Service manual | Fujitsu D2530 Computer Hardware User Manual

PRIMERGY
System Board D2530
for Econel 200 S2
Technical Manual
Susanne Däschlein
Fujitsu Siemens Computers GmbH München
81730 München
e-mail: email: manuals@fujitsu-siemens.com
Tel.: (089) 61001-155
Fax: (++49) 700 / 372 00000
D2530 (Econel 200 S2)
Sprachen: En
Edition November 2006
Comments… Suggestions… Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Fax forms for sending us your comments are included in
the back of the manual.
There you will also find the addresses of the relevant
User Documentation Department.
Certified documentation
according to DIN EN ISO 9001:2000
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2000.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademarks
Copyright © 2006 Fujitsu Siemens Computers GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.
Contents
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2
Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1
Notes on safety . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2
CE Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.3
Environmental Protection . . . . . . . . . . . . . . . . . . . 11
3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.2
Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.3
PCI bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.4
Screen resolution
3.5
Temperature / system monitoring . . . . . . . . . . . . . . . 18
3.6
3.6.1
Connectors and jumpers . . . . . . . . . . . . . . . . . . . . 20
External connectors . . . . . . . . . . . . . . . . . . . . . . . 22
4
Replacing the lithium battery . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . 18
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
D2530 (Econel 200 S2)
Technical Manual
1
Introduction
This technical manual describes the system board D2530, which can be
equipped with one or two Intel® processors.
Further information about drivers is provided in the readme files on the hard
disk, on the supplied "ServerSupport" or "ServerStart" CDs.
You will find further information in the BIOS description.
Notational conventions
The meanings of the symbols and fonts used in this manual are as follows:
italics
indicates commands, menu items, file and path
names or software programs
fixed font
indicate system output on the monitor
semi-bold fixed
font
indicates values to be entered through the keyboard
[Key symbol]
indicates keys according to their representation on the
keyboard
If capital letters are to be entered explicitly, then the
Shift key is shown, e.g. [SHIFT] - [A] for A.
If two keys need to be pressed at the same time, then
this is shown by placing a hyphen between the two key
symbols.
“quotation marks”
indicates names and terms that are being emphasized.
Ê
indicates an operation that to be performed
V CAUTION!
I
indicates warnings, which, if ignored, will endanger
your health, destroy the system or lead to the loss of
data.
indicates additional information, notes and tips
Table 1: Notational conventions
D2530 (Econel 200 S2)
Technical Manual
5
2
Important notes
In this chapter you will find essential information regarding safety when working
with your server.
V CAUTION!
With the system board installed you must open the system to access the
system board. How to access the system board of your system is
described in the appropriate service supplement.
When handling the system board, refer to the specific notes on safety in
the operating manual and/or service supplement for the respective
server.
2.1
Notes on safety
V CAUTION!
●
The actions described in these instructions should only be performed
by authorized, qualified personnel. Equipment repairs should only be
performed by qualified staff. Any failure to observe the guidelines in
this manual, and any unauthorized openings and improper repairs
could expose the user to risks (electric shock, fire hazards) and could
also damage the equipment. Please note that any unauthorized
openings of the device will result in the invalidation of the warranty
and exclusion from all liability.
●
Transport the device only in the antistatic original packaging or in
packaging that protects it from knocks and jolts.
●
Only install expansions that are allowed for the system board. If you
install other expansions, you may damage the requirements and rules
governing safety and electromagnetic compatibility or your system.
Information on which system expansions are suitable can be
obtained from the customer service centre or your sales outlet.
●
The warranty expires if the device is damaged during the installation
or replacement of system expansions.
D2530 (Econel 200 S2)
Technical Manual
7
Notes on safety
V
Important notes
●
Components can become very hot during operation. Ensure you do
not touch components when making extensions to the system board.
There is a danger of burns!
●
Transmisson lines to peripheral devices must be adequately shielded.
