallel port/printer
6
Serial interface COM1
3
LAN connector (10/100/1000 Mbit/s)
7
USB1 connector
4
USB0 connector
8
PS/2 keyboard board
LAN connector
The system board is optionally equipped with the Broadcom BCM5751 LAN controller. This LAN
controller supports the transfer rates 10 Mbit/s, 100 Mbit/s and 1000 Mbit/s. The LAN controller
TM
supports the WOL functionality through Magic Packet , Basic Alert-on-LAN II and ASF 2.0 (Alert
Standard Format).
It is also possible to boot a device without its own boot hard disk via LAN. Here bootix® BootP and
Intel PXE are supported.
The LAN RJ45 connector has two LEDs (light emitting diodes).
1
2
LED 1 lights green - a connection exists (e.g. to a hub). LED is blinking green: activity
LED 2 lights green or yellow:
Link Mode: the LAN connection is active.
10 Mbit/s
100 Mbit/s
1000 Mbit/s
8
off
green
yellow
D1859 (Econel 50)
Internal ports and connectors
Internal ports and connectors
The positions of the internal ports and connectors are shown on the Cover. Additional information on
some ports is also provided here.
Hard disk connection
If you have connected hard disks to serial ATA (one hard disk is possible per serial ATA connection),
you must configure the respective settings in the BIOS Setup (further information you can find in the
BIOS Setup manual).
An ultra ATA/66 or ultra ATA/100 hard disk must be connected with a cable especially designed for
the ultra ATA/66 or ultra ATA/100 mode.
►
Connect the end of the cable marked with blue to the system board.
A serial ATA/150 hard disk must be connected with a serial ATA cable.
►
Connect the cable to the hard disk and to the connector on the system board.
D1859 (Econel 50)
9
Pin assignment of internal ports
Pin assignment of internal ports
The pin assignment of some internal connections is shown in English in the following.
i
Some of the following connectors may be optional!
Front panel
1) Message LED
Power On
HD-LED
LED 2)
Power On/Off
Watch the poling of the LEDs. The positive pole
of the connection cables is often indicated with a
coloured wire.
Reset
1
2
Recovery Password
1) Both jumper positions possible
2) 2pin or 3pin connector possible
Speaker
Connection
Note
Reset
Power On/Off
HD LED
Message LED
Power On LED
Recovery
Password
Speaker
Connector for reset switch
Connection for ATX On/Off switch
Indicates HDD (hard disk) activity
Indicates system management error
Indicates the system state APM or ACPI
see "Fehler! Verweisquelle konnte nicht gefunden werden." chapter
see "Fehler! Verweisquelle konnte nicht gefunden werden." chapter
0,5 W at 8 Ohm
1
Serial ATA
10
Pin
Signal
Pin
Signal
1
3
5
7
GND
Transmit data negative
Receive data negative
GND
2
4
6
8
Transmit data positive
GND
Receive data positive
Key
D1859 (Econel 50)
Pin assignment of internal ports
IDE/ATA interface
2
1
Pin
Signal
Pin
Signal
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Reset drive (low asserted)
Data 7 (high asserted)
Data 6 (high asserted)
Data 5 (high asserted)
Data 4 (high asserted)
Data 3 (high asserted)
Data 2 (high asserted)
Data 1 (high asserted)
Data 0 (high asserted)
GND
DRQ (high asserted)
I/O write (low asserted)
I/O read (low asserted)
I/O ready (low asserted)
DAK (low asserted)
IRQ (high asserted)
ADR 1 (high asserted)
ADR 0 (high asserted)
CS 1 (low asserted)
IDE-LED (low asserted)
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
GND
Data 8 (high asserted)
Data 9 (high asserted)
Data 10 (high asserted)
Data 11 (high asserted)
Data 12 (high asserted)
Data 13 (high asserted)
Data 14 (high asserted)
Data 15 (high asserted)
Key
GND
GND
GND
Cable select
GND
