Fujitsu Siemens Computers RX600 S3 Switch User Manual

PRIMERGY RX600 S3
incl. SAS version
System configurator and order-information guide
February 2007
Contents
Instructions
Configuration diagram
Configurator
0
1
2
3
4
5
6
7
8
9
10
11
12
0 System software
I
Basic unit
II Processor
III Memory
IV onboard SCSI / SAS Contr
V USB devices / optical devices
VI Hard disk drives
VII Tape Devices
VIII optional SCSI / RAID controller
IX Fibre Channel controller
X Communication / Network
XI System Management Products (RemoteView)
XII National accessories pack
Change report
PRIMERGY Server
System configurator and order-information guide
PRIMERGY RX600 S3
Status 2007-01-24
Instructions
This document contains basic product and configuration information that will enable you to configure your system via
PC-/System-Architect
Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete
PRIMERGY Rack system.
You can configure your individual PRIMERGY server in order to adjust your specific requirements.
The System configurator is divided into several chapters that are identical to the current price list and PC-/System-Architect.
Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through
the configurator by following the lines from the top to the bottom.
Section
III
Memory, example
There are X memory slots which can be equipped with XXX MB
It is permissible to make up to X passes through the memory upgrade options
S26361-XXX-XXX
Memory XXX MB
S26361-XXX-XXX
Memory XXX MB
max. X times per system
max. X times per system
X times
In one chapter you can only select as many components (here 4x) as the arrow indicates.
4x
Please note that there are information symbols which indicate necessary information.
Further information in the internet see:
http://www.primergy.com
(internet)
http://extranet.fujitsu-siemens.com/primergy
(extranet)
Prices and availability see price list and PC-/System-Architect.
Subject to change and errors excepted.
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server
2 of 17
System configurator and order-information guide
PRIMERGY RX600 S3
Status 2007-01-24
Configuration diagram PRIMERGY RX600 S3
TOP View
Slot
System unit ( I )
Extension slots
SCSI / RAID controller ( VIII )
Fiber Channel ( IX )
Communication/Network ( X )
7
6
5
Memory ( III )
Memory Board A
(2 Banks / 4 modules)
PCI-X 64-Bit / 100MHz, long
Memory Board B
(2 Banks / 4 modules)
PCI-X 64-Bit / 100MHz, long
Memory Board C
(2 Banks / 4 modules)
PCI-Express x4 ( hot-plug )
Memory Board D
(2 Banks / 4 modules)
PCI-Express x4 ( hot-plug )
occupied by PCIe RAID Controller in SAS Version
4
Processors must be plugged
in order according the picture.
PCI-Express x4 ( hot-plug )
3
Processor ( II )
PCI-X 64-Bit / 133MHz, long ( hot-plug )
2
Xeon
MP 3
PCI-Express x8 ( hot-plug )
1
Xeon
MP 4
Xeon
MP 2
Xeon
MP 1
FRONT VIEW
Accessible drives
Tape drives ( VII )
5.25"x 0.5" bay for CD/DVD
Local View LCD Display
Operating Panel
USB
5.25"x1.6" Tape Drive
Operating
Panel
USB
Video
USB
Hard disk drives ( IV ) hot-plug
SCSI Version: 5x 3.5"SCSI
USB
Video
USB
SCSI-ID 2
SCSI-ID 0
SCSI-ID 1
3.5"x1"
3.5"x1"
SCSI-ID 1
3.5"x1"
COM
SAS Version: 8x 2.5" SAS
Channel B
3.5"x1"
SCSI-ID 0
3.5"x1"
Channel A
or
2.5" SAS
2.5" SAS
2.5" SAS
2.5" SAS
2.5" SAS
2.5" SAS
2.5" SAS
2.5" SAS
Ethern
et
Ethern
et
REAR VIEW
Hot Plug Redundant Power Supply
1. PSU
2. PSU
Key:
Included in basic unit
Option
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server
3 of 17
PRIMERGY-Software Configurators and Release Lists
PRIMERGY RX600 S3
Status 2007-01-24
Start "PRIMERGY RX600 S3"
SW - Configurator 32 bit
with OEM-Software
for PRIMERGY Server
Usage of OEM SW from MS is
not possible under VMware
without OEM-Software
for PRIMERGY Server
OEM-SW is bound to HW and
is not allowed to be ordered
separately.
Exception: VMware SW
VMware-Software
- VCMS VirtualCenter Management Server
- Virtual Infrastructure 3
For all SW products please refer to the corresponding software configurator accessible via
the Extranet under Configuration & Tools, -All configurations, -Software, URL see below.