●
To the LAN wiring the requirements apply in accordance with the
standards EN 50173 and EN 50174-1/2. As minimum requirement
the use of a protected LAN line of category 5 for 10/100 MBps
Ethernet, and/or of category 5e for Gigabit Ethernet is considered.
The requirements of the specification ISO/IEC 11801 are to be
considered.
●
Never connect or disconnect data transmission lines during a storm
(lightning hazard).
Batteries
V CAUTION!
●
Incorrect replacement of lithium battery may lead to a risk of
explosion. The batteries may only be replaced with identical batteries
or with a type recommended by the manufacturer.
It is essential to observe the instructions in chapter “Replacing the
lithium battery”.
8
Technical Manual
D2530 (Econel 200 S2)
Important notes
Notes on safety
Modules with electrostatic-sensitive components
Systems and components that might be damaged by electrostatic discharge
(ESD) are marked with the following label:
Figure 1: ESD label
When you handle components fitted with ESDs, you must observe the following
points under all circumstances:
●
You must always discharge yourself of static charges (e.g. by touching a
grounded object) before working.
●
The equipment and tools you use must be free of static charges.
●
Remove the power plug from the power socket before inserting or removing
boards containing ESDs.
●
Always hold boards with ESDs by their edges.
●
Never touch pins or conductors on boards fitted with ESDs.
●
Use a grounding cable designed for this purpose to connect yourself to the
system unit as you install/deinstall the board.
●
Place all components on a static-safe base.
I You will find a detailed description for handling ESD components in the
relevant European or international standards (EN 61340-5-1,
ANSI/ESD S20.20).
D2530 (Econel 200 S2)
Technical Manual
9
CE Certificate
Important notes
Notes about boards
●
During installation/deinstallation of the system board, observe the specific
instructions described in the service manual for the server.
●
Remove the plug from the mains outlet so that system and system board are
totally disconnected from the mains voltage.
●
To prevent damage to the system board, the components and conductors on
it, please take great care when you insert or remove boards. Take great care
to ensure that extension boards are slotted in straight, without damaging
components or conductors on the system board, or any other components,
for example EMI spring contacts
●
Be careful with the locking mechanisms (catches, centring pins etc.) when
you replace the system board or components on it, for example memory
modules or processors.
●
Never use sharp objects (screwdrivers) for leverage.
2.2
CE Certificate
The shipped version of this board complies with the requirements
of the EEC directive 89/336/EEC "Electromagnetic compatibility".
Compliance was tested in a typical PRIMERGY configuration.
10
Technical Manual
D2530 (Econel 200 S2)
Important notes
2.3
Environmental Protection
Environmental Protection
Environmentally friendly product design and development
This product has been designed in accordance with standards for ”environmentally friendly product design and development“. This means that the designers
have taken into account important criteria such as durability, selection of
materials and coding, emissions, packaging, the ease with which the product
can be dismantled and the extent to which it can be recycled.
This saves resources and thus reduces the harm done to the environment.
Notes on saving energy
Devices that do not have to be on permanently should not be switched on until
they need to be used and should be switched off during long breaks and on
completion of work.
Notes on packaging
Please do not throw away the packaging. We recommend that you do not throw
away the original packaging in case you need it later for transporting.
Notes on dealing with consumables
Please dispose batteries in accordance with local government regulations.
Do not throw batteries and accumulators into the household waste. They must
be disposed of in accordance with local regulations concerning special waste.
All batteries containing pollutants are marked with a symbol (a crossed-out
rubbish bin on wheels). In addition, the marking is provided with the chemical
symbol of the heavy metal decisive for the classification as a pollutant:
Cd Cadmium
Hg Mercury
Pb Lead
Notes on labeling plastic housing parts
Please avoid attaching your own labels to plastic housing parts wherever
possible, since this makes it difficult to recycle them.
