Fujitsu GBR-222200-002 Tablet User Manual

Osian_UG.book Page i Monday, October 9, 2006 1:24 PM
Fujitsu Stylistic
ST5111 / ST5112
Tablet PC
®
User’s Guide
Osian_UG.book Page ii Monday, October 9, 2006 1:24 PM
Osian_UG.book Page iii Monday, October 9, 2006 1:24 PM
Copyright
Copyright and Trademark Information
Fujitsu Computer Systems Corporation has made every
effort to ensure the accuracy and completeness of this
document. Because ongoing development efforts are
made to continually improve the capabilities of our products, however, the data contained herein represents
Fujitsu design objectives and is provided for comparative
purposes; actual results may vary based on a variety of
factors. This product data does not constitute a warranty.
Specifications are subject to change without knowledge.
Fujitsu and the Fujitsu logo are registered trademarks of
Fujitsu Limited; Stylistic is a registered trademark of
Fujitsu Computer Systems Corporation.
Microsoft and Windows are registered trademarks or
trademarks of Microsoft Corporation in the United
States and/or other countries.
PCMCIA and CardBus are registered trademarks of the
Personal Computer Memory Card International Association.
Centrino, Intel, and Intel Core are trademarks or registered
trademarks of Intel Corporation or its subsidiaries in the
United States and other countries.
OmniPass is a trademark of Softex, Inc.
Adobe, Acrobat, and Acrobat Reader are either registered
trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.
SigmaTel is a registered trademark of SigmaTel, Inc.
Bluetooth and the Bluetooth logo are registered trademarks of Bluetooth SIG, Inc.
Memory Stick is a registered trademark of Sony Corporation and/or its affiliates
Wi-Fi is a trademark of the Wireless Ethernet Compatibility Alliance (WECA).
All other products are trademarks or registered trademarks of their respective companies.
Warning
Handling the cord on this product will expose
you to lead, a chemical known to the State of
California to cause birth defects or other
reproductive harm.
Wash hands after handling.
Copyright 2006 Fujitsu Computer Systems Corporation.
All rights reserved. No part of this publication may be
copied, reproduced, or translated, without the prior
written consent of Fujitsu Computer Systems
Corporation. No part of this publication may be stored
or transmitted in any electronic form without the prior
consent of Fujitsu Computer Systems Corporation.
B5FJ-1391-01EN-00
Atheros and Super AG are registered trademarks of
Atheros Communications, Inc.
DECLARATION OF CONFORMITY
according to FCC Part 15
Responsible Party Name:
Address:
Telephone:
Declares that product:
Fujitsu Computer Systems Corporation
1250 E. Arques Avenue, MS 122
Sunnyvale, CA 94085
408-746-6000
Model Series: Stylistic® ST5111 Tablet PC
Stylistic® ST5112 Tablet PC
Complies with Part 15 of the FCC Rules
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and, (2) This device must accept any interference
received, including interference that may cause undesired operation.
Note: For more detailed information about the FCC rules and their applicability to the Stylistic ST5100 Series
Tablet PC, refer to Chapter 5 of this document.
Osian_UG.book Page iv Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC - User’s Guide
IMPORTANT SAFETY INSTRUCTIONS
■
For Authorized Repair Technicians Only
This unit requires an AC adapter to operate. Use only
UL Listed Class 2 Adapters with an output rating of 16
VDC, with a current of 3.75A minimum.
AC Adapter output polarity:
+
■
When using your notebook equipment, basic safety
precautions should always be followed to reduce the
risk of fire, electric shock and injury to persons,
including the following:
■
■
■
■
■
■
Do not use this product near water for example,
near a bathtub, washbowl, kitchen sink or laundry
tub, in a wet basement or near a swimming pool.
Avoid using the modem during an electrical storm.
There may be a remote risk of electric shock from
lightning.
Do not use the modem to report a gas leak in the
vicinity of the leak.
Use only the power cord and batteries indicated in
this manual. Do not dispose of batteries in a fire.
They may explode. Check with local codes for
possible special disposal instructions.
To reduce the risk of fire, use only No. 26 AWG or
larger UL Listed or CSA Certified Telecommunication Line Cord
For TV Tuner Models: To protect from overvoltages
and transients on the Cable Distribution System, make
sure that the outer shield of the coaxial cable is connected to earth (grounded) at the building premises as
close to the point of cable entrance as practicable, as
required per NEC Article 820.93, ANSI/NFPA 70:
2005. If you have questions about your CATV installation, contact your service provider.
SAVE THESE INSTRUCTIONS
Danger of explosion if Lithium (clock) battery is incorrectly replaced. Replace only
with the same or equivalent type recommended by the manufacturer. Dispose of
used batteries according to the manufacturer’s instruction.
For continued protection against risk of
fire, replace only with the same type and
rating fuse.
System Disposal
LAMP(S) INSIDE THIS PRODUCT
Hg CONTAIN MERCURY AND MUST
BE RECYCLED OR DISPOSED OF
ACCORDING TO LOCAL, STATE, OR
FEDERAL LAWS.
Osian_UG.book Page i Monday, October 9, 2006 1:24 PM
Ta b l e o f C o n t e n t s
Fujitsu Stylistic® ST5100 Tablet PC
Table of Contents
PREFACE
About This Guide . . . . . . . . . . . . . . . . . . . . . . . . .vii
Fujitsu Contact Information . . . . . . . . . . . . . . . . .vii
Limited Warranty Information . . . . . . . . . . . . . . .vii
1
GETTING STARTED
WITH YOUR TABLET PC
25
25
26
26
26
27
27
28
28
29
3
Getting Started with Your Tablet PC
In-box Items for the Stylistic Tablet PC. . . . . . . . . 1
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . 1
Stylistic Tablet PC Features. . . . . . . . . . . . . . . . . . 2
Status Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Application Buttons . . . . . . . . . . . . . . . . . . . . . . . 9
Navigation Buttons. . . . . . . . . . . . . . . . . . . . . . . 11
Tertiary Functions of Buttons . . . . . . . . . . . . . . . 12
Security Functions of Application Buttons. . . . . . 13
Setting up the Security Panel . . . . . . . . . . . . . . . 13
Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Using Your Security Panel . . . . . . . . . . . . . . . . . 14
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Uninstalling the Security Panel Application . . . . . 14
Connectors and Peripheral Interfaces . . . . . . . . . 16
2
CARING FOR YOUR TABLET PC
Care and Maintenance
Caring for Your Tablet PC . . . . . . . . . . . . . . . . .
Protecting the Display Screen. . . . . . . . . . . . . . .
Storing the Tablet PC. . . . . . . . . . . . . . . . . . . . .
Avoiding Overheating . . . . . . . . . . . . . . . . . . . .
Cleaning the Display Screen . . . . . . . . . . . . . . . .
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . .
Restoring the Pre-Installed Software . . . . . . . . .
Restoring the Factory Image . . . . . . . . . . . . . . .
Automatically Downloading Driver Updates. . . .
33
33
34
34
35
35
36
36
37
4
SYSTEM SPECIFICATIONS
USING YOUR TABLET PC
System Hardware Specifications
Using the ST5100 Series Tablet PC
System States . . . . . . . . . . . . . . . . . . . . . . . . . . .
Powering Up the Tablet PC . . . . . . . . . . . . . . . .
Shutting Down the System. . . . . . . . . . . . . . . . .
Suspending System Operation . . . . . . . . . . . . . .
Resuming System Operation . . . . . . . . . . . . . . .
Using the Shock Sensor Utility . . . . . . . . . . . . . .
Adjusting the Display Brightness. . . . . . . . . . . . .
Using the Pen. . . . . . . . . . . . . . . . . . . . . . . . . . .
Calibrating the Pen . . . . . . . . . . . . . . . . . . . . . .
Installing a Pen Tether . . . . . . . . . . . . . . . . . . . .
Replacing the Pen Tip . . . . . . . . . . . . . . . . . . . .
Charging the Battery . . . . . . . . . . . . . . . . . . . . .
Removing and Installing the Battery. . . . . . . . . .
Tips for Conserving Battery Power . . . . . . . . . . .
Modem Connection . . . . . . . . . . . . . . . . . . . . .
Memory Stick/SD Card Slot . . . . . . . . . . . . . . . .
PC Card Slot . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing and Installing Memory . . . . . . . . . . .
21
22
22
22
23
23
24
24
Processing Specifications . . . . . . . . . . . . . . . . . .
Memory/Storage Specifications . . . . . . . . . . . . .
Display Specifications. . . . . . . . . . . . . . . . . . . . .
Physical Specifications . . . . . . . . . . . . . . . . . . . .
Interface Specifications . . . . . . . . . . . . . . . . . . .
Power Specifications . . . . . . . . . . . . . . . . . . . . .
Environmental Specifications . . . . . . . . . . . . . . .
Agency Approval Specifications . . . . . . . . . . . . .
Additional Specifications . . . . . . . . . . . . . . . . . .
41
41
41
41
41
42
42
42
42
Osian_UG.book Page ii Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide
Regulatory Information
Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
APPENDIX A: WIRELESS LAN/
BLUETOOTH USER’S GUIDE
Before Using the Wireless LAN
For better communications. . . . . . . . . . . . . . . . . 49
Stopping transmission . . . . . . . . . . . . . . . . . . . . 49
Starting Transmission . . . . . . . . . . . . . . . . . . . . . 50
Connecting the WLAN
Flow of operations . . . . . . . . . . . . . . . . . . . . . . . 51
Preparation for wireless LAN connection . . . . . . 51
Connection to the network . . . . . . . . . . . . . . . . 53
APPENDIX B: SECURITY
DEVICE USER’S GUIDE
Fingerprint Sensor Device
Introducing the Fingerprint Sensor Device . . . . .
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . .
Installing OmniPass . . . . . . . . . . . . . . . . . . . . . .
User Enrollment . . . . . . . . . . . . . . . . . . . . . . . . .
Using OmniPass. . . . . . . . . . . . . . . . . . . . . . . . .
Configuring OmniPass . . . . . . . . . . . . . . . . . . . .
OmniPass Control Center . . . . . . . . . . . . . . . . .
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . .
67
67
67
68
69
71
72
74
Trusted Platform Module Installation
TPM Installation. . . . . . . . . . . . . . . . . . . . . . . . . 74
Other settings
Index
Setting of power-saving function . . . . . . . . . . . . 57
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Troubleshooting the WLAN
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 58
Wireless LAN Glossary
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
IP address information
Additional information . . . . . . . . . . . . . . . . . . . . 62
WLAN Specifications
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Using the Bluetooth Device
What is Bluetooth?. . . . . . . . . . . . . . . . . . . . . . . 64
Where to find information about Bluetooth . . . . 64
Osian_UG.book Page v Monday, October 9, 2006 1:24 PM
Preface
Osian_UG.book Page vi Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Preface
Osian_UG.book Page vii Monday, October 9, 2006 1:24 PM
Preface
Preface
ABOUT THIS GUIDE
The Stylistic® ST5100 Series Tablet PC is a highperformance, pen-based computer that has been
designed to support Microsoft®Windows® XP Tablet PC
Edition.
This manual explains how to operate your Fujitsu
Stylistic ST5100 Series Tablet PC hardware and built-in
system software.
The Stylistic ST5100 Series Tablet PC is a completely selfcontained unit with an active-matrix (TFT) color
indoor-outdoor LCD display and an active digitizer. It
has a powerful interface that enables it to support a
variety of optional features.
FUJITSU CONTACT INFORMATION
Service and Support
You can contact Fujitsu Service and Support in the
following ways:
■
■
■
Before you place the call, you should have the
following information ready so the customer support
representative can provide you with the fastest possible
solution:
■
■
■
■
■
Conventions Used in the Guide
Keyboard keys appear in brackets.
Example: [Fn], [F1], [ESC], [ENTER] and [CTRL].
Pages with additional information about a specific topic
are cross-referenced within the text.
Example: (See page xx.)
On screen buttons or menu items appear in bold
Example: Click OK to restart your Tablet PC.
The information icon highlights
information that will enhance your
understanding of the subject material.
The caution icon highlights information
that is important to the safe operation of
your computer, or to the integrity of your
files. Please read all caution information
carefully.
Toll free: 1-800-8Fujitsu (1-800-838-5487)
E-mail: 8fujitsu@us.fujitsu.com
Website:
http://www.computers.us.fujitsu.com/support
■
■
Product name
Product configuration number
Product serial number
Purchase date
Conditions under which the problem occurred
Any error messages that have occurred
Type of device connected, if any
Fujitsu Online
You can go directly to the online Fujitsu product catalog
for your Stylistic Tablet PC by clicking on the Fujitsu
Weblinks -> LifeBook Accessories website link, located in
the Windows Start -> All Programs menu.
You can also reach Fujitsu Service and Support on-line by
clicking on the Fujitsu Weblinks -> Fujitsu Service and
Support website link, located in the Service and Support
Software folder of the Windows Start -> All Programs
menu..
You must have an active internet connection to use the online URL links.
LIMITED WARRANTY INFORMATION
The warning icon highlights information
that can be hazardous to either you, your
computer, or your files. Please read all
warning information carefully.
Your Stylistic ST5100 Series Tablet PC is backed by an
International Limited Warranty. Check the service kit
that came with your system for warranty terms and
conditions.
Osian_UG.book Page viii Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Preface
Osian_UG.book Page ix Monday, October 9, 2006 1:24 PM
1
Getting Started
with Your Tablet PC
Osian_UG.book Page x Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section One
Osian_UG.book Page 1 Monday, October 9, 2006 1:24 PM
Getting Started
Getting Started with Your Stylistic Tablet PC
The Stylistic ST5100 Series Tablet
PC is available with either a 10.4”
reflective display or a 12.1” transmissive
display. For purposes of illustration, the 12.1”
model is used throughout this document. Please
refer to the Specifications chapter for additional details.
Figure 1-1. Stylistic ST5100 Series Tablet PC
The Stylistic® ST5100 Series Tablet PC is a highperformance, pen-based computer that has been
designed to support Microsoft® Windows® XP Tablet PC
Edition 2005. This chapter provides an overview of the
Stylistic ST5100 Series Tablet PC and its features.
IN-BOX ITEMS FOR THE STYLISTIC
ST5100 SERIES TABLET PC
OPTIONAL ACCESSORIES
There are many optional accessories that can be used
with the Stylistic ST5100 Series Tablet PC. For the latest
list of accessories available for your Tablet PC, be sure to
check the Fujitsu shopping website at: www.shopfujitsu.com. Refer to the instructions provided with these
accessories for details on their use.
Verify that the following items are included in the box
with your Tablet PC:
• Stylistic ST5100 Series active pen
• Pen tips (quantity: 5)
• Pen tip removal tool
• Pen tether
• Main battery
• Power cord
• AC adapter
• Screen protectors (quantity: 2)
• Getting Started Guide
• Quick Tips Guide
• Drivers and Application Restore (DAR) DVD
• System Restore DVD
1
Osian_UG.book Page 2 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section One
STYLISTIC TABLET PC FEATURES
Features and controls that you use to operate the Stylistic ST5100 Series Tablet PC are outlined below and illustrated in
Figures 1-1 through 1-6. Details on using these features and controls are provided later in this manual.
Infrared Keyboard/Mouse Port
2nd Built-in Microphone
(12.1” model only)
Speaker
Fingerprint Swipe Sensor
(12.1” model only)
System Status LEDs
Display
Power On/Suspend/
Resume Button
Application/Security Buttons
Built-in Microphone
Infrared Keyboard/Mouse Port
Navigation Buttons
Figure 1-2. Stylistic ST5100 Series Tablet PC Features (Front View)
Front Features:
1
system’s current state. To determine the current system
state, observe the Power icon in the Status display.
Table 2-1 on page 21 gives the different system states
represented by the Power icon and describes how you
can change the system state from the current state. on
page 22 for more information.)
• Infrared keyboard/mouse ports: The infrared ports
are used for communicating with a proprietary
infrared keyboard or mouse.†
• Speaker: Allows you to listen to mono audio files.
• Fingerprint Swipe Sensor: The optional fingerprint
swipe sensor allows you to start your system by
swiping your finger over the sensor. (See Fingerprint
Sensor Device on page 67 for more information.)
• Application buttons: Allow you to quickly launch
pre-defined applications, utilities, and security
features by pressing a button. (See Application
Buttons on page 9 for more information.)
• System status LEDs: Indicate the operational status
of the Tablet PC and hard disk drive, the charge level
of the battery, and the security panel. (See Status
Display on page 7 for more information.)
• Navigation buttons: The navigation buttons allow
you to move: Page Up/Page Down, Tab Right/Tab
Left, Cursor Up/Cursor Down, and Cursor Right/
Cursor Left. (See Navigation Buttons on page 11 for
more information.)
• Power On/Suspend/Resume button: Allows you to
turn on, off, standby, resume, hibernate or wake the
Tablet PC in order to optimize battery life. (See When
you use your Tablet PC, you can change the current
system state in a number of ways, depending on the
2
• Built-in Microphones: The built-in microphone(s)
allow you to input mono audio. Note that the 10.4”
model has one microphone; the 12.1” model has two.
†
These peripherals and accessories are sold separately.
Osian_UG.book Page 3 Monday, October 9, 2006 1:24 PM
Getting Started
Memory
Module Cover
System Interface
Connector
Battery
Battery Release Latch
Tablet Dock
Latch Points
Thermal Suede
Wireless LAN*
On/Off Switch
Figure 1-3. Stylistic ST5100 Series Tablet PC Features (Back View)
Back Features:
1
• Memory module cover: Removable cover over the
memory modules. (See Removing and Installing
Memory on page 29 for more information.)
• System interface connector: Allows you to connect
the optional Stylistic Tablet Dock.†
• Removable battery: Can be removed and replaced
with a charged battery.† (See Removing and Installing
the Battery on page 26 for more information.)
• Battery release latch: Used to release the removable
battery.
• Tablet Dock latch point: Allows you to attach the
system to an optional Tablet Dock.†
• Thermal Suede: Several areas of the system back are
covered with “thermal suede”. This material should
not be removed. It is designed to minimize the heat
that the user feels when the system has been operating
for an extended period of time.
• Wireless LAN module cover: Provides protection for
the optional wireless LAN radio. (See Connecting the
WLAN on page 51 for more information.)
• Wireless LAN/Bluetooth On/Off switch: For systems
with the optional wireless LAN radio or Bluetooth
device, this switch toggles the radio on or off. (See
Using the Bluetooth Device on page 64 for more
information.)
†
These peripherals and accessories are sold separately.
3
Osian_UG.book Page 4 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section One
Pen Holder
Pen Tether Point
PC Card Slot
PC Card Eject Button
Air flow vents
SD Card/Memory Stick Slot
IrDA/FIR Port
Smart Card Slot
Figure 1-4. Stylistic ST5100 Series Tablet PC Features (Top View)
Top Features:
1
To protect your notebook from damage
and to optimize system performance, be
sure to keep all air all vents unobstructed,
clean, and clear of debris. This may
require periodic cleaning, depending upon
the environment in which the system is
used.
• Pen: The main input device that you use to execute
programs and enter data. A pen holder is built into
the Tablet PC to store the pen when not in use. (See
Using the Pen on page 24 for more information.)
• Pen Tether Point: The pen tether point is used to
attach a pen tether to help prevent loss of the pen.
(See Installing a Pen Tether on page 25 for more
information.)
• PC Card slot: Allows you to insert a Type I or Type II
PCMCIA Card† in the system. (See PC Card Slot on
page 28 for more information.)
• PC Card Eject Button: The PC Card eject button is
used to remove a PC Card from the PC Card slot.
• IrDA/FIR port: Provides an infrared interface for
communication with devices compliant with IrDA
Standard Revision 1.1.
• Air flow vents: Provides secondary cooling for
processor.
Do not operate the notebook in areas
where the air vents can be obstructed,
such as in tight enclosures or on soft
surfaces like a bed or cushion.
• SD Card/Memory Stick Slot: The Secure Digital
(SD) card/Memory Stick slot allows you to insert a
flash memory card† for data storage. Flash memory
cards allow you to transfer data to and from a variety
of different digital devices. (See Memory Stick/SD
Card Slot on page 28 for more information.)
• Smart Card Slot: The dedicated Smart Card slot
allows you to insert a Smart Card† on which you can
store such data as medical information or electronic
“cash”.
†
4
These peripherals and accessories are sold separately.
Osian_UG.book Page 5 Monday, October 9, 2006 1:24 PM
Getting Started
External Monitor Connector (behind cover)
IEEE 1394 Jack
LAN Jack
Microphone Jack
Modem Jack
Lock Slot
Headphone Jack
USB 2.0 Ports
DC Input Jack
Latch Point
Figure 1-5. Stylistic ST5100 Series Tablet PC Features (Left Side View)
Left-Side Features:
1
• USB 2.0 ports: Allow you to connect Universal Serial
Bus-compliant devices (compliant with USB
Standard Revision 2.0) to the Tablet PC. Additional
USB ports are located on the optional Tablet Dock†.
connector to the Tablet PC’s internal 56 Kbps
modem. Note that the internal 56 Kbps modem
module installed in the Stylistic ST5100 Series Tablet
PC has actual maximum transfer rates of 53 Kbps
(receive), 33.6 Kbps (send), and 14.4 Kbps (fax).
Download rates are limited to 53 Kbps in the United
States due to FCC restrictions. (See Modem
Connection on page 27 for more information.)
• Headphone Jack: Allows you to connect a set of stereo
headphones†.
• Microphone Jack: Allows you to connect an external
microphone†.
• IEEE 1394 Jack: Allows you to connect IEEE 1394
(Firewire) peripherals such as digital video cameras†
or external hard drives† to your Tablet PC.
• External Monitor Connector: The External Monitor
connector allows you to connect an external VGA,
XGA, or SVGA monitor.
• Latch Point: Used in conjuction with the optional
Tablet Dock to secure system to dock.
• LAN jack: Allows you to connect a standard RJ-45
connector to the Tablet PC’s internal local area
network (LAN).
• Lock slot: Allows you to attach a compatible security
cable.†
• DC input connector: Allows you to connect the AC
adapter or auto adapter.†
†
These peripherals and accessories are sold separately.
• Modem jack: Allows you to connect a standard RJ-11
5
Osian_UG.book Page 6 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section One
Infrared Keyboard/Mouse Port
Optional Wireless LAN location
Pen / Pen Holder
Latch Point
Figure 1-6. Stylistic ST5100 Series Tablet PC Features (Right Side View)
Right-Side Features:
1
• Pen: The main pointing device that you use to
execute programs and enter data. A pen holder is
built into the Tablet PC to store the pen when not in
use.
• Infrared keyboard/mouse port: The infrared port
wraps around the front and bottom of the display,
and is used for communicating with an optional
proprietary infrared keyboard or mouse†.
• Latch Point: Used in conjuction with the optional
Tablet Dock to secure system to dock.