MS - Software: W **)
- Windows Server 2003 R2,
Standard Edition
Enterprise Edition
PRIMECLUSTER *)
- Clustering
- Load Balancing
- Additional loose
Client-Access-Licenses (CALs)
(not for Web Edition)
Linux - Software: L **)
- Open Enterprise Server ***)
- SuSE Linux ES (OEM): LO
- SuSE Linux ES (Support): LS
- Red Hat EL (OEM): LO
- Red Hat EL (Support): LS
CITRIX-Software for
Windows: W-MF
- Presentation Server
LoadBalancing
Additional User Licences
MultiPath, Duplex Data Manager (DDM)
W2K; W2K3 Linux (W-DDM)
Manageability Software: V
- RemoteView Software
- RemoteView Service Board
- vPMS 2006std
Details eg. version numbers are published
in the separate SW-Configurator
- Altiris Server Deployment
*) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under
http://extranet.fujitsu-siemens.com/primecluster
Backup-Software /
Application-Software: U
- ARCserve
- openSM2
**) Pay attention to the release and ordering information in PRINCE -> Operating System
http://vil.mch.fsc.net/vil/pc/vil/primergy/overview/prince/index_en.htm
Find detailed software configurators and release lists (OS-matrix / system management) under following addresses:
for internal users: http://vil.mch.fsc.net/vil/oec/special/primergy/index_en.htm
for partners:
http://vilpart.fujitsu-siemens.de/vil/oec/special/primergy/index_en.htm
Continue with PRIMERGY
HW configurator
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server
4 of 17
PRIMERGY-Software Configurators and Release Lists
PRIMERGY RX600 S3
Status 2007-01-24
Start "PRIMERGY RX600 S3"
SW Configurator EM64T
with OEM-Software
for PRIMERGY Server
Usage of OEM SW from MS is
not possible under VMware
without OEM-Software
for PRIMERGY Server
OEM-SW is bound to HW and
is not allowed to be ordered
separately.
Exception: VMware SW
VMware-Software
- VCMS VirtualCenter Management Server
- Virtual Infrastructure 3
For all SW products please refer to the corresponding
software configurator accessible via the Extranet under
"Configuration & Tools, -All configurations, -Software,
URL see below.
only
EM64T
Microsoft - Software: W
- Windows Server 2003 R2,
Standard x64 Edition
Enterprise x64 Edition
- Additional loose
Client-Access-Lizenzen (CALs)
Linux - Software *) **)
only
- SuSE Linux ES (OEM): LO
x86_64 - SuSE Linux ES (Support): LS
- Red Hat EL (OEM): LO
- Red Hat EL (Support): LS
CITRIX-Software for
only
Windows: W-MF
EM64T - Presentation Server
LoadBalancing
Additional User Licences
only
MultiPath, Duplex Data Manager (DDM)
EM64T
Windows, Linux (W-DDM)
Details eg. version numbers are published
Manageability Software: V**)
only
- RemoteView Software
EM64T - RemoteView Service Board
- RemoteView Diagnosis
- vPMS 2006std
in the separate SW-Configurator
*) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under
http://extranet.fujitsu-siemens.com/primecluster
**) Pay attention to the release and ordering information in PRINCE -> Operating System
http://vil.mch.fsc.net/vil/pc/vil/primergy/overview/prince/index_en.htm
You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses:
for internal users: http://vil.mch.fsc.net/vil/oec/special/primergy/index_en.htm
for partners:
http://vilpart.fujitsu-siemens.de/vil/oec/special/primergy/index_en.htm
Continue with PRIMERGY
HW configurator
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server
5 of 17
System configurator and order-information guide
PRIMERGY RX600 S3
Status 2007-01-24
Start PRIMERGY RX600 S3
I
Section
Basic unit
PRIMERGY RX600 S3 SCSI
PRIMERGY RX600 S3 SAS
Rack unit 4U
Rack unit 4U
SCSI basic unit with:
SAS basic unit with:
- 3 + 2 bays for 1" HDD`s (two channels)
- 8 bays for 2.5" SAS HDD`s
- 7 PCI Slots
- 6 PCI Slots
- 1x 64bit / 133MHz PCI-X slot (hot plug)
- 2x 64bit / 100MHz PCI-X slot
- 3x PCIe x4 slot (hot plug)
- 1x 64bit / 133MHz PCI-X slot (hot plug)
- 2x 64bit / 100MHz PCI-X slot
- 2x PCIe x4 slot (hot plug)
- 1x PCIe x8 slot (hot plug)
- 1x PCIe x8 slot (hot plug)
- onboard RAID 5 functionality
with 256MB Cache (BBU optional)
- SAS RAID 5 Controller
with 256MB Cache and BBU
- memory of basic units selectable via
base memory order codes
2.60GHz/4MB 7110M
S26361-K988-V410
3.00GHz/4MB 7120M
S26361-K988-V420
3.20GHz/8MB 7130M
S26361-K988-V430
3.40GHz/16MB 7140M
S26361-K988-V440
- memory of basic units selectable via
base memory order codes
2.60GHz/4MB 7110M
S26361-K988-V510
3.00GHz/4MB 7120M
S26361-K988-V520
3.20GHz/8MB 7130M
S26361-K988-V530
3.40GHz/16MB 7140M
S26361-K988-V540
PRIMERGY PRIMECENTER- Rack
SNP:SY-F1647E301-P
Installation ex works for one
server or subsystem.