D2530 (Econel 200 S2)
Technical Manual
11
Environmental Protection
Important notes
Returning, recycling and disposal
The device may not be disposed of with household rubbish. This
appliance is labelled in accordance with European Directive
2002/96/EC concerning used electrical and electronic appliances
(waste electrical and electronic equipment - WEEE).
The guideline determines the framework for the return and recycling
of used appliances as applicable throughout the EU. To return your
used device, please use the return and collection systems available
to you. You will find further information on this at www.fujitsusiemens.com/recycling.
For details on returning and reuse of devices and consumables within Europe,
refer to the “Returning used devices” manual, or contact your Fujitsu Siemens
Computers branch office/subsidiary or our recycling centre in Paderborn:
Fujitsu Siemens Computers
Recycling Center
D-33106 Paderborn
Tel.
+49 5251 8 18010
Fax
+49 5251 8 18015
12
Technical Manual
D2530 (Econel 200 S2)
Features
Overview
3
Features
3.1
Overview
Processors
– 2 x Intel® Xeon™ Dual Core processors
– 2 processor sockets Dual LGA771 for Intel® Xeon™ Dual Core processor
with 1333/1066/667 MHz front side bus
– supports Intel® Extended Memory 64 Technology (EM64T)
– supports Intel® Hyper-Threading Technology (H.T.), except: 5100 series
Main memory
– 4 slots for main memory FBD533/PC2-4200F Fully Buffered DIMM memory
modules with 512 MB, 1Gbyte and 2Gbyte
– maximum 8 Gbyte of memory
– minimum 512 MB
– ECC multiple bit error detection and single bit error correction
– memory scrubbing function
– Single Device Data Correction (SDDC) function (Chipkill™)
Chipsets on the system board
Intel® 5000V chipset Memory Controller Hub (MCH)
Intel® 6321 I/O Controller Hub (ICH) with integrated GBit LAN
Intel® Single 1 GB PHY 82564EB onboard
VGA controller (ATI® ES1000) onboard with 32 MB RAM memory
1 MBYTE Flash EPROM für:
– System BIOS
– Onboard Video
– Onboard LAN
– Onboard LSI Software RAID
– Onboard SATA
– system management controller (temperature, voltages, fans) W83793G
–
–
–
–
–
D2530 (Econel 200 S2)
Technical Manual
13
Overview
Features
Internal connectors
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
floppy disk
1 IDE primary
6 SATA connectors
SATA-HDD access (HDLED)
2 USB connectors
1 serial port connector (COM2)
PC98 connector
1 parallel port connector (LPT1)
front panel
main power connector (12V, -12V, 5V, 3.3V and 5V auxiliary)
12V (CPU) power connector
2 CPU fans
1 rear fan
BPSMB connector
BPSMB connector
RAID key
External connectors
–
–
–
–
–
1 serial port (COM1)
2 PS/2 interfaces for keyboard and mouse
2 USB 2.0 ports with 480 Mbits/s (rear)
1 VGA port
1 RJ45 LAN port
PCI slots
–
–
–
–
3 x PCI-X (133/100 MHz)
1 x PCI 33 MHz
1 x PCI-Express x16 slot (x8 wired)
1 x PCI-Express x8 slot (x4 wired)
BIOS features
– AMI (American Megatrend BIOS)
Form factor
12“ x 10.5“
14
Technical Manual
D2530 (Econel 200 S2)
Features
3.2
Main memory
Main memory
The system board supports up to 8 Gbyte main memory. 4 slots (2 banks with
2 modules) are available for the main memory. Each memory bank can be
populated with 512 Mbyte, 1 Gbyte or 2 Gbyte FBD533/PC2-4200F Fully
Buffered DIMM memory modules.
ECC with memory scrubbing and with the Single Device Data Correction
(SDDC) function is supported.
I You will find the descriptions how to install memory modules in the
Options Guide of your server.
