Fujitsu M3097E Photo Scanner User Manual

Owner’s Manual
GMR 21/41
marine radar
© 2006 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151st Street,
Olathe, Kansas 66062, USA
Tel. (913) 397.8200 or (800) 800.1020
Fax (913) 397.8282
Garmin (Europe) Ltd.
Unit 5, The Quadrangle,
Abbey Park Industrial Estate,
Romsey, SO51 9DL, UK
Tel.+44 (0) 870.8501241 (outside the UK)
0808 2380000 (within the UK)
Fax+44 (0) 870.8501251
Garmin Corporation
No. 68, Jangshu 2nd Road,
Shijr, Taipei County, Taiwan
Tel. 886/2.2642.9199
Fax 886/2.2642.9099
All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any
storage medium, for any purpose without the express prior written consent of Garmin. Garmin hereby grants permission to download a single copy of this manual onto
a hard drive or other electronic storage medium to be viewed and to print one copy of this manual or of any revision hereto, provided that such electronic or printed
copy of this manual must contain the complete text of this copyright notice and provided further that any unauthorized commercial distribution of this manual or any
revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Garmin reserves the right to change or improve its products and to make changes in the content
without obligation to notify any person or organization of such changes or improvements. Visit the Garmin Web site (www.garmin.com) for current updates and
supplemental information concerning the use and operation of this and other Garmin products.
Garmin®, GPSMAP®, AutoLocate®, TracBack®, BlueChart®, and MapSource® are registered trademarks of Garmin Ltd. or its subsidiaries and may not be used without
the express permission of Garmin.
December 2006
Part Number 190-00665-00 Rev. B
Printed in Taiwan
Introduction > Installing Your GMR 21/41 and About This Manual
Introduction
This manual covers the features and operation of the GMR 21/41
marine radar when viewed on a Garmin marine network chartplotter.
Installing Your GMR 21/41
To install your GMR 21/41, refer to the GMR 21/41 Installation
Instructions included in this box. If you experience difficulty
installing the radar, contact Garmin Product Support or an installation
professional in your area.
About This Manual
To get the most out of your GMR 21/41, take time to read this manual
and learn the operating procedures in detail. This manual is organized
into the following sections.
The Appendix contains specifications, regulatory information, and
maintenance information. You can also find warranty, European
Licensing Requirements, and FCC information in the Appendix.
An Index is provided at the end of the manual for reference.
Manual Conventions
This manual uses the term Warning to indicate a potentially
hazardous situation, which, if not avoided, could result in
death or serious injury.
This manual uses the term Caution to indicate a potentially
hazardous situation, which, if not avoided, may result
in minor injury or property damage. It may also be used
without the symbol to alert you to avoid unsafe practices.
The Introduction sections contains the Table of Contents, Product
Registration, and Software License Agreement.
The Basic Operation section describes the features and operation of
the GMR 21/41.
GMR 21/41 Owner’s Manual
Introduction > Table of Contents
Table of Contents
Introduction............................................................................i
Installing Your GMR 21/41........................................................ i
About This Manual.................................................................... i
Manual Conventions......................................................................... i
Product Registration............................................................... iii
Contact Garmin...............................................................................iii
Software License Agreement................................................. iii
Warning.................................................................................... iv
Important Information............................................................. iv
Appendix.............................................................................14
Specifications......................................................................... 14
European License Requirements......................................... 15
Declaration of Conformity (DoC).......................................... 15
Limited Warranty.................................................................... 16
FCC Compliance..................................................................... 17
Industry Canada Compliance................................................ 17
Index....................................................................................18
Basic Operation....................................................................1
Understanding Radar............................................................... 1
Understanding the Radar Display.................................................... 2
Radar Page................................................................................ 3
Configuring the Radar Page............................................................. 3
Using the Radar Adjustment Menu................................................. 4
Map Page Radar Overlay......................................................... 9
Radar Tab................................................................................ 10
General Sub Tab............................................................................ 10
Display Sub Tab............................................................................. 11
MARPA Sub Tab........................................................................... 12
Advanced Sub Tab......................................................................... 13
ii
GMR 21/41 Owner’s Manual
Introduction > Product Registration and Software License Agreement
Product Registration
Software License Agreement
Use this area to record the serial number (8-digit number located
on the bottom of the GMR 21/41) in case your GMR 21/41 needs
service. Keep the original sales receipt, or a photocopy, in a safe
place.