• Wireless LAN location: The optional wireless LAN
device is located inside of the system housing. (See
Connecting the WLAN on page 51 for more
information.)
†
6
These peripherals and accessories are sold separately.
Osian_UG.book Page 7 Monday, October 9, 2006 1:24 PM
Getting Started
STATUS DISPLAY
Icons appear under each of the system status LEDs in the
status display indicating the status of system functions
such as system power and battery charge level. The location of icons in the Status display is shown in Figure 1-7.
Table 1-1. explains how the LEDs associated with the
individual icons are displayed, and describes what the
variations of that display indicate. (If an icon is not
displayed, it indicates that the related system function is
off or inactive.
Power
Security
Battery
Charge/DC In
Figure 1-7.
HDD Access
Status Display Icons
In the following table, a “blinking” LED flashes at the rate of once per second; an LED that is “blinking, slow” flashes at the
rate of one second on, five seconds off.
Icon
Power
Mode/State
• On State
LED State
Remarks
Green, continuous
The system is powered on and ready for use.
• Standby
Green, blinking
The system has suspended and saved active
settings to RAM.
• Off State
Off
The system has suspended and saved settings
and data to the hard disk drive.
Amber
AC adapter and battery are available and system
is charging.
• Idle Mode
• Hibernate
Charge/DC
In
• On State
• Idle Mode
• Standby
Green
• Hibernate
• AC adapter and battery are available and
system is not charging (battery fully
charged).
• AC adapter is available but battery is not
present.
• Off State
Amber, blinking
AC adapter and battery are available and waiting
to charge (battery is out of thermal range).
Off
AC adapter is not available.
7
Osian_UG.book Page 8 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section One
In the following table, a “blinking” LED flashes at the rate of once per second; an LED that is “blinking, slow” flashes at the
rate of one second on, five seconds off.
Icon
Battery
Mode/State
LED State
Remarks
• On State
Green, continuous
Battery charge is between 50%-100%
• Idle Mode
Amber, continuous
Battery charge is between 13%-49%
Red, continuous
Battery charge is between 0%-12%
Red, blinking
There is a battery error.
Green, blinking slow
Battery charge is between 50%-100%.
Amber, blinking slow
Battery charge is between 13%-49%.
Red, blinking slow
Battery charge is between 0%-12%.
Off
Battery is not installed, or system is off or in
Hibernate mode.
• Standby,
without AC adapter
• Standby with AC
adapter
• Hibernate,
with AC adapter
• Off State
• Hibernate,
without AC adapter
HDD Access
• On State (or
flashing)
If battery is inserted during power off, LED blinks
amber for 4 seconds to detect battery. Battery
status is displayed for 5 seconds after that.
Green
Displayed when hard disk drive is accessed.
Off
Hard disk drive is not being accessed.
Green, continuous
(until password is
entered)
The Security Indicator lights (if a password was
set) when the system resumes from Off or
Standby modes. You must enter the password
that was set in the Security Panel before your
system will resume operation. (See Security
• Idle Mode
• Standby
• Hibernate
• Off State
Security
• On State
Functions of Application Buttons on page 13 for
more information.)
Table 1-1. System Status Indicators
8
Osian_UG.book Page 9 Monday, October 9, 2006 1:24 PM
Getting Started
APPLICATION BUTTONS
The six application buttons are located on the upper
right-hand side of a vertically-oriented system. . Five of
the buttons have secondary functions. The secondary
functions are activated by pressing the Function (Fn)
button while pressing the application button.
Ctl-Alt-Del
The buttons also have separate tertiary functions that can
be used while the system is booting up. For more information about the tertiary functions, refer to Table 1-4 on
page 12.
Ctl-Alt-Del is the only application button
that can be used while the system is
logging on or when the system is locked
(i.e., when you have the Logon or
Computer Locked window showing on
your desktop).
Button Icon
and Name
Primary)
Tablet Icon
(Fn +
Button)
(Secondary)
EMail
Orientation
Escape
Enter
Function
Figure 1-8. Application Buttons
Description
Pressing the Ctl-Alt-Del button for approximately one second allows you to log on
after boot or after resuming from power management. Holding the button down for
approximately two seconds causes it to act as if Ctl-Alt-Del had actually been entered
from a keyboard.
Ctl-Alt-Del
Button
Security
Button
Security Button: All five buttons are used when implementing security functions. Four
of the buttons are used to enter the password, and the fifth is used as an Enter button.
See “Security Functions of Application Buttons” on page 13.
When you press the EMail button, you automatically launch Microsoft Outlook
Express, where you can read, create, and send emails.
EMail
Button
Internet
Button
When you press the Fn + EMail buttons at the same time, you automatically launch
the Web browser. The default page to which you go is the Fujitsu home page. If you
would like to change your home page, go to the Control Panel-> Internet Options.
Select the General tab and enter the starting address you would like to use.
When you press the Orientation button, the system screen orientation changes from
portrait (vertical) to landscape (horizontal) or from landscape to portrait. When you
would like to use the Tablet PC as an eBook, for example, you would use the portrait
orientation, when accessing spreadsheets, you would more typically use a landscape
orientation.
Orientation
Button
Display Mode
Button
When you press the Fn + Orientation buttons at the same time*, the display output
will switch between internal, external, and simultaneous display.
The Escape application button acts the same way as an Escape key on a keyboard.
Escape
Button
Application A
Button
When you press the Fn + Esc buttons at the same time*, they act to invoke a predetermined application or generate a combination keystroke, as assigned in the Tablet
Button Settings utility. (You can change the settings in Control Panel -> Tablet Button
Settings).
By default, pressing the Fn + Esc combination acts the same as if you had pressed Ctl
+ Esc on a keyboard: the Start menu is launched.
9
Osian_UG.book Page 10 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section One
Button Icon
and Name
Primary)
Tablet Icon
(Fn +
Button)
(Secondary)
Description
The Enter application button acts the same way as an Enter key on a keyboard.
Pressing the Fn + Ent buttons at the same time*, acts to invoke a pre-determined
application or keystroke combination, as assigned in the Tablet Button Settings utility.
(You can change the settings in Control Panel -> Tablet Button Settings).
Enter Button
Application B
Button
By default, pressing the Fn + Ent combination acts the same as if you had pressed Alt
on a keyboard: it selects a main menu in the typical Windows application.
The Function button works in conjunction with the other application buttons to
provide additional functionality for the buttons. Refer to specific details above.*
Fujitsu Menu
Utility
Function
Button
Pressing the Fn button twice in succession (within the “sticky” time*), causes the
Fujitsu menu to appear on your screen, allowing you to modify certain system
settings.
Table 1-2. Application Buttons - Primary and Secondary Functions
* The Fn button has a handy “sticky” feature that allows you to press two buttons in immediate succession, rather
than at exactly the same time. After pressing the Fn button, you have a short time (2 to 3 seconds) to press the
second button.
10
Osian_UG.book Page 11 Monday, October 9, 2006 1:24 PM
Getting Started
NAVIGATION BUTTONS
The two navigation buttons are located on the lower
right-hand side of a vertically-oriented system. Each of
the buttons can be toggled by pressing either end of the
button.
The buttons have dual functions. The secondary functions are activated by pressing the Function (Fn) button
while pressing the application button*.
The buttons also have separate tertiary functions that can
be used while the system is booting up. For more information about the tertiary functions, refer to Table 1-4 on
page 12.
Ctl-Alt-Del is the only Application button
that can be used while the system is
logging on or when the system is locked
(i.e., when you have the Logon or
Computer Locked window showing on
your desktop).
Buttons/icons
Purpose (when pressed alone)
(“Primary” function)
This button consists of Page Up and Page
Down segments. When the Page Up
portion is pressed, you will scroll up one
page.
Navigation Buttons
Figure 1-9. Navigation Button Location
Purpose (when pressed with Fn button)
(“Secondary” function)
When pressed with the Function (Fn) button*, the
Up portion of this button allows you to tab right.
When pressed with the Function (Fn) button*, the
Down portion of this button allows you to tab left.
When the Page Down portion is pressed,
you will scroll down one page.
This button consists of Up and Down
segments. When the Up portion is
pressed, the cursor will move up.
When pressed with the Function (Fn) button*, the
Up portion of this button will move the cursor to the
right.
When the Down portion is pressed, the
cursor will move down.
When pressed with the Function (Fn) button*, the
Down portion of this button will move the cursor to
the left.
* The Fn button has a handy “sticky” feature that allows you to press two buttons in immediate succession, rather
than at exactly the same time. After pressing the Fn button, you have a short time (2 to 3 seconds) to press the
second button.
Table 1-3. Navigation Buttons
11
Osian_UG.book Page 12 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section One
TERTIARY FUNCTIONS OF APPLICATION AND NAVIGATION BUTTONS
While you are booting up your system, the Application
Buttons and Navigation buttons can be used for entering
and navigating through the Basic Input-Output System
(BIOS), and for invoking the Advanced Options Menu,
where you can enter different modes (such as Safe
Mode).
The BIOS is a program and a set of parameters that are
stored in ROM, which tests and operates your Tablet PC
from when you turn it on until it loads your installed
Buttons/icons
operating system from disk. Information from the BIOS
is transferred to the operating system to provide it with
information on the configuration and status of the hardware.
The system is booting up while the Fujitsu logo is
displayed immediately after turning on the system. The
table below indicates how the buttons act while the
system is booting up and while you are in the BIOS.
Purpose (when pressed while the system is booting up)
Pressing the Ctl-Alt-Del button while the system is booting up takes you into BIOS setup. This is
the same as if you had tapped [F2] on a keyboard.
Ctl-Alt-Del Button
Pressing the EMail button while the system is booting up opens the Boot Options menu. This is
the same as if you had tapped [F12] on a keyboard.
EMail Button
Pressing the Orientation button while the BIOS setup screen is open causes the selected item (if
applicable) to change to the next item. Pressing this is the same as tapping the spacebar on a
keyboard.
Orientation Button
Pressing the Esc button while the BIOS is open acts to escape from the BIOS. This is the same as if
you had tapped [Esc] on a keyboard.
Escape Button
Pressing the Ent button while the BIOS is open acts the same as the [Ent] button on a keyboard.
Enter Button
Function Button
Pressing the Fn button while the system is displaying the operating system boot menu, opens the
Advanced Operating System Options menu. This menu allows you to enter different operating
system modes (such as Safe Mode). Pressing this button is the same as if you had tapped [F8] on
a keyboard.
Pressing the top half of the upper navigation button while the BIOS setup screen is open causes
the cursor in the BIOS setup screen to move up. This is the same as if you had tapped Arrow Up
on a keyboard. This feature is also functional in the operating system boot menu.
Pressing the bottom half of the upper navigation button while the BIOS setup screen is open
causes the cursor in the BIOS setup screen to move down. This is the same as if you had tapped
Arrow Down on a keyboard. This feature is also functional in the operating system boot menu.
Pressing the top half of the lower navigation button while the BIOS setup screen is open causes
the cursor in the BIOS setup screen to move right. This is the same as if you had tapped Arrow
Right on a keyboard.
Pressing the bottom half of the lower navigation button while the BIOS setup screen is open
causes the cursor in the BIOS setup screen to move left. This is the same as if you had tapped
Arrow Left on a keyboard.
Table 1-4. Tertiary Functions of Application and Navigation Buttons
12
Osian_UG.book Page 13 Monday, October 9, 2006 1:24 PM
Getting Started
SECURITY FUNCTIONS OF APPLICATION BUTTONS
Five buttons are used when implementing security functions. Four of the buttons are used to enter the password, and
the fifth is used as an Enter button. Instructions for using the security feature follow the table.
Button Icons
Security Icons
Security Purpose
Security Enter Button
Ctl-Alt-Del Button
1
Security Button 1
2
Security Button 2
3
Security Button 3
4
Security Button 4
EMail Button
Orientation Button
Escape Button
Enter Button
Table 1-5. Security Functions of Application Buttons
SETTING UP THE SECURITY PANEL
When you receive your Tablet PC, the security panel
application is pre-installed without any passwords. The
following sections provide detailed information on your
security panel, how to set, change or remove passwords.
Numbered Buttons
Use these buttons to enter your password.(Figure 1-5)
The following are examples of valid button strokes:
■
■
■
■
Pushing [4] by itself
Pushing [2] and [3] at the same time
Pushing [1], [2], and [4] at the same time
Pushing [1], [2], [3], and [4] at the same time
The following are valid passwords. The numbers within
braces ({ }) are button strokes using more than one
button.
{[2]+[3]}, [1], [Enter]
[4], [enter]
{[1]+[3]}, {[2]+[3]+[4]}, [1], [4], [2], [Enter]
Enter Button
After entering the button strokes, push this button to
enter the password into the Tablet PC. (Figure 1-5)
■
PASSWORDS
Setting Passwords
When shipped from the factory, no passwords are set.
You have a choice of having no password or setting a
supervisor and user password. You must set the supervisor password before the user password.
The user and supervisor password may be set on this
Tablet PC. A supervisor password is typically the same for
all Tablet PC’s and notebooks in a work group, office, or
company to allow for system management. Individual
computers in a group environment should not use a
common password. A password consists of one to five
button strokes plus the enter button. A valid stroke
consists of pushing one or up to four buttons simultaneously.
■
■
■
■
The purpose of supervisor password is to
be able to bypass the user password in
case the user password is forgotten. The
supervisor password alone will not lock
the system.
You must set the supervisor and user
passwords for the security panel to work.
13
Osian_UG.book Page 14 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section One
Setting Supervisor Password
You must have set a supervisor password before setting
any user passwords. The supervisor password can bypass
the user password.
1. Go to the Start menu.
2. Click on Run.
3. Type in:
C:\Program Files\Fujitsu\Security
Panel Application\Supervisor\
FJSECS.EXE, then press [Enter]
4. Follow the on-screen instructions to set the
Supervisor password.
Setting User Password
1 Go to the Start menu.
2. Click on All Programs.
3. Click on Security Panel Application -> Security
Panel Application.
4. Follow the on-screen instructions to set the
user password.
You may change or remove the supervisor
or user password by repeating the steps
defined above.
is entered or an invalid password is entered while the
system beeps, the system will return to its previous
locked state (standby or off) and the Security Indicator
will go off. To reactivate the Tablet PC after a password
failure, you must press the Suspend/Resume button,
then enter a correct password.
Remember the user password you specified
on the Security Panel Application. If you
forget the password you will not be able to
use your computer. The supervisor password can override the user password.
PRECAUTIONS
Low Battery Operations
If your Tablet PC has a low battery, pushing the suspend/
resume button does not unlock the Tablet PC. To resume
normal operation, first attach a power supply to the
system. Then you may unlock the Tablet PC.
UNINSTALLING THE SECURITY
PANEL APPLICATION
You have two options when uninstalling the security
panel application:
■
USING YOUR SECURITY PANEL
The security lock feature is in effect both when the system
resumes from Off, Standby, or Hibernation state. You
always need to push the Security Panel buttons to input
the user password. Your system will not begin the boot
sequence until you enter your supervisor/user password.
From Off State
1. Turn on your system.
2. When the Security Indicator flashes, enter the password and press Enter button.
For example, if the password is 22222, first press
Button 2 five times and press the Enter button. The
Tablet PC will boot to normal operation.
From Standby/Hibernation State
1. Press your Suspend/Resume button.
2. When the Security Indicator flashes, enter the password and press Enter button.
The Tablet PC should resume normal operation.
Incorrect Password Entry
If an invalid supervisor or user password is entered three
times in succession, the system will “beep” for about one
minute. If a valid password is entered within a minute
(while system beeps), the beeping will stop and the
Tablet PC will resume normal operation. If no password
14
■
Remove passwords and uninstall the security panel
application software. This will disable all security
features.
Uninstall the security panel application with password
still active. This will not allow any changes to the
password.
Uninstalling the Security Panel
Application Software
Remove passwords when User wants no password
protection whatsoever and doesn’t want to give anybody
the utility to set a password on their computer. In this
case, if passwords (supervisor, user, or both) are set, the
passwords must first be cleared BEFORE removing the
application. To clear passwords, follow same procedure
in SETTING PASSWORD CODES except this time,
select REMOVE, enter current password then click Next.
When asked to confirm select Yes.
Removing Security Panel Application with
Passwords Still Active
Using this feature will not allow any changes to
the password.
Removing the applications does not remove
the password. It simply removes the utility
to change/add/remove passwords. To
change your password you must reinstall
the application.
Osian_UG.book Page 15 Monday, October 9, 2006 1:24 PM
Getting Started
User:
1. Go to Start -> Control Panel.
2. Open Add or Remove Programs Properties in the
Control Panel.
3. Select the Security Panel Application in the list, and
click Change/Remove.
4. When the Confirm File Deletion box appears,
click Yes.
Supervisor:
1. Go to Start -> Control Panel.
2. Open Add or Remove Programs Properties in the
Control Panel.
3. Select the Security Panel Application for
Supervisor in the list, and click Change/Remove.
4. When the Confirm File Deletion box appears,
click Yes.
Reinstalling the Security Panel Application
To reinstall supervisor or user security application, you
will need your Drivers and Applications CD. The
Utilities\Security Panel Application folder contains two
separate folders: Supervisor and User. The setup files for
supervisor and user security applications are contained
in those folders.
1. Go to the Utilities\Security Panel Application\
Supervisor folder on the CD and double-click the
setup.exe file. The Installing Security Panel Application window will appear. Follow the instructions on
the screen.
2. Go to the Utilities\Security Panel Application\User
folder on the CD and double-click the setup.exe file.
The Installing Security Panel Application window
will appear. Follow the instructions on the screen.
Supervisor and user passwords can be set via Windows
software using the FJSECS.exe and FJSECU.exe files,
respectively. FJSECU.exe for the user password cannot
run without first setting a supervisor password. You need
to run FJSECS.exe first to set the supervisor password.
Follow instructions under Setting Passwords on page 13.
If you forget both passwords, please contact Fujitsu
Computer Systems Corporation Service and Support at
1-800-8Fujitsu (1-800-838-5487). Fujitsu Computer
Systems Corporation charges a service fee for unlocking a
password-restricted Tablet PC. When calling please have
a valid credit card and provide proof of ownership. You
will then be given instructions on where to ship your
Tablet PC.
15
Osian_UG.book Page 16 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section One
CONNECTORS AND PERIPHERAL INTERFACES
Connectors and peripheral interfaces on the Stylistic
ST5100 Series Tablet PC allow the connection of a
variety of devices. Specific locations are illustrated in
Figures 1-2 through 1-5.
Connector/
Peripheral
Table 1-6 provides a description of each peripheral
connector on the Stylistic ST5100 Series Tablet PC. Each
of the illustrated icons is either molded into or printed
on the Tablet PC chassis.
Tablet PC
Icon
Purpose
DC input
connector
Connect an external power source such as the AC adapter or auto/airline
adapter.
USB Port
Connect Universal Serial Bus 2.0 compliant devices to the Tablet PC.
PCMCIA
Card slot
Insert a Type I or Type II PC Card.
SD Card/
Memory Stick
slot
Insert a Secure Digital (SD) Card or a Memory Stick.
Microphone jack
Connect an external microphone. The internal microphone is disabled when you
plug in an external microphone.
Headphone jack
Connect stereo headphones or powered external speakers. The internal speaker
is disabled when you plug in external headphones or powered speakers.
IrDA/FIR port
An infrared transceiver built into the Tablet PC allows you to communicate with
other devices that are compliant with the IrDA Standard Rev. 1.1. Effective range
for infrared communication is about 3 feet, and within 15 degrees off center. A
clear line-of-sight path must exist between the IrDA port on the Tablet PC and
the IrDA transceiver on the other device.
Modem
Connect a telephone line to the optional internal modem using a standard RJ-11
telephone plug.
Tablet Dock port
Connect the Stylistic ST5100 Series Tablet Dock or other approved docking
device. Refer to documentation accompanying the docking device for more
information.
Infrared
keyboard/
mouse port
An infrared receiver built into the Tablet PC allows you to communicate with a
Fujitsu wireless infrared keyboard or mouse. The keyboard infrared port works
optimally when it is placed between 10 to 30 cm (approximately 4 in. to 12 in.)
from the keyboard infrared port (which is located on the bottom edge of the
Tablet PC). Ensure there is a clear line-of-sight path between the infrared receiver
on the Tablet PC and the infrared transmitter on the keyboard or mouse. Note
that an infrared keyboard or mouse works best when the system is in landscape
orientation.
16
Osian_UG.book Page 17 Monday, October 9, 2006 1:24 PM
Getting Started
Connector/
Peripheral
Tablet PC
Icon
Purpose
Lock slot
The security slot allows you to secure the Tablet PC using compatible locking
devices.
IEEE 1394 jack
The IEEE 1394 jack allows you to connect IEEE 1394 (Firewire) devices such as
digital video cameras and external hard drives to your Tablet PC.
Suspend/Resume
button
The Suspend/Resume/Power On button allows you to suspend Tablet PC
activity without powering off, resume your Tablet PC from standby mode, and
power on the system when it has been shut down from Windows.
Page Up/
Page Down
The Page Up/Page Down button allows you to navigate quickly from page to
page without scrolling.
Local Area
Network (LAN)
The LAN (RJ-45) jack is used to connect the internal 10/100/1000* Base-T/Tx
Ethernet to a Local Area Network (LAN) in your office or home, or broadband
devices such as a cable modem, DSL, or satellite internet.
*1000 Mbps, commonly referred to as Gigabit Ethernet.
Battery Release
Latch
The battery release latch allows you to remove the battery from your system for
storage or replacement.
Wireless LAN/
Bluetooth
On-Off Switch
The wireless LAN/Bluetooth switch allows you to turn power to the optional
wireless LAN or Bluetooth devices on and off.
Fingerprint Swipe
Sensor
The optional fingerprint swipe sensor allows you to avoid having to enter a user
name and password every time you want to log into the system. This icon
indicates the direction in which you should swipe your finger.
Table 1-6. Peripheral Connectors/Interfaces
17
Osian_UG.book Page 18 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section One
18
Osian_UG.book Page 19 Monday, October 9, 2006 1:24 PM
2
Using Your
Stylistic Tablet PC
19
Osian_UG.book Page 20 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section Two
20
Osian_UG.book Page 21 Monday, October 9, 2006 1:24 PM
U s i n g Yo u r S t y l i s t i c S T 5 1 0 0
Using the Stylistic ST5100 Series Tablet PC
This chapter covers the fundamental concepts, basic
system operation and use, and system functions of the
Stylistic ST5100 Series Tablet PC. You should familiarize
yourself with this information before you attempt to
operate the system.
Prior to using your system, be sure to fully
charge the battery if you plan to run on
battery power. Failure to do so may result
in erratic performance.