Hereby the rack will be delivered
completely pre-mounted and
all wired connections are tested.
With racks 12U, 24U, 38U:
Systems and components
will be delivered installed in the rack
With racks 46U:
Systems and components
will be delivered separately
To be ordered only together with
a PRIMERGYPRIMECENTER rack
e.g.:
S26361-K826-V10x
refer configurator DC-Rack
max. 1x per System
Basic Unit including:
- 2 hot-plug power supply (redundant)
- 2 hot-plug fan modules (redundant)
- LCD-Display for LocalView (Service Display)
- 1 bay (0,5" height) for CD- or DVD-ROM
- 1x 5.25" bays FH (1,6" high) for accessible drives
- Rack- mounting kit
Systemboard with
- Intel E8501 chipset with 800MHz Frontside Bus
- 1x XEON MP dua core processor
(2nd, 3rd and 4th as option)
- 1 memory board (2nd, 3rd and 4th as option)
- Ultra 320 SCSI-controller (LSI 53C1030)
- Dual LAN-Controller 1GBit on-board
WOL-capable (BroadCom 5704)
- VGA Controller on-board
(ATI Radeon 7000M, 16MB RAM)
- Server Management Controller on-board
(RSB 2 Board optional)
- ServerView Suite Software package
incl. ServerStart, ServerBooks,
Management Software and Updates
- Interfaces:
Front side
3x USB 2.0
1x VGA (15 pin)
"Rack-mounting ex factory"
This service is to be ordered once
per installable server/storage
subsystem, in order to get the
server/storage subsystem
mounted into the PRIMERGY racks.
In case of the 46 U PRIMERGY rack,
this service has to be ordered,
to get the mounting kits and the
cables installed
Rear Side
2x USB 2.0
1x VGA (15 pin)
1x RS-232-C (serial, 9 pin)
2x RJ45 (on board LAN)
no PS/2 connection for KB / Mouse
(USB connectivity must be used instead)
Rack Mounting kit is part of the basic unit PRIMERGY RX600 S2
- 1 pair of telescopic rails (713 - 812mm)
- 1 bracket DC-PC-Rack
- 1 cable management for DC-PC-racks
This kit allows for mounting of TX/RX600 S3 in in FSC 19" DataCenter- and
PRIMECENTER- racks and all server racks conforming to EIA standard EIA-310-D for 19" racks.
Therefore the mounting kit is variable in depth from 713 - 812mm
Installation in PRIMERGY 19" Classic rack is not possible.
Due to the heat dissipation of the system, sufficent cooling couldn´t be enabled in classic rack.
Connetion for KVM switch / Rack console
- RC23 can be directly connected (both USB and PS/2 connections)
- KVM S2 series needs the KVM S2 Adapter USB<->VGA
- For ES4/8+ KVM series with PS/2 connector as well as for standard PS/2 KB / Mouse
an additional USB to PS/2 adapter must be bought additionally and connected to the RX600 S3.
The adapter offers 2x PS/2 ports.
Adaper order number, to purchase via PRIMEPOWER, is:
D:GP70P-KA01 Adapter for PS/2<->USB
- Appropriate FSC USB keyboard is S26381-K340-V1*
This keyboard also needs USB cable T26139-Y3812-V1
A
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server
6 of 17
System configurator and order-information guide
PRIMERGY RX600 S3
Status 2007-01-24
A
II
Section
Processor
A 4-way processor system requires a multi-processor operating system
Later upgrading to a four-way-processor system is also possible
VRM´s for 1st/2nd CPU are on the Motherboard, for the 3nd / 4th CPU addition VRM Modules are required.