Garmin grants you a limited license to use the software embedded in
this device (the “Software”) in binary executable form in the normal
operation of the product. Title, ownership rights, and intellectual
property rights in and to the Software remain in Garmin.
Help us better support you by completing our online registration
today! Connect to our Web site at www.garmin.com/registration/.
Serial Number: ___ ___ ___ ___ ___ ___ ___ __
Contact Garmin
Contact Garmin if you have any questions while using your
GMR 21/41. In the USA contact Garmin Product Support by phone:
(913) 397-8200 or (800) 800-1020, Monday–Friday, 8 AM–5 PM
Central Time; or go to www.garmin.com/support/, and click
Product Support.
In Europe, contact Garmin (Europe) Ltd. at +44 (0) 870.8501241
(outside the UK) or 0808 2380000 (within the UK).
BY USING THE GMR 21/41, YOU AGREE TO BE BOUND BY THE
TERMS AND CONDITIONS OF THE FOLLOWING SOFTWARE LICENSE
AGREEMENT. PLEASE READ THIS AGREEMENT CAREFULLY.
You acknowledge that the Software is the property of Garmin and
is protected under the United States of America copyright laws and
international copyright treaties. You further acknowledge that the
structure, organization, and code of the Software are valuable trade
secrets of Garmin and that the Software in source code form remains
a valuable trade secret of Garmin. You agree not to decompile,
disassemble, modify, reverse assemble, reverse engineer, or reduce
to human readable form the Software or any part thereof or create
any derivative works based on the Software. You agree not to export
or re-export the Software to any country in violation of the export
control laws of the United States of America.
GMR 21/41 Owner’s Manualiii
Introduction > Warning and Important Information
Warning
Failure to avoid the following potentially hazardous situations could
result in an accident or collision resulting in death or serious injury.
The radar scanner transmits electromagnetic energy. Ensure that the scanner
has been installed according to the recommendations given in this guide, and
that all personnel are clear of the scanner before switching to Transmit mode.
For protection from lightning, this installation must conform to NFPA code,
section 302. The installation of a lightning protective mast is recommended,
and the scanner must be connected to water ground using an 8 gauge copper
cable.
WARNING: This product, its packaging, and its components contain chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
This Notice is provided in accordance with California’s Proposition 65. See www.garmin.com/prop65 for more information.
Important Information
MAP DATA INFORMATION: One of the goals of Garmin is to provide customers with the most complete and accurate cartography that is available to us at a
reasonable cost. We use a combination of governmental and private data sources, which we identify in product literature and copyright messages displayed to the
consumer. Virtually all data sources contain some inaccurate or incomplete data. In some countries, complete and accurate map information is either not available or is
prohibitively expensive.
The California Electronic Waste Recycling Act of 2003 requires the recycling of certain electronics. For more information on the applicability to this product, see
www.erecycle.org.
iv
GMR 21/41 Owner’s Manual
Basic Operation > Understanding Radar
Basic Operation
This section covers the features and operation of the GMR 21/41.
Understanding Radar
The GMR 21/41 transmits a narrow beam of microwave energy
in a rotating 360° pattern. When the transmitted energy contacts a
target, some of that energy is reflected and returned to the scanner.
The scanner collects the returned energy for processing and display.
Your GMR 21/41 is operated and adjusted using controls on your
Garmin Marine Network chartplotter. You can view radar data on the
Radar Page or as an overlay on the Map Page. All radar controls are
accessible from both pages.
Caution: The GMR 21/41 transmits microwave energy that
has the potential to be harmful to humans and animals. Before
beginning radar transmission, verify that the area around the radar
is clear. The radar transmits a beam approximately 12° above and
below a line extending horizontally from the center of the scanner.