not connected
ATA66 Detect (low asserted)
ADR 2 (high asserted)
CS 3 (low asserted)
GND
D1859 (Econel 50)
11
Pin assignment of internal ports
USB - dual channel
2
11
12
Pin
Signal
Pin
Signal
1
Key
2
3
5
7
9
11
VCC 1 or 3
Data negative 1 or 3
Data positive 1 or 3
GND
Key
4
6
8
10
12
Chipcardreader on
or not connected
VCC 2 or 4
Data negative 2 or 4
Data positive 2 or 4
GND
not connected
Fan
12
1
1
Pin
Signal
1
2
3
4
GND
+12 V
Fan sense
Fan Control
D1859 (Econel 50)
Pin assignment of internal ports
Floppy interface
1
Pin
Signal
Pin
Signal
1
2
3
4
5
6
7
8
9
10
GND
FDHDIN (low asserted)
GND
not connected
Key
not connected
GND
Index (low asserted)
GND
Motor A Enable (low
asserted)
GND
Drive B Select (low
asserted)
GND
Drive A Select (low
asserted)
GND
18
19
20
21
22
23
24
25
26
27
Step DIR (low asserted)
GND
Step Pulse (low asserted)
GND
Write Data (low asserted)
GND
Write Enable (low asserted)
GND
Track 0 (low asserted)
GND
28
29
Write Protect (low asserted)
GND
30
31
Read Data (low asserted)
GND
32
Motor B Enable (low
asserted)
GND
33
Side 1 Select (low
asserted)
GND
34
Disk Change (low asserted)
11
12
13
14
15
16
17
D1859 (Econel 50)
13
Pin assignment of internal ports
2
LCD display
1
Pin
Signal
Pin
Signal
1
2
3
4
5
6
SMB CLK
GND
SMB DATA
GND
Key
RFU
Reserved for Future use
LAN Active Icon
8
9
10
11
12
13
LAN Link Icon
Harddisk Action Icon
BMC Alert Icon
Message Icon
Sleep Icon
Power Icon
14
P3V3P_DUAL
7
Intrusion
14
1
Pin
Signal
1
2
3
GND
Case open (low asserted)
Intrusion switch present (low asserted)
D1859 (Econel 50)
Pin assignment of internal ports
1
Power supply BTX
(ATX compatible)
13
Pin
Signal
Pin
Signal
1
2
3
4
5
6
7
8
9
10
11
12
+3.3 V (P3V3P)
+3.3 V (P3V3P)
GND
+5V (VCC)
GND
+5V (VCC)
GND
Powergood (high asserted)
+5 V Auxiliary (VCC Aux)
+12 V (P12VP)
+12 V (P12VP)
13
14
15
16
17
18
19
20
21
22
23
24
+3.3 V (P3V3P)
-12 V (P12VN)
GND
PS on (low asserted)
GND
GND
GND
-5 V (P5VN)
+5 V (VCC)
+5 V (VCC)
+5 V (VCC)
GND
Additional power supply ATX12 V
3
1
Pin
Signal
Pin
Signal
1
3
GND
+12 V
2
4
GND
+12 V
D1859 (Econel 50)
15
Pin assignment of internal ports
1
Power supply control
(System monitoring)
16
Pin
Signal
1
2
4
Power Guard Control
PS FAN Control
PS FAN Sense
D1859 (Econel 50)
Jumper settings
The positions of the jumpers are shown on page "Cover".
Setting via control-panel plug connector
A
1
2
Pin pair A inserted =
Skipping system and BIOS Setup password
B
1
2
Pin pair B inserted = System BIOS recovery
C
1
2
Pin pair C inserted = factory setting
i
Please pay attention on the exact position of the pin pairs!
Skipping system and BIOS Setup password - pinpair A
Pinpair A enables skipping the system and BIOS Setup password.
Inserted
System and BIOS Setup password are skipped when the device is switched on and
may be changed.
Not inserted
System and BIOS Setup password must be entered when the device is switched on.
Recovering System BIOS - pinpair B
Pinpair B enables recovery of the old system BIOS after an attempt to update has failed. To restore
the old BIOS you need a Flash BIOS Diskette (see "BIOS update" chapter).
Inserted
The System BIOS executes from floppy drive A: and the inserted "Flash-BIOSDiskette" restores the System BIOS on the system board.
Not inserted
Normal operation (default setting).
17
D1859 (Econel 50)
Add-on modules / Upgrading
!
Exit energy-saving mode, switch off the system and remove the power plug from the
mains outlet, before carrying out any of the procedures described in this chapter!
Even when you have run down the device, parts of the device (e.g. memory modules, PCI
extension boards) are still energised.
