Fujitsu DX80 S2/DX90 S2 Computer Drive User Manual

KD-APD49/KD-PDR40
RECEPTOR CON CD
KD-APD49/KD-PDR40
ESPAÑOL
RÉCEPTEUR CD
KD-APD49/KD-PDR40
FRANÇAIS
ENGLISH
CD RECEIVER
For canceling the display demonstration, see page 6.
Para cancelar la demostración en pantalla, consulte la página 6.
Pour annuler la démonstration des affichages, référez-vous à la page 6.
For installation and connections, refer to the separate manual.
Para la instalación y las conexiones, refiérase al manual separado.
Pour l’installation et les raccordements, se référer au manuel séparé.
INSTRUCTIONS
MANUAL DE INSTRUCCIONES
MANUEL D’INSTRUCTIONS
For customer Use:
Enter below the Model
No. and Serial No. which
are located on the top or
bottom of the cabinet. Retain
this information for future
reference.
Model No.
Serial No.
GET0483-001A
[J]
Cover_KD-APD49[J]f.indd 1
11/1/07 3:11:58 PM
ENGLISH
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best
possible performance from the unit.
INFORMATION (For U.S.A.)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Caution:
Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to
qualified service personnel.
3. CAUTION: (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam.
(For Canada) Visible and/or invisible class 1M laser radiation when open. Do not view directly with
optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
For safety...
[European Union only]
Warning:
If you need to operate the unit while driving, be
sure to look around carefully or you may be involved
in a traffic accident.
• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
• Stop the car before performing any complicated
operations.
Temperature inside the car...
If you have parked the car for a long time in hot or cold
weather, wait until the temperature in the car becomes
normal before operating the unit.
2
EN02-05_KD-APD49[J]f.indd 2
11/1/07 3:11:13 PM
CONTENTS
Control panel — KD-APD49/KD-PDR40 ... 4
Remote controller — RM-RK50........... 5
Getting started ................................ 6
ENGLISH
How to reset your unit
Basic operations ................................................... 6
• Your preset adjustments will also be erased.
How to forcibly eject a disc
• Be careful not to drop the disc when it ejects.
• If this does not work, reset your unit.
How to use the M MODE button
If you press M MODE, the unit goes into functions mode,
then the number buttons and 5/∞ buttons will work
as different function buttons.
Ex.: When number button 2 works as
MO (monaural) button.
Radio operations ............................. 7
Disc operations ................................ 8
Playing a disc in the unit ..................................... 8
iPod operations ...............................
Sound adjustments ..........................
General settings — PSM ..................
Other external component
operations ...................................
Title assignment..............................
Maintenance ...................................
More about this unit ........................
Troubleshooting ..............................
Specifications ..................................
10
12
14
16
16
17
17
20
22
The control panel illustrations used for explanation
in this manual is of KD-APD49.
Detaching the control panel
To use these buttons for their original functions
again after pressing M MODE, press M MODE again.
• Waiting for about 5 seconds without pressing any of
these buttons will automatically cancels the functions
mode.
KD-APD49 is equipped with the steering wheel
remote control function.
• See the Installation/Connection Manual (separate
volume) for connection.
Attaching the control panel
3
EN02-05_KD-APD49[J]f.indd 3
11/1/07 3:11:15 PM
ENGLISH
Control panel — KD-APD49 / KD-PDR40
Parts identification
Display window
1
2
3
4
5
6
7
8
9
p
q
w
e
r
t
y
u
i
5 (up) / ∞ (down) buttons
0 (eject) button
(standby/on attenuator) button
Control dial
Remote sensor
DO NOT expose the remote sensor to strong light
(direct sunlight or artificial lighting).
BAND button
Loading slot
Display window
EQ (equalizer) button
DISP (display) button
(control panel release) button
i (iPod) button
4 /¢ buttons
SRC (source) button
SEL (select) button
M MODE button
MO (monaural) button
SSM (Strong-station Sequential Memory) button
o
;
a
s
d
f
g
h
j
k
l
/
z
x
Number buttons
RPT (repeat) button
RND (random) button
AUX (auxiliary) input jack
Source display / Track number / Folder number /
Time countdown indicator
Tr (track) indicator
DISC indicator
Playback mode / item indicators— RND (random),
(disc), (folder), RPT (repeat)
Tuner reception indicators—ST (stereo),
MO (monaural)
Sound mode (iEQ: intelligent equalizer) indicators
—CLASSIC, HIP HOP, JAZZ, ROCK, POPS, USER
LOUD (loudness) indicator
EQ (equalizer) indicator
Disc information indicators—
TAG (Tag information), (folder), (track/file)
Main display
4
EN02-05_KD-APD49[J]f.indd 4
11/1/07 3:11:16 PM
Remote controller — RM-RK50
ENGLISH
Main elements and features
Installing the lithium coin battery
(CR2025)
1
For USA-California Only:
This product contains a CR Coin Cell Lithium Battery
which contains Perchlorate Material—special
handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
2
Aim the remote controller directly at the remote
sensor on the unit. Make sure there is no obstacle
in between.
Warning:
• Do not install any battery other than CR2025 or its
equivalent; otherwise, it may explode.
• Do not leave the remote controller in a place
(such as the dashboard) exposed to direct
sunlight for a long time; otherwise, it may
explode.
• Store the battery in a place where children cannot
reach to avoid the risk of accidents.
• To prevent the battery from over-heating,
cracking, or starting a fire:
– Do not recharge, short, disassemble, heat the
battery, or dispose of it in a fire.
– Do not leave the battery with other metallic
materials.
– Do not poke the battery with tweezers or
similar tools.
– Wrap the battery with tape and insulate when
throwing away or saving it.
3
4
5
6
(standby/on/attenuator) button
• Turns the power on if pressed briefly or
attenuates the sound when the power is on.
• Turns the power off if pressed and held.
5 U (up) / D (down) ∞ buttons
• Changes the FM/AM bands with 5 U.
• Changes the preset stations with D ∞.
• Changes the folder of the MP3/WMA discs.
• While listening to an Apple iPod.
– Enters the main menu if pressed and held.
(Now 5 U/D ∞/2 R/F 3 work as the menu
selecting buttons.)
• While listening to an iPod (in menu selecting
mode):
– Returns to the previous menu if pressed 5 U
briefly.
– Selects an item if pressed D ∞ briefly. (Then,
press and hold D ∞ to play back the selection
directly.)
VOL – / VOL + buttons
• Adjusts the volume level.
SOUND button
• Selects the sound mode (iEQ: intelligent equalizer).
SOURCE button
• Selects the source.
2 R (reverse) / F (forward) 3 buttons
• Searches for stations if pressed briefly.
• Fast-forwards or reverses the track if pressed and
held.
• Changes the track if pressed briefly.
• While listening to an iPod (in menu selecting
mode):
– Accelerated file search: Hold 2 R/F 3 to fast
skip during song search in the main menu.
5
EN02-05_KD-APD49[J]f.indd 5
11/20/07 10:20:29 AM
ENGLISH
Getting started
Basic operations
~
Turn on the power.
To drop the volume in a
moment (ATT)
To restore the sound, press
the button again.
To turn off the power
Ÿ
Basic settings
• See also “General settings — PSM” on pages
14 and 15.
1
*1 You cannot select “CD” as the playback source
if there is no disc in the unit.
*2 “NO IPOD” appears if an iPod is not connected.
!
2
1 Canceling the display demonstrations
For FM/AM tuner
Select “DEMO,” then “DEMO OFF.”
2 Setting the clock
⁄
Select “CLOCK HOUR,” then adjust the hour.
Select “CLOCK MIN” (minute), then adjust the
minute.
Adjust the volume.
3
Volume level appears.
@
Adjust the sound as you want. (See
pages 12 and 13.)
Finish the procedure.
To check the current clock time while the
power is turned off
Clock time is shown on the display for
about 5 seconds. See also page 14.
Caution on volume setting:
Discs produce very little noise compared with other
sources. Lower the volume before playing a disc
to avoid damaging the speakers by the sudden
increase of the output level.
6
EN06-13_KD-APD49[J]f.indd 6
11/1/07 3:11:26 PM
When an FM stereo broadcast is hard to
receive
~
Lights up when monaural mode is activated.
ENGLISH
Radio operations
Ÿ
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
!
Reception improves, but the stereo effect will be lost.
To restore the stereo effect, repeat the same
procedure. “MONO OFF” appears and the MO indicator
goes off.
Start searching for a station.
Storing stations in memory
You can preset six stations for each band.
When a station is received, searching stops.
To stop searching, press the same button
again.
FM station automatic presetting—
SSM (Strong-station Sequential
Memory)
1
To tune in to a station manually
Select the FM band (FM1 – FM3) you want to
store into.
In step ! above...
1
2
3
2 Select a desired station frequency.
“SSM” flashes, then disappears when automatic
presetting is over.
Local FM stations with the strongest signals are
searched and stored automatically in the FM band.
7
EN06-13_KD-APD49[J]f.indd 7
11/1/07 3:11:28 PM
ENGLISH
Manual presetting
Ex.: Storing the FM station of 92.50MHz into preset
number 4 of the FM1 band.
1
Disc operations
Playing a disc in the unit
All tracks will be played repeatedly until you change the
source or eject the disc.
2
3
To stop play and eject the disc
Preset number flashes for a while.
Listening to a preset station
1
2
• Press SRC to listen to another
playback source.
[Hold] To fast-forward or reverse the
track
Select the preset station (1 – 6) you want.
[Press] To go to the next or previous
track
or
[Press] To go to the next or previous
folder (only for MP3 or WMA
discs)
To locate a particular track (for CD) or folder
(for MP3 or WMA discs) directly
To check other information while listening
to the radio
Frequency = Clock =
Station name * = (back to the
beginning)
To select a number from 01 – 06:
To select a number from 07 – 12:
* If no title is assigned to a station, “NO NAME” appears.
To assign a title to a station, see page 16.
8
EN06-13_KD-APD49[J]f.indd 8
11/1/07 3:11:29 PM
To select a particular track in a folder
(for MP3 or WMA discs):
Changing the display information
While playing an audio CD or CD Text
ENGLISH
• To use direct folder access on MP3/WMA discs, it
is required that folders are assigned with 2-digit
numbers at the beginning of their folder names—
01, 02, 03, and so on.
A = B = Disc title/performer *1 = Track
title *1 [ ] = (back to the beginning)
Other main functions
Skipping tracks quickly during play
• For MP3 or WMA discs, you can skip tracks within the
same folder.
Ex.: To select track 32 while playing a track whose
number is a single digit (1 to 9)
While playing an MP3 or a WMA track
• When “TAG DISPLAY” is set to “TAG ON”
(see page 15)
A = B = Album name/performer (folder
name *2) [
] = Track title (file
name *2) [
] = (back to the beginning)
• When “TAG DISPLAY” is set to “TAG OFF”
1
A = B = Folder name [ ] = File name
[ ] = (back to the beginning)
2
Each time you press the button, you can skip 10
tracks.
• After the last track, the first track will be selected
and vice versa.
3
A : Current track number with the elapsed playing
time
B : Current track number with the clock time
[ ] : Corresponding indicator lights up on the display.
*1 If the current disc is an audio CD, “NO NAME” appears.
*2 If an MP3/WMA file does not have Tag information,
folder name and file name appear. In this case, the
TAG indicator will not light up.
Prohibiting disc ejection
You can lock a disc in the loading slot.
“EJECT LOCK” flashes on the display.
To cancel the prohibition, repeat the same
procedure.
9
EN06-13_KD-APD49[J]f.indd 9
11/1/07 3:11:30 PM
ENGLISH
Selecting the playback modes
You can use only one of the following playback modes
at a time.
1
2
Select your desired playback mode.
iPod operations
You can play songs in an Apple iPod by connecting it
with the supplied direct connection cable for iPod.
You can control playback from the unit or from your
iPod.
• Disconnecting the iPod will stop playback. Press SRC
to listen to another playback source.
Caution:
7 Repeat play
Mode
Plays repeatedly
]
TRACK RPT : The current track. [
FOLDER RPT * : All tracks of the current folder.
[
]
RPT OFF
: Cancels.
7 Random play
Mode
Plays at random
• Avoid using the iPod if it might hinder your safety
while driving.
• Make sure all important data has been backed up
to avoid losing the data.
• For connection, see the Installation/Connection
Manual (separate volume).
• For details, refer also to the manual supplied for your
iPod.
~
Connect an iPod.
Direct connection
cable for iPod
FOLDER RND *: All tracks of the current folder,
then the tracks of the next folder
and so on. [
]
ALL RND
: All tracks of the current disc.
[
]
RND OFF
: Cancels.
* Only while playing an MP3 or a WMA disc.
If an iPod has been connected...
To directly select “IPOD” as the source
while listening to another source or
when the power is turned off.
[ ] : Corresponding indicator lights up on the
display.
Playback starts automatically from where it had
been paused previously.
Ÿ
Adjust the volume.
10
EN06-13_KD-APD49[J]f.indd 10
11/1/07 3:11:31 PM
Adjust the sound as you want. (See
pages 12 and 13.)
Selecting a track from the menu
1
To control playback from your iPod
Enter the main menu.
or
“IPOD MODE” appears on the
display.
• Press and hold this button again to control playback
from the unit. “HEAD MODE” appears on the display.
ENGLISH
!
Now the 5/∞/4 /¢ /number
buttons work as the menu selecting buttons.
2
Select the desired menu.
Playback control from the unit
[Press] Go to the next or previous
track
PLAYLIST Ô ARTIST Ô ALBUM Ô SONG
Ô PODCASTÔ GENRE Ô COMPOSER
Ô AUDIOBOOK Ô (back to the beginning)
[Hold] Fast-forward or reverse the
track during playback
Fast-skip the menu items of
the main menu
[Hold] Enter the main menu (see the
right column).
[Press] Pause/resume playback.
[Press] Go to the top menu of “PLAYLIST,” “ARTIST,”
“ALBUM,” “SONG,” “PODCAST,” or “GENRE” in
the main menu (see the right column).
• Pressing the number buttons can directly select
the desired menu (see the left column for
details).
3
Confirm the selection.
To move back to the previous
menu, press 5.
• Holding the button will start play back the
selected item directly.
• If a track is selected, playback starts
automatically.
• If the selected item has another layer, you will
enter the layer. Repeat steps 2 and 3 until the
desired track is played.
• Accelerated file search: Hold 4 /¢
to fast skip during song search in the main menu.
[Hold] Go to the top menu of “COMPOSER” or
“AUDIOBOOK” in the main menu (see the
right column).
Continued on the next page
11
EN06-13_KD-APD49[J]f.indd 11
11/20/07 10:24:03 AM
ENGLISH
To exit from menu selecting mode
To check other information while listening
to an iPod
or
* The menu selecting mode will be canceled:
– If no operations are performed for about
10 seconds.
– When you confirm the selection of a track.
– Pressing some other buttons such as DISP, SEL,
MODE, or EQ.
Current track number with the elapsed
playing time = Current track number with
the clock time = Track title * = Album name/
performer * = (back to the beginning)
* When “TAG DISPLAY” is set to “TAG OFF” (see page 15),
file name and folder name appear.
Selecting the playback modes
1
2
Sound adjustments
You can select a preset sound mode suitable to the
music genre (iEQ: intelligent equalizer).
Select your desired playback mode.
7 Repeat play
Mode
ONE RPT
ALL RPT
RPT OFF
Playback functions (as on iPod)
: Same as “Repeat One.” [
: Same as “Repeat All.” [
: Cancels.
Adjusting the sound
]
]
You can adjust the sound characteristics to your
preference.
• The adjustment you make will be stored for the
currently selected sound mode (iEQ) including
“USER.”
7 Random play
Mode
Playback functions (as on iPod)
SONG RND : Same as “Shuffle Songs.” [
ALBUM RND * : Same as “Shuffle Albums.”
[
]
RND OFF
: Cancels.
]
1
2
* Functions only if you select “ALL” in “ALBUMS” of
the main menu.
[ ] : Corresponding indicator lights up on the
display.
Indication, [Range]
FADER *2, [R06 to F06]
Adjust the front and rear speaker balance.
BALANCE *3, [L06 to R06]
Adjust the left and right speaker balance.
12
EN06-13_KD-APD49[J]f.indd 12
11/20/07 11:49:09 AM
3
Select a sound characteristic.
4
Adjust the sound elements of the selected
sound characteristic.
1 Adjust the frequency.
LOUD *4 (loudness), [LOUD ON or LOUD OFF]
Boost low and high frequencies to produce a
well-balanced sound at a low volume level.
SUBWOOFER *1, [00 to 08, initial: 04]
Adjust the subwoofer output level.
VOL ADJ (volume adjust), [–05 to +05, initial: 00]
Adjust the volume level of each source (except FM), in
relation to the FM volume level. The volume level will
automatically increase or decrease when you change
the source.
• Before making an adjustment, select the source you
want to adjust.
ENGLISH
Indication, [Range]
2 Adjust the level.
VOLUME, [00 to 50 or 00 to 30 ]*5
Adjust the volume.
3 Adjust the quality slope (Q).
*1 Displayed only when “L/O MODE” is set to “SUB.W”
(see page 15).
*2 If you are using a two-speaker system, set the fader
level to “00.”
*3 This adjustment will not affect the subwoofer output.
*4 The adjustment made (LOUD ON/LOUD OFF) will be
applied to all sound modes.
*5 Depending on the amplifier gain control setting. (See
page 15 for details.)
Sound
elements
Range/selectable items
BASS
MID
TRE
Frequency
60 Hz
80 Hz
100 Hz
120 Hz
500 Hz
1.0 kHz
1.5 kHz
2.5 kHz
7.5 kHz
10.0 kHz
12.5 kHz
15.0 kHz
You can adjust the sound modes and store your own
adjustments in memory.
Level
–06 to
+06
–06 to
+06
–06 to
+06
1
Select a sound mode.
Q (Q-slope)
Q0.5
Q1.0
Q1.5
Q2.0
Q0.75
Q1.0
Q1.25
Q1.5
Q0.75
Q1.25
2
Enter the adjustment mode.
• If no operation is done within
5 seconds, this mode is canceled.
BASS: Bass MID: Mid-range TRE: Treble
Storing your own sound mode
5
The adjustment made will be stored
automatically. Repeat steps 3 and 4 to adjust
other sound characteristics.
13
EN06-13_KD-APD49[J]f.indd 13
11/20/07 10:24:06 AM
ENGLISH
General settings — PSM
You can change PSM (Preferred Setting Mode) items
listed in the table below and on page 15.
3
Adjust the PSM item selected.
4
Repeat steps 2 and 3 to adjust other PSM
items if necessary.
5
Finish the procedure.
1
2
Select a PSM item.
Indications
Item
( : Initial)
Setting, [reference page]
DEMO
Display
demonstration
• DEMO ON
: The display demonstration will be activated automatically if no
operation is done for about 20 seconds, [6].
: Cancels.
CLOCK DISP *
Clock display
• CLOCK ON
1
• DEMO OFF
• CLOCK OFF
: The clock time is shown on the display at all times when the power is
turned off.
: Cancels; pressing DISP will show the clock time for about 5 seconds
when the power is turned off, [6].
CLOCK HOUR
Hour adjustment
1 – 12
[Initial: 1 (1:00)], [6].
CLOCK MIN
Minute adjustment
00 – 59
[Initial: 00 (1:00)], [6].
DIMMER
Dimmer
• ON
• OFF
: Dims the display and button illumination.
: Cancels.
*1 If the power supply is not interrupted by turning off the ignition key of your car, it is recommended that you select
“CLOCK OFF” to save the car’s battery.
14
EN14-23_KD-APD49[J]f.indd 14
11/1/07 3:11:43 PM
Item
( : Initial)
Setting, [reference page]
AUDIOBOOKS *2
Speed control of
“Audiobook”
• NORMAL
• FASTER
• SLOWER
: You can select the playback speed of the “Audiobook” sound file in
your iPod.
SCROLL *3
Scroll
• ONCE
• AUTO
• OFF
:
:
:
•
L/O MODE
Line output mode
• REAR
: Select if the REAR LINE OUT terminals are used for connecting the
speakers (through an external amplifier).
: Select if the REAR LINE OUT terminals are used for connecting a
subwoofer (through an external amplifier).
• SUB.W
ENGLISH
Indications
Scrolls the displayed information once.
Repeats scrolling (at 5-second intervals).
Cancels.
Pressing DISP for more than one second can scroll the display
regardless of the setting.
SUB.W FREQ *4
Subwoofer cutoff
frequency
• LOW
• MID
• HIGH
: Frequencies lower than 90 Hz are sent to the subwoofer.
: Frequencies lower than 135 Hz are sent to the subwoofer.
: Frequencies lower than 180 Hz are sent to the subwoofer.
TAG DISPLAY
Tag display
• TAG ON
• TAG OFF
: Shows the Tag information while playing MP3/WMA tracks, [9].
: Cancels.
AMP GAIN
Amplifier gain
control
• LOW POWER
IF BAND
Intermediate
frequency band
• AUTO
AREA
Tuner channel
interval
• AREA US
: VOLUME 00 – VOLUME 30. (Select this if the maximum power of the
speaker is less than 50 W to avoid damaging the speaker.)
• HIGH POWER : VOLUME 00 – VOLUME 50.
• WIDE
• AREA EU
• AREA SA
: Increases the tuner selectivity to reduce interference noise between
close stations. (The stereo effect may be lost.)
: Subject to interference noise from adjacent stations, but the sound
quality will not be degraded and the stereo effect will remain.
: When using in North/Central/South America. AM/FM intervals are
set to 10 kHz/200 kHz.
: When using in any other areas. AM/FM intervals are set to 9 kHz/
50 kHz (100 kHz during auto search).
: When using in South American countries where FM interval is
100 kHz. AM interval is set to 10 kHz.
*2 Displayed only when an iPod is connected and playback is controlled from the unit.
*3 Some characters or symbols will not be shown correctly (or will be blanked) on the display.
*4 Displayed only when “L/O MODE” is set to “SUB.W.”
15
EN14-23_KD-APD49[J]f.indd 15
11/1/07 3:11:45 PM
ENGLISH
Other external component
operations
You can connect an external component to the AUX
(auxiliary) input jack on the control panel.
Title assignment
You can assign names to 30 station frequencies (FM and
AM) and up to 8 characters for each station name.
1
Select FM/AM.
2
Show the title entry screen.
3
Assign a title.
1 Select a character.
Portable audio player, etc.
3.5 mm stereo mini
plug (not supplied)
~
Ÿ
!
Turn on the connected component and
start playing the source.
Adjust the volume.
2 Move to the next (or previous) character
position.
⁄
Adjust the sound as you want. (See
pages 12 and 13.)
3 Repeat steps 1 and 2 until you finish
entering the title.
To check other information while listening
to an external component
Clock Ô AUX IN
4
Finish the procedure.
To erase the entire title
In step 2 above...
16
EN14-23_KD-APD49[J]f.indd 16
11/1/07 3:11:46 PM
How to clean the connectors
Frequent detachment will deteriorate the connectors.
To minimize this possibility, periodically wipe the
connectors with a cotton swab or cloth moistened with
alcohol, being careful not to damage the connectors.
To play new discs
New discs may have some rough spots
around the inner and outer edges. If
such a disc is used, this unit may reject
the disc.
To remove these rough spots, rub the edges with a
pencil or ball-point pen, etc.
ENGLISH
Maintenance
Do not use the following discs:
Single CD
—8 cm (3-3/16”) disc
Warped disc
Sticker and
sticker residue
Stick-on label
Connectors
Moisture condensation
Moisture may condense on the lens inside the unit in
the following cases:
• After starting the heater in the car.
• If it becomes very humid inside the car.
Should this occur, the unit may malfunction. In this
case, eject the disc and leave the unit turned on for a
few hours until the moisture has evaporated.
Unusual shape
How to handle discs
Center holder
When removing a disc from its
case, press down the center holder
of the case and lift the disc out,
holding it by the edges.
• Always hold the disc by the edges. Do not touch its
recording surface.
When storing a disc in its case, gently insert the
disc around the center holder (with the printed surface
facing up).
• Make sure to store discs in cases after use.
To keep discs clean
A dirty disc may not play correctly.
If a disc does become dirty, wipe it with
a soft cloth in a straight line from center
to edge.
• Do not use any solvents (for example, conventional
record cleaner, spray, thinner, benzine, etc.) to clean
discs.
More about this unit
Basic operations
Turning on the power
• By pressing SRC (source) or i (iPod) button on the
unit, you can also turn on the power. If the source is
ready, playback also starts.
Turning off the power
• If you turn off the power while listening to a track,
playback will start from where it had been stopped
previously next time you turn on the power.
Continued on the next page
17
EN14-23_KD-APD49[J]f.indd 17
11/1/07 3:11:47 PM
ENGLISH
General
Playing a CD-R or CD-RW
• If you change the source while listening to a disc or
an iPod, playback stops.
Next time you select “CD” or “IPOD” as the playback
source, playback will start from where it had been
stopped/paused previously.
• After ejecting a disc or disconnecting an iPod,
“NO DISC” or “NO IPOD” appears and you cannot
operate some of the buttons. Insert another disc,
connect an iPod, or press SRC to select another
playback source.
• Use only “finalized” CD-Rs or CD-RWs.
• This unit can only play back files of the same type as
those which are detected first if a disc includes both
audio CD (CD-DA) files and MP3/WMA files.
• This unit can play back multi-session discs; however,
unclosed sessions will be skipped while playing.
• Some CD-Rs or CD-RWs may not play back on this
unit because of their disc characteristics, or for the
following reasons:
– Discs are dirty or scratched.
– Moisture condensation has occurred on the lens
inside the unit.
– The pickup lens inside the unit is dirty.
– The files on the CD-R/CD-RW are written using the
“Packet Write” method.
– There are improper recording conditions (missing
data, etc.) or media conditions (stained, scratched,
warped, etc.).
• CD-RWs may require a longer readout time since the
reflectance of CD-RWs is lower than that of regular CDs.
• Do not use the following CD-Rs or CD-RWs:
– Discs with stickers, labels, or a protective seal stuck
to the surface.
– Discs on which labels can be directly printed by an
ink jet printer.
Using these discs under high temperature or high
humidity may cause malfunctions or damage to the
unit.
Tuner operations
Storing stations in memory
• During SSM search...
– All previously stored stations are erased and the
stations are stored anew.
– Received stations are preset in No. 1 (lowest
frequency) to No. 6 (highest frequency).
– When SSM is over, the station stored in No. 1 will
be automatically tuned in.
• When storing a station manually, the previously
preset station is erased when a new station is stored
in the same preset number.
Disc operations
Caution for DualDisc playback
• The Non-DVD side of a “DualDisc” does not comply
with the “Compact Disc Digital Audio” standard.
Therefore, the use of Non-DVD side of a DualDisc on
this product may not be recommended.
General
• This unit has been designed to reproduce
CDs/CD Texts, and CD-Rs (Recordable)/CD-RWs
(Rewritable) in audio CD (CD-DA), MP3 and WMA
formats.
• When a disc is inserted upside down, “PLEASE” and
“EJECT” appear alternately on the display. Press 0 to
eject the disc.
• MP3 and WMA “tracks” (words “file” and “track” are
used interchangeably) are recorded in “folders.”
• While fast-forwarding or reversing on an MP3 or
WMA disc, you can only hear intermittent sounds.
Playing an MP3/WMA disc
• This unit can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of
the letter case—upper/lower).
• This unit can show the names of albums, artists
(performer), and Tag (Version 1.0, 1.1, 2.2, 2.3, or
2.4) for MP3 files and for WMA files.
• This unit can display only one-byte characters. No
other characters can be correctly displayed.
• This unit can play back MP3/WMA files meeting the
conditions below:
– Bit rate: 8 kbps — 320 kbps
– Sampling frequency:
48 kHz, 44.1 kHz, 32 kHz (for MPEG-1)
24 kHz, 22.05 kHz, 16 kHz (for MPEG-2)
18
EN14-23_KD-APD49[J]f.indd 18
11/2/07 3:11:46 PM
•
•
•
•
Ejecting a disc
• If the ejected disc is not removed within 15 seconds,
it is automatically inserted into the loading slot again
to protect it from dust. Playback starts automatically.
iPod operations
• Controllable iPod:
– iPod mini
– iPod G4
– iPod photo
– iPod nano (1st & 2nd Generation)
– iPod with video (5th Generation)
• Update your iPod to the latest software version
before using it with this unit.
• When you turn on this unit, the iPod is charged
through this unit.
• While connecting an iPod with Video:
– No video shows on the iPod’s display or the
external monitor (only the audio part is available).
– It is not possible to browse video files on the
“Video“ menu. (If you connect the iPod during
the playback or pausing of a video file, resuming
playback will not work.)
• iPod shuffle cannot be used with this unit.
• You can control the iPod from this unit when “JVC” or
“ ” appears on the iPod display after connection.
• The song order displayed on the selection menu of
this unit may differ from that of the iPod.
• If playback is stopped, select a track from the
selection menu or press BAND to playback the same
track again.
• The text information may not be displayed correctly:
– Some characters such as accented letters cannot be
shown correctly on the display.
– Communication between the iPod and the unit is
not stable.
• If the text information includes more than
11 characters, it scrolls on the display. This unit can
display up to 64 characters.
ENGLISH
•
– Disc format: ISO 9660 Level 1/Level 2, Romeo,
Joliet, Windows long file name
The maximum number of characters for file/folder
names vary depending on the disc format used
(includes 4 extension characters—<.mp3> or
<.wma>).
– ISO 9660 Level 1: up to 12 characters
– ISO 9660 Level 2: up to 31 characters
– Romeo: up to 128 characters
– Joliet: up to 64 characters
– Windows long file name: up to 128 characters
This unit can recognize a total of 512 files,
255 folders, and 8 hierarchical levels.
This unit can play back files recorded in VBR (variable
bit rate).
Files recorded in VBR have a discrepancy in the
elapsed time display, and do not show the actual
elapsed time. In particular, this difference becomes
noticeable after performing the search function.
This unit cannot play back the following files:
– MP3 files encoded in MP3i and MP3 PRO format.
– MP3 files encoded in an inappropriate format.
– MP3 files encoded with Layer 1/2.
– WMA files encoded in lossless, professional, and
voice format.
– WMA files which are not based upon Windows
Media® Audio.
– WMA files copy-protected with DRM.
– Files which have data such as AIFF, ATRAC3, etc.
The search function works but search speed is not
constant.
Notice:
When operating an iPod, some operations may not
be performed correctly or as intended. In this case,
visit the following JVC web site:
<http://www.jvc-victor.co.jp/english/car/>
General settings—PSM
• If you change the “AMP GAIN” setting from
“HIGH POWER” to “LOW POWER” while the
volume level is set higher than “VOLUME 30,” the
unit automatically changes the volume level to
“VOLUME 30.”
Continued on the next page
19
EN14-23_KD-APD49[J]f.indd 19
11/13/07 4:37:20 PM
ENGLISH
Preset value setting for each sound mode
Preset value
Sound mode
USER
ROCK
CLASSIC
POP
HIP HOP
JAZZ
BASS (bass)
Freq. Level
60 Hz
00
100 Hz
+03
80 Hz
+01
100 Hz
+02
60 Hz
+04
80 Hz
+03
MID (mid-range)
Q
Q1.0
Q1.0
Q1.0
Q1.0
Q1.0
Q1.0
Freq. Level
1.0 kHz
00
1.0 kHz
00
1.0 kHz
00
1.0 kHz
+01
1.0 kHz
–02
1.0 kHz
00
Q
Q1.25
Q1.25
Q1.25
Q1.25
Q1.0
Q1.25
TRE (treble)
Freq. Level
7.5 kHz
00
10.0 kHz
+02
10.0 kHz
+03
10.0 kHz
+02
10.0 kHz
+01
10.0 kHz
+03
LOUD
(loudness)
Q
Q1.25
Q1.25
Q1.25
OFF
Q1.25
Q1.25
Q1.25
Freq.: Frequency Q: Q-slope
Troubleshooting
What appears to be trouble is not always serious. Check the following points before calling a service center.
FM/AM
General
Symptoms
Remedies/Causes
• Sound cannot be heard from the speakers.
• Adjust the volume to the optimum level.
• Check the cords and connections.
• The unit does not work at all.
Reset the unit (see page 3).
• SSM automatic presetting does not work.
Store stations manually.
• Static noise while listening to the radio.
Connect the antenna firmly.
• Disc cannot be played back.
Insert the disc correctly.
Disc playback
• CD-R/CD-RW cannot be played back.
• Insert a finalized CD-R/CD-RW.
• Tracks on the CD-R/CD-RW cannot be skipped. • Finalize the CD-R/CD-RW with the component which
you used for recording.
• Disc can neither be played back nor ejected.
• Unlock the disc (see page 9).
• Eject the disc forcibly (see page 3).
• Disc sound is sometimes interrupted.
• Stop playback while driving on rough roads.
• Change the disc.
• Check the cords and connections.
• “NO DISC” appears on the display.
• “PLEASE” and “EJECT“ appear alternately on
the display.
Insert a playable disc into the loading slot.
20
EN14-23_KD-APD49[J]f.indd 20
11/1/07 3:11:50 PM
MP3/WMA playback
Remedies/Causes
• Disc cannot be played back.