Avoid looking directly at the scanner, because the eyes are the
most susceptible part of the body.
When the area surrounding the scanner is clear, press and hold
FCTN. The message “Do you want to begin radar transmission?” is
shown. Select Yes, and then press ENTER.
When you turn on the radar, the status bar shows the message “Radar
Warming Up” with a countdown to Standby Mode. The countdown
also appears in the middle of the Radar Page. When the countdown
reaches 0 (zero), the “Hold FCTN to transmit” message appears.
As a safety feature, the radar enters Standby Mode after it warms
up. This gives the operator an opportunity to verify that the area
around the scanner is clear before beginning radar transmission. It is
important to remember that the microwave energy transmitted by the
scanner can potentially be dangerous.
GMR 21/41 Owner’s Manual
Basic Operation > Understanding Radar
Before transmission begins, the message “Spinning Up” is shown
while the radar antenna reaches nominal rotation speed. After the
message disappears, the radar begins painting an image.
Understanding the Radar Display
The Radar Page shows a status bar along the top, user-configurable
digital navigation data down the right side, a Heading Line, and
Range Rings. Soft keys that allow quick access to radar functions and
setting changes appear along the bottom of the page.
Heading Line
Using Range Rings
Use the Range Rings to quickly determine the distance to a target.
The lower-right corner of the screen contains two scales. The scale
value represents the distance from the center of the radar display to
the outermost complete ring. The top scale represents this value. The
bottom scale represents the ring separation or the distance between
the Range Rings. Use the RANGE keys to zoom in or out. The tick
marks on the Range Rings are arranged with major tick marks at 30
degree increments and minor tick marks every five degrees. The tick
marks can help in quickly determining the azimuth to a target.
3/4 nm
Range
Rings
1/2 nm
Soft
keys
1/4 nm
Zoom scale
Ring separation
Heading Line
The Heading Line is shown from your current position along the path
of your current heading.
GMR 21/41 Owner’s Manual
Basic Operation > Radar Page
Radar Page
With the radar properly installed, when you turn on your Garmin
Marine Network chartplotter, it should detect the radar as a new
network connection.
Note: A software update may be needed for the radar to
function properly. If the message “Incompatible Software
Version” appears when you turn on your chartplotter, you must
update your chartplotter software. A software update card is
provided with the GMR 21/41.
When the new radar is detected, the Radar Page is added to the page
sequence. If the Radar Page is not available, press and hold
ADJ/MENU to open the Main Menu. Highlight the System tab, and
select Radar from the Services list at the bottom of the General sub
tab.
To view the Radar Page:
Press PAGE repeatedly until the Radar Page appears.
Radar Page
Configuring the Radar Page
You can customize the appearance of the Radar Page.
note: For detailed information about configuring Digital 1 and
Digital 2 data fields, see your chartplotter owner’s manual.
To add or remove functions on the Radar Page:
1. Open the Radar Page, and then press and hold the DATA/CNFG key to open the Configuration window.
GMR 21/41 Owner’s Manual
Basic Operation > Radar Page
2. Using the ROCKER, highlight the function you want to add or
remove, and press ENTER. Only functions with a check mark
in the check box next to them appear on the Radar Page.
Using the Radar Adjustment Menu
Use the Radar adjustment menu to access the settings and features
most commonly used on the Radar Page including: Gain, Sea Clutter,
Rain Clutter, FTC, Zoom, Target Expansion, Trails, Guard Zone,
VRM/EBL, MARPA, and Hide/Show Navigation Features.
To select an adjustment option from the Radar Page
2. Press up or down on the ROCKER to highlight the option you
want to change, and then press ENTER.
To change a Radar adjustment menu setting:
1. Select an adjustment menu option using the method described
previously.
2. Press up or down on the ROCKER to change the setting,
range, or percentage.
3. Press ENTER to accept the change, or press QUIT to close
the Radar adjustment menu.