Installing and removing processors
Technical data
●
Intel Pentium 4 with 800 MHz front side bus (FSB) in the LGA775 design.
●
A current list of the processors supported by this system board is available in the service
documentation.
Installing processor with heat sink
!
►
Never touch the underside of the processor. Even minor soiling such as grease from the
skin can impair the processor's operation or destroy the processor.
Place the processor in the socket with extreme care, as the spring contacts of the socket
are very delicate and must not be bent.
Remove the heat sink.
2
1
►
Press down the lever (1) and unhook it.
►
Fold up the frame.
►
Remove the old processor (2) from the socket.
18
D1859 (Econel 50)
Add-on modules / Upgrading
a
►
Insert the new processor in the socket so that the marking of the processor is aligned with the
marking on the socket (a).
1
2
3
►
Fold down the frame (1).
►
Press the lever downward (2) until it is hooked in again (3).
D1859 (Econel 50)
19
Add-on modules / Upgrading
Mounting heat sink
i
Use only the heat sink supplied with your system!
Be sure to use heat conducting material between the processor and the heat sink. If a heat
conducting pad (rubber-like foil) is already applied to the heat sink, then use it. Otherwise you must
apply a very thin layer of heat conducting paste.
Heat conducting pads can only be used once. If you remove the heat sink, you must clean it and
apply new heat conducting paste before you remount it.
►
Depending on the configuration variant, you
must pull a protective foil off the heat sink or
coat the heat sink with heat conducting
paste before fitting it.
►
Secure the heat sink - depending on the
model - with four screws or push it into the
mounts.
1
2
22
2
2
20
D1859 (Econel 50)
Add-on modules / Upgrading
Upgrading main memory
Technical data
Technology:
DDR2 400 / DDR2 533 unbuffered DIMM modules
184-Pin; 1.8 V; 64 Bit, with ECC
Size:
256 Mbytes to 4 Gbytes DDR2
Granularity:
256, 512 or 1024 Mbyte for one socket
A current list of the memory modules recommended for this system board is available on the Internet
at: www.fujitsu-siemens.com.
At least one memory module must be installed. Memory modules with different memory capacities
can be combined.
!
i
You may only use unbuffered 1,8 V memory modules with ECC.
DDR2 memory modules must meet the PC3200 or PC4300 specification.
The system board has two memory channels (channel A and channel B) with two slots
each (slot 1 and 3 or slot 2 and 4).
If you use more than one memory module, then make sure to distribute the memory
modules over both memory channels. By doing this you use the performance advantages
of the dual-channel mode.
The maximum system performance is given when the same memory size is used in
Channel A and Channel B.
To simplify equipping, the slots are colour coded.
With a memory configuration of 4 Gbytes the visible and usable main memory can be
reduced down to 3 Gbytes (depending on the system configuration).
D1859 (Econel 50)
slot 4
Channel B
slot 2
slot 3
Channel A
slot 1
21
Add-on modules / Upgrading
Installing a memory module
2
2
►
Push the holders on each side of the memory slot outwards.
►
Insert the memory module into the location (1).
►
At the same time flip the lateral holders upwards until the memory module snaps in place (2).
Removing a memory module
1
1
►
Push the clips on the right and left of the memory slot outward (1).
►
Pull the memory module out of the memory slot (2).
22
D1859 (Econel 50)
Add-on modules / Upgrading
Adding PCI Express cards
The PCI Express x8 slot is intended for graphics cards, and the PCI Express x1 slot for
PCI Express x1 cards.
Adding PCI cards
Technical data:
32 bit / 33 MHz PCI slots
3.3 V supply voltage (PCI 2.3 compliant)
3.3 V auxiliary voltage
PCI bus interrupts - Selecting correct PCI slot
i
To achieve optimum stability, performance and compatibility, avoid the multiple use of ISA
IRQs or PCI IRQ Lines (IRQ sharing). Should IRQ sharing be unavoidable, then all
involved devices and their drivers must support IRQ sharing.
PCI IRQ Lines connect PCI/PCI Express slots and onboard components to the interrupt controller.
IRQ Lines are permanently wired on the system board.
Which ISA IRQs are assigned to the PCI IRQ Lines is normally automatically specified by the BIOS
(see description in "BIOS Setup").
