Fujitsu DSL25X Printer User Manual

INTERFACE BOARDS FOR
FTP-627/637DCL/ DSL25X SERIES
■ INTERFACE
1. Centronics interface
(1) Connector (CN1)
Connector part number
: BM30B-SRDS-G-TFC (JST) or equivalent
Mating connector part number : SHDR-30V-S-B (JST) or equivalent
(2) Connector pin assignment
No.
Signal
I/O
Contents
No.
Signal
I/O
Contents
1
PRSTB
I
Data strobe
2
PRSTB-RET
—
Connected to logic GND
3
PRDT0
I
Data 0
4
PRDT0-RET
—
Connected to logic GND
5
PRDT1
I
Data 1
6
PRDT1-RET
—
Connected to logic GND
7
PRDT2
I
Data 2
8
PRDT2-RET
—
Connected to logic GND
9
PRDT3
I
Data 3
10
PRDT3-RET
—
Connected to logic GND
11
PRDT4
I
Data 4
12
PRDT4-RET
—
Connected to logic GND
13
PRDT5
I
Data 5
14
PRDT5-RET
—
Connected to logic GND
15
PRDT6
I
Data 6
16
PRDT6-RET
—
Connected to logic GND
17
PRDT7
I
Data 7
18
PRDT7-RET
—
Connected to logic GND
19
ACKNLG
O
Data input acknowledge
20
ACKNLG-RET
—
Connected to logic GND
21
BUSY
O
Busy
22
BUSY-RET
—
Connected to logic GND
23
RINF2
O
Printer status 2
24
INPRM-RET
—
Connected to logic GND
25
SLCTIN
I
Printer select
26
INPRM
I
Reset
27
RINF1
O
Printer status 1
28
RINF3
O
Printer status 3
29
ATF
I
Paper feed request
30
GND
—
Logic GND
Notes: • Symbol “——” means a negative logic signal.
• “–RET” signal is a return signal of the twisted pair cable.
• “I” or “O” means a signal direction from the interface board side.
(3) Connector pin number
(4) Data input signal timing
BM30B-SRDS-G-TF (JST)
PRDT0~7
t1
t3
PRSTB
t2
BUSY
t4
ACKNLG
t5
Data set time
PRSTB pulse width
Data hold time
PRSTB to BUSY= “H”
ACKNLG pulse time
:t1≥0.5 µsec
:t2≥0.5 µsec
:t3≥0.5 µsec
:t4≤0.5 µsec
:t5≈ 5.0 µsec
1
FTP-627/637DCL / DSL25x
(5) Printer status signals
Error status
RINF1
RINF2
RINF3
1.
Paper out
Low
High
Low
2.
Paper near end
High
High
Low
3.
Head up
High
Low
Low
4.
Head temperature abnormality
High
Low
High
5.
Head voltage abnormality
Low
High
High
6.
Hardware abnormality
High
High
High
7.
Mark detection abnormality
Low
Low
Low
8.
Normal
Low
Low
High
2. RS-232C
(1) Connector (CN2)
Connector part number
: B8B-ZR-SM3A-TF (J.S.T.) or equivalent
Mating connector part number : ZHR-8 (J.S.T.) or equivalent
(2) Connector pin assignment
No.
Signal
I/O
Contents No.
No.
Signal
I/O
Contents No.
1
RD
I
Receive data
2
TD
O
Transmission data
3
DTR
O
Data terminal ready
4
GND
-
Signal ground
5
DSR
I
Data set ready
6
SLCTIN
I
Printer select
7
INPRM
I
Reset
8
AFT
I
Paper feed request
Notes:
• Symbol “——” means a negative logic signal.
• “I” or “O” means a signal direction from the interface board side.