Extension CPUs must have identical cache size and clock rate
2. CPU
S26361-F3124-E410
Xeon MP 7110M 2.60GHz
800 MHz FSB
with 4MB TLC on Chip,
heat sink and "Easy retention"
occupies socket for one CPU
max. 1x per system
S26361-F3124-E420
Xeon MP 7120M 3.00GHz
800 MHz FSB
with 4MB TLC on Chip,
heat sink and "Easy retention"
occupies socket for one CPU
max. 1x per system
S26361-F3124-E430
Xeon MP 7130M 3.20GHz
800 MHz FSB
with 8MB TLC on Chip,
heat sink and "Easy retention"
occupies socket for one CPU
max. 1x per system
S26361-F3124-E440
Xeon MP 7140M 3.40GHz
800 MHz FSB
with 16MB TLC on Chip,
heat sink and "Easy retention"
occupies socket for one CPU
max. 1x per system
S26361-F3124-E420
Xeon MP 7120M 3.00GHz
800 MHz FSB
with 4MB TLC on Chip,
heat sink and "Easy retention"
occupies socket for one CPU
max. 2x per VRM module
S26361-F3124-E430
Xeon MP 7130M 3.20GHz
800 MHz FSB
with 8MB TLC on Chip,
heat sink and "Easy retention"
occupies socket for one CPU
max. 2x per VRM module
S26361-F3124-E440
Xeon MP 7140M 3.40GHz
800 MHz FSB
with 16MB TLC on Chip,
heat sink and "Easy retention"
occupies socket for one CPU
max. 2x per VRM module
3./4. CPU
up to 3
upgrade
S26361-F3124-E800
VRM module for 3rd/4th CPU
max. 1x per system
CPU´s
S26361-F3124-E410
Xeon MP 7110M 2.60GHz
800 MHz FSB
with 4MB TLC on Chip,
heat sink and "Easy retention"
occupies socket for one CPU
max. 2x per VRM module
up to
2x
B
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server
7 of 17
System configurator and order-information guide
PRIMERGY RX600 S3
Status 2007-01-24
B
III
Section
Memory
The system can be equipped with up 4 memory boards with 2 memory banks each.
One Memory Board is allready supplied in the base unit.
Each memory board can be equipped with up to 2x 8GB = 16GB memory.
The maximal extension is 64GB with 4GB modules!
No mix of modules within one memory bank is allowed.
For each basic unit, one pair of memory modules has to be ordered with the ordercode of "Base Memory"
(either 2GB = 2x1GB, 4GB = 2x2GB or 8GB = 2x4GB)
Note**: The price of the smallest Base Memory is already included in the basic unit,
The price of the other Base Memories is the Delta to the smallest Base Memory
Additional memory extensions (Upgrade Memory) can still be configured for the standard market price.
ECC with memory scrubbing function is standard for RX600 S3.
Optional hot-spare memory functionality can be configured in the BIOS (redundant memory bank n + 1)
RX600 S3 supports the memory protection through Memory Mirroring or Memory RAID.
Memory Mirroring requires 2 or 4 Memory boards, Memory RAID requires 4 Memory boards.
see Note** above
S26361-F3072-B622
Base memory 2 GB
DDR RAM PC2-3200 ECC
with chipkill support
consisting of 2 modules
with 1 GB each
occupies one bank
1x per base system
S26361-F3072-B623
Base memory 4 GB
DDR RAM PC2-3200 ECC
with chipkill support
consisting of 2 modules
with 2 GB each
occupies one bank
1x per base system
S26361-F3072-E622
Upgrade memory 2 GB
DDR RAM PC2-3200 ECC
with chipkill support
consisting of 2 modules
with 1 GB each
occupies one bank
max. 1x per base system
S26361-F3072-B624
Base memory 8 GB
DDR RAM PC2-3200 ECC
with chipkill support
consisting of 2 modules
with 4 GB each
occupies one bank
1x per base system
S26361-F3072-E623
Upgrade memory 4 GB
DDR RAM PC2-3200 ECC
with chipkill support
consisting of 2 modules
with 2 GB each
occupies one bank
max. 1x per base system
S26361-F3072-E624
Upgrade memory 8 GB
DDR RAM PC2-3200 ECC
with chipkill support
consisting of 2 modules
with 4 GB each
occupies one bank
max. 1x per base system
S26361-F3072-E623
Upgrade memory 4 GB
DDR RAM PC2-3200 ECC
with chipkill support
consisting of 2 modules
with 2 GB each
occupies one bank
max. 2x per memory board
S26361-F3072-E624
Upgrade memory 8 GB
DDR RAM PC2-3200 ECC
with chipkill support
consisting of 2 modules
with 4 GB each
occupies one bank
max. 2x per memory board
S26361-F3125-E130
Memory Board with 2 banks
for 2 modules each
max. 3x per system
up to 3x
memory
upgrade
S26361-F3072-E622
Upgrade memory 2 GB
DDR RAM PC2-3200 ECC
with chipkill support
consisting of 2 modules
with 1 GB each
occupies one bank
max. 2x per memory board
boards
C
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server
8 of 17
System configurator and order-information guide
PRIMERGY RX600 S3 SAS
Status 2006-12-31
C
IV
Section
on-board SCSI / SAS Controller
SCSI Base Units
The system is equipped with a two channel Utra 320 onboard SCSI controller
including a full featured RAID controller with 256MB Cache (suporting the RAID level 0, 1, 5, 10, 50).
As option the on-board RAID Controller can be equipped with a Battery Backup Unit.
This on-board SCSI/RAID controller can be used for the connection of internal tapes and disks drives.
Also one channel can be used for the connection of external Tape devices in the SX10 subsystem.
The following rules apply for the cabling:
The cables for the connection of the on-board RAID controller to the disks in the system are includes in the base unit.
