Fujitsu P3PC-1932-01EN Photo Scanner User Manual

P3PC-1932-01EN
fi-5530C2 Image Scanner
CONTENTS
■ Regulatory Information ........................................................ ii
■ Note of Liability .................................................................... iii
■ Safety Precautions ................................................................ v
Chapter1
PREPARING THE SCANNER.................................. 1
1.1 Checking the Contents of the Scanner Package............. 1
1.2 Names of Parts ................................................................... 1
1.3 Operator panel .................................................................... 2
Chapter2
INSTALLATION OF THE SCANNER...................... 3
2.1 Installing the Scanner ........................................................ 3
2.2 Connecting the Scanner to Your Personal Computer .... 3
2.3 Installing the Scanner Software ........................................ 5
2.4 Checking Scanner Driver Operation............................... 11
2.5 Uninstalling Supplied Programs ..................................... 13
Appendix1 TROUBLESHOOTING........................................ AP-1
Appendix2 DAILY CARE ...................................................... AP-4
Appendix3 REPLACING CONSUMABLES.......................... AP-5
fi-5530C2 Image Scanner Getting Started
i
INTRODUCTION
Thank you for purchasing the fi-5530C2 Duplex Color
Scanner.
This document describes how to use fi-5530C2 and
basic operation methods. Before you start using
fi-5530C2 be sure to thoroughly read this manual to
ensure correct use.
The "fi-5530C2 Operator’s Guide" stored on the Setup
CD Rom provides useful and detailed information on
Operations when you would like to use advanced features, Daily Care for maintenance of the scanner, and
Replacing Consumables to maintain conditions for
smooth scanning. Please also read the "fi-5530C2 Operator’s Guide" for further information.
■ Regulatory Information
FCC declaration
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not
occur in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
located.
• Consult your dealer or an experienced radio/TV
technician.
FCC warning: Changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
NOTICE
The use of a shielded interface cable is
required to comply with the Class B limits
of Part 15 of FCC rules.
The length of the AC cable must be 3
meters (10 feet) or less.
ii
Canadian DOC Regulations
This digital apparatus does not exceed the Class B
limit for radio noise emissions from digital
apparatus set out in the Radio interference
Regulations of the Canadian Department of
Communications.
This Class B digital apparatus complies with
Canadian ICES-003.
Le présent appareil numérique n'émet pas de
parasites radioélectriques dépassant les limites
applicables aux appareils numériques de la classe
B et prescrites dans le Règlement sur le brouillage
radioélectrique dictées par le Ministère des
Communications du Canada.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
Bescheimigung des Herstellers /
Importeurs
Für den fi-5530C2 wird folgendes bescheinigt:
• In Übereinsstimmung mit den Bestimmungen
der EN45014(CE) funkentstört
• Maschinenlärminformationsverordnung
3.GPSGV: Der höchste Schalldruckpegel beträgt
70 dB (A) oder weniger, gemäß EN ISO 7779.
International ENERGY STAR® Program
As an ENERGY STAR®
Partner, PFU LIMITED has
determined that this product
meets the ENERGY
STAR® guidelines for
energy efficiency.
The International ENERGY
STAR® Office Equipment Program is an
international program that promotes energy
saving through the penetration of energy efficient
computers and other office equipment. The
program backs the development and
dissemination of products with functions that
effectively reduce energy consumption. It is an
open system in which business proprietors can
participate voluntarily. The targeted products are
office equipment such as computers, monitors,
printers, facsimiles, copiers, scanners, and
multifunction devices. Their standards and logos
are uniform among participating nations.
■ Note of Liability
• Do not put the substance contained in the lamp
READ ALL OF THIS MANUAL CAREFULLY
BEFORE USING THIS PRODUCT. IF THIS
PRODUCT IS NOT USED CORRECTLY,
UNEXPECTED INJURY MAY BE CAUSED TO
USERS OR BYSTANDERS.
Also, keep this manual in a safe place so that it
can be easily referred to during use of this
product.
While all efforts have been made to ensure the
accuracy of all information in this manual, PFU
assumes no liability to any party for any damage
caused by errors or omissions or by statements of
any kind in this manual, its updates or
supplements, whether such errors are omissions or
statements resulting from negligence, accidents,
or any other cause. PFU further assumes no
liability arising from the application or use of any
product or system described herein; nor any
liability for incidental or consequential damages
arising from the use of this manual. PFU disclaims
all warranties regarding the information contained
herein, whether expressed, implied, or statutory.
Use in High-safety Applications
This product has been designed and manufactured
on the assumption that it will be used in office,
personal, domestic, regular industrial, and
general-purpose applications. It has not been
designed and manufactured for use in applications
(simply called "high-safety applications" from
here on) that directly involve danger to life and
health when a high degree of safety is required,
for example, in the control of nuclear reactions at
nuclear power facilities, automatic flight control
of aircraft, air traffic control, operation control in
mass-transport systems, medical equipment for
sustaining life, and missile firing control in
weapons systems, and when provisionally the
safety in question is not ensured. The user should
use this product with adopting measures for
ensuring safety in such high-safety applications.
PFU LIMITED assumes no liability whatsoever
for damages arising from use of this product by
the user in high-safety applications, and for any
claims or compensation for damages by the user
or a third party.
About the use of mercury
Hg
Lamp(s) inside this product contain
mercury and must be recycled or
disposed of according to local, state, or
federal laws.
in your mouth as it has mercury.
• Do not breathe the chemical liquid contained in
the scanner lamps.
• Do not incinerate, crush, or shred the lamps or
scanner parts.
Trademarks
Microsoft and Window are registered trademarks
of Microsoft Corporation in the United States and/
or other countries.
ISIS and QuickScan are trademarks or registered
trademarks of EMC Corporation in the United
States.
Adobe, the Adobe logo, and Acrobat are either
registered trademarks of Adobe Systems
Incorporated in the United States and/or other
countries.
Other product names are the trademarks or
registered trademarks of the respective companies.
How Trademarks Are Indicated In
This Manual
References to operating systems (OS) are
indicated as follows:
Windows 2000
Microsoft® Windows® 2000
Professional operating system.