Monofunctional expansions cards:
PCI/PCI Express expansion cards require a maximum of one interrupt, which is called the PCI
interrupt INT A. Expansion cards that do not require an interrupt can be installed in any desired slot.
D1859 (Econel 50)
23
Add-on modules / Upgrading
Multifunctional expansion cards or expansion cards with integrated PCI-PCI bridge:
These expansion cards require up to four PCI interrupts: INT A, INT B, INT C, INT D. How many and
which of these interrupts are used is specified in the documentation provided with the card.
The assignment of the PCI interrupts to the IRQ Lines is shown in the following table:
Controller or slot INT
Mechanical slot
On board controller
PCI
INT
LINE
1
2
3
4
rd
4
th
PCIe x1
3
PCI Slot 1
nd
PCIe x8
2
LAN
st
SMBus
1
5
6
7
Slot PCI
USB 2.0
USB 1.1
2
3
4
5
1 (A)
–
–
–
–
–
–
A
–
C
–
–
–
–
2 (B)
–
–
–
–
–
–
–
B
–
D
–
–
–
A
3 (C)
–
–
–
–
–
–
X
–
D
A
C
A
D
B
C
4 (D)
–
–
–
–
–
X
–
–
C
B
D
B
A
5 (E)
–
–
–
X
–
–
–
–
–
–
–
–
–
–
6 (F)
–
–
X
–
–
–
–
–
B
–
A
C
B
D
7 (G)
–
X
–
–
–
–
–
–
A
–
B
D
C
–
8 (H)
X
–
–
–
X
–
–
–
–
–
–
–
–
–
Use first PCI/PCI Express slots that have a single PCI IRQ Line (no IRQ sharing). If you must use
another PCI/PCI Express slot with IRQ sharing, check whether the expansion card properly supports
IRQ sharing with the other devices on this PCI IRQ Line. The drivers of all cards and components on
this PCI IRQ Line must also support IRQ sharing.
24
D1859 (Econel 50)
Add-on modules / Upgrading
Replacing the lithium battery
In order to permanently save the system information, a lithium battery is installed to provide the
CMOS-memory with a current. A corresponding error message notifies the user when the charge is
too low or the battery is empty. The lithium battery must then be replaced.
!
Incorrect replacement of the lithium battery may lead to a risk of explosion!
The lithium battery may be replaced only with an identical battery or with a type
recommended by the manufacturer.
Do not throw lithium batteries into the household waste. They must be disposed of in
accordance with local regulations concerning special waste.
Make sure that you insert the battery the right way round. The plus pole must be on the
top!
The lithium battery holder exists in different designs that function in the same way.
3
2
4
2
1
3
►
Press the locking lug in the direction of the arrow; the battery jumps somewhat out of the
holder (1).
►
Remove the battery (2).
►
Push the new lithium battery of the identical type into the holder (3) and press it downward until
it engages (4).
D1859 (Econel 50)
25
Add-on modules / Upgrading
BIOS update
When should a BIOS update be carried out?
Fujitsu Siemens Computers makes new BIOS versions available to ensure compatibility to new
operating systems, new software or new hardware. In addition, new BIOS functions can also be
integrated.
A BIOS update should always also be carried out when a problem exists that cannot be solved with
new drivers or new software.
Where can I obtain BIOS updates?
The BIOS updates are available on the Internet at www.fujitsu-siemens.de/support.
BIOS update under DOS with bootable BIOS update floppy disk - brief description
►
Download the update file from out website to your server.
►
Insert an empty floppy disk (1.44 MB).
►
Run the update file (e.g. 1858103.EXE).
►
A bootable update floppy disk is created. Leave this floppy disk in the drive.
►
Restart the server.
►
Follow the instructions on screen.
26
D1859 (Econel 50)
Add-on modules / Upgrading
BIOS Recovery - Recovering System BIOS
i
All BIOS settings are reset to the default values.
►
Open the casing as described in the operating manual.
►
On the system board set the jumper to the appropriate setting to restore the system BIOS (see
chapter "Jumper settings").
►
Close the casing as described in the operating manual.
►
Insert a BIOS update floppy disk and start the server.
►
Note the signals issued from the loudspeaker. You have successfully restored the BIOS if you
hear the signal sequence "short-short- long- long- long" and the diskette access indicator is
dark. This can take a few minutes.