SYSTEM STATES
Before you begin using your Tablet PC, review the
different system states (or modes) that the system can
use. Being familiar with these states will help you determine whether it is appropriate to turn on, resume,
standby, hibernate or shut down the system when you
begin or end a session. System behavior for each system
state is described briefly in the following, with each
system state listed in decreasing order of power usage:
• On state: The system is running and the display
screen is on.
• Idle state: Some system functions are regulated or
turned off to conserve power. The display screen may
be turned off. The system returns to the On state
when pen activity or other input is detected.
• Standby mode (S3): System operation is suspended.
Most system functions are turned off to conserve
Icon Appearance
Power icon
displayed
continuously
Power icon blinking
Current State
On State or
Idle State
power. Power to memory is on, maintaining data in
programs that were running before system operation
was suspended. The system does not respond to the
pen or other input when in Standby mode. Refer to
the “Resuming System Operation” section later in this
chapter for information on returning the system to
the On state.
• Hibernate mode (S4): System operation is
suspended. All system functions are turned off to
conserve power. Active data in programs that were
running before suspending system operation is stored
on the hard disk drive. The system does not respond
to the pen or other input. Refer to the “Resuming
System Operation” section later in this chapter for
information on returning the system to the On state.
• Off state: All system functions are turned off to
conserve power. The system does not respond to the
pen or other input. The system boots at the next
system power-on.
The system consumes the same amount of
power whether it is in Hibernate mode or
the Off state.
Your system may be configured to enter some of these
states automatically after a period of inactivity to
conserve battery power.
To Change State*
To enter Off state, shut down the system using the Start menu on your system.
To enter Standby or Hibernate† state, suspend system operation using either a
hardware or software suspend.
Standby†
To enter the On state, resume system operation by pressing the Suspend/
Resume button.
To enter the Off state, resume system by pressing the Suspend/Resume
button, then shut down your system.
Power icon not
displayed
Off State, or,
Hibernate
To enter the On state, start your system, or resume system operation by
pressing the Suspend/Resume button.
Table 2-1 Changing System States
* Information in Table 2-1 is supplied to help you understand which system states your system can enter from the current
system state. Refer to the procedures on starting the system, shutting down the system, suspending system operation, and
resuming system operation given later in this chapter.
†
Your system may be configured to use either Standby mode or Hibernate mode.
21
Osian_UG.book Page 22 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section Two
When you use your Tablet PC, you can change the
current system state in a number of ways, depending on
the system’s current state. To determine the current
system state, observe the Power icon in the Status
display. Table 2-1 on page 21 gives the different system
states represented by the Power icon and describes how
you can change the system state from the current state.
POWERING UP THE TABLET PC
To suspend system operation:
1. Press the Suspend/Resume button, or carry out the
Standby command from your operating system or
power management program. (If your system is
configured to suspend operation using Hibernate
mode, which is explained later in this procedure, a
message is displayed while data is saved to your hard
disk.)
Follow the procedure below to start your Tablet PC.
Before you begin, confirm that the system is in the Off
state. To do so, observe the Status display. If the Power
icon is not visible in the Status display, the system is in
Off state or in Hibernate mode and it is safe to perform
this procedure. If the Power icon is visible (either
blinking or on continuously), do not perform this
procedure. See “System States” earlier in this chapter for
details on modes represented by the Power icon.
1. Ensure that the battery in your Tablet PC is
sufficiently charged, or connect an external power
source such as the AC adapter or auto adapter to
your Tablet PC.
2. Press the Power On/Suspend/Resume button to start
the system.
After performing initialization, the system starts the
operating system installed on the hard disk drive. Once
the operating system is running, you can use the system.
SHUTTING DOWN THE SYSTEM
Follow these steps to shut down/turn off your system:
1. If system operation has been suspended, resume
system operation. See “Resuming System Operation” later in this chapter for details.
2. Save your work and close all running programs.
3. Choose Shut Down from the Windows Start menu.
4. Carry out the Shut Down command.
The system is now in the Off state.
SUSPENDING SYSTEM OPERATION
The Tablet PC allows you to suspend the system operation without closing programs or exiting the operating
system. Use this feature to conserve battery power when
a system shutdown is not practical or when the battery
needs to be changed.
If you have set your system to turn power
off from the Power Options utility in the
Control Panel, the following procedure will
not be possible, since pressing the button
shuts the system down rather than
suspending it. To change your power
options, go to Start -> Settings -> Control
Panel -> Power Options.
22
If you are replacing the battery, wait until
system operation is suspended and the
power icon is flashing before you remove
the battery. Failure to do so could result in
loss of your unsaved data. (Note that if the
Resume On LAN function is enabled in the
BIOS setup, you should not remove the
battery unless the system is shut down.
When Resume ON LAN is enabled, the
bridge battery is disabled in order to
optimize battery life.)
2. The Power icon either flashes (Standby) or is not
displayed (Hibernate) when system operation is
suspended, depending on how your system is
configured. At this point, programs that were
running are stopped, active data is saved, and the
system enters one of two different low-power states,
or standby modes, as explained in the following
paragraphs.
3. Observe the Power icon in the Status display to
determine which suspend mode your system is
using.
■
Power icon is blinking: Standby mode.
In this mode, active data is saved by maintaining
power to RAM while most other system components
are powered off. The Battery Gauge icon in the Status
display indicates the battery charge level.
■
Power icon is not displayed: Hibernate mode.
In this mode, active data is stored on the hard disk
drive and power usage is reduced to the same level
used in the Off state. When the system is in Hibernate
mode, the Battery Gauge icon is not visible in the
Status display. In this mode, there is no danger of
losing data if battery power is lost.
If you have successfully performed this procedure,
system operation is now suspended. Refer to
“Resuming System Operation” later in this chapter to
resume system operation. Also, note the following
with regard to suspending system operation:
Osian_UG.book Page 23 Monday, October 9, 2006 1:24 PM
U s i n g Yo u r S t y l i s t i c S T 5 1 0 0
■
You can remove the battery while the system is in
Standby or Hibernate modes in order to install a
charged battery. To prevent losing unsaved data, wait
until system operation has suspended before you
remove the battery. Note that after you remove the
battery, you have approximately five minutes to replace
it with a new battery or to plug in a power supply
before the bridge battery is depleted.
■
Your system may be configured to suspend operation
automatically after a period of inactivity.
■
Your system may be configured to enter Hibernate
mode automatically after a period of time in Standby
mode.
■
The system uses a small amount of battery power when
in Standby mode. Eventually, the battery will become
fully discharged.
RESUMING SYSTEM OPERATION
To resume operation from either Standby or Hibernate
modes, press the Suspend/Resume button.
■
From Standby mode
Status lights indicate that the system state is changing.
It may take up to a minute before the system returns to
the On state and system operation resumes. Note that
the display turns on shortly before the pen becomes
active due to the power-up sequences observed by the
system.
■
From Hibernate mode
Active data is read from the hard disk drive, and the
system returns to the On state after a short time.
Note that power to several system
components must be restored before
system operation resumes. Allow sufficient
time for system operation to resume
before attempting to use the system. If
your system uses Hibernate mode, it will
take longer to resume operation as
compared to using Standby mode. Time is
needed to read data from the hard disk
drive.
If you will not be using the system for an
extended period, shut down the system
rather than using Standby mode.
■
■
If the battery charge drops to a Low-Battery Warning
level while the system is running, the system will beep
periodically. If this occurs, suspend system operation,
shut down the system, or attach an external power
source, such as the AC adapter, to the Tablet PC.
If the battery charge drops to a Critically Low level
while the system is running, the system is forced into a
Standby or Hibernate mode. If this occurs, you must
either install a charged battery, or connect an external
power source such as the AC adapter before you can
resume system operation. (If the charge drops to a Critically Low level while the system is in Standby mode,
the system stays in that mode until power is restored or
totally dissipated.)
■
Suspending system operation interrupts data communications; therefore, some programs may block the
system from suspending to prevent an interruption.
■
The suspend action of the Suspend/Resume button
may be disabled to prevent accidental interruption. If
this is the case, pressing the Suspend/Resume button
will not suspend system operation as described here.
(In this case, standby mode can only be achieved using
the system software). Contact your local help desk or
reseller if your system configuration is not suitable.
■
If your system is equipped with a PC Card that allows
you to connect to a wired or wireless network, you may
be logged off the network after a period of inactivity
while system operation is suspended. Contact your
network administrator or help desk, or call Fujitsu
Service and Support at 1-800-8Fujitsu (1-800-8385487) for details on your network log-off parameters.
Use the system as you normally would once system operation resumes.
All programs resume at the point where execution
stopped when system operation was suspended.
USING THE SHOCK SENSOR UTILITY
The Shock Sensor Utility is a feature that helps to The
Shock Sensor Utility is designed to decrease the risk of
damage to the computer's hard disk drive (HDD) in the
event of excessive impact or vibration. The Shock Sensor
Utility also has the ability to improve the security of the
computer by automatically locking the computer with a
password when it is carried. Note that the HDD protection and computer locking features are mutually exclusive; both cannot be selected at the same time.
■
Shock Sensor Utility does not completely
protect the HDD and does not provide
absolute security for the computer.
■
The computer may stop temporarily while
the HDD head is retracted. To restart the
computer, keep the system horizontal.
1. Double-click the Shock Sensor Utility icon in the
Notification Area at the bottom-right of the screen.
The [Shock Sensor Utility] window appears.
2. Click the [Setting] button. The [Shock Sensor Utility
Settings] window appears.
Action
Select the action you wish this utility to perform:
23
Osian_UG.book Page 24 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section Two
■
■
■
Protect HDD from impact. HDD head is retracted
when an impact to the computer is detected.
Lock computer when carried. Lock the computer
when it is being carried.
Nothing. No action.
Sensitivity of impact/horizontal move/fall/carry
detection
Adjust the sensitivity of the acceleration sensor based on
system motion or impact.
■
■
■
Go up. Use [A] key.
Go down. Use [Z] key.
Close. Use [Esc] key.
ADJUSTING THE DISPLAY BRIGHTNESS
There are four ways to adjust your display’s brightness:
Depending upon whether you are running
your system on battery or AC power, the
default screen brightness settings will be
different. The screen brightness default for
running on battery is lower than that on
AC power in order to optimize battery life.
Ignore periodic vibration.
If vibration is periodic, disregard it.
Ignore mouse click
When the mouse is clicked, sensitivity is temporarily
lowered.
■
Click the Tablet icon in the system tray at the bottom
right of the screen. (When the cursor is on top of the
icon, a message stating “Change tablet and pen settings” is displayed.) When the Tablet and Pen Settings
window appears, select the Display tab, and move the
Screen Brightness slider to change the brightness.
■
Click Start -> Control Panel -> Tablet and Pen Settings. Select the Display tab, and move the Screen
Brightness slider to change the brightness.
■
Click the Fujitsu Menu icon in the system tray at the
bottom right of the screen. (When the cursor is on top
of the icon, a message stating “Fujitsu Menu...” is displayed.) Select Tablet and Pen Settings and select the
Display tab. Move the Screen Brightness slider to
change the brightness.
■
Press the Fn key twice to invoke the Fujitsu menu and
select Tablet and Pen Settings.
Ignore keyboard action
When the keyboard is used, sensitivity is temporarily
lowered.
Confirm calibration when user logs on
Select [Confirm calibration when user logs on] if you
want to recognize the current orientation as horizontal
at logon.
Perform calibration automatically when user logs
on
Select [Perform calibration automatically when user logs
on] if the system is normally used on a horizontal
surface.
[Calibrate Now]
The calibration is executed. Please position the
computer as horizontally as possible, then click the
[Calibrate Now] button. The current horizontal position
will be recognized as the true horizontal by performing
the calibration.
3. Click the [OK] or [Cancel] button. The [Setup]
window closes.
Using the Shock Sensor Monitor Window
Right-click the Shock Sensor Utility icon in the Notification Area at the bottom-right of the screen, and select
[Monitor] from the menu. The Monitor window
appears.
USING THE PEN
You can use the Stylistic ST5100 Series pen to generate
and create electronic “ink”, to select items, and to navigate through programs on the Tablet PC. Programs that
support handwriting recognition also allow you to write
characters directly on the screen with the pen. You can
also use the pen as a drawing tool.
Barrel Switch
Eraser Switches
Note that the Monitor is designed for entertainment,
and has no effect on system settings or orientation. To
navigate the monitor, use the buttons described below.
■
■
■
■
Advance. Incline the display to the hinge side, or use
[Up] key.
Back. Incline the display to the mouse-button side, or
use [Down] key.
Right. Incline the display to the right side, or use
[Right] key.
Left. Incline the display to the left side, or use [Left]
key.
24
Tip Switch
Pen Tether Attachment Point
Figure 2-1. Stylistic ST5100 Series Pen
Osian_UG.book Page 25 Monday, October 9, 2006 1:24 PM
U s i n g Yo u r S t y l i s t i c S T 5 1 0 0
The Stylistic ST5100 pen is a sophisticated,
high-quality electronic instrument that can
be damaged if used improperly. Treat the
pen as you would any precision device.
The following list contains guidelines for
proper pen handling:
• Do not gesture with the pen, use it as a
pointer, or tap it on surfaces other than
the Tablet PC screen.
• Do not try to turn the thumb grip on
the pen; it is designed for inserting and
removing the pen from the pen holder
and for attaching a pen tether.
• Never store the pen with the tip bearing
the weight of the pen (e.g., sitting tip
down in a pencil cup). Storing the pen
tip down could distort the internal
mechanism over a period of time
(especially in higher temperatures),
causing the tip to act as if it is always
depressed. To avoid damage, the pen
should be stored in the pen holder
when not in use.
The screen reacts when the pen tip is approximately 1/8
inch (3-5 mm) from the screen. The pen has four
switches: a tip switch, a barrel button toggle switch with
switches at both ends, and an "eraser" switch, located on
the end of the barrel. By default, the tip switch corresponds to the left mouse button, and the front toggle
(closest to the pen tip) barrel button switch corresponds
to the right mouse button (when used in combination
with the tip switch). The rear toggle of the barrel button
switch and the eraser switch at the end of the barrel act as
electronic ink “erasers”.
The rear toggle, eraser, and tip click pressures can be
changed by clicking [Start] -> Control Panel, and
double-clicking the Fujitsu Pen Settings icon. Note that
the rear toggle switch and the eraser switch are both
affected by the same settings; they cannot be changed
individually.
To change the rear toggle and eraser button function,
select the drop-down list to select a new function, then
click [Apply]. If you don’t want the rear toggle and
button switch to have any function, select Ignore from
the list.
Adjusting the click pressure determines how much pressure must be put on the pen tip in order for the screen to
react. The softer it is set, less pressure is required; the
harder it is set, more pressure is required. To change the
click pressure, use the slider bar to make the click pressure harder or softer, then click [Apply].
• Ensure that a screen protector is installed
on the Tablet PC screen before you use
the pen. The warranty does not cover a
scratched screen.
• Use only the pen provided with your
Tablet PC. Do not use substitutes that
were not designed for the Stylistic
ST5100 Series Tablet PC.
Here are some hints that may help you use the pen more
effectively:
• To activate the tip switch, tap or hold the pen tip
against the screen.
• To activate the barrel button switch, press and hold
the end of the button you wish to use (front toggle is
the right mouse button switch; the rear toggle acts as
an electronic “eraser”).
• To move the cursor, hold the pen tip within 1/8 inch
(3 - 5mm) from the screen and move the pen.
• To start a program, double-tap the pen tip (tap the
pen tip twice rapidly) on the program icon as you
would double-click a mouse.
• To select an object, tap the pen tip on the object once.
• To “double-click” an object, tap twice on the object
quickly.
• To move, or “drag”, an object on the screen, place the
pen tip directly over the object, then as you hold the
pen tip against the screen, move the pen.
CALIBRATING THE PEN
For information about calibrating your pen, refer to the
literature that came with the operating system.
INSTALLING A PEN TETHER
To prevent dropping or losing your pen, you should
attach it to your system using the pen tether that is
included with the system.
To attach the pen tether to your Tablet PC, perform the
following steps:
1. Attach the end of the pen tether with the smaller loop
to your pen. Do do so, push the end of the tether
through the hole in the pen, then thread the opposite
end of the tether through the loop. (See Figure 2-2.)
25
Osian_UG.book Page 26 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section Two
To charge the battery:
Pen tether
attachment
point
1. Connect a DC power source, such as the AC adapter,
to the DC input connector on the Tablet PC. The
DC Input icon appears in the Status display. If the
battery charge is below 90%, the battery begins
charging and the Charging icon appears in the
Status display. If the battery charge is 90% or higher
when you connect DC power, the battery will not
charge, preventing battery overcharging.
Larger loop
2. Look at the Battery Charge icon in the Status display
to determine the percent of charge in the battery. See
“Status Display” in Chapter 1 of this manual for a
description of the Battery Charge icon.
Smaller loop
Figure 2-2. Installing a Pen Tether
2. Attach the end of the pen tether with the larger loop
to the attachment point on your pen tablet. To do so,
insert the end of the pen tether through the attachment point, then feed the pen through the large loop
in the tether.
REPLACING THE PEN TIP
With use, the pen tip may become worn or may pick up
foreign particles that can scratch the screen. A damaged
or worn tip may not move freely, causing unpredictable
results when using the pen. If your pen exhibits these
problems, you should replace the pen tip. To do so, use
the pen tip removal tool included with your pen.
As long as DC power remains connected to the Tablet PC,
the charging process continues until the battery charge
reaches 100%.
Also note the following with respect to charging the
battery:
• You can use the system, suspend system operation, or
shut down and turn off the system without
interrupting the charging process; however, using the
system while the battery is charging will cause the
battery to charge at a slower rate.
• As noted in the procedure above, the system will not
begin charging the battery if the battery charge level
is 90% or higher when the system is initially
connected to external DC power. (This prevents the
battery from being overcharged.)
Gap
• The battery uses Lithium ion battery cells which have
no “memory effect.” You do not need to discharge
the battery before you begin charging.
Figure 2-3. Tip Removal Tool
REMOVING AND INSTALLING THE BATTERY
To remove the tip, position the tip in the gap between
the two ends of the tool. Pinch the tool together so the
tip is firmly clasped, then pull it from the barrel. If the
tip is worn or damaged, discard it.
The battery can be removed from the Tablet PC and
swapped with a charged battery. The battery can then be
charged in an external charger if one is available. To
remove the battery from the Tablet PC:
To replace the tip, retrieve one of the new tips that
accompanied your pen. Insert the flat end of the tip into
the barrel and push it in firmly until it is seated.
1. Choose one of the following:
If you need more tips, they can be ordered from the
Fujitsu website at: us.fujitsu.com/computers.
CHARGING THE BATTERY
The Stylistic ST5100 Series battery can be charged while
it is installed in the Tablet PC.
• If a charged battery is available, you can suspend
system operation. A built-in “bridge” battery will
maintain the system in Standby mode for about 5
minutes while the battery is removed; this allows
time for replacement with a charged battery.
• If a charged battery is not available, save your work
and close all running programs, then shut down
the system or Hibernate.
• Plug in an external DC power source.
2. Slide the battery release latch in the direction
indicated. (See Figure 2-4 on page 27 for location).
26
Osian_UG.book Page 27 Monday, October 9, 2006 1:24 PM
U s i n g Yo u r S t y l i s t i c S T 5 1 0 0
3. Pull the battery away from the system, as shown in
the illustration and remove the battery from the
Tablet PC.
If you are using an external battery charger, refer to the
instructions provided with the battery charger.
Under Federal, state, or local law, it may
be illegal to dispose of batteries by putting
them in the trash. Be sure to dispose of
batteries in accordance with local
government regulations.
To install the battery:
• Reduce the brightness of the LCD.
• Battery life is dependent upon the operating system,
power settings, and applications in use.
Operation of the Bridge Battery
When installed in the Tablet PC, the battery provides
power to some system components—even when the
system is in the Off state. When the battery is removed,
power is supplied to these components by a “bridge”
battery that is built into the Tablet PC.
The bridge battery is not designed for long-term operation. To maintain the bridge battery properly, observe the
following measures:
1. Orient the battery with the slides in the empty battery
tray. Slide the battery into the tray and press it firmly
until it is seated. When it is properly seated, the
battery release latch should return to position and
lock the battery.
• The bridge battery function is disabled if
Wake On LAN is enabled in the BIOS.
• The system arrives with the bridge
battery in a discharged state. Be sure to
charge it sufficiently before relying upon
it to support the system in the event of
battery removal.
Battery Pack
• To prevent draining the bridge battery, always store
the system with a charged battery installed.
• If the bridge battery becomes drained, it takes
approximately 8 hours for it to be fully recharged.
•
Battery Release Latch
Figure 2-4. Removing the Battery
Once the battery is installed, you can resume system
operation or start and use your system normally.
TIPS FOR CONSERVING BATTERY POWER
You can extend the charge life of your battery by
conserving battery power. (Your results may vary
depending on your application and how the system is
configured.) Here are some suggestions to help you
conserve battery power:
• Use an external power source such as the AC adapter
whenever the system is docked.
• Suspend system operation if you know that you won’t
be using the system for a while.
• Shut down the system if you won’t be using the system
for an extended period of time.
• Switch the wireless LAN switch Off when wireless
LAN functionality in not needed (applicable only for
systems with optional wireless LAN).
The bridge battery charges when the AC Adapter is
connected and the system is in On or Off states or
Standby mode. It charges from the battery only when
the system is in the On state.
MODEM CONNECTION
The internal 56 Kbps LAN/modem module
installed in the Stylistic ST5100 Series
Tablet PC has actual maximum transfer
rates of 53 Kbps (receive), 33.6 Kbps
(send), and 14.4 Kbps (fax). Download
rates are limited to 53 Kbps in the United
States due to FCC restrictions.
The Stylistic ST5100 Series Tablet PC is designed to
accept a standard RJ-11 telephone plug. Connect the plug
to the modem jack located on the left-hand side of the
Tablet PC (See Figure 1-5 on page 5 for location). The telephone plug can be inserted whether or not the Tablet PC
has power applied.
If you need assistance configuring the Stylistic ST5100
Series Tablet PC modem or LAN, contact your local help
desk or reseller.
• Use power management (available from the Power
Options in the Control Panel) to help you conserve
power automatically.
27
Osian_UG.book Page 28 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section Two
MEMORY STICK/SD CARD SLOT
Your Tablet PC supports Memory Stick and SD flash
memory cards on which you can store and transfer data
to and from a variety of digital devices. These cards use
flash memory architecture, which means they don’t need
a power source to retain data.
Note that MagicGate functions are not
supported by this slot.
Memory Stick is a flash memory technology developed
by Sony Electronics. Memory Stick allows you to record,
transfer and share digital content, such as digital
pictures, movies, music, voice, and computer data and
applications.
Secure Digital (SD) Cards are very similar to Memory
Sticks, but they are shorter. Like the Memory Stick, SD
Cards allow portable storage among a variety of devices,
such as cell phones, GPS systems, digital cameras, and
PDAs. SD Cards transfer data quickly, with low battery
consumption. Like the memory stick, it uses flash
memory architecture.