2
FTP-627/637DCL / DSL25x
■ CONNECTOR PIN ASSIGNMENT OF MECHANISM (FPC)
1. Thermal Head (CN 3)
2. Cutter unit (CN 4)
Part number : 52610-2490 Molex or equivalent
Part number : 52610-0890 Molex or equivalent
FTP-627MCL401 PIN ASSIGNMENT
FTP-627MCL401PIN ASSIGNMENT
No
Signal
I/O
Contents
No
Signal
I/O Contents
1
PHK
—
Cathode
1
VSEN
O
Logic power supply
2
VSEN
O
Logic power supply
2
PHE
I
Home Position
Signal
3
PHE
4
+24 V
—
Power supply for thermal head
3
PHK
-
Cathode side of
sensor
5
DO
O
Print data out signal
4
MTA
-
Cutter drive signal
6
STB2
O
5
MT/A
-
Cutter drive signal
6
MTB
-
Cutter drive signal
7
MT/B
-
Cutter drive signal
8
N.C.
-
Not connected
|
Paper out detection signal
Head energizing control signal
7
STB3
O
8
+5V
O
9
GND
—
10
GND
—
11
GND
—
12
TM
I
Thermistor
13
STB1
O
Head energizing signal
14
LAT
O
Print data latch signal
15
CLK
O
Datacomm clock signal
16
+24V
—
17
+24V
—
18
SW
O
19
SW
—
20
MT-A
—
21
MT-/A
—
22
MT-B
—
23
MT-/B
—
24
NC
—
Logic power supply
Gound of power supply
Power supply for thermal head
Platen open detection signal
Phase signal for motor
Not connected
3
FTP-627/637DCL / DSL25x
■ CONNECTOR PIN ASSIGNMENT OF MECHANISM (FPC)
1. Thermal Head (CN 9)
2. Cutter unit (CN10)
Part number : 52610-3090 Molex or equivalent
Part number : 52610-0890 Molex or equivalent
FTP-637MCL401 PIN ASSIGNMENT
FTP-637MCL401PIN ASSIGNMENT
No
Signal
I/O
Contents
1
PHK
—
Cathode
2
VSEN
O
Logic power supply
3
PHE
4
+24 V
|
Paper out detection signal
No
Signal
I/O Contents
1
VSEN
O
Logic power supply
2
PHE
I
Home Position
Signal
3
PHK
-
Cathode side of
sensor
4
MTA
-
Cutter drive signal
5
MT/A
-
Cutter drive signal
6
MTB
-
Cutter drive signal
7
MT/B
-
Cutter drive signal
8
N.C.
-
Not connected
—
5
+24V
—
6
+24V
—
7
DO
O
8
STB3
O
Power supply for thermal head
Print data out signal
Head energizing signal
9
STB4
O
10
+5V
O
11
GND
—
12
GND
—
13
GND
—
14
GND
—
15
GND
—
16
GND
—
17
TM
18
STB1
O
19
STB2
O
20
LAT
O
Print data latch signal
21
CLK
O
Datacomm clock signal
22
+24V
—
23
+24V
—
24
+24V
—
25
SW
|
26
SW
O
27
MT-A
—
28
MT-/A
—
29
MT-B
—
30
MT-/B
—
Logic power supply
Ground for thermal head
|
Thermistor
Head energizing signal
Power supply for thermal head
Platen open detection signal
Phase signal for motor
4
FTP-627/637DCL / DSL25x
■ INTERFACE BOARD CONNECTOR PIN ASSIGNMENT
1. Connector for logic power supply (CN6)
Part number
No.
Signal
: S3B-PH-SM3-TB (J.S.T) or equivalent (board side)
I/O
Contents No.
1
+5V
-
Power supply for logic
3
GND
-
Ground
No.
Signal
2
I/O
NC
-
Contents No.
No connection
2. Connector for power supply for head/motor (CN7)
Part number
No.
Signal
: S6B-XH-SM3-TB (J.S.T) or equivalent (board side)
I/O
Contents No.
No.
Signal
I/O
Contents No.
1
+24V
-
Power supply for head
2
+24V
-
Power supply for head
3
+24V
-
Power supply for head
4
GND
-
Ground
5
GND
-
Ground
6
GND
-
Ground
3. Connector for paper near-end sensor detection (CN8)
Part number
No.