1. Press ADJ/MENU to open the Radar adjustment menu.
GMR 21/41 Owner’s Manual
Basic Operation > Radar Page
Gain
Gain controls the sensitivity of the Radar receiver. Auto (default) is
the recommended setting. It automatically adjusts the gain for each
range scale to provide optimal performance. You can also set gain
manually. To see more detail, increase the receiver sensitivity by
selecting a higher gain. If there is too much detail, or the screen is
cluttered, lower the sensitivity (lower the gain) to increase the clarity
of the screen.
appears. To view different areas at the selected zoom range, open the
Radar adjustment menu, highlight Zoom, and press the Move soft
key. Use the ROCKER to move the selection box. Zoom has four
settings: Off, 2x, 4x, and Move.
Sea Clutter
Sea Clutter controls unwanted screen clutter caused by choppy sea
conditions. The slider has three preset positions: Calm, Moderate,
and Rough.
Rain Clutter
Rain Clutter controls unwanted screen clutter caused by rain at close
ranges (use the slider to select 1-100%).
FTC (Fast Time Constant)
FTC controls unwanted screen clutter caused by rain at a distance.
The Fast Time Constant settings are: Off, Low, Medium, and High.
Zoom
Zoom allows you to zoom in on a selected area of the radar screen.
When you select a zoom range, a window showing a zoomed portion
of the screen appears in the lower-left corner and a selection box
GMR 21/41 Owner’s Manual
Zoom view
Selection box
Target Expansion
Use Target Expansion to increase the size of targets. Select On or
Off.
NOTE: The Target Expansion setting has no effect at range scales
of 4 nm or greater.
Basic Operation > Radar Page
Guard Zone
A Guard Zone is a user-defined area of protection. If a target enters
the Guard Zone, an alarm sounds. You can define two Guard Zones.
The Guard Zone Menu has two areas, “Guard Zone 1” and “Guard
Zone 2.” Each area has two settings, Show (Hide) and Adjust.
Target Expansion Off
Target Expansion On
Trails
Trails allows you to select whether all returns on the screen leave a
history trail, and allows you to determine the length of the history
trail (Off, Short, Medium, or Long).
Guard Zone
Trails On
Trails Off
To Define a Guard Zone:
1. Highlight Show Guard Zone 1 or 2, and press ENTER.
2. Highlight Adjust, and press ENTER.
GMR 21/41 Owner’s Manual
Basic Operation > Radar Page
3. Using the ROCKER, define the area on the Radar Page by
adjusting three points: Corner 1, Corner 2, and Circular.
4. Press ENTER to set the Guard Zone.
VRM/EBL
The Variable Range Marker (VRM) and Electronic Bearing Line
(EBL) tools measure range and bearing to a target. You can move
the center point of the VRM, which allows you to measure from one
target to another. Two VRM/EBL tools can be activated at the same
time.
The VRM/EBL option has two tools, VRM/EBL 1 and VRM/EBL 2.
EachVRM/EBL tool has two settings, Show (Hide) and Adjust.
To enable VRM/EBL 1 or VRM/EBL 2:
On the Radar adjustment menu, highlight Show VRM/EBL 1
or VRM/EBL 2, and then press ENTER.
You can adjust the diameter of the VRM and the angle of the EBL.
To adjust the VRM/EBL:
1. Highlight Adjust, and press ENTER.
2. Press right or left on the ROCKER to rotate the EBL around
the center point of the VRM.
3. Press up or down on the ROCKER to increase or decrease
the size of the VMR.
4. Press ENTER to accept the changes.
To move the center location of the VRM:
1. Highlight Move, and press ENTER.
2. Using the ROCKER, move the center point of the VRM to the
selected location.
3. Press ENTER to set the new location.
To use the VRM/EBL, expand the diameter of the VRM so that the
outer edge touches the target. Rotate the EBL until it intersects the
VRM at the target location. The measured range and bearing are
shown in the lower-left corner of the screen.
Variable Range Marker (VRM)
GMR 21/41 Owner’s Manual
Electronic Bearing Line (EBL)
Basic Operation > Radar Page
MARPA
The Mini Automatic Radar Plotting Aid (MARPA) function helps
with collision avoidance. MARPA can track up to 10 designated
targets. Detailed information including bearing, range, course, speed,
closest point of approach (CPA), and time to closest point of approach
(TCPA) for each target is shown in the MARPA list.