2. Make sure there is no card currently in the slot. If
there is, see Removing a Memory Stick/SD Card.
3. Insert your card into the slot with the product label
facing up.
4. Push the card firmly into the slot until it is seated in
the connector.
Removing A Memory Stick/SD Card
To remove a Memory Stick/SD Card, follow these steps:
See your Memory Stick or SD Card manual
for specific instructions on the removal of
your card. Some cards may require your
computer to be in Standby Mode or Off
while removing them.
Push the Memory Stick or SD Card in until it unlatches.
It will then eject from the slot for removal
PC CARD SLOT
The Stylistic ST5100 Series Tablet PC Card slot allows
you to insert a Type I or Type II PCMCIA Card.
Inserting a PC Card
To insert a PC card, position the side with the arrow
facing up (i.e., when looking at the tablet’s display side,
the arrow on the card should be visible.) Slide the card
into the PC Card slot, and press it firmly to ensure
proper seating. (See Figure 2-6 for location)
If you need assistance inserting a PC Card in the Stylistic
ST5100 Series Tablet PC, contact your corporate help
desk or reseller.
Figure 2-5. Memory Stick and Secure Digital Card
Inserting Memory Stick/SD Cards
Memory Sticks and SD Cards are inserted in the
Memory Stick/SD Card slot (Figure 1-4). To insert a
Memory Stick or SD Card, follow these steps:
■
■
Inserting or removing a Memory Stick
or SD Card during your system’s shutdown or bootup process may damage
the card and/or your computer.
Do not insert a card into a slot if there is
water or any other substance on the card
as you may permanently damage the
card, your Tablet PC, or both.
1. See your Memory Stick or SD Card manual for
instructions on the insertion of your card. Some
cards may require that your system is off while
inserting them.
28
Figure 2-6. Inserting a PC Card
Removing a PC Card
To remove a PC Card, first click the Safely Remove
Hardware icon in the system tray in the bottom righthand corner of the display. Select PC Card from the list,
and click [Stop].
Press the PC Card eject button so that it pops out. Once
the button has popped out, press it firmly to eject the
card. (See Figure 2-7 for location)
Osian_UG.book Page 29 Monday, October 9, 2006 1:24 PM
U s i n g Yo u r S t y l i s t i c S T 5 1 0 0
2. Remove the two screws from the cover plate on the
back of the Tablet PC and remove the cover plate as
shown in Figure 2-8.
PC Card Eject Button
Figure 2-7. Removing a PC Card
REMOVING AND INSTALLING MEMORY
There are two DIMM slots in your Tablet PC. 256 MB,
512 MB, 1 GB, and 2 GB modules are available, so you
can install a combination of up to 4 GB in the system.
■
Do not remove any screws from the
memory upgrade module compartment
except the ones specifically shown in the
directions for installing and removing the
memory upgrade module.
■
The memory upgrade module can be
severely damaged by electrostatic discharge (ESD). To minimize risk to the
module, observe the following precautions:
■
■
■
Before handling a memory module,
touch a grounded metal object to
discharge static electricity built up in
your body.
When installing or removing a
memory module, hold it by the edge
so as not to touch any contacts or
chips. Be careful not to touch any
internal computer terminals or
components; the oil from your fingers
could cause a short to the components.
Be sure to power down your system
before adding or removing memory
modules. Even if the system is in
hibernate or standby states, data
could be lost or the memory could be
damaged if power is still available to
the system.
Installing a Memory Module
To install a DIMM module in the Tablet PC:
1. Ensure that the Tablet PC is off. To do so, carry out
the Shut Down command in the Start menu. (Do not
attempt to remove or install a DIMM module when
the system is in Standby mode or running.)
Figure 2-8. Accessing the Memory Slot
3. Insert the DIMM module in the socket at an angle
and push it down until it locks into place as shown in
Figure 2-9. Note that the DIMM module is keyed to
prevent it from being inserted backwards.
Figure 2-9. Installing a DIMM Module
4. Reinstall the cover and screws that you removed in
step 2.
5. Confirm that the DIMM module is recognized by the
system. To do so, run BIOS Setup. The size of the
DIMM module should be displayed in the Info menu
in BIOS Setup.
The DIMM module is installed in the Tablet PC and you
can now use the system.
Removing a Memory Module
To remove a DIMM module:
1. Ensure that the Tablet PC is off. To do so, carry out
the Shut Down command in the Start menu. (Do not
attempt to remove or install a DIMM module when
the system is in Standby mode or running.)
29
Osian_UG.book Page 30 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section Two
2. Remove the screws from the cover plate on the back
of the Tablet PC and remove the cover plate as
shown in Figure 2-8.
3. Spread the fingers on the socket that lock the DIMM
module in place until the DIMM module is loose.
Figure 2-10. Removing a DIMM Module
4. Remove the DIMM module from the socket.
The DIMM module is now removed from the Tablet PC.
See "Installing a Memory Module" to install a new
DIMM module.
30
Osian_UG.book Page 31 Monday, October 9, 2006 1:24 PM
3
Care and
Maintenance
31
Osian_UG.book Page 32 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section Three
32
Osian_UG.book Page 33 Monday, October 9, 2006 1:24 PM
Care and Maintenance
Care and Maintenance
This chapter gives you pointers on how to care for and
maintain your Stylistic ST5100 Series Tablet PC.
■
■
Do not remove any screws from the
memory upgrade module compartment
except the ones specifically shown in the
directions for installing and removing the
memory upgrade module.
The memory upgrade module can be
severely damaged by electrostatic discharge (ESD). To minimize risk to the
module, observe the following precautions:
■
■
■
■
Before docking or undocking your
system (when using a Tablet Dock), it
is good practice to always touch a
grounded metal object to discharge
static electricity built up in your body.
Before handling a memory module,
touch a grounded metal object to
discharge static electricity built up in
your body.
When installing or removing a
memory module, hold it by the edge
so as not to touch any contacts or
chips. Be careful not to touch any
internal computer terminals or
components; the oil from your
fingers could cause a short to the
components.
Be sure to power down your system
before adding or removing memory
modules. Even if the system is in
hibernate or standby states, data
could be lost or the memory could be
damaged if power is still available to
the system.
CARING FOR YOUR TABLET PC
Please note the following information regarding proper
treatment of your Tablet PC:
■
Your Tablet PC is a durable but sensitive electronic
device. Treat it with respect and care.
■
Make a habit of transporting the system in a suitable
carrying case.
■
Do not attempt to service the computer yourself.
Always follow installation and operation instructions
closely.
■
If you accidentally spill liquid on your Tablet PC:
1. Turn it off.
2. Position it so that the liquid can run out.
3. Let it dry out for 24 hours, or longer if needed.
4. If your Tablet PC will not boot up after it has dried
out, call your support representative.
■
Do not use your Tablet PC in a wet environment (near
a bathtub, swimming pool).
■
Always use the AC adapter and batteries that are
approved for your system.
■
Avoid exposure to sand, dust and other environmental
hazards.
■
Do not expose your Tablet PC to direct sunlight for
long periods of time as excessive temperatures may
damage your system.
■
Do not put heavy or sharp objects on the computer.
■
Do not carry your system in a bag or briefcase while it
is running; doing so could result in overheating or hard
disk drive problems.
■
If you are carrying your system in a briefcase, or any
other carrying case, make sure that there are no objects
in the case pressing on the display.
■
Do not drop your Tablet PC or touch the screen with
any sharp objects.
PROTECTING THE DISPLAY SCREEN
The Stylistic ST5100 Series Tablet PC is designed to
provide you with years of service. Using a screen
protector will help ensure the screen remains as clear as
possible. When installed, the screen protector becomes a
durable, replaceable writing surface that protects the
display screen from abrasion.
To obtain additional screen protectors, use Fujitsu part
number FPCSP08AP (6-pack) when ordering. Additional
information about installation is included with the
screen protectors.
During normal use of the Tablet PC, small
particles from the environment can become
embedded in the pen tip and scratch the
screen. To prevent scratching the screen,
ensure that a screen protector is installed
before using your Tablet PC. The warranty
does not cover a scratched screen.
To install a new screen protector on your Tablet PC:
1. If a screen protector is already installed on the display
screen, remove it before installing the new screen
protector.
The screen protector is held onto the display screen
surface by a thin strip of adhesive around the edges. A
notch in one corner of the screen protector allows
you to slide your fingernail under the screen
protector for easy removal.
33
Osian_UG.book Page 34 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section Three
2. Clean the display by wiping the screen gently using a
soft cotton cloth dampened with isopropyl alcohol.
Ensure that all residue has been removed from the
screen before applying a new screen protector.
Remove the protective coating from the adhesive
side of the screen protector first, as shown in Figure
3-1.
■
The Stylistic ST5100 Series Tablet PC is
not waterproof. Do not pour liquids on
the system or wash it with a heavily
soaked cloth.
■
Do not place items on the top of the display, or damage may occur.
Figure 3-3. Removing the protective cover
5. Remove the protective plastic cover from the face of
the screen protector, as shown in Figure 3-3.
.
6. Clean any residue left behind by the protective
coating from the exposed surface of the screen
protector by wiping gently with a soft cotton cloth
dampened with isopropyl alcohol. Wipe the screen
protector with a soft dry cloth to remove any lowtack adhesive; this will help prevent the pen tip from
squeaking.
STORING THE TABLET PC
Figure 3-1. Removing the Protective Sheet
3. Apply the screen protector to the display screen
surface. When doing so, orient the screen protector
with the adhesive side of the screen protector facing
the display screen and the notched corner of the
screen protector oriented as shown in Figure 3-2.
Store the Stylistic ST5100 Series Tablet PC in the Off
state with a fully charged battery installed. You can store
the Tablet PC in the Off state for about 30 days with a
fully charged battery installed. After this period, the
battery should be recharged or replaced with a charged
battery.
If you intend to store the Tablet PC for a longer period of
time, the small battery that maintains system time may
need to be replaced. Replacement of the clock battery
should only be performed by authorized technicians.
AVOIDING OVERHEATING
Do not expose your Tablet PC to direct
sunlight for extended periods of time. High
temperatures could damage your tablet.
Figure 3-2. Installing the screen protector
4. Apply pressure to the screen protector with your
finger using a continuous wiping motion along the
edges. The adhesive sets completely within 48 hours.
To ensure a good seal between the screen protector
and the display, do not lift the screen protector from
the display once it has been applied.
34
The Tablet PC monitors its internal temperature. As the
internal temperature approaches the tolerable limits of
heat-sensitive components, system functions are automatically limited or turned off to prevent damage.
To protect your notebook from damage and to optimize
performance, keep all air all vents unobstructed, clean,
and clear of debris. This may require periodic cleaning,
depending upon the system environment.
Osian_UG.book Page 35 Monday, October 9, 2006 1:24 PM
Care and Maintenance
Do not operate the notebook in areas where the air vents
can be obstructed, such as in tight enclosures or on soft
surfaces like a bed or cushion.
CLEANING THE DISPLAY SCREEN
To clean the Tablet PC display screen, wipe the screen
surface gently using a soft cotton cloth slightly dampened
with water or isopropyl alcohol.
The Tablet PC is not waterproof. Do not
pour liquids on the Tablet PC or wash it
with a heavily soaked cloth.
TROUBLESHOOTING
Solutions to some common problems are described in
the following sections. If you are experiencing a problem
with your Tablet PC that you cannot solve by taking the
actions described, contact your local help desk or reseller,
or call Fujitsu Service and Support at 1-800-8Fujitsu (1800-838-5487) for further assistance.
System Will Not Resume Operation
If the system will not resume operation after system operation has been suspended, check the following:
• The battery may either be defective, or discharged to a
critically low level. When the battery reaches a
critically low level, the system is forced into Standby
mode to avoid a total system power failure. To correct
this problem, either connect an external power supply
(such as the AC adapter), or install a charged battery
in the Tablet PC.
• The system may be at the critical thermal limit. To
avoid damage to heat-sensitive components, the
system enters standby mode when it gets too hot.
System operation cannot be resumed until the Tablet
PC cools off to a tolerable temperature. Move the
Tablet PC to a cooler location.
Display Screen Blank or Difficult to Read
If the display screen on your Tablet PC appears blank or
is unreadable, confirm that the system is running (the
Power icon is displayed continuously on the Status
display), and check the following:
• The system brightness may be set too low, causing the
screen to appear too dark. To change system
brightness, press the Fn button twice to open the
Fujitsu menu. Brightness can be adjusted from the
menu.
• The video timeout may have expired. Tap on the
display screen to reactivate the display. Note that this
is a normal, power-saving feature.
Cursor Is Not Tracking Pen
If the cursor on the screen appears to be misaligned with
the pen or is not accurately tracking the pen, calibrate the
pen. See “Calibrating the Pen” on page 25 for more information.
Infrared Data Transfer Is Not Working
If you are experiencing problems transferring data over
the system’s infrared interface, note the following:
• Can the IrDA port on the Tablet PC “see” the IrDA
port on the other device? A direct line-of-sight path
must exist between the IrDA port on the Tablet PC
and the IrDA port on the other device.
• The distance between the two devices must not be
more than 3 feet.
• The viewing angle from the IrDA port on the Tablet
PC must not be more than 15 degrees from a center
line between the IrDA port on the Tablet PC and the
IrDA port on the other device.
• The device with which you are trying to communicate
must be compliant with the IrDA Standard Revision
1.1 (or 1.0).
• It may be necessary for both computers to be using
the same network connection protocols.
Tablet PC is Not Responding to the Pen
If the Tablet PC does not respond to the pen, connect an
external keyboard to the system to see if it responds to
keyboard commands. If the system doesn’t respond to a
keyboard, the application or system may have crashed,
and it may be necessary to reboot the system. If the
system responds to a keyboard but not to a pen, contact
your local help desk or reseller, or call Fujitsu Service and
Support at 1-800-8Fujitsu (1-800-838-5487) for further
assistance.
Speaker/Headphone Volume Too Low
If the audio volume on your Tablet PC speaker or
external headphones is too low, check the following:
• Ensure the speaker (or headphone output if using
headphones) is enabled. To do so, open the Control
Panel and double-click on the Sounds and Audio
Devices icon. Select the proper tab, and increase the
volume using the slider bar. (If you aren’t getting any
sound, uncheck the Mute box if it is checked.)
• Press the Fn button twice to open the Fujitsu menu.
Volume can be adjusted from the menu.
• Ensure the mute box in the system volume control
(accessible from the system tray) is not set.
• Ensure any volume control in your audio software is
set to an audible level.
35
Osian_UG.book Page 36 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section Three
Configuring Peripheral Interfaces
Certain peripheral devices can be disabled during the
BIOS Setup. If the peripheral interface you want to use
does not appear to be working with your peripheral
device, ensure that it is enabled in the BIOS. Contact
your local help desk or reseller, or call Fujitsu Service
and Support at 1-800-8Fujitsu (1-800-838-5487) if you
need assistance using BIOS Setup.
RESTORING THE PRE-INSTALLED SOFTWARE
The Drivers and Applications Restore (DAR) DVD
contains sets of device drivers and Fujitsu utilities (in
specific directories) that are unique to your computer
configuration for use as documented below.
If you have access to the internet, visit the
Fujitsu Support website at: http://
www.computers.us.fujitsu.com/support to
check for the most current information,
drivers and hints on how to perform
recovery and system updates.
Re-Installing Individual Drivers and Applications
The Drivers and Applications CD can be used to
selectively re-install drivers and/or applications that may
have been uninstalled or corrupted.
There may be certain free third-party
applications pre-installed on your system
that are not on the DAR CD. The latest
versions of the applications can be
downloaded from the third-party’s website.
To re-install drivers and/or applications:
1. Boot up the system and insert the DAR CD after
Windows has started. A Fujitsu Installer screen is
displayed after the CD is inserted.
2. After reading the License Agreement, click [I agree].
3. A window will appear containing a list of applications, drivers, and utilities that you can install from
the Drivers and Applications CD.
The components listed are color-coded in
terms of their install status. Blue indicates
that the component can be installed. Green
indicates that the component needs to be
installed separately. Grey indicates a
component that is already installed; grey
items can be reinstalled, but prior to
installation you will receive a reminder that
the component is already installed.
4. In the list, check off all the components you want to
install. If you want to install all components, click
[Select All]. Clicking [Select All] will select all of the
36
blue-coded components; you must select grey and
green components separately.
5. Once you have selected the components you wish to
install, click [Install Selected Subsystems]; the
components will be installed.
6. After the components are installed, click [OK], then
click [Yes] when asked if you want to reboot the
system.
RESTORING THE FACTORY IMAGE
The Restore Disc only restores the primary
hard disk drive. If you have an optional
second hard disk drive installed, it will not
be restored using these utilities.
The Restore Disc that came with your system contains
two utilities:
■
■
The Recovery utility allows you to restore the original
contents of the C: drive.
The Hard Disk Data Delete utility on this disc is used
to delete all data on your hard disk and prevent it from
being reused. Do not use the Hard Disk Data Delete
utility unless you are absolutely certain that you want
to erase your entire hard disk, including all partitions.
• The use of this disc requires that you have
a device capable of reading DVDs
attached to your system. If you do not
have a built-in DVD player, you will need
to attach an external player. For more
information on available external devices,
visit our website at: us.fujitsu.com/
computers.
• This disc can only be used with the system
with which it was purchased.
BOOT Priority Change
Before restoring an image, you must first verify that your
system is set up to boot from the DVD drive. To verify/
change the boot-up priority (rather than booting-up
from the hard drive or an external floppy disk drive),
perform the following steps:
1. Start your system and press the [Ctl-Alt-Del] button
when the Fujitsu logo appears. You will enter the
BIOS Setup Utility.
2. Using the arrow keys, go to the Boot menu.
3. Arrow down to the Boot Device Priority submenu.
Press [Enter].
4. If “Optical Media Drive” or “CD-ROM Drive” is not
at the top of the list, arrow down to the drive in the
list, and press the space bar (or the + key) to move it
to the top of the list. (The system attempts to boot
Osian_UG.book Page 37 Monday, October 9, 2006 1:24 PM
Care and Maintenance
from the devices in the order in which they are
listed.). Note that the BIOS for some systems will
indicate “CD-ROM Drive”, even when a DVD drive is
connected.
5. If you have an external DVD drive connected,
proceed to the next step; otherwise, proceed to
step 7.
6. If you have an external DVD drive connected:
• Select the Advanced menu in the BIOS window.
• Scroll down to the USB Features submenu and
press the Enter key to open it.
• If Legacy USB Support is disabled, press the space
bar to enable it.
• Scroll down to SCSI SubClass Support and press
the space bar to enable it.
AUTOMATICALLY DOWNLOADING
DRIVER UPDATES
Your system has a convenient tool called the Fujitsu
Driver Update (FDU) utility. With FDU, you can choose
to automatically or manually go to the Fujitsu site to
check for new updates for your system.
The FDU icon
should appear in the system tray at
the bottom right of your screen (roll the cursor over the
icons to find the correct one). If the FDU icon does not
appear in the system tray, it can be started by going to
[Start] -> All Programs, and clicking on Fujitsu Driver
Update; this will create the icon automatically.
To invoke the FDU menu, right-click on the FDU icon.
The menu contains the following items:
■
Check for updates now
Allows for manual driver update search. The first time
it is used, you are prompted to agree to a user agreement. After clicking on the icon, the FDU automatically connects with the Fujitsu site to check for updates
and downloads them. While downloading, the icon
has a red bar through it, indicating that it cannot be
used while the download is in process. When the
update is complete, a message appears informing you
of the fact.
■
Enable Automatic Update Notifications
Automatically searches for new updates on a regular
basis (approximately every 3 days).
■
Show update history
Brings up a screen that displays a history of updates
that have been made via the FDU.
■
About Fujitsu Driver Update
Displays the FDU version number and copyright
information
■
Fujitsu Driver Update Readme
Displays the FDU readme.
7. Press [F10], then click on [Yes] to exit the BIOS Setup
Utility and return to the boot process.
After you have changed the boot priority, you can restore
a backup image when you are booting up.
Procedure
1.
Turn on the power to your system.
2.
Ensure that you have a device that can read DVDs
either installed in your system or attached externally
to it.
3.
Insert the Restore Disc into the drive tray.
4.
Reboot your system.
5.
After the system reboots, follow the instructions that
appear to either restore your system image or erase
all data from your hard disk.
37
Osian_UG.book Page 38 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section Three
38
Osian_UG.book Page 39 Monday, October 9, 2006 1:24 PM
4
System
Specifications
39
Osian_UG.book Page 40 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section Four
40
Osian_UG.book Page 41 Monday, October 9, 2006 1:24 PM
System Specifications
Stylistic ST5100 Series Hardware Specifications
The following table provides general hardware specifications of the Stylistic ST5100 Series Tablet PC by category.
Stylistic ST5100 Specifications (Continued)
10.4" Display
Stylistic ST5100 Specifications
• Active Digitizer
Processing Specifications
CPU
Intel® Core™ Duo Processor
ULV U2500*
Chip set
Intel 945GM - 533 MHz FSB
Processor
Speed
1.2 GHz*
• Outdoor-viewable
• 16-bit color
• 10.4” TFT XGA (1024 x 768),
16M colors
• Brightness: 8 levels
VRAM
Memory/Storage Specifications
Main RAM
• 2 DIMM slots available
• 200-pin SO DIMM modules
• DDR2 533 MHz
• 256 MB, 512 MB, 1 GB, and 2 GB
module configurations available,
with a system maximum of 4 GB.
L1 cache
(CPU)
32 KB on-die
L2 cache
2 MB on-die
BIOS ROM
2 MB or 1 MB depending upon your
configuration.
Hard disk
drive
Dimensions
12.1" Display (Active Digitizer):
12.77" x 8.66" x 0.82"-0.94"
(324.4 mm x 220 mm x 20.9-23.8 mm)
10.4" Display (Reflective Digitizer):
12.77" x 8.66" x 0.91"-1.01"
(324.4 mm x 220 mm x 23.2-25.7 mm)
Weight
3.5 lbs. (1.59 Kg) (with battery)
Interface Specifications
Card Slots
• Seriasl ATA 150
• Smart Card slot
• 5400 rpm
• Shock Sensor Technology
Integrated
Interfaces
• Modem (RJ-11)
• LAN (RJ-45)
• IEEE 1394 (S400 4-pin)
Display Specifications
Depending on the configuration of your system, it has
either a 12.1" transmissive or a 10.4" reflective display
12.1" Display
• PCMCIA: One Type I or Type II,
PCMCIA CardBus version 3.0
• Secure Digital (SD)/
Memory Stick slot
• SATA
• Shock-mounted
Up to 224 MB of shared memory using
Unified Memory Architecture (UMA).
Dynamically responds to application
requirements and allocates the proper
amount of memory for optimal graphics
and performance.
