Specifications | Fujitsu FI-4860C All in One Printer User Manual

P3PC-E167-05EN
fi-4860C Image Scanner
Operator's Guide
INTRODUCTION
Thank you for purchasing the fi-4860C Duplex Color Scanner.
The fi-4860C is an image scanner designed to scan various documents in large
quantities. FUJITSU fi series image scanners are known for high reliability and this
scanner is no exceptions. The fi-4860C is designed to give you the best results for
your scanning need.
The fi-4860C has the following features.
High speed, high quality color scanning capabilities
Scans documents of Letter/A4 size at the speed of 60ppm/120ipm
@200dpi.
Highly reliable document handling
Accepts various thicknesses, sizes and types of documents.
Production ready
High capacity hopper 500 sheets of 20 lb or 80 g/m2 Letter/A4 size and
imprinter options. Duplex capability is available as standard feature.
About this manual
The manual provides the following information.
1. BASIC OPERATIONS
This chapter describes basic scanner operations and basic document
scanning.
2. SCANNING DOCUMENTS
This chapter describes how to scan various type of documents.
3. DAILY CARE
This chapter describes how to clean the scanner.
4. REPLACING CONSUMABLES
This chapter describes how to replace scanner consumables.
●i
5. SOLVING COMMON PROBLEMS
This chapter describes how to remedy document jams, other trouble,
and items to check before contacting the agent where you bought the
scanner, and how to check device labels.
6. ADF DOCUMENT SPECIFICATIONS
This chapter describes documents that can be used with this scanner.
7. OPERATOR PANEL MENUS
This chapter describes Setup-mode and Test-mode.
8. OPTIONS
This chapter describes the options available for this product.
9. SCANNER SPECIFICATIONS
This chapter lists the scanner specifications.
The “Installation Guide” is attached to this Scanner.
This guide contains necessary information for the scanner and the driver
installation, please also read the Installation Guide.
1. SCANNER BASICS
This chapter describes how to prepare the scanner for use.
2. INSTALLATION AND CONNECTIONS
This chapter describes how to install and connect the scanner, and how
to install the scanner application.
We hope that this manual is useful in taking full advantage of the fi-4860C Duplex
Color Scanner's features.
●ii
■ Regulatory Information
FCC Regulations
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•Reorient
or relocate the receiving antenna.
•Increase
the separation between the equipment and receiver.
•Connect
the equipment into an outlet on a circuit different from that to which the
receiver is located.
•Consult
your deealer or an expeerienced radio/TV technician.
FCC warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
ATTENTION
•
The use of a shielded interface cable is required to comply
with the Class A limits of Part 15 of FCC rules. The length of
the SCSI interface cable must be 1.5 meters (5 feet) or less.
•
The length of the AC cable must be 3 meters (10 feet) or
less.
Canadian DOC Regulations
This digital apparatus does not exceed the Class A limit for radio noise emissions
from digital apparatus set out in the Radio interference Regulations of the Canadian
Department of Communications.
This Class A digital apparatus complies with Canadian ICES-003.
●iii
Le pésent appareil numérique n’ément pas de bruits radioélectriques dépassant les
limites applicables aux appareils numériques de la classe A prescridtes dans le
Réglesment sur le brouillage radioélectrique dicté par le ministere des
Communications du Canada.
Cet appareil numérique de la classe A est conformme à la norme NMB-003 du
Canada.
●iv
Bescheinigung des Herstellers / Importeurs
Hiermit wird bescheinigt, daß der/die/das
fi-4860C
•
In Übereinsstimmung mit den Bestimmungen der AmtsblVfg 243/1991
funkentstört ist.
•Der Deutschen Bundesport wurde das Inverkehrbringen dieses Gerätes angezeigt
und die Berechtigung zur Überprüfung der Serie auf Einhaltung der
Bestimmungen eingeräumt.
•Maschinenlärminformationsverordnung
3. GS GV, 18.01.1991:Der höchste
Schalldruckpegel beträgt 70 dB (A) order weniger gemäß ISO/7779.
●v
International ENERGY STAR® Program
As an ENERGY STAR® Partner, PFU LIMITED has determined
that this product meets the ENERGY STAR® guidelines for energy
efficiency.
The International ENERGY STAR® Office Equipment Program is
an international program that promotes energy saving through the penetration of
energy efficient computers and other office equipment. The program backs the
development and dissemination of products with functions that effectively reduce
energy consumption. It is an open system in which business proprietors can
participate voluntarily. The targeted products are office equipment such as
computers, monitors, printers, facsimiles, copiers, scanners, and multifunction
devices. Their standards and logos (
) are uniform among participating
nations.
Use in High-safety Applications
This product has been designed and manufactured on the assumption that it will be
used in office, personal, domestic, regular industrial, and general-purpose
applications. It has not been designed and manufactured for use in applications
(simply called "high-safety applications" from here on) that directly involve serious
danger to life and health when an extremely high degree of safety is required, for
example, in the control of nuclear reactions at nuclear power facilities, automatic
flight control of aircraft, air traffic control, operation control in mass-transport
systems, medical equipment for sustaining life, and missile firing control in weapons
systems, and when provisionally the safety in question is not ensured. The user
should use this product with adopting measures for ensuring safety in such highsafety applications. PFU LIMITED assumes no liability whatsoever for damages
arising from use of this product by the user in high-safety applications, and for any
claims or compensation for damages by the user or a third party.
●vi
About the use of mercury
The scanner lamps contain mercury.
To avoid unexpected injury, read the followings carefully.
Doing following actions may result in serious personal injuries:
•Do
not put the substance in the lamp into your mouth as it contains mercury.
•Do
not incinerate, crush, or shred the lamps or scanner.
•Do
not breath the chemical liquid contained in the scanner parts.
Disposing of the scanner should be conducted as required by local ordinances or
regulations.
Illegal Copying
Reproducing bills, coins, government securities and passports, licenses issued by
public author or civilian organizations, official documents, private paper is illegal
and brought to justice
Copyright
Literary works like books, paintings, wood block prints, maps, drawings, and
photographs should not be reproduced without the rightful person’s permission.
●vii
Trademarks
Microsoft, Windows and Windows NT are registered trademarks of Microsoft
Corporation in the United States and/or other countries.
ISIS, QuickScan and their respective logos are trademarks or registered
trademarks of Pixel Translations, a division of Captiva Software Corporation in the
United States.
Adobe, the Adobe logo, and Acrobat are either registered trademarks of Adobe
Systems Incorporated in the United States and/or other countries.
Other product names are the trademarks or registered trademarks of the respective
companies.
How Trademarks Are Indicated In This Manual
References to operating systems (OS) are indicated as follows:
Windows 95:
Microsoft® Windows® 95 operating system.
Windows 98:
Microsoft® Windows® 98 operating system.
Windows Me:
Microsoft® Windows® Millennium Edition operating system.
Windows 2000: Microsoft® Windows® 2000 Professional operating system.
Windows XP:
Windows NT:
Microsoft® Windows® XP Professional operating system, and
Microsoft® Windows® XP Home Edition operating system.
Microsoft® Windows NT® 4.0 Server operating system and
Microsoft® Windows NT® 4.0 Workstation operating system.
Where there is no distinction between the different versions of the above operating
system, the general term "Windows“ is used.
Manufacturer
PFU LIMITED
Image Products Sales Dept, Imaging Products Division, Products Group
Solid Square East Tower, 580 Horikawa-cho, Saiwai-ku, Kawasaki-shi Kanagawa
212-8563, Japan
Phone: (81-44) 540-4538
All Rights Reserved, Copyright© PFU LIMITED 2005
●viii
■ Note, Liability
READ ALL OF THIS MANUAL CAREFULLY BEFORE USING THIS PRODUCT.
IF THIS PRODUCT IS NOT USED CORRECTLY, UNEXPECTED INJURY MAY
BE CAUSED TO USERS OR BYSTANDERS.
Also, store this manual in a convenient and safe place so that it can be easily
referred to during use of this product.
While all efforts have been made to ensure the accuracy of all information in this
manual, PFU assumes no liability to any party for any damage caused by errors or
omissions or by statements of any kind in this manual, its updates or supplements,
whether such errors are omissions or statements resulting from negligence,
accidents, or any other cause. PFU further assumes no liability arising from the
application or use of any product or system described herein; nor any liability for
incidental or consequential damages arising from the use of this manual. PFU
disclaims all warranties regarding the information contained herein, whether
expressed, implied, or statutory.
●ix
■ Preface
Safety Precautions
This manual describes important details for ensuring the safe and correct use of
this product. Thoroughly read this manual before you start to use this product. In
particular, be sure to read and fully understand the Safety Precautions described in
this manual before you use this product.
Warning Indications Used In This Manual
This manual uses the following indications to ensure safe and correct use of this
product, and to prevent possible danger and injury to the Operator and other
persons.
WARNING
CAUTION
●x
This indication alerts operators to an operation that, if not
strictly observed, may result in severe injury or death.
This indication alerts operators to an operation that, if not
strictly observed, may result in safety hazards to personnel or
damage to equipment.
Symbols Used In This Manual
This manual uses the following symbols in explanations in addition to warning
indications.
ATTENTION
This symbol alerts operators to particularly important information. Be sure to read this information.
This symbol alerts operators to helpful advice regarding operation.
HINT
A TRIANGLE symbol indicates that special care and attention
is required.
The drawing inside the triangle shows the specific caution.
A CIRCLE with a diagonal line inside shows action which users
may not perform.
The drawing inside or under the circle shows the specific action
that is not allowed.
R
Outline characters on a colored background show instructions
users should follow.
It may also include the drawing that shows the specific
instruction.
●xi
Screen Examples In This Manual
The screen examples in this manual are subject to change without notice in the
interest of product improvement.
If the actual displayed screen differs from the screen examples in this manual,
operate by following the actual displayed screen while referring to the User's
Manual of the scanner application you are using.
Furthermore, the screenshots in this manual are for the FUJITSU TWAIN32
scanner driver, ScandAll 21 Image Capturing Utility Software, FUJITSU ISIS
scanner driver, QuickScanTM image capturing software and Adobe® Acrobat®.
About Maintenance
The user must not perform repairs on this scanner. Contact the store where you
purchased the scanner or an authorized FUJITSU Image Scanner service provider
to make repairs to this product.
●xii
■ Safety Precautions
WARNING
The following describes important warnings described in this manual.
Do not touch the Power cable with wet hands.
Do not touch the power plug with wet hands. Doing so might cause electric
shock.
Do not damage the Power cable.
A damaged Power cable might cause fire or electric shock.
Do not place heavy objects on Power cables, or pull, bend, twist, heat,
damage or modify AC cables.
Also, do not use damaged AC cables or power plugs, and AC cables or
power plugs when the power outlet fitting is loose.
Use only specified AC cables and connector cables
Use only specified AC cables and connector cables. Failure to use the
correct cables might cause electric shock and equipment failure.
●xiii
Use this scanner only at the indicated power voltage. Do not connect
to multiple-power strips.
Use this scanner only at the indicated power voltage and current.
Improper power voltage and current might cause fire or electric shock.
Also, do not connect to multiple-power strips.
Wipe any dust from the power plug.
Wipe off any dust from metal parts on the power plug or metal fittings with
a soft, dry cloth. Accumulated dust might cause fire or electric shock.
Do not install the device in locations subject to oil smoke, steam,
humidity, and dust.
Do not install the scanner in locations subject to oil smoke, steam,
humidity, and dust. Doing so might cause fire or electric shock.
Do not use the scanner if you smell a strange odor coming from the
scanner.
If you detect heat coming from the device or detect other problems such
as smoke, strange smells or noises, immediately turn off the scanner and
disconnect its power plug.
Make sure that the smoking has stopped, and then contact the store
where you purchased the scanner or an authorized FUJITSU scanner
service provider.
●xiv
Turn the scanner OFF if it is damaged.
If the scanner is damaged for any reason, turn off the scanner and unplug
the power cable before contacting the store where you purchased the
scanner.
Do not put liquids inside the scanner.
Do not insert or drop metal objects into the scanner. Do not scan wet
documents or documents with paper clips or staples. Do not splash or
allow the scanner to get wet.
If foreign objects (water, small metal objects, liquids, etc.) get inside the
scanner, immediately turn off the scanner and disconnect the power plug
from the power outlet, contact the store where you purchased the scanner
or the Maintenance Service Center. Pay particular attention to this warning in households where there are small children.
Do not touch the inside of the scanner.
Do not take apart or modify the scanner. The inside of the scanner
contains high-voltage components. Touching these components might
cause fire or electric shock.
CAUTION
The following describes important cautions described in this manual.
●xv
Do not install the scanner on unstable surfaces.
Install the scanner on a desk so that none of its parts protrude outside of
the desktop. Also, make sure that the scanner is installed on a flat, level
surface.
Do not install the scanner on unstable surfaces. Install the scanner on a
level surface that is free of vibration to prevent it from tilting.
Install the scanner on a strong surface that will support the weight of the
scanner and any other devices on that surface.
Firmly insert the power plug.
Firmly insert the power plug into the power outlet as far it will go.
●xvi
Do not block the ventilation ports.
Do not block the ventilation ports. Blocking the ventilation ports generates
heat inside the scanner, which may result in fire or scanner failure.
Do not place heavy objects or stand on top of the scanner.
Do not place heavy objects on the scanner or use the scanner's top
surface for performing other work. Improper use may cause injuries.
Before moving the scanner, disconnect the power plug from the power
outlet.
Do not move the scanner with the power and interface cables connected
as this might damage the cables, causing fire, electric shock or injuries.
Before moving the scanner, be sure to disconnect the power plug from the
power outlet, and disconnect connector cables. Also, make sure that the
floor is free of obstructions.
Protect the scanner from static electricity.
Install the scanner away from strong magnetic fields and other sources of
interference. Also, protect the scanner from static electricity as this might
cause the scanner to malfunction.
●xvii
Do not use aerosol sprays near the scanner.
Do not use aerosol sprays to clean the scanner. Aerosol sprays cause dirt
and dust to enter the scanner, resulting in scanner failure and malfunction.
Avoid any contact when the scanner is in use.
Avoid touching any part of the scanner mechanism or paper when
scanning as this may cause injuries.
Disconnect the power plug from the power outlet when the scanner is
not used for a long period of time.
When the scanner is not used for a long period of time, be sure to
disconnect the power plug from the power outlet for safety.
Do not install the scanner in the direct sunlight.
Do not install the scanner in the direct sunlight or near heating apparatus.
Doing so might cause excessive heat to build up inside the scanner,
causing fire or scanner trouble. Install the scanner in a well-ventilated
location.
●xviii
Do not try to lift or move the scanner alone.
This scanner is heavy (99lbs/45kg). When you carry the scanner, ensure
that additional personnel are used.
●xix
■ FUJITSU Group Offices
Please send your comments on this manual or on FUJITSU products to the
following addresses:
●xx
FUJITSU COMPUTER PRODUCTS OF
AMERICA, INC.
2904 Orchard Parkway, San Jose, CA
95134-2009, U.S.A.
Phone: (1-800)432-6333;
Technical Assistance Center
(1-800)626-4686
Fax: (1-408)570-4046
Website: http://www.fcpa.com/
E-mail: info@fcpa.fujitsu.com
FUJITSU CANADA, INC.
6975 Creditview Road Unit 1
Mississauga, On L5N 8E9 Canada
Phone: (1-905)286-9666
Fax: (1-905)286-5997
Website: http://www.fujitsu.ca/
E-mail: imaging@fujitsu.ca
(For Sales Questions)
scantech@fujitsu.ca
(For technical questions)
FUJITSU EUROPE LTD.
Hayes Park Central, Hayes End Road,
Hayes Middlesex UB4 8FE, U.K.
Phone: (44-208)573-4444
Fax: (44-208)573-2643
Website: http://www.fel.fujitsu.com/
FUJITSU DEUTSCHLAND GmbH.
Frankfurter Ring 211, 80807 München,
Germany
Phone: (49-89)323-78-0
Fax: (49-89)323-78-100
Website: http://www.fdg.fujitsu.com/
E-mail: hotline_scanner@fdg.fujitsu.com
FUJITSU ITALIA S.p.A.
Via Nazario Sauro, 38
20099 Sesto San Giovanni (Milan), Italy
Phone: (39-02)26294-1
Fax: (39-02)26294-201
Website: http://www.fis.fujitsu.com/
E-mail: mbarondi@fis.fujitsu.com
FUJITSU ESPAÑA, S.A.
Camino Cerro de los Gamos, 1 28224,
Pozuelo de Alarcon, Madrid, Spain
Phone: (34-91)784-9000
Fax: (34-91)784-9379
Website: http://es.fujitsu.com/
E-mail: info@mail.fujitsu.es
FUJITSU AUSTRALIA LTD.
Fujitsu House 2 Julius Avenue
North Ryde, N.S.W 2113 Australia
Phone: (61-2)9776-4555
Fax: (61-2)9776-4024
Website: http://au.fujitsu.com/
FUJITSU ASIA PTE.LTD.
20 Science Park Road, #03-01, Tele
Teck Park Singapore Science Park II,
Singapore 117674
Phone: (65)777-6577
Fax: (65)771-5499
Website: http://sg.fujitsu.com/
E-mail: sales@sg.fujitsu.com
FUJITSU TAIWAN LTD.
19th Fl., No39, Sec.1,Chung-hwa Rd.,
Taipei, Taiwan
Phone: (886-2)2311-2255
Fax: (886-2)2311-2277
Website: http://tw.fujitsu.com/
FUJITSU HONG KONG LTD.
10/F., Lincoln House, 979 King's Road,
Taikoo Place, Island East, Hong Kong
Phone: (852)2827-5780
Fax: (852)2827-4724
Website: http://hk.fujitsu.com/
E-mail: scanner@fujitsu.com.hk
FUJITSU SYSTEMS BUSINESS
(THAILAND) LTD.
12th Fl., Olympia Thai Tower, 444
Rachadapisek Road, Samsennok,
Huay kwang, Bangkok 10310, Thailand
Phone: (662)512-6066
Fax: (662)512-6068
Website: http://th.fujitsu.com/
FUJITSU KOREA LTD.
Susong Tower Building, 83-1
Susong-Dong, Jongno-Gu, Seoul,
Republic of Korea
Phone: (82-2)3787-6159
Fax: (82-2)3787-6164
Website: http://kr.fujitsu.com/
E-mail: webmaster@fkl.fujitsu.co.kr
FUJITSU MALAYSIA SDN.BHD.
Level 1, 3505 Jalan Teknokrat 5, 63000
Cyberjaya, Malaysia
Phone: (60-3)8318-3700
Fax: (60-3)8318-8700
Website: http://my.fujitsu.com/
FUJITSU PHILIPPINES, INC
2nd Fl., United Life Building, 837
A.Arnaiz Avenue (Pasay Road), Legaspi
Village Makati City 1229, Philippines
Phone: (63-2)812-4001
Fax: (63-2)817-7576
Imaging Products Division,
PFU LIMITED
Solid Square East Tower, 580 Horikawacho, Saiwai-ku, Kawasaki-shi,
Kanagawa 212-8563, Japan
Phone: (81-44)540-4658
Fax: (81-44)540-4639
Website:
http://imagescanner.fujitsu.com/
E-mail: scanners@pfu.fujitsu.com
PFU LIMITED
(Corporate headquarters)
Nu 98-2 Unoke, Unoke-machi,
Kahoku-gun, Ishikawa 929-1192, Japan
Phone: (81-76)283-1212
Fax: (81-76)283-4689
●xxi
●xxii
CONTENTS
INTRODUCTION ....................................................................... i
Regulatory Information ........................................................ iii
Note, Liability ....................................................................... ix
Preface ................................................................................. x
Safety Precautions............................................................. xiii
FUJITSU Group Offices...................................................... xx
1 BASIC SCANNER OPERATIONS ............ 1-1
Turning the Scanner ON ................................................... 1-2
Waking up the Scanner from the Power Save Mode ........ 1-5
Basic Operations of the Operator Panel ........................... 1-6
Setting up the Hopper ..................................................... 1-14
Setting up the Stacker .................................................... 1-15
Setting the Stacker Extension ......................................... 1-17
Loading Documents on the Hopper ................................ 1-18
Inserting Documents Manually ....................................... 1-21
Scanning Documents ...................................................... 1-23
How to use the Scanner Driver ....................................... 1-27
2 SCANNING VARIOUS TYPES OF
DOCUMENTS2-1
Scanning Documents with different widths ....................... 2-2
Saving Scanned Images in PDF Format .......................... 2-3
Selecting a Color to drop out .......................................... 2-13
Skipping blank Pages ..................................................... 2-15
Detecting Double-Feeds ................................................. 2-17
Correcting skewed Documents ....................................... 2-19
3 DAILY CARE............................................. 3-1
Cleaning Materials and Areas Requiring Cleaning ........... 3-2
Cleaning the Pad .............................................................. 3-5
Cleaning the Rollers ......................................................... 3-8
Cleaning the Transport Path ........................................... 3-22
Cleaning the Discharge Brush ........................................ 3-24
Cleaning the Glass Surface ............................................ 3-29
Cleaning the Sensors ..................................................... 3-35
Cleaning the Lamps ........................................................ 3-41
●xxiii
4 REPLACEMENT OF CONSUMABLES .... 4-1
Consumables and Replacement Cycle ............................. 4-2
How to check the Abrasion Counter ................................. 4-3
Replacing the Pad ASSY .................................................. 4-4
Replacing the Pick Roller Unit .......................................... 4-9
Replacing the Brake Roller Unit ...................................... 4-12
Replacing the Front-side Lamp ....................................... 4-15
Replacing the Back-side Lamp ....................................... 4-20
5 SOLVING COMMON PROBLEMS ........... 5-1
Clearing Document Jams ................................................. 5-2
Troubleshooting ................................................................ 5-8
Before Contacting a Service Provider ............................. 5-30
Labels on the Scanner .................................................... 5-32
6 ADF DOCUMENT SPECIFICATIONS ...... 6-1
Document Size ................................................................. 6-2
Document Quality ............................................................. 6-3
Hole-punching Prohibited Areas ....................................... 6-6
Print Prohibited Area ......................................................... 6-7
Background Color Areas ................................................... 6-8
Job Separation Sheet ....................................................... 6-9
Hopper Capacity ............................................................. 6-10
7 OPERATOR PANEL MENUS ................... 7-1
Setup Mode ...................................................................... 7-2
Setup mode functions ..................................................... 7-10
Setup Mode Details ........................................................ 7-17
Test Mode Overview ...................................................... 7-64
Test Mode Details ........................................................... 7-70
8 OPTIONS .................................................. 8-1
Options ............................................................................. 8-2
fi-486PRFR (Front side imprinter) ..................................... 8-3
fi-486PRRE (Rear side imprinter) ..................................... 8-4
fi-486TRK (Thinner paper Roller Kit) ............................... 8-5
●xxiv
9 SCANNER SPECIFICATIONS.................. 9-1
Basic Product Specifications ............................................ 9-2
Installation Specifications ................................................. 9-3
Dimensions ....................................................................... 9-5
APPENDIX1
DROP-OUT COLOR ..........................................AP-1
APPENDIX2
DOUBLE-FEED DETECTION CONDITIONS ....AP-2
APPENDIX3
MESSAGES OF OPERATOR PANEL...............AP-5
INDEX
............................................................................IN-1
●xxv
●xxvi
1
BASIC SCANNER
OPERATIONS
This chapter describes basic scanner operations.
This chapter explains operations using the screens of Windows XP.
Depending on your OS, your PC's screen shots and the operation may be
different from this manual. Please be aware that when the FUJITSU TWAIN
32 scanner driver, or the FUJITSU ISIS scanner driver is updated, the
screens and operations noted in this chapter may be changed slightly. In this
case, please refer to the User's Guide provided with the update.
1.1 Turning the Scanner ON ....................................................1-2
1.2 Waking up the Scanner from the Power Save Mode .......1-5
1.3 Basic Operations of the Operator Panel ..........................1-6
1.4 Setting up the Hopper ......................................................1-14
1.5 Setting up the Stacker......................................................1-15
1.6 Setting the Stacker Extension .........................................1-17
1.7 Loading Documents on the Hopper................................1-18
1.8 Inserting Documents Manually .......................................1-21
1.9 Scanning Documents.......................................................1-23
1.10 How to use the Scanner Driver .....................................1-27
1-1
1.1 Turning the Scanner ON
■ Turning the power on
1.
Press "I" side of the main line switch located on the back of the scanner.
Power On
Main line
switch
(Rear View)
1-2
1.1 Turning the Scanner ON
2.
Press the power button on the Operator panel.
The power turns on and the green Power LED at the Operator panel lights.
Operator panel LCD shows "Ready" to indicate the scanner is in the READY
state.
1
Power Button
BASIC SCANNER OPERATIONS
1.1 Turning the Scanner ON
1-3
■ Turning the Power off
1.
On the Operator panel, press and hold down the Power button for two
seconds or longer.
2.
Press "O" side of the main line switch located on the back of the scanner.
Power Off
Main line
switch
(Rear View)
1-4
1.1 Turning the Scanner ON
1.2 Waking up the Scanner from the
Power Save Mode
The Power Save Mode keeps the scanner in a low powered state.
If no operation is performed on the scanner for a preset time (15 minutes to 60 minutes depending
on the timer setup), the scanner automatically switches to the Power Save Mode.
In the Power Save Mode, the Operator panel LCD display goes out while the green LED stays lit.
To wake up the scanner from the Power Save Mode, perform one of the following:
1
1.2 Waking up the Scanner from the Power Save Mode
BASIC SCANNER OPERATIONS
- Load documents on the hopper
- Press a button, except Power button, on the Operator panel
- Send a command from the PC
1-5
1.3 Basic Operations of the Operator
Panel
This basic operation include how to enter setup mode and test mode.
■ Clearing error messages
When an user recoverable error occurs, Check LED blinks to warn you and the
error message is displayed on the LCD. Here is an example of an error
message.
D
Press
ATTENTION
1-6
o
u
b
l
e
F
e
e
d
button to clear the blinking after the cause of the error is removed.
If you cannot clear errors with Check LED lit. They are not user recoverable
errors.
Refer to "Error mesage (Temporary error :Check LED blinking)" on page AP9 for the messages.
1.3 Basic Operations of the Operator Panel
■ Lifting or lowering the hopper
When the scanner has no errors (Check LED is not lit), the Hopper height position can be
changed.
CAUTION
1
During hopper height adjustment, do not put your hands or anything on or
under the hopper to prevent your fingers from getting caught and injured.
If something is caught in the mechanism, the scanner may be damaged.
BASIC SCANNER OPERATIONS
The Hopper height adjustment function is not available when:
-
Read LED is lit
A scanning operation is in progress
The scanner is in test mode (excluding Single feed and Multi feed)
The scanner is in setup mode
(1) In normal mode (i.e. not in test mode nor in setup mode), the Hopper height
changes as follows by pressing
(Exit button) for more than two seconds:
1.
When the Hopper is at the bottom position, it moves up to 250 sheet position.
2.
When the Hopper is at 250 sheet position, it moves down to the bottom
position.
3.
When the Hopper is at the highest position, it moves back to where it was when
the scan operation started.
The Hopper is positioned at the bottom when the power is turned on.
HINT
1.3 Basic Operations of the Operator Panel
1-7
(2) In test mode ([Single feed] or [Multi feed], the Hopper height changes as
follows by pressing
(Next button):
1.
When the Hopper is at the bottom position, it moves up to 250 sheet position.
2.
When the Hopper is at 250 sheet position, it moves down to the bottom
position.
3.
When the Hopper is at the highest position, it moves back to where it was when
the scan operation started.
ATTENTION
Pressing
(Previous button) does not change the position.
The Hopper is positioned at the bottom when the power is turned on.