Windows XP
Microsoft® Windows® XP
Professional operating system
(32/64-bit),
Microsoft® Windows® XP Home
Edition operating system.
Windows
Server 2003
Microsoft® Windows®
ServerTM 2003 Standard Edition
operating system (32/64-bit).
Windows Vista
Microsoft® Windows® VistaTM
Home Basic operating system
(32/64-bit),
Microsoft® Windows® VistaTM
Home Premium operating
system (32/64-bit),
Microsoft® Windows® VistaTM
Business operating system
(32/64-bit),
Microsoft® Windows® VistaTM
Enterprise operating system
(32/64-bit),
Microsoft® Windows® VistaTM
Ultimate operating system
(32/64-bit).
To avoid unexpected injuries;
fi-5530C2 Image Scanner Getting Started
iii
Where there is no distinction between the different
versions of the above operating system, the
general term "Windows " is used.
Adobe Acrobat
This symbol alerts operators to helpful
advice regarding operation.
HINT
Adobe® Acrobat®
All the descriptions in this manual assume the
usage of Adobe Acrobat bundled with this
product. However, Adobe Acrobat may be
upgraded without notice. If the descriptions differ
from the screens actually displayed, refer to the
Acrobat’s “Help”.
A TRIANGLE symbol indicates that special care
and attention is required.
The drawing inside the triangle shows the
specific caution.
A CIRCLE with a diagonal line inside shows
action which users may not perform.
The drawing inside or under the circle shows the
specific action that is not allowed.
Manufacturer
PFU LIMITED
International Sales Dept., Imaging Business
Division, Products Group
Solid Square East Tower, 580 Horikawa-cho,
Saiwai-ku, Kawasaki-shi Kanagawa 212-8563,
Japan
Phone : (81-44) 540-4538
R
Outline characters on a colored background
show instructions users should follow.
It may also include the drawing that shows the
specific instruction.
Warning Label
The glass surface inside the ADF becomes hot
during the operation. Be careful not to touch the
glass surface inside the ADF.
All Rights Reserved, Copyright© PFU LIMITED 2007
About Maintenance
The user must not perform repairs on this scanner.
Contact the store where you purchased the scanner
or an authorized FUJITSU Image Scanner service
provider to make repairs to this product.
Warning Indications Used In This
Manual
WARNING
CAUTION
This indication alerts operators to an
operation that, if not strictly
observed, may result in severe injury
or death.
This indication alerts operators to an
operation that, if not strictly
observed, may result in safety
hazards to personnel or damage to
equipment.
Symbols Used In This Manual
ATTENTION
iv
This symbol alerts operators to particularly
important information. Be sure to read this
information.
ATTENTION
Do NOT remove, stain or scratch the
warning labels from the scanner.
Screen Examples In This Manual
The screen examples in this manual are subject to
change without notice in the interest of product
improvement. If the actual displayed screen
differs from the screen examples in this manual,
operate by following the actual displayed screen
while referring to the User's Manual of the scanner
application you are using.
The screenshots in this manual were captured
from FUJITSU TWAIN32 scanner driver,
ScandAll PRO Image Capturing Utility Software,
FUJITSU ISIS scanner driver, QuickScan Pro™
image capturing software and Adobe® Acrobat®.
■ Safety Precautions
Turn the scanner OFF if it is damaged.
If the scanner is damaged for any reason,
disconnect immediately the power plug in order
to turn out the scanner. Contact the store
where you purchased the scanner.
WARNING
Do not damage the AC cable.
Do not put liquids inside the scanner.
A damaged AC cable may cause fire or electric
shock. Do not place heavy objects on AC
cables, or pull, bend, twist, heat, damage or
modify AC cables.
Do not use damaged AC cables or power
plugs, or install any cables or power plugs to
loose wall sockets.
Use only specified AC cables and
connector cables
Use only specified AC cables and connector
cables. Failure to use the correct cables might
cause electric shock and/or equipment failure.
Please don’t use the AC cable provided with
this scanner for other devices, since this might
cause equipment failure and other troubles or
an electric shock.
Use this scanner only at the indicated
power voltage. Do not connect to multiplepower strips.
Use this scanner only at the indicated power
voltage and current. Improper power voltage
and current might cause fire or electric shock.
Do not connect to multiple-power strips.
Do not touch the AC cable with wet hands.
Do not touch the power plug with wet hands.
Doing so might cause electric shock.
Do not insert or drop metal objects in to the
scanner. Do not scan wet documents or
documents with paper clips or staples. Do not
splash or allow the scanner to get wet.
If foreign objects (water, small metal objects,
liquids, etc.) get inside the scanner, immediately
turn off the scanner and disconnect the power
plug from the power outlet, then contact the store
where you bought the scanner or the
Maintenance Service Center. Pay particular
attention to this warning in households where
there are small children.
Do not touch the inside of the scanner
unless necessary.
Do not take apart or modify the scanner. The
inside of the scanner contains high-voltage
components. Touching these components might
cause fire or electric shock.
Do not use the scanner if there is a strange
odor.
If you detect excessive heat coming from the
device or detect other problems such as smoke,
strange smells or noises, disconnect immediately
the power plug in order to turn out the scanner.
Make sure that any smoke coming from it has
stopped, before contacting the store where you
bought the scanner or an authorized FUJITSU
scanner service provider.
Wipe any dust from the power plug.
Wipe off any dust from metal parts on the
power plug or metal fittings with a soft, dry
cloth. Accumulated dust might cause fire or
electric shock.
Do not install the device in locations that
has oil smoke, steam, humidity, and dust.
Do not install the scanner in locations subject
to oil smoke, steam, humidity, and dust. Doing
so might cause a fire or electric shock.
fi-5530C2 Image Scanner Getting Started
v
CAUTION
Do not install the scanner on unstable
surfaces.
Make sure that the scanner is installed on a
flat, level surface and that none of its parts
extend beyond the surface top, such as a desk
or table. Do not install the scanner on
unstable surfaces. Install the scanner on a level
surface that is free of vibration to prevent it
from falling.