If an internal tape is configured, an additional SCSI cable is needed. (see section "IV Hard disk drives / Tapes" )
For the connection of external Tape devices to the on board SCSI controller, also an additional cable is needed in the system.
(plus cable to connect to the subsystem SX10, see configurator SX10)
S26361-F3128-E20
ROM Battery Backup Unit
for on-board RAID controller
max. 1x per system
Overview SCSI-cabling of a PRIMERGY RX600 S3 SCSI Base Unit
Picture 1:
Two channels for Disks
onboard
SCSI / RAID
1x3
HDD
Picture 2:
Two ch. for Disks + int. Tape
onboard
SCSI / RAID
1x2
HDD
optional
1x3
HDD
Picture 3:
One ch. for Disks + ext. Tape
onboard
SCSI / RAID
1x3
HDD
internal
external
Tape Devices
Tape Devices
optional
optional
internal
Tape Devices
29160 Contr.
29160 Contr.
external
Tape Devices
29160 Contr.
external
Tape Devices
29160 Contr.
external
Tape Devices
29160 Contr.
external
Tape Devices
29160 Contr.
external
Tape Devices
Configuration with 2 channels for Disk Drives
Picture 1
Both channels of the on-board SCSI/RAID-controller are used for SCSI disk drives (pls see pictures above).
For the connetion of internal tape devices an additonal SCSI controller is required, pls see section V SCSI-RAID controller
Configuration with 2 channels for Disk Drives plus internal Tape device
Picture 2
One channel of the on-board SCSI/RAID-controller is used for SCSI HDD (pls see pictures above).
The secound channel can be used to connect additional SCSI HDD and /or an internal tape device.
Configuration with 1 channels for Disk Drives plus external Tape device
Picture 3
One channel of the on-board SCSI/RAID-controller is used for SCSI disk drives (pls see pictures above).
The secound channel can be used to connect external Tape drives.
D
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server
9 of 17
System configurator and order-information guide
PRIMERGY RX600 S3
Status 2007-01-24
D
SAS Base Units
AB. on-board SCSI-/ SAS RAID-Controller for accessible drives and SAS HDD´s -> SAS Version
The system will be delivered with a 8-port SAS RAID controller for the connection of SAS HDD´s
This SAS RAID Controller is equipped with 256MB Cache and BBU (suporting the RAID level 0, 1, 5, 10, 50),
and can be used only for the connection of internal disks drives.
Additonally the system is equipped with a two channel Utra 320 onboard SCSI controller
This on-board SCSI controller can be used for the connection of internal or external tape devices.
The following rules apply for the cabling:
The cables for the connection of the SAS RAID controller to the disks in the system are includes in the base unit.
If an internal tape is configured, an additional SCSI cable is needed. (see section "IV Hard disk drives / Tapes" )
For the connection of external Tape devices to the on board SCSI controller, also an additional cable is needed in the system.
(plus cable to connect to the subsystem SX10, see configurator SX10)
Overview SAS / SCSI-cabling of a PRIMERGY RX600 S3 SAS Base Unit
Eight SAS ports for Disks
Two SCSI ports for int./ext. Tape
internal
8x internal
2.5" SAS HDD
integrated
SAS RAID
controller
onboard
SCSI contr.
Tape Devices
external
Tape Devices
optional
29160 Contr.
29160 Contr.
internal
Tape Devices
external
Tape Devices
external SCSI Interface
S26361-F3128-E102
external SCSI interface
plug:
1x VHDCI / UHD68(S)
max. 1x per system
E
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server
10 of 17
System configurator and order-information guide
PRIMERGY RX600 S3
Status 2007-01-24
E
V
Section
USB devices / optical devices
One of the following USB devices must be used for integrating the drivers during installation
process if no automized (e.g. Serverstart / Altiris / RIS / ADS / …) installation is done:
1) USB DVD+-RW:
S26391-F3152-L300
Traveller III DVD DL super multi drive
(USB cable included)
2) FDD USB (external):
S26391-F264-L226
external USB FDD
(USB cable included)
3) USB Keyboard:
S26381-K340-V120
KBPC PX D, professional keyboard
4) USB Mouse:
S26381-K403-L100
Optical Wheel Mouse
5) USB Memorybird:
S26391-F6046-L24
Memorybird 1GB
Additionally a monitor can be connected to the VGA 15-pin interface.