HINT
1-8
1.3 Basic Operations of the Operator Panel
■ Clearing the consumables replacement message
This scanner has Abrasion counters to estimate service life of the consumables. When a counter
(for the Pad ASSY, the Pick roller unit, the Brake roller unit, the Front-side lamp or the Back-side
lamp) reaches the pre-set value, the LCD shows a message that the consumable’s service life has
expired. Here is an example of the error messages.
A
b
r
a
s
i
o
n
a
l
a
r
1
m
Keep pressing
BASIC SCANNER OPERATIONS
Enter setup mode. (For the details on how to enter the setup mode, refer to "7 OPERATOR
PANEL MENUS" on page 7-1.
(Next button) until the LCD shows the following message.
!
P
0
i
9
c
k
A
/
b
B
r
r
a
a
s
k
i
e
o
/
n
P
a
C
d
N
T
At this screen, you can select a consumable counter to reset. For the details on how to clear
consumable counter, please refer to the section "7 Setup Mode Details" on page 7-17.
1.3 Basic Operations of the Operator Panel
1-9
■ Using the setup and the test modes.
This scanner has the setup mode for customizing the setup conditions, and a test mode for testing
the scanner offline.
There are two types of setup modes: The Online setup mode that can be entered during Ready
status and the Offline setup mode that can be entered only when the scanner is offline. Available
functions are different depending on the mode. For the details, refer to "7 OPERATOR PANEL
MENUS" on page 7-1.
To enter these modes, follow the instructions below:
- Online setup mode
When the LCD indicates Ready status, press
appears.
M
!
Pressing
1-10
o
S
d
e
(Next button). The following message
e
t
u
S
p
e
l
M
e
o
c
d
t
e
(Enter button), the scanner enters the Online setup mode.
1.3 Basic Operations of the Operator Panel
1
Turning on the power
J
J
J
F
F
F
F
e
r
c
m
t
i
i
n
n
g
g
-
p
p
a
u
C h
W a
e
r
c
m
k
i
i
n
n
g
g
-
s
p
e
u
R e
W a
s
r
e
m
t
i
t
n
i
g
n
-
g
u
W a
i
t
i
n
g
I
e
a
d
y
R
M
!
p
N
e
o
r
w
!
!
n
N
s
o
o
w
r
!
!
p
o
N
p
o
p
w
e
!
r
!
F
R
e
a
d
y
x
x
x
x
x
x
x
x
x
x
h
x
Press
Press
(Next button)
(Previous button)
o
S
d
e
e
t
u
S
p
e
l
M
e
o
c
d
t
e
1
Setup (Online)
1.3 Basic Operations of the Operator Panel 1-11
1
BASIC SCANNER OPERATIONS
E j
W a
- Offline setup mode and test mode
Keep pressing
(Start button) and turn on the power.
Turn on the power while pressing the Start button
J
J
J
F
F
F
T
E
S
T
F
E j
W a
e
r
c
m
t
i
p
g
a
-
p
u
e
p
r
n
C h
W a
e
r
c
m
k
i
s
g
e
-
n
u
s
p
o
n
s
r
e
m
t
i
n
h
g
o
-
p
u
p
p
e
W a
M
S
O
E
D
T
E
U
S
E
P
L
T
E
E
<
N
n
o
o
w
w
:
T
r
N
o
n
w
o
:
w
T
r
N
o
n
w
o
:
w
T
C
S
T
T
>
Setup (Offline)
- To enter the setup mode, press
(Left arrow button) or
in [<Mode select>] screen to select [Setup] then press
To exit this mode, turn off the power.
1-12
1.3 Basic Operations of the Operator Panel
(Right arrow button)
(Enter button).
- To enter the test mode, from the [<Mode select>] screen, press
button) or
(Right arrow button) , select [Test] and press
Please see the Operator panel transition chart below.
<
<
M
S
O
E
D
T
E
U
P
<
T
E
S
T
S
L
T
E
E
C
S
T
T
>
M
O
D
E
>
>
(Start button) or
(Enter button).
1
(Enter button).
Test mode
To exit this mode, turn off the power.
1.3 Basic Operations of the Operator Panel 1-13
BASIC SCANNER OPERATIONS
Press
E
(Left arrow
1.4 Setting up the Hopper
1.
Gently flip down the Hopper table with holding its blue part.
1
BASIC SCANNER OPERATIONS
1.4 Setting up the Hopper 1-14
1.5 Setting up the Stacker
1.
Open the stacker.
Stacker
1
BASIC SCANNER OPERATIONS
1.5 Setting up the Stacker 1-15
2.
Push the opened stacker table lock into the scanner to lock it in place.
HINT
1-16
When closing the stacker, pull out the stacker a little then fold it
closed.
1.5 Setting up the Stacker
1.6 Setting the Stacker Extension
1.
Hold the center of the blue part of the stacker extension to pull it out.
Stopper
1
ATTENTION
Do not use the stopper to pull out the stacker extension.
Stopper may be damaged if you pull it.
1.6 Setting the Stacker Extension 1-17
BASIC SCANNER OPERATIONS
Stacker extension
1.7 Loading Documents on the Hopper
1.
Straighten the edges of the documents
1) Straighten both sides of the document stack.
2.
Fan the documents
1) Take a stack of documents with thickness of 15mm to 20mm (1/2 to 3/4
inch).
2) Hold both ends and bend the documents into an arch.
15 to 20mm
3) Firmly holding the document with both hands, bend back the document as
follows so that the bent section rises up in the middle of the document as
follows.
4) Repeat steps 1) to 3) for a few times.
5) Rotate the document 90 degrees, and fan again.
1-18
1.7 Loading Documents on the Hopper
3.
Load the documents on the hopper.
Place the documents face-up on the hopper table.
1
Hopper
Adjust the Side guides to the document width.
Pressing the lock lever, slide the Side guides so that they contact the document
sides.
If there is space between the document edges and the guides, the scanned
image may be skewed.
Side Guide
1.7 Loading Documents on the Hopper 1-19
BASIC SCANNER OPERATIONS
4.
ATTENTION
• Make sure that the document stack is below the maximum height mark
on the inside of the Side guides.
• For loading long documents, extend the hopper extension.
Hopper Extension
• A batch which consists of different sizes may cause feeding problems.
5.
Start up the scanner application and scan the documents.
For the details on how to scan using ScandAll 21, refer to the section "1.9
Scanning Documents" on page 1-23.
1-20
1.7 Loading Documents on the Hopper
1.8 Inserting Documents Manually
When the scanner is in Manual Feed Mode, set the documents as follows.
1.
Lift the Pick roller until it is held by the magnet catch. The hopper table
moves up to the feeding position.
Magnet catch
CAUTION
Be careful not to get your fingers or anything caught in the mechanism
when the hopper table moves up.
1.8 Inserting Documents Manually 1-21
BASIC SCANNER OPERATIONS
Pick roller unit
1
2.
Place documents face-up at the center of the hopper table.
HINT
3.
For information on setting Manual feed timeout, refer to "7 OPERATOR
PANEL MENUS" on page 7-1.
Adjust the Side guides to the width of the documents. Load the
documents so that the top edge of the documents contacts the hopper
table guide plate.
Hopper
1-22
1.8 Inserting Documents Manually
1.9 Scanning Documents
The following shows the procedure for scanning documents using the "ScandAll 21" application
(simply called "ScandAll 21" from now on.)
1.
Load the documents on the hopper.
For details on how to load documents, refer to the section "1 Loading
Documents on the Hopper" on page 1-18.
Adjust the stacker table to the document size.
ATTENTION
• For loading long documents on the hopper, extend the stacker
extension.
• For loading short documents on the hopper, adjust the stopper length.
3.
Start up ScandAll 21
From [Start] menu, select [Program] - [Scanner Utility for Microsoft Windows] [ScandAll 21]. This starts up ScandAll 21.
4.
Select the scanner to use
Select [Select Source] from the [Scan] menu.
1.9 Scanning Documents 1-23
BASIC SCANNER OPERATIONS
2.
1
The [Select source] dialog box appears.
Select [FUJITSU fi-4860CEAdij] (for TWAIN32 V8, [FUJITSU TWAIN 32]).
Then click [Select].
5.
Click the [Display in scan preview screen] on the tool bar.
The [TWAINDriver] dialog box (screen for setting scanning conditions)
appears.
1-24
1.9 Scanning Documents
6.
Set the scan resolution, document size and other scan conditions, and
click the [Scan] button.
For the details on settings in the [TWAIN Driver] dialog box, refer to the
"Scanner Utility for Microsoft® Windows® User's Guide" on the scanner driver
CD-ROM.
1
BASIC SCANNER OPERATIONS
1.9 Scanning Documents 1-25
The image of the scanned document appears on the ScandAll 21 screen.
For details on scanning various types of documents, refer to "2 SCANNING
VARIOUS TYPES OF DOCUMENTS" on page 2-1.
For details on ScandAll 21 function and operations, refer to ScandAll 21 Help.
1-26
1.9 Scanning Documents
1.10 How to use the Scanner Driver
■ FUJITSU TWAIN32 Scanner Driver
FUJITSU TWAIN32 Scanner Driver is designed for scanning documents with FUJITSU image
scanner fi series by using application software that complies with the TWAIN standard.
The following describes the procedure with examples of ScandAll 21 for ordinary scanning by
using this driver software.
1.
Startup the application.
From the [Start] menu, select [Programs]-[Scanner Utility for Microsoft Window]
and click [ScandAll 21].
2.
Select your scanner on the window below.
Select [Select Source] from the [Scan] menu.
1.10 How to use the Scanner Driver 1-27
BASIC SCANNER OPERATIONS
● Procedure for Basic Scanning Operation
1
3.
Select the scanner to use, then click the [Select] button.
Select
• [FUJITSU
fi-4860CEAdij] for FUJITSU TWAIN32 V9
or
• [FUJITSU
TWAIN32] for FUJITSU TWAIN32 V8
then click the [Select] button.
4.
Load the documents on the scanner.
For details on loading documents, refer to "1.7 Loading Documents on the
Hopper" on page 1-18.
5.
Open the TWAIN Driver window.
Select [Scan To View] from the [Scan] menu.
•ScandAll
•[To
21 provides scanning methods as follows:
View...] :Displays scanned images on the window.
•[To
File...:] :Saves scanned images as files (*.BMP, *.TIF, *.JPG) on your hard
disk.
•[To
FTP...:] :Transfers scanned images to a FTP server.
•[To
Adobe PDF...:] :Saves scanned images as PDF files.
•(*Adobe
Acrobat must be installed beforehand.)
•[To
Microsoft Share Point Portal Server...] :Transfers scanned images to
Microsoft Share Point Portal Server.
1-28
•[To
Mail...] :Launches mailer software and attaches scanned images to e-mail.
•For
details, refer to "ScandAll 21 Help".
1.10 How to use the Scanner Driver
6.
Configure settings for scanning and click the [Scan] button.
1
1.10 How to use the Scanner Driver 1-29
BASIC SCANNER OPERATIONS
For details about the settings on this window, refer to "Setting Window for
FUJITSU TWAIN32 Scanner Driver." on page 1-31.
⇒ The
images of scanned documents are displayed on the [ScandAll 21] window.
Depending on the settings of the application software, images may not be
displayed.
For details, refer to the documentation or Help file of your application.
e.x.) When you select [To File...] from the [Scan] menu of ScandAll 21,
images of scanned documents are not displayed on the window.
7.
Save the scanned images.
Select [Save As...] from the [File] menu to save the scanned images.
If you wish to start another scanning, return to procedure 4.
8.
End the application.
Select [Exit] from the [File] menu.
1-30
1.10 How to use the Scanner Driver
● Setting Window for FUJITSU TWAIN32 Scanner Driver.
1
•
For details on each functions, refer to "FUJITSU TWAIN32 Scanner
Driver Help" (appears by pressing [Help] or [F1] button).
•
Depending on the type of your scanner, available setting items or range
of setting values vary.
Resolution
Specifies the resolution of scanning.
It can be specified by selecting a default value from the list or customizing.
By marking the [Predefine] checkbox, you can select one from three predefined settings
as [Normal], [Fine], [Super Fine] to scan documents instead of setting details by
yourself.
Otherwise, you can change the details of the predefined settings on the [Resolution
Setting] window, which appears when you click on the [...] button.
Scan Type
Specifies the feeding method, the side(s) to be scanned (Front Side, Back Side,
Duplex) or details of Long page (the size of documents longer than Ledger/A3).
1.10 How to use the Scanner Driver 1-31
BASIC SCANNER OPERATIONS
You can perform settings for the FUJITSU TWAIN32 Scanner Driver on
this window.
The following describes the main setting items.
Paper Size
Select the size of documents to be scanned from this list.
Windows for customizing the paper size will appear when you click on [...] besides the
list. You can save any document size as a customized setting (up to three) or for
changing the order of the paper size in the list.
Image Mode
Specifies the image type for the scanned documents.
Black & White
Documents are scanned in binary (black and white).
Halftone
Documents are scanned with halftone processing in black
and white.
Grayscale
Documents are scanned with 256 gradations from black to
white.
Color
Documents are scanned in color. For this mode, you can
select 24 bit Color, 256Color or 8 Color.
[Scan] button
Starts scanning documents with the current settings.
[Preview] button
Documents are scanned preliminarily before the actual scanning.
You can confirm the image of the documents in the preview window.
[Close] button
Saves the current settings and closes this window.
[Reset] button
Used to undo changes of settings.
[Help] button
Opens the "FUJITSU TWAIN32 Scanner Driver Help" window. The window also opens
by pushing the [F1] key.
[About...] button
Opens an information window about the FUJITSU TWAIN32 Scanner Driver's version.
1-32
1.10 How to use the Scanner Driver
[Option...] button
You can set up the details of optional functions on the window below.
1
Select this tab when setting image rotation, detection of document size and skew, etc.
[Job/Cache] tab
Select this tab when setting cache mode, job controls, double-feed detection, blank
page skipping, etc.
[Generic] tab
Select this tab to change the unit displayed on the Setting Window for the FUJITSU
TWAIN32 Scanner Driver. (Millimeters, Inches, and Pixels are available)
[Filter] tab
Select this tab for setting the image processing filter(s).
Page Edge Filler: Fills up the margins of the scanned documents with a selected color.
[Compression] tab
Select this tab for setting the compression rate of JPEG Transfer.
[Advance...] button
Click this button for settings of the advanced image processing.
You can set Edge Extract, Gamma Pattern, White Level Follower, Dropout Color,
Reverse, etc.
[Config...] button
Click this button for configuring the Setting Files.
You can save the changed settings as a Setting File. From next scanning, the settings
are quickly changed by using these Setting Files.
For details of each function, refer to the "FUJITSU TWAIN32 Scsnner
Driver Help".
1.10 How to use the Scanner Driver 1-33
BASIC SCANNER OPERATIONS
[Rotation] tab
■ FUJITSU ISIS Scanner Driver
FUJITSU ISIS Scanner Driver is designed for scanning documents with FUJITSU image scanner
fi series by using application software that complies with the ISIS standard.
The following describes the procedure with examples of QuickScanTM for ordinary scanning by
using this driver software.
The procedure may vary depending on your application. If you use an application other than
QuickScanTM, please refer to its Guide or Help for further information.
● Procedure for Basic Scanning Operation
1.
Startup the application.
From the [Start] menu, select [Programs]-[QuickScan] and click [QuickScan].
2.
Select your scanner on the window below.
Select [Scan] - [Select Scanner] on the menu bar.
3.
1-34
Select fi-4860C, then click the [OK] button.
1.10 How to use the Scanner Driver
4.
Select [Scan] - [New Batch] on the menu bar.
5.
Select the profile for scanning.
1
creating a new profile
Select one from already existing profiles and click [Add Profile...] button.
⇒ A new profile will be created based on the profile you select.
•When
changing the settings of already existing profiles
Select one from already existing profiles and click [Edit Profile...] button.
⇒ The settings of the selected profile can be changed.
•When
deleting a profile
Select the one to delete and click [Delete] button.
⇒ The selected profile will be deleted.
When you added, edited or deleted a profile, go to the procedure 10.
1.10 How to use the Scanner Driver 1-35
BASIC SCANNER OPERATIONS
•When
6.
Open the window of ISIS Driver.
Select the [Scan] tab and click the [Scanner Settings] on the [Profile Editor]
window.
⇒ The
7.
configuration window of ISIS driver appears.
Configure settings for scanning and click the [OK] button.
For details on this dialog box, refer to "Configuration Window of FUJITSU ISIS
Scanner Driver" on page 1-38.
1-36
1.10 How to use the Scanner Driver
8.
The [Profile Editor] window appears. Click the [OK] button to return to
[New batch] dialog.
HINT
Configure other settings of the profile, if necessary.
Refer to the "QuickScan Overview" or the "QuickScan Help" for further
information on functions and operations of QuickScanTM. After the installation of QuickScan, it is registered in the [Start] menu.
9.
1
Load the documents on the scanner.
BASIC SCANNER OPERATIONS
10. Click the [Scan] button.
⇒ Scanned
images are displayed on the window.
Refer to the "QuickScan Overview" or the "QuickScan Help" for further
information on functions and operations of QuickScan. After the installation of
QuickScan, it is registered in the [Start] menu.
1.10 How to use the Scanner Driver 1-37
● Configuration Window of FUJITSU ISIS Scanner Driver
Image Mode
Select a color mode suitable for the purpose from the menu.
Black and White
256-level Gray
24-bit Color
Scans data in binary (black and white). Distinguishes black
from white according to the fixed threshold. This scanning
mode is suitable for scanning line drawings and text documents.
Scans data with 256 gradations from black to white. This
mode uses 8 bits per pixel. This mode is suitable for scanning monochrome photographs.
Scans data as full-color images using 24 bits per pixel. This
mode is suitable for scanning color photographs.
Dots per inch
Specifies the number of pixels (dots) per inch.
Select a fixed resolution from the list.
A higher resolution produces finer images, but requires much more memory.
Dither
Select the halftone pattern for halftone scanning. This setting is available when "Black
and White" is selected in the "Mode".
1-38
Dither Pattern 1
This setting is suitable for scanning dark photographs.
Dither Pattern 2
This setting is suitable for scanning dark-colored documents
containing both text and photographs.
Dither Pattern 3
This setting is suitable for scanning light photographs.
1.10 How to use the Scanner Driver
Dither Pattern 4
This setting is suitable for scanning light-colored documents
containing both text and photographs.
Error Diffusion
This function minimizes differences of color levels due to
subtractive color process by diffusing the difference to the
adjacent pixels. This mode is suitable for scanning images of
photographs, etc.
Brightness
Sets the brightness of the entire image. Specify the brightness as a number within the
range of 1 (dark) to 255 (bright). To brighten the entire image, increase the value of the
setting. To darken the entire image, decrease the value.
Sets the contrast between light and shadow of the scanned image. Specify the contrast
as a number within the range of 1 (low [soft]) to 255 (high [sharp]). Increasing this value
makes the contrast sharper.
Paper Source
Selects the scanning method.
Feeder
Duplex
Scans only one sides of documents specified with the scanner.
Scans both front and the back sides of documents. When this
option is selected, the both sides of documents are scanned
simultaneously.
Paper Size
Selects a paper size according to the size of the document to be scanned. Select a
standard paper size from the list.
Page Layout
Specifies orientation of the documents as portrait or landscape.
Auto Crop
Automatically detects the document’s page size, and the output will be adjusted to the
detected page size. Document skewing is automatically detected and corrected for the
output image. This function is availble when Black and White or 256-level Gray is
selected at the Image Mode.
[Side]
The settings of this window are applied to the selected document side (Both, Front,
Back).
[More...] button
Opens the [More Settings] window. Used for setting advanced features.
1.10 How to use the Scanner Driver 1-39
BASIC SCANNER OPERATIONS
Contrast
1
[Area...] button
Opens the [Scan Area] dialog box.
Specify scan area for the document size.
The size can be set by dragging the frame with mouse.
Otherwise, enter any value for the setting.
[Endorser...] button
This button displays [Endorser Configuration] dialog. This button is enabled when
Endorser Option (separately sold) is installed. Refer to the documentation provided with
the Endorser Option.
[JPEG...] button
1-40
1.10 How to use the Scanner Driver
Opens the JPEG Settings dialog box. Used for setting the compression rate of JPEG
transfer, etc.
1
This button displays the version information.
● Settings on the [Image Processing] window
You can configure optional funcitons on this window.
Gamma
Specifies Gamma correction. Available correction patterns are: "Normal", "Soft",
"Sharp".
Image Enhancement Options
You can set the binary image processing. These options are available only when “Black
and White” is selected in the “Mode”.
1.10 How to use the Scanner Driver 1-41
BASIC SCANNER OPERATIONS
[About...] button
Quick Set
You can select a preset pattern for image enhancement. By selecting the one from the
list, you can quickly set the details of the image enhancement processing. Available
patterns are as follows:
Normal documents
This item is suitable for scanning the documents like the ones
(default)
used in offices.
Background/Foreground This option makes image contours soft by disabling the OutEnhancement
line Extraction.
NCR forms with backgor- This option removes background of scanned images and
und removed
smoothes outline on the images.
Magazines, Brochures, This option is suitable for scanning documents which have
etc.
texts and photos (e.g. magazines, brochures).
Use Brightness Control Performs simple binary processing on the images. When this
option is selected, you can manually adjust the threshold
(Brightness) with the slider control on the Configuration Window.
Standard
Performs simple binary processing. You can select the brigthtness from minimum (0) to maximum (6).
Advanced
Performs automatic binary processing. For OCR, select an
option from 0 to 4. For images select 5 or 6.
Image Emphasis
This option specifies the sharpness of outline extraction. Available settings are as
follows.
Low, Mid, High
Smooth
Emphasizes contour of images.
Smoothes jaggy images.
Mirror Image
This option reverses right and left in images.
Reverse Image Format
This option reverses black and white colors in images.
Outline Extraction
This option extracts contours of images.
Automatic Separation
When this option is selected, photos are automatically distinguished from lines
(characters) at scanning and dither patterns are applied to the photos. This option is
suitable for scanning documents which have both characters and photos.
[Side]
The settings of this configuration window are applied to the selected document side
(Both, Front, Back).
White Level Follow
1-42
1.10 How to use the Scanner Driver
This option is used to adjust the density of the white background of documents and
correct variations in the background color by compensating the pixels of scanned
images individually.
Auto
On
Off
This option optimize the settings based on the specified
“Mode”.
This option scans documents using background follow-up (for
line drawings).
This option scans doucments using the standard basic white
background (for photographs).
● Settings on the [Extra Features] window
You can configure advanced features on this window.
Dropout Color
This option excludes a selected color (green, red, or blue) from scanned images. For
example, if the document contains black text in a red frame and when the red color is
selected, the scanner reads only the text and eliminates (drop out) the red frame.
1.10 How to use the Scanner Driver 1-43
1
BASIC SCANNER OPERATIONS
[Extra Features] button
This button opens [Extra Features] button. You can configure advanced
functions on this window.
Detect Page Length
Scans the edge (bottom) of the documents and outputs data adjusted to the document
length. When any page shorter than specified "Paper Size" is included, the output size
is adjusted to the detected short size.
Enable Sleep Timer
This option specifies waiting time for turning off the lamps. The lamps will be turned off
when no operation is performed on the scanner for a certain period of time defined with
this option.
Double Feed Detection
Detects Double-feeds (phenomena that two or more sheets are accidentally fed). You
can set conditions for detecting Double-feeds so that the scanner will stop its operation
and display error messages. Double feeds are scanned by the differences in document
lengths or thicknesses.
Skew
With this option, you can set the scanner so that it will stop its operation and display
error messages when any skewed document is detected.
Pre-pick
With this option, you can enable or disable Pre-picking. Pre-picking is an operation that
feeds documetns into the ADF (to the scannning position) before starting actual
scanning operation.
Overscan
This option specifies the overscan function. This function makes the scanned images
larger than the original documents by adding margins.
[Side]
The settings of this configuration window are applied to the selected document side
(Both, Front, Back).
1-44
1.10 How to use the Scanner Driver
2
SCANNING VARIOUS
TYPES OF DOCUMENTS
This chapter describes how to scan various types of documents.
This chapter explains operations using the screens of Windows XP.
Depending on your OS, your PC's screen shots and the operation may be
different from this manual. Please be aware that when the FUJITSU TWAIN
32 scanner driver or the FUJITSU ISIS scanner driver is updated, the screens
and operations noted in this chapter may change. In that case, please refer to
the User's Guide provided with the update.
2.1 Scanning Documents with different widths .....................2-2
2.2 Saving Scanned Images in PDF Format...........................2-3
2.3 Selecting a Color to drop out ..........................................2-13
2.4 Skipping blank Pages ......................................................2-15
2.5 Detecting Double-Feeds ..................................................2-17
2.6 Correcting skewed Documents.......................................2-19
2-1
2.1 Scanning Documents with different
widths
When you scan a batch of documents with different widths, you may get skewed images from
smaller sized documents.
Scanning documents of the same width is recommended.
The following shows the procedure to scan batches of mixed size documents.
1.
Sort the batch into the stacks of the same width documents.
2.
Adjust the side guide to the width of each document stack to scan.
For the explanation on how to scan the documents, please refer to the section "1.9 Scanning
Documents" on page 1-23.
2-2
2.1 Scanning Documents with different widths
2.2 Saving Scanned Images in PDF
Format
If you would like to save scanned images in PDF format, you must first install Adobe® Acrobat®
5.0 or later on your PC.
Adobe® Acrobat® 5.0 can be installed from the Adobe® Acrobat® CD-ROM provided.
There are 2 ways for saving scanned images in PDF format.
(2) Using Adobe Acrobat 5.0
This method is recommended for finishing the scan operation faster and/or for black
and white scanning.
The benefits are:
Quick Creation of PDF file with original scan resolution
Flexible creation of PDF files by changing the PDF compression rates
Grayscale or color scanning creates larger file sizes than black and white scanning.
If the file size is very large, you can reduce the file size by configuring the properties of Acrobat
Distiller before saving scanned images.
For details, please refer to the hints in this section.
2.2 Saving Scanned Images in PDF Format
2-3
2
SCANNING VARIOUS TYPES OF DOCUMENTS
(1) Using ScandAll 21
This method is recommended for color or grayscale scanning and when smaller PDF
file size is required.
The benefits are:
Reduced PDF data size
Simplified method for creating PDF files with no troublesome operations
Using ScandAll 21
Following shows the procedure for saving scanned images in PDF format.
1.
Load the documents on the hopper.
2.
Start up ScandAll 21.
Select [Program]-[Scanner Utility for Microsoft Windows]-[ScandAll21] from the
[Start] menu. This will start up the application.
3.
From the menu bar select [Scan] and then [To Adobe PDF] from the pull
down menu.
[TWAIN Driver] dialog is displayed.
2-4
2.2 Saving Scanned Images in PDF Format
4.
Select the scan resolution, document size and other scanning conditions,
and then click the [Scan] botton.
2
SCANNING VARIOUS TYPES OF DOCUMENTS
5.
To end scanning, click the [Close] button.
The window for saving the image appears.
2.2 Saving Scanned Images in PDF Format
2-5
6.
Save the scanned image by selecting file name and path.
For details, refer to ScandAll 21 Help.
Using Adobe Acrobat 5.0
Following shows the procedure for saving scanned images in PDF format.
1.
Load the documents on the hopper.
2.
Start up Adobe Acrobat 5.0.
Select [Program] - [Adobe Acrobat] from the [Start] menu. This starts up Adobe
Acrobat 5.0.
2-6
2.2 Saving Scanned Images in PDF Format
3.
From the [File] menu select [Import] - [Scan] in that order.
[Acrobat Scan Plugin] dialog box is displayed.
2
SCANNING VARIOUS TYPES OF DOCUMENTS
4.
Select [FUJITSU fi-4860CEAdij] (for WindowsNT 4.0, select [FUJITSU
TWAIN 32]) at [Device] and click [Scan] button.