Install the scanner on a strong surface that will
support the weight of the scanner and other
devices.
Before moving the scanner, disconnect the
power plug from the power outlet.
Do not move the scanner with the power and
interface cables connected as this might
damage the cables, causing fire, electric shock
or injuries. Before moving the scanner, be sure
to disconnect the power plug from the power
outlet, and all other data cables. Make sure that
the floor is free of any obstruction.
Protect the scanner from static electricity.
Install the scanner away from strong magnetic
fields and other sources of electronic noise.
Also, protect the scanner from any static
electricity as this might cause the scanner to
malfunction.
Do not block the ventilation ports.
Do not block the ventilation ports. Blocking the
ventilation ports generates heat inside of
scanner, which may results in fire or scanner
failure.
Do not place heavy objects or stand on top
of the scanner.
Do not place heavy objects on the scanner or
use the scanner's surface top to perform other
work. Improper installation might cause injuries
and equipment failure.
Firmly insert the power plug.
Do not use aerosol sprays near the
scanner.
Do not use aerosol sprays to clean the scanner.
Aerosol sprays cause dirt and dust to enter the
scanner, resulting scanner failure and
malfunction.
Disconnect the power plug from the power
outlet when the scanner is not used for a
long period of time.
When the scanner is not going to be used for a
long period of time, be sure to disconnect the
power plug from the power outlet for safety.
Firmly insert the power plug as far it can go into
the power outlet.
Do not install the scanner in the direct
sunlight.
Avoid any contact when scanner is in use.
Avoid touching any scanner mechanism during
scanning since this may cause injuries.
Do not use the scanner immediately after
moving it from a cold place into a warm
room.
Do not use the device immediately after
moving it from a cold place into a warm room.
This may cause condensation, which might
lead to scanning errors. Let the device dry
about one or two hours before you use it.
vi
Do not install the scanner under direct sunlight or
near heating apparatus. Doing so might cause
excessive heat to build up inside the scanner,
which can cause scanner trouble or even fire.
Install the scanner in a well-ventilated location.
Chapter1
PREPARING THE SCANNER
1.1 Checking the Contents of
the Scanner Package
When you unpack the scanner package, make sure that
the package contains all the parts on the list included in
the package.
If any parts are missing or defective, contact your scanner dealer or an authorized FUJITSU scanner service
provider. Handle the scanner and accessories with care.
■ Removable Parts
The following shows the parts that can be removed from
the scanner.
ADF paper chute
Sheet guide
Pad ASSY
Pick roller
1.2 Names of Parts
This section describes the names of parts.
■ Front side
Can be removed
(2) ADF paper chute
(3) Side guide
(1) Automatic document
feeder (ADF)
(4) ADF button
(5) Operator panel
(6) Stacker
■ Rear side
(10) DC inlet
(9) USB Interface connector
(11) EXT connector
(7) SCSI ID switch
(8) SCSI Interface connector
fi-5530C2 Image Scanner Getting Started
1
1.3 Operator panel
The operator panel is located on the right side of the
scanner. The panel consists of a Function Number Display, four buttons and a LED.
Function No.
display
Function
Send to
Scan
Power button
LED
.
Name
Function
Function Number
Display
Indicates the state of the scanner. The meaning of the numbers and alphabets indicated
are explained later in this section.
Buttons
Function
Changes the Function activated
by the [Send to] button (*).
Send to
Launches the linked application software (*).
Scan
LED
Power button
Turns the scanner ON and
OFF.
-
Lights when the scanner is
turned ON.
*) About the settings on the launcher, refer to FUJITSU
TWAIN32 scanner driver help and "fi-5530C2 Operator’s Guide" on the Setup CD-ROM.
2
■ Indications on the Function
Number Display
The following shows the indications on the Function
Number Display.
Indication
Meaning
8
Lights only one time upon turning on the
scanner.
Indicates that the scanner has been turned
ON and is being initialized.
Indicates that initialization will soon be
completed.
Indicates that initialization has been completed successfully.
This status is called "Ready Status."
Indicates that a temporary error (that users
can solve) has occurred during the initialization or scanning of documents.
[U] and an error number (1, 2, 6) are displayed alternately.
To return the scanner to the ready status
([1]), press the [Scan] or [Send to] button
while the error is indicated.
Indicates that a device alarm (that users can
not solve) has occurred during the initialization or scanning of documents.
[E] and an alarm number (2 to 9, and, c, d,
F) are indicated alternately.
To return the scanner to the ready status
([1]), press the [Scan] or [Send to] button.
If this alarm occurs, turn the power off and
then on again. If the alarm is indicated after
turning on the power again, contact your
servic engineer.
P
0
1
U
E
INSTALLATION OF THE SCANNER
Chapter2
2.1 Installing the Scanner
2) Connect the AC adapter connector to the scanner’s DC inlet.
1. Place the scanner at its installation site.
For details on the scanner's dimensions and
required installation space, refer to section 7.2
"Installation Specifications" of "fi-5530C2 Operator’s Guide" on the Setup CD-ROM.
2. Attach the ADF paper chute.
Hold the ADF paper chute and insert its tabs into
the corresponding slots in the scanner as shown in
the figure below.
The Side guides of the ADF paper chute have to
face up.
3) Plug the AC cable into the outlet.
ADF paper chute
HINT
Tab
The Function Number Display and the LED
may flash for an instant when plugging the
AC cable into the outlet.
2.2 Connecting the Scanner to
Your Personal Computer
Connect either with the USB interface cable or the SCSI
interface cable.
Side guide
ATTENTION
3. Connect the AC adapter.
ATTENTION
Use only the AC adapter provided by the
manufacturer.
1) Connect the AC cable to the AC adapter.
This scanner is provided with two interfaces: Ultra SCSI and USB 2.0 /1.1. Connect only one of the USB or SCSI interface
cable.
■ Connecting with the USB
Interface Cable
1. Connect the USB interface cable to the USB
interface connector.
fi-5530C2 Image Scanner Getting Started
3
2. Connect the other end of the USB interface
cable to your personal computer.