• Use a disc with MP3/WMA tracks recorded in a format
compliant with ISO 9660 Level 1, Level 2, Romeo, or
Joliet.
• Add the extension code <.mp3> or <.wma> to the
file names.
• Noise is generated.
Skip to another track or change the disc. (Do not add the
extension code <.mp3> or <.wma> to non-MP3 or
WMA tracks.)
ENGLISH
Symptoms
• A longer readout time is required (“READING” Do not use too many hierarchical levels and folders.
keeps flashing on the display).
• Tracks do not play back in the order you have The playback order is determined when the files are
intended them to play.
recorded.
• The elapsed playing time is not correct.
This sometimes occurs during playback. This is caused by
how the tracks are recorded on the disc.
iPod playback
• The correct characters are not displayed (e.g. This unit can only display letters (upper case), numbers,
album name).
and a limited number of symbols.
• The iPod does not turn on or does not work.
• Check the connecting cable and its connection.
• Update the firmware version.
• Charge the battery.
• The sound is distorted.
Deactivate the equalizer either on the unit or the iPod.
• “NO IPOD” appears on the display.
• Check the connecting cable and its connection.
• Charge the battery.
• Playback stops.
The headphones are disconnected during playback. Turn
off the unit’s power and turn it on again.
• No sound can be heard when connecting an
iPod nano.
• Disconnect the headphones from the iPod nano.
• Update the firmware version of the iPod nano.
• “NO FILES” appears on the display.
No tracks are stored. Import tracks to the iPod.
• The iPod’s controls do not work after
disconnecting from this unit.
Reset the iPod.
• “CANNOT PLAY” appears on the display.
Communication error occurs.
Disconnect and connect the cable to the iPod again.
21
EN14-23_KD-APD49[J]f.indd 21
11/13/07 10:57:32 AM
ENGLISH
Specifications
AUDIO AMPLIFIER SECTION
Power Output:
20 W RMS × 4 Channels at 4 Ω
and ≤ 1% THD+N
Signal-to-Noise Ratio:
80 dBA (reference: 1 W into 4 Ω)
Load Impedance:
4 Ω (4 Ω to 8 Ω allowance)
Tone Control Range:
Bass:
±12 dB (60 Hz, 80 Hz, 100 Hz, 120 Hz)
Mid-range:
±12 dB (500 Hz, 1 kHz, 1.5 kHz, 2.5 kHz)
Treble:
±12 dB (7.5 kHz, 10 kHz, 12.5 kHz, 15 kHz)
Q (Q-slope):
Q0.5 to Q2.0
Frequency Response:
40 Hz to 20 000 Hz
Line-Out Level/Impedance:
Subwoofer-Out Level/Impedance:
KD-APD49:
5.0 V/20 kΩ load (full scale)
KD-PDR40:
2.5 V/20 kΩ load (full scale)
KD-APD49:
5.0 V /20 kΩ load (full scale)
KD-PDR40:
2.5 V/20 kΩ load (full scale)
Output Impedance:
1 kΩ
Other Terminal:
AUX (auxiliary) input jack, iPod connector,
Steering wheel remote input (only for
KD-APD49)
TUNER SECTION
Frequency Range:
FM:
with channel interval set to 100 kHz 87.5 MHz to 107.9 MHz
or 200 kHz
with channel interval set to 50 kHz
AM: with channel interval set to 10 kHz
with channel interval set to 9 kHz
FM Tuner
AM Tuner
87.5 MHz to 108.0 MHz
530 kHz to 1 710 kHz
531 kHz to 1 602 kHz
Usable Sensitivity:
11.3 dBf (1.0 μV/75 Ω)
50 dB Quieting Sensitivity:
16.3 dBf (1.8 μV/75 Ω)
Alternate Channel Selectivity (400 kHz):
65 dB
Frequency Response:
40 Hz to 15 000 Hz
Stereo Separation:
35 dB
Sensitivity:
20 μV
Selectivity:
35 dB
22
EN14-23_KD-APD49[J]f.indd 22
11/20/07 10:25:12 AM
Type:
Compact disc player
Signal Detection System:
Non-contact optical pickup
(semiconductor laser)
Number of Channels:
2 channels (stereo)
Frequency Response:
5 Hz to 20 000 Hz
Dynamic Range:
96 dB
Signal-to-Noise Ratio:
98 dB
Wow and Flutter:
Less than measurable limit
MP3 Decoding Format:
(MPEG1/2 Audio Layer 3)
Max. Bit Rate:
320 kbps
WMA (Windows Media® Audio)
Decoding Format:
Max. Bit Rate:
320 kbps
ENGLISH
CD PLAYER SECTION
GENERAL
Power Requirement:
Operating Voltage:
DC 14.4 V (11 V to 16 V allowance)
Grounding System:
Negative ground
Allowable Operating Temperature:
0°C to +40°C (32°F to 104°F)
Dimensions (W × H × D): (approx.) Installation Size:
182 mm × 52 mm × 160 mm
(7-3/16” × 2-1/16” × 6-5/16”)
Panel Size:
Mass:
188 mm × 58 mm × 6 mm
(7-7/16” × 2-5/16” × 1/4”)
1.3 kg (2.9 lbs) (excluding accessories)
Design and specifications are subject to change without notice.
If a kit is necessary for your car, consult your telephone directory for the nearest car audio speciality shop.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
• iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
23
EN14-23_KD-APD49[J]f.indd 23
11/13/07 11:05:19 AM
Having TROUBLE with operation?
Please reset your unit
Refer to page of How to reset your unit
Still having trouble??
USA ONLY
Call 1-800-252-5722
http://www.jvc.com
We can help you!
EN, SP, FR
© 2007 Victor Company of Japan, Limited
Rear_KD-APD49[J]f.indd 2
1107DTSMDTJEIN
11/1/07 3:12:26 PM
KD-APD49/KD-PDR40
Installation/Connection Manual
Manual de instalación/conexión
Manuel d’installation/raccordement
GET0483-002A
1107DTSMDTJEIN
[J]
EN, SP, FR
© 2007 Victor Company of Japan, Limited
ENGLISH
ESPAÑOL
FRANÇAIS
This unit is designed to operate on 12 V DC, NEGATIVE ground
electrical systems. If your vehicle does not have this system, a
voltage inverter is required, which can be purchased at JVC car audio
dealers.
Esta unidad está diseñada para funcionar con 12 V de CC, con
sistemas eléctricos de masa NEGATIVA. Si su vehículo no posee
este sistema, será necesario un inversor de tensión, que puede ser
adquirido en los concesionarios de JVC de equipos de audio para
automóviles.
Cet appareil est conçu pour fonctionner sur des sources de courant
continu de 12 V à masse NEGATIVE. Si votre véhicule n’offre pas ce
type d’alimentation, il vous faut un convertisseur de tension, que vous
pouvez acheter chez un revendeur d’autoradios JVC.
WARNINGS
ADVERTENCIAS
AVERTISSEMENTS
To prevent short circuits, we recommend that you disconnect the
battery’s negative terminal and make all electrical connections before
installing the unit.
• Be sure to ground this unit to the car’s chassis again after
installation.
Para evitar cortocircuitos, recomendamos que desconecte el terminal
negativo de la batería y que efectúe todas las conexiones eléctricas
antes de instalar la unidad.
• Asegúrese de volver a conectar a masa esta unidad al chasis
del automóvil después de la instalación.
Pour éviter tout court-circuit, nous vous recommandons de débrancher
la borne négative de la batterie et d’effectuer tous les raccordements
électriques avant d’installer l’appareil.
• Assurez-vous de raccorder de nouveau la mise à la masse de
cet appareil au châssis de la voiture après l’installation.
Notes:
• Replace the fuse with one of the specified rating. If the fuse blows
frequently, consult your JVC car audio dealer.
• It is recommended to connect speakers with a maximum power
of more than 50 W (both at the rear and at the front, with an
impedance of 4 Ω to 8 Ω). If the maximum power is less than 50 W,
change “AMP GAIN” setting to prevent the speakers from being
damaged (see page 15 of the INSTRUCTIONS).
• To prevent short circuits, cover the terminals of the UNUSED leads
with insulating tape.
• The heat sink becomes very hot after use. Be careful not to touch it
when removing this unit.
Notas:
• Reemplace el fusible por uno con la corriente especificada. Si el
fusible se quemase frecuentemente consulte con su concesionario
de JVC de equipos de audio para automóviles.
• Se recomienda conectar altavoces que tengan una potencia máxima
de más de 50 W (tanto en las partes delantera como trasera, con
una impedancia de 4 Ω á 8 Ω). Si la potencia máxima es de menos
de 50 W, cambie “AMP GAIN” para evitar daños en los altavoces
(consulte la página 15 del MANUAL DE INSTRUCCIONES).
• Para evitar cortocircuitos, cubra los terminales de los conductores
NO UTILIZADOS con cinta aislante.
• El sumidero térmico estará muy caliente después del uso. Asegúrese
de no tocarlo al desmontar esta unidad.
Remarques:
• Remplacer le fusible par un de la valeur précisée. Si le fusible saute
souvent, consulter votre revendeur d’autoradios JVC.
• Il est recommandé de connecter des enceintes avec une puissance
maximum de plus de 50 W (à l’arrière et à l’avant et avec une
impédance de 4 Ω à 8 Ω). Si la puissance maximum est inférieure à
50 W, changez “AMP GAIN” pour éviter d’endommager vos enceintes
(voir page 15 du MANUEL D’INSTRUCTIONS).
• Pour éviter les courts-circuits, recouvrez les extrémités des fils
INUTILISÉS avec une bande isolante.
• Le dissipateur de chaleur devient très chaud après usage. Faire
attention de ne pas le toucher en retirant cet appareil.
Heat sink / Sumidero térmico / Dissipateur de chaleur
PRECAUTIONS on power supply and speaker
connections:
PRECAUCIONES sobre las conexiones de la
fuente de alimentación y de los altavoces:
PRECAUTIONS sur l’alimentation et la
connexion des enceintes:
• DO NOT connect the speaker leads of the power cord to the
car battery; otherwise, the unit will be seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the
speakers, check the speaker wiring in your car.
• NO conecte los conductores de altavoz del cable de
alimentación a la batería de automóvil, pues podrían
producirse graves daños en la unidad.
• ANTES de conectar a los altavoces los conductores de altavoz del
cable de alimentación, verifique el conexionado de altavoz de su
automóvil.
• NE CONNECTEZ PAS les fils d’enceintes du cordon
d’alimentation à la batterie; sinon, l’appareil serait
sérieusement endommagé.
• AVANT de connecter les fils d’enceintes du cordon d’alimentation
aux enceintes, vérifiez le câblage des enceintes de votre voiture.
Parts list for installation and connection
Lista de piezas para instalación y conexión
The following parts are provided for this unit. If any item is missing,
consult your JVC car audio dealer immediately.
Con esta unidad se suministran las siguientes piezas. Si hay algún
elemento faltante, consulte inmediatamente con su concesionario de
JVC de equipos de audio para automóviles.
Liste des pièces pour l’installation et
raccordement
A/B
Hard case/Control panel
Estuche duro/Panel de control
Etui de transport/Panneau de commande
C
Sleeve
Cubierta
Manchon
F
Direct connection cable for iPod
Cable de conexión directa para iPod
Câble de connexion directe pour iPod
G
Washer (ø5)
Arandela (ø5)
Rondelle (ø5)
J
Rubber cushion
Cojín de goma
Amortisseur en caoutchouc
K
Handles
Manijas
Poignées
Les pièces suivantes sont fournies avec cet appareil. Si quelque chose
manquait, consultez votre revendeur autoradio JVC immédiatement.
E
Power cord
Cordón de alimentación
Cordon d’alimentation
D
Trim plate
Placa de guarnición
Plaque d’assemblage
H
Lock nut (M5)
Tuerca de seguridad (M5)
Ecrou d’arrêt (M5)
L
Remote controller
Control remoto
Télécommande
I
Mounting bolt—M4 × 5 mm (M4 × 1/4");
M5 × 12.5 mm (M5 × 1/2")
Perno de montaje—M4 × 5 mm (M4 × 1/4 pulgada);
M5 × 12,5 mm (M5 × 1/2 pulgada)
Boulon de montage—M4 × 5 mm (M4 × 1/4 pouces);
M5 × 12,5 mm (M5 × 1/2 pouces)
M
Battery
Pila
Pile
1
Install1-2_KD-APD49[J]f.indd 1
11/20/07 10:52:02 AM
INSTALLATION
(IN-DASH MOUNTING)
INSTALACION (MONTAJE EN EL
TABLERO DE INSTRUMENTOS)
INSTALLATION (MONTAGE
DANS LE TABLEAU DE BORD)
The following illustration shows a typical installation. If you have any
questions or require information regarding installation kits, consult
your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed
by a qualified technician.
La siguiente ilustración muestra una instalación típica. Si tiene alguna
pregunta o necesita información acerca de las herramientas para
instalación, consulte con su concesionario de JVC de equipos de audio
para automóviles o a una compañía que suministra tales herramientas.
• Si usted no está seguro de cómo instalar correctamente la unidad,
hágala instalar por un técnico cualificado.
L’illustration suivante est un exemple d’installation typique. Si
vous avez des questions ou avez besoin d’information sur des kits
d’installation, consulter votre revendeur d’autoradios JVC ou une
compagnie d’approvisionnement.
• Si l’on n’est pas sûr de pouvoir installer correctement cet appareil, le
faire installer par un technicien qualifié.
Do the required electrical connections.
Realice las conexiones eléctricas requeridas.
Réalisez les connexions électriques.
Bend the appropriate tabs to hold the
sleeve firmly in place.
Doble las lengüetas apropiadas para
retener firmemente la manga en su lugar.
Tordez les languettes appropriées pour
maintenir le manchon en place.
Removing the unit
Extracción de la unidad
Retrait de l’appareil
Before removing the unit, release the rear section.
Antes de extraer la unidad, libere la sección trasera.
Avant de retirer l’appareil, libérer la section arrière.
Insert the two handles, then pull them as
illustrated so that the unit can be removed.
Inserte las dos manijas y, a continuación,
extráigalas de la manera indicada en la ilustración
para poder desmontar la unidad.
Insérez les deux poignées, puis tirez de la façon
illustrée de façon à retirer l’appareil.
When using the optional stay / Cuando emplea un
soporte opcional / Lors de l’utilisation du hauban en
option
Stay (option)
Soporte (opción)
Hauban (en option)
Fire wall
Tabique a prueba de incendios
Cloison
When installing the unit without using the sleeve / Instalación de la unidad sin utilizar
la cubierta / Lors de l’installation de l’appareil scans utiliser de manchon
In a Toyota car for example, first remove the car radio and install the unit in its place.
En un automóvil Toyota, por ejemplo, en primer lugar desmonte el autorradio e instale la unidad en su lugar.
Dans une voiture Toyota, par exemple, retirez d’abord l’autoradio et installez l’appareil à sa place.
Flat head screws—M5 × 8 mm (M5 × 3/8")*2
Tornillos de cabeza plana—M5 × 8 mm (M5 × 3/8 pulgada)*2
Vis à tête plate—M5 × 8 mm (M5 × 3/8 pouces)*2
Dashboard
Tablero de instrumentos
Tableau de bord
Bracket*2
Ménsula*2
Support*2
Screw (option)
Tornillo (opción)
Vis (en option)
Flat head screws—M5 × 8 mm (M5 × 3/8")*2
Tornillos de cabeza plana—M5 × 8 mm (M5 × 3/8 pulgada)*2
Vis à tête plate—M5 × 8 mm (M5 × 3/8 pouces)*2
Pocket
Compartimiento
Poche
Bracket*2
Ménsula*2
Support*2
Note
Install the unit at an angle of less than 30˚.
Instale la unidad a un ángulo de menos de 30˚.
Installez l’appareil avec un angle de moins de 30˚.
*1 When you stand the unit, be careful not to damage the fuse on the
rear.
*2 Not supplied for this unit.
: When installing the unit on the mounting bracket, make sure to use the 8 mm (3/8") -long screws. If longer
screws are used, they could damage the unit.
Nota
: Cuando instala la unidad en la ménsula de montaje, asegúrese de utilizar los tornillos de 8 mm (3/8 pulgada) de
longitud. Si se utilizan tornillos más largos, éstos pueden dañar la unidad.
Remarque : Lors de l’installation de l’appareil sur le support de montage, s’assurer d’utiliser des vis d’une longueur de 8 mm
(3/8 pouces). Si des vis plus longues sont utilisées, elles peuvent endommager l’appareil.
*1 Al poner la unidad vertical, tenga cuidado de no dañar el fusible
provisto en la parte posterior.
*2 No suministrado con esta unidad.
*1 Lorsque vous mettez l’appareil à la verticale, faire attention de ne pas
endommager le fusible situé sur l’arrière.
*2 Non fourni avec cet appareil.
2
Install1-2_KD-APD49[J]f.indd 2
11/20/07 10:52:09 AM
ENGLISH
ESPAÑOL
ELECTRICAL CONNECTIONS
A
FRANÇAIS
CONEXIONES ELECTRICAS
RACCORDEMENTS ELECTRIQUES
Typical connections / Conexiones tipicas / Raccordements typiques
Before connecting: Check the wiring in the vehicle carefully.
Incorrect connection may cause serious damage to this unit.
The leads of the power cord and those of the connector from the car
body may be different in color.
Antes de la conexión: Verifique atentamente el conexionado del
vehículo. Una conexión incorrecta podría producir daños graves en la
unidad.
Los cordones del cable de alimentación y los del conector procedentes
de la carrocería del automóvil podrían ser de diferentes en color.
Avant de commencer la connexion: Vérifiez attentivement le
câblage du véhicule. Une connexion incorrecte peut endommager
sérieusement l’appareil.
Le fil du cordon d’alimentation et ceux des connecteurs du châssis de
la voiture peuvent être différents en couleur.
1
Connect the colored leads of the power cord in the order
specified in the illustration below.
1
Conecte los conductores de color del cable de alimentación en el
orden especificado en la ilustración de abajo.
1
Connectez les fils colorés du cordon d’alimentation dans l’ordre
spécifié sur l’illustration ci-dessous.
2
3
Connect the antenna cord.
2
3
Conecte el cable de antena.
2
3
Connectez le cordon d’antenne.
Finally connect the wiring harness to the unit.
Line out (see diagram )
Salida de línea (véase diagrama )
Sortie de ligne (voir le diagramme )
Por último, conecte el cable de alimentación a la unidad.
Rear ground terminal
Terminal de tierra posterior
Borne arrière de masse
15 A fuse
Fusible de 15 A
Fusible 15 A
Antenna terminal
Terminal de la antena
Borne de l’antenne
iPod connector (see diagram )
Conector iPod (véase diagrama )
Connecteur iPod (voir le diagramme
OE
Steering wheel remote input (see
diagram )—only for KD-APD49
Entrada del control remoto del
volante de dirección (véase
diagrama )—sólo para KD-APD49
Entrée de la télécommande de volant
(voir le diagramme )—seulement
pour le KD-APD49
Black
Negro
Noir
To the metallic body or chassis of the car
A un cuerpo metálico o chasis del automóvil
Vers corps métallique ou châssis de la voiture
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
A un terminal activo del bloque de fusibles conectado a la batería del
automóvil (desviando el interruptor de encendido) (12 V constantes)
A une borne sous tension du porte-fusible connectée à la batterie de la
voiture (en dérivant l’interrupteur d’allumage) (12 V constant)
Red
Rojo
Rouge
Gray with black stripe
Gris con rayas negras
Gris avec bande noire
Left speaker (front)
Altavoz izquierdo (frontal)
Enceinte gauche (avant)
Fuse block
Bloque de fusibles
Porte-fusible
To an accessory terminal in the fuse block
A un terminal accesorio del bloque de fusibles
Vers borne accessoire du porte-fusible
Blue with white stripe
Azul con rayas blancas
Bleu avec bande blanche
White
Blanco
Blanc
)
Ignition switch
Interruptor de encendido
Interrupteur d’allumage
Yellow *2
Amarillo *2
Jaune *2
White with black stripe
Blanco con rayas negras
Blanc avec bande noire
Finalement, connectez le faisceau de fils à l’appareil.
Gray
Gris
Gris
To the remote lead of other equipment or automatic antenna if any (200 mA max.)
Al conductor remoto de otro equipo o de la antena automática, si hubiere (máx. 200 mA)
Au fil de télécommande de l’autre appareil ou à l’antenne automatique s’il y en a une
(200 mA max.)
Green with black stripe
Verde con rayas negras
Vert avec bande noire
Green
Verde
Vert
Right speaker (front)
Altavoz derecho (frontal)
Enceinte droit (avant)
Purple with black stripe
Púrpura con rayas negras
Violet avec bande noire
Left speaker (rear)
Altavoz izquierdo (trasero)
Enceinte gauche (arrière)
Purple
Púrpura
Violet
Right speaker (rear)
Altavoz derecho (trasero)
Enceinte droit (arrière)
B Connecting to the steering wheel remote controller (only for KD-APD49) / Conexión al control remoto del volante de dirección (sólo para
KD-APD49) / Connexion de la télécommande de volant (seulement pour le KD-APD49)
If your car is equipped with the steering wheel remote controller,
you can operate this unit using the controller. For connection, an
exclusive remote adapter (not supplied) which matches your car is
required. For details, consult the same car audio dealer as where the
unit is purchased.
Si su automóvil está equipado con control remoto en el volante de
dirección, podrá controlar este receptor utilizando el control remoto.
Para la conexión, se requiere un adaptador remoto exclusivo (no
suministrado) que sea adecuado para su automóvil. Para los detalles,
consulte con el concesionario car audio donde compró el receptor.
Si votre voiture est équipée d’une télécommande de volant, vous
pouvez commander cet autoradio en utilisant cette télécommande.
Pour la connexion, vous avez besoin d’un adaptateur de
télécommande spécialisé (non fourni) correspondant à votre voiture.
Pour en savoir plus, consultez le revendeur autoradio où vous avez
acheté votre autoradio.
Remote adapter *1
Adaptador para remoto exclusivo *1
Adaptateur pour télécommande spécialisé *1
Steering wheel remote controller (equipped in the car)
Control remoto del volante de dirección (equipado en el vehículo)
Télécommande de volant (installée dans la voiture)
OE
Steering wheel remote input
Entrada del control remoto del volante de dirección
Entrée de la télécommande de volant
*1 Not supplied for this unit.
*2 Before checking the operation of this unit prior to installation, this
lead must be connected, otherwise the power cannot be turned on.
*1 No suministrado con esta unidad.
*2 Antes de comprobar el funcionamiento de esta unidad previa a de
la instalación, es necesario conectar este cable, de lo contrario no se
podrá conectar la alimentación.
*1 Non fourni avec cet appareil.
*2 Pour vérifier le fonctionnement de cet appareil avant installation, ce fil
doit être raccordé, sinon l’appareil ne peut pas être mis sous tension.
3
Install3-4_KD-APD49[J]f.indd 3
11/13/07 11:07:41 AM
C
Connecting the external amplifier or subwoofer / Conexión del amplificador o subwoofer exterior / Conexión del amplificador o subwoofer
exterior
You can connect an amplifier to upgrade your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote
lead of the other equipment so that it can be controlled through
this unit.
• For amplifier only:
– Disconnect the speakers from this unit, connect them to
the amplifier. Leave the speaker leads of this unit unused.
– For KD-APD49: The line output level of this unit is kept high to
maintain the hi-fi sounds reproduced from this unit.
When connecting an external amplifier to this unit, turn down
the gain control on the external amplifier to obtain the best
performance from this unit.
Usted podrá conectar un amplificador para mejorar el sistema estéreo
de su automóvil.
• Conecte el conductor remoto (azul con rayas blancas) al conductor
remoto del otro equipo para poderlo controlar a través de esta unidad.
• Sólo para el amplificador:
– Desconecte los altavoces de esta unidad y conéctelos al
amplificador. Los cables de los altavoces de esta unidad
quedan sin usar.
– Para KD-APD49: El nivel de salida de línea de esta unidad
permanece alto para que corresponda con los sonidos de alta
fidelidad reproducidos por esta unidad.
Cuando conecte un amplificador externo a esta unidad, disminuya
el control de ganancia del amplificador externo para obtener un
óptimo rendimiento de esta unidad.
Vous pouvez connecter un amplificateur pour améliorer votre système
autoradio.
• Connectez le fil de commande à distance (bleu avec bande blanche)
au fil de commande à distance de l’autre appareil de façon qu’il
puisse être commandé via cet appareil.
• Pour l’amplificateur seulement:
– Déconnectez les enceintes de cet appareil et connectezles à l’amplificateur. Laissez les fils d’enceintes de cet
appareil inutilisés.
– Pour le KD-APD49: Le niveau de sortie de ligne de cet appareil
est maintenu à un niveau élevé pour maintenir une qualité Hi-Fi
pour les sons reproduits par cet appareil.
Lors de la connexion d’un amplificateur extérieur à cet appareil,
diminuez le réglage du gain sur l’amplificateur extérieur pour
obtenir les meilleures performances de cet appareil.
Y-connector (not supplied for this unit)
Conector en Y (no suministrado con esta unidad)
Connecteur Y (non fourni avec cet appareil)
Set “L/O MODE” to “REAR”
(See page 15 of the INSTRUCTIONS.)
Ajuste “L/O MODE” a “REAR”
(Consulte la página 15 del MANUAL DE INSTRUCCIONES.)
Réglez “L/O MODE” sur “REAR”
(Voir page 15 du MANUEL D’INSTRUCTIONS.)
Rear speakers
Altavoces posteriores
Enceintes arrière
D
To the remote lead of other
equipment or automatic antenna
if any
Al conductor remoto de
otro equipo o de la antena
automática, si hubiere
Au fil de télécommande de
l’autre appareil ou à l’antenne
automatique s’il y en a une
JVC Amplifier
Amplificador de JVC
JVC Amplificateur
Set “L/O MODE” to “SUB.W”
(See page 15 of the INSTRUCTIONS.)
Ajuste “L/O MODE” a “SUB.W”
(Consulte la página 15 del MANUAL DE INSTRUCCIONES.)
Réglez “L/O MODE” sur “SUB.W”
(Voir page 15 du MANUEL D’INSTRUCTIONS.)
Subwoofer
Subwoofer
Caisson de grave
Remote lead (blue with white stripe)
Cable remoto (azul con rayas blancas)
Fil d’alimentation à distance (bleu avec bande blanche)
JVC Amplifier
Amplificador de JVC
JVC Amplificateur
Signal cord (not supplied for this unit)
Cable de señal (no suministrado con esta
unidad)
Cordon de signal (non fourni avec cet
appareil)
Front speakers
Altavoces delanteros
Enceintes avant
or / o / ou
Connecting an Apple iPod / Conexión del Apple iPod / Connexion d’un iPod Apple
You can connect an iPod to this unit using the supplied direct
connection cable for iPod.
Puede conectar un iPod a esta unidad por medio del cable de
conexión directa para iPod suministrado.
Vous pouvez connecter un iPod à cet appareil en utilisant le câble de
connexion directe du iPod fourni.
Apple iPod (separately purchased)
Apple iPod (adquirido separadamente)
iPod Apple (vendu séparément)
Direct connection cable for iPod (supplied)
Cable de conexión directa para iPod (suministrado)
Câble de connexion directe pour iPod (fourni)
iPod is a trademark of Apple Inc., registered in the U.S. and other
countries.
*3 Remote lead
*4 Firmly attach the ground wire to the metallic body or to the chassis of
the car—to the place uncoated with paint (if coated with paint, remove
the paint before attaching the wire). Failure to do so may cause damage
to the unit.
TROUBLESHOOTING
iPod es una marca comercial de Apple Inc., registrada en los EE.UU. y
otros países.
iPod est une marque de commerce d’Apple Inc., enregistrée aux
États-Unis et dans les autres pays.
*3 Cable remoto
*4 Fije firmemente el cable de tierra a la carrocería metálica o al chasis—a
*3 Fil d’alimentation à distance
*4 Attachez solidement le fil de mise à la masse au châssis métallique de
un lugar no cubierto con pintura (si está cubierto con pintura, quítela
antes de fijar el cable). De lo contrario, se podrían producir daños en la
unidad.
LOCALIZACION DE AVERIAS
la voiture—à un endroit qui n’est pas recouvert de peinture (s’il est
recouvert de peinture, enlevez d’abord la peinture avant d’attacher le fil).
L’appareil peut être endommagé si cela n’est pas fait correctement.
EN CAS DE DIFFICULTES
• The fuse blows.
* Are the red and black leads connected correctly?
• El fusible se quema.
* ¿Están los conductores rojo y negro correctamente conectados?
• Le fusible saute.
* Les fils rouge et noir sont-ils racordés correctement?
• Power cannot be turned on.
* Is the yellow lead connected?
• No es posible conectar la alimentación.
* ¿Está el cable amarillo conectado?
• L’appareil ne peut pas être mise sous tension.
* Le fil jaune est-elle raccordée?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• No sale sonido de los altavoces.
* ¿Está el cable de salida del altavoz cortocircuitado?
• Pas de son des enceintes.
* Le fil de sortie d’enceinte est-il court-circuité?
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• El sonido presenta distorsión.
* ¿Está el cable de salida del altavoz conectado a masa?
* ¿Están los terminales “–” de los altavoces L y R conectados a una
masa común?
• Le son est déformé.
* Le fil de sortie d’enceinte est-il à la masse?
* Les bornes “–” des enceintes gauche et droit sont-elles mises ensemble
à la masse?
• Perturbación de ruido.
* ¿El terminal de tierra trasero está conectado al chasis del automóvil
utilizando los cordones más corto y más grueso?
• Interférence avec les sons.
* La prise arrière de mise à la terre est-elle connectée au châssis de la
voiture avec un cordon court et épais?
• Esta unidad se calienta.
* ¿Está el cable de salida del altavoz conectado a masa?
* ¿Están los terminales “–” de los altavoces L y R conectados a una
masa común?
• Cet appareil devient chaud.
* Le fil de sortie d’enceinte est-il à la masse?
* Les bornes “–” des enceintes gauche et droit sont-elles mises ensemble
à la masse?
• Esta unidad no funciona en absoluto.
* ¿Reinicializó la unidad?
4
• Cet appareil ne fonctionne pas du tout.
* Avez-vous réinitialisé votre appareil?
• Noise interfere with sounds.
* Is the rear ground terminal connected to the car’s chassis using
shorter and thicker cords?
• This unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• This unit does not work at all.
* Have you reset your unit?
Install3-4_KD-APD49[J]f.indd 4
11/1/07 3:32:15 PM
KD-PDR45
ENGLISH
CD RECEIVER
KD-PDR45
For canceling the display demonstration, see page 6.
For installation and connections, refer to the separate manual.
INSTRUCTIONS
GET0489-001A
[U/UH]
Cover_KD-PDR45[U]_5.indd 1
11/2/07 8:57:19 AM
ENGLISH
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best
possible performance from the unit.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to
qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical
instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
Detaching the control panel
[European Union only]
Warning:
If you need to operate the unit while driving, be
sure to look around carefully or you may be involved
in a traffic accident.
Attaching the control panel
2
EN02-05_KD-PDR45[U]_5.indd 2
11/2/07 8:56:33 AM
CONTENTS
Control panel .................................. 4
Remote controller — RM-RK50........... 5
Getting started ................................ 6
ENGLISH
How to reset your unit
Basic operations ................................................... 6
• Your preset adjustments will also be erased.
Radio operations ............................. 7
Disc operations ................................ 8
Playing a disc in the unit ..................................... 8
How to forcibly eject a disc
• Be careful not to drop the disc when it ejects.
• If this does not work, reset your unit.
How to use the M MODE button
If you press M MODE, the unit goes into functions mode,
then the number buttons and 5/∞ buttons work as
different function buttons.
Ex.: When number button 2 works as
MO (monaural) button.
iPod operations ...............................
Sound adjustments ..........................
General settings — PSM ..................
Other external component
operations ...................................
Title assignment..............................
Maintenance ...................................
More about this unit ........................
Troubleshooting ..............................
Specifications ..................................
10
12
14
16
16
17
17
20
22
For safety...
• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
• Stop the car before performing any complicated
operations.
Temperature inside the car...
To use these buttons for their original functions
again after pressing M MODE, press M MODE again.
• Waiting for about 5 seconds without pressing any of
these buttons will automatically cancels the functions
mode.
If you have parked the car for a long time in hot or cold
weather, wait until the temperature in the car becomes
normal before operating the unit.
3
EN02-05_KD-PDR45[U]_5.indd 3
11/2/07 8:56:34 AM
ENGLISH
Control panel
Parts identification
Display window
1
2
3
4
5
6
7
8
9
p
q
w
e
r
t
y
u
i
5 (up) / ∞ (down) buttons
0 (eject) button
(standby/on attenuator) button
Control dial
Remote sensor
DO NOT expose the remote sensor to strong light
(direct sunlight or artificial lighting).