Note: MARPA requires the use of a Heading Sensor. The
heading sensor must output the NMEA sentence HDM or HDG
at format 0183, v2.30 or higher. The Gamin Marine Network was
tested using the KVH® 1000 heading sensor using six second
dampening.
MARPA relies on a Heading Sensor to provide accurate own vessel
heading information. Accurate heading data enhances MARPA’s
performance. Each target being tracked by MARPA is represented by
a symbol. The symbols indicate the current state of the target.
Acquiring target
Target is safe
Target is dangerous
For each target, a number and Vector Line is shown with the symbol.
The number is the MARPA list ID number. The Vector Line is a
visual reference of the target’s course and speed.
To designate a MARPA target:
1. Use the ROCKER to move the pointer to the target location.
2. Press the Acquire Target soft key.
When acquiring a target, a red box appears around the target. When
MARPA begins tracking the target, the box is replaced with the
appropriate symbol.
Safe
targets
Acquiring
target
Dangerous
target
Lost target
GMR 21/41 Owner’s Manual
Basic Operation > Map Page Radar Overlay
To view the MARPA List:
Press the MARPA List soft key.
Map Page Radar Overlay
Radar information can be shown as an overlay on the Map Page.
When you overlay radar information on the Map Page, press
ADJ/MENU to access radar options.
Note: Changing the map scale does not change the radar range.
When you zoom in or our on the Map Page, the radar overlay is
scaled to fit.
Enter Standby (Begin Transmitting)
The Enter Standby (Begin Transmitting) option allows you to
select whether the radar is in Standby Mode or is transmitting.
Select Enter Standby to place the radar into Standby Mode. While
in Standby Mode, the radar does not transmit, but power remains
applied to the Magnetron. Select Begin Transmitting to remove the
radar from Standby Mode. After the radar completes “Spinning Up,”
the radar begins transmitting.
Map Page with Radar Overlay and Radar Page
To overlay radar data on the Map Page:
GMR 21/41 Owner’s Manual
1. On the Map Page, press the Show Radar soft key.
2. To hide the radar overlay, press the Radar Options soft key,
and then press the Hide Radar soft key.
Basic Operation > Radar Tab
Radar Tab
When GMR 21/41 is connected to a Garmin Marine Network
chartplotter, and either the Auto-Detect Services or Radar check
box is selected on the System tab, the Radar tab appears on the Main
Menu.
To access and change a setting on the Radar tab:
1. Press the Setup soft key on the Radar Page to open the Main
Menu. The Radar tab is automatically selected.
2. Highlight the setting you want to change, and then press
ENTER.
3. Press QUIT to return to the Radar Page.
10
General Sub Tab
Use the General sub tab to select orientation, timed transmit, and
cross-talk rejection. The available General sub tab options are:
• Orientation—sets the orientation of the Radar Page display.
The settings are Heading Up, North Up, or Course Up.
• North Indicator—toggles the north indicator arrow on or off.
• Timed Transmit—used to save power, usually while at anchor.
When Timed Transmit is On, the radar uses the settings in
Timed Transmit XMIT Time and Timed Transmit STBY
Time fields. When set to Off, these fields are unavailable.
• Timed Transmit XMIT Time—sets the amount of time (in
minutes) for which the radar transmits. If set to 01 min, the
radar transmits for one minute before switching to standby
for the amount of time entered in the Timed Transmit STBY
Time field.
• Timed Transmit STBY Time—sets the amount of time (in
minutes) that the radar is in Standby Mode. If set to 10 min,
the radar is in Standby Mode for 10 minutes before switching
to transmission for the amount of time entered in the Timed
Transmit XMIT Time field. When the radar is in Standby
Mode, the scanner does not rotate or transmit; however, power
is still applied to the Magnetron, eliminating the need for a
warm-up cycle.
GMR 21/41 Owner’s Manual
Basic Operation > Radar Tab
• Cross-talk Rejection—toggles cross-talk rejection on or off.