ATTENTION
1. Insert the SCSI interface cable into the interface connector of the scanner until both sides
click.
• Be sure to use the USB cable which
•
•
comes with this scanner as an accessory. Correct operation with commercially available cables is not guaranteed.
When connecting to an USB hub, use
the first stage USB hub that is closest to
the computer. If you use the second or
later hub stages, the scanner may not
operate correctly.
If you connect the scanner with USB 2.0,
it is required that the USB port and Hub
are compliant with USB 2.0. The scanning speed may slow down if it is connected with USB1.1.
■ Connecting with the SCSI Interface Cable
2. Connect the other end of the cable to your personal computer.
ATTENTION
When using the scanner with a SCSI interface, the following SCSI interface cable and SCSI card must be purchased.
• SCSI interface cable:
Use a cable which complies with a 50 Pin Contact Shielded High-Density SCSI Device Connector for Ultra SCSI.
• SCSI card
Find the recommended SCSI card information in
the Fujitsu web site (FAQ).
http://imagescanner.fujitsu.com/
Be careful not to bend the pins of the SCSI
cable when connecting to the scanner .
The SCSI ID initially set at the factory is [5].
If the SCSI ID of another SCSI device is set
to the same ID, either change the scanner's
SCSI ID or SCSI ID of the other SCSI
device. For details on how to change the
SCSI ID, refer to "Setting the SCSI ID" in
this section.
HINT
■ Setting the SCSI ID
The factory initial setting for SCSI ID is [5].
ATTENTION
• When connecting the SCSI interface
1. Press the power button at least for two seconds to turn off the scanner if it is on. Disconnect the AC cable from the outlet.
•
2. Set the SCSI ID using the SCSI ID switch on
the back of the scanner.
cable, turn the scanner off. Be sure to
connect the SCSI interface cable first ,
and then turn on the power of the scanner and personal computer.
In a SCSI daisy chain formation, connect the scanner so that it is the terminated device.
Click
ID No.
Description
0 to 7
Can be set as the ID
8, 9
Works with the factory default value
(SCSI ID = 5).
3. Press the power button to turn on the scanner.
When the scanner is turned ON, the SCSI ID set
at step 2 is enabled.
4
2.3 Installing the Scanner
Software
FUJITSU TWAIN 32 Scanner Driver
To scan documents with this scanner, you must install a
scanner driver for operating the scanner as well as
scanning software (hereinafter called the "application")
for launching the driver and performing a scan.
The scanner drivers and application provided with the
scanner are as follows:
• Scanner Driver:
FUJITSU TWAIN 32 (-> page 5)
FUJITSU ISIS (-> page 7)
• Scanning application:
ScandAll PRO (-> page 8)
(Supports both FUJITSU TWAIN 32 and ISIS)
FUJITSU TWAIN 32 is a TWAIN-compliant scanner
driver.
To use this scanner with any TWAIN-compatible
application, install FUJITSU TWAIN 32, following the
procedure below.
■ Preparations
Do the following before installing the application:
• Unpack the Setup CD-ROM, but do not
insert the Setup CD-ROM into the CD driver
yet.
• Connect the scanner correctly to your
personal computer.
Install either of the scanner drivers above and ScandAll
PRO. The following sections describe the installation of
respective drivers and the application.
In addition, this scanner is bundled with the following
software applications. To make full use of the scanner,
try to use them together.
• Error Recovery Guide (-> page 9)
When errors occur in the scanner, you can view
information about what happened to the scanner
and how to solve the problem on the screen of
the personal computer.
• Image Processing Software Option
<Trial Version> (-> page 9)
This is an optional application for performing
binary image processing on scanned images.
• QuickScan ProTM
<Trial Version> (-> page 9)
This application complies with the ISIS standard
and it is used for scanning images. This
scanner is accompanied with a trial version of
this application.
• Adobe Acrobat (-> page 10)
This is an industry-standard application used for
creating, managing, and making use of digitalized documents in PDF format.
For details on how to connect the scanner,
refer to section 2.2 "Connecting the Scanner to Your Personal Computer" on page 3.
HINT
• Uninstall an older version of FUJITSU
TWAIN 32 if it is already installed on your
personal computer.
ATTENTION
Uninstall [Scanner Utility for Microsoft Windows] from [Add/Remove Programs] on
the control panel.
■ Installing the FUJITSU TWAIN32
Scanner Driver
HINT
How to install drivers and applications is described
below.
Screenshots taken in Windows XP are used
as examples. The displayed windows and
operations may slightly vary depending on
the operating system you are using.
1. Press the power button to turn on the scanner.
2. Turn on your personal computer and log on to
Windows.
ATTENTION
Be sure to log on as a user with "Administrator" privileges.
fi-5530C2 Image Scanner Getting Started
5
3. If the scanner is automatically detected,
[Found New Hardware Wizard] or [Add/
Remove Hardware Wizard] dialog box will
appear. Click the [Cancel] button to close the
Wizard dialog box.
ATTENTION
After you select [Yes] for installing Error
Recovery Guide, the [Choose Setup Language] dialog box appears. Select a language and follow the on-screen
instructions. The Error Recovery Guide dialog box is automatically displayed when the
installation is complete. Wait until the installation of the TWAIN driver starts.
7. Select a language for the installation on the
[Choose Setup Language] dialog box, and then
click the [Next] button.
4. Insert the Setup CD-ROM into the CD drive.
⇒ <SETUP DISK START UP SCREEN>
appears.
ATTENTION
This screen may not appear if the
"AutoPlay" setting is set to off. In this case,
find "Install.exe" in the CD-ROM using
"Explore" or "My Computer" and execute
it.
5. Click [INSTALL PRODUCTS], and then click
[TWAIN Driver].
6. The Error Recovery Guide Installation dialog
box appears.
Error Recovery Guide is an application with
which you can view on-screen information for
troubleshooting errors that may occur in the
scanner. This guide helps solve problems, so
select [Yes] to install it. You may also choose
to install it later.
6
8. Install the driver, following the on-screen
instructions.