►
Open the casing as described in the operating manual.
►
Restore the switch or jumper settings.
►
Close the casing as described in the operating manual.
►
Remove the floppy disk from the drive.
►
Start the server and invoke BIOS Setup.
►
Select the menu item Reset Configuration in the menu Advanced and change the setting to Yes.
►
Save the change and terminate BIOS Setup.
The BIOS recovery has now been completed. The system restarts.
i
Detailed information on the BIOS recovery is contained in the manual "BIOS Setup"
("ServerBooks" CD).
D1859 (Econel 50)
27
Add-on modules / Upgrading
Microcode Update
What is a microcode update?
As there are no drivers for processors, Intel offers the possibility from the P6 family (Pentium Pro) on
to update the command set (microcode) of the processor. This enables minor errors to be corrected
and the performance to be increased.
To guarantee the best possible performance and error-free operation, Intel recommends updating
the microcode for every new processor. Intel refers to the use of the processor without microcode
updates as operation outside the specifications.
Safety for processor on Fujitsu Siemens Computers system boards
If the processor uses an old or incorrect microcode, error-free operation cannot be ensured. Fujitsu
Siemens Computers has therefore implemented a function on its system boards that interrupts the
booting process if no suitable microcode is available for the installed processor. The output error
message is
Patch for installed CPU not loaded. Please run the bios flash update
diskette.
This message appears until the microcode update has been carried out. If the computer is
nevertheless operated without a microcode update, error-free operation is not ensured.
When should a microcode update be carried out?
A microcode update should be carried out after the installation of a new processor.
In contrast to the BIOS update, only an updated version of the processor command set is stored. The
system BIOS remains unaffected by this.
Microcode update under DOS with bootable microcode update floppy disk - brief description
►
Download the update file from out website to your server.
►
Insert an empty floppy disk (1.44 MB).
►
Run the update file under DOS (e.g. 1858101.EXE).
►
A bootable update floppy disk is created. Leave the floppy disk in the drive.
►
Restart the server.
►
Follow the instructions on screen.
To determine whether the latest microcode update has been loaded, the so-called Patch-ID of the
processor can be read out.
Press the F1 key in the BIOS Setup.
►
The entry CPU / Patch ID is shown on the displayed information page.
A list with the current processors and the related Patch-IDs is available on the Internet.
i
28
If the processor is not recognised, you also require the microcode update tool for
processors of the P6 family.
D1859 (Econel 50)
Annex
Annex
System board Revision and BIOS Version
System board Revision
The revision status of the system board exactly identifies which system board you have. It is
indicated on a sticker on the edge of the system board:
D1859-A10 GS 1
05618476
Example System board revision
BIOS version
The BIOS version can be displayed in the BIOS Setup.
►
Press F2 during booting to open the BIOS Setup.
►
Press F1 .
The BIOS version is specified on the displayed information page under the entry BIOS Release.
D1859 (Econel 50)
29
Annex
Electrical Properties
Loadability for connections and fuses
i
Make sure that the connected devices do not overload the connections.
Fuse no.
Fuse
Connection
Maximum loadability
1
750 mA
2
2000 mA
3
2000 mA
Keyboard
Mouse
USB port 1
USB port 2
USB port 3
USB port 4
USB port 5
USB port 6
USB port 7
USB port 8
Not specified
Not specified
500 mA
500 mA
500 mA
500 mA
500 mA
500 mA
500 mA
500 mA
The fuses on this system board can be used several times (polyfuses). Shortly after the error state
has been eliminated, the fuses reset to the original state.
30
D1859 (Econel 50)
Error messages
Error messages
This chapter contains error messages generated by the system board.
Available CPUs do not support the same bus frequency - System halted!
Memory type mixing detected
Non Fujitsu Siemens Memory Module detected - Warranty void
There are more than 32 RDRAM devices in the system
Check whether the system configuration has changed. If necessary, correct the settings.
BIOS update for installed CPU failed
This message appears if the microcode update required for the connected processor is not
contained in the system BIOS.
►
Boot the system with the inserted Flash BIOS floppy disk.
►
Abort the normal Flash BIOS update by answering the question about whether you want to
perform the update with
n
►
To carry out the Flash BIOS update for the processor, enter:
flashbio++/p6
Check date and time settings
The system date and time are invalid. Set the current date and time in the Main menu of the
BIOS Setup.