[TWAIN driver] dialog box is displayed.
Select [Simplex] even if you intend to do duplex scanning.
ATTENTION
2.2 Saving Scanned Images in PDF Format
2-7
5.
Select the scan resolution, document size and other scan conditions, and
click the [Scan] button.
6. To end scanning, click the [Close] button.
The scanned image is displayed.
2-8
2.2 Saving Scanned Images in PDF Format
7. Select [Save as] or [Save] from [File] menu to save the scanned image.
2
2.2 Saving Scanned Images in PDF Format
2-9
SCANNING VARIOUS TYPES OF DOCUMENTS
For the details on Adobe Acrobat 5.0 operations, refer to the Adobe Acrobat 5.0
manual and Help.
HINT
If you save scanned documents by this procedure, the file size will be very
large. If you would like to reduce the file size, please follow the procedure
below. (It may take more time than usual)
1.Select [File (F)] - |[Print (P)...].
2. Following dialog is displayed, then specify [Acrobat Distiller] for [Print
Name].
2-10
2.2 Saving Scanned Images in PDF Format
3. Press the [Properties] button.
2
2.2 Saving Scanned Images in PDF Format 2-11
SCANNING VARIOUS TYPES OF DOCUMENTS
4, Press the [Adobe PDF settings] tab.
5. Select Conversion settings to [Print].
Press [Edit Conversion settings] to specify resolution.
Specify the resolution of your choice. (300dpi recommended.)
.
6. Click [OK] when finishing setup.
7. [Save as PDF File] dialog is displayed, then select the file name and click
on [Save] button.
2-12
2.2 Saving Scanned Images in PDF Format
2.3 Selecting a Color to drop out
A selected color (red, green, blue) can be removed (dropped out) from the scanned image data.
For example, if the document contains black text in green frames, you can set the scanner to get
only the text and eliminate the green frames.
To drop out a color, change the setting in the driver setting dialog box.
The following shows examples for changing the setting of [TWAIN Driver ] dialog box to drop
out a color.
Click [Advance] button in the [TWAIN Driver] dialog box.
The [Advance] dialog box appears.
2.3 Selecting a Color to drop out 2-13
SCANNING VARIOUS TYPES OF DOCUMENTS
1.
2
2.
Select the color to drop out from [Dropout Color] under [More].
For example, if the document contains black text in green frames, you can set
the scanner to get only the text and eliminate the green frames.
3.
Click [OK] button.
[TWAIN Driver] dialog box will be redisplayed.
Start scanning from this dialog box and you can drop out the color specified
above.
2-14
2.3 Selecting a Color to drop out
2.4 Skipping blank Pages
The following shows examples for changing settings in the [TWAIN Driver] dialogbox to skip blank pages
at scanning documents.
1.
Click the [Option ...] button in the [TWAIN Driver] dialogbox.
2
2.
SCANNING VARIOUS TYPES OF DOCUMENTS
⇒ The
[Option] dialogbox appears.
Click the [Job/Cache] tab
2.4 Skipping blank Pages 2-15
3.
Select [Ram Cache] from the [Cache Mode] menu under [Caching].
4.
By using the slider control under [Blank Page Skip], specify the [Black
Dots Ratio] or [White Dots Ratio] (ratio of black or white parts on the
documents) for judging if the scanned document is recognized as a blank
page by the scanner.
The [TWAIN Driver] dialogbox will be redisplayed. Then, perform the scanning operation on the
dialogbox.
2-16
2.4 Skipping blank Pages
2.5 Detecting Double-Feeds
"Double-feed" is an error that occurs when two or more sheets are accidentally fed into the ADF
at the same time. You can set the scanner to display an error message when it detects a doublefeed.
To set conditions for the double-feed detection, change the settings in the driver setting dialog
box. The following shows examples for changing the settings in the [TWAIN Driver] dialog box.
The following shows the procedure for changing the settings in the dialogbox.
1.
Click the [Option...] button in the [TWAIN Driver] dialogbox.
SCANNING VARIOUS TYPES OF DOCUMENTS
⇒ The
2.
2
[Option] dialogbox appears.
Click the [Job/Cache] tab.
2.5 Detecting Double-Feeds 2-17
3.
Select the detection conditions from [Double Feed Detection] under [ADF
Option].
The following are the detection conditions
None
Double-feed detection is not performed
Check
The scanner monitors for the overlapping of documents. It
overlapping
detects a double-feed by differences in document thickness
when two or more document sheets are fed overlapped.
Check length
The scanner monitors the length of documents. It detects a
double-feed by differences in the document length when two
or more document sheets are fed overlapping.
Check
The scanner monitors both document overlapping and
overlapping and length to detect double-feeds.
length
Furthermore, refer to "APPENDIX2 DOUBLE-FEED DETECTION
CONDITIONS" on page AP-2 for detailed information about the document for
double-feed detection.
4.
Click the [OK] button.
The display returns to the [TWAIN Driver] dialogbox. Then, perform the
scanning operation on the dialogbox.
2-18
2.5 Detecting Double-Feeds
2.6 Correcting skewed Documents
You can set the scanner so that skew of documents is detected and corrected automatically when
skewed documents are fed into the ADF.
The following shows examples for chaning the setting in the [TWAIN Driver] dialogbox to enable
this function.
The following shows the procedure for changing the setting in the dialogbox.
1.
Click the [Option...] button in the [TWAIN Driver] dialogbox.
2.
SCANNING VARIOUS TYPES OF DOCUMENTS
⇒
2
The dialogbox appears.
Click the [Rotation] tab.
2.6 Correcting skewed Documents 2-19
3.
Select the [Automatic Page Size Detection] from the [Automatic Size and
Skew Detection] menu.
4.
Click the [OK] button.
The display returns to the scanninig operation [TWAIN Driver] dialogbox.
Then, perform the scanning operation on the dialogbox.
ATTENTION
When using either of the following documents, the automatic page size
detection may not function correctly.
Paper of weight less than 52 g/m2.
Not rectangular documents.
Documents which their edges are filled.
2-20
2.6 Correcting skewed Documents
3
DAILY CARE
This chapter describes how to clean the scanner.
WARNING
When you clean the scanner, turn off
the power, and unplug the power
cable from the outlet.
3.1 Cleaning Materials and Areas Requiring Cleaning .........3-2
3.2 Cleaning the Pad ................................................................3-5
3.3 Cleaning the Rollers...........................................................3-8
3.4 Cleaning the Transport Path............................................3-22
3.5 Cleaning the Discharge Brush ........................................3-24
3.6 Cleaning the Glass Surface .............................................3-29
3.7 Cleaning the Sensors.......................................................3-35
3.8 Cleaning the Lamps .........................................................3-41
3-1
3.1 Cleaning Materials and Areas
Requiring Cleaning
■ Cleaning materials
Cleaning materials
Cleaning sheet
Part No.
CA99501-0016
Remarks
20 sheets/pack
(* 1)
Cleaner F2
CA99501-0014
1 bottle, 100ml/bottle
(* 1)
Isopropyl alcohol or
Cleaner F1
CA99501-0013
1 bottle, 100ml/bottle
Moisten cloth with this
fluid and wipe the scanner to clean.
(* 1)
Cotton swab
Commercially available one
Lint-free dry cloth
Commercially available one(* 2)
* 1) For the purchase of the cleaning material, contact the FUJITSU scanner dealer where
you purchased the scanner.
*2) Any lint-free cloth can be used.
3-2
3.1 Cleaning Materials and Areas Requiring Cleaning
■ Locations requiring Cleaning and Cleaning
Frequency
The following shows the standard cleaning frequency for each area requiring
cleaning.
Part to clean
3
Standard Cleaning Frequency
Clean every 100,000sheets
Pick roller
Clean every 100,000sheets
DAILY CARE
Pad
Brake roller
Separation roller
Feed roller
Pinch roller
Transport path
Clean every 200,000sheets
Discharge brush
Clean every 100,000sheets
Removable sheet guide
Clean every 200,000sheets
Glass sheet guide
Document width detection sensor
Clean every 200,000sheets
Ultra sonic sensor
SF0
SF1
SF1.5
SF2
Front-side Lamp
Clean every 100,000sheets
Back-side lamp
Please clean rollers using the cleaning sheet every 50,000 sheets.
ATTENTION
3.1 Cleaning Materials and Areas Requiring Cleaning
3-3
ATTENTION
The scanner must be cleaned more frequently if you scan any of the following types of sheets:
• Documents of coated paper
• Documents that are almost completely covered with printed text or
graphics
• Chemically treated documents such as carbonless paper
• Documents containing a large amount of calcium carbonate
• Documents filled in with pencil
ATTENTION
ATTENTION
Do not use aerosol sprays to clean the scanner. The air from the spray may
cause dirt and dust to enter the scanner mechanism and resulting scanner
failure or malfunction.
Vacuum the scanner instead.
You must clean the following area more frequently when you use fi486PRFR or fi-486PRRF imprinters. The imprinter ink tend to stick to the
document transport path.
• Removable sheet guide
• Glass sheet guide
• Feed rollers
• Pinch rollers
3-4
3.1 Cleaning Materials and Areas Requiring Cleaning
3.2 Cleaning the Pad
1.
Remove documents from the stacker. Pull up the lever on the right front
of the Upper transport and then raise it.
CAUTION
Raise the Upper transport unit fully, then lower it to engage lock before you
put your hands inside of the scanner.
3
DAILY CARE
2.
Pull the ADF release lever toward you and lift up the ADF upper sheet
guide.
ADF upper sheet guide
ADF release lever
3.2 Cleaning the Pad
3-5
3.
Press down on the upper part of the Guide plate with your fingers at the
two positions shown and then rotate the plate toward you to remove it.
Pad ASSY
Guide plate
3-6
3.2 Cleaning the Pad
4.
Wipe the translucent rubber part of the Pad ASSY using a lint free cloth
moistened with cleaner F1.
Pad (cleaning area)
3
Pad ASSY
DAILY CARE
Guide plate
5.
Install the guide plate in the reverse order of the removal.You should
push it down then rotate back, so the installation can be done smoothly.
6.
Lower the ADF upper sheet guide carefully.
7.
Lift the Upper transport unit to release the safety lock, then lower the unit
carefully and push the unit to close it completely.
3.2 Cleaning the Pad
3-7
3.3 Cleaning the Rollers
■ Cleaning the rollers with the cleaning sheet
1.
Set the Side guide for B4 size width.
2.
Set the scanner in Test mode: For the details of the procedure, refer to
the section "7.5 Test Mode Details" on page 7-70.
3.
Press
(Next button) to show the following screen.
T
0
2
M
u
l
t
i
f
e
e
d
4.
Remove the protective paper from the cleaning sheet.
5.
Place the cleaning sheet on the hopper table, align the left side with the
hopper guide and with the adhesive side up. Press
then the cleaning sheet is fed.
3-8
3.3 Cleaning the Rollers
(Start button),
6.
When [Hopper Empty] is displayed, press
(Stop button).
7.
Place the same cleaning sheet on the hopper table with adhesive side up
by aligning the right side with the hopper guide. Press
then the cleaning sheet is fed.
(Start button),
3
DAILY CARE
8.
When "Hopper Empty" is displayed, press
9.
Remove the protective paper from a new cleaning sheet and place it with
the adhesive side face down on the hopper table, aligning the left side
with the hopper guide. Press
is fed.
(Stop button).
(Start button), then the cleaning sheet
Repeat steps 6 through 8. When the cleaning is completed turn off the power.
3.3 Cleaning the Rollers
3-9
■ Cleaning the Pick Rollers and the Separation Roller
1.
Remove documents from the stacker. Pull up the lever on the right front
of the Upper transport and then raise it.
CAUTION
3-10
Raise the Upper transport unit fully, then lower it to engage lock before you
put your hands inside of the scanner.
3.3 Cleaning the Rollers
2.
While pulling the ADF lever toward you, lift up the ADF upper sheet guide.
ADF upper sheet guide
3
DAILY CARE
ADF release lever
3.
Slide the Pick roller unit to the left to disengage the clutch ring from the
shaft.
Pick roller unit
Ring
Shaft
3.3 Cleaning the Rollers 3-11
4.
Wipe both Pick rollers (2 positions) and the Separation roller using a
clean lint free cloth moistened with cleaner F1.
Ring
Separation roller
Pick roller unit
3-12
3.3 Cleaning the Rollers
5.
Install the Pick roller unit in the reverse order of its removal.
HINT
When attaching the Pick roller unit, hold the unit as
shown. Engage the drive ring onto the drive shaft.
Move left and align the clutch ring with the shaft and
move right to engage.
Incorrect installation
Correct installation
3
DAILY CARE
6.
Lower the ADF upper sheet guide carefully.
7.
Lift the Upper transport unit to release the safety lock, then lower the unit
carefully and push the unit to close it completely.
3.3 Cleaning the Rollers 3-13
■ Cleaning the Brake roller unit
1.
Remove documents from the stacker. Pull up the lever on the right front
of the Upper transport and then raise it.
CAUTION
3-14
Raise the Upper transport unit fully, then lower it to engage lock before you
put your hands inside of the scanner.
3.3 Cleaning the Rollers
2.
Pull the ADF release lever toward you and lift up the ADF sheet guide.
ADF upper sheet guide
3
DAILY CARE
ADF release lever
3.
Pressing down on the upper part of the Guide plate with your fingers at
the two positions shown and then pull the plate toward you to remove it.
Pad ASSY
Guide plate
3.3 Cleaning the Rollers 3-15
4.
Turn the bail of the Brake roller upward and release the lock.
Brake roller
Bail
5.
3-16
Pull the Brake roller toward you to remove it.
3.3 Cleaning the Rollers
6.
Wipe the Brake roller unit using a lint free cloth moistened with cleaner
F1.
Brake roller
3
DAILY CARE
7.
Re-install the Brake roller unit in the reverse order of its removal. By
holding the bail toward you, put the Brake roller into bracket and rotate
down until it locks in.
8.
Install the Guide plate in the reverse order of the removal. By pressing the
Guide plate down, and pushing the Guide plate back, you can install it
smoothly.
9.
Lower the ADF upper sheet guide carefully.
10. Lift the Upper transport unit to release the safety lock, then lower the unit
carefully and push the unit to close it completely.
3.3 Cleaning the Rollers 3-17
■ Cleaning the Feed rollers
1.
Remove documents from the stacker. Pull up the lever on the right front
of the Upper transport and then raise it.
CAUTION
3-18
Raise the Upper transport unit fully, then lower it to engage lock before you
put your hands inside of the scanner.
3.3 Cleaning the Rollers
2.
Wipe the metal feed rollers using a lint free cloth moistened with cleaner
F2. Wipe the rollers thoroughly. If the rollers have black build-up, the feed
reliability is affected.
Feed rollers (in 12 locations)
3
DAILY CARE
Use cleaner F2 only on metal rollers (only the Feed rollers).
CAUTION
3.
Lift the Upper transport unit to release the safety lock, then lower the unit
carefully and push the unit to close it completely.
3.3 Cleaning the Rollers 3-19
■ Cleaning the Pinch rollers
1.
Remove documents from the stacker. Pull up the lever on the right front
of the Upper transport and then raise it.
CAUTION
3-20
Raise the Upper transport unit fully, then lower it to engage lock before you
put your hands inside of the scanner.
3.3 Cleaning the Rollers
2.
Wipe the pinch rollers using a cloth moistened with cleaner F1.
Pinch roller (in 12 locations)
3
DAILY CARE
3.
Lift the Upper transport unit to release the safety lock, then lower the unit
carefully and push the unit to close it completely.
3.3 Cleaning the Rollers 3-21
3.4 Cleaning the Transport Path
■ Cleaning the Transport path
1.
Remove documents from the stacker first. Pull up the lever on the right
front of the Upper transport and then raise it.
CAUTION
3-22
Raise the Upper transport unit fully, then lower it to engage lock before you
put your hands inside of the scanner.
3.4 Cleaning the Transport Path
2.
Wipe and clean the whole transport path using a cloth moistened with
cleaner F1.
HINT
Vacuum the transport path if there are paper dust in the path.
Do not use aerosol sprays to clean the path.
3
Transport path
3.
Lift the Upper transport unit to release the safety lock, then lower the unit
carefully and push the unit to close it completely.
3.4 Cleaning the Transport Path 3-23
DAILY CARE
CAUTION
Do not use HIgh Pressure Air to blow dust out of the scanner. This will contaminate the optics and mechanism.
3.5 Cleaning the Discharge Brush
1.
Remove documents from the stacker. Pull up the lever on the right front
of the Upper transport and then raise it.
CAUTION
3-24
Raise the Upper transport unit fully, then lower it to engage lock before you
put your hands inside of the scanner.
3.5 Cleaning the Discharge Brush
2.
Pull the ADF release lever toward you and lift up the ADF sheet guide.
ADF upper sheet guide
3
DAILY CARE
ADF release lever
3.
Slide the Pick roller unit to the left to disengage the clutch ring from the
shaft.
Pick roller unit
Ring
Shaft
3.5 Cleaning the Discharge Brush 3-25
4.
Pressing down on the upper part of the Guide plate with your fingers at
the two positions shown and then rotate the plate toward you to remove
it.
Pad ASSY
Guide plate
5.
Release the lock and then hold and rotate the bail of the Pick roller unit
upward to release the lock.
Brake roller
Bail
3-26
3.5 Cleaning the Discharge Brush
6.
Pull the Brake roller unit toward you to remove it.
3
Wipe off the dust from the two discharge brushes:
one at the Pick roller side, the other at the Brake roller side.
Discharge brush(for Pick roller unit)
Discharge brush(for brakeroller)
8.
Re-install the Brake roller unit in the reverse order of its removal. By
holding the bail toward you, put the Brake roller unit into bracket and
rotate down until it locks in.
3.5 Cleaning the Discharge Brush 3-27
DAILY CARE
7.
9.
Install the Guide plate in the reverse order of the removal. You should
push it down and rotate back then the installation can be done smoothly.
10. Lower the ADF upper sheet guide slowly.
11. Lift the Upper transport unit to release the safety lock, then lower the unit
carefully and push the unit to close it completely.
3-28
3.5 Cleaning the Discharge Brush
3.6 Cleaning the Glass Surface
■ Cleaning of the removable sheet guide
CAUTION
The Lamps get very hot during use. Wait until the Lamps are cooled down
before touching.
Do not allow F1 cleaner to contact hot lamps.
Remove documents from the stacker. Pull up the lever on the right front
of the Upper transport and then raise it.
CAUTION
Raise the Upper transport unit fully, then lower it to engage lock before you
put your hands inside of the scanner.
3.6 Cleaning the Glass Surface 3-29
DAILY CARE
1.
3
2.
Use your index fingers to lift both ends of the removable sheet guide.
3.
Lift the right side first.
4.
Shift the sheet guide leftward while lifting it up to remove.
Removable sheet guide
3-30
3.6 Cleaning the Glass Surface
5.
Wipe the both sides of the glass surface using a clean lint free cloth
moistened with cleaner F1.
3
DAILY CARE
6.
Attach the removable sheet guide in the reverse order of its removal.
7.
Lift the Upper transport unit to release the safety lock, then lower the unit
carefully and push the unit to close it completely.
3.6 Cleaning the Glass Surface 3-31
■ Cleaning the Glass Sheet Guide
CAUTION
The Lamps get very hot during use. Wait until the Lamps are cooled down
before touching.
Do not allow F1 cleaner to contact hot lamps.
1.
Remove documents from the stacker. Pull up the lever on the right front
of the Upper transport and then raise it.
CAUTION
3-32
Raise the Upper transport unit fully, then lower it to engage lock before you
put your hands inside of the scanner.
3.6 Cleaning the Glass Surface
2.
Push down on the Glass sheet guide tab to open the Glass sheet guide.
3
DAILY CARE
This picture is side View.
Glass sheet guide
3.6 Cleaning the Glass Surface 3-33
3.
Wipe the Glass sheet guide using a clean lint free cloth moistened with
cleaner F1.
Glass sheet guide
Tab
4.
Lift the tabs until the Guide locks in. Close the Glass sheet guide. Make
sure that the metal part locks.
5.
Lift the Upper transport unit to release the safety lock, then lower the unit
carefully and push the unit to close it completely.
3-34
3.6 Cleaning the Glass Surface
3.7 Cleaning the Sensors
■ Cleaning the document width detection sensors
(6 positions)
1.
Remove documents from the stacker. Pull up the lever on the right front
of the Upper transport and then raise it.
CAUTION
Raise the Upper transport unit fully, then lower it to engage lock before you
put your hands inside of the scanner.
3
DAILY CARE
3.7 Cleaning the Sensors 3-35
2.
Pull the ADF release lever toward you and lift up the ADF sheet guide.
ADF upper sheet guide
ADF release lever
3.
Hold the ADF sheet guide with your hand to keep it open.
4.
Wipe the six sensor surfaces with a clean lint free cloth moistened with
cleaner F1.
Document width sensor(in 6 locations)
5.
Lower the ADF upper sheet guide gently.
6.
Lift the Upper transport unit to release the safety lock, then lower the unit
carefully and push the unit to close it completely.
3-36
3.7 Cleaning the Sensors
■ Cleaning the SF0 sensor and SF1 sensor.
1.
Remove documents from the stacker. Pull up the lever on the right front
of the Upper transport and then raise it.
CAUTION
Raise the Upper transport unit fully, then lower it to engage lock before you
put your hands inside of the scanner.
3
DAILY CARE
3.7 Cleaning the Sensors 3-37
2.
Pull the ADF release lever toward you and lift up the ADF sheet guide.
ADF upper sheet guide
ADF release lever
3.
Hold the ADF sheet guide with your hand to keep it open.
4.
Wipe SF0 and SF1 sensor surfaces with a clean lint free cloth moistened
with cleaner F1.
SF1 Sensor
SF0 Sensor
5.
Lower the ADF upper sheet guide gently.
6.
Lift the Upper transport unit to release the safety lock, then lower the unit
carefully and push the unit to close it completely.
3-38
3.7 Cleaning the Sensors
■ Cleaning the SF1.5 sensor and SF2 sensor
1.
Remove documents from the stacker. Pull up the lever on the right front
of the Upper transport and then raise it.
CAUTION
Raise the Upper transport unit fully, then lower it to engage lock before you
put your hands inside of the scanner.
3
DAILY CARE
3.7 Cleaning the Sensors 3-39
2.
Wipe SF1.5 and SF2 sensor surfaces with a clean lint free cloth
moistened with cleaner F1.
SF2 Sensor
SF1.5 Sensor
3.
3-40
Lift the Upper transport unit to release the safety lock, then lower the unit
carefully and push the unit to close it completely.
3.7 Cleaning the Sensors
3.8 Cleaning the Lamps
CAUTION
The Lamps get very hot during use. Wait until
the Lamps are cooled down before touching.
Never replace the Lamp without turning off the power.
Do not allow F1 cleaner to contact hot lamps.
DAILY CARE
■ Front-side lamp
1.
Remove documents from the stacker. Pull up the lever on the right front
of the Upper transport and then raise it.
CAUTION
3
Raise the Upper transport unit fully, then lower it to engage
lock before you put your hands inside of the scanner.
3.8 Cleaning the Lamps 3-41
2.
Push down on the Glass sheet guide tab to open the Glass sheet guide.
This picture is side View.
3-42
3.8 Cleaning the Lamps
Glass sheet guide
3
DAILY CARE
3.8 Cleaning the Lamps 3-43
3.
Pull down on the tab to release the Lamp socket covers attached to the
both ends of the Lamp to remove them.
Tab
4.
Rotate the Lamp a half turn so that the terminals on each end align with
the slot on the Lamp socket. Then remove the Lamp from the socket.
Lamp socket
3-44
3.8 Cleaning the Lamps
5.
Clean the clear portion of the Lamp with a clean lint free dry cloth.
Clear portion
3
Attach the front-side Lamp in the reverse order of its removal. Make sure
that the clear portion of the Lamp faces down.
ATTENTION
If the Lamp is installed with the clear portion facing incorrect direction, an
error due to insufficient light occurs.
3.8 Cleaning the Lamps 3-45
DAILY CARE
6.
7.
Attach the Lamp socket cover in the reverse order of its removal. Engage
the socket cover hook to the Lamp frame then rotate forward as shown
below, to attach the covers.
Lamp socket cover
8.
Close the Glass sheet guide. Make sure that the guide is fixed firmly.
9.
Lift the Upper transport unit to release the safety lock, then lower the unit
carefully and push the unit to close it completely.
3-46
3.8 Cleaning the Lamps
■ Back-side lamp
1.
Push back blue latch to release the side cover, then open.
3
DAILY CARE
Side cover
2.
Hold the handle (blue part) and pull the Back-side lamp unit out of the
scanner.
3.8 Cleaning the Lamps 3-47
3.
Rotate the Lamp a half turn so that the terminals on each end align with
the slot on the Lamp socket and remove the Lamp from the unit.
Lamp socket
Backside lamp unit
4.
Clean the clear portion of the Lamp with a dry cloth.
Clear portion
3-48
3.8 Cleaning the Lamps
5.
Install the Back-lamp unit in the reverse order of its removal. Make sure
that the clear portion of the Lamp faces up.
3
DAILY CARE
ATTENTION
If the Lamp is installed with the clear portion facing incorrect direction, an
error due to insufficient light occurs.
6.
Install the Back-lamp in the reverse order of its removal. Make sure the
connectors meet properly.
7.
Close the side cover. Confirm that the latch is closed securely.
3.8 Cleaning the Lamps 3-49
3-50
3.8 Cleaning the Lamps
4
REPLACEMENT OF
CONSUMABLES
This chapter describes how to replace consumables.
4.1 Consumables and Replacement Cycle.............................4-2
4.2 How to check the Abrasion Counter.................................4-3
4.3 Replacing the Pad ASSY....................................................4-4
4.4 Replacing the Pick Roller Unit ..........................................4-9
4.5 Replacing the Brake Roller Unit......................................4-12
4.6 Replacing the Front-side Lamp.......................................4-15
4.7 Replacing the Back-side Lamp .......................................4-20
4-1
4.1 Consumables and Replacement
Cycle
The following table lists the Part No. and the standard replacement cycle of the consumables. It is
recommended that you stock extra consumables before the ones in the scanner reach the end of
Their service life. The consumables must be replaced periodically. You can check the number of
scanned pages for the Pad ASSY, the Pick roller unit, the Brake roller unit, and Print cartridge,
and you can check the cumulative lamp-on time for the Lamps by referring to each counter on this
scanner.
Descriptions
Part No.
Standard replacement cycle
Lamp
PA83950-0290
1,000 Hours(60,000minutes)
Pad ASSY
CA04315-G730
300,000 sheets or 1 year
Pick Roller Unit
PA03296-F711
300,000 sheets or 1 year
Brake Roller Unit
CA04315-F705
300,000 sheets or 1 year
Print Cartridge
CA00050-0262
Black ink cartridge
4,000,000 characters
The replacement cycle is based on the printing on Letter/A4 woodfree paper or wood containing
paper documents (64 g/m2). The replacement cycle may differ due to paper quality, print density
or paper type.
For the purchase of the consumables, please contact the FUJITSU scanner dealer where you
purchased your scanner.
ATTENTION
4-2
Use the correct Print cartridge. The Scanner may be damaged if the wrong
Print cartridge is installed.
4.1 Consumables and Replacement Cycle
4.2 How to check the Abrasion Counter
■ Checking the counter from the Operator panel
The number displayed on the right bottom of LCD in the "Ready" status shows the consumables
count. The Abrasion counter, shown below indicates the highest cumulative number of sheets
scanned by the PAD ASSY, the Pick roller unit or the Brake roller unit.
4
Batch counter
e
a
d
y
x
x
x
x
x
x
x
x
x
x
x
REPLACEMENT OF CONSUMABLES
R
Abrasion counter
HINT
When the counter is zero, nothing is displayed.
Batch counter indicates the number of scanned pages of one batch.