9. When you see the [InstallShield Wizard Complete] dialog box, click the [Finish] button.
Depending on the state of the operating system, the
computer will once shut down and restart. In this case,
the computer detects the scanner when it starts up. Do
not remove the Setup CD-ROM from the CD drive until
the computer completely starts up again.
ATTENTION
Depending on the operating system you
are using, you may need to do the following.
Windows 2000:
If you see the [Digital Signature not
Found] dialog box, click the [Yes] button.
Windows Vista:
If you see the [Found New Hardware] dialog box, select [Locate and install driver
software], and then in the [User Account
Control] dialog box, click the [Continue]
button, if it is displayed.
■ Installing the FUJITSU ISIS
Scanner Driver
Screenshots taken in Windows XP are
used as examples. The displayed windows
and operations may slightly vary depending
on the operating system you are using.
HINT
1. Press the power button to turn on the scanner.
2. Turn on your personal computer, and then log
on to Windows..
The installation of FUJITSU TWAIN 32 is complete.
Next, install ScandAll PRO (-> page 8).
ATTENTION
ATTENTION
To make sure that FUJITSU TWAIN 32 is
successfully installed, perform a scan with
a TWAIN-compliant application such as
ScandAll PRO. For information about how
to scan with ScandAll PRO, refer to section 2.4 "Checking Scanner Driver Operation" on page 11.
Be sure to log on as a user with "Administrator" privileges.
3. When the scanner is automatically detected,
[Found New Hardware Wizard] or [Add/
Remove Hardware Wizard] dialog box will
appear. Click the [Cancel] button to close the
Wizard dialog box.
FUJITSU ISIS Scanner Driver
FUJITSU ISIS is an ISIS-compliant scanner driver.
To use this scanner with any ISIS-compatible
application, install FUJITSU ISIS, following the procedure below.
■ Preparations
Do the following before installing the application:
• Unpack the Setup CD-ROM, but do not
insert the Setup CD-ROM into the CD driver
yet.
• Connect the scanner correctly to your personal computer.
HINT
For details on how to connect the scanner,
refer to section 2.2 "Connecting the Scanner to Your Personal Computer" on page 3.
4. Insert the "Setup CD-ROM" into the CD drive.
⇒ <SETUP DISK START UP SCREEN>
appears.
ATTENTION
The [SETUP DISK START UP SCREEN]
may not appear if the "AutoPlay" setting is
set to off. In this case, find "Install.exe" in
the CD-ROM using "Explore" or "My Computer" and execute it.
fi-5530C2 Image Scanner Getting Started
7
5. Click [INSTALL PRODUCTS], and then click
[ISIS Driver].
Your computer will restart and detect the scanner. Do
not remove the Setup CD-ROM from the CD drive until
your personal computer completely starts up again.
ATTENTION
6. Error Recovery Guide Installation dialog box
appears.
Error Recovery Guide is an application with
which you can view on-screen information for
troubleshooting errors that may occur in the
scanner. This guide helps solve problems, so
select [Yes] to install it. You may also choose
to install it later.
ATTENTION
Windows 2000:
If you see the [Digital Signature not
Found] dialog box, click [Yes].
Windows Vista:
If you see the [Found New Hardware] dialog box, select [Locate and install driver
software], and then in the [User Account
Control] dialog box, click the [Continue]
button, if it is displayed.
The installation of FUJITSU ISIS is complete.
Next, install ScandAll PRO.
ATTENTION
After you select [Yes] for installing Error
Recovery Guide, the [Choose Setup Language] dialog box appears. Select a language and follow the on-screen
instructions. The Error Recovery Guide
dialog box is automatically displayed when
the installation is complete. Wait until the
installation of the ISIS starts.
7. Select a language for the installation on the
[Choose Setup Language] dialog box, and then
click the [Next] button.
Depending on the operating system you
are using, you may need to do the following.
To make sure that FUJITSU ISIS is successfully installed, perform a scan with a
TWAIN-compliant application such as
ScandAll PRO. For information about how
to scan with ScandAll PRO, refer to section 2.4 "Checking Scanner Driver Operation" on page 11.
ScandAll PRO
■ Installing ScandAll PRO
ScandAll PRO is software for scanning images, which is
in conformity with both TWAN/ISIS standards. Using
FUJITSU TWAIN 32 or FUJITSU ISIS together with
ScandAll PRO allows you to create document images.
ATTENTION
Be sure to log on as a user with "Administrator" privileges.
1. Insert the Setup CD-ROM into the CD drive.
⇒ <SETUP DISK START UP SCREEN>
appears.
8. Install the driver, following the on-screen
instructions.
9. When you see the [InstallShield Wiizard Complete] dialog box, click the [Finish] button.
8
2. Click [INSTALL PRODUCTS], and then click
[ScandAll PRO].
3. Select a language for the installation on
[Choose Setup Language] dialog box, and then
click the [OK] button.
4. Proceed with the installation, following the onscreen instructions.
ner. Follow the procedure below to install the trial version of QuickScan ProTM that comes with this scanner.
5. When the [InstallShield Wizard Complete] dialog box appears, click the [Finish] button.
ATTENTION
HINT
For information about the features of ScandAll PRO, refer to Help topics in ScandAll
PRO.
Be sure to log on as a user with "Administrator" privileges.
1. Insert the Setup CD-ROM into the CD drive.
⇒ <SETUP DISK STARTUP SCREEN>
appears.
2. Click [INSTALL PRODUCTS], and then click
[QuickScan Pro (Trial)].
Error Recovery Guide
If Error Recovery Guide is installed on your computer,
you can troubleshoot errors that may occur in the scanner by simply following the on-screen instructions .
If you did not install Error Recovery Guide together
with the scanner driver, follow the procedure below to
install it.
1. Insert the Setup CD-ROM into the CD drive.
3. In the [Welcome to the InstallShield Wizard for
QuickScan 4.5] dialog box, click the [Next] button.
4. Type in necessary information in the [Customer
Information] dialog box, and then click the
[Next] button.
⇒ <SETUP DISK STARTUP SCREEN>
appears.