Physical Specifications
• 2.5” HDD
• 40 GB, 60 GB, 80 GB, 100 GB, or
120 GB HDD*
• Reflective Color LCD
• Indoor/Outdoor Viewability
• USB 2.0 (Qty. 2)
• DC-In
• IrDA
• Transmissive Color LCD
• Indoor/Outdoor Viewability
• 15-pin D-SUB connector for
external VGA monitor
• Active Digitizer
• Docking connector
• 16-bit color
• 12.1” TFT XGA (1024 x 768),
16M colors
• Brightness: 8 levels
• Viewing Angle:
Horizontal: 80 degrees (max.)
Vertical: 80 degrees (max.)
Infrared
IrDA version 1.1 (FIR, 4Mbps)
Keyboard/
Mouse
support
Keyboard/Mouse IR Port (Qty. 2)
• Contrast Ratio: Typ. 250, Min. 100
* The specifications for your particular model may vary.
To determine the specifications for your system, please
visit our website at: us.fujitsu.com/computers.
41
Osian_UG.book Page 42 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section Four
Stylistic ST5100 Specifications (Continued)
Wireless LAN
Your system may have one of the two
following Wireless LAN devices
installed:
Audio
Stylistic ST5100 Specifications (Continued)
Agency Approval Specifications
• EN55022 (CISPR22) Class B
Emissions
• VCCI Class B
Immunity
• EN55024 (1998)
• Integrated Atheros Super AG
Wireless LAN (802.11a/b/g)
Safety
• UL and cUL Listed, UL 60950,
3rd edition
• CB Report, IEC 60950, 3rd Edition
• Sigmatel STAC9753A codec
• Internal mono microphone and
speaker
• Dual digital microphones (12.1"
model only)
Specific
Absorption
Rate (SAR)
• Application Buttons, each with
primary, secondary, tertiary, and
security functions
• Emergency Shutoff Button (Power
Off button)
• Two Navigation buttons
Wireless
• Charge/DC-In
• Battery level
Telecom
Other
Security
Features
• Fingerprint Swipe Sensor (12.1"
model only)
• Trusted Platform Module (TPM)
• Microsoft® Windows®
XP Tablet PC Edition 2005
* Optional feature
• 6-cell NiMH, 35 mAh
• Life (with Standby on bridge
battery only):
5 minutes from full charge
• Autosensing 100 - 240V, supplying
16 VDC, with a current of 3.75 A
Environmental Specifications
Operating: 41o - 95o F (5o - 35o C)
Non-operational: 5o - 140o F
(-15o - 60o C)
42
• Security Panel
• 6-cell (standard), 10.8V, 5200 mAh,
56 Wh
• Warm-swappable
Humidity
• Energy Star
Operating
Systems
• Removable, Lithium ion
Temperature
• IC CS-03
Power Specifications
• 9-cell (optional), 10.8V, 7800 mAh,
84 Wh
AC Adapter
• FCC Part 68
Additional Specifications
• Security
Bridge Battery
• FCC 15E
• RSS220
• HDD
Main Battery
• EN301893
• RSS210
• Power
Status
Indicators
(LEDs)
• ACA/EN
• EN301489
• Fingerprint swipe sensor for
biometric security (12.1" model
only)
• Power On/Suspend/Resume button
• FCC/RSS
• EN300328
• Stereo headphone jacks
User Controls
• FCC 15/15E, Class B
• Integrated Intel PRO/Wireless
3945ABG Network Connections
(802.11a+b/g)
Operating: 20 - 85% non-condensing
Non-operating: 8 - 85% noncondensing
Osian_UG.book Page 43 Monday, October 9, 2006 1:24 PM
System Specifications
Regulatory Information
NOTICE
Changes or modifications not expressly approved by
Fujitsu could void this user’s authority to operate the
equipment.
FCC NOTICES
Notice to Users of Radios and Television
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
■
■
■
■
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet that is on a
different circuit than the receiver.
Consult the dealer or an experienced radio/TV
technician for help.
Shielded interconnect cables must be employed with this
equipment to ensure compliance with the pertinent RF
emission limits governing this device.
Notice to Users of the US Telephone Network
This equipment complies with Part 68 of the FCC rules,
and the requirements adopted by ACTA. On the bottom
of this equipment is a label that contains, among other
information, the FCC registration number and ringer
equivalence number (REN) for this equipment; or a
product identifier in the format US:AAAEQ##TXXXX. If
requested, this information or number must be provided
to the telephone company.
This equipment is designed to be connected to the telephone network or premises wiring using a standard jack
type USOC RJ11C. A plug and jack used to connect this
equipment to the premises wiring and telephone network
must comply with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this
product. It is designed to be connected to a compatible
modular jack that is also compliant.
The ringer equivalent number (REN) of this equipment
is 0.1B as shown on the label. The REN is used to determine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone may result
in the devices not ringing in response to an incoming
call. In most but not all areas, the sum of RENs should
not exceed five (5.0). To be certain of the number of
devices that may be connected to a line, as determined by
the total RENs, contact the local telephone company.
If this equipment causes harm to the telephone network,
the telephone company will notify you in advance that
temporary discontinuance of service may be required.
But if advance notice isn’t practical, the telephone
company will notify the customer as soon as possible.
Also, you will be advised of your right to file a complaint
with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that could
effect the operation of the equipment. If this happens the
telephone company will provide advance notice in order
for you to make necessary modifications to maintain
uninterrupted service.
If trouble is experienced with this equipment, for repair
or warranty information, please refer to the manual or
contact Fujitsu Computer Systems Corporation,
Customer Service. If the equipment is causing harm to
the telephone network, the telephone company may
request that you disconnect the equipment until the
problem is resolved.
The equipment cannot be used on public coin service
provided by the telephone company. Connection to party
line service is subject to state tariffs. (Contact the state
public utility commission, public service commission or
corporation commission for information).
If your home has specially wired alarm equipment
connected to the telephone line, ensure the installation of
this computer does not disable your alarm equipment. If
you have any questions about what will disable alarm
equipment, consult your telephone company or a qualified installer.
The Telephone Consumer Protection Act of 1991 makes
it unlawful for any person to use a computer or other
electronic device to send any message via a telephone fax
machine unless such message clearly contains in a margin
at the top or bottom of each transmitted page or on the
first page of the transmission, the date an time it is sent
and an identification of the business or other entity, or
other individual sending the message and the telephone
number of the sending machine or such business, other
entity, or individual.
43
Osian_UG.book Page 44 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Section Four
DOC (INDUSTRY CANADA) NOTICES
Notice to Users of Radios and Television
This Class B digital apparatus meets all requirements of
Canadian Interference-Causing Equipment Regulations.
CET appareil numérique de la class B respecte toutes les
exigence du Réglement sur le matérial brouilleur du
Canada.
Notice to Users of the Canadian Telephone Network
NOTICE: This equipment meets the applicable Industry
Canada Terminal Equipment Technical Specifications.
This is confirmed by the registration number. The
abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada
technical specifications were met. It does not imply that
Industry Canada approved the equipment.
Before connecting this equipment to a telephone line the
user should ensure that it is permissible to connect this
equipment to the local telecommunication facilities.
The user should be aware that compliance with the
certification standards does not prevent service
degradation in some situations.
Repairs to telecommunication equipment should be
made by a Canadian authorized maintenance facility.
Any repairs or alterations not expressly approved by
Fujitsu or any equipment failures may give the telecommunication company cause to request the user to
disconnect the equipment from the telephone line.
NOTICE: The Ringer Equivalence Number (REN) for
this terminal equipment is 0.1B. The REN assigned to
each terminal equipment provides an indication of the
maximum number of terminals allowed to be connected
to a telephone interface. The termination on an interface
may consist of any combination of devices subject only
to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.
For safety, users should ensure that the
electrical ground of the power utility, the
telephone lines and the metallic water
pipes are connected together. Users should
NOT attempt to make such connections
themselves but should contact the appropriate electric inspection authority or electrician. This may be particularly important
in rural areas.
44
Avis Aux Utilisateurs Du Réseau
Téléphonique Canadien
AVIS: Le présent matériel est conforme aux spécifications techniques d’Industrie Canada applicables au
matériel terminal. Cette conformité est confirmée par le
numéro d’enregistrement. Le sigle IC, placé devant le
numéro d’enregistrement, signifie que l’enregistrement
s’est effectué conformément à une déclaration de
conformité et indique que les spécifications techniques
d’Industrie Canada ont été respectées. Il n’implique pas
qu’Industrie Canada a approuvé le matériel.
Avant de connecter cet équipement à une ligne téléphonique, l’utilisateur doit vérifier s’il est permis de
connecter cet équipement aux installations de télécommunications locales. L’utilisateur est averti que même la
conformité aux normes de certification ne peut dans
certains cas empêcher la dégradation du service.
Les réparations de l’équipement de télécommunications
doivent être effectuées par un service de maintenance
agréé au Canada. Toute réparation ou modification, qui
n’est pas expressément approuvée par Fujitsu, ou toute
défaillance de l’équipement peut entraîner la compagnie
de télécommunications à exiger que l’utilisateur déconnecte l’équipement de la ligne téléphonique.
AVIS: L’indice d’équivalence de la sonnerie (IES) du
présent matériel est de 0.1B. L’IES assigné à chaque
dispositif terminal indique le nombre maximal de
terminaux qui peuvent être raccordés à une interface
téléphonique. La terminaison d’une interface peut
consister en une combinaison quelconque de dispositifs,
à la seule condition que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.
Pour assurer la sécurité, les utilisateurs
doivent vérifier que la prise de terre du service d’électricité, les lignes télphoniques et
les conduites d’eau métalliques sont connectées ensemble. Les utilisateurs NE
doivent PAS tenter d’établir ces connexions eux-mêmes, mais doivent contacter
les services d’inspection d’installations
électriques appropriés ou un électricien.
Ceci peut être particulièrement important
en régions rurales.
Osian_UG.book Page 45 Monday, October 9, 2006 1:24 PM
Appendix A
Wireless LAN/Bluetooth*
User’s Guide
* Optional devices
45
Osian_UG.book Page 46 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Appendix A
46
Osian_UG.book Page 47 Monday, October 9, 2006 1:24 PM
W i r e l e s s L A N U s e r ’s G u i d e
FCC REGULATORY INFORMATION
1.
2.
3.
Reorient or relocate the receiving antenna.
Increase the distance between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from
the one the receiver is connected to.
Consult the dealer or an experienced radio/TV technician for
help.
Please note the following regulatory information related to the
optional wireless LAN module.
4.
Regulatory Notes and Statements
Wireless LAN, Health and Authorization for use
FCC Radio Frequency Exposure statement
Radio frequency electromagnetic energy is emitted from Wireless
LAN devices. The energy levels of these emissions, however, are far
much less than the electromagnetic energy emissions from wireless
devices such as mobile phones. Wireless LAN devices are safe for
use by consumers because they operate within the guidelines found
in radio frequency safety standards and recommendations. The use
of Wireless LAN devices may be restricted in some situations or
environments, such as:
■
On board an airplane, or
■
In an explosive environment, or
■
In situations where the interference risk to other devices or services is perceived or identified as harmful.
In cases in which the policy regarding use of Wireless LAN devices
in specific environments is not clear (e.g., airports, hospitals, chemical/oil/gas industrial plants, private buildings), obtain authorization to use these devices prior to operating the equipment.
Regulatory Information/Disclaimers
Installation and use of this Wireless LAN device must be in strict
accordance with the instructions included in the user documentation provided with the product. Any changes or modifications
made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The
manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, or the
substitution or attachment of connecting cables and equipment
other than those specified by the manufacturer. It is the responsibility of the user to correct any interference caused by such unauthorized modification, substitution or attachment. The
manufacturer and its authorized resellers or distributors will
assume no liability for any damage or violation of government
regulations arising from failure to comply with these guidelines.
This device must not be co-located or operating in conjunction
with any other antenna or transmitter.
Federal Communications Commission statement
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause interference, and, (2) This device must accept
any interference, including interference that may cause undesired
operation of this device.
FCC Interference Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy.
If not installed and used in accordance with the instructions, it may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
The available scientific evidence does not show that any health
problems are associated with using low power wireless devices.
There is no proof, however, that these low power wireless devices
are absolutely safe. Low power wireless devices emit low levels of
radio frequency energy (RF) in the microwave range while being
used. Whereas high levels of RF can produce health effects (by
heating tissue), exposure to low-level RF that does not produce
heating effects causes no known adverse health effects. Many
studies of low-level RF exposure have not found any biological
effects. Some studies have suggested that some biological effects
might occur, but such findings have not been confirmed by additional research. The wireless LAN radio device has been tested and
found to comply with FCC radiation exposure limits set forth for an
uncontrolled equipment and meets the FCC radio frequency (RF)
Exposure Guidelines in Supplement C to OET65.
The maximum SAR values measured from the devices are:
■
■
■
■
Intel PROSet Wireless LAN (WM3945ABG): 1.47 W/kg
Atheros Wireless LAN (AR5BX6): 1.57 W/kg
Intel PROSet Wireless LAN (WM3945ABG) + Bluetooth
Simultaneous: 1.47 W/kg
Atheros Wireless LAN (AR5BX6) + Bluetooth Simultaneous:
1.56 W/kg
Export restrictions
This product or software contains encryption code which may not
be exported or transferred from the US or Canada without an
approved US Department of Commerce export license. This device
complies with Part 15 of FCC Rules., as well as ICES 003 B / NMB
003 B. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may
cause undesirable operation. Modifications not expressly authorized by Fujitsu Computer Systems Corporation may invalidate the
user's right to operate this equipment.
Canadian Notice
The device for the 5150-5250 MHz band is only for indoor usage to
reduce the potential for harmful interference to co-channel mobile
satellite systems.
The maximum antenna gain of 6 dBi permitted (for devices in the
5250-5350 MHz, 5470-5725, and 5475-5825 MHz bands) to comply
with the e.i.r.p. limit as stated in A9.2 of RSS210.
In addition, users should also be cautioned to take note that high
power radars are allocated as primary users (meaning they have
priority) of 5250-5350 MHz and 5650-5850 MHz and these radars
could cause interference and/or damage to LE-LAN devices.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try and correct the interference
by one or more of the following measures:
47
Osian_UG.book Page 48 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Appendix A
Before Using the Wireless LAN
This manual describes the procedures required to properly setup and configure the integrated Wireless LAN
Mini-PCI device (referred to as "WLAN device" in the
rest of the manual). Before using the WLAN device, read
this manual carefully to ensure it's correct operation.
Keep this manual in a safe place for future reference.
Wireless LAN Devices Covered by this Document
This document is applicable to systems containing one
of the following two devices. Most of the procedures are
identical. Sections that differ between the two devices
have been noted in the text:
■
■
Intel® PRO/Wireless 3945ABG (WM3945ABG)
Network Connection (802.11a+b/g)
Atheros® AR5006EXS (AR5BXB6) Mini-Card
Wireless network card (802.11a+b/g)
Characteristics of the WLAN Device
■ The WLAN device is a Mini-PCI card attached to the
main board of the mobile computer.
■
■
■
It operates in two license-free RF bands, therefore
eliminating the need to procure an FCC license to
operate. It operates in the 2.4GHz Industrial, Scientific, and Medical (ISM) RF band and in the lower and
middle bands of the 5GHz Unlicensed National Information Infrastructure (UNII) bands.
The WLANs are capable of three operating modes,
IEEE802.11a, IEEE802.11b and IEEE802.11g, wireless
LAN standards governed by the IEEE (Institute of
Electronics and Electrical Engineers).
Encoding of data is modulated using Direct Sequence
Spread Spectrum (DSSS) and Complementary Code
Figure A-1. Ad Hoc Mode Network
48
Keying (CCK) when the WLAN device is operating in
IEEE 802.11b mode and Orthogonal Frequency Division Multiplexing (OFDM) when operating in
IEEE802.11a or IEEE802.11g mode.
■
The WLAN device is Wi-Fi certified and operates at
the maximum data transfer rate of 54 Mbps in
IEEE802.11a or IEEE802.11g mode and 11 Mbps in
IEEE802.11b mode.
■
The WLAN device supports the following encryption
methods - WEP, TKIP, and AES encryption.
Wireless LAN Modes Using this Wireless Module
Ad Hoc Mode (See Figure A-1)
“Ad Hoc Mode” refers to a type of wireless network that
involves connecting multiple computers without the use
of an Access Point. Network connectivity between
computers can be established using only wireless LAN
cards in a peer-to-peer fashion.
Ad Hoc networks are an easy and inexpensive method
for establishing network connectivity between multiple
computers.
In Ad Hoc mode, you can use Microsoft Network functions, such as File and Print Sharing to share folders,
printers, or other peripheral devices, and exchange files
with other computers.
To use Ad Hoc Mode, you must set the same SSID and
the same encryption key for all the computers that are
connected. Communication between computers in an
Ad Hoc network will occur provided they are within
each other’s RF coverage area.
Osian_UG.book Page 49 Monday, October 9, 2006 1:24 PM
W i r e l e s s L A N U s e r ’s G u i d e
Figure A-2. Access Point (Infrastructure) Mode Network
Wired LAN
Internet
ADSL modem,
cable modem,
or similar
Access Point*
Wireless LAN
* An optional hub for a wired
LAN may be required depending
upon the type of access point used.
Access Point (Infrastructure) Mode (See Figure A-2)
Infrastructure mode refers to a wireless network in which
devices communicate with each other by first going
through an Access Point (AP). In infrastructure mode,
wireless devices can communicate with each other or can
communicate with a wired network. Most corporate
wireless LANs operate in infrastructure mode because
they require access to the wired LAN in order to use
services such as file servers or printers.
How to Handle This Wireless Module
The Integrated Wireless LAN device is already installed in
your mobile computer. Under normal circumstances, it
should not be necessary for you to remove or re-install it.
The wireless LAN has been configured to support the
operating system with which your system shipped.
FOR BETTER COMMUNICATIONS
This personal computer may not operate properly due to
the operating environment. It is highly recommended
that you observe the following precautions when using
your wireless LAN module:
■
For optimum wireless communications, it recommended that operation of the wireless LAN module
occur within 25 meters of the Access Point. Wireless
range is dependent on a multitude of factors including
number of obstructions, walls, type of construction
material, reflective objects, etc.
■
If the computer is unable to communicate properly,
change the channel to be used or the installation location. During the use of a microwave oven or other
equipment generating strong high-frequency energy, in
particular, the personal computer may be highly susceptible to the energy and unable to communicate
properly.
■
Broadcast stations or wireless communication equipment that operate in the 2.4GHz or 5GHz RF Frequency band may interfere with the operation of the
wireless LAN module. Increasing of transmit power or
relocating Access Points may be necessary to combat
the effects of the interference.
STOPPING TRANSMISSION
To use this product inside hospitals, clinics, or airplanes,
or in other places where the use of electronic equipment
is regulated, stop the transmission of radio waves from
the wireless LAN beforehand.
Deactivation using the wireless switch
The transmission of radio waves from the wireless LAN
can be stopped by setting the wireless switch to the Off
position. Note that the wireless LAN On/Off switch has
no effect on non-wireless LAN models.
(See Figure A-3 for Wireless LAN switch location.)
49
Osian_UG.book Page 50 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Appendix A
To restart transmission, check the [Enable
Radio] checkbox to select it., then click the
[OK] button.
STARTING TRANSMISSION
Wireless LAN
On/Off
Switch
To communicate using the wireless LAN function, set
the computer to a status from which it can transmit, as
follows:
Intel PROSet Wireless LAN:
1.
Set the wireless switch to the On position.
2.
Click [Start] --> [(All) Programs] --> [Intel Network Adapters] --> [Intel(R) PROSet]. The
Intel(R) PROSet window will be displayed.
3.
Click the [General] tab if it is not already selected.
4.
Select [ON] for the Switch radio: function, then
click [OK]. Wireless communications on/off
switching will be activated and the transmission of
radio waves will be restarted.
Figure A-3. Wireless LAN On/Off Switch
Deactivation using Windows
Intel PROSet Wireless LAN:
Atheros Wireless LAN:
1.
Click [Start] --> [(All) Programs] --> [Intel Network Adapters] --> [Intel(R) PROSet]. The
Intel(R) PROSet window will be displayed.
1.
Click the Wireless Network Connection icon in the
system tray at the lower right of your screen.
2.
Click the General tab.
2.
3.
Select [Off] for the wireless communications
Switch Radio: function, and then click the [OK]
button. Wireless communications on/off switching
will be deactivated and the transmission of radio
waves from the wireless LAN will be stopped.
Click [Enable Radio]. The radio will be turned on.
Access Point Mode: Transmission is enabled.
Ad Hoc Mode: Restart your computer to enable the
radio.
To restart transmission, select [On] for the
wireless communications Switch Radio:
function, and then click the [OK] button.
Atheros Wireless LAN
1.
Click [Start] --> [All Programs] --> [Atheros] -->
[Atheros Client Utility].
2.
3.
Click [Action].
Click [Disable Radio]. Wireless communications
on/off switching will be deactivated and the transmission of radio waves from the wireless LAN will
be stopped.
50
Osian_UG.book Page 51 Monday, October 9, 2006 1:24 PM
W i r e l e s s L A N U s e r ’s G u i d e
Connecting the WLAN
FLOW OF OPERATIONS
The wireless LAN connection procedure contained in
this section is outlined below.
1.
2.
3.
Make sure the mobile computer is ready for the
transmission of radio waves from the wireless LAN.
For further details, see (See Starting Transmission
on page 50 for more information.).
Assign the parameters required for wireless LAN
connection. (See Preparation for wireless LAN connection on page 51 for more information.).
■
Configure network name (SSID).
■
Configure wireless LAN security parameters as
appropriate (e.g., WEP, TKIP, 802.1x/EAP).
Specify TCP/IP as the protocol, and confirm the name
of the work group and other settings.
■
Enter the data required for file/printer sharing on the
network. Perform this operation as required.
■
For access point (or “infrastructure”) connection,
configure the wireless module with appropriate
parameters required to associate to the access point
network.
■
Verify that you are able to connect your computer to
the network.
PREPARATION FOR WIRELESS LAN
CONNECTION
This section explains the preparations required to use
the wireless LAN when using the Windows XP Wireless
Zero Configuration Tool. Configuration can also be
accomplished using the wireless module (Intel or
Atheros) configuration utility.
■
You do not need to set the channel
when using access point (infrastructure)
mode. Channel selection is controlled by
the access point. In ad hoc networks,
channel selection defaults to channel 11;
however, channel selection can be manually changed if desired. This can be
accomplished only when using the client
utility.
1.
Make sure the Wireless LAN switch is switched on.
2.
Click the [Start] button first and then [Control
Panel].
3.
If the Control Panel is in Category view, switch to
Classic view by clicking “Switch to Classic View”
under Control Panel the left frame. (If you are
already in Classic view, “Switch to Category View”
will be displayed instead.)