BAND button
Loading slot
Display window
EQ (equalizer) button
DISP (display) button
(control panel release) button
i (iPod) button
4 /¢ buttons
SRC (source) button
SEL (select) button
M MODE button
MO (monaural) button
SSM (Strong-station Sequential Memory) button
o
;
a
s
d
f
g
h
j
k
l
/
z
x
Number buttons
RPT (repeat) button
RND (random) button
AUX (auxiliary) input jack
Source display / Track number / Folder number /
Time countdown indicator
Tr (track) indicator
DISC indicator
Playback mode / item indicators— RND (random),
(disc), (folder), RPT (repeat)
Tuner reception indicators—ST (stereo),
MO (monaural)
Sound mode (iEQ: intelligent equalizer) indicators
—CLASSIC, HIP HOP, JAZZ, ROCK, POPS, USER
LOUD (loudness) indicator
EQ (equalizer) indicator
Disc information indicators—
TAG (Tag information), (folder), (track/file)
Main display
4
EN02-05_KD-PDR45[U]_5.indd 4
11/2/07 8:56:35 AM
Remote controller — RM-RK50
ENGLISH
Main elements and features
Installing the lithium coin battery
(CR2025)
1
2
Aim the remote controller directly at the remote
sensor on the unit. Make sure there is no obstacle
in between.
Warning:
• Do not install any battery other than CR2025 or its
equivalent; otherwise, it may explode.
• Do not leave the remote controller in a place
(such as the dashboard) exposed to direct
sunlight for a long time; otherwise, it may
explode.
• Store the battery in a place where children cannot
reach to avoid the risk of accidents.
• To prevent the battery from over-heating,
cracking, or starting a fire:
– Do not recharge, short, disassemble, heat the
battery, or dispose of it in a fire.
– Do not leave the battery with other metallic
materials.
– Do not poke the battery with tweezers or
similar tools.
– Wrap the battery with tape and insulate when
throwing away or saving it.
3
4
5
6
(standby/on/attenuator) button
• Turns the power on if pressed briefly or
attenuates the sound when the power is on.
• Turns the power off if pressed and held.
5 U (up) / D (down) ∞ buttons
• Changes the FM/AM bands with 5 U.
• Changes the preset stations with D ∞.
• Changes the folder of the MP3/WMA discs.
• While listening to an Apple iPod.
– Enters the main menu if pressed and held.
(Now 5 U/D ∞/2 R/F 3 work as the menu
selecting buttons.)
• While listening to an iPod (in menu selecting
mode):
– Selects an item if pressed D ∞ briefly. (Then,
press and hold D ∞ to play back the selection
directly.)
– Returns to the previous menu if pressed 5 U
briefly.
VOL – / VOL + buttons
• Adjusts the volume level.
SOUND button
• Selects the sound mode (iEQ: intelligent
equalizer).
SOURCE button
• Selects the source.
2 R (reverse) / F (forward) 3 buttons
• Searches for stations if pressed briefly.
• Fast-forwards or reverses the track if pressed and
held.
• Changes the track if pressed briefly.
• While listening to an iPod (in menu selecting
mode):
– Accelerated file search: Hold 2 R/F 3 to fast
skip during song search in the main menu.
5
EN02-05_KD-PDR45[U]_7.indd 5
11/20/07 12:16:46 PM
ENGLISH
Getting started
Basic operations
~
Turn on the power.
To drop the volume in a
moment (ATT)
To restore the sound, press
the button again.
To turn off the power
Ÿ
Basic settings
• See also “General settings — PSM” on pages
14 and 15.
1
*1 You cannot select “CD” as the playback source
if there is no disc in the unit.
*2 “NO IPOD” appears if an iPod is not connected.
!
2
For FM/AM tuner
1 Canceling the display demonstrations
Select “DEMO,” then “DEMO OFF.”
2 Setting the clock
⁄
Select “CLOCK HOUR,” then adjust the hour.
Select “CLOCK MIN” (minute), then adjust the
minute.
Adjust the volume.
3
Volume level appears.
@
Adjust the sound as you want. (See
pages 12 and 13.)
Finish the procedure.
To check the current clock time while the
power is turned off
Clock time is shown on the display for
about 5 seconds. See also page 14.
Caution on volume setting:
Discs produce very little noise compared with other
sources. Lower the volume before playing a disc
to avoid damaging the speakers by the sudden
increase of the output level.
6
EN06-13_KD-PDR45[U]_5.indd 6
11/2/07 8:56:47 AM
When an FM stereo broadcast is hard to
receive
~
Lights up when monaural mode is activated.
Ÿ
Reception improves, but the stereo effect will be lost.
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
!
ENGLISH
Radio operations
To restore the stereo effect, repeat the same
procedure. “MONO OFF” appears and the MO indicator
goes off.
Storing stations in memory
Start searching for a station.
You can preset six stations for each band.
When a station is received, searching stops.
To stop searching, press the same button
again.
FM station automatic presetting—
SSM (Strong-station Sequential
Memory)
1
Select the FM band (FM1 – FM3) you want to
store into.
To tune in to a station manually
In step ! above...
1
2
3
2 Select a desired station frequency.
“SSM” flashes, then disappears when automatic
presetting is over.
Local FM stations with the strongest signals are
searched and stored automatically in the FM band.
7
EN06-13_KD-PDR45[U]_5.indd 7
11/2/07 8:56:48 AM
ENGLISH
Manual presetting
Ex.: Storing the FM station of 92.50 MHz into preset
number 4 of the FM1 band.
1
Disc operations
Playing a disc in the unit
All tracks will be played repeatedly until you change the
source or eject the disc.
2
3
To stop play and eject the disc
Preset number flashes for a while.
Listening to a preset station
1
2
• Press SRC to listen to another
playback source.
[Hold] To fast-forward or reverse the
track
Select the preset station (1 – 6) you want.
[Press] To go to the next or previous
track
or
[Press] To go to the next or previous
folder (only for MP3 or WMA
discs)
To locate a particular track (for CD) or folder
(for MP3 or WMA discs) directly
To check other information while listening
to the radio
Frequency = Clock =
Station name * = (back to the
beginning)
To select a number from 01 – 06:
To select a number from 07 – 12:
* If no title is assigned to a station, “NO NAME” appears.
To assign a title to a station, see page 16.
8
EN06-13_KD-PDR45[U]_5.indd 8
11/2/07 8:56:49 AM
To select a particular track in a folder
(for MP3 or WMA discs):
Changing the display information
While playing an audio CD or CD Text
ENGLISH
• To use direct folder access on MP3/WMA discs, it
is required that folders are assigned with 2-digit
numbers at the beginning of their folder names—
01, 02, 03, and so on.
A = B = Disc title/performer *1 = Track
title *1 [ ] = (back to the beginning)
Other main functions
Skipping tracks quickly during play
• For MP3 or WMA discs, you can skip tracks within the
same folder.
Ex.: To select track 32 while playing a track whose
number is a single digit (1 to 9)
While playing an MP3 or a WMA track
• When “TAG DISPLAY” is set to “TAG ON”
(see page 15)
A = B = Album name/performer (folder
name *2) [
] = Track title (file
name *2) [
] = (back to the beginning)
• When “TAG DISPLAY” is set to “TAG OFF”
1
A = B = Folder name [ ] = File name
[ ] = (back to the beginning)
2
Each time you press the button, you can skip 10
tracks.
• After the last track, the first track will be selected
and vice versa.
3
A : Current track number with the elapsed playing
time
B : Current track number with the clock time
[ ] : Corresponding indicator lights up on the display.
*1 If the current disc is an audio CD, “NO NAME” appears.
*2 If an MP3/WMA file does not have Tag information,
folder name and file name appear. In this case, the
TAG indicator will not light up.
Prohibiting disc ejection
You can lock a disc in the loading slot.
“EJECT LOCK” flashes on the display.
To cancel the prohibition, repeat the same
procedure.
9
EN06-13_KD-PDR45[U]_5.indd 9
11/2/07 8:56:49 AM
ENGLISH
Selecting the playback modes
You can use only one of the following playback modes
at a time.
1
2
Select your desired playback mode.
iPod operations
You can play songs in an Apple iPod by connecting it
with the supplied direct connection cable for iPod.
You can control playback from the unit or from your
iPod.
• Disconnecting the iPod will stop playback. Press SRC
to listen to another playback source.
Caution:
7 Repeat play
Mode
Plays repeatedly
]
TRACK RPT : The current track. [
FOLDER RPT * : All tracks of the current folder.
[
]
RPT OFF
: Cancels.
7 Random play
Mode
Plays at random
• Avoid using the iPod if it might hinder your safety
while driving.
• Make sure all important data has been backed up
to avoid losing the data.
• For connection, see the Installation/Connection
Manual (separate volume).
• For details, refer also to the manual supplied for your
iPod.
~
Connect an iPod.
Direct connection
cable for iPod
FOLDER RND *: All tracks of the current folder,
then the tracks of the next folder
and so on. [
]
ALL RND
: All tracks of the current disc.
[
]
RND OFF
: Cancels.
* Only while playing an MP3 or a WMA disc.
If an iPod has been connected...
To directly select “IPOD” as the source
while listening to another source or
when the power is turned off.
[ ] : Corresponding indicator lights up on the
display.
Playback starts automatically from where it had
been paused previously.
Ÿ
Adjust the volume.
10
EN06-13_KD-PDR45[U]_5.indd 10
11/2/07 8:56:50 AM
Adjust the sound as you want. (See
pages 12 and 13.)
Selecting a track from the menu
1
ENGLISH
!
Enter the main menu.
To control playback from your iPod
or
“IPOD MODE” appears on the
display.
Now the 5/∞/4 /¢ /number
buttons work as the menu selecting buttons.
• Press and hold this button again to control playback
from the unit. “HEAD MODE” appears on the display.
2
Select the desired menu.
Playback control from the unit
[Press] Go to the next or previous
track
[Hold] Fast-forward or reverse the
track during playback
Fast-skip the menu items of
the main menu
PLAYLIST Ô ARTIST Ô ALBUM Ô SONG
Ô PODCASTÔ GENRE Ô COMPOSER Ô
AUDIOBOOK Ô (back to the beginning)
[Hold] Enter the main menu (see the
right column).
[Press] Pause/resume playback.
• Pressing the number buttons can directly select
the desired menu (see the left column for
details).
3
Confirm the selection.
To move back to the previous
menu, press 5.
[Press] Go to the top menu of “PLAYLIST,” “ARTIST,”
“ALBUM,” “SONG,” “PODCAST,” or “GENRE” in
the main menu (see the right column).
[Hold] Go to the top menu of “COMPOSER” or
“AUDIOBOOK” in the main menu (see the
right column).
• Holding the button will start play back the
selected item directly.
• If a track is selected, playback starts
automatically.
• If the selected item has another layer, you will
enter the layer. Repeat steps 2 and 3 until the
desired track is played.
• Accelerated file search: Hold 4 /¢
to fast skip during song search in the main
menu.
Continued on the next page
11
EN06-13_KD-PDR45[U]_7.indd 11
11/20/07 12:49:50 PM
ENGLISH
To exit from menu selecting mode
To check other information while listening
to an iPod
or
* The menu selecting mode will be canceled:
– If no operations are performed for about
10 seconds.
– When you confirm the selection of a track.
– Pressing some other buttons such as DISP, SEL,
MODE, or EQ.
Current track number with the elapsed
playing time = Current track number with
the clock time = Track title * = Album name/
performer * = (back to the beginning)
* When “TAG DISPLAY” is set to “TAG OFF,” file name and
folder name appear.
Selecting the playback modes
1
2
Sound adjustments
You can select a preset sound mode suitable to the
music genre (iEQ: intelligent equalizer).
Select your desired playback mode.
7 Repeat play
Mode
ONE RPT
ALL RPT
RPT OFF
Playback functions (as on iPod)
: Same as “Repeat One.” [
: Same as “Repeat All.” [
: Cancels.
Adjusting the sound
]
]
You can adjust the sound characteristics to your
preference.
• The adjustment you make will be stored for the
currently selected sound mode (iEQ) including
“USER.”
7 Random play
Mode
Playback functions (as on iPod)
SONG RND : Same as “Shuffle Songs.” [
ALBUM RND * : Same as “Shuffle Albums.”
[
]
RND OFF
: Cancels.
]
1
2
* Functions only if you select “ALL” in “ALBUMS” of
the main menu
[ ] : Corresponding indicator lights up on the
display.
Indication, [Range]
FADER *2, [R06 to F06]
Adjust the front and rear speaker balance.
BALANCE *3, [L06 to R06]
Adjust the left and right speaker balance.
12
EN06-13_KD-PDR45[U]_7.indd 12
11/20/07 12:23:25 PM
3
Select a sound characteristic.
4
Adjust the sound elements of the selected
sound characteristic.
1 Adjust the frequency.
LOUD *4 (loudness), [LOUD ON or LOUD OFF]
Boost low and high frequencies to produce a
well-balanced sound at a low volume level.
SUBWOOFER *1, [00 to 08, initial: 04]
Adjust the subwoofer output level.
VOL ADJ (volume adjust), [–05 to +05, initial: 00]
Adjust the volume level of each source (except FM), in
relation to the FM volume level. The volume level will
automatically increase or decrease when you change
the source.
• Before making an adjustment, select the source you
want to adjust.
ENGLISH
Indication, [Range]
2 Adjust the level.
VOLUME, [00 to 50 or 00 to 30 ]*5
Adjust the volume.
*1 Displayed only when “L/O MODE” is set to “SUB.W”
(see page 15).
*2 If you are using a two-speaker system, set the fader
level to “00.”
*3 This adjustment will not affect the subwoofer output.
*4 The adjustment made (LOUD ON/LOUD OFF) will be
applied to all sound modes.
*5 Depending on the amplifier gain control setting. (See
page 15 for details.)
3 Adjust the quality slope (Q).
Sound
elements
BASS
MID
TRE
Frequency
60 Hz
80 Hz
100 Hz
120 Hz
500 Hz
1.0 kHz
1.5 kHz
2.5 kHz
7.5 kHz
10.0 kHz
12.5 kHz
15.0 kHz
Level
–06 to
+06
–06 to
+06
–06 to
+06
Q (Q-slope)
Q0.5
Q1.0
Q1.5
Q2.0
Q0.75
Q1.0
Q1.25
Q1.5
Q0.75
Q1.25
Storing your own sound mode
You can adjust the sound modes and store your own
adjustments in memory.
1
2
Range/selectable items
Select a sound mode.
Enter the adjustment mode.
• If no operation is done within
5 seconds, this mode is canceled.
BASS: Bass MID: Mid-range TRE: Treble
5
The adjustment made will be stored
automatically. Repeat steps 3 and 4 to adjust
other sound characteristics.
13
EN06-13_KD-PDR45[U]_7.indd 13
11/20/07 12:23:26 PM
ENGLISH
General settings — PSM
You can change PSM (Preferred Setting Mode) items
listed in the table below and on page 15.
3
Adjust the PSM item selected.
4
Repeat steps 2 and 3 to adjust other PSM
items if necessary.
5
Finish the procedure.
1
2
Select a PSM item.
Indications
Item
( : Initial)
Setting, [reference page]
DEMO
Display
demonstration
• DEMO ON
: The display demonstration will be activated automatically if no
operation is done for about 20 seconds, [6].
: Cancels.
CLOCK DISP *1
Clock display
• CLOCK ON
• DEMO OFF
• CLOCK OFF
: The clock time is shown on the display at all times when the power is
turned off.
: Cancels; pressing DISP will show the clock time for about 5 seconds
when the power is turned off, [6].
CLOCK HOUR
Hour adjustment
1 – 12
[Initial: 1 (1:00)], [6].
CLOCK MIN
Minute adjustment
00 – 59
[Initial: 00 (1:00)], [6].
DIMMER
Dimmer
• ON
• OFF
: Dims the display and button illumination.
: Cancels.
*1 If the power supply is not interrupted by turning off the ignition key of your car, it is recommended that you select
“CLOCK OFF” to save the car’s battery.
14
EN14-23_KD-PDR45[U]_5.indd 14
11/2/07 8:57:02 AM
Item
( : Initial)
Setting, [reference page]
AUDIOBOOKS *2
Speed control of
“Audiobook”
• NORMAL
• FASTER
• SLOWER
: You can select the playback speed of the “Audiobook” sound file in
your iPod.
SCROLL *3
Scroll
• ONCE
• AUTO
• OFF
:
:
:
•
L/O MODE
Line output mode
• REAR
: Select if the REAR LINE OUT terminals are used for connecting the
speakers (through an external amplifier).
: Select if the REAR LINE OUT terminals are used for connecting a
subwoofer (through an external amplifier).
• SUB.W
ENGLISH
Indications
Scrolls the displayed information once.
Repeats scrolling (at 5-second intervals).
Cancels.
Pressing DISP for more than one second can scroll the display
regardless of the setting.
SUB.W FREQ *4
Subwoofer cutoff
frequency
• LOW
• MID
• HIGH
: Frequencies lower than 90 Hz are sent to the subwoofer.
: Frequencies lower than 135 Hz are sent to the subwoofer.
: Frequencies lower than 180 Hz are sent to the subwoofer.
TAG DISPLAY
Tag display
• TAG ON
• TAG OFF
: Shows the Tag information while playing MP3/WMA tracks, [9].
: Cancels.
AMP GAIN
Amplifier gain
control
• LOW POWER
IF BAND
Intermediate
frequency band
• AUTO
: VOLUME 00 – VOLUME 30. (Select this if the maximum power of the
speaker is less than 50 W to avoid damaging the speaker.)
• HIGH POWER : VOLUME 00 – VOLUME 50.
• WIDE
: Increases the tuner selectivity to reduce interference noise between
close stations. (The stereo effect may be lost.)
: Subject to interference noise from adjacent stations, but the sound
quality will not be degraded and the stereo effect will remain.
*2 Displayed only when an iPod is connected and playback is controlled from the unit.
*3 Some characters or symbols will not be shown correctly (or will be blanked) on the display.
*4 Displayed only when “L/O MODE” is set to “SUB.W.”
15
EN14-23_KD-PDR45[U]_5.indd 15
11/2/07 8:57:04 AM
ENGLISH
Other external component
operations
You can connect an external component to the AUX
(auxiliary) input jack on the control panel.
Title assignment
You can assign names to 30 station frequencies (FM and
AM) and up to 8 characters for each station name.
1
Select FM/AM.
2
Show the title entry screen.
3
Assign a title.
1 Select a character.
Portable audio player, etc.
3.5 mm stereo mini
plug (not supplied)
~
Ÿ
!
Turn on the connected component and
start playing the source.
Adjust the volume.
2 Move to the next (or previous) character
position.
⁄
3 Repeat steps 1 and 2 until you finish
Adjust the sound as you want. (See
pages 12 and 13.)
entering the title.
4
Finish the procedure.
To check other information while listening
to an external component
Clock Ô AUX IN
To erase the entire title
In step 2 above...
16
EN14-23_KD-PDR45[U]_5.indd 16
11/2/07 8:57:05 AM
How to clean the connectors
Frequent detachment will deteriorate the connectors.
To minimize this possibility, periodically wipe the
connectors with a cotton swab or cloth moistened with
alcohol, being careful not to damage the connectors.
To play new discs
New discs may have some rough spots
around the inner and outer edges. If
such a disc is used, this unit may reject
the disc.
To remove these rough spots, rub the edges with a
pencil or ball-point pen, etc.
ENGLISH
Maintenance
Do not use the following discs:
Connectors
Single CD (8 cm disc)
Warped disc
Sticker and
sticker residue
Stick-on label
Moisture condensation
Moisture may condense on the lens inside the unit in
the following cases:
• After starting the heater in the car.
• If it becomes very humid inside the car.
Should this occur, the unit may malfunction. In this
case, eject the disc and leave the unit turned on for a
few hours until the moisture has evaporated.
How to handle discs
When removing a disc from its case, press down the
center holder of the case and lift the Center holder
disc out, holding it by the edges.
• Always hold the disc by the edges.
Do not touch its recording surface.
When storing a disc in its case, gently insert the
disc around the center holder (with the printed surface
facing up).
• Make sure to store discs in cases after use
To keep discs clean
A dirty disc may not play correctly.
If a disc does become dirty, wipe it with
a soft cloth in a straight line from center
to edge.
• Do not use any solvents (for example, conventional
record cleaner, spray, thinner, benzine, etc.) to clean
discs..
Unusual shape
More about this unit
Basic operations
Turning on the power
• By pressing SRC (source) or i (iPod) button on the
unit, you can also turn on the power. If the source is
ready, playback also starts.
Turning off the power
• If you turn off the power while listening to a track,
playback will start from where it had been stopped
previously next time you turn on the power.
General
• If you change the source while listening to a disc or
an iPod, playback stops.
Next time you select “CD” or “IPOD” as the playback
source, playback will start from where it had been
stopped/paused previously.
Continued on the next page
17
EN14-23_KD-PDR45[U]_5.indd 17
11/13/07 12:14:43 PM
ENGLISH
• After ejecting a disc or disconnecting an iPod,
“NO DISC” or “NO IPOD” appears and you cannot
operate some of the buttons. Insert another disc,
connect an iPod, or press SRC to select another
playback source.
Tuner operations
Storing stations in memory
• During SSM search...
– All previously stored stations are erased and the
stations are stored anew.
– Received stations are preset in No. 1 (lowest
frequency) to No. 6 (highest frequency).
– When SSM is over, the station stored in No. 1 will
be automatically tuned in.
• When storing a station manually, the previously
preset station is erased when a new station is stored
in the same preset number.
Disc operations
Caution for DualDisc playback
• The Non-DVD side of a “DualDisc” does not comply
with the “Compact Disc Digital Audio” standard.
Therefore, the use of Non-DVD side of a DualDisc on
this product may not be recommended.
General
• This unit has been designed to reproduce
CDs/CD Texts, and CD-Rs (Recordable)/CD-RWs
(Rewritable) in audio CD (CD-DA), MP3 and WMA
formats.
• When a disc is inserted upside down, “PLEASE” and
“EJECT” appear alternately on the display. Press 0 to
eject the disc.
• MP3 and WMA “tracks” (words “file” and “track” are
used interchangeably) are recorded in “folders.”
• While fast-forwarding or reversing on an MP3 or
WMA disc, you can only hear intermittent sounds.
Playing a CD-R or CD-RW
• Use only “finalized” CD-Rs or CD-RWs.
• This unit can only play back files of the same type as
those which are detected first if a disc includes both
audio CD (CD-DA) files and MP3/WMA files.
• This unit can play back multi-session discs; however,
unclosed sessions will be skipped while playing.
• Some CD-Rs or CD-RWs may not play back on this
unit because of their disc characteristics, or for the
following reasons:
– Discs are dirty or scratched.
– Moisture condensation has occurred on the lens
inside the unit.
– The pickup lens inside the unit is dirty.
– The files on the CD-R/CD-RW are written using the
“Packet Write” method.
– There are improper recording conditions (missing
data, etc.) or media conditions (stained, scratched,
warped, etc.).
• CD-RWs may require a longer readout time since the
reflectance of CD-RWs is lower than that of regular
CDs.
• Do not use the following CD-Rs or CD-RWs:
– Discs with stickers, labels, or a protective seal stuck
to the surface.
– Discs on which labels can be directly printed by an
ink jet printer.
Using these discs under high temperature or high
humidity may cause malfunctions or damage to the
unit.
Playing an MP3/WMA disc
• This unit can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of
the letter case—upper/lower).
• This unit can show the names of albums, artists
(performer), and Tag (Version 1.0, 1.1, 2.2, 2.3, or
2.4) for MP3 files and for WMA files.
• This unit can display only one-byte characters. No
other characters can be correctly displayed.
• This unit can play back MP3/WMA files meeting the
conditions below:
– Bit rate: 8 kbps — 320 kbps
18
EN14-23_KD-PDR45[U]_6.indd 18
11/14/07 4:35:31 PM
•
•
•
•
Ejecting a disc
• If the ejected disc is not removed within 15 seconds,
it is automatically inserted into the loading slot again
to protect it from dust. Playback starts automatically.
iPod operations
• Controllable iPod:
– iPod mini
– iPod G4
•
•
•
•
•
•
•
•
•
– iPod photo
– iPod nano (1st & 2nd Generation)
– iPod with video (5th Generation)
Update your iPod to the latest software version
before using it with this unit.
When you turn on this unit, the iPod is charged
through this unit.
While connecting an iPod with Video:
– No video shows on the iPod’s display or the
external monitor (only the audio part is available).
– It is not possible to browse video files on the
“Video“ menu. (If you connect the iPod during
the playback or pausing of a video file, resuming
playback will not work.)
iPod shuffle cannot be used with this unit.
You can control the iPod from this unit when “JVC” or
“ ” appears on the iPod display after connection.
The song order displayed on the selection menu of
this unit may differ from that of the iPod.
If playback is stopped, select a track from the
selection menu or press BAND to playback the same
track again.
The text information may not be displayed correctly:
– Some characters such as accented letters cannot be
shown correctly on the display.
– Communication between the iPod and the unit is
not stable.
If the text information includes more than
11 characters, it scrolls on the display. This unit can
display up to 64 characters.
ENGLISH
•
– Sampling frequency:
48 kHz, 44.1 kHz, 32 kHz (for MPEG-1)
24 kHz, 22.05 kHz, 16 kHz (for MPEG-2)
– Disc format: ISO 9660 Level 1/Level 2, Romeo,
Joliet, Windows long file name
The maximum number of characters for file/folder
names vary depending on the disc format used
(includes 4 extension characters—<.mp3> or
<.wma>).
– ISO 9660 Level 1: up to 12 characters
– ISO 9660 Level 2: up to 31 characters
– Romeo: up to 128 characters
– Joliet: up to 64 characters
– Windows long file name: up to 128 characters
This unit can recognize a total of 512 files,
255 folders, and 8 hierarchical levels.
This unit can play back files recorded in VBR (variable
bit rate).
Files recorded in VBR have a discrepancy in the
elapsed time display, and do not show the actual
elapsed time. In particular, this difference becomes
noticeable after performing the search function.
This unit cannot play back the following files:
– MP3 files encoded in MP3i and MP3 PRO format.
– MP3 files encoded in an inappropriate format.
– MP3 files encoded with Layer 1/2.
– WMA files encoded in lossless, professional, and
voice format.
– WMA files which are not based upon Windows
Media® Audio.
– WMA files copy-protected with DRM.
– Files which have data such as AIFF, ATRAC3, etc.
The search function works but search speed is not
constant.
Notice:
When operating an iPod, some operations may not
be performed correctly or as intended. In this case,
visit the following JVC web site:
<http://www.jvc-victor.co.jp/english/car/>
General settings—PSM
• If you change the “AMP GAIN” setting from
“HIGH POWER” to “LOW POWER” while the
volume level is set higher than “VOLUME 30,” the
unit automatically changes the volume level to
“VOLUME 30.”
Continued on the next page
19
EN14-23_KD-PDR45[U]_7.indd 19
11/20/07 12:23:44 PM
ENGLISH
Preset value setting for each sound mode
Preset value
Sound mode
BASS (bass)
Freq.
Level
MID (mid-range)
Q
Freq.
Level
TRE (treble)
Q
Freq.
Level
LOUD
(loudness)
Q
USER
60 Hz
00
Q1.0 1.0 kHz
00
Q1.25
7.5 kHz
00
Q1.25
ROCK
100 Hz
+03
Q1.0 1.0 kHz
00
Q1.25 10.0 kHz
+02
Q1.25
80 Hz
+01
Q1.0 1.0 kHz
00
Q1.25 10.0 kHz
+03
Q1.25
100 Hz
+02
Q1.0 1.0 kHz
+01
Q1.25 10.0 kHz
+02
Q1.25
HIP HOP
60 Hz
+04
Q1.0 1.0 kHz
–02
Q1.0 10.0 kHz
+01
Q1.25
JAZZ
80 Hz
+03
Q1.0 1.0 kHz
00
Q1.25 10.0 kHz
+03
Q1.25
CLASSIC
POP
OFF
Freq.: Frequency Q: Q-slope
Troubleshooting
What appears to be trouble is not always serious. Check the following points before calling a service center.
FM/AM
General
Symptoms
Remedies/Causes
• Sound cannot be heard from the speakers.
• Adjust the volume to the optimum level.
• Check the cords and connections.
• The unit does not work at all.
Reset the unit (see page 3).
• SSM automatic presetting does not work.
Store stations manually.
• Static noise while listening to the radio.
Connect the antenna firmly.
• Disc cannot be played back.
Insert the disc correctly.
Disc playback
• CD-R/CD-RW cannot be played back.
• Insert a finalized CD-R/CD-RW.
• Tracks on the CD-R/CD-RW cannot be skipped. • Finalize the CD-R/CD-RW with the component which
you used for recording.
• Disc can neither be played back nor ejected.
• Unlock the disc (see page 9).
• Eject the disc forcibly (see page 3).
• Disc sound is sometimes interrupted.
• Stop playback while driving on rough roads.
• Change the disc.
• Check the cords and connections.
• “NO DISC” appears on the display.
• “PLEASE” and “EJECT“ appear alternately on
the display.
Insert a playable disc into the loading slot.
20
EN14-23_KD-PDR45[U]_5.indd 20
11/13/07 12:14:47 PM
MP3/WMA playback
Remedies/Causes
• Disc cannot be played back.
• Use a disc with MP3/WMA tracks recorded in a format
compliant with ISO 9660 Level 1, Level 2, Romeo, or
Joliet.
• Add the extension code <.mp3> or <.wma> to the
file names.
• Noise is generated.
Skip to another track or change the disc. (Do not add the
extension code <.mp3> or <.wma> to non-MP3 or
WMA tracks.)
ENGLISH
Symptoms
• A longer readout time is required (“READING” Do not use too many hierarchical levels and folders.
keeps flashing on the display).
• Tracks do not play back in the order you have The playback order is determined when the files are
intended them to play.
recorded.
• The elapsed playing time is not correct.
This sometimes occurs during playback. This is caused by
how the tracks are recorded on the disc.
iPod playback
• The correct characters are not displayed (e.g. This unit can only display letters (upper case), numbers,
album name).
and a limited number of symbols.
• The iPod does not turn on or does not work.
• Check the connecting cable and its connection.
• Update the firmware version.
• Charge the battery.
• The sound is distorted.
Deactivate the equalizer either on the unit or the iPod.
• “NO IPOD” appears on the display.
• Check the connecting cable and its connection.
• Charge the battery.
• Playback stops.
The headphones are disconnected during playback. Turn
off the unit’s power and turn it on again.
• No sound can be heard when connecting an
iPod nano.
• Disconnect the headphones from the iPod nano.
• Update the firmware version of the iPod nano.
• “NO FILES” appears on the display.
No tracks are stored. Import tracks to the iPod.
• The iPod’s controls do not work after
disconnecting from this unit.
Reset the iPod.
• “CANNOT PLAY” appears on the display.
Communication error occurs.
Disconnect and connect the cable to the iPod again.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
• iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
21
EN14-23_KD-PDR45[U]_5.indd 21
11/13/07 12:14:47 PM
ENGLISH
Specifications
AUDIO AMPLIFIER SECTION
Maximum Power Output:
Front/Rear:
50 W per channel
Continuous Power Output (RMS):
Front/Rear:
19 W per channel into 4 Ω, 40 Hz to 20 000 Hz
at no more than 0.8% total harmonic
distortion.
Load Impedance:
4 Ω (4 Ω to 8 Ω allowance)
Tone Control Range:
Bass:
±12 dB (60 Hz, 80 Hz, 100 Hz, 120 Hz)
Mid-range:
±12 dB (500 Hz, 1 kHz, 1.5 kHz, 2.5 kHz)
Treble:
±12 dB (7.5 kHz, 10 kHz, 12.5 kHz, 15 kHz)
Q (Q-slope):
Q0.5 to Q2.0
Frequency Response:
40 Hz to 20 000 Hz
Signal-to-Noise Ratio:
70 dB
Line-Out Level/Impedance:
2.5 V/20 kΩ load (full scale)
Subwoofer-Out Level/Impedance:
2.5 V/20 kΩ load (full scale)
Output Impedance:
1 kΩ
Other Terminal:
AUX (auxiliary) input jack, iPod connector
TUNER SECTION
Frequency Range:
FM Tuner
AM Tuner
FM:
87.5 MHz to 108.0 MHz
AM:
531 kHz to 1 602 kHz
Usable Sensitivity:
11.3 dBf (1.0 μV/75 Ω)
50 dB Quieting Sensitivity:
16.3 dBf (1.8 μV/75 Ω)
Alternate Channel Selectivity (400 kHz):
65 dB
Frequency Response:
40 Hz to 15 000 Hz
Stereo Separation:
30 dB
Sensitivity:
20 μV
Selectivity:
35 dB
22
EN14-23_KD-PDR45[U]_7.indd 22
11/27/07 9:03:31 AM
Type:
Compact disc player
Signal Detection System:
Non-contact optical pickup
(semiconductor laser)
Number of Channels:
2 channels (stereo)
Frequency Response:
5 Hz to 20 000 Hz
Dynamic Range:
96 dB
Signal-to-Noise Ratio:
98 dB
Wow and Flutter:
Less than measurable limit
ENGLISH
CD PLAYER SECTION
MP3 Decoding Format:
(MPEG1/2 Audio Layer 3)
Max. Bit Rate:
320 kbps
WMA (Windows Media® Audio)
Decoding Format:
Max. Bit Rate:
320 kbps
Operating Voltage:
DC 14.4 V (11 V to 16 V allowance)
GENERAL
Power Requirement:
Grounding System:
Negative ground
Allowable Operating Temperature:
0°C to +40°C
Dimensions (W × H × D): (approx.) Installation Size:
182 mm × 52 mm × 160 mm
Panel Size:
Mass:
188 mm × 58 mm × 6 mm
1.3 kg (excluding accessories)
Design and specifications are subject to change without notice.