2. Click [INSTALL PRODUCTS], and then click
[Error Recovery Guide].
3. Select a language for the installation in the
[Choose Setup Language] dialog box, and then
click the [OK] button.
4. Install the application, following the on-screen
instructions.
5. When you see the [InstallShield Wiizard Complete] dialog box, click the [Finish] button.
ATTENTION
Image Processing Software Option
(Trial)
For details on the installation of Image Processing Software Option (Trial Version), refer to the "Image Processing Software Option USER’S GUIDE."
"QuickScan ProTM" included in the Setup
CD-ROM is a trial version that can be executed for limited number of times. You can
run this trial version up to 30 times before
it is disabled. If you wish to use this product, please consider purchasing full version. (When you install the trial version,
use the displayed Serial Number.)
5. Install the application, following the on-screen
instructions.
QuickScan Pro™ (Trial)
HINT
QuickScan ProTM is image capturing software based on
the ISIS standard. By using this software together with
FUJITSU ISIS, you can scan documents with the scan-
For information about the features and
operations of QuickScand ProTM, refer to
"QuickScan Overview" or "QuickScan
Help."
Form the [start] menu, select [All Programs] -> [EMC Captiva] -> [QuickScan],
and then select a desired file.
fi-5530C2 Image Scanner Getting Started
9
Adobe® Acrobat®
Install Adobe Acrobat from the "Adobe Acrobat CDROM" provided with this scanner.
4. Install the application, following the on-screen
instructions.
HINT
Adobe Acrobat is a prerequisit for displaying manuals.
* You do not have to install Adobe Acrobat
if it is already installed on your computer.
HINT
1. Insert the Adobe Acrobat CD-ROM into the
CD-ROM drive.
ATTENTION
⇒ The [Adobe Acrobat] dialog box appears.
ATTENTION
For information about how to install Adobe
Acrobat, refer to "Read Me" that you can
view when [Readme] is clicked in the dialog box shown in step 2.
For information about how to operate
Adobe Acrobat, refer to the Help topics in
Adobe Acrobat.
Notes for using Adobe Acrobat
When scanning a paper document and
converting the image to PDF using Adobe
Acrobat, unexpected images may be output when:
1. Setting "Edge Shadow Removal" in Acrobat, and setting "Digital Endorser" or
"Black Background" options in the
TWAIN driver at the same time. Letter
strings embedded in the image or the
background may be missed.
Solution 1: Set "Edge shadow removal"
to "OFF" or set any option other than
"Adaptive" for "Color/Grayscale" and/or
"Monochrome" under "Compression" by
selecting [File]->[Create PDF]-> [From
Scanner...]-> [Optimization Options] in
Acrobat.
Solution 2: Adjust the scanning density
in the TWAIN driver.
This dialog box may not appear if the
"AutoPlay" setting is set to off. In this case,
find "AutoPlay.exe" in the CD-ROM using
"Windows Explorer" or "My Computer" and
execute it.
2. In the dialog box below, click the folder icon;
installation starts and the Setup dialog box
appears.
2. Setting "Adaptive" for "Color/Grayscale"
and/or "Monochrome" under "Compression" in Acrobat and scanning in a resolution lower than the resolution
recommended for Acrobat.
Solution: Set OPTION to something
other than "Adaptive" under "Compression."
3. Scanning a document longer than the
double letter (11x17) or A3 size, when
setting "Overscan" in the TWAIN driver,
the scan may fail.
Solution: When scanning a double letter
(11x17) or A3 size of document, do not
set "Overscan" in TWAIN driver.
3. In the dialog box below, click the [Next] button.
4. *As for detailed usage and information of
Acrobat, refer to "Create a PDF file from
a scanned document" in Acrobat Help.
ATTENTION
10
Support and User registration for Adobe
products
For details, refer to the technical support
information stored in the [Customer Support] folder on Adobe Acrobat CD-ROM.
(Note that free person-to-person support is
not available for this is bundled product.)
2.4 Checking Scanner Driver
Operation
6. In ScandAll PRO, select [Scan] on the menu,
and then select [Select Scanner].
This section explains how to check the operation of the
installed scanner driver by using ScandAll PRO.
Make sure that the scanner driver is installed properly,
following the procedure below.
■ Checking the Operation of the
Scanner Driver
1. Load the document on the scanner.
For information about how to load the document,
refer to section 1.2 in fi-5530C2 Operator's
Guide.
7. Select a scanner in the displayed dialog box.
To use FUJITSU TWAIN 32:
Select "FUJITSU fi-5530C2dj," and then click the
[Select] button.
2. Launch ScandAll PRO.
From the [start] menu, select [All Programs] ->
[ScandAll PRO] -> [ScandAll PRO].
⇒ ScandAll PRO starts up.
3. In ScandAll PRO, select [Tool] on the menu,
and then select [Preferences].
To use FUJITSU ISIS:
Select "Fujitsu fi-5530C2" and then click the
[Select] button.
⇒ The [Setup] dialog box appears.
4. On the [Scan] tab, select a driver.
To check the operation of FUJITSU TWAIN 32,
select "TWAIN."
To check the operation of FUJITSU ISIS, select
"ISIS."
8. Select [Scan] on the menu, and then select
[Scan Settings].
5. Click the [OK] button to close the [Setup] dialog
box.
fi-5530C2 Image Scanner Getting Started
11
9. In the [Scan Settings] dialog box, clear the
[Save to file] checkbox.
To use FUJITSU ISIS
On the dialog box below, configure scanning settings, and then click the [OK] button.
⇒ You are returned to the [Scan Settings] dialog
box.
12. Click the [Scan] button.
HINT
HINT
You only check the operation now, so you
do not have to save to file.
When you are using FUJITSU TWAIN 32,
you may see the TWAIN Driver setup dialog box again. If so, click the [Scan] button
on the dialog box.
⇒ The document is scanned and the scanned
10. Click [Scanner Settings].
⇒ A setup dialog box appears for you to config-
image is displayed in the [ScandAll PRO]
window.
ure scanner driver settings.