CPU ID 0x failed
Switch the server off and on again. If the message is still displayed, go into the BIOS setup and
set the corresponding processor to Disabled in the Server - CPU Status menu; please contact
your sales outlet or customer service centre.
CPU mismatch detected
You have replaced the processor or changed the frequency setting. As a result, the
characteristic data of the processor have changed. Confirm this change by running the BIOS
Setup and exiting it again.
Diskette drive A error
Diskette drive B error
Check the entry for the diskette drive in the Main menu of the BIOS Setup. Check the
connections to the diskette drive.
D1859 (Econel 50)
31
Error messages
DMA test failed
EISA CMOS not writable
Extended RAM Failed at offset: nnnn
Extended RAM Failed at address line: nnnn
Failing Bits: nnnn
Fail-Safe Timer NMI failed
Multiple-bit ECC error occurred
Memory decreased in size
Memory size found by POST differed from EISA CMOS
Single-bit ECC error occurred
Software NMI failed
System memory exceeds the CPU’s caching limit
System RAM Failed at offset: nnnn
Shadow RAM Failed at offset: nnnn
Switch the device off and on again. If the message is still displayed, please contact your sales
outlet or customer service centre.
Failure Fixed Disk 0
Failure Fixed Disk 1
Fixed Disk Controller Failure
Check the entry for the hard disk drive in the Main menu and the entry for the IDE drive
controller in the Advanced - Peripheral Configuration menu of the BIOS Setup. Check the hard disk
drive's connections and jumpers.
Incorrect Drive A - run SETUP
Incorrect Drive B - run SETUP
Correct the entry for the diskette drive in the Main menu of the BIOS Setup.
Invalid NVRAM media type
Switch the device off and on again. If the message is still displayed, please contact your sales
outlet or customer service centre.
Invalid System Configuration Data
In the Advanced menu of the BIOS Setup set the entry Reset Configuration Data to Yes.
Invalid System Configuration Data - run configuration utility
Press F1 to resume, F2 to Setup
This error message may be displayed if the machine was switched off during system start-up.
Call BIOS Setup and switch to the Advanced menu. Select the menu item Reset Configuration Data
and change the setting to Yes. Save the change and terminate BIOS Setup. Reboot the device.
Keyboard controller error
Connect another keyboard or another mouse. If the message is still displayed, please contact
your sales outlet or customer service centre.
Keyboard error
Check that the keyboard is connected properly.
32
D1859 (Econel 50)
Error messages
Keyboard error nn
nn Stuck Key
Release the key on the keyboard (nn is the hexadecimal code for the key).
Missing or invalid NVRAM token
Switch the device off and on again. If the message is still displayed, please contact your sales
outlet or customer service centre.
Monitor type does not match CMOS - RUN SETUP
Correct the entry for the monitor type in the Main menu of the BIOS Setup.
On Board PCI VGA not configured for Bus Master
In the BIOS Setup, in the Advanced menu, submenu PCI Configuration, set the Shared PCI Master
Assignment entry to VGA.
One or more RDRAM devices are not used
One or more RDRAM devices have bad architecture/timing
One or more RDRAM devices are disabled
Contact your system administrator or contact our customer service centre.
Operating system not found
Check the entries for the hard disk drive and the floppy disk drive in the Main menu and the
entries for Boot Sequence submenu of the BIOS Setup.
Parity Check 1
Parity Check 2
Switch the device off and on again. If the message is still displayed, please contact your sales
outlet or customer service centre.
Previous boot incomplete - Default configuration used
By pressing function key F2 you can check and correct the settings in BIOS Setup. By pressing
function key F1 the system starts with incomplete system configuration. If the message is still
displayed, please contact your sales outlet or customer service centre.
Real time clock error
Call the BIOS Setup and enter the correct time in the Main menu. If the message is still
displayed, please contact your sales outlet or customer service centre.
System battery is dead - Replace and run SETUP
Replace the lithium battery on the system board and redo the settings in the BIOS Setup.
System Cache Error - Cache disabled
Switch the device off and on again. If the message is still displayed, please contact your sales
outlet or customer service centre.
System CMOS checksum bad - Default configuration used
Call the BIOS Setup and correct the previously made entries or set the default entries.