Module population
DIMM 2B
DIMM 1B
DIMM 2A
DIMM 1A
Figure 2: Main memory
– If the memory modules are populated in pairs, each pair must consist of
identical memory modules (2-way interleaved mode)
– The module capacity between pairs can differ: pair 2A/2B can be populated
with two 512 Mbyte modules and pair 1A/1B with two 1 Gbyte modules.
Following table shows the mandatory population order:
DIMM 1A
DIMM 2A
single channel
populated
dual channel
populated
populated
D2530 (Econel 200 S2)
DIMM 1B
DIMM 2B
empty
empty
empty
empty
populated
empty
populated
populated
populated
Technical Manual
15
PCI bus
3.3
Features
PCI bus
slot 6
PCI-Express x16
slot 5
PCI-Express x8
slot 4
PCI 33MHz
slot 3
PCI-X 133/100 MHz
slot 2
PCI-X 133/100 MHz
slot 1
PCI-X 133/100 MHz
Figure 3: PCI slots
PCI slots
The following table shows an overview of the PCI slots:
PCI slot
64Bit/
32Bit
Frequency Description
in MHz
1
133/100
PCI-X bus slot, IOOP
2
133/100
PCI-X bus slot, IOOP
3
4
133/100
32 Bit
33
PCI-X bus slot, IOOP
PCI bus slot
5
PCI-Express x8 slot (x4 accessed)
6
PCI-Express x16 slot (x8 accessed)
PCI IRQ Line x - Assignment of the PCI interrupts
PCI IRQ Line x defines which ISA interrupts are used for the separate PCI slots.
If you select Auto in the BIOS setup, the interrupts are assigned automatically
and no further settings are required.
Multifunctional PCI boards or boards with an integrated PCI-to-PCI bridge can
use several PCI interrupts (INTA#, INTB#, INTC#, INTD#). Monofunctional PCI
boards (default) only use one PCI interrupt (INTA#) per PCI slot.
16
Technical Manual
D2530 (Econel 200 S2)
Features
PCI bus
The PCI interrupts INTA#, INTB#, INTC# and INTD# are available for each PCI
slot (except the PCI-Express slots).
The same interrupt can be assigned simultaneously to several PCI boards. You
should avoid this condition due to reduced performance.
If you use a setting other than Auto, the Plug&Play functionality of the system
BIOS for the corresponding PCI boards is deactivated.
Auto
The PCI interrupts are assigned automatically in accordance with
the Plug&Play guidelines.
Disabled
No ISA interrupt is assigned to the PCI interrupt.
3, 4, 5, 6, 7, 9, 10, 11, 12, 14, 15
The selected ISA interrupt is assigned to the PCI interrupt. You
may not select an ISA interrupt that is used by a component on
the system board (e.g. controller) or an ISA board.
Device
Bus
Slot 1
IDsel
INTA
INTB
PCI-X
19
PXIRQ8
PXIRQ9
Slot 2
PCI-X
18
PXIRQ4
Slot 3
PCI-X
17
PXIRQ0
Slot 4
PCI
17
PIRQA
PIRQB
Slot 5
PCI-Express
Slot 6
PCI-Express
VGA
PCI
18
PIRQB
LAN
PIRQE
USB UHCI
PIRQA
INTC
INTD
PXIRQ10
PXIRQ11
PXIRQ5
PXIRQ6
PXIRQ7
PXIRQ1
PXIRQ2
PXIRQ3
PIRQC
PIRQD
Controller #0
USB UHCI
Controller #1
PIRQD
USB UHCI
Controller #2
PIRQC
USB UHCI
Controller #3
PIRQA
USB 2.0 EHCI
PIRQH
D2530 (Econel 200 S2)
Technical Manual
17
Screen resolution
3.4
Features
Screen resolution
Depending on the operating system used the screen resolutions in the following
table refer to the screen controller on the system board. If you are using an
external screen controller, you will find details of supported screen resolutions
in the operating manual or technical manual supplied with the controller.