4.
Double-click the Network Connections icon. A list
of currently installed networks will be displayed.
5.
Right-click [Wireless Network Connection] in the
list, and then click [Properties] in the menu displayed. The [Wireless Network Connection Properties] window will be displayed.
6.
Click the [Wireless Networks] tab.
7.
Click [Refresh], then choose the correct SSID from
the [Available Networks] window. Click [Configure] and proceed to step 10. If the SSID of your
access point does not appear in the list, click [Add].
The [Wireless Network Properties] window will be
displayed.
8.
Select the Association tab if it is not already
selected.
9.
Enter the information required for connection to
the wireless LAN.
Assigning parameters
Enter the network name (SSID), the network key, and
other data required for wireless LAN connection. If there
is the administrator of the network, contact the network
administrator for data settings.
To use access point (infrastructure) connection, refer to the access point manual
for the access point-setting procedure.
If it is necessary to change the channel,
change the setting of the access point.
For the setting procedure, refer to the
manual of the access point.
Perform setting operations relating to network connection. (See Connection to the network on page 53
for more information.)
■
■
a. Enter the network name (SSID). (i.e., Enter the
name of the desired network in less than 33
ASCII characters).
51
Osian_UG.book Page 52 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Appendix A
For ad hoc connection: Assign the same network
name to all the personal computers to be
connected.
For access point (infrastructure) connection:
Assign the appropriate SSID. The SSID must be
identical to the SSID of the access point. Refer to
the access point manual, or contact your network
administrator.
b. For ad hoc connection, check the following field.
For access point (infrastructure) connection,
clear the check mark for the following field:
[This is a computer-to-computer (ad hoc) network; wireless access points are not used.]
10. Choose the appropriate Network Authentication
type. Options are Open, Shared, WPA, or WPAPSK. Please contact your network administrator for
the correct setting.
It is strongly recommended that you enter
the network key for encoding
communications data. If the network key
is not entered, since the network can be
accessed from all personal computers
containing the wireless LAN function,
there is the danger of your data being
stolen or damaged by other users.
11. Choose the Data Encryption type. Options are
WEP, TKIP, or AES. The latter two encryption
methods are available only when the Network
Authentication scheme is WPA or WPA-PSK. WEP,
TKIP, and AES are different methods used to
encrypt communications data. Proceed to Step 11a
if using static WEP keys, otherwise proceed to step
12.
a. Clear the check mark from the [The key is
provided for me automatically] check box.
b. Enter data in [Network Key]. Depending on the
number of entered characters or digits, whether
the key is an ASCII character code or a hexadecimal code will be identified automatically.
■
■
52
Use five or thirteen characters to enter the key in
the ASCII character code format. The characters
that can be used as the “network key” are as follows: 0 - 9, A - Z, _ (underscore), or,
Use 10 or 26 characters to enter the key in the
hexadecimal character code format. The characters that can be used as the “network key” in this
case are as follows: 0- 9, A - Z, a - f
For ad hoc connection: Assign the same network
key to all the personal computers to be connected.
For access point (infrastructure) connection:
Assign the identical network key that is programmed into the access point. For this setting,
refer to the access point manual or contact your
network administrator.
c. Confirm the Network key by re-entering the
same data in the [Confirm network key:] field.
d. Make sure that the key index used is identical to
the key index used by the Access Point(s).
12. Click the [Authentication] tab and then verify the
settings of [Enable network access control using
IEEE 802.1x].
For internal use at an organization such as a company, when access by wireless LAN clients is to be
limited using IEEE 802.1x authentication, check the
[Enable network access control using IEEE 802.1x]
check box.
For home use, clear the check mark from [Enable
network access control using IEEE 802.1x].
For the setting method relating to IEEE 802.1x
authentication, refer to the manual of the access
point which you are using.
13. After completion of setting operations, click the
[OK] button. Processing will return to the [Wireless Network Connection Properties] window.
14. Verify that the network name entered in step 7
above is added in [Preferred Networks], and then
click the [OK] button.
In [Preferred Networks], register only the
desired connection settings.
15. Close the [Wireless Network] window.
Osian_UG.book Page 53 Monday, October 9, 2006 1:24 PM
W i r e l e s s L A N U s e r ’s G u i d e
CONNECTION TO THE NETWORK
This section explains connection to the network.
If there is an administrator of the network, contact the
network administrator for data settings.
Following this operation, confirm the names of the
computer and the workgroup as follows.
Confirming the computer and work group names
To modify the computer name and/or the
work group name, you need to be logged
in from Windows as an administrator.
Setting the network
Perform the “Setting TCP/IP” and “Confirming the
computer and work group names” operations required for
network connection.
Setting TCP/IP
1.
Click the [Start] button, then [Control Panel].
2.
If the Control Panel is in Category view, switch to
Classic view by clicking “Switch to Classic View”
under Control Panel the left frame. (If you are
already in Classic view, “Switch to Category View”
will be displayed.)
3.
Double-click the [System] icon. The [System Properties] window will be displayed.
4.
Click the [Computer Name] tab.
5.
Confirm the settings of [Full computer name:] and
[Workgroup:].
To change the setting of the IP address,
you need to be logged in from Windows
as an administrator.
1.
Click the [Start] button first and then [Control
Panel].
2.
If the Control Panel is in Category view, switch to
Classic view by clicking “Switch to Classic View”
under Control Panel the left frame. (If you are
already in Classic view, “Switch to Category View”
will be displayed.)
3.
Double-click [Network Connections]. A list of currently installed networks will be displayed.
4.
Right-click [Wireless Network Connection] in the
list, and then click [Properties] in the menu displayed. The [Wireless Network Connection Properties] window will be displayed.
5.
Click the [General] tab if it is not already selected.
6.
Click [Internet Protocol (TCP/IP] and then click
[Properties]. The [Internet Protocol (TCP/IP)
Properties] window will be displayed.
7.
Set the IP address as follows:
■
■
a. The setting of [Full computer name:] denotes the
name for identifying the computer. Any name
can be assigned for each personal computer.
To change the name, click [Change] and
then proceed in accordance with the
instruction messages displayed on the
screen.
Enter the desired name in less than 15 ASCII
character code format. Identifiability can be
enhanced by entering the model number, the
user name, and other factors.
b. [Workgroup name] is the group name of the
network. Enter the desired name in less than 15
ASCII character code format.
For ad hoc connection: Select [Use the following
IP address:] and then enter data for [IP address]
and [Subnet mask]. See page 62 for IP address
setting.
For access point (infrastructure) connection: If
your network uses DHCP, select [Obtain an IP
address automatically] and [Obtain DNS server
address automatically]. If your network uses static
IP addresses, consult with your network administrator for the correct IP address settings.
8. Click the [OK] button. Processing will return to the
[Wireless Network Connection Properties] window.
9. Click the [OK] button.
10. Close the [Network Connection] window.
For ad hoc connection: Assign the same network
name to all personal computers existing on the
network.
For access point (infrastructure) connection:
Assign the name of the work group to be
accessed.
6.
Click the [OK] button. If a message is displayed
that requests you to restart the personal computer,
click [Yes] to restart the computer.
Setting the sharing function
Set the sharing function to make file and/or printer sharing
with other network-connected personal computers valid.
53
Osian_UG.book Page 54 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Appendix A
This operation is not required unless the sharing function is to be used.
2.
Double-click [Local disk (C:)].
3.
Right-click the “work” folder (or whichever folder
you want to share), and then click [Sharing and
Security...] in the menu displayed. The [Folder
Name Properties] window will be displayed.
The folder and printer for which the sharing function
has been set will be usable from any personal computer
present on the network.
To share a file and/or the connected
printer, you need to be logged in as an
administrator.
Setting the file-sharing function for the file
which has been used to execute Network
Setup Wizard is suggested on the screen.
For the wireless LAN, however, since
security is guaranteed by entry of the
network name (SSID) and the network
key, the steps to be taken to set the filesharing function easily without using
Network Setup Wizard are given below.
Setting the Microsoft network-sharing service
1.
Click the [Start] button first and then [Control
Panel].
2.
If the Control Panel is in Category view, switch to
Classic view by clicking “Switch to Classic View”
under Control Panel the left frame. (If you are
already in Classic view, “Switch to Category View”
will be displayed.)
3.
Double-click [Network Connections]. A list of currently installed networks will be displayed.
4.
Right-click [Wireless Network Connection] in the
list, and then click [Properties] in the menu displayed. The [Wireless Network Connection Properties] window will be displayed.
5.
If [File and Printer Sharing for Microsoft Networks] is displayed, proceed to step 6. If [File and
Printer Sharing for Microsoft Networks] is not displayed, skip to step 7.
6.
Make sure that the [File and Printer Sharing for
Microsoft Networks] check box is checked, and
then click the [OK] button. Skip to “Setting filesharing function”.
7.
Click [Install]. The [Select Network Component
Type] window will be displayed.
8.
Click [Service], then click the [Add] button. The
[Select Network Service] window will be displayed.
9.
Click [File and Printer Sharing for Microsoft Networks] and then click the [OK] button. Processing
will return to the [Wireless Network Connection
Properties] window, and [File and Printer Sharing
for Microsoft Networks] will be added to the list.
4.
Click [Sharing] if it isn’t already selected.
5.
Click the link stating “If you understand the security risks, but want to share files without running
the wizard, click here”.
6.
Click “Just enable file sharing” and click [OK].
7.
Check the [Share this folder on the network] check
box.
To specify the corresponding folder as a
read-only folder, select the [Read only]
checkbox under the General tab.
8.
Setting the printer-sharing function
1.
Click the [Start] button first and then [Printers and
FAX]. A list of connected printers will be displayed.
2.
Right-click the printer for which the sharing function is to be set, and then click [Sharing] in the
menu displayed. The property window corresponding to the selected printer will be displayed.
Setting the printer-sharing function when
Network Setup Wizard has been executed
is suggested on the screen. For the wireless
LAN, however, since security is guaranteed
by entry of the network name (SSID) and
the network key, the steps to be taken to
set the printer-sharing function without
using Network Setup Wizard are laid down
below.
10. Click the [Close] button.
Setting the file-sharing function
The procedure for setting the file-sharing function
follows, with the “work” folder in drive C: as an
example.
1.
54
Click the [Start] button first and then [My Computer].
Click the [OK] button. The folder will be set as a
sharable folder, and the display of the icon for the
“work.” folder will change.
3.
Click the [Sharing] tab.
4.
Click [Share this printer].
Osian_UG.book Page 55 Monday, October 9, 2006 1:24 PM
W i r e l e s s L A N U s e r ’s G u i d e
5.
Enter the sharing printer name in [Share name].
6.
Click the [OK] button.
■
Mode
If access point (infrastructure) connection is in
use, “Infrastructure (AP)” will be displayed. If ad
hoc connection is in use, “Ad hoc (Peer-to-peer)”
will be displayed.
■
Security
Displays the encryption type currently used by
the radio.
■
Speed
Displays the current data rate used by the radio to
transmit and receive data.
■
Band (Frequency)
The current operating frequency band is
displayed. When communication is possible,
“802.11b (2.4 GHz)” is displayed.
■
Channel
The channel number currently being used for the
communications is displayed.
Confirming connection
After you have finished the network setup operations,
access the folder whose sharing has been set for other
personal computers. Also, confirm the status of the radio
waves in case of trouble such as a network connection
failure.
In the case of access point (infrastructure)
connection, enter the necessary data for
the access point before confirming
connection. Refer to the manual of the
access point for the access point setup
procedure.
Connecting your personal computer to another
personal computer
1.
2.
Click [Start] first and then [My Computer]. The
[My Computer] window will be displayed in the left
frame.
Click [My Network Places] in the “Other Places”
list. The window [My Network Places] will be displayed.
3.
Click [View workgroup computers] under Network
Tasks in the left frame.
4.
Double-click the personal computer to which your
personal computer is to be connected. The folder
that was specified in “Setting the file-sharing function” on page 54 will be displayed.
5.
Double-click the folder to be accessed.
Confirming the status of the radio
Intel PROSet Wireless LAN:
1.
Click [Start] -> [All Programs] -> [Intel Network
Adapters] -> [Intel(R) PROSet]. The [Intel(R)
PROSet] window will be displayed.
2.
Click the [General] tab and confirm radio status in
the window displayed. The current connection status will be displayed.
■
Signal Quality
The quality of the signals is displayed on a graph.
■
Network name (SSID)
The connected network name (SSID) is displayed.
■
Profile name
“<No profile>” is displayed.
If connection cannot be made to the network or if you
want to check for normal connection, see “Troubleshooting” on page 58.
Atheros Wireless LAN:
1.
Right-click the Atheros icon in the lower right corner of the screen.
2.
Click [Open Client Utility]. The Atheros Wireless
Configuration Utility window opens.
3.
Contained within the Current Status tab and
Advanced Current Status, you will find the current
operating status of the radio. (When the radio is
turned off or the computer is not yet connected,
some of the conditions will not be displayed.)
■
Profile Name
The current configuration profile is displayed.
■
Network Type - Configured Network Type
[Access Point] or [AdHoc] will be displayed.
■
Current Mode
Indicates the frequency and data rate currently
used by the radio.
■
Current Channel
The channel number currently used by the radio.
■
Link Status
Displays the current connected state of the
WLAN module.
■
Encryption Type
Displays the encryption type currently used by
the radio.
55
Osian_UG.book Page 56 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Appendix A
56
■
IP Address
Displays the current TCP/IP address assigned to
the WLAN adapter.
■
Country
The country with the country code for which the
radio is configured.
■
Transmit Power Level
Displays the current transmit power level of the
radio.
■
Network Name (SSID)
Displays the Network Name (SSID) currently
used by the radio.
■
Power Save Mode
Displays the configured Power Save Mode
currently used by the radio. [Off], [Normal], or
[Maximum] will be displayed.
■
BSSID
Displays the Basic Service Set Identifier. This is
typically the MAC address of the Access Point or
in the case of AdHoc networks, is a randomly
generated MAC address.
■
Frequency
Displays the center frequency currently being
used by the radio.
■
Transmit Rate
Displays the current data rate used by the radio
to transmit data.
■
Receive Rate
Displays the current data rate used by the radio
to receive data.
Osian_UG.book Page 57 Monday, October 9, 2006 1:24 PM
W i r e l e s s L A N U s e r ’s G u i d e
Other settings
SETTING OF POWER-SAVING FUNCTION
You can set the power-saving function of wireless LAN.
Default setting is auto-setting. In case of using the powersaving function, manually control the communication
performance.
Intel PROSet Wireless LAN:
1.
Click [Start] -> [(All) Programs] -> [Intel Network
Adapters] -> [Intel(R) PROSet]. The Intel(R)
PROSet window will be displayed.
2.
Click the [Adapter] tab.
3.
Click the [Configure] button in [Power settings].
The [Power settings] window will be displayed.
4.
Select [Manual], and adjust the bar to set the powersaving function.
Setting of transmission power during ad hoc
connection
By controlling the transmission power during ad hoc
connection, you can broaden or narrow the communication range. This setting is only effective during ad hoc
connection. It will be ineffective during access point
connection.
Intel PROSet Wireless LAN:
1.
Click [Start] -> [(All) Programs] -> [Intel Network
Adapters] -> [Intel(R) PROSet]. The Intel(R)
PROSet window will be displayed.
2.
Click the [Adapter] tab.
3.
Click the [Configure] button in [Ad hoc settings].
The [Ad hoc settings] window will be displayed.
4.
Change channels during ad hoc connection by
selecting a new channel from the drop down list.
5.
Click [OK].
Atheros Wireless LAN:
1.
Click on the My Computer icon. Select [View system information] from the left frame.
2.
Select the Hardware tab and click [Device Manager].
3.
Double-click “Atheros Wireless LAN Adapter”
under [Network Adapters].
4.
In the Atheros Wireless LAN Adapter window, select
the Advanced tab.
5.
Select IBSS Channel Number from the list, and
change the value from the [Value:] dropdown list to
the desired channel.
6.
Click [OK].
Intel PROSet Wireless LAN:
1.
Click [Start] -> [(All) Programs] -> [Intel Network
Adapters] -> [Intel(R) PROSet]. When the Intel(R)
PROSet window is displayed, click [Advanced].
2.
Click the [Adapter] tab.
3.
Click the [Configure] button in [Power settings].
The [Power settings] window will be displayed.
4.
Adjust the “Transmission Power (Ad Hoc)” bar to
set the transmission power.
Setting of channels during ad hoc connection
You can set channels during ad hoc connection. Channel
11 is set by default. When connecting to an existing ad
hoc network, no channel setting will be effective.
This setting is only effective during ad hoc connection; it
will be ineffective during access point connection.
When changing channels during ad hoc
connection, change the channel settings of
all connected computers with the same
Network name (SSID) at the same time.
After changing the channels, turn off all
computers and -- after they are all turned
off -- turn them back on.
57
Osian_UG.book Page 58 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Appendix A
Troubleshooting
Causes and countermeasures for troubles you may encounter while using your wireless LAN are described in the
following table.
Problem
Unavailable
network
connection
Possible Cause
Incorrect network
name (SSID) or
network key
Possible Solution
Ad hoc connection: verify that the network names (SSID’s) and network
keys (WEP) of all computers to be connected have been configured
correctly. SSID’s and WEP key values must be identical on each machine.
Access Point (Infrastructure) connection: set the network name (SSID)
and network key to the same values as those of the access point.
Set the Network Authentication value identically to that of the Access
Point. Please consult your network administrator for this value, if
necessary.
For the method of setting network authentication, refer to the following
pages:· “Assigning parameters” on page 51·
Poor radio wave
condition
Ad hoc connection: Retry connection after shortening the distance to
the destination computer or removing any obstacles for better sight.
Access Point (Infrastructure) connection: Retry connection after shortening the distance to the access point or removing any obstacles for
better sight.
To check the wave condition, refer to the following pages:· “Confirming
the status of the radio waves” on page 55.·
Radio wave
transmission has
stopped
Check if the wireless switch is turned ON. Also verify “Disable Radio” is
not checked in “Network setting” window. Refer to “Starting Transmission” on page 50.
The computer to be
connected is turned
off
Check if the computer to be connected is turned ON.
Active channel
duplication due to
multiple wireless
LAN networks
If there is any other wireless LAN network nearby, change channels to
avoid active channel duplication. For the method of checking active
channels, refer to the following pages:· “Confirming the status of the
radio waves” on page 55·
No right of access to
the network to be
connected
Check if you have a right of access to the network to be connected with.
Incorrectlyperformed network
setting
Check the protocol, work group name or shared setting.
Unmatched
[Network
authentication
(shared mode)]
settings in Windows
XP
58
For the method of checking, refer to the following pages:· “Connection
to the Network” on page 53.
If the setting of [Network authentication (shared mode)] is not matched
with that of access point or computer to be connected with, no communication can be established. Check the parameter setting. Refer to
“Assigning parameters” on page 51.
Osian_UG.book Page 59 Monday, October 9, 2006 1:24 PM
W i r e l e s s L A N U s e r ’s G u i d e
Problem
Unavailable
network
connection
(continued)
Possible Cause
It takes too long to
retrieve the network
and display the
connected
computers.
Possible Solution
Retrieve computers as follow:
1. Click [Start] button, then click [Search].
2. Click [Computers or people].
3. Click [Computers on the network].
4. Input the name of computer to be connected with in [Computer
name] and click [Search].
5. Double-click the icon of connected computer.·
Incorrect setting of IP
address
Check the network setting.
“Setting the network” on page 53.
In case of using TCP/IP protocol, you can check IP address as follows:
1.
Click [Start] -> [All programs] -> [Accessories] ->
[Command prompt].·
2.
In [Command prompt] or [MS-DOS prompt] window, input
[IPCONFIG] command as follows, then press [Enter] key.
Example: In case of C drive being the hard disk:
C:\ipconfig [Enter]
Check that the IP address is correctly displayed:.
IP Address................: 10.0.1.3
Subnet Mask.............: 255.255.255.0
Default Gateway.........: 10.0.1.1
When IP address is displayed as [169.254.XXX.YYY] or [0.0.0.0],
IP address is not correctly fetched from the access point. In that
case, restart the computer itself. If the display is still unchanged,
check the setting of TCP/IP.
If [Cable Disconnected] or [Media Disconnected] is displayed
without showing IP address, check the setting of network name
(SSID) and network key. Also, set the network authentication
according to the access point.
Communication
is disconnected
soon after
connection to
the access point
Access control may
be disabled
Check the setting of “Enable network access control using IEEE
802.1X”.Refer to “Assigning parameters” on page 51.
When restricting the access of wireless LAN clients using IEEE802.1X
authentication, put a check mark on “Enable network access control
using IEEE 802.1X”.
When using at home, remove a check mark on “Enable network access
control using IEEE802.1X”.
For the method of setting related with IEEE802.1X authentication, refer
to the access point manual.
Authentication
method may have
been entered
incorrectly
Re-enter your WEP key and verify that your authentication method
(Open or Shared) is correct.
59
Osian_UG.book Page 60 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Appendix A
Wireless LAN Glossary
Access point
A designation of wireless LAN network configurations.
It indicates a form of communication using an Access
Point. For details, refer to “access point connection” on
page 48.
Ad hoc
A designation for wireless LAN network configuration.
It indicates a form of communication limited to those
personal computers which have wireless LAN function.
For details, refer to “Ad hoc connection” on page 48.
Channel
The frequency band of wireless LAN to be used in
communications over wireless LAN or at the access
point.
DHCP (Dynamic Host Configuration Protocol)
A protocol used for automatically fetching communication parameters such as IP addresses. The side which
assigns IP address is called DHCP server and the side
that is assigned it is called DHCP client.
DNS (Domain Name System)
A function that controls the correspondence of IP
addresses assigned to a computer with the name. Even
for those computers whose IP addresses are unknown, if
their names are known, it is possible to communicate
with them.
IEEE802.11a
One of the wireless LAN standards prescribed by the
802.11 committee in charge of establishing standards of
LAN technology in IEEE (Institute of Electrical and
Electronic Engineers). It allows communications at the
maximum speed of 54 Mbps by using a 5GHz band
which can freely be used without radio communication
license.
IEEE802.11b
One of the wireless LAN standards prescribed by the
802.11 committee in charge of establishing standards of
LAN technology in IEEE (Institute of Electrical and
Electronic Engineers). It allows communications at the
maximum speed of 11Mbps by a band of 2.4 GHz (ISM
band) which can freely be used without radio communication license.
IP address
An address used by computers for communicating in
TCP/IP environment. IP addresses have global and
60
private addresses. A global address is a unique address in
the world. A private address is a unique address within a
closed network.
LAN (Local Area Network)
An environment connecting computers within a relatively small range, such as the same floor and building.