Radar cross-talk may occur when two or more radar equipped
vessels are operating in proximity to one another. Cross-talk
rejection automatically filters out the cross-talk interference.
Display Sub Tab
Use the Display sub tab to adjust settings for: Center Offset, Rings,
Background color, Heading Line, Bearing Reference, and Navigation
Features. The available Display sub tab options are:
• Center Offset—sets your location on the screen. Center
places your current location in the center of the screen. Look
Ahead shifts your current location toward the bottom of the
screen, allowing you to view an area farther ahead. Auto Shift
adjusts your location on the screen according to the current
speed.
• Rings—toggles the radar rings on or off.
• Background—sets the background color for the Radar Page.
Available options are Black, Blue, or White.
• Heading Line—toggles the Heading Line on or off.
• Bearing Reference—sets your bearing, either Absolute or
Relative. Relative calculates the bearing relative to your
vessel's heading. Absolute calculates the bearing relative to
North.
GMR 21/41 Owner’s Manual
• Navigation Features—allows you to show or hide
navigational features on the Radar Page. Use the ROCKER
and the ENTER key to select or clear options.
• Waypoints—show user waypoints on the Radar Page.
•Bearing Line—show a bearing line on the Radar Page. The
bearing line appears as a line from your current position to
the active destination waypoint.
• Course Line—show a course line from your starting point to the active destination waypoint, which is similar to navigation on a map.
11
Basic Operation > Radar Tab
MARPA Sub Tab
The MARPA sub tab contains settings for Vector Length, Target
History, Own Vessel Safe Zone, Tine To Safe Zone, Safe Ring Zone,
and Velocity Reference.
The available MARPA sub tab options are:
• Vector Length­—predicts the target’s approximate position at
a set time interval. This setting determines the length of the
Vector Line, based on the time interval setting and the target’s
speed. The time interval settings range from .05 minutes to 60
minutes.
• Target History—is a trail showing a target’s movement. Target
History can be turned On or Off.
12
• Own Vessel Safe Zone—is a circular area defined by a range
setting that is centered on your own vessel. If a target enters the
defined area an alarm is sounded. The Safe Zone can be set to a
distance between .01 and 2 nautical miles.
• Time To Safe Zone—sounds an alarm if MARPA determines
that a target will intersect the Own Vessel Safe Zone within the
defined time interval. The time interval settings range from 3 to
24 minutes.
• Safe Zone Ring—displays a ring on the Radar Page depicting
the Own Vessel Safe Zone.
• Velocity Reference—has two settings, Absolute and Relative.
This setting determines how speed and direction are shown on
the MARPA list. Relative calculates target speed and direction
relative to your own. Absolute shows the target’s actual speed.
GMR 21/41 Owner’s Manual
Basic Operation > Radar Tab
Advanced Sub Tab
Use the Advanced sub tab to set the AFC Mode and the front of boat
offset.
To manually adjust the scanner frequency:
1. Highlight the AFC Mode field, and press ENTER.
2. Select Manual, and press ENTER.
3. Highlight the Freq button to the right of the AFC Mode field,
and press ENTER.
NOTE: The Freq button is available only available if Manual is
selected in the AFC Mode field.
4. Press up or down on the ROCKER to adjust the scanner
frequency.
5. Press ENTER to accept the frequency change.
The available Advanced sub tab settings are:
• AFC Mode—sets how the scanner frequency is adjusted.
Select Auto to automatically adjust the scanner frequency for
optimal performance (recommended). Select Manual to set the
frequency manually.
GMR 21/41 Owner’s Manual
Note: The Signal Strength bar graph is damped and may be
slow when responding to frequency tuning changes.
• Signal Strength—Shows the strength of the radar signal.
• Front of Boat Offset—allows you to offset the front of the
boat if you mount the radar at an angle.