Possible refresh rates (Hz) 1)
Color depth
(bits pro pixel, bpp)
640x480
60, 72, 75, 85, 90, 100, 120, 160, 200
8, 16 2), 32 2)
800x600
60, 70, 72, 75, 85, 90, 100, 120, 160, 200
8, 16 2), 32 2)
1024x768
60, 70, 72, 75, 85, 90, 100, 120, 140, 150, 160,
200
8, 16 2), 32 2)
1152x864
43, 47, 60, 70, 75, 80, 85, 100, 120, 150, 160
8, 16 2), 32 2)
1280x1024
60, 70, 74, 75, 85, 90, 100, 120
8, 16 2), 32 2)
1600x1200
52, 58, 60, 66, 75
8, 16 2), 32 2)
Screen
resolution
1)
depending on the operating system specific video drivers
2)
depending on the selected refresh rate and the modified video memory clock
3.5
Temperature / system monitoring
Temperature and system monitoring aim to reliably protect the computer
hardware against damage caused by overheating. In addition, any unnecessary
noise is also prevented by reducing the fan speed, and information is provided
about the system status.
The temperature and system monitoring is controlled by an onboard controller.
The following functions are supported:
Temperature monitoring
Measurement of the processor temperature, measurement of the ambient
temperature by a temperature sensor on the LED board.
Fan monitoring
Fans that are no longer available, blocked or sticky fans are detected.
18
Technical Manual
D2530 (Econel 200 S2)
Features
Temperature / system monitoring
Fan control
The fans are controlled according to temperature.
Sensor monitoring
The removal of, or a fault in, a temperature sensor is detected. Should this
happen all fans monitored by this sensor run at maximum speed, to achieve the
greatest possible protection of the hardware.
Voltage monitoring
The most important voltages are monitored. When a voltage exceeds warning
level high or falls below warning level low an alert will be generated. Adequate
measurements can be done by running agents.
Cover monitoring
Unauthorised opening of the cover is detected, even when the system is
switched off. However, this will only be indicated when the system is switched
on again
System Event Log (SEL)
All monitored events of the system board are recorded in the System Event Log.
They could be retrieved after a system reboot via ServerView.
D2530 (Econel 200 S2)
Technical Manual
19
Connectors and jumpers
3.6
Features
Connectors and jumpers
1
2
4
3
5
6
CPU 1
DIMM 2B
DIMM 1B
27
DIMM 2A
DIMM 1A
CPU 2
26
25
24
Battery
PCI-E x8
RAID
key
8
PCI 33MHz
PCI-X 133/100 MHz
A
PCI-X 133/100 MHz
PCI-X 133/100 MHz
21
20 19
18
17 16 15 14 13 12
11
SATA5 SATA3 SATA1
22
7
PCI-E x16
SATA6 SATA4 SATA2
23
9
10
Figure 4: Schematic overview of the system board D2530
1 = KBPWR (jumper)
2 = USBPW 1/2 (jumper)
3 = power supply ATX
4 = PC98
5 = power supply12V (CPU1, CPU2)
6 = CPU1 fan
20
15 = USBPW 3/4 (jumper)
16 = USB 3/4
17 = BPSMB
18 = floppy disk
19 = BIOSREC (jumper)
20 = COM2
Technical Manual
D2530 (Econel 200 S2)
Features
Connectors and jumpers
7 = CPU2 fan
8 = RAID key
9 = SATA 1 - 6
10 = USB 7/8
11 = IDE primary
12 = HDLED
13 = intrusion
14 = front panel
21 = LPT1
22 = VGA_EN (jumper)
23 = CLRTC (jumper)
24 = LAN_EN (jumper)
25 = LAN_BW (jumper)
26 = rear fan
27 = external connectors
A = 5V Standby LED
Settings with jumpers
The system board is supplied with all jumpers set on default position (pin 1-2).