4.2 How to check the Abrasion Counter
4-3
4.3 Replacing the Pad ASSY
1.
Remove documents from the stacker. Pull up the lever on the right front
of the Upper transport and then raise it.
CAUTION
4-4
Raise the Upper transport unit fully, then lower it to engage lock before you
put your hands inside of the scanner.
4.3 Replacing the Pad ASSY
2.
Pull the ADF release lever toward you and lift up the ADF sheet guide.
ADF upper sheet guide
4
3.
Press down on the upper part of the Guide plate with your fingers at the
two positions shown and then rotate the plate toward you to remove it.
Pad ASSY
Guide plate
4.3 Replacing the Pad ASSY
4-5
REPLACEMENT OF CONSUMABLES
ADF release lever
Pad (cleaning area)
Pad ASSY
Guide plate
4-6
4.3 Replacing the Pad ASSY
4.
Remove the Pad ASSY from the Guide plate by pushing the removal metal
scroll down and then release hooks.
4
REPLACEMENT OF CONSUMABLES
4.3 Replacing the Pad ASSY
4-7
5.
Attach a new Pad ASSY by engaging the hooks then pressing scroll into
the slot of the Guide plate.
Hooks
ATTENTION
Confirm that the pad is firmly attached to the guide. Make sure that the two
tabs are engaged with the Guide plate.
If not attached firmly, paper feed errors such as document jams may occur.
6.
Install the Guide plate in the reverse order of the removal. By pressing the
Guide plate down and pushing the Guide plate back then you can install it
smoothly.
7.
Lower the ADF upper sheet guide gently.
8.
Lift the Upper transport unit to release the safety lock, then lower the unit
carefully and push the unit to close it completely.
9.
Clear the Pad counter.
Please refer to the section “7.3 Setup Mode Details”, “ 9. Abrasion counter
(Abrasion CNT) reset” on page 7-34.
4-8
4.3 Replacing the Pad ASSY
4.4 Replacing the Pick Roller Unit
1.
Remove documents from the stacker. Pull up the lever on the right front
of the Upper transport and then raise it.
CAUTION
Raise the Upper transport unit fully, then lower it to engage lock before you
put your hands inside of the scanner.
4
REPLACEMENT OF CONSUMABLES
4.4 Replacing the Pick Roller Unit
4-9
2.
While pulling the ADF lever toward you, lift up the ADF upper sheet guide.
ADF upper sheet guide
ADF release lever
3.
Lift up the Pick roller unit a little. Slide the Pick roller unit to the left to
disengage the clutch ring from the shaft.
Pick roller unit
Ring
Shaft
4-10
4.4 Replacing the Pick Roller Unit
4.
Install a new Pick roller unit in the reverse order of its removal.
HINT
When attaching the Pick roller unit, hold the unit as shown.
Engage the drive ring onto the drive shaft. Move left and align
the clutch ring with the shaft and move right to engage.
Correct installation
5.
Lower the ADF upper sheet guide carefully.
6.
Lift the Upper transport unit to release the safety lock, then lower the unit
carefully and push the unit to close it completely.
7.
Clear the Pick roller counter.
Please refer to the section “7.3 Setup Mode Details”, “ 9. Abrasion counter
(Abrasion CNT) reset ” on page 7-34.
4.4 Replacing the Pick Roller Unit 4-11
REPLACEMENT OF CONSUMABLES
Incorrect installation
4
4.5 Replacing the Brake Roller Unit
1.
Remove documents from the stacker. Pull up the lever on the right front
of the Upper transport and then raise it.
CAUTION
2.
Raise the Upper transport unit fully, then lower it to engage lock before you
put your hands inside of the scanner.
Pull the ADF release lever toward you and lift up the ADF sheet guide.
ADF upper sheet guide
ADF release lever
4-12
4.5 Replacing the Brake Roller Unit
3.
Press down on the upper part of the Guide plate with your fingers at the
two positions shown and rotate the plate toward you to remove it.
Pad ASSY
4
4.
Turn the bail of the Brake roller upward and release the lock.
Brake roller
Bail
4.5 Replacing the Brake Roller Unit 4-13
REPLACEMENT OF CONSUMABLES
Guide plate
5.
Pull the Brake roller toward you to remove it.
Brake roller
6.
Install a new Brake roller unit in the reverse order of its removal. By
holding the bail toward you, put the Brake roller into bracket and rotate
down until it locks in.
7.
Install the Guide plate in the reverse order of the removal. By pressing the
Guide plate down and pushing the Guide plate back, you can install it
smoothly.
8.
Lower the ADF upper sheet guide carefully.
9.
Lift the Upper transport unit to release the safety lock, then lower the unit
carefully and push the unit to close it completely.
10. Clear the Brake roller counter.
Please refer to the section “7.3 Setup Mode Details”, “ 9. Abrasion counter
(Abrasion CNT) reset ” on page 7-34.
4-14
4.5 Replacing the Brake Roller Unit
4.6 Replacing the Front-side Lamp
Never replace the Lamp without turning off the power.
CAUTION
Wait 5 minutes after turning off the power before touching the Lamp.
Remove documents from the stacker. Pull up the lever on the right front
of the Upper transport and then raise it.
CAUTION
Raise the Upper transport unit fully, then lower it to engage lock before you
put your hands inside of the scanner.
4.6 Replacing the Front-side Lamp 4-15
REPLACEMENT OF CONSUMABLES
1.
4
2.
Pull down the Glass sheet guide tab and open the Glass sheet guide.
This picture is side View.
Glass sheet guide
4-16
4.6 Replacing the Front-side Lamp
3.
Pulling down the Lamp socket covers attached to the both end of the
Lamp sockets and remove them.
Tab
4
Rotate the Lamp a half turn so that the terminals on each end align with
the slot on the Lamp socket and remove the Lamp from the unit.
Lamp socket
4.6 Replacing the Front-side Lamp 4-17
REPLACEMENT OF CONSUMABLES
4.
5.
Install a new Lamp in the reverse order of the removal. Make sure that the
clear portion of the Lamp faces down.
ATTENTION
4-18
If the Lamp is installed with the clear portion facing incorrect direction, an
error due to insufficient light occurs.
4.6 Replacing the Front-side Lamp
6.
Attach the Lamp socket cover in the reverse order of its removal. Make
sure that the metal part is fixed firmly.
Lamp socket cover
4
Close the glass sheet guide. Make sure that the guide is fixed firmly.
8.
Lift the Upper transport unit a little to release the safety lock and then
lower the unit slowly, then push the unit to close it completely.
9.
Clear the Front-side lamp counter.
Please refer to the section “7.3 Setup Mode Details”, “ 9. Abrasion counter
(Abrasion CNT) reset ” on page 7-34.
HINT
You can check the cumulative lamp-on time from the Operator
panel Test mode.
For the details, refer to the section "7.5 Test Mode Details " " 3.
Display the cumulative lamp-on time " on page 7-79.
4.6 Replacing the Front-side Lamp 4-19
REPLACEMENT OF CONSUMABLES
7.
4.7 Replacing the Back-side Lamp
Never replace the Lamp without turning off the power.
CAUTION
Wait 5 minutes after turning off the power before touching the Lamp.
1.
Pull and open the side cover.
Side cover
4-20
4.7 Replacing the Back-side Lamp
2.
Hold the handle (blue part) and pull out the Back-side lamp unit.
4
Rotate the Lamp a half turn so that the terminals on each end align with
the slot on the Lamp socket and remove the Lamp from the unit.
Lamp socket
Backside lamp unit
4.7 Replacing the Back-side Lamp 4-21
REPLACEMENT OF CONSUMABLES
3.
4.
Attach a new Lamp following the reverse order of old lamp removal. Make
sure that the clear portion of the Lamp faces up.
ATTENTION
4-22
If the Lamp is installed with the clear portion facing incorrect direction, an
error due to insufficient light occurs.
4.7 Replacing the Back-side Lamp
5.
Install the Back-lamp unit in the reverse order of its removal. Make sure
the connectors meet properly.
4
Close the side cover. Confirm that the cover is closed securely.
7.
Clear the Rear-side lamp counter.
Please refer to the section “7.3 Setup Mode Details”, “ 9. Abrasion counter
(Abrasion CNT) reset ” on page 7-34.
HINT
You can check the cumulative lamp-on time from the Operator panel Test
mode.
For the details, refer to the section "7.5 Test Mode Details", "3.Display the
cumulative lamp-on time" on page 7-79.
4.7 Replacing the Back-side Lamp 4-23
REPLACEMENT OF CONSUMABLES
6.
4-24
4.7 Replacing the Back-side Lamp
5
SOLVING COMMON
PROBLEMS
This chapter describes how to clear document jams, how to remedy other
problems, items to be checked before contacting an authorized service
provider and how to check labels on the scanner.
5.1 Clearing Document Jams ..................................................5-2
5.2 Troubleshooting .................................................................5-8
5.3 Before Contacting a Service Provider ............................5-30
5.4 Labels on the Scanner .....................................................5-32
5-1
5.1 Clearing Document Jams
If a document jam occurs during feeding, follow the procedure below to remove the jammed
documents.
• Be careful not to get injured during jam removal.
CAUTION
• When removing jammed documents, be careful not to get your
neckties or necklaces entangled inside the scanners.
• The surface of the glass may be hot during the operation. Take care
not to get burned.
■ Removing jams from the hopper or the transport
path
1.
Remove the documents on the stacker. Pull up the lever on the right front
of the Upper transport and then raise it.
CAUTION
5-2
Raise the Upper transport unit fully, then lower it to engage lock before you
put your hands inside of the scanner.
5.1 Clearing Document Jams
2.
While pulling the ADF lever toward you, lift up the ADF upper sheet guide.
ADF upper sheet guide
5
3.
Remove the jammed document.
ATTENTION
- Staples and paper clips etc. can cause document jams.
- Make sure you check the document and the document transport path for
obstructions before you start scanning again.
- Remove staples and paper clips from the documents before you start scanning.
4.
Lower the ADF upper sheet guide carefully.
5.
Lift the Upper transport unit to release the safety lock, then lower the unit
carefully and push the unit to close it completely.
5.1 Clearing Document Jams
5-3
SOLVING COMMON PROBLEMS
ADF release lever
■ Removing jams from the eject mechanism.
1.
Remove the documents on the stacker. Pull up the lever on the right front
of the Upper transport and then raise it.
ADF upper sheet guide
ADF release lever
2.
Pull out the jammed document to the stacker.
3.
Lift the Upper transport unit to release the safety lock, then lower the unit
carefully and push the unit to close it completely.
5-4
5.1 Clearing Document Jams
■ Document separation force adjustment
If the following error occurs frequently, adjust the brake force of the Brake roller using setup
mode.
- Double-feed
- Mis-pick
- Paper jam1
Enter into the setup mode.
Please refer to the section "1 Basic Operations of the Operator Panel", "Using
the setup and the test modes" on page1-10.
The following screen appears.
!
=
0
1
T
h
S
i
e
n
p
a
r
a
t
J
J
J
F
F
i
T
o
h
n
i
c
k
Choose an appropriate setting based on the thickness of the document you are
scanning and the error.
By pressing
(1).
(Right arrow button), the LCD display changes items from (5) to
By pressing
(5).
(Left arrow button), the LCD display changes items from (1) to
(1)
-
Document thickness: Thick
(2)
-
Document thickness: Medium thick
(3)
-
Document thickness: Medium
(4)
-
Document thickness: Medium thin
(5)
-
Document thickness: Thin
When the desired option appears, press
(Enter button) to select it.
5.1 Clearing Document Jams
5-5
SOLVING COMMON PROBLEMS
1.
5
Document separation force setup items are as follows.
Setting
Document
thickness
Document separation force
Thick
Thick
Strong
Medium Thick
Medium Thick
Less strong
Medium
Medium
Medium
(Factory default
setting)
Medium Thin
Medium Thin
Medium Weak
Thin
Thin
Weak
"Double-feed"
occurs frequently
"Mis-pick" or
"Document jam"
occurs frequently
Increase document Decrease document
separation force
separation force
If Mis-pick occurs frequently, adjust the Pick roller rotation speed.
Press
(Next button) to show the following screen.
!
=
Press
Press
0
(Left arrow button) or
3
F
a
P
s
i
t
c
/
The blinking item is the one selected.
5-6
5.1 Clearing Document Jams
i
S
d
p
/
e
S
e
l
d
o
w
(Right arrow button) and select an item.
(Enter button) to select the setting.
HINT
k
M
Pick speed
Mis-pick occurs frequently
Fast (Factory default)
Decrease pick speed
Mid
Slow
5
When you set pick speed at "Mid" or "Slow", scanning speed is reduced.
ATTENTION
SOLVING COMMON PROBLEMS
5.1 Clearing Document Jams
5-7
5.2 Troubleshooting
This section describes common troubles during usage and how to remedy the troubles.
Before you ask for repair service, check the following flowchart to determine the trouble.
If you can not resolve the trouble after following the flowcharts, please check the items in section
"5.3 Before Contacting a Service Provider" on page 5-30, and then contact an authorized
FUJITSU Scanner service provider.
5-8
5.2 Troubleshooting
Synptom1
Scanner cannot be turned on.
NO
5
Check that the outlet has power.
Connect the power cord.
Is the power cord connected?
SOLVING COMMON PROBLEMS
YES
NO
Press the "I" side of the main
line switch.
Have you turned on the main line
switch?
YES
NO
Have you pushed the power button
on the operator panel?
Press the power button.
YES
Contact an authorized FUJITSU
Scanner service provider.
5.2 Troubleshooting
5-9
Symptom2
The operator panel LCD goes out.
YES
Has it beena while since you turned
on the scanner ? (15 to 60 minutes)
Scanner is in Power save
mode. Press any button (except
Power button) on the operator
panel to wake it up.
NO
NO
Does the LCD remain blank even after
the scanner has been turned on again?
The scanner operation is
normal.
YES
Contact an authorized FUJITSU
Scanner service provider.
(* ) Press any button except Power button. The Power button will not work to wake up
the scanner. Pressing the power button more than 2 seconds will turn off the power.
5-10
5.2 Troubleshooting
Symtom3
Scanning does not start.
NO
Are the documents loaded properly
on the hopper?
Load the documents centered
in the hopper.
NO
Is the upper transport unit closed
correctly?
Close the upper transport unit
correctly.
YES
Is the interface cable connected
properly?
NO
Connect the interface cable
properly.
YES
Is the SCSI ID set correctly?
NO
Set the SCSI ID correctly
from the operator panel of the
scanner. (* 1)
YES
Continued on next page
5.2 Troubleshooting 5-11
SOLVING COMMON PROBLEMS
YES
5
Continued from the previous page
Has the scanner been selected by
multiple applications ?
YES
Close all applications and
select the scanner from only
one application.
NO
Is the Check LED blinking?
NO
The scanner operation is
normal.
YES
Check LCD display for error.
Eliminate the cause of user
recoverable errors. Is the LED still
blinking?
NO
The scanner operation is
normal.
YES
Continued on next page
5-12
5.2 Troubleshooting
Continued from the previous page
NO
Is the Check LED lit?
The scanner operation is
normal.
YES
NO
The scanner operation is
normal.
YES
Contact an authorized FUJITSU
Scanner service provider.
(* 1) For the details on how to set SCSI ID, refer to the section “7.3 Setup Mode Details”,
“19. Setting SCSI ID” on page 7-49.
5.2 Troubleshooting 5-13
SOLVING COMMON PROBLEMS
Turn the power off and on again.
Is the Check LED lit?
5
Symptom4
Quality of scanned pictures and photographs is
not satisfactory.
NO
Select "Photo" mode (white
level following off) on the
scanner setup menu in your
application. (* 1)
NO
Select halftoning or dithering
mode on your PC.
Is "Photo"mode selected?
YES
Is halftoning or dithering processing
selected?
YES
Is the document path, the Removable
sheet guide, the Glass sheet guide
and/or the Lamp(s) clean?
NO
Clean the scanner completely.
(* 2)
YES
Are the Lamps installed correctly?
NO
Re-install the lamps correctly.
(* 3)
YES
Continued on next page
5-14
5.2 Troubleshooting
Continued from the previous page
Contact an authorized FUJITSU
Scanner service provider.
5
SOLVING COMMON PROBLEMS
(* 1) If Binary mode is used, the scanned image of a photograph may not be good.
Depending on the applications used, the method to specify “Photo” mode and the
name of the mode can be different. If the application allows you to change the
setting from scanner driver setting dialog, specify [Halftone], [Gray scale] or [24bit
Color] for Image Mode. In [Halftone] mode, you have to specify Dither pattern.
(* 2) For the details of cleaning, refer to "3 DAILY CARE" on page 3-1.
(* 3) For the details on how to replace Lamps, refer to "4 REPLACEMENT OF
CONSUMABLES" on page 4-1.
5.2 Troubleshooting 5-15
Symptom5
Quality of scanned text or lines is unsatisfactory.
NO
Is "Line Art" mode selected?
Select "Line Art" mode from
your PC. (* 1)
YES
Is the document path, the Removable
sheet guide, the Glass sheet guide
and/or the Lamp(s) clean?
NO
Clean the scanner completely.
(* 2)
YES
Contact an authorized FUJITSU
Scanner service provider.
(* 1) If halftone mode is used, the scanned image of text or line art may not be good.
Depending on the applications used, the method to specify “Line Art” mode and the
name of the mode can be different. If the application allows you to change the
setting from scanner driver setting dialog, specify [Black & White] for Image Mode.
(* 2 For the details of cleaning, refer to "3 DAILY CARE" on page 3-1.
5-16
5.2 Troubleshooting
Symptom6
The scanned image is distorted and/or not
sharp.
Is the document path, the Removable
sheet guide, the Glass sheet guide
and/or the Lamp(s) clean?
YES
Clean the scanner completely.
(* )
Is the scanner installed on a flat and
level surface?
NO
Install the scanner on a flat and
level surface.
YES
Contact an authorized FUJITSU
Scanner service provider.
(* ) For the details of cleaning, refer to "3 DAILY CARE" on page 3-1.
5.2 Troubleshooting 5-17
SOLVING COMMON PROBLEMS
NO
5
Symptom7
Vertical streaks appear in the scanned image.
YES
Are the streaks black?
Clean the Removable sheet
guide , and the Glass sheet
guide. (* 1)
NO
Is there text in the top 3mm area of
the scanned document and is the
"Line Art" mode selected.
YES
Select "Photo" mode.
NO
YES
Are the Lamp(s) more than 1,000
hours old? Has the Lamp(s) burned
out? (* 2)
Replace the Lamp. (* 3)
NO
Contact an authorized FUJITSU
Scanner service provider.
(* 1) For the cleaning of the removable sheet guide, and the glass sheet guide, please
refer to "3 DAILY CARE" on page 3-1.
(* 2) For the details on how to check the lamp-on time, please refer to the section "7.5
Test Mode Details", "3. Display the cumulative lamp-on time" on page 7-79.
(* 3) For the details on how to replace Lamps, refer to "4 REPLACEMENT OF
CONSUMABLES".
5-18
5.2 Troubleshooting
Symptom8
Check LED starts blinking right after power on.
Eliminate the cause of user recoverable error. (* )
Is the Check LED blinking still?
NO
The scanner operation is
normal.
SOLVING COMMON PROBLEMS
YES
5
Contact an authorized FUJITSU
Scanner service provider.
(* ) For the message display contents and the error recovery method, refer to
“APPENDIX3 MESSAGES OF OPERATOR PANEL”, “Error message (Temporary
error)” on page AP-9.
5.2 Troubleshooting 5-19
Symptom9
The Check LED lights right after power on.
Turn off the power and on again.
Is the check LED lit again?
YES
Contact an authorized FUJITSU
Scanner service provider.
5-20
5.2 Troubleshooting
NO
The scanner operation is
normal.
Symtom10
Double-feed occurs frequently.
Do the documents satisfy the
conditions described in "6.2 Document
Quality," "Precautions"?
NO
Use documents which satisfy
the requirements. (* 1)
When double-feed detection is on,
are the double-feed detection
conditions (*2) satisfied?
NO
To take necessary actions to
satisfy the requirements. (* 2)
YES
NO
Did you fan the documents before
loading them on the hopper?
Fan the documents a few
times before loading.
YES
Are the documents recently printed
on a copier or Laser printer?
YES
Fan the documents a few
times to eliminate static
electricity.
NO
Continued on next page
5.2 Troubleshooting 5-21
SOLVING COMMON PROBLEMS
YES
5
Continued from the previous page
YES
Clean the Pad ASSY. (* 3)
YES
Replace the Pad ASSY. (* 4)
NO
Install the Pad ASSY properly.
(* 4)
Is the Pad ASSY dirty?
NO
Is the Pad ASSY worn out?
NO
Is the Pad ASSY installed properly?
YES
Are the Pick roller, the Brake roller
or the document path dirty?
YES
Clean the scanner completely.
(* 5)
NO
Continued on next page
5-22
5.2 Troubleshooting
Continued from the previous page
Are the Pick roller unit and the
Brake roller unit installed properly?
NO
nstall the Pick roller and the
Brake roller properly. (* 6)
5
YES
YES
Replace the Pick roller unit and
the Brake roller unit if
necessary. (*6)
NO
Contact an authorized FUJITSU
Scanner service provider.
(* 1)
For the details on required conditions, refer to the section "6.2 Document
Quality" on page 6-3.
(* 2)
For the double-feed detection conditions, refer to "APPENDIX2 DOUBLEFEED DETECTION CONDITIONS" on page AP-2.
(* 3), (* 5) For the details on how to clean scanner, refer to "Chapter 3 DAILY CARE" on
page 3-1.
(* 4)
For the details on how to replace Pas ASSY, refer to "4 REPLACEMENT OF
CONSUMABLES" on page 4-1.
(* 6)
For the details on how to replace and install Pick roller unit and Brake roller
unit, refer to "4 REPLACEMENT OF CONSUMABLES" on page 4-1.
(* 7)
Check the wear of rollers. For the method to check the number of sheets
scanned for each consumable, refer to “7.3 Setup Mode Details”, “9. Abrasion
counter reset” on page 7-34.
5.2 Troubleshooting 5-23
SOLVING COMMON PROBLEMS
Have you scanned many sheets?
Check the consumables life to ensure
you have not scanned more than
300,000 sheets. (* 7)
Symptom11
Document jam occurs frequently.
Do the documents satisfy the
conditions described in "6.2 Document
Quality," "Precautions"?
NO
Use documents which satisfy
the requirements. (* 1)
YES
Is the length of the documents shorter
than 80mm and is the paper length
set [Normal]?
YES
Select paper length [Short] in
Paper Length setup mode.
(* 2)
NO
YES
Clean the ADF paper path or
remove the foreign objects.
(* 3)
NO
Re-install the Pad ASSY
properly. (* 4)
Is there any foreign objects in the
ADF paper path?
NO
Is the Pad ASSY installed properly?
YES
Continued on next page
5-24
5.2 Troubleshooting
Continued from the previous page
Are the Pick roller, the Brake roller
and the Pinch rollers dirty?
YES
Clean the dirty parts. (* 5)
5
NO
NO
Install the Pick roller and the
Brake roller properly. (* 6)
YES
Replace the Pick roller unit and
the Brake roller unit if
necessary. (*6)
YES
Have you scanned many sheets?
Check consumables life to ensure
you have not scanned more than
300,000 pages. (* 7)
NO
Contact an authorized FUJITSU
Scanner service provider.
(* 1) For the details on required conditions, refer to the section "6.2 Document Quality"
on page 6-3.
(* 2) For the details on how to set up the Paper Length, refer to "7.3 Setup Mode Details",
"10. Setting Short document scan mode (Paper Length setup)" on page 7-37.
(* 3) For the details on how to clean ADF, refer to "Chapter 3 DAILY CARE" on page 3-1.
(* 4) For the details on how to replace Pas ASSY, refer to "4 REPLACEMENT OF
CONSUMABLES" on page 4-1.
(* 5) For the details on scanner cleaning, refer to "Chapter 3 DAILY CARE" on page 3-1.
(* 6) For the replacement and re-installation of Pick roller unit and Brake roller unit,
please refer to "4 REPLACEMENT OF CONSUMABLES" on page 4-1.
(* 7) Check the consumable wear. For the method to check the number of sheets
scanned for each consumable, refer to “7.3 Setup Mode Details”, “9. Abrasion
counter reset” on page 7-34.
5.2 Troubleshooting 5-25
SOLVING COMMON PROBLEMS
Are the Pick roller unit and the Brake
roller unit installed properly?
Symptom12
There is a shadow on the leading edge of
the scanned image.
YES
Did you adjust the offset (position to
start scanning the documents)?
Contact an authorized FUJITSU
Scanner service provider.
NO
Do the offset adjustment.
Which OS are you using?
Windows 98/
Windows Me/
Windows 2000/
Windows XP
Display [Control panel] [Scanners and Cameras] [Device set] and adjust the
offset. "Offset setting Sub."
Windows 95/
Windows NT 4.0
YES
Is the Scanner Control Center icon
displayed in the task tray?
NO
Select [FUJITSU Scanner Control
Center] from the Start menu and
run it.
Right click on Scanner Control
Center icon and select
[Options].
Adjust the vertical magnification.
5-26
5.2 Troubleshooting
Symptom13
Scanner is not recognized by PC
automatically.
Is the power turned on?
NO
Turn on the power.
Has there been an incomplete driver
installation in the past?
NO
Re-install the driver.
(* 1)
YES
YES
Is Adaptec EZ-SCSI installed ?
Uninstall EZ-SCSI first, then
install the driver.
NO
YES
Is the Check LED on the operator
panel lit?
Contact an authorized FUJITSU
Scanner service provider.
NO
Continued on next page
5.2 Troubleshooting 5-27
SOLVING COMMON PROBLEMS
YES
5
Continued from the previous page
Is the interface cable connected
properly?
NO
Connect the interface cable
properly.
YES
YES
Is the Check LED on the operator
panel blinking?
Check LCD display for error.
Eliminate the cause of the error.
(* 2)
NO
Contact an authorized FUJITSU
Scanner service provider.
(* 1) For the details on how to install FUJITSU TWAIN, refer to “FUJITSU TWAIN32
Scanner Driver (Scanner Utility for Microsoft Windows) User’s Guide,” “3.
Installation.” The User’s Guide is included in the FUJITSU TWAIN CD-ROM.
(* 2) For the details of error messages, refer to "APPENDIX3 MESSAGES OF
OPERATOR PANEL" on page AP-5.
5-28
5.2 Troubleshooting
Symptom14
Windows system gets unstable.
Is the OS WindowsNT 4.0?
YES
The scanner operation is
normal.
Is WNASPI32.DLL installed on
the PC?
NO
The scanner operation is
normal.
YES
YES
Is ASPI version driver installed by
mistake?
Uninstall ASPI version driver
and install the correct driver.
NO
Contact an authorized FUJITSU
Scanner service provider.
(* ) For the details on how to install FUJITSU TWAIN, refer to “FUJITSU TWAIN32
Scanner Driver (Scanner Utility for Microsoft Windows) User’s Guide”, “3.
Installation.” The User’s Guide is included in the FUJITSU TWAIN CD-ROM.
5.2 Troubleshooting 5-29
SOLVING COMMON PROBLEMS
NO
5
5.3 Before Contacting a Service
Provider
Please check the following items before contacting an authorized FUJITSU Scanner service
provider.
■ General descriptions
Items to check
Information
Model
(example)
fi-4860C
Serial Number
(example)
000001
Manufacturing date
(example)
2003-08 (August 2003)
Date of purchase
(example)
October, 2003
Symptom
Frequency of trouble
For the confirmation of manufacturing information, refer to ""5.4 Labels on the Scanner" on page
5-32.
5-30
5.3 Before Contacting a Service Provider
■ Error Descriptions
Problem at the time of PC connection.