23
EN14-23_KD-PDR45[U]_5.indd 23
11/13/07 12:14:49 PM
Having TROUBLE with operation?
Please reset your unit
Refer to page of How to reset your unit
EN, TH
© 2007 Victor Company of Japan, Limited
Rear_KD-PDR45[U]_5.indd 2
1107DTSMDTJEIN
11/2/07 9:23:52 AM
KD-PDR45
Installation/Connection Manual
°“√µ‘¥µ—Èß/§ŸË¡◊Õ°“√µ‘¥µ—Èß
1107DTSMDTJEIN
GET0489-006A
EN, TH
© 2007 Victor Company of Japan, Limited
[U/UH]
ENGLISH
‰∑¬
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does
not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
™ÿ¥ª√–°Õ∫π’ȉ¥È√—∫°“√ÕÕ°·∫∫¡“‡æ◊ËÕ„™Èß“π°—∫√–∫∫ °√–· ‰øøÈ“ “¬¥‘π¢—È«≈∫°√–· µ√ß 12 ‚«≈∑Ï À“°√∂¬πµÏ¢Õߧÿ≥‰¡Ë‰
¥È„™È√–∫∫π’È µÈÕß„™È‡§√◊ËÕß·ª≈ß°√–· ‰ø™Ë«¬ ´÷Ëß “¡“√∂À“´◊ÈÕ‰¥È®“°√È“π¢“¬‡§√◊ËÕ߇ ’¬ß√∂¬πµÏ JVC
WARNINGS
§”‡µ◊Õπ
To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all
electrical connections before installing the unit.
• Be sure to ground this unit to the car’s chassis again after installation.
‡æ◊ËÕªÈÕß°—π°“√‡°‘¥‰øøÈ“≈—¥«ß®√ ¢Õ·π–π”„ÀȪ≈¥¢—È«·∫µ‡µÕ√’Ë≈∫ÕÕ° ·≈È«®÷ßµËÕ “¬‰ø°ËÕ𵑥µ—È߇§√◊ËÕß
• µ√«® Õ∫„ÀÈ·πË„®«Ë“‰¥È‡¥‘𠓬¥‘πµËÕ√–À«Ë“߇§√◊ËÕß°—∫µ—«∂—ß √∂¬πµÏ„À¡Ë·≈È«À≈—ß®“°µ‘¥µ—Èß
Notes:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio
dealer.
• It is recommended to connect speakers with a maximum power of more than 50 W (both at the rear and
at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 50 W, change “AMP
GAIN” setting to prevent the speakers from being damaged (see page 15 of the INSTRUCTIONS).
• To prevent short circuits, cover the terminals of the UNUSED leads with insulating tape.
• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.
À¡“¬‡Àµÿ:
• „™Èæ‘°—¥®”‡æ“–·∑πøî« À“°øî« Ï¢“¥∫ËÕ¬ „ÀȪ√÷°…“√È“ π¢“¬‡§√◊ËÕ߇ ’¬ß√∂¬πµÏ JVC
• ¢Õ·π–π”„ÀȵËÕ≈”‚æß ∑’Ë¡’°”≈—ߢ—∫ ß ÿ¥‡°‘π°«Ë“ 50 W (∑—ÈߥȓπÀπÈ“·≈–¥È“πÀ≈—ß ¡’§Ë“§«“¡µÈ“π∑“π 4 Ω ∂÷ß 8 Ω)
∂È“°”≈—ߢ—∫µË”°«Ë“ 50 W „Àȇª≈’ˬπ§Ë“ “AMP GAIN” ‡æ◊ËÕªÈÕß°—π‰¡Ë„ÀÈ≈”‚æß™”√ÿ¥ (¥ŸÀπÈ“ 15 §”·π–π”)
• °“√ªÈÕß°—π°“√≈—¥«ß®√ ®–µÈÕßæ—π¢—È« “¬µ–°—Ë« ∑’ˉ¡Ë„™È·≈È«¥È«¬‡∑ ªæ—𠓬‰ø
• ·ºËπ√–∫“¬§«“¡√ÈÕπ®–√ÈÕπ¡“°À≈—ß®“°„™È √–¡—¥√–«—ßլ˓‰ª —¡º— ‡¡◊ËÕ∂Õ¥™ÿ¥ª√–°Õ∫π’È
Heat sink / ·ºËπ√–∫“¬§«“¡√ÈÕπ
PRECAUTIONS on power supply and speaker connections:
¢ÈÕ§«√√–«—ß ”À√—∫°“√µËÕ·À≈Ë߮˓¬°”≈—ß·≈–≈”‚æß:
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit
will be seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in
your car.
•
Parts list for installation and connection
√“¬°“√ Ë«πª√–°Õ∫ ”À√—∫µ‘¥µ—Èß·≈–‡™◊ËÕ¡µËÕ°—π
The following parts are provided for this unit. If any item is missing, consult your JVC car audio dealer
immediately.
Ë«πª√–°Õ∫µËÕ‰ªπ’È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È À“°¡’ ‘Ëß„¥‰¡Ë§√∫ °√ÿ≥“ª√÷°…“µ—«·∑π®”ÀπË“¬‡§√◊ËÕ߇ ’¬ßµ‘¥√∂¬πµÏ JVC ‚¥¬∑—π∑’
լ˓µËÕ “¬µ–°—Ë«‡§‡∫‘≈°”≈—ߢÕß≈”‚æ߇¢È“°—∫·∫µ‡µÕ√’Ë√∂¬πµÏ ¡‘©–π—Èπ ™ÿ¥ª√–°Õ∫®–‰¥È√—∫§«“¡‡ ’¬À“¬¡“°
• °ËÕπ∑’Ë®–µËÕ “¬µ–°—Ë«‡§‡∫‘≈°”≈—ߢÕß≈”‚æ߇¢È“°—∫≈”‚æß „Àȵ√«® Õ∫°“√‡¥‘𠓬‰ø≈”‚æß„π√∂¢Õߧÿ≥„Àȇ√’¬∫√ÈÕ¬‡ ’¬°ËÕπ
A/B
Hard case/Control panel
C
Sleeve
D
Trim plate
E
Power cord
≈—ß∫√√®ÿ/ÀπÈ“ªí¥
ª≈Õ°ÀÿÈ¡
·ºËπ‚≈À–¢Õ∫·µËß
“¬‡§‡∫‘≈°”≈—ß
F
Direct connection cable for iPod
G
Washer (ø5)
H
Lock nut (M5)
I
Mounting bolt (M4 × 5 mm; M5 × 12.5 mm)
”À√—∫°“√µËÕ “¬ iPod ‚¥¬µ√ß
ª√–‡°Áπ«ß·À«π (ø5)
πÕµ≈ÁÕ§ (M5)
≈—°µ‘¥ (M4 × 5 ¡¡.;
M5 × 12.5 ¡¡.)
J
Rubber cushion
K
Handles
L
Remote controller
M
Battery
¬“ß°—π°√–·∑°
§—π∫—ߧ—∫
√’‚¡µ§Õπ‚∑√≈
·∫µ‡µÕ√
1
Install1-2 KD-PDR45 TH.indd 1
11/27/07 3:24:36 PM
INSTALLATION (IN-DASH MOUNTING)
°“√µ‘¥µ—Èß (°“√ª√–°Õ∫·ºßÀπÈ“ªí∑¡Ï‡¢È“)
The following illustration shows a typical installation. If you have any questions or require information
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
¿“æµ—«Õ¬Ë“ßµËÕ‰ªπ’È· ¥ß∂÷ß°“√µ‘¥µ—Èß·∫∫∑—Ë«‰ª À“°§ÿ≥¡’ªí≠À“À√◊ÕµÈÕß°“√¢ÈÕ¡Ÿ≈‡°’ˬ«°—∫™ÿ¥µ‘¥µ—Èß °√ÿ≥“ª √÷°…“°—∫ºŸÈ¢“¬‡§√◊ËÕ߇ ’
¬ß√∂¬πµÏ JVC ¢Õß∑Ë“πÀ√◊Õ∫√‘…—
• ™ÿ¥ª√–°Õ∫ ∂È“§ÿ≥‰¡Ë·πË„®«Ë“µ‘¥µ—Èß™ÿ¥ª√–°Õ∫π’È∂Ÿ°µÈÕßÀ√◊Õ‰¡Ë „ÀÈÀ“™Ë“ߺŸÈ‡™’ˬ«™“≠‡ªìπºŸÈµ‘¥µ—Èß
Do the required electrical connections.
µËÕ “¬‰øµ“¡∑’Ë°”À𥉫È∑—ÈßÀ¡¥
Bend the appropriate tabs to hold the
sleeve firmly in place.
ßÕ·ºËπ‡æ◊ËÕ¬÷¥ª≈Õ°„ÀȵËÕ°—π‡¢È“∑’Ë
Removing the unit
°“√∂Õ¥™ÿ¥ª√–°Õ∫
Before removing the unit, release the rear section.
°ËÕπ®–∂Õ¥™ÿ¥ª√–°Õ∫ „ÀȪ≈¥ÀπÈ“µ—¥ Ë«π∑È“¬°ËÕπ
Insert the two handles, then pull them as
illustrated so that the unit can be removed.
„ ˧—π∫—ߧ—∫ 2 Õ—π≈ß„π√ËÕß ”À√—∫„™Èæ—π≈«¥ ¥—ß¿“æ ®“°π—Èπ
„Àȇ≈◊ËÕπ™ÿ¥ª√–°Õ∫ÕÕ° „π¢≥–∑’˧ËÕ¬ Ê ¥÷ߧ—π∫—ߧ—∫∑—Èß Õß
Õ—πÕÕ°®“°°—π
When using the optional stay / ‡¡◊ËÕ„™Èµ—«¬÷¥·∫∫‡≈◊Õ°‰¥È
When installing the unit without using the sleeve / ‡¡◊ËÕµ‘¥µ—Èß™ÿ¥ª√–°Õ∫‚¥¬‰¡Ë„™Èª≈Õ°ÀÿÈ¡
In a Toyota car for example, first remove the car radio and install the unit in its place.
Stay (option)
µ—«Õ¬Ë“߇™Ëπ „π√∂¬πµÏ‚µ‚¬µÈ“ „ÀÈ∂Õ¥«‘∑¬ÿµ‘¥√∂¬πµÏÕÕ°°ËÕπ ·≈ô«®÷ßµ‘¥µíô߇§√◊ËÕßπ’ô‡¢ô“·∑π∑’Ë
µ—«¬÷¥ (‡≈◊Õ°‰¥È)
Fire wall
ºπ—ß°—π‰ø
Flat head screws (M5 × 8 mm)*2
°√ŸÀ—«·∫π (M5 × 8 ¡¡.) *2
Dashboard
·ºßÀπÈ“ªí∑¡á
Bracket*2
·∑Ëπ√Õß√—∫*2
Screw (option)
°√Ÿ (‡≈◊Õ°‰¥È)
Flat head screws (M5 × 8 mm)*2
°√ŸÀ—«·∫π (M5 × 8 ¡¡.) *2
Pocket
°–‡ª“–
Bracket *2
·∑Ëπ√Õß√—∫*2
Install the unit at an angle of less than 30˚.
µ‘¥µ—Èß™ÿ¥ª√–°Õ∫∑’Ë¡ÿ¡µË”°«Ë“ 30˚ Õß»“
Note
: When installing the unit on the mounting bracket, make sure to use the 8 mm -long screws. If longer screws are
used, they could damage the unit.
À¡“¬‡Àµ
:
‡¡◊ËÕµ‘¥µ—Èß™ÿ¥ª√–°Õ∫≈ß„π·∑Ëπ√Õß√—∫‰«È „ÀÈ„™È °√Ÿ¬“«¢π“¥ 8 ¡¡. ∂È“„™È °√Ÿ¬“«°«Ë“π’ÈÕ“®∑”„ÀÈ™ÿ¥ª√–°Õ∫‡ ’¬À“¬‰¥ô
*1 When you stand the unit, be careful not to damage the fuse on the rear.
*2 Not supplied for this unit.
*1 ‡¡◊ËÕ§ÿ≥µ—Èß™ÿ¥ª√–°Õ∫¢÷Èπ √–«—ßլ˓∑”„ÀÈøî« Ï∫√‘‡«≥ Ë«π∑È“¬‡ ’¬À“¬
*2 ‰¡Ë ‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È
2
Install1-2 KD-PDR45 TH.indd 2
11/27/07 3:24:43 PM
ENGLISH
‰∑¬
ELECTRICAL CONNECTIONS
A
°“√‡™◊ËÕ¡‚¥¬„™È ‰øøÈ“
Typical connections / °“√‡™◊ËÕ¡µËÕ·∫∫ª°µ
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious
damage to this unit.
The leads of the power cord and those of the connector from the car body may be different in color.
°ËÕ•∑”°“•‡™•ËÕ¡µËÕ: µ•«®†Õ•°“•‡¥‘•†“¬‰ø„•••¬•µÏլ˓ߕ–¡—¥•–«—լ˓„ÀȺ‘¥æ•“¥„•°“•‡™•ËÕ¡µËÕ™ÿ¥ª•–°Õ•™ÿ¥•’
°“•‡™•ËÕ¡µËÕº‘¥æ•“¥Õ“®∑”„Àȇ°‘¥§«“¡‡†’¬À“¬•È“¬·•ß°—•™ÿ¥ª•–
°Õ••’ȉ¥È“•µ–°—Ë«¢Õ߆“¬‰ø ·•–¢ÕßÕÿª°••ÏµËÕ‡™•ËÕ¡®“°µ—«• ß••Õ“®¡’’ ∑’ˉ¡Ë‡À¡•Õ•°—
1
2
3
1 µËÕ “¬‰ø ’µ“¡≈”¥—∫∑’Ë√–∫ÿ„π√Ÿª¥È“π≈Ë“ß
2 ‡™◊ÕË ¡µËÕ°—∫“¬Õ“°“»
3 ÿ¥∑È“¬ µËÕ Ë«π§«∫§ÿ¡°“√‡¥‘𠓬‰ø‡¢È“°—∫™ÿ¥ª√–°Õ∫™ÿ¥π’È
Connect the colored leads of the power cord in the order specified in the illustration below.
Connect the antenna cord.
Finally connect the wiring harness to the unit.
Line out (see diagram
“¬ÕÕ° (¥Ÿ·ºπ¿Ÿ¡
)
)
Rear ground terminal
®ÿ¥‡™◊ËÕ¡µËÕ “¬¥‘π¥È“πÀ≈—ß
15 A fuse
Antenna terminal
ø‘« Ï¢π“¥ 15 A
µ—«‡™◊ËÕ¡ “¬Õ“°“»
iPod connector (see diagram
¢âÕµËÕ iPod (¥Ÿ·ºπ¿Ÿ¡ )
)
Ignition switch
«‘∑™Ï®ÿ¥√–‡∫‘¥
Black
’¥”
To the metallic body or chassis of the car
µËÕ°—∫‚§√ß‚≈À–À√◊Õ‡™ ´‘ ¢Õß√∂¬πµá
Yellow *2
’‡À≈◊Õß *2
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
µËÕ°—∫¢—È«∑’Ë¡’°√–· ‰øøÈ“„π·ºßøî« Ï ´÷ËßµËÕ°—∫·∫µ‡µÕ√’Ë√∂¬πµ
( ‚¥¬‰¡ËµÈÕß„™È «‘∑™Ï®ÿ¥√–‡∫‘¥) (12 ‚«≈∑ϧß∑’Ë)
Fuse block
·ºßø‘« Red
’·¥ß
To an accessory terminal in the fuse block
µËÕ°—∫¢—È« Ë«πª√–°Õ∫„π·ºßø‘«
Blue
»’øÈ“
To the automatic antenna if any (250 mA max.)
‡ “Õ“°“»‰øøÈ“Õ—µ‚π¡—µ‘ À“°¡’ (¢π“¥ Ÿß ¸¥ 250 mA)
Blue with white stripe
’πÈ”‡ß‘π≈“¬¢“«
To the remote lead of other equipment (200 mA max.)
µËÕ‡¢È“°—∫Õª°√≥ÏÕË◊π (¢π“¥ Ÿß ¸¥
200 mA)
White with black stripe
White
Gray with black stripe
Gray
Green with black stripe
Green
Purple with black stripe
Purple
’¢“«·∂∫¥”
’¢“«
’‡∑“·∂∫¥”
’‡∑“
’‡¢’¬«·∂∫¥”
’‡¢’¬«
’¡Ë«ß·∂∫¥”
’¡Ë«ß
Left speaker (front)
Right speaker (front)
Left speaker (rear)
Right speaker (rear)
≈”‚æß´È“¬ (ÀπÈ“)
≈”‚æߢ«“ (ÀπÈ“)
≈”‚æß´È“¬ (À≈—ß)
≈”‚æߢ«“ (À≈—ß)
*1 Not supplied for this unit.
*2 Before checking the operation of this unit prior to installation, this lead must be connected, otherwise the
*1 ‰¡Ë ‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È
*2 °ËÕπ°“√µ√«® Õ∫°“√∑”ß“π¢Õß™ÿ¥ª√–°Õ∫π’È°ËÕπ∑’Ë®–µ‘¥µ—Èß µÈÕßµËÕ “¬µ–°—Ë«π’È°ËÕπ¡‘©–π—Èπ®–‰¡ “¡“√∂‡ªî¥‡§√◊ËÕ߉¥
power cannot be turned on.
3
Install3-4 KD-PDR45 TH.indd 3
11/14/07 11:38:57 AM
B
Connecting the external amplifier or subwoofer / µËÕ·Õ¡ª≈‘ø“¬‡ÕÕ√ÏÀ√◊Õ´—∫«Ÿø‡øÕ√ϥȓππÕ
You can connect an amplifier to upgrade your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it
can be controlled through this unit.
• Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker
leads of this unit unused.
§ÿ≥ “¡“√∂µËÕ°—∫·Õ¡æ≈‘ø“¬‡ÕÕ√Ï ‡æ◊ËÕ‡æ‘Ë¡§ÿ≥ ¿“æ‡ ’¬ß„ÀÈ°—∫√–∫∫ ‡µÕ√‘‚Õ¢Õß√∂¬πµÏ
µËÕ “¬µ–°—Ë«√–¬–‰°≈ ( ’πÈ”‡ß‘π≈“¬¢“«) ‡¢È“°—∫ “¬µ–°—Ë«√–¬–‰°≈¢ÕßÕÿª°√≥ÏÕ◊Ëπ Ê ‡æ◊ËÕ®– “¡“√∂§«∫§ÿ¡‚¥¬™ÿ¥ª√–
°Õ∫π’ȉ¥È
• ∂Õ¥≈”‚æßÕÕ°®“°™ÿ¥ª√–°Õ∫π’È ·≈È«µËÕ‡¢È“°—∫‡§√◊ËÕߢ¬“¬ ∑‘Èß “¬µ–°—Ë«≈”‚æߢÕß™ÿ¥ª√–°Õ∫πïô‰«È
•
Remote lead
Y-connector (not supplied for this unit)
“¬µ–°—Ë«•–¬–‰°•
¢ÈÕµËÕ√Ÿªµ—« Y ( ‰¡Ë ‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È)
Remote lead (blue with white stripe)
“¬µ–°—Ë«•–¬–‰°• ( ’πÈ”‡ß‘π≈“¬¢“«)
Set “L/O MODE” to “REAR” (See page 15 of the
INSTRUCTIONS.)
To the remote lead of other equipment or automatic
antenna if any
µ—Èߧ˓ “L/O MODE” ‡ªìπ “REAR” (¥ŸÀπÈ“ 15 §”·π–π”)
µËÕ “¬°—∫Õÿª°√≥ÏÕ◊ËπÀ√◊Õ‡ “Õ“°“»Õ—µ‚π¡—µ‘∂È“¡’
Rear speakers
≈”‚æßÀ≈—ß
JVC Amplifier
‡§√◊ËÕߢ¬“¬‡ ’¬ß JVC
Signal cord (not supplied for this unit).
Set “L/O MODE” to “SUB.W” (See page 15 of the
INSTRUCTIONS.)
“¬‡§‡∫‘≈ —≠≠“≥ ( ‰¡Ë ‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È)
Front speakers
µ—Èߧ˓ “L/O MODE” ‡ªìπ “SUB.W” (¥ŸÀπÈ“ 15 §”·π–π”)
≈”‚æßÀπÈ“
or
Subwoofer
´—∫«Ÿø‡øÕ√Ï
C
JVC Amplifier
‡§√◊ËÕߢ¬“¬‡ ’¬ß JVC
À√◊Õ
Connecting an Apple iPod / °“√‡™◊ËÕ¡µËÕ°—∫ Apple iPod
You can connect an iPod to this unit using the supplied direct connection cable for iPod.
∑Ë“π “¡“√∂‡™◊ËÕ¡µËÕ iPod °—∫‡§√◊ËÕ߇≈Ëππ’È ‰¥È‚¥¬°“√„™È “¬‡™◊ËÕ¡µËÕ‚¥¬µ√ß ”À√—∫ iPod
Apple iPod (separately purchased)
Apple iPod (·¬°®”ÀπË“¬)
iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
iPod ‡ªÁπ‡§√◊ËÕßÀ¡“¬°“√§È“¢Õß Apple Inc.
Direct connection cable for iPod (supplied)
”À√—∫°“√µËÕ “¬ iPod ‚¥¬µ√ß (¡’¡“„ÀÈ)
™÷Ëß®¥∑–‡∫’¬π°“√§È“„πª√–‡∑» À√—∞Õ‡¡√‘°“·≈–ª√–‡∑»Õ◊ËπÊ
*3 Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint
*3 µËÕ≈«¥ “¬¥‘π„ÀÈ·πËπ‡¢È“°—∫µ—«∂—߇À≈Á° À√◊Õµ—«∂—ß√∂—µ√ß Ë«π ∑’ˉ¡Ë¡ ’ ’‡§≈◊Õ∫ (À“°¡’ ’‡§≈◊Õ∫Õ¬ŸË „ÀÈ¢Ÿ¥ ’ÕÕ°°ËÕπ °ËÕπµËÕ≈«¥ “¬¥‘π)
(if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the
unit.
À“°‰¡ËªØ‘∫—µ‘µ“¡§”·π–π”π’È ‡§√◊ËÕßÕ“®™”√ÿ¥À√◊Õ‡ ’¬À“¬‰¥
TROUBLESHOOTING
°“√µ√«® Õ∫ªí ≠À“¢—¥¢ÈÕß
• The fuse blows.
* Are the red and black leads connected correctly?
•
*
øî« Ï¢“¥
¡’°“√‡™◊ËÕ¡ “¬µ–°—Ë« ’¥”·≈– ’·¥ßլ˓ß∂Ÿ°µÈÕßÀ√◊Õ‰¡Ë
• Power cannot be turned on.
* Is the yellow lead connected?
•
*
‰¡Ë “¡“√∂‡ªî¥‡§√◊ËÕ߉¥È
¡’°“√‡™◊ËÕ¡ “¬µ–°—Ë« ’‡À≈◊ÕßÀ√◊Õ‰¡Ë
• No sound from the speakers.
* Is the speaker output lead short-circuited?
•
*
‰¡Ë¡’‡ ’¬ßÕÕ°®“°≈”‚æß
“¬µ–°—Ë« Ë«π∑’ËÕÕ°∑“ß≈”‚æ߇°‘¥‰øøÈ“≈—¥«ß®√À√◊Õ‰¡Ë
•
*
*
‡ ’¬ß‡æ’Ȭπ
“¬µ–°—Ë« Ë«π∑’ËÕÕ°∑“ß≈”‚æßµËÕ≈ߥ‘πÀ√◊Õ‰¡Ë
“¬¢—È«≈∫ “–” ¢Õß≈”‚æߥȓπ´È“¬·≈–¢«“µËÕ≈ߥ‘πµ“¡ª°µ‘À√◊Õ‰¡Ë
•
*
‡ ’¬ß√∫°«π
¡’°“√„™È “¬ —ÈπÊ À√◊ÕÀπ“Ê µËÕ®“°‡§√◊ËÕß «π∑’˵‘¥µ—Èß ‰«È∫πæ◊Èπ¥È“πÀ≈—ß°—∫µ—«∂—ß√∂¬πµÏÀ√◊Õ‰¡Ë
•
*
*
™ÿ¥ª√–°Õ∫√ÈÕπ¢÷Èπ
“¬µ–°—Ë« Ë«π∑’ËÕÕ°∑“ß≈”‚æßµËÕ≈ߥ‘πÀ√◊Õ‰¡Ë
“¬¢—È«≈∫ “–” ¢Õß≈”‚æߥȓπ´È“¬·≈–¢«“µËÕ≈ߥ‘πµ“¡ª°µ‘À√◊Õ‰¡Ë
•
*
‡§√◊ËÕß√—∫π’È∑”ß“π‰¡
∑Ë“π‰¥Èµ—È߇§√◊ËÕß„À¡Ë·≈È«À√◊Õ¬—ß
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• Noise interfere with sounds.
* Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?
• This unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• This unit does not work at all.
* Have you reset your unit?
4
Install3-4 KD-PDR45 TH.indd 4
11/14/07 11:39:07 AM
CD RECEIVER
KD-PDR45
ENGLISH
ALAT PENERIMA CD
KD-PDR45
INDONESIA
For canceling the display demonstration, see page 6.
Untuk membatalkan tampilan demonstrasi, lihat halaman 6.
For installation and connections, refer to the separate manual.
Untuk instalasi dan penyambungan, lihat buku pedoman terpisah.
INSTRUCTIONS
BUKU PETUNJUK
GET0489-004A
[UN]
Cover_KD-PDR45[U]_004A.indd 1
7/25/07 10:44:16 AM
ENGLISH
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best
possible performance from the unit.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to
qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical
instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
Detaching the control panel
[European Union only]
Warning:
If you need to operate the unit while driving, be
sure to look around carefully or you may be involved
in a traffic accident.
Attaching the control panel
2
EN02-05_KD-PDR45[U]_5.indd 2
11/2/07 8:56:33 AM
CONTENTS
Control panel .................................. 4
Remote controller — RM-RK50........... 5
Getting started ................................ 6
ENGLISH
How to reset your unit
Basic operations ................................................... 6
• Your preset adjustments will also be erased.
Radio operations ............................. 7
Disc operations ................................ 8
Playing a disc in the unit ..................................... 8
How to forcibly eject a disc
• Be careful not to drop the disc when it ejects.
• If this does not work, reset your unit.
How to use the M MODE button
If you press M MODE, the unit goes into functions mode,
then the number buttons and 5/∞ buttons work as
different function buttons.
Ex.: When number button 2 works as
MO (monaural) button.
iPod operations ...............................
Sound adjustments ..........................
General settings — PSM ..................
Other external component
operations ...................................
Title assignment..............................
Maintenance ...................................
More about this unit ........................
Troubleshooting ..............................
Specifications ..................................
10
12
14
16
16
17
17
20
22
For safety...
• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
• Stop the car before performing any complicated
operations.
Temperature inside the car...
To use these buttons for their original functions
again after pressing M MODE, press M MODE again.
• Waiting for about 5 seconds without pressing any of
these buttons will automatically cancels the functions
mode.
If you have parked the car for a long time in hot or cold
weather, wait until the temperature in the car becomes
normal before operating the unit.
3
EN02-05_KD-PDR45[U]_5.indd 3
11/2/07 8:56:34 AM
ENGLISH
Control panel
Parts identification
Display window
1
2
3
4
5
6
7
8
9
p
q
w
e
r
t
y
u
i
5 (up) / ∞ (down) buttons
0 (eject) button
(standby/on attenuator) button
Control dial
Remote sensor
DO NOT expose the remote sensor to strong light
(direct sunlight or artificial lighting).
BAND button
Loading slot
Display window
EQ (equalizer) button
DISP (display) button
(control panel release) button
i (iPod) button
4 /¢ buttons
SRC (source) button
SEL (select) button
M MODE button
MO (monaural) button
SSM (Strong-station Sequential Memory) button
o
;
a
s
d
f
g
h
j
k
l
/
z
x
Number buttons
RPT (repeat) button
RND (random) button
AUX (auxiliary) input jack
Source display / Track number / Folder number /
Time countdown indicator
Tr (track) indicator
DISC indicator
Playback mode / item indicators— RND (random),
(disc), (folder), RPT (repeat)
Tuner reception indicators—ST (stereo),
MO (monaural)
Sound mode (iEQ: intelligent equalizer) indicators
—CLASSIC, HIP HOP, JAZZ, ROCK, POPS, USER
LOUD (loudness) indicator
EQ (equalizer) indicator
Disc information indicators—
TAG (Tag information), (folder), (track/file)
Main display
4
EN02-05_KD-PDR45[U]_5.indd 4
11/2/07 8:56:35 AM
Remote controller — RM-RK50
ENGLISH
Main elements and features
Installing the lithium coin battery
(CR2025)
1
2
Aim the remote controller directly at the remote
sensor on the unit. Make sure there is no obstacle
in between.
Warning:
• Do not install any battery other than CR2025 or its
equivalent; otherwise, it may explode.
• Do not leave the remote controller in a place
(such as the dashboard) exposed to direct
sunlight for a long time; otherwise, it may
explode.
• Store the battery in a place where children cannot
reach to avoid the risk of accidents.
• To prevent the battery from over-heating,
cracking, or starting a fire:
– Do not recharge, short, disassemble, heat the
battery, or dispose of it in a fire.
– Do not leave the battery with other metallic
materials.
– Do not poke the battery with tweezers or
similar tools.
– Wrap the battery with tape and insulate when
throwing away or saving it.
3
4
5
6
(standby/on/attenuator) button
• Turns the power on if pressed briefly or
attenuates the sound when the power is on.
• Turns the power off if pressed and held.
5 U (up) / D (down) ∞ buttons
• Changes the FM/AM bands with 5 U.
• Changes the preset stations with D ∞.
• Changes the folder of the MP3/WMA discs.
• While listening to an Apple iPod.
– Enters the main menu if pressed and held.
(Now 5 U/D ∞/2 R/F 3 work as the menu
selecting buttons.)
• While listening to an iPod (in menu selecting
mode):
– Selects an item if pressed D ∞ briefly. (Then,
press and hold D ∞ to play back the selection
directly.)
– Returns to the previous menu if pressed 5 U
briefly.
VOL – / VOL + buttons
• Adjusts the volume level.
SOUND button
• Selects the sound mode (iEQ: intelligent
equalizer).
SOURCE button
• Selects the source.
2 R (reverse) / F (forward) 3 buttons
• Searches for stations if pressed briefly.
• Fast-forwards or reverses the track if pressed and
held.
• Changes the track if pressed briefly.
• While listening to an iPod (in menu selecting
mode):
– Accelerated file search: Hold 2 R/F 3 to fast
skip during song search in the main menu.
5
EN02-05_KD-PDR45[U]_7.indd 5
11/20/07 12:16:46 PM
ENGLISH
Getting started
Basic operations
~
Turn on the power.
To drop the volume in a
moment (ATT)
To restore the sound, press
the button again.
To turn off the power
Ÿ
Basic settings
• See also “General settings — PSM” on pages
14 and 15.
1
*1 You cannot select “CD” as the playback source
if there is no disc in the unit.
*2 “NO IPOD” appears if an iPod is not connected.
!
2
For FM/AM tuner
1 Canceling the display demonstrations
Select “DEMO,” then “DEMO OFF.”
2 Setting the clock
⁄
Select “CLOCK HOUR,” then adjust the hour.
Select “CLOCK MIN” (minute), then adjust the
minute.
Adjust the volume.
3
Volume level appears.
@
Adjust the sound as you want. (See
pages 12 and 13.)
Finish the procedure.
To check the current clock time while the
power is turned off
Clock time is shown on the display for
about 5 seconds. See also page 14.
Caution on volume setting:
Discs produce very little noise compared with other
sources. Lower the volume before playing a disc
to avoid damaging the speakers by the sudden
increase of the output level.
6
EN06-13_KD-PDR45[U]_5.indd 6
11/2/07 8:56:47 AM
When an FM stereo broadcast is hard to
receive
~
Lights up when monaural mode is activated.
Ÿ
Reception improves, but the stereo effect will be lost.
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
!
ENGLISH
Radio operations
To restore the stereo effect, repeat the same
procedure. “MONO OFF” appears and the MO indicator
goes off.
Storing stations in memory
Start searching for a station.
You can preset six stations for each band.
When a station is received, searching stops.
To stop searching, press the same button
again.
FM station automatic presetting—
SSM (Strong-station Sequential
Memory)
1
Select the FM band (FM1 – FM3) you want to
store into.
To tune in to a station manually
In step ! above...
1
2
3
2 Select a desired station frequency.
“SSM” flashes, then disappears when automatic
presetting is over.