KBPWR (1)
1-2
PS/2 keyboard/mouse powered by 5V (default)
2-3
PS/2 keyboard/mouse powered by 5V Standby
USBPW 1/2 (2) and USBPW 3/4 (15)
1-2
USB device powered by 5V (default)
2-3
USB device powered by 5V Standby
BIOSREC (19)
1-2
system BIOS (default)
2-3
recover system BIOS (Flash BIOS, Recovery Diskette required)
VGA_EN (22)
1-2
onboard VGA enabled (default)
2-3
onboard VGA disabled (PCI VGA graphics controller)
CLRTC (23)
1-2
CMOS/RTC settings are not cleared (default)
2-3
clear CMOS/RTC settings
D2530 (Econel 200 S2)
Technical Manual
21
Connectors and jumpers
Features
LAN_EN (24)
1-2
onboard LAN enabled (default)
2-3
onboard LAN disabled (PCI LAN controller)
LAN_BW (25)
1-2
LAN bandwidth setting to balanced mode (default)
2-3
LAN bandwidth setting to centric mode
LED
5V Standby(A)
lightning green standby power present
off
3.6.1
AC loss or system board not connected to power supply unit
External connectors
1
2
3
4
5
6
Figure 5: External connectors of the system board D2530
1 = PS/2 mouse port
4 = Serial port COM1
2 = PS/2 keyboard port
5 = VGA port
3 = USB port 1/2
6 = LAN port
22
Technical Manual
D2530 (Econel 200 S2)
Features
Connectors and jumpers
LAN connector
On this system board you will find a LAN controller integrated in the Intel® 6321
I/O controller Hub (ICH). This controller is supported by an external chip (Intel®
Single 1 GB PHY 82564EB), which is connected to the I/O controller Hub via an
original Intel interface (Kumeran Interface). The LAN controller supports the
transfer rates of 10 Mbit/s, 100 Mbit/s and 1 Gbit/s and supports WOL function
through Magic Packet™.
It is also possible to boot a device without its own boot hard disk via LAN. Here
Intel PXE is supported.
The LAN controller connector is equipped with two LEDs (light emitting diode)
indicating the transfer rate and the activity.
1
2
Figure 6: LAN connector
1
2
LAN link/activity
LAN transfer rate
D2530 (Econel 200 S2)
green
on
LAN connection
off
no LAN connection
flashing
LAN transfer
green + orange off
transfer rate 10 Mbit/s (or no
connection)
green
on
transfer rate 100 Mbit/s
orange
on
transfer rate 1000 Mbit/s
Technical Manual
23
4
Replacing the lithium battery
In order to save the system information permanently, a lithium battery is
installed to provide the CMOS-memory with a current. When the charge is too
low or the battery is empty, a corresponding error message is provided. The
lithium battery must then be replaced.
V The lithium battery must be replaced with an identical battery or a battery
type recommended by the manufacturer (CR2032).
Do not throw lithium batteries into the trashcan. It must be disposed of in
accordance with local regulations concerning special waste.
Make sure that you insert the battery the right way round. The plus pole
must be on the top!
4
2
3
1
Figure 7: Replacing the lithium battery
Ê Press the locking spring into direction of of the arrow (1), so that the lithiumbattery jumps out of its socket.
Ê Remove the battery (2).
Ê Insert a new lithium battery of the same type into the socket (3) and (4).
D2530 (Econel 200 S2)
Technical Manual
25
Abbreviations
The technical terms and abbreviations given below represent only a selection of
the full list of common technical terms and abbreviations.
Not all technical terms and abbreviations listed here are valid for the described
system board.