Items to check
Findings
OS (Windows) type
(example) Windows 98
Displayed error message
(example) SF0 Sensor dirty
Interface
(example) SCSI interface
Interface controller
(example) Adaptec SCSI Card 29160
Items to check
Findings
Document type
(example) Copier paper
Main purpose of use
(example) Filing company documents
Last cleaning date
(example) December 2003
Last consumable replacement date
(example) November 15, 2003
Operator panel status at trouble
(example) Paper Jam2
Imaging quality trouble
Items to check
Findings
Type and version of scanner driver
(example) FUJITSU TWAIN 9.9
Interface controller
(example) Adaptec SCSI Card 29160
OS (Windows) type
(example) Windows 2000 Professional
Application software
(example) Acrobat
Others
Items to check
Information
Can you send both the original document (or
scanned grayscale image file) and printed scanned
data (or the file) via Fax (or by e-mail)?
5.3 Before Contacting a Service Provider 5-31
SOLVING COMMON PROBLEMS
Document feed trouble
5
5.4 Labels on the Scanner
This section describes how to check the labels on the scanner.
The positions of the labels
The following shows where the two labels are located on the scanner.
Manufacturing Label (example):
Indicates scanner manufacturing information.
Regulatory label (example):
Shows the conforming standards of the scanner.
5-32
5.4 Labels on the Scanner
6
ADF DOCUMENT
SPECIFICATIONS
This chapter describes the sizes and qualities of documents required for the
satisfactory performance of the scanner.
6.1 Document Size....................................................................6-2
6.2 Document Quality...............................................................6-3
6.3 Hole-punching Prohibited Areas.......................................6-6
6.4 Print Prohibited Area..........................................................6-7
6.5 Background Color Areas ...................................................6-8
6.6 Job Separation Sheet.........................................................6-9
6.7 Hopper Capacity ...............................................................6-10
6-1
6.1 Document Size
The following shows the supported document sizes.
A
Feeding Direction
B
Maximum
A
6-2
Minimum
B
A
B
297 mm
432 mm
74 mm
74 mm
11.7 in.
17 in.
2.9 in.
2.9 in.
6.1 Document Size
6.2 Document Quality
This section describes the types and thickness of documents this scanner supports.
■ Document type
6
The recommended document types are as follows.
When using documents of a paper type other than the above, perform a test-scanning with a few
sheets of the same type before executing the actural task in order to check whether or not the
documents can be scanned.
■ Document thickness
Paper thickness is expressed by "paper weight." The following shows the paper weights that can
be used on this scanner:
52 g/m2 to 127 g/m2 or 14 lb to 34 lb (when fi-486TRK option is not installed)
6.2 Document Quality
6-3
ADF DOCUMENT SPECIFICATIONS
- Woodfree paper
- Wood containing paper
■ Precautions
The following documents may not be scanned successfully.
-
Document of non-uniform thickness (e.g. envelopes)
Wrinkled or curled documents (Refrer to HINT on the next page )
Folded or torn documents
Tracing paper
Coated paper
Carbon paper
Carbonless paper
Photosensitive paper
Perforated or punched documents
Documents that are not square or rectangular
Very thin documents
Do not use the following documents:
-
Paper-clipped or stapled documents
Documents on which the ink is still wet
Documents smaller than A7 or larger than A3
Documents other than paper such as fabric, metal foil, or transparencies
HINT
− When scanning semi-transparent documents, set the density to light to
avoid a bleed through.
− To prevent the rollers from becoming dirty, avoid scanning documents
containing large areas written or filled in pencil. If scanning of such
documents is inevitable, clean the rollers more frequently.
6-4
6.2 Document Quality
ATTENTION
• Carbonless paper contains chemical substances that may damage the
Pad ASSY or rollers (e.g. Pick roller) when documents are fed. Pay
attention to the following:
Cleaning
If pick errors occur frequently, clean the Pad ASSY and
the Pick roller. For details on cleaning the Pad ASSY ancd
the Pick roller, refer to "Chapter 3 Daily Care" on page 3-1.
Replacing parts: The service life of the Pad ASSY and Pick roller may be
shortened compared to the case of scanning wood containing paper documents.
HINT
ADF DOCUMENT SPECIFICATIONS
• When scanning wood containing paper, the service life of the Pad ASSY
and the Pick roller may be shortened compared to the case of scanning
woodfree paper.
When using the ADF, the leading edge of all document sheets must be
evenly aligned. Make sure that curling at the leading edge is within the following tolerances:
More than 30mm
Feed direction
Less than
3mm
Top of the paper
More than 30mm
Read surface
Feed direction
Less than
5mm
Top of the paper
Read surface
6.2 Document Quality
6
6-5
6.3 Hole-punching Prohibited Areas
Punched holes in the shaded areas may cause errors.
For job separation sheet requirements, please refer to the section "6.6 Job Separation Sheet" on
page 6-9.
113 (4.45")
134 (5.28")
79 (3.12") 96 (3.78")
10
10
12 12
10
10
(0.39") (0.39") (0.47") (0.47") (0.39") (0.39")
Document feeding direction
15
(0.59")
Reading
reference
position
(Unit : mm)
Top of document
Front side
Reading surface
Bottom of document
10
10
(0.39") (0.39")
Center of document
6-6
6.3 Hole-punching Prohibited Areas
6.4 Print Prohibited Area
If there is printing in area A, the document size may be mis-detected. If there is printing in area B
of a document, it may cause double-feed errors. The following figure shows print prohibited areas
on a document. If double-feed detection is to be enabled, it is recommended that you avoid
printing in these areas. These restrictions must be considered when designing forms and
documents.
For the details of double-feed detection, please refer to "APPENDIX2 DOUBLE-FEED
DETECTION CONDITIONS" on page AP-2.
Center of document
113 (4.45")
79 (3.12")
ADF DOCUMENT SPECIFICATIONS
Reading
reference
position
134 (5.28")
96 (3.78")
(Unit : mm)
Document feeding direction
15
Top of document
: Area A
: Area B
Front side
Reading surface
Bottom of document
10
10
(0.39") (0.39")
34 (1.34")
10
10
(0.39") (0.39")
6.4 Print Prohibited Area
6
6-7
6.5 Background Color Areas
Paper white detection is performed in the shaded area as shown in the Figure below. The top 3mm
on both sides of a document, should have no printing in this area.
When using dropout color, the color can be in this area. If this cannot be followed, turn the white
level follower off when reading.
For the details on dropout color, please refer to "APPENDIX1 DROP-OUT COLOR" on page
AP-1.
Reading
reference
position
Grounding color
(white) or drop-out
color area
Feeding direction
3 mm (0.12")
6-8
6.5 Background Color Areas
6.6 Job Separation Sheet
1. Shape
The following shows the typical format of the job separation sheet.
(0.59")
6
ADF DOCUMENT SPECIFICATIONS
Feeding direction
15
15
(0.59")
Center of document
(Unit : mm)
more than 210 (8.27")
2. Document Specifications
Document width must be Letter (8.5 inch)/A4 width (210mm) or wider.
6.6 Job Separation Sheet
6-9
6.7 Hopper Capacity
The number of pages that can be loaded on the Hopper depends on the paper size and the ream
weight. This information is shown in the following graph.
Capacity of Hopper (sheets)
A4/Letter or smaller
500
Legal
300
250
200
150
110
A3 or 11x17 in.
52
128
80
2
Paper weight (g/m )
Paper weight conversion table
Paper weight
6-10
Conversion
g/m2
52
64
75
80
90
104
127
157
lb
14
17
20
21
24
28
34
42
6.7 Hopper Capacity
7
OPERATOR PANEL
MENUS
This chapter explains the setup mode and the test mode of the scanner.
7.1 Setup Mode .........................................................................7-2
7.2 Setup mode functions......................................................7-10
7.3 Setup Mode Details ..........................................................7-17
7.4 Test Mode Overview .........................................................7-64
7.5 Test Mode Details .............................................................7-70
7-1
7.1 Setup Mode
■ Outline
There are two types of setup mode: Online setup mode and Offline setup mode.
From “Ready“ status, you can enter Online setup mode and you can enter offline setup mode from
offline status.
According to the selected mode, available functions are different.
To enter these modes, follow the instructions below:
- Online setup mode
When LCD indicates Ready status, press
(Next button).
The following message appears.
M
!
By pressing
o
S
d
e
e
t
u
S
p
e
l
M
e
o
c
d
1
t
e
(Enter button), the scanner enters Online setup mode.
- Offline setup mode
Press and hold
(Start button) and turn on the power.
The Operator panel LCD displays the following message.
<
Press
Press
(Left arrow button) or
M
S
O
E
D
T
E
U
S
(Exit button).
The blinking item is the one selected.
HINT
7.1 Setup Mode
L
T
E
E
C
S
T
T
>
(Right arrow button) and select [Setup].
(Enter button) to enter Offline setup mode.
To quit setup, press
7-2
E
P
■ Online setup mode restrictions
In Online setup mode, the scanner setup can be changed without turning off the power.
However, the following items cannot be changed from this mode.
7
Consumables counter reset
SCSI ID change
Product ID change
SCSI bus width change
Interface change
TPS interface baud rate change
OPERATOR PANEL MENUS
-
7.1 Setup Mode
7-3
■ Function of buttons in setup mode
Button name
Function
[Next]
Displays the next menu item without saving the change.
Referred to as Next button in this manual.
[Previous]
Displays the previous menu item without saving the change.
Referred to as Previous button in this manual.
Moves to the right item on the menu
Referred to as Right arrow button in this manual.
Moves to the left item on the menu
Referred to as Left arrow button in this manual.
- Saves the change and then displays the next menu item
- Moves to the lower level menu item
Referred to as Enter button in this manual.
Moves to the upper level menu item without saving the change
Referred to as Exit button in this manual.
■ Transitions of screens in setup mode
Refer to the next page LCD screen transitions chart for setup mode.
The flow chart in the following pages show transition of the LCD screen.
Some of the details are not expressed in the chart.
For the details, please refer to the descriptions in "7.2 Setup mode functions" on page 7-10.
7-4
7.1 Setup Mode
(From screen !30)
0
1
T
!
=
0
2
!
=
0
3
F
!
=
0
N
4
o
!
=
0
N
5
o
!
=
0
6
!
=
0
!
A
0
l
S
i
e
n
p
a
r
a
t
g
g
g
c
c
P
r
O
e
n
/
p
O
i
f
c
f
k
a
P
s
i
t
c
/
k
M
i
S
d
p
/
e
S
e
l
d
o
w
/
D
Y
o
e
u
s
b
g
l
1
e
/
2
F
:
e
S
e
t
d
o
h
/
L
Y
e
e
n
s
g
g
t
1
h
/
2
S
k
O
e
n
w
/
O
C
f
i
T
o
h
n
i
c
k
7
C
:
h
S
e
t
h
f
e
c
k
c
o
7
N
I
/
P
1
C
/
2
P
/
r
3
e
/
4
s
/
e
5
t
o
8
a
A
m
b
r
r
S
a
e
s
t
i
?
o
N
n
o
/
Y
e
p
k
p
!
=
0
O
4
f
f
1
/
!
T
0
o
4
p
:
2
!
0
4
-
3
U
n
l
->
t
1
r
/
a
2
s
:
o
F
n
u
i
l
c
l
S
0
U
S
L
r
1
a
0
n
0
g
:
e
m
m
+
o
T
/
h
Y
i
e
c
s
k
n
e
s
s
N
r
O
!
T
0
h
4
i
c
4
k
n
D
e
F
s
s
M
&
o
R
d
o
e
l
l
e
!
0
P
4
i
c
5
k
/
D
P
F
i
c
t
k
i
&
m
F
i
e
n
e
g
d
!
=
0
5
1
0
1
/
L
5
e
/
n
2
g
0
t
1
h
m
m
!
0
8
S
t
1
o
A
/
l
M
a
e
r
s
m
s
a
M
g
o
e
d
p
8
3
2
0
A
0
l
0
a
0
r
0
m
s
h
C
e
N
e
T
t
s
!
=
0
OPERATOR PANEL MENUS
!
=
e
<<Continue on screen !09 on the next page>>
7.1 Setup Mode
7-5
!
P
0
i
9
c
k
A
/
b
B
r
r
a
a
s
k
i
e
o
/
n
P
a
0
N
o
P
r
a
m
p
a
e
l
r
/
S
L
h
e
o
n
r
1
E
1
n
g
L
l
a
i
n
s
g
h
u
/
a
S
g
h
e
o
r
!
=
1
2
W h
F
i
.
t
B
e
a
/
c
B
k
l
g
a
r
c
!
=
1
3
W h
B
i
.
t
B
e
a
/
c
B
k
l
g
a
!
=
1
4
R
F
G
.
/
D
B
r
o
p
/
!
=
1
5
R
B
G
.
/
D
B
r
o
/
!
1
C
6
h
a
P
n
i
g
c
e
k
?
!
=
1
!
=
C
d
N
T
g
t
t
h
o
k
u
n
d
r
c
o
k
u
n
d
-
o
u
t
p
-
o
u
t
r
N
e
o
t
/
r
Y
y
e
s
<<Continue on screen !17 on the next page>>
7-6
7.1 Setup Mode
!
=
0
x
9
x
x
1
x
P
x
i
x
!
=
0
x
9
x
x
2
x
B
x
r
x
!
=
0
x
9
x
x
3
x
P
x
a
x
!
=
0
x
9
x
x
4
x
F
x
r
x
!
=
0
x
9
x
x
5
x
B
x
a
x
!
0
x
9
x
x
6
x
R
e
!
=
1
6
-
1
R
!
=
1
6
-
2
R
c
R
k
e
s
C
e
N
t
T
/
N
o
a
R
k
e
e
s
e
C
t
N
/
T
N
o
d
R
e
C
s
N
e
T
t
/
N
o
o
R
n
e
t
s
e
L
t
a
/
m
N
p
o
c
R
k
e
s
L
e
a
t
m
/
p
N
o
s
N
e
o
t
/
N
e
o
s
w
Y
e
t
2
r
y
S
t
e
p
e
t
4
r
y
T
i
m
e
!
!
1
C
1
C
7
h
8
h
a
a
F
n
M
n
e
g
a
g
e
e
n
e
r
N
d
?
u
?
1
0
9
/
1
S
/
C
2
S
/
I
3
!
f
2
i
0
4
P
6
r
0
o
C
d
8
!
=
2
1
W i
S
d
C
t
S
h
I
!
=
2
2
A
u
I
t
n
o
t
/
!
=
2
1
3
9
2
B
0
a
0
!
S
2
e
4
l
e
I
c
!
=
2
5
N
O
l
N
o
t
/
F
/
r
Y
e
Y
y
e
e
e
s
d
s
/
I
4
D
/
5
/
6
/
7
u
/
c
f
t
i
4
I
9
D
9
0
C
8
B
/
u
1
s
6
b
i
t
e
S
r
C
f
S
a
I
c
/
e
T
P
S
u
/
d
9
6
R
0
a
0
t
/
e
4
8
0
0
m
t
p
r
i
P
n
r
t
e
e
/
r
P
o
s
t
u
n
m
/
e
f
r
f
i
(
n
P
g
o
s
t
)
b
O
!
=
1
7
-
1
R
e
t
1
r
y
S
t
e
p
!
=
1
7
-
2
R
e
t
4
r
y
T
i
m
e
!
=
1
8
-
1
P
1
i
.
c
0
k
t
c
a
r
t
S
S
e
!
=
1
8
-
2
T
3
i
0
m
e
S
e
o
c
u
t
!
=
2
5
-
1
D
i
/
g
i
8
t
s
!
=
2
S
0
t
0
a
0
r
0
t
C
o
u
n
t
0
!
=
2
E
n
m
/
p
O
t
f
y
f
R
e
s
e
t
O
!
=
2
R
e
s
N
e
o
t
/
N
e
o
s
w
Y
5
5
0
0
2
0
5
-
3
5
-
4
7
OPERATOR PANEL MENUS
!
=
a
e
o
<<Continue on screen !26 on the next page>>
7.1 Setup Mode
7-7
I
n
k
g
g
c
c
P
0
o
w
1
8
h
a
B
n
r
g
2
t
9
a
t
I
u
3
N
0
o
r
L
m
2
6
g
g
!
=
2
7
!
2
C
!
S
!
=
!
=
(
x
R
e
1
r
5
i
e
g
?
h
m
s
p
r
a
a
m
l
p
/
x
e
x
s
x
e
)
t
/
N
o
S
a
2
v
0
e
m
i
n
t
N
n
o
e
/
s
Y
s
e
s
i
P
n
o
t
s
e
t
r
/
P
r
e
A
c
l
o
w
n
a
t
y
r
s
o
O
l
n
(To screen !1)
7-8
!
7.1 Setup Mode
!
F
2
2
r
6
8
o
-
n
1
1
t
R
B
:
e
r
0
s
N
e
o
t
/
N
e
o
s
w
Y
i
g
B
h
a
t
c
n
k
e
:
s
s
0
HINT
HINT
The menu screens with dotted line frame appear only when the scanner is in
the Offline setup mode.
Screen 22 and screen 23 appear only when any TPS interface board is
installed.
Screen 24 appears only when both the fi-486PRFR (Front side imprinter)
and the fi-486PRRE (Rear side imprinter) are installed.
Screen 25, Screen 26 and Screen 29 appear when either or both of the fi486PRFR and the fi-486PRRE are installed.
7
OPERATOR PANEL MENUS
7.1 Setup Mode
7-9
7.2 Setup mode functions
There are 30 items in setup mode as shown in the following.
LCD
display
Double Feed
Descriptions
Specifies the double-feed
detection mode based on:
1: Document overlapping /
thickness
2: Document overlapping /
thickness+ Brake roller
rotation amount
Selectable
parameters
Default
Mode
Online
Offline
Yes
No/Yes
1: Overlapping /
Thickness
2: Overlapping /
Thickess+ Brake
roller
Avail- Available
able
Settings via the
PC have the
priority.
Settings via the
PC have the
priority.
Length Check Specifies the double-feed
detection based on the
document length deviation.
There are 3 selections for the
acceptable length deviation
tolerance as shown right.
No/Yes
Yes:
10/15/20mm
(0.4/ 0.6/ 0.8 in.)
(Tolerance)
No
Avail- Available
able
IPC
Pre-Set
No
1:
2:
3:
4:
5:
No
Avail- Available
able
7-10
The scan parameters are set
with recommended values
automatically. There are 5
choices as shown right.
7.2 Setup mode functions
Remarks
LCD
display
Descriptions
Selectable
parameters
Default
Stop/Message
10,000 to
2,560,000 sheets
Specifies the scanners
operation when consumables
replacement occurs: stop
scanning or message display
only. Also specifies the
consumable replacement
message timing.
Abrasion
Counter
Clear the consumable counters (Abrasion counter)
Manual Feed
Specifies the pick start time
from the time document is
manually set.
0.2 to 29.8 sec
Remarks
Online
Offline
Stop
300,000
Available
Available
The
replacement
timing
increment/
decrement by
10,000 sheets.
-
Not
Available
Available
-
1.0 sec
Available
Available
-
30 sec
Specifies the waiting time from 1, 5, 10, 20, 30,
the execution of read command 40, 50, 60, 70, 80,
on PC to document insertion. 90, 100, 110, 120,
180, 240, 255 sec
7.2 Setup mode functions 7-11
7
OPERATOR PANEL MENUS
Abrasion
Alarm
Mode
LCD
display
Descriptions
Selectable
parameters
Skew Check
Specifies if skew detection is
enabled.
Separation
Specifies the Brake roller force Thick
appropriate for the document
thickness
Medium Thick
Default
Mode
Remarks
Online
Offline
Off
Available
Available
Settings via the
PC have the
priority.
Medium
Available
Available
-
Normal
Available
Available
-
B.Background Specifies the background color White /
(Black or White) for scanning. Black
(Front)
White
Available
Available
Settings via the
PC have the
priority.
B.Background Specifies the background color White /
(Black or White) for scanning. Black
(Back)
White
Available
Available
Settings via the
PC have the
priority.
On/Off
Medium
Medium Thin
Thin
Paper Length
7-12
Set when scanning the
Normal /
document equal or shorter than Short
length 80mm (3.15”).
7.2 Setup mode functions
LCD
display
Pre-pick
Descriptions
Selectable
parameters
F.Drop-out
Remarks
Offline
Available
Available
Settings via the
PC have the
priority.
Available
Available
The throughput
of the scanner
will be affected.
Specify the Pick motor rotation Retry Step
time (Retry Step) and number :1 - 7
of retries (Retry Time).
Retry Time
:1 - 7
Retry Step Available
:2
Available
-
Retry Step
Specify the Feed motor
rotation time (Retry Step) and :1 - 7
number of retries (Retry Time).
Retry Time
:1 - 7
Retry Step Available
:1
Available
-
Specifies the front page
dropout color for a
monochrome scan.
G
Available
Settings via the
PC have the
priority.
Enable or disable pre-pick
operation, the picking of a
document prior to actual
feeding. (increase scan
throughput)
On / Off
R
G
B
On
Fast
Retry
Time
:4
Retry
Time
:4
Available
7.2 Setup mode functions 7-13
7
OPERATOR PANEL MENUS
Feed retry
Mode
Online
Picking speed Specify the Pick roller rotation Fast /
speed
Mid /
Slow
Pick retry
Default
LCD
display
Descriptions
Selectable
parameters
Default
Mode
Online
Offline
Remarks
B.Drop-out
Specifies the back page
dropout color for a
monochrome scan.
R
G
B
G
Available
Available
Brightness
Adjust the Front/Back
Brightness to compensate for
the grayscale level differences
between the CCDs.
-6 to +6
0
Available
Available
SCSI ID
Specifies SCSI ID of the
scanner.
0 to 7
5
Not
Available
Available
New SCSI ID
valid after
power cycle.
Product ID
Specifies the scanner product
ID.
fi4860C /
fi4990C /
M4099D /
M3099G
fi4860C
Not
Available
Available
New setting
valid after
power cycle.
SCSI Bus
Specifies the SCSI data bus
width, 8bit or 16 bit.
16bit/
8bit
16bit
Not
Available
Available
New setting
valid after
power cycle.
Interface
Auto /
Specifies the interface to use
when an optional or third party SCSI /
interface board is installed in
TPS
the TPS (Third Party Slot).
Auto
Not
Available
Available
7-14
7.2 Setup mode functions
Settings via the
PC have the
priority.
LCD
display
Descriptions
Selectable
parameters
Default
Not
Available
Available
New setting
valid after
power cycle.
Available
Available
-
Numbering
: On / Off
Numberin Availg
able
: Off
Available
Settings via the
PC have the
priority.
Digits
:5/8
Digits
:5
Initial No.:
5digit:0-99999
8digit:
0-16777215
Initial No.:
00000
Reset at hopper
empty: On/Off
Reset at
hopper
empty: On
-
-
Available
-
Imprinter
When both fi-486PRFR (Front Pre / Post
side/Pre-print) and fi486PRRE (Rear side/Postprint) are installed, specifies
which one to setup.
-
Numbering
When either fi-486PRFR
(Front side/Pre-print) and fi486PRRE (Rear side/Postprint) is installed, set the
numbering parameters.
Shows the remaining ink.
Reset remaining ink amount
counter when the Print
cartridge is replaced.
Available
7.2 Setup mode functions 7-15
7
OPERATOR PANEL MENUS
Offline
9600
Ink
Remarks
Online
Specifies the control data
19200 /
transfer rate for TPS interface. 9600 /
4800 /
2400
Baud Rate
Mode
LCD
display
Descriptions
Selectable
parameters
Default
Mode
Online
Offline
Power Save
Specifies the time before
entering Power save mode.
5 to 60minutes
15 minutes Available
Available
Language
Specifies the language to use
for Operator panel display.
Japanese
(Katakana) /
English
-
Available
Available
Imprinter
Status
Shows the installed imprinter
type.
-
-
Available
Available
Normal/
AlwaysON
Normal
Available
Available
Lamp control Specifies whether or not to
keep the lamp turned on.
7-16
7.2 Setup mode functions
Remarks
7.3 Setup Mode Details
1. Setting the document separation force
1) Press
(Next button) or
(Previous button) and let the scanner show
<Screen1>.
<Screen1>
!
=
0
1
T
h
S
i
e
n
p
a
r
a
t
J
J
J
F
F
o
h
n
i
c
k
(Right arrow button) and
The blinking item is the one selected.
HINT
(Right arrow button) moves the blinking from (5) to (1).
(Left arrow button) moves the blinking from (1) to (5).
(1)
-
Document thickness: Thick
(2)
-
Document thickness: Medium thick
(3)
-
Document thickness: Medium
(4)
-
Document thickness: Medium thin
(5)
-
Document thickness: Thin
3) Press
Press
(Enter button) to confirm the setting.
(Exit button) at the end and the LCD redisplays [Ready] screen.
7.3 Setup Mode Details 7-17
7
OPERATOR PANEL MENUS
2) At <Screen1>, press
(Left arrow button) or
select the appropriate document thickness.
i
T
If the following error occurs frequently, change the setting by
referring to the explanation on the table.
- Double-feed
- Mis-pick
- Paper Jam1
HINT
Setting
Thick
Document separation force
Mis-pick or
Paper jam1 occurs frequently.
Make the document
separation force stronger.
Make the document separation
force weaker.
Strong
Medium Thick Medium strong
7-18
Double-feed occurs
frequently.
Medium
Average (Factory
default)
Medium Thin
Medium weak
Thin
Easy weak
7.3 Setup Mode Details
2. Setting Pre-pick
1) Press
(Next button) or
(Previous button) and let the scanner show
<Screen2>.
<Screen2>
!
=
0
2
P
2) At <Screen2>, to enable Pre-pick, press
To disable Pre-pick, press
Press
screen.
e
n
/
p
O
i
f
c
f
k
(Left arrow button) and select [On].
7
(Right arrow button) and select [Off].
(Enter button) to confirm the setting.
(Exit button) at the end and the LCD display goes back to [Ready]
7.3 Setup Mode Details 7-19
OPERATOR PANEL MENUS
3) Press
r
O
3. Setting Pick Speed
1) Press
(Next button) or
(Previous button) and let the scanner show
<Screen3>.
<Screen3>
!
=
0
3
F
a
P
s
i
t
c
/
k
M
2) At <Screen3>, press
(Left arrow button) or
select Pick roller rotation speed.
i
S
d
p
/
e
S
e
l
d
o
w
(Right arrow button) and
The blinking item is the one selected.
HINT
3) Press
Press
screen.
(Enter button) to confirm the setting.
(Exit button) at the end and the LCD display goes back to [Ready]
Pick roller rotation speed should be set Slow for scanning thin or soft documents, these documents tend to cause a Mis-pick to occur.
HINT
Picking speed
Fast (Factory default)
When Mis-pick occurs frequently
Decreases the Pick speed
Mid
Slow
When the Pick speed is set at "Mid" or "Slow", the scanner will slow down.
HINT
7-20
7.3 Setup Mode Details
4. Setting Double-feed detection (document overlapping/thickness)
1) Press
(Next button) or
(Previous button) and let the scanner show
<Screen4>.
<Screen4>
!
=
0
N
4
o
/
D
Y
o
e
u
s
b l
J 1
e
/
2
F
:
e
S
e
t
d
o
p
By pressing
(Right arrow button), the selection moves from (1) to (3).
By pressing
(Left arrow button), the selection moves from (3) to (1).
(1) [No] is blinking:
Document overlapping and thickness
are not checked.
(2) [Yes] and [1] are blinking:
Document overlapping and thickness
are checked.
However, the scanning continues even if
Double-feed is detected and an error
message is displayed on the LCD.
(3) [Yes] and [2: Stop] are blinking:
Document overlapping and thickness
are checked.
When a double-feed is detected, the
scanning stops. Then the error is
reported to the PC.
To disable the Double-feed detection, select [No] and press
(Enter button).