MAC address (Media Access Control Address)
A physical address inherent to a network card. For
Ethernet, the top three bytes are controlled/assigned as a
vendor code. The remaining three bytes comprise the
code uniquely (to avoid duplication) controlled by each
vendor. As a result, there is no Ethernet card with the
same physical address in the world. In Ethernet, the
frame transmission/reception is performed based on this
address.
MTU (Maximum Transmission Unit)
The maximum size of data which can be transmitted at
one time in networks including the Internet. In an environment whose maximum size of data is too large to
correctly receive data, normal communications can be
restored by setting the size of MTU to a smaller value.
Network authentication
The method of authentication performed by wireless
LAN clients to connect with the access point. There are
two types: open system authentication and shared key
authentication. The type of authentication must be set
to each client and also coincide with the setting of access
point with which to communicate. Network authentication is sometimes called authentication mode.
Network key
Data that is used for encrypting data in data communication. The personal computer uses the same network
key both for data encryption and decryption, therefore,
it is necessary to set the same network key as the other
side of communication.
Network name (SSID: Service Set Identifier)
The network name is a unique identifier attached to the
WLAN packet header that acts as a password when the
client attempts to connect to a WLAN. The SSID differentiates one WLAN from another so all WLAN devices
attempting to connect to a specific WLAN must use the
same SSID. SSID’s are transmitted in cleartext, thus
supplying no security to the WLAN.
Osian_UG.book Page 61 Monday, October 9, 2006 1:24 PM
W i r e l e s s L A N U s e r ’s G u i d e
Open system authentication
An 802.11 wireless LAN authentication method. Open
System does not exchange any key or other information,
it is a simple request by the mobile station to be authenticated without verifying identity.
PPPoE (Point to Point Protocol over Ethernet)
A method of allowing the authentication protocol
adopted in telephone line connection (PPP) to be used
over an Ethernet.
Protocol
A procedure or rule of delivering data among computers.
Ordered data communication is allowed by making all
conditions required for communication including the
method of data transmission/reception and actions upon
communication errors into procedures.
Shared key authentication
An 802.11 wireless LAN authentication method. When a
client attempts to associate to an access point, the access
point will send a challenge to the client. The client
encrypts the challenge with the network key and sends it
back to the access point. If the access point can decrypt
the challenge, then authentication has succeeded.
SSID (Service Set Identifier)
See “Network name”
Subnet mask
TCP-IP network is controlled by being divided into
multiple smaller networks (subnets). IP address consists
of the subnet address and the address of each computer.
Subnet mask defines how many bits of IP address
comprise the subnet address. The same value shall be set
among computers communicating with each other.
TCP/IP (Transmission Control Protocol/Internet
Protocol)
A standard protocol of the Internet.
Wi-Fi
Short for “Wireless Fidelity”. A term meant to be used
generically when referring to any type of 802.11 network,
whether 802.11b, 802.11a, 802.11g, etc.
61
Osian_UG.book Page 62 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Appendix A
IP address information
IP addressing is much more complicated
than can be briefly explained in this
document. You are advised to consult with
your network administrator for additional
information.
If IP address is unknown, set IP address as follows:
If you have an access point (DHCP server) on the
network, set the IP address as follows:
[Obtain an IP address automatically]
A DHCP server is a server that
automatically assigns IP addresses to
computers or other devices in the network.
There is no DHCP server for the AdHoc
network.
If the IP address is already assigned to the computer in
the network, ask the network administrator to check the
IP address to be set for the computer.
If no access point is found in the network:
An IP address is expressed with four values in the range
between 1 and 255.
Set the each computer as follows: The value in parentheses is a subnet mask.
<Example>
Computer A: 192.168.100.2 (255.255.255.0)
Computer B: 192.168.100.3 (255.255.255.0)
Computer C: 192.168.100.4 (255.255.255.0)
:
:
Computer X: 192.168.100.254 (255.255.255.0)
62
Osian_UG.book Page 63 Monday, October 9, 2006 1:24 PM
W i r e l e s s L A N U s e r ’s G u i d e
Specifications
Item
Specification
Type of network
Conforms to IEEE 802.11a/802.11b/g (Wi-Fi based)*
Transfer rate
(Automatic switching)
54 Mbps maximum data rate
Active frequency
802.11b/g: 2400~2473 MHz
802.11a: 4900 ~ 5850 MHz
Number of channels
802.11a: 8 independent channels
802.11b/g: 11 channels, 3 non-overlapping channels
Typical operating distances**
802.11a: 40 ft. (12 m) @ 54 Mbps; 300 ft. (91 m) @ 6 Mbps
802.11b: 100 ft. (30 m) @ 11 Mbps; 300 ft. (91 m) @ 1 Mbps
802.11g: 100 ft. (30 m) @ 54 Mbps; 300 ft. (91 m) @ 1 Mbps
Security
Encryption Types - WEP, TKIP, AES***
WPA 1.0, WPA-2 compliant
Encryption Key lengths Supported: 64 bits and 128 bits
802.1x/EAP
Maximum recommended number of computers to
be connected over wireless LAN (during ad hoc
connection)
10 units or less ****
* “Wi-Fi based” indicates that the interconnectivity test of the organization which guarantees the interconnectivity of
wireless LAN (Wi-Fi Alliance) has been passed.
** The communication ranges shown above will increase or decrease depending on factors such as number of walls,
reflective material, or interference from external RF sources.
*** Encryption with network key (WEP) is performed using the above number of bits, however, users can set 40 bits/
104 bits after subtracting the fixed length of 24 bits.
**** Depending on practical environments, the allowable number of computers to be connected may be decrease
63
Osian_UG.book Page 64 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Appendix A
Using the Bluetooth Device
The Integrated Bluetooth module (EYTF3CSFT) is an
optional device available for Fujitsu mobile computers.
WHAT IS BLUETOOTH?
Bluetooth technology is designed as a short-range
wireless link between mobile devices, such as laptop
computers, phones, printers, and cameras. Bluetooth
technology is used to create Personal Area Networks
(PANs) between devices in short-range of each other.
WHERE TO FIND INFORMATION ABOUT
BLUETOOTH
The Bluetooth module contains a robust Help user’s
guide to assist you in learning about operation of the
Bluetooth device.
To access the Help file, click [Start] -> All Programs, and
click on Toshiba. Select Bluetooth, then select User’s
Guide.
For additional information about Bluetooth Technology,
visit the Bluetooth website at: www.bluetooth.com.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment.
The transmitters in this device must not be co-located or
operated in conjunction with any other antenna or
transmitter.
Canadian Notice
To prevent radio interference to the licensed service, this
device is intended to be operated indoors and away from
windows to provide maximum shielding. Equipment (or
its transmit antenna) that is installed outdoors is subject
to licensing.
Warranty
Users are not authorized to modify this product. Any
modifications invalidate the warranty.
This equipment may not be modified, altered, or
changed in any way without signed written permission
from Fujitsu. Unauthorized modification will void the
equipment authorization from the FCC and Industry
Canada and the warranty.
64
Osian_UG.book Page 65 Monday, October 9, 2006 1:24 PM
Appendix B
Security Device*
User’s Guide
* Availability varies by model
65
Osian_UG.book Page 66 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Appendix B
66
Osian_UG.book Page 67 Monday, October 9, 2006 1:24 PM
S e c u r i t y D e v i c e U s e r ’s G u i d e
Fingerprint Sensor Device
installation process. You will also be led through the
procedure of enrolling your first user into OmniPass.
INTRODUCING THE
FINGERPRINT SENSOR DEVICE
INSTALLING OMNIPASS
Your system may have a fingerprint sensor device on the
side of the display opposite the function buttons. The
device is a standard feature on 12.1” models; it is not
available on 10.4” models. (See Figure 1-2 on page 2 for
location)
If OmniPass has already been installed on your system,
skip this section and go directly to “User Enrollment” on
page 68. You can determine whether OmniPass has
already been installed by checking to see if the following
are present:
■
■
The presence of the gold key-shaped OmniPass icon in
the system tray at the bottom right of the screen.
The presence of the Softex program group in the
Programs group of the Start menu
System Requirements
The OmniPass application requires space on your hard
drive; it also requires specific Operating Systems (OS’s).
The minimum requirements are as follows:
■
Figure B-1 Fingerprint sensor
With a fingerprint sensor, you can avoid having to enter
a username and password every time you want to:
■
Log onto Windows
■
Recover from standby mode
■
Cancel a password-protected screen saver
■
Log into homepages that require a username and password
After you have “enrolled” - or registered - your fingerprint, you can simply swipe your fingertip over the
sensor for the system to recognize you.
The fingerprint sensor uses Softex OmniPass which
provides password management capabilities to
Microsoft Windows operating systems. OmniPass
enables you to use a "master password" for all Windows,
applications, and on-line passwords.
OmniPass requires users to authenticate themselves
using the fingerprint sensor before granting access to the
Windows desktop. This device results in a secure
authentication system for restricting access to your
computer, applications, websites, and other passwordprotected resources.
OmniPass presents a convenient graphical user interface, through which you can securely manage passwords, users, and multiple identities for each user.
GETTING STARTED
This section guides you through the preparation of your
system for the OmniPass fingerprint recognition
application. You will be led through the OmniPass
■
Windows XP Home Edition, Windows XP Professional or Windows 2000 operating system
At least 35 MB available hard disk space
Installing the OmniPass Application
If OmniPass is already installed on your system, go to
“User Enrollment” on page 68. Otherwise continue with
this section on software installation.
For installation, OmniPass requires that the
user installing OmniPass have
administrative privileges to the system. If
your current user does not have
administrative privileges, log out and then
log in as an administrator before
proceeding with OmniPass installation.
To install OmniPass on your system you must:
1. Insert the installation media for the OmniPass
application into the appropriate drive. If you are
installing from CD-ROM or DVD-ROM, you must
find and launch the OmniPass installation program
(setup.exe) from the media.
2. Follow the directions provided in the OmniPass
installation program. Specify a location to which
you would like OmniPass installed. It is recommended that you NOT install OmniPass in the root
directory (e.g. C:\).
3. Once OmniPass has completed installation you will
be prompted to restart you system. Once your
system has rebooted you will be able to use
OmniPass. If you choose not to restart immediately
after installation, OmniPass will not be available for
use until the next reboot.
The installation program automatically places an icon
(Softex OmniPass) in the Windows Control Panel as
well as a golden key shaped icon in the taskbar.
67
Osian_UG.book Page 68 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Appendix B
Verifying Information about OmniPass
After you have completed installing OmniPass and
restarted your system, you may wish to check the version
of OmniPass on your system.
To check the version information of OmniPass:
1. From the Windows Desktop, double-click the keyshaped OmniPass icon in the taskbar (usually
located in the lower right corner of the screen),
or,
Click the Start button, select Settings, and click
Control Panel (if you are using Windows XP you
will see the Control Panel directly in the Start menu;
click it, then click Switch to Classic View). Doubleclick Softex OmniPass in the Control Panel, and the
OmniPass Control Center will appear. If it does not
appear, then the program is not properly installed,
or,
Click the Start button, select Programs, and from
the submenu select the Softex program group, from
that submenu click OmniPass Control Center.
2. Select the About tab at the top of the OmniPass
Control Panel. The About tab window appears with
version information about OmniPass.
Uninstalling OmniPass
For uninstallation, OmniPass requires that
the user uninstalling OmniPass have
administrative privileges to the system. If
your current user does not have
administrative privileges, log out and then
log in as an administrator before
proceeding with OmniPass uninstallation.
To remove the OmniPass application from your system:
1. Click Start on the Windows taskbar. Select Settings,
and then Control Panel.
2. Double-click Add/Remove Programs.
3. Select OmniPass, and then click Change/Remove.
4. Follow the directions to uninstall the OmniPass
application.
5. Once OmniPass has finished uninstalling, reboot
your system when prompted.
USER ENROLLMENT
Before you can use any OmniPass features you must first
enroll a user into OmniPass.
Master Password Concept
Computer resources are often protected with passwords.
Whether you are logging into your computer, accessing
your email, e-banking, paying bills online, or accessing
68
network resources, you often have to supply credentials
to gain access. This can result in dozens of sets of credentials that you have to remember.
During OmniPass user enrollment a "master password”
is created for the enrolled user. This master password
“replaces” all other passwords for sites you register with
OmniPass.
Example: A user, John, installs OmniPass on his system
(his home computer) and enrolls an OmniPass user with
username “John_01” and password “freq14”. He then
goes to his webmail site to log onto his account. He
inputs his webmail credentials as usual (username
“John_02” and password “tablet”), but instead of
clicking [Submit], he directs OmniPass to Remember
Password. Now whenever he returns to that site,
OmniPass will prompt him to supply access credentials.
John enters his OmniPass user credentials (“John_01”
and “freq14”) in the OmniPass authentication prompt,
and he is allowed into his webmail account. He can do
this with as many websites or password protected
resources he likes, and he will gain access to all those
sites with his OmniPass user credentials (“John_01” and
“freq14”). This is assuming he is accessing those sites
with the system onto which he enrolled his OmniPass
user. OmniPass does not actually change the credentials
of the password protected resource. If John were to go to
an Internet cafe to access his webmail, he would need to
enter his original webmail credentials (“John_02” and
“tablet”) to gain access. If he attempts his OmniPass user
credentials on a system other than where he enrolled
that OmniPass user, he will not gain access.
The basic enrollment procedure assumes
you have no hardware authentication
devices or alternate storage locations that
you wish to integrate with OmniPass. If
you desire such functionality, consult the
appropriate sections after reviewing this
section.
Basic Enrollment
The Enrollment Wizard will guide you through the
process of enrolling a user. Unless you specified otherwise, after OmniPass installation the Enrollment Wizard
will launch on Windows login. If you do not see the
Enrollment Wizard, you can bring it up by clicking Start
on the Windows taskbar; select Programs; select Softex;
click OmniPass Enrollment Wizard.
1. Click Enroll to proceed to username and password
verification. By default, the OmniPass Enrollment
Wizard enters the credentials of the currently logged
in Windows user.
2. Enter the password you use to log in to Windows.
This will become the “master password” for this
Osian_UG.book Page 69 Monday, October 9, 2006 1:24 PM
S e c u r i t y D e v i c e U s e r ’s G u i d e
OmniPass user. In most cases, the Domain: value will
be your Windows computer name. In a corporate
environment, or when accessing corporate resources,
the Domain: may not be your Windows computer
name. Click [Next] to continue.
3. In this step OmniPass captures your fingerprint.
Refer to “Enrolling a Fingerprint” on page 69 for
additional information.
4. Next, choose how OmniPass notifies you of various
events. We recommend you keep Taskbar Tips on
Beginner mode taskbar tips and Audio Tips on at
least Prompt with system beeps only until you get
accustomed to how OmniPass operates. Click [Next]
to proceed with user enrollment. You will then see a
Congratulations screen indicating your completion
of user enrollment.
5. Click [Done] to exit the OmniPass Enrollment
Wizard. You will be asked if you’d like to log in to
OmniPass with your newly enrolled user; click [Yes].
Enrolling a Fingerprint
Enrolling a fingerprint will increase the security of your
system and streamline the authentication procedure.
You enroll fingerprints in the OmniPass Control Center.
With an OmniPass user logged in, double-click the
system tray OmniPass icon. Select the User Settings tab
and click Enrollment under the User Settings area. Click
Enroll Authentication Device and authenticate at the
authentication prompt to start device enrollment.
1. During initial user enrollment, you will be prompted
to select the finger you wish to enroll. Fingers that
have already been enrolled will be marked by a green
check. The finger you select to enroll at this time will
be marked by a red arrow. OmniPass allows you to
re-enroll a finger. If you choose a finger that has
already been enrolled and continue enrollment,
OmniPass will enroll the fingerprint, overwriting the
old fingerprint. Select a finger to enroll and click
[Next].
2. It is now time for OmniPass to capture your selected
fingerprint. It may take a several capture attempts
before OmniPass acquires your fingerprint. Should
OmniPass fail to acquire your fingerprint, or if the
capture screen times out, click [Back] to restart the
fingerprint enrollment process.
Your system has a “swipe” fingerprint sensor. A swipe
sensor is small and resembles a skinny elongated rectangle. To capture a fingerprint, gently swipe or pull
your fingertip over the sensor (starting at the second
knuckle) in the direction of the arrow. Swiping too
fast or too slow will result in a failed capture. The
Choose Finger screen has a [Practice] button; click it
to practice capturing your fingerprint. When you are
comfortable with how your fingerprint is captured,
proceed to enroll a finger.
3. Once OmniPass has successfully acquired the fingerprint, the Verify Fingerprint screen will automatically appear. To verify your enrolled fingerprint, place
your fingertip on the sensor and hold it there as if
you were having a fingerprint captured. Successful
fingerprint verification will show a green fingerprint
in the capture window and the text Verification
Successful under the capture window.
USING OMNIPASS
You are now ready to begin using OmniPass. Used regularly, OmniPass will streamline your authentication
procedures.
Password Replacement
You will often use the password replacement function.
When you go to a restricted access website (e.g., your
bank, your web-based email, online auction or payment
sites), you are always prompted to enter your login
credentials. OmniPass can detect these prompts and you
can teach OmniPass your login credentials. The next time
you go to that website, you can authenticate with your
fingerprint to gain access.
OmniPass Authentication Toolbar
After installing OmniPass and restarting, you will notice
a dialog you have not seen before at Windows Logon.
This is the OmniPass Authentication Toolbar, and it is
displayed whenever the OmniPass authentication system
is invoked. The OmniPass authentication system may be
invoked frequently: during Windows Logon, during
OmniPass Logon, when unlocking your workstation,
when resuming from standby or hibernate, when
unlocking a password-enabled screensaver, during password replacement for remembered site or application
logins, and more. When you see this toolbar, OmniPass is
prompting you to authenticate.
The Logon Authentication window indicates what
OmniPass-restricted function you are attempting. The
icons in the lower left (fingerprint and key) show what
authentication methods are available to you. Selected
authentication methods are highlighted while unselected
methods are not. When you click the icon for an unselected authentication method, the authentication prompt
associated with that method is displayed.
When prompted to authenticate, you must supply the
appropriate credentials: an enrolled finger for the fingerprint capture window or your master password for the
master password prompt (the key icon).
Remembering a Password
OmniPass can remember any application, GUI, or password protected resource that has a password prompt.
69
Osian_UG.book Page 70 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Appendix B
Using the following procedure, you can store a set of
credentials into OmniPass. These credentials will then be
linked to your “master password” or fingerprint.
Go to a site that requires a login (username and password), but do not log in yet. At the site login prompt,
enter your username and password in the prompted
fields, but do not enter the site (do not hit [Enter],
[Submit], [OK], or Login). Right-click the OmniPass
system tray icon and select Remember Password from
the submenu. The Windows arrow cursor will change to
a golden key OmniPass cursor. Click this OmniPass
cursor in the login prompt area, but do not click the
[Login] or [Submit] button.
Associating a Friendly Name
After clicking the OmniPass key cursor near the login
prompt, OmniPass will prompt you to enter a “friendly
name” for this site. You should enter something that
reminds you of the website, the company, or the service
you are logging into. In its secure database, OmniPass
associates this friendly name with this website.
Additional Settings for Remembering a Site
When OmniPass prompts you to enter a “friendly name”
you also have the opportunity to set how OmniPass
authenticates you to this site. There are three effective
settings for how OmniPass handles a remembered site.
The default setting is Automatically click the “OK” or
“Submit” button for this password protected site once
the user is authenticated. With this setting, each time
you navigate to this site OmniPass will prompt you for
your master password or fingerprint authentication
device. Once you have authenticated with OmniPass,
you will automatically be logged into the site.
Less secure is the option to Automatically enter this
password protected site when it is activated. Do not
prompt for authentication. Check the upper box to get
this setting, and each time you navigate to this site
OmniPass will log you into the site without prompting
you to authenticate.
This setting is more convenient in that
whenever you go to a site remembered
with this setting, you will bypass any
authentication procedure and gain instant
access to the site. But should you leave
your system unattended with your
OmniPass user logged in, anyone using
your system can browse to your password
protected sites and gain automatic access.
If you uncheck both boxes in Settings for this Password
Site, OmniPass will prompt you for your master password or fingerprint authentication device. Once you
70
have authenticated with OmniPass your credentials will
be filled in to the site login prompt, but you will have to
click the website [OK], [Submit], or [Login] button to
gain access to the site.
Click Finish to complete the remember password procedure. The site location, the credentials to access the site,
and the OmniPass authentication settings for the site are
now stored in the OmniPass secure database. The
OmniPass authentication settings (Settings for this Password Site) can always be changed in Vault Management.
Logging in to a Remembered Site
Whether or not OmniPass prompts you to authenticate
when you return to a remembered site is determined by
Settings for this Password Site and can be changed in
Vault Management.
The following cases are applicable to using OmniPass to
login to: Windows, remembered websites, and all other
password protected resources.
With Master Password
Once you return to a site you have remembered with
OmniPass, you may be presented with a master password prompt. Enter your master password and you will
be allowed into the site.
Logging into Windows with a Fingerprint Device
When logging into Windows with a fingerprint device,
the fingerprint capture window will now appear next to
the Windows Login screen. Place your enrolled fingertip
on the sensor to authenticate. You will be simultaneously
logged into Windows and OmniPass. The capture
window will also appear if you have used Ctrl-Alt-Del to
lock a system, and the fingerprint device can be used to
log back in as stated above.
If a machine is locked and OmniPass
detects a different user logging back in
with a fingerprint, the first user will be
logged out and the second user logged in.
In Windows XP, your login options must be set either for
classic login, or for fast user switching and logon screen
to be enabled to use your fingerprint to log on to
Windows. To change this go to Control Panel, select
User Accounts and then click Change the way users log
on or off. If your Windows screensaver is password
protected, the fingerprint capture window will now
appear next to screensaver password dialog during
resume. You can authenticate to your screensaver password prompt with your enrolled finger.
Password Management
OmniPass provides an interface that lets you manage
your passwords. To access this GUI, double-click the
Osian_UG.book Page 71 Monday, October 9, 2006 1:24 PM
S e c u r i t y D e v i c e U s e r ’s G u i d e
OmniPass key in the system tray. Click Vault Management; you will be prompted to authenticate. Once you
gain access to Vault Management, click Manage Passwords under Vault Settings. You will see the Manage
Passwords interface, with a list of friendly names.
You can view the credentials stored for any remembered
website by highlighting the desired resource under Password Protected Dialog and clicking Unmask Values.
Should a password be reset, or an account expire, you
can remove stored credentials from OmniPass. Highlight
the desired resource under Password Protected Dialog
and click Delete Page. You will be prompted to confirm
the password deletion.
The two check boxes in Manage Passwords govern
whether OmniPass prompts you to authenticate or
directly logs you into the remembered site.
OmniPass will overwrite an old set of credentials for a
website if you attempt to use Remember Password on an
already remembered site.