11. Configure scanner settings such as the resolution and paper size.
To use FUJITSU TWAIN 32
On the dialog box below, configure scan settings,
and then click the [OK] button.
If the scanned document image is displayed in the window, it means that the scanner driver is installed properly.
For further information about how to scan documents,
refer to "fi-5530C2 Operator’s Guide" contained in the
Setup CD-ROM.
12
2.5 Uninstalling Supplied
Programs
5. Click the [Change/Remove] button or the
[Remove] button.
The following explains how to uninstall software applications provided with the scanner.
6. When you see a confirmation dialog box, click
the [OK] button or the [Yes] button.
⇒ Upon clicking the button, uninstallation is
started.
Screenshots taken in Windows XP are used
as examples. The displayed windows and
operations may slightly vary depending on
the operating system you are using.
HINT
HINT
Displays may vary depeinding on the operating system you are using. Follow the onscreen instructions.
Examples
1. Start your personal computer.
ATTENTION
Be sure to log on as a user with "Administrator" privileges.
In Windows 2000, the window and button
names described above are as follows:
• [Add or Remove Programs] -> [Add/
Remove Applications]
• The [Changel/Remove] button -> The
[Add/Remove] button
In Windows Vista, the window and button
names described above are as follows:
• [Uninstall or Change a program] ->[Uninstall or Change]
2. Exit all applications.
3. From the [Start] menu, select [Control Panel] ->
[Add or remove Programs].
⇒ In the [Add or remove Programs] dialog box,
you can view a list of installed applications.
4. Select an application you want to uninstall as
follows:
• To remove FUJITSU TWAIN 32,
select "Scanner Utility for Microsoft Windows."
• To remove ScandAll PRO,
select "Fujitsu ScandAll PRO V1.0."
• To remove FUJITSU ISIS,
select "Fujitsu ISIS Drivers."
• To remove Error Recovery Guide,
select "Error Recovery Guide."
• To remove Software Operation Panel, (Software
Operation Panel is automatically installed
together with FUJITSU TWAIN 32/ISIS),
select "Software Operation Panel."
• To remove QuickScan ProTM,
select "QuickScan"
HINT
• For information about how to uninstall
•
Image Processing Software Option (Trial
version), refer to "Image Processing
Software Option User’s Guide."
For information about how to uninstall
Adobe Acrobat, refer to Adobe Acrobat
"Read Me."
fi-5530C2 Image Scanner Getting Started
13
Appendix1 TROUBLESHOOTING
■ Troubleshooting checklist
Symptom
The scanner is not turned on.
Check this item
Remedy
Have you pushed the power button?
Push the power button.
Are the AC cable and AC adapter properly connected to the scanner?
Correctly connect the AC cable and the AC
adapter.
Disconnect the AC cable and the AC adapter from
the scanner, then connect them again.
If this does not restore the power supply, contact
the store where you purchased the scanner or an
authorized FUJITSU scanner service provider.
Is Windows normally started up?
Push the power button again after completely
starting up Windows.
Are the documents loaded correctly on
the ADF paper chute?
Load the document correctly on ADF paper chute.
Is the ADF closed completely?
Close the ADF completely.
Is the USB cable or SCSI cable properly
connected?
Correctly connect the cable. (When a USB hub is
used, check the hub's power supply.)
(When using SCSI interface) Is SCSI ID
set correctly?
Set SCSI ID correctly by SCSI ID switch on rear
of scanner.
Does the Function Number Display indicates an alarm or an error?
When the Function Number Display indicates an
alarm or an error, refer to chapter 5 "TROUBLESHOOTING" of "fi-5530C2 Operator’s Guide"
for removing the alarm or the error.
Does the alarm state remain displayed
even after the scanner has been turned
off and back on again?
Turn off and on the power button.
If this does not eliminate the alarm state, contact
the store where you purchased the scanner or an
authorized FUJITSU scanner service provider.
Vertical lines appear in the
generated image.
Is the glass dirty?
Clean the glass following the instructions in chapter 3 "Daily Care" of "fi-5530C2 Operator’s
Guide."
The generated image is
skewed or distorted.
Are the documents loaded correctly?
Load the documents correctly.
The generated image quality is not good enough.
Are the glass or sheet guides (a white
location) clean?
Clean dirty locations.
Multi-feed errors occur frequently.
Do the documents satisfy the "Document Quality" and the "Multi feed
Detection Conditions" in the chapter 6
of "fi-5530C2 Operator’s Guide"?
Use the documents that satisfy the "Document
Quality" and the "Multi feed Detection Conditions" in the chapter 6 of "fi-5530C2 Operator’s
Guide"
Are the documents set properly in the
ADF paper chute?
Fan the documents before scanning. Correctly
align the document stack and load them on the
ADF paper chute. For details, refer to section 2.1
"Installing the Scanner" on page 3 for details.
Is the document stack thicker than
10mm?
Reduce the number of sheets in the document
stack to 10 mm thickness or less.
Is the Pad ASSY dirty?
Clean the Pad ASSY. For details, refer to section
3.2 "Cleaning the ADF" of "fi-5530C2 Operator's
Guide."
Is the Pad ASSY worn out?
Replace the Pad ASSY. For details, refer to section 4.2 "Replacing the Pad ASSY" of "fi-5530C2
Operator's Guide."
Scanning does not start.
AP-1
Symptom
Paper is not fed (pick error
occurs frequently, or document stops midway).
The generated images are
elongated.
There is a shadow on the
leading edge of the generated image?
Check this item
Remedy
Do the documents satisfy the "Document Quality" and the "Multi feed
Detection Conditions" in the chapter 6
of "fi-5530C2 Operator’s Guide"?
Use the documents that satisfy the "Document
Quality" and the "Multi feed Detection Conditions" in the chapter 6 of "fi-5530C2 Operator’s
Guide."
Is the Pick roller dirty?
Clean the Pick roller. For details, refer to section
3.2 "Cleaning the ADF"of "fi-5530C2 Operator's
Guide."
Is the Pick roller worn out?