The blinking item is the one selected.
HINT
7.3 Setup Mode Details 7-21
7
OPERATOR PANEL MENUS
2) At <Screen4>, by pressing
(Left arrow button) or
(Right arrow button),
Double-feed detection by document thickness can be enabled or disabled. (A
Double-feed is checked by the difference in the amount of ultrasonic waves
and/or the light penetrating through the paper.) In this screen, you can enable
or disable the Double-feed detection and set the detection mode and select
error processing.
3) At <Screen 4-1> you can enable or disable the Double-feed detection or
configure the detection modes by pressing
(Right arrow button) or
(Left
arrow button).
<Screen4-1>
!
=
0
O
4
f
f
1
/
O
U
n
t
l
-> 1
r
/
a
2
s
:
o
F
n
u
i
l
By pressing
(Right arrow button), the selection moves from (1) to (3).
By pressing
(Left arrow button), the selection moves from (3) to (1).
c
l
(1) [Off] is blinking:
Document overlapping is not checked.
(2) [On] and [1] are blinking:
Document overlapping is checked for
the range set at step 4). This mode is
used for preventing mis-detection when
scanning documents that are pasted
photos, etc.
(3) [On] and [2: Full] are blinking:
Document overlapping is checked for
the whole area of the
documents.(Default setting)
4) At <Screen 4-2> you can set the detection range for Double-feed by checking
document overlapping. Press
(Left arrow button) or
(Right arrow button)
to set the start and end positions for the detection.
<Screen 4-2>
!
T
0
o
4
p
:
2
S
0
S
L
:
r
1
a
0
n
0
g
e
m
m
(1) [Top] is blinking:
The start position for the detection is set.
(2) [L] is blinking:
The detection is range set.
Press
(Next button) or
(Previous button) to increase/decrease the value of
the selected item. To enable the settings, press
7-22
U
7.3 Setup Mode Details
(Enter button).
The available ranges of detection are as follows:
Top: 0 (default), 50, 100, 150, 200 (Unit : mm)
L: 100 (default), 150, 200 (Unit : mm)
5) Besides the Double-feed detection by checking paper overlapping (the amount
of ultrasonic waves), you can enable or disable the detection by checking paper
thickness (the amount of light) at <Screen 4-3>. Press
(Left arrow button) or
<Screen 4-3>
!
0
4
3
-
N
+
o
T
/
h
Y
i
e
c
s
k
n
e
s
s
(1) [Yes] is blinking:
The Double-feed deteciton by checking
paper thickness is executed.
(2) [No] is blinking:
The Double-feed deteciton by checking
paper thickness is not executed.
Press
(Enter button) to enable the setting.
6) When the LCD is showing (2) or (3), pressing
display to <Screen 4-4>.
(Enter button) changes LCD
<Screen4-4>
!
=
0
4
-
4
T
h
D
i
F
c
k
7) At <Screen4-4>, by pressing
(Left arrow button) or
you can select the detection mode.
M
n
o
e
d
s
e
s
(Right arrow button),
Each time
(Left arrow button) or
(Right arrow button) is pressed, LCD
displays [Thickness] and [Thickness & Roller] alternately.
<Screen4-4>
7.3 Setup Mode Details 7-23
OPERATOR PANEL MENUS
(Right arrow button) to enable or disable the detection by checking paper
thickness.
7
!
T
0
h
4
i
c
4
k
n
D
e
F
s
s
M
&
o
R
d
o
e
l
l
e
+
r
(1) [Thickness] is blinking:
Double-feed is detected by light amount
transmitted through paper.
(2) [Thickness & Roller] is
blinking:
Double-feed is detected based on the light
amount transmitted through paper and
Brake roller rotation amount.
(3) [+] is blinking:
Also the double-feed detection by checking
paper overlapping is executed.
By pressing
(Enter button), LCD display changes to <Screen4-5>.
<Screen4-5>
!
0
P
4
i
c
5
k
/
D
P
F
i
c
8) At <Screen4-5>, by pressing
(Left arrow button) or
the detection timing can be selected.
(1) [Pick] is blinking:
t
k
i
&
m
F
i
e
n
e
g
d
(Right arrow button),
Double-feed is checked by the document pick
timing.
(2) [Pick & Feed] is blinking: Double-feed is checked by the document pick
timing and during feeding.
9) Press
Press
HINT
7-24
(Enter button) to confirm the setting.
(Exit button), and the LCD display goes back to [Ready] screen.
Double-feed detection accuracy increases when all the overlapping, thickness and length of documents are checked.
7.3 Setup Mode Details
ATTENTION
ATTENTION
When a double-feed is detected and the scanning operation is stopped, the
last documents in the hopper or the one ahead of it might have been double
fed.
Depending on the document type, there are cases when double-feed can not
be detected by paper thickness.
7
OPERATOR PANEL MENUS
7.3 Setup Mode Details 7-25
5. Setting Double-feed detection (by document length)
1) Press
(Next button) or
(Previous button) and let the scanner show
<Screen5>.
<Screen5>
!
=
0
N
5
o
/
L
Y
e
e
n
s
g t
J 1
h
/
2
C
:
h
S
e
t
c
o
k
p
2) At <Screen5>, by pressing
(Left arrow button) or
(Right arrow button),
Double-feed detection by document length can be enabled or disabled.
By checking the document length for partially over lapped sheets that are fed
together. In this screen, you can specify if the amount of length checking is
done, set the detection conditions, and select the error processing.
By pressing
(Right arrow button), selection moves from (1) to (3).
By pressing
(Left arrow button), selection moves from (3) to (1).
(1) [No] is blinking:
Document length is not checked.
(2) [Yes] and [1] are blinking:
Document length is checked.
However, scanning continues even if
Double-feed is detected and the error
message is displayed on the LCD.
(3) [Yes] and [2: Stop] are blinking:
Document length is checked.
When double-feed is detected, scanning
stops. Then the error is reported to the
PC.
If you would like to disable the Double-feed detection, select [No] and press
(Enter button).
The blinking item is the one selected.
HINT
7-26
7.3 Setup Mode Details
3) In case of (2) or (3), by pressing
<Screen5-1>.
(Enter button), LCD display changes to
<Screen5-1>
!
=
0
5
1
0
1
/
1
L
5
e
/
n
2
4) At <Screen5-1>, by pressing
(Left arrow button) or
the document length can be specified.
g
0
t
h
m
m
(Right arrow button),
(Right arrow button), selection moves from (1) to (3).
By pressing
(Left arrow button), selection moves from (3) to (1).
(1) [10] is blinking: The document length difference below 10mm is not
detected as an error.
(2) [15] is blinking: The document length difference below 15mm is not
detected as an error.
(3) [20] is blinking: The document length difference below 20mm is not
detected as an error.
5) Press
Press
(Enter button) to confirm the setting.
(Exit button), and the LCD display goes back to [Ready] screen.
7.3 Setup Mode Details 7-27
OPERATOR PANEL MENUS
By pressing
7
6. Setting Skew Check
1) Pressing
(Next button) or
<Screen6>.
(Previous button) and let the LCD show
<Screen6>
!
=
0
6
S
k
O
e
n
w
/
O
C
f
2) If you want to enable Skew check at <Screen6>, press
and select [On].
To disable Skew-check, press
press
3) Press
Press
screen.
7-28
h
f
e
c
k
(Left arrow button),
(Right arrow button) and select [Off] then
(Enter button).
(Enter button) to confirm the setting.
(Exit button) at the end and the LCD display goes back to [Ready]
7.3 Setup Mode Details
7. Setting IPC pre-set
1) Pressing
(Next button) or
<Screen7>.
(Previous button) and let the LCD show
<Screen7>
!
=
0
7
N
o
I
/
P
1
C
/
2
P
/
r
3
e
/
2) At <Screen7>, the preset items can be selected by pressing
s
/
e
5
t
(Left arrow
(Right arrow button).
The blinking item is the one selected.
HINT
3) Press
Press
screen.
7
(Enter button) to confirm the setting.
(Exit button) at the end and the LCD display goes back to [Ready]
7.3 Setup Mode Details 7-29
OPERATOR PANEL MENUS
button) or
4
HINT
When scanning in Binary mode (Line art), document type and a suitable preset pattern relationship is shown as follows:
− The horizontal axis shows the darkness/color of the background against
the text/lines on the documents.
− The vertical axis shows the darkness of the text and lines on the
documents.
Document type and IPC preset pattern
Background darkness
Normal 
Text
Darkness
Normal
1: Normal
Background
and normal
darkness text
i
Light
2: Mid darkness
background and
light text
Background color
Dark
7.3 Setup Mode Details
Green
3: Dark back-ground
and
normal darkness
text
*1 to 5 indicates IPC pre-set pattern number.
7-30
Red
4: Red back- 5: Green
ground and back-ground
light text
and light
text
Blu
e
HINT
This setting is invalid in grayscale mode or in color mode.
Pre-sets are valid only in binary scan mode.
The following table shows validity of each scan parameter when using IPC
pre-set in Offline mode.
7
Validity of scan parameter
Invalid
Resolution
X
X
-
-
-
-
X
X
Gamma
Pattern
Contrast
Document
selection
Valid
Invalid
Line
art/
Photos
Halftone
Auto
separation
DTC
Document
sizes
Portrait/
Landscape
Cropping
-
X
X
X
X
-
-
-
Reverse
image
Image
empha
sis
Outline
Extrac
tion
Simplified
DTC
X
-
-
-
X
-
-
-
-
X
X
X
-
X
X
X
7.3 Setup Mode Details 7-31
OPERATOR PANEL MENUS
Valid
Scan
mode
8. Setting Consumables Replacement Message
1) Pressing
(Next button) or
<Screen8>.
(Previous button) and let the LCD show
<Screen8>
!
A
0
l
8
a
r
A
m
b
r
S
a
e
s
t
i
?
o
N
n
o
/
Y
e
s
2) At <Screen8> , to change Consumables replacement message setup (Abrasion
Alarm), press
(Right arrow button) and select [Yes].
The blinking item is the one selected.
HINT
Press
(Enter button) to confirm the selection. <Screen8-1> appears on
LCD.
If Consumables replacement message setup change is not required, select [No]
and press
(Enter button).
<Screen8-1>
!
7-32
7.3 Setup Mode Details
0
8
S
t
1
o
p
A
/
l
M
a
e
r
s
m
s
a
M
g
o
e
d
e
3) At <Screen8-1>, press
(Left arrow button) or
select consumable error process.
(1) [Stop] is blinking:
(Right arrow button) to
When the consumables replacement limit is
reached, the Consumables replacement message (Abrasion alarm) is shown on the LCD and
scanning stops.
By pressing
(Enter button), <Screen8-2> appears on the LCD.
<Screen8-2>
!
=
0
8
3
2
0
0
A
0
l
0
a
0
r
m
s
h
C
e
N
e
T
t
4) At <Screen8-2>, specify the number of scans to get Consumables replacement
message.
Each time
10,000.
(Left arrow button) is pressed, the counter value decrements by
Each time
10,000.
(Right arrow button) is pressed, the counter value increments by
5) Press
Press
(Enter button) to confirm the setting.
(Exit button) , and the LCD display goes back to [Ready] screen.
7.3 Setup Mode Details 7-33
7
OPERATOR PANEL MENUS
(2) [Message] is blinking: When the consumables replacement limit is
reached, the Consumables replacement message (Abrasion alarm) is shown on the LCD but
the scanning continues.
9. Abrasion counter (Abrasion CNT) reset
1) Pressing
(Next button) or
<Screen9>.
(Previous button) and let the LCD show
<Screen9>
!
P
0
i
9
c
k
A
/
b
B
r
r
a
a
s
k
i
e
o
/
n
P
a
C
d
N
T
2) At <Screen9>, select the Abrasion counter to reset.
The blinking item is the one selected.
HINT
You can select a counter from the following.
(1) [Pick] is blinking:
Pick roller counter (Pick CNT) can be reset.
(2) [Brake] is blinking:
Brake roller counter (Brake CNT) can be reset.
(3) [Pad] is blinking:
Pad counter (Pad CNT) can be reset.
(4) [F.Lamp] is blinking: Front-side lamp counter (Front Lamp) can be reset.
(5) [B.Lamp] is blinking: Back-side lamp counter (Back Lamp) can be reset.
7-34
By pressing
(Right arrow button), selection moves from (1) to (5).
By pressing
(Left arrow button), selection moves from (5) to (1).
7.3 Setup Mode Details
3) By pressing
(Enter button), LCD display changes to <Screen9-1>,
<Screen9-2>, <Screen9-3>, <Screen9-4>, or <Screen9-5> depending on the
selection at <Screen9>.
When [Pick] is selected:
<Screen9-1>
!
=
0
x
9
x
x
P
x
i
x
2
x
B
x
r
x
3
x
P
x
a
x
4
x
F
x
r
x
5
x
B
x
a
x
c
R
k
e
s
C
e
N
t
T
/
N
o
a
R
k
e
e
s
e
C
t
N
/
T
N
o
d
R
e
C
s
N
e
T
t
/
N
o
o
R
n
e
t
s
e
L
t
a
/
m
N
p
o
c
R
k
e
s
L
e
a
t
m
/
p
N
o
When [Brake] is selected:
<Screen9-2>
!
=
0
x
9
x
x
When [Pad] is selected:
<Screen9-3>
!
=
0
x
9
x
x
When [F Lamp] is selected:
<Screen9-4>
!
=
0
x
9
x
x
When [B Lamp] is selected:
<Screen9-5>
!
=
0
x
9
x
x
[XXXXXX] indicates each Abrasion counter value.
HINT
7.3 Setup Mode Details 7-35
7
OPERATOR PANEL MENUS
1
x
4) At <Screen9-1> , <Screen9-2>, <Screen9-3>, <Screen9-4> or <Screen9-5>, to
reset the corresponding counter, press
(Left arrow button) and select
[Reset].
Press
(Enter button) to confirm the selection, then <Screen9-6> is
displayed.
If you do not want to reset the counter, select [No] and press
button).
(Enter
<Screen9-6>
!
0
x
9
x
x
6
x
R
e
s
N
e
o
t
/
Y
N
e
o
s
w
[XXXXXX] is the counter value of the selected consumable.
HINT
− Pick roller counter
− Brake roller counter
− Pad counter
− Front-side lamp counter (lamp-on time)
− Back-side lamp counter (lamp-on time)
5) If you are sure to reset, select [YES] and press
To cancel Reset, select [No] and press
Press
7-36
(Enter button).
(Enter button).
(Exit button) and the LCD display goes back to [Ready] screen.
7.3 Setup Mode Details
10. Setting Short document scan mode(Paper Length setup)
1) Press
(Next button) or
<Screen10> .
(Previous button) and let the LCD display
<Screen10>
!
=
1
0
N
o
P
r
a
m
p
a
e
l
r
/
S
L
h
e
o
n
r
g
t
t
h
The blinking item is the one selected.
HINT
(1) [Normal] is blinking: This mode is for scanning documents longer than
80mm or 3.15inches.
(2) [Short] is blinking:
3) Press
Press
screen.
This mode is for scanning documents which length
is 80mm or less, 3.15inches or less.
(Enter button) to confirm the setting.
(Exit button) at the end and the LCD display goes back to [Ready]
7.3 Setup Mode Details 7-37
OPERATOR PANEL MENUS
2) At <Screen10>, press
(Left arrow button) or
(Right arrow button) and
select the proper setting for the document to scan.
7
11. Setting Language
1) Press
(Next button) or
<Screen11> .
(Previous button) and let LCD display
<Screen11>
!
=
1
E
1
n
2) Press
(Left arrow button) or
language for LCD display.
3) Press
Press
screen.
7-38
g
L
l
a
i
n
s
g
h
u
/
a
g
e
(Right arrow button) and select the
(Enter button) to confirm the setting.
(Exit button) at the end and the LCD display goes back to [Ready]
7.3 Setup Mode Details
12. Setting Front-side background color
1) Press
(Next button) or
<Screen12>.
(Previous button) and let LCD display
<Screen12>
!
=
1
2
W h
F
i
.
t
B
e
a
/
c
B
k
l
g
a
To set the background color to black, press
[Black].
3) Press
Press
screen.
o
k
u
n
d
7
(Left arrow
(Right arrow button) and select
(Enter button) to confirm the setting.
(Exit button) at the end and the LCD display goes back to [Ready]
7.3 Setup Mode Details 7-39
OPERATOR PANEL MENUS
2) At <Screen12>, to set the background color to white, press
button) and select [White].
r
c
13. Setting Back-side background color
1) Press
(Next button) or
(Previous button) and let LCD display
<Screen13>.
<Screen13>
!
=
1
3
W h
B
i
.
t
B
e
a
/
c
B
k
l
g
a
2) At <Screen12>, to set the background color to white, press
button) and select [White].
To set the background color to black, press
[Black].
3) Press
Press
screen.
7-40
r
c
o
k
u
n
d
(Left arrow
(Right arrow button) and select
(Enter button) to confirm the setting.
(Exit button) at the end and the LCD display goes back to [Ready]
7.3 Setup Mode Details
14. Setting Front-side dropout color
1) Press
(Next button) or
<Screen14>.
(Previous button) and let LCD display
<Screen14>
!
=
1
4
R
/
F
G
.
/
D
B
r
p
-
o
u
t
(Right arrow button) and
The blinking item is the one selected.
HINT
3) Press
Press
screen.
7
(Enter button) to confirm the setting.
(Exit button) at the end and the LCD display goes back to [Ready]
7.3 Setup Mode Details 7-41
OPERATOR PANEL MENUS
2) At <Screen14>, press
(Left arrow button) or
select the color to drop out.
o
15. Setting Back-side dropout color
1) Press
(Next button) or
<Screen15>.
(Previous button) and let LCD display
<Screen15>
!
=
1
5
R
/
B
G
.
/
D
B
r
2) At <Screen15>, press
(Left arrow button) or
select a color to drop out.
o
p
-
o
u
t
(Right arrow button) and
The blinking item is the one selected.
HINT
3) Press
Press
screen.
7-42
(Enter button) to confirm the setting.
(Exit button) at the end and the LCD display goes back to [Ready]
7.3 Setup Mode Details
16. Setting Pick retry
1) Press
(Next button) or
<Screen16>.
(Previous button) and let LCD display
<Screen16>
!
1
C
6
h
a
P
n
i
g
c
e
r
N
k
?
e
o
t
/
r
Y
y
e
s
2) At <Screen16>, to change pick motor’s pick operation time and the number of
If the change is not required, select [No] and press
(Enter
(Enter button).
<Screen16-1>
!
=
1
6
1
-
R
e
t
2
r
y
S
t
e
p
The blinking item is the one selected.
HINT
3) At <Screen16-1>, pick motor's pick operation time can be specified. Longer
pick operation time makes the pick feed amount bigger.
Pressing
(Left arrow button) makes the pick operation time shorter.
Pressing
(Right arrow button) makes the pick operation time longer.
Press
(Left arrow button) or
(Right arrow button), and select the setting.
The range of the pick motor retry steps is 1 to 7.
Press
(Enter button) to confirm the selection. <Screen16-2> is displayed.
<Screen16-2>
!
=
1
6
-
2
R
e
t
4
r
y
T
i
m
e
7.3 Setup Mode Details 7-43
OPERATOR PANEL MENUS
retries, press
(Right arrow button) and select [Yes]. Press
button) to confirm the selection. <Screen16-1> is displayed.
7
4) At <Screen16-2>, specify the number of pick retries. By pressing
arrow button), the number of retries decreases. By pressing
button), the number of retries increases.
Press
(Left arrow button) or
(Left
(Right arrow
(Right arrow button), and select the setting.
The number of the pick retries can be set between 1 to 7 times.
5) Press
Press
screen.
7-44
(Enter button) to confirm the setting.
(Exit button) again and the LCD display goes back to [Ready]
7.3 Setup Mode Details
17. Setting Feed retry
1) Press
(Next button) or
<Screen17>.
(Previous button) and let LCD display
<Screen17>
!
1
C
7
h
a
F
n
e
g
e
e
d
?
r
N
e
o
t
/
r
Y
y
e
s
Press
(Enter button) to confirm the selection. <Screen17-1> is displayed.
If the change is not required, select [No] and press
(Enter button).
<Screen17-1>
!
=
1
7
1
-
R
e
t
1
r
y
S
t
e
p
The blinking item is the one selected.
HINT
3) At <Screen17-1>, feed motor rotation time can be specified. Longer feed
operation time makes the feed amount bigger.
Pressing
(Left arrow button) makes the feed motor operation time shorter.
Pressing
(Right arrow button) makes the feed motor operation time longer.
Press
(Left arrow button) or
(Right arrow button), and select the setting.
The feed motor rotation step range is 1 to 7 steps.
Press
(Enter button) to confirm the selection. <Screen17-2> is displayed.
<Screen17-2>
!
=
1
7
-
2
R
e
t
4
r
y
T
i
m
e
7.3 Setup Mode Details 7-45
OPERATOR PANEL MENUS
2) At <Screen17>, to change Feed motor operation time and the number of
retries, press
(Right arrow button) and select [Yes].
7
4) In <Screen17-2>, specify the number of retries. By pressing
(Left arrow
button), the number of retry decreases. By pressing
(Right arrow button),
the number of retries increases. The number of the feed retries can be set
between 1 to 7 times.
Press
5) Press
Press
7-46
(Left arrow button) or
(Right arrow button), and select the setting.
(Enter button) to confirm the setting.
(Exit button) , and the LCD display goes back to [Ready] screen.
7.3 Setup Mode Details
18. Setting Manual Feed mode
1) Press
(Next button) or
<Screen18>.
(Previous button) and let LCD display
<Screen18>
!
1
C
8
h
a
M
n
a
g
n
e
u
?
a
l
N
o
e
Y
e
e
d
s
7
(Right arrow
The blinking item is the one selected.
HINT
Press
(Enter button) to confirm the selection then the LCD display
changes to <Screen18-1>.
If the change is not necessary, select [No] and press
(Enter button).
<Screen18-1>
!
=
1
8
-
1
P
1
i
.
c
0
k
S
S
e
t
c
a
r
t
3) At <Screen18-1>, specify the time to start pick from the manual setting of the
document (Start time).
By pressing
(Left arrow button), the pick start time decreases.
By pressing
(Right arrow button), the pick start time increases.
The pick start time can be specified to be 0.2 to 29.8 seconds.
Pick start time can be specified by the unit of 0.2 second.
HINT
7.3 Setup Mode Details 7-47
OPERATOR PANEL MENUS
2) At <Screen18>, if the setting change is required, press
button) and select [Yes].
F
/
Press
(Enter button) then <Screen18-2> is displayed.
<Screen18-2>
!
=
1
8
-
2
T
3
i
0
m
e
S
e
o
c
u
t
4) At <Screen18-2>, specify the wait time (i.e. the time from the PC issues scan
command to time out) for manual setting of document.
By pressing
(Left arrow button), the wait time becomes shorter.
By pressing
(Right arrow button), the wait time becomes longer. .
The wait time can be specified as 1, 5, 10, 20, 30, 40, 50, 60, 70, 80, 90, 100,
110, 120, 180, 240, or 255 sec.
5) Press
Press
7-48
(Enter button) to confirm the setting.
(Exit button) and the LCD display goes back to [Ready] screen.
7.3 Setup Mode Details
19. Setting of SCSI ID
1) Press
(Next button) or
<Screen19>.
(Previous button) and let LCD display
<Screen19>
!
=
1
0
9
/
1
S
/
C
2
S
/
I
3
/
I
4
5
/
6
/
7
(Right arrow button)
The blinking item is the one selected.
HINT
3) Press
Press
screen.
7
(Enter button) and make the setting valid.
(Exit button) at the end and the LCD display goes back to [Ready]
Changed SCSI ID becomes valid after the scanner power is cycled.
HINT
7.3 Setup Mode Details 7-49
OPERATOR PANEL MENUS
2) At <Screen19>, press
(Left arrow button) or press
to select SCSI ID number.
D
/
20. Setting of Product ID(Scanner model number)
1) Press
(Next button) or
<Screen20>.
(Previous button) and let LCD display
<Screen20>
!
f
2) At <Screen20>, press
select Product ID.
2
i
0
4
8
P
6
r
0
o
C
d
(Left arrow button) or
u
/
c
f
t
i
4
I
9
D
9
0
C
(right arrow button) and
The blinking item is the one selected.
HINT
The following are the selectable Product IDs.
(1) fi4860C
(2) fi4990C
(3) M4099D
(4) M3099G
By pressing
(Left arrow button), selection moves from (4) to (1).
By pressing
(Right arrow button), selection moves from (1) to (5).
Usually, Product ID does not need to be changed.
HINT
3) Press
Press
screen.
7-50
(Enter button) to confim the setting.
(Exit button) at the end and the LCD display goes back to [Ready]
7.3 Setup Mode Details
21. Setting SCSI bus width
1) Press
(Next button) or
<Screen21>.
(Previous button) and let LCD display
<Screen21>
!
=
2
1
W i
S
d
C
t
S
h
I
8
B
/
u
1
s
6
If SCSI-2 (50pin) interface is used, press
i
t
(Right arrow
(Left arrow button) and select [8].
The blinking item is the one selected.
HINT
3) Press
Press
screen.
7
(Enter button) to confirm the setting.
(Exit button) at the end and the LCD display goes back to [Ready]
If 16 bit bus width data transfer is prohibited, specify 8 bit.
ATTENTION
7.3 Setup Mode Details 7-51
OPERATOR PANEL MENUS
2) At <Screen21>. If Wide SCSI (68pin) interface is used, press
button) and select [16].
b
22. Setting Interface
1) Press
(Next button) or
<Screen22>.
(Previous button) and let LCD display
<Screen22>
!
=
2
2
A
u
I
t
n
o
t
/
e
S
2) At <Screen22>, press
(Left arrow button) or
select the type of interface.
r
C
f
S
a
I
c
/
e
T
P
S
(Right arrow button), and
The blinking item is the one selected.
HINT
Available interface settings are as follows:
(1) [Auto] is blinking:
If an interface board, either from third party or
optional, is installed in TPS, this interface is used. If
not, SCSI interface is used.
(2) [SCSI] is blinking: SCSI interface is used. The interface on TPS is disregarded.
(3) [TPS] is blinking:
By pressing
(Left arrow button), selection moves from (3) to (1).
By pressing
(Right arrow button), selection moves from (1) to (3).
3) Press
Press
screen.
7-52
TPS interface is used. The SCSI interface is disregarded.
(Enter button) to confirm the setting.
(Exit button) at the end and the LCD display goes back to [Ready]
7.3 Setup Mode Details
23. Setting Baud rate of TPS interface
1) Press
(Next button) or
<Screen23>.
(Previous button) and let LCD display
<Screen23>
!
=
3
9
2
B
0
a
0
u
/
d
9
(Left arrow button) or
6
R
0
a
0
t
/
e
4
8
0
0
(right arrow button) and
The blinking item is the one selected.
HINT
Baud rates available are as follows:
(1) 19200 bps
(2) 9600 bps
(3) 4800 bps
(4) 2400 bps
By pressing
(Left arrow button), selection moves from (4) to (1).
By pressing
(Right arrow button), selection moves from (1) to (4).
Baud rate at 9600 bps is recommended.
HINT
3) Press
Press
screen.
7
OPERATOR PANEL MENUS
2) At <Screen23>, press
select Baud rate.
2
1
(Enter button) to confirm the setting.
(Exit button) at the end and the LCD display goes back to [Ready]
7.3 Setup Mode Details 7-53
24. Selection of Imprinter
1) Press
(Next button) or
(Previous button) and let LCD display
<Screen24>.
<Screen24>
!
S
2
e
4
l
e
I
c
m
t
p
r
2) At <Screen24>, press (Left arrow button) or
select the imprinter to setup.
i
P
n
r
t
e
e
/
r
P
o
s
t
(Right arrow button) and
The blinking item is the one selected.