Local FM stations with the strongest signals are
searched and stored automatically in the FM band.
7
EN06-13_KD-PDR45[U]_5.indd 7
11/2/07 8:56:48 AM
ENGLISH
Manual presetting
Ex.: Storing the FM station of 92.50 MHz into preset
number 4 of the FM1 band.
1
Disc operations
Playing a disc in the unit
All tracks will be played repeatedly until you change the
source or eject the disc.
2
3
To stop play and eject the disc
Preset number flashes for a while.
Listening to a preset station
1
2
• Press SRC to listen to another
playback source.
[Hold] To fast-forward or reverse the
track
Select the preset station (1 – 6) you want.
[Press] To go to the next or previous
track
or
[Press] To go to the next or previous
folder (only for MP3 or WMA
discs)
To locate a particular track (for CD) or folder
(for MP3 or WMA discs) directly
To check other information while listening
to the radio
Frequency = Clock =
Station name * = (back to the
beginning)
To select a number from 01 – 06:
To select a number from 07 – 12:
* If no title is assigned to a station, “NO NAME” appears.
To assign a title to a station, see page 16.
8
EN06-13_KD-PDR45[U]_5.indd 8
11/2/07 8:56:49 AM
To select a particular track in a folder
(for MP3 or WMA discs):
Changing the display information
While playing an audio CD or CD Text
ENGLISH
• To use direct folder access on MP3/WMA discs, it
is required that folders are assigned with 2-digit
numbers at the beginning of their folder names—
01, 02, 03, and so on.
A = B = Disc title/performer *1 = Track
title *1 [ ] = (back to the beginning)
Other main functions
Skipping tracks quickly during play
• For MP3 or WMA discs, you can skip tracks within the
same folder.
Ex.: To select track 32 while playing a track whose
number is a single digit (1 to 9)
While playing an MP3 or a WMA track
• When “TAG DISPLAY” is set to “TAG ON”
(see page 15)
A = B = Album name/performer (folder
name *2) [
] = Track title (file
name *2) [
] = (back to the beginning)
• When “TAG DISPLAY” is set to “TAG OFF”
1
A = B = Folder name [ ] = File name
[ ] = (back to the beginning)
2
Each time you press the button, you can skip 10
tracks.
• After the last track, the first track will be selected
and vice versa.
3
A : Current track number with the elapsed playing
time
B : Current track number with the clock time
[ ] : Corresponding indicator lights up on the display.
*1 If the current disc is an audio CD, “NO NAME” appears.
*2 If an MP3/WMA file does not have Tag information,
folder name and file name appear. In this case, the
TAG indicator will not light up.
Prohibiting disc ejection
You can lock a disc in the loading slot.
“EJECT LOCK” flashes on the display.
To cancel the prohibition, repeat the same
procedure.
9
EN06-13_KD-PDR45[U]_5.indd 9
11/2/07 8:56:49 AM
ENGLISH
Selecting the playback modes
You can use only one of the following playback modes
at a time.
1
2
Select your desired playback mode.
iPod operations
You can play songs in an Apple iPod by connecting it
with the supplied direct connection cable for iPod.
You can control playback from the unit or from your
iPod.
• Disconnecting the iPod will stop playback. Press SRC
to listen to another playback source.
Caution:
7 Repeat play
Mode
Plays repeatedly
]
TRACK RPT : The current track. [
FOLDER RPT * : All tracks of the current folder.
[
]
RPT OFF
: Cancels.
7 Random play
Mode
Plays at random
• Avoid using the iPod if it might hinder your safety
while driving.
• Make sure all important data has been backed up
to avoid losing the data.
• For connection, see the Installation/Connection
Manual (separate volume).
• For details, refer also to the manual supplied for your
iPod.
~
Connect an iPod.
Direct connection
cable for iPod
FOLDER RND *: All tracks of the current folder,
then the tracks of the next folder
and so on. [
]
ALL RND
: All tracks of the current disc.
[
]
RND OFF
: Cancels.
* Only while playing an MP3 or a WMA disc.
If an iPod has been connected...
To directly select “IPOD” as the source
while listening to another source or
when the power is turned off.
[ ] : Corresponding indicator lights up on the
display.
Playback starts automatically from where it had
been paused previously.
Ÿ
Adjust the volume.
10
EN06-13_KD-PDR45[U]_5.indd 10
11/2/07 8:56:50 AM
Adjust the sound as you want. (See
pages 12 and 13.)
Selecting a track from the menu
1
ENGLISH
!
Enter the main menu.
To control playback from your iPod
or
“IPOD MODE” appears on the
display.
Now the 5/∞/4 /¢ /number
buttons work as the menu selecting buttons.
• Press and hold this button again to control playback
from the unit. “HEAD MODE” appears on the display.
2
Select the desired menu.
Playback control from the unit
[Press] Go to the next or previous
track
[Hold] Fast-forward or reverse the
track during playback
Fast-skip the menu items of
the main menu
PLAYLIST Ô ARTIST Ô ALBUM Ô SONG
Ô PODCASTÔ GENRE Ô COMPOSER Ô
AUDIOBOOK Ô (back to the beginning)
[Hold] Enter the main menu (see the
right column).
[Press] Pause/resume playback.
• Pressing the number buttons can directly select
the desired menu (see the left column for
details).
3
Confirm the selection.
To move back to the previous
menu, press 5.
[Press] Go to the top menu of “PLAYLIST,” “ARTIST,”
“ALBUM,” “SONG,” “PODCAST,” or “GENRE” in
the main menu (see the right column).
[Hold] Go to the top menu of “COMPOSER” or
“AUDIOBOOK” in the main menu (see the
right column).
• Holding the button will start play back the
selected item directly.
• If a track is selected, playback starts
automatically.
• If the selected item has another layer, you will
enter the layer. Repeat steps 2 and 3 until the
desired track is played.
• Accelerated file search: Hold 4 /¢
to fast skip during song search in the main
menu.
Continued on the next page
11
EN06-13_KD-PDR45[U]_7.indd 11
11/20/07 12:49:50 PM
ENGLISH
To exit from menu selecting mode
To check other information while listening
to an iPod
or
* The menu selecting mode will be canceled:
– If no operations are performed for about
10 seconds.
– When you confirm the selection of a track.
– Pressing some other buttons such as DISP, SEL,
MODE, or EQ.
Current track number with the elapsed
playing time = Current track number with
the clock time = Track title * = Album name/
performer * = (back to the beginning)
* When “TAG DISPLAY” is set to “TAG OFF,” file name and
folder name appear.
Selecting the playback modes
1
2
Sound adjustments
You can select a preset sound mode suitable to the
music genre (iEQ: intelligent equalizer).
Select your desired playback mode.
7 Repeat play
Mode
ONE RPT
ALL RPT
RPT OFF
Playback functions (as on iPod)
: Same as “Repeat One.” [
: Same as “Repeat All.” [
: Cancels.
Adjusting the sound
]
]
You can adjust the sound characteristics to your
preference.
• The adjustment you make will be stored for the
currently selected sound mode (iEQ) including
“USER.”
7 Random play
Mode
Playback functions (as on iPod)
SONG RND : Same as “Shuffle Songs.” [
ALBUM RND * : Same as “Shuffle Albums.”
[
]
RND OFF
: Cancels.
]
1
2
* Functions only if you select “ALL” in “ALBUMS” of
the main menu
[ ] : Corresponding indicator lights up on the
display.
Indication, [Range]
FADER *2, [R06 to F06]
Adjust the front and rear speaker balance.
BALANCE *3, [L06 to R06]
Adjust the left and right speaker balance.
12
EN06-13_KD-PDR45[U]_7.indd 12
11/20/07 12:23:25 PM
3
Select a sound characteristic.
4
Adjust the sound elements of the selected
sound characteristic.
1 Adjust the frequency.
LOUD *4 (loudness), [LOUD ON or LOUD OFF]
Boost low and high frequencies to produce a
well-balanced sound at a low volume level.
SUBWOOFER *1, [00 to 08, initial: 04]
Adjust the subwoofer output level.
VOL ADJ (volume adjust), [–05 to +05, initial: 00]
Adjust the volume level of each source (except FM), in
relation to the FM volume level. The volume level will
automatically increase or decrease when you change
the source.
• Before making an adjustment, select the source you
want to adjust.
ENGLISH
Indication, [Range]
2 Adjust the level.
VOLUME, [00 to 50 or 00 to 30 ]*5
Adjust the volume.
*1 Displayed only when “L/O MODE” is set to “SUB.W”
(see page 15).
*2 If you are using a two-speaker system, set the fader
level to “00.”
*3 This adjustment will not affect the subwoofer output.
*4 The adjustment made (LOUD ON/LOUD OFF) will be
applied to all sound modes.
*5 Depending on the amplifier gain control setting. (See
page 15 for details.)
3 Adjust the quality slope (Q).
Sound
elements
BASS
MID
TRE
Frequency
60 Hz
80 Hz
100 Hz
120 Hz
500 Hz
1.0 kHz
1.5 kHz
2.5 kHz
7.5 kHz
10.0 kHz
12.5 kHz
15.0 kHz
Level
–06 to
+06
–06 to
+06
–06 to
+06
Q (Q-slope)
Q0.5
Q1.0
Q1.5
Q2.0
Q0.75
Q1.0
Q1.25
Q1.5
Q0.75
Q1.25
Storing your own sound mode
You can adjust the sound modes and store your own
adjustments in memory.
1
2
Range/selectable items
Select a sound mode.
Enter the adjustment mode.
• If no operation is done within
5 seconds, this mode is canceled.
BASS: Bass MID: Mid-range TRE: Treble
5
The adjustment made will be stored
automatically. Repeat steps 3 and 4 to adjust
other sound characteristics.
13
EN06-13_KD-PDR45[U]_7.indd 13
11/20/07 12:23:26 PM
ENGLISH
General settings — PSM
You can change PSM (Preferred Setting Mode) items
listed in the table below and on page 15.
3
Adjust the PSM item selected.
4
Repeat steps 2 and 3 to adjust other PSM
items if necessary.
5
Finish the procedure.
1
2
Select a PSM item.
Indications
Item
( : Initial)
Setting, [reference page]
DEMO
Display
demonstration
• DEMO ON
: The display demonstration will be activated automatically if no
operation is done for about 20 seconds, [6].
: Cancels.
CLOCK DISP *1
Clock display
• CLOCK ON
• DEMO OFF
• CLOCK OFF
: The clock time is shown on the display at all times when the power is
turned off.
: Cancels; pressing DISP will show the clock time for about 5 seconds
when the power is turned off, [6].
CLOCK HOUR
Hour adjustment
1 – 12
[Initial: 1 (1:00)], [6].
CLOCK MIN
Minute adjustment
00 – 59
[Initial: 00 (1:00)], [6].
DIMMER
Dimmer
• ON
• OFF
: Dims the display and button illumination.
: Cancels.
*1 If the power supply is not interrupted by turning off the ignition key of your car, it is recommended that you select
“CLOCK OFF” to save the car’s battery.
14
EN14-23_KD-PDR45[U]_5.indd 14
11/2/07 8:57:02 AM
Item
( : Initial)
Setting, [reference page]
AUDIOBOOKS *2
Speed control of
“Audiobook”
• NORMAL
• FASTER
• SLOWER
: You can select the playback speed of the “Audiobook” sound file in
your iPod.
SCROLL *3
Scroll
• ONCE
• AUTO
• OFF
:
:
:
•
L/O MODE
Line output mode
• REAR
: Select if the REAR LINE OUT terminals are used for connecting the
speakers (through an external amplifier).
: Select if the REAR LINE OUT terminals are used for connecting a
subwoofer (through an external amplifier).
• SUB.W
ENGLISH
Indications
Scrolls the displayed information once.
Repeats scrolling (at 5-second intervals).
Cancels.
Pressing DISP for more than one second can scroll the display
regardless of the setting.
SUB.W FREQ *4
Subwoofer cutoff
frequency
• LOW
• MID
• HIGH
: Frequencies lower than 90 Hz are sent to the subwoofer.
: Frequencies lower than 135 Hz are sent to the subwoofer.
: Frequencies lower than 180 Hz are sent to the subwoofer.
TAG DISPLAY
Tag display
• TAG ON
• TAG OFF
: Shows the Tag information while playing MP3/WMA tracks, [9].
: Cancels.
AMP GAIN
Amplifier gain
control
• LOW POWER
IF BAND
Intermediate
frequency band
• AUTO
: VOLUME 00 – VOLUME 30. (Select this if the maximum power of the
speaker is less than 50 W to avoid damaging the speaker.)
• HIGH POWER : VOLUME 00 – VOLUME 50.
• WIDE
: Increases the tuner selectivity to reduce interference noise between
close stations. (The stereo effect may be lost.)
: Subject to interference noise from adjacent stations, but the sound
quality will not be degraded and the stereo effect will remain.
*2 Displayed only when an iPod is connected and playback is controlled from the unit.
*3 Some characters or symbols will not be shown correctly (or will be blanked) on the display.
*4 Displayed only when “L/O MODE” is set to “SUB.W.”
15
EN14-23_KD-PDR45[U]_5.indd 15
11/2/07 8:57:04 AM
ENGLISH
Other external component
operations
You can connect an external component to the AUX
(auxiliary) input jack on the control panel.
Title assignment
You can assign names to 30 station frequencies (FM and
AM) and up to 8 characters for each station name.
1
Select FM/AM.
2
Show the title entry screen.
3
Assign a title.
1 Select a character.
Portable audio player, etc.
3.5 mm stereo mini
plug (not supplied)
~
Ÿ
!
Turn on the connected component and
start playing the source.
Adjust the volume.
2 Move to the next (or previous) character
position.
⁄
3 Repeat steps 1 and 2 until you finish
Adjust the sound as you want. (See
pages 12 and 13.)
entering the title.
4
Finish the procedure.
To check other information while listening
to an external component
Clock Ô AUX IN
To erase the entire title
In step 2 above...
16
EN14-23_KD-PDR45[U]_5.indd 16
11/2/07 8:57:05 AM
How to clean the connectors
Frequent detachment will deteriorate the connectors.
To minimize this possibility, periodically wipe the
connectors with a cotton swab or cloth moistened with
alcohol, being careful not to damage the connectors.
To play new discs
New discs may have some rough spots
around the inner and outer edges. If
such a disc is used, this unit may reject
the disc.
To remove these rough spots, rub the edges with a
pencil or ball-point pen, etc.
ENGLISH
Maintenance
Do not use the following discs:
Connectors
Single CD (8 cm disc)
Warped disc
Sticker and
sticker residue
Stick-on label
Moisture condensation
Moisture may condense on the lens inside the unit in
the following cases:
• After starting the heater in the car.
• If it becomes very humid inside the car.
Should this occur, the unit may malfunction. In this
case, eject the disc and leave the unit turned on for a
few hours until the moisture has evaporated.
How to handle discs
When removing a disc from its case, press down the
center holder of the case and lift the Center holder
disc out, holding it by the edges.
• Always hold the disc by the edges.
Do not touch its recording surface.
When storing a disc in its case, gently insert the
disc around the center holder (with the printed surface
facing up).
• Make sure to store discs in cases after use
To keep discs clean
A dirty disc may not play correctly.
If a disc does become dirty, wipe it with
a soft cloth in a straight line from center
to edge.
• Do not use any solvents (for example, conventional
record cleaner, spray, thinner, benzine, etc.) to clean
discs..
Unusual shape
More about this unit
Basic operations
Turning on the power
• By pressing SRC (source) or i (iPod) button on the
unit, you can also turn on the power. If the source is
ready, playback also starts.
Turning off the power
• If you turn off the power while listening to a track,
playback will start from where it had been stopped
previously next time you turn on the power.
General
• If you change the source while listening to a disc or
an iPod, playback stops.
Next time you select “CD” or “IPOD” as the playback
source, playback will start from where it had been
stopped/paused previously.
Continued on the next page
17
EN14-23_KD-PDR45[U]_5.indd 17
11/13/07 12:14:43 PM
ENGLISH
• After ejecting a disc or disconnecting an iPod,
“NO DISC” or “NO IPOD” appears and you cannot
operate some of the buttons. Insert another disc,
connect an iPod, or press SRC to select another
playback source.
Tuner operations
Storing stations in memory
• During SSM search...
– All previously stored stations are erased and the
stations are stored anew.
– Received stations are preset in No. 1 (lowest
frequency) to No. 6 (highest frequency).
– When SSM is over, the station stored in No. 1 will
be automatically tuned in.
• When storing a station manually, the previously
preset station is erased when a new station is stored
in the same preset number.
Disc operations
Caution for DualDisc playback
• The Non-DVD side of a “DualDisc” does not comply
with the “Compact Disc Digital Audio” standard.
Therefore, the use of Non-DVD side of a DualDisc on
this product may not be recommended.
General
• This unit has been designed to reproduce
CDs/CD Texts, and CD-Rs (Recordable)/CD-RWs
(Rewritable) in audio CD (CD-DA), MP3 and WMA
formats.
• When a disc is inserted upside down, “PLEASE” and
“EJECT” appear alternately on the display. Press 0 to
eject the disc.
• MP3 and WMA “tracks” (words “file” and “track” are
used interchangeably) are recorded in “folders.”
• While fast-forwarding or reversing on an MP3 or
WMA disc, you can only hear intermittent sounds.
Playing a CD-R or CD-RW
• Use only “finalized” CD-Rs or CD-RWs.
• This unit can only play back files of the same type as
those which are detected first if a disc includes both
audio CD (CD-DA) files and MP3/WMA files.
• This unit can play back multi-session discs; however,
unclosed sessions will be skipped while playing.
• Some CD-Rs or CD-RWs may not play back on this
unit because of their disc characteristics, or for the
following reasons:
– Discs are dirty or scratched.
– Moisture condensation has occurred on the lens
inside the unit.
– The pickup lens inside the unit is dirty.
– The files on the CD-R/CD-RW are written using the
“Packet Write” method.
– There are improper recording conditions (missing
data, etc.) or media conditions (stained, scratched,
warped, etc.).
• CD-RWs may require a longer readout time since the
reflectance of CD-RWs is lower than that of regular
CDs.
• Do not use the following CD-Rs or CD-RWs:
– Discs with stickers, labels, or a protective seal stuck
to the surface.
– Discs on which labels can be directly printed by an
ink jet printer.
Using these discs under high temperature or high
humidity may cause malfunctions or damage to the
unit.
Playing an MP3/WMA disc
• This unit can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of
the letter case—upper/lower).
• This unit can show the names of albums, artists
(performer), and Tag (Version 1.0, 1.1, 2.2, 2.3, or
2.4) for MP3 files and for WMA files.
• This unit can display only one-byte characters. No
other characters can be correctly displayed.
• This unit can play back MP3/WMA files meeting the
conditions below:
– Bit rate: 8 kbps — 320 kbps
18
EN14-23_KD-PDR45[U]_6.indd 18
11/14/07 4:35:31 PM
•
•
•
•
Ejecting a disc
• If the ejected disc is not removed within 15 seconds,
it is automatically inserted into the loading slot again
to protect it from dust. Playback starts automatically.
iPod operations
• Controllable iPod:
– iPod mini
– iPod G4
•
•
•
•
•
•
•
•
•
– iPod photo
– iPod nano (1st & 2nd Generation)
– iPod with video (5th Generation)
Update your iPod to the latest software version
before using it with this unit.
When you turn on this unit, the iPod is charged
through this unit.
While connecting an iPod with Video:
– No video shows on the iPod’s display or the
external monitor (only the audio part is available).
– It is not possible to browse video files on the
“Video“ menu. (If you connect the iPod during
the playback or pausing of a video file, resuming
playback will not work.)
iPod shuffle cannot be used with this unit.
You can control the iPod from this unit when “JVC” or
“ ” appears on the iPod display after connection.
The song order displayed on the selection menu of
this unit may differ from that of the iPod.
If playback is stopped, select a track from the
selection menu or press BAND to playback the same
track again.
The text information may not be displayed correctly:
– Some characters such as accented letters cannot be
shown correctly on the display.
– Communication between the iPod and the unit is
not stable.
If the text information includes more than
11 characters, it scrolls on the display. This unit can
display up to 64 characters.
ENGLISH
•
– Sampling frequency:
48 kHz, 44.1 kHz, 32 kHz (for MPEG-1)
24 kHz, 22.05 kHz, 16 kHz (for MPEG-2)
– Disc format: ISO 9660 Level 1/Level 2, Romeo,
Joliet, Windows long file name
The maximum number of characters for file/folder
names vary depending on the disc format used
(includes 4 extension characters—<.mp3> or
<.wma>).
– ISO 9660 Level 1: up to 12 characters
– ISO 9660 Level 2: up to 31 characters
– Romeo: up to 128 characters
– Joliet: up to 64 characters
– Windows long file name: up to 128 characters
This unit can recognize a total of 512 files,
255 folders, and 8 hierarchical levels.
This unit can play back files recorded in VBR (variable
bit rate).
Files recorded in VBR have a discrepancy in the
elapsed time display, and do not show the actual
elapsed time. In particular, this difference becomes
noticeable after performing the search function.
This unit cannot play back the following files:
– MP3 files encoded in MP3i and MP3 PRO format.
– MP3 files encoded in an inappropriate format.
– MP3 files encoded with Layer 1/2.
– WMA files encoded in lossless, professional, and
voice format.
– WMA files which are not based upon Windows
Media® Audio.
– WMA files copy-protected with DRM.
– Files which have data such as AIFF, ATRAC3, etc.
The search function works but search speed is not
constant.
Notice:
When operating an iPod, some operations may not
be performed correctly or as intended. In this case,
visit the following JVC web site:
<http://www.jvc-victor.co.jp/english/car/>
General settings—PSM
• If you change the “AMP GAIN” setting from
“HIGH POWER” to “LOW POWER” while the
volume level is set higher than “VOLUME 30,” the
unit automatically changes the volume level to
“VOLUME 30.”
Continued on the next page
19
EN14-23_KD-PDR45[U]_7.indd 19
11/20/07 12:23:44 PM
ENGLISH
Preset value setting for each sound mode
Preset value
Sound mode
BASS (bass)
Freq.
Level
MID (mid-range)
Q
Freq.
Level
TRE (treble)
Q
Freq.
Level
LOUD
(loudness)
Q
USER
60 Hz
00
Q1.0 1.0 kHz
00
Q1.25
7.5 kHz
00
Q1.25
ROCK
100 Hz
+03
Q1.0 1.0 kHz
00
Q1.25 10.0 kHz
+02
Q1.25
80 Hz
+01
Q1.0 1.0 kHz
00
Q1.25 10.0 kHz
+03
Q1.25
100 Hz
+02
Q1.0 1.0 kHz
+01
Q1.25 10.0 kHz
+02
Q1.25
HIP HOP
60 Hz
+04
Q1.0 1.0 kHz
–02
Q1.0 10.0 kHz
+01
Q1.25
JAZZ
80 Hz
+03
Q1.0 1.0 kHz
00
Q1.25 10.0 kHz
+03
Q1.25
CLASSIC
POP
OFF
Freq.: Frequency Q: Q-slope
Troubleshooting
What appears to be trouble is not always serious. Check the following points before calling a service center.
FM/AM
General
Symptoms
Remedies/Causes
• Sound cannot be heard from the speakers.
• Adjust the volume to the optimum level.
• Check the cords and connections.
• The unit does not work at all.
Reset the unit (see page 3).
• SSM automatic presetting does not work.
Store stations manually.
• Static noise while listening to the radio.
Connect the antenna firmly.
• Disc cannot be played back.
Insert the disc correctly.
Disc playback
• CD-R/CD-RW cannot be played back.
• Insert a finalized CD-R/CD-RW.
• Tracks on the CD-R/CD-RW cannot be skipped. • Finalize the CD-R/CD-RW with the component which
you used for recording.
• Disc can neither be played back nor ejected.
• Unlock the disc (see page 9).
• Eject the disc forcibly (see page 3).
• Disc sound is sometimes interrupted.
• Stop playback while driving on rough roads.
• Change the disc.
• Check the cords and connections.
• “NO DISC” appears on the display.
• “PLEASE” and “EJECT“ appear alternately on
the display.
Insert a playable disc into the loading slot.
20
EN14-23_KD-PDR45[U]_5.indd 20
11/13/07 12:14:47 PM
MP3/WMA playback
Remedies/Causes
• Disc cannot be played back.
• Use a disc with MP3/WMA tracks recorded in a format
compliant with ISO 9660 Level 1, Level 2, Romeo, or
Joliet.
• Add the extension code <.mp3> or <.wma> to the
file names.
• Noise is generated.
Skip to another track or change the disc. (Do not add the
extension code <.mp3> or <.wma> to non-MP3 or
WMA tracks.)
ENGLISH
Symptoms
• A longer readout time is required (“READING” Do not use too many hierarchical levels and folders.
keeps flashing on the display).
• Tracks do not play back in the order you have The playback order is determined when the files are
intended them to play.
recorded.
• The elapsed playing time is not correct.
This sometimes occurs during playback. This is caused by
how the tracks are recorded on the disc.
iPod playback
• The correct characters are not displayed (e.g. This unit can only display letters (upper case), numbers,
album name).
and a limited number of symbols.
• The iPod does not turn on or does not work.
• Check the connecting cable and its connection.
• Update the firmware version.
• Charge the battery.
• The sound is distorted.
Deactivate the equalizer either on the unit or the iPod.
• “NO IPOD” appears on the display.
• Check the connecting cable and its connection.
• Charge the battery.
• Playback stops.
The headphones are disconnected during playback. Turn
off the unit’s power and turn it on again.
• No sound can be heard when connecting an
iPod nano.
• Disconnect the headphones from the iPod nano.
• Update the firmware version of the iPod nano.
• “NO FILES” appears on the display.
No tracks are stored. Import tracks to the iPod.
• The iPod’s controls do not work after
disconnecting from this unit.
Reset the iPod.
• “CANNOT PLAY” appears on the display.
Communication error occurs.
Disconnect and connect the cable to the iPod again.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
• iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
21
EN14-23_KD-PDR45[U]_5.indd 21
11/13/07 12:14:47 PM
ENGLISH
Specifications
AUDIO AMPLIFIER SECTION
Maximum Power Output:
Front/Rear:
50 W per channel
Continuous Power Output (RMS):
Front/Rear:
19 W per channel into 4 Ω, 40 Hz to 20 000 Hz
at no more than 0.8% total harmonic
distortion.
Load Impedance:
4 Ω (4 Ω to 8 Ω allowance)
Tone Control Range:
Bass:
±12 dB (60 Hz, 80 Hz, 100 Hz, 120 Hz)
Mid-range:
±12 dB (500 Hz, 1 kHz, 1.5 kHz, 2.5 kHz)
Treble:
±12 dB (7.5 kHz, 10 kHz, 12.5 kHz, 15 kHz)
Q (Q-slope):
Q0.5 to Q2.0
Frequency Response:
40 Hz to 20 000 Hz
Signal-to-Noise Ratio:
70 dB
Line-Out Level/Impedance:
2.5 V/20 kΩ load (full scale)
Subwoofer-Out Level/Impedance:
2.5 V/20 kΩ load (full scale)
Output Impedance:
1 kΩ
Other Terminal:
AUX (auxiliary) input jack, iPod connector
TUNER SECTION
Frequency Range:
FM Tuner
AM Tuner
FM:
87.5 MHz to 108.0 MHz
AM:
531 kHz to 1 602 kHz
Usable Sensitivity:
11.3 dBf (1.0 μV/75 Ω)
50 dB Quieting Sensitivity:
16.3 dBf (1.8 μV/75 Ω)
Alternate Channel Selectivity (400 kHz):
65 dB
Frequency Response:
40 Hz to 15 000 Hz
Stereo Separation:
30 dB
Sensitivity:
20 μV
Selectivity:
35 dB
22
EN14-23_KD-PDR45[U]_7.indd 22
11/27/07 9:03:31 AM
Type:
Compact disc player
Signal Detection System:
Non-contact optical pickup
(semiconductor laser)
Number of Channels:
2 channels (stereo)
Frequency Response:
5 Hz to 20 000 Hz
Dynamic Range:
96 dB
Signal-to-Noise Ratio:
98 dB
Wow and Flutter:
Less than measurable limit
ENGLISH
CD PLAYER SECTION
MP3 Decoding Format:
(MPEG1/2 Audio Layer 3)
Max. Bit Rate:
320 kbps
WMA (Windows Media® Audio)
Decoding Format:
Max. Bit Rate:
320 kbps
Operating Voltage:
DC 14.4 V (11 V to 16 V allowance)
GENERAL
Power Requirement:
Grounding System:
Negative ground
Allowable Operating Temperature:
0°C to +40°C
Dimensions (W × H × D): (approx.) Installation Size:
182 mm × 52 mm × 160 mm
Panel Size:
Mass:
188 mm × 58 mm × 6 mm
1.3 kg (excluding accessories)
Design and specifications are subject to change without notice.
23
EN14-23_KD-PDR45[U]_5.indd 23
11/13/07 12:14:49 PM
Having TROUBLE with operation?
Please reset your unit
Refer to page of How to reset your unit
Ada MASALAH dengan cara
pengoperasian?
Setel kembali unit Anda
Lihat halaman mengenai Bagaimana mereset unit anda
EN, IN
© 2007 Victor Company of Japan, Limited
Rear_KD-PDR45[U]_004A.indd 2
1107DTSMDTJEIN
11/28/07 11:04:42 AM
KD-PDR45
Installation/Connection Manual
Manual Pemasangan/Penyambungan
1107DTSMDTJEIN
GET0489-009A
EN, IN
© 2007 Victor Company of Japan, Limited
[UN]
INDONESIA
ENGLISH
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does
not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
Unit ini didisain untuk beroperasi hanya pada 12 V DC, sistem listrik tanah NEGATIVE. Jika kendaraan
anda tidak memiliki sistem ini, sebuah pembalik tegangan diperlukan, yang mana dapat dibeli di penyalurpenyalur audio mobil JVC.
WARNINGS
PERINGATAN
To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all
electrical connections before installing the unit.
• Be sure to ground this unit to the car’s chassis again after installation.
Untuk mencegah hubungan pendek, kami menyarankan anda memutuskan sambungan terminal negatif
baterai dan membuat semua sambungan-sambungan listrik sebelum memasang unit.
• Pastikan untuk mentanahkan unit ini ke casis mobil kembali setelah pemasangan.
Notes:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio
dealer.
• It is recommended to connect speakers with a maximum power of more than 50 W (both at the rear and
at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 50 W, change “AMP
GAIN” setting to prevent the speakers from being damaged (see page 15 of the INSTRUCTIONS).
• To prevent short circuits, cover the terminals of the UNUSED leads with insulating tape.
• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.
Catatan:
• Ganti sekring dengan voltase yang sudah ditetapkan. Jika sekring sering meledak, konsultasikan pada
penyalur audio mobil JVC anda.
• Disarankan untuk menghubungkan speaker-speaker dengan maksimum power lebih dari 50 W (keduanya
di belakang dan di depan, dengan sebuah impedansi 4 Ω sampai 8 Ω). Jika maksimum power kurang
dari 50 W, ganti pengaturan “AMP GAIN” (“PENAMBAH PENGUAT”) untuk mencegah speaker-speaker
dari kerusakan (lihat halaman 15 dari BUKU PETUNJUK).
• Untuk mencegah hubungan pendek, tutup ujung-ujung terminal-terminal TIDAK DIGUNAKAN dengan
pita isolasi.
• Pendingin menjadi sangat panas setelah digunakan. Hati-hati untuk tidak menyentuhnya ketika
memindahkan unit ini.
Heat sink / Pendingin
TINDAKAN-TINDAKAN PENCEGAHAN pada suplai power dan
sambungan-sambungan speaker:
PRECAUTIONS on power supply and speaker connections:
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit
will be seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in
your car.
• JANGAN sambungkan ujung-ujung speaker dari kabel power ke baterai mobil; sebaliknya,
unit tersebut akan secara serius rusak.
• SEBELUM menyambung ujung-ujung speaker dari kabel power ke speaker-speaker, cek perkabelan
speaker dalam mobil anda.
Parts list for installation and connection
Daftar bagian-bagian untuk pemasangan dan penyambungan
The following parts are provided for this unit. If any item is missing, consult your JVC car audio dealer
immediately.
Bagian-bagian berikut disediakan untuk unit ini. Jika ada bagian yang hilang, segera hubungi dealer
audio mobil JVC anda.
A/B
Hard case/Control panel
Kotak keras/Panel kontrol
C
Sleeve
Selongsong
F
Direct connection cable for iPod
Kabel sambungan langsung
untuk iPod
G
Washer (ø5)
Perapat sambungan (ø5)
J
Rubber cushion
Bantalan karet
D
Trim plate
Plat rapi
H
Lock nut (M5)
Mur kunci (M5)
I
Mounting bolt (M4 × 5 mm; M5 × 12.5 mm)
Baut bingkai (M4 × 5 mm; M5 × 12.5 mm)
L
Remote controller
Pengontrol jauh
K
Handles
Pegangan-pegangan
E
Power cord
Kabel power
M
Battery
Baterai
1
Install1_KD-PDR45_009A_6.indd 1
11/20/07 12:30:26 PM
INSTALLATION (IN-DASH MOUNTING)
PEMASANGAN (BINGKAI-DALAM DASH)
The following illustration shows a typical installation. If you have any questions or require information
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Ilustrasi berikut menunjukkan sebuah tipe pemasangan. Jika anda mempunyai suatu pertanyaan atau
informasi yang diperlukan mengenai alat-alat pemasangan, konsultasikan pada penyalur audio mobil JVC
atau sebuah perusahaan yang mensuplai alat-alat.