The exception to the above rule is the resetting of your
Windows password. If your password is reset in
Windows, then the next time you login to Windows,
OmniPass will detect the password change and prompt
you to “Update” or “Reconfirm” your password with
OmniPass. Enter your new Windows password in the
prompt(s) and click OK and your OmniPass "master
password" will still be your Windows password.
OmniPass User Identities
Identities allow OmniPass users to have multiple
accounts to the same site (e.g., bob@biblomail.com and
boballen@biblomail.com). If OmniPass did not provide
you identities, you would be limited to remembering
one account per site.
To create and manage identities, double-click the
OmniPass key in the system tray. Click Vault Management; OmniPass will prompt you to authenticate. Once
you gain access to Vault Management, click Manage
Identities under Vault Settings. You can only manage
the identities of the currently logged in OmniPass user
To set the default identity, highlight the identity you
want as default and click [Set as Default]; click [Apply]
to ensure the settings are saved. If you log in to
OmniPass with a fingerprint device, you will automatically be logged in to the default identity for that
OmniPass user. You can choose the identity with which
you are logging in if you login using "master password".
Choosing User Identity during Login
To choose your identity during login, type your username in the User Name: field. Press [Tab] and see that
the Domain: field self-populates. Click the Password:
field to bring the cursor to it, and you will see the pulldown menu in the Identity: field. Select the identity you
wish to login as and then click OK to login.
Switch User Identity
To switch identities at any time, right-click the
OmniPass system tray icon and click Switch User Identity from the submenu. The Switch Identity dialog will
appear. Select the desired identity and then click OK.
Identities and Password Management
On the Manage Passwords interface of the Vault
Management tab of the OmniPass Control Center, there
is a pull-down selection box labeled, Identity. This field
lets you choose which identity you are managing passwords for. When you select an identity here, only those
password protected dialogs that are associated with that
identity are shown. You can perform all the functions
explained in “Password Management” on page 70.
CONFIGURING OMNIPASS
This section gives an overview of both the Export/
Import function and the OmniPass Control Center.
Exporting and Importing Users
Using the OmniPass Control Center, you can export and
import users in and out of OmniPass. The export
process backs up all remembered sites, credentials, and
any enrolled fingerprints for an OmniPass user. All
OmniPass data for a user is backed up to a single
encrypted database file. During the import process, the
Windows login of the exported user is required. If the
To add a new identity, click New Identity or double-click
Click here to add a new identity. Name the new identity
and click [OK], then click [Apply]. You can now switch
to the new identity and start remembering passwords.
To delete an identity, highlight the identity you want to
delete and click [Delete Identity], then click [Apply].
When you delete an identity, all of its
associated remembered sites and password
protected dialogs are lost.
71
Osian_UG.book Page 72 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Appendix B
proper credentials cannot be supplied, the user profile
will not be imported.
■
■
You should periodically export your user
profile and store it in a safe place. If
anything happens to your system, you
can import your OmniPass profile to a
new system and have all your remembered settings and fingerprints instantly.
When you examine the importation, you
are prompted for authentication. The
credentials that will allow a user profile
to be imported are the Windows login
credentials of the exported user. They
are the credentials that had to be
submitted when the user profile was
exported. You will need User Name,
Password, and Domain.
Exporting an OmniPass User Profile
To export a user, open the OmniPass Control Center,
and click Import/Export User under Manage Users.
Click Exports an OmniPass user profile. OmniPass will
prompt you to authenticate. Upon successfully authentication, you must name the OmniPass user profile and
decide where to save it. An .opi file is generated, and you
should store a copy of it in a safe place.
This .opi file contains all your user specific OmniPass
data, and it is both encrypted and password protected.
This user profile does NOT contain any of your
encrypted data files.
Importing an OmniPass User Profile
You cannot import a user into OmniPass if
there already is a user with the same name
enrolled in OmniPass.
To import an OmniPass user open the OmniPass
Control Center, and click Import/Export User under
Manage Users. Click Imports a new user into OmniPass
and then select OmniPass Import/Export File (*.opi)
and click Next. OmniPass will then prompt you to
browse for the file you had previously exported (.opi
file). When you select the .opi file for importation,
OmniPass will prompt you for authentication. The
credentials that will allow a user profile to be imported
are the Windows login credentials of the exported user.
They are the credentials that had to be submitted when
the user profile was exported. You will need User Name,
Password, and Domain. If you don’t remember the value
for Domain, in a PC or SOHO environment Domain
should be your computer name.
72
OmniPass will notify you if the user was successfully
imported.
Things to Know Regarding Import/Export
Assume you export a local Windows User profile from
OmniPass. You want to import that profile to another
machine that has OmniPass. Before you can import
the profile, a Windows user with the same login credentials must be created on the machine importing the
profile.
■
Example: I have a Windows user with the username
“Tom” and the password “Sunshine” on my system. I
have enrolled Tom into OmniPass and remembered
passwords. I want to take all my passwords to new system. I export Tom’s OmniPass user profile. I go to my
new system and using the Control Panel I create a user
with the username "Tom" and the password "Sunshine". I can now successfully import the OmniPass
user data to the new system.
■
If you export an OmniPass-only user, you can import
that user to any computer running OmniPass, provided that a user with that name is not already
enrolled in OmniPass.
■
If you attempt to import a user profile who has the
same name as a user already enrolled in OmniPass, the
OmniPass import function will fail.
OMNIPASS CONTROL CENTER
This section will serve to explain functions within the
OmniPass Control Center that weren’t explained earlier.
You can access the OmniPass Control Center any of
three ways:
■
Double-click the golden OmniPass key shaped icon in
the Windows taskbar (typically in the lower-right corner of the desktop)
■
Click the Start button; select the Programs group;
select the Softex program group; and click the
OmniPass Control Center selection.
■
Open the Windows Control Panel (accessible via Start
button --> Settings --> Control Panel) and doubleclick the Softex OmniPass icon.
User Management
The User Management tab has two major interfaces:
Add/Remove User and Import/Export User. Import/
Export User functionality is documented in “Exporting
and Importing Users” on page 71. Add/Remove User
functionality is straightforward.
If you click Adds a new user to OmniPass you will start
the OmniPass Enrollment Wizard. The Enrollment
Wizard is documented in “User Enrollment” on page 68.
Osian_UG.book Page 73 Monday, October 9, 2006 1:24 PM
S e c u r i t y D e v i c e U s e r ’s G u i d e
If you click Removes a user from OmniPass, OmniPass
will prompt you to authenticate. Authenticate with the
credentials (or enrolled fingerprint) of the user you wish
to remove. OmniPass will prompt you to confirm user
removal. Click OK to complete user removal.
Removing a user will automatically destroy
all OmniPass data associated with that
user. All identities and credentials
associated with the user will be lost. If you
are sure about removing the user, we
recommend you export the user profile.
User Settings
The User Settings tab has four interfaces: Audio Settings,
Taskbar Tips, and Enrollment. User settings allow users
to customize OmniPass to suit their individual preferences. Under User Settings (Audio Settings and Taskbar
Tips) you can set how OmniPass notifies the user of
OmniPass events (e.g., successful login, access denied,
etc.). The details of each setting under the Audio
Settings and Taskbar Tips interfaces are self-explanatory.
The Enrollment interface allows you to enroll fingerprints. For the procedure to enroll and authentication
device refer to Chapter 2.3. To enroll additional fingerprints, click Enroll Authentication Device, and authenticate with OmniPass. Select the fingerprint recognition
device in the Select Authentication Device screen (it
should already be marked by a green check if you have a
finger enrolled) and click Next.
System Settings
The OmniPass Startup Options interface can be found
in the System Settings tab. With these options you can
specify how your OmniPass Logon is tied to your
Windows Logon.
The first option, Automatically log on to OmniPass as
the current user, will do just as it says; during Windows
login, you will be logged on to OmniPass using your
Windows login credentials. If the user logging into
Windows was never enrolled into OmniPass, upon login
no one will be logged on to OmniPass. This setting is
appropriate for an office setting or any setting where
users must enter a username and password to log into a
computer. This is the default setting.
With the second option, Manually log on to OmniPass
at startup, OmniPass will prompt you to login once you
have logged on to Windows.
With the third option, Do not log on to OmniPass at
startup, OmniPass will not prompt for a user to be
logged on.
You can manually log on to OmniPass by right-clicking
the OmniPass taskbar icon and clicking Log in User
from the right-click menu.
73
Osian_UG.book Page 74 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Appendix B
TROUBLESHOOTING
You cannot use OmniPass to create Windows users. You
must first create the Windows user, and you will need
administrative privileges to do that. Once the Windows
user is created, you can add that user to OmniPass using
the same username and password
Cannot add Windows users to OmniPass
If you experience difficulties adding a Windows user
to OmniPass, you may need to adjust your local security settings. You can do this by going to Start,
Control Panel, Administrative Tools, and Local
Security Settings. Expand Local Policies, expand
Security Options, and double-click Network Access:
Sharing and Security Model for Local Accounts. The
correct setting should be Classic - Local Users Authenticate as Themselves.
Cannot add a User with a Blank Password to OmniPass
If you experience difficulties adding a user with a
blank password to OmniPass, you may need to adjust
your local security settings. First attempt the procedure explained in the Cannot add Windows user to
OmniPass section. If the difficulties persist, then try
the following procedure.
Click Start, Control Panel, Administrative Tools,
and Local Security Settings. Expand Local Policies,
expand Security Options, and double-click
Accounts: Limit local account use of blank passwords to console login only. This setting should be
set to Disabled.
74
Dialog appears after OmniPass authentication during
Windows Logon
After installing OmniPass on your system, you can
choose to logon to Windows using OmniPass. You
authenticate with OmniPass (via master password, or
an enrolled security device) and OmniPass logs you
into Windows. You may, during this OmniPass
authentication, see a Login Error dialog box.
This dialog box occurs when OmniPass was unable to
log you into Windows with the credentials supplied
(username and password). This could happen for any
of the following reasons:
■
■
Your Windows password has changed
Your Windows account has been disabled
If you are having difficulties due to the first reason,
you will need to update OmniPass with your changed
Windows account password. Click Update Password
and you will be prompted with a dialog to reconfirm
your password.
Enter the new password to your Windows user
account and click OK. If the error persists, then it is
unlikely the problem is due to your Windows user
account password changing.
Osian_UG.book Page 75 Monday, October 9, 2006 1:24 PM
S e c u r i t y D e v i c e U s e r ’s G u i d e
Trusted Platform Module Installation
This disc contains several utilities that allow you to
enhance the security of your system using the optional
Trusted Platform Module (TPM) contained in the system. TPM is a Trusted Computing Group (TCG)-compliant embedded security chip that allows computers to
run applications more securely and to make transactions
and communications more trustworthy. TPM is an
important component of the Fujitsu Security Platform.
• The use of this disc requires that you
have a device capable of reading CDs
attached to your system. If you do not
have a built-in CD or DVD player, you
will need to attach an external player.
• The use of this disc also requires a
device capable of writing to removable
media (such as a floppy disk drive, CDRW drive, or PCMCIA memory card).
This drive will be used to store the
Emergency Recovery Token file and -- if
desired -- the Emergency Recovery
Archive file. For more information on
available external devices, visit our
website at: us.fujitsu.com/computers.
3.
4.
5.
6.
Installing the TPM Applications
1. Insert the “Trusted Platform Module Drivers and
Applications CD” in the drive.
2.
3.
4.
5.
When installing the software, be sure to
create Emergency Recovery Archive and
Emergency Recovery Token files when
prompted by the Security Platform
Initialization Wizard. These files will be
necessary in the event of hardware failure.
Failure to create these files could result in
a loss of the Security Platform owner key,
which is the physical root for secrets as
well as the logical root for all Security
Platform user-specific keys. The
Initialization Wizard provides step-by-step
instructions for creating the files.
Open the Security menu, scroll down to Set Supervisor Password, and enter a password (if not already
set).
While in the Security menu, scroll down to Security
Chip Setting, and click on it. The Security Chip Setting submenu will appear.
Click on Security Chip to enable it.
Click [F10] to save changes and exit.
The setup program should start the installation
automatically. If the installation does not start automatically, go to the setup.exe file on the disc and
double-click on it.
Follow the instructions that appear on your screen
to load the drivers and applications for TPM.
After loading the software, you will be prompted to
reboot your system. Remove the CD from the drive,
then reboot.
After rebooting, the Security Platform Installation
Wizard will open and lead you through the setup
and customization of the TPM applications.
Getting Help
For detailed help about installing the TPM applications, go to the readme.txt file on the disc.
■
■
For in-depth help and information about the TPM
applications, double-click on the Security Platform
icon in the system tray, and click {Getting Started
Guide].
Procedure
Be sure you have a built-in or external drive attached to
your system that can read CDs. You will also need a
means to write to removable media during the installation.
Enabling the Security Chip in BIOS
1. Before installing the TPM software, you will need to
enable the security chip in the system BIOS. To do so:
• If your system is running, click [Start] -> Shut
Down, and select Restart. Click [OK].
• If the system is not running, power it up.
2. When the Fujitsu logo appears, press the [F2] button. The BIOS Setup Utility will appear.
75
Osian_UG.book Page 76 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC User’s Guide – Appendix B
76
Osian_UG.book Page 77 Monday, October 9, 2006 1:24 PM
Index
Index
A
charging the battery pack . . . . . . . . . . . . . . . . . . . . . . .26
adjusting the display brightness . . . . . . . . . . . . . . . . . 24
cleaning the display screen . . . . . . . . . . . . . . . . . . . . . .35
air flow vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
configuring peripherals interface . . . . . . . . . . . . . . . .36
application buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
application A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
application B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Ctl-Alt-Del button . . . . . . . . . . . . . . . . . . . . . . . . . . 9
display mode button . . . . . . . . . . . . . . . . . . . . . . . . . 9
EMail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
enter button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
escape button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Fujitsu Menu Utility . . . . . . . . . . . . . . . . . . . . . . . . 10
function button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
orientation button . . . . . . . . . . . . . . . . . . . . . . . . . . 9
security button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
tertiary functions . . . . . . . . . . . . . . . . . . . . . . . . 12, 13
connectors and peripheral interfaces . . . . . . . . . . . . .16
Automatically Downloading Driver Updates . . . . . . 37
conserving battery power . . . . . . . . . . . . . . . . . . . . . . .27
conventions used in the guide . . . . . . . . . . . . . . . . . . vii
critically low battery level . . . . . . . . . . . . . . . . . . . . . . .23
cursor
not tracking pen . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
D
DC input connector . . . . . . . . . . . . . . . . . . . . . . . . .5, 16
DIMM card, removing . . . . . . . . . . . . . . . . . . . . . . . . .29
display
screen is blank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
screen, cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
B
Drivers and Application Restore CD . . . . . . . . . . . . .36
battery gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
E
battery gauge icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
external monitor connector . . . . . . . . . . . . . . . . . . . . . .5
battery icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
battery pack
charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
critically low level . . . . . . . . . . . . . . . . . . . . . . . . . . 23
low-battery warning . . . . . . . . . . . . . . . . . . . . . . . . 23
no memory effect . . . . . . . . . . . . . . . . . . . . . . . . . . 26
overcharge protection . . . . . . . . . . . . . . . . . . . . . . . 26
removing and installing . . . . . . . . . . . . . . . . . . 26, 27
will not begin charging . . . . . . . . . . . . . . . . . . . . . . 26
battery power
conserving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
used in Standby mode . . . . . . . . . . . . . . . . . . . . . . 23
F
FDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
fingerprint sensor device . . . . . . . . . . . . . . . . . . . . .2, 67
enrolling a fingerprint . . . . . . . . . . . . . . . . . . . . . . .69
importing an OmniPass user profile . . . . . . . . . . . .72
installing OmniPass . . . . . . . . . . . . . . . . . . . . . . . . .67
introducing the fingerprint sensor device . . . . . . .67
using OmniPass . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
verifying information about OmniPass . . . . . . . . .68
Fujitsu contact information . . . . . . . . . . . . . . . . . . . . vii
battery release latch . . . . . . . . . . . . . . . . . . . . . . . . . 3, 17
Fujitsu Driver Update utility . . . . . . . . . . . . . . . . . . . .37
BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
application buttons, for . . . . . . . . . . . . . . . . . . 12, 13
Fujitsu online . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
BOOT Priority Change . . . . . . . . . . . . . . . . . . . . . . . . 36
H
bridge battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
hard disk drive access icon . . . . . . . . . . . . . . . . . . . . . . .8
built-in microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
headphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
headphone jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
C
Hibernate (Save-to-Disk) mode . . . . . . . . . . . . . .22, 23
calibrating the pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Hibernate mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
care and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 33
charge/DC input icon . . . . . . . . . . . . . . . . . . . . . . . . . . 7
I
idle state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
77
Osian_UG.book Page 78 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC
IEEE 1394 jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5, 17
PC card slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4, 16, 28
infrared data transfer not working . . . . . . . . . . . . . . 35
PC Cards
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
infrared keyboard port . . . . . . . . . . . . . . . . . . . . . . . 2, 6
interfaces
connectors and peripherals . . . . . . . . . . . . . . . . . . 16
pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4, 6
installing a pen tether . . . . . . . . . . . . . . . . . . . . . . . .25
not responding . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
replacing the tip . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
IrDA port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
pen tether . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
IrDA/FIR port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
pen tether point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
infrared keyboard/mouse port . . . . . . . . . . . . . . . . . . 16
Installing a Memory Stick . . . . . . . . . . . . . . . . . . . . . . 28
peripheral connectors . . . . . . . . . . . . . . . . . . . . . . . . . .16
L
LAN jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Local Area Network (LAN) . . . . . . . . . . . . . . . . . . . . 17
Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5, 17
low-battery warning . . . . . . . . . . . . . . . . . . . . . . . . . . 23
power on/suspend/resume
button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
power usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
powering up the pen tablet . . . . . . . . . . . . . . . . . . . . .22
M
memory cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
memory module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Memory Stick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
microphone jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
preparation for wireless LAN connection . . . . . . . . . .51
problems, solving . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
protecting the display screen . . . . . . . . . . . . . . . . . . . .33
R
removable battery pack . . . . . . . . . . . . . . . . . . . . . . . . .3
removing a DIMM card . . . . . . . . . . . . . . . . . . . . . . . .29
removing a Memory Stick . . . . . . . . . . . . . . . . . . . . . .28
restoring the factory image . . . . . . . . . . . . . . . . . . . . .36
restoring your pre-installed software . . . . . . . . . . . . .36
N
navigation buttons . . . . . . . . . . . . . . . . . . . . . . . . . 2, 11
O
Off state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21, 22
OmniPass
Control Center . . . . . . . . . . . . . . . . . . . . . . . . . . . .
importing an OmniPass user profile . . . . . . . . . . .
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
verifying information . . . . . . . . . . . . . . . . . . . . . . .
power icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7, 21
blinking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21, 22
not displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
72
72
67
69
68
optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
resuming system operation . . . . . . . . . . . . . . . . . .23, 35
RJ-45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
S
SD Card
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
SD Card slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
SD Card/Memory Stick Slot . . . . . . . . . . . . . . . . . . . . .4
Secure Digital Card
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
P
Security Application Panel
operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
uninstalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
page up/page down . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Setting up Security Panel . . . . . . . . . . . . . . . . . . . . . . .13
PC Card eject button . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Shock Sensor Utility . . . . . . . . . . . . . . . . . . . . . . . . . . .23
overheating, avoiding . . . . . . . . . . . . . . . . . . . . . . . . . 34
78
Osian_UG.book Page 79 Monday, October 9, 2006 1:24 PM
Index
shutting down the system . . . . . . . . . . . . . . . . . . . . . . 22
solving problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Trusted Platform Module
enabling the security chip in BIOS . . . . . . . . . . . . .75
getting help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
turning off the system . . . . . . . . . . . . . . . . . . . . . . . . . .22
Smart Card slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
speaker/headphone volume too low . . . . . . . . . . . . . 35
status display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
battery icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
charge/DC input icon . . . . . . . . . . . . . . . . . . . . . . . . 7
hard disk drive access icon . . . . . . . . . . . . . . . . . . . . 8
power icon, blinking . . . . . . . . . . . . . . . . . . . . . . . . 21
power icon, system states indicated by . . . . . . . 7, 21
U
Universal Serial Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
USB ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5, 16
using the pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
storing the system unit . . . . . . . . . . . . . . . . . . . . . . . . 34
W
Stylistic ST5000
care and maintenance . . . . . . . . . . . . . . . . . . . . . . . 33
features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2, 3, 4, 5, 6
items included with . . . . . . . . . . . . . . . . . . . . . . . . . . 1
storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Windows XP Tablet PC Edition . . . . . . . . . . . . . . vii, 1
Stylistic ST5000 specifications
additional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
agency approval . . . . . . . . . . . . . . . . . . . . . . . . . . . .
display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
42
42
41
42
41
41
42
41
Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Ad Hoc Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
connecting the WLAN . . . . . . . . . . . . . . . . . . . . . . .51
for better communications . . . . . . . . . . . . . . . . . . .49
Infrastructure Mode . . . . . . . . . . . . . . . . . . . . . . . . .49
IP address information . . . . . . . . . . . . . . . . . . . . . . .62
Other settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
setting of power-saving function . . . . . . . . . . . . . . .57
specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
starting transmission . . . . . . . . . . . . . . . . . . . . . . . .50
stopping transmission . . . . . . . . . . . . . . . . . . . . . . .49
troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Wireless LAN glossary . . . . . . . . . . . . . . . . . . . . . . .60
Suspend/Resume
disabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
before using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Suspend/Resume button . . . . . . . . . . . . . . . . . . . . . . . 17
wireless LAN/Bluetooth on/off switch . . . . . . . . . .3, 17
suspend mode, determining . . . . . . . . . . . . . . . . . . . . 22
suspending system operation . . . . . . . . . . . . . . . . . . . 22
Suspend-to-RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22, 23
system interface connector . . . . . . . . . . . . . . . . . . . . . . 3
system states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Idle state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Off state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
On state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Suspend-to-RAM . . . . . . . . . . . . . . . . . . . . . . . . . .
21
21
21
21
21
system status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
system will not resume operation . . . . . . . . . . . . . . . 35
T
Tablet Dock latch point . . . . . . . . . . . . . . . . . . . . . . . . 3
Tablet Dock port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
tertiary functions of application buttons . . . . . . 12, 13
thermal suede . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
79
Osian_UG.book Page 80 Monday, October 9, 2006 1:24 PM
Stylistic ST5100 Series Tablet PC
80
Osian_UG.book Page 81 Monday, October 9, 2006 1:24 PM
Osian_UG.book Page 82 Monday, October 9, 2006 1:24 PM
Osian_UG.book Page 83 Monday, October 9, 2006 1:24 PM
Osian_UG.book Page 84 Monday, October 9, 2006 1:24 PM