13
Appendix > Specifications
Appendix
Specifications
Unit Dimensions: 24" D x 8" H (610 mm x 205 mm)
Cable Length: 15 meters
Radar Scanner Weight: Unit 26 lbs; cable 8.35 lbs
Range Scales (Range Rings)
GMR 21—1/8 nm (1/32 nm) to 24 nm (6 nm)
GMR 41—1/8 nm (1/32 nm) to 36 nm (9 nm)
Antenna RPMs: 24 rpm
Range Ring Accuracy: 20 meters or +/- 1.5% of range scale,
whichever is greater
Bearing Accuracy: 1 degree
Minimum Range: 20 meters
Range Discrimination: 20 meters
Sensitivity and Tune Controls: Gain, Sea Clutter, Rain Clutter,
Frequency Tune
Power Output
GMR 21—2 kW
GMR 41—4 kW
FTC: Low, Medium, High
Power Input Source: 10.5–35 VDC, 28 W
Off Center Function: Look Ahead, Auto Shift, and Manual
Operating Temperature Range: -15°C to 70°C, and a relative
humidity up to 95% at 35°C
RF Transmit Frequency: 9410 ± 30 MHz
Beamwidth: Horizontal beamwidth of 3.6° nominal / vertical
beamwidth of 25° nominal
Interference Rejection: Anti-jamming algorithm
Wind Velocity: Wind speed up to 100 kts
14
Radar/Chart Synchronization: Overlay Mode; split overlay with
standard radar presentation.
Waterproofing: IEC 60529 IPX7
MARPA: Tracks up to 10 targets
GMR 21/41 Owner’s Manual
Appendix > European License Requirements and Declaration of Conformity (DoC)
European License Requirements
Declaration of Conformity (DoC)
Austria
I
Luxembourg
I
Belgium
G
The Netherlands
I
Czech Republic
I
Poland
G
Denmark
G
Portugal
G
Estonia
I
Slovakia
*
Finland
I
Slovenia
G
France
G
Spain
*
Germany
G
Sweden
G
Greece
G
United Kingdom
I
Hungary
*
Cyprus
G
Ireland
I
Malta
*
Italy
G
Iceland
G
Latvia
I
Norway
I
Lithuania
G
Switzerland
I
I­—requires an individual license for operation.
G—can be operated under a general license or license exemption.
* This product may require licensing in your country of use. Refer to the national
radio or telecommunications office or ministry.
To view the full Declaration of Conformity, see the Garmin Web site
for your Garmin product: www.garmin.com/products/gmr21/. Click
Manuals, and then select the Declaration of Conformity link.
The following table shows European License requirements for the
GMR 21/41.
GMR 21/41 Owner’s Manual
Hereby, Garmin, declares that this GMR 21/41 is in compliance with
the essential requirements and other relevant provisions of Directive
1999/5/EC.
15
Appendix > Limited Warranty
Limited Warranty
This Garmin product is warranted to be free from defects in materials or
workmanship for one year from the date of purchase. Within this period, Garmin
will, at its sole option, repair or replace any components that fail in normal use.
Such repairs or replacement will be made at no charge to the customer for parts
or labor, provided that the customer shall be responsible for any transportation
cost. This warranty does not cover failures due to abuse, misuse, accident, or
unauthorized alteration or repairs.
THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE
EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES EXPRESS,
IMPLIED, OR STATUTORY, INCLUDING ANY LIABILITY ARISING
UNDER ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE, STATUTORY OR OTHERWISE. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY VARY
FROM STATE TO STATE.
IN NO EVENT SHALL GARMIN BE LIABLE FOR ANY INCIDENTAL,
SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, WHETHER
RESULTING FROM THE USE, MISUSE, OR INABILITY TO USE THIS
PRODUCT OR FROM DEFECTS IN THE PRODUCT. Some states do not
allow the exclusion of incidental or consequential damages, so the above
limitations may not apply to you. Garmin retains the exclusive right to repair
or replace the unit or software or offer a full refund of the purchase price at its
sole discretion. SUCH REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE
REMEDY FOR ANY BREACH OF WARRANTY.
To obtain warranty service, contact your local Garmin authorized dealer or call
Garmin Product Support for shipping instructions and an RMA tracking number.