• Jika anda tidak yakin bagaimana memasang unit ini dengan benar, biarkan dipasang dengan teknisi yang
berkualitas.
Do the required electrical connections.
Lakukan penyambungan-penyambungan
listrik yang diperlukan.
Bend the appropriate tabs to hold the
sleeve firmly in place.
Bengkokkan pengait-pengait yang tepat
untuk menahan selongsong secara kuat
pada tempatnya.
Removing the unit
Memindahkan unit
Before removing the unit, release the rear section.
Sebelum memindahkan unit, lepaskan seksi belakang.
Insert the two handles, then pull them as
illustrated so that the unit can be removed.
Sisipkan kedua pemegang dan tarik pemegang
seperti yang diilustrasikan hingga unit dapat
dipindahkan.
When using the optional stay / Ketika menggunakan
penguat tambahan
Stay (option)
Penguat (tambahan)
When installing the unit without using the sleeve / Ketika memasang unit tanpa
menggunakan selongsong
In a Toyota car for example, first remove the car radio and install the unit in its place.
Dalam sebuah kereta Toyota misalnya, pertama pindahkan radio mobil dan pasang unit tersebut ke dalam tempatnya.
Fire wall
Dinding tahan api
Flat head screws (M5 × 8 mm) *2
Sekrup kepala rata (M5 × 8 mm) *2
Dashboard
Tempat alat pada bagian
depan
Bracket*2
Breket *2
Screw (option)
Sekrup (tambahan)
Flat head screws (M5 × 8 mm) *2
Sekrup kepala rata (M5 × 8 mm) *2
Pocket
Kantong
Bracket *2
Breket *2
Install the unit at an angle of less than 30˚.
Pasang penerima pada suatu sudut
kurang dari 30˚.
Note
Catatan
: When installing the unit on the mounting bracket, make sure to use the 8 mm -long screws. If longer screws are
used, they could damage the unit.
: Ketika memasang unit pada breket bingkai, pastikan untuk menggunakan sekrup-sekrup panjang–8 mm. Jika
sekrup yang lebih panjang digunakan, maka dapat merusak unit.
*1 When you stand the unit, be careful not to damage the fuse on the rear.
*2 Not supplied for this unit.
*1
*2
Ketika anda memberdirikan unit, hati-hati untuk tidak merusak sekring di belakang.
Tidak disediakan untuk unit ini.
2
Install1_KD-PDR45_009A_6.indd 2
11/20/07 12:30:31 PM
ENGLISH
INDONESIA
ELECTRICAL CONNECTIONS
A
SAMBUNGAN-SAMBUNGAN LISTRIK
Typical connections / Ciri khas sambungan-sambungan
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious
damage to this unit.
The leads of the power cord and those of the connector from the car body may be different in color.
Sebelum penyambungan: Cek perkabelan dalam mobil dengan hati-hati. Penyambungan yang tidak
benar mungkin menyebabkan kerusakan serius pada unit.
Ujung dari kabel power dan beberapa konektor dari bodi mobil mungkin berbeda dalam warna.
1
2
3
1
2
3
Connect the colored leads of the power cord in the order specified in the illustration below.
Connect the antenna cord.
Finally connect the wiring harness to the unit.
Line out (see diagram )
Keluaran (lihat diagram )
Sambungkan ujung berwarna dari kabel power dalam urutan spesifikasi pada ilustrasi di bawah.
Sambungkan kabel antena.
Akhirnya sambungkan dudukan kabel ke unit.
Rear ground terminal
Terminal tanah belakang
15 A fuse
Sekring 15 A
Antenna terminal
Terminal antena
iPod connector (see diagram )
Konektor iPod (lihat diagram )
Ignition switch
Saklar kontak
Black
Hitam
To the metallic body or chassis of the car
Ke besi bodi atau casis dari mobil tersebut
Yellow *2
Kuning *2
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
Ke sebuah tempat terminal dalam blok sekring disambungkan ke baterai
mobil (abaikan saklar kontak) (konstant 12 V)
Fuse block
Blok sekring
Red
Merah
To an accessory terminal in the fuse block
Ke sebuah terminal aksesoris dalam blok sekring
Blue
Biru
To the automatic antenna if any (250 mA max.)
Ke antena otomatis jika ada (maksimum 250 mA)
Blue with white stripe
Biru dengan strip putih
White with black stripe
Putih dengan strip hitam
White
Putih
Gray with black stripe
Abu-abu dengan strip hitam
Left speaker (front)
Speaker kiri (depan)
Gray
Abu-abu
To the remote lead of other equipment (200 mA max.)
Ke ujung jauh dari peralatan lain (maksimum 200 mA)
Green with black stripe
Hijau dengan strip hitam
Right speaker (front)
Speaker kanan (depan)
*1 Not supplied for this unit.
*2 Before checking the operation of this unit prior to installation, this lead must be connected, otherwise the
Green
Hijau
Purple with black stripe
Ungu dengan strip hitam
Left speaker (rear)
Speaker kiri (belakang)
Purple
Ungu
Right speaker (rear)
Speaker kanan (belakang)
*1 Tidak disediakan untuk unit ini.
*2 Sebelum pengecekan pengoperasian dari unit ini sebelum pemasangan, ujung ini harus sudah dihubungkan,
power cannot be turned on.
selain itu power tidak dapat dihidupkan.
3
Install2_KD-PDR45_009A_5.indd 3
11/13/07 11:46:22 AM
B
Connecting the external amplifier or subwoofer / Penyambungan penguat eksternal atau subwoofer
Anda dapat menyambungkan penguat untuk meningkatkan sistem stereo mobil anda.
• Sambungkan ujung jauh (biru dengan strip putih) ke ujung jauh dari peralatan lain sehingga dapat
dikontrol melalui unit ini.
• Putuskan sambungan speaker-speaker dari unit ini, sambungkan ini ke penguat. Biarkan
ujung speaker dari unit ini tidak digunakan.
You can connect an amplifier to upgrade your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it
can be controlled through this unit.
• Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker
leads of this unit unused.
Remote lead
Ujung jauh
Y-connector (not supplied for this unit)
Konektor Y (tidak disediakan untuk unit ini)
Remote lead (blue with white stripe)
Ujung jauh (biru dengan strip putih)
Set “L/O MODE” to “REAR” (See page 15 of the
INSTRUCTIONS.)
Setel “L/O MODE ” ke “REAR” (Lihat halaman 15 dari
BUKU PETUNJUK.)
Rear speakers
Speaker-speaker
belakang
To the remote lead of other equipment or automatic
antenna if any
Ke ujung jauh dari peralatan lain atau antena
otomatis jika ada
JVC Amplifier
Penguat JVC
Signal cord (not supplied for this unit)
Kabel sinyal (tidak disediakan untuk unit ini)
Set “L/O MODE” to “SUB.W” (See page 15 of the
INSTRUCTIONS.)
Setel “L/O MODE ” ke “SUB.W” (Lihat halaman 15 dari
BUKU PETUNJUK.)
Subwoofer
Subwoofer
C
JVC Amplifier
Penguat JVC
Front speakers
Speaker-speaker depan
or
atau
Connecting an Apple iPod / Menghubungkan Apple iPod
You can connect an iPod to this unit using the supplied direct connection cable for iPod.
Anda dapat menghubungkan iPod ke unit ini dengan menggunakan kabel sambungan langsung yang
disediakan untuk iPod.
Apple iPod (separately purchased)
Apple iPod (dibeli terpisah)
iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
iPod adalah merek dagang dari Apple Inc., terdaftar di
Amerika Serikat dan di negara-negara lain.
Direct connection cable for iPod (supplied)
Kabel sambungan langsung untuk iPod (disediakan)
*3 Pasangkan dengan kuat kabel tanah ke bodi besi atau ke casis dari mobil—pada tempat yang tidak dilapisi cat
*3 Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint
(jika dilapisi cat, hilangkan cat sebelum memasang kabel). Kegagalan melakukan ini mungkin menyebabkan
kerusakan pada unit tersebut.
(if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the
unit.
PEMECAHAN MASALAH
TROUBLESHOOTING
• The fuse blows.
* Are the red and black leads connected correctly?
• Sekring meledak.
* Apakah ujung-ujung merah dan hitam tersambung dengan benar?
• Power cannot be turned on.
* Is the yellow lead connected?
• Power tidak dapat dihidupkan.
* Apakah ujung kuning sudah tersambung?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• Tidak ada suara dari speaker.
* Apakah ujung keluaran speaker terhubung pendek?
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• Suara terdistorsi.
* Apakah ujung keluaran speaker sudah ditanahkan?
* Apakah terminal-terminal “–” dari speaker-speaker L dan R sudah ditanahkan secara umum?
• Noise interfere with sounds.
* Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?
• Berisik yang mengganggu suara-suara.
* Apakah terminal tanahan belakang tersambung ke casis mobil menggunakan kabel-kabel terpendek dan
tertebal?
• This unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• Unit menjadi panas.
* Apakah ujung keluaran speaker sudah ditanahkan?
* Apakah terminal-terminal “–” dari speaker-speaker L dan R sudah ditanahkan secara umum?
• This unit does not work at all.
* Have you reset your unit?
• Unit ini tidak bekerja secara keseluruhan.
* Apakah anda sudah reset (memasang kembali) unit anda?
4
Install2_KD-PDR45_009A_4.indd 4
11/2/07 9:42:29 AM
KD-PDR45
ENGLISH
CD RECEIVER
KD-PDR45
For canceling the display demonstration, see page 6.
For installation and connections, refer to the separate manual.
INSTRUCTIONS
GET0489-005A
[UT]
Cover_KD-PDR45[U]_1.indd 1
7/24/07 10:35:05 AM
ENGLISH
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best
possible performance from the unit.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to
qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical
instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
Detaching the control panel
[European Union only]
Warning:
If you need to operate the unit while driving, be
sure to look around carefully or you may be involved
in a traffic accident.
Attaching the control panel
2
EN02-05_KD-PDR45[U]_5.indd 2
11/2/07 8:56:33 AM
CONTENTS
Control panel .................................. 4
Remote controller — RM-RK50........... 5
Getting started ................................ 6
ENGLISH
How to reset your unit
Basic operations ................................................... 6
• Your preset adjustments will also be erased.
Radio operations ............................. 7
Disc operations ................................ 8
Playing a disc in the unit ..................................... 8
How to forcibly eject a disc
• Be careful not to drop the disc when it ejects.
• If this does not work, reset your unit.
How to use the M MODE button
If you press M MODE, the unit goes into functions mode,
then the number buttons and 5/∞ buttons work as
different function buttons.
Ex.: When number button 2 works as
MO (monaural) button.
iPod operations ...............................
Sound adjustments ..........................
General settings — PSM ..................
Other external component
operations ...................................
Title assignment..............................
Maintenance ...................................
More about this unit ........................
Troubleshooting ..............................
Specifications ..................................
10
12
14
16
16
17
17
20
22
For safety...
• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
• Stop the car before performing any complicated
operations.
Temperature inside the car...
To use these buttons for their original functions
again after pressing M MODE, press M MODE again.
• Waiting for about 5 seconds without pressing any of
these buttons will automatically cancels the functions
mode.
If you have parked the car for a long time in hot or cold
weather, wait until the temperature in the car becomes
normal before operating the unit.
3
EN02-05_KD-PDR45[U]_5.indd 3
11/2/07 8:56:34 AM
ENGLISH
Control panel
Parts identification
Display window
1
2
3
4
5
6
7
8
9
p
q
w
e
r
t
y
u
i
5 (up) / ∞ (down) buttons
0 (eject) button
(standby/on attenuator) button
Control dial
Remote sensor
DO NOT expose the remote sensor to strong light
(direct sunlight or artificial lighting).
BAND button
Loading slot
Display window
EQ (equalizer) button
DISP (display) button
(control panel release) button
i (iPod) button
4 /¢ buttons
SRC (source) button
SEL (select) button
M MODE button
MO (monaural) button
SSM (Strong-station Sequential Memory) button
o
;
a
s
d
f
g
h
j
k
l
/
z
x
Number buttons
RPT (repeat) button
RND (random) button
AUX (auxiliary) input jack
Source display / Track number / Folder number /
Time countdown indicator
Tr (track) indicator
DISC indicator
Playback mode / item indicators— RND (random),
(disc), (folder), RPT (repeat)
Tuner reception indicators—ST (stereo),
MO (monaural)
Sound mode (iEQ: intelligent equalizer) indicators
—CLASSIC, HIP HOP, JAZZ, ROCK, POPS, USER
LOUD (loudness) indicator
EQ (equalizer) indicator
Disc information indicators—
TAG (Tag information), (folder), (track/file)
Main display
4
EN02-05_KD-PDR45[U]_5.indd 4
11/2/07 8:56:35 AM
Remote controller — RM-RK50
ENGLISH
Main elements and features
Installing the lithium coin battery
(CR2025)
1
2
Aim the remote controller directly at the remote
sensor on the unit. Make sure there is no obstacle
in between.
Warning:
• Do not install any battery other than CR2025 or its
equivalent; otherwise, it may explode.
• Do not leave the remote controller in a place
(such as the dashboard) exposed to direct
sunlight for a long time; otherwise, it may
explode.
• Store the battery in a place where children cannot
reach to avoid the risk of accidents.
• To prevent the battery from over-heating,
cracking, or starting a fire:
– Do not recharge, short, disassemble, heat the
battery, or dispose of it in a fire.
– Do not leave the battery with other metallic
materials.
– Do not poke the battery with tweezers or
similar tools.
– Wrap the battery with tape and insulate when
throwing away or saving it.
3
4
5
6
(standby/on/attenuator) button
• Turns the power on if pressed briefly or
attenuates the sound when the power is on.
• Turns the power off if pressed and held.
5 U (up) / D (down) ∞ buttons
• Changes the FM/AM bands with 5 U.
• Changes the preset stations with D ∞.
• Changes the folder of the MP3/WMA discs.
• While listening to an Apple iPod.
– Enters the main menu if pressed and held.
(Now 5 U/D ∞/2 R/F 3 work as the menu
selecting buttons.)
• While listening to an iPod (in menu selecting
mode):
– Selects an item if pressed D ∞ briefly. (Then,
press and hold D ∞ to play back the selection
directly.)
– Returns to the previous menu if pressed 5 U
briefly.
VOL – / VOL + buttons
• Adjusts the volume level.
SOUND button
• Selects the sound mode (iEQ: intelligent
equalizer).
SOURCE button
• Selects the source.
2 R (reverse) / F (forward) 3 buttons
• Searches for stations if pressed briefly.
• Fast-forwards or reverses the track if pressed and
held.
• Changes the track if pressed briefly.
• While listening to an iPod (in menu selecting
mode):
– Accelerated file search: Hold 2 R/F 3 to fast
skip during song search in the main menu.
5
EN02-05_KD-PDR45[U]_7.indd 5
11/20/07 12:16:46 PM
ENGLISH
Getting started
Basic operations
~
Turn on the power.
To drop the volume in a
moment (ATT)
To restore the sound, press
the button again.
To turn off the power
Ÿ
Basic settings
• See also “General settings — PSM” on pages
14 and 15.
1
*1 You cannot select “CD” as the playback source
if there is no disc in the unit.
*2 “NO IPOD” appears if an iPod is not connected.
!
2
For FM/AM tuner
1 Canceling the display demonstrations
Select “DEMO,” then “DEMO OFF.”
2 Setting the clock
⁄
Select “CLOCK HOUR,” then adjust the hour.
Select “CLOCK MIN” (minute), then adjust the
minute.
Adjust the volume.
3
Volume level appears.
@
Adjust the sound as you want. (See
pages 12 and 13.)
Finish the procedure.
To check the current clock time while the
power is turned off
Clock time is shown on the display for
about 5 seconds. See also page 14.
Caution on volume setting:
Discs produce very little noise compared with other
sources. Lower the volume before playing a disc
to avoid damaging the speakers by the sudden
increase of the output level.
6
EN06-13_KD-PDR45[U]_5.indd 6
11/2/07 8:56:47 AM
When an FM stereo broadcast is hard to
receive
~
Lights up when monaural mode is activated.
Ÿ
Reception improves, but the stereo effect will be lost.
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
!
ENGLISH
Radio operations
To restore the stereo effect, repeat the same
procedure. “MONO OFF” appears and the MO indicator
goes off.
Storing stations in memory
Start searching for a station.
You can preset six stations for each band.
When a station is received, searching stops.
To stop searching, press the same button
again.
FM station automatic presetting—
SSM (Strong-station Sequential
Memory)
1
Select the FM band (FM1 – FM3) you want to
store into.
To tune in to a station manually
In step ! above...
1
2
3
2 Select a desired station frequency.
“SSM” flashes, then disappears when automatic
presetting is over.
Local FM stations with the strongest signals are
searched and stored automatically in the FM band.
7
EN06-13_KD-PDR45[U]_5.indd 7
11/2/07 8:56:48 AM
ENGLISH
Manual presetting
Ex.: Storing the FM station of 92.50 MHz into preset
number 4 of the FM1 band.
1
Disc operations
Playing a disc in the unit
All tracks will be played repeatedly until you change the
source or eject the disc.
2
3
To stop play and eject the disc
Preset number flashes for a while.
Listening to a preset station
1
2
• Press SRC to listen to another
playback source.
[Hold] To fast-forward or reverse the
track
Select the preset station (1 – 6) you want.
[Press] To go to the next or previous
track
or
[Press] To go to the next or previous
folder (only for MP3 or WMA
discs)
To locate a particular track (for CD) or folder
(for MP3 or WMA discs) directly
To check other information while listening
to the radio
Frequency = Clock =
Station name * = (back to the
beginning)
To select a number from 01 – 06:
To select a number from 07 – 12:
* If no title is assigned to a station, “NO NAME” appears.
To assign a title to a station, see page 16.
8
EN06-13_KD-PDR45[U]_5.indd 8
11/2/07 8:56:49 AM
To select a particular track in a folder
(for MP3 or WMA discs):
Changing the display information
While playing an audio CD or CD Text
ENGLISH
• To use direct folder access on MP3/WMA discs, it
is required that folders are assigned with 2-digit
numbers at the beginning of their folder names—
01, 02, 03, and so on.
A = B = Disc title/performer *1 = Track
title *1 [ ] = (back to the beginning)
Other main functions
Skipping tracks quickly during play
• For MP3 or WMA discs, you can skip tracks within the
same folder.
Ex.: To select track 32 while playing a track whose
number is a single digit (1 to 9)
While playing an MP3 or a WMA track
• When “TAG DISPLAY” is set to “TAG ON”
(see page 15)
A = B = Album name/performer (folder
name *2) [
] = Track title (file
name *2) [
] = (back to the beginning)
• When “TAG DISPLAY” is set to “TAG OFF”
1
A = B = Folder name [ ] = File name
[ ] = (back to the beginning)
2
Each time you press the button, you can skip 10
tracks.
• After the last track, the first track will be selected
and vice versa.
3
A : Current track number with the elapsed playing
time
B : Current track number with the clock time
[ ] : Corresponding indicator lights up on the display.
*1 If the current disc is an audio CD, “NO NAME” appears.
*2 If an MP3/WMA file does not have Tag information,
folder name and file name appear. In this case, the
TAG indicator will not light up.
Prohibiting disc ejection
You can lock a disc in the loading slot.
“EJECT LOCK” flashes on the display.
To cancel the prohibition, repeat the same
procedure.
9
EN06-13_KD-PDR45[U]_5.indd 9
11/2/07 8:56:49 AM
ENGLISH
Selecting the playback modes
You can use only one of the following playback modes
at a time.
1
2
Select your desired playback mode.
iPod operations
You can play songs in an Apple iPod by connecting it
with the supplied direct connection cable for iPod.
You can control playback from the unit or from your
iPod.
• Disconnecting the iPod will stop playback. Press SRC
to listen to another playback source.
Caution:
7 Repeat play
Mode
Plays repeatedly
]
TRACK RPT : The current track. [
FOLDER RPT * : All tracks of the current folder.
[
]
RPT OFF
: Cancels.
7 Random play
Mode
Plays at random
• Avoid using the iPod if it might hinder your safety
while driving.
• Make sure all important data has been backed up
to avoid losing the data.
• For connection, see the Installation/Connection
Manual (separate volume).
• For details, refer also to the manual supplied for your
iPod.
~
Connect an iPod.
Direct connection
cable for iPod
FOLDER RND *: All tracks of the current folder,
then the tracks of the next folder
and so on. [
]
ALL RND
: All tracks of the current disc.
[
]
RND OFF
: Cancels.
* Only while playing an MP3 or a WMA disc.
If an iPod has been connected...
To directly select “IPOD” as the source
while listening to another source or
when the power is turned off.
[ ] : Corresponding indicator lights up on the
display.
Playback starts automatically from where it had
been paused previously.
Ÿ
Adjust the volume.
10
EN06-13_KD-PDR45[U]_5.indd 10
11/2/07 8:56:50 AM
Adjust the sound as you want. (See
pages 12 and 13.)
Selecting a track from the menu
1
ENGLISH
!
Enter the main menu.
To control playback from your iPod
or
“IPOD MODE” appears on the
display.
Now the 5/∞/4 /¢ /number
buttons work as the menu selecting buttons.
• Press and hold this button again to control playback
from the unit. “HEAD MODE” appears on the display.
2
Select the desired menu.
Playback control from the unit
[Press] Go to the next or previous
track
[Hold] Fast-forward or reverse the
track during playback
Fast-skip the menu items of
the main menu
PLAYLIST Ô ARTIST Ô ALBUM Ô SONG
Ô PODCASTÔ GENRE Ô COMPOSER Ô
AUDIOBOOK Ô (back to the beginning)
[Hold] Enter the main menu (see the
right column).
[Press] Pause/resume playback.
• Pressing the number buttons can directly select
the desired menu (see the left column for
details).
3
Confirm the selection.
To move back to the previous
menu, press 5.
[Press] Go to the top menu of “PLAYLIST,” “ARTIST,”
“ALBUM,” “SONG,” “PODCAST,” or “GENRE” in
the main menu (see the right column).
[Hold] Go to the top menu of “COMPOSER” or
“AUDIOBOOK” in the main menu (see the
right column).
• Holding the button will start play back the
selected item directly.
• If a track is selected, playback starts
automatically.
• If the selected item has another layer, you will
enter the layer. Repeat steps 2 and 3 until the
desired track is played.
• Accelerated file search: Hold 4 /¢
to fast skip during song search in the main
menu.
Continued on the next page
11
EN06-13_KD-PDR45[U]_7.indd 11
11/20/07 12:49:50 PM
ENGLISH
To exit from menu selecting mode
To check other information while listening
to an iPod
or
* The menu selecting mode will be canceled:
– If no operations are performed for about
10 seconds.
– When you confirm the selection of a track.
– Pressing some other buttons such as DISP, SEL,
MODE, or EQ.
Current track number with the elapsed
playing time = Current track number with
the clock time = Track title * = Album name/
performer * = (back to the beginning)
* When “TAG DISPLAY” is set to “TAG OFF,” file name and
folder name appear.
Selecting the playback modes
1
2
Sound adjustments
You can select a preset sound mode suitable to the
music genre (iEQ: intelligent equalizer).
Select your desired playback mode.
7 Repeat play
Mode
ONE RPT
ALL RPT
RPT OFF
Playback functions (as on iPod)
: Same as “Repeat One.” [
: Same as “Repeat All.” [
: Cancels.
Adjusting the sound
]
]
You can adjust the sound characteristics to your
preference.
• The adjustment you make will be stored for the
currently selected sound mode (iEQ) including
“USER.”
7 Random play
Mode
Playback functions (as on iPod)
SONG RND : Same as “Shuffle Songs.” [
ALBUM RND * : Same as “Shuffle Albums.”
[
]
RND OFF
: Cancels.
]
1
2
* Functions only if you select “ALL” in “ALBUMS” of
the main menu
[ ] : Corresponding indicator lights up on the
display.
Indication, [Range]
FADER *2, [R06 to F06]
Adjust the front and rear speaker balance.
BALANCE *3, [L06 to R06]
Adjust the left and right speaker balance.
12
EN06-13_KD-PDR45[U]_7.indd 12
11/20/07 12:23:25 PM
3
Select a sound characteristic.
4
Adjust the sound elements of the selected
sound characteristic.
1 Adjust the frequency.
LOUD *4 (loudness), [LOUD ON or LOUD OFF]
Boost low and high frequencies to produce a
well-balanced sound at a low volume level.
SUBWOOFER *1, [00 to 08, initial: 04]
Adjust the subwoofer output level.
VOL ADJ (volume adjust), [–05 to +05, initial: 00]
Adjust the volume level of each source (except FM), in
relation to the FM volume level. The volume level will
automatically increase or decrease when you change
the source.
• Before making an adjustment, select the source you
want to adjust.
ENGLISH
Indication, [Range]
2 Adjust the level.
VOLUME, [00 to 50 or 00 to 30 ]*5
Adjust the volume.
*1 Displayed only when “L/O MODE” is set to “SUB.W”
(see page 15).
*2 If you are using a two-speaker system, set the fader
level to “00.”
*3 This adjustment will not affect the subwoofer output.
*4 The adjustment made (LOUD ON/LOUD OFF) will be
applied to all sound modes.
*5 Depending on the amplifier gain control setting. (See
page 15 for details.)
3 Adjust the quality slope (Q).
Sound
elements
BASS
MID
TRE
Frequency
60 Hz
80 Hz
100 Hz
120 Hz
500 Hz
1.0 kHz
1.5 kHz
2.5 kHz
7.5 kHz
10.0 kHz
12.5 kHz
15.0 kHz
Level
–06 to
+06
–06 to
+06
–06 to
+06
Q (Q-slope)
Q0.5
Q1.0
Q1.5
Q2.0
Q0.75
Q1.0
Q1.25
Q1.5
Q0.75
Q1.25
Storing your own sound mode
You can adjust the sound modes and store your own
adjustments in memory.
1
2
Range/selectable items
Select a sound mode.
Enter the adjustment mode.
• If no operation is done within
5 seconds, this mode is canceled.
BASS: Bass MID: Mid-range TRE: Treble
5
The adjustment made will be stored
automatically. Repeat steps 3 and 4 to adjust
other sound characteristics.
13
EN06-13_KD-PDR45[U]_7.indd 13
11/20/07 12:23:26 PM
ENGLISH
General settings — PSM
You can change PSM (Preferred Setting Mode) items
listed in the table below and on page 15.
3
Adjust the PSM item selected.
4
Repeat steps 2 and 3 to adjust other PSM
items if necessary.
5
Finish the procedure.
1
2
Select a PSM item.
Indications
Item
( : Initial)
Setting, [reference page]
DEMO
Display
demonstration
• DEMO ON
: The display demonstration will be activated automatically if no
operation is done for about 20 seconds, [6].
: Cancels.
CLOCK DISP *1
Clock display
• CLOCK ON
• DEMO OFF
• CLOCK OFF
: The clock time is shown on the display at all times when the power is
turned off.
: Cancels; pressing DISP will show the clock time for about 5 seconds
when the power is turned off, [6].
CLOCK HOUR
Hour adjustment
1 – 12
[Initial: 1 (1:00)], [6].
CLOCK MIN
Minute adjustment
00 – 59
[Initial: 00 (1:00)], [6].
DIMMER
Dimmer
• ON
• OFF
: Dims the display and button illumination.
: Cancels.
*1 If the power supply is not interrupted by turning off the ignition key of your car, it is recommended that you select
“CLOCK OFF” to save the car’s battery.
14
EN14-23_KD-PDR45[U]_5.indd 14
11/2/07 8:57:02 AM
Item
( : Initial)
Setting, [reference page]
AUDIOBOOKS *2
Speed control of
“Audiobook”
• NORMAL
• FASTER
• SLOWER
: You can select the playback speed of the “Audiobook” sound file in
your iPod.
SCROLL *3
Scroll
• ONCE
• AUTO
• OFF
:
:
:
•
L/O MODE
Line output mode
• REAR
: Select if the REAR LINE OUT terminals are used for connecting the
speakers (through an external amplifier).
: Select if the REAR LINE OUT terminals are used for connecting a
subwoofer (through an external amplifier).
• SUB.W
ENGLISH
Indications
Scrolls the displayed information once.
Repeats scrolling (at 5-second intervals).
Cancels.
Pressing DISP for more than one second can scroll the display
regardless of the setting.
SUB.W FREQ *4
Subwoofer cutoff
frequency
• LOW
• MID
• HIGH
: Frequencies lower than 90 Hz are sent to the subwoofer.
: Frequencies lower than 135 Hz are sent to the subwoofer.
: Frequencies lower than 180 Hz are sent to the subwoofer.
TAG DISPLAY
Tag display
• TAG ON
• TAG OFF
: Shows the Tag information while playing MP3/WMA tracks, [9].
: Cancels.
AMP GAIN
Amplifier gain
control
• LOW POWER
IF BAND
Intermediate
frequency band
• AUTO
: VOLUME 00 – VOLUME 30. (Select this if the maximum power of the
speaker is less than 50 W to avoid damaging the speaker.)
• HIGH POWER : VOLUME 00 – VOLUME 50.
• WIDE
: Increases the tuner selectivity to reduce interference noise between
close stations. (The stereo effect may be lost.)
: Subject to interference noise from adjacent stations, but the sound
quality will not be degraded and the stereo effect will remain.
*2 Displayed only when an iPod is connected and playback is controlled from the unit.
*3 Some characters or symbols will not be shown correctly (or will be blanked) on the display.
*4 Displayed only when “L/O MODE” is set to “SUB.W.”
15
EN14-23_KD-PDR45[U]_5.indd 15
11/2/07 8:57:04 AM
ENGLISH
Other external component
operations
You can connect an external component to the AUX
(auxiliary) input jack on the control panel.
Title assignment
You can assign names to 30 station frequencies (FM and
AM) and up to 8 characters for each station name.
1
Select FM/AM.
2
Show the title entry screen.
3
Assign a title.
1 Select a character.
Portable audio player, etc.
3.5 mm stereo mini
plug (not supplied)
~
Ÿ
!
Turn on the connected component and
start playing the source.
Adjust the volume.
2 Move to the next (or previous) character
position.
⁄
3 Repeat steps 1 and 2 until you finish
Adjust the sound as you want. (See
pages 12 and 13.)
entering the title.
4
Finish the procedure.
To check other information while listening
to an external component
Clock Ô AUX IN
To erase the entire title
In step 2 above...
16
EN14-23_KD-PDR45[U]_5.indd 16
11/2/07 8:57:05 AM
How to clean the connectors
Frequent detachment will deteriorate the connectors.
To minimize this possibility, periodically wipe the
connectors with a cotton swab or cloth moistened with
alcohol, being careful not to damage the connectors.
To play new discs
New discs may have some rough spots
around the inner and outer edges. If
such a disc is used, this unit may reject
the disc.
To remove these rough spots, rub the edges with a
pencil or ball-point pen, etc.
ENGLISH
Maintenance
Do not use the following discs:
Connectors
Single CD (8 cm disc)
Warped disc
Sticker and
sticker residue
Stick-on label
Moisture condensation
Moisture may condense on the lens inside the unit in
the following cases:
• After starting the heater in the car.
• If it becomes very humid inside the car.
Should this occur, the unit may malfunction. In this
case, eject the disc and leave the unit turned on for a
few hours until the moisture has evaporated.
How to handle discs
When removing a disc from its case, press down the
center holder of the case and lift the Center holder
disc out, holding it by the edges.
• Always hold the disc by the edges.
Do not touch its recording surface.
When storing a disc in its case, gently insert the
disc around the center holder (with the printed surface
facing up).
• Make sure to store discs in cases after use
To keep discs clean
A dirty disc may not play correctly.
If a disc does become dirty, wipe it with
a soft cloth in a straight line from center
to edge.
• Do not use any solvents (for example, conventional
record cleaner, spray, thinner, benzine, etc.) to clean
discs..
Unusual shape
More about this unit
Basic operations
Turning on the power
• By pressing SRC (source) or i (iPod) button on the
unit, you can also turn on the power. If the source is
ready, playback also starts.
Turning off the power
• If you turn off the power while listening to a track,
playback will start from where it had been stopped
previously next time you turn on the power.
General
• If you change the source while listening to a disc or
an iPod, playback stops.
Next time you select “CD” or “IPOD” as the playback
source, playback will start from where it had been
stopped/paused previously.
Continued on the next page
17
EN14-23_KD-PDR45[U]_5.indd 17
11/13/07 12:14:43 PM
ENGLISH
• After ejecting a disc or disconnecting an iPod,
“NO DISC” or “NO IPOD” appears and you cannot
operate some of the buttons. Insert another disc,
connect an iPod, or press SRC to select another
playback source.