1
Signal
+5V
: B2B-PH-SM3-TB (J.S.T) or equivalent (board side)
I/O
-
Contents No.
Power supply for logic
No.
2
Signal
NES
I/O
I
Contents No.
Paper near-end detection signal
5
FTP-627/637DCL / DSL25x
■ COMMANDS
Command
Contents
HT
Moves print position to the next tab.
LF
Line feed.
FF
Feeds forms (new page).
ESC EM+n
Setting the amount of the feeding at automatic paper feed.
ECS RS
Sets reverse printing.
ESC US
Resets reverse printing.
ESC ! + n
Sets print mode.
ESC % + n
External registration character specification/cancellation.
ESC &+y+c1+c2+x+d1~dN
Download character definition.
ESC *+m+n1+n2+d1~dN
Sets bit image mode.
ESC 2
Sets 1/6 inch line feed length.
ESC 3+n
Sets the line feed length.
ESC ? + n
External registration character deletion.
ESC @
Printer initialization.
ESC A+n
Sets the space between the line.
ESC C+n
Sets the page length by character line.
ESC D+d1~dN+NUL
Sets the tab position.
ESC J+n
Feeds paper in forward direction and prints.
ESC K+n
Reverse paper feed.
ESC R +n
International character specification.
ESC V+n
Right rotation 90˚.
ESC X+m+n
Setting the turning time of the motor excitation.
ESC c+1+n
Sets internal processing (including auto paper loading).
ESC d+n
Printing and n-line feeding.
ESC e +n
Prints and reverse feeds n-lines.
ECS s+n
Sets printing speed.
ECS t+n
Character code table selection.
ESC {+n
Sets/resets upside down printing.
6
FTP-627/637DCL / DSL25x
Commands continued
Command
Contents
FS !+n
Kanji printing mode collective specification.
FS &
Kanji printing mode specification.
FS *+m+n1+n2+d1~dN
High speed collective image printing specified.
FS .
Kanji printing mode cancellation.
FS 9+n
Detection function enable/disable setting.
FS C+n
Kanji code system selection.
FS E+n
Correction of impressed energy.
FS W+n
Kanji double height and width mode specification/cancellation.
GS &+m+x+y1+y2+d1~dN
Registration of image data.
GS '+m+n
Prints registered image data.
GS <
Line feeds to the next mark.
GS A+m+n
Sets the line feed length after mark detection.
GS E+n
Sets print quality.
GS V+n+m
Paper cutting (for pending cutter models only).
GS e+n+m
Sets bar code width.
GS h+n
Sets bar code height.
GS k+m+n+d1~dN +NUL
Selects bar code type and prints.
GS w+n
Sets bar code width magnification.
GS a+n
Setting and cancellation of auto status transmission (serial mode only).
FS r+n
Parameter transmission. (Serial Mode only).
7
FTP-627/637DCL / DSL25x
■ OPTIONS
1. Cables
Name
Interface Cable
(between board and
equipment)
Part Number
Length (mm)
For Centronics (CN1) FTP-628Y202
500 (19.7 inches)
For RS232C (CN2)
FTP-628Y302
500 (19.7 inches)
Logic (CN6)
FTP-629Y401
Head / motor (CN7)
FTP-629Y601
Power supply cable
300 (11.8 inches)
2. Paper holder
Name
Part number
Paper Flange
FTP-040HF
Paper Stand
FTP-040HS
Fujitsu Components
International
Headquarter
Offices
Japan
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: promothq@ft.ed.fujitsu.com
Web: www.fcl.fujitsu.com
Europe
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: info@fceu.fujitsu.com
Web: www.fceu.fujitsu.com
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fax: (1-408) 745-4970
Email: marcom@fcai.fujitsu.com
Web: www.fcai.fujitsu.com
Asia Pacific
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#04-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 6375-8560
Fax: (65) 6273-3021
Email: fcal@fcal.fujitsu.com
www.fcal.fujitsu.com
© 2004 Fujitsu Components America, Inc. All company and product names are trademarks or registered
trademarks of their respective owners. Rev. 11/15/2004.
8
Download PDF

advertising