AC
Alternating Current
ACPI
Advanced Configuration and Power management Interface
ANSI
American National Standards Institute
ASR&R
Automatic Server Recovery and Restart
ATA
Advanced Technology Attachment
BBU
Battery Backup Unit
BIOS
Basic Input Output System
BMC
Baseboard Management Controller
CMOS
Complementary Metal Oxide Semiconductor
COM
COMmunication port
CPU
Central Processing Unit
D2530 (Econel 200 S2)
Technical Manual
27
Abbreviations
DDR
Double Data Rate
DIMM
Dual In-line Memory Module
DIP
Dual In-line Package
DMI
Desktop Management Interface
DRAM
Dynamic Random Access Memory
ECC
Error Correction Code
EEPROM
Electrical Erasable Programmable Read Only Memory
EFI
Extensible Firmware Interface
EGB
Elektrostatisch gefährdete Bauteile
EHCI
Enhanced Host Controller Interface
EMI
Electromagnetic interference
EMRL
Embedded RAID Logic
EMV
Elektromagnetische Verträglichkeit (electromagnetic compatibility)
EPROM
Erasable Programmable Read Only Memory
28
Technical Manual
D2530 (Econel 200 S2)
Abbreviations
ESD
ElectroStatic Discharge (elektrostatische Entladung)
EVRD
Enterprise VRD
HPC
Hotplug Controller
FPC
Front Panel Controller
FRU
Field Replaceable Unit
FSB
Front Side Bus
ICE
In Circuit Emulation
IDE
Integrated (intelligent) Drive Electronics
IEC
International Electrotechnical Commission
IME
Integrated Mirroring Enhanced
IOOP
Intelligent Organisation Of PCI
IPMB
Intelligent Platform Management Bus
IPMI
Intelligent Platform Management Interface
iRMC
integrated Remote Management Controller
D2530 (Econel 200 S2)
Technical Manual
29
Abbreviations
ISO
International Organisation for Standardisation
LAN
Local Area Network
LED
Light Emitting Diode
MPS
Multi Processor Specification
NMI
Non Maskable Interrupt
OEM
Original Equipment Manufacturer
OHCI
Open Host Controller Interface
OS
Operating System
PCI
Peripheral Components Interconnect
PDA
Prefailure Detection and Analyzing
PIO
Programmed Input Output
PDB
Power Distribution Board
PLD
Programmable Logic Device
PS(U)
Power Supply (Unit)
30
Technical Manual
D2530 (Econel 200 S2)
Abbreviations
PWM
Pulse Wide Modulation
PXE
Preboot eXecution Environment
RAID
Redundant Array of Inexpensive Disks
RoHS
Restriction of the Use of Certain Hazardous Substances (Waste from
Electric and Electronic Equipment, EU Directive)
RoMB
RAID on Motherboard
RSB
Remote Service Board
RST
ReSeT
RTC
Real Time Clock
SAS
Serial Attached SCSI
SATA
Serial ATA
SCSI
Small Computer Systems Interface
SDDC
Single Device Data Correction
SDRAM
Synchronous Dynamic Random Access Memory
SEL
System Event Log
D2530 (Econel 200 S2)
Technical Manual
31
Abbreviations
SHDG
Server Hardware Design Guide
SMB
System Management Bus
SMM
Server Management Mode
SMP
Symmetrical Multi Processing
UHCI
Unified Host Controller Interface
USB
Universal Serial Bus
VGA
Video Graphics Adapter
VRD
Voltage Regulator Down
VRM
Voltage Regulator Module
WEEE
Waste from Electric and Electronic Equipment (EU Directive)
WfM
Wired for Management
WOL
Wake up On LAN
32
Technical Manual
D2530 (Econel 200 S2)
Fujitsu Siemens Computers GmbH
User Documentation
81730 München
Germany
Fax: (++49) 700 / 372 00000
e-mail: manuals@fujitsu-siemens.com
http://manuals.fujitsu-siemens.com
Submitted by
✁
Comments on System Board D2530
for Econel 200 S2
D2530 (Econel 200 S2)
Comments
Suggestions
Corrections
Download PDF

advertising