Tuner operations
Storing stations in memory
• During SSM search...
– All previously stored stations are erased and the
stations are stored anew.
– Received stations are preset in No. 1 (lowest
frequency) to No. 6 (highest frequency).
– When SSM is over, the station stored in No. 1 will
be automatically tuned in.
• When storing a station manually, the previously
preset station is erased when a new station is stored
in the same preset number.
Disc operations
Caution for DualDisc playback
• The Non-DVD side of a “DualDisc” does not comply
with the “Compact Disc Digital Audio” standard.
Therefore, the use of Non-DVD side of a DualDisc on
this product may not be recommended.
General
• This unit has been designed to reproduce
CDs/CD Texts, and CD-Rs (Recordable)/CD-RWs
(Rewritable) in audio CD (CD-DA), MP3 and WMA
formats.
• When a disc is inserted upside down, “PLEASE” and
“EJECT” appear alternately on the display. Press 0 to
eject the disc.
• MP3 and WMA “tracks” (words “file” and “track” are
used interchangeably) are recorded in “folders.”
• While fast-forwarding or reversing on an MP3 or
WMA disc, you can only hear intermittent sounds.
Playing a CD-R or CD-RW
• Use only “finalized” CD-Rs or CD-RWs.
• This unit can only play back files of the same type as
those which are detected first if a disc includes both
audio CD (CD-DA) files and MP3/WMA files.
• This unit can play back multi-session discs; however,
unclosed sessions will be skipped while playing.
• Some CD-Rs or CD-RWs may not play back on this
unit because of their disc characteristics, or for the
following reasons:
– Discs are dirty or scratched.
– Moisture condensation has occurred on the lens
inside the unit.
– The pickup lens inside the unit is dirty.
– The files on the CD-R/CD-RW are written using the
“Packet Write” method.
– There are improper recording conditions (missing
data, etc.) or media conditions (stained, scratched,
warped, etc.).
• CD-RWs may require a longer readout time since the
reflectance of CD-RWs is lower than that of regular
CDs.
• Do not use the following CD-Rs or CD-RWs:
– Discs with stickers, labels, or a protective seal stuck
to the surface.
– Discs on which labels can be directly printed by an
ink jet printer.
Using these discs under high temperature or high
humidity may cause malfunctions or damage to the
unit.
Playing an MP3/WMA disc
• This unit can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of
the letter case—upper/lower).
• This unit can show the names of albums, artists
(performer), and Tag (Version 1.0, 1.1, 2.2, 2.3, or
2.4) for MP3 files and for WMA files.
• This unit can display only one-byte characters. No
other characters can be correctly displayed.
• This unit can play back MP3/WMA files meeting the
conditions below:
– Bit rate: 8 kbps — 320 kbps
18
EN14-23_KD-PDR45[U]_6.indd 18
11/14/07 4:35:31 PM
•
•
•
•
Ejecting a disc
• If the ejected disc is not removed within 15 seconds,
it is automatically inserted into the loading slot again
to protect it from dust. Playback starts automatically.
iPod operations
• Controllable iPod:
– iPod mini
– iPod G4
•
•
•
•
•
•
•
•
•
– iPod photo
– iPod nano (1st & 2nd Generation)
– iPod with video (5th Generation)
Update your iPod to the latest software version
before using it with this unit.
When you turn on this unit, the iPod is charged
through this unit.
While connecting an iPod with Video:
– No video shows on the iPod’s display or the
external monitor (only the audio part is available).
– It is not possible to browse video files on the
“Video“ menu. (If you connect the iPod during
the playback or pausing of a video file, resuming
playback will not work.)
iPod shuffle cannot be used with this unit.
You can control the iPod from this unit when “JVC” or
“ ” appears on the iPod display after connection.
The song order displayed on the selection menu of
this unit may differ from that of the iPod.
If playback is stopped, select a track from the
selection menu or press BAND to playback the same
track again.
The text information may not be displayed correctly:
– Some characters such as accented letters cannot be
shown correctly on the display.
– Communication between the iPod and the unit is
not stable.
If the text information includes more than
11 characters, it scrolls on the display. This unit can
display up to 64 characters.
ENGLISH
•
– Sampling frequency:
48 kHz, 44.1 kHz, 32 kHz (for MPEG-1)
24 kHz, 22.05 kHz, 16 kHz (for MPEG-2)
– Disc format: ISO 9660 Level 1/Level 2, Romeo,
Joliet, Windows long file name
The maximum number of characters for file/folder
names vary depending on the disc format used
(includes 4 extension characters—<.mp3> or
<.wma>).
– ISO 9660 Level 1: up to 12 characters
– ISO 9660 Level 2: up to 31 characters
– Romeo: up to 128 characters
– Joliet: up to 64 characters
– Windows long file name: up to 128 characters
This unit can recognize a total of 512 files,
255 folders, and 8 hierarchical levels.
This unit can play back files recorded in VBR (variable
bit rate).
Files recorded in VBR have a discrepancy in the
elapsed time display, and do not show the actual
elapsed time. In particular, this difference becomes
noticeable after performing the search function.
This unit cannot play back the following files:
– MP3 files encoded in MP3i and MP3 PRO format.
– MP3 files encoded in an inappropriate format.
– MP3 files encoded with Layer 1/2.
– WMA files encoded in lossless, professional, and
voice format.
– WMA files which are not based upon Windows
Media® Audio.
– WMA files copy-protected with DRM.
– Files which have data such as AIFF, ATRAC3, etc.
The search function works but search speed is not
constant.
Notice:
When operating an iPod, some operations may not
be performed correctly or as intended. In this case,
visit the following JVC web site:
<http://www.jvc-victor.co.jp/english/car/>
General settings—PSM
• If you change the “AMP GAIN” setting from
“HIGH POWER” to “LOW POWER” while the
volume level is set higher than “VOLUME 30,” the
unit automatically changes the volume level to
“VOLUME 30.”
Continued on the next page
19
EN14-23_KD-PDR45[U]_7.indd 19
11/20/07 12:23:44 PM
ENGLISH
Preset value setting for each sound mode
Preset value
Sound mode
BASS (bass)
Freq.
Level
MID (mid-range)
Q
Freq.
Level
TRE (treble)
Q
Freq.
Level
LOUD
(loudness)
Q
USER
60 Hz
00
Q1.0 1.0 kHz
00
Q1.25
7.5 kHz
00
Q1.25
ROCK
100 Hz
+03
Q1.0 1.0 kHz
00
Q1.25 10.0 kHz
+02
Q1.25
80 Hz
+01
Q1.0 1.0 kHz
00
Q1.25 10.0 kHz
+03
Q1.25
100 Hz
+02
Q1.0 1.0 kHz
+01
Q1.25 10.0 kHz
+02
Q1.25
HIP HOP
60 Hz
+04
Q1.0 1.0 kHz
–02
Q1.0 10.0 kHz
+01
Q1.25
JAZZ
80 Hz
+03
Q1.0 1.0 kHz
00
Q1.25 10.0 kHz
+03
Q1.25
CLASSIC
POP
OFF
Freq.: Frequency Q: Q-slope
Troubleshooting
What appears to be trouble is not always serious. Check the following points before calling a service center.
FM/AM
General
Symptoms
Remedies/Causes
• Sound cannot be heard from the speakers.
• Adjust the volume to the optimum level.
• Check the cords and connections.
• The unit does not work at all.
Reset the unit (see page 3).
• SSM automatic presetting does not work.
Store stations manually.
• Static noise while listening to the radio.
Connect the antenna firmly.
• Disc cannot be played back.
Insert the disc correctly.
Disc playback
• CD-R/CD-RW cannot be played back.
• Insert a finalized CD-R/CD-RW.
• Tracks on the CD-R/CD-RW cannot be skipped. • Finalize the CD-R/CD-RW with the component which
you used for recording.
• Disc can neither be played back nor ejected.
• Unlock the disc (see page 9).
• Eject the disc forcibly (see page 3).
• Disc sound is sometimes interrupted.
• Stop playback while driving on rough roads.
• Change the disc.
• Check the cords and connections.
• “NO DISC” appears on the display.
• “PLEASE” and “EJECT“ appear alternately on
the display.
Insert a playable disc into the loading slot.
20
EN14-23_KD-PDR45[U]_5.indd 20
11/13/07 12:14:47 PM
MP3/WMA playback
Remedies/Causes
• Disc cannot be played back.
• Use a disc with MP3/WMA tracks recorded in a format
compliant with ISO 9660 Level 1, Level 2, Romeo, or
Joliet.
• Add the extension code <.mp3> or <.wma> to the
file names.
• Noise is generated.
Skip to another track or change the disc. (Do not add the
extension code <.mp3> or <.wma> to non-MP3 or
WMA tracks.)
ENGLISH
Symptoms
• A longer readout time is required (“READING” Do not use too many hierarchical levels and folders.
keeps flashing on the display).
• Tracks do not play back in the order you have The playback order is determined when the files are
intended them to play.
recorded.
• The elapsed playing time is not correct.
This sometimes occurs during playback. This is caused by
how the tracks are recorded on the disc.
iPod playback
• The correct characters are not displayed (e.g. This unit can only display letters (upper case), numbers,
album name).
and a limited number of symbols.
• The iPod does not turn on or does not work.
• Check the connecting cable and its connection.
• Update the firmware version.
• Charge the battery.
• The sound is distorted.
Deactivate the equalizer either on the unit or the iPod.
• “NO IPOD” appears on the display.
• Check the connecting cable and its connection.
• Charge the battery.
• Playback stops.
The headphones are disconnected during playback. Turn
off the unit’s power and turn it on again.
• No sound can be heard when connecting an
iPod nano.
• Disconnect the headphones from the iPod nano.
• Update the firmware version of the iPod nano.
• “NO FILES” appears on the display.
No tracks are stored. Import tracks to the iPod.
• The iPod’s controls do not work after
disconnecting from this unit.
Reset the iPod.
• “CANNOT PLAY” appears on the display.
Communication error occurs.
Disconnect and connect the cable to the iPod again.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
• iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
21
EN14-23_KD-PDR45[U]_5.indd 21
11/13/07 12:14:47 PM
ENGLISH
Specifications
AUDIO AMPLIFIER SECTION
Maximum Power Output:
Front/Rear:
50 W per channel
Continuous Power Output (RMS):
Front/Rear:
19 W per channel into 4 Ω, 40 Hz to 20 000 Hz
at no more than 0.8% total harmonic
distortion.
Load Impedance:
4 Ω (4 Ω to 8 Ω allowance)
Tone Control Range:
Bass:
±12 dB (60 Hz, 80 Hz, 100 Hz, 120 Hz)
Mid-range:
±12 dB (500 Hz, 1 kHz, 1.5 kHz, 2.5 kHz)
Treble:
±12 dB (7.5 kHz, 10 kHz, 12.5 kHz, 15 kHz)
Q (Q-slope):
Q0.5 to Q2.0
Frequency Response:
40 Hz to 20 000 Hz
Signal-to-Noise Ratio:
70 dB
Line-Out Level/Impedance:
2.5 V/20 kΩ load (full scale)
Subwoofer-Out Level/Impedance:
2.5 V/20 kΩ load (full scale)
Output Impedance:
1 kΩ
Other Terminal:
AUX (auxiliary) input jack, iPod connector
TUNER SECTION
Frequency Range:
FM Tuner
AM Tuner
FM:
87.5 MHz to 108.0 MHz
AM:
531 kHz to 1 602 kHz
Usable Sensitivity:
11.3 dBf (1.0 μV/75 Ω)
50 dB Quieting Sensitivity:
16.3 dBf (1.8 μV/75 Ω)
Alternate Channel Selectivity (400 kHz):
65 dB
Frequency Response:
40 Hz to 15 000 Hz
Stereo Separation:
30 dB
Sensitivity:
20 μV
Selectivity:
35 dB
22
EN14-23_KD-PDR45[U]_7.indd 22
11/27/07 9:03:31 AM
Type:
Compact disc player
Signal Detection System:
Non-contact optical pickup
(semiconductor laser)
Number of Channels:
2 channels (stereo)
Frequency Response:
5 Hz to 20 000 Hz
Dynamic Range:
96 dB
Signal-to-Noise Ratio:
98 dB
Wow and Flutter:
Less than measurable limit
ENGLISH
CD PLAYER SECTION
MP3 Decoding Format:
(MPEG1/2 Audio Layer 3)
Max. Bit Rate:
320 kbps
WMA (Windows Media® Audio)
Decoding Format:
Max. Bit Rate:
320 kbps
Operating Voltage:
DC 14.4 V (11 V to 16 V allowance)
GENERAL
Power Requirement:
Grounding System:
Negative ground
Allowable Operating Temperature:
0°C to +40°C
Dimensions (W × H × D): (approx.) Installation Size:
182 mm × 52 mm × 160 mm
Panel Size:
Mass:
188 mm × 58 mm × 6 mm
1.3 kg (excluding accessories)
Design and specifications are subject to change without notice.
23
EN14-23_KD-PDR45[U]_5.indd 23
11/13/07 12:14:49 PM
Having TROUBLE with operation?
Please reset your unit
Refer to page of How to reset your unit
EN, CT
© 2007 Victor Company of Japan, Limited
Rear_KD-PDR45[U]_005A.indd 2
1107DTSMDTJEIN
11/28/07 11:05:14 AM
KD-PDR45
Installation/Connection Manual
安裝/連接手冊
GET0489-010A
1107DTSMDTJEIN
[UT]
EN, CT
© 2007 Victor Company of Japan, Limited
中文
ENGLISH
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does
not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
本機僅可使用直流 12 V、負極接地的電源系統。如果您的車輛沒有這一電源系統,則需要一個電
壓變換器,可以在 JVC 汽車音響分銷商處買到。
WARNINGS
警告
To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all
electrical connections before installing the unit.
• Be sure to ground this unit to the car’s chassis again after installation.
為防止短路,建議在安裝本機之前,拔開電池的負極,並把所有電路都連接好。
• 安裝完畢後務必將本機的地線重新接至車身。
注意:
• 把保險絲更換為額定負荷值的保險絲。如果保險絲經常燒壞,請向 JVC 汽車音響分銷商詢問。
• 後置和前置揚聲器的最大輸入功率應大於 50 W,其阻抗為 4 Ω - 8 Ω。如果最大功率小於 50 W,
請調校“AMP GAIN”設定值,以防止揚聲器損壞。(參閱使用說明書的第 15 頁。)
• 為防止電源短路,請用絕緣帶包住未使用電線的端子。
• 本機使用後,散熱片會很熱。因此,在移出本機時,小心不要觸摸散熱片。
Notes:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio
dealer.
• It is recommended to connect speakers with a maximum power of more than 50 W (both at the rear and
at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 50 W, change “AMP
GAIN” setting to prevent the speakers from being damaged (see page 15 of the INSTRUCTIONS).
• To prevent short circuits, cover the terminals of the UNUSED leads with insulating tape.
• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.
Heat sink / 散熱片
PRECAUTIONS on power supply and speaker connections:
電源和揚聲器接線注意事項:
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit
will be seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in
your car.
• 切勿把揚聲器導線接頭接至電池,否則本機將會嚴重損壞。
• 在把揚聲器導線接頭接至揚聲器之前,檢查您汽車上的揚聲器線路。
Parts list for installation and connection
用於安裝和連接的零組件清單
The following parts are provided for this unit. If any item is missing, consult your JVC car audio dealer
immediately.
下列零組件隨本機提供。若有任何遺漏,立刻咨詢您的 JVC 汽車音響經銷商。
A/B
Hard case/Control panel
硬盒/控制面板
C
Sleeve
外套機殼
F
Direct connection cable for iPod
iPod 直接連接電纜
G
Washer (ø5)
墊圈(ø5)
J
Rubber cushion
橡膠防震墊
K
Handles
板條型把手
D
Trim plate
裝飾框
H
Lock nut (M5)
鎖定螺母(M5)
L
Remote controller
搖控器
E
Power cord
電路連接用的配線束
I
Mounting bolt (M4 × 5 mm;M5 × 12.5 mm)
緊固螺栓(M4 × 5 mm;M5 × 12.5 mm)
M
Battery
電池
1
Install1_KD-PDR45_009A_4.indd 1
11/27/07 15:47:48
INSTALLATION (IN-DASH MOUNTING)
安裝(裝設、固定在儀表板內)
The following illustration shows a typical installation. If you have any questions or require information
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
下面的圖解表示了典型的安裝程序。如果您有問題,或需要有關配套元件的資料,請向 JVC
汽車音響分銷商或配套元件供應公司詢問。
• 如果您不能確定如何正確地安裝本機,應請合格的技術人員來安裝。
Do the required electrical connections.
進行所需的電路連接。
Bend the appropriate tabs to hold the
sleeve firmly in place.
弄彎機殼的突舌,把外套機殼牢固在儀
表板內。
Removing the unit
拆卸本機
Before removing the unit, release the rear section.
在拆卸本機前,應將本機後部的固定和連接部分鬆開。
Insert the two handles, then pull them as
illustrated so that the unit can be removed.
按圖所示,將兩片板條型把手插入卡槽,
然後輕穩地從兩側向外拉兩片把手,本機
隨之拉出。
When using the optional stay / 若選用支撐架
Stay (option)
支撐架(選用的)
When installing the unit without using the sleeve / 若不使用外套機殼安裝本機
In a Toyota car for example, first remove the car radio and install the unit in its place.
以豐田牌(TOYOTA)汽車為例:首先取出汽車收音機,然後將本機裝入其空出的位置。
Fire wall
防火板
Flat head screws (M5 × 8 mm) *2
平頭螺絲釘(M5 × 8 mm)*2
Dashboard
儀表板
Bracket*2
托座 *2
Screw (option)
螺絲釘(選用的)
Flat head screws (M5 × 8 mm) *2
平頭螺絲釘(M5 × 8 mm)*2
Pocket
空殼
Bracket *2
托座*2
Install the unit at an angle of less than 30˚.
將本機安裝在少於 30˚ 的角度。
Note :When installing the unit on the mounting bracket, make sure to use the 8 mm -long screws. If longer screws are used,
they could damage the unit.
注意 :把本機安裝在托座上時,務必使用 8 mm 長的螺絲釘。如使用過長的螺絲釘,會損壞本機。
*1 When you stand the unit, be careful not to damage the fuse on the rear.
*2 Not supplied for this unit.
*1
*2
您豎起本機時,小心不要損壞底部的保險絲。
不隨本機提供。
2
Install1_KD-PDR45_009A_4.indd 2
11/27/07 16:38:51
中文
ENGLISH
電路連接
ELECTRICAL CONNECTIONS
A
Typical connections / 典型的接線方法
接線前:仔細檢查汽車內的線路。不正確的接線會導致本機嚴重損壞。
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious
damage to this unit.
The leads of the power cord and those of the connector from the car body may be different in color.
1
2
3
電源線的引線和車身的連接器引線在顏色上可能有所不同。
1
2
3
Connect the colored leads of the power cord in the order specified in the illustration below.
Connect the antenna cord.
Finally connect the wiring harness to the unit.
依照下圖所示之次序連接電源線的顏色導線。
將天線的電線連接起來。
最後,把配線束的插頭插在本機上。
Rear ground terminal
本機後背接地端子
Line out (see diagram )
線性輸出(參閱圖表 )
15 A fuse
15 A 保險絲
Antenna terminal
天線端子
iPod connector (see diagram )
iPod 連接器(參閱圖表 )
Ignition switch
點火開關
Black
黑色
To the metallic body or chassis of the car
接至金屬體或汽車底盤
Yellow *2
黃色 *2
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
接至保險絲單元內的帶電端子,保險絲單元與車裝電池相連接
(用於旁路點火開關)(恆定 12 V)
Fuse block
保險絲單元
Red
紅色
To an accessory terminal in the fuse block
接至保險絲單元內的附屬端子
Blue
藍色
To the automatic antenna if any (250 mA max.)
接至自動天線(若有裝設)(最大 250 mA)
Blue with white stripe
藍色帶有白色條紋
White with black stripe
白色帶有黑色條紋
White
白色
Gray with black stripe
灰色帶有黑色條紋
Left speaker (front)
左揚聲器(前置)
Gray
灰色
To the remote lead of other equipment (200 mA max.)
連接至其他裝置上的遙控導線(最大 200 mA)
Green with black stripe
綠色帶有黑色條紋
Right speaker (front)
右揚聲器(前置)
Green
綠色
Purple with black stripe
紫色帶有黑色條紋
Left speaker (rear)
左揚聲器(後置)
*1 Not supplied for this unit.
*2 Before checking the operation of this unit prior to installation, this lead must be connected, otherwise the
Purple
紫色
Right speaker (rear)
右揚聲器(後置)
*1 不隨本機提供。
*2 本機未安裝時,進行工作狀況檢查之前,必須把這導線接上,否則不能開啟電源。
power cannot be turned on.
3
Install2_KD-PDR45_009A_3.indd 3
11/14/07 15:12:45
B
Connecting the external amplifier or subwoofer / 連接至外部功率放大器或重低音揚聲器
You can connect an amplifier to upgrade your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it
can be controlled through this unit.
• Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker
leads of this unit unused.
您可以連接功率放大器以提昇尊車的音響系統。
• 將遙控導線(藍色帶有白色條紋)和其他裝置上的遙控導線連接起來,以便可以經由本機進行
遙控。
• 將揚聲器和本機拔開,再接上功率放大器。將本機的揚聲器接線放置不用。
Remote lead
遙控導線
Y-connector (not supplied for this unit)
Y-型連接導線(不隨本機提供)
Remote lead (blue with white stripe)
遙控導線(藍色帶有白色條紋)
Set “L/O MODE” to “REAR” (See page 15 of the
INSTRUCTIONS.)
將“L/O MODE”設定為“REAR”(參閱使用
說明書的第 15 頁。)
Rear speakers
後置揚聲器
To the remote lead of other equipment or automatic
antenna if any
連接至其他裝置上的遙控導線或自動天線
(若有裝設)
JVC Amplifier
JVC 功率放大器
Signal cord (not supplied for this unit)
信號導線(不隨本機提供)
Set “L/O MODE” to “SUB.W” (See page 15 of the
INSTRUCTIONS.)
將“L/O MODE”設定為“SUB.W”(參閱使用
說明書的第 15 頁。)
Subwoofer
重低音揚聲器
C
JVC Amplifier
JVC 功率放大器
Front speakers
前置揚聲器
or
或
Connecting an Apple iPod / 連接 Apple iPod
You can connect an iPod to this unit using the supplied direct connection cable for iPod.
您可以使用附帶的 iPod 直接連接電纜將 iPod 和本機連接起來。
Apple iPod (separately purchased)
Apple iPod(另購)
iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
iPod 是 Apple Inc.(蘋果公司)在美國及其他國家
註冊的商標。
Direct connection cable for iPod (supplied)
iPod 直接連接電纜(附帶)
*3 將地線與金屬車體或者汽車底盤緊密連接,連接處應該沒有被油漆覆蓋(如果已塗上油漆,在連接電
*3 Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint
線前,將油漆刮去)。如果不這樣做,可能會損壞本機。
(if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the
unit.
故障排除
TROUBLESHOOTING
• The fuse blows.
* Are the red and black leads connected correctly?
• 保險絲燒斷。
* 檢查紅色導線接頭和黑色導線接頭是否接觸正確?
• Power cannot be turned on.
* Is the yellow lead connected?
• 電源不能接通。
* 檢查黃色導線接頭是否接上?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• 揚聲器沒有聲音。
* 檢查揚聲器輸出導線接頭是否短路?
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• 聲音失真。
* 檢查揚聲器輸出端子是否接地?
* 檢查揚聲器的左(L)、右(R)端子的負極“–”是否共同接地?
• Noise interfere with sounds.
* Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?
• 噪音干擾音響。
* 後接地端子與車身是否使用較短和較厚的電線連接?
• This unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• 本機發熱。
* 檢查揚聲器輸出端子是否接地?
* 檢查揚聲器的左(L)、右(R)端子的負極“–”是否共同接地?
• This unit does not work at all.
* Have you reset your unit?
• 本機完全不能操作。
* 您是否已經重置您的機組?
4
Install2_KD-PDR45_009A_3.indd 4
11/14/07 15:12:54
CD RECEIVER
KD-S35
ENGLISH
RECEPTOR CON CD
KD-S35
ESPAÑOL
For canceling the display demonstration, see page 6.
Para cancelar la demostración en pantalla, consulte la página 6.
For installation and connections, refer to the separate manual.
Para la instalación y las conexiones, refiérase al manual separado.
INSTRUCTIONS
MANUAL DE INSTRUCCIONES
For customer Use:
Enter below the Model
No. and Serial No. which
are located on the top or
bottom of the cabinet. Retain
this information for future
reference.
Model No.
Serial No.
GET0563-001A
[J]
Cover_KD-S35[J]_1.indd 1
5/5/08 3:25:14 PM
ENGLISH
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best
possible performance from the unit.
INFORMATION (For U.S.A.)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Caution:
Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to
qualified service personnel.
3. CAUTION: (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam.
(For Canada) Visible and/or invisible class 1M laser radiation when open. Do not view directly with
optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
For safety...
[European Union only]
Warning:
If you need to operate the unit while driving, be
sure to look around carefully or you may be involved
in a traffic accident.
• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
• Stop the car before performing any complicated
operations.
Temperature inside the car...
If you have parked the car for a long time in hot or cold
weather, wait until the temperature in the car becomes
normal before operating the unit.
2
EN02-05_KD-S35[J]_1.indd 2
5/5/08 3:23:46 PM
CONTENTS
Control panel .................................. 4
Remote controller — RM-RK50........... 5
Getting started ................................ 6
ENGLISH
How to reset your unit
Basic operations ................................................... 6
• Your preset adjustments will also be erased.
How to forcibly eject a disc
• Be careful not to drop the disc when it ejects.
• If this does not work, reset your unit.
How to use the M MODE button
If you press M MODE, the unit goes into functions mode,
then the number buttons and 5/∞ buttons will work
as different function buttons.
Ex.: When number button 2 works as
MO (monaural) button.
Radio operations ............................. 7
Disc operations ................................ 8
Playing a disc in the unit ..................................... 8
iPod operations ...............................
Sound adjustments ..........................
General settings — PSM ..................
Other external component
operations ...................................
Title assignment..............................
Maintenance ...................................
More about this unit ........................
Troubleshooting ..............................
Specifications ..................................
10
12
14
16
16
17
17
20
22
Detaching the control panel
To use these buttons for their original functions
again after pressing M MODE, press M MODE again.
• Waiting for about 5 seconds without pressing any of
these buttons will automatically cancels the functions
mode.
Attaching the control panel
3
EN02-05_KD-S35[J]_1.indd 3
5/5/08 3:23:48 PM
ENGLISH
Control panel
Parts identification
Display window
1
2
3
4
5
6
7
8
9
p
q
w
e
r
t
y
u
i
5 (up) / ∞ (down) buttons
0 (eject) button
(standby/on attenuator) button
Control dial
Remote sensor
DO NOT expose the remote sensor to strong light
(direct sunlight or artificial lighting).
BAND button
Loading slot
Display window
EQ (equalizer) button
DISP (display) button
(control panel release) button
i (iPod) button
4 /¢ buttons
SRC (source) button
SEL (select) button
M MODE button
MO (monaural) button
SSM (Strong-station Sequential Memory) button
o
;
a
s
d
f
g
h
j
k
l
/
z
x
Number buttons
RPT (repeat) button
RND (random) button
AUX (auxiliary) input jack
Source display / Track number / Folder number /
Time countdown indicator
Tr (track) indicator
DISC indicator
Playback mode / item indicators— RND (random),
(disc), (folder), RPT (repeat)
Tuner reception indicators—ST (stereo),
MO (monaural)
Sound mode (iEQ: intelligent equalizer) indicators
—CLASSIC, HIP HOP, JAZZ, ROCK, POPS, USER
LOUD (loudness) indicator
EQ (equalizer) indicator
Disc information indicators—
TAG (Tag information), (folder), (track/file)
Main display
4
EN02-05_KD-S35[J]_1.indd 4
5/5/08 3:23:49 PM
Remote controller — RM-RK50
ENGLISH
Main elements and features
Installing the lithium coin battery
(CR2025)
1
For USA-California Only:
This product contains a CR Coin Cell Lithium Battery
which contains Perchlorate Material—special
handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
2
Aim the remote controller directly at the remote
sensor on the unit. Make sure there is no obstacle
in between.
Warning:
• Do not install any battery other than CR2025 or its
equivalent; otherwise, it may explode.
• Do not leave the remote controller in a place
(such as the dashboard) exposed to direct
sunlight for a long time; otherwise, it may
explode.
• Store the battery in a place where children cannot
reach to avoid the risk of accidents.
• To prevent the battery from over-heating,
cracking, or starting a fire:
– Do not recharge, short, disassemble, heat the
battery, or dispose of it in a fire.
– Do not leave the battery with other metallic
materials.
– Do not poke the battery with tweezers or
similar tools.
– Wrap the battery with tape and insulate when
throwing away or saving it.
3
4
5
6
(standby/on/attenuator) button
• Turns the power on if pressed briefly or
attenuates the sound when the power is on.
• Turns the power off if pressed and held.
5 U (up) / D (down) ∞ buttons
• Changes the FM/AM bands with 5 U.
• Changes the preset stations with D ∞.
• Changes the folder of the MP3/WMA discs.
• While listening to an Apple iPod.
– Enters the main menu if pressed and held.
(Now 5 U/D ∞/2 R/F 3 work as the menu
selecting buttons.)
• While listening to an iPod (in menu selecting
mode):
– Returns to the previous menu if pressed 5 U
briefly.
– Selects an item if pressed D ∞ briefly. (Then,
press and hold D ∞ to play back the selection
directly.)
VOL – / VOL + buttons
• Adjusts the volume level.
SOUND button
• Selects the sound mode (iEQ: intelligent equalizer).
SOURCE button
• Selects the source.
2 R (reverse) / F (forward) 3 buttons
• Searches for stations if pressed briefly.
• Fast-forwards or reverses the track if pressed and
held.
• Changes the track if pressed briefly.
• While listening to an iPod (in menu selecting
mode):
– Accelerated file search: Hold 2 R/F 3 to fast
skip during song search in the main menu.
5
EN02-05_KD-S35[J]_1.indd 5
5/5/08 3:23:50 PM
ENGLISH
Getting started
Basic operations
~
Turn on the power.
To drop the volume in a
moment (ATT)
To restore the sound, press
the button again.
To turn off the power
Ÿ
Basic settings
• See also “General settings — PSM” on pages
14 and 15.
1
*1 You cannot select “CD” as the playback source
if there is no disc in the unit.
*2 “NO IPOD” appears if an iPod is not connected.
!
2
1 Canceling the display demonstrations
For FM/AM tuner
Select “DEMO,” then “DEMO OFF.”
2 Setting the clock
⁄
Select “CLOCK HOUR,” then adjust the hour.
Select “CLOCK MIN” (minute), then adjust the
minute.
Adjust the volume.
3
Volume level appears.
@
Adjust the sound as you want. (See
pages 12 and 13.)
Finish the procedure.
To check the current clock time while the
power is turned off
Clock time is shown on the display for
about 5 seconds. See also page 14.
Caution on volume setting:
Discs produce very little noise compared with other
sources. Lower the volume before playing a disc
to avoid damaging the speakers by the sudden
increase of the output level.
6
EN06-13_KD-S35[J]_1.indd 6
5/5/08 3:24:37 PM
When an FM stereo broadcast is hard to
receive
~
Lights up when monaural mode is activated.
ENGLISH
Radio operations
Ÿ
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
!
Reception improves, but the stereo effect will be lost.
To restore the stereo effect, repeat the same
procedure. “MONO OFF” appears and the MO indicator
goes off.
Start searching for a station.
Storing stations in memory
You can preset six stations for each band.
When a station is received, searching stops.
To stop searching, press the same button
again.
FM station automatic presetting—
SSM (Strong-station Sequential
Memory)
1
To tune in to a station manually
Select the FM band (FM1 – FM3) you want to
store into.
In step ! above...
1
2
3
2 Select a desired station frequency.
“SSM” flashes, then disappears when automatic
presetting is over.
Local FM stations with the strongest signals are
searched and stored automatically in the FM band.
7
EN06-13_KD-S35[J]_1.indd 7
5/5/08 3:24:40 PM
ENGLISH
Manual presetting
Ex.: Storing the FM station of 92.50MHz into preset
number 4 of the FM1 band.
1
Disc operations
Playing a disc in the unit
All tracks will be played repeatedly until you change the
source or eject the disc.
2
3
To stop play and eject the disc
Preset number flashes for a while.
Listening to a preset station
1
2
• Press SRC to listen to another
playback source.
[Hold] To fast-forward or reverse the
track
Select the preset station (1 – 6) you want.
[Press] To go to the next or previous
track
or
[Press] To go to the next or previous
folder (only for MP3 or WMA
discs)
To locate a particular track (for CD) or folder
(for MP3 or WMA discs) directly
To check other information while listening
to the radio
Frequency = Clock =
Station name * = (back to the
beginning)
To select a number from 01 – 06:
To select a number from 07 – 12:
* If no title is assigned to a station, “NO NAME” appears.
To assign a title to a station, see page 16.