D1859 (Econel 50)
33
Error messages
System Management Configuration changed or Problem occurred
A system fan or system sensor has failed. Check the hardware operation.
System timer error
Switch the device off and on again. If the message is still displayed, please contact your sales
outlet or customer service centre.
Uncorrectable ECC DRAM error
DRAM Parity error
Unknown PCI error
Switch the device off and on again. If the message is still displayed, please contact your sales
outlet or customer service centre.
Verify CPU frequency selection in Setup
The frequency setting for the processor is invalid. Correct the BIOS Setup and the setting.
34
D1859 (Econel 50)
Glossary
The technical terms and abbreviations given below represent only a selection of the full list of
common technical terms and abbreviations.
Not all technical terms and abbreviations listed here are valid for the described system board.
AC'97
Audio Codec '97
IPSEC
Internet Protocol Security
ACPI
Advanced Configuration and
Power Management Interface
LAN
Local Area Network
AOL
Alert On LAN
APM
Advanced Power Management
ATA
Advanced Technology
Attachment
BIOS
Basic Input Output System
BMC
Baseboard management
controller
CAN
Controller Area Network
CPU
Central Processing Unit
DIMM
Dual Inline Memory Module
ECC
Error Correcting Code
EEPROM
Electrical Erasable
Programmable Read Only
Memory
FDC
Floppy disk controller
FIFO
First-In First-Out
FSB
Front Side Bus
FWH
Firmware Hub
GMCH
Graphics and Memory
Controller Hub
GPA
Graphics Performance
Accelerator
2
LSA
LAN Desk Service Agent
MCH
Memory Controller Hub
MMX
MultiMedia eXtension
P64H
PCI64 Hub
PCI
Peripheral Component
Interconnect
PCI Express Peripheral Component
Interconnect Express
PXE
Preboot eXecution Environment
RAM
Random Access Memory
RAMDAC
Random Access Memory
Digital Analogue Converter
RTC
Real Time Clock
SATA
Serial Advanced Technology
Attachment
SB
Soundblaster
SDRAM
Synchronous Dynamic Random
Access Memory
SIMD
Streaming Mode Instruction
(Single Instruction Multiple
Data)
SMBus
System Management Bus
SVGA
Super Video Graphic Adapter
IC
Inter Integrated Circuit
USB
Video Graphic Adapter
IAPC
Instantly Available Power
Managed Desktop PC Design
WOL
Wake On LAN
ICH
I/O Controller Hub
IDE
Intelligent Drive Electronics
35
D1859 (Econel 50)
Information on this document
On April 1, 2009, Fujitsu became the sole owner of Fujitsu Siemens Computers. This new subsidiary of Fujitsu has been renamed Fujitsu Technology Solutions.
This document from the document archive refers to a product version which
was released a considerable time ago or which is no longer marketed.
Please note that all company references and copyrights in this document have
been legally transferred to Fujitsu Technology Solutions.
Contact and support addresses will now be offered by Fujitsu Technology Solutions and have the format …@ts.fujitsu.com.
The Internet pages of Fujitsu Technology Solutions are available at
http://ts.fujitsu.com/...
and the user documentation at http://manuals.ts.fujitsu.com.
Copyright Fujitsu Technology Solutions, 2009
Hinweise zum vorliegenden Dokument
Zum 1. April 2009 ist Fujitsu Siemens Computers in den alleinigen Besitz von
Fujitsu übergegangen. Diese neue Tochtergesellschaft von Fujitsu trägt seitdem den Namen Fujitsu Technology Solutions.
Das vorliegende Dokument aus dem Dokumentenarchiv bezieht sich auf eine
bereits vor längerer Zeit freigegebene oder nicht mehr im Vertrieb befindliche
Produktversion.
Bitte beachten Sie, dass alle Firmenbezüge und Copyrights im vorliegenden
Dokument rechtlich auf Fujitsu Technology Solutions übergegangen sind.
Kontakt- und Supportadressen werden nun von Fujitsu Technology Solutions
angeboten und haben die Form …@ts.fujitsu.com.
Die Internetseiten von Fujitsu Technology Solutions finden Sie unter
http://de.ts.fujitsu.com/..., und unter http://manuals.ts.fujitsu.com finden Sie die
Benutzerdokumentation.
Copyright Fujitsu Technology Solutions, 2009