HINT
3) Press
Press
screen.
ATTENTION
7-54
(Enter button) to confirm the setting.
(Exit button) at the end and the LCD display goes back to [Ready]
This screen is displayed only when both of fi-486PRFR and
fi-486PRRE are installed.
7.3 Setup Mode Details
25. Setting Imprinter numbering
1) Press
(Next button) or
(Previous button) and let LCD display
<Screen25>.
<Screen25>
!
=
HINT
2
5
N
O
u
n
m
/
b
O
e
f
r
f
i
(
n
x
g
x
x
x
)
To show your selection of imprinter or the imprinter to setup, [Pre] or [Post]
is displayed.
(Left
Press
(Enter button) to confirm the selection. Then <Screen25-1> is
displayed.
If numbering printing is not required, press
[Off]. Then press
(Right arrow button) and select
(Enter button) to confirm.
<Screen25-1>
!
=
2
5
-
1
D
5
i
/
g
i
8
t
s
The blinking item is the one selected.
HINT
7.3 Setup Mode Details 7-55
OPERATOR PANEL MENUS
2) At <Screen25>, to enable numbering printing with the imprinter, press
arrow button) and select [On].
7
3) At <Screen25-1>, press
(Left arrow button) or
let your choice of number of digits blink.
Selectable number of digits is listed as below.
(1) [5] is blinking:
5 digit
(2) [8] is blinking:
8 digit
Press
(Right arrow button) and
(Enter button), then <Screen25-2> is displayed.
<Screen25-2>
!
=
2
5
0
0
2
0
0
S
0
t
0
a
0
r
0
t
C
o
u
n
t
4) At <Screen25-2>, specify the initial value of numbering.
By pressing
(Left arrow button) or
(blinking on LCD) can be specified.
By pressing
(Next button) or
can be changed.
(Right arrow button), a digit position
(Previous button), the number at the digit
After putting a initial value for the numbering counter, press
(Enter
button) to confirm the initial number. Then, <Screen25-3> is displayed.
<Screen25-3>
!
=
HINT
7-56
2
5
-
3
O
E
n
m
/
p
O
t
f
y
f
R
e
Initial number can be increased up to the maximum number
(5digit: 99,999 / 8digit: 16,777,215).
7.3 Setup Mode Details
s
e
t
5) At <Screen25-3>, you can specify if the numbering should be initialized to the
specified initial value in 4) at hopper empty.
To specify to initialize the numbering counter at hopper empty, press
arrow button) and select [On].
(Left
Press
(Enter button) to confirm the selection. Then, <Screen25-4> is
displayed.
To specify not to initialize the counter at hopper empty but continue
incrementing, select [Off], press
is displayed.
(Enter button) and then <Screen 25-4>
!
=
2
5
-
4
R
e
s
N
e
o
t
/
Y
N
e
o
s
w
6) At <Screen25-4>, specify if the numbering counter should be initialized
immediately to the vlaue specified in 4).
To specify to initialize immediately, press
[Yes].
(Right arrow button) and select
To specify not to initialize immediately, select [No] and press
button).
7) Press
Press
ATTENTION
(Enter
(Enter button) to confirm the setting.
(Exit button), and the LCD display goes back to [Ready] screen.
Command from the PC takes the priority over the setting from the Operator
panel.
7.3 Setup Mode Details 7-57
OPERATOR PANEL MENUS
<Screen25-4>
7
26. Reset the Ink remain counter of imprinter.
If the following message comes up, prepare the new Print cartridge. If no further
printing is not possible, replace the Print cartridge and reset the ink counter. If
the Print cartridge is replaced before Print cartridge error occurs, be sure to reset
the Ink remain counter.
P
N
r
o
e
w
p
a
R
r
e
e
a
d
n
i
e
n
w
g
!
I
x
n
x
k
x
x
N
o
[XXXX] is the scanned sheet counter value.
HINT
1) Press
(Next button) or
<Screen26>.
(Previous button) and let LCD display
<Screen26>
!
=
2
6
J
J
J
I
n
k
J
F
F
(
x
R
x
e
Approximate remaining ink amount is shown as below:
-
Cartridge is full.
-
Cartridge is low or empty.
In [XXXX], [Pre] or [Post] is displayed.
HINT
7-58
7.3 Setup Mode Details
x
s
x
e
)
t
/
2) At <Screen26>, to choose to reset the ink counter, press
button) and select [Reset].
Press
(Left arrow
(Enter button). <Screen26-1> is displayed.
Not to reset, select [No] and press
(Enter button).
<Screen26-1>
!
2
6
-
1
R
e
s
N
e
o
t
/
To cancel the reset, select [No] and press
N
e
o
s
7
w
(Right arrow button)
(Enter button).
4) Press
(Enter button) and reset the counter.
The remaining ink amount indication on LCD goes back to full (
).
<Screen26>
!
=
5) Press
2
6
J
J
J
I
n
k
J
J
J
(
x
R
x
e
x
s
x
e
)
t
/
N
o
(Exit button), and the LCD display goes back to [Ready] screen.
7.3 Setup Mode Details 7-59
OPERATOR PANEL MENUS
3) At <Screen26-1>, to actually reset the counter, press
and select [yes].
Y
27. Setting Power save mode
1) Press
(Next button) or
<Screen27>.
(Previous button) and let LCD display
<Screen27>
!
=
2
7
P
o
w
e
r
2) At <Screen27>, press
(Left arrow button) or
select [On] to use power save mode.
Next, press
S
a
v
e
(Right arrow button)and
(Enter button). Then the LCD display shows <Screen27-1>.
If power save mode is not required, press
[Off].Then, press
(Right arrow button) and select
(Enter button).
<Screen27-1>
!
=
2
7
1
1
0
T
i
1
m
5
e
2
0
m
i
n
3) At <Screen27-1> ,by pressing
(Left arrow button) or
(Right arrow
button), select the scanner wait idle time before entering power save mode.
The blinking item is the one selected.
HINT
A minimum of 5 minutes to the maximum of 60 minutes can be selected with 5
minutes increment.
HINT
4) Press
press
7-60
The default time recommended by the ENERGY STAR® program is 15 minutes.
(Enter button) and enable to use power save mode. Finally,
(Exit button) and the LCD display goes back to [Ready] screen.
7.3 Setup Mode Details
28. Setting Brightness
1) Press
(Next button) or
<Screen28>.
(Previous button) and let LCD display
<Screen28>
!
2
C
8
h
a
B
n
r
g
i
e
g
?
h
Press
n
o
e
/
s
Y
s
e
7
s
(Right arrow button) and
(Enter button) to confirm the selection. <Screen28-1> is displayed.
If Brightness adjustment is not required, select [No] and press
button).
(Enter
<Screen28-1>
!
F
2
r
8
o
n
1
t
B
:
r
0
i
g
B
h
a
t
c
n
k
e
:
s
s
0
The blinking item is the one selected.
HINT
3) At <Screen28-1>, to adjust the front-side brightness, press
button) and select [Front].
If back side needs brightness adjustment, press
select [Back].
(Left arrow
(Right arrow button) and
To increase the brightness, press
(Next button). Each time the button is
pressed the brightness value increases by 1.
To decrease the brightness, press
(Previous button). Each time the button
is pressed, the brightness decreased by 1.
4) Press
Press
(Enter button) to confirm the setting.
(Exit button), and the LCD display goes back to [Ready] screen.
7.3 Setup Mode Details 7-61
OPERATOR PANEL MENUS
2) At <Screen28>, to adjust the Brightness, press
select [Yes].
t
N
29. Confirming Imprinter installation
1) Press
(Next button) or
<Screen29>.
(Previous button) and let LCD display
<Screen29>
!
S
2
t
9
a
t
I
u
m
s
p
r
i
P
n
o
t
s
e
t
r
/
P
[XXXX/XXXX], imprinter installation status is displayed as follows.
(1) Only fi-486PRFR is installed:
[Pre]
(2) Only fi-486PRRE is installed:
[Post]
(3) Both fi-486PRFR and fi-486PRRE are
installed:
[Post/Pre]
2) By pressing
7-62
(Exit button), LCD display goes back to “Ready”.
7.3 Setup Mode Details
r
e
30. Setting Lamp Control
1) Press
(Next button) or
<Screen30>.
(Previous button) and let LCD display
<Screen29>
!
S
2) At <Screen30>, press
2
t
9
a
t
I
u
m
s
p
r
i
P
n
o
t
s
e
t
r
/
P
r
e
(Left arrow button) to select [Normal] or press
(1) [Normal] is blinking:
[Normal] mode is
selected.
(2) [AlwaysOn] is blinking:
[AlwaysOn] mode is
selected. The lamp is kept
turned on.
(Exit button), LCD display goes back to “Ready”.
7.3 Setup Mode Details 7-63
OPERATOR PANEL MENUS
(Right arrow button) to select [AlwaysOn].
3) By pressing
7
7.4
Test Mode Overview
■ Outline
Scanner operation can be checked in the offline test mode.
To enter the test mode, follow the procedures below.
- Test mode
Keep pressing
(Start button) and turn on the power.
Then the Operator panel LCD displays the following message.
<
Press
(Left arrow button) or
By pressing
M
S
O
E
D
T
E
U
S
P
L
T
E
E
(Enter button), the scanner enters test mode.
The blinking item is the one selected.
HINT
7.4 Test Mode Overview
C
S
T
T
>
(Right arrow button) and select [TEST].
To end the test mode, turn off the power.
7-64
E
■ Button functions in test mode
Button name
[Next]
[Previous]
Function
Displays the next menu item without saving the change.
Referred to as Next button in this manual.
Displays the previous menu item without saving the change.
Referred to as Previous button in this manual.
Moves to the left item on the menu.
Referred to as Left arrow button in this manual.
Saves the change and then displays the next menu item
Referred to as Enter button in this manual.
Moves to the upper level menu item without saving the change.
Referred to as Exit button in this manual.
■ Transition of screens in test mode
Refer to the next page.
The LCD screen transition chart in the following pages show the concept.
The flow charts in the following pages show the transition of the LCD screen.
For the details, please refer to the descriptions in “ Contents of test mode setting” on
page 7-69.
7.4 Test Mode Overview 7-65
OPERATOR PANEL MENUS
Moves to the right item on the menu.
Referred to as Right arrow button in this manual.
7
T
i
1
S
A
T
4
A
P
R
T
A
4
e
P
t
S
S
S
0
n
g
l
B
W
S
B
e
e
f
u
t
e
e
d
2
0
0
2
0
0
R
P
S
7-66
I
M
P
L
S
E
I
X
M
A
P
P
e
/
L
a
e
E
A
tD
E
d
C
S
P
P
7.4 Test Mode Overview
E
L
Ie
E
O
S
n
L
i
O
R
4
U
X
(Scanning)
Start scanning, or setup
imprinter test conditions
p
W
R
Continue to screen T02 on the next page
g
O
Z
t
X
L
2
M
R
E
U
0
o
e
T
0
d
t
I
e
e
O
t
N
T
u
2
S
A
T
4
A
P
R
T
A
4
e
P
t
S
S
M
0
l
t
i
B
W
S e
B
e
f
u
t
e
d
2
0
0
2
0
0
P
S
I
M
P
L
S
E
I
X
M
A
P
P
/e
L
a
E
A
t
D
E
d
C
S
P
P
L
I
e
E
O
S
n
L
i
O
R
4
U
X
E
g
O
tZ
7
L
2
M
U
0
o
e
T
0
d
t
I
e
O
OPERATOR PANEL MENUS
R
e
(Scanning)
Start scanning, or setup
imprinter test conditions
p
W
R
Continue to screen T03 on the next page
tN
e
R
E
X
7.4 Test Mode Overview 7-67
7-68
T
0
3
L
A
M
D
P
e
v
i
c
e
O
F
B
:f
:
xf
x
sx
x
x
e
x
xt
x
L
i
f
e
T
0
4
x
x
x
x
x
x
x
x
P
o
P
s
r
7.4 Test Mode Overview
O
t
e
p
t
i
o
n
s
O
p
p
fr
r
fi
i
sn
n
e
t
t
e
t
e
r
r
:
:
g
■ Contents of test mode setting
LCD display
Descriptions
Single feed
Scans a sheet of document without connecting to a PC.
Multi feed
Scans documents continuously without connecting to a PC.
Device Life
Shows the cumulative lamp-on time.
Options
Shows the options installation status.
7
OPERATOR PANEL MENUS
7.4 Test Mode Overview 7-69
7.5 Test Mode Details
1.
Single feed
Without connecting to a PC, the scanner's whole mechanism’s operation can be
checked.
Only one sheet is fed with this test.
Scan parameters can be changed for scan test.
Imprinter test print can be performed at the same time.
1) Place the documents to scan on the hopper.
2) Press
(Next button) or
<Screen50>.
(Previous button) and let the LCD show
<Screen50>
T
0
S
1
i
n
g
l
3) At <Screen50>, press
(Enter button) or
<Screen50-1> is displayed.
e
f
e
e
d
(Start button). Then
<Screen50-1>
S
S
A
T
4) At <Screen 50-1>, press
4
A
P
R
B
T
W
S e
2
t
u
0
0
p
(Right arrow button) and select [Setup].
Press
(Enter button) or
displayed.
(Start button). Then <Screen50-2> is
<Screen50-2>
S
A
4
P
e
B
t
2
W
0
0
5) Specify the scanning conditions.
(1)At <Screen50-2>, select the left most item, [S] in the sample screen, and
press
2.1>.
(Enter button). Then the LCD display shows <Screen50<Screen50-2.1>
S
7-70
7.5 Test Mode Details
I
M
P
L
S
E
I
X
M
P
/
L
E
D
X
U
P
L
E
X
At this screen, press
(Left arrow button) or
and select simplex or duplex.
(Right arrow button)
Press
(Enter button) and confirm the setting.
Then the display goes back to <Screen50-2>.
(2) At <Screen50-2>, select the second item from left, [A4P] in the sample
screen, and press
(Enter button). Then the LCD display shows
<Screen50-2.2>.
<Screen50-2.2>
P
A
P
R
4
S
P
I
Z
E
At this screen, press
(Left arrow button) or
(Right arrow button)
and select the document size and the orientation. Following parameters
can be specified.
A4 portrait
A4P
B4 portrait
B4P
Legal portrait
LGP
11 x 17 in. portrait
DLP
A3 portrait
A3P
A5 landscape
A5L
B5 landscape
B5L
Letter landscape
LTL
A4 landscape
A4L
A5 portrait
A5P
B5 portrait
B5P
Letter portrait
LTP
Press
(Enter button) and confirm the setting.Then the display goes
back to <Screen50-2>.
7.5 Test Mode Details 7-71
OPERATOR PANEL MENUS
E
A
7
(3)At <Screen50-2>, select the third item from left, [BW] in the sample
screen, and press
(Enter button). Then the LCD display shows
<Screen50-2.3>.
<Screen50-2.3>
R
e
a
d
C
i
O
n
L
g
O
M
o
d
e
R
In this screen, press
(Left arrow button) or
(Right arrow button)
and select the scan mode: binary (BW) or color (COLOR).
Press
(Enter button) and confirm the setting.Then the display goes
back to <Screen50-2>.
(4)At <Screen50-2>, select the right most item, [200] in the sample screen,
and press
2.4>.
(Enter button). Then the LCD display shows <Screen50<Screen50-2.4>
R
E
S
O
L
2
U
0
T
0
I
O
N
At this screen, press
(Left arrow button) or
(Right arrow button)
and select scan resolution. Following parameters can be specified.
200:
Scan at 200 dpi
240:
Scan at 240 dpi
300:
Scan at 300 dpi
400:
Scan at 400 dpi
Press
(Enter button) and confirm the setting.Then the display goes
back to <Screen50-2>.
(5)Press
(Enter button). Then the display goes back to <Screen50-1>.
At <Screen50-1>, select [START], and press
(Start button).
If fi-486PRFR and/or fi-486PRREis installed, <Screen50-3> is displayed
for setting imprinter test conditions.
If an imprinter(s) is not installed, the scanner starts scanning operations.
7-72
7.5 Test Mode Details
<Screen50-3>
=
O
f
f
P
/
r
O
i
n
n
:
t
P
r
/
P
o
s
t
(Right arrow button)
If imprinter test is not required, select [Off].
7) Press
(Start button). Scanning operation starts with or without
imprinter test.
HINT
To quit the test, press
(Stop button).
LCD display goes back to <Screen50>.
7.5 Test Mode Details 7-73
7
OPERATOR PANEL MENUS
6) At <Screen50-3>, press
(Left arrow button) or
and:
Select [On] to do imprinter test while scanning.
Then select the imprinter to use.
If the printer to use is fi-486PRFR, select [Pre].
If fi-486PRRE, select [Post].
e
2. Multi feed
Without connecting to a PC, the scanner's whole mechanism’s operation can be checked.
In this test documents are scanned continuously.
Scan parameters can be changed for scanning test.
Imprinter test print can be performed at the same time.
1) Place the documents to scan on the hopper.
2) Press
(Next button) or
(Previous button) and let the LCD show
<Screen51>.
<Screen51>
T
0
M
2
u
l
t
i
3) At <Screen51>, press
(Enter button) or
<Screen51-1> is displayed.
f
e
e
d
(Start button), then
<Screen51-1>
S
S
4) At <Screen 50-1>, press
A
T
4
A
P
R
B
T
W
S e
2
t
u
0
0
p
(Right arrow button) and select [Setup].
Press
(Enter button) or
(Start button). Then <Screen51-2> is
displayed.
<Screen51-2>
S
7-74
7.5 Test Mode Details
A
4
e
P
t
B
W
2
0
0
5) Specify the scanning conditions.
(1)At <Screen51-2>, select the left most item, [S] in the sample screen, and
press
2.1>.
(Enter button). Then the LCD display shows <Screen51<Screen51-2.1>
S
I
M
P
L
S
E
I
X
M
P
/
L
D
X
E
P
L
E
X
(Right arrow button)
Press
(Enter button) and confirm the setting.
Then the display goes back to <Screen51-2>.
(2) At <Screen51-2>, select the second item from left, [A4P] in the sample
screen, and press
(Enter button). Then the LCD display shows
<Screen51-2.2>.
<Screen51-2.2>
P
A
P
E
A
R
4
S
P
I
Z
E
At this screen, press
(Left arrow button) or
(Right arrow button)
and select the document size and the orientation. Following parameters
can be specified.
7.5 Test Mode Details 7-75
7
OPERATOR PANEL MENUS
At this screen, press
(Left arrow button) or
and select simplex or duplex.
U
A4 portrait
A4P
B4 portrait
B4P
Legal portrait
LGP
11 x 17 inch portrait
DLP
A3 portrait
A3P
A5 landscape
A5L
B5 landscape
B5L
Letter landscape
LTL
A4 landscape
A4L
A5 portrait
A5P
B5 portrait
B5P
Letter portrait
LTP
Press
(Enter button) and confirm the setting.Then <Screen51-2> is
redisplayed.
(3)At <Screen51-2>, select the third item from left, [BW] in the sample
screen, and press
(Enter button). Then the LCD display shows
<Screen51-2.3>.
<Screen51-2.3>
R
e
a
d
C
i
O
n
L
g
O
M
o
d
e
R
In this screen, press
(Left arrow button) or
(Right arrow button)
and select the scan mode: binary (BW) or color (COLOR).
Press
(Enter button) and confirm the setting. Then the display goes
back to <Screen51-2>.
(4)At <Screen51-2>, select the right most item, [200] in the sample screen,
and press
2.4>.
(Enter button). Then the LCD display shows <Screen51<Screen51-2.4>
R
7-76
7.5 Test Mode Details
E
S
O
L
2
U
0
T
0
I
O
N
At this screen, press
(Left arrow button) or
(Right arrow button)
and select scan resolution. Following parameters can be specified.
200:
Scan at 200 dpi
240:
Scan at 240 dpi
300:
Scan at 300 dpi
400:
Scan at 400 dpi
7
(5) Press
(Enter button). Then <Screen51-1> is redisplayed.
At <Screen51-1>, select [START] and press
(Start button).
If fi-486PRFR and/or fi-486PRREis installed, <Screen51-3> is displayed
for setting imprinter test conditions.
If an imprinter(s) is not installed, the scanner starts scanning operations.
<Screen51-3>
=
6)
O
f
f
P
/
r
O
i
n
n
:
t
P
At this screen, press
(Left arrow button) or
Select [On] to do imprinter test while scanning.
Then, select the imprinter to use.
If the printer to use is fi-486PRFR, select [Pre].
If fi-486PRRE, select [Post].
r
e
/
P
o
s
t
(Right arrow button) and:
If imprinter test is not required, select [Off].
7.5 Test Mode Details 7-77
OPERATOR PANEL MENUS
Press
(Enter button) and confirm the setting. Then <Screen51-2> is
redisplayed.
7) Press
(Start button). Scanning operation starts with or without
imprinter test.
HINT
7-78
To quit the test, press
(Stop button).
The LCD goes back to <Screen51>.
7.5 Test Mode Details
3. Display the cumulative lamp-on time
You can check the cumulative number of lamp-on time.
1) Press
(Next button) or
(Previous button) and let LCD display
<Screen53>.
<Screen53>
T
0
D
3
e
v
i
c
L
i
f
e
(Enter button). Then
<Screen53-1>
L
A
M
P
O
F
B
f:
:
xf
x
sx
x
e
x
x
xt
x
x
x
x
x
x
x
x
x
[F: XXXXXXXX] indicates the cumulative lamp-on time for the Front-side
lamp.
[B: XXXXXXXX] indicates the cumulative lamp-on time for the Back-side
lamp.
The unit of lamp-on time is minute.
3) Press
(Stop button) or
redisplayed.
(Exit button). Then <Screen53> is
7.5 Test Mode Details 7-79
7
OPERATOR PANEL MENUS
2) At <Screen53>, press
(Start button) or
<Screen53-1> is displayed.
e
4. Option installation status display
You can check the options installation status.
1) Press
(Next button) or
(PreviousPrevious button) and let LCD
display <Screen54>.
<Screen54>
T
0
O
4
p
t
i
o
2) At <Screen54>, press
(Enter button) or
<Screen54-1> is displayed.
<Screen54-1>
P
o
P
s
r
t
e
O
p
p
fr
r
if
i
n
s
(Start button).
s
n
n
e
t
t
e
t
e
r
r
:
:
J
If fi-486PRFR is installed, LCD display shows [Pre Printer: ]. [ ]
indicates that the printer is installed. If not installed, it shows [Pre Printer:-].
If fi-486PRRE is installed, LCD display shows [Post Printer: ]. [ ]
indicates that the printer is installed. If not installed, it shows [Post Printer:].
3) Press
(Exit button) or
redisplayed.
7-80
7.5 Test Mode Details
(Stop button). Then <Screen54> is
8
OPTIONS
This chapter describes options for fi-4860C.
8.1 Options ................................................................................8-2
8.2 fi-486PRFR (Front side imprinter) .....................................8-3
8.3 fi-486PRRE (Rear side imprinter) ......................................8-4
8.4 fi-486TRK (Thinner paper Roller Kit) ................................8-5
8-1
8.1 Options
The following lists options available for the scanner.
Name
Part No.
Description
fi-486PRFR
PA03296-D207
Prints information on the front of a document prior to scan.
Installed before the scanner optics. Imprinted data is
captured during scan.
fi-486PRRE
PA03296-D200
Prints information on the back of a document after scan.
Installed after the scanner optics. Imprinted data is not
captured during scan.
fi-486TRK
PA03296-D780
For the details please contact FUJITSU scanner dealer where you purchased the scanner or
FUJITSU group company responsible for your country.
ATTENTION
8-2
8.1 Options
The both imprinters can be installed on the scaner at the same time.
However, only one of them can print at a time.
Depending on the application, appropriate imprinter should be specified.
8.2 fi-486PRFR (Front side imprinter)
fi-486PRFR is installed at the front side of the document path, inside of the scanner. It prints prior
to scanning. fi-486PRFR (Front side imprinter) Specifications are described below.
Item
Descriptions
Thermal Ink Jet
Printable characters
Alphabet letters : A to Z, a to z
Numeric characters: 0,1 to 9
Symbols : ! ” # $ % & ¥ ( ) * + , - . / : ; < = > ? @ [ \ ] ^ _
Maximum printable
characters per line
40
Character size
Height 2.91 mm (0.11 inch) x Width 2.82 mm (0.11 inch)
Character pitch
Approximately 3.53 mm (8 characters/inch)
Printing area
Printable area is shown as below.
{|}
Ducument Reference Position
D
Printing
Area (Front)
C
B
Consumables
Center of document
E
Document feeding direction
A: 40 mm (1.7 inch) or more
B: 99 mm (3.9 inch) or less
C: 5 mm (0.2 inch) or more
D: 140.5 mm (5.5 inch) or less
(Max. 40 column)
E: 5 mm (0.2 inch) or more
8
OPTIONS
Printing Method
A
Print Cartridge
As for the operations and functions of fi-486PRFR (Front side imprinter), refer to the fi-486PRFR
Operator's Guide attached to fi-486PRFR.
8.2 fi-486PRFR (Front side imprinter)
8-3
8.3 fi-486PRRE (Rear side imprinter)
fi-486PRRE is installed at the rear side of the document path, inside of the scanner. It prints after
the scanning. fi-486PRFR (Rear side imprinter) Specifications are described below.
Item
Descriptions
Printing Method
Thermal Ink Jet
Printable characters
Alphabet letters : A to Z, a to z
Numeric characters: 0,1 to 9
Symbols : ! ” # $ % & ’ ( ) * + , - . / : ; < = > ? @ [ ¥ ] ^ _
Maximum printable
characters per line
40
Character size
Height 2.91 mm (0.11 inch) x Width 2.82 mm (0.11 inch)
Character pitch
Approximately 3.53 mm (8 characters/inch)
Printing area
Printable area is shown as below.
{|}
E
Document feeding direction
A: 43 mm (1.7 inch) or more
B: 100.5 mm (3.9 inch) or less
C: 5 mm (0.2 inch) or more
D: 140.5 mm (5.5 inch) or less
(Max. 40 column)
E : 5 mm (0.2 inch) or more
Center of document
Ducument Reference Position
A
Consumables
Printing
Area (Back)
D
C
B
Print Cartridge
As for the operations and functions of fi-486PRRE (Rear side imprinter), refer to the fi-486PRRE
Operator's Guide attached to fi-486PRRE.
8-4
8.3 fi-486PRRE (Rear side imprinter)
8.4 fi-486TRK (Thinner paper Roller Kit)
fi-486TRK provides smooth paper feeding when reading documents smaller than Letter/A4 size
and thinner than the standard thickness (31 g/m2 to 52 g/m2 or 12.4 lbs to 14 lbs). It is also
effective for scanning documents with paper dust. Refer to the section "6.2 Document Quality
(on page 6-3)" for the document thickness.
For details on attaching fi-486TRK, refer to the sections "4.3 Replacing the Pad ASSY (on page
4-4)", "4.4 Replacing the Pick Roller Unit (on page 4-9)" and "4.5 Replacing the Brake Roller
Unit (on page 4-12)".
fi-486TRK contains the following parts.
Standard replacement cycle
Pick Roller Unit
(Rubber foam)
300,000 sheets or 1 year
Brake Roller(Rubber
foam)
300,000 sheets or 1 year
Pad ASSY
300,000 sheets or 1 year
HINT
OPTIONS
Descriptions
When using fi-486TRK, documents of coated paper (e.g. photos, magazines, etc.) may not be fed into the ADF successfully. For scanning such
documents, the standard pick roller unit and the brake roler unit are recommended.
8.4 fi-486TRK (Thinner paper Roller Kit)
8
8-5
8-6
8.4 fi-486TRK (Thinner paper Roller Kit)
9
SCANNER
SPECIFICATIONS
This chapter describes the Scanner Specifications.