1x
S26361-F3123-E1
CD-RW / DVD drive 0.5"
24/24/24x / 8x ATAPI
CD-RW only with W2K, W3K, Linux
0.5 x 5.25", anthracite bezel
max. 1x per system
VI
Section
S26361-F3236-E1
DVD-RW 8x super multi drive
all formats, DUAL/DL, DVD-RAM
only W2K, W3K and Linux
0.5 x 5.25", anthracite bezel
max. 1x per system
Hard disk drives
HDD´s for SCSI Base Units
S26361-F3121-E173
Hard disk 73GB
10000rpm,<5,5ms, 8MB Cache
Ultra 320 SCSI (320MB/s)
Interface: Wide SCA (80-pins)
hot plug/hot replace tray
occupies 1" bay
SCSI/RAID controller necessary
max. 5x per system
S26361-F3121-E114
Hard disk 146GB
10000rpm,<5,5ms, 8MB Cache
Ultra 320 SCSI (320MB/s)
Interface: Wide SCA (80-pins)
hot plug/hot replace tray
occupies 1" bay
SCSI/RAID controller necessary
max. 5x per system
S26361-F3121-E130
Hard disk 300GB
10000rpm,<5,5ms, 8MB Cache
Ultra 320 SCSI (320MB/s)
Interface: Wide SCA (80-pins)
hot plug/hot replace tray
occupies 1" bay
SCSI/RAID controller necessary
max. 5x per system
S26361-F3121-E536
Hard disk 36GB
15.000rpm,<4ms, 8MB Cache
Ultra 320 SCSI (320MB/s)
Interface: Wide SCA (80-pins)
hot plug/hot replace tray
occupies 1" bay
SCSI/ RAID controller necessary
max. 5x per system
S26361-F3121-E573
Hard disk 73GB
15.000rpm,<4ms, 8MB Cache
Ultra 320 SCSI (320MB/s)
Interface: Wide SCA (80-pins)
hot plug/hot replace tray
occupies 1" bay
SCSI/ RAID controller necessary
max. 5x per system
S26361-F3121-E514
Hard disk 146GB
15.000rpm,<4ms, 8MB Cache
Ultra 320 SCSI (320MB/s)
Interface: Wide SCA (80-pins)
hot plug/hot replace tray
occupies 1" bay
SCSI/ RAID controller necessary
max. 5x per system
max. 5
HDD´s for SAS Base Units
S26361-F3208-E136
HD 36GB 10krpm 2.5"
10000rpm,<4,5ms, 8MB Cache
SAS 3Gb/s
hot plug/hot replace tray
max. 8x per base unit
max. 8
S26361-F3208-E173
HD 73GB 10krpm 2.5"
10000rpm,<4,5ms, 8MB Cache
SAS 3Gb/s
hot plug/hot replace tray
max. 8x per base unit
F
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server
11 of 17
System configurator and order-information guide
PRIMERGY RX600 S3
Status 2007-01-24
F
VII
Section
Tapes devices
S26361-F3128-E101
internal SCSI-Cable
for connetion of
internal Tape devices
max. 1x per system
S26361-F2848-E3
Tape drive DDS Gen5
S26361-F2848-E31 (only for OBDR)
DDS-G5 for One buttom dis. recov.
36GB, 3MB/s, U2W SCSI
Connector: HD68
without cable
incl. description (Ger/US)
data and cleaning cartridge
1.6 * 5.25", anthracite bezel
max. 1x per system
1x
S26361-F2849-E3
Tape drive VXA-2
80GB, 6MB/s, U2W SCSI
Connector: HD68
without cable
incl. description (Ger/US)
data and cleaning cartridge
1.6 * 5.25", anthracite bezel
max. 1x per system
S26361-F3224-E3
Tape drive VXA-320
160GB, 12MB/s, U160 SCSI
Connector: HD68
without cable
incl. description (Ger/US)
data and cleaning cartridge
1.6 * 5.25", anthracite bezel
max. 1x per system
S26361-F3157-E3
Tape drive LTO2HH Ultrium
200GB, 24MB/s, U160 SCSI
Connector: HD68
without cable
incl. description (Ger/US)
data and cleaning cartridge
1.6 * 5.25", anthracite bezel
max. 1x per system
as soon as available
S26361-F3459-E3
Tape drive LTO3HH Ultrium
400GB, 60MB/s, U320 SCSI
Connector: HD68
without cable
incl. description (Ger/US)
data and cleaning cartridge
1.6 * 5.25", anthracite bezel
max. 1x per system
(only in SAS Base Units)
LTO 3HH can be
can be installed
only in SAS version
G
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server
12 of 17
System configurator and order-information guide
PRIMERGY RX600 S3
Status 2007-01-24
G
VIII
Section
optional SCSI / RAID controller
B. SCSI - controller for internal and external devices.
S26361-F2399-E1
1-channel SCSI U160 Controller
Adaptec 29160
plug:
internal:
HD 50-pin & HD68
external:
HD68
without cable
64/66 PCI
3.3V and 5V tolerant signaling
max. 2x per system
max. 2x
The RAID controller can be used only for
the connection of external subsystems (SX30)
Cables for the connection from the RAID Controllers
to the subsystem see configurator SX30.