Securely pack the unit and a copy of the original sales receipt, which is required
as the proof of purchase for warranty repairs. Write the tracking number clearly
16
on the outside of the package. Send the unit, freight charges prepaid, to any
Garmin warranty service station.
Online Auction Purchases: Products sold through online auctions are not
eligible for rebates or other special offers from Garmin. Online auction
confirmations are not accepted for warranty verification. To obtain warranty
service, an original or copy of the sales receipt from the original retailer is
required. Garmin will not replace missing components from any package
purchased through an online auction.
International Purchases: A separate warranty is provided by international
distributors for units purchased outside the United States. This warranty is
provided by the local in-country distributor and this distributor provides local
service for your unit. Distributor warranties are only valid in the area of intended
distribution. Units purchased in the United States or Canada must be returned to
the Garmin service center in the United Kingdom, the United States, Canada, or
Taiwan for service.
Garmin International, Inc.
Garmin (Europe) Ltd.
1200 East 151st Street, Unit 5, The Quadrangle,
Olathe, Kansas 66062, USA
Abbey Park Industrial Estate,
Tel. (913) 397-8200 or
Romsey, SO51 9DL, UK
(800) 800-1020
Tel. +44 (0) 870.8501241 (outside the UK)
Fax (913) 397-8282
0808.2380000 (within the UK)
Fax +44 (0) 870.8501251
Garmin Corporation
No. 68, Jangshu 2nd Road,
Shijr, Taipei County, Taiwan
Tel. 886/2.2642.9199
Fax 886/2.2642.9099
GMR 21/41 Owner’s Manual
Appendix > FCC Compliance and Industry Canada Compliance
FCC Compliance
The GMR 21/41 complies with Part 80 of the FCC rules. It has
received a grant of equipment authorization, issued under the authority
of the FCC.
Industry Canada Compliance
The Garmin 21/41 Marine Radar complies with Industry Canada
Standard RSS-138.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
•Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
GMR 21/41 Owner’s Manual
17
Index
Index
A
Advanced sub tab 13
AFC mode 13
auto-detect services 10
B
Bearing Line 11
bearing reference 11
begin transmitting 9
C
center offset 11
clutter
rain 5
sea 5
configuring
Radar Page 3
cross-talk rejection 11
D
Declaration of Conformity (DoC) 15
digital navigation data 2
Display sub tab 11
E
EBL 7
enter standby 9
European License Requirements 15
18
F
Fast Time Constant. See FTC
FCC compliance 17
FTC 4
G
gain 5
Garmin Marine Network 8
guard zone 4, 6
defining 6
H
heading line 2, 11
heading sensor 8
hide/show navigation features 4
I
important information iv
M
main pages
Radar Page 3–7
manually adjust the radar 13
MARPA 4, 8–9
list 9
target 8
MARPA sub tab 12
N
navigation features 4, 11
O
orientation 10
Own Vessel Safe Zone 12
specifications 14
spinning up 2
status bar 1
P
T
product registration iii
R
radar overlay 9
Radar Page 3
configuring 3
viewing 3
Radar tab 10–13
Advanced sub tab 12
Display sub tab 11
General sub tab 10
MARPA sub tab 11
radar warming up 1
rain clutter 4
range rings 2
rings 11
S
safety feature 1
safe zone ring 12
sea clutter 4
signal strength 13
software update 3
soft keys 2
target expansion 4, 5
target history 12
Timed Transmit 10
Timed Transmit STBY Time 10
Timed Transmit XMIT Time 10
Time To Safe Zone 12
trails 4, 6
V
vector length 12
velocity reference 12
VRM 7
VRM/EBL 4
adjusting 7
W
warming up 1
warranty 16
waypoints 11
Z
zoom 4, 5
Zoom level 5
GMR 21/41 Owner’s Manual
For the latest free software updates (excluding map data) throughout the life of your
Garmin products, visit the Garmin Web site at www.garmin.com.
© 2006 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151st Street, Olathe, Kansas 66062, USA
Garmin (Europe) Ltd.
Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, UK
Garmin Corporation
No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan
www.garmin.com
Part Number 190-00665-00 Rev. B