8
EN06-13_KD-S35[J]_1.indd 8
5/5/08 3:24:41 PM
To select a particular track in a folder
(for MP3 or WMA discs):
Changing the display information
While playing an audio CD or CD Text
ENGLISH
• To use direct folder access on MP3/WMA discs, it
is required that folders are assigned with 2-digit
numbers at the beginning of their folder names—
01, 02, 03, and so on.
A = B = Disc title/performer *1 = Track
title *1 [ ] = (back to the beginning)
Other main functions
Skipping tracks quickly during play
• For MP3 or WMA discs, you can skip tracks within the
same folder.
Ex.: To select track 32 while playing a track whose
number is a single digit (1 to 9)
While playing an MP3 or a WMA track
• When “TAG DISPLAY” is set to “TAG ON”
(see page 15)
A = B = Album name/performer (folder
name *2) [
] = Track title (file
name *2) [
] = (back to the beginning)
• When “TAG DISPLAY” is set to “TAG OFF”
1
A = B = Folder name [ ] = File name
[ ] = (back to the beginning)
2
Each time you press the button, you can skip 10
tracks.
• After the last track, the first track will be selected
and vice versa.
3
A : Current track number with the elapsed playing
time
B : Current track number with the clock time
[ ] : Corresponding indicator lights up on the display.
*1 If the current disc is an audio CD, “NO NAME” appears.
*2 If an MP3/WMA file does not have Tag information,
folder name and file name appear. In this case, the
TAG indicator will not light up.
Prohibiting disc ejection
You can lock a disc in the loading slot.
“EJECT LOCK” flashes on the display.
To cancel the prohibition, repeat the same
procedure.
9
EN06-13_KD-S35[J]_1.indd 9
5/5/08 3:24:42 PM
ENGLISH
Selecting the playback modes
You can use only one of the following playback modes
at a time.
1
2
Select your desired playback mode.
iPod operations
You can play songs in an Apple iPod by connecting it
with the supplied direct connection cable for iPod.
You can control playback from the unit or from your
iPod.
• Disconnecting the iPod will stop playback. Press SRC
to listen to another playback source.
Caution:
7 Repeat play
Mode
Plays repeatedly
]
TRACK RPT : The current track. [
FOLDER RPT * : All tracks of the current folder.
[
]
RPT OFF
: Cancels.
7 Random play
Mode
Plays at random
• Avoid using the iPod if it might hinder your safety
while driving.
• Make sure all important data has been backed up
to avoid losing the data.
• For connection, see the Installation/Connection
Manual (separate volume).
• For details, refer also to the manual supplied for your
iPod.
~
Connect an iPod.
Direct connection
cable for iPod
FOLDER RND *: All tracks of the current folder,
then the tracks of the next folder
and so on. [
]
ALL RND
: All tracks of the current disc.
[
]
RND OFF
: Cancels.
* Only while playing an MP3 or a WMA disc.
If an iPod has been connected...
To directly select “IPOD” as the source
while listening to another source or
when the power is turned off.
[ ] : Corresponding indicator lights up on the
display.
Playback starts automatically from where it had
been paused previously.
Ÿ
Adjust the volume.
10
EN06-13_KD-S35[J]_1.indd 10
5/5/08 3:24:43 PM
Adjust the sound as you want. (See
pages 12 and 13.)
Selecting a track from the menu
1
To control playback from your iPod
Enter the main menu.
or
“IPOD MODE” appears on the
display.
• Press and hold this button again to control playback
from the unit. “HEAD MODE” appears on the display.
ENGLISH
!
Now the 5/∞/4 /¢ /number
buttons work as the menu selecting buttons.
2
Select the desired menu.
Playback control from the unit
[Press] Go to the next or previous
track
PLAYLIST Ô ARTIST Ô ALBUM Ô SONG
Ô PODCASTÔ GENRE Ô COMPOSER
Ô AUDIOBOOK Ô (back to the beginning)
[Hold] Fast-forward or reverse the
track during playback
Fast-skip the menu items of
the main menu
[Hold] Enter the main menu (see the
right column).
[Press] Pause/resume playback.
[Press] Go to the top menu of “PLAYLIST,” “ARTIST,”
“ALBUM,” “SONG,” “PODCAST,” or “GENRE” in
the main menu (see the right column).
• Pressing the number buttons can directly select
the desired menu (see the left column for
details).
3
Confirm the selection.
To move back to the previous
menu, press 5.
• Holding the button will start play back the
selected item directly.
• If a track is selected, playback starts
automatically.
• If the selected item has another layer, you will
enter the layer. Repeat steps 2 and 3 until the
desired track is played.
• Accelerated file search: Hold 4 /¢
to fast skip during song search in the main menu.
[Hold] Go to the top menu of “COMPOSER” or
“AUDIOBOOK” in the main menu (see the
right column).
Continued on the next page
11
EN06-13_KD-S35[J]_1.indd 11
5/5/08 3:24:45 PM
ENGLISH
To exit from menu selecting mode
To check other information while listening
to an iPod
or
* The menu selecting mode will be canceled:
– If no operations are performed for about
10 seconds.
– When you confirm the selection of a track.
– Pressing some other buttons such as DISP, SEL,
MODE, or EQ.
Current track number with the elapsed
playing time = Current track number with
the clock time = Track title * = Album name/
performer * = (back to the beginning)
* When “TAG DISPLAY” is set to “TAG OFF” (see page 15),
file name and folder name appear.
Selecting the playback modes
1
2
Sound adjustments
You can select a preset sound mode suitable to the
music genre (iEQ: intelligent equalizer).
Select your desired playback mode.
7 Repeat play
Mode
ONE RPT
ALL RPT
RPT OFF
Playback functions (as on iPod)
: Same as “Repeat One.” [
: Same as “Repeat All.” [
: Cancels.
Adjusting the sound
]
]
You can adjust the sound characteristics to your
preference.
• The adjustment you make will be stored for the
currently selected sound mode (iEQ) including
“USER.”
7 Random play
Mode
Playback functions (as on iPod)
SONG RND : Same as “Shuffle Songs.” [
ALBUM RND * : Same as “Shuffle Albums.”
[
]
RND OFF
: Cancels.
]
1
2
* Functions only if you select “ALL” in “ALBUMS” of
the main menu.
[ ] : Corresponding indicator lights up on the
display.
Indication, [Range]
FADER *2, [R06 to F06]
Adjust the front and rear speaker balance.
BALANCE *3, [L06 to R06]
Adjust the left and right speaker balance.
12
EN06-13_KD-S35[J]_1.indd 12
5/5/08 3:24:46 PM
3
Select a sound characteristic.
4
Adjust the sound elements of the selected
sound characteristic.
1 Adjust the frequency.
LOUD *4 (loudness), [LOUD ON or LOUD OFF]
Boost low and high frequencies to produce a
well-balanced sound at a low volume level.
SUBWOOFER *1, [00 to 08, initial: 04]
Adjust the subwoofer output level.
VOL ADJ (volume adjust), [–05 to +05, initial: 00]
Adjust the volume level of each source (except FM), in
relation to the FM volume level. The volume level will
automatically increase or decrease when you change
the source.
• Before making an adjustment, select the source you
want to adjust.
ENGLISH
Indication, [Range]
2 Adjust the level.
VOLUME, [00 to 50 or 00 to 30 ]*5
Adjust the volume.
3 Adjust the quality slope (Q).
*1 Displayed only when “L/O MODE” is set to “SUB.W”
(see page 15).
*2 If you are using a two-speaker system, set the fader
level to “00.”
*3 This adjustment will not affect the subwoofer output.
*4 The adjustment made (LOUD ON/LOUD OFF) will be
applied to all sound modes.
*5 Depending on the amplifier gain control setting. (See
page 15 for details.)
Sound
elements
Range/selectable items
BASS
MID
TRE
Frequency
60 Hz
80 Hz
100 Hz
120 Hz
500 Hz
1.0 kHz
1.5 kHz
2.5 kHz
7.5 kHz
10.0 kHz
12.5 kHz
15.0 kHz
You can adjust the sound modes and store your own
adjustments in memory.
Level
–06 to
+06
–06 to
+06
–06 to
+06
1
Select a sound mode.
Q (Q-slope)
Q0.5
Q1.0
Q1.5
Q2.0
Q0.75
Q1.0
Q1.25
Q1.5
Q0.75
Q1.25
2
Enter the adjustment mode.
• If no operation is done within
5 seconds, this mode is canceled.
BASS: Bass MID: Mid-range TRE: Treble
Storing your own sound mode
5
The adjustment made will be stored
automatically. Repeat steps 3 and 4 to adjust
other sound characteristics.
13
EN06-13_KD-S35[J]_1.indd 13
5/5/08 3:24:47 PM
ENGLISH
General settings — PSM
You can change PSM (Preferred Setting Mode) items
listed in the table below and on page 15.
3
Adjust the PSM item selected.
4
Repeat steps 2 and 3 to adjust other PSM
items if necessary.
5
Finish the procedure.
1
2
Select a PSM item.
Indications
Item
( : Initial)
Setting, [reference page]
DEMO
Display
demonstration
• DEMO ON
: The display demonstration will be activated automatically if no
operation is done for about 20 seconds, [6].
: Cancels.
CLOCK DISP *
Clock display
• CLOCK ON
1
• DEMO OFF
• CLOCK OFF
: The clock time is shown on the display at all times when the power is
turned off.
: Cancels; pressing DISP will show the clock time for about 5 seconds
when the power is turned off, [6].
CLOCK HOUR
Hour adjustment
1 – 12
[Initial: 1 (1:00)], [6].
CLOCK MIN
Minute adjustment
00 – 59
[Initial: 00 (1:00)], [6].
DIMMER
Dimmer
• ON
• OFF
: Dims the display and button illumination.
: Cancels.
*1 If the power supply is not interrupted by turning off the ignition key of your car, it is recommended that you select
“CLOCK OFF” to save the car’s battery.
14
EN14-23_KD-S35[J]_1.indd 14
5/5/08 3:23:07 PM
Item
( : Initial)
Setting, [reference page]
AUDIOBOOKS *2
Speed control of
“Audiobook”
• NORMAL
• FASTER
• SLOWER
: You can select the playback speed of the “Audiobook” sound file in
your iPod.
SCROLL *3
Scroll
• ONCE
• AUTO
• OFF
:
:
:
•
L/O MODE
Line output mode
• REAR
: Select if the REAR LINE OUT terminals are used for connecting the
speakers (through an external amplifier).
: Select if the REAR LINE OUT terminals are used for connecting a
subwoofer (through an external amplifier).
• SUB.W
ENGLISH
Indications
Scrolls the displayed information once.
Repeats scrolling (at 5-second intervals).
Cancels.
Pressing DISP for more than one second can scroll the display
regardless of the setting.
SUB.W FREQ *4
Subwoofer cutoff
frequency
• LOW
• MID
• HIGH
: Frequencies lower than 90 Hz are sent to the subwoofer.
: Frequencies lower than 135 Hz are sent to the subwoofer.
: Frequencies lower than 180 Hz are sent to the subwoofer.
TAG DISPLAY
Tag display
• TAG ON
• TAG OFF
: Shows the Tag information while playing MP3/WMA tracks, [9].
: Cancels.
AMP GAIN
Amplifier gain
control
• LOW POWER
IF BAND
Intermediate
frequency band
• AUTO
AREA
Tuner channel
interval
• AREA US
: VOLUME 00 – VOLUME 30. (Select this if the maximum power of the
speaker is less than 50 W to avoid damaging the speaker.)
• HIGH POWER : VOLUME 00 – VOLUME 50.
• WIDE
• AREA EU
• AREA SA
: Increases the tuner selectivity to reduce interference noise between
close stations. (The stereo effect may be lost.)
: Subject to interference noise from adjacent stations, but the sound
quality will not be degraded and the stereo effect will remain.
: When using in North/Central/South America. AM/FM intervals are
set to 10 kHz/200 kHz.
: When using in any other areas. AM/FM intervals are set to 9 kHz/
50 kHz (100 kHz during auto search).
: When using in South American countries where FM interval is
100 kHz. AM interval is set to 10 kHz.
*2 Displayed only when an iPod is connected and playback is controlled from the unit.
*3 Some characters or symbols will not be shown correctly (or will be blanked) on the display.
*4 Displayed only when “L/O MODE” is set to “SUB.W.”
15
EN14-23_KD-S35[J]_1.indd 15
5/5/08 3:23:11 PM
ENGLISH
Other external component
operations
You can connect an external component to the AUX
(auxiliary) input jack on the control panel.
Title assignment
You can assign names to 30 station frequencies (FM and
AM) and up to 8 characters for each station name.
1
Select FM/AM.
2
Show the title entry screen.
3
Assign a title.
1 Select a character.
Portable audio player, etc.
3.5 mm (3/16”) stereo
mini plug (not supplied)
~
Ÿ
!
Turn on the connected component and
start playing the source.
Adjust the volume.
2 Move to the next (or previous) character
position.
⁄
Adjust the sound as you want. (See
pages 12 and 13.)
3 Repeat steps 1 and 2 until you finish
entering the title.
To check other information while listening
to an external component
Clock Ô AUX IN
4
Finish the procedure.
To erase the entire title
In step 2 above...
16
EN14-23_KD-S35[J]_1.indd 16
5/5/08 3:23:11 PM
How to clean the connectors
Frequent detachment will deteriorate the connectors.
To minimize this possibility, periodically wipe the
connectors with a cotton swab or cloth moistened with
alcohol, being careful not to damage the connectors.
To play new discs
New discs may have some rough spots
around the inner and outer edges. If
such a disc is used, this unit may reject
the disc.
To remove these rough spots, rub the edges with a
pencil or ball-point pen, etc.
ENGLISH
Maintenance
Do not use the following discs:
Single CD
—8 cm (3-3/16”) disc
Warped disc
Sticker and
sticker residue
Stick-on label
Connectors
Moisture condensation
Moisture may condense on the lens inside the unit in
the following cases:
• After starting the heater in the car.
• If it becomes very humid inside the car.
Should this occur, the unit may malfunction. In this
case, eject the disc and leave the unit turned on for a
few hours until the moisture has evaporated.
Unusual shape
How to handle discs
Center holder
When removing a disc from its
case, press down the center holder
of the case and lift the disc out,
holding it by the edges.
• Always hold the disc by the edges. Do not touch its
recording surface.
When storing a disc in its case, gently insert the
disc around the center holder (with the printed surface
facing up).
• Make sure to store discs in cases after use.
To keep discs clean
A dirty disc may not play correctly.
If a disc does become dirty, wipe it with
a soft cloth in a straight line from center
to edge.
• Do not use any solvents (for example, conventional
record cleaner, spray, thinner, benzine, etc.) to clean
discs.
More about this unit
Basic operations
Turning on the power
• By pressing SRC (source) or i (iPod) button on the
unit, you can also turn on the power. If the source is
ready, playback also starts.
Turning off the power
• If you turn off the power while listening to a track,
playback will start from where it had been stopped
previously next time you turn on the power.
Continued on the next page
17
EN14-23_KD-S35[J]_1.indd 17
5/5/08 3:23:13 PM
ENGLISH
General
Playing a CD-R or CD-RW
• If you change the source while listening to a disc or
an iPod, playback stops.
Next time you select “CD” or “IPOD” as the playback
source, playback will start from where it had been
stopped/paused previously.
• After ejecting a disc or disconnecting an iPod,
“NO DISC” or “NO IPOD” appears and you cannot
operate some of the buttons. Insert another disc,
connect an iPod, or press SRC to select another
playback source.
• Use only “finalized” CD-Rs or CD-RWs.
• This unit can only play back files of the same type as
those which are detected first if a disc includes both
audio CD (CD-DA) files and MP3/WMA files.
• This unit can play back multi-session discs; however,
unclosed sessions will be skipped while playing.
• Some CD-Rs or CD-RWs may not play back on this
unit because of their disc characteristics, or for the
following reasons:
– Discs are dirty or scratched.
– Moisture condensation has occurred on the lens
inside the unit.
– The pickup lens inside the unit is dirty.
– The files on the CD-R/CD-RW are written using the
“Packet Write” method.
– There are improper recording conditions (missing
data, etc.) or media conditions (stained, scratched,
warped, etc.).
• CD-RWs may require a longer readout time since the
reflectance of CD-RWs is lower than that of regular CDs.
• Do not use the following CD-Rs or CD-RWs:
– Discs with stickers, labels, or a protective seal stuck
to the surface.
– Discs on which labels can be directly printed by an
ink jet printer.
Using these discs under high temperature or high
humidity may cause malfunctions or damage to the
unit.
Tuner operations
Storing stations in memory
• During SSM search...
– All previously stored stations are erased and the
stations are stored anew.
– Received stations are preset in No. 1 (lowest
frequency) to No. 6 (highest frequency).
– When SSM is over, the station stored in No. 1 will
be automatically tuned in.
• When storing a station manually, the previously
preset station is erased when a new station is stored
in the same preset number.
Disc operations
Caution for DualDisc playback
• The Non-DVD side of a “DualDisc” does not comply
with the “Compact Disc Digital Audio” standard.
Therefore, the use of Non-DVD side of a DualDisc on
this product may not be recommended.
General
• This unit has been designed to reproduce
CDs/CD Texts, and CD-Rs (Recordable)/CD-RWs
(Rewritable) in audio CD (CD-DA), MP3 and WMA
formats.
• When a disc is inserted upside down, “PLEASE” and
“EJECT” appear alternately on the display. Press 0 to
eject the disc.
• MP3 and WMA “tracks” (words “file” and “track” are
used interchangeably) are recorded in “folders.”
• While fast-forwarding or reversing on an MP3 or
WMA disc, you can only hear intermittent sounds.
Playing an MP3/WMA disc
• This unit can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of
the letter case—upper/lower).
• This unit can show the names of albums, artists
(performer), and Tag (Version 1.0, 1.1, 2.2, 2.3, or
2.4) for MP3 files and for WMA files.
• This unit can display only one-byte characters. No
other characters can be correctly displayed.
• This unit can play back MP3/WMA files meeting the
conditions below:
– Bit rate: 8 kbps — 320 kbps
– Sampling frequency:
48 kHz, 44.1 kHz, 32 kHz (for MPEG-1)
24 kHz, 22.05 kHz, 16 kHz (for MPEG-2)
18
EN14-23_KD-S35[J]_1.indd 18
5/5/08 3:23:17 PM
•
•
•
•
Ejecting a disc
• If the ejected disc is not removed within 15 seconds,
it is automatically inserted into the loading slot again
to protect it from dust. Playback starts automatically.
iPod operations
• Controllable iPod:
– iPod mini
– iPod G4
– iPod photo
– iPod nano (1st & 2nd Generation)
– iPod with video (5th Generation)
• Update your iPod to the latest software version
before using it with this unit.
• When you turn on this unit, the iPod is charged
through this unit.
• While connecting an iPod with Video:
– No video shows on the iPod’s display or the
external monitor (only the audio part is available).
– It is not possible to browse video files on the
“Video“ menu. (If you connect the iPod during
the playback or pausing of a video file, resuming
playback will not work.)
• iPod shuffle cannot be used with this unit.
• You can control the iPod from this unit when “JVC” or
“ ” appears on the iPod display after connection.
• The song order displayed on the selection menu of
this unit may differ from that of the iPod.
• If playback is stopped, select a track from the
selection menu or press BAND to playback the same
track again.
• The text information may not be displayed correctly:
– Some characters such as accented letters cannot be
shown correctly on the display.
– Communication between the iPod and the unit is
not stable.
• If the text information includes more than
11 characters, it scrolls on the display. This unit can
display up to 64 characters.
ENGLISH
•
– Disc format: ISO 9660 Level 1/Level 2, Romeo,
Joliet, Windows long file name
The maximum number of characters for file/folder
names vary depending on the disc format used
(includes 4 extension characters—<.mp3> or
<.wma>).
– ISO 9660 Level 1: up to 12 characters
– ISO 9660 Level 2: up to 31 characters
– Romeo: up to 128 characters
– Joliet: up to 64 characters
– Windows long file name: up to 128 characters
This unit can recognize a total of 512 files,
255 folders, and 8 hierarchical levels.
This unit can play back files recorded in VBR (variable
bit rate).
Files recorded in VBR have a discrepancy in the
elapsed time display, and do not show the actual
elapsed time. In particular, this difference becomes
noticeable after performing the search function.
This unit cannot play back the following files:
– MP3 files encoded in MP3i and MP3 PRO format.
– MP3 files encoded in an inappropriate format.
– MP3 files encoded with Layer 1/2.
– WMA files encoded in lossless, professional, and
voice format.
– WMA files which are not based upon Windows
Media® Audio.
– WMA files copy-protected with DRM.
– Files which have data such as AIFF, ATRAC3, etc.
The search function works but search speed is not
constant.
Notice:
When operating an iPod, some operations may not
be performed correctly or as intended. In this case,
visit the following JVC web site:
<http://www.jvc-victor.co.jp/english/car/>
General settings—PSM
• If you change the “AMP GAIN” setting from
“HIGH POWER” to “LOW POWER” while the
volume level is set higher than “VOLUME 30,” the
unit automatically changes the volume level to
“VOLUME 30.”
Continued on the next page
19
EN14-23_KD-S35[J]_1.indd 19
5/5/08 3:23:19 PM
ENGLISH
Preset value setting for each sound mode
Preset value
Sound mode
USER
ROCK
CLASSIC
POPS
HIP HOP
JAZZ
BASS (bass)
Freq. Level
60 Hz
00
100 Hz
+03
80 Hz
+01
100 Hz
+02
60 Hz
+04
80 Hz
+03
MID (mid-range)
Q
Q1.0
Q1.0
Q1.0
Q1.0
Q1.0
Q1.0
Freq. Level
1.0 kHz
00
1.0 kHz
00
1.0 kHz
00
1.0 kHz
+01
1.0 kHz
–02
1.0 kHz
00
Q
Q1.25
Q1.25
Q1.25
Q1.25
Q1.0
Q1.25
TRE (treble)
Freq. Level
7.5 kHz
00
10.0 kHz
+02
10.0 kHz
+03
10.0 kHz
+02
10.0 kHz
+01
10.0 kHz
+03
LOUD
(loudness)
Q
Q1.25
Q1.25
Q1.25
OFF
Q1.25
Q1.25
Q1.25
Freq.: Frequency Q: Q-slope
Troubleshooting
What appears to be trouble is not always serious. Check the following points before calling a service center.
FM/AM
General
Symptoms
Remedies/Causes
• Sound cannot be heard from the speakers.
• Adjust the volume to the optimum level.
• Check the cords and connections.
• The unit does not work at all.
Reset the unit (see page 3).
• SSM automatic presetting does not work.
Store stations manually.
• Static noise while listening to the radio.
Connect the antenna firmly.
• Disc cannot be played back.
Insert the disc correctly.
Disc playback
• CD-R/CD-RW cannot be played back.
• Insert a finalized CD-R/CD-RW.
• Tracks on the CD-R/CD-RW cannot be skipped. • Finalize the CD-R/CD-RW with the component which
you used for recording.
• Disc can neither be played back nor ejected.
• Unlock the disc (see page 9).
• Eject the disc forcibly (see page 3).
• Disc sound is sometimes interrupted.
• Stop playback while driving on rough roads.
• Change the disc.
• Check the cords and connections.
• “NO DISC” appears on the display.
• “PLEASE” and “EJECT“ appear alternately on
the display.
Insert a playable disc into the loading slot.
20
EN14-23_KD-S35[J]_f.indd 20
15/5/08 2:51:58 PM
MP3/WMA playback
Remedies/Causes
• Disc cannot be played back.
• Use a disc with MP3/WMA tracks recorded in a format
compliant with ISO 9660 Level 1, Level 2, Romeo, or
Joliet.
• Add the extension code <.mp3> or <.wma> to the
file names.
• Noise is generated.
Skip to another track or change the disc. (Do not add the
extension code <.mp3> or <.wma> to non-MP3 or
WMA tracks.)
ENGLISH
Symptoms
• A longer readout time is required (“READING” Do not use too many hierarchical levels and folders.
keeps flashing on the display).
• Tracks do not play back in the order you have The playback order is determined when the files are
intended them to play.
recorded.
• The elapsed playing time is not correct.
This sometimes occurs during playback. This is caused by
how the tracks are recorded on the disc.
iPod playback
• The correct characters are not displayed (e.g. This unit can only display letters (upper case), numbers,
album name).
and a limited number of symbols.
• The iPod does not turn on or does not work.
• Check the connecting cable and its connection.
• Update the firmware version.
• Charge the battery.
• The sound is distorted.
Deactivate the equalizer either on the unit or the iPod.
• “NO IPOD” appears on the display.
• Check the connecting cable and its connection.
• Charge the battery.
• Playback stops.
The headphones are disconnected during playback. Turn
off the unit’s power and turn it on again.
• No sound can be heard when connecting an
iPod nano.
• Disconnect the headphones from the iPod nano.
• Update the firmware version of the iPod nano.
• “NO FILES” appears on the display.
No tracks are stored. Import tracks to the iPod.
• The iPod’s controls do not work after
disconnecting from this unit.
Reset the iPod.
• “CANNOT PLAY” appears on the display.
Communication error occurs.
Disconnect and connect the cable to the iPod again.
21
EN14-23_KD-S35[J]_1.indd 21
5/5/08 3:23:21 PM
ENGLISH
Specifications
AUDIO AMPLIFIER SECTION
Power Output:
20 W RMS × 4 Channels at 4 Ω
and ≤ 1% THD+N
Signal-to-Noise Ratio:
80 dBA (reference: 1 W into 4 Ω)
Load Impedance:
4 Ω (4 Ω to 8 Ω allowance)
Tone Control Range:
Bass:
±12 dB (60 Hz, 80 Hz, 100 Hz, 120 Hz)
Mid-range:
±12 dB (500 Hz, 1 kHz, 1.5 kHz, 2.5 kHz)
Treble:
±12 dB (7.5 kHz, 10 kHz, 12.5 kHz, 15 kHz)
Q (Q-slope):
Q0.5 to Q2.0
Frequency Response:
40 Hz to 20 000 Hz
Line-Out Level/Impedance:
2.5 V/20 kΩ load (full scale)
Subwoofer-Out Level/Impedance:
2.5 V/20 kΩ load (full scale)
Output Impedance:
1 kΩ
Other Terminal:
AUX (auxiliary) input jack, iPod connector
TUNER SECTION
Frequency Range:
FM:
with channel interval set to 100 kHz 87.5 MHz to 107.9 MHz
or 200 kHz
with channel interval set to 50 kHz
AM: with channel interval set to 10 kHz
with channel interval set to 9 kHz
FM Tuner
AM Tuner
87.5 MHz to 108.0 MHz
530 kHz to 1 710 kHz
531 kHz to 1 602 kHz
Usable Sensitivity:
11.3 dBf (1.0 μV/75 Ω)
50 dB Quieting Sensitivity:
16.3 dBf (1.8 μV/75 Ω)
Alternate Channel Selectivity (400 kHz):
65 dB
Frequency Response:
40 Hz to 15 000 Hz
Stereo Separation:
35 dB
Sensitivity:
20 μV
Selectivity:
35 dB
22
EN14-23_KD-S35[J]_1.indd 22
7/5/08 2:36:37 PM
Type:
Compact disc player
Signal Detection System:
Non-contact optical pickup
(semiconductor laser)
Number of Channels:
2 channels (stereo)
Frequency Response:
5 Hz to 20 000 Hz
Dynamic Range:
96 dB
Signal-to-Noise Ratio:
98 dB
Wow and Flutter:
Less than measurable limit
MP3 Decoding Format:
(MPEG1/2 Audio Layer 3)
Max. Bit Rate:
320 kbps
WMA (Windows Media® Audio)
Decoding Format:
Max. Bit Rate:
320 kbps
ENGLISH
CD PLAYER SECTION
GENERAL
Power Requirement:
Operating Voltage:
DC 14.4 V (11 V to 16 V allowance)
Grounding System:
Negative ground
Allowable Operating Temperature:
0°C to +40°C (32°F to 104°F)
Dimensions (W × H × D): (approx.) Installation Size:
182 mm × 52 mm × 160 mm
(7-3/16” × 2-1/16” × 6-5/16”)
Panel Size:
Mass:
188 mm × 58 mm × 6 mm
(7-7/16” × 2-5/16” × 1/4”)
1.3 kg (2.9 lbs) (excluding accessories)
Design and specifications are subject to change without notice.
If a kit is necessary for your car, consult your telephone directory for the nearest car audio speciality shop.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
• iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
23
EN14-23_KD-S35[J]_1.indd 23
5/5/08 3:23:23 PM
Having TROUBLE with operation?
Please reset your unit
Refer to page of How to reset your unit
Still having trouble??
USA ONLY
Call 1-800-252-5722
http://www.jvc.com
We can help you!
EN, SP
© 2008 Victor Company of Japan, Limited
Rear_KD-S35[J]_1.indd 2
0508DTSMDTJEIN
5/5/08 3:26:03 PM
KD-S35
Installation/Connection Manual
Manual de instalación/conexión
0508DTSMDTJEIN
EN, SP
GET0563-002A
[J]
© 2008 Victor Company of Japan, Limited
ENGLISH
ESPAÑOL
PREPARATIONS
TROUBLESHOOTING
You need the installation kits which corresponds to your car.
• Mark all the check boxes (
) to make sure you have follow the instructions and the listed parts.
•
*
•
*
•
*
•
*
*
•
*
•
*
*
•
*
Check the battery system in your car
12 V DC, NEGATIVE ground
Prepare this before installation
The fuse blows.
Are the red and black leads connected correctly?
Power cannot be turned on.
Is the yellow lead connected?
No sound from the speakers.
Is the speaker output lead short-circuited?
Sound is distorted.
Is the speaker output lead grounded?
Are the “–” terminals of L and R speakers grounded in common?
Noise interfere with sounds.
Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?
This unit becomes hot.
Is the speaker output lead grounded?
Are the “–” terminals of L and R speakers grounded in common?
This unit does not work at all.
Have you reset your unit?
Parts list for installation and connection
A /B
C
D
E
Hard case/
Control panel
Sleeve
Trim plate
Power cord
F
G
H
I
Direct connection
cable for iPod
Washer (ø5)
Lock nut (M5)
Mounting bolt—
M4 × 5 mm (M4 × 1/4");
M5 × 12.5 mm (M5 × 1/2")
J
K
L
M
Rubber cushion
Handles
Remote controller
Battery
INSTALLATION
If you are not sure how to install this unit correctly, consult your JVC car audio dealer.
In dash-mounting
Removing the unit
Before removing the unit, release the rear section.
When you stand the unit, be careful
not to damage the fuse on the rear.
Do the required electrical
connections.
Bend the appropriate tabs
to hold the sleeve firmly
in place.
When installing the unit without using the sleeve
When using the optional stay
In a Toyota car for example, first remove the car radio and install the unit in its place.
Fire wall
Stay (option)
Flat type screws
—M5 × 8 mm (M5 × 3/8")*
Dashboard
* Not supplied for this unit.
Bracket*
Screw (option)
Install the unit at an angle of
less than 30˚.
Pocket
Flat type screws
—M5 × 8 mm (M5 × 3/8")*
Bracket*
1
Install_EN_KD-S35[J]_1.indd 1
6/5/08 4:41:33 PM
ELECTRICAL CONNECTIONS
Make sure to disconnect the battery’s negative terminal.
• Be sure to ground this unit to the car’s chassis again after installation.
Note:
It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω).
If the maximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 15 of the INSTRUCTIONS).
High
Heat sink
Typical connections
Rear line out
Antenna terminal
Connecting the external amplifiers and/or subwoofer
Rear ground terminal
Remote lead
15 A fuse
iPod connector
Remote lead (blue with white stripe)
Set “L/O MODE” to “REAR”
(See page 15 of the
INSTRUCTIONS.)
To the remote lead of other equipment
or automatic antenna if any
Ignition switch
Black
Connect only the front speakers if your
speaker system is two-speaker system.
White with black stripe
Yellow *2
Front speaker (left)
White
Gray with black stripe
Front speaker (right)
To metallic body or
chassis of the car
To a live terminal in the
fuse block connecting to the
car battery (bypassing the
ignition switch) (constant
12 V)
JVC Amplifier
Rear speakers
Front speakers
Fuse block
or
Set “L/O MODE” to “SUB. W”
(See page 15 of the INSTRUCTIONS.)
To an accessory terminal in
the fuse block
Gray
Green with black stripe
Rear speaker (left)
Red
Y-connector *1
Blue with white
stripe
Green
Remote lead
To the remote lead of other
equipment or automatic antenna if
any (200 mA max.)
JVC Amplifier
Subwoofer
Purple with black stripe
Rear speaker (right)
Purple
PRECAUTIONS on power supply and speaker connections
*1 Not supplied for this unit.
*2 Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power cannot be
turned on.
*3 Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place not coated with paint (if
coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.
*4 Signal cord (not supplied for this unit).
Connecting an Apple iPod
You can connect an iPod to this unit using the supplied direct connection cable for iPod.
iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
Apple iPod (separately purchased)
Direct connection cable for iPod (supplied)
2
Install_EN_KD-S35[J]_1.indd 2
6/5/08 4:41:36 PM