C. RAID-Controller for external Disk Arrays
S26361-F3006-E128
2-channel RAID Controller U320
LSI
320-2
128MB SDRAM ECC Cache
default with TBBU
plug: internal 2x HD68;
external: 2x VHDCI
without cable
64/66 PCI controller, 180mm
3.3V and 5V tolerant signaling
max. 2x per system
max. 2x
SAS RAID controller for JBOD subsystems
S26361-F3215-E1
8 port SAS RAID Controller
LSI
MegaRAID SAS 8344 ELP
256MB Cache with ECC
optional BBU
SAS 3Gb/sec
4 internal / 4 port external
PCIe x4, 198mm
full height bracket
max. 1x per system
S26361-F3215-E10
Cache Battery Backup Unit
max. 1x per Controller
It is only a maximum cable
length of 2m supported
Controller plus optional BBU
require a full hight PCI slot.
H
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server
13 of 17
System configurator and order-information guide
PRIMERGY RX600 S3
Status 2007-01-24
H
IX
Section
Fibre channel controller
Qlogic controller
Emulex Controller
No mix and match for Qlogic and
Emulex Fibre channel controllers
possible
S26361-F3097-E1
2GBit/s FC Controller
Qlogic
QLA2340, full height bracket
1 channel 2GBit/sec FC Controller
LC Interface for 50µm Fiber
PCI-X 64Bit / 133MHz, 170mm
3.3V / 5V tolerant signaling
max. 3x per system
Qlogic controller
max. 3x or
Emulex controller
max. 3x / 4x
In SAS version
max. 3x PCIe controller
can be installed
S26361-F3306-E1
4GBit/s FC Controller
Emulex
LPe1150, full height bracket
1 channel 4GBit/sec FC Controller
LC Interface for 50µm Fiber
PCIe x4, 170mm
max. 3x / 4x per system
S26361-F3306-E2
4GBit/s FC Controller
Emulex
LPe11002, full height bracket
2 channel 4GBit/sec FC Controller
LC Interface for 50µm Fiber
PCIe x4, 170mm
max. 3x / 4x per system
All controllers for the connection of external storage systems are delivered without cables.
For the configuration of external cabling see the configurator for external storage systems.
For Fibre Channel SAN also other componets like switches, SFPs and optical wires are
orderable (for details see price liste)
I
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server
14 of 17
System configurator and order-information guide
PRIMERGY RX600 S3
Status 2007-01-24
I
X
Section
Communication / Network
on-board LAN Controller
Dual Gbit Ethernet Contr. on-board
BroadCom BCM5704
ext: 2 x RJ 45 connector
Teaming: Failover, Load Balancing
The Intel LAN Controllers Pro 1000MT, 1000MF, 1000PT, 1000PF
can be used with the on-board controller in Teaming Mode
With Broadcom on-board adapters for Gigabit Ethernet must be used
for the teaming the Broadcom driver.
Two onboard LAN ports can likewise educate a team.
A) Single Port LAN Adapter PCI-X
S26361-F3054-E1
Gigabit Ethernet Contr. 1000SX
Eth. Ctrl 1x1Gbit PCI-X Pro/1000MF LC
Intel PRO/1000 MF Server Adapter
PCI-X (PCI64/133), min 165 mm
ext:LC-connector
max. 3x per system
S26361-F3053-E1
Gigabit Ethernet Controller 1000TX
Eth Ctrl 1x1Gbit PCI-X Pro/1000MT Cu
Intel PRO/1000 MT Server Adapter
PCI-X (PCI64/133)
ext: for RJ45-connector, Cat 5
max. 3x per system
3x
B) Dual Port LAN Adapter PCI-X
S26361-F3011-E1
Gigabit Ethernet Controller Dual 1000TX
Eth Ctrl 2x1Gbit PCI-X PRO/1000MT Cu
Intel Pro/1000MT Dual Port Server Ad.