9.1 Basic Product Specifications ............................................9-2
9.2 Installation Specifications .................................................9-3
9.3 Dimensions .........................................................................9-5
9-1
9.1 Basic Product Specifications
1
Scanner Type
ADF(Automatic Document Feeder)
and Manual feed
-
2
Image sensor
Color CCD x 2
Front/Back
3
Light source
White fluorescent lamp x 2
Front/Back
4
Scanning area
Minimum
74 mm x 74 mm, 2.9 in. x 2.9 in.
-
Maximum
A3 or 11x17 in.
-
52 g/m2 to 127 g/m2 or 14 lb to 34 lb
(* 1)
5
Document thickness
6
Scanning speed
(A4 Portrait/Letter
Portrait)
(* 2)
Binary (Black and Simplex 60 ppm
White)
Duplex 120 ipm
200dpi
Grayscale
Simplex 60 ppm
Duplex 120 ipm
200dpi
Color
Simplex 60 ppm
Duplex 120 ipm
150 dpi (* 3)
200 dpi (* 3)
7
ADF capacity (* 4)
500 sheets
A4 80 g/m2, or
Letter 20 lb
8
Optical resolution
400 dpi
-
9
Output resolution
Binary (Black and 100, 150, 200, 240, 300, 400 dpi
White)
-
Grayscale
100, 150, 200, 240, 300, 400 dpi
-
Color
100, 150, 200, 300, 400 dpi
(* 5)-
10
Grayscale level
8 bits
10 bits
internal
11
Output mode of halftone patterns
Dither/Error diffusion
-
12
Interface (* 6)
Ultra Wide SCSI
Shielded, 68
pin half density
(High Density
DB68)
13
Other functions
JPEG compression
-
(* 1) For details, refer to “Chapter 6 ADF DOCUMENT SPECIFICATIONS” on page 6-1.
(* 2) The scanning speed is the maximum speed of the scanner hardware. The actual speed may be
slower due to the system overhead such as data transfer time.
(* 3 )With JPEG enabled
(* 4) The maximum capacity varies depending on the document thickness. Refer to “Chapter 6 ADF
DOCUMENT SPECIFICATIONS” on page 6-1.
(* 5) A3 and 11 x17in document sizes are not supported at color 400dpi.
(* 6) Avoid connecting other SCSI devices to the same bus.
It can reduces the scaner throughput.
9-2
9.1 Basic Product Specifications
9.2 Installation Specifications
Item
Dimensions
(With hopper and stacker retracted)
Specification
Depth
Width
Height
431 mm,
17 in.
520 mm,
20.5 in.
523 mm,
20.6 in.
Space requirements
9
100 mm
4 in.
SCANNER SPECIFICATIONS
Scanner
500 mm
19.7 in.
100 mm
4 in.
600 mm
23.6 in.
Front
Weight (kg)
Input power
Power consumption
45 kg, 99 lb
Voltage
AC100 - 240 V±10 %
Phase
Single-phase
Frequency
50/60 Hz +2/-4 %
200 W or less
9.2 Installation Specifications
9-3
Item
Ambient condition Device status
9-4
Specification
Operating
Not operating
Temperature
15 -- 35 degrees Celsius
59 -- 95 degrees Fahrenheit
-20 -- +60 degrees Celsius
-4 -- +140 degrees Fahrenheit
Humidity
20 - 80 %
8 - 95 %
Heat capacity
172 kcal or less
Shipping Weight (kg)
50 kg, 110 lb
9.2 Installation Specifications
(17in)
9.3 Dimensions
(20.6 in.)
(20.6 in.)
523
(20.5 in.)
520
(20.5 in.)
unit: mm
9-5
9.3 Dimensions
9-6
9.3 Dimensions
APPENDIX1 DROP-OUT COLOR
A drop-out color is a color that can be eliminated from what the scanner sees.
To check the background color of document for drop-out, use the method and follow the standards
given below.
Print density measurement
The measurement must be made in one of the following ways:
- A fluorescent light source.
- Macbeth PCS meter PCM II is used, which requires a filter.
100
Relative Spectral Power
90
80
70
60
50
40
30
20
10
0
400
500
600
700
Wave Length (nm)
Drop-out color standard
In the spectrum of the fluorescent lamp the PCS value must satisfy the
following standards:
- Maximum Density: 0.14 or less
- Average Density: 0.1 or less
●AP-1
APPENDIX2 DOUBLE-FEED DETECTION
CONDITIONS
There are three double-feed detection modes: document thickness, document length, and both
document thickness and length. The following conditions must be satisfied in each of these
detection modes. (When fi-486TRK is not installed.)
Detection by Document Overlapping
- Paper weight: 52 g/m2 - 127 g/m2 or 14 lbs to 34 lbs
- Punched holes are not allowed within 35mm (1.4 inch) of the vertical center line
of the document.
Detection by Document Thickness
Sheets of the same thickness shall be set in the ADF at a time.
- Paper weight: 52 g/m2 - 127 g/m2 or 14 lbs to 34 lbs
- Printed area: 12% or less
- No black printed areas are allowed at the center area (26 x 10mm or 1 x 0.4
inch) at the leading edge of the document.
- Punched holes are not allowed within 35mm (1.4 inch) of the vertical center line
of the document.
- The deviation in the amount of the light transmitted through background areas
must not be less than 10%.
Detection by Document Length
Sheets of the same length shall be set in the ADF at a time.
- Document length deviation: 1% or less
- Printed area: 12% or less
- No black printed areas are allowed at the center area (26 x 10mm or 1 x 0.4
inch) at the leading edge of the document.
- Punched holes are not allowed within 35mm (1.4 inch) of the vertical enter line
of the document.
- The deviation in the amount of the light transmitted through background areas
must not be less than 10%.
Detection by Document Overlapping and Thickness
Sheets of the same thickness shall be set in the ADF at a time.
- Paper weight: 52 g/m2 - 127 g/m2 or 14 lbs to 34 lbs
- Printed area: 12% or less
- No black printed areas are allowed at the center area (26 x 10mm or 1 x 0.4
inch) at the leading edge of the document.
●AP-2
- Punched holes are not allowed within 35mm (1.4 inch) of the vertical center line
of the document.
- The deviation in the amount of the light transmitted through background areas
must not be less than 10%.
Detection by Document Overlapping and Length
Sheets of the same thickness and length shall be set in the ADF at a time.
- Paper weight: 52 g/m2 - 127 g/m2 or 14 lbs to 34 lbs
- Document length deviation: 1% or less
- Printed area: 12% or less
- No black printed areas are allowed at the center area (26 x 10mm or 1 x 0.4
inch) at the leading edge of the document.
- Punched holes are not allowed within 35mm (1.4 inch) of the vertical center line
of the document.
- The deviation in the amount of the light transmitted through background areas
must not be less than 10%.
Detection by Document Thickness and Length
Sheets of the same thickness and length shall be set in the ADF at a time.
- Paper weight: 52 g/m2 - 127 g/m2 or 14 lbs to 34 lbs
- Document length deviation: 1% or less
- Printed area: 12% or less
- No black printed areas are allowed at the center area (26 x 10mm or 1 x 0.4
inch) at the leading edge of the document.
- Punched holes are not allowed within 35mm (1.4 inch) of the vertical center line
of the document.
- The deviation in the amount of the light transmitted through background areas
must not be less than 10%.
Detection by Document Overlapping, Thickness and Length
Sheets of the same thickness and length shall be set in the ADF at a time.
- Paper weight: 52 g/m2 - 127 g/m2 or 14 lbs to 34 lbs
- Document length deviation: 1% or less
- Printed area: 12% or less
- No black printed areas are allowed at the center area (26 x 10mm or 1 x 0.4
inch) at the leading edge of the document.
- Punched holes are not allowed within 35mm (1.4 inch) of the vertical center line
of the document.
●AP-3
- The deviation in the amount of the light transmitted through background areas
must not be less than 10%.
HINT
HINT
●AP-4
The type and the conditions of document and the conditions sometimes
cause the double-feed detection rate to drop.
When the overlapping check is specified, the paper sheets which contact
closely each other, such as electro-statically charged paper, can result in the
miss-detection of double feed.
APPENDIX3 MESSAGES OF OPERATOR
PANEL
■ Massages of Scaner Operation Status
<Not Ready status>
(Initializing)
changes to with progress of time, and when all become , it
move to the following check states.
J
J
J
F
F
F
F
<Not Ready status>
(Ejecting document)
E j
W a
e
r
c
m
t
i
i
n
n
g
g
-
p
p
a
u
<Not Ready status>
(Checking sensor)
C h
W a
e
r
c
m
k
i
i
n
n
g
g
-
s
p
e
u
R e
W a
s
r
e
m
t
i
t
n
i
g
n
-
g
u
W a
i
t
i
n
g
P
a
l
e
n
a
e
s
w
e
P
a
l
e
n
a
e
s
w
e
P
a
l
e
n
a
e
s
w
e
<Not Ready status>
(Resetting the hopper)
<Not Ready status>
(Waiting to initialize
interface board)
Low ink alarms
<preparing the print
cartridge>
(At power on )
p
N
e
o
r
w
!
!
n
N
s
o
o
w
r
!
!
p
o
N
p
o
p
w
e
!
r
!
I
F
R
e
a
d
y
p
(
a
p
r
r
e
e
)
p
(
a
p
r
o
e
s
t
)
p
(
a
B
r
o
e
t
h
)
h
p
n
r
k
e
I
p
n
r
k
e
I
p
n
r
k
e
I
●AP-5
<Scanning>
P
N
r
o
e
w
p
a
R
r
e
e
a
d
n
i
e
n
w
g
!
I
x
n
x
k
x
x
d
i
n
g
!
x
x
x
x
"xxxx" shows the Batch counter value.
HINT
<Scanning>
N
o
w
R
e
a
"xxxx" shows the Batch counter value.
HINT
<At Low power
mode>
ATTENTION
●AP-6
When the messages of LCD on the Operation panel disappears
and the Power LED lamp lights, the scanner is in the Low power
mode.
The scanner wakes up from Low power mode by one of the following operations.
Press any button (except Power button) on the Operator Panel.
Set the documents on the Hopper.
Send the command from PC.
<Double feed error> The following message is displayed while the scanner is scanning continuously in the state where double feed has been
(Scanning)
detected (by overlapping check).
If a double feed detection state is canceled on “Ready“ screen
after scanning, the upper row of this message disappears.
S
N
U
o
D
R
S
w
o
e
u
a
b
d
l
i
e
n
g
F
!
e
x
e
x
d
x
x
"xxxx" shows the number of Batch counter value.
HINT
(Waiting)
The following message is displayed while the scanner is waiting
in the state when double feed has been detected (check in overlapping).
Press the [Stop] button, and the double feed detection state is
canceled.
The upper row of this message, [Double Feedxxxxx] blinks.
S
HINT
U
S
R
e
D
a
.
d
f
y
e
e
x
d
x
x
x
x
x
x
x
x
x
x
x
x
"xxxx"(upper) shows the value of Batch counter.
"xxxxxxxx"(lower) shows the value of Abrasion counter or the value of Life
counter.
<Double feed error> The following message is displayed while the scanner is scanning continuously in the state where double feed has been
(Scanning)
detected (by thickness check).
If a double feed detection state is canceled on “Ready“ screen
after scanning, the upper row of this message disappears.
N
o
D
w
o
u
R
b
e
l
a
e
d
i
F
n
e
g
e
!
d
x
x
x
x
●AP-7
"xxxx" shows the number of Batch counter value.
HINT
(Waiting)
The following message is displayed while the scanner is waiting
in the state when double feed (check thickness) has been
detected.
Press the [Stop] button, and the double feed detection state is
canceled.
The upper row of this message, [Double Feedxxxxx] blinks.
D
HINT
●AP-8
o
u
R
b
e
l
a
e
d
F
y
e
x
e
x
d
x
x
x
x
x
x
x
x
x
x
x
"xxxx"(upper) shows the value of Batch counter.
"xxxxxxxx"(lower) shows the value of Abrasion counter or the value of Life
counter.
■ Error mesage (Temporary error :Check LED blinking)
Check LED blinks when the following errors occur except <Hopper empty> and <Mis-pick>.
<Hopper empty>
The following messages are displayed if no documents are on
the hopper during the scanning opperation. Please place documents on the hopper. Scanning is continued, when you place
documents on the hopper for re-scanning.
To clear this message, press the
P
a
p
e
button.
r
E
m
p
x
t
x
y
x
x
x
x
t
x
y
x
x
x
Check LED does not blink at Hopper empty error.
HINT
(at Double feed)
D
o
u
P
b
a
l
p
e
e
F
r
e
E
e
m
d
p
"xxxx" shows the number of Batch counter value.
HINT
<Paper Jam>
The following message displayed if a document is jammed in the
ADF.
Refer to "5.1 Clearing Document Jams" on page 5-2 for removing the document remained in the scanner.
P
a
p
e
r
J
a
m
x
One of "1" - "8" is displayed instead of "x", depending on paper jam status.
HINT
●AP-9
<ADF cover open>
The following message is displayed if the ADF cover is not
closed completely.
Close the ADF cover completely, to enable scanning.
A
D
F
-
C
o
v
e
r
O
p
e
n
<Double feed error> The following message is displayed, when the double feed is
(by thickness check) detected by thickness check.
D
(by length check)
u
b
l
e
F
e
e
d
The following message is displayed, when the double feed is
detected by length check.
L
<Mis-pick>
o
e
n
g
t
h
e
r
r
o
r
The following message is displayed, when a document is not
sent from the hopper to the ADF.
M
i
s
-
p
i
c
k
Check LED does not blink at Mis-pick error.
HINT
<Pick overrun>
The following message is displayed, when a document is sent
from the hopper to the ADF and it goes into too far than the normal position.
P
●AP-10
i
c
k
o
v
e
r
r
u
n
<Skew error>
The following message is displayed, When skewed document is
fed from the hopper to the ADF.
I
<Hopper is full or
Pick unit not set>
r
e
g
o
p
p
e
i
c
k
n
a
r
p
a
p
e
r
r
o
v
e
r
l
o
a
d
r
o
o
t
l
l
s
e
e
r
t
u
n
i
t
The following message is displayed, when the Pick roller unit is
not set correctly during scanning.
P
<Brake roller not
set>
l
The following message is displayed, when the Pick roller unit is
not set correctly.
(When the documents are not exist on the hopper.)
P
<Pick unit not set>
u
The following message is displayed, when the Pick roller unit is
not set correctly or when there are too many documents.
(When the documents are on the hopper.)
H
<Pick unit not set>
r
i
c
r
k
o
l
l
e
r
u
n
i
t
The following message is displayed, when scanning while the
Brake roller unit is not set correctly.
B
r
a
n
k
o
e
t
r
s
o
e
l
t
l
e
r
●AP-11
<Separation roller >
The following message is displayed, when the Separation roller
rotates while the Brake roller does not rotate at all.
r
S
o
e
l
p
l
a
e
r
r
a
t
w
i
o
o
r
n
n
<Checking Consum- The following message is displayed, when the Abrasion counter
ables>
value exceeds the setting value to display an consumables
replacement message.
A
<Print cartridge not
set>
●AP-12
b
r
a
s
i
o
n
a
l
a
r
m
The following message is displayed, when the Print cartridge is
not set to fi-486PRFR (Imprinter of front-side) or to fi-486PRRE
(Imprinter of rear-side).
P
o
r
N
P
o
o
N
e
I
n
k
C
a
r
t
r
i
d
g
e
s
I
t
n
k
C
a
r
t
r
i
d
g
e
■ Alarm message (Hardware error :Check LED lighting)
The following messages are displayed, when an error occurs inside the sccaner. In this case,
please switch on the power supply once again after disconnecting the power supply.
If the same message is displayed again, please contact a distributor or an nearest imaging service
and support center for help.
<Optical alarm >
(Front side)
The following message is displayed, when an error occurs to the
front side optical unit.
F
O
<Optical alarm >
(Back side)
o
t
n
i
t
c
a
S
l
i
d
A
e
l
a
r
m
The following message is displayed, when an error occurs to the
back side optical unit.
B
O
<Motor fuse alarm>
(Toransport motor)
r
p
a
p
c
t
k
i
c
S
a
i
l
d
e
A
l
a
r
m
The following messages are displayed, when the fuse of various
motors (Toransport motor, Separation motor, Pick motor, Hopper
motor) goes out.
F
F
u
e
s
e
e
d
p
F
a
u
r
s
a
e
t
F
P
u
i
s
c
e
k
F
o
u
p
s
p
e
e
(Separation motor)
S
e
(Pick motor)
(Hopper motor)
H
a
m
l
o
a
t
r
o
m
r
a
o
l
n
a
i
r
m
m
o
a
m
l
o
a
t
r
o
m
r
a
l
m
a
o
r
t
m
o
r
t
o
r
r
●AP-13
<Lamp fuse alarm>
(Front side)
The following message is displayed, when the fuse for the lamp
for front side blows out.
F
<Lamp fuse alarm>
(Back side)
r
i
a
d
l
e
a
r
l
m
a
m
p
a
F
c
u
k
s
e
s
i
a
d
l
e
a
r
l
m
a
m
p
a
c
F
k
u
g
s
r
e
o
u
a
n
l
d
a
:
r
F
m
r o
n
t
a
c
F
k
u
g
s
r
e
o
u
a
n
l
d
a
:
r
B
m
a
c
k
a
c
F
k
r
g
o
r
n
o
t
u
n
s
d
i
d
A
e
l
a
r
m
The following message is displayed, when the Background of
back side cannot be changed.
B
●AP-14
e
s
The following message is displayed, when the Background of
front side cannot be changed.
B
<Background fuse
error>
(Back side)
s
The following message is displayed, when the fuse for changing
the Background of back side blows out.
B
<Background fuse
error>
(Front side)
u
t
The following message is displayed, when the fuse for changing
the Background of front side blows out.
B
<Background fuse
alarm>
(Back side)
F
n
The following message is displayed, when the fuse for the lamp
for back side blows out.
B
<Background fuse
alarm>
(Front side)
o
a
c
B
k
a
g
c
r
k
o
u
s
n
i
d
d
e
A
l
a
r
m
<Hopper overrun>
The following message is displayed, when the hopper moves
over the normal position.
H
<Sensor control
error>
o
p
p
e
r
o
v
e
r
r
u
n
The following message is displayed, when an error occurs in the
sensor control.
S
e
n
s
o
A
r
l
a
C
r
o
m
n
t
r
o
l
<Sensor contamina- The following message is displayed, when an error occurs due
tion error>
to a contaminated sensor.
x
x
x
x
S
e
n
s
o
r
d
i
r
t
y
"xxxx." shows the sensor name (SUS, SF0, SA4, etc.)
HINT
<Sensor error>
The following message is displayed, when a sensor error occurs
x
x
x
x
S
e
n
s
o
r
e
r
r
o
r
"xxxx." shows the sensor name (SUS, SF0, SA4, etc.)
HINT
<Temprrature error> The following message is displayed, when the temperature
inside the scanner becomes higher than normal.
T
e
m
p
a
e
l
r
a
a
r
t
m
u
r
e
●AP-15
<Power supply
error>
The following message is displayed, when an error occurs in the
Power supply.
P
<EEPROM Alarm>
<VDCC Read/Write
error>
r
r
r
s
o
u
r
p
p
l
y
D
E
D
P
R
R
E
O
S
M
S
A
x
l
x
a
H
r
m
The following message is displayed, when an error occurs during accessing to the area of VDCC.
D
C
C
2
R
/
W
E
r
r
o
r
The following message is displayed when MDC time out error
occurs during initial diagnose process.
M
<Dither/Gamma
Read/Write error>
e
e
The EEPROM address where the error occurs is displayed in [xx] digit in the
above sample screen.
V
(MDC timeout)
w
The following message is displayed, when an error occurs in the
EEPROM.
A
E
HINT
o
D
T
C
i
m
e
o
u
t
The following message is displayed, when an error occurs during access to the Dither/Gamma RAM.
D
i
R
t
/
h e
W
r
E
/
r
G
r
a
o
m
r
m a
<Temporary memory The following message is displayed, when an error occurs durRead/Write error>
ing accessing to the temporary memory (RAM).
T
●AP-16
e
m
p
M
e
m
R
/
W e
r
r
o
r
<MDC download
error>
The following message is displayed, when an error occurs during downloading the firmware to MDC.
M
D
C
E
<Imprinter alarm>
<Command alarm>
d
r
o
r
w
o
n
r
l
o
a
d
The following message is displayed, when an error occurs in the
fi-486PRFR (Imprinter of front-side) or the fi-486PRRE
(Imprinter of rear-side).
I
P
m
r
p
e
r
i
n
t
e
r
A
l
a
r
m
I
P
m
o
p
s
r
t
i
n
t
e
r
A
l
a
r
m
The following message is displayed, when an error occurs in the
command sequence from PC.
(MDC command timeout 1)
C
o
m
m
a
n
d
E
r
r
o
r
1
(MDC command timeout 2)
C
o
m
m
a
n
d
E
r
r
o
r
2
(SDC command
sequence error)
C
o
m
m
a
n
d
E
r
r
o
r
3
(MDC response
error)
C
o
m
m
a
n
d
E
r
r
o
r
4
(SCSI response time
out)
C
o
m
m
a
n
d
E
r
r
o
r
5
●AP-17
●AP-18
INDEX
Pinch roller ........................... 3-20
Removable sheet guide ....... 3-29
Sensors ................................ 3-35
Separation roller .................. 3-10
SF0 sensor .......................... 3-37
SF1 sensor .......................... 3-37
SF1.5 sensor ....................... 3-39
SF2 sensor .......................... 3-39
Transport path ..................... 3-22
Cleaning materials ........................ 3-2
Cleaning sheet ....................... 3-2, 3-8
Configuration Window of FUJITSU
ISIS Scanner Driver .................. 1-38
Consumables ................................ 4-2
Abrasion counters........... 1-9, 4-3
Part No. .................................. 4-2
Replacement cycle ................ 4-2
Replacement message .......... 1-9
Correcting the skewed Documents 2-19
Cumulative lamp-on time ............ 4-19
A
ADF release lever ..........................3-5
ADF upper sheet guide ..................3-5
Adobe Acrobat ...............................2-3
B
Back-side lamp ........... 3-3, 3-47, 4-20
Basic Operations
Clearing errors ........................1-6
Inserting documents .............1-21
Lifting/lowering hopper ...........1-7
Loading documents ..............1-18
Operator Panel .......................1-6
Power off ................................1-4
Power on ................................1-2
Scanning documents ............1-23
Setting the Hopper ...............1-14
Setting the Stacker ...............1-15
Setup mode ..........................1-10
Test mode.............................1-10
Waking up, Power Save .........1-5
Basic Scanner Operations .............1-1
Batch counter .................................4-3
Brake roller ............................3-3, 3-14
Brake roller unit ............................4-12
C
Cleaner F1 .....................................3-2
Cleaner F2 ............................3-2, 3-19
Cleaning
Brake roller ...........................3-14
Cleaning sheet .......................3-8
Discharge brush ...................3-24
Document width sensor........3-35
Feed roller ............................3-18
Glass sheet guide.................3-32
Glass surface .......................3-29
Lamps ...................................3-41
Pad ..................................3-5, 3-7
Pick Roller ............................3-10
D
Daily Care...................................... 3-1
Detecting Double-Feeds ............. 2-17
Dimensions............................. 9-4, 9-6
Discharge brush ................... 3-3, 3-24
Document
Document quality ................... 6-3
Document size ....................... 6-2
Document thickness .............. 6-3
Document type ...................... 6-3
Grounding color area ............. 6-8
Hole-punching, area .............. 6-6
Hopper capacity ................... 6-10
Job separation sheet ............. 6-9
Precautions ............................ 6-4
Print Prohibited Area ............. 6-7
Document jams ............................. 5-2
Document separation, adjustment 5-5
Document width sensor ....... 3-3, 3-35
Dropout color ............................... 2-13
●IN-1
E
M
Errors ............................................. 1-6
Magnet catch ...............................1-21
Manual Feed Mode ......................1-21
F
Feed roller .............................3-3, 3-18
fi-486PRFR .............................8-2, 8-3
fi-486PRRE ......................8-2, 8-4, 8-5
Front-side lamp ............3-3, 3-41, 4-15
FUJITSU ISIS Scanner Driver ..... 1-34
FUJITSU TWAIN32 Scanner
Driver ......................................... 1-27
O
Offline setup mode .........................7-2
Online setup mode .........................7-2
Operator panel ........................1-6, 4-3
P
Pad ..........................................3-3, 3-5
Pad ASSY ......................................4-4
PDF ................................................2-3
Pick roller .................... 1-21, 3-3, 3-10
Pick roller unit ................................4-9
Pinch roller ............................3-3, 3-20
Power button ..................................1-3
Power off ........................................1-4
Power on ........................................1-2
Power Save Mode .........................1-5
G
Glass sheet guide .................3-3, 3-32
Glass surface ............................... 3-29
Guide plate ...........................1-22, 3-6
H
Hopper ............... 1-7, 1-14, 1-18, 1-21
Hopper extension ........................ 1-20
How to use the Scanner Driver ... 1-27
R
I
Installation Specifications
Ambient condition .................. 9-5
Dimensions ............................ 9-4
Input power ............................ 9-4
Power consumption ............... 9-4
Space requirements ............... 9-4
Weight .................................... 9-4
Isopropyl alcohol ............................ 3-2
L
Labels on the scanner ................. 5-32
Lamp
Lamp socket ................3-44, 3-48
Lamp socket cover ............... 3-44
LCD ................................................ 1-9
Lifting or lowering the hopper ........ 1-7
●IN-2
Removable sheet guide ........3-3, 3-29
Replacing
Back-side lamp .....................4-20
Brake roller unit ....................4-12
Front-side lamp ....................4-15
Pad ASSY...............................4-4
Pick roller unit .........................4-9
S
ScandAll 21 .........................1-23, 1-26
Scanner Specifications ..................9-1
Scanning documents ...................1-23
Different-size ..........................2-2
Dropout .................................2-13
PDF.........................................2-3
Sensors ........................................3-35
Separation roller....................3-3, 3-10
Service provider ...........................5-30
Setting Window for FUJITSU
TWAIN32 Scanner Driver ..........1-31
Setup mode ...........................1-10, 7-2
Details ...................................7-17
Function of buttons .................7-4
Outline ....................................7-2
Transitions, screens ...............7-4
SF0 sensor ............................3-3, 3-37
SF1 sensor ............................3-3, 3-37
SF1.5 sensor .........................3-3, 3-39
SF2 sensor ............................3-3, 3-39
Side cover ....................................3-47
Side guides .........................1-19, 1-22
Skipping blank Pages ..................2-15
Specifications .................................9-2
ADF capacity ..........................9-2
Document thickness ...............9-2
Grayscale level .......................9-2
Image sensor ..........................9-2
Interface..................................9-2
Light source ............................9-2
Optical resolution....................9-2
Other functions .......................9-2
Output mode ...........................9-2
Output resolution ....................9-2
Scanner Type .........................9-2
Scanning area ........................9-2
Scanning speed......................9-2
Stacker ................................1-15, 1-16
Stacker Extension ........................1-17
Stopper.........................................1-17
T
Test mode ...........................1-10, 7-64
Button functions....................7-65
Contents, setting ..................7-69
Details ...................................7-70
Transition, screens ...............7-65
Transport path.......................3-3, 3-22
TWAIN Driver ...............................1-25
●IN-3
●IN-4
fi-4860C Image Scanner Operator’s Guide
P3PC-E167-05EN
Date published: March, 2005
PFU LIMITED
•Copying
of the contents of this manual in whole or in part and copying of the scanner
application is forbidden under the copyright law.
•The
•PFU
contents of this manual are subject to change without notice.
LIMITED assumes no liability for incidental or consequential damages arising
from the use of this manual, and any claims by a third party.
Download PDF

advertising