Clean the Pick roller. For details, refer to section
4.3 "Replacing the Pick Roller" of "fi-5530C2
Operator's Guide."
Is there any debris on the document feed
path?
Remove any debris from the document feed path.
Are the Feed rollers dirty?
Clean the Feed rollers. For details, refer to section
3.2 "Cleaning the ADF"of "fi-5530C2 Operator's
Guide."
Have you adjusted the scan scale?
Select "Scanners and Cameras" in the control
panel, then click the [Device Set] tab to adjust
scale.
Are the Feed rollers dirty?
Clean the Feed rollers. For details, refer to section
3.2 "Cleaning the ADF"of "fi-5530C2 Operator's
Guide."
Have you adjusted the offset (the scanning starting position)?
Adjust the [Sub-scan Setting] on [Scanners and
Cameras] in the control panel.
fi-5530C Image Scanner Getting Started
AP-2
■ Temporary error
Indication
■ Device alarm (Permanent error)
Meaning
Indication
Meaning
U1
A paper feed error occurred.
E2
Trouble in the optical system (front).
U2
A multi feed error occurred.
E3
Trouble in the optical system (back).
U6
The print cartridge is not set.
E4
The motor fuse has blown out.
E6
Trouble in the operator panel.
E7
Trouble occurred in the internal memory
(EEPROM).
E8
The SCSI interface fuse has blown out.
E9
An error in the image memory.
Ec
An alarm in the memory.
Ed
Trouble in the SCSI interface controller.
EF
A trouble in the Background switching
mechanism.
The following shows the procedure for releasing of each
temporary error.
• "U1" error
1. Remove jammed documents.
(For details, refer to section 5.1 "Removing
Jammed Documents" of "fi-5530C2 Operator’s Guide on the Setup CD-ROM..)
2. Confirm that the documents meet the paper
conditions for scanning.
(For details, refer section 6.2 "Document
Quality" of "fi-5530C2 Operator’s Guide" on
the Setup CD-ROM.)
• "U2" error
Press the [Send to] button on the Operator Panel.
The papers that were multi fed will be ejected.
• "U6" error
This is a temporary error related with the
Imprinter option (sold separately). For details,
refer to chapter 5 "Error Message" of "fi-553PR
Operator's Guide."
AP-3
When you encounter any alarm, turn off and on the
scanner. If the alarm is still displayed on the Function
Number Display, contact the store where you purchased
the scanner or an authorized FUJITSU scanner service
provider.
Appendix2 DAILY CARE
WARNING
When operating the scanner, the
ADF’s inside glass becomes very
hot.
Before you clean inside the scanner, turn off its power and unplug
the AC adapter from the outlet. Wait
for at least 15 minutes.
Do not turn off the scanner when
you clean the Feed rollers or Eject
rollers.
■ Locations and Cycle for Cleaning
Part to clean
Pad ASSY
Standard Cleaning Cycle
Clean these parts after every
5,000 scans.
Pick roller
Feed rollers
Plastic rollers
Eject rollers
Sheet guides
■ Cleaning Materials
Glass
Ultra sonic sensor
Cleaning
Materials
Parts No.
Remarks
Cleaner F1
PA039500352
1 bottle
Moisten a cloth with
this fluid and wipe the
scanner clean.
Lint-free dry
cloth
- Commercially available one
For details about the cleaning materials, contact the
FUJITSU scanner dealer where you purchased the scanner.
ATTENTION
The scanner must be cleaned more frequently if you scan any of the following
type of sheets:
• Documents of coated paper
• Documents that are almost completely
covered with printed text or graphics
• Chemically treated documents such
as carbonless paper
• Documents containing a large amount
of calcium carbonate
• Documents written by pencil
• Documents on which the toner is not
fused sufficiently.
■ Cleaning Method
The ADF must be cleaned with a lint-free cloth moistened with the Cleaner F1.
ATTENTION
For details on the cleaning the ADF, refer to section 3.2
"Cleaning the ADF" of "fi-5530C2 Operator’s Guide"
on the Setup CD-ROM."
It may take long before the cleaner
vaporizes if a large quantity is used.
When cleaning the scanner parts,
dampen a cloth with modest quantities
of the cleaner. In addition, wipe off the
cleaner completely with a soft lint-free
cloth to leave no residue on the surface
of the cleaned parts.
fi-5530C Image Scanner Getting Started
AP-4
Appendix3 REPLACING CONSUMABLES
WARNING
During its operation, the inside
glass of the ADF becomes very
hot .
Before replacing the
consumables, turn its power off
and unplug the AC adapter from
the outlet. Wait at least
15 minutes.
The following illustrations show the locations of the
consumables. For details, refer to chapter 4 "Replacing
Consumables" of "fi-5530C2 Operator’s Guide" on the
Setup CD-ROM.
■ Replacing the Pad ASSY
To remove
To attach
■ Consumables and Replacement
Cycle
The followings are the specifications of consumables
and their recommended replacement cycles.
Description
Pad ASSY
Pick roller
Parts No.
Standard
Replacement Cycle
PA033340002
After 100,000 scans or
one year
PA033340001
After 200,000 sheets
or one year
Pad ASSY
■ Replacing the Pick Roller
Sheet guide
To purchase consumables, contact the store where you
purchased the scanner or an authorized FUJITSU scanner
service provider.
The replacement cycles above are rough guidelines
when using A4/Letter woodfree or wood containing
paper 64 g/m2 (17 lb). This cycle varies according to the
type of the used paper and how frequently the scanner is
used and cleaned.
ATTENTION
Use only the specified consumables.
Pick roller
AP-5
fi-5530C Image Scanner Getting Started
AP-6
fi-5530C2 Image Scanner Getting Started
P3PC-1932-01EN
Issue Date: June, 2007
Issued by: PFU LIMITED
Copying of the contents of this manual in whole or in part and
copying of the scanner application is prohibited under the
copyright law.
z The contents of this manual are subject to change without notice.
z PFU LIMITED is not liable whatsoever for any damages resulting
from use of this scanner and procedures described in this manual,
profit loss due to defects, and any claims by a third party.
z