PCI-X (PCI64/133)
ext: for RJ45-plug, Cat 5
max. 1x per system
C) Single Port LAN Adapter PCIe
S26361-F3241-E1
Gigabit Ethernet Contr. 1000SX
Eth. Ctrl 1x1Gbit PCIe Pro/1000PT
Intel PRO/1000 MPT Server Adapter
PCIe x1
ext:LC-connector
max. 3x / 4x per system
S26361-F3242-E1
Gigabit Ethernet Controller 1000TX
Eth. Ctrl 1x1Gbit PCIe Pro/1000PF
Intel PRO/1000 PF Server Adapter
PCIe x4
ext: for RJ45-connector, Cat 5
max. 3x / 4x per system
In SAS version
max. 3x PCIe controller
can be installed
3x / 4x
D) Dual Port LAN Adapter PCIe x4
while stocks last
S26361-F3143-E1
Gigabit Ethernet Contr. dual 1000TX
Eth. Ctrl 2x1Gbit PCIe PRO/1000P Cu
Intel Pro/1000P dual Server Adapter
PCIe x4, 170mm
ext: for RJ45-plug, Cat 5
connection with Cat 5 cabling
SW: VLAN, Fast & Gbit Etherchannel
max. 3x / 4x per system
S26361-F3228-E1
Gigabit Ethernet Controller Dual 1000TX
Eth Ctrl 2x1Gbit PCIe PRO/1000PT Cu
Intel Pro/1000PT dual Server Adapter
PCIe x4
ext: for RJ45-plug, Cat 5
max. 3x / 4x per system
J
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server
15 of 17
System configurator and order-information guide
PRIMERGY RX600 S3
Status 2007-01-24
J
Section
XI
System Management Products (RemoteView)
S26361-F1790-E221
RemoteView Software V5.0
Installation and configuration of
RemoteView Web and LAN FrontEnd
RSB, BMC-Manager, RTDS, FreeDOS
and online manuals
S26361-F2425-E103
RSB S2 LP 3HU
RemoteView Service Board S2
Low Profile Version with 3 U bracket
for one standard PCI-slot
incl. cables and RV SW
max. 1x per system
S26361-F2425-E305
RSB S2 LP external power supply
RemoteView Service Board S2
Low Profile external power supply
including power cable
with Euro- and Euro socket connector
Section
XII
National accessories packs
System will be shipped with two power cords ICE320 C14->C13 for rack installation.
Country specific power cords are not required.
End PRIMERGY RX600 S3
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server
16 of 17
System configurator and order-information guide
PRIMERGY RX600 S3
Status 2007-01-24
Change Report
Date
Order number
Changes
2007-01-24
2007-01-24
2007-01-24
2007-01-16
2007-01-16
2006-12-19
2006-12-14
2006-11-28
2006-11-15
2006-11-15
2006-11-15
2006-11-15
2006-11-15
2006-11-15
2006-11-15
2006-11-15
2006-08-25
2006-08-25
2006-08-25
2006-08-25
2006-08-25
2006-08-25
2006-08-25
2006-08-25
2006-08-25
2006-02-13
S26361-F3124-E200
S26361-F3124-E361
S26361-K988-V122
S26361-F3215-E10
S26361-F3215-E1
S26361-K988-V510-540
S26361-K988-V5xx
S26361-F3241x-E1
S26361-F3124-E311
S26361-F3124-E262
S26361-F3124-E282
S26361-F3124-E304
S26361-K988-V112
S26361-K988-V312
S26361-K988-V322
S26361-K988-V332
S26361-F3124-E440
S26361-F3124-E430
S26361-F3124-E420
S26361-F3124-E410
S26361-F3128-E800
S26361-K988-V440
S26361-K988-V430
S26361-K988-V420
S26361-K988-V410
VRM module for 3rd/4th CPU - no longer available
Processor Xeon MP 3.66GHz 1MB - no longer available
Rack mountable server 19" (4U) with processor Xeon 3.66GHz / 1MB SLC - no longer available
Cache Battery Backup Unit for 8 port SAS RAID Controller - now available
8 port SAS RAID Controller - now available
Rack mountable server 19" (4U) SAS basic unit - now available
SAS Base Units added
Singel Port PCIe LAN controller - now available
Processor Xeon MP 3.16GHz 1MB - no longer available
Processor Xeon MP 7020 3.16GHz 2x1MB - no longer available
Processor Xeon MP 7030 2.80GHz 2x1MB - no longer available
Processor Xeon MP 7041 3.00GHz 2x1MB - no longer available
Rack mountable server 19" (4U) with processor Xeon MP 3.16GHz 1MB - no longer available
Rack mountable server 19" (4U) with processor Xeon MP 7020 3.16GHz 2x1MB - no longer available
Rack mountable server 19" (4U) with processor Xeon MP 7030 2.80GHz 2x1MB - no longer available
Rack mountable server 19" (4U) with processor Xeon MP 7041 3.00GHz 2x1MB - no longer available
Processor Xeon MP 7140M 3.40GHz 16MB 800MHz - now available
Processor Xeon MP 7130M 3.40GHz 8MB 800MHz - now available
Processor Xeon MP 7120M 3.00GHz 4MB 800MHz - now available
Processor Xeon MP 7110M 2.60GHz 4MB 800MHz - now available
VRM module for 3rd/4th CPU - now available
Rack mountable server 19" (4U) with 64-bit Xeon MP Dual Core processor 7140; 16MB TLC - now available
Rack mountable server 19" (4U) with 64-bit Xeon MP Dual Core processor 7130; 8MB TLC - now available
Rack mountable server 19" (4U) with 64-bit Xeon MP Dual Core processor 7120; 4MB TLC - now available
Rack mountable server 19" (4U) with 64-bit Xeon MP Dual Core processor 7110; 4MB TLC - now available
first draft
Fujitsu Siemens Computers Enterprise Products PRIMERGY Server
17 of 17
Download PDF

advertising